Specification
WARNING
warning
Please remember the model Number
LCD
Model
5"TFT
MODEL NUMBER
SERIES NUMBER
and series number if you need.
And please check all accessories
when you drop the carton package
Input signal
video
component video(Ypbpr) ,VGA HDMI
TV
audio
audio
stereo
When you use this projector , please read this manual carefully
output signal
LCD
5W 2 speaker(select)
Donot see the light from the lens ,it is high bright lamp.
It will damage your eye .specially for chirdren.
native resolution 640 480 support 576P, 720P 1080P)
contrast ratio 800
1
Warning:Donot place the projector in the wet condition,
avoid to getting an electric shock
Lens
aperture
Focus
3.8
160mm
Lamp
Power
150W
It indicates there is a instruction
for important operation
High Voltage,donot open it ,
except for professiona
Color-Temperature
Life > 6000 hours
working time < 24 hours
9300K
WARNING
It indicates there is a dangerous
voltage
Image
Power
size
60 100inch
1800 Lumens
20 degree
Brightness
keystone
Voltage
220 10 VAC 50Hz or 110 10 VAC 60Hz
power consumption
< 200W
Warning
when close the projector ,the fans will continue to turn 90seconds.
Before pull out the power cable, please be sure the fans stop to turn .
Or it will damage the projector lamp
Working condifition
temperature
humidity
0
+70
65
10
store condition
temperature
humidity
-20
10
+70
90
About the remote control battery:
The remote control battery should be fixed correctly ,
Or it will damage the remote control.
Remote control Frequency
38KHz
machine
size
298 210 120mm
6Kg
Make sure the remote control out of chirdren reach
weight
If all parameter changed,donot note again
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Trouble shooting
Warning;
when use this projector ,please read this manual carefully.
If wrong operation ,it will cause electric shock or fire.so when use
and repair this projector ,please comply with the following points
TROUBLE SHOOTING
Please refer to this chapter when you encounter a problem list prior to contacting your
dealer.
9,protect the power cable
Please confirm the power cable
are perfect when connect the
projector.
1,Read manual
Before use this projector ,please
read full manual carefully and
operate according to this manual instruction
Problem:
Possible solution(s):
Projector turns off automatically
1, Dust cover the filter ,
10,Thunder
2,Clear
Please wash this filter by water .
when the thunder happen or long time
no use , please pull the power cable
out of projector.
when clear this projector ,please pull
out the power cable. Use the wet cloth
to clear,not the cleasner
2, Some of fans are broken ,donot turn again,
It is high temperature protected system.
Please replace the broken fans quickly.
11,Repairment
3.Accessory
As the high voltage inside ,please
donot open or try to repair the
projector by yourself. . Please ask a
professional technician to repair
the projector.
please use our recommended accessory.
Or it will damage the projector.
4,Use environment
Lamp doesn't work.
1, Power supplier are wrong . Please confirm your
Projector power specification . 220V or 110V .
Donot place the projector in wet environment
5,installation and fix
2 , Lamp are broken or out of service life.
Please replace the lamp and test it again
12, Far away Heat device
please make sure this projector far
away other heat device . It will
damage the projector service life
please place this projector in stable table .
6, Ventilation
3, Check the ignitor . It is broken , please change a
New ignitor.
the ventilation in the projector are best
for projector work stably. Donot let the dust
wall up the filter. Or it will cause the projector
high-temperature protected. So please use the
water to clear the filter per month.
7, Power
please make sure the power same as your
projector inquiry specification. (220 V or 110V)
8, Earthing wire
this projector has earthing wire .
It is three pin plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Caution
About the installation
TROUBLE SHOOTING
About Open and close the projector
In order to improve the projector service life,
It shouldnot place in a wet and
ventilation condition
Please refer to this chapter when you encounter a problem list prior
to contacting your dealer.
when open the projector ,connect
the power cable and press the "power"
key on the panel .the projector will
work ,but the lamp will be bright more
and more .After 5 minutes, the lamp wor
normally
Donot put the projector under the sunshine
directly
Problem:
Possible solution(s):
Projector working temperature: 0
Projector store temperature : -20
+70
+70
No power
1, The projector donot connect the power cable
2, Donot open the projector .
3, Fuse broken
when close the projector , press the powe
key again . And then the lamp shut off.
But the fans still work until 5minutes late
When close the projector ,donot pull out
the power cable directly . After 5minutes
the projector will shut off automatically.
Donot block the ventilation-window
of projector
If the projector interior temperature
are too hot , the machine will be shut
off automatically.This is hot -
protected system.
Remote doesn't operate
1,Projector turned on to quickly after
last turn off (needs 5 minutes).
So please clean the filter of projector
per month . It is very important.
Donot let the dust cover the filter.
2,Batteries defect.
3, Aim remote correctly at IR receiver.
1, Please remove the len cap at first
2, Projector turned off.
No image
Warning
3, Selected the wrong input signal.
Fans will adjust the temperature It is controlled by system when the projector work,
the fans turn slowly or quickly so the fans noise are different But it is normal
when the projector work ,donot pull out the pwer cable If the fans stop to work,it will cause
the projector interior temperature very high, so it may damage the projector.
4, the mainboard are broken . Please
Replace this mainboard.
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Installation
PROJECTOR INSTALLATION
Please use the setup instruction below:
2.Take away the panel like the picture 2
Speaker
L
Speaker
R
Screen
Subwoofer
Speaker C
DVD
Projector
Amplifier
Appreciate seats
Door
Speaker
Ls
Speaker
Rs
Before replacing the lamp,make sure the lamp are cold
Before open the lamp cover board,pull out the power cable
When replacing the lamp,donot drop some dirty goods
inside the projector.
In order to get good image quality ,donot let the sunlight shine
the screen directly .If you use the projector in the day time,
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Replace the projector lamp
Projector Installation
Standard setting Front projection
Please refer to the following sheet , adjust your picture size
and distance (from the lens to screen )
Our projector lamp warranty 6 months In different use environment
after 6000hours the lamp brightness will reduce the image will
become dark .Therefore please replace the lamp according to
the following steps
Taille D' cran
4:3
16:9
50"
72"
2.45m
3.45m
4.73m
2.65m
3.75m
5.15m
1, use the tool to remove the screw,like the picture 1 show
100"
The data maybe have 3% error,due to the image size according
to the distance between projector and screen if the distance is
less 2m or over 5m,the image maybe not clear.
warning
Please check the following picture to show the trapezoid adjustment
Screen
Screen
symmetry
axis
Projector
Installed correctly,
the image is rectangular.
Incorrect installation,
the images left-right small.
Incorrect installation,
the images right-left small.
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Projector installation
Maintenance filter
Installation method:
The filter should be cleaned at least once a month (more often
in dusty environments),or the projector will overheat
the step as follow
Contact a proffessional service man to mount this projector to a ceiling.
Follow the instructions belowe for the correct projector positions:
projector
screen
projector
screen
1.Remove the grille like indicated below
Front projection
ceiling mount
Rear projection
Ceiling mount
screen
projector
projector
screen
Front projection
Table mount
Rear projection
Table mount
Warning
1
This projector might damage beyond repair when it is incorrectly mounted on
a ceiling or when its incorrectly installed on a surface or installed on a
incorrect surface. It may also inflict damage to persons within close vicinity.
2)This projector can only be used in an environment with a temperature not
exceeding the range of 0- 35 degree .The projector may malfunction if
temperatures vary outside the normal operating range.
3
The sharpness of the screen might be interrupted when the
2. clear the dusty on the filter Dry the filter sufficiently
neverinstall a moist filter in this projector,and complete
the installation
projector is being used in a dusty,wet,moist or smoke filled
environment. The projector might malfunction in a moist or wet
environment.
4
Take care of sufficient ventilation around the projector.
Otherwise this projecctor might overheat and cause life threatening
situations
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector installation
Menu setting
Input port instruction
This projector can support component video signal, s-video signal,VGA
signal and TV signal,the audio in and audio out function.
•
•
SOUND
ADVANCE
EOUALIZER
BALANCE
SLEEP TIMER
OFF
ON
SOUND MODE
AVC
STANDARD
OFF
OFF
SURROUND
AUDIO OUTPUT
NORMAL
MENU
: EXIT
: MOVE
: AD J
MENU : EXIT
: MOVE
: AD J
•
•
• •
•
•
• •
• •
•
•
SYSTEM
PIP
OSD LANGUAGE
OSD H POSITION
OSD V POSITION
OSD DURATION
OSD HALFTONE
H FLIP
ENGLISH
PIP
TV
LARGE
MULITI WINDOW
SUB SOURCE
SIZE
PIP H.POSITION
PIP V.POSITION
BORDER COLOR
SOUND SOURCE
SWAP
7. Signal wire connect
1. Indicator light
4
42
4
connect projector signal source
read the signal port introduce
8. Power switch
OFF
OFF
BLACK
MAIN
on stay situation the light is red
on working situation the light is green
2. Panel key
V FLIP
: MOVE
: AD J
MENU : EXIT
: MOVE
: AD J
MENU : EXIT
when use ,you need connect the
power wire with projector and
the power jace
use panel key to adjust parameter
read the introduce of the panel key
3. Remote control receiver
9. Fuse
if open the power switch,the indicator
light donot work,it maybe the fuse
when use the remote control,please
point this receiver directly
broken
5A220V)
4. Lens
10. Power switch
adjust the lens focus to improve
the image quality
open and shut off this switch
when you want to open the projector
it must open this switch at frist
11. ventilation
5. Trapezoid correction
GEOMETRY
TV
turn the knob on the projector left or right .
H.POSITION
V.POSITION
CLOCK
AUTO SCAN
MTS
SKIP
Adjust the image become square,can adjust +/-15
MO N O
ON
this ventlilation window is very important
donot block this window.otherwise
it will burn the projector
PHASE
98
FINE TUNING
MANUAL SEARCH
COLOR SYSTEM
SOUND SYSTM
6. HDMI signal input , max support 1080i signal.
AUTO
12. ventilation
: MOVE
: AD J
MENU : EXIT
: MOVE
: AD J
MENU : EXIT
two side of the projector have the ventilation
when use ,you must ensure do not block it
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector install
Menu setting
Menu setting method
1. Using the projector press menu key,
the picture disply on screnn to adjust the
menu(picture one)
Picture
• • • • • • ••• • •• • •• • • •• •• ••• •• • •• • • •
••• • • •• •• • •• • •• • • •
CONTRAST
BRIGHTNESS
HUE
2. press
key the menu in turn
SATURATION
SHARPNESS
COLOR TEMP
SCALE
PICTURE MODE
3D NR
MPEG NR
: MOVE
STANDARD
3
circle into image
>
volume
setting
>
4
function
image adjust interface
3. Elect the adjust interface use
elect the item that need to adjust(picture two
>
system
>
>
MID
HIGH
: AD J
MENU : EXIT
key
4. use
key to adjust the elect item paremeter
5. Finished the elect item parameter press the
menu key again exit the page
Picture
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
COLOR TEMP
SCALE
PICTURE MODE
3D NR
MPEG NR
: MOVE
6. Repeat operate the 2 5step
till finished all the parameter's enactment
press exit key,exit the menu page
otherwise the menu page will auto exit
after a period time
STANDARD
4
3
MID
HIGH
: AD J
MENU : EXIT
Connecting video equipment
Without S-video output terminal.
1. Image menu adjustment
a. Press menu key untile disply the
above picture of the menu
• • • •• • • • • • •
b. Press
that need to adjust
c. Press
key elect the option
Picture
CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
COLOR TEMP
SCALE
key adjust
parallelisn elect parameter.
STANDARD
4
3
d. Press the "menu" key again exit
PICTURE MODE
3D NR
MPEG NR
: MOVE
MID
HIGH
the menu page parameter adjust station.
: AD J
MENU : EXIT
• •
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control instruction
Image adjustment
Remote panel instruction
The new projector using it first time commonly will
appear image faintness and the the image is trapezoid it is course
that not adjust well of the lens focus and the trapezoid
please follow the step the correction
16 :9/4 :3 switch key
switch the display picture for 16 :9 or4 :3
Focus adjustment
Power
for turn the power on.
ute
open or close the volume
MUTE
ON/OFF
•
turn the lens into the projector then turn it out slowly
at the same time looking at the resolution point carefully
when the image is very clearly (take the middle area of the image),it is the
best situation of the lens
16:9/4:3
• • •• • •• • • •• • • • ••• • • ••• • • • •
••• • ••• • ••• • ••• • • ••• •• • • •
AV
SV
VGA HDMI
YPbPr
ATV
DTV
SCART
H.Flip V.Flip
Preview Picture
MODE
Image effect reset key
can set the image brightness,
soft colour or personality
quickly in turn
Display
PIP
OK
menu mode .adjust patameter
• • • • ••• •
DTV
M
• • • • •• •••• ••••
•• • •• • •• • • •• ••• • • •
DTV Menu
Menu
RE
EPG
TEXT
Return
REVEAL
INDEX
NOTE: When you replace the projector from a cold to a warm environment water vapour
might occur. Don't turn the projector on when this occurs but wait until the vapour
has disappeared.
SUBPage
SIZE
1
2
5
8
0
3
4
7
6
0
KEYSTONE
Number Buttons
-/--
If a projected picture has keystone distortion, correct image with Keystone adjustment. The
image becomes trapezoid shape when the screen or project is not level. Please reposition
the projector to improve its angle to the screen. However, the circumference of the image
may not be focussed.
selects TV channel directly
UP
DOWN
MIX
HOLD
Projector
Precautions
1
you need to dry the remote control with a dry cloth immediately
when it gets wet.
Projector
Screen
Screen
Keystone
2, when the battery hasn't been used for a long time we advise you to
remove it from the remote .be sure that children can't reach the
removed button cell .swallowing a of harm and is very dangerous
If not able to use the Keystone correction function to correct the trapezoid distortion, please
reduce of the projector to centre the screen vertically.
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel keystoke instruction
Panel keystoke sketch map
If the projector is the new one please read projector install
chapter placed the projector connect the powerwire and the signelwire
the operation as follow:
Open operation
1.Before use the remoter .
Put in two 7 size battery in it
2. Open the power switch on the backboard
the power light begin to flash
press the power key on the remote control or panel
the indicator light turn light
Power key
•
•
After 2 second the projector lamp begin work
began appear unclear white light on the screen
after 2 minute,the projector begin work
Menu,direction Key
It can open or close the projector
its function same as the "power"
in the remote control
It can adjust the menu by
UP/Down ,left/righ
•
Indicator light
5. For the new projector. When the frist time to use maybe will appear image
PC/AV Key
unclear or trapezoid distortion please read image adjustment chapter
It can choose the input signal
(such as: AV.SVIDEO .Component video ,
HDMI,PC or TV)
6. After the image is clear then you can watch program during watching
you also can setup the system parameter please read menu setting chapter
Close operation
1.During use the projector press power key can let the projector
switch to stay situation
2.After inter into stay situation the projector under auto protect auto release hot
the indicator light is flase situation but here the projector is under auto protect
situation not accept any order if need to startup again must wait for finished
the release hot .
Download from Www.Somanuals.com. All Manuals Search And Download.
|
