RuggedSwitch®
RSG2288
9-Port Modular Managed Gigabit Ethernet Switch
Installation Guide
February 15, 2011
RuggedCom Inc. I 300 Applewood Crescent, Concord, Ontario, Canada L4K 5C7
Tel: +1 905 856 5288 I Fax: +1 905 856 1995 I Toll Free: 1 888 264 0006
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communications Commission Radio
Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference on his own expense.
CAUTION
This product contains a laser system and is classified as a “CLASS 1 LASER PRODUCT”
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
This product contains no user-serviceable parts. Attempted service by unauthorized personnel
shall render all warranties null and void.
Changes or modifications not expressly approved by RuggedCom Inc. could invalidate
specifications, test results, and agency approvals, and void the user’s authority to operate the
equipment.
Should this device require service, please refer to the “Warranty” section of this guide.
IMPORTANT
This product should be installed in a restricted access location where access can only be
gained by service personnel or users who have been instructed about the reasons for the
restrictions applied to the location and about any precautions that shall be taken; and access
is through the use of a tool or lock and key, or other means of security, and is controlled by
the authority responsible for the location.
3
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Table of Contents..............................................................................................................4
Table of Figures ................................................................................................................6
Table of Tables .................................................................................................................7
Product Overview......................................................................................................8
Functional Overview..........................................................................................8
Feature Highlights .............................................................................................8
Mounting Flexibility..........................................................................................11
Ethernet Panel Description..............................................................................12
Display Panel Description ...............................................................................15
Installation...............................................................................................................17
Rack Mounting ................................................................................................17
Panel and DIN Rail Mounting..........................................................................18
Dielectric Strength (HIPOT) Testing................................................................24
Console Port Wiring ........................................................................................26
Ethernet Ports .................................................................................................27
Transient Suppression.............................................................................28
IRIG-B Outputs........................................................................................34
Technical Specifications..........................................................................................36
Power Supply Specifications...........................................................................36
Failsafe Relay Specifications ..........................................................................36
Networking Standards Supported ...................................................................36
Copper Ethernet Port Specifications ...............................................................37
Fiber Ethernet Optic Specifications.................................................................37
PTP Card Specifications .................................................................................39
IRIG-B Outputs........................................................................................39
Operating Environment ...................................................................................39
Mechanical Specifications...............................................................................40
Type Tests ..............................................................................................................41
IEC 61850-3 Type Tests .................................................................................41
IEEE 1613 Type Tests ....................................................................................42
4
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Agency Approvals ...................................................................................................43
Warranty..................................................................................................................43
IEC Environmental Type Tests........................................................................42
5
RuggedSwitch® RSG2288 Installation Guide rev103
RuggedCom®
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Figures
Table of Figures
Figure 2: RSG2288 Ethernet Port Layout .......................................................................12
Figure 3: Ethernet panel LEDs........................................................................................12
Figure 5: 1000LX GBIC connector..................................................................................13
Figure 6: 1000LX LC connector ......................................................................................14
Figure 7: 1000LX SC connector......................................................................................14
Figure 8: 1000LX ST connector ......................................................................................14
Figure 9: 100FX MTRJ connector...................................................................................14
Figure 10: RSG2288 LED Display Panel ........................................................................15
Figure 11: RS2000 Family 19” Rack Mount Adapters.....................................................17
Figure 12: Rack mount adapter mounting location .........................................................17
Figure 14: RS2000 Series Philips Screw Terminal Block ...............................................19
Figure 15: RS2000 Series Phoenix Plug Terminal Block................................................19
Figure 16: Chassis Ground Connection..........................................................................20
Figure 17: AC Single Power Supply Wiring Example......................................................21
Figure 19: DC Power Supply Wiring Examples...............................................................22
Figure 20: DC and AC Power Supply Wiring Examples..................................................23
Figure 21: Dielectric Strength (HIPOT) Testing ..............................................................24
Figure 22: Failsafe Alarm Relay Wiring...........................................................................25
Figure 23: Console port on display board .......................................................................26
Figure 24 : RS2000 Series Console cable......................................................................26
Figure 25 : RJ45 port pin configuration...........................................................................27
Figure 26: SFP Orientation for top row and bottom row ports.........................................29
Figure 27: Locking latch location on GBIC optical modules............................................30
Figure 28: SFP Bail Latch location..................................................................................30
Figure 29: SFP Removal.................................................................................................30
Figure 30: PTP Card Panel Description..........................................................................32
Figure 31: IRIG-B Simplified Schematic..........................................................................35
Figure 32: RSG2288 Mechanical Dimensions ................................................................40
6
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Tables
Table of Tables
Table 1: Pluggable Fiber Transceiver Modules...............................................................13
Table 2: Fixed Fiber Transceivers...................................................................................14
Table 3: LED Display – Device status LED behavior definition.......................................15
Table 4: Port Status behavior definition ..........................................................................16
Table 6: RS232 over RJ45 console cable pin-out...........................................................26
Table 7: RJ45 Ethernet pin assignment..........................................................................27
Table 9: RSG2888 Time Synchronization Sources.........................................................31
Table 10: RSG2288 Time Synchronization Services......................................................31
Table 11: PTP Card Connectors.....................................................................................32
Table 12: PTP Card LED Functions................................................................................32
Table 13: GPS Antenna Specifications...........................................................................33
Table 14: Coaxial Cable Delay........................................................................................34
Table 15: IRIG-B PWM Output Specifications ................................................................39
Table 16: IRIG-B AM Output Specifications....................................................................39
Table 17 - IEC 61850-3 Type Tests................................................................................41
Table 18 - IEEE 1613 Type Tests...................................................................................42
Table 19 - Environmental Type Tests .............................................................................42
7
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1 Product Overview
1.1 Functional Overview
The RuggedSwitch® RSG2288 is an industrially hardened, fully managed,
modular, Ethernet switch specifically designed to operate reliably in electrically
harsh and climatically demanding utility substation and industrial environments.
The RSG2288 includes the IEEE 1588 v2 protocol with hardware time stamping
allowing high precision time synchronization over the Ethernet network with
accuracies of 1us or better. The RSG2288’s superior ruggedized hardware
design coupled with the embedded Rugged Operating System (ROSTM) provides
improved system reliability and advanced cyber security and networking features,
making it ideal for creating mission-critical, Gigabit networks or aggregating
switches into a Gigabit backbone.
The RSG2288’s modular flexibility offers 100/1000BaseX fiber and
10/100/1000BaseTX copper port combinations. Support for front or rear mount
connectors coupled with support for multiple fiber connector types (SFP, GBIC,
LC, SC) without loss of port density makes the RSG2288 highly versatile and
suitable for any application. The RSG2288 is packaged in a rugged, galvanized
steel enclosure with industrial grade DIN, panel, or 19” rack-mount mounting
options.
1.2 Feature Highlights
Ethernet Ports
Up to 9-Gigabit Ethernet ports supporting copper and fiber media
Up to 9 100FX Fiber Fast Ethernet ports
2 port modules for tremendous flexibility
Fiber types supported include multimode, singlemode, and bidirectional
single strand
Full compliance with IEEE: 802.3, 802.3u & 802.3z
Non-blocking, store and forward switching
Full duplex operation and flow control (IEEE 802.3x)
Industry standard fiber optical connectors: LC, SC, SFP, GBIC
Long haul optics allow Gigabit distances up to 70km
Advanced Time Synchronization
Support for IEEE 1588 v2, GPS, and IRIG-B time synchronization
Hardware time stamping on all ports including Gigabit
Transparent clock operation for high precision on switched networks (1us or
better)
Peer-to-peer path delay measurements
High precision TCXO (Temperature Compensated Oscillator)
Supports master, slave and transparent clock modes
Support for IRIG-B input and output
8
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
Cyber Security Features
Multi-level user passwords
SSH/SSL encryption
MAC-based port security
Selective port enable/disable
Port-based network access control using IEEE 802.1x
VLAN support (IEEE 802.1Q) to segregate and secure network traffic
RADIUS centralized access management
SNMPv3 featuring encrypted authentication and session
RuggedRated™ for Reliability in Harsh Environments
Immunity to EMI and heavy electrical surges
o Zero-Packet-Loss™ Technology
o Meets IEEE 1613 Class 2 (electric utility substations)
o Exceeds IEC 61850-3 (electric utility substations)
o Exceeds IEEE 61800-3 (variable speed drive systems)
o Exceeds IEC 61000-6-2 (generic industrial environment)
o Exceeds NEMA TS-2 (traffic control equipment)
-40 to +85°C operating temperature (no fans)
Conformal coated printed circuit boards (optional)
18 AWG galvanized steel enclosure
Hazardous Location Certification: Class 1 Division 2
Universal Power Supply Options
Fully integrated, dual-redundant (optional) power supplies
Universal high-voltage range: 88-300VDC or 85-264VAC
Popular low voltage DC ranges: 12, 24 or 48 VDC
Screw or pluggable terminal blocks for reliable, maintenance-free
connections
CSA/UL 60950 safety approved to +85°C
Rugged Operating System (ROS™) Networking Features
Simple plug and play operation: automatic learning, negotiation, and
crossover detection
RSTP (Rapid Spanning Tree Protocol) support: IEEE 802.1w
eRSTP™ (Enhanced Rapid Spanning Tree) support, <5ms network fault
recovery
QoS (Quality of Service) support: IEEE 802.1p, for real-time traffic
VLAN (Virtual LAN) support: IEEE 802.1Q with double tagging
GVRP (GARP VLAN Registration Protocol) support: IEEE 802.1D
GMRP (GARP Multicast Registration Protocol) support: IEEE 802.1D
Link Aggregation support: IEEE 802.3ad
IGMP Snooping for multicast filtering
Port rate limiting and broadcast storm limiting
9
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
Port configuration, status, statistics, mirroring, security
Loss of link management on fiber ports
SNTP time synchronization (both client and server)
Industrial automation features (e.g. Modbus)
Rugged Operating System (ROS™) Management Features
Secure Web-based management interface
Console menu and Command Line management interfaces via SSH, RSH,
and Telnet
SNMP v1, v2c, and v3
RMON (Remote MONitoring)
Rich set of diagnostics with logging and alarms
10
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1.3 Mounting Flexibility
The RS2000 series of products have been designed with maximum mounting
and display flexibility. Customers can order an RS2000 series switch that can be
mounted in a standard 19” rack, 1” DIN Rail, or directly onto a panel. For rack
mount installations, the RS2000 series can be ordered with connectors on the
front panel or on the rear of the chassis. Placing the connectors on the rear
allows all data and power cabling to be installed and connected at the rear of the
Figure 1: RSG2288 Rack mount chassis orientation options – Front and rear mount.
11
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1.4 Ethernet Panel Description
The Ethernet connector panel of the RSG2288 is organized into six slots, five of
which are modular and may be selected at the time the unit is ordered. Figure 2
shows the physical layout of these ports.
Figure 2: RSG2288 Ethernet Port Layout
Slots 1, 2, 3 and 4 support two-port Ethernet modules up to 1Gbps. Slot 5
supports a one-port module up to 1Gbps. Slot 6 contains the PTP Source Card
for the RSG2200 series. The complement of modules installed on a particular
unit may be determined by reading the factory data file via the RuggedSwitch®
ROSTM user interface.
Each Ethernet port is equipped with an LED per port that indicates link/activity
status information. The LED is solid for ports with a valid link, and blinks for
2 along with the associated link/activity LEDs for each port.
Figure 3: Ethernet panel LEDs
12
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1.4.1 Fiber Optic Transceiver Orientation and Connection
Depending on the order code of the product, the RSG2200 series products can
be equipped with several different types of fiber optic ports. The Transmit (TX)
and Receive (RX) connections of each port must be properly connected and
matched for proper link and operation. Modules populated on the top row of the
device typically have locking mechanisms or tabs facing the top of the unit.
Modules located on the bottom row of the device have locking mechanisms or
tabs facing the bottom of the unit.
The diagrams in this section depict each fiber connector style supported by the
RuggedSwitch® in order to provide a reference for the proper orientation of cable
connections. A front view (looking into the connector) and a top view of the
connector module are shown for each one. Note that if modules are populated on
the bottom row of the device, the transceiver orientation will be inverted relative
to the diagram (i.e. RX and TX will be reversed).
Figure 4 and Figure 5 show front and top views of the pluggable fiber transceiver
modules supported by RuggedSwitch®. Note that when the module is installed in
the unit, most of the body of the module as shown in top views below will not be
visible.
Table 1: Pluggable Fiber Transceiver Modules
Figure 5: 1000LX GBIC connector
Figure 4: 1000LX SFP (mini-GBIC) Module and
LC connector
13
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
Figure 6 through Figure 9 show front and top views of the fixed fiber transceiver
modules supported by RuggedSwitch®. Note that when the daughter card
containing transceiver modules is installed in the unit, most of the body of the
module as shown in top views below will not be visible.
Table 2: Fixed Fiber Transceivers
Figure 7: 1000LX SC connector
Figure 6: 1000LX LC connector
Figure 9: 100FX MTRJ connector
Figure 8: 1000LX ST connector
14
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
1.5 Display Panel Description
RuggedCom RS2000 series products are equipped with a versatile display panel,
shown in Figure 10, which is designed to provide quick status information for
each port, as well as the entire device to allow for simple diagnostics and
troubleshooting. It features:
RS232 console port for ‘out of band’ console access and configuration
Power supply and Alarm status indicators
Convenient port status indicators conveying Link/Activity, Duplex, or Speed
via the Mode push-button (toggles between the three display modes)
System reset via the Mode push-button (if held for 5 seconds)
Figure 10: RSG2288 LED Display Panel
The device status LEDs provide a quick visual indication of the operational status
of the unit. Table 3 lists the possible LED colors and the corresponding
description.
LED
Color
Green
Description
Power supply operating normal
Power supply failure
Red
Off
PS1 / PS2
No power supply installed
Red
An alarm condition exists – log in to the web
management interface or to the CLI to determine
the alarm code
Alarm
Off
No alarms exist
Table 3: LED Display – Device status LED behavior definition
15
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
The port-based LEDs can be cycled between three display modes: Status,
Duplex, and Speed. Pushing the mode button causes the display mode to be
cycled.
Mode
Color
Green (Solid)
Description
Link detected
Green (Blinking)
Off
Activity
Status
No link
Green (Solid)
Orange (Solid)
Off
Full-Duplex operation
Half-Duplex operation
No link
Duplex
Speed
Green (Blinking)
Green (Solid)
Orange (Solid)
Off
1000Mb/s
100Mb/s
10Mb/s
No link
Table 4: Port Status behavior definition
16
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2 Installation
2.1 Rack Mounting
The RS2000 family of products can be rack mounted using the included rack
mount adapter assemblies shown in Figure 11. Secure the rack mount adapter to
the front side of the chassis using the included black PAN head Philips screws in
the positions shown in Figure 13. The entire chassis can then be mounted to a
standard 19” rack. An additional two rack mount adapters are included to
optionally secure the rear of the chassis in high-vibration or seismically active
locations.
Figure 11: RS2000 Family 19” Rack Mount Adapters
Figure 12: Rack mount adapter mounting location
Note:
Since heat within the RSG2288 is channeled to the enclosure, it is recommended
that 1 rack-unit of space (1.75”) be kept unpopulated and free of equipment
above each RS2000 series product to allow for a small amount of convectional
airflow. Although forced airflow is not necessary, any increase in airflow will result
in a reduction of ambient temperature that will improve long-term reliability of all
equipment mounted within the rack space.
17
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.2 Panel and DIN Rail Mounting
RS2000 series products can be ordered as a Panel/DIN mount chassis. Both
options involve the use of the panel/DIN adapters to be mounted on each side of
the chassis enclosure. The adapter allows for the chassis to be mounted on the
standard 1” DIN rail using the grooves in the adapter, secured using the included
Philips screw. See Figure 13 for a PANEL/DIN mount diagram.
Figure 13: RSG2200 PANEL/DIN RAIL mounting diagram
18
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.3 Power Supply Wiring and Grounding
RS2000 series products support dual redundant power supplies – “Power Supply
1 (PS1)” and “Power Supply 2 (PS2)”. The connections for PS1, PS2 and the fail-
RSG2200 series products can be equipped with either a Philips Screw Terminal
Block or a Phoenix Plug Terminal Block. The Philips Screw Terminal Block has
Philips screws with a compression plate allowing either bare wire connections or
crimped, terminal lugs. We recommend the use of #6 size ring lugs to ensure
secure, reliable connections under severe shock or vibration. Both terminal
blocks have a safety cover which must be removed via two Phillips screws before
connecting any wires. The safety cover must be re-attached after wiring to
ensure personnel safety. Refer to Table 5 below for a description of each
terminal as well as sections 2.3.1 through 2.3.3 for wiring examples.
Figure 14: RS2000 Series Philips Screw Terminal Block
Philips Screw Terminal with Cover
Philips Screw Terminal without Cover
Safety Cover
Terminal
Chassis Ground
Connection
Surge / Chassis
Ground Jumper
Safety Cover
Screws
Phoenix Plug Terminal with Cover
Phoenix Plug Terminal without Cover
Safety Cover
Screws
Surge / Chassis
Ground Jumper
Safety Cover
Terminal
Chassis Ground
Connection
Figure 15: RS2000 Series Phoenix Plug Terminal Block
19
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The RS2000 Family chassis ground connection, shown in Figure 16, uses a #6-
32 screw. It is recommended to terminate the ground connection in a #6 ring lug,
and to use a torque setting not exceeding 15 in.lbs (1.7 Nm).
#6-32 screw
with ext.
washer.
#6 ring lug
stainless steel standoff
Figure 16: Chassis Ground Connection
Terminal
Number
Description
PS1 Live / +
Usage
PS1 Live / + is connected to the positive (+) terminal if the
power source is DC or to the (Live) terminal if the power
source is AC.
1
PS1 Surge Ground is connected to the Chassis Ground
via a jumper on the terminal block. Surge Ground is used
as the ground conductor for all surge and transient
suppression circuitry. NOTE: Surge Ground must be
disconnected from Chassis Ground during HIPOT
(dielectric strength) testing.
2
PS1 Surge Ground
PS1 Neutral / - is connected to the negative (-) terminal if
the power source is DC or to the (Neutral) terminal if the
power source is AC.
Chassis Ground is connected to the Safety Ground
terminal for AC inputs or the equipment ground bus for DC
inputs. Chassis ground connects to both power supply
surge grounds via a removable jumper.
PS2 Live / + is connected to the positive (+) terminal if the
power source is DC or to the (Live) terminal if the power
source is AC.
3
4
5
PS1 Neutral / -
Chassis Ground
PS2 Live / +
PS2 Surge Ground is connected to the Chassis Ground
via a jumper on the terminal block. Surge Ground is used
as the ground conductor for all surge and transient
suppression circuitry. NOTE: Surge Ground must be
disconnected from Chassis Ground during HIPOT
(dielectric strength) testing.
PS2 Neutral / - is connected to the negative (-) terminal if
the power source is DC or to the (Neutral) terminal if the
power source is AC.
6
7
PS2 Surge Ground
PS2 Neutral / -
8
9
Relay NO Contact
Relay Common
Normally open, failsafe relay contact.
Failsafe relay common contact.
10
Relay NC Contact
Normally closed, failsafe relay contact.
Table 5: RS2000 Series Power terminal block connection description
20
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.3.1 AC Power Supply Wiring Examples (RSG2288)
Figure 17: AC Single Power Supply Wiring Figure 18: AC Dual Redundant Power Supply
Example
Wiring Example
Notes:
100-240VAC rated equipment: A 250VAC appropriately rated circuit breaker
must be installed.
Equipment must be installed according to the applicable country wiring
codes.
When equipped with two HI voltage power supplies, independent AC sources
can be used to power the product for greater redundancy.
21
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.3.2 DC Power Supply Wiring Examples
Figure 19: DC Power Supply Wiring Examples
Notes:
125/250VDC rated equipment: A 300VDC appropriately rated circuit breaker
must be installed.
A circuit breaker is not required for 12, 24 or 48 VDC rated power supplies.
For dual DC power supplies, Separate circuit breakers must be installed and
separately identified.
Equipment must be installed according to the applicable country wiring
codes.
22
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.3.3 Dual Power Supplies – DC and AC Inputs
Figure 20: DC and AC Power Supply Wiring Examples
Notes:
125/250VDC rated equipment: A 300VDC appropriately rated circuit breaker
must be installed.
100-240VAC rated equipment: A 250VAC appropriately rated circuit breaker
must be installed.
A circuit breaker is not required for 12, 24 or 48 VDC rated power supplies.
Separate circuit breakers must be installed and separately identified.
Equipment must be installed according to the applicable country wiring
codes.
23
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.4 Dielectric Strength (HIPOT) Testing
For dielectric strength (HIPOT) testing in the field, users must remove the metal
jumper located on terminal 2, 4, and 6 of the power supply terminal block. This
metal jumper connects transient suppression circuitry to chassis ground and
must be removed in order to avoid damage to transient suppression circuitry
during HIPOT testing. Figure 21 shows the proper HIPOT test connections and
should be followed to avoid damage to the device.
Figure 21: Dielectric Strength (HIPOT) Testing
24
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.5 Failsafe Alarm Relay Wiring and Specifications
The “Failsafe” output relay is provided to signal critical error conditions that may
occur on RS2000 series products. The contacts are energized upon power-up of
the unit and remain energized unless a critical error occurs. The proper relay
connections are shown in Figure 22. Control of the output is user-selectable and
can be programmed via the Rugged Operating System (ROS®). One common
application for this output is to signal an alarm if a power failure or removal of
control power occurs.
Figure 22: Failsafe Alarm Relay Wiring
25
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.6 Console Port Wiring
A RS232 console port for configuration and management of the device is located
on the LED display module shown in Figure 23. This port is intended to be a
temporary connection during initial configuration or troubleshooting and allows for
direct serial access to the management console. The connection is made using
the DB9-Female to RJ45 console cable included in the device packaging shown
in Figure 24. Console connection settings are: 57600 baud, no parity bits, 8 data
bits, and 1 stop bit.
Figure 23: Console port on display board
Figure 24 : RS2000 Series Console
cable
For user reference, the console cable pin-out is show in Table 6.
RuggedCom RS232 over RJ45 pin-out specification
Signal Name (PC is DTE)
DCD – Carrier detect
RxD – Receive data (to DTE)
TxD – Transmit data (from DTE)
DTR – Data terminal ready
GND – Signal GND
DSR – Data set ready
RTS – Ready to send
CTS – Clear to send
DB9- Female
RJ45 Male
1
2
3
4
5
6
7
8
9
2
5
6
3
4
1*
8
7
RI – Ring Indicator
1*
Table 6: RS232 over RJ45 console cable pin-out
After initial configuration, the RSG2288 can be configured via a number of new
mechanisms such as Telnet SSH, and the built-in web server. Consult the
ROS™ User Guide for further details.
Note:
This port is not intended to be a permanent connection.
Serial cable must not exceed 2m (6.5 ft) in length.
26
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.7 Ethernet Ports
2.7.1 RJ45 Twisted-Pair Data Ports
RSG2288 Ethernet switches are equipped with up to nine 10/100/1000BaseTX
ports that allow connection to standard CAT-5 UTP cable with RJ45 male
connectors. All RS2000 series RJ45 RuggedSwitch products feature auto-
negotiation, auto-polarity, and auto-crossover functions. The RJ45 receptacles
can also accept and take advantage of screened (commonly known as
“shielded”) cabling. Figure 25 shows the RJ45 port pins configuration.
Pin 8
Pin 1
Figure 25 : RJ45 port pin configuration.
10/100BaseTx Pin-out
Pin
Description
RX +
1
2
3
RX -
TX +
6
TX -
NC
4, 5, 7, 9
Table 7: RJ45 Ethernet pin assignment
2.7.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations
The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet
communications over distances of up to 100 meters using 4 pairs of category 5
(or higher) balanced, unshielded twisted-pair cabling. For wiring guidelines,
system designers and integrators should refer to the Telecommunications
Industry Association (TIA) TIA/EIA-568-A wiring standard that characterizes
minimum cabling performance specifications required for proper Gigabit Ethernet
operation. To ensure reliable, error-free data communications, new and pre-
existing communication paths should be verified for TIA/EIA-568-A compliance.
Table 8 summarizes the relevant cabling standards.
27
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Cabling
Category
1000BaseTx
Compliant
No
Required action
New wire infrastructure required
< 5
5
Yes
Verify TIA/EIA-568-A compliance
No action required. New installations should be designed
with Category 5e components or higher
No action required
5e
Yes
6
> 6
Yes
Yes
Connector and cabling standards to be determined.
Table 8: Cabling categories and 1000BaseTx compliance defined.
Follow these recommendations for copper data cabling in high electrical noise
environments:
Data cable lengths should be as short as possible - ideally limited to 3m (10ft)
in length. Copper data cables should not be used for inter-building
communications.
Power and data cables should not be run in parallel for long distances, and
ideally should be installed in separate conduits. Power and data cables
should intersect at 90 angles when necessary to reduce inductive coupling.
Shielded/screened cabling can optionally be used. The cable shield should
be grounded at one single point to avoid the generation of ground loops.
2.7.3 Transient Suppression
RuggedCom does not recommend the use of copper cabling of any length for
critical, real-time, substation automation applications. However, transient
suppression circuitry is present on all copper ports to protect against damage
from electrical transients and to ensure IEC 61850-3 and IEEE 1613 Class 1
conformance. This means that during the transient event, communications errors
or interruptions may occur but recovery is automatic. RuggedCom also does not
recommend using these ports to interface to field devices across distances which
could produce high levels of ground potential rise, (i.e. greater than 2500V)
during line-to-ground fault conditions.
2.8 Pluggable optics – Installation, removal, and
precautions
The RSG2200 series of products can be ordered with pluggable optic form
factors: SFP (Small Form-factor Pluggable) or GBIC (Gigabit Interface
Converter). SFP and GBIC modules can be safely inserted and removed while
the chassis is powered and operating – this feature is also known as “hot-
swappable”. When inserting or removing optics, there are several precautions
that should be taken. They include:
Ensuring that dust caps are mounted on SFP cages at all times unless a user
is in the process of inserting or removing an SFP module. The dust caps will
28
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
prevent the accumulation of residue or particles that may inhibit proper
operation.
Ensuring that the user has properly discharged any possible electrostatic
build-up in order to prevent electrostatic discharges (ESD). This can be
accomplished by proper user ‘grounding’ via an ESD wrist strap, or by
touching earth or chassis ground before performing installation or removal of
optics. ESD can damage or shorten the life of optical modules when not
plugged into a chassis.
Ensuring that SFP and GBIC optical modules are always stored in an ESD-
safe bag or other suitable ESD-safe environment, free from moisture and
stored at the proper temperature (–40 to +85C).
Disconnecting all cables from the SFP or GBIC module prior to insertion or
removal of the module.
Using only optics certified by RuggedCom Inc. with RuggedCom products.
Damage can occur to optics and product if compatibility and reliability have
not been properly assessed.
2.8.1 Module Insertion – GBICs and SFPs
Special attention must be paid to the orientation of SFP and GBIC modules upon
installation in the RuggedSwitch® chassis. For example, Figure 26 shows the
proper orientation of SFP modules installed to both upper and lower slots.
Modules on the upper row must be inserted top-side up, and modules on the
lower row must be inserted top-side down. SFP modules should be inserted with
the bail-latch in the locked position.
Figure 26: SFP Orientation for top row and bottom row ports
Both SFP and GBIC modules should gently slide into their ports and should lock
in place when fully inserted. Dust covers should be in place when installing the
modules, and should always be in place when cables are not connected.
Diagrams of both SFP and GBIC modules are provided in Table 1 as a guide to
the orientation of each type.
29
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.8.2 GBIC Module Removal
GBIC Modules have two locking latches, one on either side of the module, as
shown in Figure 27. To remove a GBIC module, disconnect any cables and
replace the dust cover to protect the optics. Depress both latches simultaneously
and gently pull the module from the chassis. The module should be immediately
stored in an ESD-safe environment.
Figure 27: Locking latch location on GBIC optical modules
2.8.3 SFP Module Removal
SFP Modules are removed using the metal bail latch located on the top of the
module as shown in Figure 28. To remove the SFP module, disconnect any
cables and replace the dust cover to protect the optics. Grasp the bail latch and
gently pull outwards to unlock and remove the module. Removal of an SFP
module is shown further in Figure 29. The module should be immediately stored
in an ESD-safe environment.
Figure 28: SFP Bail Latch location
Figure 29: SFP Removal
30
RuggedSwitch® RSG2288 Installation Guide rev103
RuggedCom®
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.9 Precision Time Protocol (PTP) Card and IEEE1588 v2
The Precision Time Protocol (PTP) card option for the RSG2288 adds the ability
to provide time synchronization via IRIG-B, and to synchronize to an external
IRIG-B source or to the GPS network. The time synchronization capabilities of
the RSG2288, both with and without the PTP card option, are summarized
below:
Without PTP
Card
With PTP
Card
Synchronization Source
NTP
IEEE 1588 v2
IRIG-B PWM
GPS
Table 9: RSG2888 Time Synchronization Sources
Without PTP
Synchronization Service
Card
With PTP
Card
NTP
IEEE 1588 v2
IRIG-B AM
IRIG-B PWM
Table 10: RSG2288 Time Synchronization Services
NTP (Network Time Protocol) is the standard for synchronizing the clocks of
computer systems throughout the Internet and is suitable for systems that require
accuracies in the order of 1 ms.
IRIG-B (Inter Range Instrumentation Group, mod B) time synchronization is an
even older, established, inter-device time synchronization mechanism providing
accuracy on the order of 1ms to 1µs.
The Global Positioning System (GPS), as a source of accurate time, requires an
external GPS antenna input to provide accurate time signals on the order of
500ns. The RSG2288 can use the GPS receiver on the PTP card to provide the
time base for the system.
IEEE 1588 is designed to fill a niche not well served by either of the two older,
dominant protocols, NTP and IRIG-B. IEEE 1588 is designed for local systems
requiring accuracies on the order of 100 nanoseconds. IEEE 1588 is also
designed for applications that cannot bear the cost of a GPS receiver at each
node or for which GPS signals are inaccessible. Every Ethernet port on the
RSG2288 supports IEEE1588.
The PTP card option is an ideal product for use in existing installations already
well served by NTP, IRIG-B or GPS. It also provides a migration path for the use
of the new IEEE 1588 v2 standard. As more end devices enter the market with
IEEE 1588 compatibility this card provides an easy transition to this new time
synchronization standard.
31
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2.9.1 PTP Card Panel Description
Figure 30: PTP Card Panel Description
The four BNC connectors on front panel of the PTP card are defined in Table 11,
below:
Connector
Function
IRIG-B123 AM signal output, software
enabled
AM OUT
IRIG-B003 PWM or 1 PPS signal output,
software selectable
TTL OUT
TTL IN
TTL-level IRIG-B PWM signal input
GPS antenna connector – please refer to
section 2.9.2 for detail.
GPS IN
Table 11: PTP Card Connectors
Note that only one input is active at a time. The IRIG-B PWM input or the GPS
input is selected in software. The color of the LED on the front panel of the PTP
card indicates the status of the incoming timing signal, depending on the input
selected:
Color
GPS Input
IRIG-B PWM Input
Valid signal
Green
Red
Lock
Holdover mode (GPS lock has Problems with IRIG-B signal
been achieved but the receiver
no longer sees the minimum
number of required satellites.)
Off
No signal detected
No signal detected
Table 12: PTP Card LED Functions
2.9.2 GPS Antenna Installation
The signals received from the GPS satellite network are at a frequency of
1575.42 MHz with a minimum power of -162 dBW. The GPS antenna must have
a clear view of the sky in order to receive the low power signals and track the
maximum number of satellites. Rooftops or other structures clear of obstructions
and with a clear view of the horizon are ideal.
Elements of a typical GPS antenna system:
Active GPS Antenna (required)
Coaxial cable to connect the elements (required)
32
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lightning arrestor (optional)
Line Amplifier or Filter (optional)
To ensure correct GPS signal reception, the overall system of antenna, cabling,
lightning arrestor, line amplifier and filters requires a relative gain which should
be greater than 5 dBi but less than 18 dBi (to avoid signal saturation at the
receiver input).
2.9.2.1 GPS Antenna
There are two major types of GPS antenna: passive and active. A passive
antenna requires no power and is an option when signal strength is not a
concern. An active antenna has a built in Low Noise Amplifier (LNA) to increase
the strength of the signal, and to compensate for the signal loss in a long cable
connection. Active antennas are used when the antenna input is connected to
the receiver through a coaxial cable (usually longer than 3 m) or any high loss
transmission path.
The PTP Card requires an active antenna with the following specifications:
Characteristic
Polarization
Active Antenna
Right-Hand Circular Polarized
1.57542 GHz ± 1.023 MHz
5 VDC
Receive Frequency
Power Supply
DC Current
< 10 mA at 3 VDC
Select antenna gain based on system
configuration
Antenna Gain
Total Gain at PTP GPS Input (includes
antenna gain, cable loss, lightning
arrestor loss, line amplifier gain and filter
loss)
Total Gain ≤ 18 dBi
Axial Ratio
< 3 dB
< 2.5
Output VSWR
Table 13: GPS Antenna Specifications
Notes:
The PTP card’s GPS input provides 5 VDC at up to 10 mA to power the
antenna.
Best results can be achieved with a total gain of 16 dB (includes antenna
gain, cable loss, lightning arrestor loss, line amplifier gain and filter loss) at
the antenna input.
2.9.2.2 Antenna Cabling
Cable Impedance:
RuggedCom recommends low loss 50 Ω coaxial cabling.
Cable Delay
Using any length of coaxial cable will add some time delay to the GPS signal
33
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
which degrades the accuracy of the calculated time and position. The time delay
is dependent on the type of dielectric material in the cable and ranges from 1 to 2
ns/ft. RuggedCom provides a method to account for this delay through the web
management interface by entering the time delay into the cable compensation
box under PTP General Configuration The table below gives some examples of
the delay that can be expected based on the dielectric type.
Propagation
Time Delay
Dielectric Type
Velocity
(% of c)
(ns/ft)
Solid Polyethylene (PE)
Foam Polyethylene (FE)
Foam Polystyrene (FS)
Air Space Polyethylene (ASP)
Solid Teflon (ST)
1.54
1.27
65.9
80.0
1.12
91.0
1.15-1.21
1.46
84-88
69.4
Air Space Teflon (AST)
1.13-1.20
85-90
Table 14: Coaxial Cable Delay
2.9.2.3 Lightning Considerations
Although it is not possible to protect the antenna from a direct lighting strike, the
antenna and connected components can be protected from secondary effects
through installation location and protection devices.
Install the antenna at least 15 meters away from and lower than any structures
that attract lightning. GPS antenna damage is usually not the result of a direct
lightning strike, but due to high currents induced by the effects of a lightning
strike on a nearby structure. RuggedCom also recommends installing lightning
arrestors in the antenna line to protect the receiver and connected devices. If a
lightning arrestor is installed, it is important to ensure that it has a low impedance
path to the ground.
2.9.2.4 Line Amplification and Filtering
Although an active antenna has gain, depending on the length of the coaxial
cable used it may not be enough in which case a line amplifier will be required as
well.
Most active antennas include filters; however, if there is a high potential for
electromagnetic interference, such as from the near field of a radio transmitter,
though the antenna system, additional antenna line filtering may be necessary.
2.9.3 IRIG-B Outputs
The PTP card provides IRIG-B outputs in both AM (Amplitude Modulated) and
PWM (Pulse Width Modulated) formats. The IRIG-B123 signal format is
supported on the AM OUT port, and the IRIG-B003 signal format is supported on
the TTL OUT port. Enabling and disabling the outputs, and selecting between
PWM and PPS on the TTL OUT port, is done through software.
34
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The number of IRIG-B devices that can be connected to the AM or PWM sources
is dependent on the cabling type and length as well as the input impedances of
the devices. Figure 31 shows a simplified circuit diagram of the interface between
an IRIG-B source and connected devices.
Source
Cabling
Rc
Device
Rs
Vs
RL/N
Figure 31: IRIG-B Simplified Schematic
The maximum number of devices (N) that can be connected to the source is
determined by checking if the source current (IS) required to drive the connected
devices is less than the maximum drive current the source can provide, and
verifying that the load voltage (VL) the connected devices see is greater than the
minimum required voltage. Please refer to section 3.6.1 for specifications of the
IRIG-B output port.
35
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
3 Technical Specifications
3.1 Power Supply Specifications
Input Range
Internal
Fuse
Max. Power
Power Supply Type
Consumption3
Min
Max
Rating
12 – 24 VDC
48 VDC
HI (125/250 VDC) 1
HI (110/230 VAC) 1
10 VDC
36 VDC
36 VDC
59 VDC
6.3A(F) 2
3.15A(T) 2
28W
88 VDC
85 VAC
300 VDC
264 VAC
2A(T) 1,2
Notes:
1. The “HI” power supply is the same power supply for both AC and DC.
2. (F) Denotes fast-acting fuse, (T) denotes time-delay fuse.
3. Power consumption varies based on configuration. 10/100Base-TX ports
consume roughly 1W less than fiber optic ports.
3.2 Failsafe Relay Specifications
Parameter
Value (Resistive Load)
250VAC, 125VDC
Max Switching Voltage
Rated Switching Current
2A @ 250VAC
0.15A @ 125VDC, 2A @ 30VDC
Max Switching Capacity
150W, 500VA
3.3 Networking Standards Supported
Standard
Description
IEEE 802.3
10BaseT
100BaseTX / 100BaseFX
1000BaseSX/LX
IEEE 802.3u
IEEE 802.3z
IEEE 802.3ab
IEEE 802.3x
IEEE 802.1D
IEEE 802.1Q
IEEE 802.1p
IEEE 1588 v2
1000BaseTx
Full Duplex Operation, Flow Control
MAC Bridges
VLAN (Virtual LAN) Tagging
Class of Service
Precision Time Protocol
36
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
3.4 Copper Ethernet Port Specifications
The RSG2288 can be ordered with two-port 10/100/1000Tx modules in slots 1, 2,
3, and 4, and a one-port 10/100/1000Tx module in 5. All copper ports have the
following specifications:
Parameter
Speed
Specification
Notes
10/100/1000 Mbps
FDX / HDX
> Category 5
TIA/EIA T568A/B
100m
Auto-negotiating
Auto-negotiating
Duplex
Cable-Type
Wiring Standard
Max Distance
Connector
Isolation
Shielded/Unshielded
Auto-Crossover, Auto-Polarity
RJ45
1.5kV
RMS 1-minute
3.5 Fiber Ethernet Optic Specifications
The following sections detail fiber optical specifications on ports that can be
ordered with a RSG2200 series Ethernet switch. The user determines the type of
optics at time of ordering, and can determine the modules installed on a
particular unit by reading the factory data file via the ROS® user interface.
Sections 3.5.1 and 3.5.2 list the specifications of the optical transceivers used in
the fiber Ethernet modules available for the RSG2288. The specifications are
organized by signaling speed and then by order code. Module order codes are
contained within each product when assembled and configured at the factory.
Consult the RuggedCom ROS User Guide for help in obtaining the factory
configuration data.
3.5.1 Fast Ethernet (100Mbps) Optical Specifications
Rx
Rx
Distance
(typ.)
(km)
Power
Budget
(dB)
Order
Code
Connector
Type
Cable Type
(um)
Tx λ (typ.)
(nm)
Tx min Tx max
Mode
Sensitivity Saturation
(dBm)
(dBm)
(dBm)
(dBm)
62.5/125
50/125
62.5/125
50/125
9/125
-19
-22.5
-19
12
8.5
12
8.5
13
12
8.5
17
16
19
29
30
FXA01 MM
ST
1300
1300
-14
-31
-14
2
2
FXA02 MM
FXA11 MM
SC
LC
-14
-31
-14
-22.5
-19
1300
1300
-14
-14
-32
-31
-14
-14
2
2
62.5/125
50/125
9/125
-19
FXA03 MM MTRJ
-22.5
-15
FXA04 SM
FXA05 SM
FXA06 SM
FXA07 SM
FXA08 SM
ST
SC
LC
SC
LC
1310
1310
1310
1310
1310
-8
-8
-8
0
-32
-31
-34
-34
-35
-3
-7
-7
-3
-3
20
20
20
50
50
9/125
-15
9/125
-15
9/125
-5
9/125
-5
0
37
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
FXA09 SM
FXA10 SM
SC
LC
9/125
9/125
1310
1310
0
0
5
5
-37
-37
0
0
90
90
37
37
3.5.2 Gigabit Ethernet (1000Mbps) Optical Specifications
Fixed Gigabit Transceivers
Rx
Rx
Distance
(typ.)
(km)
Power
Budget
(dB)
Order
Code
Connector
Type
Cable Type
(um)
Tx λ (typ.)
(nm)
Tx min Tx max
Mode
Sensitivity Saturation
(dBm)
(dBm)
(dBm)
(dBm)
50/125
62.5/125
9/125
FG01 MM
LC
850
-9
-2.5
-20
0
0.5
11
FG02 SM
FG03 SM
FG04 SM
FG05 SM
SC
LC
SC
LC
1310
1310
1310
1310
-10
-9.5
-5
-3
-3
0
-20
-21
-20
-24
-3
-3
-3
-3
10
10
25
25
10
11.5
15
9/125
9/125
9/125
-7
-3
17
SFP Gigabit Transceivers
Rx
Rx
Distance
(typ.)
(km)
Power
Budget
(dB)
Order
Code
Connector
Type
Cable Type
(um)
Tx λ (typ.)
(nm)
Tx min Tx max
Mode
Sensitivity Saturation
(dBm)
(dBm)
(dBm)
(dBm)
50/125
62.5/125
9/125
9/125
9/125
0.5
0.3
10
25
70
FG51 MM
LC
850
-9
-2.5
-20
0
11
FG52 SM
FG53 SM
FG543 SM
LC
LC
LC
1310
1310
1550
-9.5
-7
0
-3
-3
5
-19
-23
-23
-3
-3
-3
9.5
16
23
GBIC Gigabit transceivers
Rx
Rx
Distance
(typ.)
(km)
Power
Budget
(dB)
Order
Code
Connector
Type
Cable Type
(um)
Tx λ (typ.)
(nm)
Tx min Tx max
Mode
Sensitivity Saturation
(dBm)
(dBm)
(dBm)
(dBm)
FG71 SM
FG72 SM
FG733 SM
SC
SC
SC
9/125
9/125
9/125
1310
1310
1550
-9.5
-7
-3
-3
5
-21
-3
10
25
70
11.5
17
-24
-23
-3
-3
0
23
Notes:
1. Maximum segment length is greatly dependent on factors such as fiber
quality, and number of patches and splices. Please consult RuggedCom
sales associates when determining maximum segment distances.
2. Distance ratings are typical but will depend on type of cabling, number of
connectors and splices.
3. These transceivers have an operating temperature range of -20°C to +85°C.
All other transceivers have an operating temperature range of -40°C to
+85°C.
4. All optical power figures are listed as dBm averages.
38
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
3.6 PTP Card Specifications
IRIG-B PWM Input
Parameter
Input Voltage
Typical Value
TTL-Compatible
Input Impedance
> 200 kΩ
3.6.1 IRIG-B Outputs
IRIG-B003 PWM Output
Parameter
Typical Value
100 mA
5 Vp-p
Output Current (IS)
Output Voltage (VS)
Output Impedance (RS)
50 Ω
Table 15: IRIG-B PWM Output Specifications
IRIG-B123 AM Output
Parameter
Typical Value
1 kHz
Carrier Frequency
Modulation Depth
Output Current (IS)
Output Impedance (RS)
Output Voltage (VS)
3:1 ±10%
24 mA
10 Ω
6 Vp-p
Table 16: IRIG-B AM Output Specifications
3.7 Operating Environment
Parameter
Range
Comments
Ambient Temperature as
measured from a 30cm radius
surrounding the center of the
enclosure.
Ambient Operating
Temperature
-40 to 85C
Ambient Relative
Humidity
5% to 95%
Non-condensing
Ambient Storage
Temperature
-40 to 85C
39
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
3.8 Mechanical Specifications
Parameter
Dimensions
Value
Comments
(Length x Width x Height)
with mounting brackets
installed
18.29 x 12.14 x 1.75 inches
(464,57) x (308,356) x (44,45)
mm
Weight
10 lb (4.5 Kg)
Enclosure
18AWG galvanized steel
Figure 32: RSG2288 Mechanical Dimensions
40
RuggedSwitch® RSG2288 Installation Guide rev103
RuggedCom®
Download from Www.Somanuals.com. All Manuals Search And Download.
Type Tests
4 Type Tests
4.1 IEC 61850-3 Type Tests
Severity
Levels
Test
Description
Enclosure Contact
Test Levels
+/- 8kV
+/- 15kV
4
4
x
x
4
4
4
IEC 61000-4-2
IEC 61000-4-3
ESD
Enclosure Air
Enclosure ports
Signal ports
Radiated RFI
20 V/m
+/- 4kV @ 2.5kHz
+/- 4kV
D.C. Power ports
A.C. Power ports
Earth ground ports
Burst (Fast
Transient)
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
+/- 4kV
+/- 4kV
+/- 4kV line-to-earth, +/- 2kV line-to-
Signal ports
4
3
4
line
+/- 2kV line-to-earth, +/- 1kV line-to-
Surge
D.C. Power ports
A.C. Power ports
line
+/- 4kV line-to-earth, +/- 2kV line-to-
line
Signal ports
10V
10V
10V
10V
3
3
3
3
Induced
(Conducted)
RFI
D.C Power ports
A.C. Power ports
Earth ground ports
Magnetic
Field
IEC 61000-4-8
IEC 61000-4-29
IEC 61000-4-11
Enclosure ports
D.C. Power ports
40 A/m continuous, 1000 A/m for 1 s
N/A
30% for 0.1s, 60% for 0.1s, 100% for
0.05s
30% for 1 period, 60% for 50 periods
100% for 5 periods, 100% for 50
periods 2
N/A
N/A
N/A
Voltage Dips
& Interrupts
A.C. Power ports
2.5kV common, 1kV differential mode
@ 1MHz
2.5kV common, 1kV differential mode
@ 1MHz
Signal ports
3
3
Damped
Oscillatory
IEC 61000-4-12
D.C. Power ports
2.5kV common, 1kV differential mode
@ 1MHz
A.C. Power ports
Signal ports
3
4
4
Mains
Frequency
Voltage
Ripple on
D.C. Power
Supply
30V Continuous, 300V for 1s
IEC 61000-4-16
IEC 61000-4-17
IEC 60255-5
D.C. Power ports
30V Continuous, 300V for 1s
D.C. Power ports
10%
3
Signal ports
D.C. Power ports
A.C. Power ports
Signal ports
D.C. Power ports
A.C. Power ports
2kV AC (Fail-Safe Relay output)
N/A
N/A
N/A
N/A
N/A
N/A
Dielectric
Strength
1.5kVDC
2kVAC
5kV (Fail-Safe Relay output)
IEC 60255-5
H.V. Impulse
5kV
5kV
Table 17 - IEC 61850-3 Type Tests
41
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Type Tests
4.2 IEEE 1613 Type Tests
IEEE
IEEE Test
1613
Description
Test Levels
Clause
Enclosure Contact
+/- 8kV
C37.90.3
C37.90.2
9
8
ESD
Enclosure Air
Enclosure ports
Signal ports
+/- 15kV
Radiated RFI
35 V/m
+/- 4kV @ 2.5kHz
D.C. Power ports
A.C. Power ports
Earth ground ports
Signal ports
+/- 4kV
C37.90.1
7
Fast Transient
+/- 4kV
+/- 4kV
2.5kV common mode @ 1MHz
C37.90.1
C37.90
C37.90
7
6
6
Oscillatory
D.C. Power ports
A.C. Power ports
Signal ports
D.C. Power ports
A.C. Power ports
Signal ports
2.5kV common & differential mode @ 1MHz
2.5kV common & differential mode @ 1MHz
5 kV (Failsafe Relay)
H.V. Impulse
5 kV
5 kV
2kVAC
1.5kVDC
Dielectric
Strength
D.C. Power ports
A.C. Power ports
2kVAC
Table 18 - IEEE 1613 Type Tests
Notes:
If the unit contains copper ports, the IEEE 1613 conformance is Class 1 (During
disturbance errors may occur but recovery is automatic).
If the unit contains all fiber ports, the IEEE 1613 conformance is Class 2 (During
disturbance no errors will occur).
4.3 IEC Environmental Type Tests
Severity
Levels
Test
Description
Cold
Test Levels
IEC 60068-2-1
IEC 60068-2-2
IEC 60068-2-30
IEC 60255-21-1
IEC 60255-21-2
Test Ad
Test Bd
Test Db
-40 deg. C, 16 Hours
+85 deg. C, 16 Hours
N/A
N/A
Temperature
Dry Heat
Humidity (Damp
Heat, Cyclic)
95% (non-condensing), 55°C, 6
cycles
N/A
Vibration
Shock
2g @ (10-150) Hz
30g @ 11 ms
Class 2
Class 2
Table 19 - Environmental Type Tests
Note:
Class 2 refers to “Measuring relays and protection equipment for which a very high
security margin is required or where the vibration levels are very high, (e.g. shipboard
application and for severe transportation conditions).”
42
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
Agency Approvals
5 Agency Approvals
Agency
Standards
Comments
CSA
CSA C22.2 No. 60950, UL 60950
Passed
CE Compliance is
claimed via Declaration
of Self Conformity
Route
CE
EN 60950, EN 61000-6-2
FCC
CISPR
FCC Part 15, Class A
EN55022, Class A
Passed
Passed
Passed
FDA/CDRH
21 CFR Chapter 1, Subchapter J
EN60825-1:1994 + A11:1996 +
A2:2001
IEC/EN
Passed
6 Warranty
RuggedCom warrants this product for a period of five (5) years from date of
purchase. This product contains no user-serviceable parts. Attempted service by
unauthorized personnel shall render all warranties null and void. For warranty
representative.
Should this product require warranty or service, contact the factory at:
RuggedCom Inc.
300 Applewood Crescent
Concord, Ontario
Canada L4K 5C7
Phone:+1 905 856 5288
Fax: +1 905 856 1995
43
RuggedCom®
RuggedSwitch® RSG2288 Installation Guide rev103
Download from Www.Somanuals.com. All Manuals Search And Download.
|