NEC Projector NP 610 User Manual

Portable Projector  
NP610/NP510/NP410/NP405/  
NP310/NP305/NP510W/NP410W  
NP610S/NP510WS  
User’s Manual  
NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W  
NP610S/NP510WS  
The projector’s model name indicated on the projector’s label is NP610,  
NP510, NP410, NP405, NP310, NP305, NP510W, NP410W, NP610S,  
NP510WS, NP610G, NP510G, NP410G, NP405G, NP310G, NP305G,  
NP510WG, NP410WG, NP610SG, and NP510WSG respectively.  
All the models are referred to as NP610, NP510, NP410, NP405,  
NP310, NP305, NP510W, NP410W, NP610S, and NP510WS through-  
out the user’s manual except some of the specification pages.  
The NP405 and NP305 are not distributed in North America.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Safety Cautions  
Precautions  
Please read this manual carefully before using your NEC NP610, NP510, NP410, NP405, NP310, NP305, NP510W,  
NP410W, NP610S, and NP510WS projector and keep the manual handy for future reference.  
CAUTION  
To turn off main power, be sure to remove the plug from power outlet.  
The power outlet socket should be installed as near to the equipment as possible, and should be easily  
accessible.  
CAUTION  
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.  
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical  
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.  
This symbol alerts the user that important information concerning the operation and maintenance of this  
unit has been provided.  
The information should be read carefully to avoid problems.  
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.  
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS  
CAN BE FULLY INSERTED.  
DOC Compliance Notice (for Canada only)  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula-  
tions.  
Machine Noise Information Regulation - 3. GPSGV,  
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779.  
CAUTION  
Avoid displaying stationary images for a prolonged period of time.  
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.  
If this should happen, continue to use your projector. The static background from previous images will  
disappear.  
Disposing of your used product  
EU-wide legislation as implemented in each Member State requires that used electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This in-  
cludes projectors and their electrical accessories or lamps. When you dispose of such products, please  
follow the guidance of your local authority and/or ask the shop where you purchased the product.  
After collecting the used products, they are reused and recycled in a proper way. This effort will help us  
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human  
health and the environment at the minimum level.  
The mark on the electrical and electronic products only applies to the current European Union Member  
States.  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Important Information  
WARNING TO CALIFORNIA RESIDENTS:  
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California  
to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.  
RF Interference (for USA only)  
WARNING  
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those  
specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regu-  
lation could void your right to operate this equipment. This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and  
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio / TV technician for help.  
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with  
this equipment. If a power cable is not supplied with this equipment please contact your supplier.  
Important Safeguards  
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them  
carefully and heed all warnings.  
Installation  
• Do not place the projector in the following conditions:  
- on an unstable cart, stand, or table.  
- near water, baths, or damp rooms.  
- in direct sunlight, near heaters, or heat radiating appliances.  
- in a dusty, smoky or steamy environment.  
- on a sheet of paper or cloth, rugs or carpets.  
• If you wish to have the projector installed on the ceiling:  
- Do not attempt to install the projector yourself.  
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk  
of bodily injury.  
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance  
with any local building codes.  
- Please consult your dealer for more information.  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
WARNING  
• Do not cover the lens with the lens cap or equivalent while the projector is on. Doing so can lead to melting of  
the cap due to the heat emitted from the light output.  
• Do not place any objects, which are easily affected by heat, in front of the projector lens. Doing so could lead  
to the object melting from the heat that is emitted from the light output.  
Place the projector in a horizontal position  
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other  
than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.  
10°  
Fire and Shock Precautions  
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your  
projector. Allow at least 4 inches (10cm) of space between your projector and a wall.  
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while  
the projector is turned on and immediately after the projector is turned off.  
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve  
any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your  
projector. If something should fall into your projector, disconnect it immediately and have the object removed by a  
qualified service personnel.  
• Do not place any objects on top of the projector.  
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.  
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz (NP610/NP510/NP410/NP405/  
NP310/NP305/NP510W/NP410W/NP610S/NP510WS) or 200-240V AC 50/60 Hz (NP610G/NP510G/NP410G/  
NP405G/NP310G/NP305G/NP510WG/ NP410WG/NP610SG/NP510WSG). Ensure that your power supply fits this  
requirement before attempting to use your projector.  
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.  
• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the  
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause  
unpredictable outcome such as fire or injury to the eyes.  
• Do not place any objects, which are easily affected by heat, in front of a projector exhaust vent.  
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the ex-  
haust.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.  
- Do not use any power cables than the supplied one.  
- Do not bend or tug the power cable excessively.  
- Do not place the power cable under the projector, or any heavy object.  
- Do not cover the power cable with other soft materials such as rugs.  
- Do not heat the power cable.  
- Do not handle the power plug with wet hands.  
Turn off the projector, unplug the power cable and have the projector serviced by a qualified service personnel under  
the following conditions:  
- When the power cable or plug is damaged or frayed.  
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.  
- If the projector does not operate normally when you follow the instructions described in this user’s manual.  
- If the projector has been dropped or the cabinet has been damaged.  
- If the projector exhibits a distinct change in performance, indicating a need for service.  
• Disconnect the power cable and any other cables before carrying the projector.  
Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.  
Turn off the projector and unplug the power cable if the projector is not to be used for an extended period of time.  
• When using a LAN cable (only models with the RJ-45 LAN port):  
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.  
CAUTION  
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hang-  
ing on the wall can cause damage to the projector.  
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the  
soft case could be damaged.  
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select  
[SETUP] [OPTIONS(1)] [FAN MODE] [HIGH].)  
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while  
the projector is turned on and immediately after the projector is turned off.  
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blink-  
ing green. Doing so could cause premature lamp failure.  
Remote Control Precautions  
Handle the remote control carefully.  
If the remote control gets wet, wipe it dry immediately.  
Avoid excessive heat and humidity.  
Do not heat, take apart, or throw batteries into fire.  
If you will not be using the remote control for a long time, remove the batteries.  
Ensure that you have the batteries’ polarity (+/−) aligned correctly.  
Do not use new and old batteries together, or use different types of batteries together.  
Dispose of used batteries according to your local regulations.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Note for US Residents  
The lamp in this product contains mercury. Please dispose according to Local, State or Federal Laws.  
Lamp Replacement  
To replace the lamp, follow all instructions provided on page 84.  
Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE.  
PLEASE REPLACE THE LAMP.] appears. If you continue to use the lamp after the lamp has reached the end  
of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch  
them as the pieces of glass may cause injury.  
If this happens, contact your dealer for lamp replacement.  
A Lamp Characteristic  
The projector has a high-pressure mercury lamp as a light source.  
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on  
and off will increase the possibility of its lower brightness.  
CAUTION:  
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off  
and then disconnect the power cable. Allow at least one hour for the lamp to cool before handling.  
• When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass  
fragments could fall if the lamp has been burned out.  
About High Altitude mode  
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or  
higher.  
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE]  
can cause the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and  
turn on the projector.  
Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE]  
can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].  
Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical com-  
ponents such as the lamp.  
About Copyright of original projected pictures:  
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue  
such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func-  
tions may raise concern about the infringement of copyrights which are protected by copyright law.  
[ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features.  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
vii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
1 What’s in the Box?  
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.  
Please save the original box and packing materials if you ever need to ship your projector.  
Projector  
Lens cap  
Lens cap  
(24F44681)  
(24FU0691)  
Soft case  
(24BS7582)  
NP610/NP510/NP410/  
NP610S/NP510WS  
NP610/NP510/NP410/ The NP405, NP305,  
NP405/NP310/NP305/  
NP510W/NP410W  
NP310/NP510W/  
NP410W  
NP610S, and NP510WS  
do not come with a soft  
case.  
1
2
Power cable  
(US: 7N080235)  
(EU: 7N080021)  
VGA signal cable  
(7N520073/7N520052)  
Remote control  
(7N900901)  
Batteries (AAA × 2)  
For North America only  
Registration card  
Limited warranty  
For customers in Europe:  
You will find our current valid Guar-  
antee Policy on our Web Site:  
www.nec-display-solutions.com  
NEC Projector CD-ROM  
User’s manual (PDF) and  
the utility software “Virtual  
Remote Tool”  
Important Infomation (For North America:  
7N8P9731) (For Other countries than North  
America: 7N8P9731 and 7N8P9741)  
Quick Setup Guide (7N8P9721)  
(7N951361)  
DVI to VGA adapter (7N960234)  
The NP405 and NP305 do not  
come with the DVI to VGA adapter.  
Unless otherwise described in the user’s manual, the drawings for the projector cabinet show examples of the NP610.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
Introduction to the Projector  
This section introduces you to your new projector and describes the features and controls.  
Congratulations on Your Purchase of the Projector  
This projector is one of the very best projectors available today. The projector enables you to project precise images  
up to 300 inches (110 inches on NP610S; 104 inches on NP510WS) across (measured diagonally) from your PC or  
Macintosh computer (desktop or notebook), VCR, DVD player, or document camera.  
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,  
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.  
1
*
Do not attempt to mount the projector on a ceiling yourself.  
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk  
of bodily injury.  
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance  
with any local building codes. Please consult your dealer for more information.  
Features you’ll enjoy:  
Quick start & Quick Power Off  
Less than 4 seconds* after turning on the power, the projector is ready to display PC or video images.  
* The quick start time is only when [STANDBY MODE] is set to [NORMAL] in the on-screen message.  
The projector can be put away immediately after the projector is powered down. No cool down period is required  
after the projector is turned off from the remote control or cabinet control panel.  
Direct Power Off  
The projector has a feature called “Direct Power Off”.This feature allows the projector to be turned off (even when  
projecting an image) by using the Main Power Switch or disconnecting the AC power supply.  
To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and  
a breaker.  
Less than 1W in standby condition with energy saving technology  
Selecting [POWER-SAVING] for [STANDBY MODE] from the menu can put the projector in power-saving mode  
that consumes only 0.6W (100-130V AC)/0.7W (200-240V AC).  
Carbon Meter  
This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO  
MODE] is set to [ON].  
The amount of CO2 emission reduction will be displayed in the confirmation message at the time of power-off and  
in the INFO of the on-screen menu.  
7W built-in speaker for an integrated audio solution  
Powerful 7 watt speaker provides volume need for large rooms.  
Virtual Remote function  
The Virtual Remote function allows power On/Off and source selection of the projector from your PC by using the  
supplied VGA signal cable. The utility software “Virtual Remote Tool” exclusively for the projector is required to be  
installed from the accompanying NEC Projector CD-ROM onto your computer.  
An accompanying NEC Projector CD-ROM includes the utility software “Virtual Remote Tool” exclusively for the  
projector and user’s manuals in PDF format.  
Short throw distances (NP610S/NP510WS)  
Short focal lenses provide for a larger image using a shorter throw distance when compared to a typical projector  
lens.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
A variety of input ports and a comprehensive array of system control interfaces  
This projector supports input signals on the following ports: DVI-I connector (DVI-I 29 Pin) with HDCP compatible,  
15pin D-Sub, composite and S-video.  
AUTO POWER ON and AUTO POWER OFF features  
The AUTO POWER ON(AC), AUTO POWER ON(COMP1), AUTO POWER OFF, and OFF TIMER features eliminate  
the need to always use the POWER button on the remote control or projector cabinet.  
Preventing unauthorized use of the projector  
Enhanced smart security settings for keyword protection, cabinet control panel lock, security slot, and security  
chain opening to help prevent unauthorized access, adjustments and theft deterrence.  
The optional remote control (NP02RC) allows you to assign a CONTROL ID to the projector  
Multiple projectors can be operated separately and independently with the same single remote control by assigning  
an ID number to each projector.  
Integrated RJ-45 connector for wired networking capability (except NP405/NP305)  
An RJ-45 connector is equipped as standard feature.  
Auto vertical keystone correction  
Auto Keystone feature allows the projector to detect its tilt and correct vertical distortion automatically.  
LCD projector with high resolution and high brightness  
High resolution display - up to UXGA compatible, XGA (NP610/NP510/NP410/NP405/NP310/NP305/NP610S)/  
WXGA (NP510W/NP410W/NP510WS) native resolution.  
Six picture preset modes for user adjustable picture and color settings  
Each picture preset mode can be customized and memorized according to your preference.  
PC Control Port  
You can control the projector with a PC or control system using the PC Control port.  
Optional remote mouse receiver  
You can use the supplied wireless remote control and the optional remote mouse receiver to operate your PC  
mouse from across the room. The optional remote mouse receiver (NP01MR) supports almost any PC using a  
USB connection.  
About this user’s manual  
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to  
review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find  
an overview. If the section doesn’t apply, you can skip it.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
Comparative Table of Main Features  
The main features vary depending on the model as follows.  
Wide Panel &  
Short-Throw  
Model  
Short-Throw  
Model  
Standard Models  
Wide Panel Model  
NP610 NP510 NP410 NP405 NP310 NP305 NP510W NP410W  
NP610S  
NP510WS  
Native Aspect  
Ratio  
(page 90, 92)  
Standard  
Wide  
Standard  
Wide  
Native Resolution  
(dots x lines*1)  
(page 90, 92)  
WXGA  
(1280 x 800)  
XGA  
(1024 x 768)  
WXGA  
(1280 x 800)  
XGA (1024 x 768)  
Screen Size  
(page 90, 92)  
Throw Distance  
(page 90, 92)  
21"–300"  
30–444 inches/0.7–11.3 m  
60"–110"  
57"–104"  
31–470 inches/  
0.8–11.9 m  
35"–66"/  
0.9 m–1.7 m  
36"–66"/  
0.9 m–1.7 m  
Light output*2*3  
in OFF for ECO  
MODE  
(page 90, 92)  
Wired LAN  
3500 3000  
lumens lumens  
3000  
lumens lumens  
2600  
2600 lumens  
2200 lumens  
2600 lumens  
2100 lumens  
RJ-45  
RJ-45  
RJ-45  
(page 24, 48)  
Zoom  
(page 32)  
Focus  
(page 33)  
Using the [DIGITAL ZOOM] function  
Using the manual zoom lever  
Using the manual focus ring  
from the menu  
Using the manual focus lever  
Lamp Replace-  
ment Time (aver-  
age)  
4000 (H) in OFF for ECO MODE /5000 (H) in ON for ECO MODE  
(page 78)  
For further details on the specifications, see page 90.  
*1 Effective pixels are more than 99.99%.  
*2 This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any other mode is  
selected as the [PRESET] mode, the light output value may drop slightly.  
*3 Compliance with ISO21118-2005  
TIP: The model name is located on the cabinet.  
FOCUS  
Model name  
MENU  
LAMP  
STATUS  
SOURCE  
AUTO ADJ.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Part Names of the Projector  
Front/Top  
NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W  
Controls  
(page 7)  
Zoom Lever (page 32)  
Security chain opening  
Attach an anti-theft device.  
The security chain opening accepts se-  
curity wires or chains up to 0.18 inch/  
4.6 mm in diameter.  
Focus Ring  
(page 33)  
Remote sensor  
S
U
C
O
F
(page 10)  
Built-in Security Slot ( )*  
Lens  
Ventilation (inlet) / Filter Cover  
(page 81)  
Lens Cap  
Adjustable Tilt Foot Lever (page 31)  
Adjustable Tilt Foot (page 31)  
*
This security slot supports the MicroSaver ® Security System.  
NP610S/NP510WS  
Controls  
(page 7)  
Security chain opening  
Attach an anti-theft device.  
The security chain opening accepts se-  
curity wires or chains up to 0.18 inch/  
4.6 mm in diameter.  
Focus Lever  
(page 33)  
Remote sensor  
F O C
(page 10)  
Built-in Security Slot ( )*  
Lens  
Ventilation (inlet) / Filter Cover  
(page 81)  
Lens Cap  
*
This security slot supports the MicroSaver ® Security System.  
Adjustable Tilt Foot Lever (page 31)  
Adjustable Tilt Foot (page 31)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
Rear  
Lamp Cover (page 85)  
Monaural Speaker (7W)  
Ventilation (outlet)  
Ventilation (inlet) / Filter Cover  
(page 81)  
Heated air is exhausted from here.  
Terminal Panel (page 8)  
Spacer (black rubber)  
To ne-adjust the height of the rear foot,  
remove the spacer and rotate the rear  
foot to the desired height.  
Rear Foot (page 31)  
AC Input  
Connect the supplied power cable’s two-pin plug here, and  
plug the other end into an active wall outlet. (page 25)  
Main Power Switch  
When you plug the supplied power cable into an active wall outlet  
and turn on the Main Power, the POWER indicator turns orange  
and the projector is in standby mode.  
(page 26, 38)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
Top Features  
7
8
9
10  
4
3
LAMP  
STATUS  
SOURCE AUTO ADJ.  
1 2 5  
6
1.  
(POWER) Button (page 27, 38)  
2. POWER Indicator (page 26, 38, 87)  
3. STATUS Indicator (page 87)  
4. LAMP Indicator (page 84, 87)  
5. SOURCE Button (page 29)  
6. AUTO ADJ. Button (page 37)  
7. MENU Button (page 56)  
8.  / Volume Buttons  / Keystone Buttons  
 (page 34, 37)  
9. ENTER Button (page 56)  
10. EXIT Button (page 56)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1. Introduction  
Terminal Panel Features  
NP610/NP510/NP410/NP310/NP510W/NP410W/NP610S/NP510WS  
6
3
2
1
3 9  
10  
8
7
5
4
NP405/NP305  
6
3
2
1
3 9  
8
7
5
4
1. COMPUTER 1 IN/ Component Input Connector  
(Mini D-Sub 15 Pin) (page 17, 20, 22)  
2. COMPUTER 2 (DVI-I) IN Connector (29 Pin)  
(HDCP compatible) (page 19, 20)  
(NP610/NP510/NP410/NP310/NP510W/NP410W/  
NP610S/NP510WS)  
COMPUTER 2 IN / Component Input Connector  
(Mini D-Sub 15 Pin) (page 17, 20, 22)  
(NP405/NP305)  
3. AUDIO IN Mini Jack (Stereo Mini)  
(page 17, 19, 22)  
4. AUDIO OUT Mini Jack (Stereo Mini) (page 21)  
5. MONITOR OUT (COMP 1) Connector (Mini D-Sub  
15 Pin) (page 21)  
6. S-VIDEO IN Connector (Mini DIN 4 Pin)  
(page 23)  
7. VIDEO IN Connector (RCA) (page 23)  
8. AUDIO Input Jacks L/R (RCA) (page 23)  
9. PC CONTROL [PC CONTROL] Port (D-Sub 9 Pin)  
(page 98)  
Use this port to connect a PC or control system.  
This enables you to control the projector using serial  
communication protocol. If you are writing your own  
program, typical PC control codes are on page 98.  
10. LAN Port (RJ-45) (page 24)  
(not available on NP405/NP305)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1. Introduction  
Part Names of the Remote Control  
1
OFF  
ON  
POWER  
3
2
MAGNIFY AV-MUTE  
PAGE  
UP  
4
7
6
5
8
DOWN  
MENU  
ENTER  
EXIT  
10  
12  
9
L-CLICK  
MOUSE  
R-CLICK  
AUTO ADJ.  
ECO MODE  
HELP  
11  
13  
VIDEO  
C
O
MPUTER
1
16  
15  
18  
S-VIDEO  
2
14  
19  
17  
VOLUME ASPECT  
21  
PICTURE FREEZE  
22  
20  
12. MOUSE R-CLICK Button*  
(page 46, 47)  
1. Infrared Transmitter  
13. VIDEO Button  
(page 10)  
(page 29)  
2. POWER ON Button  
14. S-VIDEO Button  
(page 27)  
(page 29)  
3. POWER OFF Button  
15. COMPUTER 1/2 Button  
(page 38)  
(page 29)  
4. MAGNIFY (+)(−) Button  
16. AUTO ADJ. Button  
(page 40)  
(page 37)  
5. AV-MUTE Button  
17. VOLUME (+)(−) Button  
(page 40)  
(page 37)  
6. PAGE UP/DOWN Button*  
18. ECO MODE Button (page 41)  
(page 46, 47)  
19. ASPECT Button  
7. MENU Button  
(page 66)  
(page 56)  
20. PICTURE Button  
8. SELECT  Button (page 56)  
9. ENTER Button (page 56)  
10. EXIT Button (page 56)  
(page 61, 62)  
21. HELP Button  
(page 78)  
11. MOUSE L-CLICK Button*  
22. FREEZE Button  
(page 46, 47)  
(page 40)  
* The PAGE UP/DOWN, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse  
receiver is connected with your computer.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1. Introduction  
Battery Installation  
1
2
3
Press firmly and slide the battery  
cover off.  
Install new batteries (AAA).Ensure  
that you have the batteriespolarity  
(+/−) aligned correctly.  
Slip the cover back over the bat-  
teries until it snaps into place. Do  
not mix different types of batteries  
or new and old batteries.  
Remote Control Precautions  
Handle the remote control carefully.  
If the remote control gets wet, wipe it dry immediately.  
Avoid excessive heat and humidity.  
Do not heat, take apart, or throw batteries into fire.  
If you will not be using the remote control for a long time, remove the batteries.  
Ensure that you have the batteries’ polarity (+/−) aligned correctly.  
Do not use new and old batteries together, or use different types of batteries together.  
Dispose of used batteries according to your local regulations.  
Operating Range for Wireless Remote Control  
7 m/22 feet  
Remote control  
30°  
30°  
Remote sensor on projector cabinet  
30°  
Remote control  
30°  
7 m/22 feet  
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of  
the remote sensor on the projector cabinet.  
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls  
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
2. Installation and Connections  
This section describes how to set up your projector and how to connect video and audio sources.  
Your projector is simple to set up and use. But before you get started, you must first:  
z
x
Set up a screen and the projector.  
Connect your computer or video equip-  
ment to the projector.  
(page 17, 19, 20, 21, 22, 23, 24)  
c
Connect the supplied power cable.  
(page 25)  
NOTE: Ensure that the power cable and any other  
cables are disconnected before moving the projec-  
tor. When moving the projector or when it is not  
in use, cover the lens with the lens cap.  
To the wall outlet.  
1 Setting Up the Screen and the Projector  
Selecting a Location  
NOTE: Throw distances vary depending on the model.  
[NP610/NP510/NP410/NP405/NP310/NP305]  
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is  
approximately 21" (0.53 m) measured diagonally when the projector is roughly 30 inches (0.8 m) from the wall or  
screen. The largest the image can be is 300" (7.6 m) when the projector is about 407 inches (10.3 m) from the wall  
or screen.  
Screen Size (Unit: cm/inch)  
609.6(W)457.2(H) / 240(W)180(H)  
300"  
Screen Size  
487.7(W)365.8(H) / 192(W)144(H)  
240"  
406.4(W)304.8(H) / 160(W)120(H)  
200"  
365.8(W)274.3(H) / 144(W)108(H)  
180"  
304.8(W)228.6(H) / 120(W)90(H)  
150"  
243.8(W)182.9(H) / 96(W)72(H)  
120"  
203.2(W)152.4(H) / 80(W)60(H)  
100"  
162.6(W)121.9(H) / 64(W)48(H)  
80"  
121.9(W)91.4(H) / 48(W)36(H)  
60"  
81.3(W)61.0(H) / 32(W)24(H)  
40"  
61.0(W)45.7(H) / 24(W)18(H)  
30"  
42.7(W)32(H) / 17(W)13(H)  
"
"
21"  
"
"
"
Lens center  
8.3/325  
"
6.9/271  
10.3/407  
6.2/244  
"
"
"
0.8/  
30  
"
5.1/203  
"
"
1.0/  
40  
4.1/162  
2.0/81  
3.4/135  
2.7/107  
1.3/53  
m/inch)  
(Unit:  
Distance  
TIP:  
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.  
• The Zoom lever adjusts the image size by up to +/−10%.  
• For more details on throw distance, see page 15.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Installation and Connections  
[NP510W/NP410W]  
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is  
approximately 21" (0.53 m) measured diagonally when the projector is roughly 31 inches (0.8 m) from the wall or  
screen. The largest the image can be is 300" (7.6 m) when the projector is about 431 inches (11.0 m) from the wall  
or screen.  
Screen Size (Unit: cm/inch)  
646.2(W)403.9(H) / 254(W)159(H)  
300"  
Screen Size  
516.9(W)323.1(H) / 204(W)127(H)  
240"  
430.8(W)269.2(H) / 170(W)106(H)  
200"  
387.7(W)242.3(H) / 153(W)95(H)  
180"  
323.1(W)201.9(H) / 127(W)79(H)  
150"  
258.5(W)161.5(H) / 102(W)64(H)  
120"  
215.4(W)134.6(H) / 85(W)53(H)  
100"  
172.3(W)107.7(H) / 68(W)42(H)  
80"  
129.2(W)80.8(H) / 51(W)32(H)  
60"  
86.2(W)53.8(H) / 34(W)21(H)  
40"  
64.6(W)40.4(H) / 25(W)16(H)  
30"  
45.2(W)28.3(H) / 18(W)11(H)  
"
"
21"  
"
"
"
Lens center  
8.8/345  
"
7.3/287  
11.0/431  
6.6/258  
"
"
"
0.8/  
31  
"
5.5/215  
"
"
0.9/  
42  
4.4/172  
2.2/85  
3.6/143  
2.9/114  
1.4/56  
m/inch)  
(Unit:  
Distance  
TIP:  
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.  
• The Zoom lever adjusts the image size by up to +/−10%.  
• For more details on throw distance, see page 15.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
[NP610S]  
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is ap-  
proximately 60" (1.52 m) measured diagonally when the projector is roughly 35 inches (0.9 m) from the wall or screen.  
The largest the image can be is 110" (2.8 m) when the projector is about 66 inches (1.7 m) from the wall or screen.  
Screen Size (Unit: cm/inch)  
223.5(W)167.6(H)/88(W)66(H)  
110"  
100"  
Screen Size  
203.2(W)152.4(H)/80(W)60(H)  
182.9(W)137.2(H)/72(W)54(H)  
90"  
162.6(W)121.9(H)/64(W)48(H)  
80"  
77"  
70"  
64"  
156.5(W)117.3(H)/62(W)46(H)  
142.2(W)106.7(H)/56(W)42(H)  
130.0(W)97.5(H)/51(W)38(H)  
121.9(W)91.4(H)/48(W)36(H)  
60  
"
Lens center  
1.67/66"  
1.51/59"  
1.36/53"  
1.20/47"  
0.90  
/35"  
1.16/46"  
1.05/41"  
0.96/38"  
m/inch)  
(Unit:  
Distance  
TIP:  
• Digital Zoom can result in a blurry image due to the electronic zoom.  
• The Digital Zoom function adjusts the image size by up to −20%. (page 32)  
• For more details on throw distance, see page 16.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
[NP510WS]  
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is ap-  
proximately 57" (1.45 m) measured diagonally when the projector is roughly 36 inches (0.9 m) from the wall or screen.  
The largest the image can be is 104" (2.6 m) when the projector is about 66 inches (1.7 m) from the wall or screen.  
Screen Size (Unit: cm/inch)  
224.0(W)140.0(H)/88(W)55(H)  
Screen Size  
104"  
215.4(W)134.6(H)/85(W)53(H)  
100"  
193.9(W)121.2(H)/76(W)48(H)  
90"  
187.4(W)117.1(H)/74(W)46(H)  
87"  
172.3(W)107.7(H)/68(W)42(H)  
80"  
150.8(W)94.2(H)/59(W)37(H)  
70"  
129.2(W)80.8(H)/51(W)32(H)  
60"  
122.8(W)76.7(H)/48(W)30(H)  
57  
"
Lens center  
1.67/66"  
1.60/63"  
1.44/57"  
1.39/55"  
0.90  
/36"  
1.28/50"  
1.11/44"  
0.95/37"  
m/inch)  
(Unit:  
Distance  
TIP:  
• Digital Zoom can result in a blurry image due to the electronic zoom.  
• The Digital Zoom function adjusts the image size by up to −20%. (page 32)  
• For more details on throw distance, see page 16.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Throw Distance and Screen Size  
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the  
position of installation.  
Distance Chart [NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]  
C
B = Vertical distance between lens center and  
screen center  
C = Throw distance  
D = Vertical distance between lens center and  
Screen center  
screen bottom (top of screen for ceiling ap-  
plication)  
α = Throw angle  
B
Lens center  
α
D
NOTE: The values in the tables are design values and  
may vary.  
Screen bottom  
[NP610/NP510/NP410/NP405/NP310/NP305]  
α
Screen Size  
Width  
C
B
D
Diagonal  
Height  
wide  
tele  
wide  
degree  
-
tele  
degree  
8.3  
8.3  
8.2  
8.1  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
7.9  
7.9  
7.9  
7.9  
inch  
21  
25  
mm  
533  
635  
inch  
17  
20  
mm  
427  
508  
inch  
13  
15  
mm  
320  
381  
inch  
4
5
6
8
mm  
110  
131  
157  
210  
314  
377  
419  
440  
471  
524  
629  
786  
inch  
-
29  
36  
48  
73  
87  
97  
102  
110  
122  
147  
184  
221  
246  
258  
295  
332  
369  
mm  
-
746  
903  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
inch  
30  
36  
43  
58  
mm  
753  
903  
inch  
-2  
-2  
-3  
-4  
-6  
-7  
-8  
-8  
mm  
-50  
-60  
-71  
-95  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10.0  
9.9  
9.8  
9.7  
9.6  
9.6  
9.6  
9.6  
9.6  
9.6  
9.5  
9.5  
9.5  
9.5  
9.5  
9.5  
9.5  
30  
40  
60  
72  
80  
84  
90  
100  
120  
150  
180  
200  
210  
240  
270  
300  
762  
24  
32  
610  
813  
18  
24  
457  
610  
1092  
1469  
2223  
2675  
2977  
3128  
3354  
3731  
4485  
5616  
6747  
7501  
7878  
9009  
1016  
1524  
1829  
2032  
2134  
2286  
2540  
3048  
3810  
4572  
5080  
5334  
6096  
6858  
7620  
1217  
1845  
2221  
2473  
2598  
2787  
3101  
3729  
4671  
5613  
6241  
6555  
7497  
8439  
9381  
48  
58  
64  
67  
72  
80  
96  
120  
144  
160  
168  
192  
216  
240  
1219  
1463  
1626  
1707  
1829  
2032  
2438  
3048  
3658  
4064  
4267  
4877  
5486  
6096  
36  
43  
48  
50  
54  
60  
72  
90  
108  
120  
126  
144  
162  
180  
914  
12  
15  
17  
17  
19  
21  
25  
31  
37  
41  
43  
50  
56  
62  
88  
-143  
-171  
-191  
-200  
-214  
-238  
-286  
-357  
-429  
-476  
-500  
-572  
-643  
-714  
1097  
1219  
1280  
1372  
1524  
1829  
2286  
2743  
3048  
3200  
3658  
4115  
4572  
105  
117  
123  
132  
147  
177  
221  
266  
295  
310  
355  
-8  
-9  
-11  
-14  
-17  
-19  
-20  
-23  
-25  
-28  
943  
1048  
1100  
1257  
1414  
1572  
399 10140  
444 11271  
[NP510W/NP410W]  
α
Screen Size  
Width  
C
B
D
Diagonal  
Height  
wide  
tele  
wide  
degree  
-
tele  
degree  
8.3  
8.3  
8.2  
8.1  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
8.0  
7.9  
7.9  
7.9  
7.9  
inch  
21  
25  
mm  
533  
635  
inch  
18  
21  
mm  
452  
538  
inch  
11  
13  
mm  
283  
337  
inch  
5
5
7
9
mm  
117  
139  
167  
222  
333  
400  
444  
466  
500  
555  
666  
833  
1000  
1111  
1166  
1333  
1499  
1666  
inch  
-
31  
38  
51  
77  
93  
103  
108  
116  
129  
156  
195  
234  
260  
274  
313  
352  
391  
mm  
-
791  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
inch  
31  
38  
46  
61  
mm  
798  
957  
inch  
-1  
-1  
-1  
-2  
-3  
-3  
-4  
-4  
-4  
-5  
-6  
-7  
-8  
-9  
-10  
-11  
-13  
-14  
mm  
-25  
-29  
-35  
-47  
-71  
-85  
-94  
-99  
-106  
-118  
-141  
-177  
-212  
-236  
-247  
-283  
-318  
-353  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10.0  
9.9  
9.8  
9.7  
9.6  
9.6  
9.6  
9.6  
9.6  
9.6  
9.5  
9.5  
9.5  
9.5  
9.5  
9.5  
9.5  
30  
40  
60  
72  
80  
84  
90  
100  
120  
150  
180  
200  
210  
240  
270  
300  
762  
25  
34  
646  
862  
16  
21  
404  
538  
957  
1158  
1557  
2356  
2835  
3156  
3316  
3555  
3955  
4754  
5953  
7152  
7951  
8351  
9550  
1016  
1524  
1829  
2032  
2134  
2286  
2540  
3048  
3810  
4572  
5080  
5334  
6096  
6858  
7620  
1290  
1956  
2354  
2621  
2754  
2954  
3287  
3953  
4951  
5950  
6615  
6948  
7947  
8945  
9944  
51  
61  
68  
71  
76  
85  
102  
127  
153  
170  
178  
204  
229  
254  
1292  
1551  
1723  
1809  
1939  
2154  
2585  
3231  
3877  
4308  
4523  
5169  
5816  
6462  
32  
38  
808  
969  
13  
16  
17  
18  
20  
22  
26  
33  
39  
44  
46  
52  
59  
66  
93  
112  
124  
131  
140  
156  
187  
234  
282  
313  
329  
376  
42  
45  
48  
53  
64  
79  
95  
106  
111  
127  
143  
159  
1077  
1131  
1212  
1346  
1615  
2019  
2423  
2692  
2827  
3231  
3635  
4039  
423 10748  
470 11947  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Distance Chart [NP610S/NP510WS]  
C
B = Vertical distance between lens center and  
screen center  
C = Throw distance  
D = Vertical distance between lens center and  
screen bottom (top of screen for ceiling ap-  
plication)  
Screen center  
B
α = Throw angle  
Lens center  
α
D
NOTE: The values in the tables are design values and  
may vary.  
Screen bottom  
[NP610S]  
α
wide  
Screen Size  
Width  
C
wide  
B
D
Diagonal  
Height  
inch  
60  
64  
70  
77  
80  
90  
100  
110  
mm  
inch  
48  
51  
56  
62  
64  
72  
80  
88  
mm  
1219  
1300  
1422  
1565  
1626  
1829  
2032  
2235  
inch  
mm  
914  
975  
1067  
1173  
1219  
1372  
1524  
1676  
inch  
mm  
505  
538  
589  
648  
673  
757  
841  
926  
inch  
35  
38  
41  
46  
47  
53  
59  
66  
mm  
895  
956  
1049  
1156  
1203  
1357  
1511  
1665  
inch  
2
2
2
2
3
3
3
3
mm  
48  
51  
56  
61  
64  
71  
79  
87  
degree  
29.4  
29.4  
29.3  
29.3  
29.2  
29.2  
29.1  
29.1  
1524  
1626  
1778  
1956  
2032  
2286  
2540  
2794  
36  
38  
42  
46  
48  
54  
60  
66  
20  
21  
23  
26  
27  
30  
33  
36  
[NP510WS]  
α
Screen Size  
Width  
C
wide  
B
D
Diagonal  
Height  
wide  
degree  
29.4  
29.4  
29.3  
29.2  
29.1  
29.1  
29.1  
29.1  
inch  
57  
mm  
1448  
1524  
1778  
2032  
2210  
2286  
2388  
2642  
inch  
48  
51  
59  
68  
74  
76  
80  
88  
mm  
1228  
1292  
1508  
1723  
1874  
1939  
2025  
2240  
inch  
30  
32  
37  
42  
46  
48  
50  
55  
mm  
767  
808  
inch  
20  
21  
25  
28  
31  
32  
33  
37  
mm  
508  
535  
624  
713  
776  
803  
838  
928  
inch  
36  
37  
44  
50  
55  
57  
59  
66  
mm  
902  
951  
1114  
1277  
1392  
1441  
1506  
1669  
inch  
5
5
6
7
7
8
8
9
mm  
125  
131  
153  
175  
190  
197  
206  
228  
60  
70  
942  
80  
87  
1077  
1171  
1212  
1265  
1400  
90  
94  
104  
WARNING  
Reflecting the Image  
* Installing your projector on the ceiling must be done  
by a qualified technician. Contact your NEC dealer for  
more information.  
* Do not attempt to install the projector yourself.  
• Only use your projector on a solid, level surface. If the  
projector falls to the ground, you can be injured and  
the projector severely damaged.  
Using a mirror to reflect your projector’s image enables  
you to enjoy a much larger image when a smaller space  
is required. Contact your NEC dealer if you need a mirror  
system. If you’re using a mirror system and your image  
is inverted, use the MENU and  buttons on your  
projector cabinet or your remote control to correct the  
orientation. (page 72)  
• Do not use the projector where temperatures vary  
greatly. The projector must be used at temperatures  
between 41°F (5°C) and 104°F (40°C) (Eco mode se-  
lected automatically at 95°F to 104°F/35°C to 40°C).  
• Do not expose the projector to moisture, dust, or  
smoke. This will harm the screen image.  
• Ensure that you have adequate ventilation around your  
projector so heat can dissipate. Do not cover the vents  
on the side or the front of the projector.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Making Connections  
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode  
and before turning on the power to the notebook PC.  
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.  
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage-  
ment software.  
Enabling the computer’s external display  
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.  
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.  
Usually, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on  
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through  
external display selections.  
Connecting Your PC or Macintosh Computer  
NOTE: Signals supported by Plug & Play (DDC2)  
INPUT  
Model  
COMPUTER 1 IN  
analog  
COMPUTER 2 IN  
analog  
Yes  
digital  
Yes  
NP610/NP510/NP410/NP310/  
NP510W/NP410W/NP610S/NP510WS  
Yes  
Yes  
NP405/NP305  
Yes  
NP405/NP305  
AUDIO IN  
COMPUTER 2 IN  
COMPUTER 1 IN  
Audio cable  
(not supplied)  
VGA signal cable (supplied)  
To mini D-Sub 15-pin connector on  
the projector. It is recommended that  
you use a commercially available  
distribution amplifier if connecting a  
signal cable longer than the cable  
supplied.  
NOTE: For older Macintosh, use a commercially available  
pin adapter (not supplied) to connect to your Mac’s video  
port.  
PHONE  
IBM VGA or Compatibles (Notebook  
type) or Macintosh (Notebook type)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
• Select the source name for its appropriate input connector after turning on the projector.  
[NP610/NP510/NP410/NP310/NP510W/NP410W/NP610S/NP510WS]  
SOURCE button on the projector  
Input connector  
Button on the remote control  
(COMPUTER 1)  
cabinet  
COMPUTER 1 IN  
COMPUTER1  
COMPUTER 2(DIGITAL)  
or  
COMPUTER 2(DVI-I)IN  
(COMPUTER 2)  
COMPUTER 2(ANALOG)  
[NP405/NP305]  
SOURCE button on the projector  
Input connector  
Button on the remote control  
cabinet  
COMPUTER 1 IN  
COMPUTER 2 IN  
COMPUTER 1  
COMPUTER 2  
(COMPUTER 1)  
(COMPUTER 2)  
NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher.  
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan  
converter.  
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.  
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:  
Project an image to fill the screen and then press the AUTO ADJ. button on the remote control or the projector cabinet.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
When Viewing a DVI Digital Signal (except NP405 and NP305)  
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before  
turning on your PC or projector.Turn on the projector first and select Computer 2 (Digital) from the source menu before  
turning on your PC.  
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should  
this happen, restart your PC.  
Do not disconnect the DVI cable while the projector is running. If the signal cable has been disconnected and then  
re-connected, an image may not be correctly displayed. Should this happen, restart your PC.  
NOTE:  
• Use a DVI cable or the one compliant with the DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0  
standard. The DVI cable should be within 5 m (196") long. Both single and dual types of DVI cable can be used.  
• The DVI (DIGITAL) connector accepts VGA (640 x 480), SVGA (800 x 600), 1152 x 864, XGA (1024 x 768), WXGA (1280 x 800  
@ up to 60Hz), and SXGA (1280 x 1024 @ up to 60Hz).  
IBM PC or Compatibles (Desktop type)  
or Macintosh (Desktop type)  
PHONE  
Audio cable (not supplied)  
DVI cable (not supplied)  
COMPUTER 2 (DVI-I) IN  
AUDIO IN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Using Two Analog COMPUTER Inputs Simultaneously  
If you need to use two analog COMPUTER inputs simultaneously, connect a VGA signal cable as shown below.  
COMPUTER 2 (DVI-I) IN  
NP405/NP305  
COMPUTER 1 IN  
AUDIO IN  
COMPUTER 2 IN  
DVI to VGA adapter  
(supplied)  
Audio cable (not supplied)  
VGA signal cable (not  
supplied)  
VGA signal cable  
(supplied)  
PHONE  
IBM PC or Compatibles (Notebook type)  
or Macintosh (Notebook type)  
IBM PC or Compatibles (Desktop  
type) or Macintosh (Desktop type)  
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do so  
may cause damage to the connector of the projector.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Connecting an External Monitor  
AUDIO OUT  
MONITOR OUT (COMP 1)  
VGA signal cable (not supplied)  
VGA signal  
cable (sup-  
plied)  
AUDIO  
IN  
PHONE  
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer  
analog image you’re projecting.  
NOTE:  
• Daisy chain connection is not possible.  
• When audio equipment is connected, the projector speaker is disabled.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Connecting Your DVD Player with Component Output  
COMPUTER 1 IN  
AUDIO IN  
15-pin - to - RCA (fe-  
male) × 3 cable adapter  
(ADP-CV1E)  
Audio Equipment  
Component video RCA × 3  
cable (not supplied)  
AUDIO IN  
L
R
DVD player  
L
R
Y
Cb Cr  
Audio cable (not supplied)  
AUDIO OUT  
Component  
A component signal will be automatically displayed. If not, from the menu, select [SETUP] [OPTIONS(1)] →  
[SIGNAL SELECT] [COMPUTER1], and then place a check mark in the Component radio button.  
• Select the source name for its appropriate input connector after turning on the projector.  
[NP610/NP510/NP410/NP310/NP510W/NP410W/NP610S/NP510WS]  
SOURCE button on the projector  
Input connector  
Button on the remote control  
cabinet  
COMPUTER 1 IN  
COMPUTER1  
(COMPUTER 1)  
(COMPUTER 2)  
COMPUTER 2 (DVI-I) IN  
COMPUTER 2(ANALOG)  
[NP405/NP305]  
SOURCE button on the projector  
Input connector  
Button on the remote control  
cabinet  
COMPUTER 1 IN  
COMPUTER 2 IN  
COMPUTER 1  
COMPUTER 2  
(COMPUTER 1)  
(COMPUTER 2)  
NOTE: Refer to your DVD player’s owner’s manual for more information about your DVD player’s video output requirements.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Connecting Your VCR  
S-VIDEO IN  
AUDIO IN  
VIDEO IN  
S-Video cable (not supplied)  
Audio cable (not supplied)  
Video cable (not supplied)  
Audio equipment  
VCR  
L
R
VIDEO S-VIDEO  
VIDEO OUT  
AUDIO IN  
AUDIO OUT  
L
R
Audio cable (not supplied)  
• Select the source name for its appropriate input connector after turning on the projector.  
SOURCE button on the projector  
Input connector  
Button on the remote control  
cabinet  
VIDEO IN  
VIDEO  
(VIDEO)  
S-VIDEO IN  
(S-VIDEO)  
S-VIDEO  
NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video and S-Video inputs.  
NOTE: Refer to your VCR owner’s manual for more information about your equipment’s video output requirements.  
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via  
a scan converter.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Connecting to a Network (except NP405 and NP305)  
The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable.  
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a LAN.  
To use a LAN connection, you are required to assign an IP address to the projector on the [PROJECTOR NETWORK  
SETTINGS] screen of the web browser on your computer. For setting, see page 48, 49, 50.  
Example of LAN connection  
Example of wired LAN connection  
Server  
Hub  
NOTE: Use a Category 5 or higher LAN cable.  
LAN cable (not supplied)  
LAN  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2. Installation and Connections  
Connecting the Supplied Power Cable  
Connect the supplied power cable to the projector.  
First connect the supplied power cable’s two-pin plug to the AC IN of the projector, and then connect the other plug  
of the supplied power cable in the wall outlet.  
FOC  
US  
MEN  
U
E
T
ER  
EXIT  
SOU  
RC  
E
A
UT  
O
AD  
LA  
J
MP  
.
ST  
A
TU  
S
To wall outlet ←  
Make sure that the prongs are fully inserted into both  
the AC IN and the wall outlet.  
CAUTION:  
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while  
the projector is turned on and immediately after the projector is turned off.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
This section describes how to turn on the projector and to project a picture onto the screen.  
1 Turning on the Projector  
NOTE:  
• The projector has two power switches: a main power switch and a  
(POWER) button (POWER ON and OFF on the remote  
control).  
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off () posi-  
tion. Failure to do so may cause damage to the projector.  
1. Remove the lens cap  
• Do not remove the lens cap by pulling on the string.Doing  
so can cause mechanical damage to the part around the  
lens.  
U S  
C
F O  
U S  
O C  
F
2. To turn on the main power to the projector, press the  
Main Power switch to the on position ( I ).  
The projector will go into standby mode. When in standby  
mode, the POWER indicator will light orange and the STA-  
LAMP  
STATUS  
TUS indicator will light green when [NORMAL] is selected  
SOURCE  
AUTO ADJ.  
for [STANDBY MODE].  
See the Power Indicator section.(page 87)  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
LAMP  
3. Press the  
(POWER) button on the projector cabinet  
STATUS  
SOURCE  
AUTO ADJ.  
or the POWER ON button on the remote control for 1  
second.  
The POWER indicator will turn to green and the projector  
will become ready to use.  
OFF  
ON  
POWER  
MAGNIFY AV-MUTE  
PE  
NOTE: When the projector is turned on, it may take some time  
before the lamp light becomes bright.  
DOWN  
MENU  
TIP:  
• When the STATUS indicator lights orange, it means that the  
[CONTROL PANEL LOCK] is turned on. (page 72)  
• When the message “Projector is locked! Enter your password.”  
is displayed, it means that the [SECURITY] is turned on. (→  
page 43)  
Standby  
Blinking  
Power On  
LAMP  
STATUS  
SOURCE  
AUTO ADJ.  
After you turn on your projector, ensure that the computer  
or video source is turned on and that your lens cap is  
removed.  
Steady orange light  
Blinking green  
light  
Steady green  
light  
(page 87)  
NOTE: When no signal is available, the NEC logo, blue (default), or  
black screen will be displayed. When the projector displays the NEC  
logo, a blue or black screen, the projector will automatically switch  
to [ECO MODE].  
The projector will return ECO MODE to its previous setting once an  
active signal is connected.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Projecting an Image (Basic Operation)  
Note on Startup screen (Menu Language Select screen)  
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one  
of the 21 menu languages.  
To select a menu language, follow these steps:  
1. Use the , , or button to select one of the 21  
OFF  
ON  
POWER  
languages from the menu.  
MENU  
MAGNIFY AV-MUTE  
PAGE  
UP  
DOWN  
MENU  
ENTER  
EXIT  
OFF  
ON  
POWER  
MENU  
MAGNIFY AV-MUTE  
PAGE  
2. Press the ENTER button to execute the selection.  
UP  
DOWN  
MENU  
ENTER  
After this has been done, you can proceed to the menu  
operation.  
If you want, you can select the menu language later.  
([LANGUAGE] on page 58 and 70)  
EXIT  
NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp light-  
ing is stabilized.  
NOTE: If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for some time  
and then the projector will display the image.  
CAUTION:  
The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking  
green. Doing so could cause premature lamp failure.  
When the [ECO MODE] is set to [ON], the LAMP indicator will light green.  
If one of the following things happens, the projector will not turn on.  
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this  
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector’s internal  
components to cool down.  
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.  
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and  
then turn on the power.  
NOTE: Turning the Main Power Switch Off then Back On  
Allow a minimum of 1 second between turning off the main power switch and turning it back on again.  
The same will be applied when a power strip equipped with a switch and a breaker is used.  
Failing to do so could result in no power to the projector. (There will be no stand-by LED)  
Should this happen, unplug the power cable and plug it in again. Turn on the main power switch.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Projecting an Image (Basic Operation)  
Selecting a Source  
Selecting the computer or video source  
MENU  
NOTE: Turn on the computer or video source equipment connected to the projector.  
Selecting from Source List  
Press and quickly release the SOURCE button on the projector cabinet to  
display the Source list.Each time the SOURCE button is pressed, the input  
source will change as follows:COMPUTER1”, “COMPUTER2(DIGITAL/  
ANALOG)”, “COMPUTER2” (on the NP405 and NP305 only), “VIDEO”,  
“S-VIDEO”. To display the selected source, allow 1 second to elapse.  
LAMP  
STATUS  
SO
AUTO ADJ.  
Detecting the Signal Automatically  
Press and hold the SOURCE button for a minimum of 2 seconds, the  
projector will search for the next available input source. Each time you  
press and hold the SOURCE button for a minimum of 2 seconds, the  
input source will change as follows:  
[NP610/NP510/NP410/NP310/NP510W/  
NP410W/NP610S/NP510WS]  
COMPUTER1 COMPUTER2(DIGITAL) COMPUTER2(ANALOG)  
VIDEO S-VIDEO COMPUTER1 ...  
TIP: If no input signal is present, the input will be skipped.  
[NP405/NP305]  
Using the Remote Control  
L-CLICK  
R-CLICK  
Press any one of the COMPUTER 1/2, VIDEO, and S-VIDEO buttons.  
MOUSE  
VIDEO  
COMPUTER
1
S-VIDEO  
ECO MODE  
TIP: The COMPUTER 2 button on the remote control toggles the Computer 2  
source between [COMPUTER2(DIGITAL)] and [COMPUTER2(ANALOG)] (except  
on the NP405 and NP305).  
2
VOME ASPECT  
HELP  
RE FREEZE  
Selecting Default Source  
You can set a source as the default source so that it will be displayed  
each time the projector is turned on.  
1. Press the MENU button.  
The menu will be displayed.  
2. Press the button twice to select [SETUP] and press the but-  
ton or the ENTER button to select [GENERAL].  
3. Press the  
button three times to select [OPTIONS(2)].  
4. Press the button six times to select [DEFAULT SOURCE SE-  
LECT] and press the ENTER button.  
The [DEFAULT SOURCE SELECT] screen will be displayed.  
(page 77)  
5. Select a source as the default source, and press the ENTER but-  
ton.  
[NP610/NP510/NP410/NP310/NP510W/  
NP410W/NP610S/NP510WS]  
6. Press the EXIT button a few times to close the menu.  
7. Restart the projector.  
The source you selected in step 5 will be projected.  
TIP: When the projector is in Standby mode, applying a computer signal from a  
computer connected to the COMPUTER 1 IN input will power on the projector  
and simultaneously project the computer’s image.  
([AUTO POWER ON(COMP1)] page 77)  
[NP405/NP305]  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3. Projecting an Image (Basic Operation)  
Adjusting the Picture Size and Position  
Use the adjustable tilt foot, the zoom function or the focus ring to adjust the picture size and position.  
In this chapter drawings and cables are omitted for clarity.  
Adjusting the throw angle (the height of an image)  
Adjusting the left and right tilt of an image  
[Tilt foot] (page 31)  
[Rear foot] (page 31)  
Finely adjusting the size of an image  
Adjusting the focus  
[Zoom function] (page 32)  
[Focus ring] (page 33)  
Adjusting the keystone correction [KEYSTONE]* (page 34)  
* Keystone correction can be also performed automatically. (page 36)  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
Adjust the Tilt Foot  
1. Lift the front edge of the projector.  
1
CAUTION:  
Do not try to touch the ventilation outlet during Tilt Foot adjustment  
as it can become heated while the projector is turned on and after it  
is turned off.  
2
Adjustable Tilt  
Foot Lever  
Adjustable Tilt Foot  
2. Push up and hold the Adjustable Tilt Foot Lever on the front of  
the projector to extend the adjustable tilt foot.  
3. Lower the front of the projector to the desired height.  
4. Release the Adjustable Tilt Foot Lever to lock the Adjustable tilt  
foot.  
1
The tilt foot can be extended up to 1.5 inch/38 mm.  
There is approximately 10 degrees (up) of adjustment for the front of  
the projector.  
Rotate the rear foot to the desired height in order to square the image  
on the projection surface.  
2
Adjustable Tilt  
Foot Lever  
CAUTION:  
• Do not use the tilt-foot for purposes other than originally intended.  
Misuses such as using the tilt foot to carry or hang (from the wall or  
ceiling) the projector can cause damage to the projector.  
Adjusting the left and right tilt of an image [Rear foot]  
1. Remove the spacer (black rubber) from the rear foot.  
Keep the spacer for future use.  
4
2. Rotate the rear foot.  
3
The rear foot can be extended up to 0.4 inch/10 mm. Rotating the rear  
foot allows the projector to be placed horizontally.  
NOTE:  
• Do not extend the rear foot beyond its height limit (0.4 inch/10 mm). Doing so  
may cause the rear foot to come out of the projector.  
• After using the projector, attach the spacer to the rear foot.  
Rear foot  
Spacer (black  
rubber)  
Up  
Down  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3. Projecting an Image (Basic Operation)  
Zoom  
[NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]  
Use the ZOOM lever to adjust the image size on the screen.  
Zoom Lever  
S
U
C
O
F
F O C U S  
[NP610S/NP510WS]  
The image size can be adjusted electronically from the menu. To do so, follow the steps below.  
Adjusting from the menu  
1. Press the MENU button.  
The menu will be displayed.  
2. Press the button to select [SETUP] and press the ENTER button.  
The [GENERAL] tab will be highlighted.  
3. Press the button.  
The [DIGITAL ZOOM] will be highlighted.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
4. Use the or button to adjust the image size.  
5. After completing adjustment, press the EXIT button three times.  
The menu will be closed.  
Focus  
[NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]  
Use the FOCUS ring to obtain the best focus.  
Focus Ring  
C
O
F
F O C U S  
[NP610S/NP510WS]  
Use the FOCUS lever to obtain the best focus.  
Focus Lever  
F O C U
F O C U S  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
Correcting Keystone Distortion  
Correcting Keystone Distortion  
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following  
steps to correct keystone distortion  
NOTE:  
• The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.  
• The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.  
Adjusting with buttons on the cabinet  
1. Press the or button with no menus displayed.  
The keystone bar will be displayed.  
MENU  
LAMP  
STATUS  
SOURCE  
AUTO ADJ.  
2. Use the or to correct the keystone distortion.  
The keystone bar will be closed after a period of time.  
3. Press the ENTER button.  
The keystone bar will be closed.  
NOTE: When the menu is displayed, the above operation is not available. When the menu is displayed, press the MENU button to  
close the menu and start the Keystone correction.  
From the menu, select [SETUP] [GENERAL] [KEYSTONE]. The changes can be saved with [KEYSTONE SAVE]. (page 36,  
68)  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
Adjusting from the menu  
1. Press the MENU button.  
The menu will be displayed.  
2. Press the button to select [SETUP] and press the ENTER button.  
The [GENERAL] screen will be displayed.  
3. Press the button to select [KEYSTONE].  
4. Press the or button.  
Adjust so that the image is rectangular.  
5. After completing adjustment, press the EXIT button three times.  
The menu will be closed.  
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.  
TIP: The changes can be saved with [KEYSTONE SAVE]. (page 36, 68)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Projecting an Image (Basic Operation)  
Adjusting with the Auto Keystone Function  
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special  
operation required. Just put the projector on a flat surface.  
TIP: Even when the menu setting for [AUTO KEYSTONE] is turned on, [KEYSTONE] can be adjusted manually.  
To turn on [AUTO KEYSTONE], proceed the following steps.  
1. Press the MENU button  
The menu will be displayed.  
2. Press the button to select [SETUP] and press the ENTER button.  
The [GENERAL] screen will be highlighted.  
3. Press the button.  
The [AUTO KEYSTONE] will be highlighted.  
4. Press the ENTER button to display the [AUTO KEYSTONE] screen.  
5. Press the or button to select [ON] and press the ENTER button.  
6. Press the MENU button.  
The menu will be closed.  
NOTE:  
• The maximum range of vertical keystone correction is +/−30 degrees on the NP610/NP510/NP410/NP405/NP310/NP305/NP510W/  
NP410W and +/−20 degrees on the NP610S/NP510WS.  
The maximum range of keystone correction may be lower depending on the signal or aspect ratio selection.  
The range of keystone correction is not the maximum tilt angle of projector.  
• The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection.  
• The left and right (horizontal) keystone correction is not available.  
Place the projector so that the lens surface is parallel to the screen.  
The rear feet of the projector can be adjusted to level the projector.  
• Using keystone correction can cause the image to be slightly blurred because the correction is made electronically.  
TIP: If you have one of the following conditions, the projector’s Auto Keystone may not be performed correctly.  
• The screen is tilted  
• The room temperature is too high or too low  
• The optical zoom is maximized or minimized  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
Optimizing Computer Signal Automatically  
Adjusting the Image Using Auto Adjust  
Optimizing a computer image automatically.  
Press the AUTO ADJ. button to optimize a computer image automatically.  
This adjustment may be necessary when you connect your computer for the first time.  
[Poor picture]  
MENU  
L-CLICK  
R-CLICK  
MOUSE  
VIDEO  
COMPUTER
1
S-VIDEO  
ECO DE  
2
VOLUME ASPECT  
PICTURE FREEZE  
LAMP  
STATUS  
SOURCE  
AUTJ.  
[Normal picture]  
NOTE:  
Some signals may take time to display or may not be displayed correctly.  
• The Auto Adjust function does not work for component, video, and DVI digital signals.  
• If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE]  
manually. (page 64, 65)  
Turning Up or Down Volume  
L-CLICK  
R-CLICK  
Sound level from the speaker can be adjusted.  
MOUSE  
VIDEO  
COMPUTER
1
S-VIDEO  
ECO MODE  
2
Increase volume  
Decrease volume  
VOLUME ASPECT  
HELP  
PICTURE FREEZE  
TIP: When no menus appear, the and buttons on the projector cabinet work as a volume control.  
MENU  
LAMP  
STATUS  
SOURCE  
AUTO ADJ.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3. Projecting an Image (Basic Operation)  
7 Turning off the Projector  
MENU  
To turn off the projector:  
OFF  
ON  
POWER  
1. First, press the  
(POWER) button on the projector  
MAFY AV-MUTE  
PAGE  
UP  
cabinet or the POWER OFF button on the remote con-  
trol.  
DOWN  
MENU  
ENTER  
The [POWER OFF / ARE YOU SURE? / CARBON SAV-  
INGS- SESSION 0.000[g-CO2]] message will appear.  
LAMP  
STATUS  
EXIT  
SOURCE  
AUTO ADJ.  
2. Secondly, press the ENTER button or press the  
(POWER) or the POWER OFF button again.  
Power On  
Standby  
The lamp will turn off and the projector will go into standby  
mode. When in standby mode, the POWER indicator will  
light orange and the STATUS indicator will light green when  
[NORMAL] is selected for [STANDBY MODE].  
Steady green  
light  
Steady  
orange light  
Immediately after turning on the projector and displaying an  
image, you cannot turn off the projector for 60 seconds.  
3. Finally, turn off the Main Power switch.  
The POWER indicator will go out.  
NOTE: Do not turn off the main power within 10 seconds of making  
adjustment or setting changes and closing the menu.  
Doing so can cause loss of adjustments and settings.  
CAUTION:  
Parts of the projector will become heated during operation. Use caution when picking up the projector immediately  
after it has been operating.  
CAUTION:  
The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is  
blinking green. Doing so could cause premature lamp failure.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. Projecting an Image (Basic Operation)  
After Use  
Preparation: Make sure that the projector is turned off.  
1. Unplug the power cable.  
2. Disconnect any other cables.  
3. Retract adjustable tilt foot if extended.  
4. Cover the lens with the lens cap.  
5. Put the projector and accessories in the supplied soft case.  
Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from  
damage.  
NOTE: The NP610S, the NP510WS, the NP405, and the NP305 do not come with a soft case.  
Insert the projector with the lens  
facing upward  
NOTE: When placing the projector in the soft case, retract the tilt foot and the rear feet. Failure to do so may case damage to the  
projector.  
CAUTION:  
Use caution when putting the projector in the soft case immediately after the projector has been operating. The  
projector cabinet is hot.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
1 Turning off the Image and Sound  
OFF  
ON  
POWER  
Press the AV-MUTE button to turn off the image and sound for a short  
MAGNIFY AV-MUTE  
PAGE  
UP  
period of time. Press again to restore the image and sound.  
DOWN  
MENU  
ENTER  
NOTE:  
Even though the image is turned off, the menu still remains on the screen.  
• Sound from the AUDIO OUT jack (Stereo mini) can be turned off.  
EXIT  
S-VIDEO  
ECO MODE  
HELP  
2
Freezing a Picture  
VOLUME ASPECT  
Press the FREEZE button to freeze a picture. Press again to resume  
PICTURE FREEZE  
motion.  
NOTE: The image is frozen but the original video is still playing back.  
Enlarging a Picture  
You can enlarge the picture up to four times.  
NOTE: The maximum magnification may be less than four times depending on  
the signal.  
To do so:  
1. Press the MAGNIFY (+) button to magnify the picture.  
To move the magnified image, use the ,,or button.  
OFF  
ON  
POWER  
MAGNIFY AV-MUTE  
PAGE  
UP  
DOWN  
MENU  
ENTER  
EXIT  
OFF  
ON  
POWER  
MAGNIFY AV-MUTE  
PAGE  
UP  
DOWN  
MENU  
ENTER  
EXIT  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
4. Convenient Features  
2. Press the  button.  
The area of the magnified image will be moved  
3. Press the MAGNIFY (−) button.  
OFF  
ON  
POWER  
Each time the MAGNIFY (−) button is pressed, the image is re-  
duced.  
MAGNIFY AV-MUTE  
PAGE  
UP  
DOWN  
NOTE:  
M
ENTER  
• The image will be enlarged or reduced at the center of the screen.  
• Displaying the menu will cancel the current magnification.  
EXIT  
Changing Eco Mode  
This feature enables you to select two brightness modes of the lamp:  
OFF and ON modes. The lamp life can be extended by turning on the [ECO MODE].  
[ECO MODE]  
[OFF]  
Description  
Status of LAMP indicator  
Off  
This is the default setting (100% Brightness).  
LAMP  
STATUS  
[ON]  
Select this mode to increase the lamp life (approx. Steady Green light  
70% Brightness on NP610/NP510W/NP410W/  
NP610S/NP510WS and approx. 80% Brightness on  
NP510/NP410/NP405/NP310/NP305).  
LAMP  
STATUS  
To turn on the [ECO MODE], do the following:  
1. Press the ECO MODE button on the remote control to display [ECO MODE] screen.  
2. Use the or button to select [ON].  
3. Press the ENTER button.  
To change from [ON] to [OFF], Go back to Step 2 and select [OFF]. Repeat Step 3.  
NOTE:  
• The [ECO MODE] can be changed by using the menu.  
Select [SETUP] [GENERAL] [ECO MODE].  
• The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] [USAGE TIME].  
• The projector is always in [ON] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green. The  
lamp condition will not be affected even when [ECO MODE] is changed.  
• After a lapse of 1 minute from when the projector displays a blue, black or logo screen, [ECO MODE] will automatically switch to  
[ON]. The projector will return to the [OFF] once a signal is accepted.  
• If the projector is overheated in [OFF] mode, there may be a case where the [ECO MODE] automatically changes to [ON] mode  
to protect the projector. When the projector is in [ON] mode, the picture brightness decreases. When the projector comes back  
to normal temperature, the [ECO MODE] returns to [OFF] mode.  
Thermometer symbol [ ] indicates the [ECO MODE] is automatically set to [ON] mode because the internal temperature is too  
high.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Convenient Features  
Checking Energy-Saving Effect [CARBON METER]  
This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO MODE]  
is set to [ON]. This feature is called as [CARBON METER].  
There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON  
SAVINGS] message shows the total amount of CO2 emission reduction from the time of shipment up to now.You can  
check the information on [USAGE TIME] from [INFO.] of the menu. (page 78)  
The [CARBON SAVINGS-SESSION] message shows the amount of CO2 emission reduction between the time of  
changing to ECO MODE immediately after the time of power-on and the time of power-off. The [CARBON SAVINGS-  
SESSION] message will be displayed in the [POWER OFF/ ARE YOU SURE?] message at the time of power-off.  
TIP:  
• The formula as shown below is used to calculate the amount of CO2 emission reduction.  
Amount of CO2 emission reduction = Power consumption in OFF for ECO MODE – Power consumption in ON for ECO MODE x  
CO2 conversion factor.*  
* Calculation for amount of CO2 emission reduction is based on an OECD publication “CO2 Emissions from Fuel Combustion,  
2008 Edition”.  
• This formula will not apply to the power consumption which is not affected by whether [ECO MODE] is turned on or off.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
Preventing the Unauthorized Use of the Projector [SECURITY]  
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword  
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro-  
jector cannot project an image.  
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.  
To enable the Security function:  
1. Press the MENU button.  
The menu will be displayed.  
2. Press the button twice to select [SETUP] and press the button or the ENTER button to select [GEN-  
ERAL].  
3. Press the button to select [INSTALLATION].  
4. Press the button three times to select [SECURITY] and press the ENTER button.  
The OFF/ON menu will be displayed.  
5. Press the button to select [ON] and press the ENTER button.  
The [SECURITY KEYWORD] screen will be displayed.  
6. Type in a combination of the four  buttons and press the ENTER button.  
NOTE: A keyword must be 4 to 10 digits in length.  
The [CONFIRM KEYWORD] screen will be displayed.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Convenient Features  
7. Type in the same combination of  buttons and press the ENTER button.  
The confirmation screen will be displayed.  
8. Select [YES] and press the ENTER button.  
The SECURITY function has been enabled.  
To turn on the projector when [SECURITY] is enabled:  
1. Press and hold the POWER button for about 1 second.  
The projector will be turned on and display a message to the effect that the projector is locked.  
2. Press the MENU button.  
3. Type in the correct keyword and press the ENTER button.The projector will display an image.  
NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cable.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
To disable the SECURITY function:  
1. Press the MENU button.  
The menu will be displayed.  
2. Select [SETUP] [INSTALLATION] [SECURITY] and press the ENTER button.  
The OFF/ON menu will be displayed.  
3. Select [OFF] and press the ENTER button.  
The KEYWORD CONFIRMATION screen will be displayed.  
4. Type in your keyword and press the ENTER button.  
When the correct keyword is entered, the SECURITY function will be disabled.  
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request  
code. Your request code is displayed in the Keyword Confirmation screen. In this example [K992-45L8-JNGJ-4XU9-1YAT-EEA2] is  
a request code.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
7 Using the Optional Remote Mouse Receiver (NP01MR)  
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.  
It is a great convenience for clicking through your computer-generated presentations.  
Connecting the remote mouse receiver to your computer  
If you wish to use the remote mouse function, connect the mouse receiver and computer.  
The mouse receiver can be connected directly to the computer’s USB port (type A).  
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change  
your computer settings.  
Computer  
Remote mouse receiver  
To USB port of PC or Macintosh  
When operating a computer via the remote mouse receiver  
7m/22 feet  
30˚  
30˚  
Remote sensor on the  
remote mouse receiver  
When connecting using the USB terminal  
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000, Windows Vista, or Mac OS  
X 10.0.0 or later operating system.  
* NOTE: In SP1 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:  
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer  
Options tab].  
NOTE: The PAGE UP and DOWN buttons do not work with PowerPoint for Macintosh.  
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not  
identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Convenient Features  
Operating your computer’s mouse from the remote control  
You can operate your computer’s mouse from the remote control.  
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in Power-  
Point on your computer.  
 Buttons:  
moves the mouse cursor on your computer.  
MOUSE L-CLICK Button: works as the mouse left button.  
MOUSE R-CLICK Button: works as the mouse right button.  
NOTE:  
• When you operate the computer using the  or button with the menu displayed, both the menu and the mouse pointer  
will be affected. Close the menu and perform the mouse operation.  
• The PAGE UP and DOWN buttons do not work with PowerPoint for Macintosh.  
About Drag Mode:  
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and the  
drag operation can be performed simply by pressing the  button.To drop the item, press the MOUSE L-CLICK  
(or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.  
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user  
documentation or online help supplied with your computer.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
Network Setting by Using an HTTP Browser (except NP405  
and NP305)  
Overview  
Connecting the projector to a network allows the Alert Mail setting (page 50) and the projector control from a  
computer via the network.  
To perform the projector control from a web browser, you must have an exclusive application installed on your com-  
puter.  
The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser by  
using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web  
browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The  
setting method will vary depending on the version of browser. Please refer to the help files and the other information  
provided in your software.)  
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected  
to the projector and enter the following URL.  
Network Setting  
http://<the projector’s IP address>/index.html  
Alert Mail Setting  
http://<the projector’s IP address>/lanconfig.html  
TIP:  
• The default IP address is “192.168.0.10”.  
• The exclusive application can be downloaded from our website.  
NOTE:  
• If the PROJECTOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web  
browser (or clear the cache).  
• The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your network.  
Should this happen, consult your network administrator.  
The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and  
repeat. If you still can’t get any response, turn off and back on the projector.  
Preparation Before Use  
Connect the projector to a commercially available LAN cable before engaging in browser operations. (page 24)  
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the  
setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set  
will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be  
reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.  
Handling of the Address for Operation via a Browser  
Regarding the actual address that is entered for the address or entered to the URL column when operation of the pro-  
jector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the  
projector has been registered to the domain name server by a network administrator, or the host name corresponding  
to the IP address of the projector has been set in the “HOSTS” file of the computer being used.  
Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network  
setting by specifying  
http://pj.nec.co.jp/index.html  
for the address or the entry column of the URL.  
Example 2: When the IP address of the projector is “192.168.73.1”, access is gained to the mail alert settings by  
specifying  
http://192.168.73.1/index.html  
for the address or the entry column of the URL.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Convenient Features  
Network Settings  
http://<the projector’s IP address> /index.html  
DHCP..................................Enabling this option automatically assigns an IP address to the projector from your DHCP server.  
Disabling this option allows you to register the IP address or subnet mask number obtained from  
your network administrator.  
TIP: You can check the IP address in the menu when [ENABLE] is selected for [DHCP]. To do so,  
from the menu, select [INFO.] [WIRED LAN].  
IP ADDRESS.......................Set your IP address of the network connected to the projector when [DISABLE] is selected for  
[DHCP].  
TIP: You can check your specified IP address in the menu. To do so, from the menu, select [INFO.]  
[WIRED LAN].  
SUBNET MASK...................Set your subnet mask number of the network connected to the projector when [DISABLE] is selected  
for [DHCP].  
DEFAULT GATEWAY................Set your default gateway of the network connected to the projector when [DISABLE] is selected for  
[DHCP].  
DNS (PRIMARY).................Set your primary DNS settings of the network connected to the projector.  
DNS (SECONDARY) .................Set your secondary DNS settings of the network connected to the projector.  
UPDATE..............................Reflect your settings.  
NOTE: Close the browser after clicking [UPDATE]. The projector will automatically update your  
settings.  
TIP: Selecting [NETWORK SETTINGS] for [RESET] from the projector’s menu allows you to return the following items to the factory  
default.  
[DHCP]: DISABLE  
[IP ADDRESS]: 192.168.0.10  
[SUBNET MASK]: 255.255.255.0  
[DEFAULT GATEWAY]: 192.168.0.1  
* [DNS(PRIMARY)] and [DNS(SECONDARY)] will remain unchanged.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
Alert Mail Setting  
http://<the projector’s IP address>/lanconfig.html  
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification  
will be sent when the projector lamp has reached the end of its usable life or an error occurs in the projector.  
HOST NAME ............................ Type in the hostname of the network connected to the projector. Up to 60 alphanumeric char-  
acters can be used. If the host name is unknown, type in a string of characters representing the  
projector. Example: Projector 1  
DOMAIN NAME ........................ Type in the domain name of the network connected to the projector. Up to 60 alphanumeric  
characters can be used. If the domain name is unknown, type in the right side of @ in the sender’s  
address. Example: nec. com  
ALERT MAIL ............................. Checking [ENABLE] will turn on the Alert Mail feature.  
Checking [DISABLE] will turn off the Alert Mail feature.  
SENDER’S ADDRESS................ Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.  
SMTP SERVER NAME............... Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters  
can be used.  
RECIPIENT’S ADDRESS 1 to 3.... Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.  
APPLY....................................... Click this button to reflect the above settings  
EXECUTE .................................. Click this button to send a test mail to check if your settings are correct.  
STATUS..................................... A reply to a test mail will be displayed.  
NOTE:  
• If you execute a test, you may not receive an Alert mail. Should this happen, check if the network settings are correct.  
• If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient ’s Ad-  
dress is correct  
TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
9 Using the VGA Signal Cable to Operate the Projector  
(Virtual Remote)  
Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote  
screen (or toolbar) can be displayed on your computer screen.  
This will help you perform operations such as projector’s power on or off and signal selection via the VGA signal  
cable.  
Virtual Remote screen  
Toolbar  
This section provides an outline of preparation for use of Virtual Remote Tool.  
For information on how to use Virtual Remote Tool, see Help of Virtual Remote Tool. (page 55)  
Step 1: Install Virtual Remote Tool on the computer. (page 51, 52)  
Step 2: Connect the projector to the computer. (page 53)  
Step 3: Start Virtual Remote Tool. (page 54)  
NOTE:  
• When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well  
as your computer screen.  
• Use the supplied VGA signal cable to connect the COMPUTER 1 IN connector directly with the monitor output connector of the  
computer to use Virtual Remote Tool.  
Using a switcher or other cables than the supplied VGA signal cable may cause failure in signal communication.  
VGA cable connector:  
Pin Nos. 12 and 15 are required for DDC/CI.  
• Virtual Remote Tool may not work depending on your computer’s specifications and version of graphic adapters or drivers.  
TIP:  
• The projector’s COMPUTER 1 IN connector supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard  
interface for bidirectional communication between display/projector and computer.  
• For update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl/en/index.html  
Step 1: Install Virtual Remote Tool on the computer  
Supported OS  
Virtual Remote Tool will run on the following operating systems.  
Windows Vista Home Basic *1, Windows Vista Home Premium *1, Windows Vista Business *1,  
Windows Vista Enterprise *1, Windows Vista Ultimate *1  
Windows XP Home Edition *2, Windows XP Professional *2, Windows 2000 Professional *2  
*1: Supports 32-bit version.  
*2: To run Virtual Remote Tool, “Microsoft .NET Framework Version 2.0 or later” is required. The Microsoft .NET  
Framework Version 2.0 or later is available from Microsoft’s web page. Install the Microsoft .NET Framework  
Version 2.0 or later on your computer. Windows 2000 Professional supports Microsoft .NET Framework Ver-  
sion 2.0 only.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. Convenient Features  
Install Virtual Remote Tool  
Preparation:  
Exit all running programs before installing Virtual Remote Tool. If another program is running, the installation may not  
be completed.To install Virtual Remote Tool, the Windows user account must have [Administrator] privilege (Windows  
Vista and Windows 2000) or [Computer Administrator] privilege (Windows XP).  
1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.  
The folders in NEC Projector CD-ROM will be displayed. If the folders are not displayed, right-click the CD/DVD  
drive icon in Windows’ “Computer” (or “My Computer”) and select “Open”.  
2 Double-click “software” and then “Virtual Remote Tool”.  
The “setup.exe” icon will be displayed.  
3 Double-click the “setup.exe” icon.  
The Installer will start and the Wizard screen will appear.  
4 Click “Next”.  
“END USER LICENSE AGREEMENT” screen will be displayed.  
Read “END USER LICENSE AGREEMENT” carefully.  
5 If you agree, click “I accept the terms in the license agreement” and then click “Next”.  
Follow the instructions on the installer screens to complete the installation.  
After the installation is completed, the shortcut icon  
for Virtual Remote Tool will be placed on the desktop.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
TIP:  
Uninstalling Virtual Remote Tool  
Preparation:  
Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote Tool, the Windows user account must have  
“Administrator” privilege (Windows Vista and Windows 2000) or “Computer Administrator” privilege (Windows XP).  
• For Windows Vista  
1 Click “Start” and then “Control Panel”.  
The Control Panel window will be displayed.  
2 Click “Uninstall a program” under “Programs”  
The “Programs and Features” window will be displayed.  
3 Select Virtual Remote Tool and click it.  
4 Click “Uninstall/Change” or “Uninstall”.  
• When the “User Account Control” windows is displayed, click “Continue”.  
Follow the instructions on the screens to complete the uninstallation.  
• For Windows XP/2000  
1 Click “Start” and then “Control Panel”.  
The Control Panel window will be displayed.  
2 Double-click “Add / Remove Programs”.  
The Add / Remove Programs window will be displayed.  
• On Windows 2000, double-click “Uninstall a program”.  
3 Click Virtual Remote Tool from the list and then click “Remove”.  
Follow the instructions on the screens to complete the uninstallation.  
Step 2: Connect the projector to the computer  
1 Use the suppliedVGA signal cable to connect the COMPUTER 1 IN connector of the projector directly with  
the monitor output connector of the computer.  
2 Connect the supplied power cable to the AC IN of the projector and the wall outlet, and then press the Main  
Power switch to turn on the main power.  
The projector is in the standby condition.  
VGA signal cable (supplied)  
COMPUTER 1 IN  
To wall outlet  
AC Input  
Main Power Switch  
Power cable (supplied)  
TIP:  
• When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed to navigate your connections.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
Step 3: Start Virtual Remote Tool  
1 Double-click the shortcut icon  
on the Windows Desktop.  
When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.  
Follow the instructions on the screens  
When “Easy Setup” is completed, the Virtual Remote Tool screen will be displayed.  
TIP:  
• The Virtual Remote Tool screen (or Toolbar) can be displayed without displaying “Easy Setup” window.  
To do so, click to place a check mark for “ Do not use Easy Setup next time” on the screen at Step 6 in “Easy Setup”.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Convenient Features  
Exiting Virtual Remote Tool  
1 Click the Virtual Remote Tool icon  
The pop-up menu will be displayed.  
on the Taskbar.  
2 Click “Exit”.  
The Virtual Remote Tool will be closed.  
Viewing the help file of Virtual Remote Tool  
• Displaying the help file using the taskbar  
1 Click the Virtual Remote Tool icon  
on the taskbar when Virtual Remote Tool is running.  
The pop-up menu will be displayed.  
2. Click “Help”.  
The Help screen will be displayed.  
• Displaying the help file using the Start Menu.  
1. ClickStart”.“All programsorPrograms”.NEC Projector User Supportware”.Virtual RemoteTool”. and  
then “Virtual Remote Tool Help” in this order.  
The Help screen will be displayed.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
1 Using the Menus  
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.  
1. Press the MENU button on the remote control or the projector cabinet to display the menu.  
NOTE: The commands such as ENTER, EXIT, ,  in the bottom show available buttons for your operation.  
2. Press the  buttons on the remote control or the projector cabinet to display the submenu.  
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first  
tab.  
4. Use the  buttons on the remote control or the projector cabinet to select the item you want to adjust or  
set.  
You can use the  buttons on the remote control or the projector cabinet to select the tab you want.  
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.  
6. Adjust the level or turn the selected item on or off by using the  buttons on the remote control or  
the projector cabinet.  
Changes are stored until adjusted again.  
7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the projec-  
tor cabinet to quit the menu display.  
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.  
8. Press the MENU button to close the menu.  
To return to the previous menu, press the EXIT button.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
Menu Elements  
Tab  
Slide bar  
Solid triangle  
Available buttons  
Source  
Highlight  
Radio button  
High Altitude symbol  
Thermometer symbol  
Key Lock symbol  
Off Timer remaining  
time  
Menu windows or dialog boxes typically have the following elements:  
Highlight.............................Indicates the selected menu or item.  
Solid triangle ......................Indicates further choices are available. A highlighted triangle indicates the item is active.  
Tab......................................Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.  
Radio button.......................Use this round button to select an option in a dialog box.  
Source ................................Indicates the currently selected source.  
Off Timer remaining time....Indicates the remaining countdown time when the [OFF TIMER] is preset.  
Slide bar .............................Indicates settings or the direction of adjustment.  
Key Lock symbol ................Indicates the [CONTROL PANEL LOCK] is enabled.  
Thermometer symbol .........Indicates the [ECO MODE] is forcibly set to [ON] mode because the internal temperature is too  
high.  
High Altitude symbol ..........Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
List of Menu Items  
Some menu items are not available depending on the input source.  
Menu Item  
Default  
Options  
COMPUTER1  
COMPUTER2(DIGITAL)*1  
COMPUTER2(ANALOG)*1  
VIDEO  
*
*
*
*
*
*
SOURCE  
S-VIDEO  
PRESET  
1–6  
GENERAL  
HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE,  
GRAPHIC, sRGB  
REFERENCE  
*
GAMMA  
CORRECTION  
COLOR  
TEMPERATURE  
DYNAMIC  
CONTRAST*2  
IMAGE MODE  
WHITE  
DYNAMIC, NATURAL, BLACK DETAIL  
*
5000, 6500, 7800, 8500, 9300, 10500  
*
*
OFF, ON  
STILL, MOVIE  
DETAIL  
SETTINGS  
BALANCE  
CONTRAST R  
CONTRAST G  
CONTRAST B  
BRIGHTNESS  
R
0
0
0
PICTURE  
0
0
0
BRIGHTNESS  
G
BRIGHTNESS  
B
ADJUST  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
HUE  
RESET  
CLOCK  
PHASE  
HORIZONTAL  
VERTICAL  
OVERSCAN  
*
*
*
*
*
IMAGE  
0[%], 5[%], 10[%]  
NP610/NP510/NP410/NP405/NP310/NP305/NP610S:  
AUTO, 4:3, 16:9, 15:9, 16:10, WIDE ZOOM, NATIVE  
NP510W/NP410W/NP510WS: AUTO, 4:3, 16:9, 15:9,  
16:10, LETTERBOX, NATIVE  
OPTIONS  
*
*
ASPECT RATIO  
POSITION  
0
(Not available on NP510W/NP410W/NP510WS)  
80–100  
OFF, ON  
DIGITAL ZOOM*3  
AUTO KEYSTONE  
KEYSTONE  
100  
OFF  
0
KEYSTONE SAVE  
OFF  
OFF, ON  
OFF, WHITEBOARD, BLACKBOARD, BLACKBOARD  
(GRAY), LIGHT YELLOW, LIGHT GREEN, LIGHT  
BLUE, SKY BLUE, LIGHT ROSE, PINK  
OFF, ON  
OFF, CAPTION1, CAPTION2, CAPTION3, CAPTION4,  
TEXT1, TEXT2, TEXT3, TEXT4  
WALL COLOR  
ECO MODE  
OFF  
OFF  
OFF  
GENERAL  
CLOSED CAPTION  
ENGLISH, DEUTSCH, FRANÇAIS, ITALIANO,  
ESPAÑOL, SVENSKA, 日本語  
SETUP  
DANSK, PORTUGUÊS, ČEŠTINA, MAGYAR, POLSKI,  
NEDERLANDS, SUOMI  
LANGUAGE  
ENGLISH  
NORSK, TÜRKÇE, РУССКИЙ,  
국어  
, Ελληνικά, 中文, 한  
COLOR SELECT  
SOURCE DISPLAY  
ID DISPLAY  
COLOR  
ON  
ON  
COLOR, MONOCHROME  
OFF, ON  
OFF, ON  
MENU  
ECO MESSAGE  
DISPLAY TIME  
BACKGROUND  
FILTER MESSAGE  
OFF  
OFF, ON  
AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC  
BLUE  
500[H]  
BLUE, BLACK, LOGO  
OFF, 100[H], 200[H], 500[H], 1000[H]  
*
The asterisk (*) indicates that the default setting varies depending on the signal.  
*1: COMPUTER 2(DIGITAL) is not available on NP405 and NP305. The source for the computer 2 analog signal is displayed as “COMPUTER2” on  
NP405 and NP305.  
*2: DYNAMIC CONTRAST is available on NP410 and NP310 only.  
*3: DIGITAL ZOOM is available on NP610S and NP510WS only.  
*4: Wired LAN is not supported by NP405 and NP305.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
DESKTOP  
FRONT  
OFF  
DESKTOP FRONT, CEILING REAR, DESKTOP REAR,  
CEILING FRONT  
OFF, ON  
ORIENTATION  
CONTROL PANEL LOCK  
SECURITY  
OFF  
OFF, ON  
INSTALLATION  
COMMUNICATION SPEED  
19200bps  
4800bps, 9600bps, 19200bps  
CONTROL ID  
NUMBER  
1
1–254  
CONTROL ID  
CONTROL ID  
OFF  
NORMAL  
AUTO  
OFF, ON  
OFF, NORMAL, FINE  
AUTO, HIGH, HIGH ALTITUDE  
AUTO ADJUST  
FAN MODE  
RGB/  
COMPONENT  
RGB/  
COMPUTER1  
RGB/COMPONENT, RGB, COMPONENT  
RGB/COMPONENT, RGB, COMPONENT  
COMPUTER2  
(ANALOG)*1  
SIGNAL  
SELECT  
COMPONENT  
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N,  
PAL60, SECAM  
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N,  
PAL60, SECAM  
VIDEO  
AUTO  
AUTO  
SETUP  
S-VIDEO  
OPTIONS(1)  
NP610/NP510/  
NP410/NP405/  
NP310/NP305/  
WXGA MODE  
NP610S: OFF OFF, ON  
NP510W/  
NP410W/  
NP510WS: ON  
DEINTERLACE  
BEEP  
ON  
ON  
OFF, ON  
OFF, ON  
OFF TIMER  
STANDBY MODE  
AUTO POWER ON(AC)  
AUTO POWER ON(COMP1)  
AUTO POWER OFF  
OFF  
NORMAL  
OFF  
OFF  
OFF  
OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00  
NORMAL, POWER-SAVING  
OFF, ON  
OPTIONS(2)  
USAGE TIME  
OFF, ON  
OFF, 0:05, 0:10, 0:20, 0:30  
LAST, AUTO, COMPUTER1, COMPUTER2(DIGITAL)*1,  
COMPUTER2(ANALOG), VIDEO, S-VIDEO  
DEFAULT SOURCE SELECT  
LAST  
LAMP LIFE REMAINING  
LAMP HOURS USED  
FILTER HOURS USED  
TOTAL CARBON SAVINGS  
SOURCE NAME  
SOURCE INDEX  
HORIZONTAL FREQUENCY  
VERTICAL FREQUENCY  
SIGNAL TYPE  
SOURCE  
VIDEO TYPE  
SYNC TYPE  
SYNC POLARITY  
SCAN TYPE  
INFO.  
PROJECTOR NAME  
IP ADDRESS  
SUBNET MASK  
GATEWAY  
MAC ADDRESS  
PRODUCT  
SERIAL NUMBER  
FIRMWARE  
WIRED LAN*4  
VERSION  
DATA  
CONTROL ID (when [CONTROL  
ID] is set)  
CURRENT SIGNAL  
ALL DATA  
RESET  
NETWORK SETTINGS*4  
CLEAR LAMP HOURS  
CLEAR FILTER HOURS  
*
The asterisk (*) indicates that the default setting varies depending on the signal.  
*1: COMPUTER 2(DIGITAL) is not available on NP405 and NP305. The source for the computer 2 analog signal is displayed as “COMPUTER2” on  
NP405 and NP305.  
*2: DYNAMIC CONTRAST is available on NP410 and NP310 only.  
*3: DIGITAL ZOOM is available on NP610S and NP510WS only.  
*4: Wired LAN is not supported by NP405 and NP305.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Menu  
Menu Descriptions & Functions [SOURCE]  
[NP610/NP510/NP410/NP310/NP510W/NP410W/  
NP610S/NP510WS]  
[NP405/NP305]  
COMPUTER1  
Selects the computer connected to your COMPUTER 1 IN input connector.  
NOTE:  
• When the component input signal is connected to the COMPUTER 1 IN connector, select [COMPUTER1].  
• The projector will determine if the input signal is RGB or component signal.  
COMPUTER2 (DIGITAL & ANALOG)  
Selects the computer connected to your COMPUTER 2 IN (DVI-I) connector.  
COMPUTER2 (NP405 and NP305 only)  
Selects the computer connected to your COMPUTER2 IN connector.  
VIDEO  
Selects what is connected to your VIDEO input-VCR, DVD player or document camera.  
S-VIDEO  
Selects what is connected to your S-VIDEO input-VCR or DVD player.  
NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S-  
Video source.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Menu Descriptions & Functions [ADJUST]  
[PICTURE]  
[PRESET]  
This function allows you to select optimized settings for your projected image.  
You can adjust neutral tint for yellow, cyan or magenta.  
There are six factory presets optimized for various types of images.You can also use [DETAIL SETTINGS] to set user  
adjustable settings to customize each gamma or color.  
Your settings can be stored in [PRESET 1] to [PRESET 6].  
HIGH-BRIGHT........ Recommended for use in a brightly lit room.  
PRESENTATION..... Recommended for making a presentation using a PowerPoint file.  
VIDEO.................... Recommended for typical TV program viewing.  
MOVIE ................... Recommended for movies.  
GRAPHIC............... Recommended for graphics.  
sRGB ..................... Standard color values  
[DETAIL SETTINGS]  
[NP610/NP510/NP405/NP305/NP510W/NP410W/  
NP610S/NP510WS]  
[NP410/NP310]  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
[GENERAL]  
Storing Your Customized Settings [REFERENCE]  
This function allows you to store your customized settings in [PRESET 1] to [PRESET 6].  
First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERA-  
TURE].  
HIGH-BRIGHT........ Recommended for use in a brightly lit room.  
PRESENTATION..... Recommended for making a presentation using a PowerPoint file.  
VIDEO.................... Recommended for typical TV program viewing.  
MOVIE ................... Recommended for movies.  
GRAPHIC............... Recommended for graphics.  
sRGB ..................... Standard color values.  
Selecting Gamma Correction Mode [GAMMA CORRECTION]  
Each mode is recommended for:  
DYNAMIC .............. Creates a high-contrast picture.  
NATURAL............... Natural reproduction of the picture.  
BLACK DETAIL....... Emphasizes detail in dark areas of the picture.  
Adjusting Color Temperature [COLOR TEMPERATURE]  
This option allows you to select the color temperature of your choice.  
NOTE: When [PRESENTATION] or [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available.  
Adjusting Brightness and Contrast [DYNAMIC CONTRAST] (NP410 and NP310)  
This function allows you to adjust the contrast ratio optically using the built-in iris.  
To increase the contrast ratio, select [ON].  
Selecting Still Image Mode or Movie Mode [IMAGE MODE]  
This function allows you to select the still image mode or the movie mode.  
STILL..................... This mode is for a still image.  
MOVIE ................... This mode is for a movie.  
NOTE: This function is available only when [HIGH-BRIGHT] is selected for [REFERENCE].  
Adjusting White Balance [WHITE BALANCE]  
This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen;  
Brightness for each color (RGB) is used to adjust the black level of the screen.  
[CONTRAST]  
Adjusts the intensity of the image according to the incoming signal.  
[BRIGHTNESS]  
Adjusts the brightness level or the back raster intensity.  
[SHARPNESS]  
Controls the detail of the image.  
[COLOR]  
Increases or decreases the color saturation level.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
[HUE]  
Varies the color level from +/− green to +/− blue. The red level is used as reference.  
Input signal  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
No  
HUE  
No  
Computer (RGB DIGITAL)  
Computer (RGB ANALOG)  
Component  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
Yes*  
Yes  
Yes*  
Yes  
Video, S-Video  
Yes = Adjustable, No = Not adjustable, Yes* = depending on the signal  
NOTE: The NP405 and NP305 do not support “Computer (RGB DIGITAL)” signal.  
[RESET]  
The settings and adjustments for [CONTRAST], [BRIGHTNESS], [SHARPNESS], [COLOR], [HUE], and [REFER-  
ENCE] within [PRESET] will be returned to the factory settings.  
The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently selected  
will not be reset.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
[IMAGE OPTIONS]  
Adjusting Clock and Phase [CLOCK/PHASE]  
This allows you to manually adjust CLOCK and PHASE.  
CLOCK................... Use this item to fine tune the computer image or to remove any vertical banding that might appear. This  
function adjusts the clock frequencies that eliminate the horizontal banding in the image.  
This adjustment may be necessary when you connect your computer for the first time.  
PHASE................... Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is  
evident when part of your image appears to be shimmering.)  
Use [PHASE] only after the [CLOCK] is complete.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL]  
Adjusts the image location horizontally and vertically.  
-
-
An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction.  
The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the  
current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency,  
its adjustments will be called up and applied.  
To delete adjustments stored in memory, from the menu, you select [RESET] [CURRENT SIGNAL] or [ALL  
DATA] and reset the adjustments.  
Selecting Overscan Percentage [OVERSCAN]  
Select overscan percentage (0%, 5% and 10%) for signal.  
Projected image  
Overscaned by 10%  
NOTE:  
• The [0[%]] cannot be selected when VIDEO and S-VIDEO signals are used.  
• [OVERSCAN] is not available when [NATIVE] is selected for [ASPECT RATIO].  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Selecting Aspect Ratio [ASPECT RATIO]  
The term “aspect ratio” refers to the ratio of width to height of a projected image.  
The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio.  
• This table shows typical resolutions and aspect ratios that most computers support.  
Resolution  
640 x 480  
Aspect Ratio  
4:3  
VGA  
SVGA  
XGA  
WXGA  
WXGA  
WXGA+  
SXGA  
SXGA+  
UXGA  
800 x 600  
1024 x 768  
1280 x 768  
1280 x 800  
1440 x 900  
1280 x 1024  
1400 x 1050  
1600 x 1200  
4:3  
4:3  
15:9  
16:10  
16:10  
5:4  
4:3  
4:3  
Options  
Function  
AUTO  
The projector will automatically determine the incoming signal and display it in its aspect  
ratio. (next page)  
The projector may erroneously determine the aspect ratio depending on its signal. If this  
occurs, select the appropriate aspect ratio from the following.  
The image is displayed in 4:3 aspect ratio.  
4:3  
16:9  
15:9  
16:10  
The image is displayed in 16:9 aspect ratio.  
The image is displayed in 15:9 aspect ratio.  
The image is displayed in 16:10 aspect ratio.  
WIDE ZOOM  
The image is stretched left and right.  
(NP610/NP510/NP410/  
NP405/NP310/NP305/  
NP610S)  
Parts of the displayed image are cropped at the left and right edges and therefore not  
visible.  
LETTERBOX  
The image of a letterbox signal is stretched equally in the horizontal and vertical directions  
to fit the screen. Parts of the displayed image are cropped at the top and bottom edges  
and therefore not visible.  
The projector displays the current image in its true resolution when the incoming computer  
signal has a lower resolution than the projector’s native resolution.  
(NP510W/NP410W/  
NP510WS)  
NATIVE  
[Example 1] When the incoming  
signal with the resolution of 800 x 600  
is displayed on the NP610/NP510/  
NP410/NP405/NP310/NP305/  
NP610S:  
[Example 2] When the incoming sig-  
nal with the resolution of 800 x 600 is  
displayed on the NP510W/NP410W/  
NP510WS:  
NOTE:  
• When a non-computer signal is displayed, the [NATIVE] is not available.  
• When a signal with a higher resolution than the projector’s native resolution is displayed, [NATIVE]  
is not available.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Sample image when the appropriate aspect ratio is automatically determined  
NP610/NP510/NP410/NP405/NP310/NP305/NP610S  
[Computer signal]  
Aspect ratio of incoming signal  
4:3  
5:4  
16:9  
15:9  
16:10  
Sample image when the appro-  
priate aspect ratio is automati-  
cally determined  
[Video signal]  
Aspect ratio of incoming signal  
4:3  
Letterbox  
Squeeze  
Sample image when the as-  
pect ratio is automatically de-  
termined  
NOTE: To display a squeezed signal prop-  
erly, select [16:9] or [WIDE ZOOM].  
NP510W/NP410W/NP510WS  
[Computer signal]  
Aspect ratio of incoming signal  
4:3  
4:3  
5:4  
16:9  
15:9  
16:10  
Sample image when the appro-  
priate aspect ratio is automati-  
cally determined  
[Video signal]  
Aspect ratio of incoming signal  
Letterbox  
Squeeze  
Sample image when the as-  
pect ratio is automatically de-  
termined  
NOTE: To display a letterbox signal prop- NOTE: To display a squeezed signal prop-  
erly, select [LETTERBOX]. erly, select [16:9].  
TIP:  
• Image position can be adjusted vertically using [POSITION] when the [16:9], [15:9], or [16:10] aspect ratios are selected.  
• The term “letterbox” refers to a more landscape-oriented image when compared to a 4:3 image, which is the standard aspect  
ratio for a vide source.  
The letterbox signal has aspect ratios with the vista size “1.85:1” or cinema scope size “2.35:1” for movie film.  
• The term “squeeze” refers to the compressed image of which aspect ratio is converted from 16:9 to 4:3.  
Adjusting the Vertical Position of Image [POSITION] (not available on NP510W/NP410W/  
NP510WS)  
(only when [16:9], [15:9], or [16:10] is selected for [ASPECT RATIO])  
When [16:9], [15:9], or [16:10] is selected in [ASPECT RATIO], the image is displayed with black borders on the top  
and bottom.  
You can adjust the vertical position from the top to the bottom of the black area.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Menu Descriptions & Functions [SETUP]  
[GENERAL]  
[NP610/NP510/NP410/NP405/NP310/NP305/NP510W/  
NP410W]  
[NP610S/NP510WS]  
Using Digital Zoom [DIGITAL ZOOM] (NP610S/NP510WS)  
This feature allows you to electronically fine adjust the image size on the screen.  
Use or button to large or reduce the projected image.  
TIP:  
To adjust the projected image size roughly, move the projector away or closer to the screen. (page 30). To fine adjust the zoom,  
use the [DIGITAL ZOOM] function.  
Enabling Auto Keystone [AUTO KEYSTONE]  
This feature allows the projector to detect its tilt and correct vertical distortion automatically.  
To turn on the AUTO KEYSTONE feature, select [ON]. To adjust the KEYSTONE feature manually, select [OFF].  
Correcting Vertical Keystone Distortion Manually [KEYSTONE]  
You can correct vertical distortion manually. (page 34)  
TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.  
Saving Vertical Keystone Correction [KEYSTONE SAVE]  
This option enables you to save your current keystone settings.  
OFF ........................ Does not save current keystone correction settings. It will return your keystone correction settings to  
“zero”.  
ON ......................... Saves current keystone correction settings  
Saving your change once affects all sources. The changes are saved when the projector is turned off.  
NOTE: When [AUTO KEYSTONE] is set to [ON], [KEYSTONE SAVE] is not available. Next time you turn on the power, the AUTO  
KEYSTONE function will work and the data stored with [KEYSTONE SAVE] will be invalid.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
Using the Wall Color Correction [WALL COLOR]  
This function allows for quick adaptive color correction in applications where the screen material is not white.  
NOTE: Selecting [WHITEBOARD] reduces lamp brightness.  
Setting Eco Mode [ECO MODE]  
This feature turns on or off the ECO mode. The lamp life can be extended by selecting [ON]. Selecting [ON] also  
decreases fan noise when compared to [OFF] mode.  
ECO MODE  
OFF  
Description  
Status of LAMP indicator  
Off  
This is the Default setting  
(100% Brightness).  
Select this mode to increase the lamp  
life (approx. 70% Brightness on NP610/  
ON  
NP510W/NP410W/NP610S/NP510WS Steady Green light  
and approx. 80% Brightness on NP510/  
NP410/NP405/NP310/NP305).  
NOTE:  
• The [LAMP LIFE REMAINING] and [LAMP HOURS USED] can be checked in [USAGE TIME]. Select [INFO.] [USAGE TIME].  
(page 78)  
• The projector is always in [ON] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green. The  
lamp condition will not be affected even when [ECO MODE] is changed.  
• If there is no signal for about one minute, the projector will display a blue, black or logo background (depending on setting) and  
go into [ON].  
The projector will return to the [OFF] mode once a signal is accepted.  
• If the projector becomes overheated in [OFF] mode because of use in a high-temperature room, there may be a case where the  
[ECO MODE] automatically changes to [ON] mode to protect the projector. This mode is called “forced ECO mode”. When the  
projector is in [ON] mode, the picture brightness decreases. The LAMP indicator’s steady light indicates the projector is in [ON]  
mode. When the projector comes back to normal temperature, the [ECO MODE] returns to [OFF] mode.  
Thermometer symbol [ ] indicates the [ECO MODE] is automatically set to [ON] mode because the internal temperature is too  
high.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
Setting Closed Caption [CLOSED CAPTION]  
This option sets several closed caption modes that allow text to be superimposed on the projected image of Video  
or S-Video.  
OFF ........................ This exits the closed caption mode.  
CAPTION 1-4 ......... Text is superimposed.  
TEXT 1-4................ Text is displayed.  
NOTE:  
• The closed caption is not available under the following conditions:  
- when messages or menus are displayed.  
- when an image is magnified, frozen, or muted.  
• Doing the following may cause portions of superimposed text or closed caption to be truncated.  
If this occurs, try to change correction amount or selection to place the superimposed text or closed caption within the  
screen.  
- Using the [DIGITAL ZOOM] or [KEYSTONE] function to correct the image excessively  
- Selecting [16:10] or [16:9] from [ASPECT RATIO]  
- Using the [POSITION] (not available on NP510W/NP410W/NP510WS)  
Selecting Menu Language [LANGUAGE]  
You can choose one of 21 languages for on-screen instructions.  
NOTE: Your setting will not be affected even when [RESET] is done from the menu.  
[MENU]  
Selecting Menu Color [COLOR SELECT]  
You can choose between two options for menu color: COLOR and MONOCHROME.  
Turning On / Off Source Display [SOURCE DISPLAY]  
This option turns on or off input name display such as COMPUTER 1, COMPUTER2(DIGITAL), COMPUTER 2(ANA-  
LOG), VIDEO, S-VIDEO and No Input to be displayed on the top right of the screen.  
On NP405/NP305, the input name will be displayed as COMPUTER 1, COMPUTER2, VIDEO, and S-VIDEO.  
Turning ON/OFF Control ID [ID DISPLAY]  
(Available only when the optional remote control NP02RC is used)  
ID DISPLAY ........... This option turns on or off the ID number which is displayed when the ID SET button on the remote control  
is pressed.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Turning On / Off Eco Message [ECO MESSAGE]  
This option turns on or off the following messages when the projector is turned on.  
The Eco Message prompts the user to save energy. When [OFF] is selected for [ECO MODE], you will get a message  
to prompt you to select [ON] for [ECO MODE].  
When [ON] is selected for [ECO MODE]  
To close the message, press any one of the buttons. The message will disappear if no button operation is done for  
30 seconds.  
When [OFF] is selected for [ECO MODE]  
Pressing the ENTER button will display the [ECO MODE] screen. (page 69)  
To close the message, press the EXIT button.  
Selecting Menu Display Time [DISPLAY TIME]  
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The  
preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the fac-  
tory preset.  
Selecting a Color or Logo for Background [BACKGROUND]  
Use this feature to display a blue/black screen or logo when no signal is available. The default background is  
[BLUE].  
NOTE: Your setting will not be affected even when [RESET] is done from the menu.  
Selecting Interval Time for Filter Message [FILTER MESSAGE]  
This option allows you to select the time preference between displaying the message for cleaning the filters. Clean  
the filter when you get the message “PLEASE CLEAN FILTER.(page 81)  
Five options are available: OFF, 100[H], 200[H], 500[H], 1000[H]  
The default setting is 500[H].  
NOTE: Your setting will not be affected even when [RESET] is done from the menu.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Menu  
[INSTALLATION]  
Selecting Projector Orientation [ORIENTATION]  
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection,  
desktop rear projection, and ceiling front projection.  
DESKTOP FRONT  
CEILING REAR  
DESKTOP REAR  
CEILING FRONT  
Disabling the Cabinet Buttons [CONTROL PANEL LOCK]  
This option turns on or off the CONTROL PANEL LOCK function.  
NOTE:  
• This CONTROL PANEL LOCK does not affect the remote control functions.  
• When the control panel is locked, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will change  
the setting to [OFF].  
TIP: When the [CONTROL PANEL LOCK] is turned on, a key lock icon [  
] will be displayed at the bottom right of the menu.  
Enabling Security [SECURITY]  
This feature turns on or off the SECURITY function.  
Unless the correct keyword is entered, the projector cannot project an image. (page 43)  
NOTE: Your setting will not be affected even when [RESET] is done from the menu.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
Selecting Communication Speed [COMMUNICATION SPEED]  
This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 19200 bps.The  
default is 19200 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equip-  
ment, a lower baud rate may be recommended for long cable runs).  
NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.  
Setting ID to the Projector [CONTROL ID]  
(Available only when the optional remote control NP02RC is used)  
You can operate multiple projectors separately and independently with the single remote control that has the CONTROL  
ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together  
using the single remote control. To do so, you have to assign an ID number to each projector.  
CONTROL ID NUMBER.......Select a number from 1 to 254 you wish to assign to your projector.  
CONTROL ID.......................Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set-  
ting.  
NOTE:  
• Selecting [ON] for [CONTROL ID] will make the remote control supplied with the projector inoperable. The buttons on the projector  
cabinet can be used. Neither can you operate the projector by using the optional remote control NP01RC that does not has the  
CONTROL ID function.  
• Your setting will not be affected even when [RESET] is done from the menu.  
• Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control  
ID.  
L-CLICK  
R-CLICK  
Assigning or Changing the Control ID  
VOLUME  
MAGNIFY  
PAGE  
1. Turn on the projector.  
UP  
2. Press the ID SET button on the remote control (NP02RC).  
DOWN  
PICTURE  
AV-MUTE  
LAMP MODE  
3D REFORM  
ASPECT  
The CONTROL ID screen will be displayed.  
FREEZE  
HELP  
FOCUS  
LENS SHIFT /ZOOM  
If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the projector  
cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the inactive  
projector, assign the control ID used for the projector by using the following procedure (Step 3).  
3. Press one of numeric keypad buttons while pressing and holding the ID SET button on the remote control  
(NP02RC).  
Example:  
1
4
7
2
5
8
0
3
6
9
To assign “3”, press the “3” button on the remote control.  
No ID means that all the projectors can be operated together with a single remote  
control. To set “No ID”, enter “000” or press the CLEAR button.  
CLEAR  
ID  
L-CLICK  
R-CLICK  
TIP: The range of IDs is from 1 to 254.  
VOLUME  
MAGNIFY  
PAGE  
UP  
DOWN  
4. Release the ID SET button.  
PICTURE  
AV-MUTE  
LAMP MODE  
3D REFORM  
ASPECT  
FREEZE  
HELP  
The updated CONTROL ID screen will be displayed.  
NOTE: The IDs can be cleared in a few days after the batteries are run down or removed.  
FOCUS  
LENS SHIFT /ZOOM  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Menu  
[OPTIONS(1)]  
Setting Auto Adjust [AUTO ADJUST]  
This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for  
noise and stability.You can automatically make adjustment in two ways: [NORMAL] and [FINE].  
OFF ........................ The computer signal will not be automatically adjusted. You can manually optimize the computer signal.  
NORMAL................ Default setting. The computer signal will be automatically adjusted. Normally select this option.  
FINE....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when [NOR-  
MAL]is selected.  
Selecting Fan Mode [FAN MODE]  
This option allows you to select three modes for fan speed: Auto mode, High speed mode, and High Altitude mode.  
AUTO..................... The built-in fans automatically run at a variable speed according to the internal temperature.  
HIGH...................... The built-in fans run at high speed.  
HIGH ALTITUDE..... The built-in fans run at a high speed. Select this option when using the projector at altitudes approximately  
5500 feet/1600 meters or higher.  
When you wish to cool down the temperature inside the projector quickly, select [HIGH].  
NOTE:  
• It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.  
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or higher.  
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause  
the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.  
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the  
lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].  
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical components such  
as the lamp.  
• Your setting will not be affected even when [RESET] is done from the menu.  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Selecting Signal Format [SIGNAL SELECT]  
[COMPUTER1], [COMPUTER2(ANALOG)], [COMPUTER2 on NP405/NP305]  
Allows you to choose [COMPUTER1], or [COMPUTER2(ANALOG)] for an RGB source such as a computer, or  
[COMPONENT] for a component video source such as a DVD player. Normally select [RGB/COMPONENT] and the  
projector automatically detects a component signal. However there may be some component signals that the projector  
is unable to detect. If this is the case, select [COMPONENT].  
[VIDEO & S-VIDEO System Select]  
This feature enables you to select composite video standards automatically or manually.  
Normally select [AUTO] and the projector will automatically detect the video standard.  
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from  
the menu.  
This must be done for VIDEO and S-VIDEO respectively.  
Enabling or Disabling WXGA Mode [WXGA MODE]  
Selecting [ON] will give priority to a WXGA (1280 x 768) signal in recognizing an input signal.  
When [WXGA MODE] is set to [ON], an XGA (1024 x 768) signal may not be recognized on NP610, NP510, NP410,  
NP405, NP310, NP305, or NP610S. In this case, select [OFF].  
Enabling the deinterlace [DEINTERLACE]  
Turns on or off the deinterlace function for a telecine signal.  
OFF ........................ Select this option if there is any jitter or artifacts in video.  
ON ......................... Default standard setting.  
NOTE: This feature is not available for RGB, 480p, 576p and HDTV signals.  
Enabling Key Sound and Error Sound [BEEP]  
This feature turns on or off the button sound or alarm when the following operations are performed.  
- Displaying the main menu  
- Switching sources  
- Resetting data by using [RESET]  
- Pressing POWER ON or POWER OFF button  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Menu  
[OPTIONS(2)]  
Using Off Timer [OFF TIMER]  
1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.  
2. Press the ENTER button on the remote control.  
3. The remaining time starts counting down.  
4. The projector will turn off after the countdown is complete.  
NOTE:  
• To cancel the preset time, set [OFF] for the preset time or turn off the power.  
• When the remaining time reaches 3 minutes before the projector is turned off, the [THE PROJECTOR WILL TURN OFF WITHIN 3  
MINUTES] message will be displayed on the bottom of the screen.  
Selecting Power-saving in [STANDBY MODE]  
The projector has two standby modes: [NORMAL] and [POWER-SAVING].  
The POWER-SAVING mode is the mode that allows you to put the projector in the power-saving condition which  
consumes less power than the NORMAL mode. The projector is preset for NORMAL mode at the factory.  
NORMAL................ Power indicator: Orange light/STATUS indicator: Green light  
POWER-SAVING.... Power indicator: Red light/STATUS indicator: Off  
The following connectors, buttons or functions will not work during this mode.  
- PC CONTROL port, MONITOR OUT connector, and AUDIO OUT connector  
- LAN and Mail Alert functions  
- Buttons other than POWER button on the cabinet  
- Buttons other than POWER ON button on the remote control  
- Virtual Remote function  
NOTE:  
• When [CONTROL PANEL LOCK], [CONTROL ID], or [AUTO POWER ON(COMP1)] is turned on, the [STANDBY MODE] setting is  
not available.  
• Your setting will not be affected even when [RESET] is done from the menu.  
Enabling Auto Power On [AUTO POWER ON(AC)]  
Turns the projector on automatically when the power cable is inserted into an active power outlet. This eliminates the  
need to always use the POWER button on the remote control or projector cabinet.  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1)]  
When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1  
IN input will power on the projector and simultaneously project the computer’s image.  
This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet  
to power on the projector.  
To use this function, first connect a computer to the projector and the projector to an active AC input.  
NOTE:  
• Disconnecting a computer signal from the computer will not power off the projector. We recommend using this function in com-  
bination of the AUTO POWER OFF function.  
• This function will not be available under the following conditions:  
- when a component signal is applied to the COMPUTER1 IN connector  
- when a Sync on Green RGB signal or composite sync signal is applied  
• To enable the AUTO POWER ON (COMP1) after turning off the projector, wait 3 seconds and input a computer signal.  
If a computer signal is still present when the projector is turned off, the AUTO POWER ON (COMP1) will not work and the projector  
remains in standby mode.  
Enabling Power Management [AUTO POWER OFF]  
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5min., 10min.,  
20min., 30min.) if there is no signal received by any input or if no operation is performed.  
Selecting Default Source [DEFAULT SOURCE SELECT]  
You can set the projector to default to any one of its inputs each time the projector is turned on.  
LAST...................................Sets the projector to default to the previous or last active input each time the projector is turned  
on.  
AUTO..................................Searches for an active source in order of COMPUTER1 COMPUTER 2(DIGITAL) COMPUTER2  
(ANALOG) VIDEO S-VIDEO COMPUTER1 and displays the first found source.  
COMPUTER1 ......................Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned  
on.  
COMPUTER2(DIGITAL).......Displays the DVI digital from the COMPUTER 2 IN connector every time the projector is turned on.  
(Not available on NP405/NP305)  
COMPUTER2(ANALOG)......Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned  
on. (“COMPUTER2” on NP405/NP305)  
VIDEO.................................Displays the Video source from the VIDEO IN connector every time the projector is turned on.  
S-VIDEO .............................Displays the Video source from the S-VIDEO IN connector every time the projector is turned on.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
7 Menu Descriptions & Functions [INFO.]  
Displays the status of the current signal and lamp usage.This item has four pages (three pages on NP405 and NP305).  
The information included is as follows:  
TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items.  
[USAGE TIME]  
[LAMP LIFE REMAINING] (%)*  
[LAMP HOURS USED] (H)  
[FILTER HOURS USED] (H)  
[TOTAL CARBON SAVINGS] (kg-CO2)  
*
The progress indicator shows the percentage of remaining bulb life.  
The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the LAMP LIFE  
REMAINING bar indicator changes from 0% to 100 Hours and starts counting down.  
If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the ECO MODE  
is set to OFF or ON.  
The message to the effect that the lamp or the filters should be replaced will be displayed for one minute when  
the projector is turned on and when the POWER button on the projector or the remote control is pressed.  
To dismiss this message, press any button on the projector or the remote control.  
Lamp life(H)  
ECO MODE  
Replacement lamp  
Model  
OFF  
ON  
NP07LP  
NP14LP  
NP610/NP510W/NP410W/NP610S/NP510WS  
NP510/NP410/NP405/NP310/NP305  
4000  
5000  
[TOTAL CARBON SAVINGS]  
This displays the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving cal-  
culation is based on the OECD (2008 Edition).  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. Using On-Screen Menu  
[SOURCE]  
[SOURCE NAME]  
[HORIZONTAL FREQUENCY]  
[SIGNAL TYPE]  
[SOURCE INDEX]  
[VERTICAL FREQUENCY]  
[VIDEO TYPE]  
[SYNC TYPE]  
[SYNC POLARITY]  
[SCAN TYPE]  
[WIRED LAN] (not available on NP405/NP305)  
[PROJECTOR NAME]  
[SUBNET MASK]  
[MAC ADDRESS]  
[IP ADDRESS]  
[GATEWAY]  
[VERSION]  
[PRODUCT]  
[SERIAL NUMBER]  
[FIRMWARE] Version  
[DATA] Version  
[CONTROL ID] (when [CONTROL ID] is set)  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Using On-Screen Menu  
Menu Descriptions & Functions [RESET]  
[NP610/NP510/NP410/NP310/NP510W/NP410W/  
NP610S/NP510WS]  
[NP405/NP305]  
Returning to Factory Default [RESET]  
The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except  
the following:  
[CURRENT SIGNAL]  
Resets the adjustments for the current signal to the factory preset levels.  
The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS],  
[ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].  
[ALL DATA]  
Reset all the adjustments and settings for all the signals to the factory preset.  
All items can be reset EXCEPT [LANGUAGE], [BACKGROUND], [FILTER MESSAGE], [SECURITY], [COMMUNI-  
CATION SPEED], [CONTROL ID], [STANDBY MODE], [FAN MODE], [LAMP LIFE REMAINING], [LAMP HOURS  
USED], [FILTER HOURS USED], [TOTAL CARBON SAVINGS], and [NETWORK SETTINGS].  
To reset the lamp usage time, see “Clearing Lamp Hour Meter [CLEAR LAMP HOURS]” below.  
Clearing Networking Settings [NETWORK SETTINGS] (Not available on NP405/NP305)  
Returns [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY] to the default settings.  
Clearing Lamp Hour Meter [CLEAR LAMP HOURS]  
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press  
the ENTER button.  
NOTE: Elapsed time of the lamp use will not be affected even when [RESET] is done from the menu.  
NOTE: The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the  
lamp has reached the end of its life. In this condition you cannot clear the lamp hour meter on the menu. If this happens, press the  
HELP button on the remote control for 10 seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.  
Clearing the Filter Usage Hours [CLEAR FILTER HOURS]  
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press  
the ENTER button.  
NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6. Maintenance  
This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp.  
1 Cleaning or Replacing the Filters  
The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter  
is dirty or clogged, your projector may overheat.  
NOTE: The message for filter cleaning will be displayed for one minute after the projector is turned on or off.  
To cancel the message, press any button on the projector cabinet or the remote control.  
CAUTION  
Turn off the projector, turn off the main power switch and unplug the projector before replacing the filters.  
Only clean the outside of the filter cover with a vacuum cleaner.  
Do not attempt to operate the projector without the filter cover.  
To clean the air-filter:  
Vacuum the filter-through the filter cover.  
To replace the filter (sponge):  
1. Remove the filter cover (2 locations) by pushing up on the catch of the cover until you feel it detach.  
2. Replace two filters.  
(1) Gently peel off the filter (sponge) and clean the filter cover.  
(2) Attach the new filter to the filter cover.  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6. Maintenance  
3. Reinstall the new filter cover (2 locations).  
Insert the filter cover until you feel click.  
4. Clear the filter hours used.  
To reset the filter usage time, from the menu, select [RESET] [CLEAR FILTER HOURS].  
(page 80 for resetting the filter usage time.)  
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter, remove  
dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.  
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement  
lamp.  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Cleaning the Cabinet and the Lens  
1. Turn off the projector before cleaning.  
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong  
detergents or solvents such as alcohol or thinner.  
Vacuum the ventilation  
inlet of the cabinet.  
Note on Cleaning the Lens (NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W)  
Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.  
Note on Cleaning the Lens (NP610S/NP510WS)  
The NP610S and NP510WS have a plastic lens. Use a commercially available plastic lens cleaner.  
NOTE:  
• Do not scratch or mar the lens surface as a plastic lens is easily scratched.  
• Never use alcohol or glass lens cleaner as doing so will cause damage to the lens surface.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Maintenance  
Replacing the Lamp  
When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red. Even though the lamp may  
still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to  
clear the lamp hour meter. (page 80)  
CAUTION  
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,  
turn off the main power switch and then disconnect the power cable. Allow at least one hour for the lamp to cool  
before handling.  
DO NOT REMOVE ANY SCREWS except one lamp cover screw and two lamp housing screws.You could receive  
an electric shock.  
Do not break the glass on the lamp housing.  
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might cause  
an unwanted shadow and poor picture quality.  
The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours  
after the lamp has reached the end of its life. If this happens, be sure to replace the lamp. If you continue to use  
the lamp after the lamp reaches the end of its life, the lamp bulb may shatter, and pieces of glass may be scattered  
in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC  
dealer for lamp replacement.  
*NOTE: This message will be displayed under the following conditions:  
• for one minute after the projector has been powered on  
• when the  
(POWER) button on the projector cabinet or the POWER OFF button on the remote control is pressed  
To turn off the message, press any button on the projector cabinet or the remote control.  
To replace the lamp:  
Optional lamp and tools needed for replacement:  
Replacement lamp:  
NP07LP (NP610/NP510W/NP410W/NP610S/NP510WS)  
NP14LP (NP510/NP410/NP405/NP310/NP305)  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6. Maintenance  
1. Remove the lamp cover.  
(1)Loosen the lamp cover screw  
• The lamp cover screw is not removable.  
(2)Push and slide the lamp cover off.  
FOCUS  
FOCUS  
M
M
EN  
EN  
U
U
SOURCE  
SOURCE  
AUTOADJ  
AUTOADJ  
LAMP  
LAMP  
.
.
S
S
T
T
A
A
TUS  
TUS  
2. Remove the lamp housing.  
(1)Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condi-  
tion.  
• The two screws are not removable.  
• There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this  
interlock.  
(2)Remove the lamp housing by holding it.  
CAUTION:  
Make sure that the lamp housing is cool  
enough to before removing it.  
FOCU  
FOCU  
S
S
Interlock  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Maintenance  
3. Install a new lamp housing.  
(1)Insert a new lamp housing until the lamp housing is plugged into the socket.  
CAUTION  
Do not use a lamp other than the NEC replacement lamp NP07LP (NP610/NP510W/NP410W/NP610S/NP510WS)/  
NP14LP (NP510/NP410/NP405/NP310/NP305).  
Order this from your NEC dealer.  
(2)Push the top center of the lamp housing to secure it.  
(3)Secure it in place with the two screws.  
• Be sure to tighten the screws.  
FOCU  
OCUS  
S
M
M
E
EN  
NU  
U
SOURC  
SOURCE  
E
AUTOADJ.  
AUTOADJ  
LAMP  
LAMP  
.
S
S
T
T
A
A
TUS  
TUS  
4. Reattach the lamp cover.  
(1)Slide the lamp cover back until it snaps into place.  
(2)Tighten the screw to secure the lamp cover.  
• Be sure to tighten the screw.  
FOCUS  
FOCUS  
M
M
EN  
EN  
U
U
SOURCE  
SOURCE  
AUTOADJ  
AUTOADJ  
LAMP  
LAMP  
.
.
S
S
T
T
A
A
TUS  
TUS  
5. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.  
6. Finally, select the menu [RESET] [CLEAR LAMP HOURS] to reset the lamp usage hours.  
NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector  
cannot turn on and the menu is not displayed.  
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.  
When the lamp time clock is reset to zero, the LAMP indicator goes out.  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
1 Troubleshooting  
This section helps you resolve problems you may encounter while setting up or using the projector.  
Indicator Messages  
Power Indicator  
Indicator Condition  
Projector Condition  
The main power is off  
Note  
Off  
Blinking light  
Green 0.5 sec On,  
0.5 sec Off  
The projector is getting ready to turn on.  
Wait for a moment.  
2.5 sec On,  
0.5 sec Off  
Off Timer is enabled.  
Steady light  
Green  
Orange  
Red  
The projector is turned on.  
[NORMAL] is selected for [STANDBY MODE]  
[POWER-SAVING] is selected for [STANDBY  
MODE]  
Status Indicator  
Indicator Condition  
Projector Condition  
Note  
Normal or Standby ([POWER-SAVING] for  
[STANDBY MODE])  
Off  
Red  
Blinking light  
1 cycle (0.5 sec Lamp cover error or lamp housing error  
On, 2.5 sec Off)  
Replace the lamp cover or lamp housing cor-  
rectly.  
2 cycle (0.5 sec Temperature error  
On, 0.5 sec Off)  
The projector is overheated. Move the projector to  
a cooler location.  
3 cycle (0.5 sec Power error  
On, 0.5 sec Off)  
Power unit is not working properly. Contact your  
dealer.  
4 cycle (0.5 sec Fan error  
On, 0.5 sec Off)  
Fans will not work correctly.  
6 cycle (0.5 sec Lamp error  
On, 0.5 sec Off)  
Lamp fails to light. Wait a full minute and then  
turn on again.  
9 cycle (0.5 sec [DYNAMIC CONTRAST] error  
On, 0.5 sec Off)  
Dynamic Contrast function is not working properly  
on NP410/NP310. Contact your dealer.  
Green  
Re-firing the lamp (The projector is cooling The projector is re-firing.  
down.)  
Wait for a moment.  
Steady light  
Green  
Standby ([NORMAL] for [STANDBY MODE])  
CONTROL PANEL LOCK is on.  
Orange  
You have pressed cabinet button when Control  
Panel Lock is on.  
CONTROL ID error  
Remote control ID and projector ID are not  
matched.  
Lamp Indicator  
Indicator Condition  
Projector Condition  
Note  
Off  
Normal  
Blinking light  
Steady light  
Red  
Lamp has reached its end of life. Lamp replace- Replace the lamp.  
ment message will be displayed.  
Red  
Lamp has been used beyond its limit. The projec- Replace the lamp.  
tor will not turn on until the lamp is replaced.  
Green  
[ECO MODE] is set to [ON]  
Over-Temperature Protection  
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp  
with the STATUS indicator blinking (2-cycle On and Off.)  
Should this happen, do the following:  
• Unplug the power cable after the cooling fans stop.  
• Move the projector to a cooler location if the room where you are presenting is particularly too warm.  
• Clean the ventilation holes if they are clogged with dust.  
• Wait about 60 minutes until the inside of the projector becomes cool enough.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
7. Appendix  
Common Problems & Solutions (“Power/Status/Lamp Indicator” on page 87.)  
Problem  
Check These Items  
Does not turn on  
or shut down  
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote  
control is on. (pages 25, 26, 27)  
Ensure that the lamp cover is installed correctly. (page 86)  
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the  
room where you are presenting is particularly warm, move the projector to a cooler location.  
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of  
its life. If so, replace the lamp. After replacing the lamp, reset the lamp hours used. (page 80)  
The lamp may fail to light. Wait a full minute and then turn on the power again.  
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600  
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting  
to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens,  
wait a couple minutes and turn on the projector. (page 74)  
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an im-  
age for some time and then the projector will display the image. Wait for a moment.  
Will turn off  
No picture  
Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. (page 76, 77)  
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select  
your source (Computer, Video or S-Video). (page 29) If there is still no picture, press the button again.  
Ensure your cables are connected properly.  
Use menus to adjust the brightness and contrast. (page 62)  
Remove the lens cap.  
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (page 80)  
Enter your registered keyword if the Security function is enabled. (page 43)  
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning  
on the power to the notebook PC.  
In most cases the output signal from the notebook PC is not turned on unless connected to the projector  
before being powered up.  
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver  
or power management software.  
See also the next page.  
Picture suddenly  
becomes dark  
Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,  
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. (page 74)  
Color tone or hue is  
unusual  
Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (page 69)  
Adjust [HUE] in [PICTURE]. (page 63)  
Image isn’t square to  
the screen  
Reposition the projector to improve its angle to the screen. (page 30)  
Use the Keystone correction function to correct the trapezoid distortion. (page 34)  
Picture is blurred  
Adjust the focus. (page 33)  
Reposition the projector to improve its angle to the screen. (page 30)  
Ensure that the distance between the projector and screen is within the adjustment range of the lens.  
(page 15, 16)  
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.  
Should this happen, let the projector stand until there is no condensation on the lens.  
Flicker appears on  
screen  
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600  
meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH  
ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. (page 74)  
Image is scrolling  
vertically, horizontally  
or both  
Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is  
supported by the projector. (page 97)  
Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (page 65)  
Remote control does  
not work  
Install new batteries.(page 10)  
Make sure there are no obstacles between you and the projector.  
Stand within 22 feet (7 m) of the projector. (page 10)  
Indicator is lit or blinking  
See the POWER/STATUS/LAMP Indicator. (page 87)  
Cross color in RGB  
mode  
Press the AUTO ADJ. button on the projector cabinet or the remote control. (page 37)  
Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (page 64)  
For more information contact your dealer.  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
If there is no picture, or the picture is not displayed correctly.  
Power on process for the projector and the PC.  
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on  
the power to the notebook PC.  
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before  
being powered up.  
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”,  
this means there is no signal being output from the computer. (page 79 or go to next step)  
Enabling the computer’s external display.  
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.  
When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usu-  
ally, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on  
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through  
external display selections.  
Non-standard signal output from the computer  
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed  
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each  
notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step.  
Refer to your computer’s documentation for detailed information.  
Image displayed is incorrect when using a Macintosh  
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector)  
according to your resolution. After setting, restart your Macintosh for the changes to take affect.  
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch  
on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch  
to the 13" fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable mode  
and then restart the Macintosh again.  
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub  
15-pin connector.  
Mirroring on a PowerBook  
*
When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirroring”  
is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.  
Folders or icons are hidden on the Macintosh screen  
Folders or icons may not be seen on the screen. Should this happen, select [View] [Arrange] from the Apple  
menu and arrange icons.  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
Specifications  
This section provides technical information about projector’s performance.  
Model Number  
Optical  
NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W  
NP610/NP510/NP410/NP405/NP310/NP305  
NP510W/NP410W  
LCD Panel  
NP610/NP510: 0.63 inch LCD with Micro Lens Array 0.59 inch LCD with Micro Lens Array  
(Aspect Ratio 4:3)  
(Aspect Ratio 16:10)  
NP410/NP405/NP310/NP305: 0.63 inch LCD (As-  
pect Ratio 4:3)  
Resolution  
Lens  
1024 × 768 pixels*1  
1280 × 800 pixels*1  
Manual zoom and focus  
Zoom Ratio = 1–1.2  
F1.7–2.0 f = 19.8–23.7 mm  
Lamp  
NP610: 230W AC (170W in ECO Mode)  
NP510/NP410/NP405/NP310/NP305: 180W AC  
(145W ECO Mode)  
230W AC (170W in ECO Mode)  
Light Output*2*3  
NP610: 3500 lumens (approx. 70% in ECO Mode) NP510W: 3000 lumens (approx. 70% in ECO  
NP510: 3000 lumens (approx. 80% in ECO Mode) Mode)  
NP410/NP405: 2600 lumens (approx. 80% in ECO NP410W: 2600 lumens (approx. 70% in ECO  
Mode)  
Mode)  
NP310/NP305: 2200 lumens (approx. 80% in ECO  
Mode)  
Contrast Ratio*3  
NP610/NP510/NP405/NP305: 500:1  
NP510W: 500:1  
(full white: full black)  
NP410/NP310: 2000:1  
NP410W: 450:1  
Image Size (Diagonal) 21–300 inches/ 0.53 m–7.6 m  
Projection Distance  
30–444 inches/0.7–11.3 m  
31–470 inches/0.8–11.9 m  
Projection Angle  
Tele: 7.9°–8.3°/Wide: 9.5°–10.0°  
Tele: 7.9°–8.3°/Wide: 9.5°–10.0°  
*1 Effective pixels are more than 99.99%.  
*2 This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any  
other mode is selected as the [PRESET] mode, the light output value may drop slightly.  
*3 Compliance with ISO21118-2005  
Electrical  
Inputs  
1 RGB/Component (D-Sub 15 P), 1 RGB (Digital/Analog, DVI-I 29P, HDCP*4 supported),  
1 S-Video (DIN 4 P), 1 Video (RCA), 1 (L/R) RCA Audio, 2 Stereo Mini Audio  
DVI-I 29P is not available on NP405/NP305  
Outputs  
1 RGB (D-Sub 15P), 1 Stereo Mini Audio  
1 PC Control Port (D-Sub 9P)  
PC Control  
Wired LAN Port  
External Control  
Color Reproduction  
Compatible Signals*5  
RJ-45 (not available on NP405/NP305)  
RS232, IR, Wired LAN (not available on NP405/NP305)  
16.7 million colors simultaneously, Full color  
Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA  
480i/480p/576i/576p/720p/1080i  
Digital: VGA/SVGA/XGA/WXGA/SXGA  
Video Bandwidth  
RGB: 80 MHz (Max.)  
Horizontal Resolution  
540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60  
300 TV lines: SECAM  
Scan Rate  
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)  
Vertical: 50 Hz to 120 Hz  
Sync Compatibility  
Built-in Speaker  
Separate Sync / Composite Sync / Sync on G  
7W (monaural)  
Power Requirement  
NP610/NP510/NP410/NP405/NP310/NP305: NP510W/NP410W: 100–240V AC, 50/60Hz  
100–240V AC, 50/60Hz  
NP510WG/NP410WG: 200–240V AC, 50/60Hz  
NP610G/NP510G/NP410G/NP405G/NP310G/  
NP305G: 200–240V AC, 50/60Hz  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Appendix  
Input Current  
NP610: 3.8–1.5A  
NP510W/NP410W: 3.8–1.5A  
NP510/NP410/NP405/NP310/NP305: 3.2–1.4A  
NP510WG/NP410WG: 1.8A  
NP610G: 1.8A  
NP510G/NP410G/NP310G/NP405G/NP305G:  
1.5A  
Power Consumption  
NP610: 312W(100-130V AC)/294W(200-240V NP510W/NP410W: 312W(100-130V AC)/294W(200-  
AC) in OFF for ECO MODE/237W(100-130V 240V AC) in OFF for ECO MODE/237W(100-130V  
AC)/228W(200-240V AC) in ON for ECO MODE  
AC)/228W(200-240V AC) in ON for ECO MODE  
NP510/NP410/NP310/NP405/NP305: 251W(100-  
130V AC)/239W(200-240V AC) in OFF for ECO 10W in NORMAL Mode for STANDBY  
MODE/203W(100-130V AC)/195W(200-240V AC) MODE/0.6W(100-130V AC)/0.7W(200-240V AC)  
in ON for ECO MODE  
in POWER-SAVING Mode for STANDBY MODE  
NP610/NP510/NP410/NP310: 10W in NORMAL  
Mode for STANDBY MODE/0.6W(100-130V  
AC)/0.7W(200-240V AC) in POWER-SAVING Mode  
for STANDBY MODE  
NP405/NP305: 8W in NORMAL Mode for STANDBY  
MODE/0.6W(100-130V AC)/0.7W(200-240V AC) in  
POWER-SAVING Mode for STANDBY MODE  
*4 What is HDCP/HDCP technology?  
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content  
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual  
Interface (DVI).  
If you are unable to view material via the DVI input, this does not necessarily mean the projector  
is not functioning properly. With the implementation of HDCP, there may be cases in which certain  
content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP  
community (Digital Content Protection, LLC).  
*5 An image with higher or lower resolution than the projector’s native resolution (NP610/NP510/NP410/  
NP405/NP310/NP305: 1024 × 768 / NP510W/NP410W: 1280 × 800) will be displayed with Advanced  
AccuBlend.  
Mechanical  
Installation  
Dimensions  
Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear  
12.1" (W) × 3.7" (H) × 10.3" (D) /308 mm (W) × 93.5 mm (H) × 262 mm (D)  
(not including protrusions)  
Weight  
NP610/NP510: 6.59 lbs/2.99 kg  
NP410/NP310: 6.61 lbs/3.0 kg  
NP405/NP305: 6.59 lbs/2.97 kg  
NP510W/NP410W: 6.59 lbs/2.99 kg  
Environmental  
Considerations  
Operational Temperatures : 41° to 104°F (5° to 40°C),  
(ECO mode selected automatically at 95°F to 104°F/35°C to 40°C)  
20% to 80% humidity (non-condensing)  
Storage Temperatures : 14° to 122°F (-10° to 50°C),  
20% to 80% humidity (non-condensing)  
Regulations  
UL/C-UL Approved (UL 60950-1, CSA 60950-1)  
Meets DOC Canada Class B requirements  
Meets FCC Class B requirements  
Meets AS/NZS CISPR.22 Class B  
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)  
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
Model Number  
Optical  
NP610S/NP510WS  
NP610S  
NP510WS  
LCD Panel  
0.63 inch LCD with Micro Lens Array  
(Aspect Ratio 4:3)  
0.59 inch LCD with Micro Lens Array  
(Aspect Ratio 16:10)  
Resolution  
Lens  
1024 × 768 pixels*1  
1280 × 800 pixels*1  
Fixed zoom and manual focus  
Digital Zoom Ratio= 1.2  
F2.3 f= 9.7 mm  
Lamp  
Light Output*2*3  
Contrast Ratio*3  
230W AC (170W in ECO Mode)  
2600 lumens (approx. 70% in ECO Mode)  
600:1  
2100 lumens (approx. 70% in ECO Mode)  
57"–104"/1.45 m–2.64 m  
(full white: full black)  
Image Size (Diagonal) 60"–110"/ 1.52 m–2.79 m  
Projection Distance  
35"–66"/ 0.9 m–1.7 m  
Projection Angle  
29.1°–29.4°  
*1 Effective pixels are more than 99.99%.  
*2 This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any  
other mode is selected as the [PRESET] mode, the light output value may drop slightly.  
*3 Compliance with ISO21118-2005  
Electrical  
Inputs  
1 RGB/Component (D-Sub 15 P), 1 RGB (Digital/Analog, DVI-I 29 P, HDCP*4 supported),  
1 S-Video (DIN 4 P), 1 Video (RCA), 1 (L/R) RCA Audio, 2 Stereo Mini Audio  
Outputs  
1 RGB (D-Sub 15P), 1 Stereo Mini Audio  
1 PC Control Port (D-Sub 9P)  
RJ-45  
PC Control  
Wired LAN Port  
External Control  
Color Reproduction  
Compatible Signals*5  
RS232, IR, Wired LAN  
16.7 million colors simultaneously, Full color  
Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA  
480i/480p/576i/576p/720p/1080i  
Digital: VGA/SVGA/XGA/WXGA/SXGA  
Video Bandwidth  
RGB: 80 MHz (Max.)  
Horizontal Resolution  
540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60  
300 TV lines: SECAM  
Scan Rate  
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)  
Vertical: 50 Hz to 120 Hz  
Sync Compatibility  
Built-in Speaker  
Separate Sync / Composite Sync / Sync on G  
7W (monaural)  
Power Requirement  
NP610S: 100–240V AC, 50/60Hz  
NP510WS: 100–240V AC, 50/60Hz  
NP610SG: 200–240V AC, 50/60Hz  
NP510WSG: 200–240V AC, 50/60Hz  
Input Current  
NP610S: 3.8–1.5A  
NP510WS: 3.8–1.5A  
NP610SG: 1.8A  
NP510WSG: 1.8A  
Power Consumption  
312W(100-130V AC)/294W(200-240V AC) in OFF for ECO MODE/237W(100-130V AC)/228W(200-240V  
AC) in ON for ECO MODE/10W in NORMAL Mode for STANDBY Mode/0.6W(100-130V AC)/0.7W(200-  
240V AC) in POWER-SAVING Mode for STANDBY MODE  
*4 What is HDCP/HDCP technology?  
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content  
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual  
Interface (DVI).  
If you are unable to view material via the DVI input, this does not necessarily mean the projector  
is not functioning properly. With the implementation of HDCP, there may be cases in which certain  
content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP  
community (Digital Content Protection, LLC).  
*5 An image with higher or lower resolution than the projector’s native resolution (NP610S: 1024 × 768 /  
NP510WS: 1280 × 800) will be displayed with Advanced AccuBlend.  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
Mechanical  
Installation Orientation Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear  
Dimensions  
12.1"(W) × 5.4"(H) × 11.9"(D)/308 mm(W) × 136 mm(H) × 301 mm(D)  
(not including protrusions)  
Weight  
7.28 lbs/3.3 kg  
Environmental  
Considerations  
Operational Temperatures : 41° to 104°F (5° to 40°C),  
(ECO mode selected automatically at 95°F to 104°F/35°C to 40°C)  
20% to 80% humidity (non-condensing)  
Storage Temperatures : 14° to 122°F (-10° to 50°C),  
20% to 80% humidity (non-condensing)  
Regulations  
UL/C-UL Approved (UL 60950-1, CSA 60950-1)  
Meets DOC Canada Class B requirements  
Meets FCC Class B requirements  
Meets AS/NZS CISPR.22 Class B  
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)  
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)  
For additional information visit:  
For information on our optional accessories, visit our website or see our brochure.  
The specifications are subject to change without notice.  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
Cabinet Dimensions  
NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W  
NP405/NP305  
A U T O A D J . S O U R C E  
U T S A T S  
L A M P  
M E N U  
F O C U S  
Lens center  
308 (12.1")  
78 (3.1")  
76 (3.0")  
Lens center  
Unit: mm (inch)  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
NP610S/NP510WS  
A U T O A D J . S O U R C E  
U T S A S T  
L A M P  
M E N U  
F O C U S  
Lens center  
308 (12.1")  
78 (3.1")  
76 (3")  
Lens center  
Unit: mm (inch)  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
Pin Assignments of D-Sub COMPUTER Input Connector  
Mini D-Sub 15 Pin Connector  
Pin No. RGB Signal (Analog)  
YCbCr Signal  
11 12 13 14 15  
6
7
8
9
10  
1
2
3
Red  
Cr  
Y
Cb  
1
2
3
4
5
Green or Sync on Green  
Blue  
4
5
6
7
Ground  
Ground  
Red Ground  
Green Ground  
Blue Ground  
Signal Level  
Video signal : 0.7Vp-p (Analog)  
Sync signal : TTL level  
Cr Ground  
Y Ground  
Cb Ground  
8
9
No Connection  
Sync Signal Ground  
No Connection  
Bi-directional DATA (SDA)  
Horizontal Sync or Composite Sync  
Vertical Sync  
10  
11  
12  
13  
14  
15  
Data Clock  
NOTE: Pin Nos. 12 and 15 are required for DDC/CI.  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
Compatible Input Signal List  
Horizontal: 15KHz to 100KHz (RGB: 24KHz or over)  
Vertical: 50Hz to 120Hz  
Resolution  
(Dots)  
Frequency H.  
(kHz)  
15.7  
15.6  
15.7  
15.6  
31.5  
31.5  
37.9  
37.5  
39.4  
43.3  
35.2  
37.9  
48.1  
46.9  
53.7  
48.4  
56.5  
60.0  
68.7  
54.4  
64.0  
67.5  
77.5  
47.8  
49.7  
60.0  
75.0  
85.9  
64.0  
80.0  
91.2  
64.7  
65.3  
55.9  
75.0  
81.3  
87.5  
93.8  
35.0  
49.7  
60.2  
68.7  
64.3  
69.9  
78.4  
33.8  
28.1  
45.0  
31.5  
15.7  
15.6  
31.5  
31.3  
Refresh Rate  
(Hz)  
59.9  
50.0  
60.0  
50.0  
59.9  
60.0  
72.8  
75.0  
75.0  
85.0  
56.3  
60.3  
72.2  
75.0  
85.1  
60.0  
70.1  
75.0  
85.0  
60.1  
70.0  
75.0  
85.1  
59.9  
59.8  
60.0  
75.0  
85.0  
60.0  
75.0  
85.0  
60.0  
60.0  
59.9  
60.0  
65.0  
70.0  
75.0  
66.7  
74.6  
74.9  
75.1  
60.4  
65.2  
73.7  
60.0  
50.0  
60.0  
59.9  
59.9  
50.0  
59.9  
50.0  
Signal  
VIDEO  
IBM  
NTSC  
PAL  
PAL60  
SECAM  
-
-
-
-
*
*
*
*
640  
640  
640  
640  
640  
640  
800  
800  
800  
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
480  
480  
480  
480  
480  
480  
600  
600  
600  
600  
600  
768  
768  
768  
768  
864  
864  
864  
864  
768  
800  
960  
960  
960  
800  
800  
1024  
1024  
1024  
1024  
1152  
1152  
1152  
1152  
1280  
1280  
1280  
1280  
1280  
1280  
1280  
1280  
1400  
1400  
1440  
1600  
1600  
1600  
1600  
640  
*
*
*
1024  
1024  
1024  
1050  
1050  
900  
1200  
1200  
1200  
1200  
480  
*
*
*
*
*
*
*
*
Apple Macintosh®  
832  
624  
768  
870  
1024  
1152  
1280  
1280  
1280  
1920  
1920  
1280  
720  
720  
720  
720  
720  
1024  
1024  
1024  
1080  
1080  
720  
*
*
HDTV  
(1080i/60)  
(1080i/50)  
SDTV  
DVD  
480p  
YCbCr  
480  
480  
576  
480  
Progressive  
*
576  
NOTE:  
• Images above flagged with “*” are not supported by digital signal.  
• An image with higher or lower resolution than the projector’s native resolution (NP610/NP510/NP410/NP405/NP310/NP305/  
NP610S: 1024 x 768 / NP510W/NP410W/NP510WS: 1280 x 800) will be displayed with Advanced AccuBlend.  
• Some composite sync signals may not be displayed correctly.  
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh  
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Appendix  
PC Control Codes and Cable Connection  
PC Control Codes  
Function  
Code Data  
POWER ON  
02H  
02H  
02H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
00H  
02H  
02H  
02H  
02H  
02H  
00H  
00H  
00H  
00H  
02H  
03H  
01H  
01H  
01H  
01H  
01H  
12H  
13H  
14H  
15H  
POWER OFF  
01H  
03H  
03H  
03H  
03H  
03H  
10H  
11H  
12H  
13H  
INPUT SELECT COMPUTER 1  
01H  
1AH  
02H  
06H  
0BH  
09H  
22H  
0AH  
0EH  
13H  
INPUT SELECT COMPUTER 2 (Digital) 02H  
INPUT SELECT COMPUTER 2 (Analog) 02H  
INPUT SELECT VIDEO  
INPUT SELECT S-VIDEO  
PICTURE MUTE ON  
PICTURE MUTE OFF  
SOUND MUTE ON  
02H  
02H  
02H  
02H  
02H  
02H  
SOUND MUTE OFF  
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.  
Cable Connection  
Communication Protocol  
Baud rate .........................................19200 bps  
Data length ......................................8 bits  
Parity...............................................No parity  
Stop bit............................................One bit  
X on/off............................................None  
Communications procedure.............Full duplex  
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.  
PC Control Connector (D-SUB 9P)  
To TxD of PC  
To RxD of PC  
To GND of PC  
1
2
3
4
5
6
7
8
9
To RTS of PC  
To CTS of PC  
NOTE 1: Pins 1, 4, 6 and 9 are no used.  
NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.  
NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. Appendix  
7 Troubleshooting Check List  
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by  
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem  
more efficiently.  
* Print this page and the next page for your check.  
Frequency of occurrence always sometimes (How often?_____________________) other (__________________)  
Power  
No power (POWER indicator does not light green) See also “Status  
Indicator (STATUS)”.  
Shut down during operation.  
Power cable’s plug is fully inserted into the wall outlet.  
Lamp cover is installed correctly .  
[AUTO POWER OFF] is turned off (only models with the [AUTO  
POWER OFF] function).  
Power cable’s plug is fully inserted into the wall outlet.  
Main power switch is pressed to the ON position.  
Lamp cover is installed correctly .  
Lamp Hours Used (lamp operation hours) was cleared after  
lamp replacement.  
[OFF TIMER] is turned off (only models with the [OFF TIMER]  
function).  
No power even though you press and hold the POWER button  
for 1 second.  
Video and Audio  
No image is displayed from your PC or video equipment to the  
projector.  
Parts of the image are lost.  
Still unchanged even though you press the AUTO ADJUST  
button.  
Still unchanged even though you carry out [RESET] in the  
projector’s menu.  
Still no image even though you connect the projector to the PC  
first, then start the PC.  
Enabling your notebook PC’s signal output to the projector.  
A combination of function keys will enable/disable the exter-  
nal display. Usually, the combination of the “Fn” key along  
with one of the 12 function keys turns the external display  
on or off.  
Image is shifted in the vertical or horizontal direction.  
Horizontal and vertical positions are correctly adjusted on a  
computer signal.  
Input source’s resolution and frequency are supported by the  
projector.  
No image (blue or black background, no display).  
Still no image even though you press the AUTO ADJUST  
button.  
Still no image even though you carry out [RESET] in the  
projector’s menu.  
Signal cable’s plug is fully inserted into the input connector  
A message appears on the screen.  
( _____________________________________________ )  
The source connected to the projector is active and available.  
Still no image even though you adjust the brightness and/or  
the contrast.  
Some pixels are lost.  
Image is flickering.  
Still unchanged even though you press the AUTO ADJUST  
button.  
Still unchanged even though you carry out [RESET] in the  
projector’s menu.  
Image shows flickering or color drift on a computer signal.  
Still unchanged even though you change [FAN MODE] from  
[HIGH ALTITUDE] to [AUTO].  
Image appears blurry or out of focus.  
Input source’s resolution and frequency are supported by the  
projector.  
Still unchanged even though you checked the signal’s resolution  
on PC and changed it to projector’s native resolution.  
Still unchanged even though you adjusted the focus.  
No sound.  
Image is too dark.  
Remains unchanged even though you adjust the brightness  
and/or the contrast.  
Image is distorted.  
Audio cable is correctly connected to the audio input of the  
projector.  
Still unchanged even though you adjusted the volume level.  
Image appears to be trapezoidal (unchanged even though you  
carry out the [KEYSTONE] adjustment).  
AUDIO OUT is connected to your audio equipment (only models  
with the AUDIO OUT connector).  
Other  
Remote control does not work.  
Buttons on the projector cabinet do not work (only models with the  
[CONTROL PANEL LOCK] function)  
No obstacles between the sensor of the projector and the  
remote control.  
Projector is placed near a fluorescent light that can disturb the  
infrared remote controls.  
[CONTROL PANEL LOCK] is not turned on or is disabled in  
the menu.  
Still unchanged even though you press and hold the EXIT button  
for a minimum of 10 seconds.  
Batteries are new and are not reversed in installation.  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
In the space below please describe your problem in detail.  
Information on application and environment where your projector is used  
Projector  
Installation environment  
Screen size:  
Model number:  
inch  
Serial No.:  
Screen type: White matte Beads Polarization  
Date of purchase:  
Lamp operating time (hours):  
Eco Mode:  
Wide angle High contrast  
Throw distance:  
feet/inch/m  
Off On  
Orientation: Ceiling mount Desktop  
Power outlet connection:  
Information on input signal:  
Horizontal synch frequency  
Vertical synch frequency  
Synch polarity  
[
[
] kHz  
] Hz  
Connected directly to wall outlet  
Connected to power cord extender or other (the  
number of connected equipment______________)  
H (+) (−)  
Connected to a power cord reel or other (the number  
V (+) (−)  
of connected equipment______________)  
Synch type  
Separate Composite  
Sync on Green  
Computer  
STATUS Indicator:  
Steady light  
Manufacturer:  
Orange Green  
Model number:  
Notebook PC / Desktop   
Native resolution:  
Refresh rate:  
Flashing light  
[
] cycles  
Remote control model number:  
Video adapter:  
Other:  
PC  
Projector  
DVD player  
Video equipment  
Signal cable  
VCR, DVD player, Video camera, Video game or other  
NEC standard or other manufacturer’s cable?  
Model number:  
Distribution amplifier  
Model number:  
Switcher  
Length:  
inch/m  
Manufacturer:  
Model number:  
Model number:  
Adapter  
Model number:  
100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
6) Problems or damage caused by expendable supplies or devices  
connected to the product other than those designated by NEC.  
TravelCare Guide  
TravelCare - a service for international travelers  
7) Problems caused by natural consumption, wear or deterioration  
of parts under normal usage conditions.  
This product is eligible for “TravelCare”, NEC’s unique international  
warranty.  
Please note that TravelCare coverage differs in part from coverage under  
the warranty included with the product.  
8) Problems or damage to lamps and other expendable supplies,  
included parts or optional parts.  
9) Other conditions stipulated in the warranty included with the  
product also apply.  
Services offered with TravelCare  
This warranty allows customers to receive service on their product at the  
NEC and NEC-designated service stations in the countries listed herein  
when temporarily traveling internationally for business or pleasure.  
For details on services offered by the different service stations, please  
refer to the “List of TravelCare Outlets” below.  
NOTE: The product can be used overseas with voltages indicated in the rating  
label on the product by using a power cable suited for the standards and power  
source voltage of the country in which the product is being used.  
List of TravelCare Outlets  
This list applies as of July 1, 2009.  
1 Repair services  
For the most up-to-date information, please refer to the websites of the  
service stations in the various countries on the List of TravelCare Outlets  
The product will be repaired and delivered within 10 business days,  
not including shipping time.  
During the term of warranty, the cost of maintenance parts, labor costs  
for repairs and shipping costs within the service station’s coverage  
area are covered by the warranty.  
In Europe  
NEC Europe Ltd. / European Technical Centre  
Address:  
Telephone:  
Fax Line:  
Email Address: [email protected]  
WEB Address:  
Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.  
+44 1952 237000  
+44 1952 237006  
2 Replacement product rental service  
If the customer desires, he or she can rent a replacement product  
while the original product is being repaired.  
Fee: US$200 for 12 days  
This fee must be paid at the local service station in cash or credit  
card.  
The US$200 rental fee is non-refundable even if the customer rents  
it less than 12 days before returning.  
The replacement product will be delivered within 3 business days.  
If the customer did not return the replacement product within 12 days,  
the customer will be charged the price of the unit.  
If the customer returned the replacement product in a faulty or dam-  
aged condition, the repair cost will be charged to the customer.  
Note that this service is not offered in all countries and regions.Please  
refer to the “List of TravelCare Outlets”.  
(Regions Covered)  
EU:  
Austria*, Belgium*, Bulgaria*, Czech Republic*, Cyprus*,  
Denmark*, Estonia*, Finland*, France*, Germany*, Greece*,  
Hungary*, Ireland*, Italy*, Latvia*, Lithuania*, Luxembourg*,  
Malta*, The Netherlands*, Poland*, Portugal*, Romania*,  
Slovakia*, Slovenia*, Spain*, Sweden* and the United  
Kingdom*  
EEA: Norway*, Iceland and Liechtenstein  
In North America  
NEC Display Solutions of America, Inc.  
In addition, this replacement product rental service is not offered after  
the product’s warranty has expired.  
Address:  
500 Park Boulevard, Suite 1100 Itasca, Illinois  
60143, U.S.A.  
+1 800 836 0655  
+1 800 356 2415  
Term of warranty  
1
Telephone:  
Fax Line:  
Email Address: vsd.tech-support@necdisplay.com  
a. Upon presentation of the warranty or receipt received upon  
purchase:  
WEB Address:  
Valid for the term indicated on the warranty or the normal term  
of warranty for the country of purchase.  
(Regions Covered)  
U.S.A. *, Canada*  
b. When only the product is brought in:  
In Oceania  
AWA Limited.  
Valid for a period of within 14 months of the date of manufacture  
indicated by the serial number attached to the product.  
Address:  
151 Arthur Street  
Homebush West NSW 2140 Australia  
2
3
When a product whose term of warranty is expired is brought in:  
Repairs will be offered for a fee.In this case the customer is not eligible  
for the replacement product rental service.  
Customer Call Centre  
Telephone:  
Fax Line:  
0297647777  
1300772688  
In the following cases, repairs may be charged, even if the product’s  
warranty is still in effect:  
Email Address: [email protected]  
1) If the term of warranty, model name, serial number and name of  
the store of purchase are not indicated on the warranty or have  
been altered.  
For Travel Care service, while customer is in Australia, the customer  
will contact AWA on 1300366144, select Option 4. If you want to  
book warranty service by email customer goes to:  
2) Problems or damage caused by dropping or shocks during ship-  
ment or movement by the customer or by improper handling by  
the customers.  
(Regions Covered)  
Australia  
3) Problems or damage caused by improper usage or unwarrantable  
alterations or repairs by the customer.  
Visual Group Ltd.  
Address:  
4) Problems or damage caused by fire, salt damage, gas damage,  
earthquakes, lightning damage, storm or flood damage or other  
natural disasters or such external factors as dust, cigarette  
smoke, abnormal voltage, etc.  
28 Walls Road Penrose Auckland New Zealand  
095250740  
095809607  
Telephone:  
Fax Line:  
Email Address: [email protected]  
5) Problems or damage caused by use in hot or humid places, in  
vehicles, boats or ships, etc.  
(Regions Covered)  
New Zealand  
101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
7. Appendix  
In Asia and Middle East  
NEC Display Solutions, Ltd.  
Hyosung ITX Co., Ltd.  
Address:  
1st Fl., Ire B/D. #2, 4Ga, Yangpyeng-Dong,  
Youngdeungpo-Gu, Seoul, Korea 150-967  
+82 2 2163 4193  
Address:  
686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,  
Kanagawa 258-0017, Japan  
+81 465 85 2369  
Telephone:  
Fax Line:  
Telephone:  
Fax Line:  
+82 2 2163 4196  
+81 465 85 2393  
Email Address: [email protected]  
Email Address: [email protected]  
WEB Address:  
(Regions Covered)  
South Korea  
(Regions Covered)  
Japan*  
Lenso Communication Co., Ltd.  
Address:  
292 Lenso House 4, 1st Floor, Srinakarin Road,  
NEC Solutions (China) Co.,Ltd.  
Huamark, Bangkapi, Bangkok 10240, Thailand  
+66 2 375 2425  
+66 2 375 2434  
Address:  
Rm 1903, Shining Building, 35 Xueyuan Rd,  
Telephone:  
Fax Line:  
Haidian District Beijing 100083, P.R.C.  
+8610 82317788  
+8610 82331722  
Telephone:  
Fax Line:  
Email Address: [email protected]  
WEB Address:  
Email Address: [email protected]  
(Regions Covered)  
Thailand  
WEB Address:  
(Regions Covered)  
China  
ABBA Electronics L.L.C.  
Address:  
Tariq Bin Ziyad Road, P.O.Box 327, Dubai, United  
Arab Emirates  
+971 4 371800  
+971 4 364283  
NEC Hong Kong Ltd.  
Address:  
Telephone:  
Fax Line:  
25/F., The MetropolisTower, 10 Metropolis Drive,  
Hunghom, Kowloon, Hong Kong  
+852 2369 0335  
Email Address: [email protected]  
Telephone:  
Fax Line:  
+852 2795 6618  
(Regions Covered)  
Email Address: [email protected]  
United Arab Emirates  
WEB Address:  
Samir Photographic Supplies  
Address:  
Telephone:  
Fax Line:  
P.O.Box 599, Jeddah 21421, Saudi Arabia  
+966 2 6828219  
+966 2 6830820  
(Regions Covered)  
Hong Kong  
Email Address: [email protected]  
NEC Taiwan Ltd.  
Address:  
7F, No.167, SEC.2, Nan King East Road, Taipei,  
Taiwan, R.O.C.  
+886 2 8500 1700  
Riyadh  
Address:  
Telephone:  
Fax Line:  
P.O.Box 5519, Riyadh 11432, Saudi Arabia  
+966 1 4645064  
+966 1 4657912  
Telephone:  
Fax Line:  
+886 2 8500 1420  
Email Address: [email protected]  
Email Address: [email protected]  
WEB Address:  
Alkhobar  
(Regions Covered)  
Taiwan  
Address:  
Telephone:  
Fax Line:  
P.O.Box 238, Alkhobar 31952, Saudi Arabia  
+966 3 8942674  
+966 3 8948162  
NEC Asia Pte.Ltd.  
Email Address: [email protected]  
Address:  
401 Commonwealth Drive, #07-02, Haw Par  
Technocentre, Singapore 149598  
+65 6 273 8333  
(Regions Covered)  
Saudi Arabia  
Telephone:  
Fax Line:  
+65 6 274 2226  
Email Address: [email protected]  
NOTE: In countries designated with an asterisk(*), replacement product rental  
WEB Address:  
service are offered.  
(Regions Covered)  
Singapore  
NEC Corporation of Malaysia Sdn. Bhd.  
Address:  
33rd Floor, Menara TA One, 22, Jalan P. Ramlee,  
50250 Kuala Lumpur, Malaysia  
+6 03 2178 3600 (ISDN)  
+6 03 2178 3789  
Telephone:  
Fax Line:  
Email Address: [email protected]  
WEB Address:  
(Regions Covered)  
Malaysia  
102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
P-1/  
,
Date:  
/
/
,
TO: NEC or NEC’s Authorized Service Station:  
FM:  
(Company & Name with signature)  
Dear Sir (s),  
I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your  
following conditions, and also the Service fee will be charged to my credit card account, if I don’t return the Loan units within the  
specified period. I also confirm following information is correct. Regards.  
Application Sheet for TravelCare Service Program  
Country,  
product purchased :  
User’s Company Name :  
User’s Company Address :  
Phone No., Fax No. :  
User’s Name :  
User’s Address :  
Phone No., Fax No. :  
Local Contact office :  
Local Contact office Address :  
Phone No., Fax No. :  
User’s Model Name :  
Date of Purchase :  
Serial No. on cabinet :  
Problem of units per User :  
Required Service :  
(1) Repair and Return  
(1) Credit Card  
(2) Loan unit  
Requested period of Loan unit :  
Payment method :  
(2) Travelers Cheque  
(3) Cash  
In Case of Credit Card :  
Card No. w/Valid Date :  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
5. Loan Service Charges and Conditions:  
Upon acceptance of this NEC Projector, Customer agrees to assume  
liability for this loan unit.  
Condition of your TravelCare Service Program  
Enduser is requested to understand following condition of TravelCare  
Service Program and complete the necessary information on the ap-  
plication sheet.  
The current cost of use of this loan unit is US$200 for 12 calendar  
days.  
1. Service Options:  
There are 3 types of [Service] available. Enduser has to understand  
following condition and is required to fill in the Application Sheet.  
If Customer does not return the unit within the 12 calendar days, Cus-  
tomer will be charged the next highest cost up to and including the full  
list price to Credit Cards, which price will be informed by NEC Authorized  
Service Stations. Please see the attached listing of contacts for each  
country to arrange for pickup of the loan unit.  
1) Repair and Return:  
The ‘Faulty unit’ is sent or collected from the customer. It is repaired  
and returned within 10 days to the customer, excluding transport  
time.  
If you return to their country of origin with the loan unit, you will be charged  
additional freight to return the unit to the loaning country.  
There may have a case, repair and return can’t be done by NEC  
Authorized Service Station, because of shortage of spare parts due  
to same model is not sold in the territory.  
Thank you for your understanding of this program.  
2) Repair and Return with Loan: (This service is limited to some Service  
Stations)  
This service is offered to the Enduser, who cannot wait until their unit  
is repaired.  
The customer can borrow a unit for US$200 up to 12 days. Customer  
then sends in inoperable unit to nearest NEC Authorized Service  
Station for service. In order to prevent collection problem, Enduser  
is required to fill in Application Sheet.  
Enduser needs to confirm the availability of the Service to NEC  
Authorized Service Stations.  
3) Loan Only:  
For this service, NEC Authorized Service Station supplies the cus-  
tomer with a loan unit for US$200 up to 12 days. Customer keeps the  
inoperable unit and when customer returns home, customer arranges  
to have the projector serviced in the home country.  
2. Warranty Exclusions:  
This program does not apply if the Projector’s serial number has been  
defaced, modified or removed.  
If, in the judgement of NEC Authorized Service Station or its agent the  
defects or failures result from any cause other than fair wear and tear or  
NEC neglect, or fault including the following without limitation:  
1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke  
or default of or by the Customer its employees or agents or any third  
party;  
2) Failure or fluctuation of electrical power, electrical circuitry, air con-  
ditioning, humidity control or other environmental conditions such as  
use it in smoking area;  
3) Any fault in the attachments or associated products or components  
(whether or not supplied by NEC or its agents which do not form part  
of the Product covered by this warranty);  
4) Any act of God, fire, flood, war, act of violence or any similar occur-  
rence;  
5) Any attempt by any person other than any person authorized by NEC  
to adjust, modify, repair, install or service the product.  
6) Any Cross-border charges such as, duty, insurance, tax etc.  
3. Charges for Warranty Exclusions and Out of Warranty Case:  
In case faulty unit is under warranty exclusions case or under Out of  
Warranty period, NEC Authorized Service Station will Inform estimation  
of actual service cost to the Enduser with reason.  
4. Dead on Arrival (DOA):  
Enduser must take this issue up with their original supplier in the country  
of purchase.  
NEC Authorized Service Station will repair the DOA unit as a Warranty  
repair, but will not exchange DOA unit with new units.  
104  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© NEC Display Solutions, Ltd. 2009  
7N951361  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Clothes Dryer 10 000 750 User Manual
Miller Electric Welder WC 115A User Manual
Milwaukee Drill 54 46 0101 User Manual
Minolta Computer Drive PCL6 User Manual
MTD Lawn Mower 80M User Manual
National Instruments Network Card NI TB 2706 User Manual
Nikon Camera Accessories MB D10 User Manual
Onkyo Stereo Receiver TX 8222 User Manual
Panasonic Automobile Parts MBYT User Manual
Panasonic Smoke Alarm 3309 User Manual