BD9:AꢁB&%&(ꢁ
*ꢂꢁMꢁ+ꢂꢁB:I6Aꢁ8JII>C<ꢁ
76C9H6L
DLC:GꢀHꢁB6CJ6A
ꢀ;DGꢁBD9:AHꢁB6CJ;68IJG:9ꢁH>C8:ꢁ+$%.ꢂ
E]dcZ/ꢁꢃ(+%ꢄꢁ,()"()-'ꢁ™ꢁDca^cZꢁIZX]c^XVaꢁHjeedgi/ꢁiZX]"hjeedgi5h]de[dm#W^o
8DENG><=Iꢁꢁ?6CJ6GN!ꢁ'%%*ꢁ7NꢁLDD9HID8@ꢁ>CI:GC6I>DC6A!ꢁ>C8#!ꢁG:K>H:9ꢁ6J<JHI!ꢁ'%%.ꢁꢃIHꢄ
L6GC>C</ꢁCDꢁEDGI>DCꢁD;ꢁI=>HꢁB6CJ6AꢁB6Nꢁ7:ꢁG:EGD9J8:9ꢁ>Cꢁ6CNꢁH=6E:ꢁDGꢁ;DGBꢁL>I=DJI
I=:ꢁLG>II:Cꢁ6EEGDK6AꢁD;ꢁLDD9HID8@ꢁ>CI:GC6I>DC6A!ꢁ>C8#
Eg^ciZYꢁ^cꢁ8]^cV
ꢅ+,(&8G
Download from Www.Somanuals.com. All Manuals Search And Download.
:fek\ekj
@EKIF;L:K@FEꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%)
D8@EK<E8E:<ꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% )-
General .......................................... 26
Cleaning ......................................... 26
Lubrication ...................................... 26
Woodstock Technical Support ..................2
Machine Specifications ..........................3
J8=<KPꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%-
Standard Machinery Safety .....................6
Additional Safety for
J<IM@:<ꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ).
General .......................................... 27
Blade Change ................................... 27
Blade Tracking .................................. 29
Electrical Safety Instructions................. 30
Wiring Diagram ................................. 31
Troubleshooting................................. 32
Metal Cutting Bandsaws.........................8
<C<:KI@:8Cꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%0
110V/220V Operation............................9
Extension Cords ..................................9
Electrical Specifications ........................9
G8IKJꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% *+
Motor & Feed Rate Control................... 34
Saw Assembly ................................... 36
Stand Assembly ................................. 38
Guides & Shafts ................................ 40
Machine Labels ................................. 42
J<KLGꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ('
Unpacking ....................................... 10
Inventory ........................................ 10
Machine Placement ............................ 11
Cleaning Machine............................... 11
Wheels, Feet, and Cabinet ................... 12
Shipping Strap Removal
N8II8EKPꢀ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% +,
& Stop Adjustment............................. 14
Squaring Vise to Blade ........................ 14
Chip Tray & Cast Iron Stop.................... 15
Automatic OFF Adjustment................... 16
Pulley Cover..................................... 17
Blade Tension ................................... 18
Blade Guides.................................... 19
Test Run.......................................... 20
FG<I8K@FEJ%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% )(
General .......................................... 21
Operation........................................ 21
Blade Speed..................................... 23
Blade Selection................................. 24
Feed Rate ....................................... 25
LJ<ꢀK?<ꢀHL@:Bꢀ>L@;<ꢀG8><ꢀC89<CJꢀKFꢀJ<8I:?ꢀFLKꢀ@E=FID8K@FEꢀ=8JKꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
@EKIF;L:K@FE
Nff[jkfZbꢀK\Z_e`ZXcꢀJlggfik
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: k\Z_$jlggfik7j_fg]fo%
Y`q. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you need the latest edition of this manual, you can download it from _kkg1&&nnn%j_fg]fo%Y`q.
If you have comments about this manual, please contact us at:
Nff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%
8kke1ꢀK\Z_e`ZXcꢀ;fZld\ekXk`feꢀDXeX^\i
G%F%ꢀ9foꢀ)*'0
9\cc`e^_Xd#ꢀN8ꢀ0/)).
<dX`c1ꢀdXelXcj7nff[jkfZb`ek%Zfd
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
B68=>C:ꢁ
HE:8>;>86I>DCH
BD9:AꢁB&%&(
*ꢂꢁMꢁ+ꢂꢁB:I6Aꢁ8JII>C<ꢁ76C9H6L
Dfkfi
Type..........................................................................................TEFC Capacitor Start Induction
Horsepower............................................................................................................... 1⁄2 HP
Voltage ................................................................................................................ 110/220V
Prewired.....................................................................................................................110V
Phase....................................................................................................................... Single
Amps.......................................................................................................................7/3.5A
Speed .................................................................................................................. 1725 RPM
Cycle........................................................................................................................60 Hz
Number Of Speeds............................................................................................................. 1
Power Transfer .................................................................................................... V-Belt Drive
Bearings ............................................................................................... Sealed and Lubricated
DX`eꢀJg\Z`]`ZXk`fej
Fg\iXk`feꢀ@e]f
Blade Speeds..........................................................................................80, 120, 200 FPM
Blade Length........................................................................................................641⁄2
"
Head Swivel ........................................................................................................... 45°
:lkk`e^ꢀ:XgXZ`k`\j
Angle Cuts.......................................................................................... 45° Right, 60° Left
Vise Jaw Depth ...................................................................................................... 43⁄8
"
"
Vise Jaw Height ..................................................................................................... 21⁄2
Max. Capacity Rectangular Height @ 90° .......................................................................... 5"
Max. Capacity Rectangular Width @ 90° ........................................................................... 6"
Max. Capacity Rectangular Height @ 60° ....................................................................... 13⁄4
"
Max. Capacity Rectangular Width @ 60° ....................................................................... 23⁄16"
Max. Capacity Rectangular Height @ 45° ......................................................................215⁄16"
Max. Capacity Rectangular Width @ 45° ........................................................................ 33⁄4
"
Max. Capacity Round @ 90° .......................................................................................... 5"
Max. Capacity Round @ 60......................................................................................... 13⁄4
Max. Capacity Round @ 45° ....................................................................................... 33⁄4
"
"
KXYc\ꢀ`e]f
Length................................................................................................................... 12"
Width.................................................................................................................. 41⁄2
"
Floor To Cutting Area Height ........................................................................................29"
DXZ_`e\ꢀJg\Z`]`ZXk`fej
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
Fm\iXccꢀ;`d\ej`fej
Weight .................................................................................................................. 150 lbs.
Length ......................................................................................................................... 39"
Width .......................................................................................................................233⁄8
Height ......................................................................................................................543⁄4
Foot Print (Length/Width).....................................................................................261⁄2" x 201⁄2
"
"
"
:fejkilZk`feꢀDXk\i`Xcj
Table.............................................................................................. Precision-Ground Cast Iron
Wheels..................................................................................................... Machined Cast Iron
Body.....................................................................................................................Cast Iron
Base..............................................................................Formed & Welded Steel w/Coolant Sump
Wheel Cover..................................................................................................... Formed Steel
Paint ........................................................................................................................Epoxy
J_`gg`e^ꢀ;`d\ej`fej
Weight ................................................................................................................... 176 lbs.
Length ......................................................................................................................... 41"
Width .......................................................................................................................... 19"
Height ......................................................................................................................... 22"
<c\Zki`ZXc
Switch ..................................................................................................... Automatic Shut-Off
Switch Voltage .............................................................................................................110V
Cord Length................................................................................................................. 6 ft.
Cord Gauge ............................................................................................................18 gauge
Recommended Breaker Size for 110V ................................................................................... 15A
Recommended Breaker Size for 220V ................................................................................... 15A
Included Plug Type .................................................................................................NEMA 5-15
Fk_\i
Wheel Size .................................................................................................................... 13"
Blade Guides.............................................................................................. Adjustable Carbide
ISO Factory ............................................................................................................ ISO 9001
Country of Origin .........................................................................................................China
Warranty ................................................................................................................. 2 Years
Serial Number Location.................................................................Machine ID Label on Body Frame
Assembly Time ......................................................................................................30 Minutes
=\Xkli\j
Control Panel Conveniently Located
Adjustable Hydraulic Downfeed
Quick Release Vise for Rapid Workpiece Change-Out
Blade Included
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
:fekifcjꢀXe[ꢀ=\Xkli\j
Blade Tension Knob
Blade Tension Gauge
Gearbox
Pulley Cover
Heavy-Duty Motor
Blade Guide Knob
Blade Guides
Hydraulic Cylinder
& Feed Rate Dial
Vise Clamp
Handwheel
ON/OFF Push-Button
Switch Assembly
Cast Iron Stop
Table Angle Scale
=`^li\ꢀ(% Model M1013.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
JkXe[Xi[ꢀ
J8=<KP
J8=<KP
DXZ_`e\ipꢀJX]\kp
I<8;ꢀD8EL8Cꢀ9<=FI<ꢀFG<I8K@E>ꢀD8:?@E<%
=8@CLI<ꢀKFꢀ=FCCFNꢀ@EJKIL:K@FEJꢀ9<CFNꢀN@CCꢀ
I<JLCKꢀ@EꢀG<IJFE8Cꢀ@EALIP%
@e[`ZXk\jꢀXeꢀ`dd`e\ekcpꢀ_XqXi[fljꢀj`klXk`feꢀn_`Z_#ꢀ`]ꢀefkꢀXmf`[\[#ꢀN@CCꢀ
i\jlckꢀ`eꢀ[\Xk_ꢀfiꢀj\i`fljꢀ`ealip%
@e[`ZXk\jꢀXꢀgfk\ek`Xccpꢀ_XqXi[fljꢀj`klXk`feꢀn_`Z_#ꢀ`]ꢀefkꢀXmf`[\[#ꢀ:FLC;ꢀ
i\jlckꢀ`eꢀ[\Xk_ꢀfiꢀj\i`fljꢀ`ealip%
@e[`ZXk\jꢀXꢀgfk\ek`Xccpꢀ_XqXi[fljꢀj`klXk`feꢀn_`Z_#ꢀ`]ꢀefkꢀXmf`[\[#ꢀD8Pꢀ
i\jlckꢀ`eꢀd`efiꢀfiꢀdf[\iXk\ꢀ`ealip%ꢀ
K_`jꢀjpdYfcꢀ`jꢀlj\[ꢀkfꢀXc\ikꢀk_\ꢀlj\iꢀkfꢀlj\]lcꢀ`e]fidXk`feꢀXYflkꢀgifg\iꢀ
fg\iXk`feꢀf]ꢀk_\ꢀ\hl`gd\ek#ꢀXe[&fiꢀXꢀj`klXk`feꢀk_XkꢀdXpꢀZXlj\ꢀ[XdX^\ꢀ
kfꢀk_\ꢀdXZ_`e\ip%
EFK@:<
JkXe[Xi[ꢀJX]\kpꢀ@ejkilZk`fej
(%ꢀꢀ I<8;ꢀK?IFL>?ꢀK?<ꢀ<EK@I<ꢀD8EL8Cꢀ9<=FI<ꢀJK8IK@E>ꢀD8:?@E<IP%ꢀDXZ_`e\ipꢀgi\j\ekjꢀj\i`fljꢀ
`ealipꢀ_XqXi[jꢀkfꢀlekiX`e\[ꢀlj\ij%ꢀ
)%ꢀ 8CN8PJꢀ LJ<ꢀ 8EJ@ꢀ 8GGIFM<;ꢀ J8=<KPꢀ >C8JJ<Jꢀ N?<Eꢀ FG<I8K@E>ꢀ D8:?@E<IP%ꢀ <m\ip[Xpꢀ \p\$
^cXjj\jꢀfecpꢀ_Xm\ꢀ`dgXZkꢀi\j`jkXekꢀc\ej\jÇk_\pꢀXi\ꢀEFKꢀjX]\kpꢀ^cXjj\j%
ꢀ
*%ꢀ 8CN8PJꢀN<8Iꢀ8ꢀE@FJ?ꢀ8GGIFM<;ꢀI<JG@I8KFIꢀN?<EꢀFG<I8K@E>ꢀD8:?@E<IPꢀK?8KꢀGIF;L:<Jꢀ
;LJK%ꢀNff[ꢀ[ljkꢀ`jꢀXꢀZXiZ`ef^\eꢀXe[ꢀZXeꢀZXlj\ꢀZXeZ\iꢀXe[ꢀj\m\i\ꢀi\jg`iXkfipꢀ`cce\jj\j%
+%ꢀ 8CN8PJꢀLJ<ꢀ?<8I@E>ꢀGIFK<:K@FEꢀN?<EꢀFG<I8K@E>ꢀD8:?@E<IP%ꢀDXZ_`e\ipꢀef`j\ꢀZXeꢀZXlj\ꢀ
g\idXe\ekꢀ_\Xi`e^ꢀ[XdX^\%ꢀ
,%ꢀ N<8IꢀGIFG<Iꢀ8GG8I<C%ꢀ;FꢀEFKꢀn\Xiꢀcffj\ꢀZcfk_`e^#ꢀ^cfm\j#ꢀe\Zbk`\j#ꢀi`e^j#ꢀfiꢀa\n\cipꢀn_`Z_ꢀdXpꢀ
^\kꢀZXl^_kꢀ`eꢀdfm`e^ꢀgXikj%ꢀN\Xiꢀgifk\Zk`m\ꢀ_X`iꢀZfm\i`e^ꢀkfꢀZfekX`eꢀcfe^ꢀ_X`iꢀXe[ꢀn\Xiꢀefe$jc`gꢀ
]ffkn\Xi%
-%ꢀ E<M<IꢀFG<I8K<ꢀD8:?@E<IPꢀN?<EꢀK@I<;#ꢀFIꢀLE;<IꢀK?<ꢀ@E=CL<E:<ꢀF=ꢀ;IL>JꢀFIꢀ8C:F?FC%ꢀ
9\ꢀd\ekXccpꢀXc\ikꢀXkꢀXccꢀk`d\jꢀn_\eꢀilee`e^ꢀdXZ_`e\ip%
.%ꢀ FECPꢀ8CCFNꢀKI8@E<;ꢀ8E;ꢀGIFG<ICPꢀJLG<IM@J<;ꢀG<IJFEE<CꢀKFꢀFG<I8K<ꢀD8:?@E<IP%ꢀDXb\ꢀ
jli\ꢀfg\iXk`feꢀ`ejkilZk`fejꢀXi\ꢀjX]\ꢀXe[ꢀZc\Xicpꢀle[\ijkff[%
/%ꢀ B<<Gꢀ:?@C;I<Eꢀ8E;ꢀM@J@KFIJꢀ8N8P%ꢀB\\gꢀXccꢀZ_`c[i\eꢀXe[ꢀm`j`kfijꢀXꢀjX]\ꢀ[`jkXeZ\ꢀ]ifdꢀk_\ꢀnfibꢀ
Xi\X%
0%ꢀꢀ D8B<ꢀNFIBJ?FGꢀ:?@C;ꢀGIFF=%ꢀLj\ꢀgX[cfZbj#ꢀdXjk\iꢀjn`kZ_\j#ꢀXe[ꢀi\dfm\ꢀjkXikꢀjn`kZ_ꢀb\pj%
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
('%ꢀE<M<IꢀC<8M<ꢀN?<EꢀD8:?@E<ꢀ@JꢀILEE@E>%ꢀKlieꢀgfn\iꢀF==ꢀXe[ꢀXccfnꢀXccꢀdfm`e^ꢀgXikjꢀkfꢀZfd\ꢀkfꢀ
XꢀZfdgc\k\ꢀjkfgꢀY\]fi\ꢀc\Xm`e^ꢀdXZ_`e\ꢀleXkk\e[\[%
((%ꢀ;FꢀEFKꢀLJ<ꢀ@Eꢀ;8E><IFLJꢀ<EM@IFED<EKJ%ꢀ;FꢀEFKꢀlj\ꢀdXZ_`e\ipꢀ`eꢀ[Xdg#ꢀn\kꢀcfZXk`fej#ꢀfiꢀ
n_\i\ꢀXepꢀ]cXddXYc\ꢀfiꢀefo`fljꢀ]ld\jꢀdXpꢀ\o`jk%ꢀ
()%ꢀB<<GꢀNFIBꢀ8I<8ꢀ:C<8Eꢀ8E;ꢀN<CCꢀC@K%ꢀ:clkk\iꢀXe[ꢀ[Xibꢀj_X[fnjꢀdXpꢀZXlj\ꢀXZZ`[\ekj%
(*%ꢀLJ<ꢀ8ꢀ>IFLE;<;ꢀ<OK<EJ@FEꢀ:FI;ꢀI8K<;ꢀ=FIꢀK?<ꢀD8:?@E<ꢀ8DG<I8><%ꢀLe[\ij`q\[ꢀZfi[jꢀfm\i$
_\XkꢀXe[ꢀcfj\ꢀgfn\i%ꢀI\gcXZ\ꢀ\ok\ej`feꢀZfi[jꢀ`]ꢀk_\pꢀY\Zfd\ꢀ[XdX^\[%ꢀ;FꢀEFKꢀlj\ꢀ\ok\ej`feꢀZfi[jꢀ
]fiꢀ))'MꢀdXZ_`e\ip%ꢀ
(+%ꢀ8CN8PJꢀ;@J:FEE<:Kꢀ=IFDꢀGFN<IꢀJFLI:<ꢀ9<=FI<ꢀJ<IM@:@E>ꢀD8:?@E<IP%ꢀDXb\ꢀjli\ꢀjn`kZ_ꢀ`jꢀ
`eꢀF==ꢀgfj`k`feꢀY\]fi\ꢀi\Zfee\Zk`e^%
(,%ꢀD8@EK8@EꢀD8:?@E<IPꢀN@K?ꢀ:8I<%ꢀB\\gꢀYcX[\jꢀj_XigꢀXe[ꢀZc\Xeꢀ]fiꢀY\jkꢀXe[ꢀjX]\jkꢀg\i]fidXeZ\%ꢀ
=fccfnꢀ`ejkilZk`fejꢀ]fiꢀclYi`ZXk`e^ꢀXe[ꢀZ_Xe^`e^ꢀXZZ\jjfi`\j%
(-%ꢀD8B<ꢀJLI<ꢀ>L8I;Jꢀ8I<ꢀ@EꢀGC8:<ꢀ8E;ꢀNFIBꢀ:FII<:KCPꢀ9<=FI<ꢀLJ@E>ꢀD8:?@E<IP%
(.%ꢀI<DFM<ꢀ 8;ALJK@E>ꢀ B<PJꢀ 8E;ꢀ NI<E:?<J%ꢀ DXb\ꢀ Xꢀ _XY`kꢀ f]ꢀ Z_\Zb`e^ꢀ ]fiꢀ b\pjꢀ Xe[ꢀ X[aljk`e^ꢀ
ni\eZ_\jꢀY\]fi\ꢀklie`e^ꢀdXZ_`e\ipꢀFE%
(/%ꢀ:?<:Bꢀ =FIꢀ ;8D8><;ꢀ G8IKJꢀ 9<=FI<ꢀ LJ@E>ꢀ D8:?@E<IP%ꢀ :_\Zbꢀ ]fiꢀ Y`e[`e^ꢀ Xe[ꢀ Xc`^ed\ekꢀ f]ꢀ
gXikj#ꢀYifb\eꢀgXikj#ꢀgXikꢀdflek`e^#ꢀcffj\ꢀYfckj#ꢀXe[ꢀXepꢀfk_\iꢀZfe[`k`fejꢀk_XkꢀdXpꢀX]]\ZkꢀdXZ_`e\ꢀ
fg\iXk`fe%ꢀI\gX`iꢀfiꢀi\gcXZ\ꢀ[XdX^\[ꢀgXikj%
(0%ꢀLJ<ꢀI<:FDD<E;<;ꢀ8::<JJFI@<J%ꢀI\]\iꢀkfꢀk_\ꢀ`ejkilZk`feꢀdXelXcꢀ]fiꢀi\Zfdd\e[\[ꢀXZZ\jjfi`\j%ꢀ
K_\ꢀlj\ꢀf]ꢀ`dgifg\iꢀXZZ\jjfi`\jꢀdXpꢀZXlj\ꢀi`jbꢀf]ꢀ`ealip%
)'%ꢀ;FꢀEFKꢀ=FI:<ꢀD8:?@E<IP%ꢀNfibꢀXkꢀk_\ꢀjg\\[ꢀ]fiꢀn_`Z_ꢀk_\ꢀdXZ_`e\ꢀfiꢀXZZ\jjfipꢀnXjꢀ[\j`^e\[%
)(%ꢀJ<:LI<ꢀ NFIBG@<:<%ꢀ Lj\ꢀ ZcXdgjꢀ fiꢀ Xꢀ m`j\ꢀ kfꢀ _fc[ꢀ k_\ꢀ nfibg`\Z\ꢀ n_\eꢀ giXZk`ZXc%ꢀ 8ꢀ j\Zli\[ꢀ
nfibg`\Z\ꢀgifk\Zkjꢀpfliꢀ_Xe[jꢀXe[ꢀ]i\\jꢀYfk_ꢀ_Xe[jꢀkfꢀfg\iXk\ꢀk_\ꢀdXZ_`e\%
))%ꢀ;FꢀEFKꢀFM<II<8:?%ꢀB\\gꢀgifg\iꢀ]ffk`e^ꢀXe[ꢀYXcXeZ\ꢀXkꢀXccꢀk`d\j%
)*%ꢀD8EPꢀD8:?@E<JꢀN@CCꢀ<A<:KꢀK?<ꢀNFIBG@<:<ꢀKFN8I;ꢀK?<ꢀFG<I8KFI%ꢀBefnꢀXe[ꢀXmf`[ꢀZfe[`$
k`fejꢀk_XkꢀZXlj\ꢀk_\ꢀnfibg`\Z\ꢀkfꢀꢁb`ZbYXZb%ꢁ
)+%ꢀ8CN8PJꢀCF:BꢀDF9@C<ꢀ98J<Jꢀꢂ@=ꢀLJ<; ꢀ9<=FI<ꢀFG<I8K@E>ꢀD8:?@E<IP%
),%ꢀ9<ꢀ8N8I<ꢀK?8Kꢀ:<IK8@Eꢀ;LJKꢀD8Pꢀ9<ꢀ?8Q8I;FLJꢀkfꢀk_\ꢀi\jg`iXkfipꢀjpjk\djꢀf]ꢀg\fgc\ꢀXe[ꢀ
Xe`dXcj#ꢀ\jg\Z`Xccpꢀ]`e\ꢀ[ljk%ꢀDXb\ꢀjli\ꢀpflꢀbefnꢀk_\ꢀ_XqXi[jꢀXjjfZ`Xk\[ꢀn`k_ꢀk_\ꢀkpg\ꢀf]ꢀ[ljkꢀpflꢀ
n`ccꢀY\ꢀ\ogfj\[ꢀkfꢀXe[ꢀXcnXpjꢀn\XiꢀXꢀi\jg`iXkfiꢀXggifm\[ꢀ]fiꢀk_Xkꢀkpg\ꢀf]ꢀ[ljk%ꢀ
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
8[[`k`feXcꢀJX]\kpꢀ]fiꢀD\kXcꢀ:lkk`e^ꢀ9Xe[jXnj
I<8;ꢀXe[ꢀle[\ijkXe[ꢀk_`jꢀ
LJ<ꢀk_`jꢀXe[ꢀfk_\iꢀdXZ_`e\ipꢀn`k_ꢀZXlk`feꢀ
\ek`i\ꢀdXelXcꢀY\]fi\ꢀlj`e^ꢀ
Xe[ꢀi\jg\Zk%ꢀ8cnXpjꢀZfej`[\iꢀjX]\kpꢀ]`ijk#ꢀ
k_`jꢀdXZ_`e\%ꢀJ\i`fljꢀg\i$
Xjꢀ `kꢀ Xggc`\jꢀ kfꢀ pfliꢀ `e[`m`[lXcꢀ nfib`e^ꢀ
jfeXcꢀ `ealipꢀ dXpꢀ fZZliꢀ
Zfe[`k`fej%ꢀEfꢀc`jkꢀf]ꢀjX]\kpꢀ^l`[\c`e\jꢀZXeꢀ
`]ꢀ jX]\kpꢀ Xe[ꢀ fg\iXk`feXcꢀ
Y\ꢀ Zfdgc\k\Ç\m\ipꢀ j_fgꢀ \em`ifed\ekꢀ `jꢀ
`e]fidXk`feꢀ `jꢀ efkꢀ le[\i$
[`]]\i\ek%ꢀ=X`cli\ꢀkfꢀ]fccfnꢀ^l`[\c`e\jꢀZflc[ꢀ
jkff[ꢀ Xe[ꢀ ]fccfn\[%ꢀ ;Fꢀ
i\jlckꢀ `eꢀ j\i`fljꢀ g\ijfeXcꢀ `ealip#ꢀ [XdX^\ꢀ
EFKꢀ i`jbꢀ pfliꢀ jX]\kpꢀ Ypꢀ
kfꢀ\hl`gd\ekꢀfiꢀgffiꢀnfibꢀi\jlckj%
efkꢀi\X[`e^ꢁ
(%ꢀ 9cX[\ꢀ:fe[`k`fe1 Do not operate with a dull, cracked or badly worn blade—they can break during
use or greatly decrease cutting performance. Inspect blades for cracks and missing teeth before
each use.
)%ꢀ 9cX[\ꢀI\gcXZ\d\ek1 Wear gloves to protect hands and safety glasses to protect eyes when
replacing the blade. When replacing blades, make sure teeth face forward and down toward the
table in the direction of blade travel.
*%ꢀ Nfibg`\Z\ꢀ?Xe[c`e^1 Your hands can be cut or drawn into the blade during operation if the
workpiece moves unexpectedly. Always keep your hands a safe distance away from the moving
blade.
+%ꢀ DX^e\j`ldꢀ=`i\ꢀ?XqXi[1 Use EXTREME CAUTION if cutting magnesium. Using the wrong cutting
fluid or overheating material could lead to an extremely hot fire that is difficult to extinguish.
Additionally, do not allow magnesium swarf or dust to pile up around the machine and only dispose
of the waste using approved methods.
,%ꢀ ?fkꢀJli]XZ\j1 Be aware that touching hot workpieces or chips after welding, grinding, or cutting
can cause burns.
-%ꢀ :lkk`e^ꢀ=cl`[ꢀJX]\kp1 If cutting fluid is used for operations, only use the minimum amount
necessary, and promptly clean it from the machine and work area after use. Cutting fluid is
associated with skin disease, lung damage, and cancer. Avoid breathing, ingesting, or touching
cutting fluid and always wear approved personal protective equipment when using or cleaning it.
Always follow the manufacturer's recommendation to ensure safe and appropriate use.
.%ꢀ <ekXe^c\d\ekꢀ?XqXi[j1 Always keep the blade guard correctly positioned and wheel doors closed
and secured when bandsaw is in operation. Loose clothing, jewelry, long hair and work gloves can
be drawn into working parts.
/%ꢀ LejkXYc\ꢀNfibg`\Z\j1 Workpieces that cannot be supported or stabilized without a vise or jig
should not be cut on a vertical metal-cutting bandsaw, because they can unexpectedly move while
cutting and draw the operator's hands into the blade causing serious personal injury. Examples are
chains, cables, round or oblong-shaped workpieces, workpieces with internal or built-in moving or
rotations parts, etc.
0%ꢀꢀ :c\Xi`e^ꢀ:_`gj1 Metal chips can easily cut skin—even through a piece of cloth. Avoid clearing chips
by hand or with a rag. Use a brush or vacuum to clear metal chips.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
<C<:KI@:8C
K_\ꢀ dXZ_`e\ꢀ dljkꢀ Y\ꢀ gifg\icpꢀ j\kꢀ lgꢀ Y\]fi\ꢀ `kꢀ `jꢀ
jX]\ꢀkfꢀfg\iXk\%ꢀ;FꢀEFKꢀZfee\Zkꢀk_`jꢀdXZ_`e\ꢀkfꢀk_\ꢀ
gfn\iꢀjfliZ\ꢀlek`cꢀ`ejkilZk\[ꢀkfꢀ[fꢀjfꢀ`eꢀk_\ꢀꢃK\jkꢀ
Ileꢃꢀgfik`feꢀf]ꢀk_`jꢀdXelXc%
(('M&))'MꢀFg\iXk`fe
The ModelꢀM1013 is prewired for 110V operation. For 220V
operation, the motor must be re-wired as directed by
the wiring diagram on the inside of the motor junction
box cover. If this diagram is not available, use the wiring
diagram on GX^\ꢀ*(.
The power supply circuit used for this machine MUST be
grounded and rated for the amperage given below. Never
replace a circuit breaker with one of higher amperage
without consulting a qualified electrician to ensure
compliance with wiring codes.
-$(,G
-$(,I
=`^li\ꢀ)% NEMA 5-15 and 6-15 plugs and
receptacles.
This machine must be grounded! The cord supplied with
this machine comes with a grounding wire. If your outlet
does not accommodate a ground pin, have it replaced by
a qualified electrician.
@]ꢀpflꢀXi\ꢀlejli\ꢀXYflkꢀk_\ꢀn`i`e^ꢀZf[\jꢀ`eꢀpfliꢀXi\Xꢀ
fiꢀpflꢀgcXeꢀkfꢀZfee\ZkꢀpfliꢀdXZ_`e\ꢀkfꢀXꢀj_Xi\[ꢀZ`i$
Zl`k#ꢀpflꢀdXpꢀZi\Xk\ꢀXꢀ]`i\ꢀfiꢀZ`iZl`kꢀfm\icfX[ꢀ_XqXi[Ç
ZfejlckꢀXꢀhlXc`]`\[ꢀ\c\Zki`Z`Xeꢀkfꢀi\[lZ\ꢀk_`jꢀi`jb%
;FꢀEFKꢀnfibꢀfeꢀpfliꢀ\c\Zki`ZXcꢀjpjk\dꢀ
`]ꢀ pflꢀ Xi\ꢀ lejli\ꢀ XYflkꢀ \c\Zki`ZXcꢀ
Zf[\jꢀXe[ꢀn`i`e^ꢁꢀJ\\bꢀXjj`jkXeZ\ꢀ]ifdꢀ
Xꢀ hlXc`]`\[ꢀ \c\Zki`Z`Xe%ꢀ @^efi`e^ꢀ k_`jꢀ
nXie`e^ꢀZXeꢀZXlj\ꢀ\c\ZkifZlk`fe#ꢀ]`i\#ꢀ
fiꢀdXZ_`e\ꢀ[XdX^\%
<ok\ej`feꢀ:fi[j
We do not recommend using an extension cord; however,
if you have no alternative, use the following guidelines:
•
•
•
•
Use a cord rated for Standard Service (S).
Do not use an extension cord longer than 50 feet.
Ensure that the cord has a ground wire and pin.
Use the gauge size listed below as a minimum.
<c\Zki`ZXcꢀJg\Z`]`ZXk`fej
Fg\iXk`e^ꢀMfckX^\
110V Operation
220V Operation
8dgꢀ;iXn
7 Amps
D`e%ꢀ:`iZl`kꢀJ`q\
I\Zfdd\e[\[ꢀGcl^
NEMA 5-15 (incl.)
<ok\ej`feꢀ:fi[
14 Gauge
15A
15A
-9-
3.5 Amps
NEMA 6-15 (not incl.)
16 Gauge
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
J<KLG
A% Belt Cover .................................1
B% Work Stop..................................1
C% Work Stop Shaft...........................1
D% Wheels .....................................2
LegXZb`e^
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
8jj\dYcpꢀ?Xi[nXi\ꢀꢂEfkꢀJ_fne 1
—Hex Wrench 4mm ............................1
—Hex Bolt M8-1.25 x 30.......................4
—Flat Washer 17mm (Wheels) ...............4
—Flat Washer 8mm ............................4
—Cotter Pin 1⁄8" x 1" (Wheels) ...............2
—Hex Nut M8-1.25 (Feet).....................2
—Phillips Head Screw M6-1 x 12........... 16
—Flat Washer 6mm .......................... 16
—Hex Bolt 1⁄4"-20 x 1⁄2" .......................2
—Flat Washer 1⁄4" ..............................2
@em\ekfip
The following is a description of the main components
shipped with the Model M1013. Lay the components out to
inventory them.
Efk\1 @]ꢀpflꢀZXeꢁkꢀ]`e[ꢀXeꢀ`k\dꢀfeꢀk_`jꢀc`jk#ꢀZ_\Zbꢀk_\ꢀ
dflek`e^ꢀcfZXk`feꢀfeꢀk_\ꢀdXZ_`e\ꢀfiꢀ\oXd`e\ꢀk_\ꢀ
gXZbX^`e^ꢀdXk\i`XcjꢀZXi\]lccp%ꢀFZZXj`feXccpꢀn\ꢀgi\$`ejkXccꢀ
Z\ikX`eꢀZfdgfe\ekjꢀ]fiꢀjX]\iꢀj_`gg`e^%
@em\ekfipꢀꢂ=`^li\ꢀ* ꢀ
Hkp
8% Base..........................................................1
9% Front Panel .................................................1
:% Rear Panel ..................................................1
;% Right Panel .................................................1
<% Left Panel...................................................1
=% Chip Tray....................................................1
>% Feet..........................................................4
?% Axle..........................................................1
@% V-Belt........................................................1
B\\gꢀ dXZ_`e\ꢀ [`jZfee\Zk\[ꢀ ]ifdꢀ
gfn\iꢀlek`cꢀ`ejkilZk\[ꢀfk_\in`j\%
:
9
8
>
=
?
;
@
<
D
A
B
C
=`^li\ꢀ*% Model M1013 inventory.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
DXZ_`e\ꢀGcXZ\d\ek
:c\Xe`e^ꢀDXZ_`e\
The table and other unpainted parts of your
metal cutting bandsaw are coated with a waxy
grease that protects them from corrosion during
shipment. Clean this grease off with a solvent
cleaner or citrus-based degreaser. DO NOT use
chlorine-based solvents such as brake parts
cleaner or acetone—if you happen to splash
some onto a painted surface, you will ruin the
finish.
›ꢀ =cffiꢀCfX[1 This machine distributes a
heavy load in a small footprint. Some
residential floors may require additional
bracing to support both machine and
operator.
›ꢀ Nfib`e^ꢀ:c\XiXeZ\j1 Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your Machine Type.
E<M<IꢀZc\Xeꢀn`k_ꢀ^Xjfc`e\ꢀ
fiꢀ fk_\iꢀ g\kifc\ld$
YXj\[ꢀjfcm\ekj%ꢀDfjkꢀ_Xm\ꢀ
cfnꢀ ]cXj_ꢀ gf`ekj#ꢀ n_`Z_ꢀ
dXb\ꢀ k_\dꢀ \oki\d\cpꢀ
]cXddXYc\%ꢀ 8ꢀ i`jbꢀ f]ꢀ
\ogcfj`feꢀ Xe[ꢀ Ylie`e^ꢀ
\o`jkjꢀ `]ꢀ k_\j\ꢀ gif[lZkjꢀ
Xi\ꢀlj\[%ꢀJ\i`fljꢀg\ijfeXcꢀ
`ealipꢀ dXpꢀ fZZliꢀ `]ꢀ k_`jꢀ
nXie`e^ꢀ`jꢀ`^efi\[ꢁ
›ꢀ C`^_k`e^1 Lighting should be bright enough
to eliminate shadow and prevent eye strain.
›ꢀ <c\Zki`ZXc1ꢀElectrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so power or
extension cords are clear of high-traffic
areas. Follow local electrical codes for
proper installation of new lighting, outlets,
or circuits.
LJ<ꢀ _\cg\ijꢀ fiꢀ gfn\iꢀ
c`]k`e^ꢀ \hl`gd\ekꢀ kfꢀ
c`]kꢀ k_`jꢀ DXZ_`e\ꢀ EXd\%ꢀ
Fk_\in`j\#ꢀ j\i`fljꢀ g\i$
jfeXcꢀ`ealipꢀdXpꢀfZZli%ꢀ
8CN8PJꢀ nfibꢀ `eꢀ n\cc$
m\ek`cXk\[ꢀXi\Xjꢀ]Xiꢀ]ifdꢀ
gfjj`Yc\ꢀ `^e`k`feꢀ jfliZ\jꢀ
n_\eꢀ lj`e^ꢀ jfcm\ekjꢀ kfꢀ
Zc\Xeꢀ dXZ_`e\ip%ꢀ DXepꢀ
jfcm\ekjꢀ Xi\ꢀ kfo`Zꢀ n_\eꢀ
`e_Xc\[ꢀfiꢀ`e^\jk\[%ꢀLj\ꢀ
ZXi\ꢀ n_\eꢀ [`jgfj`e^ꢀ
f]ꢀ nXjk\ꢀ iX^jꢀ Xe[ꢀ
kfn\cjꢀ kfꢀ Y\ꢀ jli\ꢀ k_\pꢀ
;Fꢀ EFKꢀ Zi\Xk\ꢀ ]`i\ꢀ fiꢀ
\em`ifed\ekXcꢀ_XqXi[j%ꢀ
D8B<ꢀ pfliꢀ j_fgꢀ ÈZ_`c[ꢀ
jX]\%Éꢀ <ejli\ꢀ k_Xkꢀ pfliꢀ
nfibgcXZ\ꢀ `jꢀ `eXZZ\jj`Yc\ꢀ
kfꢀ Z_`c[i\eꢀ Ypꢀ Zcfj`e^ꢀ Xe[ꢀ
cfZb`e^ꢀXccꢀ\ekiXeZ\jꢀn_\eꢀ
pflꢀXi\ꢀXnXp%ꢀE<M<IꢀXccfnꢀ
lekiX`e\[ꢀ m`j`kfijꢀ `eꢀ pfliꢀ
j_fgꢀ n_\eꢀ Xjj\dYc`e^#ꢀ
X[aljk`e^ꢀ fiꢀ fg\iXk`e^ꢀ
\hl`gd\ek%ꢀ
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
N_\\cj#ꢀ=\\k#ꢀXe[ꢀ
:XY`e\k
This bandsaw is shipped with four rubber feet with posts
and two wheels with an axle. It is your option to install
four rubber feet if you do not need to move the bandsaw,
or install the axle and wheels if you need to move the
bandsaw regularly.
Kfꢀ`ejkXccꢀk_\ꢀn_\\cj#ꢀ]\\k#ꢀXe[ꢀk_\ꢀZXY`e\k#ꢀ[fꢀk_\j\ꢀ
jk\gj1
(% At the end of the base with the axle holes, insert
the axle into the base (see =`^li\ꢀ+).
)% Slide a 17mm flat washer and wheel onto each end
of the axle, followed by another 17mm flat washer
and cotter pin.
=`^li\ꢀ+% Installing wheels and feet.
=`^li\ꢀ,% Front and rear panels installed.
=`^li\ꢀ-% Left panel installed.
*% Thread a 3⁄8-16 hex nut on both rubber feet.
+% Thread rubber feet into the base (see =`^li\ꢀ+).
,% Position the base on the floor, and adjust the feet
until the base is level and stable.
-% Tighten the hex nuts against the base to lock the
feet in position.
.% Position the front and rear panels on the base and
install the panels to the base with four M6-1 x 12
Phillips head screws and 6mm flat washers, as shown
in =`^li\ꢀ,.
/% Position the left panel between the front and rear
panels, and secure it in place with six M6-1 x 12
Phillips head screws and 6mm flat washers, as shown
in =`^li\ꢀ-.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
0% Position the right panel between the front and rear
panel, and secure it in place with six M6-1 x 12
Phillips head screws and 6mm flat washers, as shown
in =`^li\ꢀ..
K_\ꢀDf[\cꢀD('(*ꢀ`jꢀ_\XmpꢁꢀKfꢀ
Xmf`[ꢀg\ijfeXcꢀ`ealip#ꢀ^\kꢀ_\cgꢀkfꢀ
c`]kꢀk_`jꢀdXZ_`e\%
('% With the help of an assistant or a hoisting device,
place the bandsaw onto the cabinet.
=`^li\ꢀ.% Installing right panel.
((% Secure the bandsaw to the cabinet with four M8-1.25
x 30 hex bolts and 8mm flat washers, as shown in
=`^li\ꢀ/.
=`^li\ꢀ/% Installing bandsaw to cabinet.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
J_`gg`e^ꢀJkiXgꢀI\dfmXcꢀꢄꢀ
Jkfgꢀ8[aljkd\ek
To ensure that your bandsaw arrives without damage to
the hinge system, a shipping strap was installed. After
removing the shipping strap, you will have to make a
series of adjustments, beginning with the feed stop bolt.
Shipping Brace
Kfꢀi\dfm\ꢀk_\ꢀj_`gg`e^ꢀjkiXgꢀXe[ꢀX[aljkꢀk_\ꢀ]\\[ꢀjkfgꢀ
Yfck#ꢀ[fꢀk_\j\ꢀjk\gj1
(% Remove the shipping strap hex bolt and strap with a
12mm wrench, as shown in =`^li\ꢀ0.
Efk\1 B\\gꢀk_`jꢀj_`gg`e^ꢀjkiXgꢀ`eꢀk_\ꢀ\m\ekꢀk_Xkꢀpflꢀ
dljkꢀkiXejgfikꢀfiꢀj_`gꢀk_\ꢀYXe[jXn%
)% Adjust the feed stop bolt and jam nut with a 14mm
wrench (=`^li\ꢀ('), so the bandsaw blade teeth
are just below the table surface when the cut is
complete.
=`^li\ꢀ0% Removing shipping strap.
JhlXi`e^ꢀM`j\ꢀkfꢀ9cX[\
To ensure that your bandsaw will make cuts that match
the degree scale, you must make sure to square the vise
to the blade.
KfꢀjhlXi\ꢀk_\ꢀm`j\ꢀkfꢀk_\ꢀYcX[\#ꢀ[fꢀk_\j\ꢀjk\gj1
Feed Stop
Bolt
(% Rotate the headstock until the pointer reads "0" on
the tabletop scale, and tighten the headstock lock
lever so the headstock stays indexed at zero.
=`^li\ꢀ('% Feed stop bolt.
)% Using a 6mm wrench, loosen the two cap screws that
hold the vise to the table, as shown in =`^li\ꢀ((.
Headstock
Lock
*% Using a small machinists square, adjust the vise so it
Lever
is square to the blade.
+% Tighten the two cap screws, so the vise and blade
are square with one another.
=`^li\ꢀ((% Squaring vise to blade,
headstock, and table scale.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
:_`gꢀKiXpꢀꢄꢀ:Xjkꢀ@ifeꢀ
Jkfg
The chip tray directs small workpieces into a bucket when
the cut is complete. The cast iron stop allows you to
repeat cuts at the same length.
Kfꢀ`ejkXccꢀk_\ꢀZ_`gꢀkiXpꢀXe[ꢀZXjkꢀ`ifeꢀjkfg#ꢀ[fꢀk_\j\ꢀ
jk\gj1
(% Position the chip tray, as shown in =`^li\ꢀ().
)% Insert the stop rod approximately 3⁄4" into the saw
until the end of the rod is just flush with the inside
casting surface, as shown in =`^li\ꢀ(*.
Chip Tray
=`^li\ꢀ()% Chip tray installed.
*% Use a 4mm hex wrench to tighten the set screw
shown in =`^li\ꢀ(*.
+% Slide the cast iron stop onto the stop rod and tighten
the set screw in the side of the stop, as shown in
=`^li\ꢀ(+.
Set Screw
=`^li\ꢀ(*% Installing stop rod.
Set Screw
=`^li\ꢀ(+% Cast iron stop installed.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
8lkfdXk`ZꢀF==ꢀ
8[aljkd\ek
After you have removed the shipping strap and have
adjusted the headstock stop bolt, you must adjust the
OFF button lever stop bolt, so the bandsaw shuts OFF
automatically when a cut is complete.
Stop Bolt
& Jam Nut
Kfꢀj\kꢀk_\ꢀX[aljkꢀk_\ꢀF==ꢀYlkkfe#ꢀ[fꢀk_\j\ꢀjk\gj1
(% With the headstock in the complete down position,
loosen the 12mm stop bolt and jam nut shown in
=`^li\ꢀ(,.
)% Push down on the OFF button lever so the button is
OFF Button
Lever
completely depressed.
*% While keeping the lever depressed, use your
fingertips to turn the stop bolt until the head just
touches the lever.
=`^li\ꢀ(,% Automatic OFF components.
4. Back off the stop bolt 1⁄3 turn and tighten the jam
nut.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
Glcc\pꢀ:fm\i
When opened, the pulley cover gives you access to change
the pulley ratio so the bandsaw can cut at one of three
speeds.
<EK8E>C<D<EKꢀ?8Q8I;ꢁ
D8B<ꢀ JLI<ꢀ k_\ꢀ YXe[jXnꢀ `jꢀ
legcl^^\[ꢀ Y\]fi\ꢀ gifZ\\[`e^ꢁꢀ
Fk_\in`j\#ꢀ j\m\i\ꢀ `ealipꢀ dXpꢀ
fZZli%
Kfꢀ`ejkXccꢀk_\ꢀglcc\pꢀZfm\i#ꢀ[fꢀk_\j\ꢀjk\gj1
=`^li\ꢀ(-% Positioning the pulley cover.
(% Position and rotate the pulley cover into place, as
shown in =`^li\ꢀ(-.
)% Install the two 1⁄4-20 x 1⁄2" hex bolts and washers to
secure the pulley cover.
*% Loosen the belt tension knob enough to install the
belt on the appropriate pulley that will give the
required blade speed. Refer to 9cX[\ꢀJg\\[ on GX^\ꢀ
)* for blade speed selections.
Belt Tension
Knob
+% Adjust the belt tension knob (=`^li\ꢀ(.), so the
belt has approximately 1⁄4" deflection when pressed
in between the pulleys, then close and secure the
cover.
=`^li\ꢀ(.% Belt tension knob.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
9cX[\ꢀK\ej`fe
Proper blade tension is essential to long blade life,
straight cuts, and efficient cutting.
Cylinder
Lock Pin
Two major signs that you do not have proper blade
tension are: 1) the blade stalls in the cut and slips on the
wheels, and 2) the blade frequently breaks from being too
tight.
Safety
Stop
;`jZfee\Zkꢀ YXe[jXnꢀ ]ifdꢀ gfn\iꢀ
9<=FI<ꢀ dXb`e^ꢀ Xe[ꢀ X[aljkd\ekjꢀ
kfꢀk_\ꢀdXZ_`e\ꢁ
=`^li\ꢀ(/%ꢀRaising and locking headstock.
Kfꢀj\kꢀk_\ꢀYcX[\ꢀk\ej`fe#ꢀ[fꢀk_\j\ꢀjk\gj1
Blade
Tension
Knob
(% Make sure the blade is tracking properly (refer
to 9cX[\ꢀKiXZb`e^ on GX^\ꢀ)0 for detailed
instructions).
)% Remove the cylinder lock pin, raise the headstock to
the full vertical position, and push the safety stop
inward to lock the headstock in the vertical position
(see =`^li\ꢀ(/ .
*% Open the blade cover, as shown in =`^li\ꢀ(0#ꢀslide
the blade guides as far apart as possible, then
secure them in place
+% Turn the blade tension knob until the blade is snug,
and the blade tension scale indicates "medium" (see
=`^li\ꢀ)').
=`^li\ꢀ(0%ꢀBlade tension adjustment knob.
Blade Tension Scale
,% Adjust the blade guides as instructed in the next
subsection
-% Close and secure the blade guard.
=`^li\ꢀ)'% Typical blade tension scale.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
9cX[\ꢀ>l`[\j
The blade guide side bearings support and twist the
blade straight so the blade will enter the workpiece
perpendicular to the table surface (see Figure )(). The
blade guide support bearings prevent blade twist by
stopping the blade from being pushed back during a cut.
Both adjustments are critical for correct saw operation.
Blade Guide Support Bearing
Guide
Bearing
Adjustment
Hex Bolt
Side Bearing
Eccentric
and Jam Nut
Note: Make sure the blade is tensioned and tracks
correctly before you adjust the blade guide bearings.
Refer to Blade Tension on the previous page and Blade
Tracking on Pageꢀ)0 for detailed instructions.
Blade Guide Side Bearing
To adjust the guide bearings, do these steps:
=`^li\ꢀ)(% Blade guide adjustment
locations.
(% DISCONNECT BANDSAW FROM POWER!
)% Let the bandsaw headstock park in the full down
Side Bearing Eccentric
and Jam Nut
position.
*% Use a 12mm wrench to loosen the lower guide
bearing adjustment hex bolt shown in =`^li\ꢀ)).
+% Adjust the blade guide housing so the support
bearing rests against the rear of the blade, as
illustrated in =`^li\ꢀ)(%ꢀ
Guide Bearing
Adjustment
Hex Bolt
,% Tighten the adjustment hex bolt.
-% Use a 14mm wrench to loosen the outer side bearing
eccentric jam nuts of the upper guide bearing.
=`^li\ꢀ))% Blade guide adjustments.
Note: The inner side bearing are not on eccentric
shafts and cannot be adjusted.
.% Use a 12mm wrench to rotate the side bearing
eccentrics until the bearings hold the blade
perpendicular to the table surface, and have a
bearing-to-blade clearance of 0.000"—0.001". The
bearings must not pinch the blade.ꢀ
Lock Knob
ꢀ
Note: To make sure the blade is perpendicular to the
table, use a standard machinist's square.
/% Tighten the jam nuts, loosen the lock knob, and slide
the blade guide close to the workpiece so the blade
is supported and will not twist during the cut (see
=`^li\ꢀ)*).
=`^li\ꢀ)*% Blade guide position lock knob.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
K\jkꢀIle
Once the assembly is complete, test run your machine to
make sure it runs properly.
If, during the test run, you cannot easily locate the
source of an unusual noise or vibration, stop using the
machine immediately, then review the KiflYc\j_ffk`e^
on GX^\ꢀ*).
Gifa\Zk`c\jꢀ k_ifneꢀ ]ifdꢀ k_\ꢀ dXZ_`e\ꢀ
Zflc[ꢀZXlj\ꢀj\i`fljꢀ\p\ꢀ`ealip%ꢀN\Xiꢀ
jX]\kpꢀ ^cXjj\jꢀ kfꢀ i\[lZ\ꢀ k_\ꢀ i`jbꢀ f]ꢀ
`ealip%
If you still cannot remedy a problem, contact our Tech
Support at (360) 734-3482 for assistance.
Kfꢀk\jkꢀileꢀk_\ꢀdXZ_`e\#ꢀ[fꢀk_\j\ꢀjk\gj1
(% Make sure you understand the safety instructions
at the beginning of the manual, and verify that the
machine is setup properly.
)% Ensure all tools and objects used during set up are
cleared away from the machine.
*% Connect the machine to the power source.
+% Start the bandsaw while keeping your finger near
the ON/OFF switch at all times during the test run.
The bandsaw should run smoothly with little or no
vibration.
Cffj\ꢀ _X`iꢀ Xe[ꢀ Zcfk_`e^ꢀ Zflc[ꢀ ^\kꢀ
ZXl^_kꢀ`eꢀdXZ_`e\ipꢀXe[ꢀZXlj\ꢀj\i`fljꢀ
g\ijfeXcꢀ `ealip%ꢀ B\\gꢀ cffj\ꢀ Zcfk_`e^ꢀ
ifcc\[ꢀ lgꢀ Xe[ꢀ cfe^ꢀ _X`iꢀ k`\[ꢀ lgꢀ Xe[ꢀ
XnXpꢀ]ifdꢀdXZ_`e\ip%
— Strange or unusual noises should be investigated
and corrected before operating the machine
further. Always disconnect the machine from
power when investigating or correcting potential
problems.
,% Turn the machine F==.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
FG<I8K@FEJ
>\e\iXc
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. @]ꢀXkꢀXepꢀ
k`d\ꢀpflꢀXi\ꢀ\og\i`\eZ`e^ꢀ[`]]`Zlck`\jꢀg\i]fid`e^ꢀXepꢀ
fg\iXk`fe#ꢀjkfgꢀlj`e^ꢀk_\ꢀdXZ_`e\ꢁ
I<8;ꢀXe[ꢀle[\ijkXe[ꢀk_`jꢀ\ek`i\ꢀ`ejkilZ$
k`feꢀdXelXcꢀY\]fi\ꢀlj`e^ꢀk_`jꢀdXZ_`e\%ꢀ
J\i`fljꢀ g\ijfeXcꢀ `ealipꢀ dXpꢀ fZZliꢀ `]ꢀ
jX]\kpꢀXe[ꢀfg\iXk`feXcꢀ`e]fidXk`feꢀ`jꢀefkꢀ
le[\ijkff[ꢀ Xe[ꢀ ]fccfn\[%ꢀ ;Fꢀ EFKꢀ i`jbꢀ
pfliꢀjX]\kpꢀYpꢀefkꢀi\X[`e^ꢁ
If you are an inexperienced operator, we strongly
recommend that you read books or trade articles, or
seek training from an experienced DXZ_`e\ꢀKpg\ operator
before performing any unfamiliar operations. 8Yfm\ꢀXcc#ꢀ
pfliꢀjX]\kpꢀj_flc[ꢀZfd\ꢀ]`ijkꢁ
Fg\iXk`fe
Before making cuts to the workpiece, it is important
that all safety precautions and bandsaw adjustments are
addressed.
=fiꢀYXj`ZꢀZlkk`e^ꢀfg\iXk`fej#ꢀ[fꢀk_\j\ꢀjk\gj1
(% Select and install the required blade (refer to
9cX[\ꢀJ\c\Zk`fe on GX^\ꢀ)+).
;FꢀEFKꢀ`em\jk`^Xk\ꢀgifYc\djꢀfiꢀX[aljkꢀ
k_\ꢀdXZ_`e\ꢀn_`c\ꢀ`kꢀ`jꢀilee`e^%ꢀNX`kꢀ
lek`cꢀ k_\ꢀ dXZ_`e\ꢀ `jꢀ klie\[ꢀ F==#ꢀ
legcl^^\[ꢀ Xe[ꢀ Xccꢀ nfib`e^ꢀ gXikjꢀ
_Xm\ꢀZfd\ꢀkfꢀXꢀZfdgc\k\ꢀjkfgꢀY\]fi\ꢀ
gifZ\\[`e^ꢁ
)% Select the required cutting speed (refer to 9cX[\ꢀ
Jg\\[ on GX^\ꢀ)*).
*% Raise and lock the headstock, so the blade is
approximately 3" from the workpiece, and open the
vise to accept the workpiece.
Note: NEVER let the saw blade rest on the workpiece
without the saw running. Otherwise, you will
permanently damage the saw blade!
+% Insert the workpiece into the vise, so the blade
will contact the flattest part of the workpiece
first, and clamp the workpiece in the vise.
8cnXpjꢀn\XiꢀjX]\kpꢀ^cXjj\jꢀn_\eꢀfg\i$
Xk`e^ꢀk_`jꢀdXZ_`e\%ꢀ=X`cli\ꢀkfꢀZfdgcpꢀ
dXpꢀi\jlckꢀ`eꢀj\i`fljꢀg\ijfeXcꢀ`ealip%
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
,% Adjust the cast iron stop for duplicate cuts and
Lock Lever
install the ejector chute if required.
-% Loosen the headstock lock lever (=`^li\ꢀ)+), and
swivel the headstock to the needed angle of cut, and
lock the lever in place.
.% Set the blade guide so the guides hold the blade
close to the workpiece, and the blade will not
twist with a cutting load (refer to 9cX[\ꢀ>l`[\j on
GX^\ꢀ(0 for detailed instructions).
/% Open the feed ON/OFF valve and turn the feed
rate knob so the feed rate is correct, based on your
observations of the blade chip characteristics. Refer
to =\\[ꢀIXk\ on GX^\ꢀ), for detailed instructions.
=`^li\ꢀ)+% Headstock swivel system.
Note: When the cut is complete, the ON/OFF switch
push lever will shut F== the bandsaw.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
9cX[\ꢀJg\\[
The Model M1013 has these three blade speeds: 80, 120,
and 200 FPM.
ꢀꢀꢀEfk\1 These suggested blade speeds
are an average for both High
Carbon Blades and Bimetal Blades.
Refer to your saw blade manufac-
turer for exact speeds.
KfꢀZ_Xe^\ꢀYcX[\ꢀjg\\[j#ꢀ[fꢀk_\j\ꢀjk\gj1
(% DISCONNECT BANDSAW FROM POWER!
Nfibg`\Z\
DXk\i`Xc
Tool Steel
Stainless Steel
Alloy Steel
Jg\\[ꢀ`eꢀ
=GD
)% Determine the best speed for your cut. The table in
=`^li\ꢀ), is provided as a basic guideline. Material
thickness and the type of blade used will factor into
FPM selection.
90
90
90
Bearing Bronze
High Carbon Steel
Medium Carbon Steel
Hard Brass
Hard Bronze
Low Carbon Steel
Soft Brass
Copper
Aluminum
Plastics
90
*% Slacken the V-belt (refer to the Glcc\pꢀ:fm\i
subsection on GX^\ꢀ(. for detailed instructions).
135
135,195
195
195
195
195
255
255
255
+% Position the V-belt on the pulleys for the desired FPM
(feet per minute), as illustrated in =`^li\ꢀ),.
,% Correctly tension the V-belt, then close and secure
the pulley cover before beginning operation.
ꢀꢀꢀEfk\1ꢀ=GDꢀ4ꢀFeet Per Minute.
Dfkfi
Glcc\p
N_\\c
Glcc\p
Jg\\[ꢀXk
-'?q
80 FPM
120 FPM
200 FPM
=`^li\ꢀ),% Blade cutting speed chart.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
9cX[\ꢀJ\c\Zk`fe
The chart below is a basic starting point for
choosing blade type based on teeth per inch
(TPI) for variable tooth pitch blades and for
standard raker type bimetal blades/HSS blades.
However, for exact specifications of bandsaw
blades, contact the blade manufacturer.
Kfꢀj\c\Zkꢀk_\ꢀZfii\ZkꢀYcX[\ꢀKG@#ꢀ[fꢀk_\j\ꢀ
jk\gj1
(% Measure the material thickness. This
measurement is the length of cut
taken from where the tooth enters the
workpiece, sweeps through, and exits the
workpiece.
Here are some general rules of thumb with
respect to bandsaw blade use.
)% Refer to the "Material Thickness" row of
the blade selection chart in =`^li\ꢀ)-, and
read across to find the workpiece thickness
you need to cut.
•
At least three teeth must contact the metal
at any phase of the cut. Otherwise, the
teeth can load up with metal, fracture, and
break off. If the TPI is too high, the teeth
can load up with material and overheat,
damaging the blade.
*% Refer to the "Shape" of metal and "Material
Type" columns, and find the shape and
material to be cut.
•
•
For a faster but rougher cut, use a blade
with a lower TPI and a higher feed rate.
+% In the applicable row, read across to the
right and find the box where the row and
column intersect. Listed in the box is the
minimum TPI recommended for the variable
tooth pitch blades, and the TPI for bimetal
raker blades in parentheses.
For a slower but smoother cut, use a blade
with more TPI and a lower feed rate.
KFFK?ꢀJ<C<:K@FE
dd
,'
.,
,&/
+&-
(''
+&-
(,'
)''
),'
*''
*,'
+''
)&*
+,'
(%,&%/
*&+
0
)&*
*&+
(%+&)%,
(%,&%/
)&*
-
(%+&)%,
*&+
) )ꢃ * *ꢃ
`eZ_
+
,
.
/
(' (( () (* (+ (, (- (. (/ (0
:LKK@E>ꢀJG<<;ꢀI8K<ꢀI<:FDD<E;8K@FE
Jg\\[ꢀ=GD
ꢂD&D`e
Jg\\[ꢀ=GD
ꢂD&D`e
Jg\\[ꢀ=GD
ꢂD&D`e
Jg\\[ꢀ=GD
ꢂD&D`e
DXk\i`Xc
DXk\i`Xc
DXk\i`Xc
DXk\i`Xc
:XiYfe
Jk\\c
(0-u*,+
ꢂ-' ꢀꢂ('/
)'*
ꢂ-)
(((u*)( =i\\ꢀDXZ_`e`e^
ꢂ*+ ꢀꢂ0/ JkX`ec\jjꢀJk\\c
(,'u)'*
ꢂ+- ꢀꢂ-)
8ccfp
Jk\\c
KffcꢀJk\\c
.,u((/
ꢂ), ꢀꢂ*-
)+-
ꢂ.,
('/u)),
ꢂ** ꢀꢂ.,
?`^_$Jg\\[
KffcꢀJk\\c
(/'u))'
ꢂ,+ ꢀꢂ-.
8e^c\
Jk\\c
>iXp
:Xjkꢀ@ife
Dfc[ꢀJk\\c
NXk\i
?Xi[\e\[
KffcꢀJk\\c
;lZk`c\
8ljk\e`k`Z
:Xjkꢀ@ife
(/'u))'
ꢂ,+ ꢀꢂ-.
)+)
ꢂ.,
-,u/,
ꢂ)' ꢀꢂ)-
:fc[$Nfib
KffcꢀJk\\c
0,u)(*
ꢂ)0 ꢀꢂ-,
K_`e
KlY\
)'*
ꢂ-)
))'u,*+
ꢂ-. ꢀꢂ(-*
/,
ꢂ)-
*)(
ꢂ0/
8cld`eld
8ccfp
?fk$Nfib
KffcꢀJk\\c
JkX`ec\jj
Jk\\c
DXcc\XYc\
:Xjkꢀ@ife
)'*u)(*
ꢂ-) ꢀꢂ-,
:fgg\i
8ccfp
))0u+/)
ꢂ.' ꢀꢂ(+.
/,$)'*
ꢂ)- ꢀꢂ-)
F`c$?Xi[\e\[
KffcꢀJk\\c
))'
ꢂ-.
:IꢀJkX`ec\jj
Jk\\c
GcXjk`Zj
=`^li\ꢀ)-% Blade selection chart.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
=\\[ꢀIXk\
The speed at which the saw blade will cut through a
workpiece is controlled by blade type and feed rate.
The feed rate is controlled by the valve lever and feed
rate dial on the hydraulic cylinder shown in =`^li\ꢀ)..
Feed Rate
Dial
Turning the valve lever in-line with the piping, as shown
in the =`^li\ꢀ)/, opens it up, which allows the fluid to
circulate and allows the head to move. Turning the valve
lever sideways or perpendicular to the piping closes it,
which locks the headstock in place.
Valve Lever
The feed rate dial controls the amount of fluid that
circulates around the hydraulic cylinder, which in turn,
controls the speed that it moves.
=`^li\ꢀ).% Feed rate dial and lever.
Kfꢀj\kꢀk_\ꢀ]\\[ꢀiXk\#ꢀ[fꢀk_\j\ꢀjk\gj1
Chips are width
of tooth, thin and
curled, and silvery:
Optimum speed and
feed rate.
(% Raise the headstock and turn the valve lever
sideways (horizontally).
)% Clamp the workpiece in the table vise.
*% Move the headstock and blade a few inches above
Chips are silvery,
thin, small, or
the workpiece.
powdery: Reduce
cutting speed or
increase feed rate.
+% With the correct saw blade installed and blade speed
selected, turn the saw ON.
,% Slowly rotate the feed rate dial to a conservative
Chips are large,
curled, blue or
feed rate until the saw begins to cut the workpiece.
brown, or smoking:
Reduce speed or
decrease feed rate.
-% Observe the chips that exit the cut, and increase
or decrease the feed rate according to the chip
characteristics (see =`^li\ꢀ)/).
=`^li\ꢀ)/% Reading chip characteristics.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
D8@EK<E8E:<
>\e\iXc
Regular periodic maintenance on your machine will
ensure its optimum performance. Make a habit of
inspecting your machine each time you use it.
:_\Zbꢀ]fiꢀk_\ꢀ]fccfn`e^ꢀZfe[`k`fejꢀXe[ꢀi\gX`iꢀfiꢀ
i\gcXZ\ꢀn_\eꢀe\Z\jjXip1
›
›
›
›
›
Loose mounting bolts.
Missing or leaking rubber toggle switch boots.
Worn or damaged cords, switches, or plugs.
Damaged V-belt.
Any other condition that could hamper the safe
operation of this machine.
D8B<ꢀ JLI<ꢀ k_Xkꢀ pfliꢀ dXZ_`e\ꢀ `jꢀ
legcl^^\[ꢀ[li`e^ꢀXccꢀdX`ek\eXeZ\ꢀgif$
Z\[li\jꢁꢀ@]ꢀk_`jꢀnXie`e^ꢀ`jꢀ`^efi\[#ꢀj\i`$
fljꢀg\ijfeXcꢀ`ealipꢀdXpꢀfZZli%
:c\Xe`e^
A
Keeping metal chips away from bandsaw mechanisms is
important to ensure that your bandsaw lasts a long time.
Use a shop vacuum or brush-off metal chips frequently.
ClYi`ZXk`fe
The gearbox and all bearings are sealed and permanently
lubricated and no scheduled lubrication is needed.
However, you must periodically lubricate adjustment
locations and bare metal surfaces. Refer to =`^li\j
)0Ç*'ꢀfor lubrication points.
ClYi`ZXk\ꢀk_\ꢀ]fccfn`e^ꢀXi\Xjꢀc`jk\[ꢀY\cfn1
=`^li\ꢀ)0% Lubrication points.
8%ꢀ 9cX[\ꢀK\ej`feꢀD\Z_Xe`jd1 Open the main blade
guard, and drop a few drops of oil on the tension
knob lead screw.
B
9%ꢀ 9cX[\ꢀXe[ꢀ>l`[\j1ꢀDrop a few drops of light machine
oil on the blade and the blade guides daily.
:%ꢀ >\Xiꢀ9fo1 Is packed with grease and should only be
D
changed if you suspect contamination.
C
E
;%ꢀ KXYc\ꢀXe[ꢀDXZ_`e\[ꢀJli]XZ\j1ꢀKeep bare metal
surfaces rust-free with regular applications of
products like SLIPIT®. For long term storage you may
want to consider products like Boeshield T-9™.
D
<%ꢀ M`j\ꢀC\X[ꢀJZi\n1ꢀDrop a few drops of light machine
oil on the vise lead screw weekly.
=`^li\ꢀ*'% Lubrication points.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
J<IM@:<
>\e\iXc
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
k\Z_$jlggfik7j_fg]fo%Y`q.
D8B<ꢀ JLI<ꢀ k_Xkꢀ pfliꢀ dXZ_`e\ꢀ `jꢀ
legcl^^\[ꢀ [li`e^ꢀ Xccꢀ j\im`Z\ꢀ gifZ\$
[li\jꢁꢀ @]ꢀ k_`jꢀ nXie`e^ꢀ `jꢀ `^efi\[#ꢀ j\i`$
fljꢀg\ijfeXcꢀ`ealipꢀdXpꢀfZZli%
9cX[\ꢀ:_Xe^\
Change the blade when it becomes dull, damaged, or
when you are using materials that require a blade of a
certain type or tooth count.
KfꢀZ_Xe^\ꢀk_\ꢀYXe[jXnꢀYcX[\#ꢀ[fꢀk_\j\ꢀjk\gj1
(% DISCONNECT BANDSAW FROM POWER!
)% Hold the headstock, un-attach the feed cylinder by
removing the cap screw, then raise the headstock to
the full vertical position (see =`^li\ꢀ*().
Feed Cylinder
Cap Screw
*% Push the safety stop in, use a screwdriver to remove
the upper and lower blade guide guards, and loosen
the blade guides (see =`^li\ꢀ*)).
=`^li\ꢀ*(% Feed cylinder cap screw.
Guide
Knob
Safety
Stop
Guide
Bolt
Blade
Guide
Guards
=`^li\ꢀ*)% Blade guide guards and
fasteners.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
+% Loosen the tension knob and slip the blade off of the
wheels.
,% Install the new blade through both blade guide
bearings and around the bottom wheel (see the
example in =`^li\ꢀ**).
-% Hold the blade around the bottom wheel with one
hand and slip it around the top wheel with the other
hand, keeping the blade between the blade guide
bearings.
Note: It is sometimes possible to flip the blade inside
out, in which case the blade will be installed in the
wrong direction. Check to make sure the blade teeth
are facing toward the workpiece after mounting on
the bandsaw. Some blades will have a directional
arrow as a guide.
=`^li\ꢀ**% Typical blade installation.
.% When the blade is around both wheels, adjust the
position so the back of the blade is against the
shoulder of the wheels.
/% Tighten the tension knob as tight as necessary so the
blade will not slip on the wheels during start up.
0% Spin the wheel by hand until the blade resumes the
previous tracking.
—If the tracking needs to be adjusted, complete the
instructions in the 9cX[\ꢀKiXZb`e^ procedure in
the next section.
('% Properly adjust the blade tension (GX^\ꢀ(/) and the
guide bearings (GX^\ꢀ(0).
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
9cX[\ꢀKiXZb`e^
The blade tracking has been properly set at the factory.
The tracking will rarely need to be adjusted if the
bandsaw is used properly.
Blade
Tension
Knob
KfꢀX[aljkꢀk_\ꢀYcX[\ꢀkiXZb`e^ꢀfeꢀk_\ꢀYXe[jXn#ꢀ[fꢀk_\j\ꢀ
jk\gj1
Hex Bolts
(% DISCONNECT BANDSAW FROM POWER!
4mm Set
Screw
)% Raise the headstock and lock it in place by pushing
in the safety stop knob.
*% Remove both blade guide assemblies.
+% Open the wheel access cover.
=`^li\ꢀ*+% Tracking adjustment controls.
,% Loosen, but do not remove the lower cap screw in
the blade wheel tilting mechanism (=`^li\ꢀ*+).
-% Adjust the tracking set screw with a 4mm hex
wrench, as shown in =`^li\ꢀ*+, then tighten the cap
screw loosened in Jk\gꢀ,.
—Tightening the set screw will move the blade closer
to the shoulder of the wheel.
—Loosening the set screw will move the blade away
from the shoulder.
.% Tension the blade.
/% Spin the wheel by hand and observe how the blade
tracks on the wheel.
—If the blade tracks along the shoulder of the wheel
(without rubbing), the blade is tracking properly
and this adjustment is completed.
—If the blade drifts away from the shoulder of the
wheel or hits the shoulder, repeat Jk\gjꢀ,$/.
0% Replace the blade guard and blade guide assemblies.
('% Adjust the blade guides as needed. Refer to 9cX[\ꢀ
>l`[\j on GX^\ꢀ(0.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
<c\Zki`ZXcꢀJX]\kpꢀ@ejkilZk`fej
These pages are current at the time of printing. However, in the spirit of improvement, we may
make changes to the electrical systems of future machines. Study this diagram carefully. If you notice
differences between your machine and these wiring diagrams, call Woodstock International Technical
Support at (360) 734-3482.
(%ꢀ J?F:Bꢀ?8Q8I;% Working on wiring that is
connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not
limited to severe burns, electrocution,
or death. Disconnect the power from
the machine before servicing electrical
components!
,%ꢀ DFKFIꢀN@I@E>% The motor wiring shown
in these diagrams is current at the time
of printing, but it may not match your
machine. Always use the wiring diagram
inside the motor junction box.
-%ꢀ DF;@=@:8K@FEJ% Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
)%ꢀ HL8C@=@<;ꢀ<C<:KI@:@8E% Due to the
inherent hazards of electricity, only a
qualified electrician should perform wiring
tasks on this machine. If you are not a
qualified electrician, get help from one
before attempting any kind of wiring job.
.%ꢀ :8G8:@KFIJ&@EM<IK<IJ% Some capacitors
and power inverters store an electrical
charge for up to five minutes after being
disconnected from the power source. To
avoid being shocked, wait at least this long
before working on these components.
*%ꢀ N@I<ꢀ:FEE<:K@FEJ% All connections must
be tight to prevent wires from loosening
during machine operation. Double-check all
wires disconnected or connected during any
wiring task to ensure tight connections.
/%ꢀ <C<:KI@:8CꢀI<HL@I<D<EKJ% You MUST
follow the electrical requirements at the
beginning of this manual when connecting
your machine to a power source.
+%ꢀ N@I<&:FDGFE<EKꢀ;8D8><% Damaged
wires or components increase the risk of
serious personal injury, fire, or machine
damage. If you notice that any wires or
components are damaged while performing
a wiring task, replace those wires or
0%ꢀ <OG<I@<E:@E>ꢀ;@==@:LCK@<J% If you are
experiencing difficulties understanding
the information included in this section,
contact our Technical Support at (360) 734-
3482.
components before completing the task.
WIRING DIAGRAM COLOR KEY
BLACK
WHITE
GREEN
RED
BLUE
YELLOW
LIGHT
BLUE
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.shopfox.biz.
YELLOW
BROWN
GRAY
BLUE
GREEN
WHITE
PURPLE
PINK
TUR-
QUOISE
ORANGE
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
wiring diagram
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
N`i`e^ꢀ;`X^iXd
Read
Page 30
JKFG
Before
Wiring
(('Mꢀ
Gfn\iꢀJlggcpꢀ
(('Mꢀꢀ
:fee\Zk`feꢀ
9Xe[jXnꢀDfkfiꢀꢀ
:XgXZ`kfiꢀ:fm\iꢀ
>i\\eꢀ
I\[ꢀ
9cXZbꢀ
Wire number
Wire Color
N_`k\ꢀ
9cXZbꢀ
ꢀꢀ
N_`k\ꢀ
9cXZbꢀ
(ꢀ4ꢀ9cXZbꢀ
)ꢀ4ꢀPꢀ \ccfn
*ꢀ4ꢀI\[ꢀ
>iXpꢀ
P\ccfnꢀ
FE&F==ꢀ
+ꢀ4ꢀ>ꢀ iXp
Kf^^c\ꢀ
Jn`kZ_ꢀ
9Xe[jXnꢀDfkfiꢀꢀ
<c\Zki`ZXcꢀ9foꢀ
))'Mꢀ
Gfn\iꢀJlggcpꢀ
))'Mꢀꢀ
:fee\Zk`feꢀ
9Xe[jXnꢀDfkfiꢀꢀ
:XgXZ`kfiꢀ:fm\iꢀ
>i\\eꢀ
I\[ꢀ
9cXZbꢀ
Wire number
Wire Color
>iXpꢀ
N_`k\ꢀ
9cXZbꢀ
N_`k\ꢀ
9cXZbꢀ
(ꢀ4ꢀ9cXZbꢀ
)ꢀ4ꢀP\ccfn
*ꢀ4ꢀI\[ꢀ
ꢀꢀ
P\ccfnꢀ
FE&F==ꢀ
+ꢀ4ꢀ>ꢀ iXp
Kf^^c\ꢀ
Jn`kZ_ꢀ
9Xe[jXnꢀDfkfiꢀꢀ
<c\Zki`ZXcꢀ9foꢀ
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
KiflYc\j_ffk`e^
This section covers the most common problems and corrections with this type of
machine. N8IE@E>ꢁꢀ;FꢀEFKꢀdXb\ꢀXepꢀX[aljkd\ekjꢀlek`cꢀgfn\iꢀ`jꢀ[`jZfee\Zk\[ꢀXe[ꢀ
dfm`e^ꢀgXikjꢀ_Xm\ꢀZfd\ꢀkfꢀXꢀZfdgc\k\ꢀjkfgꢁ
GIF9C<D
GFJJ@9C<ꢀ:8LJ<
:FII<:K@M<ꢀ8:K@FE
Machine does not start or a 1. Plug/receptacle is at fault or wired 1. Test for good contacts; correct the wiring.
breaker trips.
incorrectly.
2. Start capacitor is at fault.
2. Test/replace if faulty.
3. Wall fuse/circuit breaker is blown/ 3. Ensure correct size for machine load; replace weak
tripped.
breaker.
4. Motor connection wired incorrect- 4. Correct motor wiring connections.
ly.
5. Power supply is at fault/switched 5. Ensure hot lines have correct voltage on all legs and
OFF.
main power supply is switched ON.
6. Replace faulty ON/OFF switch.
6. Motor ON/OFF switch is at fault.
7. Wiring is open/has high resistance.
8. Motor is at fault.
7. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.
8. Test/repair/replace.
Machine stalls or is under- 1. Wrong blade for the workpiece 1. Use blade with correct properties for your type of
powered.
material.
cutting.
2. Wrong workpiece material.
2. Use metal with correct properties for your type of
cutting.
3. Feed rate/cutting speed too fast 3. Decrease feed rate/cutting speed.
for task.
4. Blade is slipping on wheels.
5. Low power supply voltage.
6. Motor bearings are at fault.
4. Adjust blade tracking and tension.
5. Ensure hot lines have correct voltage on all legs.
6. Test by rotating shaft; rotational grinding/loose
shaft requires bearing replacement.
7. Plug/receptacle is at fault.
7. Test for good contacts; correct the wiring.
8. Motor connection is wired incor- 8. Correct motor wiring connections.
rectly.
9. Motor has overheated.
10. Motor is at fault.
9. Clean off motor, let cool, and reduce workload.
10. Test/repair/replace.
Machine has vibration or 1. Motor fan is rubbing on fan cover. 1. Replace dented fan cover; replace loose/damaged
noisy operation.
fan.
2. Blade is at fault.
3. Gearbox is at fault.
2. Replace/resharpen blade.
3. Rebuild gearbox for bad gear(s)/bearing(s).
4. Wrong blade & too slow of speed. 4. Change blade and or speed.
Machine is loud when cut- 1. Excessive feed rate.
1. Refer to Feed Rate on Page 25, or Blade Speed on
Page 23, and adjust as required.
ting or bogs down in the
cut.
2. The blade TPI is too great, or the 2. Refer to Blade Selection on Page 24 and adjust as
material is too coarse. required.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
GIF9C<D
Blades break often.
GFJJ@9C<ꢀ:8LJ<
1. Blade is not tensioned correctly.
:FII<:K@M<ꢀ8:K@FE
1. Check to see that blade is not excessively tight or
too loose.
2. The workpiece is loose in the vise. 2. Clamp the workpiece tighter, or use a jig to hold the
workpiece.
3. The feed or cut speed is wrong.
3. Refer to Feed Rate on Page 25, or Blade Speed on
Page 23, and adjust as required.
4. The blade TPI is too great, or the 4. Refer to Blade Selection on Page 24 and adjust as
material is too coarse.
required.
5. The blade is rubbing on the wheel 5. Refer to Blade Tracking on Page 29, and adjust as
flange.
required.
6. The bandsaw is being started 6. Start bandsaw and then slowly lower the headstock
with the blade resting on the
workpiece.
by setting the feed rate.
7. The guide bearings are misaligned, 7. Refer to Blade Tracking on Page 29, or Blade Guides
or the blade is rubbing on the
wheel flange.
on Page 19 and adjust as required.
8. The blade is too thick, or the 8. Use a higher quality blade.
blades are of low quality.
Blade dulls prematurely.
1. The cutting speed is too fast.
1. Refer to Blade Speed on Page 23, and adjust as
required.
2. The blade TPI is too coarse.
2. Refer to Blade Selection on Page 24, and adjust as
required.
3. The blade feed pressure is too 3. Refer to Feed Rate on Page 25, and adjust as
light.
required.
4. The workpiece has hard spots, 4. Increase the feed pressure, and reduce the cutting
welds, or scale is on the material.
5. The blade is twisted.
speed.
5. Replace the blade.
6. The blade is slipping on the 6. Refer to Blade Tension on Page 18, and adjust as
wheels.
required.
1. The blade guides are worn or mis- 1. Refer to Blade Guides on Page 19 and replace or
adjusted. adjust.
Blade wears on one side.
2. The blade guide slide bracket is 2. Tighten the blade guide bracket.
loose.
3. The wheels are out of alignment.
3. Refer to Blade Tracking on Page 29, and adjust as
required.
Teeth are ripping from the 1. The feed pressure is too heavy and 1. Refer to Blade Selection on Page 24 and decrease
blade.
the blade speed is too slow; or
the blade TPI is too coarse for the
workpiece.
the feed pressure. Refer to Feed Rate on Page 25,
and adjust as required.
2. The workpiece is vibrating in the 2. Re-clamp the workpiece in the vise, and use a jig if
vise. required.
3. The blade gullets are loading up 3. Use a coarser-tooth blade.
with chips.
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
G8IKJ
Dfkfiꢀꢄꢀ=\\[ꢀIXk\ꢀ:fekifc
/
,
0
-
($)
+
($(
*
.
($*
(
)
($+
((
('
()
(*
*0
*)
+'8
(+
(,
+(
(-
(0
*(
+*8
(/
(.
)*
*'
)+8
),
)'
)(
).
))8
)/
)0
)-8
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
Dfkfiꢀꢄꢀ=\\[ꢀIXk\ꢀ:fekifcꢀGXikjꢀC`jk
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
XM1013001 MOTOR 1/2HP 110/220V 1PH
17
18
19
20
21
XPN08
XM1013018 BRACKET
XM1013019 HANDLE
XPCAP97
XPN13
HEX NUT 3/8-16
1-1 XM1013001-1 MOTOR FAN COVER
1-2 XM1013001-2 MOTOR FAN
1-3 XM1013001-3 CAPACITOR COVER
1-4 XM1013001-4 S CAPACITOR 200M 125V
CAP SCREW 1/2-12 X 2-1/2
HEX NUT 1/2-13
2
3
4
5
XM1013002 MOTOR PULLEY
22A XM1013022A SPECIAL BOLT 3/8"-16 X 1 3/4"
23 XM1013023 BUSHING 19 X 17 X 7
24A XM1013024A SWITCH BASE V2.10.06
25 XPS06 PHLP HD SCR 10-24 X 3/8
26A XM1013026A SWITCH BOX V2.08.06
XPK12M
XPSS17
XPHTEK11
KEY 5 X 5 X 30
SET SCREW 5/16-18 X 5/16
TAP SCREW 1/4 X 5/16(3/4)
6
XM1013006 BELT COVER
7
8
9
10
11
12
13
14
15
16
XPS04
PHLP HD SCR 1/4-20 X 1/2
27
28
29
30
31
32
39
XM1013027 SUPPORT ROD
XM1013008 MOTOR CABLE
XM1013009 POWER CABLE
XPB03
XPB07
XPW07
XM1013013 PIVOT
XM1013014 KNOB BOLT 1/4-20 X 5/8
XM1013015 SPECIAL PIN 10 X 38.5 MM
XPW03
XPS06
FLAT WASHER #10
PHLP HD SCR 10-24 X 3/8
HEX BOLT 5/16-18 X 1
HEX BOLT 5/16-18 x 3/4
FLAT WASHER 5/16
XM1013030 CYLINDER ASSEMBLY
XPSS04 SET SCREW 1/4-20 X 5/16
XM1013032 PIVOTING ROD
XPCAP05 CAP SCREW 1/4-20 X 3/4
40A XM1013040A CYLINDER UPPER SUPPORT V2.10.06
41 XPLW01 LOCK WASHER 5/16
43A XM1013043A SPECIAL CAP SCREW V2.10.06
XPB58
HEX BOLT 3/8-16 X 2
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
JXnꢀ8jj\dYcp
J\\ꢀGX^\ꢀ+'
J\\ꢀGX^\ꢀ+'
((,
(',
(-+
(('
('0
('.
(*,
(*-
('+
(((
(*.
(*+
(*'
(()
((,
((-
((.
((/
((*
((+
(')
(''
(*.
(*)
()+
()*
(*(
((-
(*/
(*0
(+'
((0
(+(
()(
()0
()/
()(
()'
(('
(+,8
().
()-
(++
(+.
J\\ꢀGX^\ꢀ+'
J\\ꢀGX^\ꢀ+'
(+/
()-
(,'
(,(
(,-
()(
(,)
(,*
(,+
()-
(,0
(-'
(-(
(-)8
J\\ꢀGX^\ꢀ+'
(-*
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
JXnꢀ8jj\dYcpꢀGXikjꢀC`jk
REF PART #
XM1013100
DESCRIPTION
REF PART #
DESCRIPTION
100
102
104
105
107
109
110
111
112
113
114
115
116
117
118
119
120
121
123
124
126
127
128
129
130
131
BODY FRAME
132
134
135
136
137
138
139
140
141
144
XPN02
HEX NUT 5/16-18
XPB41
HEX BOLT 1/2-12 X 1-1/2
GEAR BOX GASKET
PLATE
V-BELT A-23
PULLEY
XM1013134
XM1013135
XPB07
XPW07
XPN08
XM1013139
XPCAP04
XPB24
MOTOR MOUNT PLATE
KNOB BOLT 5/16-18 X 1-3/4
HEX BOLT 5/16-18 x 3/4
FLAT WASHER 5/16
XM1013104
XM1013105
XPVA23
XM1013109
XM1013110
XM1013111
XPS24
XPB03
XPB07
XPB02
XM1013116
XPW07
XM1013118
XM1013119
XM1013120
XPW02
XM1013123
XPSS38
HEX NUT 3/8-16
BEARING COVER
OIL SEAL
SWITCH CUT OFF TIP
CAP SCREW 1/4-20 X 1/2
HEX BOLT 3/8-16 X 1-1/4
RIGHT SAFETY GUARD (OPTION)
PHLP HD SCR 8-32 X 3/8
HEX BOLT 5/16-18 X 1
HEX BOLT 5/16-18 x 3/4
HEX BOLT 1/4-20 X 5/8
BLADE TENSION SLIDING GUIDE
FLAT WASHER 5/16
SHAFT BLOCK
COMPRESSION SPRING
BLADE TENSION KNOB
FLAT WASHER 3/8
BLADE TENSION SLIDING PLATE
SET SCREW 5/16-18 X 5/8
PHLP HD SCR M5-.8 X 12
BUSHING
XM1013144
145A XM1013145A STOP BOLT 3/8-16 X 1 V2.10.06
147
148
150
151
152
153
154
156
159
160
161
XPK23M
XM1013148
XPR05M
XPSS17
XPW07
KEY 5 X 5 X 25
FRONT BLADE WHEEL
EXT RETAINING RING 15MM
SET SCREW 5/16-18 X 5/16
FLAT WASHER 5/16
HEX BOLT 5/16-18 x 3/4
BLADE 1/2" X 0.025" X 64-1/2"
KNOB BOLT 3/8-16 X 1-1/4
LEFT SAFETY GUARD
XPB07
XM1013154
XM1013156
XM1013159
XM1013160
XPW06
XPS08M
KNOB BOLT 1/4"-20 X 5/8"
FLAT WASHER 1/4
XM1013127
XPCAP05
XPN05
XM1013130
XPS06
CAP SCREW 1/4-20 X 3/4
HEX NUT 1/4-20
WIRE CLAMP
162A XM1013162A PLASTIC SAFETY COVER V2.08.06
163
164
XPS06
XPSS17M
PHLP HD SCR 10-24 X 3/8
SET SCREW M8-1.25 X 6
PHLP HD SCR 10-24 X 3/8
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
JkXe[ꢀ8jj\dYcp
)*,ꢀ
)*+ꢀ
)**8
)*)8
)*(ꢀ
)*'ꢀ
)*-ꢀ
)).ꢀ
))08
))/8
)(0ꢀ
))-ꢀ
)),ꢀ
))*8ꢀ
)')ꢀ
)'*ꢀ
)'+ꢀ
)))ꢀ
))'ꢀ
))(ꢀ
)''ꢀ
)()ꢀ
)(*ꢀ
)((ꢀ
)('ꢀ
)'0ꢀ
)'/ꢀ
)(+$-
)(+ꢀ
)(-ꢀ
)(.ꢀ
)(/$(ꢀ
)(,ꢀ
)(/$(ꢀ
**/
)(/ꢀ
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
JkXe[ꢀ8jj\dYcpꢀGXikjꢀC`jk
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
200
202
203
204
208
209
210
211
212
213
214
XM1013200
XPB26M
BASE
220
221
222
XM1013220
XPCAP30
XPS04
PLATE
HEX BOLT M8-1.25 X 30
LOCK WASHER 8MM
SCALE
CAP SCREW 5/16-18 X 1/2
PHLP HD SCR 1/4-20 X 1/2
XPLW04M
XM1013204
XM1013208
XPSS17
XM1013210
XM1013211
XPW03M
223A XM1013223A BRACKET W/NUT V2.01.08
EJECTOR PLATE
225
226
227
XPSS03
XM1013226
XPLW01
SET SCREW 1/4-20 X 3/8
BUSHING
LOCK WASHER 5/16
SET SCREW 5/16-18 X 5/16
DISTANCE SET BRACKET
STOCK STOP ROD 1/2"
FLAT WASHER 6MM
PHLP HD SCR M6-1 X 12
DELUXE STAND ASSEMBLY
228A XM1013228A ACME SCREW V2.01.08
229A XM1013229A VISE BASE V2.01.08
230
231
XPS14M
XM1013214
XPW07
XPCAP69
FLAT WASHER 5/16
CAP SCREW 5/16-18 X 1/4
214-6 XM1013214-6 SHOP FOX LOGO 2-5/16" X 5"
232A XM1013232A VICE HALF V2.01.08
233A XM1013233A WALL PLATE V2.01.08
215
216
217
218
XM1013215
XM1013216
XM1013217
XM1013218
RUBBER FOOT
WHEEL ROD
COTTER PIN 1/8 X 1
WHEEL
234
235
236
338
XPW07
XPB07
XPCAP08
XM1013338
FLAT WASHER 5/16
HEX BOLT 5/16-18 x 3/4
CAP SCREW 5/16-18 X 1-1/2
STRIPE FOR STAND 6" X 4'
218-1 XPW27MM
219 XM1013219
FLAT WASHER 17MM
HANDWHEEL ASSEMBLY
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
guides and shafts
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
>l`[\jꢀꢄꢀJ_X]kj
*)0ꢀ
*(.ꢀ
*(/ꢀ
*(.ꢀ
*(/ꢀ
*(-ꢀ
*(,ꢀ
***ꢀ
**+ꢀ
**)ꢀ
**,ꢀ
**+ꢀ
***ꢀ
*).ꢀ
*))ꢀ
**,ꢀ
*))ꢀ
*).ꢀ
**(ꢀ
*)*ꢀ
*)+ꢀ
*).ꢀ
*)-ꢀ
*)*ꢀ
**'ꢀ
*).ꢀ
*)-ꢀ
*)+ꢀ
*'*M)
*'+
*')M)
*'(M)
**0
*+'
**0
*''M)
*',ꢀ
*'-ꢀ
*(*ꢀ
*'/ꢀ
*'.ꢀ
*'0ꢀ
*(0ꢀ
*'0ꢀ
*('ꢀ
*()ꢀ
*'0ꢀ
-40-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
>l`[\jꢀꢄꢀJ_X]kjꢀGXikjꢀC`jk
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
300V2 XM1013300V2 REAR BLADE WHEEL V2.06.09
301V2 XM1013301V2 BUSHING V2.06.09
302V2 XM1013302V2 BLADE WHEEL SHAFT V2.06.09
303V2 XM1013303V2 AXLE BLOCK V2.06.09
318
319
322
323
324
326
327
329
330
331
332
333
334
335
339
340
XPLW04
LOCK WASHER 3/8
WORM GEAR SHAFT
SPECIAL PIN 10 X 40MM
GUIDE ECCENTRIC
GUIDE SHAFT
XM1013319
XM1013322
XM1013323
XM1013324
XPR01M
304
305
306
307
308
309
310
312
313
315
316
317
XPRP39M
XM1013305
XPRP20M
XM1013307
XPK23M
ROLL PIN 4 X 20
WORM GEAR
ROLL PIN 4 X 22
TRANSMISSION WHEEL SHAFT
KEY 5 X 5 X 25
EXT RETAINING RING 10MM
XP6000-OPEN BALL BEARING 6000 OPEN
XM1013329
XM1013330
XPFH03
XM1013332
XPB03
XPLW01
XPW07
XP6202ZZ
XM1013340
RIGHT ADJUSTABLE BRACKET
STOP PLATE
XP6202-OPEN BALL BEARING 6202 OPEN
FLAT HD SCR 1/4-20 X 1/2
REAR GUIDE CASTING
HEX BOLT 5/16-18 X 1
LOCK WASHER 5/16
FLAT WASHER 5/16
BALL BEARING 6202 ZZ
BUSHING
XM1013310
XM1013312
XM1013313
XM1013315
XM1013316
XPN08
BUSHING
SEAL
BUSHING
LEFT ADJUSTABLE BRACKET
FRONT GUIDE CASTING
HEX NUT 3/8-16
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
DXZ_`e\ꢀCXY\cj
JX]\kpꢀcXY\cjꢀnXieꢀXYflkꢀdXZ_`e\ꢀ_XqXi[jꢀXe[ꢀ_fnꢀkfꢀgi\m\ekꢀdXZ_`e\ꢀ[XdX^\ꢀfiꢀ`ealip%ꢀK_\ꢀ
fne\iꢀf]ꢀk_`jꢀdXZ_`e\ꢀDLJKꢀdX`ekX`eꢀk_\ꢀfi`^`eXcꢀcfZXk`feꢀXe[ꢀi\X[XY`c`kpꢀf]ꢀXccꢀcXY\cjꢀfeꢀk_`jꢀ
dXZ_`e\%ꢀ@]ꢀXepꢀcXY\cꢀ`jꢀi\dfm\[ꢀfiꢀY\Zfd\jꢀlei\X[XYc\#ꢀI<GC8:<ꢀk_XkꢀcXY\cꢀY\]fi\ꢀXccfn`e^ꢀk_\ꢀ
dXZ_`e\ꢀkfꢀ\ek\iꢀj\im`Z\ꢀX^X`e%ꢀ:fekXZkꢀNff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢀXkꢀ(*-')ꢀ.*+$*+/)ꢀfiꢀnnn%
j_fg]fokffcj%Zfdꢀkfꢀfi[\iꢀe\nꢀcXY\cj%ꢀ
400
402
403
401
404
405
408
407
405
406
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
400 XM1013400 MACHINE ID LABEL
405 XPLABLE-14B ELECTRICITY LABEL
401 XM1013401 SAFETY GLASSES LABEL
402 XM1013402 DISCONNECT POWER LABEL
403 XM1013403 AMPUTATION HAZARD LABEL
404 XPPAINT-7 SHOPFOX BLACK TOUCH-UP PAINT
406 XPPAINT-1
407 XM1013123-1 BLADE TENSION LABEL
408 XPLABEL-12A READ MANUAL LABEL
SHOPFOX WHITE TOUCH-UP PAINT
-42-
Download from Www.Somanuals.com. All Manuals Search And Download.
D('(*ꢀFne\iꢁjꢀDXelXcꢀꢂD]^%ꢀJ`eZ\ꢀ-&'0
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
NFF;JKF:Bꢀ@EK<IE8K@FE8Cꢀ@E:%ꢀ
G%F%ꢀ9FOꢀ)*'0ꢀ
9<CC@E>?8D#ꢀN8ꢀ0/)).$)*'0
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
N8II8EKP
N8II8EKP
Nff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢀnXiiXekjꢀXccꢀJ_fgꢀ=foꢀdXZ_`e\ipꢀkfꢀY\ꢀ]i\\ꢀf]ꢀ[\]\Zkjꢀ]ifdꢀnfibdXej_`gꢀ
Xe[ꢀdXk\i`Xcjꢀ]fiꢀXꢀg\i`f[ꢀf]ꢀknfꢀp\Xijꢀ]ifdꢀk_\ꢀ[Xk\ꢀf]ꢀfi`^`eXcꢀgliZ_Xj\ꢀYpꢀk_\ꢀfi`^`eXcꢀfne\i%ꢀ
K_`jꢀnXiiXekpꢀ[f\jꢀefkꢀXggcpꢀkfꢀ[\]\Zkjꢀ[l\ꢀ[`i\Zkcpꢀfiꢀ`e[`i\Zkcpꢀkfꢀd`jlj\#ꢀXYlj\#ꢀe\^c`^\eZ\ꢀfiꢀ
XZZ`[\ekj#ꢀcXZbꢀf]ꢀdX`ek\eXeZ\#ꢀfiꢀi\`dYlij\d\ekꢀf]ꢀk_`i[ꢀgXikpꢀ\og\ej\jꢀ`eZlii\[%ꢀ
Nff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢀn`ccꢀi\gX`iꢀfiꢀi\gcXZ\#ꢀXkꢀ`kjꢀ\og\ej\ꢀXe[ꢀXkꢀ`kjꢀfgk`fe#ꢀk_\ꢀJ_fgꢀ=foꢀ
dXZ_`e\ꢀfiꢀdXZ_`e\ꢀgXik#ꢀn_`Z_ꢀ`eꢀefidXcꢀlj\ꢀ_Xjꢀgifm\eꢀkfꢀY\ꢀ[\]\Zk`m\#ꢀgifm`[\[ꢀk_Xkꢀk_\ꢀfi`^`eXcꢀ
fne\iꢀi\kliejꢀk_\ꢀgif[lZkꢀgi\gX`[ꢀkfꢀXꢀJ_fgꢀ=foꢀ]XZkfipꢀj\im`Z\ꢀZ\ek\iꢀn`k_ꢀgiff]ꢀf]ꢀk_\`iꢀgliZ_Xj\ꢀ
f]ꢀk_\ꢀgif[lZkꢀn`k_`eꢀknfꢀp\Xij#ꢀXe[ꢀgifm`[\jꢀNff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢀi\XjfeXYc\ꢀfggfikle`kpꢀkfꢀ
m\i`]pꢀk_\ꢀXcc\^\[ꢀ[\]\Zkꢀk_ifl^_ꢀ`ejg\Zk`fe%ꢀ@]ꢀ`kꢀ`jꢀ[\k\id`e\[ꢀk_\i\ꢀ`jꢀefꢀ[\]\Zk#ꢀfiꢀk_Xkꢀk_\ꢀ[\]\Zkꢀ
i\jlck\[ꢀ]ifdꢀZXlj\jꢀefkꢀn`k_`eꢀk_\ꢀjZfg\ꢀf]ꢀNff[jkfZbꢀ@ek\ieXk`feXcꢀ@eZ%ꢄjꢀnXiiXekp#ꢀk_\eꢀk_\ꢀfi`^`eXcꢀ
fne\iꢀdljkꢀY\Xiꢀk_\ꢀZfjkꢀf]ꢀjkfi`e^ꢀXe[ꢀi\klie`e^ꢀk_\ꢀgif[lZk%ꢀ
K_`jꢀ`jꢀNff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢄjꢀjfc\ꢀni`kk\eꢀnXiiXekpꢀXe[ꢀXepꢀXe[ꢀXccꢀnXiiXek`\jꢀk_XkꢀdXpꢀ
Y\ꢀ`dgc`\[ꢀYpꢀcXn#ꢀ`eZcl[`e^ꢀXepꢀd\iZ_XekXY`c`kpꢀfiꢀ]`ke\jj#ꢀ]fiꢀXepꢀgXik`ZlcXiꢀgligfj\#ꢀXi\ꢀ_\i\Ypꢀ
c`d`k\[ꢀkfꢀk_\ꢀ[liXk`feꢀf]ꢀk_`jꢀni`kk\eꢀnXiiXekp%ꢀN\ꢀ[fꢀefkꢀnXiiXekꢀk_XkꢀJ_fgꢀ=foꢀdXZ_`e\ipꢀZfdgc`\jꢀ
n`k_ꢀk_\ꢀgifm`j`fejꢀf]ꢀXepꢀcXnꢀfiꢀXZkj%ꢀ@eꢀefꢀ\m\ekꢀj_XccꢀNff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢄjꢀc`XY`c`kpꢀle[\iꢀ
k_`jꢀnXiiXekpꢀ\oZ\\[ꢀk_\ꢀgliZ_Xj\ꢀgi`Z\ꢀgX`[ꢀ]fiꢀk_\ꢀgif[lZk#ꢀXe[ꢀXepꢀc\^XcꢀXZk`fejꢀYifl^_kꢀX^X`ejkꢀ
Nff[jkfZbꢀ@ek\ieXk`feXc#ꢀ@eZ%ꢀj_XccꢀY\ꢀki`\[ꢀ`eꢀk_\ꢀJkXk\ꢀf]ꢀNXj_`e^kfe#ꢀ:flekpꢀf]ꢀN_XkZfd%ꢀN\ꢀj_Xccꢀ
`eꢀefꢀ\m\ekꢀY\ꢀc`XYc\ꢀ]fiꢀ[\Xk_#ꢀ`eali`\jꢀkfꢀg\ijfejꢀfiꢀgifg\ikpꢀfiꢀ]fiꢀ`eZ`[\ekXc#ꢀZfek`e^\ek#ꢀjg\Z`Xcꢀfiꢀ
Zfej\hl\ek`Xcꢀ[XdX^\jꢀXi`j`e^ꢀ]ifdꢀk_\ꢀlj\ꢀf]ꢀfliꢀgif[lZkj%ꢀ
<m\ipꢀ\]]fikꢀ_XjꢀY\\eꢀdX[\ꢀkfꢀ\ejli\ꢀk_XkꢀXccꢀJ_fgꢀ=foꢀdXZ_`e\ipꢀd\\kjꢀ_`^_ꢀhlXc`kpꢀXe[ꢀ[liXY`c`kpꢀ
jkXe[Xi[j%ꢀN\ꢀi\j\im\ꢀk_\ꢀi`^_kꢀkfꢀZ_Xe^\ꢀjg\Z`]`ZXk`fejꢀXkꢀXepꢀk`d\ꢀY\ZXlj\ꢀf]ꢀfliꢀZfdd`kd\ekꢀkfꢀ
Zfek`elfljcpꢀ`dgifm\ꢀk_\ꢀhlXc`kpꢀf]ꢀfliꢀgif[lZkj%
Download from Www.Somanuals.com. All Manuals Search And Download.
=^\]ꢀFjVa^inꢀBVX]^cZhꢀVcYꢀIddah
LddYhidX`ꢀ>ciZgcVi^dcVa!ꢀ>cX#ꢀXVgg^Zhꢀi]djhVcYhꢀd[ꢀegdYjXihꢀYZh^\cZYꢀ
ꢀidꢀbZZiꢀi]ZꢀcZZYhꢀd[ꢀidYVnꢁhꢀlddYldg`ZghꢀVcYꢀbZiValdg`Zgh#ꢀ
6h`ꢀndjgꢀYZVaZgꢀVWdjiꢀi]ZhZꢀ[^cZꢀegdYjXih/ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Weed Eater Trimmer 530163507 User Manual
Whirlpool Freezer EV161FZRQ00 User Manual
Whirlpool Ventilation Hood RH2630XJ User Manual
White Outdoor Tiller 217 310 190 User Manual
White Rodgers Thermostat 1F81 71 User Manual
White Rodgers Weather Radio 259 6 User Manual
Woodstock Paint Sprayer D3274 User Manual
Zanussi Plumbing Product 132706 User Manual
Zanussi Range ZCM 620 X User Manual
Zenith CRT Television 206 3923 User Manual