|
Cover for IDC™ 150TII
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IDC™ 150TII
TM
®
Congratulations on your purchase of the IDC™ 150TII. The IDC™ 150TII power amplifier is a three rack
space, solid state, mono power amplifier capable of delivering more than 150 W RMS. The unit has been designed to
be reliable, meeting the needs of most fixed installation applications. One of the most significant features of this
amplifier is its battery backup capability. This amplifier will operate with a 24 V DC external power source as well as
120 V AC power. This means if the AC power mains are lost, the amplifier can still function.
Fully isolated 25 volt and 70 volt line output capabilities are provided with this amplifier. SPS™ compression
is also provided to help eliminate distortion due to clipping. A balanced 600 ohm line out is available to provide signal
to additional amplifiers.
FRONT PANEL FEATURES:
SPS™ LED INDICATOR (1)
When the SPS™ compression is active, this indicator illuminates to show that the amplifier is being overdriven to the
point that the signal runs out of headroom.
POWER LED INDICATORS: MAINS (2) & 24 V DC (3)
Mains: Illuminates green when AC main power is supplied to the amplifier and the main power switch is turned on.
24 V DC: Illuminates red when the DC power is connected and the power switch turned on.
AC POWER SWITCH (4)
Depress to “on” position to turn on amplifier.
DC POWER SWITCH (5)
Depress to “on” position to enable DC backup power.
Note: With both AC and DC power switches turned on and sufficient AC voltage being supplied, the amplifier does not
draw any current from the DC supply.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel:
BACK PANEL FEATURES:
FUSE (6)
WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS
BEEN DISCONNECTED FROM ITS POWER SOURCE.
CAUTION: USING A FUSE LARGER THAN THE RECOMMENDED SIZE COULD
RESULT IN PERMANENT DAMAGE TO THE AMPLIFIER.
The fuse is located within the cap of the fuseholder. If the fuse should fail, IT MUST BE REPLACED
WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT
AND TO PREVENT VOIDING THE WARRANTY. If the unit repeatedly blows fuses, it should be
taken to a qualified service center for repair.
INPUT SENSITIVITY CONTROLS (7)
Maximum input gain (minimum sensitivity rating) is achieved at full clockwise setting. This setting yields maximum
mixer/system headroom. A setting of less than one full clockwise turn will yield lower system noise at the expense of
mixer/system headroom.
AMPLIFIER INPUTS (8)
The terminal strip is configured to allow balanced or unbalanced input signals. When using an unbalanced input signal,
a jumper wire should be placed between the ( - ) and GND terminals.
LINE OUTPUT (9)
This terminal strip is provided to drive the input of other amplifiers. It is a balanced 600 ohm line output.
MATRIX (10)
This jack is to be used with Peavey’s MediaMatrix system. This allows for remote status and control of the amplifier or
several amplifiers.
DC POWER CONNECTOR (11)
This terminal strip should be connected to a battery backup DC power supply with a voltage of approximately
24 V DC. It is important to correctly wire this so that the positive terminal is connected to the positive side of the
battery. An improper connection can result in damage to the battery and/or the amplifier.
AMPLIFIER OUTPUTS (12)
Fully isolated terminal strip is provided for 25 volt and 70 volt line outputs. When using the 25 volt line output the load
impedance should be 4 ohm and when using the 70 volt line output an impedance of approximately 33 ohms is recom-
mended.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INFORMATION: POWER HANDLING AND GROUNDING
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to
remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding
facilities, suitable grounding adapters should be used. Less noise and greatly reduced shock hazard exists when the unit
is operated with the proper grounded receptacles.
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The power amplifier shall have one input with provisions for balanced and unbalanced signals via terminal strip. A
600 ohm balanced line output shall be provided, also via terminal strip. The amplifier shall be capable of delivering
150 watts into 4 ohms at the 25 volt line output, and 150 watts into 33 ohms at the 70 volt line output. This unit shall
have the capability of continuously operating if the AC mains are lost, due to its battery backup circuit (the battery must
be provided). This amplifier shall be compatible with Peavey’s MediaMatrix system, providing a jack for easy hook up
and operation. This amplifier must have a signal-to-noise ratio of at least 100 dB below rated output. The unit shall be
called the Peavey Architectural Acoustics Division model IDC™ 150TII.
LIMITED WARRANTY
Peavey Electronics Corporation warrants to the original purchaser of this new Architectural Acoustics product that it is
free from defects in material and workmanship. If within one (1) year from date of purchase a properly installed
product proves to be defective and Peavey is notified, Peavey will repair or replace it at no charge. (Note: Batteries and
patch cords not covered.) “Original purchaser” means the customer for whom the product is originally installed.
Damage resulting from improper installation, interconnection of a unit or system of another manufacturer, accident or
unreasonable use, neglect or any other cause not arising from defects in material and workmanship is not covered by
this warranty. The warranty is valid only as to products purchased and installed in the United States and Canada.
THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
USE. UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS,
INCIDENTAL DAMAGES OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
THIS LIMITED WARRANTY IS THE ONLY EXPRESSED WARRANTY ON THIS PRODUCT, AND NO OTHER
STATEMENT, REPRESENTATION, WARRANTY, OR AGREEMENT BY ANY PERSON SHALL BE VALID OR
BINDING UPON PEAVEY.
Peavey’s liability to the original purchaser for damages for any cause whatsoever and regardless of the form of action is
limited to the actual damages up to the greater of Five Hundred Dollars ($500) or an amount equal to the purchase price
of the product that caused the damage or that is the subject of or is directly related to the cause of action. This limitation
of liability will not apply to claims for personal injury or damage to real property or tangible personal property alleg-
edly caused by Peavey’s negligence. For information on service under this warranty, call a Peavey customer service
representative at (601) 483-5376.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
(all measurements @ 120 V AC, 60 Hz or 24 V DC)
Rated Output Power: (typical value)
Input Sensitivity:
AC powered, continuous sine wave:
(FCW attenuator setting)
70 volt line 32.7 ohms, 1 kHz, 1% THD: 150 W RMS
25 volt line 4.2 ohms, 1 kHz, 1% THD: 150 W RMS
150 W RMS, rated output power
Input voltage: 1.1 V RMS
24 V DC battery powered, continuous sine wave:
70 volt 32.7 ohms, 1 kHz, 1% THD: 100 W RMS
25 volt 4.2 ohms, 1 kHz, 1% THD: 100 W RMS
Voltage Gain:
dBV 27 db
Dimensions & Weight:
Height: 5.25" (13.3cm)
Width: 19" (48.3cm)
Depth: 13" (43.2cm)
Weight: 32 lbs.
Frequency Response: (typical value)
(SPS eliminated)
100 W RMS: +0, -1 db, 20 Hz to 15 kHz
Total Harmonic Distortion:
300 kHz bandwidth measurement; AC powered
(100 W RMS, 70 volt and 25 volt lines)
20 Hz to 15 kHz, below 0.15% THD
Protection Systems:
Thermal shutdown 100° C
Current/Voltage limiting
Crowbar, on output to protect speakers from DC
Signal-To-Noise Ratio:
(unweighted, 20 Hz to 22 kHz; FCW attenuator setting)
S/N below 103 db
Power Consumption:
Domestic model:
120 V AC, 60 Hz, 5 A, 600 W
24 V DC, 7 A
Slew Rate: (typical value)
10 V/µs
Export model:
230 V AC, 50 Hz, 2.6 A, 600 W
Damping Factor: (typical value)
25 volt line; 1 kHz: 50
70 volt line; 1 kHz: 100
Input Impedance:
(FCW attenuator setting)
Balanced:
10 k ohms
Unbalanced: 10 k ohms
TM
®
Due to our efforts for constant improvements,
features and specifications listed herein are subject to change without notice.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic cautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
Read all safety and operating instructions before using this product.
All safety and operating instructions should be retained for future reference.
Obey all cautions in the operating instructions and on the back of the unit.
All operating instructions should be followed.
This product should not be used near water, i.e., a bathtub, sink, swimming pool, wet basement, etc.
This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a
wall or placed in a built-in enclosure that will impede the flow of cooling air.
7.
8.
9.
This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier.
Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet “Shock
Hazard and Grounding.”
10. Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically check
cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit.
11. The power supply cord should be unplugged when the unit is to be unused for long periods of time.
12. If this product is to be mounted in an equipment rack, rear support should be provided.
13. Metal parts can be cleaned with a damp rag. The vinyl covering used on some units can be cleaned with a damp rag or an ammonia-
based household cleaner if necessary. Disconnect unit from power supply before cleaning.
14. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation holes or any other
openings.
15. This unit should be checked by a qualified service technician if:
a. The power supply cord or plug has been damaged.
b. Anything has fallen or been spilled into the unit.
c. The unit does not operate correctly.
d. The unit has been dropped or the enclosure damaged.
16. The user should not attempt to service this equipment. All service work should be done by a qualified service technician.
17. This product should be used only with a cart or stand that is recommended by Peavey Electronics.
18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise
induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level
exposures.
Duration Per Day In Hours
Sound Level dBA, Slow Response
8
6
90
92
4
95
3
97
2
1 1/2
1
1/2
1/4 or less
100
102
105
110
115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss.
Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a
permanent hearing loss if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high
sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as
this amplification system be protected by hearing protectors while this unit is in operation.
SAVE THESE INSTRUCTIONS!
®
ARCHITECTURAL ACOUS TICS
®
Features and specifications subject to change without notice.
A Division of Peavey Electronics Corporation
711 A Street / Meridian, MS 39301 / U.S.A. / (601) 483-5376 / Fax 486-1278
#80302291
®
©1995
Printed in U.S.A. 12/95
Download from Www.Somanuals.com. All Manuals Search And Download.
|