Porter Cable Drill D22722 028 3 User Manual

ESPAÑOL: PÁGINA 9  
FRANÇAIS: PAGE 17  
Instruction manual  
Manual de  
Instrucciones  
1/2" Reversible Drill  
Manuel d'instructions  
Taladro Reversible  
de 1/2"  
Perceuse réversible de  
1/2 po  
MODEL  
PTD501  
MODELO  
PTD501  
MODÈLE PTD501  
To learn more about Porter-Cable visit  
our website at:  
IMPORTANT  
Para obtener más información sobre  
Porter-Cable, visite nuestro sitio web en:  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
Pour de plus amples renseignements  
concernant Porter-Cable, consultez  
notre site Web à l'adresse suivante:  
IMPORTANTE  
Asegúrese de que la persona que va a usar esta  
herramienta lea cuidadosamente y comprenda  
estas instrucciones antes de empezar  
operarla.  
a
IMPORTANT  
Veuillez vous assurer que la personne qui  
utilise cet outil lit attentivement et comprend  
ces instructions avant de commencer à utiliser  
l'outil.  
Copyright © 2002 Porter-Cable Corporation  
Part No. D22722-028-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HAZARD  
RISK OF LOSS OF HEARING  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Long term exposure to noise produced from the opera-  
tion of air tools can lead to permanent hearing loss.  
Always wear ANSI S3.19 hearing protection.  
HAZARD  
RISK TO BREATHING INHALATION HAZARD  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Abrasive tools, such as grinders, sanders, and cut-off  
tools generate dust and abrasive materials which can  
be harmful to human lungs and respiratory system.  
Always wear MSHA/NIOSH approved, properly fitting  
face mask or respirator when using such tools.  
Some materials such as adhesives and tar, contain  
chemicals whose vapors could cause serious injury  
with prolonged exposure.  
Always work in a clean, dry, well ventilated area.  
HAZARD  
RISK OF INJURY  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Remove air hose when tool is not in use and store tool  
in secure location away from reach of children and or  
untrained users.  
Tools left unattended, or with the air hose attached can  
be activated by unauthorized persons leading to their  
injury or injury to others.  
Air tools can propel fasteners or other materials  
throughout the work area.  
Use only parts, fasteners, and accessories  
recommended by the manufacturer.  
Keep work area clean and free of clutter. Keep children  
and others away from work area during operation of  
the tool.  
Keep work area well lit.  
Remove adjusting keys and wrenches before turning  
the tool on.  
A wrench or a key that is left attached to a rotating part  
of the tool increases the risk of personal injury.  
Using inflator nozzles for duster applications can cause  
serious injury.  
DO NOT use inflator nozzles for duster applications.  
Air tools can become activated by accident during  
maintenance or tool changes.  
Remove air hose to lubricate or add grinding  
attachments, sanding discs, drills, etc. to the tool.  
Never carry the tool by the hose.  
Avoid unintentional starting. Don't carry hooked-up tool  
with finger on trigger.  
Repair servicing should be done only by an authorized  
service representative.  
Air tools can cause the workpiece to move upon con-  
tact leading to injury.  
Use clamps or other devices to prevent movement.  
Loss of control of the tool can lead to injury to self or  
others.  
Never operate tool while under the influence of drugs  
or alcohol.  
Don't overreach. Keep proper footing and balance at all  
times.  
Keep handles dry, clean, and free from oil and grease.  
Stay alert. Watch what you are doing. Use common  
sense. Do not operate tool when you are tired.  
Poor quality, improper, or damaged tools such as  
grinding wheels, chisels, sockets, drills, nailers,  
staplers, etc., can fly apart during operation, propelling  
particles throughout the work area causing serious  
injury.  
Always use tool attachments rated for the speed of the  
power tool.  
Never use tools which have been dropped, impacted or  
damaged by use.  
Use only impact grade sockets on an impact wrench.  
Do not apply excessive force to the tool, let the tool  
perform the work.  
Fasteners could ricochet or be propelled causing  
serious injury or property damage.  
Never point discharge of tool at self or others.  
Do not pull trigger unless tool contact safety device is  
against work surface.  
Never attempt to drive fasteners into hard surfaces  
such as steel, concrete, or tile.  
Take care to avoid driving a fastener on top of another  
fastener.  
Position tool carefully so that fasteners will be delivered  
to the proper location.  
Download from Www.Somanuals.c3o-mEN.GAll Manuals Search And Download.  
D22722  
HAZARD  
RISK OF INJURY (continued)  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Maintain the tool with care.  
Keep a cutting tool sharp and clean. A properly  
maintained tool, with sharp cutting edges reduces the  
risk of binding and is easier to control.  
Improperly maintained tools and accessories can cause  
serious injury.  
There is a risk of bursting if the tool is damaged.  
Check for misalignment or binding of moving parts,  
breakage of parts, and any other condition that affects  
the tool’s operation. If damaged, have the tool serviced  
before using.  
Use only accessories identified by the manufacturer to  
be used with specific tools.  
Use of an accessory not intended for use with the  
specific tools, increases the risk of injury to persons.  
HAZARD  
RISK OF ELETRIC SHOCK  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Using air tools to attach electrical wiring can result in  
electrocution or death.  
Never use nailer/staplers to attach electrical wiring  
while energized.  
This tool is not provided with an insulated gripping  
surface. Contact with a “live” wire will also make  
exposed metal parts of the tool “live” and can result in  
electrocution or death.  
Avoid body contact with grounded surfaces such as  
pipes, radiators, ranges, and refrigerators. There is an  
increased risk of electric shock if your body is  
grounded.  
Thoroughly investigate the workpiece for possible  
hidden wiring before performing work.  
Fasteners coming in contact with hidden electrical  
wiring could cause electrocution or death.  
HAZARD  
RISK OF ENTANGLEMENT  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Tools which contain moving elements, or drive other mov-  
ing tools, such as grinding wheels, sockets, sanding discs,  
etc. can become entangled in hair, clothing, jewelry and  
other loose objects, resulting in severe injury.  
Never wear loose fitting clothes, or apparel which  
contains loose straps or ties, etc. which could become  
entangled in moving parts of the tool.  
Remove any jewelry, watches, identifications, bracelets,  
necklaces, etc. which might become caught by the  
tool.  
Keep hands away from moving parts. Tie up or cover  
long hair.  
Always wear proper fitting clothing and other safety  
equipment when using this tool.  
HAZARD  
RISK OF CUT OR BURNS  
WHAT COULD HAPPEN  
HOW TO PREVENT IT  
Tools which cut, shear, drill, staple, punch, chisel, etc.  
are capable of causing serious injury.  
Keep the working part of the tool away from hands and  
body.  
Download from Www.Somanuals.c4o-mEN.GAll Manuals Search And Download.  
D22722  
SPECIFICATIONS  
Free Speed  
Maximum Working Pressure  
Air Inlet  
Recommended Hose Size  
Keyless Chuck  
600 RPM  
90 PSI  
1/4" NPT  
3/8" I.D.  
1/2”  
Air Consumption @ 90 PSI  
6.0 SCFM  
ASSEMBLY  
Accessories Required  
IMPORTANT: Line pressure or hose inside diameter should be increased to compensate  
for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D.  
and fittings should have 1/4” NPT thread.  
Assemble Stabilizer Handle  
1. Slide stabilizer handle onto tool, rotate to desired position and tighten.  
OPERATION  
Chuck  
Reverse  
and  
Forward  
Lever  
Stabilizer  
Handle  
Trigger  
Air Inlet  
Before each use:  
G
Drain water from air compressor tank and condensation from air lines. See air  
compressor’s operators manual.  
Disconnect the tool from the air supply before lubricating or  
changing drill bits.  
G
G
G
Lubricate tool, see “Maintenance” section in this manual.  
Open the keyless chuck (A), no tools are required.  
Insert and center drill bit in the jaws (B) as you close chuck.  
NOTE: An off centered drill bit will wobble and could break.  
Connect tool to air hose of recommended size. NOTE: The use  
G
of a quick connect set makes connecting easier.  
B
A
IMPORTANT: The use of air filters and air line lubricators is  
recommended.  
Download from Www.Somanuals.c5o-mEN.GAll Manuals Search And Download.  
D22722  
To use:  
G
Turn air compressor on and allow air tank to fill.  
G
Set the air compressor’s regulator to 90 PSI. This tool operates at a maximum 90  
PSI pressure.  
G
This tool has a stabilizer handle (C). Loosen stabilizer  
handle and rotate to desired position and tighten.  
G
G
Place the tool in reverse or forward position.  
Position drill bit at the point to be drilled and depress the  
C
trigger.  
G
G
G
Always disconnect air supply when changing drill bits.  
Release trigger to stop tool.  
When job is complete, turn the air compressor off  
Forward  
and store as described in the air compressor  
operator manual.  
Reverse  
Tips  
G
Locate the position of the hole to be drilled. Mark  
that position with a center punch. This provides a good seat for the drill bit point  
and keeps the drill from moving from the mark. Never apply a spinning drill bit to the  
work.  
G
G
Apply just enough pressure to keep the drill cutting. Do not force it. Too much  
pressure may cause the drill to break.  
Withdraw the drill several times to clear the cuttings when drilling deep holes.  
MAINTENANCE  
Lubrication  
Air tools require lubrication throughout the life of the tool. The air motor and bearing uses  
compressed air to power the tool. Because moisture in compressed air will rust the air  
motor, you must lubricate the motor daily. An inline oiler is recommended.  
To lubricate the air motor manually:  
G
Disconnect the tool from the air supply holding it so the air inlet  
faces up.  
G
Hold the trigger in and place one to two drops of air tool oil in the  
air inlet Depressing the trigger helps circulate oil in the motor.  
NOTE: Use SAE #10 weight oil if air tool oil is not available.  
G
Connect the tool to an air source, cover the exhaust end with a  
towel and run for a few seconds.  
Any excess oil in the motor is immediately  
expelled from the exhaust port. Always direct exhaust port  
away from people or objects.  
Failure to lubricate the tool at the air inlet will void your  
warranty.  
Download from Www.Somanuals.c6o-mEN.GAll Manuals Search And Download.  
D22722  
REPAIR PARTS  
38  
23  
37  
18  
28  
(5)  
33  
32A  
29  
26  
41  
32  
27  
33  
42  
30  
Ref  
No.  
18  
23  
26  
27  
28  
29  
30  
32  
32a  
33  
37  
38  
Part No.  
Description  
Rotor Blade  
Motor Gasket  
Trigger  
Spring  
O-Ring  
O-Ring  
Valve Bearing  
Bushing  
Valve Shaft  
O-Ring  
Spring Pin  
Hand Grip  
Handle  
Qty  
5
1
1
1
1
1
1
1
1
2
1
1
u
u
+
+
+
+
+
+
+
+
+
s
41  
s
1
42  
s
Handle Ring  
1
+
u
s
Only available in Trigger Repair Kit D25318  
Only available in Tune Up Kit D26762  
Only availabe in Service Kit D25328  
NOTE: Parts not listed are not serviceable.  
Download from Www.Somanuals.c7o-mEN.GAll Manuals Search And Download.  
D22722  
LIMITED WARRANTY  
PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are  
free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools,  
service parts, pressure washers, and generators, which have the following warranty periods:  
3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM.  
2 YEARS - Limited warranty on oil-lubricated air compressor pumps.  
1 YEAR - Limited warranty on all other air compressor components.  
2 YEARS - Limited warranty on electric generator alternators.  
1 YEAR - Limited warranty on other generator components.  
2 YEARS - Limited warranty on pneumatic air tools as described in Porter-Cable general catalog.  
1 YEAR - Limited warranty on pressure washers used in consumer applications (i.e. personal residential household  
usage only).  
90 DAY - Pressure washers used for commercial applications (income producing) and service parts.  
1 YEAR - Limited warranty on all accessories.  
Porter-Cable will repair or replace, at Porter-Cable's option, products or components which have failed within the  
warranty period. Service will be scheduled according to the normal work flow and business hours at the service  
center location, and the availability of replacement parts. All decisions of Porter-Cable Corporation with regard to this  
limited warranty shall be final.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
RESPONSIBILITY OF ORIGINAL PURCHASER (initial User):  
To process a warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by an  
Porter-Cable Authorized Warranty Service Center. For the location of the nearest Porter-Cable Authorized Warranty  
Service Center call 1-888-559-8550, 24 hours a day, 7 days a week.  
Retain original cash register sales receipt as proof of purchase for warranty work.  
Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s).  
Deliver or ship the product to the nearest Porter-Cable Authorized Warranty Service Center. Freight costs, if any, must  
be paid by the purchaser.  
Air compressors with 60 and 80 gallon tanks will be inspected at the site of installation. Contact the nearest Porter-  
Cable Authorized Warranty Service Center that provides on-site service calls, for service call arrangements.  
If the purchaser does not receive satisfactory results from the Porter-Cable Authorized Warranty Service Center, the  
purchaser should contact Porter-Cable.  
THIS WARRANTY DOES NOT COVER:  
Merchandise sold as reconditioned, used as rental equipment, and floor or display models.  
Merchandise that has become damaged or inoperative because of ordinary wear, misuse*, cold, heat, rain, excessive  
humidity, freeze damage, use of improper chemicals, negligence, accident, failure to operate the product in  
accordance with the instructions provided in the Owners Manual(s) supplied with the product, improper maintenance,  
the use of accessories or attachments not recommended by Porter-Cable, or unauthorized repair or alterations.  
*
An air compressor that pumps air more than 50% during a one hour period is considered misuse because the air  
compressor is undersized for the required air demand.  
Repair and transportation costs of merchandise determined not to be defective.  
Costs associated with assembly, required oil, adjustments or other installation and start-up costs.  
Expendable parts or accessories supplied with the product which are expected to become inoperative or unuseable  
after a reasonable period of use, including but not limited to sanding disks or pads, saw and shear blades, grinding  
stones, springs, chisels, nozzles, o-rings, air jets, washers and similar accessories.  
Merchandise sold by Porter-Cable which has been manufactured by and identified as the product of another  
company, such as gasoline engines. The product manufacturer's warranty, if any, will apply.  
ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM  
ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS NOT COVERED BY THIS WARRANTY. Some  
states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or  
exclusion may not apply to you.  
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. Some states do not allow  
limitations on how long an implied warranty lasts, so the above limitations may not apply to you.  
Porter-Cable Corporation  
Jackson, TN USA  
1-888-559-8550  
Download from Www.Somanuals.c8o-mEN.GAll Manuals Search And Download.  
D22722  

Peerless Industries TV Mount HLG452 002 User Manual
Pelco DVR DX4104 Series User Manual
Pelco Security Camera C3426M D 3 08 3 User Manual
Pelco TV Mount C293M B 1 09 User Manual
Philips Battery Charger R03B4A90 User Manual
Philips Home Theater System HTS3345 User Manual
Philips Surge Protector SPP2304WC User Manual
PHL Audio Portable Speaker B17 User Manual
Polar Heart Rate Monitor FT80 User Manual
Poulan Trimmer PPB32SST User Manual