NEC Projection Television GT1150 User Manual
LCD Projector  
GT1150  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD Projector  
GT1150  
User’s Manual  
Y
B
R
E
D
N
W
A
O
T
P
/
S
N
O
S
U
T
A
T
T
S
S
U
J
O
D
A
T
U
P
A
M
A
L
E
C
L
E C N  
A
R
U
C
O
S
R
E
T
N
E
S E L E C T  
U
N
E
M
N
R I G H T  
D O W  
L E N S S H I F T  
U P  
L E F T  
Z O O M  
F O C U S  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT INFORMATION  
Precautions  
RF Interference  
Please read this manual carefully before using your NEC GT1150 Pro-  
jector and keep the manual handy for future reference.  
Your serial number is located on the bottom of your GT1150. Record it  
here:  
WARNING  
The Federal Communications Commission does not allow any  
modifications or changes to the unit EXCEPT those specified by  
NEC Technologies in this manual. Failure to comply with this gov-  
ernment regulation could void your right to operate this equip-  
ment.  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules.These limits are designed to provide reasonable protection  
against harmful interference in a residential installation.This equip-  
ment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. How-  
ever, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful inter-  
ference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following mea-  
sures:  
CAUTION  
To turn off main power, be sure to remove the plug from  
power outlet.  
The power outlet socket should be installed as near to  
the equipment as possible, and should be easily acces-  
sible.  
CAUTION  
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED NEC SERVICE  
PERSONNEL.  
•
•
•
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
This symbol warns the user that uninsulated voltage  
within the unit may be sufficient to cause electrical shock.  
Therefore, it is dangerous to make any kind of contact  
with any part inside of the unit.  
•
Consult the dealer or an experienced radio / TV technician for help.  
In UK, a BS approved power cable with moulded plug has a Black (five  
Amps) fuse installed for use with this equipment. If a power cable is not  
supplied with this equipment please contact your supplier.  
This symbol alerts the user that important information  
concerning the operation and maintenance of this unit  
has been provided.The information should be read care-  
fully to avoid problems.  
WARNING  
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO  
RAIN OR MOISTURE.  
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-  
SION CORD OR IN AN OUTLET UNLESS ALLTHREE PRONGS CAN  
BE FULLY INSERTED.  
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-  
PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-  
FIED NEC SERVICE PERSONNEL.  
DOC Compliance Notice  
This Class B digital apparatus meets all requirements of the Canadian  
Interference-Causing Equipment Regulations.  
3. GSGV Acoustic Noise Information Ordinance:  
The sound pressure level is less than 70 dB (A) according to ISO 3744  
or ISO 7779.  
• IBM is a registered trademark of International Business Machines  
Corporation.  
• Macintosh and PowerBook are registered trademarks of Apple Com-  
puter, Inc.  
• Other product and company names mentioned in this user's manual  
may be the trademarks of their respective holders.  
E – ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INFORMATIONS IMPORTANTES  
Précautions  
Veuillez lire ce manuel avec attention avant d’utiliser votre projecteur  
NEC GT1150 et gardez ce manuel à portée de main afin de pouvoir y  
recourir facilement.  
Votre numéro de série est situé sur le fond de votre GT1150.Reportez-  
le ici:  
ATTENTION  
Pour couper complètement l’alimentation, retirez la prise  
du secteur.  
La prise du secteur doit être accessible et installée le  
plus près possible de l’appareil.  
ATTENTION  
POUR ÉVITER TOUT CHOC ÉLECTRIQUE, N’OUVREZ PAS LE  
BOÎTIER.LES PIÈCES INTERNES NE SONT PAS RÉPARABLES  
PAR L’UTILISATEUR. POUR TOUTE RÉPARATION, ADRESSEZ-  
VOUS À UN RÉPARATEUR AGRÉE NEC.  
Ce symbole avertit l’utilisateur que le contact avec  
certaines parties non isolées à l’intérieur de l’appareil  
risque de causer une électrocution.Il est donc dangereux  
de toucher quoi que ce soit à l’intérieur de l’appareil.  
Ce symbole avertit l’utilisateur que d’importantes infor-  
mations sont fournies sur le fonctionnement ou l’entretien  
de cet appareil. Ces informations doivent être lues  
attentivement pour éviter tout problème.  
AVERTISSEMENT  
AFIN DE PREVENIR TOUT RISQUE D’INCENDIE OU DE CHOC  
ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À  
L’HUMIDITÉ. N’UTILISEZ PAS LA PRISE AVEC TERRE DE  
L’APPAREIL AVEC UNE RALLONGE OU UNE AUTRE PRISE, A  
MOINS QUE LES TROIS BROCHES PUISSENT ÊTRE  
COMPLETEMENT INSÉRÉES. N’OUVREZ PAS LE BOÎTIER. A  
L’INTÉRIEUR SE TROUVENT DES COMPOSANTS À HAUTE TEN-  
SION. TOUTE RÉPARATION DOIT ÊTRE FAITE PAR DU PERSON-  
NEL AGRÉE NEC.  
DOC avis de conformation  
Cet appareil numérique de la classe B respecte toutes les exigences  
du Règlement sur le Matériel Brouilleur du Canada.  
3. Réglement sur les informations concernant les nuisances acoustiques GSGV:  
Le niveau de pression sonore est inférieur à 70 dB (A) conformément  
à la norme ISO 3744 ou ISO 7779.  
• IBM est une marque déposées de International Business Machines  
Corporation.  
• Macintosh et PowerBook sont des marques déposées de Apple Com-  
puter, Inc.  
• Tous les autres marques et les noms de produits sont des marques  
de fabrique ou des marques déposées de leurs compagnies  
respectives.  
E – iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards  
Lamp Replacement  
These safety instructions are to ensure the long life of your projector  
and to prevent fire and shock. Please read them carefully and heed all  
warnings.  
• To replace the lamp, follow all instructions provided on page E-58.  
• Be sure to replace the lamp when the message "The Lamp has  
reached the end of its usable life. Please replace the lamp."  
appears. If you continue to use the lamp after the lamp has reached  
the end of its usable life, the lamp bulb may shatter, and pieces of  
glass may be scattered in the lamp case. Do not touch them as the  
pieces of glass may cause injury. If this happens, contact your NEC  
dealer for lamp replacement.  
Installation  
1. For best results, use your projector in a darkened room.  
2. Place the projector on a flat, level surface in a dry area away from  
dust and moisture.  
3. Do not place your projector in direct sunlight, near heaters or heat  
radiating appliances.  
4. Exposure to direct sunlight, smoke or steam can harm internal com-  
ponents.  
5. Handle your projector carefully. Dropping or jarring can damage in-  
ternal components.  
6. Do not place heavy objects on top of the projector.  
7. If you wish to have the projector installed on the ceiling:  
a. Do not attempt to install the projector yourself.  
• Allow a minimum of ONE minute to elapse after turning off the pro-  
jector. Then disconnect the power cable and allow 60 minutes to  
cool the projector before replacing the lamp.  
Fire and Shock Precautions  
1. Ensure that there is sufficient ventilation and that vents are unob-  
structed to prevent the build-up of heat inside your projector. Allow  
at least 3 inches (10 cm) of space between your projector and a  
wall.  
b. The projector must be installed by qualified technicians in order to ensure  
proper operation and reduce the risk of bodily injury.  
c. In addition, the ceiling must be strong enough to support the projector  
and the installation must be in accordance with any local building codes.  
d. Please consult your dealer for more information.  
2. Prevent foreign objects such as paper clips and bits of paper from  
falling into your projector. Do not attempt to retrieve any objects that  
might fall into your projector. Do not insert any metal objects such as  
a wire or screwdriver into your projector. If something should fall into  
your projector, disconnect it immediately and have the object re-  
moved by a qualified NEC service personnel.  
3. Do not place any liquids on top of your projector.  
• Do not look into the lens while the projector is on. Serious damage  
to your eyes could result.  
• Keep any items such as magnifying glass out of the light path of the  
projector.The light being projected from the lens is extensive, there-  
fore any kind of abnormal objects that can redirect light coming out  
of the lens, can cause unpredictable outcome such as fire or injury  
to the eyes.  
• Do not cover the lens with the supplied lens cap or equivalent while  
the projector is on. Doing so can lead to melting of the cap and  
possibly burning your hands due to the heat emitted from the light  
output.  
Power Supply  
1. The projector is designed to operate on a power supply of 100-120  
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this  
requirement before attempting to use your projector.  
2. Handle the power cable carefully and avoid excessive bending. A  
damaged cord can cause electric shock or fire.  
3. If the projector is not to be used for an extended period of time,  
disconnect the plug from the power outlet.  
Cleaning  
1. Unplug the projector before cleaning.  
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,  
use a mild detergent. Never use strong detergents or solvents such  
as alcohol or thinner.  
4. When using a LAN cable:  
For safety, do not connect to the connector for peripheral device  
wiring that might have excessive Voltage.  
3. Use a blower or lens paper to clean the lens, and be careful not to  
scratch or mar the lens.  
CAUTION  
Do not unplug the power cable from the wall outlet under any one  
of the following circumstances. Doing so can cause damage to  
the projector:  
•
•
While the Hour Glass icon appears.  
While the message "Please wait a moment." appears. This message  
will be displayed after the projector is turned off.  
•
•
Immediately after the power cable is plugged into the wall outlet (the  
POWER indicator has not changed to a steady orange glow).  
Immediately after the cooling fan stops working (The cooling fan con-  
tinues to work for ONE minute after the projector is turned off with the  
POWER button).  
•
While the POWER and the STATUS indicators are alternately flashing.  
CAUTION  
•
Do not put the projector on its side when the lamp is turned on.  
Doing so may cause damage to the projector.  
Before shipping this projector, remove the lens and attach the lens  
hood cap.  
•
The Lens Shift mechanism may encounter damage caused by improper  
handling during transportation.  
E – iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mesures de sécurité importantes  
Remplacement de la lampe  
Ces instructions de sécurité garantissent la longévité de votre projecteur  
et préviennent les risques d’incendie et de décharge électrique. Lisez-  
les et respectez les conseils.  
• Effectuez le remplacement de la lampe en fonction des instructions  
de la page E-60.  
• Assurez-vous de remplacer la lampe lorsque le message “La lampe  
a atteint sa durée de vie maximum, prière de la remplacer.”  
apparaît. Si vous continuer à l ’utiliser au-delà de sa durée de vie,  
celle-ci risque d’exploser et de répandre des fragments de verre à  
l’intérieur du boîtier.  
Ne les touchez pas car elles peuvent vous blesser. Dans ce cas,  
contactez votre revendeur NEC afin de procéder au remplacement  
de la lampe.  
• Attendez au minimum UNE minute aprés avoir éteint la lampe avant  
de la rallumer.  
Une haute tension est immédiatement appliquée à la lampe quand  
celle-ci est mise sous tension.  
Installation  
1. Pour de meilleurs résultats‚ utilisez votre projecteur dans une pièce sombre.  
2. Placez le projecteur sur une surface plane et à niveau, dans un  
endroit sec à l’abri de la poussière et de l’humidité.  
3. Ne placez pas votre projecteur en plein soleil‚ à côté d’appareils de  
chauffage ou d’appareils dégageant de la chaleur.  
4. L’exposition en plein soleil‚ la fumée ou la vapeur peuvent  
endommager des composants internes.  
5. Manipulez votre projecteur avec précaution. Une chute ou un choc  
peuvent endommager des composants internes.  
6. Ne placez pas d’objets lourds sur le projecteur.  
7. Si vous voulez installer le projecteur au plafond:  
a. N’essayez pas d’installer le projecteur vous-même.  
b. Le projecteur doit être installé par un technicien qualifié pour garantir une  
installation réussie et réduire le risque d’éventuelles blessures corporelles.  
c. De plus le plafond doit être suffisamment solide pour supporter le  
projecteur et l’installation doit être conforme aux réglementations locales  
de construction.  
Par conséquent, éteindre, puis tout de suite rallumer peut réduire la  
durée de vie de votre lampe et endommager votre projecteur.  
Précautions contre les risques d’incendie et de  
décharge électrique  
1. Assurez-vous que la ventilation est suffisante et que les trous  
d’aération ne sont pas obstrués afin d’éviter tout échauffement à  
l’intérieur de votre projecteur. Laissez au-moins 3 pouces (10 cm)  
d’espace entre le projecteur et le mur.  
d. Veuillez consulter votre revendeur pour de plus amples informations.  
2. Evitez de faire tomber dans le projecteur des objets étrangers comme  
des trombones ou des morceaux de papier. N’essayez pas de  
récupérer tout objet tombé à l’intérieur de votre projecteur.N’insérez  
pas d’objets métalliques comme du fil de fer ou un tournevis dans  
votre projecteur. Si quelque chose est tombée à l’intérieur de votre  
projecteur, débranchez-le immédiatement et faites retirer l’objet par  
une personne qualifiée de la maintenance NEC.  
Alimentation  
1. Ce projecteur est conçu pour fonctionner avec une alimentation  
électrique de 100-120 ou 200-240 V 50/60 Hz. Assurez-vous que  
votre alimentation correspond à ces critères avant d’essayer d’utiliser  
votre projecteur.  
2. Manipulez le câble d’alimentation avec précaution et évitez de  
l’entortiller. Tout câble endommagé peut provoquer une décharge  
électrique ou un incendie.  
3. Si le projecteur ne doit pas être utilisé pendant longtemps,  
débranchez la prise de la source d’alimentation.  
3. Ne placez aucun liquide sur votre projecteur.  
Avertissements  
• Ne regardez pas à l’intérieur de l’objectif lorsque le projecteur est  
en marche. Vous risquez de vous blesser gravement aux yeux.  
• Maintenez tout ce qui s’apparente à une loupe en dehors du faisceau  
lumineux du projecteur. La lumière projetée par l’objectif est très  
puissante, de sorte que tout objet en opposition pourrait dévier le  
faisceau provenant de l’objectif, ce qui pourrait avoir des  
conséquences imprévues telles qu’un incendie ou une lésion  
occulaire.  
Nettoyage  
1. Débranchez le projecteur avant de procéder au nettoyage.  
2. Nettoyez régulièrement le coffret avec un chiffon humide. Si celui-ci  
est très sale, utilisez un détergent doux. N’utilisez jamais de  
détergents puissants, de l’alcool ou d’autres solvants.  
• Ne bouchez pas l’objectif avec son couvercle fourni lorsque le  
projecteur est allumé. Faire cela pourrait faire fondre le couvercle et  
peut-être brûler vos mains à cause de la châleur émise par le faisceau  
lumineux.  
• Ne tenez pas de pièces de l’objectif. Faire cela pourrait entraîner un  
risque de blessure.  
3. Utilisez un ventilateur ou un papier à objectif pour nettoyer l’objectif  
et faîtes attention de ne pas rayer ou d’abîmer l’objectif.  
Information importante  
Ne pas débrancher le câble d’alimentation de la prise du secteur dans  
les circonstances suivantes car cela risque d’endommager le projecteur:  
* Lorsque l’icone Hour Glass (vitre d’heure) apparaît.  
* Lorsque le message "Veuillez patientez un instant" apparaît. Ce mes-  
sage sera affiché après que le projecteur soit éteint.  
* Immédiatement après que le cordon d’alimentation électrique ait été  
branché sur la prise du mur (l’indicateur POWER n’est pas encore  
devenu orange).  
* Immédiatement après que le ventilateur de refroidissement de soit arrêté  
de fonctionner (le ventilateur de refroidissement continue à fonctionner  
pendant UNE minute après l’extinction du projecteur grâce à  
l’interrupteur POWER OFF).  
* Lorsque les indicateurs POWER (alimentation électrique) et STATUS  
(état) clignotent alternativement.  
ATTETION  
•
Ne pas placer le projecteur sur le côté lorsque la lampe est allumée,  
sinon le projecteur risque d’être endommagé.  
•
Avant d’expedier ce projecteur, veuillez démonter l’objectif et fixer le  
bouchon d’objectif.  
Le mécanisme de déplacement de l’objectif pourrait être endommagé  
durant le transport à la suite d’une manipulation maladroite.  
E – v  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
CTR Adjustment ................................................................................. E-44  
1. INTRODUCTION  
HD Delay ............................................................................................ E-44  
Factory Default ................................................................................... E-44  
Projector Options ....................................................................................... E-44  
Timer (On/Off Timer/Sleep Timer) ...................................................... E-44  
Menu ................................................................................................... E-45  
Menu Mode ......................................................................................... E-45  
Language ............................................................................................ E-45  
Menu Display Time ............................................................................. E-45  
Display Select ..................................................................................... E-46  
Date Format ........................................................................................ E-46  
Date, Time Preset ............................................................................... E-46  
Projector Pointer ................................................................................. E-46  
Direct Button (Volume Bar and Keystone Bar) .................................... E-46  
Setup .................................................................................................. E-47  
Orientation .......................................................................................... E-47  
Background ......................................................................................... E-47  
PC Card Viewer Options ..................................................................... E-47  
Capture Options.................................................................................. E-47  
Signal Select ....................................................................................... E-47  
Signal Select(RGB connector) ........................................................... E-48  
Auto Adjust (RGB only) ....................................................................... E-48  
Auto Start ............................................................................................ E-48  
Power Management ............................................................................ E-48  
Power Off Confirmation ...................................................................... E-48  
Keystone Save .................................................................................... E-48  
Fan High Speed Mode ........................................................................ E-48  
Built-in Speaker .................................................................................. E-48  
Clear Lamp Hour Meter ...................................................................... E-48  
Clear Filter Usage ............................................................................... E-48  
Remote Sensor ................................................................................... E-49  
S-Video Mode Select .......................................................................... E-49  
Communication Speed ....................................................................... E-49  
Projector ID ......................................................................................... E-49  
Default Source Select ......................................................................... E-49  
Link Mode ........................................................................................... E-49  
Switcher Control ................................................................................. E-49  
Tools ........................................................................................................... E-50  
Capture ............................................................................................... E-50  
PC Card Files ..................................................................................... E-50  
Changing Background Logo ............................................................... E-50  
Help ............................................................................................................ E-51  
Contents ............................................................................................. E-51  
Information .......................................................................................... E-51  
Test Pattern ................................................................................................ E-51  
Using the PC Card Viewer Function .......................................................... E-52  
Features .............................................................................................. E-52  
Inserting and Ejecting a PC Card ....................................................... E-52  
Installing the PC Card Viewer Software .............................................. E-53  
Starting Up the PC Card Viewer Software on your PC  
What's in the Box? ....................................................................................... E-1  
Getting to Know Your GT1150 Projector ...................................................... E-2  
Attaching the lens hood cap to the lens hood  
with the supplied string and rivet ............................................... E-4  
Carrying the Projector ........................................................................... E-4  
Top Features ......................................................................................... E-5  
Front Terminal Panel (Right) ................................................................. E-6  
Front Terminal Panel (Left).................................................................... E-7  
PC Card Viewer .................................................................................... E-7  
Remote Control Features ..................................................................... E-8  
Remote Control Precautions ....................................................... E-10  
Remote Control Battery Installation............................................. E-10  
Operating Range for Wireless Remote Control ........................... E-10  
Using the Remote Control in Wired Operation ............................ E-11  
2. INSTALLATION  
Setting Up Your GT1150 Projector ............................................................. E-12  
Screen Size and Projection Distance ......................................................... E-12  
Lens Shift Adjustable Range ...................................................................... E-13  
Optional Lens Installation ........................................................................... E-14  
Setting up for Double Stacking in Link Mode ............................................. E-16  
Projector Orientation .................................................................................. E-17  
3. Basic Operation  
Connecting the Power Cable and Turn on the Projector ............................ E-19  
About Startup Screen ................................................................................ E-20  
Set up the projector .................................................................................... E-21  
Other adjustments ...................................................................................... E-22  
4. CONNECTIONS  
When used in standalone operation .......................................................... E-23  
Connecting Your VCR Or Laser Disc Player ....................................... E-23  
Connecting Your DVD Player with Component Output........................ E-24  
Connecting Your PC Or Macintosh Compute ...................................... E-25  
Connecting an External Monitor ......................................................... E-26  
Connecting a PC with DVI output ....................................................... E-26  
Connecting to a Single Workstation .................................................... E-27  
Ferrite Core Installation ............................................................... E-27  
When Used with One Switcher (ISS-6020/ISS-6020G) ............................. E-28  
When Used with Two or More Switchers (100 Inputs) ............................... E-29  
How to make connections .................................................................. E-29  
Set the DIP switch (S8601) of the Switcher as follows ....................... E-30  
REMOTE 1 Connector ........................................................................ E-31  
Operating Multiple Projector with Remote Control ..................................... E-33  
Using the PC CONTROL connectors ......................................................... E-34  
5. OPERATION  
General Controls ........................................................................................ E-35  
Using the Menus ........................................................................................ E-35  
Using the Magnifying Glass Icon ............................................................... E-35  
Customizing Basic/Custom Menu .............................................................. E-36  
List of Direct Button Combinations ............................................................. E-37  
Menu Tree .................................................................................................. E-38  
Menu Elements .......................................................................................... E-39  
Menu Descriptions & Functions ................................................................. E-40  
Source Select ............................................................................................. E-40  
Entry List .................................................................................................... E-40  
Picture ........................................................................................................ E-41  
Brightness/Contrast/Color/Hue/Sharpness  
(PC Card Viewer Utility 10) ................................................................. E-53  
Operating the PC Card Viewer Function from the Projector  
(playback) ........................................................................................... E-54  
Capturing Images Displayed on the Projector .................................... E-56  
Viewing Digital Images ....................................................................... E-56  
Uninstalling the PC Card Viewer Software ......................................... E-57  
6. MAINTENANCE  
Replacing the Lamp ................................................................................... E-58  
Cleaning or Replacing the Filter ................................................................. E-59  
Remplacement de la lampe ....................................................................... E-60  
Nettoyage ou remplacement du filtre ......................................................... E-61  
Volume ....................................................................................................... E-41  
Image Options ............................................................................................ E-42  
Keystone ............................................................................................. E-42  
Color Temperature .............................................................................. E-42  
Lamp Mode ......................................................................................... E-42  
Gamma Correction ............................................................................. E-42  
Aspect Ratio ....................................................................................... E-42  
Noise Reduction ................................................................................. E-42  
Color Matrix ........................................................................................ E-43  
White Balance..................................................................................... E-43  
Switcher Gain ..................................................................................... E-43  
Position/Clock ..................................................................................... E-43  
Resolution ........................................................................................... E-43  
Video Filter.......................................................................................... E-44  
Overscan ............................................................................................ E-44  
Clamp Timing ...................................................................................... E-44  
Y/C Delay ............................................................................................ E-44  
YTR Adjustmen................................................................................... E-44  
7. TROUBLESHOOTING  
Power / Status Light Messages .................................................................. E-62  
Lamp Light Messages ................................................................................ E-62  
Common Problems & Solutions ................................................................. E-62  
8. SPECIFICATIONS  
Optical/Electrical ........................................................................................ E-64  
Mechanical ................................................................................................. E-65  
Cabinet Dimensions ................................................................................... E-66  
Optional Accessories ................................................................................. E-66  
D-Sub Pin Assignments ............................................................................. E-67  
List of Menu Items Available in Link Mode ................................................. E-68  
Timing Chart .............................................................................................. E-69  
PC Control Codes ...................................................................................... E-70  
Cable Connection ...................................................................................... E-70  
Gravity Stack .............................................................................................. E-70  
E – vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. INTRODUCTION  
What's in the Box?  
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.  
Please save the original box and packing materials if you ever need to ship your GT1150 Projector.  
NOTE: Lenses are optional. Order lenses from your NEC dealer.  
Y
B
R
E
D
N
W
A
O
T
P
/
S
N
O
S
U
T
GT1150 Projector  
A
T
T
S
S
U
J
O
D
A
T
U
P
A
M
A
L
E
C
L
C
E C N  
A
R
U
C
O
S
R
E
T
T
N
L E  
E
S E  
U
N
E
M
T
I G H  
R
N
W
O
D
T
I F  
H
S
S
N
L E  
P
U
T
F
O M  
E
O
L
Z
S
U
C
O
F
String and rivet  
Lens hood cap  
Remote control and batteries (AAA x 2)  
Ferrite clamp core for a commercially  
available BNC cable  
(For RGB 2 connector. See page E-27  
for installation instructions.)  
RGB signal cable  
(15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector)  
Remote cable  
Power cable for Europe (AC 220-240V)  
Power cable for North America (AC 120V)  
Power cable for Japan (AC 100V)  
User’s manuals  
(Japanese and English/German)  
CD-ROM  
E – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting to Know Your GT1150 Projector  
Controls  
Y
B
R
E
D
N
W
A
O
T
P
/
S
N
O
Lens hood  
S
U
T
A
T
T
S
S
U
J
O
D
A
T
U
P
A
M
A
L
E
C
L E C  
R
N
A
U
C
O
S
R
E
T
T
C
E
L
N
E
E
S
PC Card slot  
U
N
E
M
T
H
I G  
N
R
W
O
D
T
Open the cover to access  
the PC card slot.  
I F  
H
S
S
N
E
L
M
P
T
F
O
U
O
E
L
Z
S
U
C
O
F
Remote sensor  
Terminal panel (Left)  
IN  
P
C
C
O
N
T
R
O
L
O
U
T
R
E
M
O
T
E
1
L
Remote sensor  
/
/
M
M
O
O
R
N
N
G
O
B
AC INPUT  
Connect the supplied power  
cable’s three-pin plug here.  
M
O
N
IT  
O
R
R
O
U
T
1
R
G
B
2
Ventilation (outlet)  
R
/
C
r
V
G
H
I
/
Y
D
E
O
1
B
V
/
C
b
V
I
D
E
O
/H  
2
L
/M  
V
R
R
L
/
M
O
N
O
Built-in Security Slot ( )*  
Foot (four)  
L
/
M
S
O
-
V
N
I
O
D
E
O
R
A
U
D
I
O
O
U
T
Rotate to fine-adjust the height of each foot.  
Lens (optional)  
Terminal panel (Right)  
Lens hood cap  
*NOTE: Slot for Kensington MicroSaver Security System  
This security slot supports the MicroSaver® Security System.  
MicroSaver® is a registered trademark of Kensington Microware Inc. The logo  
is trademarked and owned by Kensington Microware Inc.  
E – 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Depression for foot (4 locations)  
F
O
C
U
S
Z
L
E
O
F
U
P
O
T
M
L
E
N
S
S
H
IF  
T
D
O
W
R
IG  
N
H
T
M
E
N
U
S
E
E
L
N
E
C
T
T
E
R
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/S  
T
Remote sensor  
P
O
A
N
W
E
D
R
B
Y
Carrying handle  
Lamp cover  
Speaker (Left)  
Remote sensor  
Speaker (Right)  
IN  
P
C
C
O
N
T
R
O
O
L
U
T
R
E
IN  
M
O
T
REMOTE  
E
1
2
O
U
S
T
C
,
T
A
R
C
IG  
IN  
G
E
R
Air filter  
2
O  
M O
O  
2
R
R G B  
1
R
G / Y  
H / H V  
B / C b  
L / M O N O  
V
Ventilation (inlet)  
R
E – 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attaching the lens hood cap to the lens hood with the supplied string and rivet  
Lens hood cap  
1. Thread the string through the hole on the lens hood cap.  
String  
2. Use the rivet to attach the string to the bottom of the projector.  
Rivet  
R
U
O
R
r
N
O
R
G
B
R
1
-
/
Y
E
R
N
G
H
B
/
H
1
V
/
Y
D
B
E
/
C
b
H
L
/
H
/
M
V
O
V
N
O
B
/
C
b
L
R
/
M
O
V
N
O
A
R
Carrying the Projector  
Always carry your projector by the handle.  
Ensure that the power cable and any other cables connecting to video sources  
are disconnected before moving the projector.  
When moving the projector or when it is not in use, cover the lens with the  
lens hood cap.  
CAUTION:  
Do not put the projector on its side when the lamp is on.  
Doing so may cause damage to the projector.  
SUORCE  
ATUO  
SATNDBY  
A
/
ON  
PWOER  
U
N
E
L
M
E
ATUS  
C
N
A
C
SELCT  
LMAP  
R
E
T
N
E
RGIHT  
UP  
LNESHIFT  
DWON  
LFET  
ZMO  
FCOUS  
E – 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Top Features  
8
FOCU
4
LEFT  
ZOOM  
5
UP  
6
LENS FT  
3
DOWN  
RIGHT  
10  
2
M
E
N
U
9
SELECT  
E
N
T
E
R
S
O
C
U
R
A
N
C
EL  
C
7
E
L
A
M
P
A
U
A
T
D
O
JU  
S
S
T
T
A
T
U
S
O
N
/S  
T
P
O
A
W
ER  
N
D
B
Y
11  
1
12  
13  
1. Power Button (ON / STAND BY)  
7. Cancel Button  
Use this button to turn the power on and off when the power is sup-  
plied and the projector is in standby mode.  
Press this button to exit “Menus”. Press this button to return the adjust-  
ments to the last condition while you are in the adjustment or setting  
menu.  
NOTE: To turn off the projector, press and hold this button for a minimum of  
two seconds.  
8 Lens Shift Button  
Adjust the lens offset by shifting the projected image position horizon-  
tally and / or vertically.  
2. Auto Adjust Button (RGB only)  
Use this button to adjust Position-H/V and Pixel Clock/Phase for an  
optimal picture. Some signals may not be displayed correctly or take  
time to switch between sources.  
9 Zoom Button  
Zoom the lens in and out.  
3. Source Button  
Use this button to select a video source such as a PC, VCR, DVD  
player or PC Card Viewer (PC card).  
10 Focus Button  
Adjust the lens focus.  
Each time this button is pressed, the input source will change as fol-  
lows:  
11. Lamp Remaining Indicator  
Indicates the lamp remaining amount. See the Lamp Light Messages  
on page E-62 for more details.  
→ RGB1 → RGB2 → Video1 → Video2 → S-Video → DVI digital →  
DVI analog → PC Card Viewer  
12. Status Indicator  
If no input signal is present, the input will be skipped.  
When this is lit red (orange in Eco mode) continually, it‘s warning you  
that the projection lamp has reached the end of its usable life (1500  
hours in High-Bright mode and up to 2000 hours in Eco mode). After  
this light appears, it is advisable to replace the projection lamp as soon  
as possible.(See page E-58 or 60). In addition the message "The lamp  
has reached the end of its usable life. Please replace the lamp." ap-  
pears continually until the lamp is replaced.  
4. Menu Button  
Displays the menu.  
ᮤ ᮣ  
5. Select ▲▼  
/ Volume (+) (-) Buttons  
▲▼: Use these buttons to select the menu of the item you wish to  
adjust.  
If the projector is in Eco mode or something out of the ordinary takes  
place, this indicator is lit or blinks. For example, If this light blinks red  
rapidly, it indicates that the lamp cover is not attached properly or the  
projector is overheated.  
When no menus appear, these buttons work as a volume con-  
trol.  
ᮤ ᮣ  
:
Use these buttons to change the level of a selected menu item.  
ᮣ
A press of the button executes the selection.  
See the Power / Status Light Messages on page E-62 for more details.  
When the menus or the Viewer tool bar is not displayed, these  
ᮤ ᮣ  
buttons can be used to select a slide, or to move the cur-  
13. Power Indicator (  
When this indicator is green, the projector is on; when the indicator is  
orange, it is in standby mode.  
)
sor in Folder List or Slide List.  
When the pointer is displayed, these ▲▼  
the pointer.  
ᮤ ᮣ  
buttons move  
6. Enter Button  
Executes your menu selection and activates items selected from the  
menu.  
E – 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Terminal Panel (Right)  
5. MONITOR OUT Connector (Mini D-Sub 15  
pin)  
You can use this connector to loop your computer  
image an external monitor from either the RGB 1,  
RGB 2 or DVI analog input source.  
DVI  
L/MONO  
L/MONO  
1
R
6. RGB 1 Input Connectors (BNC)  
2
4
Connect R,G,B,H (Horizontal sync) and V (Vertical  
sync) outputs of external equipment such as the NEC  
ISS-6020Switcher.  
If using a component with a combined sync (SYNC)  
output, connect it to the H/V terminal. When using  
luminance and color-difference signals of HDTV and  
DVD, connect Pr/Cr to the R,Y to the G and Pb/Cb  
to the B input of the projector.  
MONITOR OUT  
R
5
RGB 2  
RGB 1  
R/Cr  
3
6
VIDEO 1  
G/Y  
B/Cb  
V
8
7. RGB 1 Audio Input Jacks (RCA)  
L/MONO  
This is your left channel audio input for stereo sound  
coming from the RGB Input 1 source.  
This also serves as your monaural audio input.  
R
VIDEO 2  
L/M
H/HV  
R
R
9
10  
11  
L/MONO  
7
L/MONO  
This is your right channel audio input for stereo sound  
from the RGB Input 1 source.  
S
-
VIDEO  
R
13  
8. VIDEO 1 Input Connector (BNC)  
AUDIO O
Connect a VCR, DVD player, laser disc player, or  
document camera here to project video.  
9. VIDEO 2 Input Connector (RCA)  
Connect a VCR, DVD player, laser disc player, or  
document camera here to project video.  
12  
1. DVI Connector  
10. VIDEO Audio Input Jacks (RCA)  
This connector can be used to accept digital or analog signal output  
from a computer with a DVI connector.  
L/MONO  
This is your left channel audio input for stereo sound coming from the  
VIDEO 1 or VIDEO 2 source.  
2. DVI Audio Input Jacks (RCA)  
This also serves as your monaural audio input.  
R
This is your right channel audio input for stereo sound from the VIDEO  
1 or VIDEO 2 source.  
These are the left channel and the right audio inputs for stereo sound  
coming from the equipment connected to a computer with DVI output.  
L/MONO  
This is your left channel audio input for stereo sound from the equip-  
ment connected to a computer with DVI output.  
The L/MONO jack also serves as your monaural audio input.  
R
11. S-VIDEO Input Connector (Mini DIN 4 pin)  
Here is where you connect the S-Video input from an external source  
such as a VCR or laser disc player.  
This is your right channel audio input for stereo sound from the equip-  
ment connected to a computer with DVI output.  
NOTE: S-Video provides more vivid color and higher resolution than the tradi-  
tional composite video format.  
3. RGB 2 Connector (Mini D-Sub 15 pin)  
12. S-VIDEO Audio Input Jacks (RCA)  
L/MONO  
This is your left channel audio input for stereo sound coming from the  
S-VIDEO source.  
Connect your PC, Macintosh, DVD player withY/Cb/Cr outputs or other  
RGB equipment. The optional Component V. Cable is required for Y/  
Cb/ Cr input connection.  
NOTE: The RGB2 connector does not support the Switcher Control mode.  
This also serves as your monaural audio input.  
R
4. RGB 2 Audio Input Jacks (RCA)  
L/MONO  
This is your right channel audio input for stereo sound from the S-  
VIDEO source.  
This is your left channel audio input for stereo sound coming from the  
RGB Input 2 source.  
13. AUDIO OUT Jacks (RCA)  
This also serves as your monaural audio input.  
R
This is your right channel audio input for stereo sound from the RGB  
Input 2 source.  
You can use this connector to output sound from the currently selected  
input source (RGB 1, RGB 2, VIDEO 1, VIDEO 2, S-VIDEO or DVI  
[digital/analog] ). Output sound level can be adjusted in accordance  
with the sound level of the internal speaker.  
E – 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Terminal Panel (Left)  
PC Card Viewer  
R I G  
D O W N  
L E N S S H I F T  
U P  
L E F T  
Z O O M  
F O C U S  
IN  
Push down to open the PC  
Card Slot cover.  
IN  
TE  
O
2
EM  
R
3
5
4
PC CONTROL  
OUT  
1
OUT  
2
SC, TRIGGER  
8
REMOTE 1  
9
7
AC IN  
6
1. PC CONTROL Connectors (Mini D-Sub 9 pin)  
For system expansion such as PC-Control.  
When the GT1150 is powered OFF the screen trigger stops sending a  
low voltage trigger to the screen controller and the screen will go up.  
IN:  
connect to the external equipment such as PC.  
NOTE: Screen Controllers are supplied and supported by screen manufactures.  
This option is not included with the GT1150 projector.  
OUT: for daisy-chaining multiple projectors and operating them with  
the same external equipment. To do so, connect to a second  
projector’ s IN terminal to relay the input at the IN terminal of the  
first projector until all the projectors are connected.  
NOTE: Do not use this jack for anything other than intended use. Connecting  
the wired remote control to the SC. TRIGGER Mini Jack causes damage to the  
remote control.  
2. REMOTE 1 Connector (Mini D-Sub 15 pin)  
5. Slot for LAN Board (Optional)  
This terminal allows external control of the projector from either the  
Switcher or from an external control. When the Switcher is used, con-  
nect to the REMOTE 1 terminal on the back of the Switcher.  
Use this connector to control the projector on a LAN.The optional LAN  
kit is required when this connector is used. See the instructions in-  
cluded with the optional LAN kit.  
NOTE: This projector is compatible with the ISS-6020 Switcher.  
6. AC IN  
3. REMOTE 2 Mini Jacks  
Connect the supplied power cable’s three-pin plug here.  
Three types of power cable are supplied with this LCD projector: three-  
pin type for U. S. A. and Canada.Two-pin type for Germany and Japan.  
IN:  
wired remote control input.  
OUT: for daisy-chaining multiple projectors and operating them with  
the same remote control. To do so, connect to a second projec-  
tor’ s IN terminal to relay the input at the IN terminal of the first  
projector until all the projectors are connected.  
7. PC Card Slot  
Insert a PC card here.  
4. SC. TRIGGER Mini Jack  
8. PC Card Eject Button  
Press to eject a PC card.  
Screen Trigger- When the GT1150 is powered ON the screen trigger  
output sends a low voltage trigger to the screen controller and the  
screen will go down.  
9. PC Card Access Indicator  
Lights while accessing a PC card.  
Stereo mini cable  
(not supplied)  
Tip (12V)  
Ring (0V)  
Sleave (ground. 0V)  
E – 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. POWER ON Button  
Press this button to turn on the projector when the power is supplied  
and the projector is in standby mode.  
Remote Control Features  
2. POWER OFF Button  
Press and hold this button for a minimum of two seconds to turn off the  
projector.  
POWER  
OFF  
ON  
3. MENU Button  
1
3
4
8
2
5
Press to display the main menu.  
While pressing and holding CTL, press this button to display the Re-  
mote Control ID dialog box to specify the remote control ID. See page  
E-33.  
MENU  
ADDRESS  
BS  
-
+
ENTER  
4. ENTER Button  
Executes the menu selection and activates items selected from the  
menu. When the slider or dialog box is displayed:  
Pressing this button confirms adjustments/setting and returns to the  
previous menu display.  
6
7
ADJUST  
PICTURE WHITE BAL.  
IMAGE  
PROJECTOR  
GHI  
ABC  
DEF  
5. Select (Up/Down/Left/Right) Button  
▲▼: Use these buttons to select the menu of the item you wish to  
1
2
3
adjust.  
JKL  
MNO  
PQR  
When no menus appear, these buttons work as a volume con-  
trol.  
4
STU  
5
VWX  
6
YZ?  
ᮤ ᮣ  
: Use these buttons to change the level of a selected menu item.  
9
ᮣ
A press of the button executes the selection.  
ᮤ
When the menus or theViewer tool bar is not displayed, these  
9
8
7
ᮣ
buttons can be used to select a slide, or to move the cursor in  
10  
,.  
UNDO CANCEL  
Folder List or Slide List.  
0
11  
14  
ᮤ ᮣ  
When the pointer is displayed, these ▲▼  
buttons move the pointer.  
12  
13  
TEST  
INFO.  
HELP  
AUTO  
See page E-35 for displaying the pointer.  
Pressing and holding CTL, then pressing button works as a Back  
Space key in the entry screen.  
ᮤ
15  
16  
18  
19  
POSITION PIXEL  
Pressing and holding CTL, then pressing this button moves the menu,  
slider, toolbar or dialog box.  
17  
LENS  
MUTE  
SHUTTER  
6. ADJUST WHITE BAL Button  
20  
Press to display the color adjustment screen. Pressing this button se-  
quentially selects "ColorTemperature" → "White Balance" → "Switcher  
Gain".  
PICTURE  
KEYSTONE AMPLITUDE ENTRYLIST  
SOUND  
OSD  
21  
22  
23  
R
G
B
MAGNIFY  
7. ADJUST PICTURE Button  
Press to display the Picture screen.  
+
+
25  
24  
8. IMAGE/PROJECTOR Button  
Press to display the Image Options screen.  
-
-
Pressing this button sequentially selects "Gamma Correction" → "As-  
pect Ratio" → "Noise Reduction" → "Color Matrix" → "Resolution" →  
"Video Filter" → "Overscan" → "ClampTiming” → "Y/C Delay" → "YTR  
Adjustment" → "CTR Adjustment" → "HD Delay".  
While pressing and holding CTL, pressing this button rotates "On/Off  
Timer" → "Sleep Timer" → "Menu" → "Setup" → "Link Mode" →  
"Switcher Control" → "LAN mode" (optional).  
FOCUS  
CTL  
ZOOM  
LENS  
26  
9. Source / Alphanumeric Buttons  
Press to select input or to name a signal.  
1 .................. Selects RGB 1 input.  
2 .................. Selects RGB 2 input.  
3 .................. Selects VIDEO 1 input.  
4 .................. Selects VIDEO 2 input.  
5 .................. Selects S-VIDEO 1 input.  
6 .................. Selects DVI digital input.  
7 .................. Selects DVI analog input.  
8 .................. Selects PC Card Viewer.  
9 .................. Selects RGB1 (VIDEO) input  
0 .................. Selects RGB2 (S-VIDEO) input  
E – 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. UNDO  
25. MAGNIFY/ZOOM (+/–)  
Press to return the adjustments and settings to the previous condition.  
While pressing and holding CTL, pressing this button clears the entire  
menus or adjustment/setting screen. At this time the adjustments/set-  
tings are stored in memory except the items on the setting screen with  
"OK" and "Cancel" buttons such as the Menu and the Setup screen.  
Magnify the size of a target portion.  
While pressing and holding CTL, pressing this button allows you to  
zoom the lens in and out.  
26. CTL  
Used in conjunction with other buttons, similar to a shift key on a com-  
puter.  
11. CANCEL  
Press to exit the menu.  
Press this button with CTL to return to the previous menu without clos-  
ing adjustment/setting screen while the menus appear. This feature  
allows you to adjust or set several items concurrently.  
27. Remote Jack  
Connect your remote control cable here for wired operation.  
28. Infrared Transmitter  
12. INFO  
Direct the remote control toward the remote sensor on the projector  
Displays the Information screen.  
cabinet.  
O
R
S
P
4
I M A G E  
D E F  
13. TEST  
J K L  
1
A B C  
2
S
W H I T E B A L .  
S
E
R
E N T E R  
Press to display the test pattern. Pressing this button sequentially se-  
lects nine test patterns.  
D
D
A
A D J U S T  
P I C T U R E  
M E N U  
+
-
O N  
B S  
14. HELP  
Provides online help.  
P O W E R  
O F F  
15. PIXEL  
27  
28  
Displays the Position/Clock screen to adjust the clock and phase.  
16. AUTO (RGB only)  
Press to adjust Position-H/V and Pixel Clock/Phase for an optimal pic-  
ture.  
17. POSITION  
Press to display the Position/Clock screen.  
While pressing and holding CTL, pressing this button displays the Lens  
Shift adjustment screen.  
18. MUTE SOUND  
Turns off the sound for a short period of time. Press again to restore  
the sound.  
19. MUTE OSD  
Press to turn off the on-screen display. Press again to restore the on-  
screen display.  
NOTE: You can also turn off the on-screen display forcefully by pressing and  
holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ;  
doing this again restores it. In this case any adjustment will still change the  
projector's memory settings. This mode is available even when input is switched  
to another or the power is turned off the main power.  
20. MUTE PICTURE  
Press to turn off the picture for a short period of time. Press again to  
restore the picture.  
21. KEYSTONE (R)  
Press to display the Keystone Correction screen.  
When the test pattern is displayed, while pressing and holding CTL,  
pressing this button displays a red test pattern.  
22. AMPLITUDE (G)  
Service personnel only.  
When the test pattern is displayed, while pressing and holding CTL,  
pressing this button displays a green test pattern.  
23. ENTRY LIST (B)  
Press to display the Entry List screen.  
When the test pattern is displayed, while pressing and holding CTL,  
pressing this button displays a blue test pattern.  
24. FOCUS (+/–)  
While pressing and holding CTL, pressing this button allows you to  
adjust the lens focus.  
E – 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Precautions  
Operating Range for Wireless Remote Control  
The infrared signal operates by line-of-sight up to a distance of ap-  
proximately 7m (20 feet) and a 60 degree angle of the remote sensor.  
The projector will not function if there are objects between the remote  
sensor and the remote control or if strong light falls on the remote  
sensor. Weak batteries will also prevent the projector from operating  
properly.  
• The remote control system may not function when direct sunlight or  
strong illumination strikes the remote control sensor of the main unit,  
or when there is an obstacle in the path.  
• When remote control buttons are pressed and held, projector’s func-  
tion keys may not operate.  
• Do not subject to strong shock.  
• Do not allow water or other liquid to splash on the remote control. If  
the remote control gets wet, wipe it dry immediately.  
• Avoid exposure to heat and steam.  
Remote sensors on the projector cabinet  
• Remove the batteries from the remote control when the remote con-  
trol is not going to be used for a long period.  
30˚  
Remote Control Battery Installation  
Installing the Remote Control Batteries  
When it comes time to replace the batteries, two "AAA" type will be  
required.  
7m  
30˚  
Side View  
1. Press and open the cover.  
Remote control  
30˚  
30˚  
2. Align and insert the batteries according to the (+) and (-) indica-  
tions inside the case.  
7m  
NOTE: You cannot operate the projector using the remote control if:  
• The remote control ID is not set to [None].  
• The remote ID is not the same as the projector ID.  
3. Replace the cover.  
See page E-33 for setting remote ID and page E-49 for setting projector ID.  
E – 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control in Wired Operation  
Connect one end of the supplied remote cable to the REMOTE 2 IN  
mini jack and the other end to the remote jack on the remote control.  
A U T O  
H E L P  
I X E L  
I N F O .  
C A N C E L  
IN  
PC CONTRO
OUT  
IN  
9
T
Y Z ?  
U N D O  
6
P Q R  
8
V W X  
0
7 , .  
3
R
T O  
G H I  
O J E C  
P R  
M N O  
S T U  
E
4
5
A G  
I M  
L .  
B A  
I T E  
D E F  
J K L  
H
REMOTE  
2
1
2
S
W
E
E S  
E N T E R  
D R  
A D  
S T  
J U  
A B C  
U R  
T
D
I C  
A
P
M E N U  
+
N
-
O
B S  
R
E
W
O
P
F
OUT  
F
O
REMOTE 1  
SC, TRIGGER  
AC IN  
Remote cable (supplied)  
Terminal panel (Left)  
E – 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. INSTALLATION  
This section describes how to set up your GT1150 projector and how to connect video and audio sources.  
Setting Up Your GT1150 Projector  
Your GT1150 Projector is simple to set up and use. But before you get started, you must first:  
1. Determine the image size  
4. Connect the supplied power cable.  
2. Set up a screen or select a non-glossy white wall onto which you  
can project your image.  
3. Install the optional lens to the projector.  
5. Set up the projector.  
6. Connect a PC, VCR, DVD player, or other equipment.  
7. Make settings or adjustments on the projector.  
Screen Size and Projection Distance  
Applicable lens and throw distance/ List of screen sizes  
List of Screen Sizes  
Screen size  
Width (H)  
Height (V)  
m
0.8  
1.2  
1.6  
2.0  
2.4  
3.0  
4.1  
5.1  
6.1  
8.1  
10.2  
feet  
2.7  
4.0  
5.3  
6.7  
m
feet  
2.0  
3.0  
4.0  
5.0  
40"  
60"  
80"  
0.6  
0.9  
1.2  
1.5  
1.8  
2.3  
3.0  
3.8  
4.6  
6.1  
7.6  
100"  
120"  
150"  
200"  
250"  
300"  
400"  
500"  
Height  
Screen size (Diagonal)  
8.0  
6.0  
7.5  
10.0  
13.3  
16.7  
20.0  
26.7  
33.3  
10.0  
12.5  
15.0  
20.0  
25.0  
Formulas:  
Screen width H (m)= Screen Diagonal (4:3) x 4/5 x 0.0254  
Screen height V (m)= Screen Diagonal (4:3) x 3/5 x 0.0254  
Screen width H (feet)= Screen size x 4/5  
Width  
Table of Throw Distances and Screen Sizes for Optional Lenses  
Screen height V (feet)= Screen size x 3/5  
Lens  
Model  
Magnification  
40"  
GT10RL  
1.0  
GT13ZL  
1.3 – 1.6  
GT19ZL  
1.8 – 2.4  
GT34ZL  
3.4 – 5.2  
0.8 (m)  
1.2 (m)  
1.3 (m)  
1.4 (m)  
1.6 (m)  
1.7 (m)  
1.8 (m)  
2.0 (m)  
2.4 (m)  
3.0 (m)  
3.7 (m)  
4.1 (m)  
4.3 (m)  
4.9 (m)  
5.1 (m)  
5.6 (m)  
6.1 (m)  
–
2.7 (feet)  
4.0 (feet)  
4.4 (feet)  
4.7 (feet)  
5.3 (feet)  
5.5 (feet)  
6.0 (feet)  
6.7 (feet)  
8.0 (feet)  
10.0 (feet)  
12.1 (feet)  
13.3 (feet)  
14.2 (feet)  
16.2 (feet)  
16.7 (feet)  
18.3 (feet)  
20.0 (feet)  
–
1.1-1.3 (m)  
1.6-2.0 (m)  
1.7-2.1 (m)  
1.9-2.3 (m)  
2.1-2.6 (m)  
2.2-2.7 (m)  
2.3-2.9 (m)  
2.6-3.3 (m)  
3.2-3.9 (m)  
4.0-4.9 (m)  
4.7-5.8 (m)  
5.3-6.5 (m)  
5.5-6.8 (m)  
6.3-7.8 (m)  
6.6-8.1 (m)  
7.1-8.8 (m)  
7.9-9.8 (m)  
–
3.5-4.3 (feet)  
1.5-2.0 (m)  
2.2-2.9 (m)  
2.5-3.2 (m)  
2.6-3.5 (m)  
2.9-3.9 (m)  
3.1-4.1 (m)  
3.3-4.3 (m)  
3.7-4.9 (m)  
4.4-5.9 (m)  
5.5-7.3 (m)  
6.7-8.8 (m)  
7.3-9.8 (m)  
7.9-10.3 (m)  
9.0-11.7 (m)  
9.1-12.2 (m)  
10.1-13.2 (m)  
11.0-14.6 (m)  
–
4.8-6.4 (feet)  
–
–
–
–
–
–
–
–
60"  
67"  
72"  
80"  
84"  
90"  
100"  
120"  
150"  
180  
200"  
210"  
240"  
250"  
270"  
300"  
400"  
500"  
5.2-6.4 (feet)  
5.7-7.0 (feet)  
6.1-7.5 (feet)  
6.9-8.5 (feet)  
7.1-8.8 (feet)  
7.7-9.5 (feet)  
8.7-10.7 (feet)  
10.4-12.8 (feet)  
13.0-16.0 (feet)  
15.5-19.1 (feet)  
17.3-21.3 (feet)  
18.1-22.4 (feet)  
20.8-25.6 (feet)  
21.7-26.6 (feet)  
23.4-28.8 (feet)  
26.0-32.0 (feet)  
–
7.2-9.6 (feet)  
8.1-10.6 (feet)  
8.7-11.4 (feet)  
9.6-12.8 (feet)  
10.2-13.3 (feet)  
10.9-14.3 (feet)  
12.0-16.0 (feet)  
14.4-19.2 (feet)  
18.0-24.0 (feet)  
22.1-28.8 (feet)  
24.0-32.0 (feet)  
25.8-33.7 (feet)  
29.6-38.5 (feet)  
30.0-40.0 (feet)  
33.3-43.3 (feet)  
36.0-48.0 (feet)  
–
5.5-8.5 (m)  
5.9-9.0 (m)  
6.3-9.6 (m)  
6.9-10.6 (m)  
8.3-12.7 (m)  
10.4-15.8 (m)  
12.8-19.3 (m)  
13.8-21.1 (m)  
15.0-22.6 (m)  
17.1-25.8 (m)  
17.3-26.4 (m)  
19.3-29.1 (m)  
20.7-31.7 (m)  
27.6-42.3 (m)  
34.5-52.8 (m)  
18.1-27.7 (feet)  
19.3-29.3 (feet)  
20.7-31.4 (feet)  
22.7-34.6 (feet)  
27.2-41.6 (feet)  
34.0-52.0 (feet)  
42.1-63.4 (feet)  
45.3-69.3 (feet)  
49.2-74.0 (feet)  
56.3-84.7 (feet)  
56.6-86.6 (feet)  
63.4-95.3 (feet)  
68.0-103.9 (feet)  
90.6-138.6 (feet)  
113.3-173.2 (feet)  
–
–
–
–
–
–
GT10RL (H
ן
1.0)  
GT34ZL (H
ן
3.4) – (H
ן
5.2)  
Throw distance  
GT13ZL (H
ן
1.3) – (H
ן
1.6)  
GT19ZL (H
ן
1.8) – (H
ן
2.4)  
For screen sizes between 40” and 500” not indicated on the above table, use formulas below.  
Projection Distance = Screen Width (H) x Lens Magnification  
Throw distance for GT10RL lens (m/feet) =H x 1.0 (For H between 0.8 m/2.7feet and 6.1 m/20.0 feet)  
Throw distance for GT13ZL lens (m/feet) =H x 1.3 through H x 1.6 (For H between 1.1 m/3.5 feet and 9.8 m/32.0 feet)  
Throw distance for GT19ZL lens (m/feet) =H x 1.8 through H x 2.4 (For H between 1.5 m/4.8 feet and 14.6 m/48.0 feet)  
Throw distance for GT34ZL lens (m/feet) =H x 3.4 through H x 5.2 (For H between 5.5 m/18.1 feet and 52.8 m/173.2 feet)  
NOTE: Distances may vary +/-5%.  
E – 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lens Shift Adjustable Range  
Lens Shift Range for Desktop and Ceiling Mount  
Application  
Desktop/Front  
Vertical  
The diagram below shows the location of the image position  
in the lens. The lens can be shifted within the shaded area as  
shown using the normal projection position as a starting  
point.  
Note: Lens shift feature is not available on GT10RL (fixed  
lens)  
0.5V  
(0.43V)  
Maximum Possible Range  
for GT19ZL/GT34ZL (GT13ZL):  
Up: 0.5V (0.43V)  
Down: 0.5V (0.43V)  
Right: 0.25H  
Normal Position  
Left: 0.25H  
(H: width of projected image, V: height of projected image)  
Note: If lens is shifted in two directions combined, maximum  
range in either direction cannot be obtained due to rounded  
off area near edge of lens. (example: shift up and right)  
See diagram below.  
Ceiling/Front  
Vertical  
Normal Position  
0.25H  
0.25H  
0.50V  
(0.43V)  
0.50V  
(0.43V)  
0.5V  
(0.43V)  
0.50V  
0.50V  
(0.43V)  
(0.43V)  
Horizontal  
0.25H  
0.25H  
Normal projection  
position  
Normal Position  
0.25H  
E-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Lens Installation  
This section describes how to install the lens.  
Before installation  
* Determine the optional lens to be used to obtain a desired projection distance. There are four optional lenses available:  
GT10RL (Fixed short throw lens)  
GT19ZL, GT13ZL and GT34ZL (Zoom lens)  
* Press the power button (ON/STAND BY) on the projector or POWER OFF button on the remote control, wait ONE minute for the cooling fan to stop, then  
disconnect the power cable.  
Check that the projector has cooled off sufficiently before proceeding.  
CAUTION  
* The projector and lens contain high-precision parts. Do not induce shock to the projector or the lens.  
* Do not touch the lens surface. Doing so can degrade the optical performance.  
Preparation: Tools needed for installation:  
A hexagonal driver and dust-protective sheets are supplied with the optional lens.  
1. Remove the lens hood cap and lens hood.  
1 Press and hold the catches on both ends of the lens hood cap, and 2 then remove it.  
3 Loosen the 4 screws on the lens hood using the hexagonal driver until the hexagonal driver goes into a freewheeling condition and 4 remove  
the lens hood. The 4 screws are not removable.  
I
N
P
I
N
C
C
O
N
T
R
O
L
R
E
M
O
T
E
O
2
U
T
Lens hood  
3
,
L
L
/M  
O
O
R
N
N
G
O
O
B
/M  
M
O
N
IT  
O
R
Lens hood cap  
R
O
U
T
2
R
G
B
1
R
/C  
r
V
ID  
G
/Y  
E
O
1
3
4
B
V
/C  
b
V
ID  
E
O
H
/H  
2
L
V
/M  
3
R
R
L/M  
O
N
O
L
/M  
S
-
O
N
V
ID  
O
E
O
R
A
U
D
IO  
O
U
T
1
3
2
1
2. Remove the dust-protective sheet and replace with the new one.  
1 Remove the dust-protective sheet on the back of the lens hood. 2 Replace it with the dust-protective sheet included with the optional lens.  
Place the dust-protective sheet with the two holes side up while warping it. Be careful not to fold the sheet.  
Dust-protective sheet  
(included with the optional lens)  
Dust-protective sheet  
(on the projector)  
1
Hole  
2
Hole  
Side with aluminum  
Completed  
E – 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Mount the lens unit on the projector and connect the extension cable attached to the projector.  
1 Remove the lens cap from the rear end of the lens unit.  
2 Insert the lens unit so that the 4 screws on the lens unit are properly lined up with the 4 holes on the lens mount.  
3 Secure the 4 screws using the hexagonal driver.  
4 Insert the connector of the lens unit fully into the socket of the extension cable attached to the projector.  
NOTE: Leave the front lens cap for protection while mounting the lens unit.  
Y
B
R
E
D
N
W
A
O
T
/
S
N
O
T
S
U
Y
B
J
R
E
O
D
T
N
W
A
O
T
P
/
S
N
O
S
E
U
C
T
A
R
T
S
T
S
Lens mount  
U
J
O
D
A
T
U
P
A
M
A
L
E
C
N
L
E C  
N
E
R
A
U
C
O
S
R
E
T
N
E
E L E C T  
S
1
U
N
I
E
M
R I G H T  
W N  
D O  
L E N S S H I F T  
F T  
U P  
L E  
Z O O M  
F O C U S  
I
N
P
I
N
I
C
N
C
O
N
T
R
O
L
P
I
N
R
C
E
C
M
O
O
N
T
E
T
O
2
R
O
U
T
L
R
E
M
O
T
E
O
O
2
U
U
T
T
R
2
E
M
O
T
E
1
O
U
S
T
C
R
,
E
T
M
R
I
O
G
T
G
E
E
1
R
S
C
,
T
R
A
I
C
G
G
I
N
E
R
L
L
/M  
O
O
R
N
G
O
B
L
L
/M  
/M  
O
O
R
N
N
G
O
O
B
/M  
R
M
O
N
IT  
O
R
R
O
U
T
3
1
R
O
R
G
U
B
T
2
R
/C  
r
2
R
G
B
2
V
ID  
G
/Y  
E
O
1
R
/C  
r
B
V
/C  
b
V
G
ID  
/Y  
E
V
ID  
O
E
O
H
/
H
V
2
L
/M  
B
V
R
R
H
O
/H  
2
L
/M  
V
L
/M  
O
N
O
R
R
L
/M  
S
-
O
V
ID  
N
O
L
/M  
E
O
O
N
R
O
L
/M  
S
O
N
-
4
V
ID  
O
A
U
E
O
D
IO  
R
O
U
T
A
U
D
IO  
O
U
T
4. Reinstall the lens hood.  
1 Remove the front lens cap from the lens unit.  
2 Insert the lens hood so that the grooves on the 4 corners of the lens hood are properly lined up with the 4 catches on the projector.  
3 Secure the 4 screws using the hexagonal driver.  
This completes installation. 4 If necessary, put the lens hood cap on the lens hood.  
Y
Y
B
R
B
R
E
D
E
D
N
W
N
W
A
O
A
O
T
P
T
P
/
S
/
S
N
N
O
O
S
S
U
U
T
T
A
A
T
S
T
T
T
S
S
S
U
U
J
J
O
O
D
A
D
T
T
A
U
P
U
P
A
A
M
M
A
A
L
L
E
E
C
C
L
C
E C N  
L
C
E C N  
A
R
A
C
R
U
U
C
O
O
S
S
R
R
E
E
T
T
T
T
N
E
N
E
L
E
L
E
E
E
S
S
U
U
N
N
E
E
M
M
T
T
H
H
G
G
I
N
I
N
R
W
R
W
O
O
D
D
T
T
F
F
I
I
H
H
S
S
S
S
N
N
E
E
L
L
M
P
T
F
M
O
P
T
O
U
U
F
O
E
O
E
Z
L
Z
L
S
S
U
U
C
C
O
O
F
F
I
I
N
N
P
I
P
I
N
N
C
C
C
C
O
O
N
N
T
T
R
R
O
O
L
L
R
R
E
E
M
M
O
O
T
T
E
E
2
O
2
O
U
U
T
T
O
U
T
R
E
M
O
T
E
1
S
C
,
T
R
I
I
G
G
E
R
3
3
A
C
I
N
L
L
L
L
/M  
/M  
/M  
O
O
R
O
O
R
N
N
G
N
N
G
O
B
O
B
/M  
M
M
O
O
N
N
IT  
IT  
R
O
R
O
R
R
O
O
U
U
T
T
2
2
R
R
G
G
B
B
1
1
R
R
/C  
/C  
r
r
G
V
G
V
ID  
ID  
/Y  
/Y  
E
E
O
O
1
1
3
3
B
V
B
V
/C  
b
/C  
b
V
V
ID  
ID  
E
H
E
O
H
O
/H  
/H  
2
L
2
L
/M  
V
V
/M  
O
O
1
R
R
R
R
L
L/M  
O
/M  
O
N
N
O
O
L
L
/M  
/M  
O
N
S
O
S
-
V
-
V
N
ID  
O
ID  
O
E
E
O
O
R
R
A
A
U
U
D
D
IO  
IO  
O
O
U
U
T
T
2
Groove  
Catch  
4
E – 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-1-3. Display all desired input signals, make adjustment to each signal,  
then save all adjustments on the master projector. (Adjustments will be  
saved automatically.)  
Setting up for Double Stacking in Link Mode  
Master projector  
3-1-4. Turn the master projector off (standby mode).  
3-1-5. Store all the adjustments on a PC card from the master projector.  
3-1-5-1. Open the PC Card slot cover to access the PC card slot. Insert  
a PC card into this slot.  
3-1-5-2. Press and hold CANCEL, then press POWER on the top panel  
of the master projector. The POWER indicator will change to steady  
green and the PC Card Access indicator will start flashing. After stor-  
ing data on the PC card, the POWER indicator will change to orange.  
Foot  
3-1-5-3. Remove the PC card from the slot of the master projector.  
3-1-6. Transfer the data to the other slave projectors using the PC card so  
that all the projectors have the same data in memory.  
Depression  
for foot  
3-1-6-1. Insert the PC card into the slot of a slave projector.  
NOTE: Since data in the slave projectors will be lost at this time, make  
backup copies of them before proceeding.  
3-1-6-2. Press and hold ENTER, then press MENU on the top panel of  
the slave projector. The POWER indicator will change to steady green  
and the PC Card Access indicator will start flashing to indicate that  
the data is being copied from the PC card to the slave projector. After  
copying data to the slave projector, the POWER indicator will change  
to orange.  
Slave projector  
NOTE: Up to two units can be gravity stacked without external support. In some  
cases, however, two images will not align on the screen correctly. This will  
become more apparent when displaying small text and detailed graphics.  
3-1-6-3. Remove the PC card from the slave projector.  
NOTE: If you select the RGB1 input on the master projector, you must  
select the same input on the slave projector and the RGB2 on the master  
projector and the slave projector.  
CAUTION: To prevent the projectors from falling, install them in a place and  
fasten them in a way with sufficient strength to support the two projectors.  
NOTE: SW 1 Level and SW 2 Level of Switcher Control are not available on Link  
Mode.  
NOTE: After adjusting and registering signals as mentioned above, you  
must change the input to RGB on the Entry Edit Command window for  
Link Mode. See "Entry List Edit" on page E-40 for changing to RGB source.  
For double stacking, follow the instructions described below.  
3-1-6-4. Display the desired source.  
1) Stacking the Projectors  
4) Display the internal crosshatch test pattern.  
1-1. Place the projectors at the proper height for best screen to projec-  
tor relationship. Make sure that all projectors have the same display  
orientation.  
NOTE: Use a different single color for each projector. Example:  
Turn on Green of one projector (master), then Red of the other (slave).  
5) Adjusting the lens shift, zoom and focus to clearly display  
all projected patterns.  
2) Hookup  
2-1. Use the supplied RGB signal cable to connect the RGB output of  
the master projector to the RGB input of the slave projector until all  
the projectors are connected.  
5-1. Adjust the Lens Shift using the LENS SHIFT button on the projec-  
tor cabinet.You can also adjust the Lens Shift by pressing and hold-  
ing CTL and pressing the POSITION button on the remote control.  
For Lens Shift Adjustable Range, see page E-13.  
2-2.Next, using a commercially available, bi-directional RS-232C cable  
connect the PC CONTROL OUT terminal of the master projector to  
the PC CONTROL IN terminal of the slave projector until all the  
projectors are connected.  
5-2. Zoom the lens in and out by using the ZOOM button on the projec-  
tor cabinet or the remote control.  
5-3. Adjust the lens focus by using the FOCUS button on the projector  
cabinet or the remote control.  
2-3. Turn all the projectors on and roughly make some optical adjust-  
ments to each projector.  
NOTE: If the physical (vertical) alignment of the projector is not correct, adjust  
the height of the feet. If there is any keystone distortion, use Keystone adjust-  
ment to correct and save the settings on each projector. See page E-22 and E-  
42 for Keystone correction.  
This completes set-up and adjustments. An image is projected from the master  
projector. See page E-49 for Link mode.  
3) Adjusting and registering signals to be projected in Link  
mode and stack application.  
Signal Data Preparation  
3-1. Create data for the master projector and copy data to the slave  
projector.  
3-1-1. Choose one projector as the master.  
3-1-2. Turn the master projector on.  
E – 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6) Link Mode Setting  
6-1 Assign a unique Projector ID for each projector.  
Projector Orientation  
An image can be projected from in front or behind a screen, and the  
projector can be installed on the ceiling*.  
6-1-1. Select [Projector Options] → [Setup] →[Page 6] → [Projector ID].  
See page E-49 for specifying ID.  
Ceiling Front Projection  
Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to se-  
lect "Ceiling Front". (See page E-47.)  
6-1-2. Specify a unique projector ID for each projector.  
6-2 Select the same communication speed for all the projectors.  
6-2-1. Select [Projector Options] → [Setup] →[Page 6] → [Communica-  
tion Speed]. See page E-49 for setting the communication speed.  
6-2-2. Select the appropriate speed between 4800 and 38400.  
6-3 Set the Link Mode on each projector.  
6-3-1. Select [Projector Options] → [Link Mode].  
6-3-2. First select [Slave] on the slave projector.  
6-3-3. Select [Master] on the master projectors. See page E-49 for setting  
Link Mode.  
NEC  
6-4 Project a source image from all projectors  
6-4-1. Display any signal onto the screen.  
6-4-2. Check to see if the imags on the master projector are displayed in  
syncronization with the ones on the other slave projector while the pro-  
jectors are in link mode.  
Ceiling Rear Projection  
Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to se-  
lect "Ceiling Rear". (See page E-47.)  
NOTE: Registering signals is not possible in the Link mode. To register a  
signal, first set "Link Mode" to "Standalone" on the menu and then repeat  
the above steps from 3. If you select an unregistered signal, the master  
projector displays the image, but the slave projector doesn't. To view the  
information on the currently displayed signal, select [Help] → [Informa-  
tion] → [Page1].  
Transparent screen  
6-5 Make adjustments to the slave projector.  
NOTE: See “List of Menu Items Available on Link Mode” on page E-68 for  
more information.  
6-5-1. Temporarily, change the master projector from Master to Standalone.  
Make sure that the slave projectors are still in Slave mode.  
6-5-2. Display a source you want to adjust from the master projector.  
6-5-3. On the Slave Projector select the same signal From the Entry List  
(same No.) as that of the master projector. Display it from the slave  
projector.  
NEC  
6-5-4. Make Picture adjustment such as brightness, contrast, or color tem-  
perature.  
6-5-5. Change the master projector from Standalone to Master to activate  
the Link Mode  
6-6 This completes the Link Mode adjustment procedure.  
NOTE: The optional lenses for GT1150 have different geometrical distortions in  
wide zoom and tele. Select the best zoom position for stacking where the geo-  
metrical distortion is as small as possible. See page E-70 for the recommended  
throw distances and other notes.  
E – 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Desktop Rear Projection  
Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to se-  
lect "Desktop Rear". (See page E-47.)  
Transparent screen  
R
O
O
/
R
O  
O
L/
1
B
RG  
Cb  
UT  
B/  
TO  
N
M
Y
G/  
V
C
R
H
/  
B
R
R
O
O
/
N
O
O
L/  
I  
N
O
U  
/  
I  
O
I  
O
E  
-I  
NEC  
WARNING  
• Installing your projector on the ceiling must be done by a qualified  
technician. Contact your NEC dealer for more information.  
* Do not attempt to install the projector yourself.  
• Only use your projector on a solid, level surface. If the projector falls  
to the ground, you can be injured and the projector severely dam-  
aged.  
• Do not use the projector where temperatures vary greatly. The pro-  
jector must be used at temperatures between 32˚F (0˚C) and 104˚F  
(40˚C).  
• Do not expose the projector to moisture, dust, or smoke. This will  
harm the screen image.  
• Ensure that you have adequate ventilation around your projector so  
heat can dissipate. Do not cover the vents on the projector.  
E – 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. BASIC OPERATION  
Connecting the Power Cable and Turn on the Projector  
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.  
1. Connect the supplied power cable to the projector.  
Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange.  
R
I
O
N
O
R
M
/
1
B
G
b
C
/
B
V
I
Y
/
V
/
R
O
N
O
I
T
U
O
O
I
I
N
I
N
I
E
T
O
2
M
E
R
L
O
R
T
N
O
C
C
P
T
U
O
T
U
O
R
E
G
G
I
R
T
,
C
S
1
E
T
O
M
E
R
N
I
C
A
2. Turn on and off the Projector.  
FT  
UP  
LENS SHIFT  
Power "ON/STAND BY" button  
OWN  
RIGHT  
POWER  
OFF  
ON  
M
E
N
U
SELECT  
E
N
T
E
R
MENU  
S
O
C
U
R
A
N
C
EL  
C
E
ADDRESS  
L
A
BS  
M
P
A
-
+
U
A
T
D
ENTER  
O
JU  
S
S
T
T
A
T
U
S
O
N
/S  
P
O
T
W
A
N
E
D
R
B
Y
Indicators  
ADJUST  
IMAGE  
To turn on the projector:  
Only after you press the "ON/STAND BY" button on the projector cabinet or "POWER ON" button on the remote control will the power  
indicator turn to green and the projector become ready to use.  
NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. (See page E-48.)  
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.  
Lamp mode:  
High-Bright mode  
STATUS  
STATUS  
POWER  
Status of indicators: Stand by  
POWER  
OFF  
ON  
Steady light  
STATUS  
POWER  
STATUS  
Steady orange light  
POWER  
POWER  
Flashing green  
light  
Steady green  
light  
Lamp mode:  
Eco mode  
Steady green light  
Flashing for 3 minutes.  
During this time High-Bright  
mode is forcefully selected.  
E – 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To turn off the projector:  
First press the Power (ON/STANDBY) button on the projector cabinet or the POER OFF button on the remote  
control for a minimum of two seconds. The power indicator will glow orange. After the projector turns off, the  
cooling fans keep operating for ONE minute.  
NOTE: Do not disconnect the power cable during this time. Then, unplug the power cable. The power indicator will go out.  
Status of indicators: Off  
Fan running  
Stand by  
POWER  
OFF  
ON  
STATUS  
STATUS  
POWER  
POWER  
Flashing green  
light  
Steady orange  
light  
About Startup Screen  
(Menu Language Select screen)  
When you first turn on the projector, you will get the Startup screen.  
This screen gives you the opportunity to select one of the seven menu languages: English, German,  
French, Italian, Spanish,Swedish and Japanese.  
POWER  
OFF  
ON  
MENU  
To select a menu language, follow these steps:  
1. Use the Select ▲ or ▼ button to select one of the seven languages for the menu.  
ADDRESS  
BS  
-
+
ENTER  
MENU  
ADJUST  
PICTURE WHITE BAL.  
IMAGE  
-
+
ENTER  
PROJECTOR  
GHI  
ABC  
DEF  
1
JKL  
2
MNO  
3
PQR  
4
STU  
5
VWX  
6
YZ?  
9
8
7
,.  
UNDO CANCEL  
2. Press the Enter button to execute the selection.  
0
TEST  
INFO.  
HELP  
AUTO  
MENU  
POSITION PIXEL  
LENS  
-
+
ENTER  
MUTE  
SHUTTER  
PICTURE  
SOUND  
OSD  
KEYSTONE AMPLITUDE ENTRYLIST  
R
G
B
MAGNIFY  
+
+
3. The Basic/Custom menu will be displayed in the language you  
have selected.  
-
-
CANCEL  
FOCUS  
CTL  
ZOOM  
LENS  
To close the menu, press the Cancel button.  
After this has been done, you can proceed to the advanced menu operation.  
If you want, you can select the menu language later. See "Language" on page E-45.  
E – 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2) Press and hold the CTL and press the ZOOM + or - button to adjust the  
image size. You can also adjust the image size by using the ZOOM + or -  
button on the projector cabinet.  
Set up the projector  
1. Turn on the projector  
2. Select your type of projection:  
Desktop front, ceiling rear, desktop rear, and ceiling front.  
MAGNIFY  
+
+
-
FOCUS  
CTL  
ZOOM  
LENS  
3. Display the test pattern by pressing the TEST button on the re-  
mote control or using the menu.  
TEST  
4. Adjust the image position and the image size.  
(1) Press and hold the CTL button and press the POSITION button to display  
the Lens Shift adjustment screen.  
Use the Select button on the remote control or the LENS SHIFT button on  
the projector cabinet to move the image horizontally and vertically.  
To close the the Lens Shift adjustment screen, press the CANCEL button.  
See page E-13 for “Lens Shift Adjustable Range”.  
(3) Press and hold the CTL button and press the FOCUS + or - button to  
obtain the best focus. You can also adjust the focus by using the FOCUS  
+ or - button on the projector cabinet.  
POSITION  
LENS  
MAGNIFY  
+
+
-
FOCUS  
CTL  
ZOOM  
CTL  
LENS  
-
E – 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other adjustments  
Rotate the projector to make the  
image square.  
Rotate the four feet to make the  
image square to the screen.  
Each of the feet height can be changed up to 20 mm or at angles up to  
3.5 degrees.  
Use keystone correction for  
proper adjustment.  
P
C
C
O
N
T
R
O
L
O
U
T
R
E
M
O
TE  
1
,
L
L
/M  
O
O
R
N
N
G
O
B
/M  
M
O
N
IT  
O
R
R
O
U
T
1
R
G
B
2
R
/C  
r
V
G
H
ID  
/Y  
E
O
1
B
V
/C  
b
V
ID  
E
O
/H  
2
L
V
/M  
R
R
L
/M  
O
N
O
L
/M  
S
O
-
N
V
ID  
O
E
O
R
A
U
D
IO  
O
U
T
Down  
Up  
E – 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. CONNECTIONS  
When used in standalone operation  
Connecting Your VCR Or Laser Disc Player  
Use common RCA cables (not provided) to connect your VCR or laser disc player to your GT1150 Projector.To  
make these connections, simply:  
1. Turn off the power to your projector and VCR or laser disc player.  
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc  
player, connect the other end to the Video input on your projector. Use standard RCA audio patch cords to  
connect the audio from your VCR or laser disc player to your projector (if your VCR or laser disc player  
has this capability). Be careful to keep your right and left channel connections correct for stereo sound.  
3. Turn on the projector and the VCR or laser disc player.  
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output  
requirements.  
VCR or other video equipment  
TV tuner  
DVI  
L/MONO  
L/MONO  
RGB 2  
R
DVD player  
VCR  
R
MONITOR OUT  
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
VIDEO 1  
VIDEO 2  
H/HV  
L/MONO  
R
R
L/MONO  
R
L/MONO  
L/MONO  
R
-
S VIDEO  
AUDIO OUT  
Audio equipment  
E – 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Your DVD Player with Component Output  
Use the optional Component V cable to connect your DVD player with the component output to your GT1150  
Projector. To make these connections, simply:  
1. Turn off the power to your projector and DVD player.  
2. Use the optional Component V cable to connect your DVD player to the RGB 1 input or use a D-Sub 15 pin  
cable to the RGB 2 input of your GT1150 projector.  
3. Turn on the projector and the DVD player.  
DVI  
L/MONO  
L/MONO  
R
R
HD VCR  
MONITOR OUT  
RGB 2  
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
DVD player  
VIDEO 1  
VIDEO 2  
H/HV  
L/MONO  
R
R
L/MONO  
R
L/MONO  
L/MONO  
R
-
S VIDEO  
AUDIO OUT  
Audio equipment  
E – 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Your PC Or Macintosh Computer  
Connecting your PC or Macintosh computer to GT1150 Projector will enable you to project your computer's screen  
image for an impressive presentation.  
To connect to a PC or Macintosh :  
1. Turn off the power to your projector and computer.  
2. Use the supplied RGB signal cable to connect your PC or Macintosh computer to the projector.  
3. Turn on the projector and the computer.  
4. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the  
computer.  
DVI  
L/MONO  
L/MONO  
R
R
RGB signal cable  
(supplied)  
MONITOR OUT  
RGB 2  
RGB signal cable  
(supplied)  
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
VIDEO 1  
VIDEO 2  
H/HV  
L/MONO  
R
R
L/MONO  
R
L/MONO  
L/MONO  
R
-
S VIDEO  
AUDIO OUT  
Pin adapter for Macintosh  
(not supplied)  
For older Macintosh, use a commercially available pin  
adapter to connect to your Mac's video port.  
PC  
Macintosh  
NOTE: To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribu-  
tion amplifier if connecting a signal cable longer than the supplied one.  
E – 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting an External Monitor  
Connecting a PC with DVI output  
You can connect a separate, external monitor to your GT1150 projec-  
tor to simultaneously view on a monitor the RGB analog, DVI analog,  
or component image you're projecting. To do so:  
The DVI (digital) input accepts up to the XGA signal.  
NOTE: The Auto Adjust feature does not work for DVI digital signal. When DVI  
signal is selected and the image position is not corrected, adjust the horizontal  
and vertical position using the Position/Clock screen. See page E-43 for more  
details.  
1. Turn off the power to your projector, monitor and computer.  
2. Use a 15-pin cable to connect your monitor to the RGB MONI-  
TOR OUTPUT (Mini D-Sub 15 pin) connector on your projector.  
3. Turn on the projector, monitor and the computer.  
NOTE:  
* The MONITOR OUT connector outputs RGB signal during standby. When  
the projector goes into standby, the image on an external monitor disap-  
pears for a moment.  
* The DVI digital output signal from the MONITOR OUT connector is muted.  
To DVI digital or DVI analog  
DVI cable (not supplied)  
DVI  
L/MONO  
L/MONO  
RGB 2  
R
DVI  
L/MONO  
L/MONO  
R
R
R
MONITOR OUT  
MONITOR OUT  
RGB 2  
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
VIDEO 1  
VIDEO 2  
H/HV  
VIDEO 1  
VIDEO 2  
H/HV  
L/MONO  
R
R
L/MONO  
R
L/MONO  
R
R
L/MONO  
R
L/MONO  
L/MONO  
R
L/MONO  
L/MONO  
R
-
S VIDEO  
AUDIO OUT  
-
S VIDEO  
AUDIO OUT  
E – 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Single Workstation  
You can connect a workstation to your GT1150 projector. To do so:  
1. Turn off the power to your projector and workstation.  
2. Use a BNC x 5 cable to connect your workstation and the RGB 1 connectors on your projector.  
3. Turn on the projector and a workstation.  
BNC
ן
5 cable  
To RGBHV output  
To RGBHV output  
Signal distribution  
DVI  
L/MONO  
L/MONO  
RGB 2  
R
To RGBHV input  
R
MONITOR OUT  
RGB 1  
R/Cr  
G/Y  
B/Cb  
To analog RGB output  
VIDEO 1  
VIDEO 2  
H/HV  
V
L/MONO  
R
L/MON
R
L/MONO  
L/MONO  
R
To analog  
RGB input  
-
S VIDEO  
AUDIO OUT  
Workstation  
NOTE: All cables mentioned above are sold separately.  
Information for Reducing Radiation of Electromagnetic Waves  
To reduce unnecessary radiation of electromagnetic waves, use the supplied ferrite core,  
3. Fix the supplied band to the cable as a stopper.  
* Pull the end of the band to tighten it. Cut off the surplus of the band.  
Installation Instructions  
1. Open and attach the ferrite core to a sig-  
nal cable as close as possible to the end  
that goes to the projector.  
Band  
* Push the catch to open the ferrite core.  
2. Close the ferrite core tightly.  
NOTE: Be sure to use the ferrite core at the end of the signal cable.  
To a connected equipment  
To RGB2 input of GT1150  
E – 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When Used with One Switcher (ISS-6020/ISS-6020G)  
Up to 10 input signals can be accepted when the projector is connected to one Switcher. Using the projector with  
the Switcher allows easy adjustment and signal selection.  
MONITOR OUT  
RGB 2  
BNC
ן
5 coaxial cable  
RGB 1  
R/Cr  
G/Y  
B/Cb  
V
ISS-6020  
VCR  
VCR  
VIDEO 1  
VIDEO 2  
H/HV  
L/MONO  
R
R
L/MONO  
Personal computer  
L/MONO  
L/MONO  
R
To RGBHV output  
To slot  
To audio output  
To REMOTE1  
IN  
PC CONTROL  
OUT  
IN  
Personal computer  
REMOTE  
2
OUT  
REMOTE 1  
SC, TRIGGER  
To audio input  
Audio system  
Optional control cable 15p-15p  
(CTL-6010)  
• Select [Advanced Menu] → [Projector Options] → [Switcher Control] → [SW1 Level]. See page E-49 for the information in detail.  
• For more information on the Switcher, refer to the user’s manual accompanying the ISS-6020/ISS-6020G Switcher.  
• All cables mentioned above are sold separately.  
• The RGB2 terminal will not work with the Switcher Control function.  
To use the projector with the Switcher ISS-6020 in the Switcher Control mode,  
* When connecting with the VIDEO INPUT MODULE (6020-VID), set the VIDEO MODE select switch (S3001) to "8". The VIDEO MODE select  
switch is located on the VIDEO INPUT MODULE (6020-VID).  
NOTE: While in the Switcher Control mode, a video standard is selected at the projector.  
* If you set the VIDEO MODE select switch (S3001) to "8" with the QUAD DECODER installed in the Switcher ISS-6020, the image will not be  
displayed correctly.  
In that case, first remove the QUAD DECODER from the Switcher ISS-6020.  
For more details, contact your dealer.  
E – 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When Used with Two or More Switchers (100 Inputs)  
Up to 100 inputs can be accepted using the NEC ISS-6020 Switcher.  
How to make connections:  
1 Connect the REMOTE 1 terminal of the master Switcher to the REMOTE 1 of the projector using the  
optional control cable (15p-15p/CTL-6010).  
2 Next connect the REMOTE 2 terminal of the master Switcher to the REMOTE 1 terminal of the first slave  
Switcher using the same optional control cable as mentioned above. Third, connect the REMOTE 2 termi-  
nal of the first slave to the REMOTE 1 of the second slave, and the REMOTE 2 terminal of the second slave  
to the REMOTE 1 terminal of the third slave (— and the REMOTE 2 of the ninth slave to the REMOTE 1 of  
the tenth slave). Connect all the Switchers with optional control cables.  
• Select [Advanced Menu] → [Projector Options] → [Switcher Control] → [SW2 Level]. See page E-49 for the  
information in detail.  
• Refer to the user’s manual accompanying the Switcher.  
• Cables mentioned are not included with the projector.  
NOTE:  
•
Be sure to set all the slide switches (S8603) of the Switcher to RS-422 positions. Set the one on the last slave Switcher to  
the appropriate position to match the connected equipment such as a personal computer. (RS-422/RS-232C for PC control  
of projector)  
Set the DIP switch S8601 of the Switcher.  
•
To RS232C  
Personal  
Computer  
To REMOTE 1  
To REMOTE 1  
To REMOTE 2  
Slave 1  
Slave 2  
To Slot 1-10  
To Slot 1-10  
To REMOTE 1  
To REMOTE 2  
To REMOTE 2  
To Slot 1  
To REMOTE 1  
To Slot 2  
To REMOTE 1  
To REMOTE 2  
To REMOTE 1  
To Slot 10  
Slave 10  
To Slot 1-10  
NOTE: The optional remote control RC-6320 for ISS-6020 will not work correctly in the SW Level 1 or 2 mode.  
To use the projector with the Switcher ISS-6020 in the Switcher Control mode,  
* When connecting with the VIDEO INPUT MODULE (6020-VID), set the VIDEO MODE select switch (S3001) to "8". The VIDEO MODE select  
switch is located on the VIDEO INPUT MODULE (6020-VID).  
NOTE: While in the Switcher Control mode, a video standard is selected at the projector.  
* If you set the VIDEO MODE select switch (S3001) to "8" with the QUAD DECODER installed in the Switcher ISS-6020, the image will not be  
displayed correctly.  
In that case, first remove the QUAD DECODER from the Switcher ISS-6020.  
For more details, contact your dealer.  
E – 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Set the DIP switch (S8601) of the Switcher as follows:  
NOTE: Slave numbers 1 to 10 must correspond to the master’s slot numbers 1 to 10.  
ISS-6020  
ISS-6020G  
Setting of S8601  
Output to  
OPEN  
Master  
The Projector  
1
1
1
2
2
2
3
4
5
6
6
6
7
7
7
8
8
8
SHORT  
OPEN  
Slave 1  
Slave 2  
Slave 3  
Slave 4  
Slave 5  
Slave 6  
Slave 7  
Slave 8  
Slave 9  
Slave 10  
Slot 1 of the Master  
Slot 2 of the Master  
Slot 3 of the Master  
Slot 4 of the Master  
Slot 5 of the Master  
Slot 6 of the Master  
Slot 7 of the Master  
Slot 8 of the Master  
Slot 9 of the Master  
Slot 10 of the Master  
3
4
5
SHORT  
OPEN  
3
4
5
SHORT  
OPEN  
1
2
3
4
5
6
7
8
SHORT  
OPEN  
1
1
2
2
3
4
5
6
6
7
7
8
8
SHORT  
OPEN  
3
4
5
SHORT  
OPEN  
1
1
1
2
2
2
3
4
5
6
6
6
7
7
7
8
8
8
SHORT  
OPEN  
3
4
5
SHORT  
OPEN  
3
4
5
SHORT  
OPEN  
1
1
2
2
3
4
5
6
6
7
7
8
8
SHORT  
OPEN  
3
4
5
SHORT  
E – 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOTE 1 Connector  
5
4
3
2
1
10  
9
8
7
6
15 14 13 12 11  
This connector is used for either connecting the ISS-6020/ISS-6020G Switcher or a third  
party external control device.When the Switcher is used, connect it with the optional control  
cable (15-15 pin; 50 ft./16m; CTL-6010) to this connector.  
When used with the Switcher.  
Pin No.  
1, 2, 6 and 7  
9
FUNCTION  
Sending and receiving data when the Switcher is used.  
Identifying the Projector  
15  
Ground  
8,11 and 12  
Used inside the Projector. Normally set to OPEN.  
When using with the Switcher ISS-6020/ISS-6020G, connect No. 1,2,6,7,9 and15 pins of  
the projector to the same No. pins of the switcher as shown below.  
Pin Configuration of Optional CTL-6010 Cable  
REMOTE 1 connector of  
the Projector mini D-sub  
15 pin (female)  
REMOTE 1 connector  
of the Switcher mini D-  
sub 15 pin (female)  
Shield (frame ground)  
6
1
6
1
7
2
7
2
9
9
15  
15  
Pins without a number are open.  
E – 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When used in stand alone operation.  
Pin No.  
FUNCTION  
SHORT/OPEN  
14  
External control mode ON  
External control mode OFF  
SHORT  
OPEN  
5
POWER ON  
POWER OFF  
SHORT  
OPEN  
10  
3
PICTURE MUTE ON  
PICTURE MUTE OFF  
SHORT  
OPEN  
MUTE SOUND ON  
MUTE SOUND OFF  
SHORT  
OPEN  
12pin  
OPEN  
8pin  
OPEN  
4pin  
11pin  
OPEN  
4,8,12,11  
OPEN  
RGB 1  
OPEN  
OPEN  
VIDEO 1  
SHORT  
OPEN  
OPEN  
OPEN  
SHORT  
OPEN  
S-VIDEO  
OPEN  
SHORT  
SHORT  
SHORT  
OPEN  
RGB 2  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
VIDEO 2  
OPEN  
SHORT  
OPEN  
RGB1 (S-VIDEO)  
DVI (DIGITAL)  
PC CARD VIEWER  
DVI (ANALOG)  
RGB 1 (VIDEO)  
RGB 2 (S-VIDEO)  
RGB 2 (VIDEO)  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
OPEN  
SHORT  
SHORT  
OPEN  
SHORT  
* When the combinations other than specified in the above table are selected, the input will be forcefully  
switched to RGB 1.  
* The term “SHORT” means to connect with pin 15  
* When in the external control mode, the POWER, Source/Alphanumeric, PICTURE MUTE and SOUND MUTE  
buttons on the remote control will not function.  
* When the External control mode is set to ON, the following settings are not effective:Timer, Auto Start, Power  
Management, Power Confirmation, Default Source Select.  
NOTE: Pin 13 is the external remote signal terminal. The projector can be controlled by the same format signal as the  
supplied remote control from the external controller regardless of setting on Pin 14.  
NOTE: When turning off the power to the projector using the external control, do not disconnect the plug from the power  
outlet. These procedures are to protect your projector and the connected equipment.  
E – 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Multiple Projector with Remote Control  
You can operate multiple projectors with the same remote control in wireless operation.  
To do so:  
1. Select [Advanced Menu]→[Projector Options]→[Setup]→[Page 6]→[Projector ID] and assign an ID number to  
each projector. See also page E-49.  
2. On the remote control specify the ID number of the projector to be adjusted. Press and hold the CTL and press  
MENU (ADDRESS) button to enter the ID number.  
You can operate the projector assigned the same ID number as the remote control.  
Projector ID= 01  
Projector ID= 02  
Projector ID= 03  
Remote Address = 03  
You can daisy-chain multiple projectors and operate them separately with the same remote control in wired operation.  
To do so:  
1) Use the remote control cable to connect the REMOTE 2 Output of one projector to the REMOTE 2 Input of the next  
projector until all the projectors are connected. Only one remote control cable is supplied with each projector.  
2) Specify a unique projector ID for each projector.  
3) Specify the same remote address as the projector ID to be adjusted.  
NOTE: Specifying "None" for projector ID allows you to operate multiple projectors concurrently. However, some projectors may not  
synchronize to the other projectors.  
IN  
PC CONTROL  
OUT  
IN  
To REMOTE 2 IN  
To REMOTE 2 IN  
REMOTE  
2
OT  
Projector ID= 01  
Projector ID= 02  
Projector ID= 03  
From REMOTE 2 OUT  
Remote Address = 03  
E – 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the PC CONTROL connectors  
The Link mode function allows you to adjust or set multiple projectors using the RGB 2 and the PC CONTROL  
connectors.  
Connection for Double Stacking in Link Mode  
Connect source equipment to the master projector.  
IN  
L/MONO  
R
Master projector  
PC CONTROL  
MONITOR OUT  
RGB 2  
OUT  
RGB signal cable  
(supplied)  
Bi-directional RS-232C  
cable (not supplied)  
IN  
PC CONTROL  
OUT  
LMO
RGB 2  
R
MONITOR OUT  
Slave projector  
It is recommended that you use a commercially available distribution  
amplifier if connecting multiple projectors in Link mode.  
E – 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. OPERATION  
This section describes how to select a computer or video source, ad-  
just the picture and sound, edit a signal and adjust all other settings  
and adjustments for proper projector set-up.  
Using the Menus  
NOTE: The on-screen menu may not be displayed correctly while interlaced  
motion video image is projected.  
General Controls  
Before you turn on the projector ensure that the computer or video  
source is turned on and that the lens hood cap is removed.  
1. Press the "Menu" button on the remote control or projector cabi-  
net to display the menu.  
2. Press the ▲▼ buttons on the remote control or the projector cabi-  
1. Turn on the Projector  
net to highlight the menu for the item you want to adjust or set.  
Plug the supplied power cable in the wall outlet. The projector  
will go into its standby mode and the power indicator will glow  
orange.  
Only after you press the "POWER ON" button on the remote con-  
trol ("ON/ STAND BY" button on the projector cabinet) will the  
power indicator turn to green and the projector become ready to  
use.  
ᮣ
3. Press the button or the "Enter" button on the projector cabinet  
or the remote control to select a submenu or item.  
NOTE: The right-oriented delta symbol indicates further choices are avail-  
able.  
4. Adjust the level or turn the selected item on or off by using "Se-  
NOTE: To turn the projector on by plugging in the power cable, use the  
menu and enable the "Auto Start" feature. (See page E-48.)  
ᮤ
ᮣ
lect" or buttons on the remote control or the cabinet. The on-  
screen slide bar will show you the amount of increase or decrease.  
2. Select The Computer Or Video Source  
5. Changes are stored until you adjust it again.  
Press one of the Source buttons on the remote control to select the  
desired source. Or press the MENU button on the remote control  
and use the Source Select to select your video source: Video, S-  
Video, RGB, PC Card Viewer, DVI Digital or DVI Analog.  
ENTER ......... Stores the setting or adjustments.  
CANCEL ....... Return to the previous screen without storing settings or  
adjustments.  
3. Adjust The Image  
NOTE: The change is stored automatically when any one of the following pro-  
cedures is performed:  
* The on-screen dissapears.  
Press the ADJUST PICTURE button on the remote control or use  
the menu to adjust the picture.  
* The projector goes into standby.  
* One input is switched to another.  
4. Turn Off The Projector  
First press the "POWER OFF" button on the remote control ("ON/  
STAND BY" button on the projector cabinet) for a minimum of  
two seconds. The power indicator will glow orange. Then, unplug  
the power cable. The power indicator will go out.  
6. Repeat steps 2-5 to adjust an additional item, or press "Cancel"  
on the projector cabinet or the remote control to quit the menu  
display.  
IMPORTANT:  
Using the Magnifying Glass Icon  
• The projector should be unplugged if it will not be used for an extended  
period.  
When the image is magnified with the MAGNIFY button on the remote  
ᮤ
ᮣ
control, pressing CTL and any one of  
magnifying glass icon.  
,
, ▲ or ▼ will display the  
• If you want to turn off the image briefly (five minutes or less), press the  
MUTE PICTURE button instead of turning the projector off and on.  
• The projector will display a black, blue image or logo if no input signal is  
present.  
• Do not turn the projector off and then immediately back on. The Projector  
needs to cool down for ONE minute before it is powered on again.  
At this time you can select any part of the screen and expand it.  
ᮤ
ᮣ
To move the magnifying glass icon, use  
,
, ▲ or ▼.  
ᮤ
ᮣ
Press CTL and any one of  
icon will disappear.  
,
, ▲ or ▼ again and the manifying glass  
CAUTION: Do not connect the power cable while the cooling fan is running.  
E – 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ᮤ
ᮣ
3. In order for the changes to take effect, use the or button on  
the remote control or the projector cabinet to highlight “OK”,  
then press the Enter button. To cancel the changes, use the ▲ or  
▼ buttons to highlight “Cancel” and press the “Enter” button.  
To return to the factory default, select “Reset” then press the “En-  
ter” button.  
Customizing Basic/Custom Menu  
The Basic/Custom menu can be customized to meet your requirements.  
Selecting a menu item from the “Basic/Custom Menu Edit” list, allows  
you to custom tailor the menu items to your needs.  
1. Select “Basic/Custom Menu Edit” to display the “Basic/Custom  
Menu Edit” screen.  
The default Basic/Custom Menu items are:  
Source Select (RGB1/2, Video1/2, S-Video, DVI digital/analog, and  
PC CardViewer), Picture, Volume, Image Options (Keystone, Color  
Temperature and Lamp Mode), Projector Options (Menu and Setup),  
Tools (Capture and PC Card Files) and Help (Contents and Infor-  
mation)  
NOTE: Once you have selected OK on the Basic/Custom Menu Edit screen, you  
cannot cancel the changes on the Menu screen. However, you can re-edit the  
menu items over again as described in the steps above.  
NOTE: If the “Advanced Menu” item has been selected on the Menu mode, you  
get the “Confirmation Change Menu” upon completion of “Basic/Custom Menu”  
editing. In this case, selecting “Yes” then “Enter” will close all the menus and  
apply the changes from the Advanced menu to the Basic/Custom Menu. If you  
select “No” then “Enter” functions, then all menu items will return to the Ad-  
vanced menu, but your changes will still be available within the “Basic/Custom  
Menu” selection. To display the previously tailored Basic/Custom Menu, select  
“Basic/Custom Menu” from the “Menu Mode”.  
2. Use the ▲ or ▼ button to highlight your selection and press the  
Enter button to place a check mark next to an option. This action  
enables that feature.  
Press the Enter button again to clear the check box.  
An item “To Advanced Menu” will be added to the bottom of the Basic/  
Custom Menu.  
Selecting this item and pressing the “Enter” button will display the “Ad-  
vanced Menu” features.  
ᮣ
If you select an item with a solid triangle and press the Enter  
button on the remote control or the projector cabinet, you can  
enable all the items within that submenu.  
Also you can turn on an item within the submenu without placing  
a check mark on the main menu item.  
NOTE: Up to 12 main menu items (within Basic/Custom Menu Edit, not  
including submenu items) can be selected.  
E – 36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Direct Button Combinations  
CTL+ SOURCE (1-10)  
Switches to any selected signal found in the Entry List.  
To enable this combination, you must first assign specific remote buttons for direct input  
selection in the Entry Edit window.  
CTL+ ENTER (While displaying Entry list)  
CTL+CANCEL  
Displays the Entry Edit Command window.  
Returns to the previous menu without closing the slidebar or dialog.  
Clears all menus or adjustment/setting screens.All adjustments are saved automatically.  
CTL+ UNDO  
ᮤ
ᮣ
CTL+  
/
/ ▲ / ▼  
Moves the slidebar or dialog box horizontally or vertically.  
Displays the magnifying glass icon.  
While using zoom on remote control:  
ᮤ
CTL+ (BS)  
Deletes one letter or numeral in the entry screen.  
Turns off the on-screen display forcefully.  
CTL+MUTE OSD  
SOURCE (1-10) in SW Level mode  
Displays the Select switcher Input Slot window.  
NOTE: This feature is available for SW 2 Level mode only.  
When the SW 1 Level mode is selected, pressing Source button switches to the corresponding  
slot without displaying the Select Slot window.  
CTL+ MENU (ADDRESS)  
CTL+ IMAGE (PROJECTOR)  
CTL+ POSITION (LENS)  
CTL+ KEYSTONE (R)  
CTL+ AMPLITUDE (G)  
CTL+ ENTRY LIST (B)  
Displays the remote ID entry window.  
Sequentially selects the Projector Options sub menu.  
Displays the Lens Shift adjustment window.  
Turns on red. Available only when the projector is in the test pattern mode.  
Turns on green. Available only when the projector is in the test pattern mode.  
Turns on blue. Available only when the projector is in the test pattern mode.  
Pressing and holding down CTL and then ENTRY LIST buttons simultaneously, enters a  
signal in the Entry List when you are not displaying a test pattern.  
CTL+ MAGNIFY (ZOOM)  
CTL+ (FOCUS)  
Zooms the lens in and out  
Adjusts the lens focus.  
E – 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu tree  
When Switcher Control is turned on:  
Switcher  
Entry List  
Advanced Menu  
Source Select  
Picture  
1.RGB1  
2.RGB2  
Volume  
3.Video1  
Image Options  
Projector Options  
Tools  
Help  
Test Pattern  
4.Video2  
5.S-Video  
6.DVI (DIGITAL)  
7.DVI (ANALOG)  
8.PC Card Viewer  
more  
9.RGB1 (Video)  
0.RGB1 (S-Video)  
RGB2 (S-Video)  
RGB2 (Video)  
Entry List  
Brightness / Contrast / Color / Hue / Sharpness  
Volume  
High-Bright/Eco  
Keystone  
Color Temperature  
Lamp Mode  
Normal / Natural 1 / Natural 2  
Gamma Correct  
Advanced Options  
Factory Default  
Aspect Ratio  
Noise Reduction  
Color Matrix  
1.33:1 / 1.78:1 / 1.85:1 / 2.05:1 / 2.35:1  
Off / Low / Medium / High  
Select Color Matrix HDTV/SDTV  
Select Color Matrix Type B-Y/R-Y,Cb/Cr,Pb/Pr  
Brightness R/G/B, Contrast R/G/B  
Red / Green / Blue  
White Balance  
Switcher Gain  
Position/Clock  
Resolution  
Horizontal / Vertical / Clock / Phase  
Auto / Native  
Video Filter  
On / Off  
Overscan  
Clamp Timing  
Y/C Delay  
0% / 5% / 10% / 25%  
Auto / Tri-Sync / Front Porch  
(-8 – +8)  
YTR Adjustment  
CTR Adjustment  
HD Delay  
Gain (0–7)  
Gain (0–7)  
On / Off  
All Data / Current Signal  
On/Off Timer  
Sleep Timer  
Execute Switch (Active / Inactive), Edit  
Preset Time (Off / 0:30 / 1:00 / 1:30 / 2:00)  
Timer  
Menu  
Setup  
Page1  
Menu Mode (Basic / Custom Menu, Advanced Menu, Service Menu)  
Basic/Custom Menu Edit  
Language (English / German / French / Italian / Spanish / Swedish / Japanese)  
Menu Display Time (Manual / Auto 5 sec / Auto 10 sec / Auto 30 sec)  
Link Mode  
Switcher Control  
LAN Mode (option)  
Page2  
Display Select  
Date (On / Off)  
Time (On/Off)  
Input Terminal (On / Off)  
Projector ID (On / Off)  
Source Name (On / Off)  
Date Format  
(MM/DD/YYYY, MM/DD/YYYY ddd, DD/MM/YYYY, DD/MM/YYYY ddd,  
YYYY/MM/DD, YYYY/MM/DD ddd, Month DD,YYYY, Month DD,YYYY ddd)  
Data, Time Preset  
Page3  
Page 1  
Projector Pointer (Pointer 1 – 8)  
Direct Button Volume Bar (On / Off)  
Keystone Bar (On / Off)  
Orientation (Desktop Front / Ceiling Rear / Desktop Rear / Ceiling Front)  
Background (Blue / Black / Logo)  
PC Card Viewer Options Show Folder List (Auto Play / Manual Play)  
Interval (5-300 sec)  
Capture Options (High Quality / Normal / High Compression)  
Page 2  
Signal Select  
RGB1 (Auto / RGB / Component)  
RGB2 (Auto / RGB / Component)  
Video1 (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
Video2 (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
S-Video (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
RGB1 (Video) (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
RGB1 (S-Video) (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
RGB2 (Video) (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
RGB2 (S-Video) (Auto / NTSC3.58 / NTSC4.43 / PAL / PAL60 / SECAM)  
Page 3  
Page 4  
Signal Select  
Auto Adjust [RGB Only] (On / Off)  
Power Management (On / Off)  
Keystone Save (On / Off)  
Auto Start (On / Off)  
Power Off Confirmation (On / Off)  
Fan High Speed Mode (On / Off)  
Clear Lamp Hour Meter  
Built-in Speaker  
Clear Filter Usage  
Page 5  
Page 6  
Remote Sensor (Front / Back / Left / Right)  
S-Video Mode Select (Off / S2)  
Communication Speed (4800 / 9600 / 19200 / 38400)  
Projector ID (Enable / Disable) 1-64  
Default Source Select (Last / Suto / Select)  
(RGB1 / RGB2 / Video1 / Video2 / S-Video / DVI [DIGITAL] / DVI [ANALOG] / PC Card Viewer/  
RGB1 [Video] / RGB1 [S-Video] / RGB2 [Video] / RGB2 [S-Video] )  
[SW 1 Level] (Slot1–10)  
[SW 2 Level] (M-01 S-01 – M-10 S-10)  
Capture  
PC Card Files  
Standalone/Master/Slabe  
Standalone / SW 1 Level / SW 2 Level  
Network Board / Default Gateway  
Contens  
Contens  
Information  
Page 1  
Page 2  
Page 3  
Page 4  
Page 5  
Page 6  
Source Name / Input Terminal / Entry No. /Horizontal Frequency / Vertical Frequency / Sync Polarity  
Signal Type / Video Type / Sync Type / Interlace / Resolution / Direct Key  
Aspect Ratio / Gamma Correction / Noise Reduction / Color Matrix/Matrix Type  
Lamp Remaining Time / Lamp Hour Meter / Filter Usage / Projector Usage / Projector ID  
Version (BIOS / Firmware / Data / SUB-CPU)  
Cross Hatch, Gray Bars, Color Bars,  
Black Raster,Gray Raster, White Raster,  
ANSI Checker, Focus, Aspect Ratios  
Red/Green/Blue  
Link Mode (Master / Slave)  
E – 38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Elements  
Tab  
Help Button  
Title bar  
Highlight  
Radio button  
OK Button  
Cancel Button  
Solid triangle  
Check box  
Slide bar  
Tool bar  
Menu windows or dialog boxes typically have the following elements:  
Title bar:  
Indicates the menu title.  
Highlight:  
Indicates the selected menu or item.  
Solid triangle: Indicates further choices are available. A highlighted triangle indicates the item is active.  
Tab: Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.  
Radio button: Use this round button to select an option in a dialog box.  
Check box:  
Slide bar:  
OK button:  
Place a checkmark in the square box to turn the option On.  
Indicates settings or the direction of adjustment.  
Press to confirm your setting.You will return to the previous menu.  
Cancel button: Press to cancel your setting.You will return to the previous menu.  
Help button:  
Toolbar:  
Press the Help button on the remote control to display help.  
Contains several icons for specific tasks. It is also referred to as "launcher".  
E – 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When using with two or more Switcher ISS-6020:  
Menu Descriptions & Functions  
Source Select  
Use the Select ▲ or ▼ button to select the master slot number from 1  
to 10 and then the slave slot number from 1 to 10 on the Select Slot  
menu. Select OK and press ENTER.  
To close the window without storing the settings, select Cancel and  
press ENTER.  
Entry List  
Displays the list of the entry signals. Use the ▲▼ buttons on your re-  
mote control or the projector cabinet to select the signal and press the  
ENTER button on the remote control or the projector cabinet to project  
the image of the selected source.  
When Switcher Control is set to "Standalone", you can select a video  
source such as a VCR, DVD player, laser disc player, computer, or  
document camera depending on what is connected to your inputs, or  
PC Card Viewer (PC card installed).  
Enables you to select a video source such as aVCR, DVD player, laser  
disc player, computer or document camera depending on what is con-  
nected to your inputs.  
Press the up/down buttons on your remote control or the projector cabi-  
net to highlight the menu for the item you want to project.  
* RGB1,2  
* Video 1,2  
* S-Video  
* RGB Digital  
* RGB Analog  
* PC Card Viewer  
* RGB1 (VIDEO)  
* RGB1 (S-VIDEO)  
* RGB2 (S-VIDEO)  
* RGB2 (VIDEO)  
Entry Edit Command (Expert mode only)  
You can edit the signal on the entry list.  
To do so:  
1. While pressing and holding CTL, press ENTER on the remote control to  
display the Entry Edit Command window.  
Switcher  
You can select the slot number from 1 to 10 of the Switcher(s) ISS-  
6020.  
* Cut Enables you to remove a selected signal from the list and place  
it on the “clipboard” in the projector.  
* Copy Enables you to copy a selected signal from the list and place  
it on the “clipboard” in the projector.  
When using with a single Switcher ISS-6020:  
* Paste Enables you to paste the signal placed on the “clip-board” to  
any other line of the list.To do this, select “Paste” and then select the  
line number you want to paste to. Last press ENTER.  
* Edit Enables you to change source name or assign the direct key.  
* The following buttons are not available for the currently projecting  
signals:  
1) The Cut and Paste buttons on the Entry Edit Command screen  
2) The Input Terminal button on the Entry Edit screen  
Use the Select ▲ or ▼ button to select the desired slot number from 1  
to 10 of the ISS-6020 Swicher and press ENTER.  
When complete, select OK and press ENTER. To exit without storing  
setting, select Cancel.  
E – 40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Select “Source Name” and press ENTER to display the Source Name  
Edit window.You can change source name on this window.  
Select "Input Terminal" and press ENTER to display the Input Terminal  
window.You can change input terminal on this window.  
Prev  
Play Jump Setup  
View  
Next  
Stop Select  
Delete  
A press of the MENU button displays the toolbar; a press of the MENU  
button again displays the Menu and hereafter each press of the MENU  
button switches displaying between the Menu and the toolbar.  
The launcher is a tool bar including the following buttons:  
Select “Direct Key” and press ENTER to display the Direct Key win-  
dow.You can assign specific remote keys for direct signal input selec-  
tion.  
Prev ............. Returns to the previous slide or folder.  
Next ............. Advances to the next slide or folder.  
Play .............. Plays back automatically or manually depending on the set-  
ting on PC Card Viewer Options of the menu. This allows you  
to move on to the next slide when "Manual Play" is selected.  
Stop ............. Stops Auto Play while you are playing back and to resume  
playing from the selected slide or folder when "Auto Play" is  
selected.  
NOTE: Existing direct key settings are overwritten with new settings.  
Jump ........... Displays a list of slides while you are playing back.  
Select ........... Displays a list of folders while you are playing back.  
Setup ........... Displays the PC Card Viewer Options dialog box on Page 1 of  
the Setup dialog box.  
Delete........... Deletes a captured slide(s) or all the captured slides in the  
selected folder.  
Select “List” and press ENTER to display the direct Key assignment  
list.  
Select “OK” and press ENTER to close the window.  
To close the List window, press CANCEL on the remote.  
View ............. Hides the tool bar while you are playing back. Pressing the  
MENU button shows it again.  
Picture (not available for PC Card Viewer)  
PC Card Viewer  
This feature enables you to make presentations using a PC card that contains  
captured images and slides created with the exclusive PC Card Viewer Utility  
contained in the CD-ROM. See page E-53 for installing the PC Card Viewer  
Utility. The starting screen for the PC Card Viewer varies depending on the  
settings of the Setup's Page 1. See Setup on page E-47.  
Provides access to controls for your image. Use ▲▼ buttons on the  
projector cabinet or the remote control to highlight the menu for the  
item you want to adjust.  
NOTE: Even if you switch the current PC Card Viewer source to another source,  
the current slide is retained. When you return back to the PC Card Viewer, you  
will get the slide that has been retained. A launcher will appear when you press  
the MENU button.  
Brightness ... Adjusts the brightness level or the back raster intensity.  
Contrast ....... Adjusts the intensity of the image according to the incoming  
signal.  
Color ............ Increases or decreases the color saturation level (not valid  
for RGB).  
Hue .............. Varies the color level from +/- green to +/-blue. The red level  
is used as reference. This adjustment is only valid for Video  
and Component inputs (not valid for RGB).  
Sharpness .... Controls the detail of the image for Video (Not valid for RGB  
and Component).  
Volume (not available for PC Card Viewer)  
Adjusts the sound level of the projector.  
NOTE: You can also display the volume bar without opening the menu. See  
"Volume Bar (Direct Button)"on page E-46 for more details.  
E – 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Gamma Correction  
Image Options  
ᮤ
ᮣ
Use the or button to choose "Normal" when in a lighted room and  
"Natural 1&2" when in a darkened room. "Natural 1" for better flesh  
tone; "Natural 2" for true reproduction of middle tones.  
Each mode is recommended for :  
Normal ......... For the regular picture  
Natural 1 ...... For true color reproduction of natural tones  
Natural 2 ...... For dark portions of a picture  
Keystone  
Aspect Ratio (not available for RGB, DVI digital and PC Card Viewer)  
This feature corrects the keystone (trapezoidal) distortion to make  
the top of the screen longer or shorter to be the same as the bottom.  
ᮤ
ᮣ
Use the or buttons on the slide bar to correct the keystone  
(trapezoidal) distortion.  
Keystone distortion  
Normal  
NOTE:  
1) The maximum keystone angle that can be corrected is 30 degrees upward  
and 30 degrees downward with the projector placed horizontally on the ground  
plane.  
2) When "Resolution" is set to "Native", this feature is not available, and the  
stored settings and adjustments are invalid.  
Depending on the type of graphics being used, the picture may get  
blurred or keystone correction may not be possible when excessive  
keystone correction is used.  
The idea is, the closer you are to native resolution, the better image  
you will see.  
Color Temperature  
This feature adjusts the color temperature using the slide bar.  
Move the slide bar to the right to increase the color temperature for a  
bluish image; to the left to decrease it for a reddish image.  
You can select the aspect ratio for input signal and display area re-  
spectively.  
ᮤ
ᮣ
Select the appropriate aspect ratio using the Select  
button.  
,
, ▲, or ▼  
Lamp Mode  
NOTE: When "Resolution" is set to "Native", this feature is not available, and the  
stored settings and adjustments are invalid.  
Noise Reduction (not available for RGB and PC Card Viewer)  
This feature enables you to select two brightness mode of the lamp:  
High-Bright and Eco modes.The lamp life can be extended up to 2000  
hours by using the Eco mode.  
High-Bright Mode .......This is the default setting.  
You can select three levels video noise reduction.  
Eco Mode ....................Select this mode to increase the lamp life.  
NOTE: The lower the Noise Reduction level, the better the image quality by way  
of higher video bandwidth.  
NOTE: If you have selected the Eco mode, the lamp lights in High-Bright mode  
for 3 minutes after the projector is turned on. After 3 minutes the lamp will  
change to Eco mode.  
E – 42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Matrix (available for component video signal only)  
Position/ Clock (when Auto Adjust is off)  
First select an appropriate color matrix to fit your component signal for  
HDTV or SDTV. Then select an appropriate matrix type from B-Y/R-Y,  
Cb/Cr or Pb/Pr.  
This allows you to manually adjust the image horizontally and verti-  
cally, and adjust Clock and Phase.  
White Balance (not available for PC Card Viewer)  
Horizontal/Vertical Position  
.................... Adjusts the image location horizontally and vertically using  
ᮤ
ᮣ
the and buttons.  
This adjustment is made automatically when the Auto Adjust  
is turned on. See "Auto Adjust (RGB Only) on page E-48 for  
turning on or off the Auto Adjust feature.  
Clock .......... Use this item to fine tune the computer image or to remove  
any vertical banding that might appear. This function adjusts  
the clock frequencies that eliminate the horizontal banding in  
the image.  
ᮤ
ᮣ
Press the and buttons until the banding disappears.  
This adjustment may be necessary when you connect your  
computer for the first time. This adjustment is made auto-  
matically when the Auto Adjust is turned on.  
Phase ........... Use this item to adjust the clock phase or to reduce video  
noise, dot interference or cross talk. (This is evident when  
This allows you to adjust the white balance. Brightness for each color  
(RGB)is used to adjust the black level of the screen;  
ᮤ
part of your image appears to be shimmering.) Use the  
Contrast for each color (RGB)to adjust the white level of the screen.  
First use the ▲ or ▼ buttons to select R, G, or B for the brightness and  
ᮣ
and buttons to adjust the image. Use "Phase" only after the  
ᮤ
ᮣ
"Clock" is complete. This adjustment is made automatically  
when the Auto Adjust is turned on.  
the contrast. Next use the or buttons to adjust the level.  
Switcher Gain (available only when used with ISS-6020)  
Resolution (when Auto Adjust is off)  
This allows you to activate or deactivate the Advanced AccuBlend fea-  
ture.  
Auto ............. Turns on the Advanced AccuBlend feature. The projector au-  
tomatically reduces or enlarges the current image to fit the  
full screen.  
Native........... Turns off the Advanced AccuBlend feature. The projector dis-  
plays the current image in its true resolution. See “Auto Ad-  
just (RGB Only)” on page E-48 for turning on or off the Auto  
Adjust feature.  
This feature adjusts the input level of the signal. This must be done to  
each color:R, G, and B.  
NOTE: While you are displaying an image with higher resolution than the  
projector's native resolution, even when you are in the Native mode, the image  
is displayed full screen using the Advanced AccuBlend feature.  
E – 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Filter (when Auto Adjust is off)  
Factory Default  
This function reduces video noise.  
Select On/Off with the Select or button.  
ᮤ
ᮣ
On ................ The low-pass filter is applied.  
Off ................ The filter is removed.  
Changes all adjustments and setting to the factory preset for each  
source individually except Lamp Hour Meter, Projector Usage, Lan-  
guage and Communication Speed. (To reset the lamp usage time, see  
"Clear Lamp Hour Meter" on page E-48.)  
Screen adjustments are possible even when the filter is On.  
Overscan (RGB only)  
All Data ............... Reset all the settings for all the signals to the factory  
preset.  
Current Signal ..... Resets the adjustments for the current signal to the fac-  
tory preset levels.  
You can select overscan percentage for RGB signal.  
Select the appropriate option using the Select or button.  
ᮤ
ᮣ
NOTE: When "Resolution" is set to "Native", this feature is not available, and the  
stored settings and adjustments are invalid.  
The items that can be reset for the currently projected image are:  
Picture (Brightness, Contrast, Color, Hue and Sharpness) and Image  
Options (Color Temperature, Gamma Correction, Advanced Options  
[Aspect Ratio, Noise Reduction, Color Matrix, White Balance, Switcher  
Gain, Position/Clock, Resolution, Video Filter, Overscan, Clamp Tim-  
ing, Y/C Delay, YTR Adjustment, CTR Adjustment and HD Delay] ).  
Clamp Timing (not available for DVI digital)  
NOTE: The Volume, Keystone, Lamp Mode and all the items in the Projector  
Options can be reset only when "All Data" is selected.  
This function sets the standard black level position of the displayed  
image. Select one of the following three options.  
Auto ............. Normal setting.  
Tri-Sync ....... Setting for HDTV signal  
Front Porch .. For other settings than above  
Projector Options  
Enables you to set preferences and other operating options.  
Timer  
Y/C Delay (not available for RGB and DVI digital)  
Enables you to turn on or off your projector automatically at a specified  
time.Two timer functions are available: On/Off Timer and Sleep Timer.  
Adjusts Y/C delay level ( -8 and +8).  
YTR Adjustmen (not available for RGB and DVI digital)  
[On/Off Timer]  
Adjusts luminance transient time (0-7).  
CTR Adjustment (not available for RGB and DVI digital)  
Adjusts chroma transient time (0-7).  
HD Delay (available for DVI digital signal only)  
Up to eight settings can be programmed.  
• Before setting On/Off Timer, make sure that Date, Time Preset fea-  
ture is set.  
• Even after setting On/Off Timer, turning the projector on or off with  
the remote control is possible.  
• There are two time display formats: 24-hour or AM/PM for-mat.  
This feature is used to correct vertical jitter of DVI digital signal.  
Select On/Off with the Select or button.  
ᮤ
ᮣ
On ................ Delays the horizontal sync.  
Off ................ Does not delay the horizontal sync.  
E – 44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Open the On/OFF Timer window.  
Menu  
[Page 1]  
2. Select EDIT and press ENTER on the remote control to open the  
EDIT window.  
3. Set the Week, Day, On-Time and Off-Time using the Select buttons  
and Source buttons (1 thru 10). To cancel the on-time or off time,  
use Delete.  
Allows you to set preferences for the on-screen menu.  
Press "OK" to save your changes for all the features.  
Menu Mode:  
4. Select Set and press the ENTER button on the remote control to  
complete the setting. To close, select Close.  
This feature allows you to select two menu modes: Advanced Menu  
and Basic/Custom Menu.  
5. To enable your setting, select Active on the Execute Switch.  
Advanced Menu .......... This is the menu that contains all the available menus  
and commands.  
Basic/Custom Menu .... This is the menu that you can customize using the  
6. Select OK and press the ENTER button on the remote control to  
complete the setting.  
Basic/Custom Menu Edit to fit your needs.  
The factory default Basic/Custom menu includes:  
NOTE: When On Timer is set and the projector is in the standby mode, the  
Status indicator flashes green (4 sec interval) to show that On Timer program  
is active.  
The projector must be in stand-by mode at the time of turning on.  
The preset power-on time will be void if the cooling fan is working or an error  
occurs. Unplugging the projector cancels your 1 Week programs regardless of  
whether the program was executed or not. However, your Every Week program  
will not be cancelled even if you unplug the projector.  
Source Select (RGB1/2,Video1/2, S-Video, DVI (Digital), DVI (Ana-  
log) and PC Card Viewer), Picture, Volume, Image Options (Key-  
stone, Color Temperatureand and Lamp Mode), Projector Options  
(Menu and Setup), Tools (Capture and PC Card Files) and Help  
(Contents and Information). See page E-36 for instructions about  
how to customize the Basic/Custom Menu.  
Language:  
Sleep Timer  
You can choose one of seven languages for on-screen instructions.  
The options are: English, German, French, Italian, Spanish, Swed-  
ish and Japanese.  
Menu Display Time :  
This option allows you to select how long the projector waits after  
the last touch of a button to turn off the menu.  
The preset choices are "Manual", "Auto 5 sec", "Auto 10 sec", and  
"Auto 30 sec". The "Auto 10 sec" is the factory preset.  
1. Select your desired time between 30 minutes and 2 hours in 30  
minute increments.  
Manual ......... The menu can be turned off manually.  
Auto 5 sec .... The menu will automatically be turned off in 5 seconds if no  
buttons are pressed within 5 seconds.  
Auto 10 sec .. The menu will automatically be turned off in 10 seconds if no  
buttons are pressed within 10 seconds.  
Auto 30 sec .. The menu will automatically be turned off in 30 seconds if no  
buttons are pressed within 30 seconds.  
2. Select Set and press the ENTER button on the remote control.  
3. The remaining time starts counting down.  
4. The projector will turn off after the countdown is complete.  
E – 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Page 2]  
[Page 3]  
Display Select:  
Projector Pointer:  
You can choose the desired status information to be displayed on  
the screen. The desired status information will be displayed each  
time you switch between sources.  
This option is avaiable on the optional presentaion remote control  
(PR50KIT) only.  
This enables you to select from eight different Pointer icons for the  
"Pointer" button on your remote control.  
Date Format:  
After moving your Pointer icon to the area you want on the screen,  
press the Magnify button on the remote control to enlarge the se-  
lected area on the screen.  
Eight display formats can be selected. This date format sets the  
current date that appears on the upper left corner of the screen.  
Date, Time Preset:  
Setting the Current Date and Time  
NOTE: There may be cases where the Pointer function is not available (ex. A  
non-interlace signal at 15kHz such as video game.)  
Direct Button:  
Volume Bar: This option turns on or off the volume bar when you  
adjust the sound volume using Select ▲▼ button on the remote  
control.  
On ................ You can increase or decrease the sound volume with the vol-  
ume bar on screen.  
Off ................ You can increase or decrease the sound volume without hav-  
ing to use the volume bar.  
You can set the current time, month, date, and year.  
Keystone Bar: This option is avaiable on the optional presentaion  
remote control (PR50KIT) only. This option turns on or off the key-  
stone bar when you adjust the keystone using KEYSTONE +/- but-  
ton on the optional presentation remote control.  
1. Type in date.  
Enter month, date and year in this order using INPUT buttons on the  
remote control.  
Month and date must be entered in two digits. For example, to dis-  
play "February", press "0" and "2".  
On ................ You can increase or decrease the level with the keystone bar  
on screen.  
Off ................ You can increase or decrease the level without having to use  
the keystone bar.  
2. Type in time.  
Time is expressed in the 24-hour format. For example, 6:00 p.m. is  
entered as 18:00.  
3. Select "OK" and press ENTER.  
Closing the window allows the clock to start.  
The current year, month, date and time are displayed on the top of  
the screen.  
NOTE: The projector has a built-in clock. The clock will keep working for about  
3 days after the main power is turned off.  
If the main power is off for 3 days or more, the built-in clock will be reset. If the  
built-in clock is reset, set the date and time again.  
The built-in clock will not reset while in the standby condition.  
E – 46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Page2]  
Setup  
Enables you to set operating options.  
Press "OK" to save your changes for all the features of Page1, Page2,  
Page3, Page 4, Page5 and Page6.  
[Page 1]  
Signal Select  
RGB1/2:  
Allows you to choose "RGB" for an RGB source such as a com-  
puter, or "Component" for a component video source such as a  
DVD player. Normally select "Auto" and the projector automatically  
detects a component signal. However there may be some compo-  
nent signals that the projector is unable to detect. If this is the case,  
select "Component".  
Orientation:  
This reorients your image for your type of projection.  
The options are: desktop front projection, ceiling rear projection,  
desktop rear projection, and ceiling front projection.  
VIDEO 1/2 and S-VIDEO:  
Background:  
This feature enables you to select composite video standards manu-  
ally.  
Normally select "Auto".  
Select the video standard from the pull-down menu. This must be  
done for Video and S-Video separately.  
Use this feature to display a blue/ black screen or logo when no  
signal is available.The default background is blue.You can change  
the logo screen using the PC Card Files feature. See page E-50.  
PC Card Viewer Options  
Show Folder List:  
If this option is checked, when PC Card Viewer input is selected on  
the projector, the folder lists will be displayed and allows you to  
select the presentation from a PC card.  
Auto Play:  
If this option is checked, any given slide will start to play automati-  
cally.  
Auto Play Interval:  
You can specify interval time between 5 and 300 seconds.  
NOTE: The Auto Play Interval time set on the PC Card Viewer Utility over-  
rides the one set here.  
Manual Play:  
Views a slide manually when PC Card Viewer input is selected.  
NOTE: The Auto Play and Manual Play options determine the behavior of  
the Play/Stop [  
/
] icon on the Viewer toolbar.  
NOTE: If you check "Auto Play" and select "PC Card Viewer" on the projector,  
the slides will automatically start to play back from any given slide.  
Capture Options: (available for JPEG only)  
These options are used for the Capture function that you can select  
from Tools.You have three options for JPEG compression quality:  
High quality, Normal and High Compression.  
High Quality ...............Gives quality of JPEG a priority.  
Normal .......................Gives normal JPEG quality.  
High Compression .....Gives compression a priority.  
E – 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Page 3]  
Power Management:  
When this option is on and there is no RGB input for five minutes or  
more, the projector will automatically turn itself off.  
Power Off Confirmation:  
This option determines whether a confirmation dialog for turning off  
the projector will appear or not.  
Keystone Save:  
This option enables you to save your current keystone settings.  
Saving your change once affects all sources.The changes are saved  
when you turn off the projector.  
Fan High Speed Mode:  
This option allows you to select two modes for fan speed: high-  
speed mode and normal speed mode.  
When you wish to cool down the temperature inside the projector  
quickly, check this box.This is convenient especially when the pro-  
jector is installed on the ceiling.  
Signal Select (RGB connector):  
Built-in Speaker:  
Allows you to choose "VIDEO" or "S-VIDEO" for RGB 1 or 2 con-  
This option allows you to activate the built-in speakers when you  
connect an audio cable to the AUDIO OUT terminal.  
nector.  
Normally select "Auto".  
Clear Lamp Hour Meter:  
[Page 4]  
Resets the lamp clock back to zero. Pressing this button appears a  
confirmation dialog box.To reset the lamp usage hour, press "OK".  
NOTE: The projector will turn off and go into standby mode after 1600 hours  
(up to 2100 hours in Eco mode) of service. If this happens, press the "Help"  
button on the remote control for ten seconds to reset the lamp clock back  
to zero. Do this only after replacing the lamp.  
Clear Filter Usage:  
Resets the filter usage back to zero. Pressing this button appears a  
confirmation dialog box. To reset the filter usage hour, press "OK".  
Auto Adjust (RGB Only):  
When "Auto Adjust" is set to "On", the projector automatically de-  
termines the best resolution for the current RGB input signal to  
project an image using NEC's Advanced AccuBlend Intelligent Pixel  
Blending Technology.  
The image can be automatically adjusted for position and stability;  
"Horizontal Position", "Vertical Position", "Clock", "Phase", and  
"Resolution."  
On ................ Automatically adjusts image display functions ("Video Filter",  
"Horizontal Position", "Vertical Position", "Clock", "Phase" and  
"Resolution".)  
Off ................ User can adjust the image display functions ("Video Filter",  
"Horizontal Position", "Vertical Position", "Clock", "Phase" and  
"Resolution") manually.  
NOTE: The projector has a feature that enters a signal automatically in the Entry  
List once you made any adjustments. However, this feature is not available if  
you adjust a signal using the Auto Adjust feature. To register the signal after  
you use the Auto Adjust feature, first you need to make any one adjustment  
manually.  
Auto Start:  
Turns the projector on automatically when the power cable is in-  
serted into an active power outlet. This eliminates the need to al-  
ways use the "Power" button on the remote control or projector cabi-  
net.  
E – 48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Page 5]  
Default Source Select:  
You can set the projector to default to any one of its inputs each  
time the projector is turned on.  
Last .............. Sets the projector to default to the previous or last active  
input each time the projector is turned on.  
Auto ............. Searches for an active source in order of RGB1 → RGB2 →  
Video 1 → Video 2 → S-Video → PC Card Viewer → DVI  
Digital → DVI Analog → RGB1(Standalone) and displays the  
first found source.  
Searching order in SW1 Level: from Slot 1 to 10  
Searching order in SW2 Level: from Master projector 01,  
Slave projector 01 to Master projector 10, Slave projector 10  
Select ........... Displays the selected source input every time the projector is  
started up. Select an input from the pull-down menu.  
Link Mode (not available for DVI digital)  
Remote Sensor:  
This option determines which remote sensors on the projector are  
enabled in wireless mode.  
The options are: front, rear, right, or left. All checked boxes indicate  
that they can accept the infrared signal from the supplied remote  
control.  
This feature is used for multiple projector connection using RGB  
Digital Input/Output connectors.The master projector is set to Master.  
The other slave projectors are set to Slave.When not using Link mode,  
set to Standalone. See page E-16 for setting up for double stacking in  
link mode.  
S-Video Mode Select:  
This feature is used to select the S-Video signal detection mode.  
This allows identifying of the S-Video signals with different aspect  
ratio (Zoom signal 16:9, Wide Zoom signal 4:3).  
Switcher Control  
S2 ................ Identifies Zoom or Wide Zoom signal.  
OFF .............. Does not identify any S-video signal.  
This feature sets the projector in communication with the NEC ISS-  
6020 Switchers.  
[Page 6]  
Stand Alone ................ Use the projector in stand alone operation.  
SW 1 Level..................Use the projector with one Switcher. (not available  
in Link mode)  
SW 2 Level..................Use the projector with two or more Switchers. (not  
available in Link mode)  
When changing this setting, the confirmation message will appear. If  
you want to restart your projector, select Yes; if not, select No.  
NOTE: This setting becomes effective only after the projector is restarted.  
Communication Speed:  
This feature sets the baud rate of the PC CONTROL connector  
(Mini D-Sub 9 Pin).  
It supports data rates from 4800 to 38400 bps.  
The default is 38400 bps. Select the appropriate baud rate for your  
equipment to be connected.  
Projector ID  
Each projector needs its own unique addresses when used in se-  
rial communication mode. You can choose one of 64 unique ad-  
dress using the spin box. First select Enable. Keep pressing in-  
creases the number.  
To make your setting available, select OK.  
E – 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PC Card Files:  
Tools  
Displays a list of all the files stored in the PC card so that you can  
select a file you want to display.You can also sort files by file name  
or date, or display the file.  
Although a list of all the files in the PC card is displayed, you can  
view files in idx, text, HTML, JPEG and BMP format only.  
Selecting BMP and JPEG files automatically switches to the PC  
Card Viewer source.  
NOTE: When an image with a resolution of XGA (1024 x 768) or higher is  
projected, the PC Card Files screen may not be correctly displayed.  
Provides tools for capturing images and displaying files in a PC Card.  
NOTE: The "Capture" and "PC Card Files" features are required for a PC card.  
Capture:  
Allows you to capture an image from a source that is currently be-  
ing displayed. The image is saved as JPEG in the PC card.  
When you select Capture from the menu, you will get a tool bar.You  
can capture an image directly using the tool bar when the menu is  
not displayed.  
Freeze  
Exit  
Selecting "Execute" displays the file you selected.  
Capture  
When you select a JPEG or BMP file and press the Enter button on  
the remote or the cabinet, or "Execute" on the above, you will get a  
toolbar. This toolbar is used to return to the PC Card Files screen.  
The tool bar includes the following buttons:  
Capture ........ Captures an image and save it as a JPEG file in a PC card.  
Freeze .......... Freezes and unfreezes images.  
Return  
Close  
Exit............... Exits the Capture function.  
Return .......... Returns to the PC Card Files screen.  
Close ............ Close the toolbar.  
Unless a PC card is inserted into the PC Card slot of the projector,  
the Capture feature is not available.  
The "Card Error" display means that the free space of the PC card  
is insufficient for saving images. Make more space available on the  
card by erasing unwanted images with your PC. The number of  
images that can be captured depends on the size of the PC card.  
Changing Background Logo:  
The Logo button allows you to select a background logo from graphic  
files on a PC card and change to it as the background logo.  
NOTE: File size must be 64KB or less. Other file formats than JPEG and  
BMP are not available.  
NOTE: Be sure not to turn off the power or remove the PC card while cap-  
turing an image. Doing so could cause a loss of the data in the PC card or  
damage to the card itself.  
1. Use the ▲ or ▼ button to select a JPEG or BMP file for your background  
logo.  
NOTE: Captured images with higher resolution than the projector's native  
resolution cannot be displayed correctly.  
ᮣ
2. Use the and then ▼ button to select "Logo".  
3. Press the Enter on the remote control or the cabinet. You will get the  
confirmation dialog box.  
4. Select "OK" and press the Enter button. This completes changing a logo  
for the background.  
* Once you have changed the background from the NEC logo to another, you  
cannot return the logo to background even by using Factory Default. To  
do so, repeat the above steps. The NEC logo file is included on the sup-  
plied CD-ROM (/logo/nec_b_x.jpg).  
E – 50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[Page 6]  
Help  
Contents:  
Provides an online help about how to use the menus. An under-  
lined link means that you can move to an adjustment item directly.  
Selecting the underlined link and pressing ENTER moves to the  
corresponding adjustment item.  
Link Mode:  
NOTE: The Help Menu may not be displayed correctly when a UXGA signal  
Displaying Current Status of Link Mode  
When selecting the tab "Page 6 ", you will get the following dialog  
box.  
is displayed.  
Information:  
Displays the status of the current signal, and the lamp and the pro-  
jector usage hours.  
This dialog box has six pages.  
Master ID ....................Indicates the Master projector  
Status ......................... Indicates the status of the master projector  
Connected PJ ..............Indicates number of connected slave projectors  
Slave No. ....................Indicates serial number of the slave projector  
ID ................................Indicates ID of a slave projector  
[Page 1]  
[Page 2]  
Signal Type  
Video Type  
Sync Type  
Interlace  
Resolution  
Direct Key (See also page E-41)  
Source Name  
Input Terminal  
Entry No.  
Horizontal Frequency  
Vertical Frequency  
Sync Polarity  
Status ......................... Indicates the status of the slave projector  
ᮤ ᮣ  
Page buttons  
........ Turns pages. One screen displays information of 3  
projectors only. Information of a maximum of 16  
projectors can be displayed using these page but-  
tons.  
Reconnect button ....... Confirms connection of all linked projectors  
[Page 3]  
[Page 4]  
Aspect Ratio (IN/OUT)  
Gamma Correction  
Noise Reduction  
Color Matrix  
Lamp Remaining Time (%)  
Lamp Hour Meter (H)  
Filter Usage (H)  
Projector Usage (H)  
Projector ID  
Status items:  
Running ...................... The projector is now working  
Cooling Lamp ............. The fan is now cooling the lamp  
Standby ...................... The projector is in stand-by  
Communication Error . A communication error has occurred  
Connecting..................The projector is now verifying for connection  
Error Standby ............. An error caused the projector to enter the stand-by  
mode  
Matrix Type  
NOTE: The progress indicator shows the percentage of remaining bulb life.  
The value informs you of the amount of lamp, filter and projector usage  
respectively.  
Test Pattern  
[Page 5]  
Version (BIOS/Firmware/Data/SUB-CPU)  
Nine test patterns can be selected.You can turn on or off red, green, or  
blue respectively.  
E – 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ejecting the PC Card  
Using the PC Card Viewer function  
Press the eject button. The PC card pops out a little. Grasp the edges  
of the PC card and pull it out. Do not eject the PC card while its data is  
being accessed.  
NOTE: When using the supplied software (CD-ROM)  
The software is designed to use with a personal computer only. Do not play the  
software on CD player. Doing so could cause damage to speakers.  
Eject button  
Features  
The Viewer feature allows slides stored on a PC memory card (re-  
ferred to as PC card in this manual) to be displayed on the projector.  
Even if no computer is available, presentations can be conducted sim-  
ply with the projector. This feature is convenient for holding presenta-  
tions at meetings and in offices, as well as for playing images taken on  
digital cameras.  
Easy to use  
• Presentations can be started immediately simply by inserting a PC  
card (not supplied)  
• Easy slide switching  
• Remote control operation  
• Jumping to list of slides or any specific slide  
High quality images  
• High resolution up to 1024
ן
768 dots  
• 24-bit full color playback  
Direction for Inserting the PC Card  
The PC card has a top and bottom and must be inserted into the  
PC card slot in a specific direction. It cannot be inserted backwards  
or upside-down. Attempting to force it into the slot in the wrong  
direction may break the internal pin and damage the card slot.  
Refer to the PC card's operating instructions for the proper direc-  
tion of insertion.  
• Viewing of digital camera images  
Simple utility software (for computer)  
• PC Card Viewer Utility operable on Windows 95 / 98 / NT4.0 (SP3 or  
later) / 2000  
• Slides can be created by capturing the currently displayed image  
• Control screen for displaying lists of slides and editing  
• PC Card Viewer PPT Converter 1.0 [Add-In Version] converts files  
created with Microsoft PowerPoint 95/97/2000 (hereafter referred to  
as PowerPoint) into indexes playable with PC Card Viewer  
PC Card Type  
The PC Card slot accepts PCMCIA Type II only.  
* Microsoft, Windows and PowerPoint are registered trademarks of  
Microsoft Corporation.  
Inserting and Ejecting a PC Card  
A PC card is used to view presentation data prepared on the computer  
and to capture and play images projected with the projector.  
Inserting the PC Card  
• Hold the PC card horizontally and insert it slowly into the card slot  
with its top facing up.  
• The eject button pops out once the PC card is fully inserted.  
Check that the PC card is fully inserted.  
NOTE: Do not try to force the PC card into the slot.  
PC Card  
E – 52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the PC Card Viewer Software  
Starting Up the PC Card Viewer Software  
on your PC  
Before Installing  
Perform the following before installing the PC Card Viewer software:  
• If Windows is already started, exit all applications. Installation may  
not be performed properly if any applications are running.  
(PC Card Viewer Utility 1.0)  
Use the PC Card Viewer Utility 1.0 for creating viewer slides.  
To start the PC Card Viewer software:  
* Select [Start]-[Programs]-[NEC Projector Tools]-[PC Card Viewer  
Utility 1.0].  
Installation  
Install the viewer software as described below.  
To quit installation before it is completed, press the "Cancel" button  
then follow the instructions in the dialog box.  
1. Start up Windows.  
2. Insert the CD-ROM into the CD-ROM drive.  
The auto CD play function automatically starts the CD-ROM's  
program and the contents screen appears.  
Refer to online help for instructions on using the PC Card Viewer soft-  
ware.  
* The auto CD play function operates if the "Auto insert notification" box in  
the computer's CD-ROM control panel is checked. (The box is checked  
by default.)  
3. Click [Installing the PC Card Viewer Utility 1.0]  
The setup dialog appears.  
Contents of the English version PC Card Viewer software  
(PC Card Viewer Utility 1.0)  
This is the software used for creating PC Card Viewer slides. In this  
manual it is referred to as the "PC Card Viewer software".  
PC Card Viewer PPT Converter 1.0  
* Follow the instructions in the setup dialog to complete the installation.  
This is an application that converts files created with Microsoft  
PowerPoint 95/97/2000 into indexes so that they can be played directly  
with the PC Card Viewer Utility 1.0.  
For instructions on uninstalling the PC CardViewer software, see page  
E-50.  
PC Card Viewer PPT Converter is installed automatically when you  
install the PC Card Viewer Utility.  
To start PC Card Viewer PPT Converter:  
* Select PC Card Viewer PPT Converter from NEC Projector Tools.  
Basic Operation of the PC Card Viewer Software  
PC Card Viewer Utility is an application for editing documents, con-  
verting them into slides and storing them on PC cards as playback  
data (indexes) for presentations using projectors.  
E – 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jump ......... Displays a list of slides while you are playing back.  
Select ........ Displays a list of folders while you are playing back.  
Operating the PC Card Viewer Function  
from the Projector (playback)  
Setup ........ Displays the PC Card Viewer Options dialog box on Page 1 of  
the Setup dialog box.  
Delete ........ Deletes a captured slide(s) or all the captured slides in the  
Capture – specific folder.  
View .......... Hides the tool bar while you are playing back. Pressing the  
MENU button shows it again.  
This section describes the operation for showing slides of presentation  
documents created using the PC Card Viewer function with the projec-  
tor.  
It is also possible to make slides directly from the images projected  
with the projector.  
Projecting slides  
NOTE: If no PC card is inserted in the PC CARD slot, there is no signal, and a  
black, blue or logo background is displayed, depending on the setting.  
1. Insert a PC card into the card slot.  
Insert the PC card with the side with the insertion direction arrow  
on the top.  
ᮤ
ᮣ
Playback is stopped when  
/
button on the cabinet or the supplied  
remote control or SLIDE +/- on the optional presentation remote con-  
trol is pressed in Auto Play mode.  
* Press the eject button to eject the card.  
2. Select the “PC Card Viewer” from the Source Select menu.  
NOTE: Up to 12 indexes can be displayed on the list of folders. The folder in the  
right bottom is always a folder exclusively for captured images, but is only  
displayed when images have been captured. To display the list of folders when  
there are 13 or more indexes stored on the PC card, select "Edit index" from the  
PC Card Viewer software's "File" menu and move the index you want to display  
to within 12 indexes from the top of the folder index. For details on indexes,  
refer to the PC Card Viewer software's help folder.  
Optional Presentation Remote Control  
OFF  
ON  
-
VIDEO S VIDEO AUTO ADJ.  
3. Project slides.  
Checking “Show Folder List”, means that selecting PC Card Viewer  
input displays a list of the folders in the PC card and if “Auto Play” is  
checked the projector automatically starts to play slides at the first  
slide of the folder you have selected.  
RGB 1  
RGB 2  
P
J
MENU  
LASER  
A tool bar will appear when you press the MENU button on the remote  
control or the projector cabinet.  
Prev  
Play Jump Setup  
View  
Next  
Stop Select  
Delete  
R-CLICK /CANCEL  
HELP POINTER PC CARD  
The tool bar includes the following buttons:  
KEYSTONE MAGNIFY SLIDE  
Prev .......... Returns to the previous slide or folder. Or this lets you play  
slides back in reverse.  
FREEZE VOL. FOLDER  
Next .......... Advances to the next slide or folder. Or this lets you play  
slides back.  
-
PIC MUTE  
SLIDE  
Play ........... Plays back automatically or manually depending on the set-  
ting on PC Card Viewer Options of the menu. This allows you  
to move on to the next slide when “Manual Play” is selected.  
LIST  
Stop .......... This allows you to stop Auto Play while you are playing back  
and to resume playing from the selected slide or folder when  
“Auto Play” is selected.  
E – 54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When the tool bar is not displayed:  
Auto Play Mode  
ᮤ
ᮣ
Press select or , or the FOLDER LIST button on the optional remote  
control to display folders from a PC card in the projector’s PC Card slot.  
• If the “Auto Play” option is selected in “PC Card Viewer Options” of  
the menu, any given slide will start to play automatically. You can  
also specify Auto Play Interval between 5 and 300 seconds.  
Multi cursor (blue marks)  
Switching to Slides Directly from Other Input  
Modes  
Folder  
Folder  
Folder  
Folder  
SLIDE  
Folder  
With this function it is possible to switch directly to a slide when the  
picture of a VCR or computer is being projected.  
Example:  
When conducting presentations using a combination of slides and  
moving pictures from a VCR, etc., it is possible to switch from a PC  
CardViewer slide to the video picture then back to the PC Card Viewer  
slide simply by using a source button and PC CARD button.  
Serial number of folder  
containing selected slide  
02 : 0001 / 0008  
Number of all slides  
in folder  
Serial number of  
selected slide  
NOTE: Even if you switch the current PC Card Viewer source to another source,  
the current slide is retained. When you return back to the PC Card Viewer, you  
will get the slide that has been retained.  
ᮤ
ᮣ
or , or the  
Use the select  
SLIDE +/- button to advance to  
the next folder or return to the  
previous folder.  
Optional Presentation Remote Control  
Folder  
OFF  
ON  
Slide(Table) cursor (green marks)  
-
VIDEO S VIDEO AUTO ADJ.  
Slide  
Slide  
Slide  
Slide  
Slide  
Slide  
Slide  
RGB 1  
RGB 2  
PJ  
Slide  
MENU  
LASER  
02 : 0004 / 0008  
ᮤ
ᮣ
Use the select or , or the  
SLIDE +/- button to advance  
to the next slide or return to the  
previous slide.  
Slide  
R-CLICK /CANCEL  
HELP POINTER PC CARD  
KEYSTONE MAGNIFY SLIDE  
ᮤ
ᮣ
NOTE: You can also use the and button on the remote control (supplied or  
FREEZE VOL. FOLDER  
optional) to select folders or slides.  
ᮤ
ᮣ
If you use the and button on the remote control for PC Card Viewer opera-  
tion, press the PJ button to switch to the Projector mode and the PJ button  
lights red.  
-
PIC MUTE  
SLIDE  
LIST  
RGB 1  
RGB 2  
P
J
Lit red  
MENU  
LA
Works as the Select button  
on the projector.  
NOTE: The PC card editing operation cannot be performed from the projector.  
Do so using the PC Card Viewer software.  
E – 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Deleting Captured Images  
Capturing Images Displayed on the Projector  
Prev  
Play Jump Setup  
View  
Storing images displayed on the projector on the PC card  
Preparations:  
Insert the PC card into the card slot.  
Insert the PC card with the side with the insertion direction arrow on  
the top.  
Next  
Stop Select  
Delete  
* Press the eject button to eject the card.  
Using the Delete button on the tool bar for PC Card Viewer can delete  
captured images.  
1. Project the image you wish to store on the projector.  
2. Select the “Capture” from the Tools menu.  
To delete captured images:  
1. Select PC Card Viewer.  
ᮣ
2. Use button to select the Capture folder in the right bottom of  
the screen.  
Freeze  
3. Press the MENU button to display the tool bar.  
ᮤ
ᮣ
4. Use the or button to select the Delete icon and press the  
ENTER button.  
Capture  
Viewing Digital Images  
Exit  
Digital images can be played with the PC Card Viewer if the following  
conditions are met:  
3. A tool bar will appear.  
• If the image can be stored on an MS-DOS format PC card  
• If the image can be stored in a format supported by the PC Card  
Viewer.  
With the PC Card Viewer, images on the card are searched for in  
directories and images in JPEG or BMP format are recognized as  
slides.  
The tool bar includes the following buttons:  
Capture ........ Captures an image and save it as a JPEG file in a PC card.  
Freeze .......... Freezes and unfreezes images.  
Searchable directories are directories within two steps from the root  
directory, and searchable images are images within the first 12 files  
in the directory. Only file and slide switching are possible.  
Exit............... Exits the Capture function. Another option to exit the Capture  
function is to press MENU or CANCEL button on the remote  
control or projector cabinet.  
NOTE: The maximum number of images recognized as slides within one direc-  
tory is 128.  
NOTE: You can compress a captured file (JPEG) using the Capture Options in  
the Setup dialog. See page E-47.  
NOTE: Captured images with higher resolution than the projector's native reso-  
lution cannot be displayed correctly.  
NOTE:  
•
File size of the captured image varies depending on the resolution of an  
input signal.  
•
Since an image data is compressed with the JPEG format, the image is slightly  
degraded.  
NOTE: An hourglass indicating that an image is being captured appears on the  
projector's display. Do not eject the PC card or turn off the projector's power  
while this icon is displayed. Doing so will damage the PC card data. If the PC  
card data is damaged, use a computer to repair the data.  
NOTE: The folder in the right bottom is always a folder exclusively for captured  
images. To display the list of folders when there are 13 or more indexes stored  
on the PC card, select "Edit index" from the PC Card Viewer software's "File"  
menu and move the index you want to display to within 12 indexes from the top  
of the folder index. For details on indexes, refer to the PC Card Viewer software's  
help file.  
E – 56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. In the "Add/Remove Programs Properties" dialog box, click the  
"Setup/Remove" tab, then select "PC Card Viewer Utility 1.0" from  
the list of applications and click on "Add/Remove".  
Uninstalling the PC Card Viewer Software  
Even if you do now know the PC Card Viewer software's file names or  
where they are stored, the PC Card Viewer software files can be easily  
removed from the system using the "Install/Uninstall Applications" con-  
trol panel in Windows. (Normally there is no need to perform this op-  
eration.)  
Uninstalling the software  
Use the procedure described below to uninstall the PC Card Viewer  
software files.  
1. From the "Start" menu, select "Settings" then "Control Panels".  
4. In the "Confirm File Deletion" dialog box, click "Yes".  
2. In the "Control Panels" dialog box, double-click on "Add/Remove  
Programs".  
5. Once the application is uninstalled, click on "OK" in the "Remove  
Program From Your Computer" dialog box.  
E – 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. MAINTENANCE  
This section describes the simple maintenance procedures you should  
follow to replace the lamp and clean the filter.  
3. Insert a new lamp housing until the lamp housing is plugged into  
the socket.  
CAUTION: Do not use a lamp other than the NEC replacement lamp  
(GT50LP). Order this from your NEC dealer.  
Replacing the Lamp  
After your lamp has been operating for 1500 hours (2000 hours : Eco  
mode) or longer, the “Status” light in the cabinet will go on and the  
message will appear. Even though the lamp may still be working, re-  
place it at 1500 (up to 2000 hours : Eco mode) hours to maintain opti-  
mal projector performance.  
Secure it in place with the two screws.  
Be sure to tighten the screws.  
M
E
N
U
S
O
U
R
C
E
A
U
A
T
O
D
J
U
S
T
O
N
/
S
T
A
N
CAUTION  
D
R
B
Y
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will  
be extremely hot. Turn the projector off, wait a full minute, and then  
disconnect the power cable. Allow at least one hour for the lamp to  
cool before handling.  
M
E
N
U
•
•
DO NOT REMOVE ANY SCREWS except the lamp cover screw and two  
lamp housing screws. You could receive an electric shock.  
The projector will turn off and go into stand by mode after 1600 (2100  
hours : Eco mode) hours of service. If this happens, be sure to replace  
the lamp. If you continue to use the lamp after 1500 hours (2000 hours  
: Eco mode) of use, the lamp bulb may shatter, and pieces of glass may  
be scattered in the lamp housing. Do not touch them as the pieces of  
glass may cause injury. If this happens, contact your NEC dealer for  
lamp replacement.  
SELECT  
E
R
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
P
A
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
To replace the lamp:  
1. Loosen the lamp cover screw until the screwdriver goes into a  
freewheeling condition and remove the lamp cover. The lamp cover  
screw is not removable.  
4. Reattach the lamp cover.  
Tighten the lamp cover screw.  
Be sure to tighten the screw.  
L
E
M
E
F
U
T
P
N
U
L
E
S
N
E
L
S
E
S
C
H
T
I
F
T
D
O
S
O
U
W
N
R
IG  
S
O
RC  
E
H
T
C
A
U
R
C
N
C
E
L
E
M
E
N
AU  
U
A
TO  
DJU  
A
U
A
T
S
T
D
O
J
U
S
S
T
S
E
E
T
L
A
N
E
T
U
C
T
S
T
E
O
N
R
ND  
/
S
T
P
BY  
O
A
N
W
E
D
R
B
Y
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
U
P
N
S
S
H
I
F
T
R
I
G
H
T
M
E
N
U
S
E
E
L
N
E
C
T
T
E
R
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
2. Loosen the two screws securing the lamp housing until the screw-  
driver goes into a freewheeling condition. The two screws are not  
removable.  
Remove the lamp housing by pulling out the handle.  
NOTE: There is an interlock on this case to prevent the risk of electrical  
shock. Do not attempt to circumvent this interlock.  
5. After you install a new lamp, select [Menu] → [Projector Op-  
tions] → [Setup]→[Page 4]→[Clear Lamp Hour Meter] to reset  
the lamp usage hours.  
S
O
U
R
C
E
A
U
A
T
O
D
J
U
S
T
N
/
S
T
A
N
D
B
Y
NOTE: When the lamp exceeds 1600 hours (2100 hours : Eco mode) of ser-  
vice, the projector cannot turn on and the message is not displayed. If this  
happens, press Help button on the remote control for a minimum of 10 sec-  
onds while in standby mode. When the lamp time clock is reset to zero, the  
STATUS indicator goes out.  
M
E
N
U
SELECT  
S
O
C
U
R
A
N
A
C
E
L
C
E
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
Interlock  
E – 58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To replace the filter:  
Cleaning or Replacing the Filter  
The air-filter sponge keeps the inside of the MultiSync GT1150 Projec-  
tor free from dust or dirt and should be cleaned after every 100 hours  
of operation (more often in dusty conditions). If the filter is dirty or  
clogged, your projector may overheat.  
1. Pull out the filter by pushing up on the catch.  
CAUTION  
•
Turn off the power, wait for a full minute, and unplug the projector  
before replacing the filter.  
•
•
•
Only clean the outside of the filter with a vacuum cleaner.  
Do not attempt to operate the projector without filter.  
Your projector will not operate unless the filter is installed correctly.  
IN  
P
C
C
O
N
T
R
O
O
L
U
T
R
E
IN  
M
O
T
E
R
To clean the filter:  
Pull out the filter by pushing up on the catch.Vacuum the filter-through  
the filter.  
E
1
M
O
2
T
E
O
U
S
T
C
,
T
R
A
C
IG  
IN  
G
E
R
V
B
T
V
L
E
V
O
E
O
C
R
N
O
R
G
B
R
L
1
/
Y
/
H
/
H
V
B
IN  
P
/
C
C
b
L
C
/
M
O
N
O
V
N
O
T
R
A
O
O
R
L
U
I
T
R
E
T
IN  
M
O
T
E
R
E
1
M
O
2
T
E
O
U
S
T
C
,
T
A
R
C
IG  
IN  
G
E
R
I
I
2
O
R
IN  
P
C
T
C
1
I
O
O
L
/
N
O
R
T
R
2
R
O
O
O
L
U
R
T
G
R
B
R
E
1
IN  
M
O
V
L
Y
T
E
R
O
E
O
E
N
1
M
O
2
/
H
T
V
E
O
U
B
S
/
T
C
C
b
L
,
T
/
M
O
V
A
R
N
C
IG  
O
IN  
G
E
U
R
R
I
N
I
U
O
T
I
O
/
R
2
R
r
N
O
G
B
R
1
-
V
L
/
Y
E
O
N
H
/
H
V
B
/
C
b
L
/
M
O
V
N
O
U
R
2. Reinstall the new filter.  
NOTE: Do not detach the sponge from the filter. Do not wash the filter with  
soap and water. Soap and water will damage the the filter membrane. Be-  
fore replacing the filter cover, remove dust and dirt from the projector cabi-  
net. Keep out dust and during filter replacement.  
3. After you install a new lamp, select [Menu] → [Projector Op-  
tions] → [Setup] → [Page 4] → [Clear Filter Usage] to reset the  
filter usage hours.  
E – 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cette section décrit les procédures simples d’entretien que vous devez  
suivre pour remplacer la lampe, nettoyer ou remplacer le filtre.  
3. Insérez un coffret de lampe neuve dans la prise.  
ATTENTION: N’utilisez pas une lampe autre que la lampe de remplacement  
NEC (GT50LP). Commandez-la de votre revendeur NEC.  
Remplacement de la lampe  
Fixez-le à l’aide de deux vis.  
Assurez-vous de visser les deux vis.  
Après que votre lampe ait fonctionné pendant 1500 heures (2000 heures  
: mode Eco) ou plus, le voyant “Status” du coffret s’allume. Même si la  
lampe peut encore fonctionner, remplacez-la au bout de 1500 heures  
(2000 heures : mode Eco) pour conserver une performance optimale  
de votre projecteur.  
M
E
N
U
S
O
U
R
C
E
A
U
A
T
O
D
J
U
S
T
O
N
/
S
T
A
N
D
R
B
Y
ATTENTION  
•
NE TOUCHEZ PAS A LA LAMPE juste après qu’elle ait été utilisée. Elle est très  
chaude. Eteignez le projecteur laisse au moins 60 secondes d’intervalle après  
avoir éteint le projecteur et débranchez le câble d’alimentation. Laissez la refoidir  
pendant au moins une heure avant de la manipuler.  
M
E
N
U
SELECT  
E
R
S
O
C
U
R
A
N
A
C
E
L
C
E
•
•
NE RETIREZ PAS LES VIS excepté la vis du couvercle de la lampe et deux vis  
du coffret de la lampe. Une décharge électrique pourrait en résulter.  
L
A
M
P
A
U
A
T
O
D
J
U
S
S
T
T
T
U
S
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
Le projecteur s’éteint et entrer en mode d’attente après 1600 heures  
(2100 heures : mode Eco) de service. Dans ce cas, remplacez la lampe.  
Si vous continuez à utiliser la lampe après 1500 heures (2000 heures :  
mode Eco) d’utilisation, l’ampoule de la lampe risque d’éclater, et des  
bris de glaces risquent d’être dispersés dans le boîtier de la lampe. Ne  
les touchez pas car elles peuvent vous blesser. Dans ce cas, contactez  
votre revendeur NEC afin de procéder au remplacement de la lampe.  
Pour remplacer la lampe:  
4. Refixez le couvercle de la lampe.  
1. Dévissez la vis du couvercle de la lampe jusqu’à ce que le tournevis  
tourne librement et retirez le couvercle de la lampe. La vis du  
couvercle de la lampe ne peut pas être retirée.  
Serrez la vis du couvercle de la lampe.  
Assurez-vous de visser la vis du couvercle de la lampe.  
L
E
M
E
F
U
T
P
N
U
L
E
S
N
E
L
S
E
S
C
H
T
I
F
T
D
O
S
W
N
R
O
U
IG  
S
RC  
E
O
H
C
A
U
R
C
T
N
C
E
L
E
M
E
N
AU  
U
A
TO  
DJU  
A
U
A
T
S
T
D
O
J
U
S
S
T
S
E
E
T
L
A
N
E
T
U
C
T
S
T
E
O
N
R
ND  
BY  
/
S
T
P
O
A
N
W
E
D
R
B
Y
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
U
P
N
S
S
H
I
F
T
R
I
G
H
T
M
E
N
U
S
E
E
L
N
E
C
T
T
E
R
S
O
C
U
R
A
N
A
C
E
L
C
E
L
A
M
A
P
U
A
T
O
D
J
U
S
S
T
T
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
2. Dévissez les deux vis fixant le coffret de la lampe jusqu’à ce que le  
tournevis touren librement. Les deux vis ne peuvent pas être  
retirées.  
Retirez le coffret de la lampe en tirant la poignée.  
REMARQUE: Il y a un contact de sécurité sur le boîtier pour éviter le risque  
d’électrocution. N’essayez pas de contourner ce contact de sécurité.  
5. Après avoir installé une lampe neuve, sélectionnez [Menu] →  
[Options Projecteur] → [Réglage] → [Page 4] → [Durée  
d’utilisation lampe] pour remettre le compteur d’heures  
d’utilisation de la lampeà zéro.  
S
O
U
R
C
E
A
U
A
T
O
D
J
U
S
T
N
/
S
T
A
N
D
B
Y
REMARQUE: Si la lampe a servi pendant plus de 1600 heures (2100 heures :  
mode Eco), le projecteur ne peut pas être allumé et le menu n’est pas affiché. Si  
cela se produit, appuyez sur le bouton HELP sur la télécommande pendant au-  
moins 10 secondes pendant le mode de veille. Lorsque le compteur de durée  
d’utilisation de la lampe est remis sur zéro, le témoin STATUS disparaît.  
M
E
N
U
SELECT  
S
O
C
U
R
A
N
C
E
L
C
E
A
M
P
A
U
A
T
O
D
J
U
S
S
T
T
A
T
U
S
O
N
/
S
T
P
O
A
N
W
E
D
R
B
Y
Contact de sécurité  
E – 60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pour remplacer le filtre à air:  
Nettoyage ou remplacement du filtre  
Le coussin éponge du filtre à air maintient l’intérieur du projecteur  
GT1150 à l’abri de la poussière ou de la saleté et doit être nettoyé  
toutes les 100 heures d’utilisation (plus souvent dans les endroits  
poussiéreux). Si le filtre est sale ou bouché, le projecteur risque de  
surchauffer.  
1. Retirez-vous le le filtre en poussant au-dessus sur la prise.  
PRECAUTION  
•
Coupez l’alimentation et débranchez le projecteur avant de remplacer  
le filtre.  
•
•
•
Nettoyez uniquement le couvercle extérieur du filtre avec un aspirateur.  
N’essayez pas de faire fonctionner le projecteur sans filtre.  
Votre projecteur à affichage à cristaux liquides ne fonctionnera pas  
tant que le filtre ne sera pas installé correctement.  
IN  
P
C
C
O
N
T
R
O
O
L
U
T
R
E
IN  
M
O
T
E
R
E
1
M
O
2
T
E
O
U
S
T
C
,
T
R
A
C
IG  
IN  
G
E
R
Pour nettoyer le filtre à air:  
Aspirez le filtre à travers le couvercle de filtre.  
V
B
T
V
E
V
O
E
O
C
R
N
O
R
G
B
R
1
L
/
Y
/
H
/
H
V
B
/
C
b
L
/
M
O
V
N
O
A
R
I
T
IN  
PC  
C
O
N
TR  
O
O
L
U
T
RE  
IN  
M
O
TE  
1
R
E
M
O
2
T
E
O
U
S
T
C
,
T
A
R
C
IG  
IN  
G
E
R
IN  
P
C
C
O
N
T
R
O
O
L
U
T
R
E
IN  
M
O
T
R
E
E
1
M
O
2
T
E
O
U
S
T
C
,
T
I
A
R
C
I
G
IN  
G
E
R
I
2
O
R
T
1
I
O
L
/
O
R
2
R
O
R
G
B
R
1
G
V
L
Y
O
E
O
N
/
H
V
B
/
C
b
L
/
M
O
V
N
O
U
R
I
N
I
U
O
T
I
O
/
R
R
r
O
G
B
R
1
-
V
/
Y
E
O
N
H
/
H
V
B
/ C  
b
L
/
M
O
V
N
O
U
R
U
2. Réinstallez le panneau du filtre.  
REMARQUE: Ne détachez pas le coussin éponge du couvercle de filtre. Ne  
lavez pas le filtre au savon et à l’eau. Le savon et l’eau endommageront la  
membrane du filtre. Avant de remplacer le filtre à air, dépoussiérez et nettoyez  
le coffret du projecteur. Maintenez propre pendant le remplacement du filtre.  
3. Après avoir installé un filtre neuve, sélectionnez [Menu] → [Op-  
tions Projecteur] → [Réglage] → [Page 4] → [Pour effacement  
filtre] pour remettre le compteur d’heures d’utilisation de le filtre  
zéro.  
E – 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. TROUBLESHOOTING  
This section helps you resolve problems you may encounter while setting up or using the projector.  
Power/ Status Light Messages  
Condition  
Power Indicator Status Indicator  
Steady orange  
Steady orange Blinking green (4 sec interval)  
Note  
Standby  
Normal  
–
–
ON-Timer setting  
On Timer is active  
Cooling down  
Blinking green  
Steady green  
Steady green  
Steady green  
–
Blinks green for 60 seconds  
Lamp in High-Bright mode  
Lamp in Eco mode  
–
–
–
Steady green  
Blinking green  
3 minutes after lamp is turned on in  
Eco mode  
Fixed at High-Bright mode. Lamp mode  
can be changed on the menu  
Lamp has reached its end of life  
(1500 hours or over)  
Steady green  
Steady red (High-Bright mode)/ Message appears on screen during 1500-  
Steady orange (Eco mode)  
1600 hours of lamp usage. The projector  
reaches its end of life. Please replace the  
lamp as soon as possible.  
Lamp life has reached its end of life  
(1600 hours or over)  
Steady orange Steady red  
The projector is in standby mode and can-  
not be turned on.  
Lamp cover, filter cover or lens holder  
error (3 locations)  
Steady orange Blinking red (1 sec interval)  
Steady orange Blinking red (4 sec interval)  
Steady orange Blinking red (8 sec interval)  
Steady orange Blinking red (12 sec interval)  
The projector is in standby mode and can-  
not be turned on.  
Temperature error  
The projector is in standby mode and can-  
not be turned on.  
Fan error  
The projector is in standby mode and can-  
not be turned on.  
Lamp error  
The projector is in standby mode and can-  
not be turned on.  
Lamp Light Messages  
Lamp Remaining Time  
Indicator  
100 – 50%  
Steady green  
Steady orange  
Steady red  
50 – 25%  
25 – 0%  
Common Problems & Solutions  
Problem  
Check These Items  
Does not turn on  
• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote  
control is on.  
• Ensure that the lamp cover is installed correctly. See page E-58 or E-60.  
• Check to see if the projector has overheated or the lamp usage exceeds 1600 hours (2100 hours in Eco  
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is particu-  
larly warm, move the projector to a cooler location.  
No picture  
•
Use the menu to select your source (Video1/2, S-Video, RGB1/2, DVI (digital/analog) or PC Card Viewer). See page E-40.  
• Ensure your cables are connected properly.  
• Use menus to adjust the brightness and contrast. See page E-41.  
• Remove the lens hood cap.  
• Reset the settings or adjustments to factory preset levels using the Factory Default on the Image Options  
Menu in Advanced menu. See page E-44.  
Image isn’t square to the  
screen  
• Reposition the projector to improve its angle to the screen. See page E-22.  
• Use the Keystone to correct the trapezoid distortion. See page E-22 or 42.  
Picture is blurred  
• Adjust the focus. See page E-21.  
• Reposition the projector to improve its angle to the screen. See page E-22.  
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See  
page E-12.  
Image is scrolling vertically,  
horizontally or both  
• Use menus or a source button on the remote control or the cabinet to select the source you want to input.  
Remote control does not  
work  
• Install new batteries. See page E-10.  
• Make sure there are no obstacles between you and the projector.  
• Stand within 22 feet (7 m) of the projector. See page E-10.  
Status indicator is lit or blink-  
ing  
• See the Power/ Status Light messages above.  
Cross color in RGB mode  
• If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image with the Position and Clock  
Adjust on the Advanced Options Menu. See page E-43.  
E – 62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ⅵ Selecting a new signal that is close to one of the listed signals in horizontal and vertical frequency may not display the image correctly because  
the new signal is considered as one of the registered signals listed in the Entry List. (In this case the Auto Adjust feature may not work correctly.)  
To use both signals, use different input terminal (RGB 1 or RGB 2) respectively, or assign specific remote keys for signals.  
1. Cut an existing signal from the Entry List.  
1) Select another signal other than the one currently projected because the currently projected signal cannot be cut.  
2) Press the ENTRY LIST button on the supplied remote control.  
3) After selecting the existing signal, press and hold down the CTL button and then the ENTER button simultaneously on the remote control. The Entry Edit  
Command window will appear. Select "Cut" and press the ENTER button.  
The selected signal will be deleted from the Entry List. (The signal data is stored in the clipboard.)  
2. Select the new signal and enter it in the Entry List.  
Press and hold down the CTL button and then press the ENTRY LIST button simultaneously on the supplied remote control to enter the signal in  
the Entry List.  
3. Paste the signal data that was cut and placed in the clipboard in Step 1.  
1) Select a vacant line in the Entry List.  
2) Press and hold down the CTL and then ENTER buttons simultaneously to display the Entry Edit Command window.  
3) Select "Paste" and press the ENTER button on the remote control to add the signal to the Entry List.  
4. Assign the listed signals for direct keys respectively.  
1) Select the one signal in the Entry List, and press and hold down the CTL and the ENTER buttons simultaneously on the remote control to display the Entry Edit  
Command window.  
2) Select "Edit" and then press the ENTER button to display the Entry Edit screen  
3) Select "Direct Key" and press the ENTER button to display the Direct Key screen.  
4) Assign the signals for direct keys.  
NOTE: Be sure not to disconnect the power cable while you are performing step 1 to 3. Failure to do so will delete the signal data stored in the clipboard. See also  
pages E-40 and E-41 for Entry List.  
When using the PC Card Viewer function  
Condition  
Status  
No picture  
• Is “PC Card Viewer” selected from the Source menu?  
• Is the PC card seated in the PC CARD slot completely?  
• Are slide data stored in the PC card?  
• Have the contents of the PC card been destroyed?  
Part of a slide is not displayed • While an image with over 1024
ן
768 dots is projected, several lines of information will be lost. Use the  
supplied software change the image to 1024
ן
768 dots in size.  
Contents of PC Card are • Use a computer, etc., to repair the data.  
damaged  
For more information contact your dealer.  
E – 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. SPECIFICATIONS  
This section provides technical information about the GT1150 Projector’s performance.  
Model Number  
GT1150  
Optical  
LCD Panel  
1.3" p-Si TFT active-matrix with Micro Lens Array, 1024
ן
768 native resolution up to 1600
ן
1200 with Advanced  
AccuBlend Technology  
Lamp  
250 W NSH lamp  
Lamp Life  
Eco-mode 2000 hours/High-Bright mode 1500 hours  
The lamp, under normal operating conditions, is warranted for 1500 hours of operation time within 6 months.  
Motorized zoom (except GT10RL lens) and Motorized focus  
GT19ZL : F2.0-2.5 f=48.9-63.7mm  
Lens Options  
GT13ZL : F2.3-2.8 f=34.5-42.5mm  
GT34ZL : F2.5-3.4 f=92.4-140.6mm  
GT10RL : F2.3 f=27mm  
Lens Shift  
Vertical +/- 0.5V  
(GT19ZL and GT34ZL)  
Image Size  
Horizontal +/- 0.25H  
GT19ZL/GT13ZL/GT10RL: 40 - 300 inches (1016 - 7620 mm) diagonal  
GT34ZL : 80-500 inches (2032-12700 mm) diagonal  
GT19ZL lens : 4.8 - 48.0 ft (1.5 - 14.6 m)  
Projection Distance  
GT10RL lens : 2.7-20.0 ft (0.8m-6.1m )  
GT13ZL lens : 3.5-32.0 ft (1.1m-9.8m )  
GT34ZL lens : 18.1-173.2 ft (5.5m-52.8m )  
GT19ZL: -9.0 degree (tele) / 11.7 degree (wide)  
GT13ZL: -13.3 degree (tele) / 16.4 degree (wide)  
Projection Angle  
GT34ZL: -4.0 degree (tele) / 6.2 degree (wide)  
Electrical  
Input Connections  
RGB/YCr/Cb/H(HV)V 5 BNC
ן
1, RCA (L/MONO, R)
ן
1  
RGB  
D-Sub 15 pin
ן
1, RCA (L/MONO, R)
ן
1  
DVI (Max resolution : XGA) x 1, RCA (L/MONO, R)
ן
1  
DVI also accepts analog signal  
BNC
ן
1, RCA
ן
1, RCA (L/MONO, R)
ן
1  
Mini DIN 4
ן
1, RCA (L/MONO, R)
ן
1  
Slot
ן
1  
RGB digital  
Video  
S-Video  
PC Card  
Output Connections  
Other Input/Output  
RGB  
D-Sub 15 pin
ן
1, RCA (L/MONO, R)
ן
1  
Stereo mini jack ;IN x 1; OUT
ן
1  
D-Sub 9 pin; IN
ן
1;OUT
ן
1  
Remote Control  
PC Control  
SW Control  
SC. TRIGGER  
D-Sub 15
ן
1  
Stereo mini jack
ן
1  
Input Compatibility  
NTSC / PAL / PAL60 / SECAM / NTSC4.43, YCbCr Component, HDTV-1080I, 720p, 480p,  
480I, VGA, SVGA, XGA, SXGA / UXGA (with AccuBlend)  
Horizontal Frequency : 15 - 100 kHz (RGB : 24 kHz or over)  
Vertical Frequency : 48 - 120 Hz  
Sychronization  
Range  
Video Bandwidth  
Color Reproduction  
Horizontal Resolution  
RGB: 100 MHz  
Full color, 16.7 million colors simultaneously  
550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr  
350 TV lines : SECAM  
RGB: 1024 dots horizontal, 768 dots vertical  
5W
ן
2  
Built-in Speakers  
Power Requirement  
100 - 120VAC / 200 - 240 VAC, 50 / 60 Hz  
Input Current  
3.9 A (100 - 120 VAC) / 1.9A (200 - 240 VAC)  
E – 64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mechanical  
Dimensions  
16.5" (W)
ן
4.7" (H)
ן
19.4" (D) / 419 mm (W)
ן
195 mm (H)
ן
494 mm (D) (not including feet)  
22.1 lbs / 10.0 kg (not including lens)  
Net Weight  
Environment  
Operational Temperatures: 32˚ - 104˚F (0˚ to 40˚C), 20 - 80% humidity  
Storage Temperatures: 14˚ - 122˚F (-10˚ to 50˚C), 20 - 80% humidity  
UL Approved (UL 1950, CSA 950)  
Regulations  
Meets DOC Canada Class B requirements  
Meets FCC Class B requirements  
Meets AS/NZS3548 Class B  
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)  
Meets Low Voltage Directive (EN60950, TUV GS Approved)  
LCD panels are inherently susceptible to bad pixels. The LCD panel may have pixel failures at the rate of 0.01% or less.  
We provide information about our projectors through the World Wide Web at http://www.nec-pj.com/  
The specifications are subject to change without notice.  
E – 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cabinet Dimensions  
P O W E R  
S T A T U S  
L A M P  
S / T A N O D N B Y  
D O W N  
Z O O M  
F O C U S  
A D J U S T  
A U T O  
L E N S S H I F T  
L E F T  
S E L E C T  
R I G H T  
U P  
S O U R C E  
7.7" (195)  
8.3" (210)  
16.5" (419)  
Lens center  
DVI  
L/MONO  
L/MONO  
RGB  
R
R
IN  
PC CONTROL  
OUT  
IN  
MONITOR OUT  
2
REMOTE  
2
Lens center  
OUT  
RGB1  
R/Cr  
G/Y  
B/Cb  
V
REMOTE  
1
SC, TRIGGER  
VIDEO  
1
H/HV  
L/MONO  
R
R
VIDEO  
2
AC IN  
L/MONO  
L/MONO  
R
-
S
VIDEO  
AUDIO OUT  
Unit = inch (mm)  
Optional Accessories  
Lens  
Optional lens (Fixed short throw: 1.0)  
Optional lens (Zoom: 1.3 – 1.6)  
Optional lens (Zoom: 1.8 – 2.4)  
Optional lens (Zoom: 3.4 – 5.2)  
Replacement lamp  
GT10RL  
GT13ZL  
GT19ZL  
GT34ZL  
GT50LP  
Lamp  
Ceiling Mount  
Kit for ceiling mount installation  
GT50CM  
GT50LAN  
PR50KIT  
Expansion module LAN module  
Remote Control Presentation remote control kit  
E – 66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D-Sub Pin Assignments  
Mini D-Sub 15 Pin Connector (RGB2)  
Signal Level  
Video signal : 0.7Vp-p (Analog)  
Sync signal : TTL level  
5
4
3
2
1
10  
9
8
7
6
15 14 13 12 11  
Pin No. RGB Signal (Analog)  
YCbCr Signal  
Video / S-Video  
1
2
Red  
Cr  
Composite video  
Green or Sync on Green  
Blue  
Y
Y
C
3
Cb  
4
Ground  
5
Ground  
6
Red Ground  
Cr Ground  
Y Ground  
Cb Ground  
Composite Ground  
Y Ground  
7
Green Ground  
Blue Ground  
8
C Ground  
9
No Connection  
Sync Signal Ground  
Ground  
10  
11  
12  
13  
14  
15  
Bi-directional DATA (SDA)  
Horizontal Sync or Composite Sync  
Vertical Sync  
Data Clock  
E – 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Menu Items Available in Link Mode  
See the table below for available functions in the analog link mode.  
Each letter used in the table below indicates the following:  
Master projector  
valid  
Slave projector  
linked  
L
N
M
I
invalid  
valid  
adjustable independently  
invalid  
invalid  
adjustable independently  
NOTE: The DVI connector does not support digital signal in the Link Mode.  
Function  
Link mode  
Menu  
Source Select  
Picture  
All (except PC Card Viewer, which is invalid in Link mode)  
All  
L
L
Volume  
L
Image Options  
Keystone  
N
Color Temperature  
Lamp Mode  
L
N
Gamma Correction  
L
Advanced Options  
Aspect Ratio  
Noise Reduction  
Color Matrix  
White Balance  
Switcher Gain  
Position  
L
N
N
L
N
N
Overscan  
L
Clock  
N
Resolution  
L
Video Filter  
Clamp Timing  
Y/C Delay  
L
N
N
YTR Adjustment  
CTR Adjustment  
HD Delay  
N
N
N
Factory Default  
Timer  
Menu  
N
L
M
Projector Options  
Setup  
N
Link Mode  
Switcher Control  
LAN Mode  
Capture  
M
N
N
N
Tools  
PC Card Files  
N
Help  
M
Test Pattern  
LENS SHIFT  
N
I
Direct Button  
Projector  
Remote control  
Projector  
Remote control  
Projector  
N
I
I
I
FOUCUS  
ZOOM  
Remote control  
Projector  
Remote control  
Projector  
Remote control  
Remote control  
I
MENU  
L (*1)  
L (*1)  
L (*2)  
L (*2)  
L (*2)  
L (*1)  
L (*1)  
L (*1)  
L (*1)  
L (*1)  
L (*1)  
L (*1)  
L (*1)  
N
POWER  
POWER ON  
POWER OFF  
INPUT (Alphanumeric) Remote control  
MUTE(PICTURE)  
MUTE(OSD)  
MUTE(SOUND)  
VOLUME  
Remote control  
Remote control  
Remote control  
Up/Down on projector  
Bar display  
No bar display  
Bar display  
Up/Down on remote control  
No bar display  
KEYSTONE  
AUTO  
Remote control KEYSTONE  
Projector  
N
Remote control  
Projector  
Remote control  
N
L (*1)  
N
SOURCE  
TEST  
*1 Each adjustment is not possible on the slave projector in the link mode.  
*2 Each adjustment is possible on the slave projector in the link mode.  
E – 68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timing Chart  
Y / N Signal  
Resolution  
( Dots )  
Frequency H. Refresh Rate  
Dot Clock  
( MHz )  
( kHz )  
( Hz )  
Y
Y
NTSC  
PAL  
640 
ן
 480  
768 
ן
 576  
768 
ן
 576  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
640 
ן
 480  
720 
ן
 350  
720 
ן
 400  
720 
ן
 350  
720 
ן
 400  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
800 
ן
 600  
832 
ן
 624  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1024 
ן
 768  
1152 
ן
 864  
1152 
ן
 870  
1152 
ן
 900  
1152 
ן
 900  
1280 
ן
 960  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
1280 
ן
 1024  
15.734  
15.625  
15.625  
31.47  
31.47  
31.47  
34.97  
35  
60  
-
50  
-
Y
Y
SECAM  
VESA  
IBM  
50  
59.94  
60  
-
25.175  
25.175  
25.175  
31.334  
30.24  
31.5  
31.5  
31.49  
36  
Y
Y
Y
MAC  
MAC  
MAC  
VESA  
VESA  
IBM  
60  
66.67  
66.67  
72.81  
75  
Y
Y
Y
37.86  
37.5  
Y
39.375  
43.269  
31.469  
37.927  
39.44  
39.44  
35.16  
37.879  
48.077  
46.88  
53.674  
49.725  
35.5  
75  
Y
Y
VESA  
IBM  
85.01  
70.09  
85.04  
87.85  
87.85  
56.25  
60.32  
72.19  
75  
28.322  
40  
Y
VESA  
IBM  
IBM  
Y
Y
35.5  
35.5  
36  
Y
VESA  
VESA  
VESA  
VESA  
VESA  
MAC  
VESA  
VESA  
VESA  
IBM  
Y
Y
40  
50  
Y
49.5  
56.25  
57.283  
44.9  
65  
Y
85.06  
74.55  
43 Interlaced  
60  
70.07  
72.03  
74.93  
75.03  
85  
#Y  
#Y  
#Y  
#Y  
#Y  
#Y  
#Y  
#Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
##Y  
48.363  
57.476  
58.131  
60.241  
60.023  
68.677  
67.5  
68.681  
61.796  
71.736  
60  
75  
79  
MAC  
VESA  
VESA  
VESA  
MAC  
SUN  
80  
78.75  
94.5  
108  
75  
75.6  
100  
65.95  
76.05  
60  
92.94  
105.6  
108  
SGI  
VESA  
SGI  
63.9  
60  
107.35  
108  
107  
VESA  
MAC  
MAC  
HP  
64.286  
64.31  
65.2  
60.02  
60.38  
69.82  
72.01  
76.11  
75.03  
85.02  
60 Interlace  
60 Progressive  
118.5  
135  
135  
78.125  
81.13  
79.976  
91.146  
33.75  
45  
SUN  
VESA  
VESA  
135  
157.5  
74.25  
74.25  
HDTV (1080i)(1125i) 1920 
ן
 1080  
HDTV (720p)(750p) 1280 
ן
 720  
SDTV (480p)(525p)  
SDTV (480i)(525i)  
VESA  
–
–
31.47  
15.73  
75.0  
59.94 Progressive 27  
59.9 Interlace  
–
1600 
ן
 1200  
1600 
ן
 1200  
1600 
ן
 1200  
1600 
ן
 1200  
60  
65  
70  
75  
162  
175.5  
189  
202.5  
VESA  
VESA  
81.3  
87.5  
VESA  
93.75  
##Y: Images in above flagged with ## and Y are compressed with Advanced AccuBlend.  
NOTE1: Some composite sync signals may not be displayed correctly.  
NOTE2: Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC.  
Refer to Display Properties help section of your PC for procedures.  
NOTE3: UXGA can be supported for separate sync signal only.  
E – 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PC Control Codes  
Cable Connection  
Communication Protocol  
Function  
Code Data  
Baud rate:  
Data length:  
Parity:  
Stop bit:  
X on/off:  
38400 bps  
8 bits  
No parity  
One bit  
None  
POWER ON  
02H 00H 00H 00H 00H 02H  
POWER OFF  
02H 01H 00H 00H 00H 03H  
INPUT SELECT RGB 1  
INPUT SELECT RGB 2  
INPUT SELECT VIDEO 1  
INPUT SELECT VIDEO 2  
INPUT SELECT S-VIDEO  
02H 03H 00H 00H 02H 01H 01H 09H  
02H 03H 00H 00H 02H 01H 02H 0AH  
02H 03H 00H 00H 02H 01H 06H 0EH  
02H 03H 00H 00H 02H 01H 07H 0FH  
02H 03H 00H 00H 02H 01H 0BH 13H  
Communications  
procedure:  
Full duplex  
OPTION (D-SUB 9P)  
To TxD of PC  
To RxD of PC  
To GND of PC  
INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H  
INPUT SELECT DVI (ANALOG)02H 03H 00H 00H 02H 01H 03H 0BH  
INPUT SELECT PC CARD VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H  
PICTURE MUTE ON  
PICTURE MUTE OFF  
SOUND MUTE ON  
02H 10H 00H 00H 00H 12H  
02H 11H 00H 00H 00H 13H  
02H 12H 00H 00H 00H 14H  
02H 13H 00H 00H 00H 15H  
02H 14H 00H 00H 00H 16H  
02H 15H 00H 00H 00H 17H  
SOUND MUTE OFF  
ON SCREEN MUTE ON  
ON SCREEN MUTE OFF  
1
2
3
4
5
6
7
8
9
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.  
To RTS of PC  
To CTS of PC  
NOTE: Pins 1, 4, 6 and 9 are used inside the projector.  
Gravity Stack  
Up to two units can be gravity stacked without external support. In some cases, however, two images will not align on the  
screen correctly. This will become more apparent when displaying small text and detailed graphics.  
1. Note : Gravity Stacking Two GT1150 Projectors  
The optional lenses for GT1150 have different geometrical distortions in wide zoom and tele. Select the best zoom position for  
stacking where the geometrical distortion is as small as possible. The recommended throw distances are as follows:  
Screen Size  
(Diagonal)  
Throw Distance  
GT13ZL  
GT19ZL  
GT34ZL  
m
feet  
5.7  
8.7  
11.6  
14.6  
17.5  
22.0  
29.3  
35.2  
44.1  
-
m
1.0  
1.6  
2.1  
2.7  
3.2  
4.0  
5.4  
6.4  
8.1  
-
feet  
3.4  
5.2  
7.0  
8.7  
10.5  
13.2  
17.6  
21.1  
26.4  
-
m
-
-
6.7  
feet  
-
-
40"  
60"  
80"  
1.7  
2.6  
3.5  
4.4  
5.3  
6.7  
8.9  
10.7  
13.4  
-
22.0  
27.5  
33.0  
41.3  
55.1  
66.1  
82.6  
96.4  
110.2  
124.0  
137.8  
100"  
120"  
150"  
200"  
240"  
300"  
350"  
400"  
450"  
500"  
8.4  
10.1  
12.6  
16.8  
20.2  
25.2  
29.4  
33.6  
37.8  
42.0  
-
-
-
-
-
-
-
-
-
-
-
-
• Lens position  
Horizontal lens position must be as close to the center of the lens opening as possible.  
2. Note: Gravity Stacking in link mode  
A distribution amplifier is recommended for Gravity stacking in link mode to distribute one input source to two projectors.  
3. Note: Gravity stacking in link mode without a distribution amplifier  
In this configuration, horizontal position of each projector will need to be adjusted before enabling Link mode.This adjustment will  
prevent image alignment.  
E – 70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in Japan  
7N8P0112  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Vacuum Cleaner S160 User Manual
Miller Electric Welder XLT 185 User Manual
NETGEAR Switch GS205 User Manual
NeumannBerlin Microphone TLM 103 User Manual
Nortel Networks IP Phone NN43114 100 User Manual
Nortel Networks Wireless Office Headset PO937240 02 User Manual
Olympus Camera Lens 261013 User Manual
Omega Smoke Alarm OS137 User Manual
Onkyo CD Player CR B8 User Manual
Panasonic Cordless Drill EY7880 User Manual