Download from Www.Somanuals.com. All Manuals Search And Download.
Included with the XC800 Series Phone
If any of these items are missing or damaged, contact Uniden Parts Department at: (800) 554-3988,
8:00 am to 5:00 p.m. Central, Monday through Friday.
Handset
Base
Rechargeable Battery
AC Adapter
Short Telephone Cord
Long Telephone Cord
• Precautions and Important Safety Instructions
• This Owner’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
1. Talk Button T
2. Numeric Keypad
3. Tone Key
4. Memory Key M
5. Ringer and Earpiece Volume V and
Ringer Key G
6. Talk/Batt Low Indicator
7. Flash/Redial Key r
8. Channel Select Key C
9. Pause
P
10. Tone Pulse switch
11. Telephone Jack In
12. AC Adapter Jack In
13. Status (in use) Indicator
14. Page/Find Key
11
12
10
status
13
14
page/find
Extend•A•Phone
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Selecting a Location
Wall Installation
Before choosing a location for your new phone,
read the “Installation Considerations” included in
the “Precautions and Important Safety
Instructions” brochure.
Standard Wall Plate Mounting
These phones are designed to be mounted on a
standard AT&T or GTE wall plate.
1. Plug the AC adapter into
the base.
Applying Power to the Base
All the XC800 Series phones require the included
AC adapter and an AC outlet that is not controlled
by a wall switch. To relieve strain on the DC plug
when the phone is placed on a desk or table,
connect the adapter as shown below.
2. Place the AC adapter cord
inside the molded channel.
Wrap the power cord
around the convenient
notch on the bottom.
Important: Place the
power cord so that it
does not create a trip
hazard, or where it could become chafed and
create a fire or other electrical hazards.
Desk or Tabletop Installation
1. Place the base on a desk or tabletop.
3. Plug one end of the short
telephone cord into the
TEL LINE jack on the base.
2. Plug the AC
adapter cord into
the 9V DC input
jack on the base.
3. Place the AC adapter
cord around the
strain relief.
4. Place the
telephone cord
inside the molded
channel on the
bottom of
the base.
Then plug the
other end of the
telephone cord
into the modular
jack on the wall.
4. Plug one end of
the long
telephone cord
into the TEL LINE
jack on the base.
5. Plug the other end of
the cord into the wall
telephone jack.
5. Place the base on the posts of the wall plate
and push down until it’s firmly seated.
6. Plug the AC adapter into a standard 120 VAC
wall outlet.
6. Plug the AC adapter into a standard 120 VAC
wall outlet.
Note: Do not use an outlet controlled by a wall switch.
Note: Do not use an outlet controlled by a wall switch.
Use only the Uniden AC adapter supplied
with this phone.
Direct Wall Mounting
If you do not have a standard wall plate, you can
mount your phone directly on a wall. Before
mounting your phone, consider the following:
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the cord inside the
molded channel on the
bottom of the base.
• Select a location away from electrical cables,
pipes, or other items behind the mounting
location that could cause a hazard when inserting
screws into the wall.
• Make sure the wall material is capable of
supporting the weight of the base and handset.
• Use #10 screws with anchoring
devices suitable for the wall material
where the base will be placed.
1. Insert two mounting screws
15
3
16 inches apart. Allow
6. Place the base on the
screws and push down
until it’s firmly seated.
3
about
of an inch between
the wal1l6 and screw heads for
mounting the phone.
2. Plug the AC adapter into
the base.
7. Plug the other end of the telephone line cord
into the wall jack.
3. Place the AC adapter cord
inside the molded channel.
8. Plug the AC adapter into a standard 120 VAC
wall outlet.
Note: Do not use an outlet controlled by a
wall switch.
Setting the Handset Retainer
The handset retainer holds the handset in place if
your phone is mounted on a wall. The steps
below describe how to remove and replace the
retainer so that the tab faces up.
4. Plug one end of the long
telephone cord into the
TEL LINE jack on the
base.
1. Push up on the
handset retainer on
the base, and slide
the tab out.
2. Flip the retainer
over so the tab
faces up.
3. Put the retainer
back into its slot
on the base.
4. Push down on
the handset retainer
until it snaps into
place.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Phone
Extending the Antenna
Cleaning the Battery Contacts
Before using your phone, be sure to raise its
antenna to the vertical position.
Then, fully extend the antenna.
To maintain a good
charge, it is important
to clean all charging
contacts on the
handset and base
Installing the Handset Battery Pack
1. Press in on the battery
cover release.
about once a month.
Use a pencil eraser or
other contact cleaner.
Do not use any
liquids or solvents.
Charging the Battery Pack
2. Slide the battery
Initial Battery Charging
compartment cover down.
The rechargeable Nickel-Cadmium battery pack
must be fully charged before using your phone
for the first time. We recommend that the battery
pack charge for approximately 15-20 hours,
without interruption, before plugging the phone
line into your new phone.
Place the handset
on the base. Either
place the handset
with the earpiece in
the cradle.
3. Align the plastic
connector of the
Nickel-Cadmium
battery pack with
its socket and plug
it in.
—OR—
Place the handset in the
cradle with it standing on
end (desk mount only) .
Note: The black lead
will be on the right
when the plug is
properly aligned.
Note: Make sure to change the
handset retainer before
hanging up the phone (wall
mounted bases).
4. Place the battery pack inside
the battery compartment,
and slide the battery
cover back on.
Battery Memory Effect
Rechargeable batteries can develop a “memory”
(reduced charge capacity) caused by repeated
charge and discharge cycles. The battery life will
seem to be shorter every time you use the unit.
Note: The built-in memory backup feature allows
up to 3 minutes to disconnect the old battery pack
and install a new one without losing any
numbers stored in memory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Most phone systems are tone dialing. Check
with your local phone company if you are not
sure whether your system is tone or pulse dialing.
To Avoid this Memory Effect
At least once a month, operate the unit until the
“Battery Low” indicator appears. Then recharge
the battery for a full 15 - 20 hours. Avoid putting
the handset back in the base after using the phone
for a short time. This could cause “topping off”
the charge.
Adjusting Ringer Controls
To adjust the ringer volume of your handset,
press G when the phone is not in use.
You can also select one of two different ringer
tones for the handset.
Low Battery Indicator
When the battery
pack in the handset is
very low and needs to
be charged, the
talk/batt low
Press G to select a different ringer tone when
the phone is not in use.
Adjusting Handset Receiver Volume
LED flashes.
Volume settings are “normal” and “high.” When
the handset is first picked up, the volume will be
at the “normal” setting. Pressing the
will
V
change the volume to “high.” This can be done
during a call.
If the talk/batt low LED begins to flash, the phone is
programmed to eliminate its functions to save
power. The table below describes how to return
your phone to normal operation.
Automatic Digital Code Security
To avoid unauthorized calls on your phone, a
digital code feature was added to all XC800 Series
phones. This digital code is shared only between
the handset and base. The code is set
During a Call
In Standby Mode
None of the buttons will operate.
Only the T button operates.
The handset beeps and the
talk/batt low LED flashes once
every 3 seconds.
The handset talk/batt low LED
flashes once every 3 seconds.
automatically when you first use the phone.
To change the digital code, be sure the handset is
on the base, then:
Complete your call as quickly
as possible.
You will not be able to make a
call.
1. Press the page/find button on the base.
Return the handset to the base
for charging.
Return the handset to the base
for charging.
2. After the handset stops beeping, remove it
from the base.
Note: Allow 15 to 20 hours without any
interruption for the handset to fully recharge.
3. Wait 5 seconds, then place the handset on
the base.
4. The status LED blinks to indicate that the digital
Setting the Pulse/Tone Switch
security code is set.
Be sure the
If the base loses power while the handset is off
the base, the digital code may be erased. When
this happens, the handset will not function. To
reestablish communication between the handset
and base:
PULSE/TONE switch
is in the TONE
position.
1. Restore power to the base.
2. Place the handset back on the base.
3. The status LED will blink to indicate that the
digital security code is set.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Phone
Making and Receiving Calls
The following features of the XC800 Series
phones are different depending on the handset’s
location when you make or receive a call.
Changing Channels, Flash, and
Page/Find
To change channels or access call waiting while
the phone is in use, or to use the one-way page to
locate the handset, follow these steps:
Handset On Base
Handset Off Base
Press T.
Pick up handset
(AutoTalk).
Press These Keys
You Will Hear
Answer Call
Make Call
Hang up,
A click similar to when
Press C.
1) Pick up handset.
1) Press T.
Note: Change
channels to help
Cis pressed. There
Changing
Channels
2) Press T.
3) Listen for dial tone.
4) Dial the number.
2) Listen for dial tone.
3) Dial the number.
may be a brief pause as
eliminate background your phone searches for
noise.
a clear channel.
Return handset to base
(AutoStandby).
If the call waiting tone A click, a short pause,
Press T.
FLASH
then the caller (if you
accept the waiting call. were on a call).
sounds, press Fto
1) Pick up handset.
1) Press T.
2) Press T.
3) Listen for dial tone.
2) Listen for dial tone.
The handset beeps
about 15 times.
Press page/find on the
base to locate the
handset.
Redial,
Page/Find
3) Press F.
4) Press F.
Note: Sometimes when you press T to hang up
the phone, you may get an error tone and the
phone will not disconnect. If this happens, place
the handset on the base or press T again while
holding the handset close to the base.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Your Phone
All programming functions must be completed
5. Enter the number to be dialed in tone mode.
when your phone is in the standby mode because
programming keys do not function while you are
on the phone.
3300
6. If a pause is needed during dialing to access a
long distance service, press
.
P
Storing a Number in Memory
Use these keys to store a number in memory.
P3300
Note:The P button counts as one digit.
Pressing P more than once increases the
Note: An error tone will sound and the
programming procedure will be canceled if more
than 20 seconds elapse between each keystroke
entry or step.
length of the pause between numbers.
7. Press M again.
8. Enter the memory location (0-9).
1. Remove the handset from the base.
A tone indicates that the number is stored.
2. Press M.
The talk/batt low LED blinks.
Dialing a Stored Number
To dial a number previously stored in memory,
follow these steps:
3. Enter the number you want
to store (up to 16 digits).
5551212
4. If a pause is needed during dialing to access a
1. Remove the handset from the base.
2. Press T.
long distance service, press P.
3. Press M.
4. Press the memory location number (0-9).
9P555
1212
Note:The Pbutton counts as one digit.
Chain Dialing
Pressing Pmore than once increases the
length of the pause between numbers.
On certain occasions, after dialing a number, you
may be requested by the party or service you are
calling to enter a special access code, such as
when performing a banking transaction. To do
this, follow these steps:
5. Press M again.
6. Enter the memory location (0-9).
A tone indicates that the number is stored.
1. Store the access code into one of the
memory numbers.
Storing a Mixed Number
2. Dial the main number.
If your phone is set up for pulse dialing, you can
store a mixed mode number so that you can easily
access long distance services.
3. At the appropriate time, press M followed by
the memory location number where the access
code is saved.
Use these keys to store a mixed mode number
in memory.
Note: An error tone will sound and the
programming procedure will be canceled if more
than 20 seconds elapse between each keystroke
entry or step.
Erasing a Stored Number
To erase a number previously stored in a memory
location (0-9), follow these steps:
1. Remove the handset from the base.
1. Remove handset from the base.
2. Press M twice.
3. Press the memory location number (0-9).
2. Press M.
The talk/batt low LED blinks.
3. Enter the number to be dialed in pulse mode.
Note: An error tone will sound and the erase
procedure will be canceled if more than 20 seconds
elapse between each keystroke entry or step.
555 1212
4. Press
on the handset.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your XC800 Series Cordless Telephone is not performing to your expectations, please try these simple
steps. If you are still unable to resolve the problems, contact Uniden Customer Service at (800) 297-1023,
8:00 a.m. to 5:00 p.m. Central, Monday through Friday.
Problem
Suggestion
Status light won’t come on when handset is placed in base.
• Make sure AC adapter is plugged into the base and wall outlet.
• Make sure handset is properly seated in base.
• Make sure that the charging contacts on the handset and base are clean.
• Make sure that the base antenna is fully extended and vertical.
• Move the handset and/or base to different locations and try again.
• Press the C button to select another channel.
Audio sounds weak and/or scratchy.
Can’t make or receive calls.
• Check both ends of the base telephone line cord.
• Make sure the AC adapter is plugged into the base and wall outlet.
• Disconnect the AC adapter for a few minutes, and then reconnect it.
Handset doesn’t ring or receive a page.
• Nickel-Cadmium battery pack may be weak. Charge the battery on the base for
15–20 hours.
• Extend the base antenna vertically.
• The handset may be too far away from the base.
• Place the base away from noise sources.
• The digital security code may be erased. Set the digital code.
Hear only continuous static from handset and phone will not
turn off.
• The power has been interrupted during a call.
• Restore power to the base. Make sure the phone is not plugged into an outlet
controlled by a wall switch.
• If a power failure has occurred and power will be out for some time, remove
the battery from the handset. This will prevent the battery from completely
discharging.
Specifications
General
The XC800 Series complies with FCC Parts 15 and 68.
Frequency Control PLL
Modulation
FM
Operating Temperature -10° to 50° C
Base
Receive Frequency 48.76 to 49.99 MHz
Transmit Frequency 43.72 to 46.97 MHz
Power Requirements 120 VAC 60 Hz ± 3 VAC
Size
Weight
7-1/4 in. (H) x 4-3/4 in. (W) x 2-1/2 in. (D)
Approx. 11.1 oz.
Handset
Receive Frequency 43.72 to 46.97 MHz
Transmit Frequency 48.76 to 49.99 MHz
Power Requirements Rechargeable Ni-Cd Battery Pack
Size
Weight
7-1/4 in. (H) x 2-1/4 in. (W) x 2 1/2 in. (D) (w/o antenna)
Approx. 10 oz. (including battery)
Battery (BT-801)
Capacity
Talk Mode
300 mAh, 2.4V
8 hours
Standby Mode 14 days
Specifications, features, and availability of optional accessories are all subject to change without
prior notice.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Covered under one or more of the following U.S. patents:
4,511,761
4,797,916
5,660,269
4,523,058
5,426,690
5,661,780
4,595,795
5,650,790
and other patents pending
®
©1998 Uniden America Corporation.
All rights reserved.
Printed in China.
UDZZ01518ZB
Download from Www.Somanuals.com. All Manuals Search And Download.
|