D LINK DES 1016R DES 1016RPLUS User Manual

DES-1016R+/DES-1024R+  
10/100 Fast Ethernet Switch  
User’s Guide  
First Edition (February 2001)  
6DES1016R+01  
Printed In Taiwan  
RECYCLABLE  
Limited Warranty  
Hardware:  
D-Link warrants each of its hardware products to be free from defects in workmanship and materials  
under normal use and service for a period commencing on the date of purchase from D-Link or its  
Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D-  
Link Branch Office nearest to the place of purchase.  
This Warranty applies on the condition that the product Registration Card is filled out and returned  
to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back  
of this manual, together with a copy of the Registration Card.  
If the product proves defective within the applicable warranty period, D-Link will provide repair or  
replacement of the product. D-Link shall have the sole discretion whether to repair or replace, and  
replacement product may be new or reconditioned. Replacement product shall be of equivalent or  
better specifications, relative to the defective product, but need not be identical. Any product or  
part repaired by D-Link pursuant to this warranty shall have a warranty period of not less than 90  
days, from date of such repair, irrespective of any earlier expiration of original warranty period.  
When D-Link provides replacement, then the defective product becomes the property of D-Link.  
Warranty service may be obtained by contacting a D-Link office within the applicable warranty  
period, and requesting a Return Material Authorization (RMA) number. If a Registration Card for  
the product in question has not been returned to D-Link, then a proof of purchase (such as a copy of  
the dated purchase invoice) must be provided. If Purchaser's circumstances require special handling  
of warranty correction, then at the time of requesting RMA number, Purchaser may also propose  
special procedure as may be suitable to the case.  
After an RMA number is issued, the defective product must be packaged securely in the original or  
other suitable shipping package to ensure that it will not be damaged in transit, and the RMA  
number must be prominently marked on the outside of the package. The package must be mailed or  
otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never  
be responsible for any software, firmware, information, or memory data of Purchaser contained in,  
stored on, or integrated with any product returned to D-Link pursuant to this warranty.  
Any package returned to D-Link without an RMA number will be rejected and shipped back to  
Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a reasonable  
handling charge in addition mailing or shipping costs.  
Software:  
Warranty service for software products may be obtained by contacting a D-Link office within the  
applicable warranty period. A list of D-Link offices is provided at the back of this manual, together  
with a copy of the Registration Card. If a Registration Card for the product in question has not been  
returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice)  
must be provided when requesting warranty service. The term "purchase" in this software warranty  
refers to the purchase transaction and resulting license to use such software.  
D-Link warrants that its software products will perform in substantial conformance with the  
applicable product documentation provided by D-Link with such software product, for a period of  
ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link warrants  
the magnetic media, on which D-Link provides its software product, against failure during the same  
warranty period. This warranty applies to purchased software, and to replacement software  
provided by D-Link pursuant to this warranty, but shall not apply to any update or replacement  
which may be provided for download via the Internet, or to any update which may otherwise be  
provided free of charge.  
D-Link's sole obligation under this software warranty shall be to replace any defective software  
product with product which substantially conforms to D-Link's applicable product documentation.  
Purchaser assumes responsibility for the selection of appropriate application and system/platform  
software and associated reference materials. D-Link makes no warranty that its software products  
will work in combination with any hardware, or any application or system/platform software product  
provided by any third party, excepting only such products as are expressly represented, in D-Link's  
applicable product documentation as being compatible. D-Link's obligation under this warranty shall  
be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide  
compatibility when there is fault in the third-party hardware or software. D-Link makes no  
warranty that operation of its software products will be uninterrupted or absolutely error-free, and  
no warranty that all defects in the software product, within or without the scope of D-Link's  
applicable product documentation, will be corrected.  
Warranty Period  
For warranty in your region, please check with your local D-Link office and authorized agents as  
warranty periods may vary from region to region.  
The warranty for power supplies and power adapters is one year.  
D-Link Offices for Registration and Warranty Service  
The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office.  
To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty  
service as to a software product, contact the D-Link office nearest you. An address/telephone/fax/e-  
mail/Web site list of D-Link offices is provided in the back of this manual.  
Limitation of Warranties  
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S  
SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE  
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF  
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY  
OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE  
SALE, INSTALLATION MAINTENANCE OR USE OF D-LINK'S PRODUCTS  
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND  
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST  
OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,  
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY  
OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,  
LIGHTNING OR OTHER HAZARD.  
Limitation of Liability  
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA,  
LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR  
INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE,  
PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED  
AND ON ANY THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT  
ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  
Trademarks  
Copyright ã 2001 D-Link Corporation. Contents subject to change without prior notice. D-Link is a  
registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to  
their respective proprietors.  
Copyright Statement  
No part of this publication may be reproduced in any form or by any means or used to make any  
derivative such as translation, transformation, or adaptation without permission from D-Link  
Corporation/D-Link Systems Inc., as stipulated by the United States Copyright Act of 1976.  
FCC Warning  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with this user’ s guide, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which  
case the user will be required to correct the interference at his own expense.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
CE Mark Warning  
This is a Class A product. In a domestic environment this product may cause radio interference in  
which case the user may be required to take adequate measures.  
Warnung!  
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen.  
In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.  
Precaución!  
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en  
cuyo case, puede requerirse al usuario para que adopte las medidas adecuadas.  
Attention!  
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des  
interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.  
Attenzione!  
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può  
causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti  
adeguati.  
VCCI Warning  
BSMI Warning  
10/100 Fast Ethernet Switch User’ s Guide  
1
0 FEATURES  
¨
16 or 24 UTP ports all come with NWay auto-negotiation and operate  
at 10/100 Mbps for connection to servers and hubs. All ports can  
auto-negotiate for full or half-duplex operation.  
¨
¨
¨
¨
¨
¨
¨
¨
All ports support auto MDI/MDIX, so there is no need to use cross-  
over cables or an up-link port.  
Store-and-forward switching scheme capability to support rate  
adaptation and ensure data integrity.  
Auto-polarity detection for correction of incorrect polarity on the  
receive twisted pair at each port.  
Data forwarding rate 148,800 pps per port at 100% of wire-speed  
for 100Mbps speed.  
Data forwarding rate 14,880 pps per port at 100% of wire-speed  
for 10Mbps speed.  
Data filtering rate eliminates all error packets, runts, etc. at  
148,800 pps per port at 100% of wire-speed for 100Mbps speed.  
Data filtering rate eliminates all error packets, runts, etc. at  
14,880 pps per port at 100% of wire-speed for 10Mbps speed.  
Up to 4K unicast address entities per device, self-learning, and  
table aging.  
¨
¨
256K Byte-on-Chip packet buffer per eight ports.  
All 16 or 24 UTP ports support IEEE802.3x flow control for full  
duplex and backpressure flow control for half duplex.  
¨
Optional two-port Fiber module (SC type connector) in the front  
panel for length extension. These two ports operate at either 100M  
1
10/100 Fast Ethernet Switch User’ s Guide  
full duplex or half duplex by means of a manual setting. Please  
see Chapter Two for additional information about module settings.  
2
10/100 Fast Ethernet Switch User’ s Guide  
2
1 UNPACKING AND SETUP  
Unpacking  
Open the shipping carton of the Switch and carefully unpack its  
contents. The carton should contain the following items:  
¨
¨
¨
¨
¨
One DES-1016R+ or DES-1024R+ 10/100 Fast Ethernet Switch  
One AC power cord  
This User’ s Guide  
Four rubber feet with adhesive backing  
Screws and two L-type brackets for rack mounting  
If any item is found missing or damaged, please contact your local  
D-Link reseller for replacement.  
Setup  
The setup of the Switch can be performed using the following steps:  
¨
¨
The surface must support at least 3 kg for the Switch.  
The power outlet should be within 1.82 meters (6 feet) of the  
device.  
¨
¨
Visually inspect the power cord and see that it is fully secured to  
the AC power connector.  
Make sure that there is proper heat dissipation from and  
adequate ventilation around the Switch. Do not place heavy  
objects on the Switch.  
3
10/100 Fast Ethernet Switch User’ s Guide  
Desktop or Shelf Installation  
When installing the Switch on a desktop or shelf, the rubber feet  
included with the device must be first attached. Attach these cushioning  
feet on the bottom at each corner of the device. Allow enough ventilation  
space between the device and the objects around it.  
Figure 2.1 10/100 Fast Ethernet Switch installed on a Desktop or  
Shelf  
Rack Installation  
The Switch can be mounted in an EIA standard size, 19-inch rack,  
which can be placed in a wiring closet with other equipment. To install,  
attach the mounting brackets on the switch’ s front panel (one on each  
side) and secure them with the screws provided.  
4
10/100 Fast Ethernet Switch User’ s Guide  
Figure 2.2 Attaching the mounting brackets to the 10/100 Fast  
Ethernet Switch  
Then, use the screws provided with the equipment rack to mount the  
Switch in the rack.  
Module Installation  
An optional two-port fiber module (SC type connector) can be installed in  
the front panel. Follow these steps:  
First, set up the module, adjusting the jumper settings as desired. The  
default setting is full duplex.  
Figure 2.3 Jumper settings on the module  
5
10/100 Fast Ethernet Switch User’ s Guide  
Next, make sure that the device is powered off and then remove the  
plain bracket on the front of the switch.  
Figure 2.4 Removing the plain bracket  
After removing the plain bracket, slide the module in the guide rails all  
the way into the slot and secure the screws.  
Figure 2.5 Sliding the module into position  
When properly installed, the Slot LED will be lit after powering on the  
Switch (see Chapter 3 for more information about LEDs, including a  
diagram).  
Note: Always remember to turn off the power before a module is inserted  
or removed.  
6
10/100 Fast Ethernet Switch User’ s Guide  
3
2 IDENTIFYING EXTERNAL  
COMPONENTS  
Front Panel  
The front panel of the Switch consists of 16 (DES-1016R+) or 24  
(DES-1024R+) 10/100 Mbps MDI-II/MDI-X ports and LED indicators.  
Figure 3.1 Front panel view of the DES-1024R+ Switch  
Rear Panel  
The rear panel of the Switch consists of an AC power connector.  
Figure 3.2 Rear panel view of the DES-1024R+ switch  
¨
AC Power Connector This is a three-pronged connector that  
supports the power cord. Plug in the female connector of the  
provided power cord into this connector, and the male into a  
power outlet. Supported input voltages range from 100 ~ 240 VAC  
at 50 ~ 60 Hz.  
7
10/100 Fast Ethernet Switch User’ s Guide  
LED Indicators  
The LED indicators of the Switch include Power, 100M, Link/Act  
(Link/Activity), and Slot. The LED indicators are used to facilitate  
monitoring and troubleshooting of the Switch. The following shows the  
LED indicators for the Switch along with an explanation of each  
indicator.  
Figure 3.3 The DES-1024R+ Switch LED indicators  
¨
¨
¨
Power This indicator operates when the Switch is turned on. If  
this indicator is not lit, check the AC power connector to ensure  
proper insertion of the power cord.  
100M The LED indicator lights green when a 100 Mbps device is  
connected to a respective port. If a 10 Mbps device is connected to  
a respective port, the LED indicator is OFF.  
Link/Act These LED indicators are lighted green when there is  
a secure connection (or link) to a device at any of the ports. The  
LED indicators blink green whenever there is reception or  
transmission (i.e. ActivityAct) of data occurring at a port.  
¨
Slot This LED indicator is lighted green when there is a secure  
connection (or link) to an optional two-port 100BASE-FX (SC type)  
module is installed in the front panel. Each port has its own LED,  
designated as I and II. See 100M and Link/Act indicator  
descriptions above for further information.  
8
A
3 TECHNICAL SPECIFICATIONS  
General  
10BASE-T:  
Network Cabling:  
2-pair UTP Cat. 3, 4, 5 (100m)  
EIA/TIA- 568 100-ohm STP (100m)  
100BASE-TX:  
2-pair UTP Cat. 5 (100m)  
EIA/TIA-568 100-ohm STP (100m)  
100BASE-FX:  
Multi-mode (62.5/125µm or 50/125µm fiber cabling with SC  
connector  
Number of Ports:  
DES-1016R+: 16 x 10/100 Mbps ports  
DES-1024R+: 24 x 10/100 Mbps ports  
DES-102F: 2 x 100BASE-FX ports  
Physical and Environmental  
AC inputs:  
100 - 240 VAC, 50/60 Hz (internal universal power supply)  
Power Consumption: 39 watts maximum  
Operating  
Temperature:  
32 ° ~ 122 °F (0 ° ~ 50 °C)  
-13 ° ~ 131 °F (-25 ° ~ 5 5 °C)  
5% ~ 95% non-condensing  
Storage  
Temperature:  
Humidity:  
EMI:  
FCC Class A, CE Mark Class A, VCCI Class A,  
BSMI Class A , C-Tick Class A  
Safety:  
UL (UL 1950), CSA (CSA950), TUV/GS (EN60950)  
DC Fan:  
One built-in 40 x 40 x 10 mm DC fan  
Dimensions:  
Weight:  
441 x 207 x 44 mm (IU), 19-inch rack-mount width  
DES-1016R+: 2.6 kg & DES-1024R+: 2.7 kg  
Offices  
AUSTRALIA  
CANADA  
D-LINK AUSTRALASIA  
Unit 16, 390 Eastern Valley Way Roseville, NSW 2069 Australia  
TEL: 61-2-9417-7100 FAX: 61-2-9417-1077  
TOLL FREE (Australia): 1800 177 100 TOLL FREE (New Zealand): 0800-900900  
D-LINK CANADA  
2180 Winston Park Drive, Oakville, Ontario, L6H 5W1 Canada  
TEL: 1-905-829-5033 FAX: 1-905-829-5223 BBS: 1-965-279-8732  
TOLL FREE: 1-800-354-6522 URL: www.dlink.ca  
FTP: ftp.dlinknet.com E-MAIL: [email protected]  
DENMARK  
EGYPT  
D-LINK DENMARK  
Naverland 2 DK-2600 Glostrup Copenhagen, Denmark  
TEL:45-43-969040 FAX:45-43-424347 URL: www.dlink.dk E-MAIL: [email protected]  
D-LINK MIDDLE EAST  
7 Assem Ben Sabet Street, Heliopolis Cairo, Egypt  
TEL: 202-245-6176 FAX: 202-245-6192 URL: www.dlink-me.com  
FRANCE  
D-LINK FRANCE  
Le Florilege #2, Allee de la Fresnerie, 78330 Fontenay le Fleury, France  
TEL: 33-1-3023-8688 FAX: 33-1-3023-8689 URL: www.dlink-france.com  
GERMANY  
D-LINK CENTRAL EUROPE/D-LINK GERMANY  
Schwalbacher Strasse 74, 65760 Eschborn, Germany  
TEL: 49-(0)6196-7799-0 FAX: 49-(0)6196-7799-300 URL: www.dlink.de  
BBS: 49-(0)6192-971199 (analog)  
BBS: 49-(0)6192-971198 (ISDN)  
INFO: 00800-7250-0000 (toll free) HELP: 00800-7250-4000 (toll free)  
REPAIR: 00800-7250-8000 E-MAIL: [email protected] & [email protected]  
INDIA  
D-LINK INDIA  
Plot No.5, Kurla-Bandra Complex Rd., Off Cst Rd., Santacruz (E)  
Bombay - 400 098 India  
TEL: 91-22-652-6696 FAX: 91-22-652-8914 URL: www.dlink-india.com  
ITALY  
D-LINK ITALY  
Via Nino Bonnet n.6/b, 20154 Milano, Italy  
TEL: 39-02-2900-0676 FAX: 39-02-2900-1723 URL: www.dlink.it  
JAPAN  
D-LINK TOKYO  
10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan  
TEL: 81-3-5434-9678 FAX: 81-3-5434-9868 URL: www.d-link.co.jp  
SINGAPORE  
D-LINK INTERNATIONAL/D-LINK SINGAPORE  
1 International Business Park, #03-12 The Synergy, Singapore 609917  
TEL : 65-774-6233 FAX: 65-774-6322 E-MAIL: [email protected]  
SWEDEN  
TAIWAN  
D-LINK SWEDEN  
P. O. Box 15036, S-167 15 Bromma, Sweden  
TEL: 46-(0)8564-61900 FAX: 46-(0)8564-61901 E-MAIL: [email protected] URL: www.dlink.dk  
D-LINK TAIWAN  
2F, No. 119 Pao-Chung Rd, Hsin-Tien, Taipei, Taiwan  
TEL: 886-2-2910-2626 FAX: 886-2-2910-1515 URL: www.dlinktw.com.tw  
U.K.  
D-LINK EUROPE/D-LINK U.K.  
4th Floor, Merit House, Edgeware Road, Colindale, London NW9 5AB U.K.  
TEL: 44 (0) 20-8731-5555 FAX: 44 (0) 20-8731-5511 URL: www.dlink.co.uk  
U.S.A.  
D-LINK U.S.A.  
53 Discovery Drive, Irvine, CA 92618, USA  
TEL: 1-949-788-0805 FAX: 1-949-753-7033 BBS: 1-949-455-1779 & 1-949-455-9616  
INFO: 1-800-326-1688 URL: www.dlink.com  
Registration Card  
Print, type or use block letters.  
Your name: Mr./Ms  
_____________________________________________________________________________  
Organization: ________________________________________________  
Dept. ____________________________  
Your title at organization:  
Telephone:  
Organization's full address:  
________________________________________________________________________  
_______________________________________ Fax:________________________________________  
______________________________________________________________________  
____________________________________________________________________________________________  
_____________________________________________________________________________________  
Country:  
Date of purchase (Month/Day/Year):  
_______________________________________________________________  
Product Model  
Product Serial No.  
* Product installed in type of  
computer (e.g., Compaq 486)  
* Product installed in  
computer serial No.  
(* Applies to adapters only)  
Product was purchased from:  
Reseller's name:  
______________________________________________________________________________  
Telephone:  
_______________________________________ Fax:________________________________________  
_________________________________________________________________________  
_________________________________________________________________________  
_________________________________________________________________________  
Reseller's full address:  
Answers to the following questions help us to support your product:  
1. Where and how will the product primarily be used?  
oHome oOffice oTravel oCompany Business oHome Business oPersonal Use  
2. How many employees work at installation site?  
o1 employee o2-9 o10-49 o50-99 o100-499 o500-999 o1000 or more  
3. What network protocol(s) does your organization use ?  
oXNS/IPX oTCP/IP oDECnet oOthers_____________________________  
4. What network operating system(s) does your organization use ?  
oD-Link LANsmart oNovell NetWare oNetWare Lite oSCO Unix/Xenix oPC NFS o3Com 3+Open  
oBanyan Vines oDECnet Pathwork oWindows NT oWindows NTAS oWindows '95  
oOthers__________________________________________  
5. What network management program does your organization use ?  
oD-View oHP OpenView/Windows oHP OpenView/Unix oSunNet Manager oNovell NMS  
oNetView 6000 oOthers________________________________________  
6. What network medium/media does your organization use ?  
oFiber-optics oThick coax Ethernet oThin coax Ethernet o10BASE-T UTP/STP  
o100BASE-TX o100BASE-T4 o100VGAnyLAN oOthers_________________  
7. What applications are used on your network?  
oDesktop publishing oSpreadsheet oWord processing oCAD/CAM  
oDatabase management oAccounting oOthers_____________________  
8. What category best describes your company?  
oAerospace oEngineering oEducation oFinance oHospital oLegal oInsurance/Real Estate oManufacturing  
oRetail/Chainstore/Wholesale oGovernment oTransportation/Utilities/Communication oVAR  
oSystem house/company oOther________________________________  
9. Would you recommend your D-Link product to a friend?  
oYes oNo oDon't know yet  
10.Your comments on this product?  
__________________________________________________________________________________________  

Troy Bilt Air Conditioner Mxz 3a30na User Manual
Sunpentown Intl Wa 1400e User Manual
Samsung Aw09l1 Series User Manual
Philips Steriliser Scf225 User Manual
Motorola Mbp8 User Manual
Garrison Digital Oil Heater User Manual
Crystal Vision Cvt9604e 3010w User User Manual
BROTHER FAX 560 User Manual
BLACK DECKER HHVJ315JD User Manual
BLACK DECKER GH900 User Manual