TC17A/TC21A
P/N 45067
Domestic and Std/ Export
ENGLISH/French/Spanish
Rev/ B • V1 • 1/01
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • (847)741-3300 • FAX (847)741-4406
Conveyor Toaster
Models TC17A, TC21A
OWNER'S OPERATING AND
INSTALLATION MANUAL
© 2001 Toastmaster, A Middleby Companyꢀ
is a registered trademark of Toastmaster, A Middleby Companyꢀ All rights reservedꢀ
Iꢀ DESCRIPTION AND SPECIFICATIONS
WARNING: IN CASE OF FIRE
Disconnect the toaster from its power source IM-
MEDIATELYꢀ This allows the unit to cool, making it
easier to put out the fireꢀ
Aꢀ Component Location
The major components of the toaster are shown in Figure 1
below/
Figure 1
WARNING
6ꢀ Conveyor
FOR YOUR SAFETY DO NOT STORE OR USE
GASOLINE OR OTHER FLAMMABLE VAPORS
OR LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE
5ꢀ Entry rack
4ꢀ Crumb tray
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, AL-
TERATION, SERVICE OR MAINTENANCE CAN
CAUSE PROPERTY DAMAGE, INJURY OR
DEATHꢀ READ THE INSTALLATION AND OPER-
ATING INSTRUCTIONS THOROUGHLY BEFORE
INSTALLING OR SERVICING THIS EQUIPMENTꢀ
3ꢀ Top and Bottom
temperature
control knobs
1ꢀ ON/OFF/STBY
knob
2ꢀ Conveyor speed
7ꢀ Return tray
control knob
WARNING
Do not operate the conveyor toaster on either of its
sides, on its rear surface, or without legsꢀ Prema-
ture failure of the heating elements will occurꢀ
Bꢀ Component Function (see Figure 1)
1-3/ Toaster control knobs - see Section III, Operation/
4/ Crumb tray - Collects crumbs from the toasted product/ The
WARNING
tray can be removed for cleaning/
Disconnect the toaster from its electrical power
5/ Entry rack - Loaded with the bakery product to be toasted/ The
product then slides onto the conveyor/ The entry rack can be
removed for cleaning/
supply before cleaning or servicingꢀ
CAUTION
Using any parts other than genuine Toastmaster factory parts
relieves the manufacturer of all liability/
6/ Conveyor - Transports the bakery product through the toaster,
between the top and bottom heating elements/
IMPORTANT
7/ Return tray - Collects the toasted product/ The tray can be
Contact your authorized service agent to perform maintenance
and repairs/ A service agency directory is supplied with your
toaster/
removed for cleaning/
Cꢀ Operating and Electrical Specifications
Pre-Heat Time: 15 minutes
IMPORTANT
Toastmaster (manufacturer) reserves the right to change speci-
fications and product design without notice/ Such revisions do
not entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased equipment/
Electrical Specifications/TC17 toaster models:
•
•
•
TC17A74: 120V, 50/60 Hz, 1 Ph, 1/97kW, 16/4A, NEMA 5-20P plug
TC17A63: 208V, 50/60 Hz, 1 Ph, 2/62kW, 12/6A, NEMA 6-15P plug
TC17A66: 240V, 50/60 Hz, 1 Ph, 2/62kW, 11/0A, NEMA 6-15P plug
RETAIN THIS MANUAL FOR FUTURE REFERENCE
This manual provides detailed information for the installation
and operation of your toaster/ It also contains information to
assist the operator in diagnosing problems in the event of a
malfunction/ This manual is an important tool for the operator
and should be kept readily available/
Electrical Specifications/TC21 toaster models:
•
•
TC21A63: 208V, 50/60 Hz, 1 Ph, 2/90kW, 13/9A, NEMA 6-20P plug
TC21A66: 240V, 50/60 Hz, 1 Ph, 2/90kW, 12/1A, NEMA 6-20P plug
NOTE
Electrical wiring diagrams are provided at the back of this Manual/
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Bꢀ Operation Procedure
Cꢀ Shutdown Procedure
1/ Restore electrical power to the toaster at the circuit breaker/fused
1/ Switch the ON/OFF/STBY knob to the OFF (“O”) position/
disconnect/
2/ Wait for the toaster to cool/ Note that the cooling fan will remain
2/ Switch the ON/OFF/STBY knob to the “ON” position/
in operation to allow the toaster to cool faster/
3/ Allow the toaster to pre-heat for at least 15 minutes/
3/ AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect/
4/ Adjust the toasting time (if necessary) by turning the conveyor
speed control knob/
5/ Adjust the heating element temperatures (if necessary) by turning
Dꢀ Clearing Jams
the Top and Bottom temperature adjustment knobs/
WARNING
NOTE: For proper toasting of one-sided bakery products (bagels,
NEVER INSERT YOUR HANDS INTO THE TOASTING
CHAMBER TO CLEAR A JAMꢀ SERIOUS INJURY MAY
RESULTꢀ
etc/), we recommend the following:
•
•
•
Turn the Top temperature adjustment knob to the desired
setting to toast the cut side of the product/
CAUTION
Turn the Bottom temperature adjustment knob to a lower
setting, or to the “OFF” position, as desired/
NEVER use a plastic object to clear a jamꢀ If the toaster is not
completely cool, damage to the toaster may resultꢀ
Load the product onto the entry rack with the cut side facing
CAUTION
UP, as shown in Figure 5/
When clearing a jam, use care to avoid damaging the heating ele-
If the product is loaded cut-side down, reverse the Top and Bottom
temperature knob settings provided above/ Note that if the product
is loaded cut-side down, the heat of the conveyor belt may cause
a slight streaking effect on the cut side of the bakery product/
mentsꢀ
1/ Switch the ON/OFF/STBY knob to the OFF (“O”) position/
2/ Wait for the toaster to cool/ Note that the cooling fan will remain
in operation to allow the toaster to cool faster/
5/ Load the entry rack with the bakery product to be toasted/ The
3/ AFTER the cooling fan stops, disconnect electrical power to
product will slide off the entry rack and onto the conveyor/
the toaster at the circuit breaker/fused disconnect/
6/ After toasting, remove the product from the return tray/
CAUTION - HOT SURFACES
DO NOT ATTEMPT TO CLEAR THE JAM UNTIL THE
TOASTER HAS COOLED THOROUGHLYꢀ
7/ During inactive periods, switch the Product Selection knob to the
“STBY” position/ This reduces the power to the heating elements
to save power during idle periods and extends the life of the
toaster’s components/ Switching the knob back to the “ON” position
will return the toaster to operating temperature within 5 minutes/
4/ Carefully clear the jam using a long object as a probe/ This
object should preferably be made of wood, which is less likely
to damage the heating elements/
Figure 5
Eꢀ Daily Cleaning
WARNING
WHEN CLEANING THE TOASTER, NEVER APPLY
ENOUGH LIQUID TO STAND IN PLACE ON THE UNITꢀ DO
NOT SPRAY, RINSE, OR SUBMERGE THE TOASTERꢀ
EXCESSIVE MOISTURE IN THE UNIT WILL CAUSE A SE-
VERE ELECTRICAL HAZARD AND MAY OTHERWISE
DAMAGE THE TOASTERꢀ
Load buns/bagels
CUT SIDE UP
for proper toasting
CAUTION
DO NOT clean your toaster using abrasive cleaners or padsꢀ Both
will scratch and dull the finishꢀ
1/ With the conveyor running, use a brush to clean any crumbs off
the conveyor into the crumb tray/
2/ Switch the ON/OFF/STBY knob to the OFF (“O”) position/
3/ Wait for the toaster to cool/ Note that the cooling fan will remain
in operation to allow the toaster to cool faster/
4/ AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect/
CAUTION - HOT SURFACES
DO NOT TOUCH HOT SURFACES ON THE TOASTER, OR
REACH INTO THE TOASTING CHAMBER, UNTIL THE UNIT
HAS COOLED THOROUGHLYꢀ
5/ Wipe the exterior of the toaster with a damp sponge or cloth
soaked in hot or warm detergent water/ Wipe with a clean,
damp cloth to remove the excess detergent, and then wipe again
to dry the toaster/
6/ Remove the crumb tray and the return tray from the toaster,
and empty them/ Wash the trays in warm detergent water, and
rinse them/
CAUTION
Never remove the crumb tray while the conveyor is movingꢀ
Top temperature
adjustment knob
set as desired
Bottom temperature
adjustment knob set to a
lower setting or to “OFF”
7/ Remove the entry rack from the toaster/ Wash the rack in warm
detergent water, and rinse it/
8/ Towel the trays and entry rack dry/ Reassemble all parts onto
the toaster/
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram - Model TC17A74 120V Toasters
TOP ELEMENT
BTM ELEMENT 1
BTM ELEMENT 2
MOTOR
CONVEYOR
SPEED CONTROL
“ON/OFF/STBY”
SWITCH
BOTTOM
TOP TEMPERATURE
ADJUSTMENT
SWITCH
TEMPERATURE
ADJUSTMENT
SWITCH
FAN
COOL DOWN
SWITCH
TERMINAL
BLOCK
GND
Wiring Diagram - Models TC17A/21A63 208V Toasters, Models TC17A/21A66 240V Toasters
TOP ELEMENT 1
BTM ELEMENT 1
TOP ELEMENT 2
BTM ELEMENT 2
TRANSFORMER
230V p : 115V s
MOTOR
CONVEYOR
SPEED CONTROL
“ON/OFF/STBY”
SWITCH
BOTTOM
TOP TEMPERATURE
TEMPERATURE
ADJUSTMENT
SWITCH
FAN
ADJUSTMENT
SWITCH
COOL DOWN
SWITCH
TERMINAL
BLOCK
GND
Switch Configuration - All Model TC17A and TC21A Toasters
“OFF” POSITION
“ON” POSITION
“STBY” POSITION
A Middleby Company
Toastmaster • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406
Middleby Corp 24-Hour Service Hotline 1-800-238-8444
wwwꢀmiddlebyꢀcom
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|