BLACK DECKER NV3610N User Manual

NV3610N  
NV7210N  
NV9610N  
D
E
F
3
(Original instructions)  
ENGLISH  
Intended use  
Your BLACK+DECKERTM Dustbuster® handheld vacuum cleaner has been designed  
for light dry vacuum cleaning purposes. This appliance is intended for household use  
only.  
Safety instructions  
Warning! Read all safety warnings  
@
and all instructions.Failure to follow the  
warnings and instructions listed below may result  
in electric shock, fire and/or serious injury.  
Warning!When using battery-powered ap-  
@
pliances, basic safety precautions, including the  
following, should always be followed to reduce  
the risk of fire, leaking batteries, personal injury  
and material damage.  
u
u
Read all of this manual carefully before using the appli-  
ance.  
The intended use is described in this manual. The use  
of any accessory or attachment or the performance  
of any operation with this appliance other than those  
recommended in this instruction manual may present a  
risk of personal injury.  
u
Retain this manual for future reference.  
Using your appliance  
u
Do not use the appliance to pick up liquids or any mate-  
rials that could catch fire.  
u
u
u
Do not use the appliance near water.  
Do not immerse the appliance in water.  
Never pull the charger lead to disconnect the charger  
from the socket. Keep the charger lead away from heat,  
oil and sharp edges.  
4
(Original instructions)  
ENGLISH  
u
This appliance can be used by children aged from 8  
years and above and persons with reduced physical,  
sensory or mental capabilities or lack of experience and  
knowledge if they have been given supervision or in-  
struction concerning use of the appliance in a safe way  
and understand the hazards involved. Children shall not  
play with the appliance. Cleaning and user maintenance  
shall not be made by children without supervision.  
InBsepfoercetuisoen, cahencdk threepapapilriasnce for damaged or defec-  
u
tive parts. Check for breakage of parts, damage to  
switches and any other conditions that may affect its  
operation.  
u
u
u
u
Do not use the appliance if any part is damaged or  
defective.  
Have any damaged or defective parts repaired or  
replaced by an authorized repair agent.  
Regularly check the charger lead for damage. Replace  
the charger if the lead is damaged or defective.  
Never attempt to remove or replace any parts other  
than those specified in this manual.  
Additional safety instructions  
Residual risks.  
Additional residual risks may arise when using the  
tool which may not be included in the enclosed  
safety warnings. These risks can arise from mis-  
use, prolonged use etc.  
Even with the application of the relevant safety  
regulations and the implementation of safety  
devices, certain residual risks can not be avoided.  
These include:  
u
u
u
Injuries caused by touching any moving parts.  
Injuries caused by touching any hot parts.  
Injuries caused when changing any parts or accesso-  
ries.  
5
(Original instructions)  
ENGLISH  
u
Injuries caused by prolonged use of the appliance.  
When using any appliance for prolonged periods ensure  
you take regular breaks.  
Batteries and chargers  
Batteries  
u
u
u
u
Never attempt to open for any reason.  
Do not expose the battery to water.  
Do not expose the battery to heat.  
Do not store in locations where the temperature may  
exceed 40°C.  
u
u
Charge only at ambient temperatures between 10°C  
and 40°C.  
Charge only using the charger provided with the appli-  
ance/tool. Using the wrong charger could result in an  
electric shock or overheating of the battery.  
When disposing of batteries, follow the instructions  
given in the section "Protecting the environment".  
Do not damage/deform the battery pack either by punc-  
ture or impact, as this may create a risk of injury and  
fire.  
u
u
u
u
Do not charge damaged batteries.  
Under extreme conditions, battery leakage may occur.  
When you notice liquid on the batteries carefully wipe  
the liquid off using a cloth. Avoid skin contact.  
In case of skin or eye contact, follow the instructions  
u
Wbaerlnowin. g!The battery fluid may cause personal injury  
or damage to property. In case of skin contact, immediate-  
ly rinse with water. If redness, pain or irritation occurs seek  
medical attention. In case of eye contact, rinse immedi-  
ately with clean water and seek medical attention.  
Chargers  
Your charger has been designed for a specific  
voltage. Always check that the mains voltage  
corresponds to the voltage on the rating plate and  
the information in the technical data table.  
6
(Original instructions)  
ENGLISH  
Warning!Never attempt to replace the charger unit  
with a regular mains plug.  
u
Use your BLACK+DECKER charger only to charge the  
battery in the appliance/tool with which it was supplied.  
Other batteries could burst, causing personal injury and  
damage.  
u
u
Never attempt to charge nonrechargeable batteries.  
If the supply cord is damaged, it must be replaced by  
the manufacturer or an authorised Black & Decker  
Service Centre in order to avoid a hazard.  
Do not expose the charger to water.  
u
u
u
u
Do not open the charger.  
Do not probe the charger.  
The appliance/tool/battery must be placed in a well  
ventilated area when charging.  
Electrical safety  
Your charger has been designed for a specific  
voltage. Always check that the mains voltage cor-  
responds to the voltage on the rating plate. Never  
attempt to replace the charger unit with a regular  
mains plug.  
Symbols on the charger  
Read all of this manual carefully before using the  
appliance.  
This tool is double insulated; therefore no earth  
#
wire is required. Always check that the power  
supply corresponds to the voltage on the rating  
plate.  
Short circuit proof safety isolating transformer.  
The mains supply is electrically separated from  
the transformer output.  
w
7
(Original instructions)  
ENGLISH  
The charger automatically shuts off if the ambi-  
ent temperature becomes too high. As a con-  
sequence the charger will be inoperable. The  
charging base must be disconnected from the  
mains supply and taken to an authorised service  
centre for repair.  
x
The charging base is intended for indoor use  
only.  
$
Features  
This tool includes some or all of the following features.  
1. On/off switch  
2. Bowl release button  
3. Dust bowl  
4. Charger  
5. Charging bracket  
Fig. A  
6. Dry pick up cloth filter  
7. Pre-filter  
Installation  
Wall Mounting (fig. B)  
The product can be attached to a wall to provide a convenient storage and charging  
point for the appliance.  
When fixing to a wall, make sure that the fixing method is suitable for the wall type and  
is appropriate to the weight of the appliance.  
u Mark the location of the screw holes (within reach of an electrical outlet for charging  
the vac while it is on the wall bracket).  
u Fix the mounting bracket to the wall using appropriate screws and plugs for the type  
of wall and weight of the appliance.  
u Hang the appliance on the wall by placing the opening on the base of the vac over  
the hooks in the wall mount charging bracket.  
Use  
u Before first use, the battery must be charged for at least 24 hours.  
u Place the appliance on the charging bracket whenever it is not in use.  
Charging the battery (Fig. B)  
u Make sure that the appliance is switched off. The battery will not be charged with  
the on/off switch in the on position.  
u Place the appliance on the charging bracket (5).  
u Plug in the charger. Switch on at the mains.  
u Leave the appliance to charge for at least 21 hours.  
8
(Original instructions)  
ENGLISH  
While charging, the charger may become warm. This is normal and does not indicate a  
problem. The appliance can be left connected to the charger indefinitely.  
Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40  
°C.  
Note: Ensure the appliance is fully seated onto the charging base. If the appliance is  
not fully seated then the appliance will not charge.  
Switching on and off (fig. C)  
u To switch the appliance on, slide the on/off switch (1) forward to position 1.  
u To switch the appliance off, slide the on/off switch (1) back to position 0.  
Optimising the suction force  
In order to keep the suction force optimised, the filters must be cleared regularly during  
use.  
Emptying and cleaning the product.  
Removing the dust bowl and filters (fig. D & E).  
Warning! The filters are re-usable and should be cleaned regularly.  
u Press the bowl release button (2) and pull the dust bowl (3) straight off.  
u While holding the dust bowl over a bin or sink, pull out the filter to empty the con-  
tents of the bowl.  
u To replace the dust bowl, place it back onto the handle until it “clicks” firmly into  
position.  
Warning! Never use the appliance without the filters. Optimum dust collection will only  
be achieved with clean filters.  
Pre-filter (fig. F)  
The Filter and pre-filter can be separated to allow better cleaning.  
u Twist the pre-filter (7) in an anti-clockwise direction and lift from the filter (6).  
Cleaning the dust bowls and filters  
u The dust bowls and filters can be washed in warm soapy water.  
u Make sure that the filters and the dust bowl are dry before re-fitting.  
Replacing the filters  
The filters should be replaced every 6 to 9 months and whenever worn or damaged.  
Replacement filters are available from your Black & Decker dealer:  
For models: NV3610N, NV7210N & NV9610N use filter part number FLVD10-XJ  
Maintenance  
Your BLACK+DECKER corded/cordless appliance/tool has been designed to operate  
over a long period of time with a minimum of maintenance. Continuous satisfactory  
operation depends upon proper tool care and regular cleaning.  
Warning! Before performing any maintenance on corded/ cordless power tools:  
u Switch off and unplug the appliance/tool.  
u Or switch off and remove the battery from the appliance/tool if the appliance/tool  
has a separate battery pack.  
u Or run the battery down completely if it is integral and then switch off.  
u Unplug the charger before cleaning it. Your charger does not require any mainte-  
nance apart from regular cleaning.  
u Regularly clean the ventilation slots in your appliance/tool/charger using a soft  
brush or dry cloth.  
9
(Original instructions)  
ENGLISH  
u Regularly clean the motor housing using a damp cloth. Do not use any abrasive or  
solvent-based cleaner.  
Protecting the environment  
Separate collection. This product must not be disposed of with normal house-  
Z
hold waste.  
Should you find one day that your BLACK+DECKER product needs replacement, or if it  
is of no further use to you, do not dispose of it with household waste. Make this product  
available for separate collection.  
Separate collection of used products and packaging allows materials to be  
z
recycled and used again. Re-use of recycled materials helps prevent environ-  
mental pollution and reduces the demand for raw materials.  
Local regulations may provide for separate collection of electrical products from the  
household, at municipal waste sites or by the retailer when you purchase a new  
product.  
Black & Decker provides a facility for the collection and recycling of BLACK+DECKER  
products once they have reached the end of their working life. To take advantage of this  
service please return your product to any authorised repair agent who will collect them  
on our behalf.  
You can check the location of your nearest authorised repair agent by contacting your  
local Black & Decker office at the address indicated in this manual. Alternatively, a list  
of authorisedBlack & Decker repair agents and full details of our after-sales service and  
Battery  
If you want to dispose of the product yourself, the battery must be removed as  
Z
described below and disposed of in accordance with local regulations.  
u Preferably discharge the battery by operating the appliance until the motor stops.  
u Press the bowl release button (2) and remove the dust bowl (3).  
u Remove the five screws holding the body of the appliance together.  
u Lift the housing cover away from the assembly.  
u Detach all lead connections from the battery pack.  
u Remove battery pack and motor assembly.  
u Place the battery pack and motor assembly in suitable packaging to ensure that the  
terminals cannot be short-circuited.  
u Take the battery pack and motor assembly to your service agent or to a local  
recycling station.  
Once removed, the battery cannot be refitted.  
10  
(Original instructions)  
ENGLISH  
Technical data  
NV3610N  
NV7210N  
NV9610N  
(H1)  
(H1)  
(H1)  
Voltage  
Battery  
Weight  
Charger  
Vdc  
3.6  
7.2  
9.6  
Type  
kg  
NiMH  
0.74  
NiMH  
0.86  
NiMH  
0.92  
VA050020D  
BA050020D  
SSC-180008EU  
SSC-180008UK  
SSC-180008EU  
SSC-180008UK  
Input voltage  
Vac  
230  
5ac  
100-240  
27dc  
100-240  
27dc  
Output voltage  
Current  
V
mA  
200  
14  
85  
21  
85  
21  
Approximate  
charge time  
h
Weight  
kg  
0.21  
0.06  
0.06  
Guarantee  
Black & Decker is confident of the quality of its products and offers an outstanding  
guarantee. This guarantee statement is in addition to and in no way prejudices your  
statutory rights. The guarantee is valid within the territories of the Member States of the  
European Union and the European Free Trade Area.  
If a Black & Decker product becomes defective due to faulty materials, workmanship  
or lack of conformity, within 24 months from the date of purchase, Black & Decker  
guarantees to replace defective parts, repair products subjected to fair wear and tear or  
replace such products to ensure minimum inconvenience to the customer unless:  
u The product has been used for trade, professional or hire purposes;  
u The product has been subjected to misuse or neglect;  
u The product has sustained damage through foreign objects, substances or ac-  
cidents;  
u Repairs have been attempted by persons other than authorised repair agents or  
Black & Decker service staff.  
To claim on the guarantee, you will need to submit proof of purchase to the seller or an  
authorised repair agent. You can check the location of your nearest authorised repair  
agent by contacting your localBlack & Decker office at the address indicated in this  
manual. Alternatively, a list of authorised Black & Decker repair agents and full details  
of our after-sales service and contacts are available on the Internet at: www.2helpU.  
com  
Decker product and to be kept up to date on new products and special offers. Further  
information on the BLACK+DECKER brand and our range of products is available at  
11  
Australia  
Black & Decker (Australia) Pty. Ltd.  
20 Fletcher Road, Mooroolbark,  
Victoria, 3138  
Tel. 03-8720 5100  
Fax 03-9727 5940  
New Zealand  
Black & Decker  
5 Te Apunga Place  
Mt Wellington  
Tel. +64 9 259 1133  
Fax +64 9 259 1122  
Auckland 1060  
United Kingdom  
Black & Decker  
210 Bath Road  
Tel. 01753 511234  
Fax 01753 551155  
Slough, Berkshire SL1 3YD  
90610814 REV-0  
04/2014  

Windchaser Products Pacr12 User Manual
Sinclair Smf C09ai User Manual
Samsung E S F Db98 05586a User Manual
Panasonic Cu W7dkr User Manual
Oki B 4545 Mfp User Manual
Mitsubishi Electronics 8 User Manual
LG DLEX2650 User Manual
GE AHE50 User Manual
CRAFTSMAN 919.156730 User Manual
CRAFTSMAN 139.53629SRT User Manual