Toshiba DVD Player 24AF45C User Manual

2 4 AF4 5 C  
J3M60921A(E)_COVER  
1
12/01/2005, 10:20 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
Installation, Care, and Service  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
Installation  
Follow these recommendations and precautions and heed all  
warnings when installing your TV:  
4) Follow all instructions.  
16) Never modify this equipment. Changes or modifications  
may void: a) the warranty, and b) the users authority to  
operate this equipment under the rules of the Federal  
Communications Commission.  
5) Do not use this apparatus near  
water.  
17)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY, DEATH, OR EQUIPMENT  
DAMAGE! Never place the TV on  
6) Clean only with a dry cloth.  
an unstable cart, stand, or table. The TV  
may fall, causing serious personal injury,  
death, or serious damage to the TV.  
7) Do not block any ventilation  
openings. Install in accordance with  
the manufacturers instructions.  
18) Never place or store the TV in direct  
sunlight; hot, humid areas; areas  
subject to excessive dust or vibration;  
or locations with temperatures at or  
below 41°F (5°C).  
8) Do not install near any heat  
sources such as radiators,  
heat registers, stoves, or other  
apparatus (including amplifiers)  
that produce heat.  
9) Do not defeat the safety purpose of the polarized or  
grounding type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has  
two blades and a third grounding  
19) Always place the TV on the floor  
or a sturdy, level, stable surface that  
can support the weight of the unit.  
Wide plug  
prong. The wide blade or the third  
prong are provided for your safety.  
If the provided plug does not fit into  
your outlet, consult an electrician  
for replacement of the obsolete outlet.  
20) Never place items such as vases,  
aquariums, or candles on top of the TV.  
10) Protect the power cord from being  
walked on or pinched, particularly at  
plugs, convenience receptacles, and  
the point where it exits the apparatus.  
11) Only use attachments/accessories specified by the  
21) Never block or cover the slots or  
openings in the TV cabinet back,  
bottom, and sides. Never place  
the TV:  
manufacturer.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
on a bed, sofa, rug, or similar  
surface;  
too close to drapes, curtains,  
or walls; or  
apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
in a confined space such as a  
bookcase, built-in cabinet, or any  
other place with poor ventilation.  
The slots and openings are provided  
to protect the TV from overheating  
and to help maintain reliable  
operation of the TV.  
13) Unplug this apparatus during  
lightning storms or when  
unused for long periods  
of time.  
14) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power supply  
cord or plug is damaged, liquid has  
22) Never allow anything to rest on or roll over the power  
cord, and never place the TV where the power cord is  
subject to wear or abuse.  
been spilled or objects have fallen into  
the apparatus, the apparatus has been  
exposed to rain or moisture, does not  
operate normally, or has been dropped.  
QUALIFIED  
SERVICE  
TECHNICIAN  
23) Never overload wall outlets and  
extension cords.  
15)  
CAUTION: To reduce the risk of electric shock, do  
not use the polarized plug with an extension cord,  
receptacle, or other outlet unless the blades can  
be inserted completely to prevent blade exposure.  
0303  
3
3
J3M60921A(E)_P02-06  
3
12/01/2005, 10:21 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30) [This item applies to projection TVs only.] If the air  
temperature rises suddenly (for example, when the TV is  
first delivered), condensation may form on the lenses. This  
can make the picture appear distorted or the color appear  
faded. If this happens, turn off the TV for 6 to 7 hours to  
allow the condensation to evaporate.  
24) Always operate this equipment from  
a 120V AC, 60 Hz power source only.  
31) For added protection of your TV from lightning and power  
surges, always unplug the power cord and disconnect the  
antenna from the TV if you leave the TV unattended or  
unused for long periods of time.  
25) Always make sure the antenna system is properly  
grounded to provide adequate protection against voltage  
surges and built-up static charges (see Section 810 of the  
National Electric Code).  
Antenna lead-in wire  
32) During normal use, the TV may make  
occasional snapping or popping  
Antenna discharge unit  
(NEC Section 810-20)  
sounds. This is normal, especially  
Ground clamp  
when the unit is being turned on or  
off. If these sounds become frequent  
or continuous, unplug the power cord  
and contact a Toshiba Authorized Service Center.  
Grounding conductors  
(NEC Section 810-21)  
Electric service equipment  
Power service grounding  
33) Possible Adverse Effects on TV Picture Tube: If a fixed  
(non-moving) pattern remains on the TV screen for long  
periods of time, the image can become permanently  
ingrained in the picture tube and cause subtle but  
permanent ghost images. This type of damage is NOT  
COVERED BY YOUR WARRANTY. Never leave your TV  
on for long periods of time while it is displaying the  
following formats or images:  
electrode system (NEC Art 250 Part H)  
Ground clamps  
26)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY OR DEATH!  
Use extreme care to make sure you are never in  
a position where your body (or any item you are in contact  
with, such as a ladder or screwdriver) can accidentally  
touch overhead power lines. Never locate the antenna  
near overhead power lines or other electrical circuits.  
Never attempt to install any of the following during  
lightning activity:  
a) an antenna system; or b) cables, wires, or any home  
theater component connected to an antenna or phone  
system.  
Fixed Images, such as PIP/POP windows, stock tickers,  
video game patterns, TV station logos, closed captions,  
and websites.  
Special Formats that do not use the entire screen. For  
example, viewing letterbox style (16:9) media on a  
normal (4:3) display (gray bars at top and bottom of  
screen); or viewing normal style (4:3) media on a  
widescreen (16:9) display (gray bars on left and right  
sides of screen).  
Care  
Service  
34)  
For better performance and safer operation of your TOSHIBA  
TV, follow these recommendations and precautions:  
WARNING: RISK OF ELECTRIC  
SHOCK! Never attempt to service the  
TV yourself. Opening and  
27) Always sit approximately 1025 feet away from the TV and  
as directly in front of it as possible. The picture can appear  
dull if you sit too far to the left or right of the TV, or if  
sunlight or room lights reflect on the screen. Turn the TV  
off to check for reflections on the screen, and then remove  
the source of reflections while viewing the TV.  
removing the covers may expose  
you to dangerous voltage or other  
hazards. Refer all servicing to a  
Toshiba Authorized Service Center.  
QUALIFIED  
SERVICE  
TECHNICIAN  
35) If you have the TV serviced:  
Ask the service technician to use only replacement parts  
specified by the manufacturer.  
28) Always unplug the TV before  
cleaning. Never use liquid or  
aerosol cleaners.  
Upon completion of service, ask  
the service technician to perform  
routine safety checks to determine  
that the TV is in safe operating  
condition.  
36) When the TV reaches the end of its useful life, ask a  
qualified service technician to properly dispose of the TV.  
Improper disposal may result in a picture tube implosion  
and possible personal injury.  
29)  
WARNING: RISK OF ELECTRIC SHOCK!  
Never spill liquids or push objects of any kind  
into the TV cabinet slots.  
0303  
4
J3M60921A(E)_P02-06  
4
12/01/2005, 10:22 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information .......................................................................................... 2-4  
Welcome to Toshiba............................................................................................................ 6  
Exploring your new TV ................................................................................................................................6  
Selecting a location for the TV ....................................................................................................................6  
Connecting your TV ............................................................................................................ 7  
Connecting a VCR .......................................................................................................................................7  
Connecting a cable converter box ...............................................................................................................8  
Connecting a DVD player/satellite receiver and a VCR ..............................................................................9  
Connecting a DVD player with ColorStream® (component video) and a VCR............................................9  
Connecting two VCRs ...............................................................................................................................10  
Connecting a camcorder ...........................................................................................................................10  
Connecting an audio amplifier ...................................................................................................................10  
Using the remote control...................................................................................................11  
Preparing the remote control for use......................................................................................................... 11  
Installing the remote control batteries ....................................................................................................... 11  
Using the remote control to operate your other devices ........................................................................... 11  
Programming the remote control to operate your other devices...............................................................12  
VCR, DVD player, and cable TV converter codes.....................................................................................13  
Learning about the remote control ............................................................................................................14  
Setting up your TV ............................................................................................................ 15  
Changing the on-screen display language ................................................................................................15  
Adding channels to the TV’s memory........................................................................................................16  
Programming channels automatically ................................................................................................16  
Adding and erasing channels manually .............................................................................................16  
Changing channels ....................................................................................................................................16  
Using the TVs features .................................................................................................... 17  
Adjusting the channel settings...................................................................................................................17  
Switching between two channels .......................................................................................................17  
Programming your favorite channels .................................................................................................17  
Using the LOCK menu...............................................................................................................................18  
Selecting a PIN code ..........................................................................................................................18  
Locking channels ................................................................................................................................19  
Locking video input.............................................................................................................................20  
Setting the GameTimerTM ...........................................................................................................................20  
Labeling channels......................................................................................................................................21  
Setting the clock ........................................................................................................................................22  
Setting the ON/OFF timer ..........................................................................................................................22  
Setting the on timer ............................................................................................................................22  
Setting the off timer ............................................................................................................................23  
Adjusting the picture quality ......................................................................................................................24  
Watching video input .................................................................................................................................24  
Specifying the ColorStream® setting .........................................................................................................24  
Displaying on-screen information ..............................................................................................................24  
Setting the sleep timer ...............................................................................................................................25  
Using the closed caption feature ...............................................................................................................25  
Changing the picture size ..........................................................................................................................25  
Adjusting the sound ...................................................................................................................................26  
Muting the sound ................................................................................................................................26  
Selecting stereo/SAP broadcasts .......................................................................................................26  
Adjusting the sound quality ................................................................................................................27  
Using the BBE sound feature .............................................................................................................27  
Using the surround sound feature ......................................................................................................28  
Using the StableSound® feature .........................................................................................................28  
Auto power off............................................................................................................................................28  
Understanding the Power Return feature..................................................................................................28  
Appendix ............................................................................................................................ 29  
Troubleshooting .........................................................................................................................................29  
Specifications.............................................................................................................................................30  
Limited Warranty........................................................................................................................................31  
5
J3M60921A(E)_P02-06  
5
12/01/2005, 10:22 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Welcome to Toshiba  
Congratulations! You have purchased one of the finest color TVs on  
the market. The goal of this manual is to guide you through setting up  
and operating your Toshiba TV as quickly as possible.  
You may need to purchase other audio or video cables to connect your  
equipment. See Connecting your TVon page 7 for more information.  
Please read all the safety and operating instructions carefully before  
you begin.  
Exploring your new TV  
You can operate your TV by using the buttons on the front panel or the  
remote control. The front and back panels provide all the inputs you will  
need to connect other equipment to your TV.  
POWER  
TV  
VCR  
CABLE  
DVD  
POWER  
CHANNEL  
VOLUME  
1
4
7
2
5
8
3
6
9
+10  
VIDEO L/MONO  
VIDEO-3 IN  
AUDIO  
R
PHONES  
100  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
Remote  
sensor  
Channel  
Audio(L/R)/Video In  
Phones  
POWER  
Volume  
Power  
indicator  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
TV front panel  
RESET CAP/TEXT  
1/2  
16:9  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
FF  
REW  
PLAY  
TV/VCR  
REC  
STOP  
PAUSE/STILL  
VCR CH  
DVD SKIP  
IN  
OUT  
VIDEO  
CT-847  
Y
P
VIDEO  
ANT (75)  
B
R
L/MONO  
L/MONO  
AUDIO  
R
S-VIDEO  
AUDIO  
P
R
VIDEO 1  
VIDEO 2  
TV back panel  
Selecting a location for the TV  
Place the TV on the floor or on a sturdy platform in a location where  
light does not directly hit the screen.  
Place the TV far enough from the walls to allow proper ventilation.  
Inadequate ventilation may cause overheating, which may damage  
the TV.  
6
J3M60921A(E)_P02-06  
6
12/01/2005, 10:22 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting your TV  
A coaxial cable is the standard cable that comes in from your  
antenna or cable converter box. Coaxial cables use “F” connectors.  
Standard A/V (audio/video) cables are usually color coded accord-  
ing to use: yellow for video and red and white for audio. The red  
audio cable is for the stereo right channel, and the white audio  
cable is for the stereo left (or mono) channel. If you look at the rear  
panel of the TV, you will see that the terminals are color coded in  
the same manner as the cables.  
An S-video cable provides better picture performance than a  
standard video cable. S-video cables can only be used with S-video  
compatible components.  
Component video cables come in sets of three and provide the best  
picture performance. Component video cables can only be used  
with component video compatible components.  
NOTICE: RISK OF  
EQUIPMENT DAMAGE!  
Do not plug in any power cords  
until you have finished connecting  
all equipment.  
S-Video  
Cable  
ANTENNA  
Coaxial Cable  
AUDIO  
Cables  
Component video  
Cables  
VIDEO  
Cable  
Connecting a VCR  
This connection allows you to watch local channels and video programs,  
play or record on the VCR while watching TV, and record from one  
channel while watching another channel.  
You will need:  
two coaxial cables  
one set of standard A/V cables  
TV  
Note:  
IN  
OUT  
VIDEO  
Y
P
If using a mono VCR, connect L/Mono to  
VCR Audio OUT using only one audio cable.  
For better picture quality, if your VCR has  
S-video, you can use an S-video cable  
instead of the standard video cable. Do not  
connect a standard video cable and an  
S-video cable to VIDEO1 simultaneously.  
VIDEO  
ANT (75)  
B
R
L/MONO  
L/MONO  
AUDIO  
R
S-VIDEO  
AUDIO  
P
R
VIDEO  
1
VIDEO  
2
Cable Lead-in  
from cable box  
or antenna  
The unauthorized recording, use,  
distribution or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
Stereo VCR  
IN  
IN from ANT  
OUT to TV  
OUT  
CH  
CH  
3
4
L
R
VIDEO  
AUDIO  
7
J3M60921A(E)_P07-16  
7
18/01/2005, 3:37 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a cable converter box  
This television has an extended tuning range and can tune most cable  
channels without using a cable company supplied converter box. Some  
cable companies offer premium pay channelsin which the signal is  
scrambled. Descrambling these signals for normal viewing requires the  
use of a descrambler device, which is generally provided by the cable  
company.  
For Subscribers to Basic Cable TV Service  
For basic cable service not requiring a Converter/Descrambler box,  
connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack  
on the back of the television.  
For Subscribers to Scrambled Cable TV Service  
If you subscribe to a cable service that requires the use of a Converter/  
Descrambler box, connect the incoming cable to the Converter/  
Descrambler box and connect the output of the box to the Antenna  
Jack on the back of the television. Follow the connections shown  
below. Set the television to the output of the Converter/Descrambler  
box (usually channel 3 or 4) and use the Converter/Descrambler box to  
select channels.  
For Subscribers to Unscrambled Basic Cable with  
Scrambled Premium Channels  
If you subscribe to a cable service in which basic cable channels are  
unscrambled and premium channels require the use of a Converter/  
Descrambler box, you may wish to use a two-set signal splitter (some-  
times called a two-set coupler) and an A/B Switch box from the cable  
installer or an electronics supply store. Follow the connections shown  
below. With the switch in the Bposition, you can directly tune any  
nonscrambled channels on your TV. With the switch in the Aposition,  
tune your TV to the output of the Converter/Descrambler box (usually  
channel 3 or 4) and use the box to tune scrambled channels.  
Note:  
When you use a converter box with your TV,  
there may be features that you cannot  
program using the remote control, such as  
labeling channels, blocking channels, and  
programming your favorite channels.  
Incoming CATV  
IN  
OUT  
VIDEO  
Y
P
VIDEO  
ANT (75)  
Converter/Descrambler  
Converter/Descrambler  
B
R
L/MONO  
L/MONO  
AUDIO  
R
S-VIDEO  
AUDIO  
P
R
VIDEO  
1
VIDEO  
2
A
Splitter  
A/B Switch  
B
8
J3M60921A(E)_P07-16  
8
18/01/2005, 3:38 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DVD player/satellite receiver  
and a VCR  
This connection allows you to watch DVD/satellite, VCR, or TV  
programs. You can record from the satellite receiver and TV, as well as  
record one TV channel while watching another channel.  
You will need:  
three coaxial cables  
two sets of standard A/V cables  
one S-video cable  
one pair of standard audio cables  
To satellite  
DVD player/ Satellite Receiver  
Note:  
OUT  
L
You can use a standard video cable instead of  
the S-video cable, but the picture quality will  
decrease. If you use an S-video cable  
between the TV and DVD player/satellite  
receiver, make the audio connections only  
and remove the standard video cable.  
Satellite IN  
R
AUDIO  
S-VIDEO  
TV  
IN  
OUT  
O  
Y
P
VIDEO  
ANT (75)  
B
R
L/MON
L/MONO  
AUDIO  
R
S-VO  
DIO  
P
R
VIDEO  
1
VIDEO  
2
To antenna  
Stereo VCR  
IN  
IN from ANT  
OUT to TV  
OUT  
CH  
CH  
3
4
L
R
VIDEO  
AUDIO  
Connecting a DVD player with ColorStream®  
(component video) and a VCR  
This connection allows you to watch DVD, VCR, or TV programs and  
record TV programs. You can record from one source while watching a  
program from another source. Your TV is capable of using ColorStream  
(component video). Connecting your TV to a component video compatible  
DVD player, such as a Toshiba DVD player with ColorStream®, can  
greatly enhance picture quality and performance.  
You will need:  
two coaxial cables  
one set of standard A/V cables  
one set of component video cables  
one pair of standard audio cables  
Note:  
The ColorStream inputs on this TV are for use  
with devices that output 480i interlaced  
signals ONLY. This TV will not accept or  
display 480p or 720p progressive scan  
signals or 1080i interlaced high-definition  
signals. If you connect a high-definition set-  
top receiver, 480p progressive scan DVD  
player, or other similar device to the TV’s  
ColorStream inputs, YOU MUST SWITCH  
THE DEVICE’S OUTPUT TO 480i INTER-  
LACED MODE FIRST. Failure to do this will  
cause a poor picture or no picture to display.  
DVD player with ColorStream®  
OUT  
L
COLORSTREAMTM  
R
Y
Cb  
Cr  
AUDIO  
VIDEO  
OUT  
S-VIDEO  
TV  
IN  
OUT  
VIDEO  
Y
P
VIDEO  
ANT (75)  
B
R
L/MONO  
S-VIDEO UDIO  
L/MONO  
AUDIO  
R
P
The unauthorized recording, use,  
distribution or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
VIDEO  
1
VIDEO  
2
To antenna  
Stereo VCR  
IN  
IN from ANT  
OUT to TV  
OUT  
CH  
CH  
3
4
L
R
VIDEO  
AUDIO  
9
J3M60921A(E)_P07-16  
9
18/01/2005, 3:38 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting two VCRs  
You will need:  
two coaxial cables  
This connection allows you to record (dub/edit) from one VCR to  
another VCR.  
You will also be able to record from one TV channel while watching  
another channel.  
two sets of standard A/V cables  
Stereo VCR / Playback  
Note:  
To antenna  
Do not connect the same VCR to the output  
and input jacks on the TV at the same time.  
For better picture quality, if your VCR has  
S-video, you can use an S-video cable  
instead of the standard video cable. Do not  
connect a standard video cable and an  
S-video cable to VIDEO1 simultaneously.  
IN  
IN from ANT  
OUT to TV  
OUT  
CH  
CH  
3
4
VIO  
AUDIO  
TV  
IN  
OUT  
Y
VIDEO  
AN)  
P
P
B
R
L/MONO  
S-VIDEO AUDIO  
NO  
AUDIO  
R
R
VIDEO  
1
VIDEO  
2
Stereo VCR/ Recording  
IN  
IN from ANT  
OUT to TV  
OUT  
CH  
CH  
3
4
L
R
VIDEO  
AUDIO  
Connecting a camcorder  
This connection allows you to watch video materials recorded on a  
You will need:  
one set of standard A/V cables  
camcorder.  
Camcorder  
Note:  
AUDIO  
VIDEO  
For better picture quality, if your camcorder  
has S-video, you can connect an S-video  
(and standard audio cables) to VIDEO1 on  
the back of the TV. Do not connect a standard  
video cable and an S-video cable to VIDEO1  
simultaneously.  
L
R
OUT  
AUDIO  
VIDEO 3 LNO PHONES  
Front Panel of TV  
Connecting an audio amplifier  
This connection allows you to use an audio amplifier to enjoy high quality  
sound. This also allows you to use external speakers.  
You will need:  
one coaxial cable  
one pair of audio cables  
To control the audio, turn on the TV and the stereo amplifier.  
Audio Amplifier  
The unauthorized recording, use,  
distribution or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
AUDIO  
L
R
IN  
OUT  
TV  
To cable,  
cable box  
or antenna  
IN  
OUT  
VIDEO  
Y
VIDEO  
ANT (75)  
PB  
L/MONO  
L/MONO  
AUDIO  
R
S-VIDEO  
AUDIO  
PR  
2
R
VIDEO  
1
VIDEO  
10  
J3M60921A(E)_P07-16  
10  
18/01/2005, 3:38 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the remote control  
Preparing the remote control for use  
Note:  
With the remote control, you can operate your TV, most VCR and DVD  
player models, and cable TV converters together, even if they are  
different brands. If you will be using your TV with a Toshiba VCR or  
DVD player, your remote control is already programmed and ready to  
use. If you own different brands of VCRs, DVD players and/or convert-  
ers, you first have to program your remote control. (See Programming  
the remote control to operate your other deviceson page 12.)  
The TV remote control may not operate your  
VCR, DVD player, or cable TV converter.  
Refer to the owner's manual supplied with the  
applicable equipment to see which features  
may be available. Additionally, the remote  
control for this TV may not support certain  
features available on the original remote  
controls for such additional equipment, in  
which case, it is suggested that you use the  
original remote control for the applicable  
device.  
Installing the remote control batteries  
To install the batteries:  
1. Open the battery cover on the back of the remote control.  
Caution:  
Never throw batteries into a fire.  
Notes:  
Be sure to use AAA size batteries.  
Dispose of batteries in a designated  
disposal area.  
2. Install two AAAsize batteries. Match the + and signs on the  
Attention should be drawn to the environ-  
mental aspects of battery disposal.  
Do not mix different battery types or  
combine used batteries with new ones.  
If the remote control does not operate  
correctly, or if the operating range becomes  
reduced, replace both batteries with new  
ones.  
batteries to the signs on the battery compartment.  
If the batteries are dead or if you will not be  
using the remote control for a long time,  
remove the batteries to prevent battery acid  
from leaking into the battery compartment.  
3. Close the battery cover on the remote control until the lock snaps.  
Using the remote control to operate your other devices  
VCR  
To control a VCR:  
To control a DVD player:  
POWER  
POWER  
TV  
VCR  
CABLE  
DVD  
TV  
VCR  
CABLE  
Program the remote  
control to recognize the  
brand of your DVD  
player (see  
Programming the  
remote control to  
operate your other  
deviceson page 12).  
The buttons shown at  
right will then control the  
DVD player. Press the  
DVD button first.  
Program the remote  
control to recognize  
the brand of your VCR  
(see Programming the  
remote control to  
operate your other  
deviceson page 12).  
The buttons shown at  
right will then control  
the VCR. Press the  
VCR button first.  
Power  
DVD  
Power  
DVD  
1
4
7
2
5
8
3
6
9
1
4
7
2
5
8
3
6
9
+10  
+10  
100  
100  
Number  
buttons  
Channel  
Numbers  
0
0
+
+
CH  
CH  
DVD MENU  
L/M/  
/
VOL  
VOL  
+
VOL  
VOL  
+
MENU/  
ENTER  
MENU/  
ENTER  
Enter  
Channel +/–  
CH  
CH  
TOP Menu  
Volume  
L/M (TV)  
DVD Clear  
Display  
Fast Forward  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
CH RTN  
VOL  
FAV  
VOL  
FAV  
RESET CAP/TEXT  
1/2  
16:9  
RESET CAP/TEXT  
1/2  
16:9  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
Fast Forward  
CODE  
MTS  
SLEEP  
MUTE  
FF  
CODE  
MTS  
SLEEP  
MUTE  
FF  
Play  
Play  
Rewind  
REW  
PLAY  
REW  
PLAY  
Rewind  
DVD Menu  
TV/VCR  
REC  
STOP  
PAUSE/STILL  
TV/VCR  
REC  
STOP  
PAUSE/STILL  
TV/VCR  
Record  
VCR CH  
VCR CH  
DVD SKIP  
DVD SKIP  
Stop  
Stop  
DVD Skip  
/
VCR CH L/M  
Pause/Still  
Pause/Still  
11  
J3M60921A(E)_P07-16  
11  
18/01/2005, 3:39 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CABLE  
Power  
To control a cable TV  
converter:  
POWER  
TV  
VCR  
CABLE  
DVD  
Program the remote  
control to recognize the  
brand of your converter  
(see Programming the  
remote control to operate  
your other devices”  
below). The buttons  
shown at right will control  
the cable TV converter.  
Press the CABLE button  
first.  
1
4
7
2
5
8
3
6
9
+10  
100  
Channel  
Numbers  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
Channel +/–  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
CH RTN  
VOL  
FAV  
RESET CAP/TEXT  
1/2  
16:9  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
FF  
REW  
PLAY  
TV/VCR  
REC  
STOP  
PAUSE/STILL  
VCR CH  
DVD SKIP  
VCR  
POWER  
TV  
VCR  
CABLE  
DVD  
Programming the remote control to operate  
your other devices  
This remote control is pre-programmed to operate Toshiba VCRs and  
DVD players. To control VCRs, DVD players, or cable converters other  
than Toshiba models, you must follow the steps below to program your  
remote control.  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
+10  
100  
0
+
CH  
1. While holding down the CODE button, press the button for the  
device you want to control (VCR, DVD, or CABLE).  
2. Enter the 2-digit code listed on page 13 using the Number buttons  
(09) within 10 seconds.  
3. Point the remote control at the VCR, DVD player, or converter and  
press POWER to test the code.  
VOL  
VOL  
+
MENU/  
ENTER  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
If the VCR, DVD player, or converter turns on, you have entered  
the right code.  
16:9  
RESET CAP/TEXT  
1/2  
If the VCR, DVD player, or converter does not respond to the  
remote control, you may have entered the wrong code. Repeat  
steps 1 and 2 using another code.  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
FF  
Code  
REW  
PLAY  
Notes:  
For future reference, write down the codes you used:  
VCR code ________________________  
DVD player code ___________________  
Cable TV converter code ____________  
When shipped from the factory, the remote  
control is set to operate your TV.  
If you do not enter the code within 10  
seconds from step 1 or if you enter a code  
not listed on page 13, this operation is  
canceled.  
Each time you replace the batteries, you  
must reprogram the remote control.  
Some newer VCRs are capable of working  
on either of two remote codes. These VCRs  
have a switch labeled VCR1/VCR2.”  
If your VCR has this kind of switch and  
does not respond to any of the codes for  
your VCR, set the switch to the other  
position (VCR1 or VCR2) and reprogram  
the remote control.  
12  
J3M60921A(E)_P07-16  
12  
18/01/2005, 3:39 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR, DVD player, and cable TV converter codes  
VCR  
Admiral  
Adventura  
Aiwa  
Akai  
Audio Dynamics  
Bell & Howell  
Broksonic  
Canon  
Citizen  
Craig  
08, 61  
31  
31  
23, 38, 41  
02, 18  
06, 47  
21, 26, 33, 50, 55  
14  
09  
12  
14, 59  
44, 46, 48, 54  
36, 46  
02, 18  
03, 21 23, 26, 33, 35, 43, 50  
11, 12, 13, 47  
31  
14, 16, 20  
09  
56, 62, 63  
15, 57  
14, 27  
14, 15, 18, 27  
02, 25, 58  
02  
39  
09, 31  
07, 14, 31  
07, 18  
09  
06, 12, 14, 31, 33  
04, 22, 52, 64  
08, 14, 16, 19, 31, 49  
Multi Tech  
NEC  
Orion  
Panasonic  
Pentax  
39  
02, 18  
33, 50  
14, 51, 59  
15  
07, 14  
07, 14, 27  
10, 15  
46  
16, 60  
14, 59  
15, 16, 20, 27, 40, 42, 60  
06, 08, 12, 14, 31  
20, 30  
39  
06, 12, 47  
04, 05, 33, 43  
06, 09, 11, 12, 15  
08, 61  
39  
08, 14, 16, 19, 31, 49  
17, 32, 37  
07, 14, 27  
31  
09  
02  
02, 31  
34  
05, 15  
39  
04, 18  
02, 18  
01, 24, 25, 29, 37  
Philco  
Philips  
Pioneer  
Portland  
Pro Scan  
Quasar  
RCA  
Realistic  
Samsung  
Sansui  
Sanyo  
Scott  
Sears  
Sharp  
Shintom  
Signature 2000  
Sony  
Sylvania  
Symphonic  
Tashiko  
Tatung  
Curtis Mathes  
Daewoo  
Daytron  
DBX  
Emerson  
Fisher  
Funai  
General Electric  
Goldstar  
Go Video  
Hitachi  
Instant Replay  
J.C. Penney  
JVC  
Kenwood  
Logik  
LXI  
Magnavox  
Marantz  
Marta  
Memorex  
Mitsubishi  
Montgomery Ward  
Teac  
Teknika  
Toshiba  
XR1000  
Vector Research  
Yamaha  
Zenith  
DVD PLAYER  
Aiwa  
Apex  
23  
20  
RCA  
Saba  
01,06  
01  
Denon  
00, 17  
01  
11  
Sampo  
Samsung  
Sharp  
Silvania  
SMC  
14  
10  
08  
32, 18  
25  
04, 26, 27, 28  
00  
01  
03  
22  
00, 30  
07, 12  
31  
Ferguson  
Hitachi  
JVC  
Kenwood  
Konka  
Mitsubishi  
Nordmende  
Onkyo  
Oritron  
Panasonic  
Philips  
09  
15, 29  
19  
05  
01  
21  
24  
00  
03, 16  
02  
13  
Sony  
Technics  
Thomson  
Toshiba  
Wave  
Yamaha  
Zenith  
Vialta  
Pioneer  
Raite  
Funai  
32, 18  
CABLE TV CONVERTER  
Allegro  
Allegro A/B Switch  
Gemini  
General Electric  
General Instrument  
Hamlin  
Jerrold  
Kale Vision  
Macom  
58, 62  
61  
05, 31, 38  
67  
05, 06  
02, 03, 45, 65, 66  
04, 07, 08, 09, 10, 18, 60, 63  
35  
RCA DSS  
Regency  
Samsung  
Scientic Atlanta  
Sprucer  
Standard Comp  
Texscan  
Tocom  
73  
29  
35  
16, 23, 36, 64  
13  
35  
39, 56, 71  
17, 18, 46  
48, 62  
44  
58, 62  
40  
49  
54, 55, 72  
01, 53, 74  
12, 28, 30, 51  
14, 21  
Unika  
Magnavox  
NSC  
Oak  
Panasonic  
Paragon  
Philips  
34  
35, 39, 68, 69, 70  
11, 32, 42  
13, 20  
33  
United Satellite  
Universal  
Vid Tech  
Video Way  
Viewstar  
47, 50, 52, 54, 55  
15, 43  
Zenith  
Zenith Satellite  
Pioneer  
13  
J3M60921A(E)_P07-16  
13  
18/01/2005, 3:39 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Learning about the remote control  
POWER turns the TV on and off  
SLEEP programs the TV to turn off at a set time (page 25)  
TV/VIDEO selects the video input source (page 24)  
CH + / cycles through programmed channels (page 16)  
TV/VCR/CABLE/DVD  
TV/VCR/CABLE/DVD select TV, VCR, Cable, or DVD mode (page 11)  
CHANNEL NUMBERS allow direct access to channels (page 16)  
VOLUME + / adjusts the volume level  
POWER  
TV  
VCR  
CABLE  
DVD  
POWER  
1
4
7
2
5
8
3
6
9
+10  
Channel  
Numbers  
100  
CH RTN (Channel Return) returns to the last viewed channel (page 17)  
MENU/ENTER allows access to programming menus, and sets pro-  
grammed menu information (page 15)  
0
+
CH  
Menu/Enter  
CH +/–  
FAV L/ M (Favorite Channels) cycle through favorite channels (page 17)  
RESET returns settings to preset factory formats (pages 24 and 27)  
CAP/TEXT turns closed captions or text on and off (page 25)  
VOL  
VOL  
+
MENU/  
ENTER  
Recall  
Exit  
Volume +/–  
CH  
TV/Video  
Volume M/L (DVD)  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
1/2 selects closed caption/text channel 1 or 2 (page 25)  
FAV L/M(Favorite  
Channels)  
CH RTN (Channel  
Return)  
Closed  
Captioning  
VOL  
FAV  
MUTE turns off the sound (page 26)  
16:9  
RESET CAP/TEXT  
1/2  
Reset  
MTS switches among STEREO, SAP, and MONO sound (page 26)  
RECALL displays status information on-screen (page 24)  
CODE is used to program the remote control (page 12)  
EXIT closes on-screen menus (page 15)  
16:9  
Display (DVD)  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
DVD Menu  
TOP Menu  
DVD Clear  
Code  
MTS  
CODE  
MTS  
SLEEP  
MUTE  
FF  
Mute  
Sleep  
FF  
REW  
PLAY  
Rew  
Play  
TV/VCR  
REC  
STOP  
PAUSE/STILL  
Pause/Still  
TV/VCR  
Rec  
16:9 toggles the aspect ratio between 4:3 (letterbox) and 16:9 (wide  
VCR CH  
screen) modes (page 25)  
VCR Channel  
LM/DVD Skip  
DVD SKIP  
Stop  
STOP stops a videotape/DVD  
REC starts recording a videotape  
PLAY plays a videotape/DVD  
FF fast forwards a videotape/DVD  
REW rewinds a videotape/DVD  
PAUSE/STILL pauses a videotape/DVD  
TV/VCR toggles between TV and VCR modes when viewing while  
recording  
VCR CHANNEL  
DVD SKIP  
L
and  
M
cycle through programmed VCR channels  
skips DVD chapter  
DISPLAY displays DVD status information on-screen  
VOLUME L/M (DVD) adjust the DVD volume level  
DVD CLEAR clears input data in DVD mode  
TOP MENU accesses the DVD TOP menu  
DVD MENU accesses the DVD menu  
14  
J3M60921A(E)_P07-16  
14  
18/01/2005, 3:40 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
After you have installed the batteries and programmed the remote  
control, you need to set some preferences on the TV using the menu  
system. You can access the menu system with the buttons on the  
remote control.  
When you make a menu selection, your changes occur immediately.  
You do not have to press MENU or EXIT to see your changes.  
After five seconds, the menu screen will automatically close if you  
do not make a selection. Your changes will still be saved.  
When you are finished programming the menus, press EXIT.  
Changing the on-screen display language  
You can choose from three different languages (English, French, and  
Spanish) for the on-screen display of adjustment menus and  
messages.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
+10  
100  
To select a language:  
1. Press MENU, then press or until the OPTION menu appears.  
0
+
CH  
VOL  
VOL  
+
CH  
MENU/  
ENTER  
PICTURE AUDIO SETUP OPTION  
Menu  
Exit  
LANGUAGE  
ENGLISH  
CH LABEL  
FAVORITE CH  
LOCK  
ON/OFF TIMER  
COLORSTREAM DVD  
START  
START  
START  
OFF  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
SELECT  
ADJUST  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
2. Press L or M to highlight LANGUAGE.  
CH  
PICTURE AUDIO SETUP OPTION  
LANGUAGE  
ENGLISH FRANCAIS  
ESPANOL  
CH LABEL  
FAVORITE CH  
LOCK  
START  
START  
START  
OFF  
ON/OFF TIMER  
COLORSTREAM DVD  
SELECT  
ADJUST  
3. Press or to highlight your desired language.  
15  
J3M60921A(E)_P07-16  
15  
18/01/2005, 3:40 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adding channels to the TVs memory  
When you press CH +/- on the remote control or CHANNEL M/L on  
the TV front panel, your TV will stop only on the channels stored in the  
TVs channel memory. Follow the steps below to program channels into  
the memory.  
Programming channels automatically  
Your TV can automatically detect all active channels and store them in  
its memory. After the TV has stored the channels in its memory auto-  
matically, you can add or erase specific channels manually.  
POWER  
TV  
VCR  
CABLE  
DVD  
To add channels automatically:  
1. Press MENU, then press or to display the SETUP menu.  
2. Press L or M until the TV/CABLE  
selection is highlighted.  
1
4
7
2
5
8
3
6
9
+10  
100  
CH  
3. Press or to highlight either  
Channel  
Numbers  
PICTURE AUDIO SETUP OPTION  
TV or CABLE, depending on  
which you use.  
0
TV / CABLE  
TV CABLE  
START  
+
CH  
CH PROGRAM  
ADD / ERASE  
Channel +/–  
ADD  
VOL  
VOL  
+
If you use an antenna, choose TV.  
If you use cable, choose CABLE.  
MENU/  
ENTER  
Menu  
SELECT  
ADJUST  
CH  
4. Press M to select CH PROGRAM.  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
5. Press or to start channel programming. The TV will automati-  
cally cycle through all the TV or Cable channels (depending on  
which you selected), and store all active channels in the channel  
memory.  
VOL  
FAV  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
While the TV is cycling through the channels, the message  
PROGRAMMING NOW-PLEASE WAITappears.  
6. When channel programming is complete, the message COMPLETED”  
appears.  
CODE  
MTS  
SLEEP  
MUTE  
7. Press CH + or to view the programmed channels.  
Adding and erasing channels manually  
After you have programmed the channels automatically, you can add  
or erase specific channels manually.  
To add or erase channels manually:  
1. Select the channel you want to add or erase.  
If you are adding a channel, you must select the channel using the  
Channel Number buttons.  
2. Press MENU, then press or  
CH  
to display the SETUP menu.  
PICTURE AUDIO SETUP OPTION  
3. Press L or M to highlight ADD/  
TV / CABLE  
CABLE  
ERASE.  
CH PROGRAM  
ADD / ERASE  
START  
4. Press or to select ADD or  
ERASE, whichever function you  
want to perform.  
ADD ERASE  
SELECT  
ADJUST  
5. Repeat steps 14 for other  
channels you want to add or erase.  
Changing channels  
To change to the next programmed channel:  
Press CHANNEL M/L on the TV front panel or CH +/on the  
remote control.  
To change to a specific channel (programmed or unprogrammed):  
Press the Channel Number buttons (09 and 100) on the remote  
control.  
For example, to select channel 125, press 100, 2, 5.  
16  
J3M60921A(E)_P07-16  
16  
18/01/2005, 3:40 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TVs features  
Adjusting the channel settings  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
+10  
Switching between two channels  
You can switch between two channels without entering an actual  
channel number each time.  
100  
Channel  
Numbers  
0
+
CH  
To switch between two channels:  
1. Select the first channel you want to view.  
2. Select a second channel using the Channel Number buttons (09,  
100).  
VOL  
VOL  
+
MENU/  
ENTER  
3. Press CH RTN. The previous channel will be displayed.  
Each time you press CH RTN, the TV will switch back and forth  
between the two channels.  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
CH RTN  
16:9  
RESET CAP/TEXT  
1/2  
Programming your favorite channels  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
You can preset up to 12 of your favorite channels using the Favorite  
Channel Programming feature. Because this feature scans through  
only your favorite channels, it allows you to skip other channels you  
do not normally watch.  
CODE  
MTS  
SLEEP  
MUTE  
You can still use Channel + / to scan through all the channels you  
programmed in the TVs memory.  
To program your favorite channels:  
POWER  
TV  
VCR  
CABLE  
DVD  
1. Select a channel you want to program as a favorite channel.  
2. Press MENU, then press or to display the OPTION menu.  
3. Press L or M to highlight FAVORITE CH.  
1
4
7
2
5
8
3
6
9
+10  
100  
Channel  
Numbers  
CH  
0
PICTURE AUDIO SETUP OPTION  
+
CH  
LANGUAGE  
ENGLISH  
CH LABEL  
FAVORITE CH  
START  
START  
VOL  
VOL  
+
LOCK  
START  
MENU/  
ENTER  
ON/OFF TIMER  
OFF  
Menu/  
Enter  
COLORSTREAM DVD  
SELECT  
START  
CH  
Exit  
FAV  
FAV  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
4. Press or to display the FAVORITE CH menu. SET/CLEAR will  
be highlighted.  
VOL  
FAV  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
CH  
PICTURE AUDIO SETUP OPTION  
FAVORITE CH : CH 012  
SET/CLEAR  
SET UP CH  
SET CLEAR  
0
0
0
0
0
0
0
0
0
0
0
0
TV CABLE  
SELECT  
SET  
ENTER  
END  
EXIT  
5. Press or to highlight SET and press ENTER.  
6. Press EXIT to close the screen.  
7. Repeat steps 16 for up to 11 other channels.  
To select your favorite channels:  
Press the FAV L M buttons on the remote control to select your  
favorite channels.  
The FAV L M buttons will not work until you have programmed  
your favorite channels.  
17  
J3M60921A(E)_P17-26  
17  
18/01/2005, 3:41 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To clear your favorite channels:  
1. Select a channel you want to clear.  
POWER  
TV  
VCR  
CABLE  
DVD  
2. Press MENU, then press or to display the OPTION menu.  
3. Press L or M to highlight FAVORITE CH.  
4. Press or to display the FAVORITE CH menu. SET/CLEAR will  
be highlighted.  
1
4
7
2
5
8
3
6
9
+10  
100  
Channel  
Numbers  
0
+
CH  
CH  
PICTURE AUDIO SETUP OPTION  
VOL  
VOL  
+
MENU/  
ENTER  
FAVORITE CH : CH 012  
SET/CLEAR  
SET UP CH  
SET CLEAR  
Menu/  
Enter  
7
36  
4
1
12 125 63 40  
13 28 97 112  
TV CABLE  
SELECT  
CH  
SET  
ENTER  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
END  
EXIT  
VOL  
FAV  
Exit  
16:9  
RESET CAP/TEXT  
1/2  
5. Press or to highlight CLEAR.  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
CH  
PICTURE AUDIO SETUP OPTION  
FAVORITE CH : CH 012  
SET/CLEAR  
SET UP CH  
SET CLEAR  
7
36  
4
1
12 125 63 40  
13 28 97 112  
TV CABLE  
SELECT  
CLEAR  
ENTER  
END  
EXIT  
6. Press ENTER until “0” replaces the channel number you want to  
erase.  
7. Press EXIT to clear the screen.  
8. Repeat steps 1–6 for the other channels.  
Using the LOCK menu  
The LOCK menu includes the CH LOCK, VIDEO LOCK, GAMETIMER,  
and NEW PIN CODE functions.  
Selecting a PIN code  
You can use these functions after entering the correct PIN code.  
POWER  
TV  
VCR  
CABLE  
DVD  
To select your PIN code and access the LOCK menus:  
1. Press MENU, then press or to highlight the OPTION menu.  
2. Press L or M to highlight LOCK.  
1
4
7
2
5
8
3
6
9
+10  
100  
CH  
0
PICTURE AUDIO SETUP OPTION  
+
CH  
LANGUAGE  
ENGLISH  
CH LABEL  
FAVORITE CH  
LOCK  
START  
START  
START  
OFF  
VOL  
VOL  
+
MENU/  
ENTER  
ON/OFF TIMER  
Menu  
COLORSTREAM DVD  
SELECT  
START  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
3.Press or to display the BLOCKING menu.  
VOL  
FAV  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CH  
CODE  
MTS  
SLEEP  
MUTE  
PICTURE AUDIO SETUP OPTION  
LOCK  
BLOCKING  
PIN CODE  
RESET  
SET  
SELECT  
END  
ENTER  
[0-9]  
EXIT  
18  
J3M60921A(E)_P17-26  
18  
27/01/2005, 1:16 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Use the Channel Number buttons (09) to enter your PIN code.  
If you are accessing the LOCK menus for the first time, select a  
four-digit number to be your PIN code. Press ENTER. The  
BLOCKING menu appears.  
Note:  
If you forget your PIN code, press RECALL  
four times within five seconds from the  
BLOCKING menu. This allows you to proceed  
to the BLOCKING menu and resets your PIN  
code.  
CH  
PICTURE AUDIO SETUP OPTION  
LOCK  
POWER  
CH LOCK  
VIDEO LOCK  
START  
OFF  
TV  
VCR  
CABLE  
DVD  
OFF  
GAME TIMER  
NEW PIN CODE START  
1
4
7
2
5
8
3
6
9
SELECT  
ADJUST  
+10  
100  
Channel  
Numbers  
5. You may now enable blocking. See Locking channels(below),  
To change your PIN code(below), or Locking video input”  
(page 20), or Setting the GameTimer™” (page 20).  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
To change your PIN code:  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight LOCK.  
3. Press or to display the BLOCKING menu.  
4. Use the Channel Number buttons (09) to enter your PIN code.  
Press ENTER. The BLOCKING menu appears.  
5. Press L or M to highlight NEW PIN CODE and press or to  
display the NEW PIN CODE menu.  
Menu/  
Enter  
CH  
Recall  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
Exit  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
6. Use the Channel Number buttons (09) to enter a new code.  
Press ENTER.  
7. Press EXIT to return to normal viewing.  
Locking channels  
With the CH LOCK feature, you can lock specific channels. You will not  
be able to tune locked channels unless you clear the setting. You can  
choose to lock up to nine TV channels and nine cable channels.  
POWER  
TV  
VCR  
CABLE  
DVD  
To lock channels:  
1. Use the Channel Number buttons (09) to display the television  
channel you wish to lock.  
2. Press MENU, then press or to display the OPTION menu.  
3. Press L or M to highlight LOCK.  
1
4
7
2
5
8
3
6
9
+10  
100  
Channel  
Numbers  
0
+
CH  
4. Press or to display the LOCK menu.  
5. Use the Channel Number buttons (09) to enter your PIN code,  
then press ENTER. The LOCK menu appears.  
6. Press L or M to highlight CH LOCK and press or to display  
the CH LOCK menu.  
VOL  
VOL  
+
MENU/  
ENTER  
Menu/  
Enter  
CH  
7. Press or to select the following:  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
CH  
SETto set the channel as one to be  
VOL  
FAV  
PICTURE AUDIO SETUP OPTION  
Exit  
locked. Then press ENTER.  
CLEARto clear all channels from  
the list of locked channels.  
Then press ENTER.  
16:9  
RESET CAP/TEXT  
1/2  
LOCK  
CH LOCK  
VIDEO LOCK  
START  
OFF  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
OFF  
GAME TIMER  
NEW PIN CODE START  
SELECT ADJUST  
8. Repeat steps 1 through 7 to lock other  
channels. When you are finished  
locking channels, press EXIT to return  
to normal viewing.  
Note:  
CH  
After programming CH LOCK, change  
channels before turning off the television.  
PICTURE AUDIO SETUP OPTION  
If you try to tune a locked channel, the  
TV will not display it, but will display the  
nearest unlocked channel.  
CH LOCK : CH 12  
SET/CLEAR  
LOCKED CH  
SET CLEAR  
0
0
0
0
0
0
0
0
0
TV CABLE  
SELECT  
SET  
ENTER  
END  
EXIT  
19  
J3M60921A(E)_P17-26  
19  
18/01/2005, 3:41 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To unlock channels:  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight LOCK and then press or to display  
the LOCK menu.  
3. Use the Channel Number buttons (09) to enter your PIN code,  
then press ENTER. The LOCK menu appears.  
4. Press L or M to highlight CH LOCK and press or to display  
the CH LOCK menu.  
5. Press or to highlight CLEAR, and then press ENTER. This  
clears all channels from the list of locked channels.  
6. Press EXIT to return to normal viewing.  
Locking video input  
With the VIDEO LOCK feature, you can lock out the input sources  
(VIDEO1, VIDEO2, VIDEO3, COLORSTREAM) and channels 3 and 4.  
You will not be able to select the input sources with the TV/VIDEO  
button or Channel buttons unless you clear the setting.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
+10  
To set up the video lock:  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight LOCK.  
3. Press or to display the LOCK menu.  
4. Use the Channel Number buttons (09) to enter your PIN code,  
then press ENTER. The LOCK menu appears.  
5. Press L or M to highlight VIDEO LOCK.  
6. Press or to select:  
100  
Channel  
Numbers  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
Menu/  
Enter  
CH  
OFF: Unlocks all video input  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
CH  
sources.  
VIDEO: Locks VIDEO1, VIDEO2,  
VIDEO3 and COLORSTREAM.  
PICTURE AUDIO SETUP OPTION  
VOL  
FAV  
Exit  
LOCK  
16:9  
RESET CAP/TEXT  
1/2  
CH LOCK  
START  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
VIDEO +: Locks VIDEO1, VIDEO2,  
VIDEO3, COLORSTREAM, channel 3  
and channel 4. This option should be  
used if you use the antenna terminal to  
play a video tape.  
VIDEO LOCK  
OFF  
VIDEO VIDEO+  
OFF  
GAME TIMER  
NEW PIN CODE START  
SELECT ADJUST  
CODE  
MTS  
SLEEP  
MUTE  
Note:  
After programming VIDEO LOCK, change  
channels or activate the TV/VIDEO key before  
turning off the television.  
7. Press EXIT to return to normal viewing.  
Setting the GameTimerTM  
With the GameTimerTM feature, you can automatically activate the  
VIDEO LOCK feature (VIDEO setting) to set a time limit for playing a  
TV game (30, 60, 90 or 120 minutes).  
POWER  
TV  
VCR  
CABLE  
DVD  
To set up the GameTimer:  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight LOCK.  
3. Press or to display the LOCK menu.  
4. Use the Channel Number buttons (09) to enter your PIN code,  
then press ENTER. The LOCK menu appears.  
5. Press L or M to highlight GameTimer.  
6. Press or to select a time limit (30 minutes, 60 minutes, 90  
minutes, 120 minutes or OFF).  
1
4
7
2
5
8
3
6
9
+10  
100  
Channel  
Numbers  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
Menu/  
Enter  
7. Press EXIT to return to normal  
CH  
CH  
viewing. After the GameTimer is  
programmed, the display will appear  
briefly every ten minutes to remind you  
that the GameTimer is operating.  
When the programmed time is  
reached, the display will change the  
channel automatically.  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
PICTURE AUDIO SETUP OPTION  
VOL  
FAV  
LOCK  
Exit  
CH LOCK  
VIDEO LOCK  
START  
OFF  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
GAME TIMER  
OFF 30 60 90 120  
NEW PIN CODE START  
SELECT ADJUST  
CODE  
MTS  
SLEEP  
MUTE  
20  
J3M60921A(E)_P17-26  
20  
18/01/2005, 3:42 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Labeling channels  
Channel labels appear over the channel number display each time you  
turn on the TV, select a channel, or press the Recall button. You can  
choose any four characters to identify a channel.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
To create channel labels:  
1. Select a channel you want to label.  
2. Press MENU, then press or until the OPTION menu appears.  
3. Press L or M to highlight CH LABEL.  
+10  
100  
Channel  
Numbers  
0
+
CH  
CH  
VOL  
VOL  
+
PICTURE AUDIO SETUP OPTION  
MENU/  
ENTER  
LANGUAGE  
ENGLISH  
Menu/  
Enter  
CH LABEL  
FAVORITE CH  
LOCK  
START  
START  
START  
OFF  
CH  
ON/OFF TIMER  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
COLORSTREAM DVD  
VOL  
FAV  
SELECT  
START  
Exit  
16:9  
RESET CAP/TEXT  
1/2  
4. Press or to display the CH LABEL menu. SET/CLEAR will be  
highlighted.  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
CH  
PICTURE AUDIO SETUP OPTION  
CH LABEL : CH 12  
SET/CLEAR  
LABEL  
SET CLEAR  
SELECT  
END  
SET  
ENTER  
EXIT  
5. Press or to highlight SET.  
6. Press L or M to highlight LABEL.  
CH  
PICTURE AUDIO SETUP OPTION  
CH LABEL : CH 12  
SET/CLEAR  
LABEL  
SET  
SET  
SELECT  
ENTER  
END  
EXIT  
7. Press or to enter a character in  
the first space. Press the button  
repeatedly until the character you want  
appears on the screen. Press ENTER.  
8. Repeat step 7 to enter the rest of the  
characters.  
Note:  
CH  
The character will change as below.  
PICTURE AUDIO SETUP OPTION  
• • •  
• • •  
CH LABEL : CH 12  
0
9
A
SET/CLEAR  
LABEL  
SET  
A
+
Z
SPACE  
SELECT  
SET  
ENTER  
If you would like a blank space in the  
label name, you must choose a blank  
END  
EXIT  
space from the list of characters; otherwise, a dash will appear in  
that space.  
9. Repeat steps 18 for other channels. You can assign a label to  
each channel.  
10. Press EXIT to clear the screen.  
To erase channel labels:  
1. Select a channel with a label.  
2. Press MENU, then press or until the OPTION menu appears.  
3. Press L or M to highlight CH LABEL.  
4. Press or to display the CH LABEL menu.  
SET/CLEAR will be highlighted.  
5. Press or to highlight CLEAR.  
6. Press ENTER.  
7. Repeat steps 16 to erase other channel labels.  
21  
J3M60921A(E)_P17-26  
21  
18/01/2005, 3:42 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the clock  
You must set the clock before you can program the ON/OFF timer.  
POWER  
TV  
VCR  
CABLE  
DVD  
To set the clock: (Example: 8:30 AM)  
1. Press MENU, then press or to display the OPTION menu.  
1
4
7
2
5
8
3
6
9
2. Press L or M to highlight ON/OFF TIMER.  
+10  
100  
CH  
PICTURE AUDIO SETUP OPTION  
0
LANGUAGE  
ENGLISH  
+
CH  
CH LABEL  
FAVORITE CH  
LOCK  
START  
START  
START  
ON/OFF TIMER  
ON  
OFF SET  
VOL  
VOL  
+
MENU/  
ENTER  
COLORSTREAM DVD  
Menu/  
Enter  
SELECT  
SET  
ADJUST  
ENTER  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
3. Press or to highlight SET, then press ENTER. The ON/OFF  
TIMER menu appears.  
VOL  
FAV  
Exit  
16:9  
RESET CAP/TEXT  
1/2  
4. Press L or M to highlight CLOCK, then press or to highlight  
the hour position.  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CLOCK  
12:00 AM  
Note:  
ON TIMER  
12:00 AM  
CH 001  
CLEAR  
If the power source for the TV is interrupted  
(for example, the power cord is unplugged or  
a power failure occurs), you will need to reset  
the clock.  
OFF TIMER  
12:00 AM  
CLEAR  
SELECT  
END  
ADJUST  
EXIT  
5. Press L or M to set the hour, then press to highlight the minute  
position.  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CLOCK  
8:30 AM  
ON TIMER  
12:00 AM  
CH 001  
CLEAR  
OFF TIMER  
12:00 AM  
CLEAR  
SELECT  
END  
ADJUST  
POWER  
TV  
VCR  
CABLE  
DVD  
EXIT  
6. Press L or M to set the minutes, then press EXIT to return to  
1
4
7
2
5
8
3
6
9
normal viewing.  
+10  
100  
Setting the ON/OFF timer  
Setting the on timer  
This feature allows you to program the TV to turn on automatically at a  
set time. If you program the ON TIMER to DAILY,the TV will turn on  
every day at the same time to the same channel until you clear the ON  
TIMER.  
0
+
CH  
VOL  
VOL  
+
MENU/  
ENTER  
Menu/  
Enter  
To set the on timer: (Example: Turning on the TV to channel 12 at  
7:00 AM, DAILY)  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight ON/OFF TIMER.  
3. Press or to highlight SET, then press ENTER. The ON/OFF  
TIMER menu appears.  
VOL  
FAV  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
4. Press L or M to highlight ON TIMER and press or to highlight  
the hour position.  
Note:  
CH  
After a power failure or disconnection of the  
power, the timer settings will be lost.  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CLOCK  
12:00 AM  
ON TIMER  
12:00 AM  
CH 001  
CLEAR  
OFF TIMER  
12:00 AM  
CLEAR  
SELECT  
END  
ADJUST  
EXIT  
22  
J3M60921A(E)_P17-26  
22  
18/01/2005, 3:43 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.Press L or M to set the desired hour, then press  
.
POWER  
TV  
VCR  
CABLE  
DVD  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
1
4
7
2
5
8
3
6
9
CLOCK  
12:00 AM  
ON TIMER  
+10  
7:00 AM  
CH 001  
CLEAR  
100  
OFF TIMER  
12:00 AM  
CLEAR  
SELECT  
END  
ADJUST  
0
EXIT  
+
CH  
6.Set the desired minutes and channel, as in step 5.  
7. Press or to select ONCE or DAILY timer date.  
VOL  
VOL  
+
MENU/  
ENTER  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CH  
CLOCK  
12:00 AM  
ON TIMER  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
7:00 AM  
CH 012  
ONCE DAILY CLEAR  
OFF TIMER  
12:00 AM  
VOL  
FAV  
Exit  
CLEAR  
16:9  
RESET CAP/TEXT  
1/2  
SELECT  
END  
SET  
ENTER  
EXIT  
8. Press EXIT to return to normal viewing.  
Note:  
The ON TIMER has a one-hour automatic  
shut off. One hour after the ON TIMER has  
turned on the TV, the TV will turn off  
To cancel the on timer:  
Select CLEAR in step 7 above.  
Press EXIT to return to normal viewing.  
automatically unless you press any button .  
Setting the off timer  
This feature allows you to program the TV to turn off automatically at a set  
time. If you program the OFF TIMER to DAILY,the TV will automatically  
turn off every day at the same time.  
To set the off timer: (Example: Turning off the TV at 11:30 PM)  
1. Press MENU, then press or to display the OPTION menu.  
2. Press L or M to highlight ON/OFF TIMER.  
POWER  
TV  
VCR  
CABLE  
DVD  
3. Press or to highlight SET, then press ENTER.  
The ON/OFF TIMER menu appears.  
4. Press L or M to highlight OFF TIMER, then press or to  
highlight the hour position.  
1
4
7
2
5
8
3
6
9
+10  
100  
0
+
CH  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CLOCK  
12:00 AM  
VOL  
VOL  
+
ON TIMER  
MENU/  
ENTER  
7:00 AM  
CH 012  
DAILY  
Menu/  
Enter  
OFF TIMER  
12:00 AM  
CLEAR  
SELECT  
END  
ADJUST  
CH  
EXIT  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
5. Press L or M to set the desired hour, then press  
.
VOL  
FAV  
Exit  
16:9  
RESET CAP/TEXT  
1/2  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CLOCK  
12:00 AM  
CODE  
MTS  
SLEEP  
MUTE  
ON TIMER  
7:00 AM  
CH 012  
DAILY  
OFF TIMER  
11:00 PM  
CLEAR  
SELECT  
END  
ADJUST  
EXIT  
6. Set the desired minutes, as in step 5.  
7. Press or to select ONCE or DAILY.  
CH  
PICTURE AUDIO SETUP OPTION  
ON/OFF TIMER  
CLOCK  
12:00 AM  
ON TIMER  
7:00 AM  
CH 012  
DAILY  
OFF TIMER  
11:30 PM  
ONCE DAILY CLEAR  
SELECT  
END  
SET  
ENTER  
EXIT  
8. Press EXIT to return to normal viewing.  
To cancel the off timer:  
Select CLEAR in step 7 above.  
Press EXIT to return to normal viewing.  
23  
J3M60921A(E)_P17-26  
23  
18/01/2005, 3:43 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the picture quality  
You can adjust the picture quality to your personal preferences,  
including the contrast, brightness, color, tint, and sharpness. The  
qualities you choose will be stored automatically in your TVs memory  
so you can recall them at any time.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
To adjust the picture quality:  
1. Press MENU, then press or to display the PICTURE menu.  
+10  
100  
0
CH  
+
CH  
PICTURE AUDIO SETUP OPTION  
CONTRAST  
BRIGHTNESS  
COLOR  
64  
32  
32  
0
VOL  
VOL  
+
MENU/  
ENTER  
Menu  
TINT  
SHARPNESS  
SELECT  
32  
CH  
ADJUST  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
2. Press L or M until the item you want to adjust is highlighted.  
Exit  
3. Press or to adjust the level.  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
Reset  
Selection  
Pressing  
CODE  
MTS  
SLEEP  
MUTE  
contrast  
brightness  
color  
tint  
sharpness  
lower  
darker  
paler  
reddish  
softer  
higher  
lighter  
deeper  
greenish  
sharper  
Note:  
To reset the picture adjustments to the factory  
settings, press RESET.  
4. Press EXIT to return to normal viewing.  
To select the input mode:  
Watching video input  
You can use the TV/VIDEO button on the remote control to view a signal  
coming from other devices, such as VCRs or video disc players that may  
be connected to your TV. (See Connecting your TVon page 7.)  
Press the TV/VIDEO button repeatedly to  
select the desired mode. The signal source  
you are connected to is displayed in light blue.  
TV  
VIDEO 1  
VIDEO 2  
VIDEO 3  
Specifying the ColorStream® setting  
COLOR  
STREAM  
You can use the ColorStream (component video) input for connecting  
either a DVD player or a DTV receiver.  
Note: This TV is not HD ready.  
1. Press TV/VIDEO to put the TV in  
CH  
ColorStream mode.  
PICTURE AUDIO SETUP OPTION  
2. Press MENU, then press or until  
LANGUAGE  
ENGLISH  
POWER  
TV  
VCR  
CABLE  
DVD  
CH LABEL  
FAVORITE CH  
LOCK  
ON/OFF TIMER  
COLORSTREAM DVD DTV  
START  
START  
START  
OFF  
the OPTION menu appears.  
3. Press L or M to highlight  
COLORSTREAM.  
4. Press or to highlight DVD or  
DTV, depending on which device is  
connected.  
1
4
7
2
5
8
3
6
9
+10  
SELECT  
ADJUST  
100  
0
+
CH  
5. Press EXIT to return to normal viewing.  
Note: The factory setting is DVD.  
VOL  
VOL  
+
MENU/  
ENTER  
Displaying on-screen information  
Menu  
Press RECALL to display the following  
(
)
TV  
CH  
TV/Video  
Recall  
on-screen information:  
Clock  
Channel number or VIDEO mode  
selected  
12:00 AM  
STEREO  
SAP  
CABLE 007  
ABCD  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
Channel label (if preset)  
Stereo or SAP (second audio program)  
audio status  
CODE  
MTS  
SLEEP  
MUTE  
24  
J3M60921A(E)_P17-26  
24  
18/01/2005, 3:44 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the sleep timer  
You can set the TV so it turns off automatically.  
POWER  
TV  
VCR  
CABLE  
DVD  
To set the sleep timer:  
1
4
7
2
5
8
3
6
9
Repeatedly press SLEEP on the remote control to set the length of  
time until the TV turns off. The clock will count down 10 minutes for  
each press of the SLEEP button (120, 110, ...10, 0). After the sleep  
time is programmed, the display will appear briefly every ten minutes  
to remind you that the sleep timer is operating.  
+10  
100  
0
+
CH  
To confirm the sleep timer setting:  
Press SLEEP one time. The remaining time will be momentarily  
displayed.  
VOL  
VOL  
+
MENU/  
ENTER  
To cancel the sleep timer:  
CH  
Repeatedly press SLEEP until the display turns to 0.  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
FAV  
16:9  
VOL  
1/2  
16:9  
RESET CAP/TEXT  
1/2  
Using the closed caption feature  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CAP/TEXT  
The closed caption feature has two options: captions or text. A caption  
is a printed version of the dialogue, narration and/or sound effects of a  
program. Text is information not related to the program that appears on  
half of the TV screen when available.  
CODE  
MTS  
SLEEP  
MUTE  
Sleep  
To view captions or text:  
Note:  
1. Select the desired program. Closed captioned programs are  
usually marked in your local TV listing as CC.”  
2. Press CAP/TEXT repeatedly to select caption or text mode.  
A closed caption signal may not be decoded  
in the following situations:  
When a video tape has been dubbed.  
When the signal reception is weak.  
When the signal reception is non-standard.  
When you select the text mode, the text  
screen always appears as a black box. When  
there is no signal, however, the text screen  
will not display text characters. Repeatedly  
press CAP/TEXT until the box disappears.  
CAPTION CH1  
TEXT CH1  
3. Press 1/2 to select the caption or text channel.  
TEXT CH2  
CAPTION CH2  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
Avoid displaying stationary images on your  
TV screen for extended periods of time.  
Fixed (non-moving) images (such as  
black/gray bars in wide-screen picture  
formats, video game patterns, TV station  
logos, closed captions) can become  
permanently ingrained in the  
4. To turn off the closed caption feature, press CAP/TEXT  
repeatedly until captions or text no longer display on-screen.  
Changing the picture size  
You can change the picture size to 16:9 (widescreen) style.  
To view 16:9 style:  
Select the desired program, then press 16:9. The picture size will  
be displayed 16:9 style. 16:9will appear on the screen for approx.  
4 seconds.  
picture tube. This type of damage is  
NOT COVERED BY YOUR WARRANTY.  
To cancel 16:9 style:  
Press 16:9 again. The picture size will return to 4:3 style.  
16:9  
16:9 Widescreen  
4:3 Normal  
25  
J3M60921A(E)_P17-26  
25  
18/01/2005, 3:44 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the sound  
POWER  
TV  
VCR  
CABLE  
Muting the sound  
DVD  
Press MUTE to temporarily turn off the sound. While the sound is off,  
the screen will display the word MUTE in the lower right-hand corner.  
To restore the sound, press MUTE again.  
1
4
7
2
5
8
3
6
9
+10  
100  
0
Selecting stereo/SAP broadcasts  
+
CH  
You can listen to high-fidelity stereo sound with the Multi-channel TV  
Sound (MTS) feature. MTS can also transmit a second audio program  
(SAP) containing a second language or other audio information.  
VOL  
VOL  
+
MENU/  
ENTER  
CH  
When the TV receives a stereo or SAP broadcast, the word STEREO  
or SAP appears on-screen every time the TV is turned on, the channel  
is changed, or the RECALL button is pressed.  
EXIT  
RECALL TV/VIDEO  
FAV  
VOL  
CH RTN  
FAV  
Recall  
16:9  
RESET CAP/TEXT  
1/2  
The MTS feature is not available in the VIDEO mode.  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
You can leave your TV in STEREO mode because it will automatically  
output stereo or monaural sound, depending on the broadcast type. If  
the stereo sound is noisy, select MONO to reduce the noise. The word  
STEREO or SAP is displayed in light blue when the TV receives the  
signal.  
CODE  
MTS  
SLEEP  
MUTE  
Mute  
MTS  
To select the desired MTS setting:  
Repeatedly press the MTS button to select either STEREO, SAP,  
MONO+SAP, or MONO. If the current program is not available in  
stereo or SAP, the setting will not be available when you press the  
MTS button.  
STEREO  
MONO  
SAP  
MONO + SAP  
If the current program is not broadcasting either stereo or SAP, those  
settings will not be available when you press the MTS button.  
26  
J3M60921A(E)_P17-26  
26  
18/01/2005, 3:44 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the sound quality  
You can change the sound quality of your TV by adjusting the bass,  
treble, and balance.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
To adjust the sound quality:  
1. Press MENU, then press or until the AUDIO menu appears.  
+10  
100  
0
CH  
+
CH  
PICTURE AUDIO SETUP OPTION  
BASS  
32  
32  
0
VOL  
VOL  
+
MENU/  
ENTER  
TREBLE  
BALANCE  
BBE  
SURROUND  
STABLE SOUND OFF  
Menu  
Reset  
OFF  
OFF  
CH  
SELECT ADJUST  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
VOL  
FAV  
2. Press L or to highlight the item you want to adjust.  
3. Press or to adjust the level.  
16:9  
RESET CAP/TEXT  
1/2  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
CODE  
MTS  
SLEEP  
MUTE  
CH  
PICTURE AUDIO SETUP OPTION  
BASS  
32  
32  
0
TREBLE  
BALANCE  
BBE  
Note:  
OFF  
OFF  
To reset the audio adjustments to the factory  
settings, press RESET.  
SURROUND  
STABLE SOUND OFF  
SELECT ADJUST  
makes the sound quality weaker or decreases the balance in  
the right channel, depending on the item selected.  
makes the sound quality stronger or decreases the balance in  
the left channel, depending on the item selected.  
Using the BBE sound feature  
POWER  
TV  
VCR  
CABLE  
DVD  
By correcting the phase delay and distortion naturally generated by  
speaker systems, the BBE sound feature ensures that the sound that  
reaches your ears is as natural as the original sound. Human voices  
are clearer and music is natural and well-defined.  
1
4
7
2
5
8
3
6
9
+10  
100  
To turn on the BBE sound feature:  
1. Press MENU, then press or until the AUDIO menu appears.  
2. Press L or to highlight BBE.  
0
+
CH  
3. Press or to highlight ON.  
VOL  
VOL  
+
MENU/  
ENTER  
Menu  
CH  
PICTURE AUDIO SETUP OPTION  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
BASS  
32  
32  
0
TREBLE  
BALANCE  
BBE  
VOL  
FAV  
ON OFF  
OFF  
16:9  
RESET CAP/TEXT  
1/2  
SURROUND  
STABLE SOUND OFF  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
SELECT ADJUST  
CODE  
MTS  
SLEEP  
MUTE  
To turn off the BBE sound feature:  
Highlight OFF in step 3 above.  
Licensed by BBE Sound, Inc. under  
USP5510752 and 5736897.  
BBE and BBE symbol are registered trade-  
marks of BBE Sound, Inc.  
27  
J3M60921A(E)_P27-BACK  
27  
27/01/2005, 1:13 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the surround sound feature  
The surround sound feature expands the audio listening field wider and  
deeper to create exceptional sound quality from the TVs speakers.  
The feature uses stereo signals from a TV broadcast or video input.  
POWER  
TV  
VCR  
CABLE  
DVD  
1
4
7
2
5
8
3
6
9
+10  
To turn on the surround sound feature:  
1. Select the STEREO mode, if available (see Selecting stereo/SAP  
broadcastson page 26.)  
2. Press MENU, and then press or until the AUDIO menu  
appears.  
100  
0
+
CH  
VOL  
VOL  
+
3. Press L or M to highlight SURROUND.  
4. Press or to highlight ON.  
MENU/  
ENTER  
Menu  
CH  
EXIT  
RECALL TV/VIDEO  
CH RTN  
FAV  
CH  
PICTURE AUDIO SETUP OPTION  
VOL  
FAV  
BASS  
32  
32  
0
16:9  
RESET CAP/TEXT  
1/2  
TREBLE  
BALANCE  
BBE  
DISPLAY DVD CLEAR TOP MENU DVD MENU  
OFF  
ON  
CODE  
MTS  
SLEEP  
MUTE  
OFF  
SURROUND  
STABLE SOUND OFF  
SELECT ADJUST  
To turn off the surround sound feature:  
Highlight OFF in step 4 above.  
In general, you can leave your TV in surround mode because it will  
automatically output the type of sound being broadcast (surround  
stereo or monaural).  
Using the StableSound® feature  
The StableSoundfeature limits the highest volume level to prevent  
extreme changes in volume when the signal source is changed.  
To turn on the StableSound® feature:  
1. Press MENU, then press or until the AUDIO menu appears.  
2. Press L or M to highlight STABLE SOUND.  
3. Press or to highlight ON.  
CH  
PICTURE AUDIO SETUP OPTION  
BASS  
32  
32  
0
TREBLE  
BALANCE  
BBE  
OFF  
OFF  
SURROUND  
STABLE SOUND ON OFF  
SELECT ADJUST  
To turn off the StableSound® feature:  
Highlight OFF in step 3 above.  
Auto power off  
The TV will automatically turn off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its  
broadcast for the day and stops broadcasting on that channel. This feature does not work in VIDEO mode.  
Understanding the Power Return feature  
If the power is cut off while you are viewing the TV and the power is resupplied, the Power Return feature will turn the TV  
on automatically.  
If the power is going to be off for a long time or you are going to be away from home for a long time, unplug the power cord  
from the wall outlet to prevent the TV from turning on in your absence.  
28  
J3M60921A(E)_P27-BACK  
28  
18/01/2005, 3:45 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Troubleshooting  
Before calling a service technician, please check the following table for a possible cause of the problem and some solutions.  
Problem  
Solution  
TV will not turn on  
Make sure the power cord is plugged in, then press POWER.  
The remote control batteries may be dead. Replace the batteries.  
No picture, no sound  
Check the antenna/cable connections.  
This TV will not accept or display 480p or 720p progressive scan  
signals or 1080i interlaced high-definition signals through its  
ColorStream inputs. Switch the other devices output to 480i interlaced  
mode first (see page 9).  
No sound, picture OK  
The sound may be muted. Press VOLUME.  
The station may have broadcast difficulties. Try another channel.  
The MTS feature may be in SAP mode. Press the MTS button on the  
remote control until STEREO (or MONO) mode is active.  
Poor sound, picture OK  
Poor picture, sound OK  
The station may have broadcast difficulties. Try another channel.  
The MTS feature may be in SAP mode. Press the MTS button on the  
remote control until STEREO (or MONO) mode is active.  
Check the antenna connections.  
The station may have broadcast difficulties. Try another channel.  
Adjust the PICTURE menu.  
This TV will not accept or display 480p or 720p progressive scan  
signals or 1080i interlaced high-definition signals through its  
ColorStream inputs. Switch the other devices output to 480i interlaced  
mode first (see page 9).  
Poor reception of broadcast channels  
The station may have broadcast difficulties. Try another channel.  
Check the antenna connections.  
If you are using a VCR, make sure the TV/VCR button is set correctly.  
Cannot receive above channel 13  
Unable to select a certain channel  
Make sure the TV/CABLE feature in the SETUP menu is set to CABLE”  
The channel may be blocked by the CH LOCK feature, or erased with  
the add/erase feature.  
Cannot access signal input sources (Video1,  
Video2, Video3 and ColorStream) and/or  
Channels 3 and 4  
Check the VIDEO LOCK feature.  
Multiple images  
The station may have broadcast difficulties. Try another channel.  
Use a highly directional outdoor antenna.  
Poor color or no color  
The station may have broadcast difficulties. Try another channel.  
Adjust the TINT and/or COLOR in the PICTURE menu.  
If you change the direction of the TV while it is turned on, the picture  
could suffer from color shading. If so, turn off the TV and allow it to cool  
for several hours before turning it on again.  
Black box on screen  
Repeatedly press CAP/TEXT to turn off the Closed Caption Text mode.  
No stereo or SAP sound from a  
known MTS broadcast  
Make sure the MTS feature is set properly.  
The PIN code does not work  
Change or reset your PIN code (pages 18 and 19).  
The remote control does not operate  
Make sure the TV/VCR/DVD/CABLE mode is set properly on the  
remote control.  
Remove all obstructions between the remote control and the TV.  
The remote control batteries may be dead. Replace the batteries.  
29  
J3M60921A(E)_P27-BACK  
29  
18/01/2005, 3:45 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
This model complies with the specifications below.  
Design and specifications are subject to change without notice.  
This model may not be compatible with features and/or specifications that may be added in the future.  
Picture Tube  
600 mm (24 in.) diagonal (Screen size is approximate.)  
NTSC standard  
Television system  
Channel coverage  
VHF: 213  
UHF: 1469  
Cable TV: 4A, A-5A-1, A-I,  
+
+
JW, W 1W 84  
Power source  
120V AC, 60 Hz  
Power consumption  
Audio power  
125 W  
5 W + 5 W  
Speaker type  
51 mm x 119 mm (2 in. x 4-11/16 in.) x 2 pcs.  
Video/Audio terminals  
S-VIDEO INPUT  
Y-INPUT: 1V (p-p), 75 ohm, negative sync.  
C-INPUT: 0.286V (p-p) (burst signal), 75 ohm  
VIDEO/AUDIO INPUT  
VIDEO: 1V (p-p), 75 ohm, negative sync.  
AUDIO: 150 mV (rms) (30% modulation equivalent, 47k ohm)  
ColorStream® (component video) INPUT  
Y : 1V (p-p), 75 ohm  
PR : 0.7V (p-p), 75 ohm  
PB : 0.7V (p-p), 75 ohm  
VIDEO/AUDIO OUTPUT  
VIDEO: 1V (p-p), 75 ohm, negative sync.  
AUDIO: 150 mV (rms) (30% modulation equivalent, 47k ohm)  
Dimensions  
Width : 670 mm (26-3/8 in.)  
Height : 509 mm (20-1/16 in.)  
Depth : 471.5 mm (18-9/16 in.)  
Weight  
72.8 Ibs. (33 kg)  
Supplied accessories  
Remote control with two size AAAbatteries  
30  
J3M60921A(E)_P27-BACK  
30  
18/01/2005, 3:46 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Canada Warranty  
for 27'' and All Smaller Television Models  
Toshiba of Canada Limited (“TCL) makes the following limited  
Your Responsibility  
warranties to original consumers in Canada. THESE LIMITED  
WARRANTIES EXTEND TO THE ORIGINAL CONSUMER  
PURCHASER OR ANY PERSON RECEIVING THIS TELEVISION AS A  
GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO  
OTHER PURCHASER OR TRANSFEREE.  
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING  
CONDITIONS:  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this television must be performed by an  
Authorized TCL Service Depot.  
(3) These warranties from TCL are effective only if the television is  
purchased in Canada from an authorized TCL dealer and  
operated in Canada.  
(4) Labor charges for installation, setup, adjustment of customer  
controls, and installation or repair of antenna systems are not  
covered by these warranties. Reception problems caused by  
inadequate antenna systems are your responsibility.  
PRODUCTS PURCHASED IN CANADA AND USED ANYWHERE  
OUTSIDE OF CANADA, INCLUDING, WITHOUT LIMITATION, THE  
U.S.A. AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.  
PRODUCTS PURCHASED ANYWHERE OUTSIDE OF CANADA,  
INCLUDING, WITHOUT LIMITATION, THE U.S.A. AND MEXICO,  
AND USED IN CANADA, ARE NOT COVERED BY THESE WARRANTIES.  
(5) Warranties extend only to defects in materials or workmanship  
as limited above and do not extend to any television or parts that  
have been lost or discarded by you or to damage to television or  
parts caused by fires, misuse, accident, Acts of God (such as  
lightning or fluctuations in electric power), improper installation,  
improper maintenance, or use in violation of instructions  
Limited One (1) Year Warranty on Parts and Labor*  
TCL warrants this television and its parts against defects in materials  
or workmanship for a period of one (1) year after the date of original  
retail purchase. DURING THIS PERIOD, TCL WILL, AT TCLS  
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW  
OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS  
OR LABOR. YOU MUST DELIVER THE ENTIRE TELEVISION TO  
AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR ALL  
TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE SERVICE DEPOT.  
furnished by TCL; or to units that have been modified or had the  
serial number removed, altered, defaced, or rendered illegible.  
How to Obtain Warranty Services  
If, after following all of the operating instructions in this manual and  
checking the “Troubleshooting” section, you find that service is needed:  
(1) To find the nearest TCL Authorized Service Depot, visit TCLs web site  
Limited Two (2) Year Warranty on Picture Tube*  
TCL further warrants the picture tube in this television against defects  
in materials or workmanship for a period of two (2) years after the  
date of original retail purchase. DURING THIS PERIOD, TCL WILL,  
AT TCLS OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE  
TUBE WITH A NEW OR REFURBISHED PICTURE TUBE WITHOUT  
CHARGE TO YOU, EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE  
IS REPAIRED OR REPLACED AFTER ONE (1) YEAR FROM THE  
DATE OF THE ORIGINAL RETAIL PURCHASE, YOU MUST PAY  
ALL LABOR CHARGES INVOLVED IN THE REPAIR OR  
REPLACEMENT. YOU MUST DELIVER THE ENTIRE TELEVISION  
TO AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR  
ALL TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE SERVICE DEPOT.  
(2) Present your bill of sale or other proof of purchase to the Authorized  
Service Depot. You must deliver the entire television to an Authorized  
TCL Service Depot. You must pay for all transportation and insurance  
charges for the television to and from the Service Depot.  
For additional information,  
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF  
CANADA, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED  
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY  
WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF  
CANADA AS HEREBY LIMITED, THE FOREGOING WARRANTY IS  
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,  
GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF  
TCL WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY  
PARTS. IN NO EVENT SHALL TCL BE LIABLE FOR  
Rental Units  
The warranty for rental units begins with the first rental or thirty (30)  
days from the date of shipment to the rental firm, whichever comes first.  
CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT  
NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, OR  
MODIFICATION OR ERASURE OF RECORDED DATA CAUSED BY  
USE, MISUSE, OR INABILITY TO USE THIS PRODUCT).  
*Limited Warranty for Commercial Units  
TCL warrants televisions sold and used for commercial purposes as  
follows: all parts are warranted against defects in materials or  
workmanship for a period of ninety (90) days after the date of original  
purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S OPTION,  
REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR  
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS  
OR LABOR. YOU MUST DELIVER THE ENTIRE TELEVISION TO  
AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR  
ALL TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE SERVICE DEPOT.  
No person, agent, distributor, dealer, or company is authorized to  
change, modify, or extend the terms of these warranties in any manner  
whatsoever. The time within which action must be commenced to  
enforce any obligation of TCL arising under this warranty or under any  
law of Canada or of any province thereof is hereby limited to 90 days  
from the date you discover, or should have discovered, the defect. This  
limitation does not apply to implied warranties arising under the law of  
any province of Canada.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND  
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY  
FROM PROVINCE TO PROVINCE IN CANADA. SOME  
PROVINCES OF CANADA DO NOT ALLOW LIMITATIONS ON  
HOW LONG AN IMPLIED WARRANTY LASTS, WHEN AN  
ACTION MAY BE BROUGHT, OR THE EXCLUSION OR  
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT  
APPLY TO YOU UNDER SUCH CIRCUMSTANCES.  
Owner’s Manual and Product Registration  
Read this owner’s manual thoroughly before operating this television.  
Register your product online at www.toshiba.ca as soon as possible.  
By registering your product, you will enable TCL to bring you new  
products specifically designed to meet your needs and help us to  
contact you in the unlikely event a safety notification is required  
under the U.S. Consumer Product Safety Act. Failure to register your  
product does not diminish your warranty rights.  
[011005]  
31  
J3M60921A(E)_P27-BACK  
31  
19/01/2005, 9:04 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TEL.: (905) 470-5400  
Service Centers:  
TORONTO: 191 McNABB STREET,  
MARKHAM, ONTARIO, L3R 8H2, CANADA  
TEL.: (905) 470-5400  
MONTREAL: 18050 TRANS CANADA, KIRKLAND,  
QUEBEC, H9J-4A1, CANADA  
TEL.: (514) 390-7766  
VANCOUVER: 22171 FRASERWOOD WAY,  
RICHMOND, B.C., V62 1J5, CANADA  
TEL.: (604) 303-2500  
ColorStream®, FST Pure® and StableSound® are registered  
trademarks of Toshiba America Consumer Products, L.L.C.  
GameTimer is a trademark of Toshiba America Consumer Products, L.L.C.  
PRINTED IN THAILAND  
J3M60921A(E)_P27-BACK  
32  
18/01/2005, 3:47 AM  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tech Craft TV Video Accessories BCE32 User Manual
Tektronix Water Dispenser 494A User Manual
Toastmaster Waffle Iron TWB2PIZ User Manual
Topfield Satellite TV System TF 5000 CI User Manual
Toshiba CRT Television 13A24 User Manual
Toshiba Flat Panel Television P42LHA User Manual
Toshiba Printer B EV4T User Manual
Univex TV DVD Combo A9DN1UH User Manual
ViewSonic Flat Panel Television VG721M User Manual
Volvo Automobile 850 User Manual