THB Bury Automobile Accessories LT 9100 User Manual

TWIN-PHONE FOR UNI System 8

LT 9100

Operating manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Introductory information

cabin or in airbag deployment zones. Please adjust the device’s volume

so that you can still hear outside noises.

1. General

Dear customer,

Use while driving

Only use the Twin-Phone in situations where the traffic allows such use

and you do not injure, hinder or disturb other motorists or put them at

risk.

You have purchased a Bury connecting unit and therefore chosen a

product of high quality as well as absolute ease of use. Bury’s purchase,

production and service are subject to strict quality management accor-

ding to DIN EN ISO 9001. The “LT 9100” connecting unit (hereinafter

referred to as Twin-Phone) corresponds to the CE and e1 safety stan-

dards.

Intended use

Damages caused by improper use of the connecting unit or the hands-

free car kit may result in loss of warranty. For this reason, please read

the user’s guide carefully. The device must always be protected from

moisture, extreme temperatures or shock.

Please read the user’s guide carefully in order to familiarise yourself

with the connecting unit and therefore enjoy using it for a long time.

Please also read all notes and retain for reference in your vehicle.

Faults

Do not switch the device on if you have noticed and/or suspect faults.

Please visit a Bury specialist dealer or contact the Bury hotline. Impro-

per repairs may put you at risk. Therefore only qualified personnel must

inspect the device.

If you have further questions on installation and use, please contact

your specialist dealer. They will be happy to give proper advice and

forward your experience and suggestions to the Bury team. You may

also contact our hotline. Please find all telephone and fax numbers

under the Service section.

3. Included in delivery

Have a pleasant journey!

The following components are included in your package:

Your Bury team

1. Twin-Phone

2. Steering wheel remote control

2. Notes on safety

Installation – who and where

You can easily insert the Twin-Phone in the hang-up cup of a Bury

hands-free car kit (base unit from the UNI System 8) at any time. The

hands-free car kit, however, should always be installed by a specialist

dealer.

Power supply

This device to be used in connection with a Bury hands-free car kit has

been designed for use in vehicles with an onboard supply system of 12

Volts (cars). Always contact your Bury specialist dealer or seek informa-

tion through our telephone hotline if you are planning to install the

device in a vehicle with 24V onboard system (lorries).

Position, volume

Install the hang-up cup (of the base unit) of the Bury hands-free car kit

in the vehicle so that it does not obstruct your view and that the com-

ponents are not located in passenger impact areas within the vehicle

Download from Www.Somanuals.com. All Manuals Search And Download.

Device description and installation

4. Description of the Twin-Phone

will switch to standby mode, in order to reduce power consumption. All

available functions can be used via the Twin-Phone until you disable

external SIM access.

The HF profile (hands-free profile) provides a second connection opti-

on. Here, connections are established via your mobile’s GSM network.

The mobile phone can be used as usual.

The SIM card slot

The SIM card slot inside the Twin-Phone is the component in which the

SIM card is inserted. Through this, the Twin-Phone can read the data

stored on your SIM card (e.g. phonebook entries).

Display

You can insert the SIM card into the back of the Twin-Phone. In order

to do so, remove the device from the hang-up cup.

1. Open the sliding element on the back of the Twin-Phone in a

downward movement as indicated by the arrow.

2. Open the black flap. The flap will flip open by pressing the

small vertical, rectangular button – marked with PUSH OPEN.

3. Now, you can insert a SIM and/or a TWIN card into the inside

of the flap. Please make sure that the topside of the SIM card

(with the memory chip) is facing upwards when inserting it in

the flap. It must be on the visible side. The SIM card edge

with the bevelled corner must face upwards.

Telematic key (info number) for

speed dialling

Telematic key (service number) for

speed dialling

4. Close the flap. Press the Push mark on the flap. The flap will

snap and close.

5. Push the sliding element back until it locks. The local SIM card

is now ready for use. Place the device back in the hang-up

cup.

The Twin-Phone

The Twin-Phone is a high quality connecting unit for a Bury hands-free car kit (a base unit from the UNI

System 8). The large high-contrast display shows all menu and telephone functions (depending on

mobile model).

You can also insert a SIM card in the Twin-Phone in order to use it as an independent phone (only in-

side the vehicle).

The Twin-Phone also allows you to connect a mobile phone via the Bluetooth interface. For this, you

can use different profiles (transmission protocols, HFP and SAP).

If you connect the Twin-Phone to a mobile phone using the SAP profile (SIM Access profile), the inte-

grated GSM module will access the SIM card in your mobile. This will render the mobile inactive, i.e. it

Download from Www.Somanuals.com. All Manuals Search And Download.

Device description and installation

general, never leave the Twin-Phone in the vehicle. This is the best

protection against theft. In order to do so, press the button on the right

side (looking at the phone from above) of your hands-free car kit’s

hang-up cup to release the lock.

5. Installation of the Twin-Phone

Installation Overview e.g. with UNI CarTalk

If the phone is exposed to direct sunlight while the car is parked, the

inside of the cabin may heat to temperatures exceeding 70°C. For this

reason, remove the Twin-Phone from the hang-up cup and vehicle as

you may otherwise encounter disruptions for a short while once the

Twin-Phone has been switched back on.

7. Steering wheel remote control

You can control the system and enter data via the illuminated steering

wheel remote control (hereinafter referred to as SWRC). The SWRC is

housed in part A of the SWRC is low after being used for a long time,

simply replace it with a new, suitable battery.

Place the Twin-Phone in the hang-up cup of the Bury hands-free car kit

in order to enable power supply to reach the device. If such supply is

continuous, the device will immediately switch on. If not, the system

will be activated upon ignition and/or starting the engine.

Part (A)

As a default, the Twin-Phone screensaver will be displayed, which also

shows the time and date. In order to ensure that these functions are

continuously provided in case of an interruption to the power supply

(e.g. when removing the Twin-Phone from the hang-up cup), the Twin-

Phone uses an integrated re-chargeable battery. When the car is swit-

ched off (Twin-Phone remains in hang-up cup), the power supply will be

maintained – time and date are still displayed. It is not necessary to

remove the battery as it re-charges automatically once the Twin-Phone

is supplied with onboard power.

In case of an interruption to the power supply (removal from the hang-

up cup), the battery will ensure the time and date are displayed for a

period of approx. 3 to 4 weeks. In case of longer periods of interrupti-

on, the time and date must be reset.

7.1 Fitting the steering wheel remote control

First, disconnect the parts (A) and (B). Loosen the clamping device of

part (B) as illustrated in the picture. Now place the clamping device on

the steering wheel and re-attach it to part (B). Reassemble the two

parts. The SWRC is now fitted.

6. Switching off and removing the phone

If you leave your car for a short while, you can set the Turn-off time

function (Setup, System settings, Turn-off time) so that the Twin-

Phone will automatically switch off after a certain period of time. See

the chapter on the respective menu for detailed information.

If you leave your car for longer periods or over night, you should, in

Download from Www.Somanuals.com. All Manuals Search And Download.

Device description and installation

Pairing the steering wheel remote control

The Twin-Phone is normally paired to the supplied SWRC when it leaves

the factory. This means that both devices each detect the identifier si-

gnal of the other device. If this is not the case, pair the devices as fol-

lows with enabled ignition:

OK key

Confirming a selection (if such was not entered via the number keys).

On the SWRC, press the ESC and the information key at the same time

(keys 3 and 7), see picture 8. Then place the Twin-Phone in the hang-

up cup of your HFCK. The display will now show ‘BURY TECHNOLO-

GIES’, i.e. the initialising process is now running. Once the initialisation

has been successfully completed, the screen saver is displayed.

Scroll keys

In the menu: scroll function, from above downwards and from left to

right.

Now release keys 3 and 7 of the SWRC and press the shift key to open

the main menu of the Twin-Phone. If this is not possible, the device and

the SWRC have not been paired correctly. Please repeat the pairing

procedure as described above.

Number keys

Enter numbers and write SMS.

Volume control

In standby mode: press this key once for setting the Ring tone volu-

me, twice for setting the Voice-tag volume, three times for setting

the Talk volume. Turn the control upwards and/or downwards to turn

up and/or down the volume.

7.2 Key functions

When calling: press key once for setting the Talk volume, twice for

setting the Ring tone volume, three times for setting the Voice-tag

volume.

Call answering key

For answering incoming calls.

In standby mode: press key once to access the submenu last Dialled

numbers. You can activate the voice-dial function by pressing and

holding this key.

7.3 Creating contacts and SMS

In the menu: confirm new entries created using the number keys.

You can save entries in the internal and external phone book as

well as Write SMS using the number keys of the SWRC. The keys 2 to

9 also display letters, which can be entered by pressing the required

key. The first letter (from left to right) can be entered by pressing the

respective key once, the second one by quickly pressing the key twice

and so on.

Call termination key

Reject incoming calls or end a call.

In the menu: press key to confirm after selecting a function by highligh-

ting the respective item with OK key.

In the left bottom corner of the display, the icon for the number keys of

the SWRC is displayed when creating phone book entries or writing an

SMS, i.e. the number keys are enabled and you can enter the required

letters.

Shift key

Accessing the main menu while the screen saver is activated.

In the individual submenus: access to options such as Clear list in the

Dialled numbers submenu.

Phonebook entries or SMS: shift between scroll keys and number

keys.

The call termination key can be used for deleting an entered letter

and/or text. The respective last letter to the left of the cursor will then

be deleted. If you want to delete or insert a letter located elsewhere,

press the shift key in order to enable the scroll keys (the icon in the left

bottom corner will now show the arrows indicating the four possible

directions instead of the number keys). You can now position the cursor

anywhere in the entered name and/or the SMS text using the scroll

In standby mode: enabling and disabling the silent function by holding

this key.

Download from Www.Somanuals.com. All Manuals Search And Download.

The first steps

keys 2, 4, 6 and 8.

8. First use

If you want to enter another letter after having shifted the cursor, press

the shift key in order to enable the number keys again. The icon in the

left bottom corner will now show the number keys.

When the device is switched on, the illuminated display will first show

‘BURY TECHNOLOGIES’ and then read Waiting for SIM card activa-

tion. You may also have to enter your PIN. If no SIM card was inserted,

the display will read SIM card missing for a moment until the screen

saver is activated. Press the shift key in order to access the main

At the bottom of the display (centre), you can see whether capital let-

ters (ABC) or lower case (Abc and/or abc) is enabled. If ‘Abc’ is display-

ed, the first word of each sentence will begin with a capital letter. The

other letters and words will automatically be displayed in lower case. If

you only want to use capital letters, press the hash key once or press

this key twice for lower case.

The screen saver comprises the following information: in the top left

corner the icon for the SIM card is shown - when Default is set (re-

gardless whether a SIM card was inserted or not). In the top right

corner, the symbol for the antenna is displayed, with two to three hori-

zontal bars showing the quality of reception. In the middle of the dis-

play, the time and date is displayed.

In the right bottom corner and above the line, the number of characters

already entered is displayed, and below the line, how many characters

you may still type in. When entering names in the internal or exter-

nal phone book, you may enter up to 50 characters. When writing an

SMS, you may use a maximum of 160 characters.

The display will remain illuminated for approx. 60 seconds. After this

time, the light will switch off if you do not use the phone, and the pho-

ne will automatically switch to standby mode.

Space characters can be entered by pressing the 0 key. If you press the

0 key repeatedly 2 to 17 times, you can enter one of the following cha-

racters in the order given: 0 % ( ) + - * / ^ = < > [ ] { }.

By default, the device is set so that users are able to use the phone

immediately for calls once the SIM card is inserted into the Twin-Phone.

This means that the SIM card BT profile is already activated. Please

refer to the chapter BT profile for information on the operating profile

of SIM card as well as the SAP, HFP and Auto profiles.

Dots can be entered by pressing the 1 key. You can also enter the fol-

lowing (punctuation marks) characters in the order given by pressing

this key repeatedly: . , ! ? 1 ’ : ; - / “ _ .

In order to be able to make calls when in other profiles, select the re-

quired profile in the BT profile submenu. Then select the item BT

connections to pair your mobile phone with the Twin-Phone from the-

re. Please refer to the chapters following the section “The first steps”

for more detailed information.

For entering the special characters & @ # € £ $ ¥ xx ~ § \ | ¡ ¿, press

the star key once and/or 2 to 14 times repeatedly.

9. Making a call

When the Twin-Phone is switched on, e.g. with inserted SIM card, you

can make a call by entering the phone number using the number keys

and then establish a connection by pressing the call answering key.

Or simply press the call answering key once when the screen saver is

shown in order to open the list of the last Dialled numbers. If you

now press the call answering key once, a connection is established to

phone the last dialled number. When the phone is used for the first

time, the Call registers are empty.

In all BT profiles, you also have the option to establish a connection

Download from Www.Somanuals.com. All Manuals Search And Download.

The first steps

Menu navigation

via the menu to a phone whose number is stored in the internal pho-

ne book of the Twin-Phone.

11. Main menu

In order to open the main menu when the screen saver is active, always

press the SWRC shift key.

In the SIM card profile or SAP profile, you can also establish a con-

nection to the phone whose number is stored in the external phone

book. In the external phone book, only entries stored on your SIM

card can be used.

In the main menu, the display will show six menu items: Phone book,

Call registers, SMS, BT connections, BT profiles, Setup, which

you can access using the SWRC scroll keys 2, 4, 6 and 8.

Or simply enable the voice-dial function by pressing and holding the call

answering key. You are then prompted to say a record (only possible if

a record was previously stored in the internal phone book).

In order to quit a menu, press either the call answering key, the call

termination key or the OK key depending on the submenu structure.

10. Answering a call

Please note that not every menu in every profile may be active. Please

refer to the chapter BT profile for more details.

If your phone shows an incoming call, a symbolised telephone receiver

icon will be displayed on the Twin-Phone. When the SIM card was inser-

ted or if in SAP profile, only the ring tone set for the Twin-Phone will

sound; the same applies to SMS. In the HF profile, the ring tone of

both the Twin-Phone and the mobile phone will sound in case of an in-

coming call.

12. Bluetooth profiles

In the BT profile menu’s submenu, you can choose from four opera-

ting profiles, which represent different ways of establishing a connec-

tion to your mobile phone. You can access the submenu by pressing the

OK key. Then, the SIM card, SAP, Hands-free and Auto profiles

are displayed.

If there is an entry for the respective caller in the internal or external

phone book, the saved name will be displayed (in HF profile, no

entry will be displayed if stored in the external phone book).

Find the required operating mode using the scroll keys 2 and 8 and then

select it by pressing the OK key. Confirm the selected profile by pres-

sing the call termination key. The enabled operating profile will then be

displayed in the top left corner on the screen saver.

Answer the call by pressing the call answering key; press the call termi-

nation key to end or reject a call.

The number of missed calls will be displayed in the top right corner.

Details on the missed calls are shown in the main menu Call registers,

Missed calls.

The last active profile, for example the symbol for the SAP profile, will

flash in the top left corner of the display after the phone was switched

on. If you do not change the SAP profile, the Twin-Phone will, each

time it is restarted, automatically attempt to establish a connection to

the mobile phone it last communicated with.

The same applies to received SMS. These will be indicated by a small

icon in the form of a closed envelope. To read the message, select the

main menu SMS and then Inbox.

If you wish to change the profile, press the shift key, open the menu BT

profiles, choose the required profile and confirm with the call termina-

tion key. When a new BT profile is selected, no automatic connection

between the Twin-Phone and the mobile phone will be established. This

must be established via the menu BT connections. You may skip to

this chapter now if you want to read the descriptions of the individual

BT profiles at a later time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

12.1 SIM card profile

Furthermore, the antenna symbol is displayed in the top right corner of

the screen saver screen when in SIM card profile. The antenna sym-

bol, including the bars for reception quality, is displayed even if no SIM

card is inserted in the Twin-Phone. The antenna symbol indicates an

unknown, available network (to be used in emergencies).

Choose this profile if you want to use a SIM card with the Twin-Phone.

In this case, pairing or the current BT connection to the mobile phone

is not required. The Twin-Phone – with inserted SIM card – can be

turned into an independent car phone when used in conjunction with a

UNI System 8 hands-free car kit.

Note:

You can call the emergency number (e. g. 112 in Germa-

ny or 999 in Great Britain) directly from the Twin-Phone

without inserting a SIM card. (The easiest way to do this is

to use the Twin-Phone telematic keys, see chapter Setup,

System settings, Telematic keys).

You may also use a TWIN card in your Twin-Phone. The TWIN card is

linked to your SIM card, therefore the telephone number is identical.

Calls or SMS will be transmitted by the respective active card. Conse-

quently, it is no longer necessary to swap the SIM card.

If you have selected the SIM card profile, you may be required to

enter your PIN. The PIN is your Personal Identification Number and is

normally provided with the SIM card. If you have set your mobile to

request the PIN every time the phone is switched on, you must also

enter this PIN in the Twin-Phone. In all other cases, you will not be re-

quested to enter your PIN.

When a SIM card is inserted, the following items are enabled in the

Twin-Phone main menu: Phone book, Call registers, Messages, BT

profiles and Setup. Since connection to the mobile is not required,

the menu item BT connections is not available.

12.2 SAP profile

After you have entered the 4- to 8-digit PIN, confirm this using the call

answering key. If you have accidentally entered a wrong digit, you may

delete this by pressing the call termination key, then correct it by re-

entering the digit using the number keys and confirm using the call

answering key. If the correct PIN is entered, the screen saver will be

displayed. In case that an incorrect PIN is entered, an error message

will be displayed and you will be prompted to re-enter the PIN.

The SIM access profile allows the integrated GSM module to exter-

nally access the SIM card in your mobile. This means that the Twin-

Phone is able to retrieve the SIM data via the SAP profile. Your mobi-

le must support the SAP (SIM Access profile) technology if you want to

use this option.

In this profile, your mobile is put in on standby to reduce the electrical

discharge of the mobile battery to a minimum while the connection is

maintained.

Note:

Please note that your PIN will be locked for security re-

asons if an incorrect PIN is entered three times consecu-

tively. You will require your PUK code (Personal Unblocking

Key) to unlock the SIM card; this code is also supplied with

the SIM card. If an incorrect PUK code is entered ten times

consecutively, your SIM card will be completely blocked. The

display will then read ‘SIM card locked’. In this case, please

contact your network operator for assistance in providing

either a copy of your current SIM card or a new card.

If you have selected the SAP profile, you may need to enter your PIN.

If you have set your mobile to request the PIN every time the phone is

switched on, you must also enter this PIN in the Twin-Phone.

In case of incoming calls, only the ring tone of the Twin-Phone will

sound. Missed calls as well as the name of your network operator will

now be displayed on the Twin-Phone. The same applies to receiving

and sending an SMS. No entries can be made in the mobile as long as

the activated SAP connection is maintained.

In the SIM card profile, the SIM card symbol is displayed in the top

left corner of the screen saver. In the top middle, a small house-like

icon is displayed as symbol for your home network. If a pyramid is

displayed instead of the house symbol, the telephone is operating in a

different available network.

Due to the transmission of SIM card data, it may take up to 60 seconds

before the SMS submenu can be accessed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

12.3 Hands-free profile

If only one person uses the Twin-Phone, they choose their preferred

profile (SIM card, SAP profile or HF profile), which will be enabled

every time the phone is switched on (unless the profile has been chan-

ged). In the future, this will allow a connection to be automatically es-

tablished between the Twin-Phone and the mobile once the devices

have been paired.

Yet another operating option is the hands-free profile (HF profile) in

the BT profiles menu.

Note:

Please note that, with the selection of the HF profile,

using the BT technology will increase the battery discharge

rate of your mobile and therefore reduce the number of

operating hours.

13. Bluetooth connections

In the HF profile, the connection is established via the GSM network

of your mobile. The name of your network operator will, however, only

be displayed on the mobile.

You can access the menu BT connections in the main menu by pres-

sing the OK key. This submenu is required for pairing or connecting

your mobile with and/or to the Twin-Phone. Here, pairing means to

establish the very first connection through identification. The BT con-

nections menu comprises four submenus: Establish BT connection,

Paired devices, Disconnect BT and Bluetooth setup.

Incoming calls are displayed on the Twin-Phone. The mobile phone ring

tones and the Twin-Phone will also sound. The same applies to inco-

ming SMS.

If you use your SIM card with the Twin-Phone, you will not need the

functions available in the BT connections menu. This function will not

be available when the SIM card is inserted.

Apart from the SMS function, all other main menu functions are availab-

le when the HF profile is selected. When using the phone book, you

can only access the internal phone book. The external phone

book function is not available.

Note:

For security reasons, it is not possible to pair your mo-

bile phone with and/or establish a new connection to the

Twin-Phone via your mobile’s menu. This is the only way to

ensure that no other user within the same reception zone,

e.g. a passenger in certain traffic conditions (traffic jam),

can connect their mobile to your Twin-Phone.

The HF profile also provides the option to disconnect any connection

between the Twin-Phone and mobile via the menu of your mobile pho-

ne.

12.4 Auto profile

In the auto profile, the Twin-Phone independently selects a profile.

The Twin-Phone will search for options to establish a connection in the

following order: first, it will check whether a SIM card has been inserted

in the integrated card slot. Then, it will search for an option to establish

a connection using the SAP technology. Finally, it will check whether it

is possible to establish a connection in the HF profile.

13.1 Establishing a BT connection in HF profile

The submenu Establish BT connection indicates whether a BT con-

nection to a mobile was established. The BT connections menu will

only be enabled if you have activated the HF profile or SAP profile

via the Twin-Phone menu BT profiles.

If a SIM card is inserted in the Twin-Phone, the auto profile will auto-

Pairing

matically open the SIM card profile and will stop searching.

Use this submenu for pairing the phone with another BT device. This

means that both devices will detect the respective identifier signal of its

respective counterpart to automatically establish a connection in the

future.

a) Select Establish BT connection in order to pair the Twin-Phone

with your mobile.

It is advisable to select the auto profile if, for example, a user with an

SAP-compatible mobile and another with an HFP-compatible mobile use

the Twin-Phone in turn. The pre-selected auto profile will automati-

cally enable the suitable profile after the phone is switched on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

b) For this, the Bluetooth interface of your mobile must be enabled and

your mobile’s name displayed. The display will show Establish BT

connection - Searching.

the icon of the selected profile will continue to flash on the screen saver

until you have manually chosen a mobile name in the Paired devices

submenu to establish a current connection to the mentioned mobile.

c) Press the OK key to start Searching, i.e. Search BT devices. If the

search process is successful, the name of the detected phone is dis-

played.

Current connection

If you want to establish a connection to a previously paired mobile,

select Paired devices (13.3) in the BT connections main menu.

Note:

If the mobile name is hidden, the Twin-Phone will not be

able to establish a connection. You can either keep the de-

fault mobile name or choose a name. It is recommended

to allocate individual mobile names as it will otherwise be

difficult to distinguish between them if, for example, two

mobiles of the same make are paired with the Twin-Phone.

The phone can be paired with up to ten different mobile

phones. All paired mobile phones are entered by name in

the Paired devices submenu.

A current connection can only be established for one mo-

bile at a time.

If the Twin-Phone display does not show the intended mobile name,

repeat the search process. Select Search again with the OK key.

13.2 Establishing a BT connection in SAP profile

If you have enabled the SAP profile in the Twin-Phone BT profiles

menu, the subsequent pairing process is almost identically. The only

difference: when using the Bluetooth SAP profile, a 16-digit BT code is

provided. This must be entered in the mobile to allow pairing. For each

pairing process in SAP profile, a new 16-digit code is generated which

must, in turn, be entered into the mobile. The two devices will then be

paired.

d) After confirming the detected and displayed mobile name using the

OK key, the devices are paired. Simultaneously, a 4-digit BT code will be

displayed in the bottom of the display. Enter this BT code in your mobi-

le. A different 4-digit code will be provided every time two devices have

been newly paired in HF profile.

e) Before entering the BT code in your mobile, you may need to confirm

on your mobile that you accept your phone to be paired with the Twin-

Phone. In your mobile’s menu, you can select whether you want to be

requested to confirm acceptance each time before a BT connection to

an external device is established.

After successful pairing, you may need to accept that the Twin-Phone

externally uses the SIM card data of your mobile. If applicable, the

prompt Enter PIN code will be displayed after a completed pairing

process in SAP profile. No prompt requesting you to enter the PIN will

be displayed, unless this is enabled on your mobile.

You have approx. 30 seconds to enter the code. If you do not enter the

code within this time limit, the process will be aborted. Initiate another

connection process by selecting the detected mobile’s name on the

Twin-Phone with the OK key.

If the devices were not paired after repeated attempts, delete all pre-

vious pairings with BT devices listed in the menu of your mobile (also

the pairing with the Twin-Phone) and repeat the pairing process.

13.3 Paired devices

The Paired devices submenu will show whether and with which mo-

bile phone your Twin-Phone has been paired. In the bottom of the dis-

play, you will see a 12-digit combination consisting of digits and letters

for each selected mobile. This is the respective Bluetooth address of

the paired mobile. It is used for distinguishing purposes in the event

that two mobiles of the same make with identical device names are

paired with the Twin-Phone.

f) If pairing is successful, the menu BT connections, Paired devices

will now include the name of your mobile while the Twin-Phone will al-

ways attempt to establish a connection to the paired phone. In order to

ensure this, the previously enabled profile must not be changed.

If the Twin-Phone is unable to establish a connection to your mobile,

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

Establish current connection

In HF profile, you can also disconnect via the menu of your mobile.

If you confirm one of the displayed mobile names with the OK key, you

have two options: you may now establish a current connection to the

paired phone or delete the pairing.

Please note that any active connection will be interrupted as soon as

you, and therefore your phone, leave the transmission range of the

Twin-Phone. Radio transmission will still be maintained in a radius of up

to 10 metres between the Twin-Phone and the mobile.

If you want to establish a connection to the paired mobile, select the

required phone name and then confirm this with the OK key.

If the Twin-Phone is unable to establish a connection, make sure that

the Bluetooth interface of your mobile was enabled and that your

mobile’s name is displayed. In the Twin-Phone, either the HF profile or

the SAP profile must be enabled.

13.5 BT setup

The Bluetooth setup submenu includes the Local BT name func-

tion. If you press the OK key once again, the Local BT name

(LOOKnTALK) as listed in Default will be displayed. The cursor is

active while the local name is displayed and you can now independent-

ly change the Local BT name. Once entered, press the call answering

key in order to set the new name.

Delete pairing

In order to delete a pairing, select the respective mobile, which is to be

disconnected from the Twin-Phone. Press the OK key to confirm the

Delete pairing prompt.

You can quit this menu function by pressing the call answering key if

The concerned mobile name is then no longer listed in the Paired de-

vices submenu. If only one pairing has previously been realised, this

submenu will be empty after deleting this paired device.

you choose to maintain the Local BT name given in Default.

13.4 Disconnecting BT connections

If there is a current connection in HF or SAP profile to a mobile pho-

ne, you can open this submenu by pressing the OK key. The prompt

Disconnect BT – Are you sure you want to disconnect BT will

then be displayed. Press OK to confirm. Press the call termination key

twice to return to the main menu if you want to maintain the BT con-

nection.

If you want to disconnect the BT connection in SAP profile, repeat the

above steps. After disconnecting, your mobile will be active again (no

longer in sleep mode) and can be used immediately. On the Twin-Phone

screen saver, the prompt Deregister will be displayed just above the

indicated time. The display will then show No phone connected.

You have several options to disconnect an active connection. The easi-

est way to do this is to interrupt the power supply by removing the

Twin-Phone from the hang-up cup.

You may also disconnect via the menu (BT connections, Disconnect

BT).

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

once to access further information.

14. Phone book

If you then press the call answering key, a telephone connection to the

phone of this particular party will be established.

When you open the phone book in the main menu by pressing OK,

you may choose between two phone books. The internal phone

book of the Twin-Phone holds up to 500 individually saved entries of

which 45 can be used with the voice-dial function. The external pho-

ne book can also contain up to 500 contacts stored on your SIM

card.

Phone book contact options

You can also open a submenu with five functions for this particular

phone book contact by pressing the OK key or the shift key, before the

information on this contact is displayed (name and phone number).

This procedure is identical to that of the external phone book. The

first option in the submenu of a phone book contact is the Choose

function. Once this function is confirmed with OK, a connection is esta-

blished.

Unfortunately, it is not possible to copy and export data from the mobi-

le phone’s phone book to the Twin-Phone phone books.

14.1 Internal phone book

The second function Delete allows you to delete the stored contact.

Upon confirming this option once with the OK key, the prompt Are you

sure you want to delete contact will be displayed. If you want to

abort the deletion process, press either the ESC key (key 3) or the call

termination key. You can also confirm the prompt by pressing the OK

key in order to delete the contact.

Add new contact

To add a new contact or to search for a saved contact, select the in-

ternal phone book. If the device is being used for the first time or if

no contacts have yet been stored, the internal phone books directo-

ry is empty. Press the shift key to open the Phone book menu. You

must confirm Add contact for each new entry. For better conveni-

ence, the upper part of the display will show Enter name. Now follow

the steps as described in chapter 7.3.

With the third function Edit name, you can correct the data for any

selected contact. Please refer to chapter 7.3 for the respective key

functions.

Save the name by pressing the call answering key.

The fourth function Edit number allows you to modify the saved pho-

ne number for this contact.

Then enter the phone number for this contact. Confirm the entered

data again by pressing the call answering key.

With the fifth function Voice dial, you can add a voice tag for the se-

lected entry. Open the Store tag submenu to record the tag. The de-

vice is ready to record when Record 1 ... is flashing on the display.

Simultaneously, you will hear a short beep, which indicates that the

recording process will commence shortly. Say the name for this contact

in a normal voice into the microphone of your HFCK.

Search stored contacts

In the internal or external phone book, you can also search for

stored contacts. If you open the internal phone book in the phone

book menu, you will be provided with a list of all stored contacts in al-

phabetical order. By pressing the shift key once, the submenu with the

two functions Add contact and Search contact will open. If you

confirm Search contact with the OK key, Enter name to search will

be displayed while the cursor is flashing.

Wait a few moments for Record 2 ... to flash on the display. A short

beep again indicates that the recording process will start shortly. Re-

peat the message of the voice tag you want to record. The voice tag

has been recorded successfully if the display shows Tag stored.

Enter the first letter of the required contact and press the call answe-

ring key to confirm. All corresponding names will immediately be dis-

played. This list starts with the contact, which best matches your search

criteria.

You can choose the relevant contact using the scroll keys. Select the

required contact so that it is highlighted in black and then press OK

If the display should read Difference between records too big, the

records 1 and 2 are too different from each other to be identified as

identical voice tags by the device. In this case, repeat the recording

process as described above. Avoid any background noise while recor-

ding.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

14.2 External phone book

If the display reads Record is similar to existing one, distinguish

the new voice tag from the existing one by, for example, also stating

the first and last name of the contact.

This second menu of the phone book, which can be opened with the

OK key, allows you to access the data stored on your SIM card. The

external phone book will be active as soon as a SIM card is inserted

into the Twin-Phone card slot or the SAP profile is activated.

Once the voice tag has been recorded successfully, you can listen to the

voice tag using the function of the Voice dial submenu. For this, confirm

Play tag.

Note:

The mobile phone book cannot be accessed. In order to

store entries on the SIM card, select your SIM card as the

storing location for phone book contacts in the settings

menu of your mobile. The Twin-Phone is otherwise not able

to access the entries.

In the main menu, you can set the volume of the recorded voice tag,

namely by going to Setup, Audio, Volume, Voice-tag volume.

Note:

The voice tag will only be recorded if you have stored the

corresponding entry in the internal phone book. Voice

tags cannot be stored in the external phone book.

In HF profile, the external phone book is not active.

If the external phone book can be accessed and if you select this

using the OK key, up to 500 contacts stored on the SIM card will be

displayed in alphabetical order. The number of the entries stored on

your SIM card depends on the network operator. If a network operator

offers SIM cards with a capacity of 1000 entries, the Twin-Phone will

only show the first 500 contacts of the external phone book.

You can use the voice dial function by means of the stored voice tag. If

the screen saver is displayed, you can voice dial by pressing and holding

the call answering key for approx. 3 seconds until the display reads Tell

voice tag. Say the required name into the microphone of your HFCK

from the UNI System 8. The phone is now connecting. When using the

voice dial function and the device displays the message Unrecognised

voice tag or Error recognising voice tag, repeat recording.

In the following, you will find a summarised listing of frequently used

functions as the external phone book is analogue to the internal

phone book:

Note:

Please note that the stored voice tag and the use of the

voice dial function depend on the respective user’s voice.

The function will only work properly if the voice tag and the

voice dial were recorded and spoken by the same person.

Use the call answering key to establish a connection to the phone of the

contact saved in the list. You can open contacts by pressing the OK key.

The corresponding submenu with four options for this phone book ent-

ry will be displayed after pressing the shift key. Voice dial for entries

stored in the external phone book is not available.

Sometimes the voice tag recording is made at a too low or too high

volume depending on the background noise within the cabin. Repeat

the voice tag recording according to the instructions.

Note:

If a voice dial function is available with your mobile, ple-

ase note that the mobile phone voice dial cannot be applied

to the Twin-Phone. This is not possible as the voice tags are

stored in the mobile memory yet not on the SIM card.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

by pressing the call answering key or end a call by pressing the call

termination key. You can also confirm the name in the Dialled num-

bers register with the OK key and make a call by pressing the call ans-

wering key.

15. Call registers

This function is active if a SIM card has been inserted in the Twin-Pho-

ne card slot or if either the SAP or Hands-free profile has been acti-

vated.

If you first press the OK and then the shift key for a contact, you can

open the corresponding submenu for this contact. In this menu, three

functions are available: Dial, Add number to phone book and De-

lete number.

Here, four submenus are available: Dialled numbers, Received

calls, Missed calls and Clear call registers. The individual call re-

gisters of the Twin-Phone are empty when the phone is being used for

the first time or if the registers were cleared. They will only display in-

formation for connections, which were established while the Twin-Pho-

ne was switched on.

If you confirm the Dial function with the OK key, a connection will au-

tomatically be established to the phone whose number you have di-

alled. You may disconnect by pressing the call termination key.

Note:

The Twin-Phone is not able to access the mobile phone

call registers.

The Add number to phone book function can also be accessed by

pressing the OK key. The display will then read Choose phone book

while you can select either the internal or the external phone book.

Then enter a name via the SWRC (if the person, whose number you

have dialled, has not yet been entered in the phone book) and then

confirm this with the call answering key.

The registers will only list the respective phone number

if the phone of the respective person called also transmits

their mobile number. The registers will only list names if cor-

responding entries were stored in the internal or external

phone book.

In HF profile, the external phone book is not active.

The data stored there cannot be listed in the call registers if

the HF profile is active.

The display will then read Enter number. If the number is not display-

ed automatically, enter this using the number keys and confirm with the

call answering key.

In these registers, you can call any person, whose telephone number

and name are displayed, by pressing the call answering key. The regis-

ters will show Unknown number if the called person’s mobile does

not transmit the respective number. In this case, it is not possible to

return a call by pressing the call answering key.

You can select the Delete number function by pressing the OK key. If

deletion was unsuccessful, the display will read Number deleting er-

ror. In this case, repeat the above steps. If you do not want to delete

the number, you can return to the submenu for the respective contact

by pressing the call termination key.

You can clear individual registers by first opening them and then pres-

sing the shift key once. The display will then read, for example, Recei-

ved calls menu - Clear list.

15.2 Received calls

The Received calls submenu lists calls with date and time data, which

you received with the Twin-Phone (and not with the mobile).

15.1 Dialled numbers

Press the call answering key if you want to call the selected contact.

You can quit this list by pressing the call termination key. If you select

one of the contacts listed in the Received calls register with the OK

key, information on this particular call will be displayed. If you then

press the shift key, three options are available: Dial, Add number to

phone and Delete number. You can list these with the OK key or quit

them by pressing the call termination key. Please refer to the descripti-

on of the Dialled numbers submenu for details.

In the Dialled numbers submenu, you can retrieve information on

persons you have called using the Twin-Phone. The names of the called

persons, which are listed in the Twin-Phone phone book, will be dis-

played directly, otherwise the dialled number, date and time of the call

will be listed in the register.

Scroll to the entry of the dialled number, now you can either make a call

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

15.3 Missed calls

16. SMS

The Missed calls submenu lists entries for the calls you missed while

the Twin-Phone was switched on.

The SMS menu is activated when a SIM card is inserted in the Twin-

Phone card slot or when the SAP profile is active. In the SMS menu,

three submenus are available: Inbox, Write SMS, SMS settings.

If you confirm one of the entries in the register with the OK key, infor-

mation on the missed call will be displayed. Please refer to the descrip-

tion of the Dialled numbers submenu for details.

Note:

For your and other motorists’ safety, we do recommend

not to write and/or read an SMS while driving.

15.4 Clear call registers

16.1 Inbox

Here, you can simultaneously clear all three registers (Dialled num-

bers, Received calls and Missed calls) by pressing the OK key. If

you do not want to clear these registers, press the call termination key

instead of the OK key.

When a message is received, this will be indicated by an icon symboli-

sing a closed envelope which is located in the upper part of the screen

saver. An SMS tone will additionally sound to indicate that you have

received an SMS. If you want to read the received message, open the

main menu with the shift key, select the SMS, Inbox menu with the

OK key and open the unread message.

If you only want to clear a particular register, open the respective re-

gister in the Call registers menu with the OK key, press the shift key

and select Clear list with the OK key.

Unread SMS are indicated in the Inbox menu by an icon on the left-

hand side symbolising a closed envelope. Read SMS are symbolised by

an open envelope.

Start the deletion process by confirming the Are you sure you want

to clear list prompt with the OK key. If you do not want to clear the

list, terminate the process by pressing the call termination key.

Select the Inbox submenu to see a list of received SMS. If there is an

entry for the sender in the internal or external phone book, the

name of the sender will be displayed.

If you want to read an SMS, select it with the OK. If the received text is

too large to be displayed in full, you can use key 8 to scroll down to the

end of the SMS.

16.2 Message options

When you open the inbox and confirm this with OK, five options for this

SMS will be displayed. Using the first option Dial, you can call the sen-

der of the selected SMS.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

With the second option Add number to phone book, you can save

the sender’s number either in the internal or in the external phone

book.

of the display while the entry field is empty. In the bottom, the display

will read Dial or choose phone book. You can now enter the required

number with the number keys, to which you want to send your SMS.

The third option is Reply. If you confirm this with the OK key, the dis-

play will prompt Message text. You can now enter a text using the

number keys.

If you want to enter a number from the internal or external phone

book, you can open the two phone books with the shift key and select

a contact.

Press the OK key to send the written reply. In the bottom of the display,

it will read Dial or choose phone book. When you confirm this

prompt with the call answering key, a reply will be sent to the displayed

number. If you want to send your reply to a different person, open the

phone book by pressing the shift key and then select first either the

internal or external phone book and then the recipient.

16.4 Message settings

In this menu, the following four submenus are available: Service cen-

tre, Delivery report, Validity time and SMS language, which can

be selected with scroll keys 2 and 8 and confirmed with the OK key.

If your SMS has not been sent, the display will, for a few moments, read

Message sending error. Check whether sufficient reception is provi-

ded and that you entered the correct number. Then try again.

Service centre

With this option, you can display the Service centre number of your

network operator. You can quit this menu by pressing the call answe-

ring key.

Please note that it is not possible to automatically reply if the sender’s

number was not transmitted.

Note:

No SMS can be sent without the correct service centre

number. Delete the individual digits of the number from

right to left and/or from below upward by pressing the call

termination key. Your network operator will provide you with

the correct number.

With the fourth option Forward, you can forward any selected recei-

ved SMS to a chosen number. Confirm this option with the OK key. The

SMS to be forwarded will be displayed below the Message text hea-

der.

If you wish to do so, you may also edit the message text. Please note

that the number keys must be activated for this (see icon in the bottom

left corner of the display). If the icon shows arrows, press the shift key

once in order to activate the number keys.

Delivery report

Here, you can select whether you want to receive a delivery report on

the SMS sent from your mobile. The delivery report acts as a confirma-

tion that the message was received by the recipient’s phone.

If you want to enter a number from the internal or external phone

book, open the phone book with the shift key and select the respective

contact.

Validity time

Here, you can choose how long the network is supposed to try to send

your SMS. The device will try to send your SMS for a maximum of one

week. If this validity time period expires and your SMS was not sent

during this period, you will receive a delivery report with the message

Undelivered. Press the call termination key to quit the menu.

With the fifth option Delete SMS, you can delete a selected received

SMS.

SMS language

16.3 Writing messages

In this menu, one of the following languages can be selected: GSM,

Deutsch, English, Français, Polski.

Open this menu with the OK key to write an SMS. The text can be en-

tered with the number keys of the SWRC. Press the call answering key

to send the SMS. The Recipient number will now be shown in the top

The Twin-Phone uses two types of SMS coding. With the first, you can

write SMS with a text consisting of up to 160 characters. This is used

for the selectable SMS languages: German, English and GSM.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

The second coding is used, amongst others, for Latin text with particu-

lar characters such as French accents. The message text is limited to

70 characters as more than one character is used when coding these

characters. This SMS coding type is used for the French and Polish

SMS languages.

SMS Tone

With this option, you can choose from five different SMS tones. Confirm

your selection with the call termination key.

Language

Here, you can select the language in which the menu is displayed. Avai-

lable languages are German, English, French and Polish. Confirm

your selection with the call termination key.

Note:

The language is set to GSM as default when the phone

leaves the factory. Special characters will not be sent. If you

want to use language specific special characters select the

German, French or Polish SMS language.

Phone settings

Select Phone settings with the OK key. Three submenus are availab-

le: Operator selection, Auto answer and Send my caller ID.

17. Settings

Operator selection

The operator selection can be set to Automatic and Manual. Auto-

matic means that the network, which is provided at your location, is

selected automatically. If you have selected Manual, the device will

start to search for a network. Then Choose network will be displayed.

It lists the network available at your location. Your Home network is

ticked. You can choose the network provided by roaming partners at

any time. Networks, for which no roaming agreement exists, are mar-

ked with a cross. These cannot be chosen.

The Setup menu comprises five items: Display, Audio, Language,

Phone settings and System settings.

Display

Choose option Active brightness to modify the display’s active bright-

ness using the scroll keys 4 and 6. The black bars indicate the level of

brightness. Confirm your selection with the OK key. If you do not want

to change the set level, press the call termination key.

With the option Idle brightness, you can adjust the level of active

brightness when the phone is not being used. With the third option, you

can set the display Contrast.

Quit this menu by pressing the call termination key.

Auto answer

In this submenu, you can choose whether the Twin-Phone is to auto-

matically answer a call and, if yes, after how many seconds. Press the

call termination key to confirm your selection.

Audio

Open the Audio submenu by pressing the OK key. Here, you can adjust

the Volumes and Tones.

Send my caller ID

You can choose whether you want to transmit your phone number (Yes)

or not (No). Press the call termination key to confirm your selection.

Volume

Here, you can adjust the Ring tone volume, Talk volume and the

Voice-tag volume. Follow the steps described in the Display section.

Ring tone

Here, you can select the ring tone. With the OK key, the circle to the left

of the selected ring tone name is ticked and the ring tone will sound.

Confirm your selection with the call termination key or scroll down to

another ring tone.

Key tone

Here, three options are available: Tone off, Standard and DTMF. Al-

ways confirm with the call termination key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu navigation

System settings

Change allocated numbers

Five options are available: Date and time, Turn-off time, Telematic

keys, Default and Version Info.

If you open the telematic keys submenu with the OK key, you can

choose from two speed dial options: Edit info number and Edit ser-

vice number. After having confirmed your selection with the OK key,

you can enter the required number. Press the call termination key to

confirm your selection.

Date and time

Here, you can set the date displayed in the first line. Use the scroll keys

2 and 8 to select the respective data in ascending or descending order

for the day, month and year. Press and hold the scroll key to scroll fas-

ter. With the scroll key 6, you can move the cursor in each line from left

to right and then to the next line.

Emergency calls

If you press and hold the two telematic keys simultaneously for ap-

prox. 3 seconds, a connection to the emergency services (112 in Ger-

many) is established. Use this number only in case of emergency (the

emergency telephone number is stored in Default).

In the second line, you can select the Date format. You have two

options: yyyy/mm/dd (for year/month/day) and dd/mm/yyyy (for day/

month/year). Make your selection with the scroll keys 2 and 8. Press the

scroll key 6 for moving to the next line.

You can then set the Time – please follow the steps described in the

Date and time section.

Default

If you want to reset your Twin-Phone to Default, open the Default

submenu. If you want to terminate this process, press the call termina-

tion key. Upon confirmation with the OK key, System restart will be

displayed. The device will automatically switch off and restart. In doing

so, the original settings are restored for certain menu items. The Twin-

Phone and the SWRC must be re-paired after each restart.

In the fourth line, you can select the time format (12 or 24 hours).

Confirm all settings with the OK key to complete.

Turn-off time

Here, you can choose whether and after what time the Twin-Phone is

to switch off automatically when you have turned off the engine of your

vehicle and leave the Twin-Phone in the hang-up cup of your hands-free

car kit.

Version Info

This contains the manufacturer’s address as well as the hardware (HW)

and software (SW) version codes of the Twin-Phone for possible inqui-

ries with the manufacturer. Press the call termination key to quit this

submenu.

Note:

Please note that the vehicle’s battery will be continuously

discharged as long as the Twin-Phone is switched on.

Press the call termination key to confirm your selection.

Telematic keys

The two black keys of the Twin-Phone just below the display are the

telematic keys. These are speed dial keys to which you can allocate one

phone number each.

If you press and hold one of these keys, a connection is automatically

established to the phone, whose number was allocated to this key. The

left key is marked with a white i and can be used as speed dial key, e.g.

for an info number. The right key shows a white spanner and could, for

example, be used for speed dialling a service number.

The Default submenu does not comprise numbers for the speed dial

function of the two telematic keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional information

18.3 Information about GNU General Public License (GNU

GPL)

Please note that the operating system of the navigation system you use contains free software, the codes of which

are, however, under licence. Hereunder, information is provided on the use, reproduction, distribution and processing

of this software. Furthermore, a note on the exclusion of liability is included. Due to legal circumstances the following

textes are in English. On the Internet sites mentioned in this user manual you have the possibility to request the re-

spective source codes or to download them yourself. http://www.gnu.org/licenses/gpl.html

18. Service and regulations

18.1 Service

Please contact our service team if you have any questions in this matter:

Bury GmbH & Co. KG

Robert-Koch-Str. 1-7

D-32584 Löhne

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Hotline: +49 (0) 180 - 584 24 68*

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Fax:

+49 (0) 180 - 584 23 29*

* 0.12€/Min. from Deutsche Telekom AG landlines

E-mail: [email protected]

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

In case of complaints, please return the product directly to our service desk:

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU

General Public License is intended to guarantee your freedom to share and change free software--to make sure the

software is free for all its users. This General Public License applies to most of the Free Software Foundation‘s soft-

ware and to any other program whose authors commit to using it. (Some other Free Software Foundation software is

covered by the GNU Library General Public License instead.) You can apply it to your programs, too. hen we speak of

free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you

have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive sour-

ce code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and

that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny

you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if

you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program,

whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they,

too, receive or can get the source code. And you must show them these terms so they know their rights. We protect

your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission

to copy, distribute and/or modify the software. Also, for each author‘s protection and ours, we want to make certain

that everyone understands that there is no warranty for this free software. If the software is modified by someone

else and passed on, we want its recipients to know that what they have is not the original, so that any problems intro-

duced by others will not reflect on the original authors‘ reputations. Finally, any free program is threatened constant-

ly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent

licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be

licensed for everyone‘s free use or not licensed at all. The precise terms and conditions for copying, distribution and

modification follow.

Bury GmbH & Co. KG

Im Hause DPD Depot 103

Robinienweg

D-03222 Lübbenau

Phone: +49 (0) 5732 9706 170 / -431

Fax:

+49 (0) 5732 9706 470

Suggestions and feedback are always welcomed.

18.2 Regulations

Notes on battery disposal

In some countries, you are required by law to dispose of used rechargeable batteries at

recycling stations according to the guidelines. Do not dispose of these batteries in nor-

mal waste. Please inquire where you can dispose of normal and rechargeable batteries.

Depending on the recycling station, normal and rechargeable batteries containing ha-

zardous substances must be disposed of separately. Batteries, which contain hazardous

substances, are marked with chemical symbols (Cd for cadmium, Hg for mercury, Li for

lithium, Pb for lead).

Notes on disposal of electrical equipment

GNU GENERAL PUBLIC LICENSE

With the implementation of the directive on electrical and electronic equipment, used

electrical appliances must no longer be disposed of together with normal waste since

24th March 2006. If you own a used appliance, you are required to leave it at the desi-

gnated collection or municipal recycling stations. Electrical waste will be accepted free

of charge at these stations.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it

may be distributed under the terms of this General Public License. The „Program“, below, refers to any such program

or work, and a „work based on the Program“ means either the Program or any derivative work under copyright law:

that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional information

into another language. (Hereinafter, translation is included without limitation in the term "modification"). Each licen-

see is addressed as "you".

work, complete source code means all the source code for all modules it contains, plus any associated interface defi-

nition files, plus the scripts used to control compilation and installation of the executable. However, as a special ex-

ception, the source code distributed need not include anything that is normally distributed (in either source or binary

form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,

unless that component itself accompanies the executable.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.

The act of running the Program is not restricted, and the output from the Program is covered only if its contents

constitute a work based on the Program (independent of having been made by running the Program). Whether that

is true depends on what the Program does.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering

equivalent access to copy the source code from the same place counts as distribution of the source code, even though

third parties are not compelled to copy the source along with the object code.

1. You may copy and distribute verbatim copies of the Program‘s source code as you receive it, in any medium, provi-

ded that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of

warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other

recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of

transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program,

and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet

all of these conditions:

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.

Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate

your rights under this License. However, parties who have received copies, or rights, from you under this License will

not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permis-

sion to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not

accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you

indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying

the Program or works based on it.

a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any

change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the

Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running

for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copy-

right notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may

redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:

if the Program itself is interactive but does not normally print such an announcement, your work based on the Program

is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable

sections of that work are not derived from the Program, and can be reasonably considered independent and separate

works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as part of a whole which is a work based on the Program,

the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to

the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section

to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to con-

trol the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another

work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or

distribution medium does not bring the other work under the scope of this License.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a

license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You

may not impose any further restrictions on the recipients‘ exercise of the rights granted herein. You are not respon-

sible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited

to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the

conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as

to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a conse-

quence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free re-

distribution of the Program by all those who receive copies directly or indirectly through you, then the only way you

could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the

section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest

validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribu-

tion system, which is implemented by public license practices. Many people have made generous contributions to the

wide range of software distributed through that system in reliance on consistent application of that system; it is up to

the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot

impose that choice.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form

under the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the

terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted

interfaces, the original copyright holder who places the Program under this License may add an explicit geographical

distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus

excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to

time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems

or concerns.

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than

your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source

code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software inter-

change; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alter-

native is allowed only for noncommercial distribution and only if you received the program in object code or executab-

le form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable

Each version is given a distinguishing version number. If the Program specifies a version number of this License which

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional information

applies to it and „any later version“, you have the option of following the terms and conditions either of that version or

of any later version published by the Free Software Foundation. If the Program does not specify a version number of

this License, you may choose any version ever published by the Free Software Foundation.

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w‘.

This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c‘ for details.

The hypothetical commands ‘show w‘ and ‚show c‘ should show the appropriate parts of the General Public License.

Of course, the commands you use may be called something other than ‘show w‘ and ‘show c‘; they could even be

mouse-clicks or menu items -whatever suits your program. You should also get your employer (if you work as a pro-

grammer) or your school, if any, to sign a „copyright disclaimer“ for the program, if necessary. Here is a sample; alter

the names:

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are diffe-

rent, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,

write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the

two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse

of software generally.

Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision‘ (which makes passes at compi-

lers) written by James Hacker.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE

EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOL-

DERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM „AS IS“ WITHOUT WARRANTY OF ANY KIND, EITHER EX-

PRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PRO-

GRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is

a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this

is what you want to do, use the GNU Library General Public License instead of this License.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,

BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMA-

GES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF

DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE

OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achie-

ve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most

effectively convey the exclusion of warranty; and each file should have at least the „copyright“ line and a pointer to

where the full notice is found.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public Li-

cense as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later

version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even

the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details. You should have received a copy of the GNU General Public License along with this program;

if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

19. Index

Antenna, GSM

Audio

5, 15

Service number, edit

Shift key

Auto answer

Auto profile

BT code

Call answering key

Call registers

Call termination key

Current connection

Date, set

16-17

18, 19

SIM card

11-15, 17, 26

SIM card slot

SMS language

SMS tone

SMS, write

Speed dial

31-32

9-10

26-28

19-20

11, 21, 35

20-21

12, 25

12, 16-17

Standby mode

11, 32

Steering wheel remote control

Switching the phone off

SWRC battery, change

SWRC, installation

SWRC, key functions

SWRC pairing

7-10

6-7

Default

Delivery report

Disconnect BT

Display

Emergency calls

External phone book

HF profile

8-9

7-8

34-35

Telematic keys

Time, set

Home network

Hotline

14, 33

Transmission range

Turn-off time

Info number, edit

Installation overview

Internal phone book

Key tone

12, 22-25

TWIN card

Twin-Phone, installation

Validity time

Version info

Language menu

Local BT name

Main menu

Voice dial

Volume

Volume control

23-25

Missed calls

12, 15

Network operator

Number keys

OK key

Pairing

17-20

Pairing, delete

Phone book contacts

PIN code

9-10, 22

14, 15

Power supply

Restart

13, 16, 17, 35

Ring tone

12, 32-33

SAP profile

12, 13, 15-16, 19

Scroll keys

Sending caller ID

Service centre

Service contact

Download from Www.Somanuals.com. All Manuals Search And Download.

Version 10/2006

25.0971.0-02-191006

Subject to alterations and errors expected

Download from Www.Somanuals.com. All Manuals Search And Download.

Bury GmbH & Co. KG

Robert-Koch-Str. 1-7

D-32584 Löhne

Hotline Tel: +49 (0)180 - 584 24 68*

Hotline Fax: +49 (0)180 - 584 23 29*

E-Mail:

[email protected]

www.bury.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Targus Network Card APA10AP User Manual
Toastmaster Electric Heater E6UAC 20 User Manual
Toshiba Computer Drive SDFCP93GEA01 User Manual
Toshiba DVD Player 24AF45C User Manual
Toshiba TV DVD Combo SD V290 S TU User Manual
Tyco Electronics Car Video System 1937L User Manual
Uniden Cordless Telephone XSA650 User Manual
Universal Smoke Alarm 1422 User Manual
Volkswagen Automobile Caravelle User Manual
Vulcan Hart Fryer 1ER50C User Manual