SGO
Series 3 Oil-Fired Steam Boiler
Maintenance
and Service
Guide
For future reference, leave this manual
with other boiler instructions
in the envelope provided with the boiler.
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
ForYour Safety
Tips for steam systems:
Follow instructions below to
prevent severe personal injury, death or substan-
tial property damage:
Check boiler and system piping for leaks.
Continual makeup water will reduce boiler life.
Minerals can build up in sections, reducing
heat transfer and causing cast iron to overheat,
resulting in section failure.
●
●
Do not use crankcase drainings or any oil
containing gasoline. See burner manual for
proper fuel oil.
●
Do not attempt to start burner when excess
oil has accumulated in combustion chamber,
when unit is full of vapor, or when combus
tion chamber is very hot.
Failure to maintain recom-
mended pH and to repair leaks can cause
section iron corrosion, leading to section
failure and leaks. Do not use petroleum-
based sealing or stop-leak compounds in
boiler systems. Damage to system components
can result.
●
Donotstartburnerunlesscollectorhood,flue
cap, jacket cap, breeching and burner mount-
ing door are secured in place.
Never burn garbage or paper in the boiler.
Never leave combustible material around
boiler.
DO NOT TAMPER WITH UNIT OR CONTROLS.
Always follow specific instructions when
starting up boiler or performing routine
maintenance or service.
●
●
Boiler water pH 7.0 to 8.5 is recommended.
For pH conditions outside 7.0 to 8.5 range or
unusually hard water areas (above 7 grains
hardness), consult local water treatment
company.
●
●
●
●
Do not add cold water to hot boiler. Thermal
shock can cause sections to crack.
Clean newly installed steam boiler to remove
oil, grease, and other foreign material. Failure
to properly clean can result in violent water
level fluctuations, water passing into steam
mains, or high maintenance costs on strainers,
traps and and vents. A qualified service techni-
cian should skim the boiler by following
Follow instructions below to
prevent severe personal injury, death or substan-
tial property damage:
●
To avoid electric shock, turn off electrical
supply at switch on boiler and additional
external switches before performing service.
●
To avoid severe burns, allow boiler to cool
instructions on page 10 of this manual.
before performing service.
●
Do not block flow of combustion or ventilation
air to boiler.
Boiler must be connected to a flue with
●
sufficient draft at all times to assure proper
operation.
Do not use this boiler if any part has been
●
under water. Electrical and mechanical
failures may cause electric shock and fire
risks. Immediately call a qualified service
technician to inspect chimney or vent,
boiler and burner. Have the boiler flueways
cleaned and have the following replaced:
— all electrical and mechanical controls
— electrical wiring
— oil burner and controls
— insulation and chamber lining
3
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Routine Maintenance Schedule
The schedule below is specifically designed for the homeowner.
Please read pages 2 and 3 before proceeding.
Periodically during heating season:
Beginning each heating season:
Probe-type low water cutoff, when used:
Call a qualified service technician to perform
annual service.
Refer to control manufacturer's instructions
for testing.
Daily during heating season:
End of heating season:
Check that boiler area is free from combusti-
ble materials, gasoline and other flammable
vapors and liquids.
If tankless heater is installed, boiler will
continue to operate. Check for the following:
-
-
All daily, weekly and monthly instructions
listed on this page must be followed.
Burner motor may have to be oiled. Some
motors are permanently lubricated and do
Weekly during heating season:
Checkforandremoveanyobstructionstoflow
of combustion or ventilation air to boiler.
not
need additional oil. Check for oiling
instructions on burner or motor.
Check that breeching is attached between
boiler and chimney. If breeching is loose or
damaged, immediately turn off switch on front
of boiler and call qualified service technician
to repair.
Boiler shutdown:
Do not drain boiler unless exposure to
freezing temperatures will occur.
Do not use antifreeze in steam systems.
Always keep manual fuel supply shut off if
burner is shut down for an extended period of
time.
●
●
●
Check for oil leaks in oil piping and around
burner. If found, immediately call qualified
service technician to correct situation.
a. Turn off switch at boiler and any external
switch to boiler.
b. Close fuel valves.
c. Turn off water feed valve.
d. Cover burner to protect from dust and
dampness.
Check for water leaks in boiler and piping;
also check for leaks around tankless heater
plate. If found, immediately call qualified
service technician to repair.
Float-type low water cutoff, when used:
Refer to control manufacturer's instructions.
Scald potential. Do not blow
down low water cutoff unless blowdown
piping has been installed according to Boiler
Manual. If piping is not in place, call qualified
service technician to install.
4
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up
2. Correct problems found in step #1. If burner
does not fire, press reset button on burner
primary control only once. Repeated presses
will deposit oil in combustion chamber.
SGO with float-type low water cutoff:
1. If burner does not fire, check for:
Switch on boiler or additional shut-off
switches turned off.
●
Burner must never be fired
when oil is in combustion chamber. Immedi-
ately call qualified service technician.
●
●
Fuses or breaker switch tripped.
Thermostat set below room temperature.
Fuel valves turned off.
Not enough oil in tank to supply burner.
No water in gauge glass.
●
3. If burner still does not fire, call qualified
service technician.
●
●
Steam ReliefValve
(on back of boiler)
Gauge Glass
Tankless Heater
Control
Located in tankless heater
plate (sizes 3-5)
or in tapping in back
section (sizes 6-9)
Pressure Control
Pressure Gauge
Service Switch
on Boiler
Reset Button on
Burner Primary
Control
Float-Type
LowWater
Cutoff
Burner Primary
Control
Burner
Disconnect
Plug
SGO Boiler with Float-Type LowWater Cutoff
(See Page 6 for Probe-Type LowWater Cutoff)
Figure 1
5
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up
2. Correct problems found in step #1. If burner
does not fire, press reset button on burner
primary control only once. Repeated presses
will deposit oil in combustion chamber.
SGO with probe-type low water cutoff:
1. If burner does not fire, check for:
Service switch on boiler or additional
switches turned off.
Fuses or breaker switch tripped.
Thermostat set below room temperature.
●
Burner must never be fired
when oil is in combustion chamber. Immedi-
ately call qualified service technician.
●
●
Fuel valves turned off.
Not enough oil in tank to supply burner.
No water in gauge glass.
●
3. If burner still does not fire, call qualified
service technician.
●
●
Steam ReliefValve
(on back of boiler)
Pressure Control
Pressure Gauge
Tankless Heater
Control
Located in tankless heater
plate (sizes 3-5)
or in tapping in back
section (sizes 6-9)
Probe-Type
LowWater
Cutoff
Service Switch
on Boiler
Reset Button on
Burner Primary
Control
Gauge Glass
Burner Primary
Control
Burner
Disconnect
Plug
SGO Boiler with Probe-Type LowWater Cutoff
(See Page 5 for Float-Type LowWater Cutoff)
Figure 2
6
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
COMMON PROBLEMS
COMMON CAUSES
POSSIBLE CORRECTIONS
Rapid cycling - burner turns
on and off frequently.
Thermostat installed where drafts or
heat affect reading.
Locate thermostat on inner wall away from
heat sources or cool drafts.
Heat anticipator in thermostat
adjusted incorrectly.
Adjust heat anticipator to match current
draw. Refer to boiler wiring diagram.
Incorrect limit setting.
Have qualified service technician increase
limit setting to decrease cycling. Normal
operation is usually less than 5 psig.
Need to frequently add
makeup water.
Leaks in boiler or piping.
Have qualified service technician repair leaks
at once to avoid constant use of makeup
water.
Popping or percolating noise
heard in boiler.
Mineral deposits in sections due to
constant use of makeup water. or
incorrect pH.
Have qualified service technician de-lime
boiler and repair leaks at once to avoid
constant use of makeup water and check
pH (7.0-8.5).
Metal flakes found in flueway.
Contaminated combustion air supply.
Remove sources of hydrocarbons in or
near boiler area. (Bleaches, cleaners,
chemicals, sprays, fabric softeners, paint
remover, etc.)
Condensation of combustion gases.
Air vents or traps inoperative.
Incorrect Hartford Loop piping.
Check-valve inoperative.
Have qualified service technician check
boiler operation.
Isolated radiation does not
heat.
Have qualified service technician repair,
clean or replace air vents or traps.
Water disappearing from
gauge glass and back into
system through return piping.
Have qualified service technician pipe boiler
exactly as shown in Boiler Manual.
Have qualified service technician clean or
replace check-valve.
Vacuum-breaker inoperative.
Have qualified service technician clean or
replace vacuum breaker.
Violent waterline fluctuations
- surging.
OR
Water passing into steam
mains - priming.
Dirt, oil or other impurities in water.
Waterline too high.
Have qualified service technician skim
boiler.
Have qualified service technician adjust
waterline to normal height.
Incorrect piping.
Have qualified service technician pipe boiler
exactly as shown in Boiler Manual.
Sudden release of boiler steam
pressure by action of zone valves.
Have qualified service technician adjust
valve operating time or install slow-opening
valves.
Domestic water from tankless Mineral deposits insulate internal
Have qualified service technician delime or
replace coil.
heater is hot then suddenly
turns cold.
OR
Domestic water from tankless
heater is always lukewarm.
waterways of heater.
Boiler stop-leak compound has been
added to boiler water and is insulating
outside of coil.
Have qualified service technician remove
and clean coil AND drain and flush boiler to
remove stop-leak.
Incorrect mixing valve setting for
tankless heater.
Have qualified service technican adjust
mixing valve setting.
Domestic flow rate too high.
Have qualified service technician install flow
check valve set to rating of tankless heater.
Incorrect setting on tankless heater
control.
Have qualified service technician raise
tankless control setting. Adjust differential
on tankless control to lower setting.
The problems and corrections above represent common situations that can occur.
There may be others not listed above. It is important always to contact a qualified service techni-
cian if you have any questions about the operation of your boiler or system.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Annual Service Check List
The procedures and information on pages 8 through 11 are intended
only for a qualified service technician who has the necessary equipment to
inspect and adjust boiler and burner.A homeowner should never attempt
these procedures. Qualified service technician must read pages 2 and 3 before
proceeding.
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
D
A
T
E
Annual Service Call Check List
(follow in order listed below)
Comments
1
2
3
4
5
6
Check that boiler area is free from combustible
materials, gasoline and other flammable vapors
and liquids.
Check for and remove any obstruction to
combustion and ventilation air flow to boiler.
Check breeching and chimney or vent for
obstructions, damage, etc. Repair or replace as
necessary.
Clean boiler flueways. See page 9.
Perform service on low water cutoff, relief valve
and gauge glass. See page 11.
Check boiler and piping for leaks and repair if
found.
7
Inspect and adjust burner. See burner manual and:
- change nozzle.
- check ignition electrode settings.
- clean blower housing and wheel.
- make sure blower wheel turns freely.
- oil burner motor if required.
- clean air inlet.
- clean or change fuel filter and strainer.
8
9
Make sure boiler is filled to correct water level.
See page 10.
Start unit and verify combustion settings with
combustion test equipment.
See page 10.
10 Verify operation of all controls on boiler. See page
11.
Any parts of the boiler furnished byWeil-McLain must be replaced by parts listed in
Weil-McLain Boiler and Repair Parts Book.
8
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Detailed Service Procedures
Cleaning boiler flueways:
Make sure all electrical connec-
tions to boiler are turned off and wait until boiler
is warm, not hot, before cleaning. Failure to do so
will result in severe personal injury, death or
substantial property damage.
7. Once the flueways are cleaned, carefully
remove the paper from the floor of the
combustion chamber.
8. Verify sealing rope around flue area is intact.
Visually check condition and position of
insulation in combustion chamber floor,
and the refractories at the rear of boiler and
in the burner mounting door. Replace any
parts as necessary.
1. Topflueboilers-removebreechingandjacket
top panel.
Rear flue boilers - remove jacket top panel.
2. Remove flue collector hood, saving hardware
for reassembly.
9. Close burner mounting door and tighten nut
securely. Place flue collector hood on top of
boiler. Secure with hardware from step #2.
3. Shut off oil valves. Arrange drip pans under
the areas of oil piping that will be discon-
nected.
that
ly.
Disconnect oil line at burner so
you can swing open the door complete-
Maintain a gas-tight seal to
avoid possible flue gas leakage and carbon
monoxide emissions, which can lead to severe
personal injury or death.
4. Line combustion chamber floor with news-
paper to catch any soot that will be loosened
in the cleaning process.
5. Starting at the top of the boiler, use a wire
flue brush to thoroughly clean between all
pins at all angles. Be careful not to damage
side wall of rear refractory.
10. Check breeching for sooting and clean if
necessary. Install jacket top panel and
breeching.
11. Reconnect oil line and all electrical connec-
tions.
6. Move to the bottom of the flueways and clean
up between the sections to reach pins left
uncleaned in step #5.
Thoroughly clean flueways
between all pins at all angles.
Start on top of boiler,
finish from the bottom.
Cleaning Boiler Flueways
Figure 3
9
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Detailed Service Procedures
Fill the system:
1. Donotfill(exceptforleakagetests)untilboiler
is ready to be fired.
2. Fill to normal water line as indicated on jacket
front panel.
3. Boiler water pH 7.0 to 8.5 is recommended.
To place in operation:
Follow information below to prevent
severe personal injury, death or substantial prop-
erty damage:
●
Do not use crankcase drainings or any oil
containing gasoline. See burner manual for
proper fuel oil.
Donotattempttostartburnerwhenexcessoil
has accumulated in combustion chamber,
when unit is full of vapor, or when combustion
chamber is very hot.
Failure to maintain recom-
mended pH can cause section failure and
leaks.
●
Do not start burner unless collector hood, flue
●
cap, jacket cap, breeching and burner mount-
ing door are secured in place.
Never burn garbage or paper in the boiler.
Never leave combustible material around
boiler.
Skim steam boiler:
●
Clean new steam boilers to remove
any impurities. Failure to properly clean can
result in violent water level fluctuations, water
passing into steam mains, or high maintenence
costs on strainers, traps or vents. Skim boiler
only. Do not clean old piping or leaks can occur.
●
1. Verify boiler is filled with water to normal
waterline as indicated on jacket front panel.
2. Open burner door and verify rear target wall,
floor and burner door insulations are in
proper condition and position.
Do not use petroleum-based
compounds in boiler system. Damage to
system components can result, causing property
damage.
3. Verify burner mounting door is closed and
bolted tightly
and burner plug is connected.
4. Refer to burner manual for burner start-up,
adjustment and check-out procedures.
1. Provide 1-1/2" skim piping from skim tapping
(located on front of boiler) to floor drain. Add a
teeinpipingtoobserveskimwaterlevel.Raise
waterline to midpoint of skim tapping.
2. Fire burner to maintain water temperature
below steaming temperature during skimming
process.
3. Feed in water to maintain water level. Cycle
burner to prevent rise in steam pressure.
Continue skimming until discharge is clear.
4. While boiler is warm, but not hot, drain boiler
through drain valve.
Factory burner adjustment and settings may
not be suitable for specific job conditions.
Make final burner adjustments
using combustion test equipment to assure
proper operation. Do not fire boiler without
water. Sections will overheat, damaging boiler
and resulting in substantial property damage.
5. Check boiler and system piping for leaks.
6. Inspect breeching and venting for proper
operation.
5. Remove skim piping. Close drain valve. Fill
with fresh water to normal waterline. Start
burner and steam for 15 minutes to remove
dissolved gases. Stop burner.
6. Check traps and air vents for proper opera-
tion.
7. Process may need to be repeated after several
weeks of operation.
10
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Detailed Service Procedures
Controls requiring annual service:
FLOAT-TYPE LOW WATER CUTOFF:
GAUGE GLASS:
Follow instructions to blowdown cutoff on page 4.
Also refer to instructions from cutoff manufac-
turer in envelope assembly provided with boiler.
To clean glass:
1. Close lower gauge glass cock and carefully
open petcock below glass to blow water and
sediment out of glass by steam pressure.
2. Slowly open lower gauge glass cock and allow
a small amount of water to flush out through
the open petcock.
3. Closepetcockandfullyopenlowergaugecock.
The water level should immediately rise to its
proper level.
PROBE-TYPE LOW WATER CUTOFF:
Cutoff must be removed and inspected and
cleaned annually. Refer to cutoff manufacturer's
instructions in envelope assembly provided with
boiler.
4. If gauge glass breaks, close off both gauge
cocks and loosen glass retaining nuts to
STEAM RELIEF VALVE:
Check operation of steam relief valve. Follow
instructions on label fastened to relief valve.
remove gauge glass. Do not use thin glass
tubing as a replacement.
Scald potential. Do not check
operation of relief valve unless discharge piping
has been installed according to Boiler Manual.
If piping is not in place, a qualified service
technician must properly install piping.
General description of control operation:
LOW WATER CUTOFF:
GAUGE GLASS:
Shuts down boiler if there is a low water condi-
tion.
Indicates boiler water level. Cold fill water level
should correspond to line stamped on boiler
jacket. When boiler operates, water level will fluc-
tuate.
STEAM RELIEF VALVE:
PRESSURE GAUGE:
Provides discharge if boiler pressure exceeds 15
psig.
Provides reading of boiler pressure. Maximum
boiler pressure is 15 psig.
PRESSURE LIMIT CONTROL:
TANKLESS WATER HEATER:
If high steam pressure occurs, control shuts
down burners until pressure drops. Limit should
be set higher than design pressure of system. Op-
erating control can be set at 5 psig and
adjusted to comfort level. Normal operation is
usually less than 5 psig. At certain times the
system may operate under vacuum conditions.
Weil-McLain tankless heater ratings are based on
2000F boiler water temperature. To get rated out-
put, set tankless heater control to 2000F. Control
can be adjusted to meet system hot water require-
ments.
11
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 550-141-830/1202
Download from Www.Somanuals.com. All Manuals Search And Download.
|