Vanguard Managed Solutions
Vanguard 6500PLUS Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice (continued)
Proprietary Material
Information and software in this document are proprietary to Vanguard Managed Solutions
(or its Suppliers) and without the express prior permission of an officer of VanguardMS, may
not be copied, reproduced, disclosed to others, published, or used, in whole or in part, for any
purpose other than that for which it is being made available. Use of software described in this
document is subject to the terms and conditions of the VanguardMS Software License
Agreement.
This document is for information purposes only and is subject to change without notice.
Radio Frequency Interference Regulations
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Changes or modifications not expressly approved by VanguardMS could void the user's
authority to operate the equipment.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
This is a Class A product. Operation of this equipment in a residential environment may
cause radio interference, in which case the user may be required to take adequate measures to
correct the interference at his/her own expense.
You can obtain the proper cables from VanguardMS.
Writer: Bob Nichols
Publication Specialist: Denise Skinner
Illustrator: Tim Kinch
Part No. T0002, Rev C
Publication Code: KP
First Printing: April 1996
Manual is current for Release 5.2 of VanguardMS’sOperating Network Software.
To comment on this manual, please send e-mail to [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Software Features .........................................................................................
PLUS
Auxiliary Processor Cards .......................................................
1-10
1-15
PLUS
Token Ring Interface Module Option .....................................
2-32
2-68
PLUS
Processor with FLASH ..........................
Starting Up the Node ....................................................................................
Replacing DIMs .......................................................................................
Installing SIMMs .....................................................................................
DSU DIM Installation ..................................................................................
PLUS
for DSU Operation ........................................
Power-Up Verification ..................................................................................
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents (continued)
Enabling A Software Access Key ............................................................
2-80
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Overview
Introduction
This manual describes features, hardware, specifications, and applications for the
6500PLUS
.
Note
For information on operating system software and configuration, see the
Vanguard Basics Manual.
Audience
This manual is intended for operators of the 6500PLUS
.
How To Use This
Manual
The following table describes the contents of this manual.
This Chapter...
Chapter 1
Describes:
6500PLUS hardware and software features, and FCC
and telephone company procedures and requirements.
Chapter 2
Installing the hardware on the 6500PLUS, powerup and
verification, and installation of software options.
Appendix A
Appendix B
Cable pinouts for Ethernet and Token Ring.
Product specifications.
Downloading
Software
For operating software download procedures, refer to 6500PLUSDownloading
Procedures.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual (continued)
Special Notices
The following notices emphasize certain information in the manual. Each serves a
special purpose and is displayed in the format shown:
special purpose and is displayed in the format shown:
Note
Note is used to emphasize any significant information.
Caution
Caution provides you with information that, if not followed, can result in damage to
software, hardware, or data.
Mise en garde
Une mise en garde vous fournit des informations qui, si elles ne sont pas observées,
peuvent se traduire par des dommages pour le logiciel, le matériel ou les données.
Vorsicht
Ein Vorsichtshinweis macht Sie darauf aufmerksam, daß Nichtbefolgung zu
Software-, Hardware- oder Datenschäden führen kann.
Warning
Warning is the most serious notice, indicating that you can be physically hurt.
Avertissement
Un avertissement constitue le message le plus sérieux, indiquant que vous pouvez
subir des blessures corporelles.
Warnung
Eine Warnung ist der ernsthafteste Hinweis auf Körperverletzungsgefahr.
Software Revision This manual describes Release 5.2 of the Operating Network Software.
Level
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
About the 6500PLUS
Overview
Introduction
The 6500PLUS is a family of networking devices that can operate in private networks
or over public data networks. A 6500PLUS node can have from 6 to 54 ports, with
terminal port speeds of up to 38.4 kbps and network port speeds of up to 384 kbps.
About the 6500PLUS
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Features
Software Features
Introduction
You can configure, administer, and troubleshoot a 6500PLUS node from a local or
remote terminal acting as a control terminal. The terminal calls into the node's
Control Terminal Port (CTP), a software module that acts as the logical control
terminal port.
In addition, configurations can be saved and restored when a PC (with Kermit
protocol) is used as the local or remote control terminal.
Features and
Protocols
For a list of features and protocols supported by the 6500PLUSrefer to the Software
Release Notice that came with the operating software.
1-2
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Hardware
Introduction
A 6500PLUS node consists of at least one processor card, one or more optional
support cards, and, optionally, a TRIM card. A node can be contained in a standalone
enclosure, which can support only a processor card, or in a Modulus nest enclosure,
which can support one or more processor cards and several support cards.
Card Types
The 6500PLUS includes the following types of cards:
• 6500PLUS processor cards
• Auxiliary processor cards
• Asynchronous I/O (AIO) card
• Universal I/O (UIO) card
• Network storage option (NSO) card
• Token Ring Interface Module (TRIM) card
Processor Cards
The 6500PLUS processor cards provide the basic functions of a 6500PLUS node and can
be modified as required. The 6500PLUS processor cards are necessary to run 6500PLUS
Release 3.10 and greater software.
Support Cards
TRIM Card
The AIO, UIO, and NSO cards work with the processor cards to provide additional
ports and data storage.
The TRIM card provides access to Token Ring local area networks and supports
IBM/IEEE 802.5-compatible LANs.
The 6500PLUS does not have a dedicated control terminal port. Instead, any
asynchronous PAD port can become a control terminal port when an attached
terminal calls the node's control terminal facility and the proper password is entered.
For more details, refer to the Vanguard ONS Basics Protocols Manual (T0106).
About the 6500PLUS
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Enclosures and Backplanes
Introduction
The two types of enclosures for the 6500PLUS are:
• Standalone
• Modulus
Standalone
Enclosure
card. A standalone unit supports up to six X.25 or terminal ports depending on the
type of processor card installed.
Figure 1-1. 6500PLUS Standalone Enclosure
Modulus Enclosure The Modulus enclosure provides a 6500PLUS node with space for one or more
processor cards and several support cards, such as auxiliary processor cards, I/O
Figure 1-2. Modulus 21 Enclosure
1-4
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Supports Other
VanguardMS
Products
A Modulus enclosure contains plug-in card versions of VanguardMS products,
including Network Access Products, providing common housing and power to
multiple products. A single Modulus enclosure can include, for example, 35xx DSU/
CSUs, 326x dial modems, or 33xx leased-line modems in addition to 65xx nodes.
Types of Modulus There are four types of Modulus enclosures. The Modulus 8 and Modulus 18
Enclosures
enclosures are older models; the Modulus 9 and Modulus 21 enclosures are newer
models that are based on the Modulus 8/18 enclosures.
Modulus 8
Modulus 8 has 8 slots, holds four 6500PLUS product cards, and supports up to 24
ports. It is designed to be a desktop unit.
Modulus 18
Modulus 18 has 18 slots, holds eight 6500PLUS product cards, and supports up to 48
ports. It is designed to be installed in an industry-standard 19-inch rack.
Modulus 9
Modulus 9 has 9 slots, holds four 6500PLUS product cards, and supports up to 24
ports. It is designed as a desktop unit.
Modulus 21
Modulus 21 has 21 slots, holds nine 6500PLUS product cards, and supports up to 54
ports. It is designed to be installed in an industry-standard 19-inch rack.
Note
Two processor cards are needed to support 54 ports.
Backplanes
To accommodate the variety of products that you can install in Modulus enclosures,
VanguardMS has a line of product-specific backplanes to carry the signal and data
flow between the cards and the external environment and to provide cable
connections to the product card. Backplanes connect to the 6500PLUS cards on the
inside of the enclosure. Both the Modulus 8/18 and the Modulus 9/21 enclosures
have 25-pin DB25 connectors on the outside. (Older versions of Modulus 9/21
enclosures/backplanes have 26-pin DB26 connectors).
You can mount more than one backplane in a Modulus 8/18 and Modulus 9/21
enclosure to form independent nodes, but signals between backplanes cannot be
physically bridged. In other words, you cannot bridge two 24-port backplanes to
form a single backplane.
For general information on setting up Modulus 8/18 enclosures and inserting
6500PLUS cards into the enclosures, refer to the Modulus Planning and Installation
Guide (Product Code 80300). For Modulus 9/21 enclosures, see the Modulus 9 and
21 Installation and Operation Guide (Part No. 09564, Rev B).
About the 6500PLUS
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
PLUS
6500
Processor Cards
Introduction
The 6500PLUS processor card provides the main processing power in a 6500PLUS
node. There are three types of processor cards:
• 6505PLUS Asynchronous Access Server
• 6507PLUS Multifunctional Access Server
• 6525PLUS Network Concentrator
Description
6500PLUS processor cards are shipped with Single Inline Memory Modules (SIMMs)
in sockets U79 and U80. The processor card cannot operate without SIMMs.
Each processor card has six ports. You can password protect all ports on the
6505PLUSand 6507PLUS cards and all asynchronous ports on the 6525PLUS . You can
also configure processor cards from a locally or remotely connected terminal.
6505PLUS
Asynchronous
Access Server
The 6505PLUS is an asynchronous packet assembler/disassembler (PAD). If your node
is based on the 6505PLUS processor card, you can:
• Use only one 6505PLUS processor card in each node.
• Increase the maximum number of ports to 24 by adding up to three
asynchronous I/O (AIO) cards.
• Have only two network ports per node; these must be Ports 1 and 2 of the
processor card.
• Have a maximum number of 23 DTE ports per node.
Note
You can use UIO cards in 6505PLUS nodes if the UIO is configured only for PAD
ports.
6507PLUS
Multifunctional
Access Server
The 6507PLUS is a multifunction/multiprotocol packet assembler/disassembler
(PAD). If your node is based on the 6507PLUS processor card, you can:
• Have up to two 6507PLUS processor cards in each node.
• Have a maximum number of 24 ports per node (combination of processor
cards, AIO, or UIO cards).
• Have a maximum number of 4 network ports per node.
• Have a maximum number of 23 DTE ports per node.
• Optionally, configure ports to operate with network protocols (Frame Relay,
MX.25, XDLC), or with synchronous protocols (BSC 3270, BSC 2780,
SDLC). Any port can be configured as an asynchronous PAD port or to
operate with optional synchronous protocols.
1-6
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
6525PLUS Network
Concentrator
A 6525PLUS is a multifunction/multiprotocol packet assembler/disassembler (PAD)
and X.25 switch. If your node is based on the 6525, you can:
• Have up to nine 6525PLUS processor cards in a node.
• Have a maximum number of 54 ports per node (combination of processor
cards, AIO, or UIO cards).
• Have a maximum number of 54 network ports per node.
• Have a maximum number of 53 DTE ports per node.
• Configure any or all ports as X.25, MUX, or PAD ports because the 6525PLUS
allows switching on all six ports. Optionally, you can configure ports to
operate with synchronous protocols (SDLC, BSC2780/3270, and so on).
Port
Configurations
A 6500PLUS node contains only one type of processor card. For example, a single
node may include up to nine 6525PLUS processor cards, but it cannot contain a mix of
6525PLUS and 6507PLUS processor cards. The following table shows the port
configurations available for the different processor cards.
Card
Maximum Processor
Cards Per Node
Port
Type
Port Speed
Port
Number
6505PLUS
1
PAD
50 bps to 38.4 kbps
1200 bps to 80 kbps
1200 bps to 80 kbps
50 bps to 38.4 kbps
1200 bps to 80 kbps
1, 2, 3, 4, 5, 6
1, 2
MUX
X.25
PAD
1, 2
6507PLUS
2
9
1, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6
MUX
X.25
1200 bps to 128 kbps,
optionally to 384 kbps
1, 2, 3, 4, 5,
6*
6525PLUS
PAD
MUX
X.25
50 bps to 38.4 kbps
1200 bps to 80 kbps
1, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6
1200 bps to 128 kbps,
optionally to 384 kbps
1, 2, 3, 4, 5,
6*
*On 6507PLUS and 6525PLUS cards, Ports 3, 4, 5, and 6 have a maximum port speed of 80 kbps
if configured as X.25 ports.
About the 6500PLUS
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Processor Card
Figure 1-3 shows the front panel display for the processor card. From the front panel,
you can reset the card, test the lights, and monitor data transmissions by observing
the lights.
Physically, the processor cards are identical. The ID Module of each processor card
(located in socket U40) is unique and provides the functions specific to each type of
processor card.
STATUS (Green)
On: Software running.
POWER (Green)
On: Power on
Off: Power off
Off: Software not running (hardware fault).
Flashing: Software running and download
in progress.
6500
CPU PLUS
POWER
WATCHDOG (Red)
On: Processor failed to reset timer in
specified period, normally indicating
hardware or software failure.
(Press LAMP TEST to reset)
Off: Processor OK
STATUS
TEST (Red)
WATCHDOG
Indicates status and result of test
affecting any part of the node. Tests
can be locally or remotely initiated.
On: Test failed.
Off: Normal condition.
Flashing: Test in progress.
TEST
1
2
D
A
T
A
O
U
T
D
A
T
A
I
DATA IN (Yellow)
On: Data entering port = SPACE
Off: Data entering port = MARK
3
P
O
R
N
4
T
5
6
DATA OUT (Yellow)
On: Data leaving port = SPACE
Off: Data leaving port = MARK
RESET
Push button to initiate
hardware reset function.
RESET
LAMP TEST
When switch is pressed, all lights
on front panel come on.
LAMP TEST
WATCHDOG light, if latched ON
due to previous failure, is cleared
when switch is released.
CAUTION
REMOVE LAN I/O CABLE,
REAR FASTENERS AND
FRONT FILLERS BEFORE
REMOVING THIS CARD.
RI/TM
Set to RI position if port
is to emulate a dial modem;
otherwise, set to TM.
CTP > PT 6
1
When set to left, port 6 is configured as defined
in node configuration. When set to right and node
is booted, port 6 becomes a default-configured
asynchronous port that can be used to call the
control terminal port facility.
2
P
3
R
I
T
M
O
R
T
4
5
6
DIAG
Specifies how internal hardware
diagnostics will be implemented
when the node is powered on or reset.
Left: Diagnostics will run once.
CTP
PT.6
DIAG.
DFLT NODE
DFLT NODE
P.C. 68700
LAN
COMPATIBLE
To reset all configurable parameters to default
value, press RESET, set this switch to the right,
and press RESET again.
Right: Diagnostics will run 10 times.
Figure 1-3. 6500PLUS Processor Card Front Panel
1-8
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Optional FLASH
Module
Optionally, a FLASH memory module can be attached to a processor card to provide
software distribution and software download capabilities. This optional daughtercard
contains up to 3 Mbytes of nonvolatile FLASH memory and is used for remote
software distribution and software download.
About the 6500PLUS
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
6500PLUS Auxiliary Processor Cards
Introduction
6500PLUS auxiliary processor cards increase throughput for 6507PLUS and 6525PLUS
nodes. They provide additional processing power, as well as six additional ports.
Description
A 6500PLUS auxiliary processor card is a 6507PLUS or 6525PLUS processor card without
a FLASH module, meaning that the card lacks software storage capabilities.
Optionally, you can purchase a FLASH module for a 6500PLUS auxiliary processor
card for downloading software. The front panel is the same as the front panel of the
Note
You cannot use a 6500PLUS auxiliary processor card as the primary processor
card in a node and cannot install it in the lowest-numbered slot in the node.
The 6500PLUS auxiliary processor card is intended to be used for redundancy and
to increase node performance.
1-10
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
PLUS
6500
Asynchronous and Universal I/O Cards
Introduction
Two types of I/O cards are:
• Asynchronous I/O (AIO)
• Universal I/O (UIO)
AIO Card
UIO Card
You can use an AIO card with all 6500PLUS processor cards. It provides six
asynchronous ports that can be configured as PAD ports. This card supports PAD
port speeds from 50 to 19200 bps and split speed operation (75 bps inbound and
1200 bps outbound) on all ports.
You can use a UIO card with 6507PLUS and 6525PLUS cards. The UIO card provides
six asynchronous or synchronous ports. You can configure ports as X.25, MUX, or
PAD ports. Optionally, you can configure them to operate with synchronous access
protocols (SDLC, BSC3270, BSC2780/3780, and so on). This card supports PAD
port speeds from 50 to 19200 bps, and synchronous speeds from 1200 bps to 80
kbps.
Note
You can use UIO cards with 6505PLUS processors if you configure them only for
PAD ports.
Description
The following table describes the characteristics of each card.
Card Type
AIO
Works with...
• 6505PLUS
• 6507PLUS
• 6525PLUS
• 6507PLUS
• 6525PLUS
Port Types
Split Speed
Yes
PAD
UIO
• PAD
• MUX
• X.25
• optional
synchronous
protocols
No
• 6505PLUS, if PAD
ports only
About the 6500PLUS
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Front Panel Display Figure 1-4 shows the front panel display, which is the same for both types of I/O
cards.
.
6500
I/0
TEST (Red)
Indicates status and result of
test affecting any part of node. Tests
can be locally or remotely initiated.
On: Test failed
Off: Normal condition
Flashing: Test in progress
TEST
1
2
D
A
T
A
O
U
T
D
A
T
A
I
DATA IN (Yellow)
On: Data entering port = SPACE
Off: Data entering port = MARK
3
4
P
O
R
T
N
5
6
DATA OUT (Yellow)
On: Data leaving port = SPACE
Off: Data leaving port = MARK
RI/TM
Set to RI position if port
is to emulate a dial modem;
otherwise, set to TM.
1
2
3
4
5
6
P
O
R
T
R
I
T
M
P.C. 68904
PLUS
Figure 1-4. 6500
Panel
Universal I/O or Asynchronous I/O Card Front
1-12
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
PLUS
6500
Network Storage Option Card
Introduction
The 6500PLUS network storage option (NSO) card expands basic node memory for
support of large packet sizes.
NSO Card
Description
The NSO card has a 3.5-inch high-density floppy disk drive with a storage capacity
of 1.4 Mbytes (MS-DOS–formatted disks). The disk drive is used to download new
and optional software to the node. The card contains 1 Mbyte of DRAM, which can
be increased in 2-Mbyte increments to 5 Mbytes by inserting SIMMs.
The MEM lights on the front panel indicate the amount of NSO RAM used by the
system. A node with a lot of memory in the processor card may not use all the
memory in the NSO card. In this case, only some of the lights on the NSO card may
come on.
About the 6500PLUS
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
NSO Card
Figure 1-5 shows the NSO card.
TEST (Red)
Indicates status of internal tests.
On: Test failed
6500
NSO
Off: Normal condition
Flashing: Test in progress
TEST
MEM1
MEM3
MEM5
MEM (Yellow)
Indicates amount of memory
available on this card
MEM 1: 1 Mbyte RAM
MEM 3: 3 Mbyte RAM
MEM 5: 5 Mbyte RAM
DISK
On when disk is being accessed.
P.C. 68908
PLUS
Figure 1-5. 6500
Network Storage Option Card
1-14
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
6500PLUS Token Ring Interface Module Option
Introduction
The Token Ring Interface Module (TRIM) card is an option card that lets you route
LAN traffic through your network.
Features
The TRIM card provides the following features:
• VanguardMS Periphery Routing
• One Token Ring LAN port operating over Shielded Twisted Pair (STP) or
Unshielded Twisted Pair (UTP) cable at 16 or 4 Mbps
• IBM-compatible Source Route Bridging support
• Support for up to 32 remote LAN bridge connections
• Capability for Frame Relay, X.25, MX.25, and/or XDLC network connections
for Token Ring LAN traffic
Description
You can mount the TRIM card on 6507PLUS or 6525PLUS processor cards (not
6505PLUS cards) within a Modulus enclosure. The TRIM card is suitable only in a
Modulus enclosure. A single node can support just one TRIM card. Modulus 8 and
Modulus 9 enclosures can support one node containing a TRIM card. Modulus 18
and Modulus 21 enclosures can support a maximum of three nodes containing
TRIM cards.
The TRIM card provides one LAN port through its backplane; connection can be
made through either the unshielded twisted pair (UTP) or the shielded twisted pair
(STP) LAN connectors. All LAN configuration is performed through Control
Terminal Port (CTP) menus. See the Vanguard ONS Basics Protocols Manual
(T0106) for configuration information.
A PROM chip on the TRIM card provides the BIA (Burned In Address), the LAN
MAC address unique to that port. The BIA is the default value for the Port TMAC
Address (found in the Port configuration record).
TRIM Card
Figure 1-6 shows how the TRIM card is mounted on the processor card.
TRIM Card
Bottom of Card
Processor Plus Board
(Solder Side)
Figure 1-6. Token Ring Interface Module (TRIM) Card
About the 6500PLUS
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
TRIM-Compatible
Processor Card
Upgrade
Not all 6500PLUS processor cards can support the TRIM card. A TRIM-compatible
processor card has a “LAN COMPATIBLE” marking on the lower front panel
VanguardMS Sales representative to order a LAN-capable processor card.
1-16
About the 6500PLUS
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
6500PLUS Integral DSU
Introduction
The 6500PLUS Integral DSU option is intended for use in installations
requiring connection to a DDS interface, conforming to AT&T 62310 or ANSI
T1E1.4/91-006, and running at a rate of 56 kbps. At present, this optional DSU
interface is only available with VanguardMS 6500PLUS enclosures using a 25-pin D
connector interface.
The DSU option normally uses clocking derived from the network interface, but may
also be configured to originate the clocking, thus providing the standard DSU and
CSU loopbacks. Installation of the DSU option requires a hardware and software
upgrade to the base 6500PLUS product.
Hardware
Components
The DSU option consists of two hardware modules, the Data Interface Module
(DIM) and the External Interface Module (EIM).
DIM
EIM
The DSU DIM is a small (approximately 1 in. x 3.5 in.) circuit card installed as a
daughtercard onto the 6500PLUS processor card. The DIM module provides the
proper power to the EIM and also performs the data translation functions.
option.The EIM has an 18 in. cable with a 25-pin connection for interface with the
6500PLUS unit, and an RJ-48S jack for connection to the DDS line.
18-inch Cable
RJ-48S Jack
DB25 Connector
Figure 1-7. External Interface Module (EIM)
DSU Interface
The DIM and EIM modules work cooperatively to provide a DSU interface and must
be installed together for proper operation. These devices are only intended for use
with VanguardMS 6500PLUS equipment.
About the 6500PLUS
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Installation
Overview
Introduction
This chapter contains installation procedures for:
• 6500PLUS Series standalone enclosures
• 6500PLUS processor card components
• Software options
A description of the processor front panel LED power-up sequence and soft-
ware upgrade procedures are also included.
This chapter also contains instructions for installing TRIM cards in Modulus
enclosures. For general information on setting up Modulus 8/18 enclosures and
inserting 6500PLUS cards into the enclosures, refer to the Modulus Planning and
Installation Guide . For Modulus 9/21 enclosures, see the Modulus 9 and 21
Installation and Operation Guide.
Warning etc.
The following special notices apply to all equipment handling procedures in this
chapter:
Be sure a power outlet is near the equipment and easily accessible.
Warning
Only trained, qualified technicians should perform the installation and replacement
procedures in this chapter.
Caution
Ports that are capable of connecting to other apparatus are defined as SELV. To
ensure conformity with EN60950 — ensure that these ports are only connected to
ports of the same type on other apparatus.
6500PLUS cards, DIMs, SIMMs, and FLASH modules are sensitive to static
discharge, which can damage components. Use proper handling and grounding
precautions whenever you handle a 6500PLUS card.
Installation
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Installing Standalone Units
Introduction
Unpacking
This section explains how to set up a 6500PLUS standalone enclosure. When you
receive the enclosure, it already contains a 6505PLUS, 6507PLUS, or 6525PLUS card.
Before you unpack the 6500 standalone enclosure, check the outside of the package.
If the package is damaged, contact the shipping agent.
Site Preparation
Install the standalone enclosure in a clean location free from shock, vibration, and
extremes of temperature and humidity. The site must meet the physical and
least 12 inches (30.5 cm) clearance at the rear of the unit for interface cabling and
ventilation.
Caution
Be sure that the standalone enclosure's air vents are uncovered. If the vents are
covered, the unit could overheat.
Example of
Standalone
Enclosure
Figure 2-1 shows a standalone enclosure.
Power Supply
Backplane
Processor Card with
6505, 6507, or
6525 ID Module
Screw
Clear Plastic Insulator
Door
Figure 2-1. Standalone Enclosure
2-20
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Installation
Procedure
The standalone enclosure already contains a 6505PLUS, 6507PLUS, or 6525PLUS card.
To install the unit, follow these steps:
Step
Action
Description/Result
1
Place the unit at its designated site The power cord is attached to the
and plug the power cord into a
suitable primary power source.
2
Switch on the power, located at the The front panel lights turn on
rear of the unit.
as described in the “Power-Up
After a few minutes, the green
STATUS light comes on to indicate
the node is ready to process calls.
If this does not occur, call your
VanguardMS representative.
3
4
Configure the unit through the
Control Terminal Port (CTP)
menus.
To access the CTP, attach a
terminal to Port 6 with an EIA
232-D connector. Port 6’s default
settings are standard terminal port
values: 9600 baud, 8 data bits, 1
stop bit, no parity.
When the (*) prompt appears on
the terminal, type the following:
This is the default password value.
The Main menu appears. See the
Vanguard ONS Basics Protocols
Manual (T0106) for configuration
information.
.ctp <CR>
At the password prompt, press
<CR>
Rear View
Figure 2-2 shows the rear view of the standalone enclosure.
..
PORT 6
PORT 3
PORT 5
PORT 2
PORT 4
PORT 1
Figure 2-2. Rear View of Standalone Enclosure
Installation
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Replacing Processor Cards in Standalone Enclosures
Introduction
This section describes how to replace a 6500PLUS processor card in a standalone
enclosure.
Warning
Before opening the enclosure, be sure that it is unplugged from the power source.
Caution
6500PLUS cards and their components are sensitive to static discharge, which can
damage components. Use proper handling and grounding precautions, including the
use of an anti-static grounding strap, whenever you handle a card.
Card Removal
Procedure
To remove a processor card, follow these steps:
Step
Action
1
Open the front door of the enclosure and remove it by pressing down
2
locate the six locking tab slots (three on each side). There are four
locking clips (two in the front and two in the back) in the slots.
3
4
5
6
Using a small pair of pliers, remove the four locking clips from the
slots.
Using a small screwdriver or similar tool, press the locking tabs
On the rear panel above the power cable, loosen, but do not remove,
the locknut and washer.
Turn the enclosure over so it is upright. Tilt the cover clockwise
(when viewed from the rear) until you encounter resistance
(Figure 2-3).There is a cable connecting the power supply and the
backplane.
7
Reach into the enclosure and disconnect the power cable from the
backplane socket.
8
9
Remove the cover.
Using a screwdriver, remove the screw holding the card to the bottom
of the enclosure (Figure 2-6).
10
Lift the card and backplane out of the enclosure and carefully remove
the backplane from the card.
2-22
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Door Removal
Figure 2-3 shows how to remove the door on the standalone enclosure.
Front Door
To remove door, separate mounting
tabs from base and remove.
Figure 2-3. Remove the Standalone Enclosure Door
Installation
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Locking Tabs
Figure 2-5 shows how to release the tabs.
Figure 2-5. Using Screwdriver on Locking Tabs
Installation
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Retaining Screws
Figure 2-6 shows the retaining screws on the processor card.
Backplane
Front Spacer Panel
Retaining Screw
PLUS
6500
Processor Card
Standalone Base
Figure 2-6. 6500PLUS Processor Card with Retaining Screw
Procedure to Add a Follow these steps to add a processor card to the standalone enclosure:
Replacement Card
Step
Action
1
Carefully insert the replacement card into the backplane's connector.
Be sure that the clear plastic insulator is in place, under the card.
When pressing the replacement card into the backplane connector,
use direct force. Wiggling the card may damage it.
The card's tabs and the backplane's connector are keyed, so you
cannot insert the card incorrectly.
2
3
From the old card, remove the spacer panel attached to the front
Place the backplane and card into the bottom of the enclosure. Be
sure that the backplane and the card mounting hole are properly
aligned.
4
Secure the card to the enclosure using the retaining screw that held
the card to the bottom of the enclosure.
2-26
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Standalone Units
Step
Action
5
Take the enclosure cover and connect the power cable to the
backplane connector. Be sure to align the keyed pin on the cable to
the connector.
6
Align the enclosure cover and bottom, and press the two gently
together.
This requires alignment of the backplane and the locking tabs. Be
sure that the cables are not pinched between the enclosure and metal
parts. When all elements are correctly aligned, the locking tabs snap
into place.
7
8
9
Tighten the locknut and washer on the rear panel.
Insert the four locking clips into the slots.
Reinstall the door by gently pressing the hinge parts together.
After the card has been properly installed, reconnect the cables and
turn on the unit.
Installation
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installing Nodes in Modulus Enclosures
Introduction
Installing 6500PLUS cards into Modulus enclosures is the same as installing any other
type of Modulus product card.
Additional
Information
For general information on setting up Modulus 8/18 enclosures, attaching product
backplanes, inserting cards, and attaching front and rear filler panels to the
enclosures, refer to the Modulus Planning and Installation Guide . For general
information about Modulus 9/21 enclosures, see the Modulus 9 and 21 Installation
and Operation Guide.
The following sections contain Modulus information specific to 6500PLUS products,
including multi-processor node information, TRIM card installation, and grounding
strap installation.
2-28
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Multiprocessor Nodes
Introduction
A node based on the 6507PLUS or the 6525PLUS processor card can contain more than
one processor card to improve reliability and availability. The two processor cards
provide backup support to each other.
Multiprocessor
Node Example
Figure 2-7 shows a multiprocessor node where an enclosure is configured for two
6507PLUS or two 6525PLUS cards.
Slot 2
Processor 2
Slot 1
Processor 1
Slot 3
Universal I/O 1
Slot 4
Universal I/O 2
Slot 5
Async I/O
Figure 2-7. Multiprocessor Node
Operation
This is how a multiprocessor node operates under normal conditions, with both
processors working.
• Processor 1 handles the I/O interrupts from its own six on-board ports.
The processor card in the lowest-numbered slot is the master. In Figure 2-7,
Processor 1 is the master processor.
• Processor 2 handles its own on-board interrupts plus those from universal I/O
cards 1 and 2 and the asynchronous I/O card.
• If Processor 2 fails, the node restarts and Processor 2 is disabled. When a
processor card is disabled, interrupt requests generated by cards to the right
pass to the processor card on its left. While overall throughput is reduced,
links to the right of the failed processor are restored automatically.
Installation
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Replacing Master Processor of Multi-Processor Node
Introduction
This section describes how to replace a failed master processor in a multiprocessor
node without losing your configuration.
Keeping the
Original Node
Configuration
All processor cards in a node contain identical copies of CMEM. If the master
processor fails, you can keep the original node configuration and options if you:
• Replace the master processor with another processor card from the node
(preserving the configuration).
• Keep the ID Module of the original master, retaining the original SAKs for
the options you purchased.
Replacement of
Other Processor
Cards
To replace a processor card other than the master, remove the old processor card and
insert the new one. Be sure you use the correct type of ID Module (for example,
6505, 6507, or 6525). You do not have to change the configuration. When the node
starts up, the CMEM on the new processor card is loaded automatically with the
node configuration.
Note
All processor cards in a multiprocessor configuration must operate on the same
revision of software. If they do not have the same software revision, remove the
software from the failed processor card and exchange it with the software on the
spare card. All processor cards in a multiprocessor configuration must use the
same type of ID Modules—the node must be composed entirely of one type of
processor card (6505, or 6507, or 6525 cards).
Replace the Master Follow these steps to replace the master processor:
Processor
Caution
This procedure saves your configuration. If you do not use this procedure to replace
the master processor card, the default configuration is transferred to the other
processor cards in the node and you must reenter or download your configuration.
Step
Action
Result/Description
1
Remove the failed processor
card from the lowest-
numbered slot in the node.
2
the CMEM chip between the
failed master processor card
and the new processor card.
instructions. Return the failed card to
your VanguardMS Service representa-
tive.
3
4
Install the new processor card This will now be the master processor.
into the lowest-numbered slot.
Boot the node.
2-30
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installation
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Adding a Secondary 6500PLUS Processor with FLASH
Introduction
When adding another 6500PLUS processor card to a node, be sure that all processor
cards are running the same software revision. 6500PLUS processor cards redistributed
within a network may contain different revisions of software.
When To Add
Two situations in which you may add an additional 6500PLUS processor card with
Another Processor FLASH memory to a node are when you want to:
with FLASH
• Maintain the current software revision
• Upgrade with software from the new 6500PLUS processor card
In both cases, the FLASH Enable Option is required.
These situations apply to the 6507PLUS and 6525PLUS nodes. A 6505PLUS node does
not support multiple processor cards.
Before You Begin
Follow these steps to access the control terminal port:
Step
Action
Result/Description
1
Connect a terminal to a local PAD
port, and enter the following at the
(*) prompt:
.ctp <CR>
2
Enter the password when you are
prompted.
The default password is <CR>.
After you enter the password, the
Main menu appears.
For more information about
accessing the CTP, see the
Vanguard ONS Basics Protocols
Manual (T0106).
2-32
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Maintaining the
Current Software
Revision
Follow these steps to add a processor card with FLASH memory to your node and
download the current software revision to the new processor’s FLASH memory:
Step
Action
1
At the control terminal port, use the Node Statistics to confirm that the
node is running software from RAM and that FLASH is enabled.
If FLASH is disabled, enable FLASH by doing the following:
a) Select FLASH Memory from the Main menu
b) Select Enable FLASH.
2
3
Install the new processor card in any slot on the node to the right of the
master processor.
At the control terminal:
a) Select FLASH Memory from the Main menu.
b) Select Copy Software to FLASH.
It may take several minutes to load the software
4
After the software has been written to the FLASH, check the Node
Statistics to see that all FLASH cards in the node contain the same
revision of software.
Software
Distribution
Generally, software distribution is managed from a central site. The Network
Manager configures and initiates software updates as required.
When Software is
Unavailable
You can upgrade with software from the new processor card when the software is
unavailable elsewhere in the network by:
•
Adding a secondary processor with FLASH memory to your node
• Making the software in the new processor’s FLASH the operating revision of
software in the node
• Retaining the node’s configuration and options
Installation
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Upgrading with
Follow these steps to ensure that the node’s configuration is not lost. If you do not
Software From the follow this procedure, CMEM will be overwritten.
New Processor
Card
Step
Action
1
At the control terminal, use the Node Statistics to confirm that the node
is running software from RAM and that FLASH is enabled.
If FLASH is disabled, enable FLASH by doing the following:
a) Select FLASH Memory from the Main menu
b) Select Enable FLASH.
2
3
Remove the master 6500PLUS processor card (in lowest-numbered slot).
Exchange the ID Module and CMEM chips between the master
6500PLUS processor card and the new 6500PLUS processor card.
the CMEM Chip” section on page 2-65 for instructions.
4
5
Install the new 6500PLUS processor card in the lowest-numbered slot
and install the former master processor card in the slot to the right.
At the control terminal, use the Node Statistics to confirm that the node
is running the new software.
If the new software is not running, the FLASH memory may not have
been enabled on the new processor card. Enable the FLASH memory
and cold boot the node to force loading from FLASH memory.
6
At the control terminal:
a) Select FLASH Memory from the Main menu.
b) Select Copy Software to FLASH.
2-34
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installing/Replacing Processor Cards
Introduction
You can insert and remove any 6500PLUS processor card from a powered-up Modulus
nest without damage.
Caution
6500PLUS cards and their components are sensitive to static discharge, which can
damage components. Use proper handling and grounding precautions, including the
use of an anti-static grounding strap, whenever you handle a card.
Replacement
Procedure
After inserting or removing a card, press the Reset button on the 6500PLUS processor
card to restart the node. Reboot the node.
Replacing a Card in When replacing a card in a Modulus 8/18 enclosure, refer to the Modulus Planning
a Modulus 8/18
Enclosure
and Installation Guide. When replacing a card in a Modulus 9/21 enclosure, refer to
the Modulus 9 and 21 Installation and Operation Guide.
Installation
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Requirements for Installing a TRIM Card
Introduction
This section describes the requirements for installing a TRIM card. TRIM cards are
suitable only in a Modulus enclosure and only with 6507PLUS and 6525PLUS cards.
A 6500PLUS node can support only one TRIM card. Modulus 8 and Modulus 9
enclosures can support just one node containing a TRIM card. Modulus 18 and 21
enclosures can support up to three nodes containing TRIM cards.
TRIM Card Upgrade The following product codes allow you to upgrade your system for LAN
Kits compatibility:
Product
Code
Product
Description
68517
68505
68506
LAN Bridging Software Authorization Key Accesses the LAN bridging software.
(SAK)
TRIM Card
Provides just the Token Ring Interface
Module card.
6500PLUS LAN compatible processor card
upgrade.
Provides a LAN compatible 6500PLUS
processor card with TRIM card already
attached.
68507
Modulus 9/21 12-port TRIM Package
Includes a TRIM card, a Modulus 9/21 12-
port backplane, and front and rear filler pan-
els.
68514
68516
Modulus 18 RFI Suppression Screen
6500PLUS TRIM Installation Kit for Modulus Provides the front and rear filler panels
9/21 Enclosures
Required for Modulus 18 installations.
needed when you install a TRIM card into
the Modulus 9/21 nest.
68518
68520
6500PLUS TRIM Installation Kit for Modulus Provides the front and rear filler panels used
8/18 Enclosures
when installing a TRIM card into the
Modulus 8/18 nest.
Modulus 21 RFI Suppression Bar
Required for Modulus 21 installations.
TRIM-Compatible
Processor Card
Not all 6500PLUS processor cards can support the TRIM card. A processor card that
supports a TRIM card has a “LAN COMPATIBLE” label on the lower front panel.
TRIM cards can be physically mounted on all 6500PLUS processor cards, but work
only with cards marked “LAN COMPATIBLE.” If your processor card does not
have this marking, see your VanguardMS sales representative to order a LAN-
capable processor card.
In multiple-CPU configurations, only the processor card supporting the TRIM card
needs to be LAN-compatible.
2-36
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Modulus 8/18 Nests The TRIM card has its own backplane and attaches to the solder side of the 6500PLUS
processor card. The TRIM card requires two Modulus slots. The TRIM filler panel
for Modulus 8/18 nests is two slots wide as shown in Figure 2-8.
65xx 18-Port Backplane
Rear View
Attach backplane using a
Phillips-head screwdriver.
Shielded
Twisted Pair
Unshielded
Twisted Pair
TRIM Card
Filler Panel for
Modulus 8/18
Use flat-head
screwdriver to
attach captive
hardware.
Figure 2-8. TRIM Card Rear Filler Panel for Modulus 8/18 Enclosures
Installation
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Guidelines for
Installing a TRIM
Card in a Modulus
8/18
Consider the following if you install a TRIM card in a Modulus 8/18 enclosure:
Note
Before you add a TRIM card to an existing node, be sure the enclosure has room
for it as described above. To make space, you may need to rearrange cards and
backplanes, which requires a node shutdown first.
• A processor card with attached TRIM card requires four slots — two slots for
the TRIM card and two for the processor card.
• You can attach a TRIM card only to the processor card in the
lowest-numbered slot of a backplane (this is the master processor
in a multi-processor node).
• There must be two empty slots beside the backplane next to the
lowest-numbered processor card.
• The TRIM card rear filler panel covers the back of the two slots taken by the
TRIM card. This rear panel, which has a cutout for the LAN port connectors,
• When installing in a Modulus 18 enclosure, a metal screen must be installed
onto the Modulus 18 door to meet FCC requirements. See the “Preparing
2-38
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Modulus 18
Figure 2-9 shows the TRIM card spacing in a Modulus 18 enclosure.
6500 Node 18-Port Backplane
TRIM Card Filler Panel
Modulus 18-Slot Nest
Top View
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
Slots
PLUS
Note: 6500
installed in left-
most position in Modulus
18. The TRIM card requires
two slots for its backplane.
TRIM
Card
Front
Processor Card
Modulus 8/18
Filler Panels
6500 Node 18-Port Backplane
TRIM Card Filler Panel
Slots
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
PLUS
Note: 6500
installed to the
left or right of a product
backplane in Modulus 18.
The TRIM card requires
two slots for its backplane.
TRIM
Card
Front
Processor Card
Modulus 8/18 Filler Panel
Figure 2-9. TRIM Card Spacing in a Modulus 18 Enclosure
Installation
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Modulus 9/21 Nests The TRIM card has its own backplane and attaches to the solder side of the 6500PLUS
processor card. The TRIM card requires two Modulus slots. The TRIM filler panel
for Modulus 9/21 nests is one slot wide as shown in Figure 2-10.
Modulus 9 Rear View
TRIM Card
Filler Panel for
Modulus 9/21
Shielded
Twisted Pair
65xx
18-Port
Backplane
Unshielded
Twisted Pair
TRIM Card
Filler Panel for
Modulus 8/18
Use flat-head
screwdriver to
attach captive
hardware.
Figure 2-10. TRIM Card Rear Filler Panel for Modulus 9/21 Enclosures
Guidelines for
Consider the following if you install a TRIM card in a Modulus 9/21 enclosure:
Installing a TRIM
Card in a Modulus
9/21 Enclosure
Note
Before you add a TRIM card to an existing node, be sure the enclosure has room
for it as described above. To make space, you may need to rearrange cards and
backplanes, which requires a node shutdown first.
• A processor card with attached TRIM card requires four slots — two slots
each for the TRIM card and the processor card.
• The TRIM card attaches only to the processor card in the lowest-numbered
slot of a backplane (this is the master processor in a multi-processor node).
• When installing in a Modulus 21, install a horizontal bar on the front door to
meet FCC requirements.
2-40
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
• To install a node with a TRIM card in the left-most position of a nest, attach
the backplane at Slot 3 of the nest. Insert the TRIM/processor card into Slot 3.
The TRIM card takes up Slot 2 and Slot 1 (the width of the card does not
permit it to be installed in Slot 1). The TRIM card rear filler panel, which has
cutouts for the LAN port connectors, covers the backplane in Slot 2; a stan-
dard Modulus 9/21 rear filler panel covers the back of Slot 1. Two standard
Modulus 9/21 front filler panels cover Slots 1 and 2 at the front of the nest.
• If there is a product in the nest, such as a modem, that consists of a one-slot
wide product card plugged into a two slot-wide backplane, then one slot can
be saved when installing a TRIM. The modem product should be installed to
the left of the TRIM card.
• To install a node with a TRIM card next to another product backplane,
leave one slot empty between backplanes. Modulus 9/21 product backplanes
take one slot in addition to what their product cards take. For example, a 54-
port backplane takes up 19 slots, although its nine cards take up 18 slots (two
slots per card). The TRIM backplane fills the one slot between the two
backplanes. The TRIM card itself fills the one slot gap and one slot from the
adjacent backplane. Two standard Modulus 9/21 front filler panels cover the
works only if a one-slot card is installed to the left of the node.
Installation
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Most Position
enclosure.
Modulus 21-Slot Nest
Top View
Modulus 9/21 TRIM Card Filler Panel
6500 Node 54-Port Backplane
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21
Slots
Modulus 9/21
Filler Panel
TRIM
Card
Front of Nest
Modulus 9/21 Filler Panels
Processor Card
Note: TRIM card installed in left-most position in Modulus 21.
The TRIM card requires two slots for its backplane.
Figure 2-11. TRIM Card In Left-most Position of Modulus 21 Enclosure
2-42
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
TRIM Card
Figure 2-12 shows A TRIM card between two backplanes in Modulus 21.
Between Two
Backplanes
Modulus 21-Slot Nest
Top View
9/21Trim Card Filler Panel
6500 Node 54-Port Backplane
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21
Slots
3360 Modem
Backplane
3360 Modem
Card
TRIM
Card
3360 Modem
Front Panel
Front
Modulus 9/21 Filler Panels
Figure 2-12. TRIM Card Between Two Backplanes In Modulus 21
Backplane Support The following table lists the backplanes capable of supporting TRIM cards. Modulus
for TRIM Cards
18 and 21 enclosures support a maximum of three TRIM cards, but the actual
number of nodes with TRIM cards depends on the sizes of the enclosures and
backplanes you choose.
Enclosure
Modulus 8
6507PLUS
6525PLUS
6-,12-, and 18-port backplanes
6-,12-, and 18-port backplanes
Modulus 18 6-,12-,18-, and 24-port backplanes
6-,12-,18-, 24-, 36- and 48-port
backplanes
Modulus 9
12- and 18-port backplanes
12- and 18-port backplanes
Modulus 21 12-,18-, and 24-port backplanes
12-,18-, 24-, 36-, and 54-port
backplanes
Installation
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
2-44
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installing and Connecting a TRIM Card
Introduction
This section describes how to install a TRIM card in a 6500PLUS node.
Caution
6500PLUS cards and their components are sensitive to static discharge, which can
damage components. Use proper handling and grounding precautions, including the
use of an anti-static grounding strap, whenever you handle a card.
Steps for Installing To install a TRIM card, perform the following steps:
a TRIM Card
1) Attach the TRIM card if it is not already attached when it arrives from the
factory.
2) Install the processor card into the modulus nest.
3) Connect the LAN cables.
Note
In multiple-CPU configurations, only the processor card supporting the TRIM
card needs to be LAN-compatible.
Attaching a TRIM
Card
Depending on the product code you have ordered, your TRIM card may arrive
already attached to the processor card. If this is the case, skip to the next section,
Step
Action
1
2
Follow the Modulus space considerations described in previous sections.
Attach the TRIM rear filler panel to the enclosure.
• If you are installing the TRIM card in a Modulus 8/18 enclosure,
use a Phillips-head screwdriver to attach the TRIM rear filler
panel to the backplane with the four screws provided
• If you are installing the TRIM card in a Modulus 9/21 enclosure,
use a flat-head screwdriver to attach the captive screws on the top
Attach a standard Modulus rear filler panels as needed.
3
4
Attach the header pins to the TRIM card. Insert the header pins in the
socket so that the four pins without ferrite beads face the top of the
The pins should seat firmly into the socket; do not bend them.
Turn the 6500PLUS processor card so that its solder side faces upward.
Insert the header pins into the socket on the processor card, being careful
Be sure to support both the TRIM and processor cards while pressing
them together to avoid bending and thereby possibly damaging the
processor card.
5
On the component side of the processor card, screw the four fastener
Installation
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installing and
Connecting a TRIM
Card
Follow these steps to install and connect the TRIM card:
Step
Action
1
Insert the 6500PLUS processor/TRIM card combination into the lowest-
numbered slot of the node backplane.
You can insert the processor/TRIM card combination in a powered-on
nest. However, power to other cards in the nest may be disturbed
because of the inrush of current to the TRIM card.
2
3
4
Using a flat-head screwdriver, attach the captive screws on the TRIM
Attach two Modulus front filler panels to the front of the slots filled by
the TRIM card.
The TRIM card supports only one LAN connection. Use either the
DB9 or the RJ45 connector to make the LAN connection, but do not
attach cables to both.
• If your LAN cable is an STP cable, attach it to the DB9
connector at the back of the TRIM card.
• If your LAN cable is a UTP cable, attach it to the RJ45
connector at the back of the TRIM card.
• If you are installing the TRIM card in a Modulus 21
enclosure, install the RFI suppression bar across the front
door of the enclosure. See the Preparing Modulus Enclosures
for RFI Suppression section.
• If you are installing a TRIM card in a Modulus 18 enclosure,
attach the RFI suppression screen to the inside of the front door.
section on page 2-49. The suppression screen replaces the
suppression bars.
2-46
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Card
Trim Card
Trim Card
Standoff
Interboard
Connector System
Header Pins
Bottom of Card
CPU Plus Board
Fastener Screw
(Solder Side)
Place the 4
non-ferrite pins toward
top of processor card.
Ferrite
Figure 2-13. Attaching the TRIM Card to the Processor Card
Attaching the
Cables
The LAN port is Port 55, regardless of how many active X.25, PAD, or MUX ports
are in your node. To configure the LAN port and for information about LAN
statistics, see the Vanguard ONS Basics Protocols Manual (T0106).
Installation
2-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Removing/Replacing TRIM Cards
Introduction
This section describes the removal and replacement of TRIM cards.
Caution
6500 cards and their components are sensitive to static discharge, which can damage
components. Use proper handling and grounding precautions, including the use of an
anti-static grounding strap, whenever you handle a card.
Before Removing
TRIM Cards
Before removing the TRIM card from the Modulus enclosure, disconnect the LAN
cable and detach the TRIM rear filler panel from the TRIM card backplane.
Failure to do so could damage the LAN cable or the TRIM card. The following
caution label on the processor card is a reminder:
“REMOVE LAN I/O CABLE, REAR FASTENERS AND FRONT FILLERS
BEFORE REMOVING THIS CARD.”
Removing the
TRIM/Processor
Card
Follow these steps to remove the TRIM/processor card from the nest:
Step
Action
1
2
Detach the LAN cable from the backplane.
Using a flat-head screwdriver, unscrew the captive hardware that
attaches the TRIM card rear filler panel to the TRIM card backplane.
3
4
Detach the two Modulus front filler panels that cover the TRIM card.
Pull out the TRIM/processor card. When detaching a TRIM card from
its processor card, follow the procedures in “Installing and Connecting
a TRIM Card” section on page 2-45 in reverse order.
• If you are removing or replacing a card in a Modulus 8/18
enclosure, refer to the Modulus Planning and Installation
Guide.
• If you are removing or replacing a card in a Modulus 9/21
enclosure, refer to the Modulus 9 and 21 Installation and
Operation Guide.
Updating LAN Port The BIA (Burned In Address) is a unique LAN MAC address that is supplied by a
MAC Address
PROM chip on the TRIM card. The BIA is used as the LAN port MAC address if the
Port MAC Address parameter (in the Port configuration record) is set to a default
value of 00-00-00-00-00-00.
If you replace the TRIM card, reboot the node to reset the LAN port address to the
new BIA value contained on the replacement TRIM card. If, however, you want to
use the BIA address from the removed card, update the node configuration to ensure
that the older BIA address is used.
2-48
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Preparing Modulus Enclosures for RFI Suppression
Introduction
To meet FCC requirements, the Modulus 18 and Modulus 21 enclosures require
special RFI suppression hardware. In the Modulus 18 enclosure, the RFI suppression
scheme differs depending on whether a TRIM card is installed in the unit.
Modulus 18 with
TRIM Card
Figure 2-14 shows a Modulus 18 enclosure with a TRIM card. It also shows the
suppression screen that you need to install.
Snap tab into spring rods
on top and bottom of door.
Modulus 18 Door
(Inside View)
Snap
remaining tab
to door.
Honeycomb Mesh RFI Screen
Figure 2-14. RFI Suppression Screen (Modulus 18 - with TRIM Card)
Installation
2-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Installing RFI
Suppression
Screen
If you have a Modulus 18 enclosure and at least one TRIM card, follow these steps
requirements:
Step
Action
1
Open the door of the enclosure. If the two RFI suppression straps
2
Place the screen flat against the inside of the door with the three
attachment points facing the inside of the door.
The edge with two attachment tabs aligns with the top and bottom
aligns with the inside of the door latch.
3
To install the screen, you can leave the door connected to the
enclosure. Swing the door open wide, and align the two tabs to the
top and bottom hinges. Press each point gently but firmly to make
solid connections. Then press the single tab to the door latch.
The screen is then in place.
Modulus 18: RFI
Suppression
without a TRIM
Card
If you have a 6500PLUS node in a Modulus 18 enclosure and there are no TRIM
cards, install two RFI (radio frequency interference) grounding straps to the front of
meet FCC requirements. The straps are not needed if at least one TRIM card is
installed in the enclosure.
Note
If you have older model 6500 nodes (non-6500PLUS nodes) installed in Modulus
21 enclosures, you must install similar RFI straps in the Modulus 21 enclosure as
well.
2-50
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Modulus 18 With
No Trim Card
Figure 2-15 shows a Modulus 18 with no TRIM cards and the RFI suppression
straps.
3 Align the top of strap so that
screw hole is over bar,
insert the screw, and tighten.
Remove a screw from
the left and right power supplies.
1
Tighten the bottom
screw.
4
Align the bottom of the
2
strap so it is over the screw hole,
insert the screw, and finger tighten.
Figure 2-15. RFI Suppression Straps (Modulus 18 - No TRIM Card)
Installation
2-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Nodes in Modulus Enclosures
Modulus 21 and
RFI Suppression
Bar
If you are installing a TRIM card in a Modulus 21 enclosure, add the RFI
the door.
Modulus 21 Door
(Inside View)
RFI Suppression Bar
This Side of Bar to
Face Inside of Door
Figure 2-16. RFI Suppression Bar (Modulus 21 Enclosure)
2-52
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Up the Node
Starting Up the Node
Introduction
Node Startup
After you install the node in the enclosure, you can start up the node.
Follow these steps to start up the node:
Step
Action
Result/Description
1
Power up the Modulus enclosure
by connecting the power cord to a processor card turn on as described
The front panel lights of the
suitable primary power source.
in the DSU DIM Installation
section.
After a few minutes, the green
STATUS light comes on to indicate
the node is ready to process calls.
If this does not occur, call your
VanguardMS representative.
2
Configure the unit through the
control terminal port (CTP) menus. terminal to Port 6. Port 6’s default
settings are standard terminal port
To access the CTP, attach a
values: 9600 baud, 8 data bits, 1
stop bit, no parity.
3
4
When the (*) prompt appears on
the terminal, type the following:
.ctp <CR>
At the password prompt, enter
<CR>.
This is the default password value.
The Main menu appears. See the
Vanguard ONS Basics Protocols
Manual (T0106) for configuration
information.
Installation
2-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing Processor Card Components
Introduction
You can upgrade and replace components on the 6500PLUS processor card. In both
standalone and Modulus enclosures, you can:
• Replace DIMs (data interface modules)
• Set jumpers on the port interface pins
• Install single in-line memory modules (SIMMs)
• Replace a FLASH module
• Replace the ID Module
• Replace PROMs
• Replace the CMEM chip
Processor Card
Note
The PROMs are located beneath the FLASH Module.
FLASH Module
PROM
SIMMs
DIMs
Port Interface Jumpers
(underneath FLASH Module)
Port 1
Port 2
U83
Trim
Card
U40
ID Module
CMEM Chip
Figure 2-17. 6500PLUS Processor Card
2-54
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing DIMs
Introduction
Description
There are two Data Interface Modules (DIMs) on a 6500PLUS processor card.
Each DIM is a 64-pin, dual in-line module that can be repositioned so that Ports 1 or
2 act as either DCE or DTE ports. For most cases, the DIMs are positioned so the
ports act as DCEs. One DIM corresponds to Port 1 and the other to Port 2
can purchase DIMs that will support V.35, V.36, and X.21 interfaces.
Replacement
Procedure
Use the DIM Extraction Tool (58862-01) provided with the accessory kit to perform
the following procedure. Do not use a screwdriver or other tool that may damage the
components on the card.
Caution
6500PLUS cards and their components are sensitive to static discharge, which can
damage components. Use proper handling and grounding precautions, including the
use of an anti-static grounding strap, whenever you handle a card.
Step
Action
1
Remove the TRIM card first if you are installing or replacing DIMs onto
a processor card that has an attached TRIM card.
Otherwise, there is no physical support to the processor card when you
insert the DIMs on the board.
2
removal strap to lift out the DIM. Be sure that you do not bend the pins
during removal.
3
4
5
Insert the DIM into the other set of parallel sockets if you are moving the
DIM to another position.
Insert the new DIM into the original location if you are just replacing a
DIM. Be sure the pins are seated firmly in the sockets and are not bent.
Reattach the TRIM card to the processor card.
Installation
2-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Example of DIM
Removal
Figure 2-18 shows DIM removal.
Plastic DIM Removal Strap
Front Panel
Port 1
Port 2
DCE
DTE
Figure 2-18. DIM Removal
New DIM
Installation
If you install a new type of DIM on the 6500PLUS processor card, you may need to
of the pins on the card.
2-56
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Jumpers
Figure 2-19 shows where the jumpers should be placed on the pins for various
applications and enclosures.
EIA 232 V.24
V.35, V.36, X.21 for Backplanes
with 26-Pin DB26 Connectors
V.35, V.36, X.21 for
Standalone and Backplanes
with 25-Pin DB25 Connectors
Figure 2-19. Jumpers on the Port Interface Pins
Installation
2-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Installing SIMMs
Introduction
The 6500PLUS processor card comes with 3 Mbytes of RAM on the card. You can add
shows the location of the SIMM slots on the 6500PLUS processor card.
Guidelines
•
Install SIMMs in pairs only.
• The 6500PLUS processor card is shipped with SIMMs in sockets U79 and U80.
Install additional SIMMs in sockets U81 and U82.
Installation
Procedure
Follow these steps to install a SIMM:
Caution
6500PLUS cards and their components are sensitive to static discharge, which can
damage components. Use proper handling and grounding precautions, including the
use of an anti-static grounding strap, whenever you handle a card
Step
Action
1
For proper operation, SIMMs must be in sockets U79 and U80
2
Press the SIMM into the socket.
Be sure it locks in place with the locking tab.
SIMM Removal
When removing a SIMM, pull against the side with the chips so it disengages from
the locking tabs.Then lift out the SIMM.
Installation
2-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Example of SIMM
Installation
Figure 2-21 shows how a SIMM is installed in a slot.
Insert SIMM into socket
at a slight angle.
Figure 2-21. SIMM Installation
2-60
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing FLASH Modules
Introduction
You can replace a FLASH module on a 6500PLUS processor card. The location of a
FLASH module is shown in Figure 2-17.
Caution
Use proper handling and grounding precautions, including the use of an anti-static
grounding strap, whenever you handle a card
Replacement
Procedure
Step
Action
1
Remove the card from the nest or enclosure.
You might have to wiggle the card until the header pins disengage
from the socket on the card.
2
a) Loosen and remove the four screws that hold the FLASH
module to the processor card.
b) Carefully lift the FLASH module from the 6500PLUS processor
card.
3
Using the old module as a guide, insert the header pins of the new
module.
4
5
Place the new module on the 6500PLUS processor card.
Insert the header pins into the socket. Seat the pins firmly into the
socket. Do not bend them.
6
Use four screws to secure the FLASH module to the 6500PLUS
processor card as shown. Do not overtighten the screws.
Installation
2-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Installation
Example
Figure 2-22 shows an example of a FLASH module installation.
FLASH Module
Header
Pins
PROMs
Card Socket
Figure 2-22. Flash Module Installation
2-62
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing ID Modules
Replace the ID
Module
Perform these steps to replace the ID Module:
Step
Action
1
2
Remove the card from the nest or enclosure.
notch, which is toward the front of the card.
This will help you orient the new chip.
3
4
Using a standard chip-puller, remove the ID Module.
Insert the new ID Module into the socket. Be sure that the notch in
the chip is oriented toward the front of the card.
Installation
2-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing PROM Chips
Replace PROM
Chips
Follow these steps to replace a PROM chip:
Step
Action
1
2
Remove the card from the nest or enclosure.
Loosen and remove the four screws that hold the FLASH module to
3
4
Carefully lift the FLASH module from the 6500PLUS processor card.
You may have to wiggle the card until the header pins disengage
from the socket.
notch on each chip and, using a standard chip-puller, remove the
PROMs.
This will help you orient the new chips.
Note
Not all four PROM sockets may have PROMs.
5
6
Insert the new PROMs into the sockets. Be sure that they are oriented
the same way as the old chips.
Place the FLASH module on the 6500PLUS processor card. Insert the
header pins into the socket.
The pins should seat firmly into the socket, but be careful not to bend
the pins.
7
On the other side of the 6500PLUS processor card, use four screws to
secure the FLASH module to the 6500PLUS processor card.
Do not overtighten the screws or you may damage the 6500PLUS
processor card.
2-64
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Processor Card Components
Replacing the CMEM Chip
Replace CMEM
Chips
Follow these steps to replace a CMEM chip:
Step
Action
Remove the card from the nest or enclosure.
1
2
On the CMEM chip, note the location of the dot in the lower left
corner, which is toward the front of the card. This will help you orient
the new chip.
3
4
Using a standard chip-puller, remove the CMEM chip.
Insert the new CMEM chip into the socket. Be sure that the dot in the
chip is oriented toward the front of the card.
Installation
2-65
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
DSU DIM Installation
Introduction
The DSU DIM is designed to be installed in the DTE position only. The DSU
option will not operate if the DIM is installed in the DCE position.
You can install up to two DSUs per platform using both ports 1 and 2.
Example of
Installing the DSU
DIM
Figure 2-23 shows the DSU DIM installation.
DSU DIM
Front Panel
Port 1
DCE
DTE
DCE
DTE
Port 2
Figure 2-23. DIM Installation
2-66
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
Installation
Procedure
Follow these steps to install the DSU DIM:
Step
Action
Install the DSU DIM in the DTE position only (see Figure 2-23).
1
The DSU option does not operate if the DIM is installed in the DCE
position.
2
Set the jumpers properly.
This option requires the jumpers be set for the high speed 1 setting
(M1/HS). This is the same jumper location listed for the V.35, V.36,
and X.21 interfaces on standalone or Modulus 8/18 hardware.
3
4
Plug the EIM into the backplane connector corresponding to the DIM
port containing the DSU DIM (Port 1 or 2). Verify that the EIM is
only connected to a port that has a DSU DIM installed.
Tighten the connector mounting screws to provide proper grounding
and ensure signal integrity.
Caution
Be sure that the telco plug is disconnected before the EIM is disconnected from the
6500PLUS. Also, do not connect the telco plug to the EIM until the EIM has been
connected to the 6500PLUS
.
Software supporting the DSU option is necessary for the 6500PLUS to recognize the
DSU hardware. The provided software requires an NSO or similar equipment to
(remotely) download the software, and a Flash card.
Control Terminal
Port
For configuration, reporting, and troubleshooting the CTP port must be used.
Network Management is not supported for the Integral DSU option.
Installation
2-67
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
Configuring the 6500PLUS for DSU Operation
Configuration
Procedure
You use the CTP to configure the DSU. Follow these steps to configure the 6500PLUS
for DSU operation:
Step
Action
1
Refer the Vanguard ONS Basics Protocols Manual (T0106). However,
you do not need to complete these configuration parameters:
• Clock Speed
• Connection Type
• Port Control
2
Configure the clock source parameter under port configuration as
follows:
• INT: Use this setting when providing clock to the network.
• EXT: Use this setting when using the network-provided clock
(usual mode for DSU operation).
2-68
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
DSU Input and Output Signaling
Introduction
The input and output signaling information is useful as a debugging tool and replaces
the EIA summary information associated with other DIM types.
Input Signals
This table describes the input signals.
NIS
Not In Service—This signal is normally low (L). If no signal is
received, or the DSU option is in DSU Loopback mode, or if idle codes
are received, NIS is listed as high (H). This signal is used to determine if
the other end of the connection is available.
BPV
Bipolar Violation—This signal is “H” during normal operation. When
the signal is “L,” it indicates that some type of bipolar violation was
received by the DSU option. The signal toggles during a DSU loopback
condition.
DL
C+
C-
DSU Loopback—This signal is normally “H.” An “L” indicates that a
DSU loopback mode is entered.
Positive Sealing Current*— This signal is “H” if the DC current on the
telephone company interface is not in the positive direction.
Negative Sealing Current* —This signal is “H” if the DC current on the
telephone company interface is not in the negative direction. An “L”
indicates that the DSU option has detected a negative “sealing” current
and is therefore performing a CSU loopback.
Note
When both C+ and C- are “H”, it indicates that no sealing current exists. This is
often the case when connected to other DSU type hardware. Normally, the signal
for C+ is “L” when connected to central office equipment (OCU hardware).
Output Signals
Although you cannot directly access the output signals, they are manipulated by the
DSU option software and may be useful for informational purposes. The following
table describes the output signals.
RS
Reset— This output resets the DSU option hardware. Its normal
operating state is “H.”
LL
Local Loopback — When this signal is “L”, the DSU hardware is
locally looping data back to the 6520 hardware by way of the EIM.
CL
CSU Loopback —When this signal is “L”, the DSU hardware is looping
the remote connection's receive to transmit.
IDL
CLK
Idle —An “H” on this signal tells the DSU hardware to send idle bipolar
violations to the remote system.
Clock Mode—The signal “H” denotes the use of the network clock. The
DSU option provides the clock when this signal is “L.”
You can view these signals using the control terminal Monitor menu item on the
Main menu within the CTP in the control terminal.
Installation
2-69
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
Other Reporting
Differences
Other differences in control terminal output are:
• Detailed Port Statistics— show DSU input and output signaling as well as
note the installed DSU DIM
• Detailed Node Statistics— show DSU DIM installation
Example of
Diagnostics Menu use this menu to access the loopback options described in the next section.
Node: nodename
Menu: Diagnostics
Address (blank)Date: -------- Time: ------
Path: (Main.12)
1. Local Loopback
2. V.54 Loopback 2
3. V.54 Loopback 3
4. Fatal Error Reports
5. Logged Alarms«
6. Startup Diagnostics
7. DSU Internal Loopback
8. DSU Internal and External Loopback
9. Start Delay Measurement
10. Stop Delay Measurement
11. Display Delay Summary
12. IP Ping
#Enter Selection:
Figure 2-24. Diagnostics Menu
Control Terminal
Loopback Options
The following table describes the control terminal loopback options.
DSU Internal Loopback This loopback mode does not affect the external
interface but it does loop the local transmit data back to
the receive data within the EIM. This test is useful for
verifying that the EIM is connected and is working
properly from a digital integrity perspective.
DSU Internal and
External loopback
This loopback mode performs the internal loopback
mentioned above along with looping the external
transmit to the external receive to allow manual testing
of the remote interface.
2-70
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
Troubleshooting DSU DIM Installation
Introduction
Some of the potential installation problems are listed below:
• Improper port connection of the EIM
• Improper telco interface connection
• DSU DIM not connected in DTE configuration
• Processor card jumpers not in HS1 mode
• DSU option software not operational
• DSU port clock source option not correct
• No signal from telco interface
CTP
Troubleshooting
The following information can be derived from the control terminal to aid in
troubleshooting.
Node Statistics
Port Statistics
Monitor
Used to verify that the software is a version which contains
the DSU option modifications. It also shows if the DSU DIM
is recognized by the software.
Used to verify that data is being sent without error. Error
counts may denote an error in clocking mode configuration.
It also shows if the DSU DIM is recognized by the software.
Input/output signals can be used to determine if the DSU
option is in a loopback mode requested by the remote end.
This would be an explanation for the inability to send data.
Continuous bipolar violations would also indicate the remote
system is out of service.
DSU Internal
Loopback
Failure of this loopback mode would indicate that the EIM
module is not connected.
Installation
2-71
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
DSU DIM FCC Information
Customer-Provided FCC regulations and telephone company procedures prohibit connection of
Telephone
Equipment
customer-provided equipment to telephone company-provided coin service (central
office-implemented systems). Connection to party lines is subject to state tariffs.
Occasionally, the telephone company may make changes in their equipment,
operations, or procedures. If these changes affect your equipment or service, the
telephone company will provide written notice so you can make the necessary
changes to maintain uninterrupted service.
Contact your telephone company if you have any questions about your telephone
line.
In some circumstances, the telephone company may ask you for information about
your equipment that is connected to the telephone line. Within the United States (at
the request of the telephone company), you should provide your equipment’s FCC
registration number. This number is located on the unit’s label.
FCC and Telephone Before the 6500PLUS DSU option can be connected to the network, the local
Company
Procedures and
Requirements
operating company must have the equipment’s registration number, and the proper
connections must be ordered.
To order the proper service, provide the telephone company with the following
information:
• USOC number of the required jack (shown below)
• Facility interface codes
• Service code
Type of Interface
USOC Jack
Connector
REN/Service
Code
Facility Interface
Code
56-kbps digital
interface
RJ48S
6.0F
04DU5-56
Regulations
Concerning
Electromagnetic
Radiation
The Federal Communications Commission (FCC) of the United States of America
and the Industry and Science Canada (ISC), have published regulations which
govern the allowable limits of emanation of radio frequency energy of computing
devices and associated peripherals. These regulations are concerned with
interference to radio communications, such as radio and television. The regulations
require equipment for use in the United States or Canada to be labeled and to be
accompanied by the following notice:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against interference when equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause interference to radio communications.
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the radio interference regulations of the ISC.
2-72
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DSU DIM Installation
Operation of this equipment in a residential area is likely to cause interference in
which case the user will be required to take adequate measures to correct the
interference.
This product was verified under test conditions that include use of shielded DTE
cable(s). Leased line cables with 1.5 turns through a ferrite cylinder were also used.
Use of different cables will invalidate verification and increase the risk of causing
interference to radio and TV reception.
You can obtain the proper cables from VanguardMS.
If this equipment causes interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorienting the receiving antenna
• Relocating the equipment with respect to the receiver
• Moving the equipment away from the receiver
• Plugging the equipment into a different outlet so that the equipment and
receiver are on different circuits
If necessary, you should consult the dealer or an experienced radio/television
technician for additional circuits.
You may find the following booklet prepared by the FCC helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is available from
the U.S. Government Printing Office, Washington, D.C. 20402, Stock No.
004-000-00345-4.
If Problems Arise
If any of your equipment is not operating correctly, immediately remove it from the
Installing the DSU telephone line before it harms your network. If the telephone company notes the
DIM
problem, they may temporarily disconnect your service. They will notify you in
advance of the disconnection, when possible. If advance is not feasible, you will be
notified as soon as possible. When you are notified, you will be given the chance to
correct the problem and be informed of your right to file a complaint with the FCC.
If your 6500 IFX needs repairs, they should be performed by VanguardMS or an
authorized representative of VanguardMS. For information, contact the VanguardMS
Customer Support Center at 1-800-544-0062.
Installation
2-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-Up Verification
Power-Up Verification
Introduction
The front panel lights on the different 6500PLUS cards help you isolate a problem.
These sections describe the light display when the enclosure is powered up.
Normal Sequence The following list describes what you see on the front panel if the power-up
sequence is performed correctly.
• POWER light comes on (processor and I/O cards).
• WATCHDOG light flashes briefly.
• TEST light flashes briefly.
• STATUS light comes on.
• PORT/DATA OUT lights come on and go off in sequence.
• If:
- You have an NSO card, one or more of the MEM (memory) lights come on.
- There is a disk in the drive, the drive light comes on as data is loaded into
the node.
This entire process may take a few minutes if an NSO card is loading data.
When the node passes the internal tests, the STATUS light (processor and I/O cards)
comes on. This indicates that the node is ready to process calls. You may also see
some of the port lights remain on depending on their configuration.
Checking the
Lights
If you want to make sure that all the lights are working, press the Lamp Test button
on the processor card. All the lights in the node momentarily come on.
Failed Sequence
The following describes what happens if the node does not come up.
Event
Result/Description
If the TEST light comes on and remains There is a hardware problem with the
on, the node failed one or more of the
diagnostic tests.
card (processor and I/O cards).
Reboot the node by pressing the RESET This reruns the internal diagnostic tests.
button.
If...
Then...
The TEST light
comes on again
Contact your Van- Otherwise, check the Status and
guardMS
Statistics menus.
and this is the first representative.
time the node is
turned on
Caution
Pressing the RESET button disrupts communication for the entire node.
If the WATCHDOG light on a processor card comes on and remains on, the card is
an auxiliary processor card. This card must be enabled from a control terminal.
2-74
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-Up Verification
Power-Up
Diagnostics
In the event of major problems that affect the entire node, you can reboot a node to
initiate the power-up diagnostics. After the power-up diagnostics are complete,
check the Statistics screens to see the results
To initiate power-up diagnostics, press the RESET button on the 6500PLUS processor
card's front panel or issue a cold Node Boot from the control terminal.
Installation
2-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Node to Default Configuration
Setting Node to Default Configuration
Introduction
You can set a node to the default configuration in two ways:
• Set the DFLT switch on the front panel
• Select the Default Node selection from the CTP Main menu
Defaulting the
Node
Follow these steps to default the node using the DFLT switch:
Step
Action
1
2
Push the DFLT switch to the left and press the RESET button.
Push the DFLT switch to the right when the STATUS light turns
steady on and press the RESET button.
3
Push the DFLT switch back to the left when the STATUS light turns
steady on and press the RESET button.
When the STATUS light turns steady on, the node is set to default
values.
For more information about the Default Node menu option, see the
Vanguard ONS Basics Protocols Manual
2-76
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Installing Software Options
Introduction
The 6500PLUS contains all the software options available for the current release of the
product. To access an option, however, you need to purchase the Software
Authorization Key (SAK) for that option. Each option has its own SAK and each
SAK can be used on only one specific node.
How to Get a SAK If you purchased the option with the 6500PLUS processor card, your VanguardMS
sales representative will supply the SAK for the option on that card. To purchase an
option for an existing 6500 card, provide your VanguardMS ales representative with
the software serial number of the ID Module in the 6500PLUS processor card.
There are two ways to get the serial number:
• From a node that is already running, access the Node Statistics.
• From the Software Acknowledgment Sheet that ships with the hardware.
Installation
2-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Accessing Node Serial Number from Node Statistics
Access Serial
Number
Perform these steps to find the SAK serial number using the Node Statistics:
Step
Action
Result/Description
1
Access the CTP by entering the
following at the * prompt:
You are prompted to enter the
password.
.ctp <CR>
2
Enter the password.
The default password is <CR>.
After you enter the password, the
Main menu appears.
3
4
From the Main menu, select
Status/Statistics.
Select Node Stat.
The Node Statistics consists of
several screens. The 6500PLUS
processor's serial number is on
the third screen, as shown in
Note
Multi-CPU card serial numbers
appear on subsequent screens.
5
a) Take this serial number and if
the card is a:
6505PLUS, add a -1 (dash 1)
6507PLUS, add a -2 (dash 2)
6525PLUS, add a -3 (dash 3)
b) Give the serial number with
the dash number to the Van-
guardMS sales
representative.
2-78
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Node Stat Screen
Figure 2-25 shows an example of the Node Stat screen.
Serial Number Needed for SAK
Node: Nodename Address: (blank)
Detailed Node Statistics
Date: -------- Time: ------
Page: 3 of 7
Board 1: Board Type: CPU+ Number of ports: 6 Status: Running
Serial #: 1806280
Memory Configuration:
EPROM: 1.0 MBytes
FLASH: 2.0 MBytes
DRAM: 1.0 MBytes
Used: 0
Flash Memory:
Software:
Port Configuration:
Port 0 DIM:
Port 1 DIM:
EIA-232-D
EIA-232-D
DCE
DCE
CPU Throughput:
CPU utilization: 14%
Current
Maximum
Characters/sec:
Packets/sec:
Buffer Usage:
0
0
55
1
33 (0%)
44 (1%) Available: 3978
Press any key to continue (ESC to exit ) ...
Figure 2-25. Serial Number on Node Stat Screen
Installation
2-79
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Enabling A Software Access Key
Follow These
Steps...
Follow these steps to enter the number at the node's control terminal:
Step
Action
Result/Description
1
Access the CTP. One way to do
this is to connect a terminal to a
local PAD port (Port 6), and enter
the following at the * prompt:
You are prompted to enter the
password.
.ctp <CR>
2
3
Enter the password.
The default password is <CR>.
After you enter the password, the
Main menu appears.
From the Main menu, select
Configure.
4
5
Select Software Key Table.
At the *Key Value prompt, enter
the SAK.
If...
Then...
You change the The option is
SAK number or disabled.
enter the wrong
one by mistake
You make a
mistakeentering entry by
the SAK pressing the
Blank out the
space bar and
enter the SAK
number again.
Note
6
Boot the node to implement the
option.
You need a separate SAK for each
node in which the option is to be
enabled.
After you receive the printed version of the SAK, save a copy in a safe place in case
you have to enter it again.
2-80
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Installing New Software Options in an Existing Network
Install New
Software
Follow these steps if you are installing new software options in an existing network
and you want to get the serial number for a remote node at a central site:
Step
Action
Place a call to the CTP at a remote node.
Log in to the remote node.
1
2
3
Access the Node Stats and get the serial number.
If you configure the key remotely, boot the node to activate the link.
The link will go down during the node boot.
Installation
2-81
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Software Options
Enhanced LAN Option
Enhanced LAN
Option
The Enhanced LAN Option is a Software Authorization Key (SAK) that enables IPX
Routing and AppleTalk features for the 6520 and Vanguard 300, and provides IP
Routing/SNMP for the 6500PLUS
.
What It Does for
the 6520 and
Vanguard 300
The Enhanced LAN Option enables IPX Routing and AppleTalk features for the
6520 and Vanguard 300, if present in the software image that is loaded.
IP Routing is now available in all base software packages. A SAK is no longer
required to enable this feature.
What It Does for
the 6500PLUS
The Enhanced LAN Option provides a CSK IP Routing/SNMP for the 6500PLUS
This CSK enables the full IP Routing capability for SNMP management across a
WAN link or Token Ring if present, with the use of the full router for Release 4.50
(configuration of the IP/Routing SAK is no longer required).
.
CSK Information
Guidelines
The IP Routing/SNMP Customer Software Key (CSK) for the 6500PLUS product is:
SG6CUJEQ6MYTGU4XRFKP
If you already have the IP/Routing SAK configured, you do not have to configure the
new CSK.
The Enhanced LAN Option is available for purchase as a SAK. You must install the
CSK for IP Routing/SNMP for the 6500PLUS on each node on which you want to
perform IP Routing/SNMP.
2-82
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Cables
Introduction
The tables in this appendix describe the pinouts for ports on Standalone, Modulus
8/18, and Modulus 9/21 enclosures and include this information:
• Standalone, Modulus 8/18, and 9/21 enclosures: EIA 232-D signals with V.24
DIMs on the processor card
• Modulus 9/21 enclosures: V.35/V.36 signals with V.35/V.36 DIMs on the
processor card
• Modulus 9/21 enclosures: V.11 signals with X.21 DIMs on the processor card
• Standalone and Modulus 8/18 enclosures: V.35/V.36 signals with V.35/V.36
DIMs on the processor card
• Standalone and Modulus 8/18 enclosures: V.11 signals with X.21 DIMs on the
processor card
• Standalone and Modulus 8/18 enclosures: EIA 232-D crossover cable
• Token Ring LAN STP (shielded twisted pair) cable pinouts
• Token Ring LAN UTP (unshielded twisted pair) cable pinouts
The descriptions of EIA 232 pinouts apply to all 6500 cards. However, V.35, V.36,
and X.21 interfaces are available only on the first two ports on a 6500PLUS processor
card. For example, in a multi-processor node, Ports 1 and 2 on the first processor
card could be configured (with the DIMs and jumpers) for V.35, and Ports 7 and 8 on
the second processor card could also be configured (with the DIMs and jumpers)
for V.35.
The arrows in the tables indicate the direction of the port signal, as follow:
<-------------- indicates an input signal to the port
---------------> indicates an output signal from the port
Cables
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
EIA 232-D Signals (Standalone, Modulus 8/18, and 9/21 Enclosures)
Pin
DCE
Position
Function/Signal
Name
Pin
DTE
Position
Function/Signal
Name
1
---------------
<-------------
------------->
<-------------
------------->
------------->
---------------
Shield/Frame Ground
1
2
3
4
5
6
7
---------------
------------->
<-------------
------------->
<-------------
<-------------
---------------
DCD
Shield/Frame Ground
2
3
4
5
6
7
TXD
TXD
RXD
RXD
RTS
RTS
CTS
CTS
DSR
DSR
Signal Ground
Signal Ground
8---------------
DCD
<-------------
------------->
8 <-------------
14
15
DATA RESTRAINT
14
------------->
<-------------
DATA RESTRAINT
TRANSMIT CLOCK 15
or V.54 Loop 3 *
TRANSMIT
CLOCK
16
17
------------->
------------->
STANDBY
INDICATOR
16
<-------------
<-------------
STANDBY
INDICATOR
RECEIVE CLOCK
17
RECEIVE CLOCK
18<-------------
EXTERNAL
18------------->
EXTERNAL
RECEIVE CLOCK
RECEIVE CLOCK
or V.54 Loop 3 *
20
21
22
24
<-------------
DTR
20
21
22
------------->
DTR
------------->
<----------->
<------------
V.54 Loop 2
RI/TM *
------------->
NC
V.54 Loop 2
(No Connection)
EXTERNAL TRANS- 24
MIT CLOCK
------------->
EXTERNAL
TRANSMIT
CLOCK
25
<-------------
TEST MODE
25
<-------------
MAKE BUSY
* Pin assigned double function as follows:
Pin 15: Outputs TRANSMIT CLOCK if the port is configured for internal clocks. Otherwise it acts
as a V.54 Loop 3 signal when connected to a modem.
Pin 22: Used as the Ring Indicator output if the port is configured to emulate a dial modem. For this
to work properly, the RI/TM switch of the port must be set to RI. When the RI/TM switch is set to
TM, this pin acts as an input, and the TM output from the attached modem (pin 25 on the modem)
comes into the 6500 on this pin.
A-2
Cables
Download from Www.Somanuals.com. All Manuals Search And Download.
V.35/V.36 (Modulus 9/21 Enclosures)
Pin
DCE
Position
Function/
Signal Name
Pin
DTE
Position
Function/
Signal Name
1
---------------
<-------------
SHIELD/FRAME
GROUND
1
--------------
------------->
SHIELD/FRAME
GROUND
2
TRANSMITTED
DATA A
2
3
TRANSMITTED
DATA A
3
4
5
6
7
------------->
<-------------
------------->
------------->
---------------
RECEIVED DATA A
<-------------
------------->
<-------------
<-------------
---------------
RECEIVED DATA A
REQUEST TO SEND
CLEAR TO SEND
DATA SET READY
SIGNAL GROUND
REQUEST TO SEND 4
CLEAR TO SEND
DATA SET READY
SIGNAL GROUND
5
6
7
8------------->
DATA
CARRIER
8<-------------
DATA
CARRIER
DETECT
DETECT
13 ------------->
14 <-------------
15 ------------->
TRANSMIT CLOCK 13
B
<------------
------------->
<-------------
TRANSMIT CLOCK
B
TRANSMITTED
DATA B
14
TRANSMITTED
DATA B
TRANSMIT CLOCK 15
A
TRANSMIT CLOCK
A
16 ------------->
17 ------------->
18NC
RECEIVED DATA B 16
RECEIVE CLOCK A 17
<-------------
<-------------
RECEIVED DATA B
RECEIVE CLOCK A
(No
Connection)
18 ------------->
LOOP
3
(V.36 ONLY).
19 ------------->
20 <-------------
RECEIVE CLOCK B 19
<-------------
------------->
RECEIVE CLOCK B
DATA TERMINAL
READY
20
21
23
DATA TERMINAL
READY
21 <-------------
23 <-------------
LOOP 2
------------->
------------->
LOOP 2
(V.36 ONLY).
(V.36 ONLY).
EXTERNAL
EXTERNAL
TRANSMIT CLOCK
B
TRANSMIT CLOCK
B
24 <------------
25 NC
EXTERNAL
TRANSMIT CLOCK
A
24
25
------------->
<------------
EXTERNAL
TRANSMIT CLOCK
A
(No Connection)
TEST MODE
(V.36 ONLY)
Cables
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
V.11 Signals (Modulus 9/21 Enclosures)
Pin
DCE
V.11
Function/Signal
Name
Pin
1
DTE
Function/Signal
Name
Position
Position
1
---------------
<-------------
SHIELD/FRAME
GROUND
---------------
------------->
SHIELD/FRAME
GROUND
2
T (A) TRANSMITTED
DATA A
2
TRANSMITTED
DATA A
3
4
6
7
------------->
<------------
------------->
--------------
R (A) RECEIVED DATA A
C (A) CONTROL A
3
4
6
7
<-------------
------------->
<-------------
---------------
8<------------
RECEIVED DATA A
CONTROL A
I (B) INDICATION B
SIGNAL GROUND
INDICATION B
SIGNAL GROUND
8------------->
I
(A) INDICATION
A
INDICATION
A
13 ------------->
14 <------------
15 ------------->
S (B) TRANSMIT CLOCK 13 <------------
B
TRANSMIT CLOCK
B
T (B) TRANSMITTED
DATA B
14 ------------->
TRANSMITTED
DATA B
S (A) TRANSMIT CLOCK 15 <------------
A
TRANSMIT CLOCK
A
16 ------------->
17 ------------->
19 ------------->
20 <-------------
23 <-------------
R (B) RECEIVED DATA B 16 <------------
RECEIVED DATA B
RECEIVE CLOCK A
RECEIVE CLOCK B
CONTROL B
*
*
RECEIVE CLOCK A 17 <-------------
RECEIVE CLOCK B 19 <-------------
C (B) CONTROL B
20 ------------->
23 ------------->
X (B) EXTERNAL
EXTERNAL
TRANSMIT CLOCK
B
TRANSMIT CLOCK
B
24 <-------------
X
(A)
EXTERNAL
TRANSMIT CLOCK
A
24 ------------->
EXTERNAL
TRANSMIT CLOCK
A
* These V.11 signals are not used in the X.21 standard.
A-4
Cables
Download from Www.Somanuals.com. All Manuals Search And Download.
V.35/V.36 Signals (Standalone and Modulus 8/18 Enclosures)
Pin
DCE
Position
Function/
Signal Name
Pin
DTE
Position
Function/
Signal Name
1
--------------- SHIELD/FRAME
GROUND
1
--------------- SHIELD/FRAME
GROUND
2
3
4
5
6
7
<------------- TRANSMITTED DATA A
-------------> RECEIVED DATA A
<------------- REQUEST TO SEND
-------------> CLEAR TO SEND
-------------> DATA SET READY
--------------- SIGNAL GROUND
2
3
4
5
6
7
--------------> TRANSMITTED DATA A
<------------- RECEIVED DATA A
-------------> REQUEST TO SEND
<------------- CLEAR TO SEND
<------------- DATA SET READY
--------------- SIGNAL GROUND
8-------------> DATA
13 -------------> TRANSMIT CLOCK B
14 <------------ TRANSMITTED DATA B 14 -------------> TRANSMITTED DATA B
15 -------------> TRANSMIT CLOCK A
16 -------------- RECEIVED DATA B
17 -------------> RECEIVE CLOCK A
18-------------> RECEIVE CLOCK
CARRIER
DETECT 8<------------- DATA
CARRIER
DETECT
13 <------------- TRANSMIT CLOCK B
15 <------------- TRANSMIT CLOCK A
16 <------------- RECEIVED DATA B
17 <------------- RECEIVE CLOCK A
B
18<------------- RECEIVE
CLOCK
B
19 -------------> RECEIVE CLOCK B
19 <------------- RECEIVE CLOCK B
20 <------------- DATA TERMINAL
READY
20 -------------> DATA TERMINAL
READY
21 -------------> TRANSMIT CLOCK B
21 <------------- TRANSMIT CLOCK B
22 <------------- EXTERNAL TRANSMIT 22 -------------> EXTERNAL TRANSMIT
CLOCK B CLOCK B
24 <------------- EXTERNAL TRANSMIT 24 -------------> EXTERNAL TRANSMIT
CLOCK A
CLOCK A
25 NC
(No Connection)
25 <------------- TEST MODE
(V.36 ONLY).
Cables
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
V.11 Signals (Standalone and Modulus 8/18 Enclosures)
Pin
DCE
Position
V.11
Function/Signal
Name
Pi
n
DTE
Position
Function/Signal
Name
1
--------------
<------------
------------>
<------------
SHIELD/FRAME
GROUND
1
-------------
-------------
<------------
----------->
SHIELD/FRAME
GROUND
2
3
4
T
TRANSMITTED
(A) DATA A
2
3
4
TRANSMITTED
DATA A
R
(A)
RECEIVED DATA A
RECEIVED DATA A
C
CONTROL A
CONTROL A
(A)
6
7
------------>
--------------
I (B) INDICATION B
SIGNAL GROUND
(A) INDICATION
6
7
<------------
--------------
8<------------
INDICATION B
SIGNAL GROUND
8------------>
I
A
INDICATION
A
13
14
15
16
17
----------->
S
(B)
TRANSMIT CLOCK 13 <------------
B
TRANSMIT CLOCK
B
<-----------
T
TRANSMITTED
14 ------------>
TRANSMITTED
DATA B
(B) DATA B
------------>
------------>
------------>
S
(A)
TRANSMIT CLOCK 15 <------------
A
TRANSMIT CLOCK
A
R
(B)
RECEIVED DATA B 16 <------------
RECEIVED DATA B
*
RECEIVE CLOCK A 17 <------------
RECEIVE CLOCK A
18------------>
*
RECEIVE
RECEIVE CLOCK B 19 <------------
CONTROL B 20 ------------>
CLOCK
B
18<------------
RECEIVE
CLOCK
B
19
20
------------>
*
RECEIVE CLOCK B
CONTROL B
<-----------
------------>
<-----------
C
(B)
21
22
S(B) TRANSMIT CLOCK 21 <------------
B
TRANSMIT CLOCK
B
X
EXTERNAL
22 ------------>
EXTERNAL
(B) TRANSMIT CLOCK
B
TRANSMIT CLOCK
B
24
<------------
X
EXTERNAL
24 ------------>
EXTERNAL
TRANSMIT CLOCK
A
(A) TRANSMIT CLOCK
A
*These V.11 signals are not used in the X.21 standard.
A-6
Cables
Download from Www.Somanuals.com. All Manuals Search And Download.
P1
P2
1
1
2
3
3
2
4
8
5
6
7
14
20
7
8
4
14
15
17
1815
20
22
24
25
16
21
5
18
24
6
25
17
22
21
16
Pin
Function
Receive+
1
6
5
9
Receive–
Transmit–
Transmit+
NOTE: All other pins are reserved and
should remain unconnected.
Pin
Function
Receive+
4
5
3
6
Receive–
Transmit–
Transmit+
NOTE: All other pins are reserved and
should remain unconnected.
Cables
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Specifications
Introduction
This section describes the physical and environmental specifications and power
requirements for the enclosures.
Additional
Information
For more information about Modulus 8/18 enclosures, refer to the Modulus Planning
and Installation Guide (Product Code 80300). For Modulus 9/21 enclosures, see the
Modulus 9 and 21 Installation and Operation Guide (Part No. 09564, Rev. B).
Physical
Characteristics
Unit
Dimensions
6500 Standalone Enclosure
Height: 2.75 in. (6.99 cm)
Width: 8.54 in. (21.69 cm)
Depth: 16.00 in. (40.64 cm)
Weight: 5.00 lb (2.3 kg)
Modulus 8
Modulus 18
Modulus 9
Height: 14.0 in. (35.6 cm)
Width: 8.5 in. (21.6 cm)
Depth: 22.0 in. (55.9 cm)
Weight (Empty): 32 lb (14.5 kg)
Max Number of 6500 Product Cards: 4
Height: 14.0 in. (35.6 cm)
Width: 19.0 in. (48.3 cm)
Depth: 22.0 in. (55.9 cm)
Weight (Empty): 40.5 lb (18.4 kg)
Max Number of 6500 Product Cards: 8
Height: 14.5 in. (36.8 cm)
Width: 8.7 in. (22.1 cm)
Depth: 20.5 in. (52.1 cm)
Weight (Empty): 35 lb (15.9 kg)
Max Number of 6500 Product Cards: 4
Specifications
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Unit (continued)
Modulus 21
Dimensions
Height: 14.0 in. (35.6 cm)
Width:17.8 in. (45.2 cm)
Depth: 20.75 in. (52.7 cm)
Weight (Empty): 48 lb (21.8 kg)
Max Number of 6500 Series Product
Cards: 9
Power
Requirements
Standalone Enclosure
Modulus 8
100-240 VAC nominal, 47 to 63 Hz
100-120 VAC, 8.0 A, 50 to 60 Hz
220-240 VAC, 6.0A, 50 to 60 Hz
Modulus 9
100-120 VAC, 5.0A, 50 to 60 Hz
220-240 VAC, 3.0A, 50 to 60 Hz
Modulus 18 and Modulus 21
100-120 VAC, 10.0A maximum, 50 to
60 Hz
220-240 VAC, 6.0A maximum, 50 to
60 Hz
Modulus 18, -48 VDC Power
Supply Module
-48 to -60 VDC, 10.0A maximum
Modulus 21, -48 VDC Power
Supply Module
Power Rating for 6500PLUS
-48 to -60 VDC, 15.0A maximum
18.5
Processor Card with TRIM Card
Environmental
Limits
• All enclosures, 6500 CPU, 6500PLUS processor, 6500 I/O cards: 0° C to 50° C
(32° F to 122° F)
• 6500 NSO card: 0° C to 45° C (32° F to 113° F)
• Storage Temperature: –40° C to 70° C (–40° F to 158° F)
• Relative Humidity: 5% to 90% (noncondensing)
B-2
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
F
Audience i
Features
FLASH module
B
replacement 2-61
Backplane 1-5
BIA 1-15
updating 2-48
H
BPV
Hardware 1-3
enclosure 1-4
C
specifications B-1
C-
C+
CL
CLK
Configuration
I
IDL
idle 2-69
Input signals
BPV 2-69
C+ 2-69
DL 2-69
NIS 2-69
Installation
D
guidelines 2-67
processor cards
SIMM 2-59
DIM
installation 2-55
DL
DTE 2-67
L
E
updating 2-48
LL
Loopback
Enclosure
Modulus 1-4
standalone 1-4
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
M
Replacing cards
RS
MAC address
updating 2-48
Modulus 18
reset 2-69
description 1-5
S
SAK 2-77
entering 2-80
SIMM
installation 2-59
N
Software options
installation 2-77
Software upgrade
NIS
Special notices
O
description ii
Output signals
CL 2-69
Specifications B-1
Standalone enclosure
installing 2-21
Starting up
CLK 2-69
IDL 2-69
LL 2-69
RS 2-69
P
Support cards
Pinouts A-1
Port interface pins
jumpering 2-56
Power-up
T
diagnostics 2-75
verification
failure 2-74
components
(figure) 1-14
cabling 2-46
installation 2-45
SIMM 2-59
installation
Troubleshooting
R
RAM
installation 2-59
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|