TDP-PX10
DATA PROJECTOR
OWNER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
Model No.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Serial No.!!!!!!!!!!
Retain this information for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
CAUTION: Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
USA ONLY
Notice:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
CANADA ONLY
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS
GIVEN IN THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner's Manual
After unpacking this product, read the
owner's manual carefully, and follow all
of the operating and other instructions.
3. Source of Light
Do not look into the lens while the lamp is
on. The strong light from the lamp may
cause damage to your eyesight.
2. Power Sources
4. Ventilation
This product should be operated only
from the type of power source which
does not exceed the voltage range
specified on the rating label and the
power cord. If you are not sure of the
type of power supply to your home,
consult your product dealer or local
power company.
Openings in the cabinet are provided for
ventilation and to ensure reliable operation
of the product and protect it from
overheating. These openings must not be
blocked or covered. Never block an
opening by placing the product on a bed,
sofa, rug or other similar surface. Do not
place it in a built-in installation such as a
bookcase or rack, unless proper ventilation
is provided.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Heat
8. Be sure that you firmly insert
The product should be situated away
the plug into the wall outlet.
Incorrect or faulty connections may result
in fire or electric shock. Avoid using an
unsound or loose outlet.
from heat sources such as radiators,
heat registers, stoves, or other
products (including amplifiers) that
produce heat.
9. Power cord protection
Power cords should be routed so that they
are not likely to be walked on or pinched
by items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and the
point where they exit from the product.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming
pool and the like.
7. Cleaning
10.Overloading
Unplug this product from the wall outlet
before cleaning. Do not use liquid
cleaners or aerosol cleaners.
Do not overload wall outlets. To reduce
the risk of electric shock, do not use the
polarized plug with an extension cord,
receptacle, or other outlet unless the
blades can be inserted completely with
three-wire grounding type to prevent
blade exposure. Failure to follow these
instructions may result in fire or electric
shock.
Always use a soft cloth for cleaning.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
11.Lightning storms
14.Do not place the product
For added protection for this product
during a storm, or when it is left
unattended and unused for long
periods of time, unplug it from the wall
outlet. This will prevent damage to the
product due to lightning and power-
line surges.
vertically
Do not use the product in the upright
position or any other vertical positions to
project the pictures. It may fall which
could result in serious injury and/or
damage to the product.
Never operate this unit on AC power
during a thunderstorm. If you see
lightning or hear thunder, never touch
the unit, cables and/or peripherals. An
electric surge caused by the storm,
may result in an electrical shock or
damage to the unit.
15.Stack Inhibited
Do not stack other equipment on this
product and do not place this product on
other equipment. The top and bottom
surface of this product increase in
temperature during normal use and may
damage the other unit.
16.Attachments
12.Object and Liquid Entry
Never push objects of any kind into
this product through openings as they
may touch dangerous voltage points
or short-out parts that could result in a
fire or electric shock. Never spill liquid
of any kind on the product.
Do not use attachments not recommended
by the product manufacturer.
Use of an incompatible attachments could
cause hazards or damage to the product.
13.Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly causing
serious injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
e) The product has been dropped or
damaged in any way (If the cabinet
should break, please handle with care to
avoid injury) .
f) The product exhibits a distinct change in
performance, which indicates a need for
service.
17.Accessories
Do not place this product on an
unstable cart, stand, tripod, bracket, or
table. The product may fall, causing
serious injury to a child or adult, and
serious damage to the product. A
product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
19.If glass components, including
lens and lamp, should break,
contact your dealer for repair
service.
This
product
incorporates
glass
components, including a lens and a lamp.
If these should break, please handle with
care to avoid injury and contact your
dealer for repair service. Avoid any
broken pieces of glass since they may
cause injury. In the unlikely event that the
lamp ruptures, thoroughly clean the area
around the projector and discard any
edible items placed in that area since
they may be contaminated.
S3125A
18.Damage Requiring Service
Unplug this product from the wall
outlet and take the product to qualified
service personnel if you encounter any
of the following conditions:
a) The power supply cord or plug is dam-
aged.
b) Liquid has been spilled, or objects
have fallen into the product.
20.Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.
c) The product has been exposed to rain
or water.
d) The product does not operate
normally when following the operating
instructions. Adjust only those controls
that are covered by the operating
instructions
since
an
improper
adjustment of other controls may
result in damage and will often require
extensive work by
a
qualified
technician to restore the product to its
normal operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
21.Replacement Parts
23.Do not leave thermal-paper
documents or easily deformed
items on top of the unit or
near the air exhaust for long
When replacement parts are required,
be sure the service technician has
used replacement parts specified by
the manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock, or other hazards.
(Only the replacement of the lamp
should be made by users.)
periods of time.
The heat from the unit could erase the
information on the thermal paper, or
cause deformation or warping.
24.Do not use the product in a
22.Safety Check
closed installation location.
Do not place the product in a box or in
any other closed installation location.
Otherwise it may overheat, which could
result in a risk of fire.
Upon completion of any service or
repairs to this product, ask the service
technician to perform safety checks to
verify that the product is in proper
operating condition.
25.Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person or a
mirror.
The laser beam may cause damage to
your eyesight.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
•
•
•
•
•
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts. If you continue to use it in that
situation, it may malfunction. Wait until the condensation naturally disappears.
In a high altitude location such as over 600m (2000ft) from sea level, the air is thin and
cooling efficiency is reduced so use the projector with [Fan mode] set to [High].
•
•
p.36
Otherwise, surface of the projector become hot and the lifetime may be reduced.
Only plug the power cord into outlets rated for use with the power cord's specified
voltage range. Do not overload extension cords or power strips as this can result in fire
or electric shock.
•
•
Route the power cable or the connecting cable away from where people could trip over
it. The projector may fall, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time, as they will leave marks on the finish. Do
not use a chemically saturated cloth.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EXEMPTION CLAUSES
•
Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous
or improper operation and other problems.
•
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or
the inability to use this unit.
•
•
Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner's Manual.
Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze function, or displaying with the varying aspect ratio of the
images, could violate the direct or indirect copyrights of the imaging software or broadcast
program, etc., if done without first consulting with the copyright holder. For this reason,
please take appropriate measures before performing one of the actions listed above,
including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
•
The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
Trademarks
•
VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.
•
•
•
DLP(Digital Light Processing) is a registered trademark of Texas Instruments, Inc.
Macintosh is a registered trademark of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
•
•
Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
All other brand and product names are trademarks or registered trademarks of their
respective companies.
Notational Conventions Used in This Manual
•
References to pages with related information are annotated as follows. For example, if
p.36
making a reference to page 36:
•
The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BATTERIES
Warning
Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or leak and may result in serious
injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and
consult a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using tissue
paper. Then dispose of the used tissue paper as flammable garbage after moistening it with
water.
Notes
•
•
•
•
•
Be sure to use AAA (LR03) size alkaline batteries.
Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects of battery disposal.
Do not mix different battery types or combine used batteries with new ones.
If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.
•
If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Before using
SAFETY PRECAUTIONS ............................................................................. 2
IMPORTANT SAFETY INSTRUCTIONS ...................................................... 4
IMPORTANT PRECAUTIONS ...................................................................... 9
EXEMPTION CLAUSES ............................................................................. 10
OTHER INFORMATION ............................................................................. 11
REMOTE CONTROL BATTERIES ............................................................. 12
CONTENTS ................................................................................................ 14
Preparations
Checking the package contents .................................................................. 16
Names of each part on the main unit .......................................................... 17
Names of each part on the control panel and remote control ..................... 18
Label locations ............................................................................................ 20
Parts on the rear panel ................................................................................ 20
Preparing and using the remote control ...................................................... 21
Operating a computer using the remote control .......................................... 23
Placement ................................................................................................... 24
Connection .................................................................................................. 26
Operations
Turning the power on and off ...................................................................... 28
Basic operations .......................................................................................... 30
Using handy features .................................................................................. 31
Using auto setting (For computer input only) .......................................................31
Correcting the keystone distortion .......................................................................31
Cutting off the picture and sound temporarily (Mute) ...........................................31
Freezing the image (Freeze) ...............................................................................32
Using the menus ......................................................................................... 33
How to use the menus .........................................................................................33
Image adjustment menu ......................................................................................34
Display setting menu ...........................................................................................35
Default setting menu ............................................................................................36
Displaying Information (Status display) ...............................................................37
Using USB Memory ..................................................................................... 38
Maintenance
About lamp .................................................................................................. 42
Lamp replacement ...................................................................................... 42
Lens and main unit cleaning ....................................................................... 45
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Indicators ..................................................................................................... 46
Before calling service personnel ................................................................. 47
Specifications .............................................................................................. 48
List of general specifications................................................................................ 48
Separately sold product....................................................................................... 48
List of supported signals (RGB signals)............................................................... 49
List of supported signals (Component signals).................................................... 50
Pin assignment of COMPUTER IN terminals ...................................................... 51
Pin assignment of S-VIDEO terminals................................................................. 51
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Checking the package contents
Please make sure that the following items are included in the box, along with the main unit.If
any item is missing, immediately contact the store where you purchased the product.
(4)
(7)
(8)
(1)
(2)
(5)
(6)
(3)
† (1) Remote control
† (5) RGB cable (3m) (See note below)
† (2) LR03 (SIZE AAA) alkaline batteries for † (6) Power cord (See note below)
remote control (2)
† (3) CD-ROM
† (7) Carrying bag
† (8) Mouse remote control receiver
† (4) Owner’s Manual (This document)
Note
•
•
The shape and number of supplied power cords vary depending on the product
destination.
To maintain original performance, always use the supplied cables.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.
‹The Supplied CD-ROM
The supplied CD-ROM contains an owner's manual, including information not available for
the printed Owner's manual (Getting Started) in Portable Document Format (PDF: ) Please
use Acrobat Reader 5 or later version to view the manual.
„ Adobe® Acrobat® Reader® or Adobe® Reader®
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF files,
please install Adobe Reader software in your computer by downloading it from the
Adobe Systems website.
„ Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader® launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner's
Manual cover and list of bookmarks appear. Click on a bookmark title to view that
section of the manual. Click on
to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader®.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the main unit
(1)
(9) (8)(7)
(6)
(5)
(4) (3)(2)(1)
(6)
(10)
(11)
(6)
(12)
(13)(14)
Back
Front
Name
:Function
p.18
(1) Infrared remote sensor
(2) Lens
:Senses commands from the remote control.
:Projects expanded image.
(3) Focus ring
:Adjusts the screen focus.
p.30
:Press to set up or stow the foot adjuster.
(4) Foot adjuster release button
(5) Air exhaust
(6) Air intake
:Expels air that has grown hot inside the projector.
:Draws in air from outside the projector for internal
cool down.
p.18
(7) Control panel
(8) Speaker
:Operates the projector.
:Outputs audio sound.
(9) Zoom ring
:Adjusts the screen size.
(10)Antitheft lock slot
:Attach a safety cable or any other antitheft device.
p.20
(11)Rear panel
(12)Lamp cover
(13)Tilt adjuster
(14)Foot adjuster
:Connects external devices.
p.42
:Remove to replace lamp.
p.30
:Adjusts the projector’s horizontal tilt.
p.30
:Adjusts the vertical projection angle.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the control panel and remote control
Control panel
Remote Control
(4)
(5)
Laser light source
Remote control transmitter
(3)
(2)
(12)
(1)
(7)
(3)
(1)
(6)
(5)
(2)
(18)
(8) (7) (6)
(4)
Battery
cover
CAUTION
(13)
(8)
(9)
•
•
Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person
or a mirror.
(14)
(15)
(16)
Caution
label
Handling and adjusting
other than described in
this manual may lead to
dangerous exposure to
laser.
(10)
(11)
(17)
Name
:Main Function
Control panel
p.28
:Turns the power on/off (standby).
(1) ON/STANDBY button
(2) Selection buttons
p.33
:Menu selections and adjustments, volume control, etc.
p.30
(3) INPUT button
(4) ENTER button
(5) MENU button
:Selects input.
:Accepts the selected mode.
p.33
:Displays menus.
p.29
(6) LAMP indicator
:Displays lamp mode.
p.29
(7) ON/STANDBY indicator
(8) TEMP indicator
:Displays whether power is on or off (standby).
p.46
:Lights when internal temperature is too high.
Remote control
p.28
(1) ON/STANDBY button
(2) Selection buttons
:Turns the power on/off (standby).
p.33
:Menu selections and adjustments, volume control, etc.
p.30
(3) INPUT button
(4) ENTER button
(5) MENU button
:Selects input.
:Accepts the selected mode.
p.33
:Displays menus.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
:Main Function
(6) LASER button
:Shows a laser pointer.
p.31
p.23
(7) AUTO SET button
(8) R-CLICK button
(9) PAGE- button
:Sets up input signal from computer.
:Functions as right-click of a mouse.
:Goes back PowerPoint® slides.
p.23
p.31
:Adjusts keystone distortion.
(10)KEYSTONE + / - button
p.21
(11)Remote control ON/OFF switch
(12)Laser indicator
:Switches the remote control On/Off.
:Lights when laser is on.
p.23
(13)Mouse control button
:Controls a mouse pointer.
:Proceeds PowerPoint® slides.
p.23
(14)PAGE+ button
(15)MUTE button
p.31
:Cuts off the picture and sound temporarily.
p.32
(16)FREEZE button
(17)VOLUME + / - button
(18)L-CLICK button
:Pauses image.
:Adjusts the volume level.
p.23
:Functions as left-click of a mouse.
Note
•
For the remainder of this manual, buttons are referred to as follows:
Selection buttons Ÿꢀ
ꢀ
ꢀ
; ENTER button Ÿ
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Label locations
Caution . use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Parts on the rear panel
(1)
(2)
(3)
(4) (5) (6) (7)
Name
:Main Function
(1) Infrared remote sensor
(2) SERVICE
:Senses commands from the remote control.
:Use for service purpose only.
(3) COMPUTER IN terminal
:Input analog RGB signal from a computer or other
source, or a component video signal (Y/PB/PR) from
video equipment.
(4) S-VIDEO terminal
(5) VIDEO terminal
(6) AUDIO IN terminal
:Input S video signals from video equipment.
:Input video signals from video equipment.
:Input audio signals.
p.38
(7) USB terminal
:Connects a commercial USB memory.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control
„ Loading dry-cell batteries into the „ Operating the remote control
Turn on the ON/OFF switch of the remote
control.
remote control
M Remove the battery cover.
Point toward the projector’s infrared
remote sensor, and press a button on
the remote control.
•
Operating the projector from the front
N Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
Approx. 15°
Approx. 5m
•
Operating the projector from the rear
Two alkaline batteries (LR03, SIZE AAA)
are used.
O Replace the battery cover.
Approx. 5m
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control (Continued)
Dry-cell batteries
•
Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
•
•
Remove batteries from remote control when not using for extended periods.
If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
•
Keep the batteries away from the reach of children. Batteries are choking hazards and
can be very dangerous if swallowed. If the batteries are swallowed, seek medical
assistance immediately.
The remote control
•
•
Turn off the ON/STANDBY switch of the remote control when not in use or to store in
baggage.
The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
•
•
•
•
•
Do not drop or bang.
Do not leave in hot or humid locations.
Do not allow it to get wet or place it on top of wet objects.
Do not take apart.
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating a computer using the remote control
A computer can be operated using the projector(s remote control. This function is available
on any computer with the Windows® 98/98SE, Windows® Me, Windows® 2000, Windows®
XP, or Windows Vista® OS, that is equipped with a USB port which can support USB1.1
(The mouse remote control receiver is also supported on OS 9 or OS X for the Macintosh).
However, please note that Toshiba does not guarantee the operation of all computers.
Connecting a computer
Connect the mouse remote control receiver (supplied) to a computer.
The remote control may fail to operate if the
mouse remote control receiver is exposed to
bright sunlight or fluorescent lighting. In such
To USB port
a case, change position or direction of the
mouse remote control receiver and retry.
Mouse remote control receiver
Operating a computer
Operate remote control(s buttons towards the mouse remote control receiver.
•
Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
•
•
•
To left click
Press the L-CLICK button.
To right click
Press the R-CLICK button.
To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
Using the computer(s page up [K] and down [L] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint® slides.
•
Remote Control Front
Remote Control Rear
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
Placement Styles
As shown in the figures below, this device can be placed in 2 different styles.
The factory setting is "floor-mounted front projection." Set the [Projection mode] in the
p.36
Default setting menu
, in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
WARNING
•
Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when
placing the unit. Attempting to clean or replace the lamp in a high location by yourself
may cause you to fall, resulting in injury.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
height (H)
(cm)
projection distance a (m)
min length max length
projection
size
(inches)
Screen
As seen from above
min length
max length
(zooming max) (zooming min) (zooming max) (zooming min)
40
60
1.6
2.3
3.1
4
1.8
2.8
8.7
12.5
16.8
21.7
32.5
41.9
52.4
65
8.8
13.1
17.3
21.9
32.9
43.9
54.8
65.8
80
3.7
90°
100
150
200
250
300
4.7
6
7.3
8
9.4
10
12
11.7
14.1
height (H)
(inch)
projection distance a (inch)
min length max length
projection
size
(inches)
As seen from the side
min length
max length
(zooming max) (zooming min) (zooming max) (zooming min)
40
60
63
71
3
5
3
5
91
110
150
190
290
370
460
560
Lens center
80
120
160
240
320
390
470
7
7
100
150
200
250
300
9
9
13
16
21
26
13
17
22
26
H
90°
1 inch=2.54 cm
a
a is the distance between the lens and the screen, and corresponds to a range of 1.6m to
14.1m (63.0 inches to 560.0 inches). H is the height from the image bottom to the center of
the lens.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Before connection
•
•
Read the owner(s manual of the device you are connecting to the projector.
Some computers cannot be used with or connected to this projector.
p.49
Check for an RGB output terminal, supported signal
, etc.
•
•
Turn off the power of both devices before connecting.
The figures below show sample connections. This does not mean that all of these
devices can or must be connected simultaneously.
Connecting with computers
Laptop type
Desktop type
To audio output
To RGB output
Audio cable
(not supplied)
RGB cable
(supplied)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with AV equipment
Audio cable
(not supplied)
Video cable
(not supplied)
Monitor cable Mini
D-sub 15 pin
(not supplied)
S-video cable
(not supplied)
To video output
To audio output
White (L)/Red (R)
To Y/C
Green (Y)/Blue
(C )/Red (C
B/CR output
To S-video
output
B
R)
Note
•
Moving pictures played back on computers using DVD software may appear unnatural
when projected with this projector. However, it is not a malfunction of the projector.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Turning the power on and off
„ Connecting the power cord
Insert the power cord connector into the AC IN
socket of the projector.
Insert the power cord plug into a wall or other
power outlet.
The TEMP, ON/STANDBY and LAMP indicator will flash,
and then ON/STANBY will only remain flashing, indicating
standby mode.
„ Removing the lens cover
Be sure to remove the lens cover when the power is turned on.
If the cover is left on the projector, it could become deformed
due to heat.
„ Turning the power on
Press the ON/STANDBY button.
The power turns on and the ON/STANDBY
indicator lights. After a moment, the start-up
screen appears.
Remote
Control
Control panel
Start-up screen
CAUTION
•
•
•
Do not look into the lens while the lamp is on. The strong light from the lamp may
cause damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a fire due to internal
overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp
cover or the bottom of the unit. Doing so could result in injury and/or damage the
object.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
•
The start-up screen will disappear after a moment. You can also configure the system to
prevent the start-up screen from appearing. To do this, use the Default setting menu
p.36
.
•
•
The first time you use the projector after purchase, the language selection menu will be
displayed.
Do not touch the lens directly with your hand. If fingerprints or stains are left on the
projection lens surface, they may interfere with the projector's ability to project images
on the screen.
„ Turning the power off
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. To
shut off the power, press the ON/STANBY button again. If you do not wish to shut off the
power, wait for a while without conducting any operations. The message will disappear
shortly. (This operation is no longer valid after the message disappears.)
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp
After cooling complete
During cooling, the ON/STANDBY and LAMP indicator flash. In this state, the power
cannot be turned back on.
However, there is no problem with unplugging the power cord in this state.
In standby mode.
Note
•
•
The projector consumes about 8W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Precaution
If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
Turn on the power.
p.28
Turn on the power by following the instructions in #Turning the power on”
.
Activate the connected device.
Turn on and start the connected device such as a computer.
Press the INPUT button.
An image of the connected equipment is projected. Each time you press the INPUT
button, it switches to the input of the connected equipment that is outputting video
signals.
Adjust the focus.
Use the focus ring to adjust the focus.
Adjust the vertical projection angle.
Use the foot adjuster to adjust the vertical position of
1
p.17
the projection image. See foot adjuster on
.
Adjust the volume.
Adjust the volume from the remote control.
Note
•
•
Lamp characteristics may rarely cause the
brightness to fluctuate slightly.
A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
2
3
•
•
The DLP® chip is made using extremely advanced technology. There may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
These are intrinsic characteristics of the technology and are not malfunctions.
p.49
Although this projector supports a wide range of RGB signals
, any signal formats
not matched to native resolution of this projector (XGA) will be expanded or shrunk,
which will affect image quality slightly. To view high-quality images, set the computer's
external output to XGA.
•
•
•
With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the computer's owner's manual.
When [Auto input search] is set to [Off] in the Default setting menu (factory setting is
[On]), the Input select menu appears if you press the INPUT button. If no signal is being
input from the connected equipment or signal input is stopped while projecting, the "No
signal" message will appear.
If a signal not supported by the projector is input, the "Unsupport signal" message will
appear.
•
•
If an unavailable operation button is pressed, the
icon will appear.
The factory setting for the OSD language is "English". Other languages can be selected
p.36
in the Default setting menu.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features
Using auto setting (For computer input only)
This function automatically sets up the projector to the optimum state. It sets
up sampling phase, frequency and screen position, for each type of the
input signal by using simple operations.
Remote Control
„ Press the AUTO SET button on the remote control.
For computer input, the
icon will appear during processing.
Note
•
•
The image may not be projected or auto adjustment/setting may not be performed
p.49
p.50
correctly for input signals other than those supported by the projector
,
/
p.34
If auto setting fails adjustment, adjust manually with Image adjustment menu
/
Remote Control
Correcting the keystone distortion
When the projector placement angle against the screen is changed while
projecting the image, the picture will undergo keystone (trapezoidal)
distortion. This projector can correct for this keystone distortion.
Before correctIon
After correction
„ Press the remote control’s KEYSTONE + / - button.
p.34
You can also select [Keystone] in the Image adjustment menu
.
Note
•
Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
Remote Control
Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be turned
off.
„ Press the remote control’s MUTE button.
The picture and sound are cut off. (The Mute function is released when
pressing the MUTE button again.)
Note
•
•
The icon
will appear while mute is in effect.
Operating any other functions will also cancel the muting.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features (continued)
Remote Control
Freezing the image (Freeze)
The projected image can be frozen. This function is used to pause video
during a presentation, etc.
„ Press the FREEZE button on the remote control.
The picture pauses. (The Freeze function is released by pressing the
FREEZE button again.)
Note
•
The
icon will appear while freeze is in effect.
•
•
Other operations will also release the freeze.
Although an image is frozen on the projector, the pictures are running on the video or
other equipment.
•
If you use this function on commercial video software, broadcast or cable-broadcasting
except for the purpose of your private viewing and listening, it may infringe the copyright
protected by the copyright laws.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
You can call up on-screen menus, and make adjustments and settings using the operation
p.18
p.19
buttons on the control panel (main unit side) and remote control
,
.
How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
1. Press the MENU button.
2. Select a Category
The Setting display menu appears.
Select a category by using
.
There are following 4 categories.
Displays the current
adjustments and settings of
the selected category.Item
shown with gray cannot be
adjusted with the current
input source.
Image adjustment menu p.34
p.35
p.36
p.37
Display setting menu
Default setting menu
Status display menu
Press the
button.
3. Adjustments & Settings
Item
Adjustment/Setting Value
Toggle items
5. End
with
key.
Press the MENU
Push
key
button
to select item.
The menu disappears.
(The menu will disappear
automatically after 30
seconds, if no operation is
conducted.)
These marks signify that
there are options.
Press
to display a
list of options.
The figure shows displays given for operation instructions purposes. As the display may
differ depending on the item, use the information in this manual as a reference.
4. Back
MENU button
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (continued)
Image adjustment menu
Use this menu to set or adjust image-related items. Items that can be set or adjusted are
marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it
indicates that you cannot select for the current input.)
Video
S-video
Item
Description
RGB
Yes
Y/PB/PR
Yes
USB
Yes
Adjust the volume.
Yes
Volume
Down
Up
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Press
. Toggle the picture mode with
.
Picture mode
Bright/Standard/True color
Correct the keystone (trapezoid) distortion of the
screen.
Keystone
Screen shrinking
at bottom
Screen shrinking
at top
Adjust the brightness of the image.
Darker Brighter
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Brightness
Contrast
Color
Adjust the image contrast.
Lower Higher
Adjust the color of the image.
Lighter Deeper
Adjust the image to an appropriate tint.
Reddish Greenish
No
No
Tint
[See note below]
Adjust the sharpness of the image.
Softer Sharper
No
Yes
Yes
Yes
No
Yes
No
No
No
No
Sharpness
H-position
V-position
Adjust the horizontal position of the image.
Move left Move right
Adjust the vertical position of the image.
No
No
Move down
Move up
Yes
Yes
No
No
No
No
No
No
Adjust with
to eliminate flicker.
Phase
Adjust with
to eliminate periodic patterns
Frequency
and flickering when many vertical lines appear
on the screen.
Note
•
[Tint] can be displayed and adjusted only when the video signal is [NTSC] or
[NTSC4.43].
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Display setting menu
Video
S-video
Item
Description
RGB Y/PB/PR
USB
Yes
No
No
No
Set to #On#, then plug in the USB memory will
enter the Slideshow mode.
Quick Start
Set to #Off#, then plug in the USB memory will
enter the File view mode.
Set slideshow mode.
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Slideshow
Interval
Auto
Manual
Adjust the interval time in Slideshow auto mode.
Short Long
Set loop function of the slideshow.
On Off
Slideshow loop
Set transition effect of the slideshow.
Display effect
[See note below]
[
[
: Enter setting mode]J[
:Selection]J
: Apply] None/Wipe/Dissolve/Cover
Screen size setting.
(Full) < >
Yes
Yes
Yes
No
Screen size
[See note below]
(Wide) < >
(Thru)
(Full): Display with 1024 x 768 resolution
(Wide): Wide-screen dispay
(Thru): Display in the native resolution
Adjust the vertical position when Screen size is Yes
set to "Wide".
Yes
Yes
No
Up/down shift
Lower
Higher
Screen to display when there is no input signal. Yes
(Logo) < > (Blue) < > (Black)
Yes
Yes
Yes
Yes
Yes
Yes
Background
Icon
Display icons as function guides.
On Off
Yes
Note
[Display effect]
None: displays screen without special effects.
Wipe: displays the next slide gradually to the right (J)over the current slide.
Dissolve: adds dissolve effect to screen.
•
•
Cover: screen overlaps previous image
If you use the Screen size setting function on commercial video software, broadcast or
cable-broadcasting programs to display images with the varying aspect ratio except for
the purpose of your private viewing and listening, it may infringe the copyright protected
by the copyright laws.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (continued)
Default setting menu
Video
S-video
Item
Description
RGB Y/PB/PR
USB
Yes
Sets projection mode in accordance with Yes
Yes
Yes
Projection mode
p.24
Placement Styles.
(Standard)
(Rear)
Select one of the languages below for the menu Yes
and messages.
Yes
Yes
Yes
Language
[
[
: Enter setting mode] J[
:Selection]J
: Apply]
English/ Français/ Español/ Português
Display start-up screen when power is turned on. Yes
Yes
Yes
Yes
Yes
Yes
Yes
Start-up screen
On
Off
Set whether the input with signals is only Yes
selected or not.
Auto input search
On
Off
Sets the cooling fan speed.
Normal High
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Fan mode
[See note below]
Sets the lamp power.
Normal Low
Lamp power
[See note below]
Sets whether to turn on the power when the ON/ Yes
STANDBY button is pressed (Manual), or when
the power is supplied (Auto).
Power on
[See note below]
Manual
Auto
Yes
Yes
Yes
Yes
Press
. (The language is not reset.)
Reset all
Resets all adjustments and settings to their
factory settings.
Yes
No
Note
•
•
Set the [Fan mode] to [High] when using the projector at the high altitude (higher than
600m or 2,000 ft.). In the mean time, the system will set the [Lamp power] to [Low]
automatically, and is not allowed to change the setting. Do not set Fan mode to [High]
when using the projector at a lower altitude.
If [Power on] is set to [Auto] and there is a power outage, the projector will come on
once power is restored.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Information (Status display)
Video
S-video
Item
Description
Input source name.
RGB Y/PB/PR
USB
Yes
Yes
Yes
No
Yes
No
Yes
No
Input
Resolution (in dots).
Color method of video signal.
Picture mode setting.
Lamp elapsed time.
Firmware version.
No
Resolution
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Video mode
Picture mode
Yes
Yes
Yes
[See note below]
Lamp time
[See note below]
Version
Note
The mode of supported RGB signals
[Version] shows the version of the projector’s internal control program. This firmware
version will be requested for customer service purposes.
p.49
•
•
!is shown.
•
Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a dealer about getting replacement for:TLPLP20 (sold separately).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using USB Memory
Connect the USB memory to the projector and select USB input
Press INPUT button to select USB source.
Plug the USB memory to the USB port.
Note
USB memory
•
•
USB HDD or hub is not supported.
If Quick Start is set to "On" and the source
other than USB memory is input, the
slideshow will automatically play back
when USB memory is plugged in. After that
if the source is switched to USB, the first slide may not be displayed or the slideshow
may be ended.
File View Mode
M When Quick Start is set to "On" and there is a JPEG file in the USB memory root folder,
p.35
the slideshow starts automatically
.
N When Quick Start is set to "Off" or there is no JPEG files in the USB memory root folder,
the file list appears as below (file view mode)."
No. of selected files/Total no. of files
Current folder
Information on the
selected file
\
001/025
1027001.JPG
Selected file
2005/06/28
793600 Bytes
1544x1024
To the upper level
folder
Folder
UI
001
002
Selected file/folder
Thumbnail display
1027001
1027002
1027003
1027004
Movie file
To next page
(See note below)
To previous page
(See note below)
1027005
1027006
1027007
1027008
Unsupported file
JPEG file
Note
•
If there are many files in the folder, it may take a long time to show all file names and
thumbnails.
•
•
2-byte characters are not supported and will be displayed as "?".
Only folders, JPEG files or supported movie files can be displayed in the file list. Other
file formats are not displayed.
•
•
Thumbnail may not be displayed due to different file formats.
If there are no files exist in the next or previous page, the arrow button
or
will
appear in red. If there are more files exist in the next or previous page, the arrow button
or will appear in white.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Slideshow Mode / Display of movie files
Slideshow Mode / Display of movie files
•
•
Quick Start
p.35
When the projector is set to the USB input and "Quick start" is set to "On"
slideshow starts with JPEG files in the root folder of the USB memory.
Start from file view mode
, the
When a JPEG file is selected and the
button is pressed in the file view mode, the
slideshow starts from the selected JPEG file. Movie files can also be played by this
operation.
Note
•
Movie file is not played in slideshow even a movie file is put in the same folder. If you
want to play back a movie file, select the file with movie icon and press the
button.
Slideshow operation
In the slideshow mode, JPEG files display on the screen fully. To change the files, select!
or . The picture displayed in the same order as displayed in the file view mode.
It takes several seconds to display the next slide. !appears when reading the next file.
The reading time varies and depends on the file size.
p.35
When "Slideshow" sets to "Auto" in the Display setting menu
, the slide changed
automatically when displaying. Display time also can be changed in "Interval" setting in the
p.35
Display setting menu
. Interval time doesn(t include reading time of the next file, so it
takes longer to display the next picture than the setting.
After showing the last JPEG picture, !will be shown in the picture. This indicates the end
of the slideshow. The slideshow ends and the projector enters in the file view!mode.
When "Slideshow loop" sets to "On", the slideshow starts from the first file again after
displaying the last file.
When JPEG file has a failure or unsupported format,
appears on the current picture and
the projector automatically starts to read the next JPEG file.
Picture transition effect is available in the slideshow. The following four modes can be
selected in "Display effect" in the default setting menu.
•
•
•
•
None: displays screen without special effects.
Wipe: displays the next slide gradually to the right (J)over the current slide.
Dissolve: adds dissolve effect to screen.
Cover: screen overlaps previous image.
Note
•
If you switch to another source during slideshow operation, the slideshow will not stop.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using USB Memory (continued)
Exit Slideshow / Stop playing movie file
Press
button to exit slideshow while the slideshow is in operation or to stop playing movie
file during movie file play back.
Note
•
•
With USB memory function, the projector may not accept any operations for a short time
after the movie file is played back. In this state, please wait for a while without
performing any operations.
There is no sound output during slideshow. When playing back the movie file, the sound
will be played back.
•
•
The sound may not be played back when playing back the movie file due to file formats.
Some movie files may not be played back smoothly due to different movie file formats.
Disconnecting USB memory
If slideshow is playing, press
key to exit sildeshow mode. Wait for a while without
conducting any operations.
USB memory can be unplugged safely after the thumbnails are displayed in the file view
mode.
About USB memory function
M The USB terminal
The USB terminal of the projector is USB 1.1 compliant, which can connect with a USB
memory.
N USB memory
•
•
•
2GB limited USB memory size.
Do not support USB HDD (Hard disk).
Do not support USB hub.
O USB memories whose operation has been verified.
TOSHIBA does not guarantee the operation of all listed USB memories.
TOSHIBA USB memory :U2E series (256MB, 512MB, 2GB)
SanDisk USB memory :SDCZ4 series (1GB, 2GB)
SanDisk USB memory :SDCZ6 series (1GB)
SanDisk USB memory :SDCZ7 series (2GB)
Note
•
This projector does not support all USB memories.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
P Backing up the data
Toshiba recommends that you back up the data saved in the USB! memory before use.
Toshiba assumes no liability for losses! incurred by data lost through the use of this
projector.
Q JPEG files
•
•
Supported file extensions are .jpg and .JPG.
Some JPEG files such as interlaced JPEG are not supported. Maximum resolution is
4096 x 2246.
R Movie files
The following are the supported Movie files and Maximum resolution.
Format
Motion JPEG
MPEG-1
Max. Resolution
352 x 288
Extension
.MOV/.mov
.AVI/.avi
640 x 480
.MPG/.mpg
•
Since many different types of movie formats exist, this projector can't play a movie file
when its format is not supported even if it has a supported extension. For detail
information about a movie format of the file, refer to user's manual of the equipment or
software that is used for making the file.
S Folders and files
•
•
•
Folders are limited to 3 levels.
The number of folders in each folder is limited to 127.
The number of files in each folder is limited to 512.
T USB memory reset
If USB memory cannot accept any operations or work incorrectly, try to reset USB
function with the following procedures:
(1)Press INPUT and MENU buttons at once.
(2)Hold down those 2 buttons for 3 seconds.
Then, the screen will become black, and file view mode screen will be displayed
if USB memory is inserted.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
•
The lamp may burst with a loud noise due to impact or deterioration, or fail to light at!the
expiration of its life.
•
How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
•
•
Burst is likely to happen if the lamp is used after the replacement period has elapsed.
When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
•
When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.
„ Immediately replace the lamp when a replacement message appears on
the screen.
•
•
•
When the replacement time approaches, a message will appear on the screen.
The risk of burst will increase if the lamp is continuously used without being replaced.
Frequently check the used hours and prepare spares when the replacement time
p.37
approaches. (Refer to "Status display"
„ When the lamp is broken
.)
•
If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area, as they may be contaminated.
If the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes or is
inhaled.
•
•
Lamp replacement
A lamp is consumable supply. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one.
WARNING
•
When replacing, always use lamp “TLPLP20” (sold separately). If the lamp other
than the specified one is used, it may cause a malfunction or damage to the unit
due to the difference in the connector shape or the lamp rate.
CAUTION
•
•
If you have been using the projector, the lamp will be very hot, and may cause
burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to broken
pieces and contact your dealer for repair service.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement (Continued)
Unplug power cord.
Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
Lamp cover
1
Remove the lamp cover.
Loosen the screw, raise the lamp! cover with your
fingers as shown to remove the lamp cover. Use
care to avoid any!damage to nails and/or tip of your
finger(s). If!you have any difficulty in removal, you
can use!a screwdriver or any other smaller tool for
your!convenience.
2
Pull out the lamp.
Remove the two locking screws and carefully set
them aside. Then pull up the handle and remove
the lamp.
Mount the new lamp.
Align the orientation, press down the new lamp
until the bottom is reached, and lock in place using
the two lamp locking screws.
Replace the lamp cover.
Align the cover and press it in. Then replace the screws you removed in step , and
tighten them until the lamp cover is no longer loose. (Be sure to replace the lamp cover.)
Reset the lamp timer.
See the lamp's manual for instructions on resetting!the lamp timer.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement (Continued)
Notes and Precautions
•
•
The [Lamp time] item in the Status display menu indicates the time of lamp use (as a
p.37
rough guide).
It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp
time]!reaches 2,000 hours, a message will appear. (After 2,000 hours, the message will
appear when the power is first turned on after each 100 hour period of use.) This!display
disappears when you press the [MENU] button.
•
Attach the lamp cover correctly so that it is not loose. If it is not attached correctly,!the
projector may fail to be powered on or the lamp may fail to come on.
Always replace the lamp with a new one.
The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
•
•
Used Lamps
This projector's lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens and main unit cleaning
„ Lens cleaning
•
Clean the lens with a commercially available blower and/or!lens
cleaner.
•
The lens is easily scratched, so do not rub it with hard objects,!or
strike it.
„ Main unit cleaning
•
Unplug the power cord before cleaning the main
unit.
•
•
Wipe dirt off the main unit gently with a soft cloth.
Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or unit failure.
•
•
Do not use benzene, thinner and the like as they
may! deform or discolor the unit or damage the
paint!surface.
Do not use a chemically saturated cloth.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Indicators
LED Indicators
TEMP LAMP
On
State/ Problems
Icon/ Messages
Close Messages
Environment overheat
Fan lock
System error
F2
F2
Lamp life time
Lamp error
USB error
The lamp life is ending. Press any key
On
p.41
Try to reset USB
or power off.
Some kinds of files
may cause this
problem, so please try
to remove the files.
F2: Flash 2Hz
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
p.46
Please see "Indicators"
as well.
.
If This Happens
Check
Is the power cord plugged in? Is it connected to the projector?
No power
•
•
p.43
Is the lamp cover open?
Is the ambient temperature high?
Is the air intake or air exhaust blocked?
Is the projector turned on? (When [Auto input search] is [Off])
Power is lost
during use
p.46
•
•
p.17
No picture
p.36
•
p.26
p.27
•
•
Are the connections set up correctly?
,
Are all the connected devices functioning properly?
p.31
Is the mute function on?
•
•
p.34
Is the brightness setting minimized?
No audio
p.26
p.27
•
•
Are the connections set up correctly?
,
Are all the connected devices functioning properly?
p.31
•
•
Is the mute function on?
Is the volume setting minimized?
Is the input signal supported by the projector?
p.34
Picture not
displayed
correctly
p.49
p.50
•
•
,
Is something generating an abnormal video signal, for instance the video
tape?
Picture blurred
Part of picture
out of focus
p.45
•
•
•
•
•
Is the lens dirty?
Is the lens focus adjusted optimally?
Is the projection distance within the projector's supported range?
p.30
p.25
p.25
p.34
Is the projector's screen placement angle tilted too far?
Are the sharpness or sampling phase adjustments off?
Colors too light
Bad shading
p.34
Are the color or tint adjustments off?
•
•
•
p.45
Is the screen dirty?
Is the lamp nearing the end of its service life?
Are the brightness or contrast adjustments off?
p.44
Image is dark
p.34
p.44
•
•
Is the lamp nearing the end of its service life?
Remote control
doesn’t work
p.18
•
•
Is the remote control ON/OFF switch set off?
Are the remote control's batteries exhausted?
p.21
p.21
•
Are the batteries inserted into the remote control correctly?
•
Is the remote control being used within the effective range?
•
•
Are there any obstructions between the remote control and projector?
Are there any fluorescent or other bright lights shining at the projector's
infrared remote sensor?
USB memory
images aren't
projected
•
Is the USB memory inserted correctly?
p.40
Is a USB memory not supported by the projector inserted?
Are there any JPEG or movie files saved on the USB memory?
Are the files too large or in an unsupported format for the projector?
•
•
•
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
„ List of general specifications
Item
Specification
Consumption Power
Weight
230W
1.3kg
External Dimensions
210 x 76 x 170 (W x H x D, mm)
(including protruding parts)
Cabinet material
Temperature
Mg Alloy
Operating temp:
5oCto35oC(41oFto95oF)foraltitude:0m-1200m(0-4000ft)
5oCto30oC(41oFto86oF)foraltitude:1200m-3000m(4000-10000ft)
Storage temp: -20oC to 60oC (-4oF to 140oF)
Relative humidity
Altitude
80% max.
Operating: 0 - 3000m (0 - 10,000 ft)
Storage: 0-12,000m (0 - 40,000 ft)
1 DLP® chip
Display device
Picture elements
Lens
True 1024 x 768 resolution, 16.7M True colors
f=22-25.5mm
Light source
High-pressure mercury lamp (180 W)
Projection screen size
Projection distance
Speaker
40-300 inches
1.6-12 m
2W
COMPUTER (Y/PB/PR)
IN terminal
Mini D sub 15 pin Analog RGB / Y/PB/PR (dual use)
VIDEO: RCA Pin Jack
AUDIO 3.5mm dia. stereo mini-jack
S-VIDEO
VIDEO terminal
USB terminal
USB type A (for USB memory)
USB type B (for service only)
Note
•
•
•
This model complies with the above specifications.
Designs and specifications are subject to change without notice.
This model may not be compatible with features and/or specifications that may be added
in the future.
„ Separately sold product
Replacement Lamp: Model TLPLP20.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
„ List of supported signals (RGB signals)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Compatibility
Resolution
H-Sync [KHz]
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
64.0
67.5
60.0
75.0
64.0
47.8
60.3
68.6
49.7
62.8
V-Sync [Hz]
59.9
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
60.0
75.0
75.0
85.0
70.0
75.0
60.0
75.0
60.0
60.0
74.9
84.8
59.8
74.9
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
SXGA
1152 x 864
1280 x 960
1280 x 1024
1280 x 768
WXGA
1280 x 800
Note
•
Signals whose resolution exceeds the native resolution (1024 x 768 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
„ List of supported signals (Component signals)
Signal
480i
Horizontal Frequency (kHz)
15.8 kHz
Vertical Frequency (Hz)
60 Hz
60 Hz
50 Hz
50 Hz
60 Hz
50 Hz
60 Hz
50 Hz
480p
576i
31.5 kHz
15.6 kHz
576p
720p
720p
1080i
1080i
31.3 kHz
45.0 kHz
37.5 kHz
33.8 kHz
28.1 kHz
50
Download from Www.Somanuals.com. All Manuals Search And Download.
„ Pin assignment of COMPUTER IN terminals
Pin No.
Signal Name
RED
1
2
3
4
5
GREEN
BLUE
NC
GND
6
GND
Mini D-sub 15 pin connector
7
GND
8
GND
9
VCC 5V
NC
10
11
12
13
14
15
NC
SDA
HSYNC
VSYNC
SCL
„ Pin assignment of S-VIDEO terminals
Pin No.
Signal Name
GND
1
2
3
4
GND
SVID_LUM
SVID_CHR
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|