FUJITSU TWAIN 32 02 User Manual

P3PC-1382-07ENC2  
FUJITSU TWAIN 32 Scanner Driver  
Scanner Utility for Microsoft® Windows®  
Version 8.18  
User's Guide  
For Microsoft® Windows® 95 and Windows NT®  
(* For Windows® 98, Windows® Me, Windows® 2000, Windows® XP  
and Windows ServerTM 2003, refer to Version 9.18 User’s Guide.)  
Trademarks  
Microsoft, Windows, Windows NT and Windows Server are registered trademarks of Microsoft  
Corporation in the United States and/or other countries.  
Intel, MMX, Pentium are registered trademarks of Intel Corporation.  
Adobe, Acrobat are the trademarks or registered trademarks of Adobe Systems Incorporated.  
Adaptec is a registered trademark of Adaptec Inc.  
EZ-SCSI is a trademark of Adaptec Inc.  
Other product names are the trademarks or registered trademarks of the respective companies.  
ii  
Organization  
This manual explains how to install and use this driver, and how to use the TWAIN scanning  
utility.  
• TWAIN  
This section gives an overview of the TWAIN specification.  
• Installation  
This section explains the procedure for installing the environments in which this driver may  
operate.  
• Using the Driver  
This section explains how to use the driver.  
• Using the Utilities  
Use of the following utilities is explained:  
Gamma Pattern Editor  
FUJITSU Scanner Control Center  
Firmware Updater  
• Trouble shooting  
This section explains the possible causes of error messages and operation errors and the  
corresponding recommended actions.  
• Appendix  
The appendix contains the specifications of image scanners.  
iii  
Contents  
iv  
v
1. Outline  
1.1. Characteristics of this Driver  
This driver complies with TWAIN regulations V1.9 (the latest version as of June 2006)  
which are global standards for image scanners. The driver can be used in all TWAIN-  
compliant applications.  
This driver also supports an image scanner that has the "double-sided scan" function. If the  
application supports continuous scan, a double-sided document can be scanned.  
1.2. Operating Environment  
This driver can be used in the following systems:  
A personal computer (recommended: Intel Pentium 100MHz or higher) on which one of the  
following operating systems are installed  
Microsoft® Windows® 95  
Microsoft® Windows NT® Server Version 4.0  
(Installation of Service Pack 3 or later recommended)  
Microsoft® Windows NT® Workstation Version 4.0  
(Installation of Service Pack 3 or later recommended)  
In case of Windows® 98, Windows® Me, Windows® 2000, Windows® XP, or Windows ServerTM 2003,  
FUJITSU TWAIN32 Version 9.18 is installed. Refer to “FUJITSU TWAIN32 Version 9.18 User’s  
Guide”  
Adaptec® SCSI adapter or Fujitsu FMV SCSI adapter  
In some cases, the driver may not operate with the above systems. Please check in  
advance with your place of purchase.  
Notes are provided on the accepted SCSI adapters in README.TXT, which is included  
in the installation media. Please read these notes before use.  
Adaptec® EZ-SCSITM Pro Version 4.5 or later or the following 32-bit versions of ASPI  
Manager (included, for example, in the Adaptec SCSI installer for Windows® 95/Windows  
NT® or on Fujitsu SCSI driver disk V1.2):  
Windows® 95, Windows® 98, Windows NT® 4.0  
V4.01 or later  
Windows® 2000, Windows® Me  
V4.60 or later  
Windows® XP, Windows ServerTM 2003  
V4.70 or later  
In case of Windows® 98, Windows® Me, Windows® 2000, Windows® XP, or Windows ServerTM 2003,  
FUJITSU TWAIN32 Version 9.18 is installed.  
Refer to ”FUJITSU TWAIN32 Version 9.18 User’s Guide“  
RAM of 32 megabytes or more (64MB or above is recommended)  
Free hard disk space of 10 megabyte or more (Except the range for the Image storing.)  
CD-ROM drive (required for installation)  
Mouse (recommended)  
1
     
1.3. Explanatory Notes  
The descriptions in this manual are prepared based on the following rules:  
Menus and buttons  
The menus and buttons used in the program description are enclosed in [ ].  
Example: [File] menu, [OK] button  
Keyboard  
The keytop indications comply with the standard keyboard of the Fujitsu FMV series.  
Major differences between the Fujitsu FMV keyboard and other keyboards are shown below.  
FMV keytops  
Alt  
Other possible keytops  
Previous screen, GRPH  
CTRL  
Ctrl  
Esc  
ESC  
Enter  
Return,  
Shift  
SHIFT  
Back space  
F1  
Backspace, BS  
PF1, f-1  
Terms related to mouse operation  
Terms related to major mouse operations are explained below.  
Click:  
To press and release the mouse button  
Double click: To quickly press the mouse button twice  
Drag:  
Move the mouse while keeping the mouse button pressed  
Notes on operation procedures  
If some menus need to be operated in a certain order, the procedural order is described as  
follows:  
[A] - [B] - [C]  
In accordance with this description, operation [A] is executed first, followed by [B] and [C]  
in that order.  
Figures  
Figures and screen operations in this guide refer to Microsoft® Windows® 2000. They are  
also followed when using other operating systems.  
Note that the expressions may vary with the type of scanner connected.  
2
 
1.4. Explanation of terms  
IPC option board  
IPC-2/2D in this guide refers to the IPC-2 and IPC-2D image processing circuit.  
IPC-3/3D in this guide refers to the IPC-3 and IPC-3D option board.  
IPC-4D in this guide refers to the IPC-4D option board.  
3
 
2. TWAIN  
2.1. TWAIN  
TWAIN is the specification that defines the standard software protocol and application  
programming interface (API) for data exchange between a software application program and an  
image input device such as the image scanner.  
[TWAIN development background]  
In the past, development of a new scanner inevitably required the development of a compatible  
driver and a sample (demonstration) program exclusively designed for the new scanner. As the  
scanner is upgraded, the driver may need to be upgraded as well to maintain its compatibility  
with the upgraded scanner. Therefore, the use is most likely to be restricted to one specific  
scanner model to avoid the complication of learning new operation methods and replacing the  
peripheral driver, etc., involved in scanner replacement.  
In view of the incompatibility among different scanners and peripheral equipment and the  
accompanying inconvenience, there was a demand for standardization of the related hardware  
and software, and TWAIN was established as a result.  
The user may now choose among all the input devices and software (driver or application  
programs) conforming to the TWAIN standard, and configure a most suitable system for himself,  
without being restricted to the products of a certain series or a certain manufacturer.  
4
   
2.2. TWAIN Application  
TWAIN mainly applies to the following three software components:  
Application software  
Source manager  
Source  
The components are related to each other as shown below.  
Application software  
(photo retouching software, etc)  
Source manager  
(TWAIN.DLL/TWAIN_32.DLL, etc)  
Source  
(Image scanner control of the driver, etc)  
Image scanner, etc.  
Figure TWAIN Application  
5
 
3. Installation  
3.1. Preparation  
1. Check that the operating system is installed correctly.  
2. Check that the SCSI adapter is installed to the computer.  
3. Check whether the SCSI driver and ASPI manager are installed correctly and operating.  
Note.  
Version 4.01 or later of the ASPI Manager is required (For Windows® 2000 or Windows® Me,  
ASPI manager must be version 4.60 or later; For Windows® XP, ASPI manager must be  
version 4.70 or later). Use Explorer or My computer to check the version number of the  
WNASPI32.DLL file.  
4. If the previous version was installed, first confirm that it has been uninstalled (deleted).  
When uninstalling old versions, select [Control Panel] – [Add or Remove Programs] on the [Start]  
menu and uninstall “Scanner utility for Microsoft Windows”.  
5. Confirm that there is sufficient free space on the hard disk to install the software.  
6. Turn off the personal computer.  
7. Connect the scanner to your PC.  
Refer to “Operator’s Guide” of the scanner for scanner connection.  
In case of Windows® 98, Windows® Me, Windows® 2000, Windows® XP, or Windows ServerTM  
2003, FUJITSU TWAIN32 Version 9.18 is installed. Refer to “FUJITSU TWAIN32 Version 9.18  
User’s Guide”  
6
   
3.2. Starting Installation  
The screen and operations will differ slightly depending on the OS that is being used.  
1. Turn on the scanner.  
2. Turn on your PC and Log on to Windows®.  
When using Windows NT® 4.0, log on as an administrator.  
The scanner may be detected automatically, and the "Update Device Driver Wizard"  
window is displayed.  
In this case, Click [Cancel] button to close this Wizard window.  
3. Insert the Scanner Driver CD-ROM into the CD-ROM drive.  
<SETUP DISK START UP SCREEN> is displayed.  
This Dialog is not displayed automatically when "Auto play" setting of your PC is off.  
In this case, please run “Install.exe” in this CD-ROM directly using “Explore” or “My  
computer”.  
7
 
4. Click [INSTALL PRODUCTS].  
(* Depending on the scanner model, the different screen may appear.)  
5. Click [TWAIN Driver]  
(* Depending on the scanner model, the different screen may appear.)  
Depending on the scanner model, the screen which confirms whether “Error  
Recovery Guide” is installed or not is displayed.  
In this case, click [OK] button, and install Error Recovery Guide.  
8
6. Select the language you use in [Choose Setup Language], then click [OK] button.  
7. Click [Next >] button.  
8. Read the information of README File, and then click [Next >] button.  
9
9. Carefully read the License Agreement, and then click [Yes] button if you agree.  
If you click [No] button, the installation is stopped.  
10. Confirm Destination Folder, and then click [Next >] button.  
Usually, it is not necessary to change Destination Folder.  
11. Confirm Components you install, and then click [Next >] button.  
Usually, it is not necessary to change the selection of Components.  
10  
12. Confirm Program Folder, and then click [Next >] button.  
Usually, it is not necessary to change the Program Folder’s name.  
13. Click [Next >] button, and copying files is started.  
14. Confirm the check boxes, and then click [Next] button.  
Usually, it is not necessary to change check status.  
When “Boot the FUJITSU Scanner Control Center” is checked, Scanner Control  
Center is started after this installation is completed.  
11  
When “Register the application in startup of START” is checked, Scanner Control  
Center is started automatically whenever Windows is started.  
About Scanner Control Center, refer to Section 6.  
15. Select “Yes, I want to restart my computer now”, and then click [Finish] button.  
16. After the restart, the scanner is detected.  
Now, the installation of scanner driver is completed.  
12  
3.3. Uninstall  
The uninstall process removes the software and returns the hard disk to its pre-installation state.  
When you want to remove this scanner driver program from your PC, uninstall by the following  
procedures.  
1. Turn on your PC and Log on to Windows®.  
When using Windows NT® 4.0, log on as an administrator.  
2. Close all of the applications on Windows®  
3. Select [Control Panel] from [Start] menu.  
The [Control Panel] is displayed.  
4. Double-click [Add/Remove Programs] from the icon list of the [Control Panel].  
The properties of [Add/Remove Programs] is displayed.  
5. Select "Scanner Utility for Microsoft Windows" from the "Install/Uninstall" list.  
6. Click [Add/Remove] button.  
7. When the confirmation dialog is displayed, click [OK] button if you are ready to uninstall.  
8. When uninstallation is completed, click on [Finish] button.  
Image files that have been scanned and saved will not be deleted.  
If other TWAIN-compliant applications and drivers have been installed and you are  
asked whether or not to delete files shared with them such as the TWAIN Manager,  
select [NO] to avoid deleting them.  
13  
 
4. Using the Driver  
4.1. Selecting the Driver  
To use this driver from the TWAIN application, select "FUJITSU <Product ID>" from the  
TWAIN data source (driver) selection screen. For general application, the data source selection  
screen is displayed by selecting the [Select Scanner] or [Acquire ...] menu. Refer to the  
instruction manual for the application used for details.  
4.2. Screen Configuration  
Scanning Area settings  
Preview window  
Image scanner name  
Setting file name  
Data size  
Message line  
Button control  
Image scan related data  
Figure Main Dialog  
14  
     
4.2.1. Linkage to Image Processing Software Option  
When the “Enable Software IPC” checkbox is marked after installation of “Image Processing  
Software Option” (sold separately), there appears setting items of Image Processing Software  
Option in a part of the Setting Window for TWAIN Driver.  
Mark this checkbox.  
Setting items of “Image Processing  
Software Option” are displayed here.  
You can change the settings of Image  
Processing Software Option here.  
The ”Image Processing Software Option” version 2.1 or later is required for settings  
on the window of TWAIN Driver.  
For details about the Image Processing Software Option, refer to the “Image  
Processing Software Option User’s Guide”.  
The following pages contain the explanation and operation description for each part.  
15  
 
4.3. Displaying Driver Information  
Image scanner name  
The model name, option port name, and capacity of internal scanner memory (in units of  
megabytes) of the connected image scanner are displayed.  
If no image scanner is connected, this field is blank.  
The type of IPC option board is displayed if an image-processing option board is installed in  
the scanner.  
IPC-3/3D may not be detected normally, as it is affected by the version number of the  
machine type and device. In this case, "IPC2" is displayed.  
Preview window  
Ruler  
The preview window is used to display the temporary image of read data and for setting the  
"Scanning Area."  
For settings, see "Scanning Area" later in this manual. Also see the description of the  
[Preview] button later in this manual.  
Ruler  
The large divisions are labeled as "Unit". The scale also varies with the selected scanner.  
Message line  
The message line is the bottom line of the dialog in which a brief explanation of an input  
item or a setting item is displayed when the mouse cursor is moved over the item.  
Data size  
The approximate amount of data per image when data is scanned in the present option.  
Note.  
This value is the amount of uncompressed data. The size of the stored file will differ from this  
value and is usually smaller if image compression is chosen and the image is compressed.  
16  
 
4.4. Setting Information on Image Scanning  
Current side  
When a scanner that allows duplex scanning is used, specifies the page which sets the image  
scanning information.  
To scan using the same settings as those for "Front side" and "Back side," clear the checks in  
the "Individual Setting" checkbox on the "Front" and "Back" tabs. A single "Duplex" tab  
will be displayed at the left so that the same image scanning information can be set for  
"Front side" and "Back side."  
To scan using different settings for "Front side" and "Back side," check the "Individual  
Setting" checkbox on the "Front" and "Back" tabs. Two tabs, "Front" and "Back," will be  
displayed at the left. Select each tab and enter the desired settings.  
This is only effective when ADF (Duplex) is selected for the method of paper feed. For  
scanner types which permit duplex scanning, see "Relevant Image Scanner Specification" in  
the Appendix.  
Resolution  
Specifies the number of pixels (dots) per inch.  
Select a predefined resolution or [Custom] from the list.  
[Customize] enables detailed settings by a pixel unit.  
By marking [Predefine] checkbox, you can select one from three predefined settings as  
[Normal], [Better], [Best] to scan documents instead of configuring settings by yourself.  
Otherwise, you can change the details of the predefined settings on the [Resolution Setting]  
window, which appears when you click on the […] button.  
17  
 
Resolutions for Image modes (“Color”, “Grayscale”, and “Black &White”) of the each  
predefined settings are changed corresponding to the selection of the Image Type.  
* Click [Default] button to return the resolutions to the default value.  
High resolution produces finer images, meanwhile requires more memory that leads to  
longer scanning time.  
The supported resolution depends on the type of scanner and the options installed.  
Refer to "Relevant Image Scanner Specification" in the Appendix.  
Paper Size  
Specifies a document size for scanning.  
Select a standard size or [Custom] size (can be registered up to three) from the list.  
Window for customizing the paper size will appear when you click on […] button besides  
the list. On this window, you can change the order of the paper size in the list.  
[Custom] button : Used for configuration of a custom size.  
[Up] button  
: Used for shifting the order of the selected document size upward.  
: Used for shifting the order of the selected document size downward.  
[Down] button  
You can register up to three sizes as the customized document sizes.  
18  
[Custom Paper Size Setting] window will appear when you click the [Custom] button. Enter  
the size of the document to be scanned. (When entering the size, specify the paper size by  
width x length to the scanning direction.)  
Some paper sizes may not be accepted by your device. Refer to "Relevant Image Scanner  
Specification" in Appendix.  
Name :  
Enter the name of the customized setting to be displayed in the list.  
Width, Length :  
To specify a custom paper size, use the scroll bar or enter the paper  
size directly. The unit specified in [Option]-[Generic]-[Unit/Scaling]  
will be applied to the unit in this window.  
Scanning Area  
Specifies the start position, width and length for the image scan. The maximum allowable  
size is the paper size selected previously.  
In addition, the minimum size is 1.000 inch, 26 millimeters, or pixels (number of dots per  
inch) according to the unit that has been set.  
"Left":  
The left end of the scan area on the scanned document (X coordinate)  
"Top": The top end of the scan area or the scanned document (Y coordinate)  
"Width": The width of the scan area  
"Length": The length of the scan area  
These values are related to one another in the following way:  
0 left end coordinate < (paper width - minimum scan area size)  
0 top end coordinate < (paper length - minimum scan area size)  
Minimum value width (paper width - left end coordinate)  
Minimum value length (paper length - top end coordinate)  
19  
Scan Type  
Selects the feeding device.  
The image scanner uses a document bed called the flat bed as well as an automatic document  
feeder (ADF) for feeding scanned document. The ADF usually enables the documents to be  
scanned only once. The flat bed allows scanning the same documents repeatedly.  
Flat bed  
Scans a document placed on the flat bed of the device.  
ADF (Front Side)  
Scans the documents on the device's automatic document feeder (ADF). Here, only the  
front sides are scanned.  
ADF (Duplex)  
To scan both the front and the back of a page, select this option.  
If this option is selected, the documents are scanned in the "front to back to front to  
back ..." order.  
This option can be used only for scanner models that support duplex scanning.  
The "Duplex Function" requires that the calling application supports "continuous scan."  
If the application does not support "continuous scan," only the data for the front side of  
the page is passed to the application.  
Some scanner models do not support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
Long page (Front Side)  
Scans a document longer than the paper size which can be specified by [Paper Size].  
In this case, only the front sides of documents are scanned.  
When this option is selected, the "Paper Size Setting" dialog box opens. Specify the size  
of the document to be scanned.  
* While the "Long page" is specified, the preview window cannot be displayed and the  
scanning area cannot be specified.  
* In case of some scanner models, while the "Long page" is specified, color and grayscale  
settings can not be selected in [Image mode].  
(Refer to “Relevant Image Scanner Specification” in the Appendix.)  
* Depending on the scanner, [Resolution] setting should be set to less than 400 dpi.  
* The "Long page" is not displayed in the [Scan Type] dropdown list if not supported by the  
device. See "Relevant Image Scanner Specification" in the Appendix.  
Long page (Duplex)  
Scans a document longer than the paper size which can be specified by [Paper Size].  
If this option is selected, the documents are scanned in the "front to back to front to  
back…" order.  
20  
ADF (Back Side)  
Scans the documents on the device's automatic document feeder (ADF).  
Here, only back sides are scanned.  
Note.  
To specify duplex scanning, the number of copies designated should be based on the  
number of pages, not the number of paper sheets. In other words, one original with a front  
and back is regarded as two pages.  
Image Mode  
Selects an image mode for scanning the image.  
Select a corresponding image mode from the list.  
Black & White  
Scans data by using the fixed threshold binary, black-and-white. Distinguishes black  
from white by the setting in the "Threshold" of "Scanning Parameter". This scanning  
mode is suitable for scanning line drawings and text documents.  
Halftone (Dither)  
Scans data using the halftone processing, with dithering or error diffusion. Uses the  
patterns set in "Halftone" to simulate data in black-and-white. Selection of built-in  
dithered patterns or error diffusion (not supported by some device models) is allowed.  
This scanning mode is suitable for scanning images containing light and shadow such as  
a photograph.  
Gray scale  
Scans data using 256-level monochrome gray scale. Light and shade in photographs can  
be represented with greater fidelity. This scanning mode employs far more memory  
than the Black & White mode.  
Some versions of the scanner do not support this scanning mode. For details contact the  
retail store where the device was purchased.  
4bit Gray scale  
Scans data using 16-level monochrome gray scale. Data size is smaller than "Gray  
scale" selected.  
Some versions of the scanner do not support this scanning mode. For details contact the  
retail store where the device was purchased.  
Automatic separation  
Scans data distinguishing line drawing from photograph image.  
If this option is selected, the line drawing part is scanned using "Black & White," and  
the photograph part is scanned using "Halftone". This information is most suitable for  
documents containing both photographs, and line drawings or text.  
Some scanner models do not support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
21  
SEE (Selective Edge Emphasis)  
Scans data using the halftone processing and emphasizes line drawings and text. This  
option is most suitable for emphasizing only text of documents containing both  
photographs and text.  
Some scanner models do not support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
24bit Color  
Scans data using 24 bits color. This mode is suitable for scanning color photograph and  
employs far more memory that Gray scale mode.  
Only color scanner models support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
256 Color  
Scans data using 256 colors.  
Data size is smaller than "24 bit Color" selected.  
Please note that the image quality of "256 Color (8 bit)" is inferior to the case of "24 bit  
Color ". Choose "24 bit Color" for higher quality.  
Only color scanner models support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
8 Color  
Scans data using 8 colors.  
Data size is smaller than “256 Color” selected.  
Please note that the image quality of "8 Color" is inferior to the case of "24 bit Color"  
and "256 Color (8 bit)". Choose "24 bit Color" for higher quality.  
Only color scanner models support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
Black & White  
Specifies the processing method when "Black & White" is specified in "Image Mode".  
Static Threshold  
Executes simple binary processing based on the "Threshold" setting.  
SDTC, DTC mode  
To enable the auto binary function of the image scanner, specify this option.  
If this option is selected, the "Threshold" setting will be disabled.  
In addition, auto binary has two modes: " SDTC Mode" and "DTC Mode". These  
modes can be set using the "Advance" dialog box.  
"DTC Mode", however, is limited to the image processing options. Therefore, only  
scanner models that have image processing options support "DTC Mode". See  
"Relevant Image Scanner Specification" in the Appendix.  
SDTC mode (Floating Slice)  
This option enables scanning and fine binary processing for documents whose  
backgrounds are other than white such as newspapers.  
Some scanner models do not support this option. See "Image Scanner Specification" in  
Appendix.  
22  
Advanced DTC  
Scan in fine binary mode regardless of the document.  
Normal binary mode can’t scan very well faintly toned documents, documents with  
colored background, or documents with color charts. Choose this to scan these  
documents clearly.  
Halftone  
Select the halftone pattern for halftone scanning from the built- in pattern list.  
Select the desired halftone pattern for displaying the obtained image. This setting is  
effective when "Halftone" or "Automatic Separation" is selected in "Image Mode".  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
Dither Pattern 0  
Executes pattern processing that is suitable for scanning a dark photograph.  
Dither Pattern 1  
Executes pattern processing that is suitable for scanning a dark-colored document  
containing both text and photographs.  
Dither Pattern 2  
Executes pattern processing that is suitable for scanning a light photograph.  
Dither Pattern 3  
Executes pattern processing that is suitable for scanning a light-colored document  
containing both text and photographs.  
Download Pattern  
Executes processing using the dithered download pattern specified in the dithered  
download file (described later). Some scanner models do not support this function. See  
"Image Scanner Specification" in Appendix.  
Error Diffusion  
Error Diffusion minimizes the difference between the pixel density of the scanned image  
and the pixel density of the printed image to create better reproduction of a scanned  
photograph.  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
23  
Scanning Parameters  
For fine scan adjustments.  
Since there is no fixed set of values, set by trial and error.  
Brightness:  
Sets the brightness of the overall image.  
Specify the brightness with a number in the range of 1 (bright) to 255 (dark).  
To darken the overall image, increase the value of the setting. To brighten the overall  
image, decrease the value.  
This parameter can be set if "Halftone" or "Automatic Separation" is selected for "Image  
Mode."  
Threshold:  
Sets the threshold value by which the black and the white of black-and-white images are  
distinguished. Specify a number in the range of 1 (bright) to 255 (dark). This parameter  
can be set only if "Black & White" is specified for "Image Mode."  
In addition, if "DTC mode" is selected, the scanner will automatically use the  
appropriate threshold value. As a result, the set value cannot be changed.  
If the light color in the scanned document is read as black, increase the threshold value.  
To eliminate light- colored areas in the scanned document, decrease this value.  
Contrast:  
Sets the contrast of light and shadow in a scanned image.  
Specify the contrast with a number in the range of 1 (low [soft]) to 255 (high [sharp]).  
The contrast can be set if "Gray Scale" is selected in "Image Mode."  
If this value is increased, the dark part of the image is shown darker and the light part is  
shown lighter.  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
24  
4.5. Specifying Driver Operation  
[Preview]  
Scans in a preliminary image based on set values, and displays the image in the preview  
window.  
Before actual scanning, the preview function can be used to display the entire document for  
specifying the desired scan area.  
Some models do not support this function. See "Relevant Image Scanner Specification".  
[Scan]  
Scans the specified scan range based on set values.  
The following "progress indicator" is displayed during scanning to show the progress of the  
scan operation. To stop scanning, click the [Cancel] button.  
The character string indicates the data transfer mode used between the driver and the  
application.  
Progress indicator  
[Close] / [OK]  
Closes the dialog box without scanning.  
If a setting is changed, the changed setting is saved in the initial value file.  
[Reset]  
Restores the current setting values to the status immediately after the window is opened.  
25  
 
[Help]  
Displays online help. When the [F1] key is pressed, help information regarding the item on  
which the cursor is placed is displayed.  
Note.  
Depending on the application used help information may not be displayable with the [F1] key.  
This is because the driver operation is controlled through the application and the [F1] key may be  
used differently in each application program.  
Help information can be displayed by pressing the [F1] key while holding down the [Ctrl] or [Shift]  
key.  
[Option]  
Displays the "option dialog" for setting device-specific functions. See Section 4.7, "Setting  
Option" described later.  
[Advance]  
Displays the "advance dialog" for settings related to color variance and image processing.  
[Config]  
Displays the "basic scan dialog" for managing the settings file and for setting simple scan  
dialog switching.  
[About]  
Express the version of this driver by clicking this button.  
26  
4.6. Setting "Scanning Area"  
Specify the scanning area in the preview window as follows:  
Setting:  
1. Press the left mouse button to specify the origin (top left corner) of the scanning area.  
(The cursor appears as a "+".)  
2. Drag the mouse to show the outline of the scanning area. (As the cursor moves, a range  
frame is shown.)  
3. Release the left mouse button again to set the range (bottom right corner) of the scanning  
area.  
Movement:  
1. Move the cursor into the range frame. (The cursor appears as a hand.)  
2. Press the left mouse button. (The cursor changes to a fist.)  
3. Drag the mouse to move the range frame.  
4. Release the left mouse button to set the current range.  
Cancellation:  
The range frame can be canceled by either of the following ways:  
Click the left mouse button outside the range frame (inside the scan document).  
Select other paper types.  
27  
 
4.7. Setting Options  
The "option dialog" is used to set device-specific functions and the items that differ depending  
on whether the scanner used supports them.  
The option specification is divided into "Rotation", "Job/Cache", "Generic", "Imprinter  
(Endorser)", "Start Up", “Filter” and “Compression”.  
The supported options depend on the scanner. See "Relevant Image Scanner Specification" in  
the Appendix. (  
is displayed for options that cannot be used.)  
The option dialog in this driver is explained below.  
The commonly used buttons are explained first.  
[OK]  
Enables the new setting, and terminates the option dialog box.  
[Cancel]  
Disables the new setting, returns the setting to the previous value, and terminates the  
processing.  
[Help]  
Displays online help.  
28  
 
The options are described below:  
4.7.1. Rotation  
Figure Option dialog (Rotation)  
Flip Side Rotation  
Specifies the binding of the document when both sides are scanned using ADF.  
Book  
Outputs the scanned image for both sides as is.  
Select this option to scan documents bound on the left or right side  
Fanfold  
Outputs the scanned image of the backside rotated 180 degrees.  
Select this option to scan documents bound on the top or bottom (Front side and  
backside are printed conversely.)  
* When scanning from the top to bottom for the printing direction of the document, this  
setting outputs the image with the front and backsides printed in the same direction.  
29  
 
Rotation Degree  
Outputs the scanned image rotated to the right or left 90 degrees.  
0.0 degree  
Outputs the scanned image as is.  
90.0 degree  
Outputs the scanned image rotated 90 degrees to the right (clockwise).  
-90.0 degree  
Outputs the scanned image rotated 90 degrees to the left (counterclockwise).  
180.0 degree  
Outputs the scanned image rotated 180 degrees (top and bottom reversed).  
Automatic Size and Skew detection  
Disable  
This option outputs the image as it was scanned.  
End of Page Detection  
Scanning with the ADF and page length detection selected will output data for the page  
size detected.  
The image data output will adjust to the page length detected for each page including  
smaller size pages.  
Data cannot be output for page sizes greater than the length setup in [Page Size].  
This function does not work properly for some applications.  
Automatic Deskew  
When scanning with the ADF, this option detects skew of the document being fed and  
automatically corrects the skew.  
Automatic Page Size Detection  
Scanning with the ADF and Automatic Page Size Detection selected, the output will  
adjust to the page size detected.  
Document skew can be detected and can be corrected for the output image.  
Output data size will be equal to each document scanned in a multi page scan. When  
page size is detected incorrectly, set up the [Page size] to the largest size page in the set.  
For example, With Automatic Page Size Detection is selected, it also need to select a  
Paper Size (example: Double Letter 11"x17") in the set. If any paper size within the  
30  
selected (Double Letter) paper size range is used for scanning, the output will adjust to  
the page size detected.  
(However, in case of fi-4860C/fi-4860C2/fi-4990C/fi-5650C/fi-5750C, this function is  
not dependent on the setting of [Paper size] because these scanners always scan  
documents as the maximum paper size and detect the paper size from the scanned data.)  
This function does not work properly for some applications.  
However, some detection cannot be corrected for example, an unfixed long image,  
folded corner, document has uneven width for the length of the page.  
This function becomes effective only when scanning with the ADF.  
(It may detect incorrectly when this function is chosen with flat bed scanning.)  
In case of fi-5750C, this function can work correctly with flat bed scanning when  
“Document holding pad (black)” option (sold separately) is attached on the scanner.  
Black Background  
If it is selected, the outside of document paper becomes black by using black  
background during scanning.  
White Background  
Use it to activate "Overscan". Both [White Background] and "Overscan" need to be  
selected for making Overscan effective.  
If "Overscan" is not selected, [White Background] functions the same as [Disable].  
This option may not be supported for some scanners. See "Relevant Image Scanner  
Specification" in the Appendix.  
Priority  
Setup for speed versus automatic document size detection.  
Select a small value when scanning speed is the higher priority.  
Select a large value when document detection accuracy is the higher priority.  
Priority can only be setup when [Automatic Page Size Detection] is selected at [Automatic  
Size and Skew Detection].  
If the selection of [Automatic Page Size Detection] do not makes this function selectable,  
you do not need to setup this function.  
Overscan  
This function makes the scanned images larger than the original documents by adding  
margins. This option is available only when [Black Background] or [White Background] is  
selected for [Automatic Size and Skew detection].  
31  
This option may not be supported for some scanners. See "Relevant Image Scanner  
Specification" in the Appendix.  
32  
4.7.2. Job/Cache  
Figure Option dialog (Job/Cache)  
Caching  
Specifies whether to pre-read (cache) when a document is scanned. This option enables  
faster scanning.  
If processing of the application being used slows down and scanning stops, this option can  
be used to prevent degradation of the scanning speed. (The effect, however, depends on the  
environment being used.)  
None  
Caching is not performed.  
Read ahead  
One document page is scanned, and the data is pre-read and stored in PC memory (main  
memory of the personal computer).  
Ram cache  
Prereads the allowable amount based on the allocated memory size and stores the data in  
PC memory.  
A memory size between 1 and 200 MB can be set.  
Use Memory on Scanner  
Pre-reads using the memory installed in the scanner (displayed only if supported by the  
scanner).  
33  
 
Use Both Memory  
Pre-reads using memory of both Scanner and PC (displayed only if supported by the  
scanner).  
Batch Detection  
The application can detect documents on a specific type of form (special paper). The  
application must support this function.  
None  
No detection. Scanning is done without change.  
Include and Continue  
After the special paper is detected, scanning continues. The data on the special paper is  
also valid.  
Include and Stop  
After the special paper is detected, scanning stops. The data on the special paper is also  
valid.  
Exclude and Continue  
After the special paper is detected, scanning continues. The data on the special paper is  
excluded and will not be transferred to the application.  
Exclude and Stop  
After the special paper is detected, scanning stops. The data on the special paper is  
excluded and will not be transferred to the application.  
This option may not be supported for some scanners. See "Relevant Image Scanner  
Specification" in the Appendix.  
Multifeed Detection  
This option detects a multifeed (occurs when two or more documents are sent) based on the  
set condition.  
If a multifeed is detected when this setting has been turned on, the device will stop and an  
error message output.  
None  
Multifeed detection is not performed.  
Hardware Setting  
A multifeed is detected based on the device setting.  
Check thickness  
The thickness of the transmitted document is checked by the sensor in the device.  
A multifeed is detected by detecting changes in the thickness when more than one  
document is sent.  
34  
 
Check length  
The length of the transmitted document is checked by the sensor in the device.  
A multifeed is detected by detecting changes in the length when more than one  
document is sent.  
Check thickness and length  
The thickness and length of the transmitted document are checked.  
Check overlapping  
The overlapping of the transmitted document is checked by the sensor in the device.  
A multifeed is detected by overlapping when more than one document is sent.  
Check overlapping and length  
The overlapping and length of the transmitted document are checked.  
For example, the detection accuracy can be improved by using [Check thickness] or [Check  
overlapping] for continuous scanning of forms that have different lengths and [Check length]  
for scanning of forms that have different thicknesses.  
Depending on scanner model, the selectable items are different. Refer to “Relevant Image  
Scanner Specification” of Appendix.  
Pre-Pick  
It specifies whether a document is picked and carried in front of the scanning position before  
starting scanning operation at the ADF scanning.  
Disable  
Pre-Pick is not performed.  
A document is picked and carried in front of the scanning position, after starting  
scanning operation.  
Enable  
Pre-Pick is performed.  
A document is picked and carried in front of the scanning position, before starting  
scanning operation.  
Panel setting  
The setting of device is followed.  
* When selecting “Enable,” you can scan faster than when selecting “Disable,” because of  
Pre-Pick process.  
When selecting “Enable,” if you cancel during the ADF scanning, a document remains in  
the scanner in the Pre-Pick status.  
35  
Check Over-skew  
The skew of the transmitted document is supervised during the ADF scanning.  
When an over-skew is detected, the scanner is stopped and an error message is displayed.  
* The image data of the skewed document is deleted.  
* This functions, only when “Multifeed Detection” is enabled.  
Blank page skip  
This option skips blank pages (blank pages or completely black pages) during ADF  
continuous scanning.  
Marking this check box, this function is enabled.  
*This function can be used if “Ram cache” or “Use Both Memoryis selected.  
If an item other than “Ram cache” or “Use Both Memoryhas been selected in the “Cache  
Mode:” and this check box is marked, it will change to “Ram cache”.  
In case of Black&White or Halftone (In case of binary)  
For White pages, use the [Black Dots Ratio] slider bar to set the skip condition. For black  
pages, use the [White Dots Ratio] scroll bar to set the skip condition.  
The value displayed to the right of the scroll bar displays the garbage ratio(*1). If a  
scanned document is below this value, it is recognized as a blank page. The setting range  
is OFF(- -) and 0.2% to 3.0% (in increments of 0.2%).  
*1: Ratio of black dots included in the scanning area (for white pages)  
In case of Color or Grayscale  
Use the slider bar to set the skip condition in five stages from 1 to 5.  
To make the blank pages easy to skip, increase the value of the setting.  
36  
<If blank page skip does not operate properly>  
If a blank page is scanned, increase the value set.  
If scanning is skipped up to the required document, decrease the value set.  
*
When “Black Background” is selected in [Automatic Size and Skew detection], the  
Blank page skip may not operate properly.  
When Scanned image has many background noises, the Blank page skip may not operate  
properly.  
37  
4.7.3. Generic  
Figure Option dialog (Generic)  
Unit/Scaling  
This option selects the unit for the scanning area and preview window. One inch is  
calculated as 25.4 millimeters. When inches are converted to millimeters, values are  
rounded off.  
Note.  
The TWAIN specifications require that the data width be arranged in units of 32 bits.  
As a result, a difference of up to 31 dots can be included, depending on the value set.  
38  
 
4.7.4. Imprinter (Endorser)  
Figure Option dialog (Imprinter)  
Enable Imprinter (Endorser)  
Specifies enabling or disabling the imprinter function of the device.  
When the option is selected, the scanned documents are imprinted according to the  
instructions below. This applies only to the imprinter option. Therefore, the function is  
supported only with the scanner which supports imprinter option(s). See "Relevant Image  
Scanner Specification" described in the Appendix.  
Disable  
Imprinting is not performed.  
Enable  
Prints on documents using imprinter by the settings below.  
In this case, it prints on the back side of documents after scanning.  
Therefore, the printing is not included in a scanning result.  
Depending on scanners, two imprinters can be installed and one of them can be selected to  
use.  
In this case, "Enable" is displayed as follows.  
Pre-Imprinter (Printing before scanning, and on the front side of documents)  
Prints on documents using the imprinter installed in front part of the scanner.  
In this case, it prints on the front side of documents before scanning.  
Therefore, the printing can be included in a scanning result.  
39  
 
Post-Imprinter (Printing after scanning, and on the back side of documents)  
Prints on documents using the imprinter installed in rear part of the scanner.  
In this case, it prints on the back side of documents after scanning.  
Therefore, the printing is not included in a scanning result.  
* [Pre-Imprinter] and [Post-Imprinter] cannot be used at the same time.  
Y Offset (Printing)  
Specifies Y Offset from the edge of the original for the placement of printing. See "Relevant  
Image Scanner Specification" in the Appendix because the standard value specified here  
depends on the device.  
Direction (Printing)  
Specifies the printing direction of endorsement strings. When printing from the head of  
strings against to the direction of scanning, designate “Top to Bottom”. And when printing  
from the tail of strings against to the direction of scanning, designate “Bottom to Top”  
However, see the “Relevant Image Scanner Specification” described in the Appendix since  
the available settings depend on the device.  
Font (Printing)  
Specifies the type of character from the followings.  
Horizontal  
:
:
:
Printing direction  
Vertical  
Horizontal-Narrow  
Available settings vary depending on your scanner. Refer to “Relevant Image Scanner  
Specification” in the Appendix.  
Bold  
The imprinter string is outputted with bold font.  
Available settings vary depending on your scanner. Refer to “Relevant Image Scanner  
Specification” in the Appendix.  
40  
Initial Value (Counter)  
Designates the initial count when the Imprinter String is set, including a counter value. See  
the "Relevant Image Scanner Specification" described in the Appendix since the  
programmable values range depends on the device.  
Counter Step (Counter)  
Designates the counter increment of the set counter values. In other words, this value is  
added to or subtracted from the counter each time one original is scanned.  
An increment of 0, 1, or 2 may be specified. Usually, 1 is designated for a single-sided  
original, and 2 for a double- sided original.  
Counter (Counter)  
Designates whether to increase or decrease the specified step value.  
Imprinter String (Endorser)  
Specifies the imprinter string.  
The following characters can be outputted by the Imprinter.  
Alphabet Letters  
Numeric Characters  
Symbols  
: A-Z, a-z  
: 0, 1-9  
: !”#$%&’()*+,-./:;<=>?@[\]^_`{|}~  
: (Space)  
Other  
(*The space is ignored when it is entered at the head of [String:].)  
The following definitions can be used. They may also be selected from the menu, which is  
displayed by clicking on " ".  
%YYYY: The year is printed in four digits using the Western calendar.  
%YYY: The year is printed using the two digits of the Japanese calendar (current, or Heisei  
era).  
%YY:  
The year is printed in the last two digits of the Western calendar.  
%MMM: An English abbreviation of the month is printed; for example, JAN for January  
and FEB for February.  
41  
%MM: The month is printed in two digits; for example, 01 for January and 12 for  
December.  
%M:  
The month is printed using one or two digits; for example, 1 for January and 12  
for December.  
%DD: The day is printed using two digits; for example, 03 for the 3rd day of the month  
and 26 for the 26th day of the month.  
%D:  
The day is printed using one or two digits; for example, 3 for the 3rd day of the  
month and 26 for the 26th day of the month.  
%HH: The hour is printed using two digits of the 24-hour clock; for example, 08 for 8:00  
a.m. and 14 for 2:00 p.m.  
%H:  
The hour is printed using one or two digits of the 24-hour clock; for example, 8 for  
8:00 a.m. and 14 for 2:00 p.m.  
%NN: The minute is printed using two digits; for example, 02 for 8:02 a.m. and 48 for  
2:48 p.m.  
%N:  
The minute is printed using one or two digits; for example, 2 for 8:02 a.m. and 48  
for 2:48 p.m.  
%Nud: A counter value is printed by N digits which increases or decreases with each page.  
Programmable digits of the counter is 5 and 8 and described as "%05ud" and  
"%08ud" respectively. (See the "Relevant Image Scanner Specification" described  
in the Appendix since the programmable digits depend on the device.)  
The initial counter and the methods of increasing and decreasing values can be  
specified as explained above under the heading "Counter."  
This specification is only permitted at the end of an Imprinter String (Endorser).  
Sample  
Displays printed examples of the Imprinter String (Endorser) designated above.  
Note.  
The printed counter, date, and time do not always look like the sample because the scanning  
option takes precedence.  
42  
4.7.5. Start Up  
Set up the Power Mode, Low-Speed Feeding and Scanner Operation Panel.  
In some scanner models, displayed dialog box or setup item may be different or even  
[Startup] dialog box may not be displayed.  
In case of model fi-4110CU / fi-4110C(M3091DC) / fi-4210C(M3092DC)  
In case of model fi-4120C / fi-4120C2 / fi-4220C / fi-4220C2 / fi-4530C  
/ fi-5120C / fi-5220C / fi-5530C  
Figure Option dialog (Start Up)  
43  
 
In case of model fi-5750C  
In case of model fi-5650C  
Figure Option dialog (Start Up)  
44  
Power Mode  
Quick Start Mode  
This mode keeps the lamp on regardless the scanner’s operating condition, which saves  
times for lamp to become steady.  
Low Power Mode  
To save the power consumption, this mode turns the lamp off, if the scanner is not  
operated for 14 minutes.  
Enable Low Speed Feeding  
This is to specify to obtain a high quality image.  
This function reduces times of start/stop during the scanning to obtain a smooth and high  
quality image.  
Prefer Scanning Speed  
This mode makes scanning speed becomes faster in color/grayscale scanning.  
When checking this check box, scanning speed becomes faster, but image quality is slightly  
deteriorated.  
Check this check box, when giving priority to scanning speed over image quality.  
Scanner Operation Panel  
Enable Scanner Panel  
This is to specify whether the operator panel is enabled or not. If this is checked, button  
operation on the operator panel becomes effective. (Note that the operator panel is  
enabled only during the driver is activating.)  
Enable Scanner Dial  
Specifies whether the value indicated by the density dial on the scanner is reflected on  
scanning or not.  
This setting is valid when both “Enable Scanner Panel” and this checkbox are checked.  
With this density dial, the density can be set by five levels.  
45  
If moving the density dial to the UP direction, the density changes [Normal] >>[Darker  
scanning]>>[Dark scanning]. If moving the density dial to the Down direction, the  
density changes [Normal]>>[Lighter scanning]>>[Light scanning]. If the dial is in the  
center, the scanning density is [Normal].  
Enable [Duplex] button  
This specifies whether the [Duplex] button (to switch simplex and duplex) on the  
scanner operator panel is enabled.  
And, it distinguishes whether to scan from the ADF, or from the Flat Bed (FB), and  
changes automatically.  
If this box is checked,  
when a document is on the ADF, scanning is started from the ADF.  
And when no document is on the ADF, scanning is started from the FB.  
Scanning changes [Simplex] >> [Duplex]>> [Simplex] each time the [Duplex] button is  
pressed.  
ADF/FB Automatic change  
It distinguishes whether to scan from the ADF, or from the Flat Bed (FB), and changes  
automatically.  
When a document is on the ADF, scanning is started from the ADF.  
And when no document is on the ADF, scanning is started from the FB.  
Enable [Send to] button  
Specifies whether the preview is started by pressing the [Send to] button on the device.  
Enable FB Scanning Start  
Specifies whether Scanning is started by closing the Flat bed cover.  
When setting the document on the Flat bed and closing the Flat bed cover, scanning  
starts.  
Enable [Scan] Button  
Specifies whether scanning is started by the [Scan] button.  
46  
4.7.6. Filter  
Set the filter processing in this dialog.  
The filter name is displayed in the list box.  
While checking the checkbox in the left of the filter name, the filter processing is applied to  
scanned image.  
When selecting a filter name and clicking [Property] button, the setting dialog of the filter is  
displayed.  
Figure Option dialog (Filter)  
The type of filter and the setting details are explained below.  
47  
 
Page Edge Filler  
Eliminates the blemish around the paper edges by covering the area in (Black or White)  
color.  
Color  
Select a color to paint over the image frame.  
Can select "White" or "Black".  
Please specify either white or black to match the background color of the document.  
Filled Area  
[Unit]  
Select a unit from “Inches”, “Millimeters”, and “Pixels”  
[Up], [Down], [Left], [Right]  
Specify the paint area from each side of the scanned image in numbers.  
[Up] : Input width from the top edge of the image.  
[Down] : Input width from the bottom edge of the image.  
[Left]  
: Input width from the left edge of the image.  
[Right] : Input width from the right edge of the image.  
Each value should be set in the following ranges.  
0 < [Up] + [Down] < [Image Length]  
0 < [Left] + [Right] < [Image Width]  
If any values are out of these ranges, this function may not work.  
48  
Digital Endorser  
Character string, such as the alphabet and number, is added on the data of the scanned image.  
By using this filter, you can attach a name, a date, a time or a serial number on the scanned  
images and manage them.  
Printing  
Specify the beginning position of the character string to output on the scanned image  
data.  
X Offset: Specify the position of the width direction from the left end of document.  
Y Offset: Specify the position of the length direction from the top of document.  
Unit:  
Select either “mm” or “inch” as the unit of offset value.  
Counter  
Specify the rule of the counter value used in the String.  
Initial Value:  
Step:  
Specify the initial count when the scanning starts.  
Specify the counter increment / decrement.  
Counter:  
Select whether to increase or decrease the specified step value.  
For example) In case of Initial Value”= 0, “Step”= 2, “Counter”= Increment  
0, 2, 4, 6, 8.....  
String  
Specify the output string.  
The following characters can be outputted by the Imprinter.  
Alphabet Letters  
: A-Z, a-z  
: 0, 1-9  
Numeric Characters  
49  
Symbols  
Other  
: !”#$%&’()*+,-./:;<=>?@[\]^_`{|}~  
: (Space)  
(*The space is ignored when it is entered at the head of [String:].)  
The following definitions can be used. They may also be selected from the menu, which  
is displayed by clicking on " ".  
%YYYY: The year is printed in four digits using the Western calendar.  
%YYY:  
The year is printed using the two digits of the Japanese calendar (current, or Heisei  
era).  
%YY:  
The year is printed in the last two digits of the Western calendar.  
%MMM: An English abbreviation of the month is printed; for example, JAN for January  
and FEB for February.  
%MM:  
%M:  
The month is printed in two digits; for example, 01 for January and 12 for  
December.  
The month is printed using one or two digits; for example, 1 for January and 12  
for December.  
%DD:  
%D:  
The day is printed using two digits; for example, 03 for the 3rd day of the month  
and 26 for the 26th day of the month.  
The day is printed using one or two digits; for example, 3 for the 3rd day of the  
month and 26 for the 26th day of the month.  
%HH:  
%H:  
The hour is printed using two digits of the 24-hour clock; for example, 08 for 8:00  
a.m. and 14 for 2:00 p.m.  
The hour is printed using one or two digits of the 24-hour clock; for example, 8 for  
8:00 a.m. and 14 for 2:00 p.m.  
%NN:  
%N:  
The minute is printed using two digits; for example, 02 for 8:02 a.m. and 48 for  
2:48 p.m.  
The minute is printed using one or two digits; for example, 2 for 8:02 a.m. and 48  
for 2:48 p.m.  
%Nud:  
A counter value is printed by N digits which increases or decreases with each page.  
Programmable digits of the counter is 5 and 8 and described as "%05ud" and  
"%08ud" respectively. (See the "Relevant Image Scanner Specification" described  
in the Appendix since the programmable digits depend on the device.)  
The initial counter and the methods of increasing and decreasing values can be  
specified as explained above under the heading "Counter."  
This specification is only permitted at the end of an Imprinter String (Endorser).  
Sample  
Displays the output examples of the String specified above.  
Note.  
The counter, date, and time do not always look like the sample because this string is output  
during scanning.  
50  
4.7.7. Compression  
Click this tab and mark the check box to enable or disable JPEG compression for data transfer  
from the image scanner. (This function is available only for Color or Grayscale scans.)  
Figure Option dialog (Compression)  
Imprinter String (Endorser)  
Converts scanned image data into JPEG format for transfer. Because of smaller data size,  
data transfer time is shorter than that of ordinary method (when the check box is not  
marked).  
Jpeg Quality  
Specifies data compression rate for JPEG transfer. Increase the value when you prefer to  
get finer image quality, otherwise decrease the value for smaller data size.  
Note.  
Image quality may deteriorate due to scanning with JPEG compression.  
When JPEG compression is enabled, lengths and widths of images may slightly  
be different from that of the scans without JPEG compression.  
This function may not be available for some image scanner models.  
51  
 
4.8. Setting Advance Options  
The "advance dialog" is used to set items related to image processing. The settings apply to  
device-specific functions and items that differ according to whether the scanner used supports  
them.  
The advance option specification is divided into "Color Variance", "Image Processing", and  
"Auto Binary".  
The supported options depend on the scanner. See "Relevant Image Scanner Specification" in  
the Appendix. (  
is displayed for options that cannot be used.)  
The option dialog for this driver is explained below.  
The commonly used buttons are explained first.  
[Default]  
Returns the setting to the initial value.  
[OK]  
Makes the new setting valid and closes the “Advance” dialog box.  
[Cancel]  
Makes the new setting invalid, returns the setting to the previous value, and terminates  
processing.  
[Help]  
Displays online help.  
52  
 
The options are described below:  
4.8.1. Gray  
Figure Advance dialog (Gray)  
Gamma Pattern  
This option corrects distortions from nonlinear image representation. Scanner sensors are  
generally designed to generate output linear to the density of the light reflected from the  
document. However, most output terminals do not produce output that has the desired linear  
relation to the input, and the resulting distortion must be corrected.  
One of the following can be selected as a correction pattern: "Normal", "Soft", "Sharp",  
"Download Pattern", or "Custom".  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
When "Download Pattern" is selected, the above dialog box opens.  
53  
 
Select the gamma pattern download file to be used from the list of file names. Then, press  
the [OK] button. Correction will then be executed using the selected gamma pattern.  
If the gamma pattern download file has not been registered in the list of file names, use the  
[Add] button to register the file.  
See "Download Pattern File" for information about how to specify the file.  
When "Custom" is selected, a custom specification can be entered.  
Entering an arbitrary value between 0.1 and 10.0 enables a gamma pattern corresponding to  
the entered value to be specified.  
White Level Follower  
Select this option to scan a document whose background color is not white, such as a  
newspaper.  
Select "Auto", "Enable", or "Disable".  
When "Enable" is selected, the document is scanned using background follow-up (for line  
drawings). When "Disable" is selected, the document is scanned using the standard basic  
white background (for photographs). When "Auto" is selected, the option automatically  
switches to the optimal setting based on the specified "Image Mode".  
"White Level Follower" is used to adjust the density of the white background of a document  
and correct variations in the background color by compensating the pixels of scanned images  
individually.  
For ordinary use, set "White Level Follower" to off. Use of "White Level Follower" often  
increases the background noise because IPC-3/3D is very sensitive.  
This option is not available if "Gray Scale" is selected for "Image Mode".  
In addition, some scanner models do not support this option. See "Relevant Image Scanner  
Specification" in the Appendix.  
Dropout Color  
You can scan images by removing one of the primary colors (green, red, or blue), which you  
select. This is useful, for example, when you scan black letters with red outlines and you  
want only the black part of the letters to be scanned.  
When "White" is selected, no color dropout occurs but it may be some loss of light yellow  
color.  
When "None" is selected, no color dropout occurs but scanning may slow down depending  
on the compatibility of your PC’s operating environment.  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
54  
Reverse  
This option specifies whether to reverse the black and white of a scanned image.  
If this option is selected, black and white are reversed by reversing the black and white  
pixels. If this option is not selected, the black and white values of the reproduced image  
correspond to the original image.  
Some applications do not permit normal operation. If this occurs, contact the manufacturer  
of the application.  
55  
4.8.2. Image Filter  
Figure Advance dialog (Image Filter)  
Edge Processing  
This option specifies the sharpness of a scanned image.  
Select "None", "Edge Extract", or "Smoothing (Background Removal)".  
None  
Edge processing is not performed.  
Edge Extract  
This option outputs an image with the edge extracted.  
If this option is selected, the boundary between the black part and white part in a closed  
area is traced and the edge extracted.  
"DTC Variance" and "Edge Extract" are mutually exclusive.  
Smoothing (Background Removal)  
This option specifies whether to smooth the curves in an image by removing zigzag lines.  
"Smoothing" or "Emphasis" can be selected. In addition, "Edge Extract" and  
"Emphasis" are mutually exclusive.  
56  
 
Emphasis  
This option outputs an image with the edge emphasized.  
"Emphasis High", "Emphasis Mid", or "Emphasis Low" can be selected.  
If "Emphasis High" is selected, the image becomes sharper. If "Emphasis Low" is  
selected, the image appears less distinct.  
Mirror  
This option specifies whether to flip the scanned image over the scanning axis.  
If this option is selected, a mirror image of the original image is obtained.  
Variance (DTC Variance)  
This option specifies the value for adjusting the dynamic threshold of an image based on the  
brightness of the image.  
A value is specified using the slider. The smaller the value, the lower the variance becomes.  
The higher the value, the higher the variance becomes. To specify the value, drag the tab of  
the slider to the desired setting position. The current setting is displayed on the right. This  
option is mainly used for optical character recognition (OCR). It enables dark and bright  
images in a document to be scanned effectively.  
Floating Slice Level (SDTC)  
Specifies the level of the binary processing done by the floating slice.  
Set the level to higher when scanning documents with dark colored background.  
* This is displayed only when the SDTC mode (Floating Slice) is specified.  
57  
4.8.3 DTC  
This option is valid only when "DTC Variance" is set.  
Figure Advance dialog (DTC Mode)  
Scan mode  
This option selects one of the following two scan modes:  
[for OCR]: This mode is for text recognition applications where irregularity in the image is  
undesirable.  
[for Image]: This mode is for image scanning applications that scan images without prior  
smoothing.  
The specification changes the specifiable items and members for "Threshold Curve" and  
"Gamma Curve".  
The selection screens for "for OCR" and "for Image" are not displayed if IPC-3/3D and IPC-  
4D are installed.  
58  
 
Threshold Curve  
This option specifies the relationship between the threshold value and the maximum density.  
The specification method depends on the [Scan mode] setting.  
In [for OCR] mode, use the scroll bar to set the inclination and density level between 0 and 5.  
Click the arrow of the scroll bar or drag the scroll marker to the desired setting position. The  
current setting is displayed in the center (figure on the left).  
In [for Image] mode, select [Normal] or [Light] (figure on the right).  
If IPC-3/3D and IPC-4D have been installed, there is no difference between [for OCR] and  
[for Image]. The scroll bar is used to set the inclination and density level between 0 and 7.  
(The figure on the right is not displayed.)  
Gamma Curve  
This option specifies the gamma correction curve pattern.  
The available choices depend on the [Scan mode] setting.  
In [for OCR] mode, select [OCR1] or [OCR2].  
In [for Image] mode, select [Dark Image] or [Even].  
For IPC-3/3D and IPC-4D, the gamma curve need not be specified because the contrast is  
adjusted automatically. ([Gamma Curve] is not displayed.)  
Equal to White  
At conversion to binary, this option specifies whether to set the data to black or white when  
the threshold value and the value of the scanned data are equal.  
This option is not available for IPC-4D.  
Ball-Point Pen Mode  
When an image made with a pencil or ball-point pen is scanned, the light reflected from the  
pencil lead or ink is not uniform. As a result, part of the image may be missing. If the [Ball-  
Point Pen] checkbox is checked, filtering is applied to offset the bright area in the document  
and compensate for disconnected or faint lines.  
59  
OCR Smoothing/ Background Removal  
The OCR smoothing is the function to make smooth the notched part of line-drawing, and  
the Background Removal is the function to remove the uneven background.  
These functions are enabled when it is selected.  
For further information, please refer to the User’s guide attached to the IPC board since the  
function to be operated is different by the type of IPC.  
At IPC-3/3D, [Noise Removal] and [OCR smoothing/ Background removal] is enabled  
exclusively.  
Noise Removal  
This option automatically removes spots that appear as black stains in a white area and spots  
that appear as white stains in a black area.  
This option uses an algorithm that removes particles from 2 x 2 to 5 x 5 dot matrixes. The  
size of one dot depends on the resolution setting, and is equivalent to 1/400 inch for 400 dpi.  
Particles are distinguished from the text by whether they are connected to other dots within  
the specified number of pixels.  
At IPC-3/3D, [Noise Removal] and [OCR smoothing/ Background removal] is enabled  
exclusively.  
Figure Advance dialog (DTC Mode) <IPC-3/3D and IPC-4D installed>  
60  
4.8.4. When Color (/Grayscale) is specified  
For color scanners, when “Color” is selected in the [Image Mode], the [Advance] dialog  
changes as follows. And in case of some color scanners, when selecting “Grayscale” the  
[Advance] dialog change as same as selecting “Color”.  
There are two image samples which are “Sample (before processing)” and “After (after  
processing)” on this dialog. When you change a setting item, the effect of the setting item is  
reflected in the image “After”.  
You can specify the items, checking their effect.  
<Image Mode : Color selected>  
<Image Mode : Grayscale selected>  
Figure Advance dialog (Color / Grayscale)  
Shadow/Highlight (Color / Grayscale)  
Shadow : The highlight allows the darkest part of the document to be controlled.  
The higher the shadow value, the darker the image.  
Highlight : The highlight allows the brightest part of the document to be controlled.  
The higher the highlight value, the lighter the image.  
Any levels on the document outside these settings are flooded (all 0 or 255), while the  
interval between the shadow and highlight settings are equally divided into 255 levels,  
which are used to create the output images. This means that if the shadow and highlight  
settings are close to each other, the contrast for that interval in the scanned document will be  
very strong (but with all other areas maximizing high or low).  
61  
 
Contrast/Brightness (Color / Grayscale)  
Contrast :  
Sets the contrast of light and shadow in a scanned image. Specify the contrast  
with a number in the range of 1 (low [soft]) to 255 (high [sharp]).  
If this value is increased, the dark part of the image is shown darker and the  
light part is shown lighter.  
Some scanner models do not support this function. See "Relevant Image  
Scanner Specification" in Appendix.  
Brightness : Sets the brightness of the overall image. Specify the brightness with a number  
in the range of 1 (light) to 255 (dark). To darken the overall image, increase  
the value of the setting. To brighten the overall image, decrease the value.  
Gamma (Color / Grayscale)  
This option corrects distortions from nonlinear image representation. Scanner sensors are  
generally designed to generate output linear to the density of the light reflected from the  
document. However, most output terminals do not produce output that has the desired linear  
relation to the input, and the resulting distortion must be corrected.  
An arbitrary range is between 0.1 and 10.0.  
Preset Gamma (Grayscale only)  
This option corrects distortions from nonlinear image representation. Scanner sensors are  
generally designed to generate output linear to the density of the light reflected from the  
document. However, most output terminals do not produce output that has the desired linear  
relation to the input, and the resulting distortion must be corrected.  
One of the following can be selected as a correction pattern: "Normal", "Soft", "Sharp",  
"Download Pattern", or "Custom".  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
When "Download Pattern" is selected, the above dialog box opens.  
62  
Select the gamma pattern download file to be used from the list of file names. Then, press  
the [OK] button. Correction will then be executed using the selected gamma pattern.  
If the gamma pattern download file has not been registered in the list of file names, use the  
[Add] button to register the file.  
See "Download Pattern File" for information about how to specify the file.  
When "Custom" is selected, you can specify the values on the [Shadow/Highlight],  
[Contrast/Brightness] and [Gamma] tab.  
Color select (Color only)  
It is possible to select independent value on each color  
sRGB Output (Color / Grayscale)  
Scans images by using the color control information of “Color Space Profile.icm” (the  
standard color profile of Windows).  
* Refer to “Windows Help” to learn more about “color profile”.  
<Image Mode : Color selected>  
<Image Mode : Grayscale selected>  
Figure Advance dialog ([Quality] / [Gray] tab)  
63  
Image Emphasis (Color only)  
This option specifies the sharpness of a scanned image.  
Select "None", "De-Screen" or "Emphasis".  
None  
Edge processing is not performed.  
Emphasis  
This option outputs an image with the edge emphasized.  
"Emphasis High", "Emphasis Mid", or "Emphasis Low" can be selected.  
If "Emphasis High" is selected, the image becomes sharper. If "Emphasis Low" is  
selected, the image appears less distinct.  
De-Screen  
"De-Screen Level 1", "De-Screen Level 2", "De-Screen Level 3", or "De-Screen Level  
4" can be selected.  
This option eliminates moirés patterns. To eliminate more effectively, higher level is  
selected.  
White Level Follower (Color)  
Select this option to scan a document whose background color is not white, such as a  
newspaper.  
Select "Auto", "Enable", or "Disable".  
When "Enable" is selected, the document is scanned using background follow-up (for line  
drawings). When "Disable" is selected, the document is scanned using the standard basic  
white background (for photographs). When "Auto" is selected, the option automatically  
switches to the optimal setting based on the specified "Image Mode".  
"White Level Follower" is used to adjust the density of the white background of a document  
and correct variations in the background color by compensating the pixels of scanned images  
individually.  
Some scanner models do not support this function. Refer to "Relevant Image Scanner  
Specification" in Appendix.  
Reverse (Color / Grayscale)  
This option specifies whether to reverse the black and white of a scanned image.  
If this option is selected, color data is reversed. If this option is not selected, the color values  
of the reproduced image correspond to the original image.  
64  
Some applications do not permit normal operation. If this occurs, contact the manufacturer  
of the application.  
Some scanner models do not support this function. Refer to "Relevant Image Scanner  
Specification" in Appendix.  
Dropout Color (Grayscale only)  
You can scan images by removing one of the primary colors (green, red, or blue), which you  
select. This is useful, for example, when you scan black letters with red outlines and you  
want only the black part of the letters to be scanned.  
When "White" is selected, no color dropout occurs but it may be some loss of light yellow  
color.  
When "None" is selected, no color dropout occurs but scanning may slow down depending  
on the compatibility of your PC’s operating environment.  
Some scanner models do not support this function. See "Relevant Image Scanner  
Specification" in Appendix.  
65  
4.9. Setting the Setting Manager Options  
These options are used to manage the setting files, and switch the basic scan dialog display.  
Click the [Config...] button of the main dialog to open the [Configuration] dialog box shown  
below.  
Figure Configuration dialog box  
Setting Files  
The setting information of the scan conditions can be saved in a “Setting file.”  
Scan condition settings that have been set in advance in this dialog can be selected from the  
list of setting files. This enables selection of all settings at the same time without having to  
enter the scan conditions one at a time. Press the  
button to open the list of setting files.  
Subsequent scanning operations can be performed effectively by registering several types of  
scan conditions that are frequently used.  
66  
 
FTS File Information  
The information of the setting file selected in [Setting Files] is displayed.  
[Show this dialog next open] checkbox  
If this checkbox is checked, [Basic Scan Dialog] will be activated the next time the driver is  
activated.  
[OK] button  
Makes the new setting valid, closes this dialog box, and returns to the main dialog.  
[Add] button  
Adds the setting of the current driver to a setting file.  
Pressing the [Add] button opens the [File addition] dialog.  
Enter the [Description] and [Filename] as shown in the example above. Then, press the  
[OK] button to add the new setting file. To cancel, press the [Cancel] button.  
Description: Enter a character string to be displayed in the selection frame of the [Setting  
Files].  
Filename:  
Specify the name of the file used to save the settings.  
67  
[Delete] button  
Deletes unnecessary setting files.  
Select the setting file to be deleted and then press the [Delete] button. A confirmation dialog  
will be displayed. Press the [OK] button to delete the setting file. To cancel, press the  
[Cancel] button.  
[Help] button  
Displays online help.  
[Initialization] button  
All of scan settings are returned to the initial value.  
68  
4.10. Basic Scan Dialog  
The basic scan dialog contains only the minimum functions required for scanning. The detailed  
setting functions of the main dialog have been omitted.  
Scanning can be easily performed by selecting a registered setting file.  
The basic scan dialog is also useful for avoiding incorrect operations when standard work is  
performed.  
By checking the [Show this dialog next open] checkbox of the [Configuration] dialog, the Basic  
Scan dialog will be opened instead of the main dialog box at the next activation.  
<Scan Procedure>  
1. Select the file to be used from the list of setting files.  
2. Click the [Scan] button.  
Scanning is performed based on the settings of the setting file information.  
<Configuration>  
Setting Files  
A list of setting files is displayed. When the desired file is selected, the setting information  
saved in the file will be read and reflected during scanning.  
69  
 
FTS File Information  
The contents of the selected file are displayed.  
[Scan] button  
Executes scanning based on the contents of the setting file.  
[OK] button  
Terminates without performing the scan operation.  
[Adjust] button  
Switches from the basic scan dialog to the main dialog.  
[Help] button  
Displays online help.  
[Show this dialog next open] checkbox  
If this checkbox is checked, the [Basic Scan Dialog] will be opened at the next startup. If  
this checkbox is not checked, the main dialog will be opened at the next startup.  
70  
4.11. Download Pattern File  
The "download pattern file" of this driver is a file that defines the patterns to be used by the  
scanner to execute various image processing. This file is available in the following two versions.  
Each version can be selected using the [Download Selection Dialog] that opens when  
[Download] is selected.  
The file is a text file that conforms to the following rules. Use an appropriate text editing  
program (for example, "Note Pad" in the operating system) to edit the file.  
Dithered download pattern file  
Any user defined dithered pattern can be used to scan an image by downloading the pattern  
from the dithered download file to the scanner. The defined pattern becomes effective when  
[Download Pattern] is selected for [Halftone].  
Some models do not support this file. See "Relevant Image Scanner Specification" in  
Appendix.  
Although the standard extension of the file name is ".DTH," there may be exceptions.  
Coding configuration:  
(n, size in the X direction),(m, size in the Y direction),  
(pattern value for the X1/Y1 coordinates),  
(pattern value for the X1/Y2 coordinates),  
(pattern value for the X1/Y2 coordinates),........  
(pattern value for the Xn/Ym-2 coordinates),  
(pattern value for the Xn/Ym-1 coordinates),  
(pattern value for the Xn/Ym coordinates)  
Meaning of each element:  
(n, size in the X direction) indicates the size of the matrix in the X direction. Specify 8  
for the scanner supported by this driver.1  
(m, size in the Y direction) indicates the size of the matrix in the Y direction. Specify 8  
for the scanner supported by this driver.1  
(Pattern value for the Xx/Yy coordinates) contains a values in the range of 0 (bright) to  
255 (dark) that specifies the brightness of the X coordinate, x, and the Y coordinate, y.  
Note  
Use a delimiter other than a number to delimit elements. For most cases, use a comma  
(,).  
1 In case of fi-5650C, fi-5750C, you can specify the value from 1 to 32.  
71  
   
Example: In case of 8x8 matrix  
8, 8,  
128, 128, 128, 128, 128, 128, 128, 128,  
255, 128, 128, 128, 128, 128, 128, 128,  
255, 255, 128, 128, 128, 128, 128, 128,  
255, 255, 255, 128, 128, 128, 128, 128,  
255, 255, 255, 255, 128, 128, 128, 128,  
255, 255, 255, 255, 255, 128, 128, 128,  
255, 255, 255, 255, 255, 255, 128, 128,  
255, 255, 255, 255, 255, 255, 255, 128,  
8 elements  
8 elements  
72  
Gamma download pattern file  
Any user defined gamma correction processing can be performed by downloading the  
pattern from the gamma download file to the scanner. The defined pattern becomes  
effective when [Download Pattern] is selected for [Gamma Pattern].  
Some models do not support this file. See "Relevant Image Scanner Specification" in  
Appendix.  
Although the standard extension of the file name is ".GMA," there may be exceptions  
Creation of a gamma download pattern file can be facilitated using the following utilities for  
editing the gamma correction pattern:  
Coding configuration:  
(gray-scale in the X direction),(gray-scale in the Y direction),  
(X0 output value),(X1 output value),(X2 output value),........  
(X253 output value),(X254 output value),(X255 output value)  
Meaning of each element:  
(gray-scale in the X direction) indicates the size and the gray scale of the input value.  
(In this driver, this value is fixed at 256.)  
(gray-scale in the Y direction) indicates the size and the gray scale of the output value.  
(In this driver, this value is fixed at 256.)  
(Xx output value) indicates the output value, in the range of 0 (bright) to 255 (dark), for  
an input value x.  
Note  
Use a delimiter other than a number to delimit elements. For most cases, use a comma (,).  
73  
Example  
256, 256,  
255, 254, 253, 252, 251, 250, 249, 248, 247, 246, 245, 244, 243,  
242, 241, 240, 239, 238, 237, 236, 235, 234, 233, 232, 231, 230,  
229, 228, 227, 226, 225, 224, 223, 222, 221, 220, 219, 218, 217,  
216, 215, 214, 213, 212, 211, 210, 209, 208, 207, 206, 205, 204,  
203, 202, 201, 200, 199, 198, 197, 196, 195, 194, 193, 192, 191,  
190, 189, 188, 187, 186, 185, 184, 183, 182, 181, 180, 179, 178,  
177, 176, 175, 174, 173, 172, 171, 170, 169, 168, 167, 166, 165,  
164, 163, 162, 161, 160, 159, 158, 157, 156, 155, 154, 153, 152,  
151, 150, 149, 148, 147, 146, 145, 144, 143, 142, 141, 140, 139,  
138, 137, 136, 135, 134, 133, 132, 131, 130, 129, 128, 127, 126,  
125, 124, 123, 122, 121, 120, 119, 118, 117, 116, 115, 114, 113,  
112, 111, 110, 109, 108, 107, 106, 105, 104, 103, 102, 101, 100,  
99, 98, 97, 96, 95, 94, 93, 92, 91, 90, 89, 88, 87, 86, 85, 84,  
83, 82, 81, 80, 79, 78, 77, 76, 75, 74, 73, 72, 71, 70, 69, 68,  
67, 66, 65, 64, 63, 62, 61, 60, 59, 58, 57, 56, 55, 54, 53, 52,  
51, 50, 49, 48, 47, 46, 45, 44, 43, 42, 41, 40, 39, 38, 37, 36,  
35, 34, 33, 32, 31, 30, 29, 28, 27, 26, 25, 24, 23, 22, 21, 20,  
19, 18, 17, 16, 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0  
74  
5. Using the Gamma Pattern Editor  
5.1. Start-up  
Click on [Start] and select [Gamma Pattern Editor] from "Scanner Utility for Microsoft  
Windows" under [Programs]. The following menu is displayed:  
Figure Gamma Pattern Editor Tool start-up menu  
75  
   
5.2. [File] menu  
[Load...]  
This menu is used to read the Gamma Download file and display the graph and gradations.  
The name of the open file is displayed above the graph area.  
[Save]  
The gamma pattern currently being edited is saved in the file whose name is displayed above  
the graph area. If no filename is displayed, the pattern is named and saved in that file.  
[Save As...]  
The gamma pattern currently being edited is named and saved in that file. The saved  
filename is then displayed above the graph area.  
[Close]  
Select this to exit the editing program.  
5.3. [Help] menu  
[About]  
Information related to this editor and its version number is displayed.  
76  
   
5.4. Gamma Pattern Editing  
Graph Area  
The graph area is a 256-dot x 256-dot white square area bordered by black lines, where the  
relationship between the input values of 0 to 255 (x axis) and output values of 0 to 255 (y  
axis) is indicated in blue lines. Each graph dot represents one division (unit).  
Gradation  
The input is displayed in black and white in 256 single-dot steps from 0 at the left border to  
255 at the right border. The gamma function of the scanner is displayed. After saving it, the  
displayed (gray scale) gamma function is fixed and constant. The output values are  
displayed in single dots in relation to the input values and the brightness of the output  
equipment is displayed. To ensure accurate display, the display must be set for "True-Color"  
or greater.  
Gamma  
Calculation of the output values is based on the value γ entered in the edit box; the graph and  
the gradation are then displayed. The values that can be input are integers greater than 0 or  
fractions.  
<<Formula>> Output = (input ÷ 255)γ x 255 (Input = 0 - 255)  
Free Edit  
Designates whether to enable editing of the graph area directly using the mouse cursor.  
If this box is checked, the gamma pattern input edit box cannot be used and only editing  
using the mouse cursor is supported.  
Smooth  
Designates whether to smooth edited curves. This setting is only valid when Free Edit is  
selected. In this setting, the curved lines drawn by the mouse are automatically smoothed.  
This is reflected in the graph and gradation display.  
Reverse  
Designates whether to reverse black and white. When this box is checked, the current output  
values are converted to (255 - output values).  
77  
 
6. How to Use the FUJITSU Scanner Control Center  
6.1. Outline  
This software that is resident in the system continuously monitors the scanner connected and  
starts the target application in response to an instruction from the operation panel in the scanner.  
(Pressing the start button on the scanner starts the application that has been set in advance.)  
And by using this software, you can replace consumables and adjust offset of the connected  
scanner.  
For applicable models, see "Relevant Image Scanner Specification" in the Appendix.  
6.2. How to Start the FUJITSU Scanner Control Center  
Select as follows: [Start] - [Program] - [Scanner Utility for Microsoft Windows], then  
[FUJITSU Scanner Control Center]  
If this application is started, it is stationed in the system, and then an icon is displayed on the task  
tray.  
An icon indication changes to show how the scanner is connected as follows:  
1. The scanner can be used:  
2. The scanner power is turned off and not connected:  
Right-clicking the icon displays the following pop-up menu.  
Left-clicking the icon displays the scanner being connected as shown below.  
The scanner that has been monitored by this application is indicated with a check mark.  
78  
     
6.3. Pop-up Menu  
[Scan]  
Start the application which is selected on [Common] tab of [Option].  
[Rescan Scanner]  
Rescans the scanner that is currently connected.  
A scanner that is not recognized by the OS cannot be found even though it is rescanned.  
[Option]  
You can set up the following items.  
Settings of the application to be started when the [Start] or  
[Common]  
[Scan] button of the scanner is pressed  
Diagnosis of the selected scanner  
[Diagnosis]  
Indication of the functional information of the selected  
[Device info]  
scanner  
Replacement of the consumables, Setting of the power  
[Device setting]  
management, Adjustment of the offset and magnificent  
[Select Scanner]  
When multiple scanners are connected, select a scanner to be monitored.  
With this application, only one scanner can be monitored at a time. If multiple scanners are  
connected, scanner switching is required to monitor the individual scanners.  
Select a scanner to be monitored in the list of scanners to be connected. (The list is given  
below.)  
Left-clicking the task tray icon displays connected scanner names on the pop-up menu. It is  
also possible to select a scanner on this menu.  
79  
 
[Help]  
Displays help information concerning to this application.  
[About]  
Displays version information concerning to this application.  
[Exit]  
Terminates this application.  
80  
6.4. Option  
6.4.1. [Common] tab  
Sets up the application to be started when the [Start] or [Scan] button of the scanner is  
pressed.  
[Path]  
Specifies a file name of the application to be started with its absolute pathname.  
A file can be also selected directly by using the […] button.  
[Argument]  
Specifies an argument to be passed when starting the specified application. (This item can  
be omitted.)  
[Start in]  
Specifies a default folder for starting the application.  
A default folder can be also selected by using the […] button.  
(This parameter can be omitted.)  
[Run]  
Specifies the display size of the application to be started.  
81  
   
[Use Plug-In]  
Checking this check box specifies a plug-in.  
(A plug-in is an additional program for adding a new function to the application.)  
[Setting]  
Sets a plug-in in accordance with the following procedure:  
Pressing the [Setting] button after selecting a target plug-in name in the plug-in list  
displayed displays the plug-in setting screen.  
Pressing the [OK] button after setting each item reflects the settings for the  
application to be started.  
[Install]  
A new plug-in can be installed.  
Press the [Install] button and specify a file of the plug-in to be installed. A new plug-in is  
registered in the list.  
* Up to 50 plug-ins can be registered.  
82  
<<Setting the Start button>> (* for fi-4990 / M4099D)  
If the scanner being monitored has function keys (F1,F2,...), it is necessary to assign a  
function key to the start button in advance.  
If no function key has been assigned to the start button, a dialog box for determining whether to  
set the start button is displayed when the dialog box is displayed after selecting [Option] on the  
pop-up menu.  
Selecting "Yes" displays a dialog box below.  
(If "No" is selected, the function to start any application when the start button in this application  
is pressed is disabled.)  
Pressing the [OK] button after selecting one of function keys from F1 to F3 enables assigning a  
function key to the start button. If the [Cancel] button is pressed, the function key is not  
assigned to the start button.  
(If the [Cancel] button is pressed, the function to start any application when the start button in  
this application is pressed is disabled.)  
83  
6.4.2. [Diagnosis] tab  
Diagnoses the selected scanner’s statement, and reports the result.  
[Diagnose] button  
Starts diagnosing when clicking this button.  
Report  
The result of diagnosis is displayed.  
* Depending on the scanner model, this tab may not be displayed.  
84  
 
6.4.3. [Device info] tab  
A list of the functions compatible with the selected scanner driver is displayed. The items  
displayed depend on the selected model of scanner. Only hardware functions are displayed.  
The functions realized by software are not displayed in this tab folder. Therefore, the  
displayed content may not match the content specified during reading. The contents of this  
tab folder are not displayed if the scanner driver is either currently in use or not connected to  
the computer. If they are not displayed, stop the application being used by the scanner driver  
or check the connection. Then, select this tab folder again to display the contents.  
85  
 
6.4.4. [Device Setting] tab  
Information related to the operation and maintenance of the scanner driver can be displayed  
and set up. For some scanner models, this tab may not be displayed, or some items cannot  
be set up (grayed out). Changing the setup activates the Apply button. The changed setup is  
reflected on the device only if the [Apply] button or [OK] button is clicked. The contents of  
this tab folder are not displayed if the scanner driver is either currently in use or not  
connected to the computer. If they are not displayed, stop the application being used by the  
scanner driver or check the connection. Then, select this tab folder again to display the data.  
About how to replace consumables  
When [Scanner Information] tab is selected, the following dialog appears.  
An equivalent count of the pages scan after consumables are replaced and remaining the  
imprinter ink are also displayed in the part of the red frame in the figure. To reset the  
consumables counter after replacing consumables, click the [Clear] button. Depending on  
the device, this operation can be executed using the operation panel of the device. Displayed  
consumables names or item numbers also vary depending on the device. For information,  
see the operator’s guide of the scanner.  
86  
 
Note.  
Depend on some scanner models, once the [Scanner Information] tab appears, the  
operation panel is unable to be handled. In this case, close this dialog and turn the power  
ON/OFF of the scanner. After the scanner setup, the operation panel is able to be handled.  
When using a scanner, the following message may be displayed.  
If this message appears, replace consumables following the instructions below.  
< If replacing consumables immediately >  
1. Check [This message not display again.]  
2. In cases where consumables are replaced after completing all documents being scanned,  
click [Ignore]. In cases where scanning is stopped for an immediate replacement, click  
[Cancel].  
3. Following the operator’s guide of the device, replace the consumables.  
4. Select [Device setting] tab, click [Clear] button to reset the consumables counter.  
< If replacing later (immediate replacement is impossible) >  
1. If it is not necessary to display this message again, check [This message not display  
again]*. If it is necessary to display this message again after scanning xxx pages, check  
[Warns again after scanning xxx pages].  
2. If the scanning is continued, click [Ignore] and close the message. If the scanning is  
stopped, click [Cancel] and close the message.  
3. Replace consumables as soon as possible or when this message appears next time.  
4. After the replacement, click [Clear] of [Device setting] tab.  
(* If [This message not display again] is checked, this message will not appear before the  
consumable counter is reset.)  
About Power saving  
Specify when the lamp turns off. This is the elapsed time after a scan is complete.  
* Depending on the scanner model, the range which can be set is different.  
87  
About [Multifeed] Button  
Use this to specify multifeed detection area.  
By default Multifeed Detection monitors paper overlap over the central column (width:  
35mm) of the document to be scanned. This will lead to mis-detection when the document is  
partially pasted with photographs or clippings.  
When scanning these kinds of documents, you can specify an exact detection area to prevent  
mis-detection.  
Click on the button and the following screen will appear.  
Enable (Detection Area Selection)  
Vertically select an area where multifeed detection will or will not be conducted.  
Choose either “Select area for applying Multifeed Detection” or “Select area for not  
applying Multifeed Detction”.  
Select area for applying Multifeed Detection  
Select an area for multifeed detection.  
Select area for not applying Multifeed Detection  
Select an area not to be detected.  
Start  
Set start position as distance from the document’s top edge.  
(Possible values: 0 - 510mm with Start Position < End Position)  
End  
Set end position as distance from the document’s top edge.  
(Possible values: 0 - 510mm with Start Position < End Position)  
* This button may not be displayed for some scanner models.  
88  
About [Power Control] Button  
Enable/Disable the scanner’s power switch.  
Enable Power Switch  
Scanner power switch is enabled.  
The scanner can be turned ON/OFF by the power button.  
Disable Power Switch  
Scanner power switch is disabled.  
The scanner will be turned ON/OFF by connecting/disconnecting the power supply.  
(Power button will no longer work).  
* If the scanner is equipped with a main power switch, the main power switch needs  
to be set at “ON”.  
* This button may not be displayed for some scanner models.  
About Adjustment of Offset / Magnification  
When clicking the [Offset] button, the following dialog appears.  
Note  
Depend on some scanner models, once the [Scanner Information] tab appears, the  
operation panel is unable to be handled. In this case, close this dialog and turn the power  
89  
ON/OFF of the scanner. After the scanner setup, the operation panel is able to be handled.  
Using this dialog box, the offset of the leading edge and the magnification for the sub-  
scanning direction can be changed.  
[Offset Setting]  
If the position of the scanned image shifts from the original document, fine adjustment is  
possible.  
At shipment, the offset has been adjusted to an optimum value within a certain range.  
Therefore, adjustment is not generally required.  
*The maximum size of changes depends on the device.  
Enable eliminating a dark area on the top of the image.  
Enable eliminating a dark area on the left side of the image.  
These modes can be selected to eliminate the dark area on the leading edge and the left  
side appeared when using the flat bed  
*These functions may not be displayed for some scanner models.  
[Vertical magnification Adjustment]  
The Vertical magnification correction value of sub-scanning direction can be changed.  
For ADF scanning, the image is expanded or shrunk in the paper feeding direction based on  
the setting value at shipment.  
For FB scanning, the image is expanded or shrunk in the direction to which the scan head  
moves based on the setting value at shipment.  
This function is used to adjust the image whose ratio of length and width seems different  
from the original document.  
*The setting value varies depending upon the device used.  
90  
7. Using the Firmware Updater  
This application software is used to update the firmware installed in the scanner device.  
However, this application software is automatically executed when the driver installation is  
completed. If the software is executed at the installation, it is not necessary to execute again.  
This application software shall be used only for the following devices. Do not use for other  
devices.  
Applicable Devices: fi-4750, M4097D, fi-4750C  
Check items before use.  
Before using this application software, check the following items.  
-
Check that the scanner is connected properly. If more than one scanner are connected,  
the update cannot be done correctly. Connect one scanner only that has the firmware to  
be updated.  
-
If the driver has been activated, close the application software that is using the driver.  
How to use  
Select as follows: [Start] - [Program] - [Scanner Utility for Microsoft Windows], then  
[Firmware Updater]  
The program is executed and the following dialog box appears.  
Press the [Yes] button. The following dialog box is displayed and the firmware update starts.  
* Do not turn off the power of the scanner during the firmware update. Otherwise the device  
may break down.  
91  
 
When the following dialog box appears, press the [OK] button.  
The firmware update has been completed successfully. Reactivate Windows®.  
92  
8. Troubleshooting  
8.1. Error Messages  
8.1.1. Messages from the TWAIN Driver  
• The input value is outside the range.  
Cause:  
A value exceeding the range allowed for an input item was input.  
User response:  
Input a value inside the allowed range. Refer to the input item or the  
image scanner specification for the range.  
• The input value is not acceptable.  
Cause:  
A value exceeding the range allowed for an input item was input.  
User response:  
Input a value inside the allowed range. Refer to [Help] of the item or  
the User's Guide for the correct range.  
• This file cannot be removed because it is specified in other side.  
Cause:  
An attempt was made to remove a file using the dither pattern or  
gamma download pattern file setting dialog. However, the file is  
being used for the other side (front side if back side or back side if  
front side).  
User response:  
Before removing the file, change the setting of the other side and then  
remove.  
• The initial value contains an invalid value. The default standard value is set.  
Cause:  
A value outside the specified range, or invalid text was found in the  
initial-value data file (the specific item involved is indicated by  
Entry=XXXXX). If the file has been modified, the setting value for  
the item may be wrong. If the file has not been rewritten, the file may  
have been damaged.  
User response:  
The value is set to a standard value. Be sure to check the hard disk  
(chkdsk/scandsk) and check for computer viruses regularly.  
• The value is higher than the maximum scanning size. Either the resolution value or  
the scanning area has to be reduced.  
Cause:  
A value exceeding the data capacity of the scanner was specified. As  
the resolution is increased, the amount of data to be scanned also  
increases.  
User response:  
Decrease the resolution or reduce the size of the scan area.  
93  
     
• The value for custom paper is higher than the maximum scan size. Width needs to  
equal 279 mm or less and length needs to equal 420 mm or less.  
• The value for custom paper is higher than the maximum scan size. Width needs to  
equal 11 inch or less and length needs to equal 16.53 inch or less.  
• The value for custom paper is higher than the maximum scan size. Width needs to  
equal xxx pixel or less and length needs to equal xxx pixel or less.  
Cause:  
A value exceeding the limit applicable to the scan area of the scanner  
was specified.  
User response:  
To specify a custom paper size, specify the value that is smaller than  
the value applicable to the device.  
• The value for custom paper is greater than the maximum scan size. Width need to  
less equal 259mm.  
• The value for custom paper is greater than the maximum scan size. Width need to  
less equal 10.24inch.  
• The value for custom paper is greater than the maximum scan size. Width need to  
less equal 2048pixel.  
Cause:  
A value exceeding the limit applicable to the scan area of the scanner  
was specified.  
User response:  
To specify a custom paper size, specify the value that is smaller than  
259mm (10.24inch, 2048pixcel)  
• The resolution must be less or equal to xxx dpi when scanning in Gray Scale.  
• The resolution must be less or equal to xxx dpi when scanning in Color.  
• Cannot specify Long Page Scan. Width need to less equal 400dpi.  
Cause:  
There is a limit on the resolution when gray-scale scanning, long page  
scanning or color scanning is used.  
User response:  
Specify a resolution value that is below the indicated xxx dpi.  
• Cannot specify Gray Scale with Custom resolution.  
• Cannot specify Color with Custom resolution.  
Cause:  
Custom resolution was designated when Gray Scale or Color was  
designated.  
User response:  
Designate a resolution value other than Custom.  
• Cannot specify Gray Scale with duplex document.  
Cause:  
Duplex scanning is specified with Gray Scale specified.  
User response:  
At duplex scanning, select Black/white binary or Half tone for the  
[Image type].  
94  
• Cannot specify Individual Setting with Gray Scale.  
• Cannot specify Long Page Scan with Gray Scale.  
Cause:  
Gray Scale and Individual Setting are specified at the same time.  
Gray Scale and Long Page Scanning are specified at the same time.  
Uncheck Individual Setting when specifying Gray Scale.  
User response:  
At Long Page scanning, select Black/white binary or Half tone for the  
[Image type].  
• Your application using may not support page end detection, or undefined image size  
function.  
Cause:  
Scanned image may not be displayed correctly when scanning by  
using the “page end detection” or “undefined image size” function  
with the application which is not supporting these functions.  
User response:  
When scanned image is not displayed correctly, please select  
“disable” for the [Option]-[Rotation]-[Automatic Size and Skew  
detection].  
• Dither pattern file not found.  
Cause:  
File download has been specified, but a file has not been selected.  
Use the [File…] button to specify a file.  
User response:  
• Gamma pattern file not found.  
Cause:  
File download has been specified, but a file has not been selected.  
Use the [File…] button to specify a file.  
User response:  
• Selected file can not be deleted.  
If the selected setting file is write-protected, it cannot be deleted.  
Use Explorer to delete the file later.  
Cause:  
User response:  
• Description not specified.  
Cause:  
The description of the setting file has not been specified.  
User response: Enter the description of the setting file in the description field. Then,  
try scanning again.  
• Filename not specified.  
Cause:  
The filename of the setting file has not been specified.  
User response:  
Enter the filename of the setting file. Then, try scanning again.  
95  
• Specified string is too long.  
Cause:  
The specified string is too long. Up to 128 en-size characters and up  
to 64 em-size characters can be specified.  
User response:  
User response: Reduce the number of characters in the string so that  
they do not exceed 128 en-size characters. Then, try scanning again.  
• Cannot specify next words for filename. \:;?”<> |.  
Cause:  
The specified filename contains one or more of the following  
characters: \:;?”<> |.  
User response:  
Enter a file name that does not contain the above characters. Then,  
make the settings again.  
• The image scanner not found.  
• An abnormality has occurred during communication. Make sure that the power is on,  
and that the cable is firmly connected.  
• Communication failed. Make sure that the power is on, the cable is firmly connected,  
and the scanner is not used by another application.  
• An abnormality has occurred during communication.  
Cause:  
Possible causes include the following: an image scanner that is not  
supported by this driver has been connected, no image scanner has  
been connected, or the cable is not connected.  
Otherwise, the initial values of the image scanner were overwritten  
while the driver was open.  
User response:  
Check the connection of the image scanner.  
Check the scanner is not used by other application.  
• The specified image scanner is being used.  
Cause:  
The image scanner may be already in use by another application, or  
the TWAIN driver may have been started twice.  
User response:  
User response: After all applications are terminated, restart the image  
scanner for scanning.  
• An input-output error occurred in the image scanner.  
Cause:  
A fault occurred during the scan operation of the image scanner.  
There may be a fault in the image scanner itself.  
User response:  
Turn off the power of all devices, then turn on the power of the  
computer before turning on the scanner and retry scanning. If the  
error still occurs, contact the retail store where the image scanner was  
purchased, or the nearest service center.  
96  
• Scanner is turned OFF. Data source processing is closed. Turn ON the scanner and  
re-scan.  
Cause:  
Scanner may be turned OFF during scanner use.  
User response:  
Turn ON the scanner and re-scan. If the error persists, reboot the PC.  
• Paper jammed in the ADF  
Cause:  
A paper jam occurred in the device.  
User response:  
Turn off the power of the device, then remove the paper from inside  
the device. Removing the paper by using excessive force will result  
in device failure, so be careful.  
When the paper jam occurs repeatedly, clean inside of the scanner.  
• The ADF is open. Close the ADF and set the document on ADF paper chute or  
Hopper.  
Cause:  
The ADF cover is open.  
User response:  
Close the ADF cover, and set the document on ADF paper chute or  
Hopper.  
• No paper on ADF paper chute or Hopper.  
Although ADF was selected as the paper feeding method, no paper is  
found on ADF paper chute or Hopper.  
Cause:  
Select another paper feeding method or set the document on ADF  
paper chute or Hopper.  
User response:  
• The ADF is open, or No paper on ADF paper chute or Hopper.  
Cause:  
The ADF cover is open, or there is no paper on ADF paper chute or  
Hopper.  
User response:  
Close the ADF cover, or load paper.  
• Insufficient buffer memory size of scanner device for current scanning parameters.  
Please reduce the scanning area or the resolution, or install additional memory in the  
scanner.  
Cause:  
A memory option has not been installed in the image scanner.  
Otherwise, a large area or resolution that is not supported by the  
image scanner has been specified.  
The memory inside the scanner may be insufficient due to the  
excessive data size of the scanning image.  
User response:  
Reduce the scanning area or resolution. Otherwise, install the  
memory option. Refer to the User's Guide of the image scanner for  
more information.  
In color scanning, try to increase the data compression ratio.  
97  
• The current parameter(s) is (are) not allowed. Please use (an)other parameter(s)  
and try scanning again.  
Cause:  
An incorrect value has been specified for the image scanner. The  
problem may be due to an illegal combination with the specification  
value from the application.  
User response:  
Change the specification values. Then, try scanning again.  
• Irregular status is detected in scanner..  
Cause:  
A scanner fault such as a blown fuse or foreign matter in the scanning  
section has occurred.  
User response:  
Restart the scanner.  
Confirm the cable connection.  
Clean inside of the scanner.  
If the error persists, contact the retail store where the image scanner  
was purchased or the nearest maintenance and service center.  
• Anomaly in the command for communicating with the scanner.  
• Anomaly in communication with the scanner.  
Cause:  
The SCSI cable is not connected firmly or is disconnected.  
User response:  
Confirm the cable connection.  
If the cable is disconnected, replace the cable with new one.  
If the error persists, contact the retail store where the image scanner  
was purchased or the nearest maintenance and service center.  
• Hardware Error was detected. Carrier motor/sensor was broken or Shipping Lock is  
set in "Lock" position. Please refer to the user's manual for your scanner.  
• Please confirm the shipping lock is unlocked.  
Cause:  
The Shipping Lock may not be set in "Unlock" position.  
User response:  
Check the Shipping Lock.  
If the Shipping Lock is set in "Lock" position, set the Shipping Lock  
in "Unlock" position referring to the user's manual for your scanner.  
• Ink cartridge is not installed in the imprinter properly. Please check the installation  
and try again.  
Cause:  
The imprinter (Endorser) has no ink cartridge or the ink cartridge may  
be mounted improperly.  
User response:  
Check that the ink cartridge of the imprinter is mounted properly and  
scan again.  
• Imprinting position is set out of paper. Please check the imprinting position and try  
again.  
98  
Cause:  
Printing is not available because the printing part is outside the paper  
width.  
User response:  
Adjust the imprinter so that the printing part is settled within the paper  
width.  
• A Hardware Alarm is detected in the Imprinter or Endorser option.  
Cause:  
Failure on Imprinter or Endorser.  
Please check if the Imprinter or the Endorser is installed completely.  
User response:  
If the error occurs after checking the Imprinter or the Endorser, please  
contact the retail store where the product was purchased or the nearest  
service center.  
• The Multifeed is detected.  
Cause:  
The papers are scanned with multifeeding. (One paper stuck to  
another)  
User response:  
Remove the papers stopped by multifeeding, and reset them.  
• Insufficient memory.  
Cause:  
There is not enough memory for tasks such as scanning and image  
processing. It is likely that a program is consuming a lot of GDI  
memory and/or there are too many applications and device drivers  
running in the background.  
Lower the resolution.  
User response:  
Don’t use the following image processing settings: Automatic Page  
Size Detection Priority=4, Dropout Color=”None” and Image  
Rotation.  
Don't compress the file when saving it.  
Change the PC memory's caching mode.  
Increase virtual memory.  
• An error occurred in the temporary file.  
Cause:  
Accessing the internal temporary file of the scanned image is causing  
the error. The disk space may be insufficient, the temporary file may  
be damaged, or other programs may be affecting disk access.  
User response:  
Increase the free space of the disk. Check the hard disk (chkdsk and  
scandsk). Make sure that no other program is accessing the disk. If  
the error message persists, contact the retail store where the product  
was purchased or the nearest service center.  
• Download file not found.  
Cause:  
A file specified as a dither pattern or gamma pattern cannot be found.  
Check that the download file is in the specified directory. Otherwise,  
User response:  
99  
use the file selection dialog to specify an available file.  
• Illegal format or data in download file.  
Cause:  
The format of the specified download file is illegal or the data is  
incorrect.  
User response:  
User response: Use an editor to check file format and data.  
• ASPI manager not found.  
Cause:  
The ASPI manager may not have been installed, or may have been  
deleted.  
User response:  
Reinstall the products, including the ASPI manager attached to the  
SCSI board. Then reboot the PC.  
• Scanner DLL file not found.  
Cause:  
An image scanner was selected, but the DLL file of the selected image  
scanner has not been installed in the directory in which this driver is  
installed.  
User response:  
Perform the setup again.  
• A parameter error has occurred (internally)  
• The calling procedure is invalid (internally).  
• The area is specified incorrectly (internally).  
• The calculation result exceeded the value that can be expressed (internally).  
• User definition is not registered (internally).  
• Illegal value is received during communication with scanner. (internally).  
Cause:  
This is a program error that occurs during command exchange  
between the driver and the image scanner.  
User response:  
Try again by rebooting the machine. If the error persists, contact the  
retail store where the product was purchased or the nearest service  
center.  
• A general fault of the MSG_XXXXX response (internally).  
Cause:  
This is a program error that usually occurs during internal message  
transfer. This message involves the sub-messages described later.  
User response:  
Contact the retail store where the product was purchased or the  
nearest service center.  
• A general fault of the DAT_XXXXX response (internally).  
Cause: This is a program error that usually occurs during internal data  
100  
transfer. This message involves the sub-messages described later.  
User response:  
Contact the retail store where the product was purchased or the  
nearest maintenance service center.  
• A general fault of the DAT_XXXXX, MSG_SET, and unsupported type response.  
(Internally)  
Cause:  
This is a program error that usually occurs while making the internal  
data settings.  
User response:  
Contact the place of purchase or your nearest maintenance and service  
center.  
• An undefined error occurred  
• Processing cannot be continued because of insufficient memory.  
• The data source cannot be found.  
• The driver is connected to a maximum number of applications supported.  
• An operation error occurred.  
• An invalid function is specified.  
• Unpermitted combination of MSG DG DAT.  
• An invalid value is specified.  
• An invalid procedure of DG DAT MSG is specified.  
Cause:  
These sub-messages are added to the error messages "General  
MSG_XXXXX response violation (internal)" and "General  
DAT_XXXXX violation (internal)." These sub- messages indicate  
details about the programming errors that occur during message and  
data processing.  
User response:  
Contact the retail store where the product was purchased or the  
nearest service center.  
101  
8.1.2. Error messages relating to gamma correction pattern editing  
• Enter a positive decimal value.  
Cause:  
A value other than a number has been entered as the gamma  
correction value.  
Alternatively, 0 or a negative value has been entered.  
User response:  
Reenter a valid value.  
• The file could not be created.  
Cause:  
The file for saving could not be created. There is insufficient space to  
save the file or the disk to which the file was to be saved is corrupted.  
Alternatively, writing to the directory in which the file was to be  
saved may not be allowed or other programs relating to disk access  
may be affecting performance.  
User response:  
Increase the amount of available space on the disk.  
Use a utility such as chkdsk or scandisk to check the hard disk.  
Ensure that any background programs that access the disk are not  
operating  
If this error message continues to be displayed, contact the place of  
purchase or your nearest maintenance and service center.  
• The file cannot be opened.  
Cause:  
The file could not be opened.  
The specified file name may be incorrect or the disk from which it is  
being read may be corrupted. Alternatively, the specified file may be  
a write-only file or other programs relating to disk access may be  
affecting performance.  
User response:  
If the specified filename is correct, use a utility such as chkdsk or  
scandisk to check the hard disk. Ensure that no background programs  
that access the disk are operating.  
If this error message continues to be displayed, contact the place of  
purchase or your nearest maintenance and service center.  
• There is a file formatting error.  
Cause:  
There is an error in the format of the specified file. Either an incorrect  
file has been specified or the content of the specified file is incorrect.  
User response:  
After checking the users' manual, check that the content of the  
specified file is correct.  
102  
 
8.1.3. Messages concerning to FUJITSU Scanner Control Center  
• Failed to start-up the application. Check the setting of FUJITSU Scanner Control  
Center.  
• The setting of the path is blank. Check the setting of FUJITSU Scanner Control  
Center.  
• Can not find the specified file. Check if the specified path and file name is correct.  
• Can not find the specified work folder. Check if the specified path is correct.  
Cause:  
The setting of the application may be inadequate.  
User response:  
Check setting items of [General] in [Application Dialog] and make  
sure settings are correct and there is no omission. If you find any  
incorrect setting or omission, correct it.  
• The same Plug-in has been installed already. Specified Plug-in can not install.  
Cause:  
An attempt was made to install the same plug-in that has been already  
installed.  
User response:  
Two or more plug-ins assigned to the same name cannot be installed.  
• The specified file is not the effective plug-in. Specified file can not install.  
• Can not find the entry point of the specified plug-in. Specified file can not install.  
Cause:  
The specified file may not be the effective plug-in.  
User response:  
Check whether the specified file is the effective plug-in and retry.  
• Exceeded the number of plug-in to be supported. Can not install the new plug-in.  
Cause:  
The number of plug-ins to be supported was exceeded.  
User response:  
The maximum number of plug-ins that can be supported is 50. Delete  
unnecessary plug-ins in the folder where FUJITSU Scanner Control  
Center has been installed, then install another plug-in.  
• The plug-in has not been installed.  
Cause:  
The check box "Use a Plug-In" was checked but no plug-in has been  
installed.  
User response:  
To use a plug-in, install a plug-in, then check the check box "Use a  
Plug-In."  
• Can not find the application for the Plug-in use. Can not use the specified plug-in  
Cause:  
The application to be used for the plug-in may not have been installed.  
User response:  
Verify that the application to be used for the plug-in has been  
installed. If no application is found, install it.  
103  
 
• Scanner could not find although it searched again. Check the connection of the  
scanner and retry again  
Cause:  
The scanner power may not have been turned on or the cable may  
have been connected incorrectly. Otherwise, the OS may not  
recognize the scanner.  
User response:  
Make sure that the scanner power has been turned on and the cable  
has been connected correctly, then retry rescanning. Or, check if the  
OS recognizes the scanner. If the OS does not recognize it, let it  
recognize the scanner, then retry.  
• Can not rescan the scanner. Close the application using the driver and retry again.  
Cause:  
An attempt was made to rescan while the driver was in use.  
User response:  
It is impossible to rescan while the driver is in use. Close the  
application that uses the driver and retry.  
• Can not get the EEPROM data. The setting of the function key can not change.  
Check the connection of the scanner.  
• Can not change the setting of the function key. Check the connection of the scanner  
and try the operation again.  
Cause:  
While the scanner with function keys are being monitored, the scanner  
power may be turned off or the cable may be connected incorrectly.  
User response:  
Make sure that the scanner power has been turned on and the cable  
has been connected correctly.  
• It is not authorized to write into the folder which is installed FUJITSU Scanner Control  
Center. Can not change the function of the function key. Check the Access Authority  
of the folder which is installed FUJITSU Scanner Control Center.  
Cause:  
While the scanner with function keys are being monitored, Access  
Authority may not have been set to the folder where the FUJITSU  
scanner Control Center has been installed.  
User response:  
To change the setting of the function key, Access Authority of the  
folder where FUJITSU scanner Control Center has been installed is  
required. Set Access Authority to the folder where FUJITSU scanner  
Control Center has been installed, or execute it with Administrator  
Authority.  
• Scanner is not selected. Please select a scanner.  
Cause:  
The OK button was pressed without selecting the scanner in the  
scanner select dialog.  
User response:  
Press the OK button after selecting the scanner to be monitored.  
104  
8.1.4. Messages relating to the Firmware Updater  
• The firmware updater is already running.  
Cause:  
The same application software is tried to execute concurrently.  
Use the one already executed.  
User response:  
• ASPI manager has not been installed. Please install the ASPI manager.  
• ASPI manager of unsupported revision has been installed. Please install the ASPI  
manager of the revision 4.1 or later.  
Cause:  
The ASPI manager has not been installed, or revision may be old.  
User response:  
After installing the ASPI manager of revision 4.0 or later (For  
Windows® 2000 or Windows® Me, 4.60 or later; For Windows® XP,  
4.70 or later), execute this application software.  
• More than one scanner is connected. Please connect only one scanner.  
Cause:  
Scanners other than the one with the firmware to be updated are  
connected. (If more than one scanner is connected, the applicable  
scanner cannot be detected properly resulting in the unsuccessful  
update.)  
User response:  
Connect one scanner to be updated, and then execute this application  
software.  
• The scanner is in the emulation mode. Please release it from the emulation mode.  
Cause:  
Connected scanner device has been set to the emulation mode.  
User response:  
Referring the Operator’s Guide of the device, cancel the emulation  
mode, and then execute this application software.  
• The driver of the scanner is in use now. Close the application software using the  
driver.  
Cause:  
This application software cannot be executed with the driver  
activated.  
User response:  
Close the application software that is using the driver, and then  
execute the application software.  
• Failed to obtain the model revision. Please check the connection of the device.  
Cause:  
The device information may not have been obtained due to the wrong  
connection of the scanner.  
User response:  
After confirming the scanner connection, execute the application  
software again.  
105  
 
• The applicable scanner is not connected or the driver is in use. Please connect the  
applicable scanner or close the application software using the driver. The process is  
cancelled.  
Cause:  
The scanner may not been connected properly or the driver may be  
used.  
User response:  
Check the connection of the device or close the application software if  
it is using the driver. Then execute this application software again.  
• Failed to load the Flashwt.dll.  
• Localize DLL version is different.  
• Data file is incorrect. The process is cancelled.  
Cause:  
The relevant dill fail or the data file for update has not been installed  
correctly, broken or deleted  
User response:  
See section 3 and install the driver again.  
106  
8.2. Device Trouble Related to Operation  
• The [Scan] button is pressed, but scanning is not performed.  
Cause:  
Has the scanner power been turned on? Has the SCSI cable been  
connected correctly? Has the correct device type been selected using  
[Select TWAIN Input Device]?  
• The scanner appears to be operating, but no image is displayed.  
Cause:  
Has the SCSI cable between the scanner and the main unit been  
connected correctly?  
Is the [Brightness] value or [Threshold] value too small?  
When the [Minimize] button is pressed, is the [Restore] button  
displayed?  
Is the application set to perform only file output?  
User response:  
If the [Restore] button is displayed after the [Minimize] button is  
pressed, the problem could be the display driver that is being used.  
Contact the manufacturer of the display driver.  
If a file has been selected as output destination with the environment  
settings by the image scanner operation confirmation utility, try to  
change to screen output.  
• When you don’t know how to replace consumables.  
User response: Refer to section 6 “How to Use the FUJITSU Scanner Control  
Center”- [About how to replace consumables] for replacement  
procedure of consumables.  
Also see the Operator’s guide of the scanner for how to replace  
consumables.  
107  
 
9. Appendix  
9.1. Relevant Image Scanner Specification  
Product:  
M3091DC (fi-4110C)  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning  
Light source:  
Fluorescent tube (White)  
300 dpi  
Basic resolution:  
Output resolution1:  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Color (24bit) output:  
ADF scanning speed 2:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Single sided: 15 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 7.5 pages per minute (200 dpi, A4, 55kg)  
(=15 screens per minute)  
Color  
Single sided: 5 pages per minute (150 dpi, A4, 55 kg)  
Double sided: 2.5 pages per minute (150 dpi, A4, 55kg)  
(=5 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, ream weight: 55 kg, High quality paper,  
normal temperature and humidity)  
Minimum 52mm x 74 mm  
Maximum 216 mm x 356 mm  
Supported regular paper 3:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
1
Change processing is done inside the driver.  
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3
.
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
108  
         
Image processing function: Simplified Dynamic Threshold (floating slice), De-Screen,  
Edge emphasis, Reverse, 256 Color, 8 Color  
Individual setting:  
Interface:  
Disabled  
SCSI-II  
Preview:  
Enabled (at ADF scanning)  
Enabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression): Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option : Enabled  
109  
Product:  
fi-4120C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning1,  
Long page scanning  
Black&White  
: Max 216mm x 711mm  
Grayscale, Color 2 : Max 216mm x 610mm  
Fluorescent tube (White)  
Light source:  
Basic resolution:  
Output resolution:  
600 dpi  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Color (24bit) output:  
ADF scanning speed 3:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 12.5 pages per minute (200 dpi, A4, 80g/m2)  
(=25 screens per minute)  
Color  
Single sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 12.5 pages per minute (150 dpi, A4, 80g/m2)  
(=25 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm  
Supported regular paper 4:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
1
Individual setting : Disabled  
2
In case of color or grayscale, the firmware version of scanner has to be “D00” or latter.  
3
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
4
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
110  
       
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale  
Reverse  
Individual setting:  
Interface:  
Disabled  
SCSI-II, USB1.1  
Enabled (at ADF scanning)  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option : Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
111  
Product:  
fi-4120C2  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning1,  
Long page scanning : Max 216mm x 864mm  
Light source:  
Fluorescent tube (White)  
600 dpi  
Basic resolution:  
Output resolution:  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Color (24bit) output:  
ADF scanning speed 2:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
(= 50 screens per minute)  
Color  
Single sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
(= 50 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm  
Supported regular paper 3:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale, Reverse  
1
2
Individual setting : Disabled  
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
112  
     
Individual setting:  
Disabled  
Imprinter (Endorser):  
With Imprinter option  
(Reverse side, minimum left margin printing position of 5mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom  
Font (orientation) : Vertical / Horizontal  
Bold font : Enabled  
Interface:  
SCSI-II, USB1.1/2.0  
Enabled (at ADF scanning)  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option : Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the printing position, printing will begin 5 mm from the edge of the page.  
113  
 
Product:  
M3092DC (fi-4210C)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed Flat bed (FB), Automatic Document Feed (ADF),  
Simultaneous double-sided scanning  
Light source:  
Fluorescent tube (White)  
Basic resolution:  
Output resolution1:  
600dpi (FB), 300 dpi (ADF)  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Color (24bit) output:  
ADF scanning speed 2:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Single sided: 15 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 7.5 pages per minute (200 dpi, A4, 55kg)  
(=15 screens per minute)  
Color  
Single sided: 5 pages per minute (150 dpi, A4, 55 kg)  
Double sided: 2.5 pages per minute (150 dpi, A4, 55kg)  
(=5 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, ream weight: 55 kg, High quality paper,  
normal temperature and humidity)  
Minimum 52mm x 74 mm  
Maximum 216 mm x 356 mm  
Supported regular paper 3:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
Image processing function: Simplified Dynamic Threshold (floating slice),  
De-Screen, Edge emphasis, Reverse, 256 Color, 8 Color  
Individual setting:  
Disabled  
1
Change processing is done inside the driver.  
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3
.
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
114  
     
Interface:  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning, ADF scanning)  
Flip Side Rotation:  
Rotation:  
Enabled  
Enabled  
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Enabled  
115  
Product:  
fi-4220C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Document fixed Flat bed (FB), Automatic Document Feed (ADF),  
Simultaneous double-sided scanning1,  
Long page scanning  
Black&White  
: Max 216mm x 711mm  
Grayscale, Color 2 : Max 216mm x 610mm  
Fluorescent tube (White)  
Light source:  
Basic resolution:  
Output resolution:  
600dpi  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Color (24bit) output:  
Flat bed scanning speed:  
B/W : 2.2 sec or less (200 dpi, A4)  
Color : 2.1 sec or less (150 dpi, A4)  
ADF scanning speed 3:  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 12.5 pages per minute (200 dpi, A4, 80g/m2)  
(=25 screens per minute)  
Color  
Single sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 12.5 pages per minute (150 dpi, A4, 80g/m2)  
(=25 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm <ADF>  
Maximum 216 mm x 297 mm <Flat Bed>  
Supported regular paper 4:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast: 255 steps  
1
Individual setting : Disabled  
2
In case of color or grayscale, the firmware version of scanner has to be “D00” or latter.  
3
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
4
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
116  
       
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale, Reverse  
Individual setting:  
Interface:  
Disabled  
SCSI-II, USB1.1  
Preview:  
Enabled (at Flat bed scanning, ADF scanning)  
Flip Side Rotation:  
Rotation:  
Enabled  
Enabled  
Automatic Size and Skew detection: End of Page Detection  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
117  
Product:  
fi-4220C2  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Document fixed Flat bed (FB), Automatic Document Feed (ADF),  
Simultaneous double-sided scanning1,  
Long page scanning : Max 216mm x 864mm  
Light source:  
Fluorescent tube (White)  
600dpi  
Basic resolution:  
Output resolution:  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Color (24bit) output:  
Flat bed scanning speed:  
B/W : 2.2 sec or less (200 dpi, A4)  
Color : 2.1 sec or less (150 dpi, A4)  
ADF scanning speed 2:  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
(=50 screens per minute)  
Color  
Single sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (150 dpi, A4, 80g/m2)  
(=50 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm <ADF>  
Maximum 216 mm x 297 mm <Flat Bed>  
Supported regular paper 3:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast: 255 steps  
High light / Shadow :  
255 steps (at Color / Grayscale scanning)  
1
2
Individual setting : Disabled  
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
118  
     
Gamma pattern:  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale, Reverse  
Individual setting:  
Interface:  
Disabled  
SCSI-II, USB1.1/2.0  
Preview:  
Enabled (at Flat bed scanning, ADF scanning)  
Flip Side Rotation:  
Rotation:  
Enabled  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option: Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
119  
Product:  
M3093GX 1 (device name: fi-4320S, VSP210)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed, scanner unit moving (flat bed),  
Automatic Document Feeder (ADF)  
Light source:  
Xe discharge tube (Green)  
400 dpi  
Basic resolution:  
Output resolution:  
Standard: 400, 300, 240, 200 dpi  
With image processing option: 50 dpi to 800 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
1.6 sec or less (A4, 200 dpi)  
Flat bed scanning speed:  
ADF scanning speed 2:  
ADF paper chute capacity:  
Document size 3:  
27 pages/minute (200 dpi, A4, 55 kg)  
Maximum 50 sheets, ream weight: 55kg, A4  
Maximum 216 mm x 356 mm Legal size paper  
Supported regular paper:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5, B6/B6 Landscape,  
Letter, Legal, US Executive  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold(SDTC)  
Image processing circuit II required,  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold(DTC), Smoothing, Filtering,  
Noise removal  
Individual setting:  
Interface:  
Disabled  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning only)  
Flip Side Rotation:  
Rotation:  
Disabled  
Enabled  
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
1. Use of this scanner requires that the image compression option board (CMP-2) be installed in the scanner.  
2. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3. Not all sizes of paper can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
120  
     
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
121  
Product:  
M3093DG (fi-4320, VSP220)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed, scanner unit moving (flat bed)  
Automatic Document Feeder (ADF)  
Simultaneous double-sided scanning  
Xe discharge tube (Green)  
400 dpi  
Light source:  
Basic resolution:  
Output resolution:  
Standard: 6001, 400, 300, 240, 200, 150, 100 dpi  
With image processing option: 50 dpi to 800 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Halftone Patterns:  
Flat bed scanning speed2:  
ADF scanning speed:  
Double-sided:  
Enabled (8 bits)  
Dither matrix (can be downloaded), Error diffusion  
1.6 sec or less (A4, 200 dpi)  
Single-sided:  
27 pages per minute (200 dpi, A4, 55 kg)  
22.5 pages per minute (200 dpi, A4, 55 kg)  
(= 45 screens per minute)  
ADF paper chute capacity:  
Maximum 50 sheets, (ream weight: 55kg, A4 [High quality paper,  
normal temperature and humidity])  
Document size:  
Maximum 216 mm x 356 mm  
Supported regular paper 3:  
A4, A5/A5 landscape, A6/A6 landscape, B5, B6/B6 landscape,  
Letter, Legal, US Executive  
Scanning area specification: Specified (one location)  
White level follower: Enabled  
Brightness / Threshold / Contrast: 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC)  
With image processing option  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
Interface:  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
1. An eight-megabyte expanded memory option can be loaded in some models.  
2. This speed is only specified in the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3. Not all sizes of paper can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
122  
     
Rotation:  
Automatic Size and Skew detection: End of Page Detection  
Overscan: Disabled  
Enabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
123  
Product:  
fi-4340C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD, Reduced optical system  
Document fixed Flat bed, Automatic Document  
Feed(ADF), Simultaneous double-sided scanning  
Long page scanning (216mm x 1541mm, Black&White only)  
Fluorescent tube (White)  
Light source:  
Basic resolution:  
Output resolution:  
600 dpi  
Standard: 50 dpi to 800 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Halftone Patterns:  
Color  
Enabled (8 bits)  
Dither matrix (can be downloaded), Error diffusion  
24bit  
Scanning speed:  
B/W : 1.2 sec or less (200 dpi, A4)  
Color : 2.8 sec or less (200 dpi, A4)  
ADF scanning speed 1:  
Single sided: 40 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 40 pages per minute (200 dpi, A4, 55kg)  
(=80 screens per minute)  
Color  
Single sided: 16 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 24.5 pages per minute (200 dpi, A4, 55kg)  
(=29 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 100 sheets, ream weight: 55 kg, A4 [High quality  
paper, normal temperature and humidity])  
Maximum 216 mm x 297 mm  
or Maximum 216mm x 1541 mm with Long Page Scanning Mode  
Supported regular paper 2:  
A4, A5/A5 Landscape, A6/A6 Landscape,  
B5, B6/B6 Landscape, Letter,, Legal  
Scanning area specification: Specified (one location)  
White level follower: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
124  
   
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis,  
Edge extraction, De-Screen, SEE(Selectable Edge Enhancement),  
Reverse, 256 Color, 8 Color  
With image processing option  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal,  
Automatic Separation  
Individual setting:  
Enabled (Brightness / Threshold / Contrast)  
Imprinter (Endorser):  
With imprinter option  
(Reverse side, minimum left margin printing position of 7 mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom, Bottom to Top  
SCSI-II, USB 2.0  
Interface:  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection :  
Page End Detect, Automatic Page Size Detect, Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Enabled (with JPEG option)  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the endorser print position, printing will begin 7 mm from the edge of the page.  
125  
 
Product:  
fi-4530C  
Desktop  
Type:  
Image sensor:  
Operating method:  
Color CCD  
Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning (Resolution free)  
Black&White  
Grayscale, Color  
: Maximum 297mm x 864mm  
: Maximum 297mm x 864mm  
Light source:  
Fluorescent tube (White)  
600 dpi  
Basic resolution:  
Output resolution:  
50 - 600 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Gray scale (8 bits) output:  
Halftone Patterns:  
Enabled  
Dither matrix (can be downloaded), Error diffusion  
Color (24bits) output:  
ADF scanning speed 1:  
Enabled  
Black & White  
Single sided: 35 pages per minute (200 dpi, A4, 80 kg)  
Double sided: 17.5 pages per minute (200 dpi, A4, 80 kg)  
(=35 screens per minute)  
Color  
Single sided: 45 pages per minute (150 dpi, A4, 80 kg)  
Double sided: 22.5 pages per minute (150 dpi, A4, 80kg)  
(=45 screens per minute)  
Hopper capacity:  
Maximum 100 sheets, (ream weight: 80 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Minimum 53 mm x 74 mm  
Maximum 297 mm x 432 mm.  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape,  
Business Card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Custom only  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
126  
   
Image processing function: Simplified Dynamic Threshold (SDTC)  
Edge emphasis, Edge extraction, De-screen, 256 color, 8 color,  
4bit Grayscale, Reverse  
Individual setting:  
Disabled  
Imprinter (Endorser):  
With Imprinter option  
(Reverse side, minimum left margin printing position of 5mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom  
Font (orientation) : Vertical / Horizontal  
Bold font : Enabled2  
Interface:  
Ultra SCSI, USB 2.0  
Enabled (at ADF scanning)  
Enabled  
Preview:  
Flip Side Rotaiton:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Enabled (Check overlapping / length)  
Enabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option : Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the printing position, printing will begin 5 mm from the edge of the page.  
The firmware version of scanner has to be “K00” or latter.  
2
127  
   
Product:  
M3096GX1 (fi-4620S, VSP310)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed, scanner unit moving (flat bed),  
Automatic Document Feed (ADF)  
Light source:  
Xe discharge tube (Green)  
400 dpi  
Basic resolution:  
Output resolution:  
Standard: 400, 300, 240, 200 dpi  
With image processing option: 50 dpi to 800 dpi (at steps of 1)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
2.0 sec or less (A4, 200 dpi)  
Flat bed scanning speed:  
ADF scanning speed 2:  
ADF paper chute capacity:  
21 pages/minute (200 dpi, A4, 55 kg)  
Maximum 50 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm A3 or Double letter sized paper  
Supported regular paper 3:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape,B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter, Letter Landscape,  
Legal, Double letter, US Executive/US Executive Landscape  
Scanning area specification: Specified (one location)  
White level follower: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma patterns:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC)  
Image processing option installed  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal  
Individual setting:  
Interface:  
Disabled  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning only)  
Flip Side Rotation:  
Rotation:  
Disabled  
Enabled  
Automatic Size and Skew detection: Disabled  
1. Use of this scanner may require installation of the optional image compression option board (CMP-2) in the  
scanner device.  
2. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system  
configuration.  
3. Not all sizes of paper can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
128  
     
Overscan:  
Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
129  
Product:  
fi-4640S  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed Flat bed, Automatic Document  
Feed(ADF)  
Long page scanning (297mm x 1387mm, Black&White only)  
Xe discharge tube (Green)  
Light source:  
Basic resolution:  
Output resolution:  
400 dpi  
Standard: 50 dpi to 800 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
0.9 sec or less (200 dpi, A4)  
Flat bed scanning speed:  
ADF scanning speed 1:  
ADF paper chute capacity:  
Single sided: 45 pages per minute (200 dpi, A4, 55 kg)  
Maximum 100 sheets, ream weight: 55 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
or Maximum 297mm x 1387 mm with Long Page Scanning Mode  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge  
extraction, SEE(Selectable Edge Enhancement), Reverse  
With image processing option  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal,  
Automatic Separation  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
130  
   
Individual setting:  
Disabled  
Imprinter (Endorser):  
With imprinter option  
(Reverse side, minimum left margin printing position of 42 mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction (Printing): Top to Bottom, Bottom to Top  
SCSI-II  
Interface:  
Preview:  
Enabled (at Flat bed scanning only)  
Disabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the endorser print position, printing will begin 42 mm from the edge of the page.  
131  
 
Product:  
M4097D (fi-4750, VSP330)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed Flat bed, Automatic Document  
Feed(ADF), Simultaneous double-sided scanning  
Long page scanning (297mm x 1387mm, Black&White only)  
Xe discharge tube(Green)  
Light source:  
Basic resolution:  
Output resolution:  
400 dpi  
Standard: 50 dpi to 800 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
0.9 sec or less (200 dpi, A4)  
Flat bed scanning speed:  
ADF scanning speed 1:  
Single sided: 50 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 45 pages per minute (200 dpi, A4, 55kg)  
(=90 screens per minute)  
ADF paper chute capacity:  
Maximum 100 sheets, ream weight: 55 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge  
extraction, SEE(Selectable Edge Enhancement), Reverse  
With image processing option  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal,  
Automatic Separation  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
132  
   
Imprinter (Endorser):  
With imprinter option  
(Reverse side, minimum left margin printing position of 42 mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction (Printing): Top to Bottom, Bottom to Top  
SCSI-II  
Interface:  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the endorser print position, printing will begin 42 mm from the edge of the page.  
133  
 
Product:  
fi-4750L  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed Flat bed, Automatic Document  
Feed(ADF), Simultaneous double-sided scanning  
Long page scanning (297mm x 1387mm, Black&White only)  
Xe discharge tube (Green)  
Light source:  
Basic resolution:  
Output resolution:  
400 dpi  
Standard: 50 dpi to 800 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
0.9 sec or less (200 dpi, A4)  
Flat bed scanning speed:  
ADF scanning speed 1:  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 50 pages per minute (200 dpi, A4, 55kg)  
(=100 screens per minute)  
ADF paper chute capacity:  
Maximum 250 sheets, ream weight: 55 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis, Edge  
extraction, SEE(Selectable Edge Enhancement), Reverse  
With image processing option  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal,  
Automatic Separation  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
134  
   
Imprinter (Endorser):  
With imprinter option  
(Reverse side, minimum left margin printing position of 42 mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom, Bottom to Top  
SCSI-II  
Interface:  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the endorser print position, printing will begin 42 mm from the edge of the page.  
135  
 
Product:  
fi-4750C  
Type:  
Desktop  
Image sensor:  
Operating method:  
LED(RGB) + Reduced optical system  
Document fixed Flat bed, Automatic Document  
Feed(ADF), Simultaneous double-sided scanning  
Long page scanning (297mm x 1387mm, Black&White only)  
Light source:  
LED (R, G, B)  
Basic resolution:  
Horizontal scanning: 400 dpi  
Vertical scanning: 800,700,600,500, 400, 300, 240, 200, 150,  
100 dpi  
Output resolution:  
Standard: 50 dpi to 800 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Halftone Patterns:  
Color  
Enabled (8 bits)  
Dither matrix (can be downloaded), Error diffusion  
24bit  
Flat bed scanning speed:  
B/W : 0.9 sec or less (200 dpi, A4)  
Color : 3.6 sec or less (200 dpi, A4)  
ADF scanning speed 1:  
Single sided: 50 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 45 pages per minute (200 dpi, A4, 55kg)  
(=90 screens per minute)  
Color  
Single sided: 12 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 11.5 pages per minute (200 dpi, A4, 55kg)  
(=23 screens per minute)  
ADF paper chute capacity:  
Maximum 100 sheets, ream weight: 55 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
136  
   
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis,  
Edge extraction, De-Screen, SEE(Selectable Edge Enhancement),  
Reverse, 256 Color, 8 Color  
With image processing option  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal,  
Automatic Separation  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern / Image processing function)  
Imprinter (Endorser):  
With imprinter option  
(Reverse side, minimum left margin printing position of 42 mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom, Bottom to Top  
SCSI-II  
Interface:  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Enabled (with JPEG option)  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the endorser print position, printing will begin 42 mm from the edge of the page.  
137  
 
Product:  
M3097G1  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed, scanner unit moving (flat bed),  
Automatic Document Feed (ADF)  
Light source:  
Fluorescent tube (Green)  
400 dpi  
Basic resolution:  
Output resolution:  
Standard: 400, 300, 240, 200 dpi  
With image processing option: 50 dpi to 1,600 dpi  
(at steps of 1)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Enabled (8 bits) Some release version of scanner do not support  
gray-scale output format  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
Flat bed scanning speed:  
1.3 sec or less (A4, 200 dpi)  
3.7 sec or less (A3, 400 dpi)  
ADF scanning speed 2:  
36 pages/minute (200 dpi, A4, 55 kg)  
ADF paper chute capacity:  
Maximum 100 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 3:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Scanning area specification: Specified (one location)  
White level follower: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC)  
Image processing option installed  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal  
Individual setting:  
Interface:  
Disabled  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning only)  
Flip Side Rotation:  
Rotation:  
Disabled  
Enabled  
1. Use of this scanner may require installation of the optional image compression board (CMP-2).  
2. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
3. Not all sizes of paper can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
138  
     
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
139  
Product:  
M3097DG  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Document fixed, scanner unit moving (flat bed),  
Automatic Document Feed (ADF)  
Simultaneous double-sided scanning  
Light source:  
Xe discharge tube (Green)  
400 dpi  
Basic resolution:  
Output resolution:  
Standard: 600, 400, 300, 240, 200, 150, 100 dpi  
With image processing option: 50 dpi to 800 dpi  
(at steps of 1 dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
1.3 seconds or less (A4, 200 dpi)  
Flat bed scanning speed:  
ADF scanning speed 1:  
Single sided: 36 pages per minute (200 dpi, A4, 55 kg)  
Double sided:30 pages per minute (200 dpi, A4, 55 kg)  
(= 60 screens per minute)  
ADF paper chute capacity:  
Maximum 100 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, Double Letter, Letter/Letter landscape, Legal,  
US Executive/ US Executive Landscape  
Cutout specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function:  
Simplified Dynamic Threshold (SDTC)  
With image processing option  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal.  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
Interface:  
SCSI-II  
Preview:  
Enabled (at Flat bed scanning only)  
Enabled  
Flip Side Rotation:  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
140  
   
Rotation:  
Automatic Size and Skew detection: End of Page Detection  
Overscan: Disabled  
Enabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (only when ram cache is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
141  
Product:  
fi-4860C/fi-4860C2 1  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning (297mm x 878mm, Black&White only)  
Light source:  
Fluorescent tube (White)  
400 dpi  
Basic resolution:  
Output resolution:  
Monochrome: 400, 300, 240, 200, 150, 100dpi  
Color: 400, 300, 200, 150, 100dpi  
Grayscale levels (internal): 10 bit 1024 levels  
Gray scale (8 bits) output:  
Halftone Patterns:  
Color  
Enabled  
Dither matrix, Error diffusion  
24bit  
ADF scanning speed 2:  
<Monochrome Asynchronous Scanning>  
Single sided: 60 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 60 pages per minute (200 dpi, A4, 80g/m2)  
(= 120 screens per minute)  
<Color Asynchronous Scanning>  
Single sided: 60 pages per minute (150,200 dpi, A4, 80g/m2)  
Double sided: 60 pages per minute (150,200 dpi, A4, 80g/m2)  
(= 120 screens per minute)  
Hopper capacity:  
Document size:  
Maximum 500 sheets, (80g/m2, A4 [High quality paper, Normal  
temperature and humidity])  
Maximum 297 mm x 432 mm  
or 297mm x 878 mm with Long Page scanning mode.  
Supported regular paper 3:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape  
Cutout specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
1. For fi-4860C2, the FUJITSU TWAIN 32 Scanner Driver V8.18.166 or later is required.  
2. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration. Color scanning speed is a value with JPEG enabled.  
3. Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
142  
     
Image processing function: Dynamic Threshold (SDTC, DTC),  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image(Black&White only), Reverse, 256 Color, 8 Color,  
4bit Grayscale  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern / Image processing function)  
Imprinter (Endorser):  
With Imprinter option (Pre-Imprinter / Post-Imprinter)  
(Reverse side, minimum left margin printing position of 5 mm) 1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction (Printing): Top to Bottom  
Pre-Imprinter / Post-Imprinter switching: Enabled  
Interface:  
Ultra Wide SCSI  
Disable  
Preview:  
Flip Side Rotation:  
Enabled  
Rotation:  
Enabled  
Automatic Size and Skew detection2: End of Page Detection, Automatic Deskew,  
Automatic Page Size Detection, Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection3:  
Multifeed detection:  
Pre-Pick:  
Enabled (Check thickness / length)  
Enabled  
Check Over-skew:  
Blank page skip:  
Enabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
1
2
3
If 0 mm is specified as the endorser print position, printing will begin 5 mm from the edge of the page.  
The “Automatic Deskew” and “Automatic Page Size Detection” are not supported with color scanning.  
Batch Detection can not be used with following Caching, “Use Memory on Scanner” or “Use Both Memory”.  
143  
     
Product:  
M4099D (fi-4990)  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning (297mm x 878mm, Black&White only)  
Light source:  
Fluorescent tube (White)  
400 dpi  
Basic resolution:  
Output resolution:  
Standard: 400, 300, 240, 200, dpi  
With image processing option: 50 dpi to 400 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Gray scale (8 bits) output:  
Halftone Patterns:  
ADF scanning speed 1:  
Enabled (200 dpi only)  
Dither matrix (can be downloaded), Error diffusion  
<Asynchronous Scanning>  
Single sided: 90 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 90 pages per minute (200 dpi, A4, 55 kg)  
(= 180 screens per minute)  
< Synchronous Scanning >  
Single sided: 80 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 60 pages per minute (200 dpi, A4, 55 kg)  
(= 120 screens per minute)  
Hopper capacity:  
Maximum 1,000 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape  
Cutout specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC)  
With image processing option  
Edge emphasis, Edge extraction, Automatic separation, Reverse,  
Dynamic Threshold (DTC), Smoothing, Filtering, Noise removal  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
144  
   
Imprinter (Endorser):  
With endorser option  
(Reverse side, minimum left margin printing position of 20 mm)1  
Maximum number of characters to be printed: 30 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
(There are partly limitations by the revision of the scanner  
device.)  
Direction(Printing): Top to Bottom  
Interface:  
SCSI-II  
Disabled  
Enabled  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Automatic Size and Skew detection: End of Page Detection, Automatic Deskew  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection2:  
Multifeed detection:  
Pre-Pick:  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
2
If 0 mm is specified as the endorser print position, printing will begin 20 mm from the edge of the page.  
Batch Detection can not be used with following Caching, “Use Memory on Scanner” or “Use Both Memory”.  
145  
   
Product:  
fi-4990C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning (297mm x 878mm, Black&White only)  
Light source:  
Fluorescent tube (White)  
400 dpi  
Basic resolution:  
Output resolution:  
Monochrome: 400, 300, 240, 200, 150, 100dpi  
Color: 400, 300, 200, 150, 100dpi  
Grayscale levels (internal): 10 bit 1024 levels  
Gray scale (8 bits) output:  
Halftone Patterns:  
Color  
Enabled  
Dither matrix, Error diffusion  
24bit  
ADF scanning speed 1:  
<Monochrome, Asynchronous Scanning>  
Single sided: 90 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 90 pages per minute (200 dpi, A4, 55 kg)  
(= 180 screens per minute)  
Hopper capacity:  
Maximum 1,000 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 297 mm x 432 mm  
or 297mm x 878 mm with Long Page scanning mode.  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape  
Cutout specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
Image processing function: Dynamic Threshold (SDTC, DTC),  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image(Black&White only), Reverse, 256 Color, 8 Color,  
4bit Grayscale  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
146  
   
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern / Image processing function)  
Imprinter (Endorser):  
With endorser option  
(Reverse side, minimum left margin printing position of 20 mm)1  
Maximum number of characters to be printed: 30 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
(There are partly limitations by the revision of the scanner  
device.)  
Direction(Printing): Top to Bottom  
Interface:  
Ultra Wide SCSI  
Disabled  
Preview:  
Flip Side Rotation:  
Enabled  
Rotation:  
Enabled  
Automatic Size and Skew detection2: End of Page Detection, Automatic Deskew,  
Automatic Page Size Detection, Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection3:  
Multifeed detection:  
Pre-Pick:  
Enabled (Check thickness / length)  
Disabled  
Check Over-skew:  
Blank page skip:  
Enabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
1
2
3
If 0 mm is specified as the endorser print position, printing will begin 20 mm from the edge of the page.  
The “Automatic Deskew” and “Automatic Page Size Detection” are not supported with color scanning.  
Batch Detection can not be used with following Caching, “Use Memory on Scanner” or “Use Both Memory”.  
147  
     
Product:  
M3099G, M3099GX  
Desktop  
Type:  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning  
Light source:  
Fluorescent tube (Green)  
Basic resolution:  
Output resolution:  
Horizontal scanning: 200 dpi  
Standard: 400, 300, 240, 200, dpi  
With image processing option: 50 dpi to 400 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Disabled  
Halftone Patterns:  
ADF scanning speed 1:  
Dither matrix (can be downloaded), Error diffusion  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided:50 pages per minute (200 dpi, A4, 55 kg)  
(= 100 screens per minute)  
<M3099GX>  
Single sided: 60 pages per minute (200 dpi, A4, 55 kg)  
Double sided:50 pages per minute (200 dpi, A4, 55 kg)  
(= 100 screens per minute)  
Hopper capacity:  
<M3099G>  
Maximum 500 sheets, ream weight: 55 kg, A4  
<M3099GX>  
Maximum 1,000 sheets, ream weight: 55 kg, A4  
Maximum 297 mm x 432 mm  
Document size:  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape  
Cutout specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function:  
Simplified Dynamic Threshold (SDTC)  
With image processing option  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
148  
   
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
Imprinter (Endorser):  
With imprinter (endorser) option  
(Reverse side, minimum left margin printing position of 20 mm)1  
Maximum number of characters to be printed: 20 characters  
Counter display range: 0 to 65535 (5 digits display)  
Direction (Printing): Top to Bottom  
Interface:  
SCSI-II  
Disabled  
Enabled  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
1
.
If 0 mm is specified as the endorser print position, printing will begin 20 mm from the edge of the page.  
149  
 
Product:  
M3099GH  
Type:  
Desktop  
Image sensor:  
Operating method:  
Reduced optical system  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning  
Light source:  
Fluorescent tube (Green)  
200 dpi  
Basic resolution:  
Output resolution:  
Standard: 400, 300, 240, 200, dpi  
with image processing option: 50 dpi to 400 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 8 bit 256 levels  
Grayscale output:  
Halftone Patterns:  
ADF scanning speed 1:  
Double sided:  
Disabled  
Dither matrix (can be downloaded), Error diffusion  
Single sided: 80 pages per minute (200 dpi, A4, 55 kg)  
60 pages per minute (200 dpi, A4, 55 kg)  
(= 120 screens per minute)  
Hopper capacity:  
Maximum 1,000 sheets, (ream weight: 55 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Maximum 216 mm x 356 mm  
Supported regular paper 2:  
A4/A4 Landscape, A5/A5 Landscape, B5, B6/B6 Landscape,  
Letter, Legal, US Executive  
Cutout specification:  
White level follower:  
Specified (one location)  
Enabled  
Brightness / Threshold / Contrast : 255 steps  
Gamma pattern:  
3 internal types (can be downloaded)  
Image processing function:  
Simplified Dynamic Threshold (SDTC)  
With image processing option  
Edge emphasis, Edge extraction, Automatic separation, Mirror  
image, Reverse, Dynamic Threshold (DTC), Smoothing, Filtering,  
Noise removal  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / Gamma pattern /  
Image processing function)  
Imprinter (Endorser):  
With imprinter (endorser) option  
(Reverse side, minimum left margin printing position of 20 mm)3  
Maximum number of characters to be printed: 20 characters  
Counter display range: 0 to 65535 (5 digits display)  
Direction (Printing): Top to Bottom  
SCSI-II  
Interface:  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
3
If 0 mm is specified as the endorser print position, printing will begin 20 mm from the edge of the page.  
150  
     
Preview:  
Disabled  
Enabled  
Enabled  
Flip Side Rotation:  
Rotation:  
Automatic Size and Skew detection: Disabled  
Overscan: Disabled  
Buffer scan ([Use Memory on Scanner]) function: Disabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Disabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Disabled  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] is used)  
JPEG Transfer (Hardware Compression) : Disabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Disabled  
Disabled  
Use Image Processing Software Option: Disabled  
Use of FUJITSU Scanner Control Center: Disabled  
151  
Product:  
fi-5120C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Automatic Document Feed (ADF), Simultaneous double-sided  
scanning,  
Long page scanning : Max 216mm x 864mm  
Light source:  
Fluorescent tube (White)  
600 dpi  
Basic resolution:  
Output resolution:  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Color (24bit) output:  
ADF scanning speed 1:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
(= 50 screens per minute)  
Color  
Single sided: 30 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 30 pages per minute (150 dpi, A4, 80g/m2)  
(= 60 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm  
Supported regular paper 2:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale, Reverse  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
152  
   
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern)  
Imprinter (Endorser):  
With Imprinter option  
(Reverse side, minimum left margin printing position of 5mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom  
Font (orientation) : Vertical (Normal) ,  
Horizontal (Normal / Narrow)  
Bold font : Enabled  
Interface:  
SCSI-II, USB1.1/2.0  
Enabled (at ADF scanning)  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Enabled (Check overlapping / length, Area selection)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option : Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
Device set: Consumables replace (Pad / Pick Roller / Remaining Ink counter clear)  
Offset Setting, Vertical magnification Adjustment, Lamp timer  
Area Selection for Multifeed Detection, Power ON/OFF Control setting  
1
If 0 mm is specified as the printing position, printing will begin 5 mm from the edge of the page.  
153  
 
Product:  
fi-5220C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD (Reduced optical system)  
Document fixed Flat bed (FB), Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning : Max 216mm x 864mm  
Light source:  
Fluorescent tube (White)  
600dpi  
Basic resolution:  
Output resolution:  
50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Enabled (8 bits)  
Halftone Patterns:  
Dither matrix (can be downloaded), Error diffusion  
Enabled  
Color (24bit) output:  
Flat bed scanning speed:  
B/W : 2.2 sec or less (200 dpi, A4)  
Color : 1.7 sec or less (150 dpi, A4)  
ADF scanning speed 1:  
Single sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
Double sided: 25 pages per minute (200 dpi, A4, 80g/m2)  
(=50 screens per minute)  
Color  
Single sided: 30 pages per minute (150 dpi, A4, 80g/m2)  
Double sided: 30 pages per minute (150 dpi, A4, 80g/m2)  
(=60 screens per minute)  
ADF paper chute capacity:  
Document size:  
Maximum 50 sheets (A4, 80g/m2, High quality paper, normal  
temperature and humidity)  
Minimum 53mm x 74 mm  
Maximum 216mm x 355.6mm <ADF>  
Maximum 216 mm x 297 mm <Flat Bed>  
Supported regular paper 2:  
A4, A5/A5 Landscape, A6/A6 Landscape, B5,  
B6/B6 Landscape, Letter, Legal, US Executive, Name card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast: 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Internal types are not available. (Cannot be downloaded)  
At custom specification, entering a value enables to set a pattern.  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
154  
   
Image processing function: Simplified Dynamic Threshold (SDTC), De-Screen,  
Edge emphasis, 256 Color, 8 Color, 4bit Grayscale, Reverse  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern)  
Interface:  
SCSI-II, USB1.1/2.0  
Preview:  
Enabled (at Flat bed scanning, ADF scanning)  
Flip Side Rotation:  
Rotation:  
Enabled  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check overlapping / length, Area selection)  
Disabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option: Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
Device set: Consumables replace (Pad / Pick Roller counter clear)  
Offset Setting, Vertical magnification Adjustment, Lamp timer  
Area Selection for Multifeed Detection, Power ON/OFF Control setting  
155  
Product:  
fi-5530C  
Desktop  
Type:  
Image sensor:  
Operating method:  
Color CCD  
Automatic Document Feed (ADF),  
Simultaneous double-sided scanning,  
Long page scanning (Resolution free)  
Black&White  
Grayscale, Color  
: Maximum 297mm x 864mm  
: Maximum 297mm x 864mm  
Light source:  
Fluorescent tube (White)  
600 dpi  
Basic resolution:  
Output resolution:  
50 - 600 dpi (at steps of 1 dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Gray scale (8 bits) output:  
Halftone Patterns:  
Enabled  
Dither matrix (can be downloaded), Error diffusion  
Color (24bits) output:  
ADF scanning speed 1:  
Enabled  
Black & White  
Single sided: 35 pages per minute (200 dpi, A4, 80 kg)  
Double sided: 35 pages per minute (200 dpi, A4, 80 kg)  
(=70 screens per minute)  
Color  
Single sided: 45 pages per minute (150 dpi, A4, 80 kg)  
Double sided: 45 pages per minute (150 dpi, A4, 80kg)  
(=90 screens per minute)  
Hopper capacity:  
Maximum 100 sheets, (ream weight: 80 kg, A4 [High quality  
paper, Normal temperature and humidity])  
Document size:  
Minimum 53 mm x 74 mm  
Maximum 297 mm x 432 mm.  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Double Letter, Letter/Letter  
Landscape, Legal, US Executive/US Executive Landscape,  
Business Card  
Scanning area specification: Specified (one location)  
White level follower: Disabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
Custom only  
1. This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
2
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
156  
   
Image processing function: Simplified Dynamic Threshold (SDTC), Advanced DTC,  
Edge emphasis, Edge extraction, De-screen, 256 color, 8 color,  
4bit Grayscale, Reverse  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern)  
Imprinter (Endorser):  
With Imprinter option  
(Reverse side, minimum left margin printing position of 5mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom  
Font (orientation) : Vertical (Normal) ,  
Horizontal (Normal / Narrow)  
Bold font : Enabled  
Interface:  
Ultra SCSI, USB 2.0  
Enabled (at ADF scanning)  
Enabled  
Preview:  
Flip Side Rotaiton:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled (when “Black Background” is selected)  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Disabled  
Enabled (Check overlapping / length, Area selection)  
Enabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option : Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
Device set: Consumables replace (Pad / Pick Roller / Remaining Ink counter clear)  
Offset Setting, Vertical magnification Adjustment, Lamp timer  
Area Selection for Multifeed Detection, Power ON/OFF Control setting  
1
If 0 mm is specified as the printing position, printing will begin 5 mm from the edge of the page.  
157  
 
Product:  
fi-5650C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD + Reduced optical system  
Automatic Document Feed(ADF), Simultaneous double-sided  
scanning  
Long page scanning (305mm x 864mm)  
Fluorescent tube (White)  
Light source:  
Basic resolution:  
Output resolution:  
600 dpi  
Standard: 50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Halftone Patterns:  
Color output  
Enabled (8 bits)  
Dither matrix (can be downloaded), Error diffusion  
Enabled (24bit)  
ADF scanning speed 1:  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 55 pages per minute (200 dpi, A4, 55kg)  
(=110 screens per minute)  
Color  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 55 pages per minute (200 dpi, A4, 55kg)  
(=110 screens per minute)  
ADF paper chute capacity:  
Maximum 200 sheets, ream weight: 80 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Minimum 53mm x 74mm, Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis,  
Edge extraction, De-Screen, SEE(Selectable Edge Enhancement),  
Reverse, 256 Color, 8 Color, 4bit Grayscale  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern / Image processing function)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
158  
   
Imprinter (Endorser):  
With Imprinter option  
(Reverse side, minimum left margin printing position of 5mm)1  
Maximum number of characters to be printed: 40 characters  
Counter display range: 0 to 99999 (at 5 digits display)  
0 to 16777215 (at 8 digits display)  
Direction(Printing): Top to Bottom  
Font (orientation) : Vertical / Horizontal  
Bold font : Enabled  
Interface:  
SCSI-II, USB 2.0  
Enabled (at Flat bed scanning only)  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check overlapping / length)  
Enabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression): Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option: Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
1
If 0 mm is specified as the printing position, printing will begin 5 mm from the edge of the page.  
159  
 
Product:  
fi-5750C  
Type:  
Desktop  
Image sensor:  
Operating method:  
Color CCD + Reduced optical system  
Document fixed Flat bed(FB), Automatic Document  
Feed(ADF), Simultaneous double-sided scanning  
Long page scanning (305mm x 864mm)  
Fluorescent tube (White)  
Light source:  
Basic resolution:  
Output resolution:  
600 dpi  
Standard: 50 dpi to 600 dpi (at steps of 1dpi)  
Grayscale levels (internal): 10 bit 1024 levels  
Grayscale output:  
Halftone Patterns:  
Color output  
Enabled (8 bits)  
Dither matrix (can be downloaded), Error diffusion  
Enabled (24bit)  
Flat bed scanning speed:  
B/W : 0.9 sec or less (200 dpi, A4)  
Color : 0.9 sec or less (200 dpi, A4)  
ADF scanning speed 1:  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 55 pages per minute (200 dpi, A4, 55kg)  
(=110 screens per minute)  
Color  
Single sided: 55 pages per minute (200 dpi, A4, 55 kg)  
Double sided: 55 pages per minute (200 dpi, A4, 55kg)  
(=110 screens per minute)  
ADF paper chute capacity:  
Maximum 200 sheets, ream weight: 80 kg, A4 [High quality  
paper, normal temperature and humidity])  
Document size:  
Minimam 53mm x 74mm, Maximum 297 mm x 432 mm  
Supported regular paper 2:  
A3, A4/A4 Landscape, A5/A5 Landscape, A6/A6 Landscape, B4,  
B5/B5 Landscape, B6/B6 Landscape, Letter/Letter Landscape,  
Double Letter, Legal, US Executive/US Executive Landscape  
Isolation specification:  
Specified (one location)  
Background compensation: Enabled  
Brightness / Threshold / Contrast : 255 steps  
High light / Shadow :  
Gamma pattern:  
255 steps (at Color / Grayscale scanning)  
3 internal types (can be downloaded)  
1
2
This speed is only specified for the scanner itself. The actual reading speed may vary depending on the  
system configuration.  
Not all paper sizes can be used in all devices. For details, refer to the users' manual for the device.  
For other paper sizes, the customer settings can be used.  
160  
   
Image processing function: Simplified Dynamic Threshold (SDTC), Edge emphasis,  
Edge extraction, De-Screen, SEE(Selectable Edge Enhancement),  
Reverse, 256 Color, 8 Color, 4bit Grayscale  
Individual setting:  
Enabled (Brightness / Threshold / Contrast / High light /  
Shadow / Gamma pattern / Image processing function)  
Interface:  
SCSI-II, USB 2.0  
Enabled (at Flat bed scanning only)  
Enabled  
Preview:  
Flip Side Rotation:  
Rotation:  
Enabled  
Automatic Size and Skew detection: End of Page Detection, Automatic Page Size Detection,  
Black Background  
Overscan:  
Enabled  
Buffer scan ([Use Memory on Scanner]) function: Enabled  
Use Both Memory ( [Ram Cache]+[Use Memory on Scanner] ) function: Enabled  
Batch Detection:  
Multifeed detection:  
Pre-Pick:  
Enabled  
Enabled (Check overlapping / length)  
Enabled  
Check Over-skew:  
Blank page skip:  
Disabled  
Enabled (when [Ram cache] or [Use Both Memory] is used)  
JPEG Transfer (Hardware Compression) : Enabled  
Filter:  
Page Edge Filler, Digital Endorser  
Drop out color:  
sRGB output :  
Enabled  
Enabled  
Use Image Processing Software Option: Enabled  
Use of FUJITSU Scanner Control Center: Enabled  
161  
9.2. Maintenance Service  
This section explains briefly how you can help us to provide you with high-quality maintenance  
service.  
Since it is practically impossible for the Fujitsu service staff to be aware of every detail of your  
daily scanning operation, please understand that our staff may sometimes be unable to answer  
your question immediately. To help us in our effort to provide you with the best maintenance  
service possible, we ask you to kindly write down the following items (as many as possible):  
Serial number, version, and date, etc., of this product  
Name and product number of the image scanner being used  
The options installed on the image scanner being used  
Manufacturer, product name, and type number of the computer being used  
Manufacturer and version of the Windows® OS (whether Windows® has been updated)  
Name and version of the display driver  
Name and version of the printer driver  
Resolution (1024 x 768), number of colors, and number of dots (or points) of the screen  
Product name of the SCSI adapter, and name and version of the SCSI driver  
Error occurrence processing (the simpler the processing, the easier it is to determine the  
cause.)  
Also, we would appreciate it very much if you could kindly verify the following items prior to  
receiving our maintenance service;  
Is the power turned on?  
Is the cable connected correctly?  
Is the correct image scanner driver selected?  
162  
 
FUJITSU TWAIN32 Scanner Driver / Utility  
“Scanner Utility for Microsoft® Windows®”  
User’s Guide  
32 bit version  
First Edition July 2005  
2nd Edition August 2005  
3rd Edition November 2005  
4th Edition May 2006  
5th Edition June 2006  
6th Edition June 2006  
7th Edition July 2006  
All Rights Reserved, Copyright © PFU LIMITED 2006  
The contents of this document may change for improvements without  
prior notice.  
PFU LIMITED takes no responsibilities for infringements of third  
parties’ patents or other rights that may stem from the use of the data in  
this document.  
Unauthorized reproduction of this document is prohibited  

Trion T6002 User Manual
Sanyo Ch1852 User Manual
Samsung As18cm1n User Manual
Samsung As12sggb User Manual
Panasonic Cs Ce12gkew User Manual
LG 50UH5500 02 User Manual
HITACHI 42PD580DTA User Manual
FUJITSU LIFEBOOK P701 03 User Manual
ASUS X01AD ZB633KL User Manual
ASUS VH232T User Manual