Operating instructions
Heat pump dryer
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-GB
M.-Nr. 10 000 750
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Caring for the environment .................................................................................. 2
Warning and Safety instructions ......................................................................... 6
Operating the tumble dryer................................................................................. 18
Before using for the first time............................................................................. 20
1. Notes on correct laundry care........................................................................ 21
Garment care label symbols............................................................................. 22
2. Load the tumble dryer ..................................................................................... 23
3. Select a programme and start it..................................................................... 24
4. Remove the laundry......................................................................................... 27
Remove the laundry............................................................................................... 27
Options.................................................................................................................. 28
Delay start............................................................................................................. 29
Programme chart................................................................................................. 30
Changing the programme sequence ................................................................. 33
Cleaning and care................................................................................................ 34
Emptying the condensed water container............................................................. 34
Removing the plinth filter.................................................................................. 37
Cleaning the plinth filter.................................................................................... 37
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Checking the condenser unit............................................................................ 38
Fragrance flacon .................................................................................................. 41
Problem solving guide......................................................................................... 45
Other problems...................................................................................................... 48
After sales service ............................................................................................... 51
Repairs................................................................................................................... 51
Installation and connection................................................................................. 52
Consumption data ............................................................................................... 61
Technical data ..................................................................................................... 62
Programmable functions..................................................................................... 64
Cottons programme - drier or damper............................................................. 67
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Extended cool down....................................................................................... 67
Buzzer volume ................................................................................................ 67
Keypad tone.................................................................................................... 67
Code................................................................................................................ 68
Conductivity.................................................................................................... 68
Additional drying levels................................................................................... 69
Standby............................................................................................................. 70
Automatic switch-off........................................................................................ 71
Memory ............................................................................................................ 71
Anti-crease....................................................................................................... 71
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
It is essential to read these instructions.
This tumble dryer complies with current safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the tumble dryer,
please read these instructions carefully before using it for the first
time. They contain important information on its safety, installation,
use and maintenance.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
This tumble dryer is intended for use in domestic households and
similar working and residential environments.
This tumble dryer is not intended for outdoor use.
It must be used only as a domestic appliance to dry items which
have been washed in a water solution and which are marked on the
manufacturer's care label as being suitable for tumble drying. If
using dry cleaning kits, do so at your own risk, and follow the
instructions provided on the packaging.
Any other applications may be dangerous. Miele cannot be held
liable for damage resulting from incorrect or improper use or
operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This tumble dryer can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience or
knowledge, if they are supervised whilst using it or have been shown
how to use it in a safe way and understand and recognise the
consequences of incorrect operation.
Safety with children
Children under 8 years of age must be kept away from the tumble
dryer unless they are constantly supervised.
Children 8 years and older may only use the tumble dryer
unsupervised if they have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
Children must not be allowed to clean or maintain the tumble
dryer unsupervised.
Please supervise children in the vicinity of the tumble dryer and
do not let them play with it.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Before setting up the tumble dryer, check it for any externally
visible damage.
Do not install or use a damaged tumble dryer.
Before connecting the tumble dryer, ensure that the connection
data on the data plate (fuse rating, voltage and frequency) match the
mains electricity supply. If in any doubt, consult a qualified
electrician.
Reliable and safe operation of this tumble dryer can only be
assured if it has been connected to the mains electricity supply.
The electrical safety of this tumble dryer can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt, please have the household
wiring system tested by a qualified electrician. Miele cannot be held
liable for the consequences of an inadequate earthing system (e.g.
electric shock).
Do not connect the appliance to the mains electricity supply by an
extension lead, multi-socket adapter or similar. These can overheat
and are a fire hazard.
If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
Unauthorised repairs could result in unforeseen dangers for the
user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician, otherwise any
subsequent damage will not be covered by the guarantee.
Faulty components must only be replaced by genuine Miele
original spare parts. The manufacturer can only guarantee the safety
of the appliance when Miele replacement parts are used.
The tumble dryer must be isolated from the electricity supply in
the event of a fault and during cleaning and maintenance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This tumble dryer must not be used in a non-stationary location
(e.g. on a ship).
Do not make any alterations to the tumble dryer, unless
authorised to do so by Miele.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Heat pump technology and refrigerant:
The heat pump in this tumble dryer uses a refrigerant which is
condensed by the compressor and led in a closed circuit through
the heat exchanger unit where heat exchange with the circulating
drying air takes place.
– The humming noises caused by the heat pump are normal and do
not impair the efficient functioning of the dryer.
– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any
length of time before it is connected to the mains provided it has
been transported and installed correctly (see "Installation and
connection").
If it has not been transported as described, ensure that the
recommended standing time prior to first operation is observed.
Otherwise the heat pump can be damaged.
– This tumble dryer contains fluorinated greenhouse gases. They
are hermetically sealed.
Designation: R 134a
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Please observe the instructions in "Installation and connection"
and the "Technical data".
The accessibility of the plug must always be ensured, in order to
disconnect the tumble dryer from the mains.
Do not block the gap between the bottom of the tumble dryer and
the floor with plinth facings, deep pile carpet etc. This would hinder
a sufficient flow of air to the dryer.
Make sure the dryer door can be opened without hindrance after
installation.
Correct use
The maximum load for this tumble dryer is 8.0 kg (dry weight).
The maximum recommended loads for individual programmes are
given in the Programme chart.
To prevent the risk of fire, do not connect the tumble dryer via a
controllable socket (e.g. a timer or a peak-load switch-off device).
If the drying programme is interrupted before the end of the cooling
down phase, this could cause the laundry to self-ignite.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
To prevent the risk of fire, the following textiles must not be dried
in this tumble dryer:
– Items which have not been washed.
– Items, such as workwear, which have not been thoroughly
cleaned and which are still soiled with grease, oil or other
deposits (such as cosmetics, lotions etc). If items have not been
thoroughly cleaned there is a danger that these might ignite when
heated, even after they have been removed from the dryer at the
end of the programme.
– Items (e.g. mops and floor cloths) which have been treated with
inflammable cleaning agents or which contain residues of
acetone, alcohol, benzene, petrol, kerosene, stain remover,
turpentine, wax and wax remover or other chemicals.
– Items which have been splashed with hair lacquer, hair spray, nail
varnish remover or similar substances.
When washing such heavily soiled items ensure that you use
sufficient detergent and select a high temperature. If in doubt,
wash the items several times.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Remove all items from pockets (e.g. lighters, matches).
Warning: Do not switch the dryer off before the drying
programme has finished. If this is done, the laundry must be hung
up or spread out to cool it down.
Fabric conditioner and similar products must be used according
to the instructions on the manufacturer's packaging.
To prevent the risk of fire, the following textiles must not be dried
in this tumble dryer:
– Items which have been cleaned using chemicals (e.g.
professional dry-cleaning agents).
– Items which contain a large proportion of rubber, foam rubber or
rubber-like materials. For example, products made from latex
foam rubber, shower caps, waterproof textiles, rubberised articles
and items of clothing and pillows with foam rubber filling.
– Damaged items which contain padding or fillings (e.g. pillows,
jackets). When damaged, the filling can get out with the risk of it
igniting in the dryer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In many programmes, the heating phase is followed by a cooling
down phase to ensure that the items are not too hot to handle when
you remove them (this also avoids the danger of the laundry self-
igniting). The programme is not finished until the cooling down
phase has been completed.
As soon as the programme has finished, remove all laundry from the
drum.
Do not let anyone sit or lean on the door, as this can cause the
tumble dryer to tip up.
Always close the door after use. This way you will avoid the
danger of:
– Children climbing onto or into the dryer or hiding things in it.
– Pets or other small animals climbing into it.
The tumble dryer must not be used without fluff filters or
– with damaged fluff filters, or
– with a damaged plinth filter.
This would cause an excessive build-up of fluff which in turn would
cause a fault.
The fluff filters must be cleaned after every drying cycle.
The fluff filters and the plinth filter must be thoroughly dried after
cleaning. Do not replace them if they are damp or wet. Damp or wet
filters could cause operational faults.
Do not install the tumble dryer in a room where there is a risk of
frost occurring. At temperatures around freezing point the tumble
dryer may not be able to operate properly. There is a risk of damage
if the condensed water is allowed to freeze in the pump and hoses.
If the water is drained externally through the drain hose instead of
being collected in the condensed water container, make sure the
drain hose is securely attached if you hang it in a sink or basin to
avoid the hose slipping and the water causing damage.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Condensed water is not drinking water.
It can cause health problems in both people and animals if
consumed.
Always keep the area around the tumble dryer free of dust and
fluff.
Dust drawn into the tumble dryer can cause blockages in the heat
exchanger over time.
The tumble dryer must not be hosed down.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Using a fragrance flacon (optional accessory)
Only use genuine Miele original fragrance flacons.
The fragrance flacon must be stored in its packaging so please
make sure you retain this.
Caution. The fragrance can leak out of the flacon. Make sure that
you always keep the flacon, or the fluff filter with the flacon inserted
in it, in a horizontal position when carrying and do not tip or place
down on any surface.
Use an absorbent cloth to wipe up any fragrance which has
leaked out of the flacon onto the floor, the dryer or any dryer
components (e.g. the fluff filter) immediately.
If fragrance which has leaked out of a flacon: comes into contact
with the skin - wash the skin thoroughly with soap and water;
comes in contact with the eyes - rinse the eyes with clean water for
at least 15 minutes; is swallowed - rinse out the mouth thoroughly
with clean water. Seek medical advice in the case of contact with
the eyes or if fragrance has been swallowed.
If fragrance which has leaked out of a flacon comes in contact
with clothing, change the clothing immediately. Wash the clothing or
any cloths used for mopping up fragrance thoroughly with plenty of
water and detergent.
There is the risk of fire or damage to the tumble dryer if the
following instructions are not observed:
– Never refill a flacon with fragrance.
– Never use a faulty fragrance flacon.
Dispose of an empty fragrance flacon with the household waste
and never use it for any other purpose.
Please also observe the information supplied with the fragrance
flacon.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Accessories
Only use genuine Miele original spare parts and accessories with
this appliance. If non-Miele parts are used, guarantee, performance
and product liability claims will be invalidated.
The tumble dryer can be combined with a Miele washing machine
in a washer-dryer stack. The appropriate "WTV" stacking kit
(available to order) to match your tumble dryer and washing machine
is required.
If you order a plinth for this tumble dryer (available from Miele as
an optional accessory - depending on country), make sure it is the
correct one.
Miele cannot be held liable for damage caused by non-
compliance with these Warning and Safety instructions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the tumble dryer
Control panel
a
d
e
f
Programme selector
For selecting the programme.
Display with and sensors
See the following page for more
information.
Optical interface
For service technicians.
b
c
Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
button
The tumble dryer is switched on and
off by pressing this button. To save
energy, the dryer will switch off
automatically 15 minutes after the
end of the programme/anti-crease
phase or after being switched on if
no other selection is made.
Option buttons
Various options can be added to the
programmes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the tumble dryer
i
Drying level display
Display
For selecting the drying level for
programmes with a selectable
drying level. See " sensor".
j
sensor
This sensor has two functions.
Touching the symbol will . . .
. . . select a later start time for the
programme (delay start). will
flash during selection, will light
up constantly when the delay start
time is counting down.
. . . select the duration of the Warm
air programme. will flash during
selection.
g
Time display
The programme duration remaining
will be displayed in hours : minutes.
The duration displayed for the
Cottons, Minimum iron, Delicates,
Express, Denim, Gentle smoothing
programmes may vary or "jump".
The following factors, among others,
affect the programme duration
displayed: the quantity of laundry,
the type of fabric and the residual
moisture in the laundry. The
k
Perfect Dry indicator
With programmes with a selectable
drying level, the Perfect Dry system
calculates the residual moisture
present in the laundry to ensure a
precise drying result.
The Perfect Dry indicator . . .
. . . will flash after the programme
has started and go out when the
programme duration appears in the
display.
. . . will light up again when the
selected drying level is reached and
remain on until the end of the
programme.
. . . will remain dark with the
following programmes: Woollens
handcare, Silks handcare, Warm air.
electronics continually assess
conditions in the appliance and then
adjust the programme duration with
increasing accuracy.
h
Check/fault indicators
These are only visible when
necessary.
...
l
sensor
... empty the condensed water
container or check the drain hose
...
... clean the plinth filter/airways
...
Touching this symbol will select the
drying level required which will then
light up .
... technical fault, call the Service
Department
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Removing the protective foil
and stickers
Remove
– the protective foil from the door.
– any stickers from the front and the
lid.
Please do not remove any labels
(e.g. the data plate), visible when you
open the door.
After installing the dryer
Before using the tumble dryer for
the first time, ensure that it is
installed and connected to the
electricity supply correctly. If it has
not been transported as described in
"Installation and connection" then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply.
Follow the procedure for using
for the first time outlined in
these instructions.
Read "1. Notes on correct laundry
care" and "2. Load the tumble dryer".
You can then load the dryer and
select a programme as described in
"3. Select a programme and start it".
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Notes on correct laundry care
Points to note regarding
washed laundry
– When washing very heavily soiled
items ensure that you use sufficient
detergent and select a high
See "Warning and Safety"
instructions for further information.
Loading or using the tumble dryer
incorrectly could cause a fire.
– Sort the laundry according to the
type of fibre and weave, size,
garment care label symbol and the
drying level required.
temperature. If in doubt, wash the
items several times.
– Do not put soaking wet items into the
tumble dryer. Make sure your laundry
is thoroughly spun before drying. The
higher the spin speed, the greater the
savings that can be made in energy
and time during drying.
– Check the seams of padded or
down-filled items to prevent the risk
of fillings coming out. These could
catch fire when being dried.
– Disentangle the laundry.
– New dark coloured garments should
be washed and dried separately from
light coloured garments to avoid the
danger of colours running and
discolouring other garments or even
plastic components in the dryer. Dark
coloured fibres can also settle on
light coloured garments and vice
versa.
– Tie together textile belts and ties.
– Fasten . . .
. . . duvet covers and pillow cases to
prevent small items from being
trapped inside them.
. . . hooks and eyes.
– Sew in or remove underwiring from
bras.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– Leave jackets open and undo any
long zips so that textiles dry evenly.
– Minimum iron fabrics tend to crease
more, the greater the load. This is
also the case for garments made
from very fine weave fabric, such as
shirts or blouses. If necessary,
reduce the size of the load for these
types of fabric.
Preparing the laundry before
drying
Make sure that any objects, e.g.
detergent dosing balls, lighters etc.
have been removed from the
laundry.
They could melt or explode and
cause damage to the dryer or the
laundry.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Notes on correct laundry care
Garment care label symbols
Drying
– Down-filled garments have linings
which have a tendency to shrink,
depending on the quality of the item.
They can be partially dried using the
Gentle smoothing programme.
Normal/higher temperature
Reduced temperature:
Select Gentle tumble (for delicate
textiles)
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may
Do not tumble dry
otherwise become rough. They can
be partially dried using the Gentle
smoothing programme.
Ironing
Very hot
Hot
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be "fluffed up" in the Woollens
handcare programme.
Warm
Do not iron
Laundry care when drying in a
tumble dryer
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry these
textiles. When purchasing these
garments it is advisable to take their
shrinkage properties into account.
See the "Programme chart".
This describes the programmes and
gives their maximum load.
– Select the Gentle tumble option for
fabric which is particularly heat-
sensitive or susceptible to creasing.
– Load according to the optimum
amount of laundry recommended for
the programme being used.
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
– Select an appropriate drying level,
e.g. . . .
. . . Normal if you want to fold and put
away the laundry after you take it out
of the dryer.
. . . Machine iron if the laundry, e.g.
table linen, requires further
processing after drying.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Load the tumble dryer
When closing the door make sure
that laundry does not get trapped in
the door opening.
It is essential to read "1. Notes
on correct laundry care" first of
all.
This could damage the laundry.
Press the button to switch the
dryer on.
The interior drum lighting will come on.
The interior drum lighting will
automatically go out after a few
minutes and/or after the start of a
programme to save energy.
Open the door
If you are not using a fragrance
flacon: the tab must be pushed
down completely (see arrow).
Close the door
Reach under the door grip and pull
the door open.
Unfold the laundry and load loosely
into the drum.
Do not overload the drum.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
Shut the door with a gentle swing.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Any drying level can be selected for the
Select a programme
Cottons and Express programmes. A
more limited range is available when
using the other programmes.
Additional drying levels
Tip: Using the programmable functions
you can activate/deactivate additional
drying levels.
if 2 drying levels then the following
are lit up
additional drying level is
selected
Extra dry
Normal
Normal+
= drier than Normal
Turn the programme selector.
Normal
Slightly dry
Hand iron
= damper than Normal
A drying level or option buttons may
also light up and durations will appear
in the time display.
Hand iron
Machine iron
Hand iron
= damper than Hand iron
– Please see "Programmable functions
Programmes with drying levels
- Additional drying levels".
– Cottons, Minimum iron, Delicates,
Express, Denim, Gentle smoothing
The drying level can be altered after
selecting one of these programmes.
Touch the sensor to select the
drying level required.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Other programmes and the timed
drying programmes
– Cottons , Woollens handcare,
Silks handcare
The drying level is preset and cannot
be altered.
– Warm air
You can select the duration in ten-
minute stages.
Touch the sensor repeatedly until
the programme duration you want
appears in the time display.
– will flash
You can select the duration in ten-
minute stages from minutes up to
hours.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a programme and start it
Delay start
Select any options or delay
start (if required)
You can delay the start of the
programme.
However: delay start cannot be used
with the Warm air programme.
Please see "Options" for further
information.
To select options
Touch the sensor.
– will flash
Press a button.
The button will light up when the option
is selected.
Please see "Delay start" for more
information.
Start the programme
Press the flashing Start/Stop button.
The Start/Stop button will now light up
constantly.
The Perfect Dry indicator will only flash/
light up with programmes with
selectable drying levels (see also
"Operating the tumble dryer").
The laundry will be cooled down shortly
before the end of the programme.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the laundry
End of programme/Anti-crease
Check that all items have been
removed from the drum.
If items are left in the dryer, they
could be damaged by overdrying
when the dryer is next used.
At the end of the programme: will
light up in the display and the Start/
Stop button will go out. The anti-crease
function, if selected, will then switch on
for a maximum of 2 hours.
If the dryer is switched on at the mains
and the door is opened, the drum
lighting will come on. It will go out a few
minutes later to save energy.
10 minutes after the end of the
programme the Start/Stop button will
begin to flash slowly and the display
will go out: this is Standby mode to
save energy.
If the dryer is still switched on, switch
it off with the button.
The dryer will switch off automatically
15 minutes after the end of the anti-
crease phase (with programmes without
an anti-crease phase it will switch off
15 minutes after the end of the
programme).
A buzzer will sound.
Remove the fluff from the 2 fluff filters
in the door opening: see "Cleaning
and care - Fluff filters".
Shut the door with a gentle swing.
Remove the laundry
Empty the condensed water
container.
Never open the door before the
drying process has finished.
Reach under the door grip and pull
the door open.
Remove the laundry.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Buzzer
A buzzer (four beeps at intervals for a
maximum of 1 hour) will sound to let
you know that the programme has
finished. The continuous buzzer which
sounds when there is a fault is not
dependent on the setting for the buzzer
at the end of the programme.
Selectable options
Gentle tumble
Anti-crease
The options are switched on or off by
pressing the appropriate button.
Buzz
er
The button will light up when the option
is selected.
–
X
X
–
X
X
X
–
X
X
X
X
Cottons
Cottons
Gentle tumble
Delicate fabric (with the symbol on
the care label, e.g. acrylic garments) is
dried at a lower temperature. The
programme duration is longer.
Minimum iron
Woollens
handcare
Silks
handcare
–
X
X
Anti-crease
Depending on the programme selected,
the drum will continue to rotate in a
special rhythm for up to 2 hours at the
end of the programme, to reduce
creasing, if you do not wish to remove
the laundry immediately.
Delicates
Express
Denim
O
–
X
X
X
X
X
X
X
X
X
O
Gentle
smoothing
Warm air
X
X
X
X = Can be selected
O = Cannot be changed/always active
– = Cannot be selected
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Delay start
– The drum will turn briefly every hour
until the start of the programme to
reduce creasing.
To select delay start
With delay start you can delay the start
of the programme by up to a maximum
of 24 hours.
To change delay start after it
has started counting down
Press the Start/Stop button.
However: delay start cannot be used
with the Warm air programme.
– will flash
Touch the sensor to change the
time.
Press the Start/Stop button.
To add/remove laundry after
delay start has started
counting down
You can open the door to add/
remove laundry.
– All programme settings will be saved
After selecting the programme touch
the sensor.
– will flash
– will flash
You can also change the drying level, if
required.
– Times of up to are selected in
minute stages and then in hour
stages up to .
Press the Start/Stop button so that
the delay start time continues to
count down.
– If you touch the sensor continuously,
the time will count up to .
To cancel delay start
Switch the dryer off and then on
again.
– Touching the sensor again when
shows in the display will delete
the time selected.
To begin delay start
Press the Start/Stop button.
– will light up
– Delay start times of more than will
count down in hours and then in
minutes until the start of the
programme.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Max. load 8.0 kg*
Cottons **
Use for
Cotton items such as those described under Cottons Normal with
normal residual moisture.
Note
– Items are dried to a Normal level only.
– The Cottons programme is the most energy-efficient for
drying cotton items with normal residual moisture levels.
Cottons
Max. load 8.0 kg*
Extra dry, Normal
Use for
Note
Single and multi-layered cotton fabric such as towelling, jerseywear,
T-shirts, underwear, workwear, covers, flannelette bed linen and
baby clothes.
– Select Extra dry for multi-layered and very thick fabric.
– Do not use Extra dry for jersey fabric (e.g. T-shirts, underwear), as
they have a tendency to shrink.
Hand iron, Machine iron
Use for
Cotton or linen fabric requiring further processing, e.g.: table linen,
bed linen, starched laundry.
Note
To prevent laundry from drying out it should be rolled up until you
are ready for ironing.
Minimum iron
Max. load 4.0 kg*
Normal, Hand iron
Use for
Minimum iron items made of cotton, synthetic or mixed fibre, e.g.:
workwear, tunics, tops, dresses, trousers, table linen and socks.
* Weight of dry laundry
** Note for test institutes:
Test programme in accordance with Regulation 392/2012/EU for energy labelling,
measured in accordance with EN 61121 (without any options selected)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Woollens handcare
Max. load 2.0 kg*
Use for
Woollen garments and fabric containing wool blends, e.g. pullovers,
jackets and socks.
Note
– Wool and wool blend items are only fluffed up; they are not dried
completely.
– Remove garments as soon as the programme has finished.
Silks handcare
Max. load 1.0 kg*
Use for
Silk garments which are suitable for drying in the tumble dryer, e.g.
blouses and shirts
Note
– This programme reduces creasing. Items are not dried completely
by this programme.
– Remove garments as soon as the programme has finished.
Delicates
Max. load 2.5 kg*
Normal, Hand iron
Use for
Delicate items with the symbol on the care label made of
synthetic fibre, mixed fibre, rayon and easy care cotton, e.g. shirts,
blouses, lingerie and appliqued garments.
Note
Reducing the load will reduce creasing.
Express
Max. load 4.0 kg*
Extra dry, Normal, Hand iron, Machine iron
Use for
Note
Garments suitable for the Cottons programme.
The programme duration is shorter.
Denim
Max. load 3.0 kg*
Normal, Hand iron
Use for
Denim garments, e.g. jeans, jackets, skirts, shirts
* Weight of dry laundry
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Gentle smoothing
Normal, Hand iron
Max. load 1.0 kg*
Use for
– Cotton and linen fabric
– Minimum iron items made of cotton, synthetic or mixed fibre, e.g.
trousers, jackets, shirts.
Note
– Suitable for dry and damp laundry.
– Select Hand iron if the items are to be ironed after drying.
– Smooths out creasing caused during the spin cycle in the washing
machine.
– Remove garments as soon as the programme has finished.
Warm air
Max. load 8.0 kg*
Use for
– Multi-layered fabric whose layers have different drying
characteristics, e.g. jackets, pillows, sleeping bags and other
voluminous items.
– Drying individual items, e.g. bath towels, swimwear and tea-
towels.
Note
Tip
Do not select the longest drying time to start with. Check the items
as you are drying them to find the optimum time.
You can use the Warm air programme to help remove odours from
clean cotton clothing (select a duration between 1/2 and 1 hour). To
improve the freshening up effect, dampen the garments a little
beforehand and use a fragrance flacon (optional accessory). Odours
will not be removed as effectively from any parts of the garments
which are made of synthetic fibre.
* Weight of dry laundry
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the programme sequence
You cannot change to another
Adding or removing laundry
after a programme has started
Press the Start/Stop button.
programme once a programme has
started (this prevents unintentional
alterations).
The items will be cooled down,
depending on the temperature reached
and how long they have been dried for.
will light up if you press the Start/
Stop button again during this cooling
down phase.
If you move the programme selector,
will light up until you move the
programme selector back to the original
programme.
You will need to cancel the current
programme before you can select a
new one.
Danger of burning.
Do not touch the back of the drum
when adding or removing items. The
drum and the items can be very hot.
Cancelling a programme while
it is running and selecting a
new programme
Add or remove items.
Close the door.
Press the Start/Stop button.
The items will be cooled down,
depending on the temperature reached
and how long they have been dried for.
will light up if you press the Start/
Stop button again during this cooling
down phase.
To continue with the programme:
(select a drying level first of all, if
necessary)
Press the Start/Stop button.
Press the button to switch the
dryer off.
Programme duration
Altering the programme sequence can
cause the programme duration shown
in the time display to be adjusted.
Press the button to switch the
dryer on.
Select and start a new programme
straight away.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Emptying the condensed water
container
The condensed water is collected in
the condensed water container.
Empty the condensed water
container after every drying
programme.
The indicator will light up if the
maximum level of the condensed water
container is reached.
To delete the indicator: open and
close the door with the dryer switched
on.
Empty the container.
Replace the container in the dryer.
Condensed water should not be
consumed. It could lead to health
problems for people and animals.
To prevent damaging the door
and the front of the condensed water
container when pulling the container
out of the dryer:
Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.
always close the door completely.
Pull out the condensed water
container.
To prevent water running out, hold it
at the front and towards the back and
keep it in a horizontal position when
carrying it.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Fluff filters
This tumble dryer has 2 fluff filters in
the door opening: the upper and lower
fluff filters trap fluff produced during
the drying process.
Removing visible fluff
Remove any fluff after every drying
cycle.
Tip: You can also use a vacuum cleaner
so that you can remove the fluff without
touching it.
Remove the fluff (see arrows) . . .
Open the door.
You must remove the fragrance
flacon (if present) beforehand. See
"Fragrance flacon".
. . . from the surfaces of all the fluff
filters.
. . . from the perforated laundry
deflector.
Push the upper fluff filter back into
position until it clicks.
Pull the upper fluff filter forwards to
remove it.
Close the door.
If there is a great deal of compacted
fluff carry out the following
procedure.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the fluff filters and air flow
openings thoroughly
Hold the dial and pull the fluff filter
forwards to remove it.
If the drying duration has become
longer or the surface of the filters is
visibly compacted with fluff, you
should carry out the following
cleaning procedure.
If using a fragrance flacon make
sure you remove it beforehand.
Pull the upper fluff filter forwards to
remove it.
Use a vacuum cleaner with a long
crevice nozzle attached to remove
any visible fluff from the upper air
flow openings.
Cleaning the fluff filters with water
Flush the fluff filters through with hot
running water.
Shake the fluff filters thoroughly and
then dry them carefully.
Ensure the filters are dry before
replacing them. Wet filters could
cause operational faults.
Turn the yellow dial on the lower fluff
filter in the direction of the arrow (until
you hear it click).
Push the lower fluff filter in
completely and lock it with the yellow
dial.
Push the upper fluff filter in
completely.
Close the door.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Removing the plinth filter will cause the
right hand guide pin in the dryer to
come out. This pin ensures that the
heat exchanger access panel can only
be closed if the plinth filter is inserted
the right way round.
Plinth filter
Only clean the plinth filter when the
indicator lights up.
To delete the indicator: open and
close the door with the dryer switched
on.
Cleaning the plinth filter
Removing the plinth filter
Pull the handle out of the plinth filter.
Clean the filter thoroughly under
running water.
Press the round, indented area on the
heat exchanger access panel to open
it.
Squeeze the plinth filter thoroughly.
The plinth filter must not be
replaced dripping wet as this can
cause a fault.
The panel will spring open.
Use a damp cloth to remove any fluff
from the handle.
Pull the plinth filter out by the handle.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the plinth filter panel
Checking the condenser unit
Danger of injury. Do not touch
the cooling fins. You could cut
yourself.
Look to see if fluff has accumulated.
If there is visible soiling:
Clean using a vacuum cleaner
with a dusting brush attached.
Carefully pass the vacuum cleaner
brush over the heat exchanger
cooling fins without applying any
pressure. Otherwise the cooling fins
could be bent out of shape or
become damaged.
Use a damp cloth to remove any fluff.
Make sure that you do not damage
the rubber seal when doing this.
Check whether the cooling fins are
blocked with fluff (as follows).
Carefully vacuum up any visible fluff
or soiling.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Replacing the plinth filter
Close the heat exchanger access
panel.
The dryer can only be operated
with the plinth filter fitted correctly
and the heat exchanger access
panel closed. The access panel must
be closed correctly to ensure that
water cannot leak from the
condenser system and to ensure that
the dryer functions efficiently.
Fit the filter back on the handle. Make
sure it is the correct way round.
To ensure that the filter is positioned
correctly in the front of the heat
exchanger unit:
First insert the handle with the plinth
filter attached over the two guide
pins.
– The word Miele on the handle must
be the correct way up.
Push the plinth filter in completely.
The act of pushing in the plinth filter will
also push in the right hand guide pin.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Tumble dryer
Disconnect the tumble dryer
from the mains electricity supply.
Do not use solvents, abrasive
cleaners, glass cleaners or all-
purpose cleaners.
These could damage plastic
surfaces and other parts.
Clean the tumble dryer with a slightly
damp cloth and a mild non-abrasive
cleaning agent or a solution of
washing-up liquid and water.
Clean the seal around the inside of
the door with a damp cloth.
Dry all parts with a soft cloth.
The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner
following the manufacturer's
instructions.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
Using a fragrance flacon (optional
accessory) will add a pleasant
fragrance to your laundry.
Before using a fragrance flacon,
please read "Warning and safety
instructions - Using a fragrance
flacon (optional accessory)".
Inserting a fragrance flacon
Only hold the fragrance flacon as
illustrated. Do not hold it at an angle
or tip it as the fragrance will leak out
of the flacon.
Open the cover using the tab until the
tab is at the top right hand side as
shown.
Insert the flacon in the opening as far
as it will go.
Hold the flacon securely to prevent
opening it by mistake.
Pull off the protective seal.
Open the door of the tumble dryer.
The fragrance flacon is inserted in the
upper fluff filter in the opening on the
right hand side beside the grip.
If you are not using a fragrance
flacon: the cover must always remain
closed (push the cover down
completely with the tab).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
– You will feel a slight resistance and
hear a soft click.
Markers and must line up with
one another.
Marker must be in position : this
is the position at which you can feel
a resistance.
Before drying
You can select the intensity of the
fragrance.
Turn the outer ring clockwise a
little.
Turn the outer ring clockwise: the
further you open the flacon, the more
intense the fragrance.
Damp laundry and longer drying
durations with sufficient heat transfer
are needed for the fragrance to be
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
released into the laundry effectively.
The fragrance will also be noticeable in
the room air during the process.
Replacing the fragrance flacon
When the fragrance is no longer
sufficiently intense:
After drying
To avoid the fragrance escaping
needlessly:
Turn the outer ring anti-clockwise
until markers a and b line up.
Turn the outer ring anti-clockwise
until marker b is in position _.
– You will feel a slight resistance.
If you want to dry laundry without
adding fragrance occasionally: remove
the fragrance flacon and store it in its
original packaging until you want to
use it again. See the following section.
Replace the fragrance flacon with a
new one.
Fragrance flacons are available to
order from Miele or online at
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Fragrance flacon
– when purchasing new fragrance
flacons: only remove the protective
seal just before use
Cleaning the fluff filters
The intensity of the fragrance will be
diminished if the fluff filters and the
plinth filter are not cleaned.
The fragrance filter must be
removed before cleaning the fluff
filter.
Never lay the fragrance flacon
down on any surface as the
fragrance will leak.
To prevent any fragrance leaking
out of the flacon:
when not in use, the fragrance flacon
must only be stored in its original
packaging as illustrated.
Only store the fragrance flacon in its
original packaging
Clean the fluff filters and the plinth
filter: see "Cleaning and care".
– when storing the fragrance flacon in
its original packaging whilst you are
not using it, e.g. whilst cleaning the
tumble dryer: to prevent the
fragrance leaking do not store the
packaging upright on its edge or
upside down.
– store in a cool, dry place
– store away from direct sunlight
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
Repair work to electrical appliances must only be carried out by a suitably
qualified person in strict accordance with current local and national safety
regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
Check indicators and fault messages
Problem
Cause and remedy
The programme is
This is not a fault.
cancelled, lights up In some programmes, if the drum has been
underloaded or is empty, the programme will be
cancelled. This can also happen if the items are
already dry.
Open and close the door to resume drying.
Dry individual items using the Warm air timed
drying programme.
flashes/lights up
after the tumble dryer
has been switched on
and a programme
Access via a code has been activated.
See "Programmable functions - Code".
cannot be selected
and (e.g. )
light up after a
programme has been
cancelled
No obvious cause.
Switch the dryer off and then on again.
Start a programme.
If the programme is cancelled again and an error
message appears, there is a fault. Contact the Miele
Service Department.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Cause and remedy
There is a build-up of fluff in the airways.
Clean the fluff filters.
lights up at the end
of a programme
Clean the plinth filter.
See "Cleaning and care".
To switch off:
Open and close the door while the dryer is
switched on.
An excessive amount of fluff has built up.
Clean the fluff filters.
Clean the plinth filter.
and light up after
a programme has been
cancelled
Clean the airways:
– Clean the area underneath the plinth filter.
– Clean the heat exchanger.
To switch off:
Switch the dryer off and back on again.
lights up after a
programme has been
cancelled
The condensed water container is full or there is kink
in the drain hose.
Empty the container.
Check the drain hose.
To switch off:
Open and close the door while the dryer is
switched on.
lights up
The programme selector has been moved.
Select the original programme. The time remaining
will appear in the display again.
Bars flash in the display The programme has finished but the laundry has not
at the end of a
programme:
.........
yet cooled down.
Either remove the laundry and spread it out to cool
down or leave it in the tumble dryer to cool down
during the cooling phase.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Unsatisfactory drying results
Problem
Cause and remedy
The load consisted of different types of fabric.
Finish drying using the Warm air timed drying
programme.
The laundry is not
sufficiently dry
Select a different programme next time.
Tip: You can alter the drying levels for some
programmes (see "Programmable functions").
Laundry or feather filled The laundry was washed with insufficient detergent
pillows smell after
drying
Feathers are a natural product and this is quite
normal.
Laundry: use sufficient detergent next time.
Pillows: take out of the tumble dryer and air them.
Use a fragrance flacon (available as an optional
accessory) for your favourite fragrance.
Items made of synthetic Synthetic fibres tend to attract static charge.
fibres are charged with
static electricity after
drying
Static charge can be reduced by adding a fabric
conditioner to the final rinse in the washing
programme.
There is a build-up of
fluff
Fluff is principally the result of friction when garments
are being worn and to some extent when they are
being washed. Machine drying hardly causes any fluff
to form.
Fluff is collected by the fluff filters and the plinth filter
and can be removed easily.
See "Cleaning and care".
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Other problems
Problem
Cause and remedy
The drying process
goes on too long or
even switches off *
The room in which the dryer is located is too warm.
Ventilate the room thoroughly.
Detergent residues, hair and fine fluff can clog the
filters.
Clean the fluff filters and the plinth filter.
Remove any visible fluff:
. . . bottom left, from behind the panel in the heat
exchanger cavity (see "Cleaning and care");
. . . from the cooling fins behind the grille bottom
right (see the end of this section).
The cool air intake (bottom right grille) is blocked.
Move any objects, such as a laundry basket, away
from the dryer.
The fluff filters and the plinth filter were wet when
replaced.
The fluff filters and the plinth filter must be dry.
The laundry is too damp.
Spin using a higher spin speed in the washing
machine.
The tumble dryer has been overloaded
Do not exceed the maximum load for the
programme selected.
Metal zips have prevented the dryer from registering
the correct moisture level.
Open the zips next time.
If the problem recurs, dry these items using the
Warm air timed drying programme.
* Before starting another programme:
Switch the dryer off and then on again.
There are humming
noises
The compressor is operating.
These noises are quite normal and do not indicate a
fault.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Cause and remedy
A programme does not
start
No obvious cause.
Connect the tumble dryer to the mains
Turn on the tumble dryer
Close the door
Check whether the mains fuse has tripped
Has there been a power cut? When power is restored
any previously running programme will restart
automatically.
The display is dark and The dryer is in standby mode. This is quite normal
the Start/Stop button is and does not indicate a fault.
flashing slowly
See "Programmable functions - Standby".
The drum will turn at intervals in the anti-crease
phase.
The dryer is switched
off at the end of the
programme
The dryer switched off automatically. This is quite
normal and does not indicate a fault.
See "Programmable functions - Automatic
switch-off".
The interior drum
lighting does not come
on
The drum lighting will switch off automatically ...
... when the door is closed.
... after a few minutes when the door is open (to save
energy).
If the dryer is switched on, the drum lighting will
come on when the door is opened.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Bottom right grille
Danger of injury. Do not touch
the cooling fins. You could cut
yourself.
In general, the cooling fins
behind the grille on the bottom right
do not need cleaning. They should
only be cleaned if the drying process
is taking an exceptionally long time
due to a very high level of dust or
fluff in the room in which the dryer is
located.
Use a vacuum cleaner with a
dusting brush attached to clean the
cooling fins. Only pass the vacuum
cleaner brush over them lightly,
without applying any pressure.
Take care not to bend the cooling
fins out of shape or to damage them.
First open the plinth filter panel
(bottom left).
Carefully vacuum up any visible fluff
Then insert a spoon handle behind
or soiling.
the grille on the right hand side.
Re-insert the 3 hooks on the grille
into the appropriate holes in the front
of the dryer.
Lever off the grille at the top (1.).
Lever off the grille at the bottom (2.).
Open the grille out to the right (3.) ...
Press the grille firmly back into
position by pressing it in at the top
and bottom on the left.
... and pull it forwards releasing its 3
hooks to remove it from the dryer.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
Repairs
Optional accessories
In the event of any faults which you
Optional accessories for this tumble
cannot remedy yourself, please contact dryer are available from Miele, your
your Miele Dealer or the Miele Service
Department.
Miele dealer or via the internet at:
Contact details for Miele are given at
the end of this booklet. N.B. A call-out
fee will be charged for service visits
where the problem could have been
resolved as described in these
instructions.
Dryer basket
The dryer basket is suspended in the
drum and does not rotate with the
drum. This enables items which must
not be subjected to mechanical action
to be dried or aired.
When contacting the Service
Department, please quote the model
and serial numbers both of which are
given on the data plate (visible when
the door is open).
Fragrance flacon
A fragrance flacon can be used in your
tumble dryer to add a pleasant
fragrance to your laundry.
Guarantee: U.K.
In the U.K. the appliance is guaranteed
for 2 years from the date of purchase.
However, you must activate your cover
by calling 0330 160 6640 or registering
Guarantee: Other countries
For information on the appliance
guarantee specific to your country
please contact Miele. See end of this
booklet for contact details.
Please note that telephone calls may
be monitored or recorded for training
purposes.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Front view
a
e
Mains connection cable
Heat exchanger access panel
– do not open during drying
b
Control panel
f
g
Four height adjustable screw feet
c
Condensed water container
– empty after every drying cycle
Cool air intake grille
– do not obstruct with a laundry
basket or other objects
d
Door
– do not open during drying
h
Hose for external drainage of
condensed water
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Rear view
If transporting the dryer at an
angle, only tip towards the left side.
a
Protruding lid for holding when
moving the dryer (see arrows)
b
Accessories for external drainage of
condensed water: hose clip, adapter
and hose holder
c
Hose for external drainage of
condensed water
d
Mains connection cable
Transporting the dryer
To manoeuvre the dryer out of its
packing case to its installation site, hold
it by
– the front feet
If the tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply.
Otherwise the heat pump can be
damaged.
– and the lid where it protrudes at the
back of the appliance.
Only transport the dryer as
shown in the following illustrations.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Ventilation
Installation
Levelling the dryer
The cool air intake at the front of
the dryer must not be blocked or
covered. This would hinder a
sufficient intake of cool air for the
heat exchanger.
Make sure the dryer door can be
opened without hindrance after
installation.
Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep
pile carpet etc. This would hinder a
sufficient flow of air to the dryer.
Air which is taken in to cool the heat
exchanger is then blown back out of
the dryer and warms up the air in the
room. It is therefore very important to
ensure adequate ventilation, e.g. by
opening a window. Otherwise drying
durations may be longer (increased
energy requirement).
The appliance must stand perfectly
level to ensure safe and proper
operation.
Before moving the tumble dryer
again (e.g. when moving house)
After each use a small quantity of
condensed water will collect in the area
of the pump. This water can run out if
the tumble dryer is tipped up when it is
being moved. Recommendation: run
the Warm air programme for
approximately 1 minute before moving
the tumble dryer. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.
The screw feet can be adjusted to
compensate for unevenness in the
floor.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
– Building-under kit
Additional installation
requirements
A building under kit is required if
the lid of the tumble dryer needs to
be removed in order to build it under
a worktop.
It must be installed/dismantled by a
suitably qualified fitter.
For safety reasons the tumble
dryer must be disconnected from the
electricity supply before installation.
Building under a continuous
worktop/in a row of kitchen units
The lid of the tumble dryer is replaced
by the cover plate supplied with the
building under kit. It must be fitted by a
suitably qualified fitter to ensure
electrical safety.
It is very important to avoid a
build-up of heat. The warm air which
is expelled from the dryer must be
able to dissipate. Warm air which
cannot dissipate could cause a fault.
Fitting instructions are supplied with the
building-under kit.
– The electrical socket must be located
in an accessible position near the
appliance.
Optional accessories
– Washer-dryer stack
– Drying durations may increase
slightly.
The tumble dryer can be combined with
a Miele washing machine in a washer-
dryer stack. The appropriate Miele
washer-dryer stacking kit is required.
A build-up of heat can be avoided by:
– Adjusting the screw feet so that there
is a gap of at least 20 mm between
the floor and the bottom of the dryer.
– Plinth
The tumble dryer can be fitted on a
plinth with drawer (please note the
plinth may not be available in all
countries).
– Creating a gap for the dryer in the
kitchen furniture plinth facing.
– Creating ventilation gaps in the
kitchen unit.
Pushing the dryer under a worktop
This tumble dryer is suitable for
pushing under a worktop if there is
space to do this without removing the
lid.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Installation conditions requiring a
non-return valve
External condensed water
outlet
There is a risk of back-flow into
the dryer if a non-return valve is not
fitted.
Back-flow could damage the dryer
and also the room in which it is
located.
Certain installation conditions, such
as those described below, require
the fitting of a non-return valve.
Notes
When drying is in progress,
condensed water is pumped into the
condensed water container through
the drain hose which is located at the
back of the dryer.
The condensed water can also be
drained away via the drain hose so that
the condensed water container does
not have to be emptied.
Maximum delivery head with non-return
valve fitted: 1.00 m
Drain hose length: 1.60 m
Maximum delivery head: 1.50 m
Maximum drain hose length: 4.00 m
Installation conditions requiring the
fitting of a non-return valve:
– Drainage into a sink or floor gully
where the end of the hose is
immersed in water.
The following optional accessories
are available:
– Connection to a sink drain outlet.
– an extension hose,
– Connection to a drainage system
already in use by another appliance,
e.g. a dishwasher or washing
machine.
– a non-return valve kit for connection
to an external water outlet. The kit
includes an extension hose.
The non-return valve has to be
fitted with the arrow pointing in the
direction of flow.
Otherwise water will not drain out of
the appliance.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Arranging the drain hose
Do not pull on the drain hose
and do not stretch it or allow it to
become kinked.
This could damage the hose.
There will be a small amount of residual
water left in the drain hose. Have a
container ready to collect this.
Guide the hose to the right or left
side of the dryer, as required.
– If you are guiding it to the right you
can fit the hose into the groove.
– Leave the hose in the lower holder to
prevent it from being kinked by
mistake.
Pull the drain hose off its connection.
Unwind the hose and pull it carefully
out of the holders.
Allow any residual water to run into
the container.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Examples
Direct connection to a sink drain
outlet
– Drainage into a sink or floor gully
Use the hose holder to prevent the
drain hose from becoming kinked.
Remove the following from the back
of the dryer at the top: Adapter 1 and
hose clip 3 behind it.
Press the small catches on the left
and right of the hose holder with your
thumbs (black arrows) and ...
Connect the drain hose as described
below.
... pull the hose holder forwards to
remove it (white arrows).*
If you want to drain the water off
into a sink or basin, you will need to
secure the hose carefully, e.g. by
tying it to a tap, to make sure it
cannot slip during use (see the
drawing under "Installation and
connection - Front view").
Overflowing water can cause
damage.
The non-return valve can be fitted in
the end of the hose.
* You can refit the hose holder at a
later stage if you decide that you no
longer want to drain the condensed
water externally.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Fit adapter 1 to the sink drain outlet
using nut 2.
The nut is usually fitted with a washer
which must be removed.
Attach the end of the hose 4 to
adapter 1.
Use the hose holder.
Use a screwdriver to tighten hose clip
3 up close to the nut.
Fit non-return valve 5 to tumble dryer
drain hose 6.
Non-return valve 5 has to be fitted so
that the arrow points in the direction
of flow (i.e. towards the sink).
1. Adapter
2. Nut
Secure the non-return valve using
hose clips.
3. Hose clip
4. End of the hose (secured with the
hose holder)
5. Non-return valve
6. Tumble dryer drain hose
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out The fuse cover must be refitted when
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
changing the fuse, and if the fuse cover
is lost, the plug must not be used until
a suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Please ensure the connection data
quoted on the data plate match the
household mains supply.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption data
Final spin speed in
a domestic
Residual
moisture
Energy
Duration
1
Load
washing machine
kg
rpm
%
kWh
min
8.0
4.0
1000
1000
60
60
2.14
1.28
156
94
2
Cottons
Cottons Normal
8.0
8.0
8.0
1200
1400
1600
53
50
44
1.90
1.80
1.60
141
134
119
Cottons Normal
+ Gentle tumble
8.0
1000
60
2.19
163
Cottons Hand iron
8.0
8.0
8.0
8.0
1000
1200
1400
1600
60
53
50
44
1.52
1.35
1.25
1.05
115
101
94
80
Minimum iron Normal
+ Gentle tumble
4.0
4.0
1200
1200
40
40
0.69
0.80
55
60
Minimum iron Hand iron
Denim Normal
4.0
3.0
4.0
1200
900
40
60
60
0.60
1.42
1.20
48
106
88
Express Normal
1000
1
Weight of dry laundry
2
Test programme in accordance with Regulation 392/2012/EU for energy labelling, measured in
accordance with EN 61121
All data was calculated using EN 61121 unless otherwise stated.
Power consumption when switched off
Power consumption when not switched off
0.15 W
1.50 W
Note for test institutes:
For testing in accordance with EN 61121, before testing, dry a 3 kg load of cotton laundry with 70%
residual moisture as per the above standard using the Cottons Normal programme without any options
selected.
Consumption data can vary from the nominal values given above depending on the size of the
load, type of fabric, residual moisture level after spinning, fluctuations in the electricity supply
and any options selected.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
850 mm
Width
596 mm
Depth
636 mm
Depth with door open
Height for building under
Width for building under
Depth for building under
Suitable for pushing under a worktop
Suitable for stacking
Weight
1054 mm
820 mm (+8/-2 mm)
600 mm
600 mm
Yes
Yes
Approx. 61 kg
120 litres
Drum volume
Load size
8.0 kg (weight of dry laundry)
Capacity of condensed water container 4.8 litres
Hose length
1.60 m
Maximum delivery head
Maximum drain hose length
Length of connection cable
Voltage
1.50 m
4.00 m
2.00 m
See data plate
See data plate
See data plate
See data plate
See "Consumption data"
Class 1
Connected load
Fuse rating
Test certificates awarded
Energy consumption
LEDs
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Various settings can be reprogrammed to alter the dryer's electronics to suit
different requirements. They can be altered at any time.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Programming
II) To select a programmable
function
You can use the programmable
functions to alter the dryer's
electronics to suit your requirements.
The number of the programmable
function will appear in the display as
and a number:
Please read the following pages
which describe the various
programmable functions so that you
are aware of the effect selecting the
different options will have on your
dryer.
e.g. .
Touch the sensor to select the
other programmable functions one
by one:
Programmable function
Programming is carried out in 8 steps
(, , ... ) using buttons and
sensors.
Cottons programme - drier or
damper
Minimum iron programme -
I) To access a programmable
function
Before you begin, ensure that:
– The tumble dryer is switched off.
– The door is closed.
drier or damper
Extended cool down
Buzzer volume
Keypad tone
Code
Press the Start/Stop button and
keep it pressed in whilst carrying out
steps -.
Conductivity
Additional drying levels
Standby
Switch the dryer on.
Wait until the Start/Stop button lights
up constantly ...
Automatic switch-off
Memory
... and then release the Start/Stop
Anti-crease
button.
Confirm your selection of the
programmable function by pressing
the Start/Stop button.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Confirm your selection of the option
selected by pressing the Start/Stop
button.
III) To select a different option
The options allow you to alter the
features of the particular programmable
function.
The number of the programmable
function: e.g. will light up again.
The option will appear in the time
display as and a number: e.g. or
or etc.
IV) To exit programming
Switch the dryer off.
Touch the sensor to switch to the
The option you have selected is now
stored in memory. You can change it
again at any time.
next option:
Programmable function
The following example illustrates the
programming procedure.
Available options
X
X
X
O
X
X
O
X
O
X
X
X
X
X
X
X
X
X
X
O
O
X
X
X
X
X
X
X
O
to
O
O
X
O
X
X
O
X
O
O
X = Can be selected
O = Factory default setting
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
III) To select a different option
Example
will light up in the time display.
These numbers mean that the keypad
tone is switched off.
The example describes how to call up
the " Keypad tone" programmable
function. When the Keypad tone
programmable function is switched
on, a tone will sound every time a
button is pressed when operating the
dryer.
To switch on the keypad tone:
Touch the sensor so that
lights up.
Confirm selection of by pressing
the Start/Stop button.
I) To access programming
Before you begin, ensure that:
will light up again.
– The tumble dryer is switched off.
– The door is closed.
IV) To exit programming
Switch the dryer off.
Press the Start/Stop button and
keep it pressed in whilst carrying out
steps -.
To check the programming
Switch the dryer on.
Press any button.
Switch the dryer on.
A tone will sound each time you press a
button.
Wait until the Start/Stop button lights
up constantly . . .
Switch the dryer off.
. . . and then release the Start/Stop
button.
Reverting to the previous
programming
will light up
You can switch off the keypad tone at
any time by repeating the steps
described in this example.
II) Selecting the programmable
function
Touch the sensor repeatedly until
Select the option in step .
lights up.
Confirm selection of by pressing
the Start/Stop button.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Cottons programme - drier Extended cool down
or damper
or
The automatic cooling down phase
which takes place before the end of a
programme can be extended for all
programmes with selectable drying
levels. This makes the garments
easier to handle.
Minimum iron programme
- drier or damper
The electronics are designed to dry as
effectively as possible. However, if
you require the laundry to be drier or
damper, you can alter all the drying
levels for one of these programmes at
the same time.
Options
factory default
cool down time 2 min. longer
cool down time 4 min. longer
cool down time 6 min. longer
cool down time 8 min. longer
cool down time 10 min. longer
cool down time 12 min. longer
cool down time 14 min. longer
cool down time 16 min. longer
cool down time 18 min. longer
Options
very damp
even damper
damper
factory default
drier
even drier
very dry
Buzzer volume
The buzzer can be set so that it is
louder.
Exception:
The Cottons programme will
remain unchanged.
Factory default
Buzzer louder
Keypad tone
When this function is activated a tone
will sound each time a button is
pressed.
The volume of the keypad tone will
depend on the setting selected for "
Buzzer volume".
Options
Factory default: off
Keypad tone on
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Code
Conductivity
The code prevents your dryer being
used without your knowledge.
This programmable function
should only be set if the residual
moisture reading in your laundry is
incorrect due to extremely soft water.
When the code has been activated, you
have to enter a code after switching the
dryer on. Otherwise the dryer cannot be
operated.
Conditions
This programmable function should
only be set if the water used for
washing the laundry is extremely soft
with a conductivity reading (electrical
conductivity) less than 150 μS. Contact
your local water authority for the
conductivity level of your mains water
supply.
Options
Factory default: off
Code on
If option has been selected, after
switching on you will have to enter the
code before you can operate the dryer.
To use the dryer when the code is
activated
Only activate this programmable
function for the conditions described
above.
Otherwise drying results can be
unsatisfactory.
After the dryer has been switched on,
will flash in the time display.
The code is and cannot be altered.
Touch the sensor until a
Options
flashes in the first position.
Factory default: off
Low conductivity
Confirm this by pressing the Start/
Stop button.
Enter the two other numbers in the
same way.
The dryer is ready for use after has
been entered and confirmed.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Additional drying levels
You can activate additional drying
levels for many of the programmes:
Normal+ (drier than the Normal drying
level);
Slightly dry (damper than Normal
drying level);
Hand iron (damper than the Hand
iron drying level).
This programmable function is only
available for programmes with a
selectable drying level.
Options
Factory default
Drying level stages added
Once this programmable function
has been activated, you will have the
option of selecting the additional
drying levels when you select a
programme.
Select a programme with selectable
drying levels.
Touch the sensor until two drying
levels light up in the display:
if 2 drying levels then the following
are lit up
additional drying level is
selected
Extra dry
Normal
Normal+
Normal
Hand iron
Slightly dry
Hand iron
Hand iron
Machine iron
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
To switch the display and buttons back
on again
Standby
To save energy the display and
– Turn the programme selector or press
a button. Neither will have any effect
if a programme is running.
buttons will go out after 10 minutes
and only the Start/Stop button will
flash slowly. You can alter this setting.
– Open the door while the dryer is
switched on.
However, standby mode will not occur
in the event of a fault.
Options
Standby switched on:
The display and buttons will go
out after 10 minutes . .
. . . if no selection is made after
switching the dryer on.
. . . after a programme has
started.
However, the display and buttons
will remain lit up for 10 minutes
after a delay start time has
elapsed, after the end of the
programme or at the end of the
anti-crease phase. The buzzer, if
selected, will sound for 10
minutes after the end of the
programme.
Not in current programme
(factory default setting)
As described under .
However, the display and buttons
will remain lit up during the
programme.
Off
The display and buttons will
remain lit up while the dryer is
switched on.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Automatic switch-off
Memory
To save energy the dryer will switch
off automatically after 15 minutes. You
can lengthen or shorten the time.
The electronics will store in memory a
drying level or options for a selected
programme. The duration selected for
a timed drying programme will also be
stored in memory. These settings will
then appear the next time the
However, there is no automatic switch-
off in the event of a fault.
programme is chosen.
The dryer will switch off automatically
after 15 minutes,
Options
– if no further selection is made after
switching the dryer on.
Factory default: Memory off
Memory on
– at the end of the anti-crease phase.
Exception:
– after a programme without an anti-
crease phase has finished.
The Cottons programme will
remain unchanged.
Options
Anti-crease
Switch-off after 10 minutes
Factory default: Switch-off after
15 minutes
If you have pressed the Anti-crease
button: the drum will continue to
rotate in a special anti-crease rhythm
for a maximum of 2 hours after the
end of the drying process. This helps
prevent creasing if laundry is not
going to be removed immediately. You
can reduce the duration of the anti-
crease phase.
Switch-off after 20 minutes
Options
1 hour anti-crease
Factory default: 2 hour anti-
crease
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: [email protected]
Malaysia
Miele Sdn Bhd
Suite 12-2, Level 12
Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1, Jalan Dutamas 1
50480 Kuala Lumpur, Malaysia
Phone: +603-6209-0288
Fax: +603-6205-3768
Australia
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353
New Zealand
Miele New Zealand Limited
IRD 98 463 631
China
Level 2, 10 College Hill
Freemans Bay, Auckland 1011, NZ
Tel: 0800 464 353
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
Singapore
Miele Pte. Ltd.
163 Penang Road
# 04 - 03 Winsland House II
Singapore 238463
Tel: +65 6735 1191, Fax: +65 6735 1161
E-Mail: [email protected]
Miele (Hong Kong) Limited
41/F - 4101, Manhattan Place
23 Wang Tai Road
Kowloon Bay, Hong Kong
Tel: (852) 2610 1331, Fax: (852)2610 1013
Email: [email protected]
South Africa
Miele (Pty) Ltd
India
63 Peter Place, Bryanston 2194
P.O. Box 69434, Bryanston 2021
Tel: (011) 875 9000, Fax: (011) 875 9035
E-mail: [email protected]
Miele India Pvt. Ltd.
Ground Floor, Copia Corporate Suites
Plot No. 9, Jasola
New Delhi - 110025
Tel: 011-46 900 000, Fax: 011-46 900 001
United Arab Emirates
Miele Appliances Ltd.
P.O. Box 11 47 82
Gold & Diamond Park, Sheikh Zayed Road
Building 6 / Offices Nos. 6-214 to 6-220
Dubai
Tel: +971-4-341 84 44
Fax: +971-4-341 88 52
E-Mail: [email protected]
Ireland
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus, Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
Manufacturer: Miele & Cie. KG
Carl-Miele-Straße 29, 33332 Gütersloh, Germany
72
Download from Www.Somanuals.com. All Manuals Search And Download.
TKB 340 WP
en-GB
M.-Nr. 10 000 750 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|