XSA660
A N D
XSA650
OWNER’S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Handset Retainer - holds handset in base for
9. Memo Button - Recording a memo.
10. Skip Button - Skip the message.
11. Ring Time Switch - Ring time select switch.
12. Answer Button - answering machine ON OFF
Button.
13. Page Button - locates the handset.
14. Clock Button - Adjust time and day.
15. Mic - Microphone.
16. PIN Button - change PIN number.
17. OGM Button - Out Going Message Recording.
18. Repeat Button - Message Repeat.
19. Delete Button - Delete message(s).
Wall Mounting.
2. Ringer on/off switch - Base Ring ON or OFF.
3. Speakerphone Button and LED - indicates the
phone is in speaker mode.
4. Speaker Volume - Volume up and down Button.
5. Status LED - Indicates the phone is in use or the
handset is charging.
6. Message Counter LED - Display for number of
messages.
7. Recording Time Switch - Select Recording
time.
8. Play/Stop Button - Message Play and stop.
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is a very condensed version of your
owners manual and does not attempt to explain
any of the advanced features of your phone.
Initial Setting
A simple guide to setting
up your new phone.
XSA660
and
XSA650
CONNECTIONS
Plug the AC adaptor into a standard
wall socket and make sure it is
switched on.
Please confirm the model
number of your telephone.
Plug the AC adaptor cord into the 9V DC
input jack at the rear of the base unit.
BATTERY CHARGE
Start
Plug the battery into each handset.
Place each handset on the base for 15-
20 hours for the battery to fully charge
before you use the phone..
Here!
Quick Reference Guide
Only the XSA660 has 2 handsets.
Important Note:
Model XSA660 - Lay both handsets on the base after
charging is complete, for at least 2 seconds to set the
security code.
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the mem button again.
Making/Receiving Calls
Enter the memory location number
where you wish to store the phone
number (0-9).
DIALLING A STORED NUMBER
mem
Press the talk button.
Press the mem button followed by the
memory location number.
MAKING A CALL
Press the talk button.
The “talk” indicator will stop blinking
when a dial tone is received.
Answering Machine
Dial the number and make the call.
To activate the answering machine
press the answer button on the base
until the digital display lights up.
To hang up press the talk button or
put handset on base.
The prerecorded outgoing message will
play.
RECEIVING A CALL
When the phone rings pick up handset from
base.
PLAYING YOUR MESSAGES
OR
Press the play button on the base.
Press the talk button if the handset is away
from the base.
DELETING YOUR MESSAGES
Press delete during the messages: the
system beeps and plays the next
message.
OR
Push speaker on the base to use the speaker
phone.
STORING A NUMBER IN MEMORY
Ø
speaker
Press the mem button on the handset.
play
delete
Enter the phone number you wish to
store.
Ø
answ
er
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Included in your Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation
Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the Telephone Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Applying power to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Desk or Tabletop Installation
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting on a Standard Wall Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Direct Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting up your Phone
Raising the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjusting Ringer Volume and Earpiece Volume . . . . . . . . . . . . . . . . . . . . 11
Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Charging the Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto Digital Security Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Your Phone
Making and Receiving the Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing Channels, Flash and Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Storing a Number in Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chain Dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Erasing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Replacing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the Handset Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Call Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3 Way Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using Your Answering System
Switching the Answer Machine on/off . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Reviewing Time and Day Stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting your Outgoing Message (OGM) . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting the Toll Saver Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playing New Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Repeating a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Skipping a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Deleting a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Deleting all Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Message Full Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Screening Incoming Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Leaving a Memo Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Setting Your PIN Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using a Touch-Tone Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
One-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Download from Www.Somanuals.com. All Manuals Search And Download.
INCLUDED IN YOUR PACKAGE
To get the most from your
phone, please read this
owner’s manual thoroughly.
Be sure to complete and mail
the product registration form.
Handset
2nd Handset
(XSA660 only)
Base
If any of these items are
missing or damaged, contact
your place of purchase
immediately.
Rechargeable Battery
AC Adaptor
(2nd Adaptor XSA660 only)
Charging Cradle
(XSA660 only)
(BT434)
(2 x batteries XSA660)
Long Telephone
Cord/Plug
Long Telephone Cord
(NZ Only)
Wall Mount
Adaptor
(Australia Only)
✃
This Owner’s
Manual
✃
✃
Registration Card
and other printed
materials
Mounting Screws
2 x Memory Stickers
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT ELECTRICAL CONSIDERATIONS
Unplug all electrical appliances when you know an electrical storm is
approaching. Lighting can pass through your household wiring and damage any
device connected to it. This phone is no exception.
Warning: Please do not attempt to unplug any appliance during an electrical
storm.
Caution: Changes or modifications to this product not expressly approved by Uniden,
or operation of this product in any way other than as detailed by this
Operating Guide, could void your authority to operate this product.
Range
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications. We have rated
this phone to operate at a maximum distance with the qualification that the
range depends upon the environment in which the telephone is used. Many
factors limit range, and it would be impossible to include all the variables in our
rating. The Maximum Range rating of this phone is meant to be used as a means
of comparison against other range claims.
Telephone Line Problems
If you are having trouble with your telephone service, you must first disconnect
your phone to determine if it is the cause of your problem. If you determine that it
is the cause, you must leave it disconnected until the trouble has been corrected.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
Before you read anything else, please observe the following:
Warning!
UNIDEN DOES NOT represent this unit to be waterproof.
To reduce risk of fire, electrical shock or damage to the unit, DO NOT expose this
unit to rain or moisture.
Rechargeable Nickel-Cadmium Battery Warning
•
•
This equipment contains a rechargeable Ni-Cad battery.
The rechargeable Ni-Cad battery contained in this equipment may explode if
disposed of in a fire.
•
•
Do not short-circuit the battery.
Do not charge the Ni-Cad battery used in this equipment in any charger
other than the one designed to charge this battery as specified in this the
owner’s manual. Using another charger may damage the battery or cause
the battery to explode.
•
Rechargeable Nickel-Cadmium batteries must be recycled or disposed of
properly!
Warning!
Under power failure, this telephone will not operate. Please ensure that a separate
phone not dependant on local power is available during emergencies.
The exclamation point within a triangle is intended to
alert the user of an important operating or maintenance
instruction.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, these basic safety precautions should always
be followed to reduced the risk of fire, electrical shock, and injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning, and use a dry cloth,
without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bath tub, shower, wash
bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable stand, or table. The telephone may
fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation. To protect the product from overheating, these openings must not
be blocked or covered. This product should never be placed near or over a
radiator or heat register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result in the risk
of fire or electrical shock.
10. Never push objects of any kind into this product through cabinet slots, as they
may touch dangerous voltage points or short out parts that could result in a
risk of fire or electrical shock. Never spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product. Take it to
qualified service personnel when service or repair work is required. Opening or
removing covers may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock when the appliance is
subsequently used.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If Liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the operating
instructions.(Adjust only those controls that are covered by the
4
Download from Www.Somanuals.com. All Manuals Search And Download.
operating instructions. Improper adjustment of other controls may
result in damage and will often require extensive repair work by a
qualified technician.)
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
Radio Interference
Radio interference may occasionally cause buzzing and humming in your cordless
Handset, or clicking noises in the Base Unit. This interference is caused by external
sources such as a TV, refrigerator, vacuum cleaner, fluorescent lighting, or
electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too
distracting, please check around your home to see what appliances may be
causing the problem. In addition, we recommend that the Base not be plugged
into a circuit that also powers a major appliance because of the potential for
interference. Be certain that the antenna on the unit is fully extended.
In the unlikely event that you consistently hear other voices or distracting
transmissions on your phone, you may be receiving radio signals from another
cordless telephone or other source of interference. If you cannot eliminate this
type of interference, change to a different channel (refer to page 17).
Finally, it should be noted that some cordless telephones operate at frequencies
that may cause interference to nearby TVs and VCRs. To minimise or prevent such
interference, the base of the cordless telephone should not be placed near or on
top of a TV or VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
More Than One Cordless Telephone
1. If you want to use more than one cordless telephone in your home, they must
operate on different channels. Press the channel key to select a channel that
provides the clearest communication.
2. Each telephone device that you connect draws power from the phone line. We
refer to the power drawn as the devices Ringer Equivalence Number (REN).
The REN is shown at the bottom part of your telephone. If you are using more
than one phone or other device on the line, add up all the RENs. If the total is
more than 3, your phones may not ring.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WELCOME
Congratulations on your purchase of the Uniden XSA660 or XSA650 Cordless
Telephone. This phone is designed to exacting standards which provide reliability,
long life, and outstanding performance.
FEATURES
•
•
•
•
•
•
•
•
•
•
Handset Volume Ringer Controls
Talk/Battery Low Indicator
10 Day Battery Life
•
Multi Hand set
(up to 2, XSA660 only)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10 Channels (AUST)
25 Channels (NZ)
AutoTalk™
Ringer ON/OFF on the Base
15 minutes Recording time.
10 Step Speaker Volume control
Ring time Switch.
AutoStandby™
Speakerphone
Tone Dialling
2 Digit Message Counter.
Call Screening
10-Number Memory/Handset
Redial Key
Remote Operation away
from home
Flash Key
•
•
•
•
•
Time and Day Stamp
Selectable Outgoing Messages
2 Digit PIN Number
Toll Saver
Pause Key
Random Code Digital Security
UltraClear Plus™
AutoSecure™
Built in Flash Memory Backup
Page Button
™
AutoTalk allows you to answer a call by just removing the Handset from the
Base so you don’t have to waste time pushing buttons or flipping switches.
™
AutoStandby allows you hang up by simply returning the Handset to the Base.
™
The UltraClear Plus innovative technology, together with 10 (AUS) and
25 (NZ) different channels, virtually eliminates background noise and provides
you with the best possible reception during all of your conversations.
To protect you against misbilled calls which might result from your phone being
activated by other equipment, Random Code digital security automatically
selects one of over 65 thousand digital security codes for the Handset and Base
™
Unit. Also, the AutoSecure feature electronically locks your phone when the
Handset is on the Base.
To get the most from your phone, please read this Operating Guide thoroughly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Selecting a Location
Before choosing a location for your new phone, there are some important
guidelines you should consider:
• The location should be close to both a phone jack and power outlet.
• Keep the Base Unit and Handset away from sources of electrical noise such as
motors or fluorescent lighting.
• Be sure there is sufficient space to fully extend the Base Unit antenna.
• The Base Unit can be placed on a desk or tabletop or mounted on a wall.
• If you decide to mount your phone on the wall, make sure to change the
handset retainer so that the tab which holds the Handset faces up.
(See page 9 for more information.)
• You should charge your new phone for 15-20 hours before completing the
installation or using the Handset.
Telephone Line Outlet — Modular Jack
Most phone equipment available now uses modular jacks. Phone cords are fitted
with a molded plastic connector which plugs into this type of jack. If you do not
have modular phone jacks, contact you local telephone company for information
about their installation.
Connecting the Telephone Cord
Consider these safety guidelines before connecting the telephone cords:
CAUTION
•
•
•
Never install telephone wiring during a lightning storm.
Never touch uninsulated telephone wires or terminals.
Use caution when installing or modifying telephone lines.
Applying Power to the Base Unit
The XSA660 or XSA650 requires an AC outlet and the included AC Adaptor.
To relieve strain on the DC plug when the phone is placed on a desk or table,
connect the adaptor as shown below.
Wrap the power cord around the convenient
notch on the bottom.
Important: Place the power cord so that it
does not create a trip hazard, or where it
could become chafed and create a fire or
other electrical hazards.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DESK OR TABLETOP INSTALLATION
1. Plug the AC adaptor cord into the 9V DC input jack on the base.
2. Wrap the AC adaptor cord inside the molded strain-relief.
1
3
Use only the AC adaptor that
came with the phone.
2
5
4
Line in
From
Telephone
Jack
AC
Adaptor
3. Plug one end of the long telephone cord into
the TEL LINE jack on the base.
4. Plug the other end of the telephone cord into
the telephone wall jack. (remember, the phone
must be fully charged before you can use it.)
Use only the AC adaptor that
came with the phone.
5. Plug the AC adaptor into a standard 240V AC
wall outlet.
6. Fully extend the antenna on the base.
Wall Installation
Setting the handset Retainer for Wall mounting
1. Remove the handset retainer on the by base
sliding it upward.
2. Rotate the retainer 180˚ and flip over so the
tab is facing up.
3. Slide the retainer back onto the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Fit the Wall Mounting adaptor to the
Bottom of the telephone as shown.
Mounting on a Standard
Wall Plate
Use only the AC adaptor that
came with the phone.
The phone is designed to be mounted on a standard telephone wall plate.
1. Plug the AC adaptor into the base.
2. Place the AC adaptor cord inside the left molded channel cord holder.
3. Plug the telephone cord into the TEL LINE jack on the base.
7
1
3
5
2
4
6
4
AC
Adaptor
Line in
From
Telephone
Jack
4. Place the telephone cord into the right molded channel cord holder and plug
the other end of the cord into the wall jack. (Remember, the phone must be
fully charged before you can use it.)
5. Place the base on the posts of the wall plate, and slide downward to secure.
6. Plug the AC adaptor into a standard 240V AC wall outlet.
7. Fully extend the antenna on the base.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Directly on a Wall
If you do not have a standard wall plate, you can mount the phone directly on a
wall. Before mounting your cordless telephone, consider the following:
Select a location away from electrical cables, pipes, or other items behind the
mounting location that could cause a hazard when inserting screws into the wall.
Use only the AC adaptor that
came with the phone.
Make sure the wall material is capable of supporting the weight of the base and
handset; otherwise, damage to the unit could result.
Use #10 screws with anchoring devices suitable for the wall material where the
base will be placed.
1. Insert the screws, with their appropriate anchoring devices,
100mm apart. Allow 5mm between the wall and screw
heads for mounting the phone.
1
2. Fit the Wall Mounting Adaptor to the telephone Base.
3. Plug the AC adaptor into the base.
4. Place the AC adaptor cord inside the left molded channel
cord holder.
5. Plug one end of the long telephone cord into the TEL
LINE jack on the base.
6. Place the telephone cord into the right molded channel cord holder.
7. Place the base on the screws and push down until it’s firmly seated.
8. Plug the other end of the telephone line into the telephone wall jack.
(Remember; the phone must be fully charged before you can use it.)
9. Plug the AC adaptor into a standard
10
240V AC wall outlet.
10. Fully extend the antenna on the base.
3
5
4
7
6
2
8
Line in
From
9
Telephone
Jack
AC
Adaptor
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP YOUR PHONE
Raising the Antenna
Before using your phone, be sure to fully raise the antenna to the vertical position.
ADJUSTING RINGER/EARPIECE
VOLUME CONTROLS
Ringer Tone and Volume
1. While the handset is not in use, press vol/ringer key.
2. The phone has two ringer tones, each with two volume levels. Press the
vol/ringer key again until you hear the ringer tone and volume level you want.
When you hang up, the phone keeps the last setting selected.
Setting the Handset Earpiece Volume
1. While you are on a call, Press the vol/ringer key.
2. The phone has three receiver volume levels. Normal, High, and Max. Press
vol/ringer again until you hear the volume level you want.
When you hang up, the phone keeps the last setting selected.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Battery Pack
The rechargeable Nickel-Cadmium battery pack must be fully charged before using
your phone for the first time. Before plugging the phone line into your new phone,
you must charge the battery for approximately 15-20 hours without interruption.
1. Remove the Handset
battery cover.
The battery connector will fit
together only one way. Make
sure the connector is
properly aligned. Use only
the Uniden battery pack
(model BT-434)
2. Plug the battery’s cable
into the handset and
place the battery pack
inside the battery
compartment.
3. Replace the battery cover.
Charging the Handset
1. Place the handset on the base to charge. (The handset will charge only in
the face-down position.) OR place the handset on the charger keypad facing
forward (XSA660 only).
Replace the handset on the
base after use if convenient.
However recharging the
battery is only necessary
when the low battery
indicator is lit. On a
monthly basis use the phone
until the low battery
indicator appears. Then
charge the battery for 15-20
hours.
(Spare Handset - XSA660 only)
2. Make sure the status LED lights on the base or change LED lights on the
charger. If the LED doesn’t light, check to see that the AC Adaptor is plugged
in and switched on. Also that the Handset is making good contact with the
Base Unit and charger charging contacts.
Continuous Battery Charging
For the best battery performance, return the Handset to the Base Unit at the end
of the day. This keeps the battery fully charged.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Low Battery Indicator
When the battery pack in the handset is low and needs
to be charged, the talk/batt LED flashes once every
3 seconds.
trans
If this occurs while you are on the phone, you will
hear an alert tone. Complete your call as quickly as
possible, and return the handset to the base for charging.
The built-in Memory Backup
feature allows up to 1
minute to disconnect the old
battery pack and install a
new one without losing any
numbers stored in memory.
During a call
In Standby Mode
Only the talk button operates.
None of the buttons will operate.
The Handset beeps and the talk/batt The Handset talk/batt low LED flashes
low LED flashes once every 3 seconds. once every 3 seconds.
Complete your call as quickly as
possible.
You will not be able to make a call.
Return the Handset to the Base Unit
for charging.
Return the Handset to the Base Unit
for charging.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all battery contacts on the
handset and base about once a month. Use a pencil eraser or other contact
cleaner. Do not use any liquids or solvents, or abrasive materials.
pin
clock answer
page
mic
✃
contacts
(Spare charging cradle - XSA660 only)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Digital Code Security
To avoid unauthorised calls on your phone, a Digital Code feature is added to the
XSA660 and XSA650 phones. This Digital Code is shared only between the Handset
and the Base Unit. The code is set automatically when you first use the phone.
Place the Handset on the Base Unit. The status LED on the Base will blink
quickly, indicating that the code has been set.
If the Base Unit loses power while the Handset is off the Base, the Digital Code
may be erased. When this happens, the Handset will not function. To reestablish
communication between the Handset and Base Unit:
1. Restore power to the Base Unit.
2. Place the Handset back on the Base Unit.
3. The status LED on the base will blink quickly, indicating that the Digital Code
has been reset.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
USING YOUR PHONE
Making and Receiving Calls
The following features of the XSA660 and XSA650 phone are different depending
on the Handset’s Location when you make or receive a call.
Handset on Base
Handset off Base
When the phone rings, remove the
handset from the base. (Autotalk)
Press speaker button on the
base unit or talk on the handset.
Answer call
Make call
1. Remove the handset from the
base and press talk.
Note: You must use the
Handset to make a call.
2. The talk LED lights.
3. Listen for the dial tone.
4. Dial the number.
Hang up
Redial
Return handset to the base.
(AutoStandby) or press talk.
Press speaker button on the
base unit.
1. Remove the handset from the
base and press talk.
Note: You must use the
Handset to make a call.
2. Listen for the dial tone.
3. Press redial to dial the last
number.
Note: Sometimes when you press talk to hang up the phone, you may get an error tone
and the phone will not disconnect. If this happens, place the Handset on the Base
Unit or press talk again while holding the Handset close to the Base Unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Channels, Flash and Page
To change channels or access call waiting while the phone is in use, or to use the
one-way page to locate the Handset, follow these steps:
Handset
Press chan
Note: Change channels to help Handset to change channels
Base Unit
Note: You must use the
Changing
Channels
eliminate background noise
If the call waiting tone sounds,
press flash then 2 to accept the
waiting call. (Aus only)
- OR -
To return to the original caller
press flash then 1. (Aus only)
Note: The Base Unit does not
have flash. You must use the
Handset to access call waiting.
Flash
The flash + 2 call waiting
procedure toggles between
the incoming and original
call (and visa versa).
(Australia)
The flash + 1 procedure
will drop the current call
connection and pick up the
incoming call on hold.
If the call waiting tone sounds
during a call, press flash to
toggle between the incoming
and the original call.
Note: The Base Unit does not
have flash. You must use the
Handset to access call waiting.
Flash
(New
Zealand)
Note: When page is pressed on Press page on the Base Unit to
Page Find
the Base Unit, the Handset
beeps.
locate the Handset.
The paging feature does
not work when the phone is
in use.
Note: If you do not have the call waiting service, pressing flash may disconnect the
current call.
If the above flash operation does not work and you have the “Easy Call” service
follow your service provider’s instruction to operate “call waiting”.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Number in Memory
Your XSA660 or XSA650 phone has 10 memory locations per handset for storing
important telephone numbers.
1. Remove the handset from the base and press mem. The talk/batt low LED
flashes.
You have 20 seconds after
pressing mem to enter the
number you wish to store.
Otherwise, an error tone will
sound.
2. Enter the phone number you want to store (up to 16 digits).
3. Press mem and enter a number (0-9) on the keypad for the memory location
you want to use.
You hear a long beep and the talk/batt low LED goes out indicating the
number has been stored successfully.
If you select any keys other than 0-9, the handset will beep rapidly (error tone)
and no number will be stored.
Entering a Pause in Memory Dialling
If you would like to use a phone number stored in memory to access voice mail,
for example, you can store a pause in the phone number sequence.
Remember, the phone
number you wish to store
cannot have more than 16
digits, including the pause.
(The pause button counts as
one digit.)
To use this function, follow steps 1 and 2 in “Storing a Number in Memory,”
then press the pause button on the handset to place a 2 second pause in the
phone number sequence.
Follow the remaining steps in the “Storing a Number in Memory” section to
complete the operation.
Dialing a Stored Number
To dial a phone number stored in memory, press talk, then press mem and the
memory location (0-9). Your phone will dial the stored number.
If you attempt to dial a
memory location that does
not have a stored number,
the handset will beep rapidly
(error tone) and the phone
will not dial.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chain Dialling
After dialling a number you may be requested to enter a special access code, for
example, when performing a banking transaction.
1. Store the access code into one of the memory locations (0-9).
2. Dial the main number.
3. Press mem and the memory location where you stored the access code at the
appropriate time.
Erasing a Stored Number
1. Remove the handset from the base.
2. Press mem twice.
3. Press the memory location number (0-9) you want to clear. You hear a long
beep confirming that you have erased the number.
Replacing a Stored Number
Remember your XSA660 or XSA650 phone has 10 memory locations per handset,
represented by the numbers 0-9 on the keypad. If you store a phone number in
one of these locations, then store a different number in the same location later,
the new number will replace the previous one.
If you attempt to dial a
memory location that does
not have a stored number,
the handset will beep rapidly
(error tone) and the phone
will not dial.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Handset Number - XSA660 ONLY
Note: An error tone will sound and the programming procedure will be cancelled if
more than 20 seconds elapse between each keystroke entry or step.
1. Remove the Handset from the Base Unit or from the charger.
2. Press mem. The talk/batt low LED blinks.
3. Press trans
Call transfer will not operate
if the handset number has
not been set.
4. Enter the number you want to store to the Handset (1 or 2).
Note: If you stored the same number to each Handset, you can not transfer between
Handsets.
5. Press mem again.
A tone indicates that the Handset number is stored. (Default Handset number: 1)
Call Transfer - XSA660 ONLY
Call can be transferred between Handsets.
1. Press trans the other Handset will ring. The other Handset must be in Standby
mode to receive paging.
2. Press talk on the other Handset and the call is transferred from Handset 1 to 2.
3. If the Handset on the Base or charger, pick up the Handset (AutoTalk)
4. If the transfer is not picked up by the Handset, then after 60 seconds it will
return to the originating Handset.
3 Way Conference
During Handset talk mode, press the speaker button on the Base then you can
talk 3 ways. If you are already using the Base speaker phone, press the talk
button on one Handset.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the Answer Machine On/Off
1. To turn the Answering System on,
repeat ogm
memo
skip
press answer.
A tone sounds, and the current outgoing
message plays on the Base Unit speaker
and the Message Counter LED turns on. A
second tone sounds to indicate the unit is
ready to answer calls.
pin
clock answer
page
When the Message Counter
LED flashes, you have
unread new messages.
mic
✃
2. To turn the Answering System off, press
answer again. A tone sounds and the
Message Counter LED turns off.
Setting the Clock
The clock in your XSA660/650 Answering
System starts when power is applied to the
Base Unit. Follow these steps to set the clock to
the correct time.
repeat ogm
memo
skip
pin
clock answer
page
1. Press and hold the clock button until a
beep tone is heard and the day is
announced.
mic
✃
2. Press skip or repeat until the correct day
is announced.
3. Press clock again. Press skip or repeat
until the correct hour is announced.
Day of the Week Display
4. Press clock again. Press skip or repeat
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
0
-
until the correct minute is announced.
I
-
5. Press clock again. Press skip or repeat to
2
3
4
5
6
select AM [ A] or PM [ P].
-
-
-
-
-
-
-
6. Press clock to return to Standby.
The selected time and day is announced
For example, to set Tuesday at 3.10AM:
Saturday
Press and hold clock then “Sunday” will be
announced.
Press skip x 2 times, “Tuesday”, will be announced.
Press clock then skip 4 times “three, will be announced.
Press clock then skip 11 times “ten”, will be announced.
Press clock then skip 1 time “AM”, will be announced.
Press clock to finish, the complete time and day will be announced.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Reviewing Time and Day Stamp
1. Press clock. The speaker beeps, and the Time and Day Stamp is announced.
Setting your Outgoing Message (OGM)
When you receive a call, the Answering System answers and automatically plays
either a preset message or your personal Outgoing Message.
Preset Messages
The XSA660 or XSA650 has two messages programmed in its memory. If the
[REC TIME/ANN/4/1] switch is in either the four or one position, the first preset
message below plays. Incoming messages are limited to four or one minute
respectively. If the switch is set in the left position, (i.e., the “Announce Only”
position) the second message below plays, and no incoming messages are
recorded.
• Hello. No one is available to take your call.
Please leave a message after the tone.
IF THE REC TIME/ANN/4/1
switch is in the “Announce
Only” position, the message
Counter LED displays an A
when the system is in
Standby.
• Hello. No one is available to take your call (plays twice when set to ANN).
Recording a personal outgoing message
repeat ogm
memo
skip
1. To record an outgoing message, press and
hold ogm until a long tone is heard.
pin
clock answer
page
Start recording your message after you hear
the long tone.
2. Do not get closer than 300mm from the
microphone, and speak clearly while
mic
✃
You can record up to a 30
second outgoing message.
recording your message. When you are
finished recording. Press the play/stop key.
You hear a tone, and your message is played on the Base Unit speaker.
Selecting a Preset OGM
After you have recorded an outgoing message, you can set your Answering System
to play either a preset message or your outgoing message.
1. Press ogm. Your recorded outgoing
repeat ogm
memo
skip
message will begin to play.
2. While your recorded outgoing message is
playing, press ogm again to select the
preset ogm.
pin
clock answer
page
If the REC TIME/ANN/4/1
switch is set to Announce
Only, then the preset
message “Hello. No one is
available to take your
call” is played.
A tone will sound, and you hear the preset
message “Hello. No one is available to
take your call, please leave a message
after the tone” on the Base Unit speaker.
mic
✃
21
Download from Www.Somanuals.com. All Manuals Search And Download.
A second tone sounds after the preset message plays, and the Answering
System automatically returns to Standby.
3. To select your recorded message again, press ogm.
The preset message will begin to play on the Base Unit speaker.
4. While the preset message is playing, press ogm again.
A tone will sound, and your recorded message will play on the base Unit
speaker. A second tone sounds after your message plays, and the Answering
System automatically returns to Standby.
Setting the Toll Saver Switch
The switch allows you to set the number of
rings the caller hears before your Answering
System answers. You can set the switch to
answer after 2 rings or after 4 ring. In the TS
(Toll Saver) position, the Answering System
answers after two rings if you have messages
recorded, and it answers after four rings if
there are no new messages. So if you call
long distance to check your messages, you
can hang up after the second ring and not be billed.
For the New Zealand Model,
when in the TS (Toll Saver)
position, the answering
system answers after six (6)
rings if there are messages
and nine (9) rings if there
are no new messages.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing New Messages
When the Message Counter LED flashes, you have received new messages.
status
1. Press play/stop
The message is announced first, then the Day and
delete
play/stop
Time stamp afterwards. The message Counter LED
displays the number of the message playing.
Ø
repeat ogm
memo
skip
Note: If you want to stop reviewing your messages
press the play/stop
again.
2. When all messages have played, a long tone sounds.
3. After the previous announcement another tone sounds, indicating the system
has automatically returned to Standby.
The message counter LED stops flashing, indicating that all of the new
messages have been reviewed and stored.
4. The talk/batt low LED goes off.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeating a Message
Base Operation
1. Press play/stop
2. Press repeat
status
to review your messages.
at anytime to replay a
message.
delete
play/stop
skip
Ø
Note: Pressing repeat during a message returns the
systems to the beginning of that message.
Pressing repeat again before the message
replays causes the system to scan back one
repeat ogm
memo
message. If you have several messages, press repeat until you return to the
message you want to replay.
3. Press play/stop
Standby.
at anytime to stop reviewing messages and return to
Note: The system will automatically return to Standby if all the messages have been
played.
Skipping a Message
Base Operation
status
1. Press play/stop
to review your messages.
2. Press skip
at anytime to skip to the next
message.
delete
play/stop
skip
Ø
Note: Each time skip is pressed, the system scans
forward one message. If you have several
messages, press skip until you get to the message
you want to play.
repeat ogm
memo
3. Press play/stop
at anytime to stop reviewing messages and return to
Standby.
4. When all messages have played, a long beep sounds. Then the system
automatically returns to Standby.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Message
Base Operation
1. Press play/stop
to review your messages.
status
2. If you decide to delete a message, press and
Ø
release delete
anytime during the message.
delete
play/stop
skip
The system beeps and immediately goes to the
next message.
Ø
repeat ogm
memo
Note: When you press delete you are deleting the
message. Once the message is deleted, it cannot
be replayed.
3. You will hear a long tone on the Base speaker.
Deleting all Messages
You can delete all your messages without deleting each separate message. To
delete all the messages, you must use the delete button on the Base Unit.
Ø
status
1. Press and hold delete
for at least 3 seconds
2. A long tone sounds once the messages are erased.
delete
play/stop
skip
Ø
repeat ogm
memo
Message Full Indication
The XSA660 or XSA650 has a maximum record time of 15 minutes or up to 59
incoming message. When the memory is full, the Answering System will not record
incoming calls. To return the system to normal operation, follow these steps.
1. When the memory is full, the phone will ring 15 times before the
announcement “No remaining time” plays.
2. You must review your messages and then delete some or all of the stored
messages.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Screening Incoming Calls
If you receive a call while your Answering System is on, you can listen to the
incoming message on the Base Unit speaker. If you decide to answer the call,
1. Press speaker on the Base or pick up the Handset.
Note: The Answering System stops recording the
speaker
incoming message when speaker is pressed.
2. When you finish the call, press speaker to
hang up on the base or Talk on the handset or
hangup the handset.
volume
✃
✃
Leaving a Memo Message
You can use the XSA660 or XSA650 to leave a Memo Message for someone else
who uses your Answering System.
status
1. To record your Memo Message, press and hold
memo until you hear a long tone and the
Message Counter LED displays [--].
2. Speak into the microphone. When you are
delete
play/stop
skip
Ø
repeat ogm
memo
finished recording, press play/stop.
There is a tone, and the Message Counter LED
shows the total number of messages stored in
memory.
3. After you have recorded your message, the system returns to Standby.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operation
You can operate your XSA660 or XSA650 you’re away from home by calling from any
touch-tone phone. When using this feature, remember these important guidelines.
• You should change your Personal Identification Number (PIN) before using
your phone. When you first apply power, the code is set to 80.
• You cannot change the Time and Day Stamp or your PIN code from a touch-
tone phone.
Setting Your PIN Code
Using the phone, you can set a personal two digit code (00 to 99) for your PIN
code. You must use your PIN code to access your Answering System from a touch-
tone telephone.
repeat ogm
memo
skip
1. Press and hold pin. The [00] display on the Base.
2. Press skip or repeat to select the
pin
clock answer
page
first digit of four pin numbers.
3. Press pin again.
4. Press skip
or repeat
to select the next digit of your pin
number.
5. Press pin again.
You will hear a long tone which indicates that the new code is saved.
Using a Touch-Tone Phone
You can operate your Answering System using
any touch-tone phone. Use this function to
check for recorded messages, play or delete
messages, or even record a new outgoing
message.
Function
Repeat
Press
#1
Play Message
Skip
#2
#3
Delete Message
Stop
#4
1. Call your telephone number.
#5
2. During the outgoing message playback,
press # followed by your PIN number.
Answer ON
#6
3. The Answering System announces the Time
and Day Stamp. The number of messages
stored in memory follows.
Memo Rec/Memo Rec Stop #7
Ogm Rec/ogm Rec Stop #8
Remember to press # before
each command number.
Answer OFF
#9
4. Use this chart to select the function you
want.
Room Monitor
#,*
Note: You must enter a command within 2 seconds or the Answering System hangs
up and returns to Standby.
5. When you’ve finished, hang up to exit the system.
Your Answering System automatically returns to Standby.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
If your XSA660 or XSA650 Integrated Telephone Answering Device is not
performing to your expectations, please try these simple steps. If you are still
unable to resolve the problems, contact Uniden Customer Service for assistance.
Caution: Do not attempt to service this until yourself. Servicing must be performed by
qualified personnel.
PROBLEM
SUGGESTION
✃
Make sure the AC adaptor is plugged into the base and
wall outlet.
Charge light won’t
come on when
handset is placed
in base.
✃
✃
Make sure the handset is properly seated in base.
Make sure the charging contacts on the handset and base
are clean. See page 14
✃
✃
Make sure that the base antenna is fully extended in the
vertical position.
The audio sounds
weak and/or
scratchy.
Interference by other electronics equipment such as TVs.
Computers microwaves etc.
✃
✃
You may have gone too far from the base.
Press the chan key to search for clearer reception.
✃
✃
✃
✃
Check both ends of the base telephone line cord are
plugged in fully.
Make sure the AC adaptor is plugged into the base and
wall outlet.
Can’t make or
receive calls.
Disconnect the AC adaptor for a few minutes, then
reconnect it.
Reset security code by placing the handset back on the
base for a few seconds. The status LED will blink
indicating that the phone has been reset.
✃
The Nickel-Cadmium battery pack may be weak.
Charge the battery for 15-20 hours.
✃
✃
✃
The handset may be too far away from the base.
The handset
doesn’t ring or
receive a page.
Place the base away from appliances or metal objects.
Reset security code by placing the handset back on the
charging cradle for a few seconds. The status LED will
blink indicating that the phone has been reset.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
Base Unit
SUGGESTION
✃
Set the Base Unit Ringer switch to ON.
doesn’t ring
✃
✃
✃
Make sure the base unit is plugged in.
Make sure the Answering System is turned ON.
Disconnect the AC adaptor to reset the phone.
Answering System
does not work.
✃
✃
Set the REC TIME/ANN/4/1 switch in either the 4-minute
or 1-minute position.
Answering System
does not
answer calls.
The memory may be full. Delete some or all of the saved
messages.
✃
✃
The incoming messages may be too long. Remind callers
to leave a brief message.
Message are
incomplete.
The memory may be full. Delete some or all of the saved
messages.
✃
The answering machine has a flash memory with no
battery backup. Record your personal outgoing message
again. The incoming messages should still remain.
After a power
failure, the outgoing
message is deleted.
✃
✃
There has been a power failure. Press Reset to reset the
Answering System.
Message counter
LED flashes 88
Adjust the volume control on the Base Unit
No sound on the
Base Unit Speaker
✃
✃
Make sure you’re using the correct PIN code.
Cannot access
remote call-in
feature from another
touch-tone phone
Make sure that the touch-tone phone you’re using can
transmit the tone for at least two seconds. If it cannot, you
may have to change to another phone
✃
✃
The memory may be full. Delete some or all of the saved
messages
Cannot record
outgoing message
The power to the base unit has been interrupted. Reset the
clock as detailed on page 21 of this owner’s manual.
Clock losses time
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL
Frequency Control:
PLL
FM
Modulation:
Operating Temperature: -10˚C to 50˚C
BASE UNIT
Receive Frequency:
39.775 to 40.00 MHz (10 channels AUS)
39.800 to 40.450 MHz (25 channels NZ)
Transmit Frequency: 30.075 to 30.300 MHz (10 channels AUS)
30.100 to 30.750 MHz (25 channels NZ)
Power requirements: 230V/240V AC 50 Hz
Size (without antenna): 175mm (W) x 52mm (H) x 210mm (D)
Weight:
Approx. 667g
HANDSET
Receive Frequency:
30.075 to 30.300 MHz (10 channels AUS)
30.100 to 30.750 MHz (25 channels NZ)
Transmit Frequency: 39.775 to 40.000 MHz (10 channels AUS)
39.800 to 40.450 MHz (25 channels NZ)
Power requirements: Rechargeable Ni- Cd battery pack (BT434)
Size (without antenna): 52mm (W) x 178mm (H) x 33mm (D)
Weight:
Battery:
Approx. 353g (including battery)
BT-434
Capacity
Talk mode
300 mAH, 3.6V x 3 (AAA size)
6 hours
Standby mode 10 days
ANSWERING SYSTEM
Memory Type
Digital Tapeless Recording
Memory Capacity
Message Length
15 min. (nominal) (59 messages)
1 min. or 4 min. incoming message (max.)
30 sec. outgoing message (max.)
Specifications, features and availability of optional accessories
are all subject to change without prior notice.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
One Year Limited Warranty
Important:
Warrantor:
Evidence of original purchase is required for warranty service.
Uniden Australia Pty Limited ACN 001 865 498
Uniden New Zealand Limited
ELEMENT OF WARRANTY: Uniden warrants to the original retail owner for the duration
of this warranty, its XSA650/660 (herein after referred to as the Product), to be free from
defects in materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original retail owner only, shall terminate
and be of no further effect 12 months after the date of original retail sale. This warranty will
be deemed invalid if the product is; (A) Damaged or not maintained as reasonable and
necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any
configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone
other than an authorised Uniden Repair Agent for a defect or malfunction covered by this
warranty, (E) Used in conjunction with any equipment or parts or as part of a system not
manufactured by Uniden. This warranty is only valid in the original country of purchase.
PARTS COVERED: This warranty covers for one (1) year, the Base Unit and Handset only.
All accessories (eg. AC Adaptor etc.)are covered for 90 days only.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, the warrantor at its discretion, will
repair the defect or replace the product and return it to you without charge for parts or
service. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT
OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN
ADDITION TO AND DOES NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE
CONSUMER GUARANTEE ACT.
WARRANTY CARD: If a warranty card has been included with this product then please
fill it in and return to us within 14 days of purchase. Your name and the Serial number of
the product will then be registered in our database and this will help us process your claim
with greater speed and efficiency should you require warranty service.
PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY: In the event that
the product does not conform to this warranty, the Product should be shipped or delivered,
freight pre-paid, with evidence of original purchase (eg. a copy of the sales docket), to the
warrantor at:
UNIDEN AUSTRALIA PTY LIMITED
SERVICE DIVISION
345 Princes Highway,
UNIDEN NEW ZEALAND LIMITED
SERVICE DIVISION
150 Harris Road,
Rockdale NSW 2216
Ph (02) 9599 3577 Fx (02) 9599 3278
Toll Free 1300 366 895
East Tamaki, Auckland
Ph (9) 273 8383 Fx (9) 274 4253
Toll Free 0800 4 UNIDEN
4 864 336
Customers in other States should ship or deliver the Product freight pre-paid to their nearest
Uniden Authorised Repair Centre (Contact Uniden for the nearest Warranty Agent to you).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 Uniden Australia Pty Limited
Uniden New Zealand Limited
UDZZ01586ZZ
Download from Www.Somanuals.com. All Manuals Search And Download.
|