INSTALLATION & OPERATION MANUAL
Roll Over Protective Structure (ROPS)
Model 98210001
Wright Manufacturing, Inc.
2-Post folding ROPS assembly and mounting hardware
IMPORTANT!
READ INSTRUCTIONS CAREFULLY BEFORE OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts list
ITEM
QTY PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
1
1
1
1
1
8
8
4
2
2
2
2
2
2
6
6
1
1
98210002 WZ ROPS LEG WELDMENT, LH
98210003 WZ ROPS LEG WELDMENT, RH
98210004 WZ ROPS CENTER WELDMENT
98210005 WZ ROPS HARDWARE KIT
98210006 WZ ROPS SEAT BELT RETRACTOR
98210007 WZ ROPS SEAT BELT BUCKLE
11990093 HHCS, 7/16-14NC x 1.25 LG GR 5
12990009 HEX NYLOCK NUT, 7/16-14NC GR 5
13990002 FLAT WASHER, 7/16
3-10131
HHCS, 1/2-13NC x 3.00 LG GR 5
98210008 WZ ROPS LOCKING PIN
98210009 WZ ROPS FOAM WASHER
3-10485
HEX NUT, CENTERLOCK, 1/2-13NC
98210010 WZ ROPS LANYARD RETAINER
98210011 WZ ROPS NYLON LANYARD
11990032 HHCS, 3/8-16NC x 1.25 LG GR 5
12990020 HEX NYLOCK NUT, 3/8-16NC GR 5
98210012 WZ ROPS MOUNTING INSTRUCTIONS
98210012 WZ ROPS BUMPER
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Preparation
1. Park machine on a level surface and set brake.
2. Remove ROPS and hardware from shipping box and identify all parts using
the parts list noted above.
Lower ROPS Leg Tube Installation
3. Jack and secure rear of mower and remove rear tires.
4. Remove left side rear fuel tank bracket bolts. Support tank.
5. Place LH leg weldment against LH machine frame mounting location.
6. Secure using (3) 7/16-14NC x 1.25” long hex head bolts, (3) 7/16-14NC
nylock hex nuts, (3) 3/8-16NC x 1.25” long hex head bolts and (3) 3/8-16NC
nylock hex nuts. Tighten bolts and nuts later in these instructions. See
Figure 1.
7. Loosen high pressure hoses at the pump and swivel away from LH leg
weldment.
Figure 1
8. Remove right side rear fuel tank bracket bolts. Support tank.
9. Repeat step 5-7 for installing RH leg weldment to RH side of machine frame
mounting location. See figure 2.
Figure 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper ROPS Hoop Installation
10.Install upper roll bar hoop assembly. Secure each side of hoop with (1)
½-13NC x 3.00” long hex head bolt, (1) pin retainer washer and (1) ½-13NC
center locking hex nut, into the upper mount hole of the hoop bracket.
Tighten only until the nut makes contact with the hoop bracket. Do not over
tighten. Hoop should pivot freely up and down. See Figure 3.
11.Install (1) EPDM washer onto each hitch pin. Position the top hoop into the
up-right position and insert hitch pins. See Figure 3.
Figure 3
12.Attach (1) nylon lanyard to the handle part of each hitch pin. Insert one end
of the lanyard through the retaining washer and attach to hitch pin spring
clip to the eye in the lanyard. Install the spring into the hitch pin. See
Figures 4, 5 and 6.
Figure 4
Figure 5
Figure 6
Download from Www.Somanuals.com. All Manuals Search And Download.
13.Torque 7/16” lower leg mounting hardware to 59 ft-lbs and 3/8” hardware to
37 ft lbs.
Seatbelt Installation
14. Secure retractable seat belt using (2) 7/16-14NC x 1.25” long hex head
bolts, (4)7/16” flat washers and (2) 7/16-14NC nylock hex nuts. See figures
7 and 8.
Figure 7
Figure 8
Wright Manufacturing, Inc.
4600X Wedgewood Boulevard
Frederick, MD 21703
Download from Www.Somanuals.com. All Manuals Search And Download.
|