Reference Manual for the
Model DG824M Wireless
ADSL Modem Gateway
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Phone 1-888-NETGEAR
SM-DG824MNA-0
November 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das DG824M Wireless ADSL Modem Gateway gemäß der im BMPT-AmtsblVfg 243/
1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B.
Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der
Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Certificate of the Manufacturer/Importer
It is hereby certified that the DG824M Wireless ADSL Modem Gateway has been suppressed in accordance with the
conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.
Customer Support
Refer to the Support Information Card that shipped with your DG824M Wireless ADSL Modem Gateway.
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL)
http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer
or Netscape are required.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface
About This Guide
Chapter 1
Introduction
802.11b Standards-based Wireless Networking ......................................................1-2
Protocol Support ......................................................................................................1-3
Easy Installation and Management ..........................................................................1-4
The Gateway’s Rear Panel ......................................................................................1-8
Chapter 2
Computer Hardware Requirements .........................................................................2-2
LAN Configuration Requirements ............................................................................2-2
Internet Configuration Requirements .......................................................................2-2
Where Do I Get the Internet Configuration Parameters? .........................................2-2
Connecting the DG824M Wireless ADSL Modem Gateway to Your LAN ......................2-5
Connecting the DG824M to the Internet .........................................................................2-9
Testing Your Internet Connection ..................................................................................2-16
Manually Configuring Your Internet Connection ...........................................................2-17
Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Wireless Configuration
Observe Placement and Range Guidelines .............................................................3-1
Wireless Settings ............................................................................................................3-2
Configuring Wired Equivalent Privacy (WEP) ..........................................................3-6
Chapter 4
Protecting Your Network
Configuring Basic Firewall Services ...............................................................................4-3
Considerations for Inbound Rules .....................................................................4-9
Outbound Rules (Service Blocking) .......................................................................4-10
Outbound Rule Example: Blocking Instant Messenger ...................................4-10
Order of Precedence for Rules ..............................................................................4-12
Chapter 5
Backing Up, Restoring, or Erasing Your Settings ...........................................................5-1
Upgrading the Gateway’s Firmware ...............................................................................5-3
Network Management Information .................................................................................5-5
Viewing Gateway Status and Usage Statistics .........................................................5-5
Viewing Attached Devices ........................................................................................5-9
Viewing, Selecting, and Saving Logged Information ..............................................5-10
Selecting What Information to Log ..................................................................5-11
Saving Log Files on a Server ..........................................................................5-12
Examples of log messages ....................................................................................5-12
vi
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Activation and Administration ..........................................................................5-12
Dropped Packets .............................................................................................5-12
Enabling Security Event E-mail Notification .................................................................5-13
Chapter 6
Advanced Configuration
Configuring Advanced Security ......................................................................................6-1
Setting Up A Default DMZ Server ............................................................................6-1
Respond to Ping on Internet WAN Port ...................................................................6-2
LAN TCP/IP Setup ...................................................................................................6-3
DHCP ................................................................................................................6-5
Reserved IP addresses .....................................................................................6-6
Configuring Dynamic DNS .......................................................................................6-7
Using Static Routes ........................................................................................................6-9
Chapter 7
Troubleshooting
Basic Functioning ...........................................................................................................7-1
Test LED Never Turns On or Test LED Stays On .....................................................7-2
Troubleshooting the Web Configuration Interface ..........................................................7-3
ADSL link .................................................................................................................7-4
Troubleshooting PPPoE or PPPoA ..........................................................................7-6
Troubleshooting Internet Browsing ..........................................................................7-6
Troubleshooting a TCP/IP Network Using the Ping Utility ..............................................7-7
Testing the LAN Path to Your Router .......................................................................7-7
Testing the Path from Your PC to a Remote Device ................................................7-8
Contents
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring the Default Configuration and Password ........................................................7-9
Appendix A
Technical Specifications
Appendix B
Network and Routing Basics
What is a Router? ................................................................................................... B-2
Netmask .................................................................................................................. B-4
IP Configuration by DHCP .................................................................................... B-10
Uplink Switches and Crossover Cables .................................................................B-11
Internet Security and Firewalls .................................................................................... B-12
Ad Hoc Mode (Peer-to-Peer Workgroup) ....................................................... B-14
Infrastructure Mode ........................................................................................ B-14
Extended Service Set Identification (ESSID) ........................................................ B-14
Authentication and WEP Encryption ..................................................................... B-15
Wireless Channel Selection .................................................................................. B-15
viii
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Preparing Your Network
Preparing Your Computers for TCP/IP Networking ....................................................... C-1
Configuring Windows 95, 98, and Me for TCP/IP Networking ....................................... C-2
Selecting Windows’ Internet Access Method .......................................................... C-6
Verifying TCP/IP Properties .................................................................................... C-6
Configuring Windows NT4, 2000 or XP for IP Networking ............................................ C-7
DHCP Configuration of TCP/IP in Windows XP ..................................................... C-8
MacOS 8.6 or 9.x .................................................................................................. C-16
Verifying the Readiness of Your Internet Account ....................................................... C-18
Are Login Protocols Used? ................................................................................... C-18
What Is Your Configuration Information? .............................................................. C-18
Obtaining ISP Configuration Information for Windows Computers ....................... C-19
Obtaining ISP Configuration Information for Macintosh Computers ..................... C-20
Restarting the Network ................................................................................................ C-21
Glossary
Index
Contents
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure 2-1: Record Your Internet Connection Information ......................................2-4
Procedure 2-2: Connecting the Gateway ......................................................................2-5
Procedure 2-8: Manual Configuration .........................................................................2-18
Procedure 3-1: Configuring Basic Wireless Network Settings .......................................3-3
Procedure 4-1: Changing the Built-In Password ...........................................................4-1
Procedure 4-1: Changing the Administrator Login Timeout ..........................................4-2
Procedure 4-2: Block Keywords and Sites ....................................................................4-3
Procedure 4-3: Define Services ..................................................................................4-13
Procedure 4-4: Setting Your Time Zone ......................................................................4-14
Procedure 4-5: Scheduling Firewall Services ..............................................................4-16
Procedure 5-6: Backup the Configuration to a File .......................................................5-1
Procedure 5-7: Restore a Configuration from a File ......................................................5-3
Procedure 5-8: Erase the Configuration ........................................................................5-3
Procedure 5-1: Gateway Upgrade .................................................................................5-4
Procedure 5-2: Configure Remote Management ........................................................5-16
Procedure 6-1: Configuring A Default DMZ Server. ......................................................6-2
Procedure 6-1: Configure LAN TCP/IP Setup ...............................................................6-6
Procedure 6-2: Configure Dynamic DNS ......................................................................6-8
Procedure 6-3: Configuring Static Routes ...................................................................6-10
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
About This Guide
Thank you for purchasing the NETGEAR™ DG824M Wireless ADSL Modem Gateway.
Audience
This reference manual assumes that the reader has basic to intermediate computer and Internet
skills. However, basic computer network, Internet, firewall, and wireless technologies tutorial
information is provided in the Appendices.
Technical Support
For help with any technical issues, contact Customer Support at 1-888-NETGEAR, or visit us on
the Web at www.NETGEAR.com. The NETGEAR Web site includes an extensive knowledge
base, answers to frequently asked questions, and a means for submitting technical questions
online.
We recommend you register your product online at: www.NETGEAR.com/register
About This Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Typographical Conventions
This guide uses the following typographical conventions:
italics
Book titles and UNIX file, command, and directory names.
Screen text, user-typed command-line entries.
Menu titles and window and button names.
courier font
Initial Caps
[Enter]
Named keys in text are shown enclosed in square brackets. The notation
[Enter] is used for the Enter key and the Return key.
[Ctrl]+C
Two or more keys that must be pressed simultaneously are shown in text
linked with a plus (+) sign.
ALL CAPS
DOS file and directory names.
Special Message Formats
This guide uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Procedure: This format is used to let you know that you are following a sequence of
steps required to complete a task.
Warning: This format is used to highlight information about the possibility of injury or
equipment damage.
Danger: This format is used to alert you that there is the potential for incurring an
electrical shock if you mishandle the equipment.
4
About This Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter describes the features of the NETGEAR DG824M Wireless ADSL Modem Gateway.
firewall which enables your entire network to safely share an Internet connection that otherwise is
used by a single PC.
Note: If you are unfamiliar with networking and routing, refer to Appendix B, “Network
and Routing Basics,” to become more familiar with the terms and procedures used in this
manual.
About the Gateway
The DG824M Wireless ADSL Modem Gateway provides continuous, high-speed 11 Mbps access
between your wireless and Ethernet devices. The DG824M gateway enables your entire network
to share an Internet connection through the built-in ADSL modem that otherwise is used by a
single PC. With minimum setup, you can install and use the gateway within minutes.
The DG824M gateway provides multiple Web content filtering options, plus e-mail browsing
activity reporting and instant alerts. Parents and network administrators can establish restricted
access policies based on time-of-day, website addresses and address keywords, and share
high-speed ADSL Internet access for up to 253 personal computers. The included firewall and
Network Address Translation (NAT) features protect you from hackers.
Key Features
The DG824M gateway provides the following features:
•
A Powerful, True Firewall
Introduction
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
•
•
•
•
802.11b Standards-based wireless networking
Content Filtering
Auto Sensing and Auto Uplink™ LAN Ethernet Connections
Extensive Internet Protocol Support
Easy, web-based setup for installation and management
A built-in ADSL modem
These features are discussed below.
802.11b Standards-based Wireless Networking
The DG824M gateway includes an 802.11b-compliant wireless access point, providing
continuous, high-speed 11 Mbps access between your wireless and Ethernet devices. The access
point provides:
•
•
•
•
802.11b Standards-based wireless networking at up to 11 Mbps
64-bit and 128-bit WEP encryption security
WEP keys can be generated manually or by passphrase
Wireless access can be restricted by MAC address.
A Powerful, True Firewall
Unlike simple Internet sharing NAT routers, the DG824M is a true firewall, using stateful packet
inspection to defend against hacker attacks. Its firewall features include:
•
Denial of Service (DoS) protection
Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death,
SYN Flood, LAND Attack and IP Spoofing.
•
•
•
Blocks unwanted traffic from the Internet to your LAN.
Blocks access from your LAN to Internet locations or services that you specify as off-limits.
Logs security incidents
The DG824M will log security events such as blocked incoming traffic, port scans, attacks,
and administrator logins. You can configure the gateway to email the log to you at specified
intervals. You can also configure the gateway to send immediate alert messages to your email
address or email pager whenever a significant event occurs.
1-2
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Content Filtering
With its content filtering feature, the DG824M prevents objectionable content from reaching your
PCs. The gateway allows you to control access to Internet content by screening for keywords
within Web addresses. You can configure the gateway to log and report attempts to access
objectionable Internet sites.
Auto Sensing and Auto Uplink™ LAN Ethernet Connections
With its internal 4-port 10/100 switch, the DG824M can connect to either a 10 Mbps standard
Ethernet network or a 100 Mbps Fast Ethernet network. The local LAN ports are autosensing and
capable of full-duplex or half-duplex operation.
The gateway incorporates Auto UplinkTM technology. Each LOCAL Ethernet port will
automatically sense whether the Ethernet cable plugged into the port should have a ‘normal’
connection such as to a PC or an ‘uplink’ connection such as to a switch or hub. That port will then
configure itself to the correct configuration. This feature also eliminates the need to worry about
crossover cables, as Auto Uplink will accommodate either type of cable to make the right
connection.
Protocol Support
The DG824M supports the Transmission Control Protocol/Internet Protocol (TCP/IP) and Routing
Information Protocol (RIP). Appendix B, “Network and Routing Basics” provides further
information on TCP/IP.
•
IP Address Sharing by NAT
The DG824M allows several networked PCs to share an Internet account using only a single
IP address, which may be statically or dynamically assigned by your Internet service provider
(ISP). This technique, known as Network Address Translation (NAT), allows the use of an
inexpensive single-user ISP account.
•
Automatic Configuration of Attached PCs by DHCP
The DG824M dynamically assigns network configuration information, including IP, gateway,
and domain name server (DNS) addresses, to attached PCs on the LAN using the Dynamic
Host Configuration Protocol (DHCP). This feature greatly simplifies configuration of PCs on
your local network.
Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
DNS Proxy
When DHCP is enabled and no DNS addresses are specified, the gateway provides its own
address as a DNS server to the attached PCs. The gateway obtains actual DNS addresses from
the ISP during connection setup and forwards DNS requests from the LAN.
•
PPP over Ethernet (PPPoE)
PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an ADSL
connection by simulating a dial-up connection. This feature eliminates the need to run a login
program such as EnterNet or WinPOET on your PC.
•
•
PPP over ATM (PPPoA)
PPP over ATM is a protocol for connecting remote hosts to the Internet over an ADSL
connection by simulating a ATM connection.
Dynamic DNS
Dynamic DNS services allow remote users to find your network using a domain name when
your IP address is not permanently assigned. The gateway contains a client that can connect to
many popular Dynamic DNS services to register your dynamic IP address.
Easy Installation and Management
You can install, configure, and operate the DG824M within minutes after connecting it to the
network. The following features simplify installation and management tasks:
•
Browser-based management
Browser-based configuration allows you to easily configure your gateway from almost any
type of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup
Wizard is provided and online help documentation is built into the browser-based Web
Management Interface.
•
•
Smart Wizard
The gateway automatically senses the type of Internet connection, asking you only for the
information required for your type of ISP account.
Remote management
The gateway allows you to login to the Web Management Interface from a remote location via
the Internet. For security, you can limit remote management access to a specified remote IP
address or range of addresses, and you can choose a nonstandard port number.
1-4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
Diagnostic functions
The gateway incorporates built-in diagnostic functions such as Ping, DNS lookup, and remote
reboot. These functions allow you to test Internet connectivity and reboot the gateway. You
can use these diagnostic functions directly from the DG824M when your are connect on the
LAN or when you are connected over the Internet via the remote management function.
•
•
Visual monitoring
The gateway’s front panel LEDs provide an easy way to monitor its status and activity.
Flash EPROM for firmware upgrade
Introduction
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
What’s in the Box?
The product package should contain the following items:
•
•
•
•
•
•
DG824M Wireless ADSL Modem Gateway
AC power adapter (varies by region)
Category 5 (Cat 5) Ethernet cable
Telephone cable
Microfilters (quantity and type vary by region)
Model DG824M Resource CD, including:
— This guide
— Application Notes
•
•
A Quick Printed Installation Guide
Warranty and Support Information Cards
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
The Gateway’s Front Panel
The DG824M Wireless ADSL Modem Gateway front panel shown below contains status LEDs.
Figure 1-1: DG824M Front Panel
1-6
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
You can use the LEDs to verify various conditions. Table 1-1 lists and describes each LED on the
front panel of the router. These LEDs are green when lit.
Table 1-1.
LED Descriptions
Label
Activity
Description
Power
On
Off
Power is supplied to the router.
Power is not supplied to the router.
Test
On
Off
The system is initializing.
The system is ready and running.
Internet
Wireless
LAN
Blink -- Amber
On -- Green
Blink -- Green
Indicates ADSL training.
The Internet port has detected a link with an attached device.
Data is being transmitted or received by the Internet port.
On
Indicates that the Wireless port is initialized.
On (Green)
Blink (Green)
On (Amber)
Blink (Amber)
Off
The Local port has detected link with a 100 Mbps device.
Data is being transmitted or received at 100 Mbps.
The Local port has detected link with a 10 Mbps device.
Data is being transmitted or received at 10 Mbps.
No link is detected on this port.
Introduction
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The Gateway’s Rear Panel
The rear panel of the DG824M Wireless ADSL Modem Gateway (Figure 1-2) contains port
connections.
Figure 1-2: DG824M Rear Panel
Viewed from left to right, the rear panel contains the following elements:
•
•
•
•
•
AC power adapter outlet
Factory Default Reset push button
Wireless antenna
Four Local Ethernet RJ-45 ports for connecting the gateway to the local computers
ADSL port for connecting the gateway to an ADSL line
1-8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Connecting the Gateway to the Internet
This chapter describes how to set up the gateway on your Local Area Network (LAN), connect to
the Internet, how to configure your DG824M Wireless ADSL Modem Gateway for Internet access
using the Setup Wizard, or how to manually configure your Internet connection.
What You Will Need Before You Begin
You need to prepare these three things before you can establish an Internet connection through
your gateway:
1. The gateway connected to an ADSL line and a computer properly connected to the gateway as
explained below.
2. Active Internet service such as that provided by an ADSL account.
3. The Internet Service Provider (ISP) configuration information for your DSL account.
Cabling Requirements
The built-in ADSL modem of the DG824M gateway connects to the Internet via your telephone
line using standard twisted-pair telephone cables.
Note: Do not connect the DG824M to the ADSL line through a microfilter unless the microfilter
is specifically designed for this purpose. Doing so will prevent the built-in DSL modem in the
DG824M from establishing a connection to the Internet. If you have any doubts about this, it is
recommended that you connect the DG824 directly to the ADSL line.
The DG824M gateway connects to your LAN via twisted-pair Ethernet cables.
Connecting the Gateway to the Internet
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Computer Hardware Requirements
To use the DG824M gateway on your network, each computer must have an installed Ethernet
Network Interface Card (NIC) and an Ethernet cable, or a 802.11b wireless adapter. If the
computer will connect to your network at 100 Mbps, you must use a Category 5 (CAT5) cable such
as the one provided with your gateway.
LAN Configuration Requirements
For the initial connection to the Internet and configuration of your gateway, you will need to
connect a computer to the gateway which is set to automatically get its TCP/IP configuration from
the gateway via DHCP.
Note: Please refer to Appendix C, “Preparing Your Network for assistance with DHCP
configuration.
Internet Configuration Requirements
Depending on how your ISP set up your Internet account, you will need one or more of these
configuration parameters to connect your gateway to the Internet:
•
•
•
•
•
•
VPI/VCI parameters
Multiplexing Method
Host and Domain Names
ISP Login Name and Password
ISP Domain Name Server (DNS) Addresses
Fixed or Static IP Address
Where Do I Get the Internet Configuration Parameters?
There are several ways you can gather the required Internet connection information.
•
Your ISP should have provided you with all the information needed to connect to the Internet.
If you cannot locate this information, you can ask your ISP to provide it or you can try one of
the options below.
•
If you have a computer already connected using the active Internet access account, you can
gather the configuration information from that computer.
2-2
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
•
For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the
Ethernet adapter, and click Properties.
For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry
for the Ethernet adapter, and click Properties.
For Macintosh computers, open the TCP/IP or Network control panel.
•
You may also refer to the DG824M Resource CD for the NETGEAR Router ISP Guide which
provides Internet connection information for many ISPs.
Once you locate your Internet configuration parameters, you may want to record them on the page
below according to the instructions in “Record Your Internet Connection Information” on page
2-4.
Connecting the Gateway to the Internet
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 2-1: Record Your Internet Connection Information
Print this page. Fill in the configuration parameters from your Internet Service Provider (ISP).
ISP Multiplexing Method and Virtual Circuit Number: The default settings of your DG824M
Wireless ADSL Modem Gateway will work fine for most ISPs. However, some ISPs use a specific
Multiplexing Method or a Virtual Circuit Number for either the VPI or VCI. If your ISP provided
you with a specific Multiplexing Method or VPI/VCI number, then fill in the following:
Multiplexing Method, circle one: LLC-based or VC-based
VPI: ________ A number between 0 and 255. VCI: ___________ A number between 1and 65535.
ISP Login Name: The login name and password are case sensitive and must be entered exactly as
given by your ISP. Some ISPs use your full e-mail address as the login name. The Service Name is
not required by all ISPs. If you connect using a login name and password, then fill in the
following:
Login Name: ______________________________ Password: ____________________________
Service Name: _____________________________
Fixed or Static IP Address: If you have a static IP address, record the following information. For
example, 169.254.141.148 could be a valid IP address.
Fixed or Static Internet IP Address: ______ . ______ . ______ . ______
Gateway IP Address: ______ . ______ . ______ . ______
Subnet Mask: ______ . ______ . ______ . ______
ISP DNS Server Addresses: If you were given DNS server addresses, fill in the following:
Primary DNS Server IP Address: ______ . ______ . ______ . ______
Secondary DNS Server IP Address: ______ . ______ . ______ . ______
Host and Domain Names: Some ISPs use a specific host or domain name like CCA7324-A or
home. If you haven’t been given host or domain names, you can use the following examples as a
guide:
•
Your ISP might call this your account, user, host, computer, or system name.
•
If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.
ISP Host Name: _________________________ ISP Domain Name: _______________________
2-4
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Connecting the DG824M Wireless ADSL Modem Gateway to
Your LAN
This section provides instructions for connecting the DG824M gateway.
Note: The Resource CD included with your gateway contains an animated Installation Assistant to
help you through this procedure.
Procedure 2-2: Connecting the Gateway
There are three steps to connecting your firewall:
1. Connect the gateway to your ADSL line
1. Connect the gateway to the computers on your network
2. Log in to the gateway
3. Connect to the Internet
Follow the steps below to connect your gateway to your network. You can also refer to the
Resource CD included with your gateway which contains an animated Installation Assistant to
help you through this procedure.
Connecting the Gateway to the Internet
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
1. Connect the DG824M.
a. Turn off your computer.
b. Connect the cable (A) from the DG824M ADSL port to your ADSL outlet, being sure to
properly connect the wires as shown in the illustration below.
Line
A
Wireless ADSL Modem Gateway DG824M
Figure 2-1: Connect the ADSL Cable
Note: The illustration above depicts a microfilter splitter specifically designed to enable a
phone and ADSL modem to connect to the same phone line wall jack outlet. Do not connect
the DG824B to your ADSL line with a microfilter unless the microfilter specifically designed
for that purpose. Doing so will prevent the modem from establishing a connection to the
Internet. If you have any doubts about this, use only a phone cord to connect the DG824B to
the ADSL wall jack outlet.
2-6
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
c. Connect the Ethernet cable (B) from your DG824M’s LAN port to a computer.
Line
B
Wireless ADSL Modem Gateway DG824M
Figure 2-2: Connect the gateway to a computer
Note: The DG824M gateway incorporates Auto UplinkTM technology. Each Ethernet LAN
port will automatically sense whether the cable plugged into the port should have a
'normal' connection (e.g. connecting to a PC) or an 'uplink' connection (e.g. connecting to
a switch or hub). That port will then configure itself to the correct configuration. This
feature also eliminates the need to worry about crossover cables, as Auto Uplink will
accommodate either type of cable to make the right connection.
d. Connect the power adapter to the gateway and plug it in to a power outlet. Verify the
following:
The power light is lit after turning on the gateway.
The ADSL link light is solid green, indicating a link has been established to the
cable network.
e. Now, turn on your computer. If software usually logs you in to your Internet connection,
do not run that software or cancel it if it starts automatically.
The local lights are lit for any connected computers.
Connecting the Gateway to the Internet
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Note: For instructions on connecting computers to the DG824M via wireless links, please
see the Chapter 3, “Wireless Configuration”.
2. Log in to the DG824M.
Note: If you usually run software to log in to your Internet connection, do not run that
software.
a. Connect to the gateway by typing http://192.168.0.1 in the address field of Internet
Explorer or Netscape® Navigator.
Figure 2-3: Log in to the gateway
A login window opens as shown below:
Figure 2-4: Login window
b. For security reasons, the gateway has its own user name and password. When prompted,
enter admin for the gateway User Name and password for the gateway Password, both in
lower case letters.
Note: The user name and password are not the same as any user name or password you
may use to log in to your Internet connection.
2-8
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
3. Connect to the Internet.
Figure 2-5: Setup Wizard
Wizard link on the upper left of the main menu. Click the Yes button in the Setup Wizard.
b. Please click Next to follow the steps in the Setup Wizard to input the configuration
parameters from your ISP to connect to the Internet.
Note: If you were unable to connect to the gateway, please refer to troubleshooting procedures in
“Basic Functioning” on page 7-1.
4. Connect an ADSL microfilter to your phone.
a. ADSL transmissions use your phone wires and can interfere with the quality of your
phone service. A microfilter eliminates such problems. Depending on the country of
purchase, a microfilter may be included in your DG824M package. Locate a suitable
microfilter.
b. Connect the microfilter to your phone line between the phone set and the phone line wall
outlet. Each phone set requires a microfilter.
Note: Improperly connecting a microfilter to your DG824M gateway will block your
ADSL connection.
Connecting the DG824M to the Internet
The gateway is now properly attached to your network. You are now ready to configure your
gateway to connect to the Internet. There are two ways you can configure your gateway to connect
to the Internet:
Connecting the Gateway to the Internet
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
Manually choose which type of Internet connection you have and configure it.
These options are described below. In either case, unless your ISP automatically assigns your
configuration automatically via DHCP, you will need the configuration parameters from your ISP
you recorded in “Record Your Internet Connection Information” on page 2-4.
Procedure 2-3: Auto-Detecting Your Internet Connection Type
automatically determine your network connection type.
1. If your gateway has not yet been configured, the Setup Wizard shown in Figure 2-6 should
launch automatically.
Note: If, instead of the Setup Wizard menu, the main menu of the gateway’s Configuration
Manager as shown in Figure 2-11 appears, click the Setup Wizard link in the upper left to
bring up this menu.
When the Wizard launches, select Yes in the menu below to allow the gateway to
automatically determine your connection.
Figure 2-6: Built-in Web-based Configuration Manager Setup Wizard
2. Click Next
The Setup Wizard will now check for the following connection types:
•
•
Dynamic IP assignment
A login protocol such as PPPoE or PPPoA
2-10
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
Fixed IP address assignment
Next, the Setup Wizard will report which connection type it has discovered, and then display
the appropriate configuration menu. If the Setup Wizard finds no connection, you will be
prompted to check the physical connection between your gateway and the ADSL line. When
the connection is properly made, the gateway’s Internet LED should be on.
The procedures for filling in the configuration menu for each type of connection follow below.
Procedure 2-4: Wizard-Detected PPPoE Login Account Setup
If the Setup Wizard determines that your Internet service account uses a login protocol such as
PPP over Ethernet (PPPoE), you will be directed to a menu like the PPPoE menu in Figure 2-7:
Figure 2-7: Setup Wizard menu for PPPoE login accounts
1. Enter the PPPoE login user name, password, and Service Name (if required) as provided by
your ISP. These fields are case sensitive.
2. If you wish to change the login timeout, enter a new value in minutes. This determines how
long the gateway keeps the Internet connection active after there is no Internet activity from
the LAN. Entering a timeout value of zero means never log out.
Connecting the Gateway to the Internet
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your gateway will automatically log you
in.
3. Domain Name Server (DNS) Address: If you know that your ISP does not automatically
transmit DNS addresses to the gateway during login, select “Use these DNS servers” and enter
the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
If you enter an address here, after you finish configuring the gateway, reboot your PCs so
that the settings take effect.
4. Click on Apply to save your settings.
5. Click on the Test button to test your Internet connection. If the NETGEAR website does not
appear within one minute, refer to Chapter 7, “Troubleshooting”.
Procedure 2-5: Wizard-Detected PPPoA Login Account Setup
If the Setup Wizard determines that your Internet service account uses a login protocol such as
PPP over ATM (PPPoA), you will be directed to a menu like the PPPoA menu in Figure 2-7:
Figure 2-8: Setup Wizard menu for PPPoA login accounts
2-12
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
1. Enter your Login and Password. These fields are case sensitive. If you wish to change the
login timeout, enter a new value in minutes. This determines how long the gateway keeps the
Internet connection active after there is no Internet activity from the LAN. Entering a timeout
value of zero means never log out.
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your gateway will automatically log you
in.
2. Domain Name Server (DNS) Address:
These parameters may be necessary to access your ISP’s services such as mail or news servers.
If you leave the Domain Name field blank, the gateway will attempt to learn the domain
automatically from the ISP. If this is not successful, you may need to enter it manually.
If you know that your ISP does not automatically transmit DNS addresses to the gateway
during login, select “Use these DNS servers” and enter the IP address of your ISP’s Primary
DNS Server. If a Secondary DNS Server address is available, enter it also.
If you enter an address here, after you finish configuring the gateway, reboot your PCs so
that the settings take effect.
3. Click on Apply to save your settings.
4. Click on the Test button to test your Internet connection. If the NETGEAR website does not
appear within one minute, refer to Chapter 7, “Troubleshooting”.
Connecting the Gateway to the Internet
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 2-6: Wizard-Detected Dynamic IP Account Setup
If the Setup Wizard determines that your Internet service account uses Dynamic IP assignment,
you will be directed to the menu shown in Figure 2-9 below:
Figure 2-9: Setup Wizard menu for Dynamic IP address
1. Enter your Account Name (may also be called Host Name) and Domain Name. These
parameters may be necessary to access your ISP’s services such as mail or news servers. If you
leave the Domain Name field blank, the gateway will attempt to learn the domain
automatically from the ISP. If this is not successful, you may need to enter it manually.
2. If you know that your ISP does not automatically transmit DNS addresses to the gateway
during login, select “Use these DNS servers” and enter the IP address of your ISP’s Primary
DNS Server. If a Secondary DNS Server address is available, enter it also.
A DNS server is a host on the Internet that translates Internet names (such as
www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of
one or two DNS servers to your gateway during login. If the ISP does not transfer an
address, you must obtain it from the ISP and enter it manually here. If you enter an address
here, you should reboot your PCs after configuring the gateway.
3. The Router’s MAC Address is the Ethernet MAC address that will be used by the gateway on
the Internet port.
2-14
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
If your ISP allows access from only one specific computer’s Ethernet MAC address, select
“Use this MAC address.” The gateway will then capture and use the MAC address of the
computer that you are now using. You must be using the one computer that is allowed by the
ISP. Otherwise, you can type in a MAC address.
Note: Some ISPs will register the Ethernet MAC address of the network interface card in
MAC address of that PC. This feature allows your gateway to masquerade as that PC by
using its MAC address.
4. Click on Apply to save your settings.
5. Click on the Test button to test your Internet connection. If the NETGEAR website does not
appear within one minute, refer to Chapter 7, “Troubleshooting””.
Procedure 2-7: Wizard-Detected Fixed IP (Static) Account Setup
If the Setup Wizard determines that your Internet service account uses Fixed IP assignment, you
will be directed to the menu shown in Figure 2-10 below:
1. Enter your assigned IP Address, Subnet Mask, and the IP Address of your ISP’s gateway
router. This information should have been provided to you by your ISP. You will need the
configuration parameters from your ISP you recorded in “Record Your Internet Connection
Information” on page<$chapnum>4.
Connecting the Gateway to the Internet
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. Enter the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is
available, enter it also.
A DNS servers are required to perform the function of translating an Internet name such as
obtain DNS server addresses from your ISP and enter them manually here. You should
reboot your PCs after configuring the gateway for these settings to take effect.
3. Click on Apply to save the settings.
4. Click on the Test button to test your Internet connection. If the NETGEAR website does not
appear within one minute, refer to Chapter 7, “Troubleshooting”.
Testing Your Internet Connection
After completing the Internet connection configuration, your can test your Internet connection.
Log in to the gateway, then, from the Setup Basic Settings link, click on the Test button. If the
NETGEAR website does not appear within one minute, refer to Chapter 7, “Troubleshooting”.
Your gateway is now configured to provide Internet access for your network. Your gateway
automatically connects to the Internet when one of your computers requires access. It is not
necessary to run a dialer or login application such as Dial-Up Networking or Enternet to connect,
log in, or disconnect. These functions are performed by the gateway as needed.
To access the Internet from any computer connected to your gateway, launch a browser such as
Microsoft Internet Explorer or Netscape Navigator. You should see the gateway’s Internet LED
blink, indicating communication to the ISP. The browser should begin to display a Web page.
The following chapters describe how to configure the Advanced features of your gateway, and
how to troubleshoot problems that may occur.
2-16
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Manually Configuring Your Internet Connection
You can manually configure your gateway using the menu below, or you can allow the Setup
Wizard to determine your configuration as described in the previous section.
Figure 2-11: Browser-based configuration Basic Settings menu
Connecting the Gateway to the Internet
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 2-8: Manual Configuration
You can manually configure the gateway in the Basic Settings menu shown in Figure 2-11 using
these steps:
1. If your ISP ADSL service requires setting the Multiplexing Method and VPI/VCI parameters,
click on the ADSL Settings link from the main menu, fill in the settings your ISP provided,
and click Apply. Usually the default settings will work fine and you can skip this step.
2. Click the Basic Settings link on the Setup menu. If your Internet connection does not require a
login, fill in the settings according to the instructions below. If your Internet connection does
require a login, click Yes, and skip to step 3.
Select Yes if you normally must launch a login program such as Enternet or WinPOET in order
to access the Internet.
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your gateway will automatically log you
in.
a. Enter your Account Name (may also be called Host Name) and Domain Name.
These parameters may be necessary to access your ISP’s services such as mail or news
servers. These fields are case sensitive.
b. If you wish to change the login timeout, enter a new value in minutes. This determines
how long the gateway keeps the Internet connection active after there is no Internet
activity from the LAN. Entering an Idle Timeout value of zero means never log out.
c. Domain Name Server (DNS) Address:
If you know that your ISP does not automatically transmit DNS addresses to the gateway
during login, select “Use these DNS servers” and enter the IP address of your ISP’s
Primary DNS Server. If a Secondary DNS Server address is available, enter it also
3. If your Internet connection does require a login, click Yes at the top of the Basic Settings menu
and fill in the settings according to the instructions below.
a. Enter your Account Name (may also be called Host Name) and Domain Name.
These parameters may be necessary to access your ISP’s services such as mail or news
servers.
2-18
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
b. Internet IP Address:
If your ISP has assigned you a permanent, fixed (static) IP address for your PC, select
“Use static IP address”. Enter the IP address that your ISP assigned. Also enter the
netmask and the Gateway IP address. The Gateway is the ISP’s router to which your
gateway will connect.
c. Domain Name Server (DNS) Address:
If you know that your ISP does not automatically transmit DNS addresses to the gateway
during login, select “Use these DNS servers” and enter the IP address of your ISP’s
Primary DNS Server. If a Secondary DNS Server address is available, enter it also.
A DNS server is a host on the Internet that translates Internet names (such as
www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of
one or two DNS servers to your gateway during login. If the ISP does not transfer an
address, you must obtain it from the ISP and enter it manually here. If you enter an address
here, you should reboot your PCs after configuring the gateway.
d. Gateway’s MAC Address:
This section determines the Ethernet MAC address that will be used by the gateway on the
Internet port. Some ISPs will register the Ethernet MAC address of the network interface
card in your PC when your account is first opened. They will then only accept traffic from
the MAC address of that PC. This feature allows your gateway to masquerade as that PC
by “cloning” its MAC address.
To change the MAC address, select “Use this Computer’s MAC address.” The gateway
it.
4. Click Apply to save your settings.
5. Click on the Test button to test your Internet connection.
If the NETGEAR website does not appear within one minute, refer to Chapter 7,
“Troubleshooting”.
Connecting the Gateway to the Internet
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2-20
Connecting the Gateway to the Internet
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Wireless Configuration
This chapter describes how to configure the wireless features of your DG824M Wireless ADSL
Modem Gateway.
In planning your wireless network, you should consider the level of security required. You should
also select the physical placement of your gateway in order to maximize the network speed. For
further information on wireless networking, refer to “Wireless Networking” in Appendix B,
“Network and Routing Basics.”
Implement Appropriate Security
Unlike wired network data, your wireless data transmissions can extend beyond your walls and
can be received by anyone with a compatible adapter. For this reason, use the security features of
your wireless equipment. As a minimum precaution, change the SSID setting of all devices on
your network from the factory setting to a unique password. Restricting access by MAC address
filtering adds another obstacle against unwanted hosts joining your network. To hinder a
determined eavesdropper, you should enable Wired Equivalent Privacy (WEP) data encryption.
However, there may be a significant degradation of the data throughput on the wireless link when
WEP is enabled.
Observe Placement and Range Guidelines
The operating distance or range of your wireless connection can vary significantly based on the
physical placement of the wireless gateway.
Wireless Configuration
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Note: Failure to follow these guidelines can result in significant performance
degradation or inability to wirelessly connect to the router.
For best results, place your gateway:
•
•
•
Near the center of the area in which your PCs will operate.
In an elevated location such as a high shelf.
Away from potential sources of interference, such as PCs, microwaves, and 2.4 GHz cordless
phones.
•
Away from large metal surfaces.
Wireless Settings
To configure the Wireless interface of your gateway, click the Wireless link in the main menu of
the browser interface. The Wireless Settings menu will appear, as shown below:
Figure 3-1: Wireless Settings menu
In the Wireless Network section are the following parameters:
3-2
Wireless Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
Identification.
— Regulatory Domain. This field displays the region of operation for which the wireless
interface is intended. It may not be legal to operate the gateway in a region other than the
region shown here.
— Station Name. The gateway model number.
— SSID (Service Set ID). This is also known as the wireless network name. Enter a value of
up to 32 alphanumeric characters. The same SSID must be assigned to all wireless devices
in your network. The default SSID is Wireless.
•
•
Options.
— Channel No. This field determines which operating frequency will be used. It should not
be necessary to change the wireless channel unless you notice interference problems with
another nearby access point.
— WEP Status. Identifies the WEP options configured.
Access Point.
— All wireless stations. Any wireless station can connect.
— Trusted PCs only. Only PCs with MAC address which you have specified can connect.
Procedure 3-1: Configuring Basic Wireless Network Settings
1. Choose an SSID for the gateway and all wireless PCs
Devices on an 802.11b wireless network all share the same network name, or Service Set
Identificatier (SSID). The first step in configuring your wireless network is to choose a secure
value for your wireless network’s SSID. In the SSID box, enter a value of up to 32
alphanumeric characters. This same SSID must be entered in the configuration of all PCs and
devices connecting to this wireless network. The default SSID is Wireless.
Note: The SSID of any wireless access adapters must match the SSID you configure in
the DG824M Wireless ADSL Modem Gateway. If they do not match, you will not get a
wireless connection to the DG824M.
2. Set the Region of operation.
Select the geopgraphic region in which the wireless interface will operate. This setting
determines what radio frequencies will be available. It may not be legal to operate the gateway
in a region other than the region shown here.
Wireless Configuration
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
3. Set the Channel.
This field determines which operating frequency will be used. It should not be necessary to
change the wireless channel unless you notice interference problems with another nearby
wireless router or access point. Select a channel that is not being used by any other wireless
networks within several hundred feet of your gateway. The default channel is 6.
4. For initial configuration and test, make sure that the Wireless Card Access List is set to
Everyone and that Encryption Strength is set to Disabled.
Note: These settings are not recommended for normal operation, but should be set initially to
test basic wireless connectivity.
5. Click Apply to save your changes.
Note: If you are configuring the gateway from a wireless PC and you change the
gateway’s SSID, channel, or WEP settings, you will lose your wireless connection when
you click on Apply. You must then change the wireless settings of your PC to match the
gateway’s new settings.
6. Configure and test your PCs for wireless connectivity.
Program the wireless adapter of your PCs to have the same SSID and channel that you
configured in the router. Check that they have a wireless link and are able to obtain an IP
address by DHCP from the gateway.
Once your PCs have basic wireless connectivity to the gateway, then you can configre the
advanced wireless security functions of the gateway.
Using the Wireless Access by MAC Address Feature
By default, any wireless PC that is configured with the correct SSID will be allowed access to your
network. For increased security, you can restrict access to the wireless network to only allow
specific PCs based on their MAC addresses. You can allow access by:
The Trusted PCs window displays a list of MAC addresses that will be allowed to connect to the
gateway. These PCs must also be configured with SSID and WEP settings which match those of
the DG824M.
3-4
Wireless Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 3-2: Restricting Wireless Access by MAC Address
To restrict access based on MAC addresses, follow these steps:
1. From the Wireless Settings menu, click the Trusted PCs button to display the Wireless Access
menu, shown below:
Figure 3-2.
Wireless Access menu
2. Click the Add button.
3. Enter the MAC address of the authorized PC. The MAC address is usually printed on the
wireless card, or it may appear in the gateway’s DHCP table.
You can copy and paste the MAC addresses from the gateway’s Attached Devices menu into
the MAC Address box of this menu. To do this, configure each wireless PC to obtain a
wireless link to the gateway. The PC should then appear in the Attached Devices menu.
Note: If you are configuring the gateway from a wireless PC whose MAC address is not
in the Trusted PC list, and you select Trusted PCs only, you will lose your wireless
connection when you click on Apply. You must then access the gateway from a wired
PC to make any further changes.
4. Click Add to save your entry.
5. Return to the Wireless Settings menu, select Trusted PCs only, then click Apply.
To delete a MAC address from the table, click on it to select it, then click the Delete button.
To edit a MAC address from the table, click on it to select it, then click the Edit or Delete button.
Wireless Configuration
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Configuring Wired Equivalent Privacy (WEP)
Figure 3-3.
Wireless WEP menu
In the Wireless Settings menu you can configure WEP data encryption using the following
parameters:
•
Authentication Type
Normally this can be left at the default value of Automatic. If that fails, select the appropriate
value - Open System or Shared Key. Check your wireless card's documentation to see what
method to use.
•
Encryption Strength
The previous settings have determined which PCs will be allowed to access your wireless
network, but have not added any protection from eavesdropping. With this setting, you can
choose to have your data encrypted between the PCs and the gateway. Your choices are:
— Disable
No encryption will be applied. This setting is useful for troubleshooting your wireless
connection, but leaves your wireless data fully exposed.
— 64 or 128 bit WEP
Wireless Equivalent Privacy encryption will be applied. WEP provides some degree of
privacy, but can be defeated without great difficulty.
— Keys
If WEP is enabled, you can manually or automatically program the four data encryption
keys. These values must be identical on all PCs and Access Points in your network.
3-6
Wireless Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
Automatic - Enter a word or group of printable characters in the Passphrase box and
click the Generate button. The keys will be automatically populated with key values.
For 64-bit encryption, all four keys are generated from a single passphrase. With
128-bit encryption, each key can be generated with a different pasphrase.
Manual - Enter ten hexadecimal digits (any combination of 0-9, a-f, or A-F)
Select which of the four keys will be active.
Be sure to click Apply to save your settings in this menu.
Configuring WEP (Wired Equivalent Privacy)
If you have chosen to use WEP instead of IPSec, go to the Wireless Settings menu, click the
Encryption Strength box and select either 64 Bit WEP or 128 Bit WEP. The Wireless Settings
menu will display WEP setting fields, as shown below.
Figure 3-4.
Wireless Settings menu, WEP selected
When WEP is enabled, you can manually or automatically program the four data encryption keys.
These values must be identical on all PCs and Access Points in your network.
•
Manual - Enter 10 hexadecimal digits if 64 Bit WEP or 26 digits for 128 Bit WEP.
Hexadecimal digits are 0-9, a-f, or A-F.
Wireless Configuration
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
Automatic - Enter a word or group of printable characters in the Passphrase box and click the
Generate button.
Select which of the four keys will be active.
Click Apply to save any settings from this menu.
3-8
Wireless Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Protecting Your Network
This chapter describes how to use the basic firewall features of the DG824M Wireless ADSL
Modem Gateway to protect your network.
Protecting Access to Your DG824M Wireless ADSL Modem
Gateway
For security reasons, the gateway has its own user name and password. Also, after a period of
inactivity for a set length of time, the administrator login will automatically disconnect. When
prompted, enter admin for the gateway User Name and password for the gateway Password. You
can use procedures below to change the gateway's password and the amount of time for the
administrator’s login timeout.
Note: The user name and password are not the same as any user name or password your may use
to log in to your Internet connection.
NETGEAR recommends that you change this password to a more secure password. The ideal
password should contain no dictionary words from any language, and should be a mixture of both
upper and lower case letters, numbers, and symbols. Your password can be up to 30 characters.
Procedure 4-1: Changing the Built-In Password
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
Figure 4-1: Log in to the gateway
Protecting Your Network
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. From the Main Menu of the browser interface, under the Maintenance heading, select Set
Password to bring up the menu shown in Figure 4-2.
Figure 4-2: Set Password menu
3. To change the password, first enter the old password, and then enter the new password twice.
4. Click Apply to save your changes.
Note: After changing the password, you will be required to log in again to continue the
configuration. If you have backed up the gateway settings previously, you should do a new
backup so that the saved settings file includes the new password.
Procedure 4-1: Changing the Administrator Login Timeout
For security, the administrator's login to the gateway configuration will timeout after a period of
inactivity. To change the login timeout period:
1. In the Set Password menu, type a number in ‘Administrator login times out’ field.The
suggested default value is 5 minutes.
2. Click Apply to save your changes or click Cancel to keep the current period.
4-2
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Configuring Basic Firewall Services
Basic firewall services you can configure include access blocking and scheduling of firewall
security. These topics are presented below.
Blocking Keywords, Sites, and Services
The gateway provides a variety of options for blocking Internet based content and
communications services. With its content filtering feature, the DG824M gateway prevents
objectionable content from reaching your PCs. The Model RT311 router allows you to control
access to Internet content by screening for keywords within Web addresses. Key content filtering
options include:
•
•
•
Blocks access from your LAN to Internet locations that you specify as off-limits.
Keyword blocking of newsgroup names.
Outbound Services Blocking limits access from your LAN to Internet locations or services
that you specify as off-limits.
•
•
Denial of Service (DoS) protection. Automatically detects and thwarts Denial of Service
(DoS) attacks such as Ping of Death, SYN Flood, LAND Attack and IP Spoofing.
Blocks unwanted traffic from the Internet to your LAN.
The section below explains how to configure your gateway to perform these functions.
Procedure 4-2: Block Keywords and Sites
The DG824M gateway allows you to restrict access to Internet content based on functions such as
Java or Cookies, Web addresses and Web address keywords.
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
Protecting Your Network
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. Click on the Block Sites link of the Security menu.
Figure 4-3: Block Sites menu
3. To enable keyword blocking, check “Turn keyword blocking on”, enter a keyword or domain
in the Keyword box, click Add Keyword, then click Apply.
Some examples of Keyword application follow:
•
•
•
If the keyword “XXX” is specified, the URL <http://www.badstuff.com/xxx.html> is
blocked, as is the newsgroup alt.pictures.xxx.
If the keyword “.com” is specified, only websites with other domain suffixes (such as .edu
or .gov) can be viewed.
Enter the keyword “.” to block all Internet browsing access.
Up to 32 entries are supported in the Keyword list.
4. To delete a keyword or domain, select it from the list, click Delete Keyword, then click Apply.
5. To specify a Trusted User, enter that PC’s IP address in the Trusted User box and click Apply.
You may specify one Trusted User, which is a PC that will be exempt from blocking and
logging. Since the Trusted User will be identified by an IP address, you should configure that
PC with a fixed IP address.
4-4
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
6. Click Apply to save your settings.
Rules
Firewall rules are used to block or allow specific traffic passing through from one side to the other.
Inbound rules (WAN to LAN) restrict access by outsiders to private resources, selectively allowing
only specific outside users to access specific resources. Outbound rules (LAN to WAN) determine
what outside resources local users can have access to.
A firewall has two default rules, one for inbound traffic and one for outbound. The default rules of
the DG824M are:
•
•
Inbound: Block all access from outside except responses to requests from the LAN side.
Outbound: Allow all access from the LAN side to the outside.
You may define additional rules that will specify exceptions to the default rules. By adding custom
rules, you can block or allow access based on the service or application, source or destination IP
addresses, and time of day. You can also choose to log traffic that matches or does not match the
rule you have defined.
Protecting Your Network
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
To access the Rules configuration of the DG824M, click the Rules link on the main menu, then
click Add for either an Outbound or Inbound Service.
Figure 4-4: Rules menu
•
•
•
To edit an existing rule, select its button on the left side of the table and click Edit.
To delete an existing rule, select its button on the left side of the table and click Delete.
To move an existing rule to a different position in the table, select its button on the left side
of the table and click Move. At the script prompt, enter the number of the desired new
position and click OK.
4-6
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Inbound Rules (Port Forwarding)
Because the DG824M uses Network Address Translation (NAT), your network presents only one
IP address to the Internet, and outside users cannot directly address any of your local computers.
However, by defining an inbound rule you can make a local server (for example, a web server or
game server) visible and available to the Internet. The rule tells the gateway to direct inbound
traffic for a particular service to one local server based on the destination port number. This is also
known as port forwarding.
Note: Some residential broadband ISP accounts do not allow you to run any server
processes (such as a Web or FTP server) from your location. Your ISP may periodically
check for servers and may suspend your account if it discovers any active services at
your location. If you are unsure, refer to the Acceptable Use Policy of your ISP.
Remember that allowing inbound services opens holes in your firewall. Only enable those ports
Inbound Rule Example: A Local Public Web Server
If you host a public web server on your local network, you can define a rule to allow inbound web
(HTTP) requests from any outside IP address to the IP address of your web server at any time of
day. This rule is shown in Figure 4-5:
Figure 4-5: Rule example: A Local Public Web Server
Protecting Your Network
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The parameters are:
•
•
Service
From this list, select the application or service to be allowed or blocked. The list already
displays many common services, but you are not limited to these choices. Use the Add
Services menu to add any additional services or applications that do not already appear.
Action
Choose how you would like this type of traffic to be handled. You can block or allow
always, or you can choose to block or allow according to the schedule you have defined in
the Schedule menu.
•
•
Send to LAN Server
Enter the IP address of the PC or Server on your LAN which will receive the
inbound traffic covered by this rule.
WAN Users
These settings determine which packets are covered by the rule, based on their
source (WAN) IP address. Select the desired option:
•
•
•
Any All IP addresses are covered by this rule.
Address range If this option is selected, you must enter the "Start" and "Finish" fields.
Single address Enter the required address in the "Start" fields.
•
Log
You can select whether the traffic will be logged. The choices are:
•
•
•
•
Never - no log entries will be made for this service.
Always - any traffic for this service type will be logged.
Match - traffic of this type which matches the parameters and action will be logged.
Not match - traffic of this type which does not match the parameters and action will be
logged.
4-8
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Inbound Rule Example: Allowing Videoconference from Restricted Addresses
If you want to allow incoming videoconferencing to be initiated from a restricted range of outside
IP addresses, such as from a branch office, you can create an inbound rule. In the example shown
in Figure 4-6, CU-SeeMe connections are allowed only from a specified range of external IP
addresses. In this case, we have also specified logging of any incoming CU-SeeMe requests that
do not match the allowed parameters.
Figure 4-6: Rule example: Videoconference from Restricted Addresses
Considerations for Inbound Rules
•
•
•
If your external IP address is assigned dynamically by your ISP, the IP address may change
periodically as the DHCP lease expires. Consider using the Dynamic DNS feature in the
If the IP address of the local server PC is assigned by DHCP, it may change when the PC is
rebooted. To avoid this, use the Reserved IP address feature in the LAN IP menu to keep the
PC’s IP address constant.
Local PCs must access the local server using the PCs’ local LAN address (192.168.0.11 in the
example in Figure 4-6 above). Attempts by local PCs to access the server using the external
WAN IP address will fail.
Protecting Your Network
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Outbound Rules (Service Blocking)
The DG824M allows you to block the use of certain Internet services by PCs on your network.
This is called service blocking or port filtering. You can define an outbound rule to block Internet
access from a local PC based on:
•
•
•
•
the IP address of the local PC (source address)
the IP address of the Internet site being contacted (destination address)
the time of day
the type of service being requested (service port number)
Following is an application example of outbound rules:
Outbound Rule Example: Blocking Instant Messenger
If you want to block Instant Messenger usage by employees during working hours, you can create
an outbound rule to block that application from any internal IP address to any external address
according to the schedule that you have created in the Schedule menu. You can also have the
gateway log any attempt to use Instant Messenger during that blocked period.
Figure 4-7: Rule example: Blocking Instant Messenger
4-10
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The parameters are:
•
•
•
Service
From this list, select the application or service to be allowed or blocked. The list already
displays many common services, but you are not limited to these choices. Use the Add
Services menu to add any additional services or applications that do not already appear.
Action
Choose how you would like this type of traffic to be handled. You can block or allow
always, or you can choose to block or allow according to the schedule you have defined in
the Schedule menu.
LAN Users
These settings determine which packets are covered by the rule, based on their
source LAN IP address. Select the desired option:
•
•
•
Any All IP addresses are covered by this rule.
Address range If this option is selected, you must enter the "Start" and "Finish" fields.
Single address Enter the required address in the "Start" fields.
•
WAN Users
These settings determine which packets are covered by the rule, based on their
destination WAN IP address. Select the desired option:
•
•
•
Any All IP addresses are covered by this rule.
Address range If this option is selected, you must enter the "Start" and "Finish" fields.
Single address Enter the required address in the "Start" fields.
•
Log
You can select whether the traffic will be logged. The choices are:
•
•
•
•
Never - no log entries will be made for this service.
Always - any traffic for this service type will be logged.
Match - traffic of this type which matches the parameters and action will be logged.
Not match - traffic of this type which does not match the parameters and action will be
logged.
Protecting Your Network
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Order of Precedence for Rules
As you define new rules, they are added to the tables in the Rules menu, as shown in Figure 4-8:
Figure 4-8: Rules table with examples
For any traffic attempting to pass through the firewall, the packet information is subjected to the
rules in the order shown in the Rules Table, beginning at the top and proceeding to the default rules
at the bottom. In some cases, the order of precedence of two or more rules may be important in
determining the disposition of a packet. The Move button allows you to relocate a defined rule to a
new position in the table.
4-12
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Services
Services are functions performed by server computers at the request of client computers. For
example, Web servers serve web pages, time servers serve time and date information, and game
hosts serve data about other players’ moves. When a computer on the Internet sends a request for
service to a server computer, the requested service is identified by a service or port number. This
number appears as the destination port number in the transmitted IP packets. For example, a packet
that is sent with destination port number 80 is an HTTP (Web server) request.
The service numbers for many common protocols are defined by the Internet Engineering Task
Force (IETF) and published in RFC1700, “Assigned Numbers.” Service numbers for other
applications are typically chosen from the range 1024 to 65535 by the authors of the application.
Although the DG824M already holds a list of many service port numbers, you are not limited to
these choices. Use the procedure below to create your own service definitions.
Procedure 4-3: Define Services
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
2. Click on the Services link of the Security menu to display the Services menu shown in
Figure 4-9:
Figure 4-9: Services menu
•
•
To create a new Service, click the Add button.
To edit an existing Service, select its button on the left side of the table and click Edit.
Protecting Your Network
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
To delete an existing Service, select its button on the left side of the table and click Delete.
3. Modify the menu shown below for defining or editing a service.
Figure 4-10: Add Services menu
4. Click Apply to save your changes.
Setting Times and Scheduling Firewall Services
The DG824M gateway uses the Network Time Protocol (NTP) to obtain the current time and date
from one of several Network Time Servers on the Internet. In order to localize the time for your
log entries, you must select your Time Zone from the list.
Procedure 4-4: Setting Your Time Zone
In order to localize the time for your log entries, you must specify your Time Zone:
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
4-14
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. Click on the Schedule link of the Security menu to display menu shown below.
Figure 4-11: Schedule Services menu
3. Select your Time Zone. This setting will be used for the blocking schedule according to your
local time zone and for time-stamping log entries.
Check the Daylight Savings Time box if your time zone is currently in daylight savings time.
Note: If your region uses Daylight Savings Time, you must manually check Adjust for
Daylight Savings Time on the first day of Daylight Savings Time, and uncheck it at the end.
Enabling Daylight Savings Time will cause one hour to be added to the standard time.
4. The gateway has a list of publicly available NTP servers. If you would prefer to use a
particular NTP server as the primary server, enter its IP address under Use this NTP Server.
5. Click Apply to save your settings.
Protecting Your Network
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 4-5: Scheduling Firewall Services
If you enabled services blocking in the Block Services menu or Port forwarding in the Ports menu,
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
2. Click on the Schedule link of the Security menu to display menu shown above in the Schedule
Services menu.
3. To block Internet services based on a schedule, select Every Day or select one or more days. If
you want to limit access completely for the selected days, select All Day. Otherwise, to limit
access during certain times for the selected days, enter Start Blocking and End Blocking times.
Note: Enter the values as 24-hour time. For example, 10:30 am would be 10 hours and 30
minutes and 10:30 pm would be 22 hours and 30 minutes.
4. Click Apply to save your changes.
4-16
Protecting Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Managing Your Network
This chapter describes how to perform network management tasks with your DG824M Wireless
ADSL Modem Gateway.
Backing Up, Restoring, or Erasing Your Settings
The configuration settings of the DG824M gateway are stored in a configuration file in the
gateway. This file can be backed up to your computer, restored, or reverted to factory default
settings. The procedures below explain how to do these tasks.
Procedure 5-6: Backup the Configuration to a File
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
Managing Your Network
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. From the Maintenance heading of the Main Menu, select the Settings Backup menu as seen in
Figure 5-1.
Figure 5-1: Settings Backup menu
3. Click Backup to save a copy of the current settings.
4. Store the .cfgfile on a computer on your network.
5-2
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 5-7: Restore a Configuration from a File
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
2. From the Maintenance heading of the Main Menu, select the Settings Backup menu as seen in
Figure 5-1.
3. Enter the full path to the file on your network or click the Browse button to browse to the file.
4. When you have located the .cfgfile, click the Restore button to upload the file to the
gateway.
5. The gateway will then reboot automatically.
Procedure 5-8: Erase the Configuration
It is sometimes desirable to restore the gateway to the factory default settings. This can be done by
using the Erase function.
1. To erase the configuration, from the Maintenance menu Settings Backup link, click the Erase
button on the screen.
After an erase, the gateway's password will be password, the LAN IP address will be
192.168.0.1, and the router's DHCP client will be enabled.
Note: To restore the factory default configuration settings without knowing the login password or
IP address, you must use the Default Reset button on the rear panel of the gateway. See “DG824M
Rear Panel“ on page 1-8.
Upgrading the Gateway’s Firmware
The software of the DG824M gateway is stored in FLASH memory, and can be upgraded as new
software is released by NETGEAR.
Managing Your Network
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Upgrade files can be downloaded from NETGEAR's website. If the upgrade file is compressed
(.ZIP file), you must first extract the binary (.BIN or .IMG) file before uploading it to the gateway.
Procedure 5-1: Gateway Upgrade
Note: NETGEAR recommends that you back up your configuration before doing a firmware
upgrade. After the upgrade is complete, you may need to restore your configuration settings.
1. Download and unzip the new software file from NETGEAR.
The Web browser used to upload new firmware into the gateway must support HTTP uploads.
NETGEAR recommends using Microsoft Internet Explorer 5.0 or Netscape Navigator 4.7 and
above.
2. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
3. From the Main Menu of the browser interface, under the Maintenance heading, select the
Gateway Upgrade heading to display the menu shown in Figure 5-2.
Figure 5-2: Gateway Upgrade menu
4. In the Gateway Upgrade menu, click the Browse to locate the binary (.BIN or .IMG) upgrade
file.
5. Click Upload.
Note: When uploading software to the gateway, it is important not to interrupt the Web browser by
closing the window, clicking a link, or loading a new page. If the browser is interrupted, it may
corrupt the software. When the upload is complete, your gateway will automatically restart. The
upgrade process will typically take about one minute. In some cases, you may need to clear the
configuration and reconfigure the gateway after upgrading.
5-4
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Network Management Information
The DG824M provides a variety of status and usage information which is discussed below.
Viewing Gateway Status and Usage Statistics
From the Main Menu, under Maintenance, select Gateway Status to view the screen in Figure 5-3.
Figure 5-3: Gateway Status screen
The Router Status menu provides a limited amount of status and usage information. From the
Main Menu of the browser interface, under Maintenance, select Router Status to view the status
screen, shown in Figure 5-3.
Managing Your Network
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
This screen shows the following parameters:
Table 5-1.
Field
Menu 3.2 - Gateway Status Fields
Description
System Name
Firmware Version
WAN Port
The Host Name assigned to the gateway in the Basic Settings menu.
This field displays the gateway firmware version.
These parameters apply to the Internet (WAN) port of the gateway.
MAC Address
This field displays the Ethernet MAC address being used by the Internet
(WAN) port of the gateway.
IP Address
This field displays the IP address being used by the Internet (WAN) port
of the gateway. If no address is shown, the gateway cannot connect to
the Internet.
DHCP
If None, the gateway will use a fixed IP address on the WAN.
If Client, the gateway will obtain an IP address dynamically from the ISP
IP Subnet Mask
This field displays the IP Subnet Mask being used by the Internet (WAN)
port of the gateway.
Domain Name Servers
(DNS)
This field displays the DNS Server IP addresses being used by the
gateway. These addresses are usually obtained dynamically from the
ISP.
LAN Port
These parameters apply to the Local (WAN) port of the gateway.
MAC Address
This field displays the Ethernet MAC address being used by the Local
(LAN) port of the gateway.
IP Address
IP Subnet Mask
DHCP
This field displays the IP address being used by the Local (LAN) port of
the gateway. The default is 192.168.0.1
This field displays the IP Subnet Mask being used by the Local (LAN)
port of the gateway. The default is 255.255.255.0
If OFF, the gateway will not assign IP addresses to PCs on the LAN.
If ON, the gateway will assign IP addresses to PCs on the LAN.
ADSL Modem
ADSL Firmware Version
Modem Status
Downstream Speed
Upstream Speed
VPI
These parameters apply to the Local (WAN) port of the gateway.
The version of the firmware.
The connection status of the modem.
The speed at which the modem is receiving data from the ADSL line.
The speed at which the modem is transmitting data to the ADSL line.
The VPI setting.
VCI
The VCI setting.
5-6
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Click on the “Show Statistics” button to display gateway usage statistics, as shown in Figure 5-3
below:
Figure 5-4: Gateway Statistics screen
This screen shows the following statistics:.
Table 5-1.
Field
Gateway Statistics Fields
Description
WAN, LAN, or
Serial Port
The statistics for the WAN (Internet), LAN (local), and Serial ports. For each port, the
screen displays:
Status
TxPkts
The link status of the port.
The number of packets transmitted on this port since reset or manual clear.
The number of packets received on this port since reset or manual clear.
The number of collisions on this port since reset or manual clear.
The current line utilization—percentage of current bandwidth used on this port.
The average line utilization —average CLU for this port.
The time elapsed since this port acquired link.
RxPkts
Collisions
Tx B/s
Tx B/s
Up Time
System up Time
Poll Interval
The time elapsed since the last power cycle or reset.
Specifies the intervals at which the statistics are updated in this window. Click on Stop
to freeze the display.
Managing Your Network
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Click on the “Show WAN Status” button to display gateway WAN connection status, as shown in
Figure 5-5 below:
Figure 5-5: Gateway WAN Status screen
Clicking the Renew button updates the status information.
This screen shows the following statistics:.
Table 5-1.
Gateway Statistics Fields
Field
Description
Connection Time
The time elapsed since the last connection to the Internet via the ADSL port.
Connection Method The method the ADSL port acquired its TCP/IP configuration.
IP Address
The IP Address assigned to the WAN port by the ADSL Internet Service Provider.
Then Network Mask assigned to the WAN port by the ADSL Internet Service Provider.
Network Mask
Default Gateway
Then Default Gateway router assigned to the WAN port by the ADSL Internet Service
Provider.
5-8
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Viewing Attached Devices
The Attached Devices menu contains a table of all IP devices that the gateway has discovered on
the local network. From the Main Menu of the browser interface, under the Maintenance heading,
select Attached Devices to view the table, shown in Figure 5-6
Figure 5-6: Attached Devices menu
For each device, the table shows the IP address, NetBIOS Host Name, if available, and the
Ethernet MAC address. Note that if the gateway is rebooted, the table data is lost until the gateway
rediscovers the devices. To force the gateway to look for attached devices, click the Refresh
button.
Managing Your Network
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Viewing, Selecting, and Saving Logged Information
The gateway will log security-related events such as denied incoming service requests, hacker
probes, and administrator logins. If you enabled content filtering in the Block Sites menu, the Logs
page shows you when someone on your network tried to access a blocked site. If you enabled
e-mail notification, you'll receive these logs in an e-mail message. If you don't have e-mail
notification enabled, you can view the logs here. An example is shown below.
Figure 5-7: Security Logs menu
5-10
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Log entries are described in Table 5-1
Table 5-1.
Security Log entry descriptions
Field
Description
Date and Time
The date and time the log entry was recorded.
The type of event and what action was taken if any.
Description or
Action
Source IP
The IP address of the initiating device for this log entry.
Source port and
interface
The service port number of the initiating device, and whether it
originated from the LAN or WAN
Destination
Destination port The service port number of the destination device, and whether
and interface it’s on the LAN or WAN.
Log action buttons are described in Table 5-8
Table 5-8:
Security Log action buttons
Field
Description
Refresh
Clear Log
Send Log
Apply
Click this button to refresh the log screen.
Click this button to clear the log entries.
Click this button to email the log immediately.
Click this button to apply the current settings.
Click this button to clear the current settings.
Cancel
Selecting What Information to Log
Besides the standard information listed above, you can choose to log additional information. Those
optional selections are as follows:
•
•
•
All incoming and outgoing traffic
Attempted access to blocked site
Connections to the Web-based interface of this Router
Managing Your Network
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
Router operation (start up, get time, etc.)
Known DoS attacks and Port Scans
Saving Log Files on a Server
You can choose to write the logs to a PC running a syslog program. To activate this feature, check
the box under Syslog and enter the IP address of the server where the log file will be written.
Examples of log messages
Following are examples of log messages. In all cases, the log entry shows the timestamp as: Day,
Year-Month-Date Hour:Minute:Second
Activation and Administration
Tue, 2002-05-21 18:48:39 - NETGEAR activated
[This entry indicates a power-up or reboot with initial time entry.]
Tue, 2002-05-21 18:55:00 - Administrator login successful - IP:192.168.0.2
Thu, 2002-05-21 18:56:58 - Administrator logout - IP:192.168.0.2
[This entry shows an administrator logging in and out from IP address 192.168.0.2.]
Tue, 2002-05-21 19:00:06 - Login screen timed out - IP:192.168.0.2
[This entry shows a time-out of the administrator login.]
Wed, 2002-05-22 22:00:19 - Log emailed
[This entry shows when the log was emailed.]
Dropped Packets
Wed, 2002-05-22 07:15:15 - TCP packet dropped - Source:64.12.47.28,4787,WAN -
Destination:134.177.0.11,21,LAN - [Inbound Default rule match]
Sun, 2002-05-22 12:50:33 - UDP packet dropped - Source:64.12.47.28,10714,WAN -
Destination:134.177.0.11,6970,LAN - [Inbound Default rule match]
Sun, 2002-05-22 21:02:53 - ICMP packet dropped - Source:64.12.47.28,0,WAN -
Destination:134.177.0.11,0,LAN - [Inbound Default rule match]
[These entries show an inbound FTP (port 21) packet, UDP packet (port 6970), and ICMP
packet (port 0) being dropped as a result of the default inbound rule, which states that all
inbound packets are denied.]
5-12
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Enabling Security Event E-mail Notification
In order to receive logs and alerts by e-mail, you must provide your e-mail information in the
E-Mail subheading:
•
•
Turn e-mail notification on
Check this box if you wish to receive e-mail logs and alerts from the gateway.
Your outgoing mail server
Enter the name or IP address of your ISP’s outgoing (SMTP) mail server (such as
mail.myISP.com). You may be able to find this information in the configuration menu of your
e-mail program. If you leave this box blank, log and alert messages will not be sent via e-mail.
•
Send to this e-mail address
Enter the e-mail address to which logs and alerts are sent. This e-mail address will also be used
as the From address. If you leave this box blank, log and alert messages will not be sent via
e-mail.
You can specify that logs are automatically sent to the specified e-mail address with these options:
Managing Your Network
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
Send alert immediately
Check this box if you would like immediate notification of a significant security event, such as
a known attack, port scan, or attempted access to a blocked site.
Send logs according to this schedule
Specifies how often to send the logs: Hourly, Daily, Weekly, or When Full.
–
Day for sending log
Specifies which day of the week to send the log. Relevant when the log is sent weekly or
daily.
–
Time for sending log
Specifies the time of day to send the log. Relevant when the log is sent daily or weekly.
If the Weekly, Daily or Hourly option is selected and the log fills up before the specified
period, the log is automatically e-mailed to the specified e-mail address. After the log is sent,
the log is cleared from the gateway’s memory. If the gateway cannot e-mail the log file, the log
buffer may fill up. In this case, the gateway overwrites the log and discards its contents.
5-14
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Running Diagnostic Utilities and Rebooting the Router
The DG824M gateway has a diagnostics feature. You can use the diagnostics menu to perform the
following functions from the gateway:
•
•
Ping an IP Address to test connectivity to see if you can reach a remote host.
Perform a DNS Lookup to test if an Internet name resolves to an IP address to verify that the
DNS server configuration is working.
•
•
•
Display the Routing Table to identify what other routers the router is communicating with.
Reboot the Router to enable new network configurations to take effect or to clear problems
with the router’s network connection.
From the Main Menu of the browser interface, under the Maintenance heading, select the Router
Diagnostics heading to display the menu shown in Figure 5-9.
Figure 5-9: Diagnostics menu
Managing Your Network
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Enabling Remote Management
Using the Remote Management page, you can allow a user or users on the Internet to configure,
upgrade and check the status of your NETGEAR Cable/DSL ProSafe VPN Firewall.
Note: Be sure to change the router's default password to a very secure password. The
ideal password should contain no dictionary words from any language, and should be a
mixture of letters (both upper and lower case), numbers, and symbols. Your password
can be up to 30 characters.
Procedure 5-2: Configure Remote Management
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
2. From the Advanced section of the main menu, click on the Remote Management link.
3. Select the Allow Remote Management check box.
4. Specify what external addresses will be allowed to access the gateway’s remote management.
For security, NETGEAR recommends that you restrict access to as few external IP addresses
as practical.
a. To allow access from any IP address on the Internet, select Everyone.
b. To allow access from a range of IP addresses on the Internet, select IP address range.
Enter a beginning and ending IP address to define the allowed range.
c. To allow access from a single IP address on the Internet, select Only this PC.
Enter the IP address that will be allowed access.
5. Specify the Port Number that will be used for accessing the management interface.
Web browser access normally uses the standard HTTP service port 80. For greater security,
you can change the remote management web interface to a custom port by entering that
number in the box provided. Choose a number between 1024 and 65535, but do not use the
number of any common service port. The default is 8080, which is a common alternate for
HTTP.
5-16
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
6. Click Apply to have your changes take effect.
When accessing your gateway from the Internet, you will type your gateway's WAN IP
address in your browser's Address (in IE) or Location (in Netscape) box, followed by a colon
(:) and the custom port number. For example, if your external address is 134.177.0.123 and
you use port number 8080, enter in your browser:
http://134.177.0.123:8080
Note: In this case, the http:// must be included in the address.
Managing Your Network
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
5-18
Managing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Advanced Configuration
This chapter describes how to configure the advanced features of your DG824M Wireless ADSL
Modem Gateway.
Configuring Advanced Security
The DG824M Wireless ADSL Modem Gateway provides a variety of advanced features, such as:
•
•
Setting up a Demilitarized Zone (DMZ) Server
The flexibility of configuring your LAN TCP/IP settings
These features are discussed below.
Setting Up A Default DMZ Server
The Default DMZ Server feature is helpful when using some online games and videoconferencing
applications that are incompatible with NAT. The gateway is programmed to recognize some of
these applications and to work properly with them, but there are other applications that may not
function well. In some cases, one local PC can run the application properly if that PC’s IP address
is entered as the Default DMZ Server.
Note: For security, you should avoid using the Default DMZ Server feature. When a
computer is designated as the Default DMZ Server, it loses much of the protection of the
firewall, and is exposed to many exploits from the Internet. If compromised, the
computer can be used to attack your network.
Advanced Configuration
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Incoming traffic from the Internet is normally discarded by the gateway unless the traffic is a
response to one of your local computers or a service that you have configured in the Ports menu.
Instead of discarding this traffic, you can have it forwarded to one computer on your network. This
computer is called the Default DMZ Server.
Procedure 6-1: Configuring A Default DMZ Server.
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever Password and LAN
address you have chosen for the gateway.
2. From the Main Menu, under Security, click the Rules link to view the menu, shown in
Figure 6-1
Figure 6-1: Security Rules Menu
3. Click Default DMZ Server.
4. Type the IP address for that server.
5. Click Apply to save your changes.
Respond to Ping on Internet WAN Port
If you want the gateway to respond to a 'ping' from the Internet, click the ‘Respond to Ping on
Internet WAN Port’ check box. This should only be used as a diagnostic tool, since it allows your
gateway to be discovered. Don't check this box unless you have a specific reason to do so.
6-2
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Configuring LAN IP Settings
The LAN IP Setup menu allows configuration of LAN IP services such as DHCP and RIP. These
features can be found under the Advanced heading in the Main Menu of the browser interface.
LAN TCP/IP Setup
The gateway is shipped preconfigured to use private IP addresses on the LAN side, and to act as a
DHCP server. The gateway’s default LAN IP configuration is:
•
•
LAN IP addresses—192.168.0.1
Subnet mask—255.255.255.0
These addresses are part of the IETF-designated private address range for use in private networks,
and should be suitable in most applications. If your network has a requirement to use a different IP
addressing scheme, you can make those changes in this menu.
Figure 6-2: LAN IP Setup Menu
Advanced Configuration
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The LAN TCP/IP Setup parameters are:
•
IP Address
This is the LAN IP address of the gateway.
•
IP Subnet Mask
This is the LAN Subnet Mask of the gateway. Combined with the IP address, the IP Subnet
Mask allows a device to know which other addresses are local to it, and which must be reached
through a gateway or router.
•
RIP Direction
RIP (Router Information Protocol) allows a router to exchange routing information with other
routers. The RIP Direction selection controls how the gateway sends and receives RIP packets.
Both is the default.
— When set to Both or Out Only, the gateway will broadcast its routing table periodically.
— When set to Both or In Only, it will incorporate the RIP information that it receives.
— When set to None, it will not send any RIP packets and will ignore any RIP packets
received.
•
RIP Version
This controls the format and the broadcasting method of the RIP packets that the router sends.
It recognizes both formats when receiving. By default, this is set for RIP-1.
— RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you
have an unusual network setup.
— RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2
format.
— RIP-2B uses subnet broadcasting.
— RIP-2M uses multicasting.
Note: If you change the LAN IP address of the gateway while connected through the
browser, you will be disconnected. You must then open a new connection to the new IP
address and log in again.
MTU Size
The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 Bytes. For
PPPoE, the gateway adjusts the MTU size automatically. Changing this is rarely required, and
should not be done unless you are sure it is necessary for your ISP connection.
6-4
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Any packets sent through the gateway that are larger than the configured MTU size will be
repackaged into smaller packets to meet the MTU requirement. To change the MTU size:
1. Under MTU Size, select Custom.
2. Enter a new size between 64 and 1500. For PPPoE, use 1492.
3. Click Apply to save the new configuration.
DHCP
By default, the gateway will function as a DHCP (Dynamic Host Configuration Protocol) server,
the router's LAN. The assigned default gateway address is the LAN address of the gateway. IP
addresses will be assigned to the attached PCs from a pool of addresses specified in this menu.
Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.
For most applications, the default DHCP and TCP/IP settings of the gateway are satisfactory. See
“IP Configuration by DHCP“ on page B-10” for an explanation of DHCP and information about
how to assign IP addresses for your network.
Use Gateway as DHCP server
If another device on your network will be the DHCP server, or if you will manually configure the
network settings of all of your computers, clear the ‘Use router as DHCP server’ check box.
Otherwise, leave it checked.
Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP
Address. These addresses should be part of the same IP address subnet as the gateway’s LAN IP
address. Using the default addressing scheme, you should define a range between 192.168.0.2 and
192.168.0.253, although you may wish to save part of the range for devices with fixed addresses.
The gateway will deliver the following parameters to any LAN device that requests DHCP:
•
•
•
•
An IP Address from the range you have defined
Subnet Mask
Gateway IP Address is the gateway’s LAN IP address
Primary DNS Server, if you entered a Primary DNS address in the Basic Settings menu;
otherwise, the gateway’s LAN IP address
•
Secondary DNS Server, if you entered a Secondary DNS address in the Basic Settings menu
Advanced Configuration
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
WINS Server, short for Windows Internet Naming Service Server, determines the IP
address associated with a particular Windows computer. A WINS server records and
reports a list of names and IP address of Windows PCs on its local network. If you
connect to a remote network that contains a WINS server, enter the server’s IP address
here. This allows your PCs to browse the network using the Network Neighborhood
feature of Windows.
Reserved IP addresses
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the
same IP address each time it access the gateway’s DHCP server. Reserved IP addresses should be
assigned to servers that require permanent IP settings.
To reserve an IP address:
1. Click the Add button.
2. In the IP Address box, type the IP address to assign to the PC or server.
Choose an IP address from the router’s LAN subnet, such as 192.168.0.X.
3. Type the MAC Address of the PC or server.
Tip: If the PC is already present on your network, you can copy its MAC address from the
Attached Devices menu and paste it here.
4. Click Apply to enter the reserved address into the table.
Note: The reserved address will not be assigned until the next time the PC contacts the router's
DHCP server. Reboot the PC or access its IP configuration and force a DHCP release and
renew.
To edit or delete a reserved address entry:
1. Click the button next to the reserved address you want to edit or delete.
2. Click Edit or Delete.
Procedure 6-1: Configure LAN TCP/IP Setup
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
6-6
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
2. From the Main Menu, under Advanced, click the LAN IP Setup link to view the menu, shown
in Figure 6-3
Figure 6-3: LAN IP Setup Menu
3. Enter the TCP/IP, MTU, DHCP, or Reserved IP parameters.
4. Click Apply to save your changes.
Configuring Dynamic DNS
If your network has a permanently assigned IP address, you can register a domain name and have
that name linked with your IP address by public Domain Name Servers (DNS). However, if your
Internet account uses a dynamically assigned IP address, you will not know in advance what your
IP address will be, and the address can change frequently. In this case, you can use a commercial
dynamic DNS service, who will allow you to register your domain to their IP address, and will
forward traffic directed at your domain to your frequently-changing IP address.
Advanced Configuration
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The gateway contains a client that can connect to a dynamic DNS service provider. To use this
feature, you must select a service provider and obtain an account with them. After you have
configured your account information in the gateway, whenever your ISP-assigned IP address
changes, your gateway will automatically contact your dynamic DNS service provider, log in to
your account, and register your new IP address.
Procedure 6-2: Configure Dynamic DNS
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
2. From the Main Menu of the browser interface, under Advanced, click on Dynamic DNS.
3. Access the website of one of the dynamic DNS service providers whose names appear in the
‘Select Service Provider’ box, and register for an account.
For example, for dyndns.org, go to www.dyndns.org.
4. Select the “Use a dynamic DNS service” check box.
5. Select the name of your dynamic DNS Service Provider.
6. Type the Host Name that your dynamic DNS service provider gave you.
The dynamic DNS service provider may call this the domain name. If your URL is
myName.dyndns.org, then your Host Name is “myName.”
7. Type the User Name for your dynamic DNS account.
8. Type the Password (or key) for your dynamic DNS account.
9. If your dynamic DNS provider allows the use of wildcards in resolving your URL, you may
select the Use wildcards check box to activate this feature.
For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same
IP address as yourhost.dyndns.org
10. Click Apply to save your configuration.
Note: If your ISP assigns a private WAN IP address such as 192.168.x.x or 10.x.x.x, the
dynamic DNS service will not work because private addresses will not be routed on the
Internet.
6-8
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Using Static Routes
Static Routes provide additional routing information to your gateway. Under normal
circumstances, the gateway has adequate routing information after it has been configured for
Internet access, and you do not need to configure additional static routes. You must configure
static routes only for unusual cases such as multiple routers or multiple IP subnets located on your
network.
Static Route Example
As an example of when a static route is needed, consider the following case:
•
•
Your primary Internet access is through a cable modem to an ISP.
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.0.100.
•
Your company’s network is 134.177.0.0.
When you first configured your gateway, two implicit static routes were created. A default route
was created with your ISP as the gateway, and a second static route was created to your local
network for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on
the 134.177.0.0 network, your gateway will forward your request to the ISP. The ISP forwards
your request to the company where you are employed, and the request will likely be denied by the
company’s firewall.
In this case you must define a static route, telling your gateway that 134.177.0.0 should be
accessed through the ISDN router at 192.168.0.100. The static route would look like Figure 6-5.
In this example:
•
•
•
The Destination IP Address and IP Subnet Mask fields specify that this static route applies to
all 134.177.x.x addresses.
The Gateway IP Address fields specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.0.100.
A Metric value of 1 will work since the ISDN router is on the LAN.
This represents the number of routers between your network and the destination. This is a
direct connection so it is set to 1.
•
Private is selected only as a precautionary security measure in case RIP is activated.
Advanced Configuration
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Procedure 6-3: Configuring Static Routes
1. Log in to the gateway at its default LAN address of http://192.168.0.1 with its default User
Name of admin, default password of password, or using whatever User Name, Password and
LAN address you have chosen for the gateway.
2. From the Main Menu of the browser interface, under Advanced, click on Static Routes to view
the Static Routes menu, shown in Figure 6-4.
Figure 6-4: Static Routes Table
3. To add or edit a Static Route:
a. Click the Edit button to open the Edit Menu, shown in Figure 6-5.
Figure 6-5: Static Route Entry and Edit Menu
b. Type a route name for this static route in the Route Name box under the table.
This is for identification purpose only.
6-10
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
c. Select Active to make this route effective.
d. Select Private if you want to limit access to the LAN only.
The static route will not be reported in RIP.
e. Type the Destination IP Address of the final destination.
f. Type the IP Subnet Mask for this destination.
If the destination is a single host, type 255.255.255.255.
g. Type the Gateway IP Address, which must be a router on the same LAN segment as the
gateway.
h. Type a number between 1 and 15 as the Metric value.
This represents the number of routers between your network and the destination. Usually,
a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
4. Click Apply to have the static route entered into the table.
Advanced Configuration
6-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
6-12
Advanced Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
Troubleshooting
This chapter gives information about troubleshooting your DG824M Wireless ADSL Modem
the problem. For the common problems listed, go to the section indicated.
•
•
Is the gateway on?
Have I connected the gateway correctly?
Go to “Basic Functioning“ on page 7-1.
•
•
I can’t access the gateway’s configuration with my browser.
Go to “Troubleshooting the Web Configuration Interface“ on page 7-3.
I’ve configured the gateway but I can’t access the Internet.
Go to “Troubleshooting the ISP Connection“ on page 7-4.
I can’t remember the gateway’s configuration password.
I want to clear the configuration and start over again.
Go to “Restoring the Default Configuration and Password“ on page 7-9.
•
•
Basic Functioning
After you turn on power to the gateway, the following sequence of events should occur:
1. When power is first applied, verify that the Power LED
is on.
2. Verify that the Test LED
procedure is running.
lights within a few seconds, indicating that the self-test
3. After approximately 10 seconds, verify that:
a. The Test LED is not lit.
Troubleshooting
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
b. The LAN port LEDs are lit for any local ports that are connected.
c. The WAN port LED is lit.
If a port’s LED is lit, a link has been established to the connected device. If a LAN port is
connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the
LED will be amber.
If any of these conditions does not occur, refer to the appropriate following section.
Power LED Not On
If the Power and other LEDs are off when your gateway is turned on:
•
Make sure that the power cord is properly connected to your gateway and that the power
supply adapter is properly connected to a functioning power outlet.
•
Check that you are using the 12 V DC power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
Test LED Never Turns On or Test LED Stays On
When the gateway is turned on, the Test LED turns on for about 10 seconds and then turns off. If
the Test LED does not turn on, or if it stays on, there is a fault within the gateway.
If you experience problems with the Test LED:
•
Cycle the power to see if the gateway recovers and the LED blinks for the correct amount of
time.
If all LEDs including the Test LED are still on one minute after power up:
•
•
Cycle the power to see if the gateway recovers.
Clear the gateway’s configuration to factory defaults. This will set the gateway’s IP address to
192.168.0.1. This procedure is explained in “Using the Default Reset button“ on page 7-9.
If the error persists, you might have a hardware problem and should contact technical support.
LAN or WAN Port LEDs Not On
If either the LAN LEDs or WAN LED do not light when the Ethernet connection is made, check
the following:
7-2
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
Make sure that the Ethernet cable connections are secure at the gateway and at the hub or
workstation.
•
•
Make sure that power is turned on to the connected hub or workstation.
Be sure you are using the correct cable:
— When connecting the gateway’s WAN ADSL port, use the cable that was supplied with the
DG824M.
Troubleshooting the Web Configuration Interface
If you are unable to access the gateway’s Web Configuration interface from a PC on your local
network, check the following:
•
•
Make sure your PC’s IP address is on the same subnet as the gateway. If you are using the
recommended addressing scheme, your PC’s address should be in the range of 192.168.0.2 to
192.168.0.254. Refer to “Verifying TCP/IP Properties“ on page C-6 or “Verifying TCP/IP
Properties for Macintosh Computers“ on page C-17 to find your PC’s IP address. Follow the
instructions in Appendix C to configure your PC.
Note: If your PC’s IP address is shown as 169.254.x.x:
Recent versions of Windows and MacOS will generate and assign an IP address if the
computer cannot reach a DHCP server. These auto-generated addresses are in the range of
169.254.x.x. If your IP address is in this range, check the connection from the PC to the
gateway and reboot your PC.
•
•
If your gateway’s IP address has been changed and you don’t know the current IP address,
clear the gateway’s configuration to factory defaults. This will set the gateway’s IP address to
192.168.0.1. This procedure is explained in “Using the Default Reset button“ on page 7-9.
Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet
Explorer, click Refresh to be sure the Java applet is loaded.
•
•
Try quitting the browser and launching it again.
Make sure you are using the correct login information. The factory default login name is
admin and the password is password. Make sure that CAPS LOCK is off when entering this
information.
If the gateway does not save changes you have made in the Web Configuration Interface, check the
following:
Troubleshooting
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
When entering configuration settings, be sure to click the APPLY button before moving to
another menu or tab, or your changes are lost.
Click the Refresh or Reload button in the Web browser. The changes may have occurred, but
the Web browser may be caching the old configuration.
Troubleshooting the ISP Connection
If your gateway is unable to access the Internet, you should check the ADSL connection, then the
WAN TCP/IP connection.
ADSL link
If your gateway is unable to access the Internet, you should first determine whether you have an
ADSL link with the service provider. The state of this connection is indicated with the WAN LED.
WAN LED Green or Blinking Green
If your WAN LED is green or blinking green, then you have a good ADSL connection. You can be
confident that the service provider has connected your line correctly and that your wiring is
correct.
WAN LED Blinking Yellow
If your WAN LED is blinking yellow then your gateway is attempting to make an ADSL
connection with the service provider. The LED should turn green within several minutes.
If the WAN LED does not turn green, disconnect all telephones on the line. If this solves the
problem, reconnect the telephones one at a time, being careful to use a microfilter on each
telephone. If the microfilters are connected correctly, you should be able to connect all your
telephones.
If disconnecting telephones does not result in a green WAN LED there may be a problem with
your wiring. If the telephone company has tested the ADSL signal at your Network Interface
Device (NID), then you may have poor quality wiring in your house.
7-4
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
WAN LED Off
If the WAN LED is off, disconnect all telephones on the line. If this solves the problem, reconnect
the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters
are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green WAN LED the problem may be one of the
following:
•
•
Check that the telephone company has made the connection to your line and tested it.
Verify that you are connected to the correct telephone line. If you have more than one phone
line, be sure that you are connected to the line with the ADSL service. It may be necessary to
use a swapper if you ADSL signal is on pins 1 and 4 or the RJ-11 jack. The DG824M gateway
uses pins 2 and 3.
Obtaining a WAN IP Address
If your gateway is unable to access the internet, and your WAN LED is green or blinking green,
you should determine whether the gateway is able to obtain a WAN IP address from the ISP.
Unless you have been assigned a static IP address, your gateway must request an IP address from
the ISP. You can determine whether the request was successful using the browser interface.
To check the WAN IP address from the browser interface:
1. Launch your browser and select an external site such as www.netgear.com
2. Access the Main Menu of the gateway’s configuration at http://192.168.0.1
3. Under the Maintenance heading check that an IP address is shown for the WAN Port
If 0.0.0.0 is shown, your gateway has not obtained an IP address from your ISP.
If your gateway is unable to obtain an IP address from the ISP, the problem may be one of the
following:
•
•
•
Your ISP may require a Multiplexing Method or VPI/VCI parameter.
Verify with your ISP the Multiplexing Method and parameter value, and update the gateway’s
Basic Settings accordingly.
Your ISP may require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or PPP over ATM (PPPOA)
login.
If you have selected a login program, you may have incorrectly set the Service Name, User
Name and Password. See “Troubleshooting PPPoE or PPPoA”, below.
Troubleshooting
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
Your ISP may check for your PC's host name.
Assign the PC Host Name of your ISP account to the gateway in the browser-based Setup
Wizard.
Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for
your PC’s MAC address. In this case:
Inform your ISP that you have bought a new network device, and ask them to use the
gateway’s MAC address.
OR
Configure your gateway to spoof your PC’s MAC address. This can be done in the Basic
Settings menu. Refer to “Manually Configuring Your Internet Connection“ on page 2-17.
Troubleshooting PPPoE or PPPoA
The PPPoA or PPPoA connection can be debugged as follows:
1. Access the Main Menu of the gateways configuration at http://192.168.0.1.
2. Under the Maintenance heading, click the “Show WAN Status” button.
3. If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.
4. If any of the steps indicates “Failed”, you can attempt to reconnect by clicking “Connect”. The
gateway will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you may be using an incorrect Service Name, User
Name or Password. There also may be a provisioning problem with your ISP.
Note: Unless you connect manually, the gateway will not authenticate using PPPoE or
PPPoA until data is transmitted to the network.
Troubleshooting Internet Browsing
If your gateway can obtain an IP address but your PC is unable to load any web pages from the
Internet:
•
Your PC may not recognize any DNS server addresses.
7-6
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS
servers for your use. If you entered a DNS address during the gateway’s configuration, reboot
C-6. Alternatively, you may configure your PC manually with DNS addresses, as explained in
your operating system documentation.
•
Your PC may not have the gateway configured as its TCP/IP gateway.
If your PC obtains its information from the gateway by DHCP, reboot the PC and verify the
gateway address as described in “Verifying TCP/IP Properties“ on page C-6.
Troubleshooting a TCP/IP Network Using the Ping Utility
Most TCP/IP terminal devices and gateways contain a ping utility that sends an echo request
packet to the designated device. The device then responds with an echo reply. Troubleshooting a
TCP/IP network is made very easy by using the ping utility in your PC or workstation.
Testing the LAN Path to Your Router
You can ping the router from your PC to verify that the LAN path to your router is set up correctly.
To ping the router from a PC running Windows 95 or later:
1. From the Windows toolbar, click on the Start button and select Run.
2. In the field provided, type Ping followed by the IP address of the router, as in this example:
ping 192.168.0.1
3. Click on OK.
You should see a message like this one:
Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
Troubleshooting
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
— Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN
or WAN Port LEDs Not On” on page 7-2.
— Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and router.
•
Wrong network configuration
— Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation.
— Verify that the IP address for your router and your workstation are correct and that the
addresses are on the same subnet.
Testing the Path from Your PC to a Remote Device
After verifying that the LAN path works correctly, test the path from your PC to a remote device.
From the Windows run menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not
receive replies:
— Check that your PC has the IP address of your router listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information will not be visible in your
PC’s Network Control Panel. Verify that the IP address of the router is listed as the default
gateway as described in “Verifying TCP/IP Properties“ on page C-6.
— Check to see that the network address of your PC (the portion of the IP address specified
by the netmask) is different from the network address of the remote device.
— Check that your cable or DSL modem is connected and functioning.
— If your ISP assigned a host name to your PC, enter that host name as the Account Name in
the Basic Settings menu.
— Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs. Many
broadband ISPs restrict access by only allowing traffic from the MAC address of your
broadband modem, but some ISPs additionally restrict access to the MAC address of a
single PC connected to that modem. If this is the case, you must configure your router to
“clone” or “spoof” the MAC address from the authorized PC. Refer to “Manually
Configuring Your Internet Connection“ on page 2-17.
7-8
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Restoring the Default Configuration and Password
This section explains how to restore the factory default configuration settings, changing the
router’s administration password to password and the IP address to 192.168.0.1. You can erase the
current configuration and restore factory defaults in two ways:
•
Use the Erase function of the Web Configuration Manager (see “Backing Up, Restoring, or
Erasing Your Settings“ on page 5-1).
•
Use the Default Reset button on the rear panel of the router. Use this method for cases when
the administration password or IP address is not known.
Using the Default Reset button
To restore the factory default configuration settings without knowing the administration password
or IP address, you must use the Default Reset button on the rear panel of the router.
1. Press and hold the Default Reset button until the Test LED turns on (about 10 seconds).
2. Release the Default Reset button and wait for the router to reboot.
Problems with Date and Time
The E-Mail menu in the Content Filtering section displays the current date and time of day. The
DG824M gateway uses the Network Time Protocol (NTP) to obtain the current time from one of
several Network Time Servers on the Internet. Each entry in the log is stamped with the date and
time of day. Problems with the date and time function can include:
•
Date shown is January 1, 2000
Cause: The router has not yet successfully reached a Network Time Server. Check that your
Internet access settings are configured correctly. If you have just completed configuring the
router, wait at least five minutes and check the date and time again.
•
Time is off by one hour
Cause: The router does not automatically sense Daylight Savings Time. In the E-Mail menu,
check or uncheck the box marked “Adjust for Daylight Savings Time”.
Troubleshooting
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
7-10
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Technical Specifications
This appendix provides technical specifications for the DG824M Wireless ADSL Modem
Gateway.
Network Protocol and Standards Compatibility
Data and Routing Protocols:
TCP/IP, RIP-1, RIP-2, DHCP, PPP over Ethernet (PPPoE) or
PPP over ATM (PPPoA), RFC 1483 Bridged Ethernet
Power Adapter
North America:
United Kingdom, Australia:
Europe:
120V, 60 Hz, input
240V, 50 Hz, input
230V, 50 Hz, input
Japan:
100V, 50/60 Hz, input
15 V AC @ 1.0A output, 30W maximum
All regions (output):
Physical Specifications
Dimensions:
10" x 6.7" x 1.3"
255 mm x 169 mm x 34 mm
Weight:
1.4 lbs.
0.62 kg
Environmental Specifications
Operating temperature:
0° to 40° C (32º to 104º F)
Technical Specifications
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Operating humidity:
90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Meets requirements of:
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
Interface Specifications
LAN:
WAN:
10BASE-T or 100BASE-Tx, RJ-45
ADSL, Dual RJ-11, pins 2 and 3
T1.413, G.DMT, G.Lite
ITU Annex B
A-2
Technical Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Network and Routing Basics
This chapter provides an overview of IP networks, routing, and wireless networking.
Related Publications
As you read this document, you may be directed to various RFC documents for further
information. An RFC is a Request For Comment (RFC) published by the Internet Engineering
Task Force (IETF), an open organization that defines the architecture and operation of the Internet.
The RFC documents outline and define the standard protocols and procedures for the Internet. The
documents are listed on the World Wide Web at www.ietf.org and are mirrored and indexed at
many other sites worldwide.
Basic Router Concepts
Large amounts of bandwidth can be provided easily and relatively inexpensively in a local area
network (LAN). However, providing high bandwidth between a local network and the Internet can
be very expensive. Because of this expense, Internet access is usually provided by a slower-speed
wide-area network (WAN) link such as a cable or DSL modem. In order to make the best use of the
slower WAN link, a mechanism must be in place for selecting and transmitting only the data traffic
meant for the Internet. The function of selecting and forwarding this data is performed by a router.
Network and Routing Basics
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
What is a Router?
A router is a device that forwards traffic between networks based on network layer information in
the data and on routing tables maintained by the router. In these routing tables, a router builds up a
logical picture of the overall network by gathering and exchanging information with other routers
in the network. Using this information, the router chooses the best path for forwarding network
traffic.
Routers vary in performance and scale, number of routing protocols supported, and types of
physical WAN connection they support. The DG824M Wireless ADSL Modem Gateway is a small
office router that routes the IP protocol over a single-user broadband connection.
Routing Information Protocol
One of the protocols used by a router to build and maintain a picture of the network is the Routing
Information Protocol (RIP). Using RIP, routers periodically update one another and check for
changes to add to the routing table.
The DG824M gateway supports both the older RIP-1 and the newer RIP-2 protocols. Among other
improvements, RIP-2 supports subnet and multicast protocols. RIP is not required for most home
applications.
IP Addresses and the Internet
Because TCP/IP networks are interconnected across the world, every machine on the Internet must
have a unique address to make sure that transmitted data reaches the correct destination. Blocks of
addresses are assigned to organizations by the Internet Assigned Numbers Authority (IANA).
Individual users and small organizations may obtain their addresses either from the IANA or from
an Internet service provider (ISP). You can contact IANA at www.iana.org.
The Internet Protocol (IP) uses a 32-bit address structure. The address is usually written in dot
notation (also called dotted-decimal notation), in which each group of eight bits is written in
decimal form, separated by decimal points.
For example, the following binary address:
11000011 00100010 00001100 00000111
is normally written as:
195.34.12.7
B-2
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The latter version is easier to remember and easier to enter into your computer.
In addition, the 32 bits of the address are subdivided into two parts. The first part of the address
identifies the network, and the second part identifies the host node or station on the network. The
dividing point may vary depending on the address range and the application.
There are five standard classes of IP addresses. These address classes have different ways of
determining the network and host sections of the address, allowing for different numbers of hosts
on a network. Each address type begins with a unique bit pattern, which is used by the TCP/IP
software to identify the address class. After the address class has been determined, the software
can correctly identify the host section of the address. The follow figure shows the three main
address classes, including network and host sections of the address for each address type.
Class A
Network
Class B
Node
Network
Node
Class C
Network
Node
Figure 7-1: Three Main Address Classes
The five address classes are:
•
Class A
Class A addresses can have up to 16,777,214 hosts on a single network. They use an eight-bit
network number and a 24-bit node number. Class A addresses are in this range:
1.x.x.x to 126.x.x.x.
•
Class B
Class B addresses can have up to 65,354 hosts on a network. A Class B address uses a 16-bit
network number and a 16-bit node number. Class B addresses are in this range:
128.1.x.x to 191.254.x.x.
Network and Routing Basics
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
•
•
•
Class C
Class C addresses can have 254 hosts on a network. Class C addresses use 24 bits for the
network address and eight bits for the node. They are in this range:
192.0.1.x to 223.255.254.x.
Class D
Class D addresses are used for multicasts (messages sent to many hosts). Class D addresses are
in this range:
224.0.0.0 to 239.255.255.255.
Class E
Class E addresses are for experimental use.
This addressing structure allows IP addresses to uniquely identify each physical network and each
node on each physical network.
For each unique value of the network portion of the address, the base address of the range (host
address of all zeros) is known as the network address and is not usually assigned to a host. Also,
the top address of the range (host address of all ones) is not assigned, but is used as the broadcast
address for simultaneously sending a packet to all hosts with the same network address.
Netmask
In each of the address classes previously described, the size of the two parts (network address and
host address) is implied by the class. This partitioning scheme can also be expressed by a netmask
associated with the IP address. A netmask is a 32-bit quantity that, when logically combined (using
an AND operator) with an IP address, yields the network address. For instance, the netmasks for
Class A, B, and C addresses are 255.0.0.0, 255.255.0.0, and 255.255.255.0, respectively.
For example, the address 192.168.170.237 is a Class C IP address whose network portion is the
upper 24 bits. When combined (using an AND operator) with the Class C netmask, as shown here,
only the network portion of the address remains:
11000000 10101000 10101010 11101101 (192.168.170.237)
combined with:
11111111 11111111 11111111 00000000 (255.255.255.0)
Equals:
11000000 10101000 10101010 00000000 (192.168.170.0)
B-4
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
As a shorter alternative to dotted-decimal notation, the netmask may also be expressed in terms of
the number of ones from the left. This number is appended to the IP address, following a backward
slash ( / ), as “/n.” In the example, the address could be written as 192.168.170.237/24, indicating
that the netmask is 24 ones followed by 8 zeros.
Subnet Addressing
By looking at the addressing structures, you can see that even with a Class C address, there are a
large number of hosts per network. Such a structure is an inefficient use of addresses if each end of
a routed link requires a different network number. It is unlikely that the smaller office LANs would
have that many devices. You can resolve this problem by using a technique known as subnet
addressing.
Subnet addressing allows us to split one IP network address into smaller multiple physical
networks known as subnetworks. Some of the node numbers are used as a subnet number instead.
A Class B address gives us 16 bits of node numbers translating to 64,000 nodes. Most
organizations do not use 64,000 nodes, so there are free bits that can be reassigned. Subnet
addressing makes use of those bits that are free, as shown below.
Class B
Network
Subnet
Node
Figure 7-2: Example of Subnetting a Class B Address
A Class B address can be effectively translated into multiple Class C addresses. For example, the
IP address of 172.16.0.0 is assigned, but node addresses are limited to 255 maximum, allowing
eight extra bits to use as a subnet address. The IP address of 172.16.97.235 would be interpreted as
IP network address 172.16, subnet number 97, and node number 235. In addition to extending
the number of addresses available, subnet addressing provides other benefits. Subnet addressing
allows a network manager to construct an address scheme for the network by using different
subnets for other geographical locations in the network or for other departments in the
organization.
Network and Routing Basics
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Although the preceding example uses the entire third octet for a subnet address, note that you are
not restricted to octet boundaries in subnetting. To create more network numbers, you need only
shift some bits from the host address to the network address. For instance, to partition a Class C
network number (192.68.135.0) into two, you shift one bit from the host address to the network
address. The new netmask (or subnet mask) is 255.255.255.128. The first subnet has network
number 192.68.135.0 with hosts 192.68.135.1 to 129.68.135.126, and the second subnet has
network number 192.68.135.128 with hosts 192.68.135.129 to 192.68.135.254.
Note: The number 192.68.135.127 is not assigned because it is the broadcast address
of the first subnet. The number 192.68.135.128 is not assigned because it is the network
address of the second subnet.
The following table lists the additional subnet mask bits in dotted-decimal notation. To use the
table, write down the original class netmask and replace the 0 value octets with the dotted-decimal
value of the additional subnet bits. For example, to partition your Class C network with subnet
mask 255.255.255.0 into 16 subnets (4 bits), the new subnet mask becomes 255.255.255.240.
Table 7-1.
Netmask Notation Translation Table for One Octet
Dotted-Decimal Value
Number of Bits
1
2
3
4
5
6
7
8
128
192
224
240
248
252
254
255
The following table displays several common netmask values in both the dotted-decimal and the
masklength formats.
Table 7-2.
Netmask Formats
Masklength
Dotted-Decimal
255.0.0.0
/8
255.255.0.0
/16
B-6
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Table 7-2.
Netmask Formats
255.255.255.0
/24
/25
/26
/27
/28
/29
/30
/31
/32
255.255.255.128
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
255.255.255.252
255.255.255.254
255.255.255.255
NETGEAR strongly recommends that you configure all hosts on a LAN segment to use the same
netmask for the following reasons:
•
So that hosts recognize local IP broadcast packets
When a device broadcasts to its segment neighbors, it uses a destination address of the local
network address with all ones for the host address. In order for this scheme to work, all devices
on the segment must agree on which bits comprise the host address.
•
So that a local router or bridge recognizes which addresses are local and which are remote
Private IP Addresses
If your local network is isolated from the Internet (for example, when using NAT), you can assign
any IP addresses to the hosts without problems. However, the IANA has reserved the following
three blocks of IP addresses specifically for private networks:
10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255
NETGEAR recommends that you choose your private network number from this range. The
DHCP server of the DG824M gateway is preconfigured to automatically assign private addresses.
Regardless of your particular situation, do not create an arbitrary IP address; always follow the
guidelines explained here. For more information about address assignment, refer to RFC 1597,
Address Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP
Address Space. The Internet Engineering Task Force (IETF) publishes RFCs on its Web site at
www.ietf.org.
Network and Routing Basics
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Single IP Address Operation Using NAT
In the past, if multiple PCs on a LAN needed to access the Internet simultaneously, you had to
obtain a range of IP addresses from the ISP. This type of Internet account is more costly than a
single-address account typically used by a single user with a modem, rather than a router. The
DG824M gateway employs an address-sharing method called Network Address Translation
(NAT). This method allows several networked PCs to share an Internet account using only a single
IP address, which may be statically or dynamically assigned by your ISP.
The router accomplishes this address sharing by translating the internal LAN IP addresses to a
single address that is globally unique on the Internet. The internal LAN IP addresses can be either
private addresses or registered addresses. For more information about IP address translation, refer
to RFC 1631, The IP Network Address Translator (NAT).
The following figure illustrates a single IP address operation.
Private IP addresses
assigned by user
IP addresses
assigned by ISP
192.168.0.2
192.168.0.3
192.168.0.1
172.21.15.105
Internet
192.168.0.4
192.168.0.5
Figure 7-3: Single IP Address Operation Using NAT
B-8
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
This scheme offers the additional benefit of firewall-like protection because the internal LAN
addresses are not available to the Internet through the translated connection. All incoming
inquiries are filtered out by the router. This filtering can prevent intruders from probing your
system. However, using port forwarding, you can allow one PC (for example, a Web server) on
your local network to be accessible to outside users.
MAC Addresses and Address Resolution Protocol
An IP address alone cannot be used to deliver data from one LAN device to another. To send data
between LAN devices, you must convert the IP address of the destination device to its media
access control (MAC) address. Each device on an Ethernet network has a unique MAC address,
which is a 48-bit number assigned to each device by the manufacturer. The technique that
associates the IP address with a MAC address is known as address resolution. Internet Protocol
uses the Address Resolution Protocol (ARP) to resolve MAC addresses.
If a device sends data to another station on the network and the destination MAC address is not yet
recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network
receive and read the request. The destination IP address for the chosen station is included as part of
the message so that only the station with this IP address responds to the ARP request. All other
stations discard the request.
Related Documents
The station with the correct IP address responds with its own MAC address directly to the sending
device. The receiving station provides the transmitting station with the required destination MAC
address. The IP address data and MAC address data for each station are held in an ARP table. The
next time data is sent, the address can be obtained from the address information in the table.
For more information about address assignment, refer to the IETF documents RFC 1597, Address
Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP Address Space.
For more information about IP address translation, refer to RFC 1631, The IP Network Address
Translator (NAT).
Network and Routing Basics
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Domain Name Server
Many of the resources on the Internet can be addressed by simple descriptive names such as
www.NETGEAR.com. This addressing is very helpful at the application level, but the descriptive
name must be translated to an IP address in order for a user to actually contact the resource. Just as
a telephone directory maps names to phone numbers, or as an ARP table maps IP addresses to
MAC addresses, a domain name system (DNS) server maps descriptive names of network
resources to IP addresses.
When a PC accesses a resource by its descriptive name, it first contacts a DNS server to obtain the
IP address of the resource. The PC sends the desired message using the IP address. Many large
organizations, such as ISPs, maintain their own DNS servers and allow their customers to use the
servers to look up addresses.
IP Configuration by DHCP
When an IP-based local area network is installed, each PC must be configured with an IP address.
If the PCs need to access the Internet, they should also be configured with a gateway address and
one or more DNS server addresses. As an alternative to manual configuration, there is a method by
which each PC on the network can automatically obtain this configuration information. A device
on the network may act as a Dynamic Host Configuration Protocol (DHCP) server. The DHCP
server stores a list or pool of IP addresses, along with other information (such as gateway and DNS
addresses) that it may assign to the other devices on the network. The DG824M gateway has the
capacity to act as a DHCP server.
The DG824M gateway also functions as a DHCP client when connecting to the ISP. The gateway
can automatically obtain an IP address, subnet mask, DNS server addresses, and a gateway address
if the ISP provides this information by DHCP.
B-10
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Ethernet Cabling
Although Ethernet networks originally used thick or thin coaxial cable, most installations currently
use unshielded twisted pair (UTP) cabling. The UTP cable contains eight conductors, arranged in
four twisted pairs, and terminated with an RJ45 type connector. A normal "straight-through" UTP
Ethernet cable follows the EIA568B standard wiring as described in Table 7-1.
Table 7-1.
UTP Ethernet cable wiring, straight-through
Signal
Pin
Wire color
Orange/White
1
2
3
4
5
6
7
8
Transmit (Tx) +
Transmit (Tx) -
Receive (Rx) +
Orange
Green/White
Blue
Blue/White
Green
Receive (Rx) -
Brown/White
Brown
Uplink Switches and Crossover Cables
In the wiring table, the concept of transmit and receive are from the perspective of the PC. For
example, the PC transmits on pins 1 and 2. At the hub, the perspective is reversed, and the hub
receives on pins 1 and 2. When connecting a PC to a PC, or a hub port to another hub port, the
transmit pair must be exchanged with the receive pair. This exchange is done by one of two
mechanisms. Most hubs provide an Uplink switch which will exchange the pairs on one port,
allowing that port to be connected to another hub using a normal Ethernet cable. The second
method is to use a crossover cable, which is a special cable in which the transmit and receive pairs
are exchanged at one of the two cable connectors. Crossover cables are often unmarked as such,
and must be identified by comparing the two connectors. Since the cable connectors are clear
plastic, it is easy to place them side by side and view the order of the wire colors on each. On a
straight-through cable, the color order will be the same on both connectors. On a crossover cable,
the orange and blue pairs will be exchanged from one connector to the other.
Network and Routing Basics
B-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Cable Quality
A twisted pair Ethernet network operating at 10 Mbits/second (10BASE-T) will often tolerate low
quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be rated as Category 5, or
"Cat 5", by the Electronic Industry Association (EIA). This rating will be printed on the cable
jacket. A Category 5 cable will meet specified requirements regarding loss and crosstalk. In
addition, there are restrictions on maximum cable length for both 10 and 100 Mbits/second
networks.
Internet Security and Firewalls
When your LAN connects to the Internet through a router, an opportunity is created for outsiders
to access or disrupt your network. A NAT router provides some protection because by the very
nature of the Network Address Translation (NAT) process, the network behind the NAT router is
shielded from access by outsiders on the Internet. However, there are methods by which a
determined hacker can possibly obtain information about your network or at the least can disrupt
your Internet access. A greater degree of protection is provided by a firewall router.
What is a Firewall?
A firewall is a device that protects one network from another, while allowing communication
between the two. A firewall incorporates the functions of the NAT router, while adding features for
dealing with a hacker intrusion or attack. Several known types of intrusion or attack can be
recognized when they occur. When an incident is detected, the firewall can log details of the
attempt, and can optionally send email to an administrator notifying them of the incident. Using
information from the log, the administrator can take action with the ISP of the hacker. In some
types of intrusions, the firewall can fend off the hacker by discarding all further packets from the
hacker’s IP address for a period of time.
B-12
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Stateful Packet Inspection
Unlike simple Internet sharing routers, a firewall uses a process called stateful packet inspection to
ensure secure firewall filtering to protect your network from attacks and intrusions. Since
user-level applications such as FTP and Web browsers can create complex patterns of network
traffic, it is necessary for the firewall to analyze groups of network connection "states." Using
Stateful Packet Inspection, an incoming packet is intercepted at the network layer and then
analyzed for state-related information associated with all network connections. A central cache
within the firewall keeps track of the state information associated with all network connections.
All traffic passing through the firewall is analyzed against the state of these connections in order to
determine whether or not it will be allowed to pass through or rejected.
Denial of Service Attack
A hacker may be able to prevent your network from operating or communicating by launching a
Denial of Service (DoS) attack. The method used for such an attack can be as simple as merely
flooding your site with more requests than it can handle. A more sophisticated attack may attempt
to exploit some weakness in the operating system used by your router or gateway. Some operating
systems can be disrupted by simply sending a packet with incorrect length information.
Wireless Networking
The DG824M gateway conforms to the Institute of Electrical and Electronics Engineers (IEEE)
802.11b standard for wireless LANs (WLANs). On an 802.11b wireless link, data is encoded using
direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio
spectrum at 2.5GHz. The maximum data rate for the wireless link is 11 Mbps, but it will
automatically back down from 11 Mbps to 5.5, 2, and 1 Mbps when the radio signal is weak or
when interference is detected.
The 802.11b standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting
interoperability among 802.11b devices.
Wireless Network Configuration
The 802.11b standard offers two methods for configuring a wireless network - ad hoc and
infrastructure.
Network and Routing Basics
B-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Ad Hoc Mode (Peer-to-Peer Workgroup)
In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed
points to the network - each node can generally communicate with any other node. There is no
Access Point involved in this configuration. This mode enables you to quickly set up a small
wireless workgroup and allows workgroup members to exchange data or share printers as
supported by Microsoft Networking in the various Windows operating systems. Some vendors
also refer to ad hoc networking as Peer-to-Peer group networking.
In this configuration, network packets are directly sent and received by the intended transmitting
and receiving stations. As long as the stations are within range of one another, this is the easiest
and least expensive way to set up a wireless network.
Infrastructure Mode
With a wireless Access Point, you can operate the wireless LAN in the infrastructure mode. This
mode provides wireless connectivity to multiple wireless network devices within a fixed range or
area of coverage, interacting with wireless nodes via an antenna.
In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet
data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple Access
Points via a wired Ethernet backbone can further extend the wireless network coverage. As a
mobile computing device moves out of the range of one access point, it moves into the range of
another. As a result, wireless clients can freely roam from one Access Point domain to another and
still maintain seamless network connection.
Extended Service Set Identification (ESSID)
The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification
(SSID). In an ad-hoc wireless network with no access points, the Basic Service Set Identification
(BSSID) is used. In an infrastructure wireless network that includes an access point, the Extended
Service Set Identification (ESSID) is used, but may still be referred to as SSID.
An SSID is a thirty-two character (maximum) alphanumeric key identifying the wireless local area
network. Some vendors refer to the SSID as network name. For the wireless devices in a network
to communicate with each other, all devices must be configured with the same SSID.
B-14
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Authentication and WEP Encryption
The absence of a physical connection between nodes makes the wireless links vulnerable to
eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11
standard has defined two types of authentication methods, Open System and Shared Key. With
Open System authentication, a wireless PC can join any network and receive any messages that are
not encrypted. With Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an
Open System network.
Wired Equivalent Privacy (WEP) data encryption is utilized when the wireless nodes or access
points are configured to operate in Shared Key authentication mode. There are two shared key
methods implemented in most commercially available products, 64-bit and 128-bit WEP data
encryption.
The 64-bit WEP data encryption method, allows for a five-character (40-bit) input. Additionally,
24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. (The 24
factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all
data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption
as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits
wide.
The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the
forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user
configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal
characters to ease encryption key entry.
Wireless Channel Selection
IEEE 802.11 wireless nodes communicate with each other using radio frequency signals in the
ISM (Industrial, Scientific, and Medical) band between 2.4Ghz and 2.5Ghz. Neighboring channels
are 5Mhz apart. However, due to spread spectrum effect of the signals, a node sending signals
using a particular channel will utilize frequency spectrum12.5Mhz above and below the center
channel frequency. As a result, two separate wireless networks using neighboring channels (for
example, channel 1 and channel 2) in the same general vicinity will interfere with each other.
Applying two channels that allow the maximum channel separation will decrease the amount of
channel cross-talk, and provide a noticeable performance increase over networks with minimal
channel separation.
Network and Routing Basics
B-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
The radio frequency channels used are listed in Table 7-2:
Table 7-2.
802.11 Radio Frequency Channels
Channel
Center Frequency
Frequency Spread
1
2412Mhz
2417Mhz
2422Mhz
2427Mhz
2432Mhz
2437Mhz
2442Mhz
2447Mhz
2452Mhz
2457Mhz
2462Mhz
2467Mhz
2472Mhz
2399.5Mhz - 2424.5Mhz
2404.5Mhz - 2429.5Mhz
2409.5Mhz - 2434.5Mhz
2414.5Mhz - 2439.5Mhz
2419.5Mhz - 2444.5Mhz
2424.5Mhz - 2449.5Mhz
2429.5Mhz - 2454.5Mhz
2434.5Mhz - 2459.5Mhz
2439.5Mhz - 2464.5Mhz
2444.5Mhz - 2469.5Mhz
2449.5Mhz - 2474.5Mhz
2454.5Mhz - 2479.5Mhz
2459.5Mhz - 2484.5Mhz
2
3
4
5
6
7
8
9
10
11
12
13
Note: The available channels supported by the wireless products in various countries are different.
The preferred channel separation between the channels in neighboring wireless networks is 25
MHz (5 channels). This means that you can apply up to three different channels within your
wireless network. There are only 11 usable wireless channels in the United States. It is
recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as
these three channels do not overlap.
B-16
Network and Routing Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Preparing Your Network
This appendix describes how to prepare your network to connect to the Internet through the Model
RP614 Web Safe Router and how to verify the readiness of broadband Internet service from an
Internet service provider (ISP).
Note: If an ISP technician configured your computer during the installation of a
broadband modem, or if you configured it using instructions provided by your ISP, you
may need to copy the current configuration information for use in the configuration of
your firewall. Write down this information before reconfiguring your computers. Refer
to “Obtaining ISP Configuration Information for Windows Computers” on page C-19 or
“Obtaining ISP Configuration Information for Macintosh Computers” on page C-20 for
further information.
Preparing Your Computers for TCP/IP Networking
Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/
Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its
networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/
IP is probably already installed as well.
Most operating systems include the software components you need for networking with TCP/IP:
•
•
Windows® 95 or later includes the software components for establishing a TCP/IP network.
Windows 3.1 does not include a TCP/IP component. You need to purchase a third-party TCP/
IP application package such as NetManage Chameleon.
•
Macintosh Operating System 7 or later includes the software components for establishing a
TCP/IP network.
Preparing Your Network
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
•
All versions of UNIX or Linux include TCP/IP components. Follow the instructions provided
with your operating system or networking software to install TCP/IP on your computer.
In your IP network, each PC and the firewall must be assigned a unique IP addresses. Each PC
must also have certain other IP configuration information such as a subnet mask (netmask), a
domain name server (DNS) address, and a default gateway address. In most cases, you should
install TCP/IP so that the PC obtains its specific network configuration information automatically
from a DHCP server during bootup. For a detailed explanation of the meaning and purpose of
these configuration items, refer to “Appendix B, “Networks, Routing, and Firewall Basics.”
The RP614 router is shipped preconfigured as a DHCP server. The firewall assigns the following
TCP/IP configuration information automatically when the PCs are rebooted:
•
•
•
PC or workstation IP addresses—192.168.0.2 through 192.168.0.254
Subnet mask—255.255.255.0
Gateway address (the firewall)—192.168.0.1
These addresses are part of the IETF-designated private address range for use in private networks.
Configuring Windows 95, 98, and Me for TCP/IP Networking
As part of the PC preparation process, you need to manually install and configure TCP/IP on each
networked PC. Before starting, locate your Windows CD; you may need to insert it during the
TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components:
C-2
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
You must have an Ethernet adapter, the TCP/IP protocol, and Client for Microsoft Networks.
Note: It is not necessary to remove any other network components shown in the
Network window in order to install the adapter, TCP/IP, or Client for Microsoft
Networks.
If you need to install a new adapter, follow these steps:
a. Click the Add button.
b. Select Adapter, and then click Add.
c. Select the manufacturer and model of your Ethernet adapter, and then click OK.
If you need TCP/IP:
a. Click the Add button.
b. Select Protocol, and then click Add.
c. Select Microsoft.
d. Select TCP/IP, and then click OK.
Preparing Your Network
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
If you need Client for Microsoft Networks:
a. Click the Add button.
b. Select Client, and then click Add.
c. Select Microsoft.
d. Select Client for Microsoft Networks, and then click OK.
3. Restart your PC for the changes to take effect.
Enabling DHCP to Automatically Configure TCP/IP Settings in
Windows 95B, 98, and Me
After the TCP/IP protocol components are installed, each PC must be assigned specific
information about itself and resources that are available on its network. The simplest way to
configure this information is to allow the PC to obtain the information from a DHCP server in the
network.
You will find there are many similarities in the procedures for different Windows systems
when using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these
versions of Windows.
Locate your Network Neighborhood icon.
•
If the Network Neighborhood icon is on the Windows desktop, position your mouse
pointer over it and right-click your mouse button.
•
If the icon is not on the desktop,
•
•
•
Click Start on the task bar located at the bottom left of the window.
Choose Settings, and then Control Panel.
Locate the Network Neighborhood icon and click on it. This will open the Network
panel as shown below.
C-4
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
Verify the following settings as shown:
•
•
•
•
Client for Microsoft Network exists
Ethernet adapter is present
TCP/IP is present
Primary Network Logon is set to
Windows logon
Click on the Properties button. The
following TCP/IP Properties window will
display.
Preparing Your Network
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• By default, the IP Address tab is open on
this window.
• Verify the following:
Obtain an IP address automatically is
selected. If not selected, click in the radio
button to the left of it to select it. This
setting is required to enable the DHCP server
to automatically assign an IP address.
• Click OK to continue.
Restart the PC.
Repeat these steps for each PC with this
version of Windows on your network.
Selecting Windows’ Internet Access Method
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Internet Options icon.
3. Select “I want to set up my Internet connection manually” or “I want to connect through a
Local Area Network” and click Next.
4. Select “I want to connect through a Local Area Network” and click Next.
5. Uncheck all boxes in the LAN Internet Configuration screen and click Next.
6. Proceed to the end of the Wizard.
Verifying TCP/IP Properties
After your PC is configured and has rebooted, you can check the TCP/IP configuration using the
utility winipcfg.exe:
1. On the Windows taskbar, click the Start button, and then click Run.
C-6
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
2. Type winipcfg, and then click OK.
The IP Configuration window opens, which lists (among other things), your IP address, subnet
mask, and default gateway.
3. From the drop-down box, select your Ethernet adapter.
The window is updated to show your settings, which should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
•
•
•
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
The default gateway is 192.168.0.1
Configuring Windows NT4, 2000 or XP for IP Networking
As part of the PC preparation process, you may need to install and configure
TCP/IP on each networked PC. Before starting, locate your Windows CD; you may need to insert
it during the TCP/IP installation process.
Install or Verify Windows Networking Components
To install or verify the necessary components for IP networking:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dialup Connections icon.
3. If an Ethernet adapter is present in your PC, you should see an entry for Local Area
Connection. Double-click that entry.
4. Select Properties.
5. Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6. Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7. Click OK and close all Network and Dialup Connections windows.
8. Then, restart your PC.
Preparing Your Network
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4
You will find there are many similarities in the procedures for different Windows systems when
using DHCP to configure TCP/IP.
The following steps will walk you through the configuration process for each of these versions of
Windows.
DHCP Configuration of TCP/IP in Windows XP
Locate your Network Neighborhood icon.
•
•
Select Control Panel from the Windows XP new Start Menu.
Select the Network Connections icon on the Control Panel. This will take you to the next
step.
• Now the Network Connection window
displays.
The Connections List that shows all the
network connections set up on the PC,
located to the right of the window.
• Right-click on the Connection you will
use and choose Status.
C-8
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• Now you should be at the Local Area
Network Connection Status window. This
box displays the connection status, duration,
speed, and activity statistics.
• Administrator logon access rights are needed
to use this window.
• Click the Properties button to view details
about the connection.
• The TCP/IP details are presented on the
Support tab page.
• Select Internet Protocol, and click
Properties to view the configuration
information.
Preparing Your Network
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• Verify that the Obtain an IP address
automatically radio button is selected.
• Verify that Obtain DNS server address
automatically radio button is selected.
• Click the OK button.
This completes the DHCP configuration of TCP/
IP in Windows XP.
Repeat these steps for each PC with this version
of Windows on your network.
DHCP Configuration of TCP/IP in Windows 2000
Once again, after you have installed the network card, TCP/IP for Windows 2000 is configured.
TCP/IP should be added by default and set to DHCP without your having to configure it.
However, if there are problems, follow these steps to configure TCP/IP with DHCP for Windows
2000.
C-10
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• Click on the My Network Places icon on the Windows desktop. This will bring up a window
called Network and Dial-up Connections.
• Right click on Local Area Connection and select Properties.
• The Local Area Connection Properties
dialog box appears.
• Verify that you have the correct Ethernet
card selected in the Connect using: box.
• Verify that at least the following two items
are displayed and selected in the box of
“Components checked are used by this
connection:”
•
•
Client for Microsoft Networks and
Internet Protocol (TCP/IP)
• Click OK.
Preparing Your Network
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• With Internet Protocol (TCP/IP) selected,
click on Properties to open the Internet
Protocol (TCP/IP) Properties dialogue box.
• Verify that
•
Obtain an IP address automatically is
selected.
•
Obtain DNS server address
automatically is selected.
• Click OK to return to Local Area
Connection Properties.
• Click OK again to complete the
configuration process for Windows 2000.
Restart the PC.
Repeat these steps for each PC with this version
of Windows on your network.
C-12
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
DHCP Configuration of TCP/IP in Windows NT4
Once you have installed the network card, you need to configure the TCP/IP environment for
Windows NT 4.0. Follow this procedure to configure TCP/IP with DHCP in Windows NT 4.0.
• Choose Settings from the Start Menu, and then select Control Panel.
This will display Control Panel window.
• Double-click the Network icon in the
Control Panel window.
The Network panel will display.
• Select the Protocols tab to continue.
Preparing Your Network
C-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• Highlight the TCP/IP Protocol in the
Network Protocols box, and click on the
Properties button.
C-14
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
• The TCP/IP Properties dialog box now
displays.
• Click the IP Address tab.
• Select the radio button marked Obtain an IP
address from a DHCP server.
• Click OK. This completes the configuration
of TCP/IP in Windows NT.
Restart the PC.
Repeat these steps for each PC with this version
of Windows on your network.
Verifying TCP/IP Properties for Windows XP, 2000, and NT4
To check your PC’s TCP/IP configuration:
1. On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2. Type cmdand then click OK.
A command window opens
3. Type ipconfig /all
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
•
•
The IP address is between 192.168.0.2 and 192.168.0.254
The subnet mask is 255.255.255.0
Preparing Your Network
C-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
•
The default gateway is 192.168.0.1
4. Type exit
Configuring the Macintosh for TCP/IP Networking
Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On
each networked Macintosh, you will need to configure TCP/IP to use DHCP.
MacOS 8.6 or 9.x
1. From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens:
2. From the “Connect via” box, select your Macintosh’s Ethernet interface.
3. From the “Configure” box, select Using DHCP Server.
You can leave the DHCP Client ID box empty.
4. Close the TCP/IP Control Panel.
5. Repeat this for each Macintosh on your network.
MacOS X
1. From the Apple menu, choose System Preferences, then Network.
C-16
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
2. If not already selected, select Built-in Ethernet in the Configure list.
3. If not already selected, Select Using DHCP in the TCP/IP tab.
4. Click Save.
Verifying TCP/IP Properties for Macintosh Computers
After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by
returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
The panel is updated to show your settings, which should match the values below if you are using
the default TCP/IP settings that NETGEAR recommends:
•
•
•
The IP Address is between 192.168.0.2 and 192.168.0.254
The Subnet mask is 255.255.255.0
The Router address is 192.168.0.1
If you do not see these values, you may need to restart your Macintosh or you may need to switch
the “Configure” setting to a different option, then back again to “Using DHCP Server”.
Preparing Your Network
C-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
Verifying the Readiness of Your Internet Account
For broadband access to the Internet, you need to contract with an Internet service provider (ISP)
for a single-user Internet access account using a cable modem or DSL modem. This modem must
be a separate physical box (not a card) and must provide an Ethernet port intended for connection
to a Network Interface Card (NIC) in a computer. Your firewall does not support a USB-connected
broadband modem.
For a single-user Internet account, your ISP supplies TCP/IP configuration information for one
computer. With a typical account, much of the configuration information is dynamically assigned
when your PC is first booted up while connected to the ISP, and you will not need to know that
dynamic information.
In order to share the Internet connection among several computers, your firewall takes the place of
the single PC, and you need to configure it with the TCP/IP information that the single PC would
normally use. When the firewall’s Internet port is connected to the broadband modem, the firewall
appears to be a single PC to the ISP. The firewall then allows the PCs on the local network to
masquerade as the single PC to access the Internet through the broadband modem. The method
used by the firewall to accomplish this is called Network Address Translation (NAT) or IP
masquerading.
Are Login Protocols Used?
Some ISPs require a special login protocol, in which you must enter a login name and password in
order to access the Internet. If you normally log in to your Internet account by running a program
such as WinPOET or EnterNet, then your account uses PPP over Ethernet (PPPoE).
When you configure your router, you will need to enter your login name and password in the
router’s configuration menus. After your network and firewall are configured, the firewall will
perform the login task when needed, and you will no longer need to run the login program from
your PC. It is not necessary to uninstall the login program.
What Is Your Configuration Information?
More and more, ISPs are dynamically assigning configuration information. However, if your ISP
does not dynamically assign configuration information but instead used fixed configurations, your
ISP should have given you the following basic information for your account:
C-18
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
•
•
•
•
An IP address and subnet mask
A gateway IP address, which is the address of the ISP’s router
One or more domain name server (DNS) IP addresses
Host name and domain suffix
For example, your account’s full server names may look like this:
mail.xxx.yyy.com
In this example, the domain suffix is xxx.yyy.com.
If any of these items are dynamically supplied by the ISP, your firewall automatically acquires
them.
If an ISP technician configured your PC during the installation of the broadband modem, or if you
configured it using instructions provided by your ISP, you need to copy the configuration
information from your PC’s Network TCP/IP Properties window or Macintosh TCP/IP Control
Panel before reconfiguring your PC for use with the firewall. These procedures are described next.
Obtaining ISP Configuration Information for Windows Computers
As mentioned above, you may need to collect configuration information from your PC so that you
can use this information when you configure the RP614 router. Following this procedure is only
necessary when your ISP does not dynamically supply the account information.
To get the information you need to configure the firewall for Internet access:
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network icon.
The Network window opens, which displays a list of installed components.
3. Select TCP/IP, and then click Properties.
The TCP/IP Properties dialog box opens.
4. Select the IP Address tab.
If an IP address and subnet mask are shown, write down the information. If an address is
present, your account uses a fixed (static) IP address. If no address is present, your account
uses a dynamically-assigned IP address. Click “Obtain an IP address automatically”.
5. Select the Gateway tab.
Preparing Your Network
C-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
If an IP address appears under Installed Gateways, write down the address. This is the ISP’s
gateway address. Select the address and then click Remove to remove the gateway address.
6. Select the DNS Configuration tab.
If any DNS server addresses are shown, write down the addresses. If any information appears
in the Host or Domain information box, write it down. Click Disable DNS.
7. Click OK to save your changes and close the TCP/IP Properties dialog box.
You are returned to the Network window.
8. Click OK.
9. Reboot your PC at the prompt. You may also be prompted to insert your Windows CD.
Obtaining ISP Configuration Information for Macintosh
Computers
As mentioned above, you may need to collect configuration information from your Macintosh so
that you can use this information when you configure the RP614 router. Following this procedure
is only necessary when your ISP does not dynamically supply the account information.
To get the information you need to configure the firewall for Internet access:
1. From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens, which displays a list of configuration settings. If the
“Configure” setting is “Using DHCP Server”, your account uses a dynamically-assigned IP
address. In this case, close the Control Panel and skip the rest of this section.
2. If an IP address and subnet mask are shown, write down the information.
3. If an IP address appears under Router address, write down the address. This is the ISP’s
gateway address.
4. If any Name Server addresses are shown, write down the addresses. These are your ISP’s DNS
addresses.
5. If any information appears in the Search domains information box, write it down.
6. Change the “Configure” setting to “Using DHCP Server”.
7. Close the TCP/IP Control Panel.
C-20
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
Restarting the Network
Once you’ve set up your computers to work with the firewall, you must reset the network for the
devices to be able to communicate correctly. Restart any computer that is connected to the firewall.
After configuring all of your computers for TCP/IP networking and restarting them, and
connecting them to the local network of your RP614 router, you are ready to access and configure
the firewall.
Preparing Your Network
C-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model RP614 Web Safe Router
C-22
Preparing Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
10BASE-T
100BASE-Tx
802.11b
IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.
IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.
IEEE specification for wireless networking at 11 Mbps using direct-sequence
spread-spectrum (DSSS) technology and operating in the unlicensed radio
spectrum at 2.5GHz.
ADSL
See Asymmetric Digital Subscriber Line
Asymmetric Digital
Subscriber Line
A technology for sending data over regular telephone lines. ADSL allows data
rates up to 8 Mbps downstream and 640 Kbps upstream.
Denial of Service
attack
DoS. A hacker attack designed to prevent your computer or network from
operating or communicating.
DHCP
See Dynamic Host Configuration Protocol.
DNS
See Domain Name Server.
Domain Name
A descriptive name for an address or group of addresses on the Internet.
Domain names are of the form of a registered entity name plus one of a
number of predefined top level suffixes such as .com, .edu, .uk, etc. For
example, in the address mail.NETGEAR.com, mail is a server name and
NETGEAR.com is the domain.
Domain Name Server
DSLAM
A Domain Name Server (DNS) resolves descriptive names of network
resources (such as www.NETGEAR.com) to numeric IP addresses.
DSL Access Multiplexor. The piece of equipment at the telephone company
central office that provides the ADSL signal.
Glossary
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
Dynamic Host
Configuration
Protocol
DHCP. An Ethernet protocol specifying how a centralized DHCP server can
assign network configuration information to multiple DHCP clients. The
assigned information includes IP addresses, DNS addresses, and gateway
(router) addresses.
Gateway
A local device, usually a router, that connects hosts on a local network to other
networks.
IP
See Internet Protocol.
IP Address
A four-byte number uniquely defining each host on the Internet. Ranges of
addresses are assigned by Internic, an organization formed for this purpose.
Usually written in dotted-decimal notation with periods separating the bytes
(for example, 134.177.244.57).
IPSec
Internet Protocol Security. IPSec is a series of guidelines for securing private
information transmitted over public networks. IPSec is a VPN method
providing a higher level of security than PPTP.
ISP
Internet service provider.
Internet Protocol
The main internetworking protocol used in the Internet. Used in conjunction
with the Transfer Control Protocol (TCP) to form TCP/IP.
LAN
See local area network.
local area network
LAN. A communications network serving users within a limited area, such as
one floor of a building. A LAN typically connects multiple personal
computers and shared network devices such as storage and printers. Although
many technologies exist to implement a LAN, Ethernet is the most common
for connecting personal computers.
MAC address
Media Access Control address. A unique 48-bit hardware address assigned to
every Ethernet node. Usually written in the form 01:23:45:67:89:ab.
Mbps
MSB
MTU
Megabits per second.
See Most Significant Bit or Most Significant Byte.
See Maximum Transmission Unit.
Maximum Transmit
Unit
The size in bytes of the largest packet that can be sent or received.
Most Significant Bit or
Most Significant Byte
The portion of a number, address, or field that is farthest left when written as a
single number in conventional hexadecimal ordinary notation. The part of the
number having the most value.
2
Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
NAT
See Network Address Translation.
Netmask
A number that explains which part of an IP address comprises the network
address and which part is the host address on that network. It can be
expressed in dotted-decimal notation or as a number appended to the IP
address. For example, a 28-bit mask starting from the MSB can be shown as
255.255.255.192 or as /28 appended to the IP address.
Network Address
Translation
A technique by which several hosts share a single IP address for access to the
Internet.
packet
A block of information sent over a network. A packet typically contains a
source and destination network address, some protocol and length
information, a block of data, and a checksum.
PPP
See Point-to-Point Protocol.
See PPP over ATM
PPPoA
PPPoE
See PPP over Ethernet
PPP over ATM
PPPoA. PPP over ATM is a protocol for connecting remote hosts to the
Internet over an always-on connection by simulating a dial-up connection.
PPP over Ethernet
PPTP
PPPoE. PPP over Ethernet is a protocol for connecting remote hosts to the
Internet over an always-on connection by simulating a dial-up connection.
Point-to-Point Tunneling Protocol. A method for establishing a virtual private
network (VPN) by embedding Microsoft’s network protocol into Internet
packets.
PSTN
Public Switched Telephone Network.
Point-to-Point
Protocol
PPP. A protocol allowing a computer using TCP/IP to connect directly to the
Internet.
RFC
Request For Comment. Refers to documents published by the Internet
Engineering Task Force (IETF) proposing standard protocols and procedures
for the Internet. RFCs can be found at www.ietf.org.
RIP
See Routing Information Protocol.
router
A device that forwards data between networks. An IP router forwards data
based on IP source and destination addresses.
Routing Information
Protocol
A protocol in which routers periodically exchange information with one
another so that they can determine minimum distance paths between sources
and destinations.
Glossary
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Manual for the Model DG824M Wireless ADSL Modem Gateway
subnet mask
UTP
See netmask.
Unshielded twisted pair. The cable used by 10BASE-T and 100BASE-Tx
Ethernet networks.
VCI
VPI
Virtual Channel Identifier. Together with the VPI, defines a Virtual Channel
through an ATM network. Used by ATM switching equipment to route data
through the network.
Virtual Path Identifier. Together with the VCI, defines a Virtual Channel
through an ATM network. Used by ATM switching equipment to route data
through the network.
WAN
WEP
See wide area network.
Wired Equivalent Privacy. WEP is a data encryption protocol for 802.11b
wireless networks. All wireless nodes and access points on the network are
configured with a 64-bit or 128-bit Shared Key for data encryption.
wide area network
Wi-Fi
WAN. A long distance link used to extend or connect remotely located local
area networks. The Internet is a large WAN.
See 802.11b. A trade name for the 802.11b wireless networking standard,
given by the Wireless Ethernet Compatibility Alliance (WECA, see http://
www.wi-fi.net), an industry standard group promoting interoperability among
802.11b devices.
Windows Internet
Naming Service
WINS. Windows Internet Naming Service is a server process for resolving
Windows-based computer names to IP addresses. If a remote network
contains a WINS server, your Windows PCs can gather information from that
WINS server about its local hosts. This allows your PCs to browse that remote
network using Network Neighborhood.
WINS
See Windows Internet Naming Service.
4
Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
802.11b B-13
DHCP 1-3, 6-5, B-10
A
Account Name 2-14, 2-18
ad-hoc mode B-14
DMZ Server 6-1
Auto Uplink 1-3
DNS Proxy 1-4
DNS, dynamic 6-7
B
backup configuration 5-1
domain C-20
BSSID B-14
Domain Name 2-14, 2-18
DoS attack B-13
C
Cabling B-11
Channel 3-3, B-15
E
configuration
EnterNet C-18
backup 5-1
erasing 5-3
EPROM, for firmware upgrade 1-5
ESSID 3-3, B-14
router, initial 2-1
Ethernet 1-3
content filtering 1-3
Ethernet cable B-11
conventions
typography 1-4
F
factory settings, restoring 5-3
features 1-1
firewall features 1-2
FLASH memory 5-3
front panel 1-6
D
date and time 7-9
Daylight Savings Time 4-15, 7-9
daylight savings time 4-15
Index
1
Download from Www.Somanuals.com. All Manuals Search And Download.
G
M
gateway address C-20
MAC 3-4
H
Macintosh C-19
configuring for IP networking C-16
Obtaining ISP Configuration Information C-20
I
IANA
masquerading C-18
metric 6-11
contacting B-2
IETF B-1
MTU 6-4
inbound rules 4-7
infrastructure mode B-14
installation 1-4
multicasting 6-4
N
NAT C-18
Internet account
address information C-18
establishing C-18
NAT. See Network Address Translation
NETGEAR
contacting 1-3
IP addresses C-19, C-20
netmask
translation table B-6
and the Internet B-2
auto-generated 7-3
private B-7
NTP 4-14, 7-9
translating B-9
IP configuration by DHCP B-10
O
IP networking
for Macintosh C-16
for Windows C-2, C-7
order of precedence 4-12
outbound rules 4-10
ISP 2-1
L
P
LEDs
passphrase 1-2
description 1-7
troubleshooting 7-2
Password 2-13
password
log
restoring 7-9
sending 5-13
PC, using to configure C-21
ping 6-2
Login 2-13
2
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
placement 3-1
service blocking 4-10
port filtering 4-10
port forwarding 4-7
service numbers 4-13
Setup Wizard 2-1
port numbers 4-13
SMTP 5-13
SSID 3-3, 3-4, B-14
stateful packet inspection 1-2, B-13
Static Routes 6-6
2-19
protocols
Address Resolution B-9
DHCP 1-3, B-10
Routing Information 1-3, B-2
support 1-3
subnet addressing B-5
Syslog 5-12
TCP/IP 1-3
publications, related B-1
T
TCP/IP
R
range 3-1
configuring C-1
network, troubleshooting 7-7
TCP/IP properties
requirements
hardware 2-2
technical support 1-3
time of day 7-9
reserved IP adresses 6-6
timeout, administrator login 4-2
time-stamping 4-15
troubleshooting 7-1
RFC
1466 B-7, B-9
1597 B-7, B-9
1631 B-8, B-9
finding B-7
router concepts B-1
U
Routing Information Protocol 1-3, B-2
rules
URL 4-4
inbound 4-7
outbound 4-10
USB C-18
W
S
WEP 3-6, B-15
Secondary DNS Server 2-12, 2-13, 2-14, 2-16, 2-18,
WEP (Wired Equivalent Privacy) 3-7
2-19
Index
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WEP encryption 1-2
Wi-Fi B-13
winipcfg utility C-6
WinPOET C-18
WINS 6-6
Wired Equivalent Privacy. See WEP
Wireless Ethernet B-13
World Wide Web 1-iii
4
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
|