Return
to Menu
Part No. P0937240 02
Business Communications
Manager 2.5
Telephone Features
Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3
Contents
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5
Text conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Unified Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
Telephone types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Telephone installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Name a telephone or a line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Extension numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Line assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.4
Target line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Overflow call routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Telephone buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
One-line and two-line displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Buttons under the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Memory buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7
Program buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.7
Chapter 2
Answer calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ring types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Distinctive Line Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Call Ringing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.9
Call Answering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Line buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Information about a call on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Call Information for a specific call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 1
View Call Information before or after answering . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Change which call information appears first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Contents
Priority Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Answer calls at a prime telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.2
Central answering position (CAP) module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Customize your CAP module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 4
Release button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Pick up a call ringing at another telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Group Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Change a telephone’s pickup group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Trunk Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Answer buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Listen to a call as a group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cancel Group Listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Make a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Line pools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Use a line pool to make a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.1
Program a line pool feature code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. 2
Line buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Select how you dial your calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Standard dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.2
Automatic dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Pre-dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Priority Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Make a priority call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Turn on Ring Again . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cancel Ring Again . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Create a Conference Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Disconnect one party . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Separate holding of two calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.6
Put a conference on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Split a conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Leave a conference call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5
Autodial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Select a line for Autodial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Use intercom as the line for Autodial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Prevent Last Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Personal Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Saved Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Save a number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Prevent Saved Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 5
Handling calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Use Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Retrieve a held call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Listen on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Hold a call exclusively . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Call Queuing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.6
Transfer calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Transfer external calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Cancel a transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.7
Camp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Call Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Park a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Call Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Cancel Call Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Override Call Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Change the automatic Call Forward settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Call Forward on busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
DND on Busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Contents
Call Forward and voice mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Line Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5
Allow a telephone to redirect calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Turn on Line Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Cancel Line Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Communicating in the office. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Page Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Activate and deactivate the Page feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Create page zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Send a message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.1
Review your messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Reply to a message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Remove items from your message list using an analog telephone connected to an ASM
73
View messages you have sent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Make a Voice Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Mute Voice Call tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Cancel Voice Call Deny . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Track your incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Call Log options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7
Delete old log items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
View your Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Make a call using Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7
Create a password to your Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Delete an assigned password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. 0
Customize your telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Adjust the contrast on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.3
Change the language on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Adjust the Ring volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Button Inquiry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Programming feature codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Default button assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
T7316 Button mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
T7100 telephone button defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Move line buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Hunt Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Members of the group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Distribution mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Telephone features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Hunt Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Prevent calls from ringing at your telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Use Do Not Disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Cancel Do Not Disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Turn Privacy on or off for a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Contents
Make a call private . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Handsfree and Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.7
Make calls without lifting the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Change a handsfree call to a normal call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Handsfree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Change Handsfree for a telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Handsfree Answerback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Hearing aid compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Call Duration Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Accidental disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Disconnect supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Background Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Cancel Background Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
System features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
ISDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Name and number blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Ringing service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Routing service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Turning services on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Turn services on and off using feature codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Log password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Special telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Direct dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Hotline bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Control telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Set lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
9
Turn the auxiliary ringer on or off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Long Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Wait for Dial Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Pulse or tone dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Pulse dialing for a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Access your system from an external location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Direct Inward System Access (DISA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Class of Service (COS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Change your Class of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Maintain security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Remote access over the public network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Voice mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Call Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Cancel Call Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Automatic Call Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Automatic Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Hospitality Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Types of telephone set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Common set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Hospitality Services (HS) admin set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Alarm time (AL) feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Program the Alarm time feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Cancel an alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Turn off an Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Hospitality Services admin alarm feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Room occupancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Contents
Room condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Room condition from a room set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Hospitality passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Desk admin password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Room condition password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Portable telephone features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Directed Call Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Group Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Report and record alarm codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Test the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Test the telephone display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Test the telephone buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Test the telephone headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Test the telephone speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Test the power supply to a telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Feature Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Features sorted by activation code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures 11
Figures
Display buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Figures
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables 13
Tables
Telephone buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Tables
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Preface
This guide provides information about how to program a Business Communications Manager
telephone. This information includes items such as programming personal speed dials, transferring
a call, and using special features. Some of the features included in the Business Communications
Manager telephone system are:
•
•
•
•
•
conference calls
group listening
group pickup
directed pickup
call tracking
This guide is aimed at the day-to-day operators of the Business Communications Manager
telephone system.
Before you begin
Plan the programming changes you want to make before you begin. Record the changes so that
you have the information at hand. For example, before you program system speed dial numbers,
create a record so that you have all the numbers and codes available.
Programming applies to both North America and International telephones in your Business
Communications Manager system.
Emergency 911 Dialing
Emergency 911 Dialing is the capability to access a public emergency response system.
State and local requirements for support of Emergency 911 Dialing service by Customer Premises
Equipment vary. Ask your local telecommunications service provider about compliance with
applicable laws and regulations.
Emergency 911 Dialing may not apply to International systems.
Text conventions
This guide uses the following text conventions:
angle brackets < >
Indicate the generic title on the telephone display.
Example: When querying a feature button.
<Feature name>appears in angle brackets.
Bold
Indicates a programming level within the telephone menu.
Example: Terminal & Sets programming level.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Preface
ClearDisplay font
Indicates what appears on the telephone display.
Example: CALL.
italic text
Indicates new terms and book titles.
Example: Business Communications Manager Telephone
Feature Card.
Forward slash /
Separates names where two actions are assigned to one button.
Example: Run/Stop.
Acronyms
This guide uses the following acronyms:
AL
Alarm
ASM
ATA
BLF
BRI
Analog Station Module
Analog Terminal Adapter
Busy Lamp Field
Basic Rate Interface
CAP
CFB
CFAC
CFNA
CLID
COS
DID
DISA
DN
Central Answering Position
Call Forward on Busy
Call Forward All Calls
Call Forward No Answer
Calling Line Identification
Class of Service
Direct Inward Dial
Direct Inward System Access
Directory Number (Extension Number)
Do Not Disturb
DND
DLR
DRP
DRT
ERC
HS
Distinctive Line Ring
Distinctive Ring Pattern
Delayed Ring Transfer
Express Routing code
Hospitality Services
IP
Internet Protocol
ISDN
ISO
Integrated Services Digital Network
International Organization for Standardization
Private Branch Exchange
Primary Rate Interface
PBX
PRI
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface 17
RC
Room Condition
RJXX
Registered Jack XX (Where XX is used to denote numbers, for
example: 45 or 5.)
RO
Room Occupancy
SLR
URL
Selective Line Redirection
Uniform Resource Locator
Related publications
For more information about using Business Communications Manager 2.5, refer to the following
publications:
•
•
Business Communications Manager Installation and Maintenance Guide
Business Communications Manager Programming Operations Guide.
This document provides more information about using Unified Manager.
•
Business Communications Manager DECT Installation and Maintenance Guide
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Preface
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Chapter 1
Introduction
Your Business Communications Manager telephone system has many features that you can
customize to keep up with changes in your workplace.
Unified Manager
Unified Manager is the tool used to program settings for the system telephony features, and
settings for each telephone and external lines. Multiple levels of programming are accessible
through Unified Manager. You access the Business Communications Manager Unified Manager
from your web browser. For more information about navigation and making selections using
Unified Manager, see the Business Communications Manager Programming Operations Guide.
Telephone types
Figure 1 shows the three different Business Series Terminals, as well as the M7324 and M7324N
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Chapter 1 Introduction
Figure 1 T7100, T7208, T7316, M7324 and M7324N telephones
T7100
T7208
T7316
M7324
M7324N
Telephone installation
If you are connecting a Business Communications Manager telephone for the first time, refer to the
following illustrations and steps.
1
2
Disconnect the line cord from the wall socket before trying to carry out any work on the
telephone.
To remove any of the cords, press the release latch on the plug and carefully pull the plug from
the socket.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction 21
3
4
5
6
7
Connect the handset cord to the jack labelled with the telephone icon and route the cord as
shown.
If you are using a headset, route the cord along the channel in the base and connect the cord to
the telephone jack that is labelled with the headset icon.
Route the line cord through the support and connect the cord to the telephone jack that is
labelled with the jack icon.
Attach the support using either pair of slots; to raise the back of the telephone to its highest
position, use these slots.
When the above work is complete, plug the line cord back into its wall socket.
Figure 2 Installing a T7316 telephone (North America)
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction 23
Figure 4 Mounting a T7316 telephone without a stand on the wall
Name a telephone or a line
You can assign names to identify external lines, target lines, and your colleagues’ telephones.
During a call, the name (if programmed) appears on the telephone display instead of the external
line number or internal telephone number of the caller. You need to start a Unified Manager
session to program this feature. For more information about programming using Unified Manager,
see the Business Communications Manager Programming Operations Guide.
Telephone names and line names can contain both letters and numbers, but cannot be longer than
seven characters. You cannot use the # and * symbols.
Note: You can give the same name to a telephone and a line in your system. Use
initials, abbreviations, or even nicknames to give each telephone a unique name to
avoid confusion.
Extension numbers
Each telephone in the system has an extension number. The length of extension numbers in your
system can range from two to seven digits. All numbers in your system are the same length. Your
installer assigns the length of extension numbers, called the extension length. The default
extension length is three.
To find out your internal number, use the Button Inquiry feature (≤•‚) from an intercom
button. On the T7100 telephone, Button Inquiry shows your internal number followed by the
function assigned to the memory button.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Chapter 1 Introduction
Line assignment
You can assign any of the lines in your system to any of your telephones.Your installer assigns
lines to telephones. Assignments for lines are:
•
•
•
appear only
appear and ring
ring only
Lines assigned to a telephone automatically have a line button on that telephone, when a button is
available. The T7100 telephone has no line buttons.
Prime line
You can program your telephone to select an internal, or external line, or a line pool automatically
when you lift the handset. This is your prime line.
Private line
A private line is limited to a selected telephone. You can pick up calls put on hold, or not answered
on a private line, only at the prime telephone.
Target line
A target line routes a call directly to a selected telephone, or group of telephones. Target lines are
only for incoming calls. A single incoming line can provide connections to several different target
lines. Target lines allow each person or department in the office to have their own number without
having a separate external line for each number.
Overflow call routing
If a call comes in to a target line that is busy, the system routes the call to the prime telephone for
that target line. If there is no prime telephone assigned to the target line, or if you cannot direct a
call to a target line, the call goes to the prime telephone for the external line.
Overflow routing for incoming calls uses the routing service programmed by your installer.
Service must be active for overflow routing to operate. Overflow routing is not available in normal
service.
Note: When you make a call and the programmed route is busy, you hear the
expensive route warning tone and see a display indicating the use of an expensive
route. To avoid using the normal, expensive route, release your call.
Because overflow routing directs calls using different line pools, a call might be
affected by different line filters.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction 25
Telephone buttons
This guide shows the Business Series Terminals buttons. Table 1 shows which buttons to use on the
Table 1 Telephone buttons
M7100, M7208, M7310,
M7324
M7100N, M7208N,
M7310N, M7324N
Button Name
Feature
T7100, T7208, T7316
≤
Ä
©
©
ú
Ã
¨
ƒ
Handsfree
Mute
Bottom right-hand button
©
©
˙
©
Hold
≥
Volume Control
Release
√
®
√
®
You can enter ≤, Ä, or ƒ and the code to use a feature. For example: Press
≤·°⁄ to access your mailbox.
The T7100telephone works differently from other telephones on your system because it does not
have line buttons. Where other telephones can require that you select a line button to answer a call,
on the T7100 telephone you pick up the handset. Where other telephones require you to select a
line button to take a call off hold, you press ≥ on the T7100 telephone.
On T7100 telephones, you can answer a second call by pressing ≤. Your active call is put on
hold and you connect to the waiting call. You can have no more than two active calls at one time.
The T7100 telephone does not have a © button.
Table 2 Telephone button functions
1
Dial pad
Used for dialing numbers and for entering numbers and letters when
you are programming.
2
3
4
5
Display
Shows instructions for calling and programming.
The current use appears on the display above each button.
Dial a number or feature code stored on the button.
Display buttons
Memory buttons
Feature button
Allows you to enter a feature code while using or programming the
telephone.
6
7
Hold button
Puts an active call on hold.
Release button
Hangs up an active call or ends programming.
For more information about telephone buttons, refer to your Telephone User Card.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
26 Chapter 1 Introduction
One-line and two-line displays
The T7100 and T7208 telephones have a one-line display. The T7316 and M7324(N) telephones
have a second line on the display which shows the functions of the three buttons below it. Figure 5
Figure 5 Display buttons
Contrast level
DOWN UP
2
OK
Contrast level
DOWN UP
2
OK
Contrast level
DOWN UP
2
OK
Display buttons
Some display buttons, such as TRANSFR and ALL, are shortcuts that are only available on a two-line
display. Other display buttons, such as OK and SHOW, perform a function necessary to proceed. Table
3 shows display button functions and dial pad buttons on a one-line display telephone. See
Table 3 Substitutes for buttons on a one-line display telephone
Dial pad buttons on a T7100
Display buttons and T7208 telephones
OK
≥ or ú
QUIT
® or ¨
ADD
•
SHOW
£
CANCEL
VIEW
£
£
OVERRIDE
BKSP
£
√ or Ã
All examples in this guide show the two-line display.
Buttons under the display
The three display buttons are for telephone features. The programming session determines what
the display shows and what each button does. Some display instructions are OK, CHANGE or COPY. In
this guide, display button instructions appear underlined.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction 27
Memory buttons
You can use memory buttons as answer, autodial, line, and programmed feature buttons. Line,
intercom and answer buttons must have indicators. The T7316, T7208 and M7324(N) telephones
have memory buttons with indicators. The T7316 telephone also has memory buttons without
indicators. There is a single memory button, without an indicator, on the T7100 telephone.
Program buttons
Press the ≤ button on the telephone followed by an activation code for personal programming.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Chapter 1 Introduction
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Chapter 2
Answer calls
There are three indications of an incoming call:
•
ringing
a line button flashing
a message on the display
•
•
You do not always receive all three indications for any distinct call. For example, you can have a
line set up not to ring at your telephone. If so, you see only a flashing line button. There are many
possible combinations, depending on your system set up. For more information about the use of
Ring types
There are several different types of ring.
A double beep every ten seconds
A long single ring
A call is camped to your telephone.
There is an external call on the line for you.
A shorter double ring
There is an internal call on the line for you, or a call
is being transferred to you.
A brief single ring
A call arriving on an external line is redirected to a
telephone outside of your system. You cannot
answer this call.
Three beeps descending in tone
You are receiving a priority call.
Distinctive Line Ring
There are four Distinctive Ring patterns (DRP) for incoming calls.
DRP 4
DRP 3
DRP 2
DRP 1
Highest priority
2nd highest priority
3rd highest priority
Lowest priority
Call Ringing
When more than one call rings at a telephone, highest proprity DRP rings through first.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Chapter 2 Answer calls
Call Answering
When more than one call rings at a telephone, the user lifts the handset and automatically answers
the call with the highest priority.
Note: External calls have a higher priority than internal calls.
You cannot press ≤•fl to change the ring type on a telephone when
the Distinctive Line Ring feature is in service.
For more information about the Distinctive Line Ring feature, refer to the Business
Communications Manager Programming Operations Guide.
Line buttons
For each line assigned to your telephone, you have one line button. Press the flashing line button to
select the line you want to answer. Having several line buttons gives you immediate access to more
than one line.
The T7100 telephone has two intercom paths, instead of line buttons, to answer calls. You can
assign two lines to each T7100 telephone. You can press ≥ to switch between two calls, one
active and one on hold.
What line indicators mean
Ω
Ω
Flashing on and off for equal
lengths of time
There is an incoming call on the line.
You have placed a call on hold.
Flashing on and off more
quickly
Ω
Ω
Flashing on for longer than off
On, but not flashing
A person has put a call on hold on that line.
You are connected to the call on that line or the
line is in use.
Off
The line is free.
Information about a call on the display
If you subscribe to Call Display services from your local telephone company, one line of
information about an external caller appears on the display after you answer a call. Depending on
the setting and the external information available, either the caller name or telephone number
appears on the display. When you transfer an external call to another telephone in your system, the
same information appears on the recipient’s telephone display.
Depending on the services you subscribe to, Call Display information can contain up to three
parts:
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Answer calls 31
•
•
•
the name of the caller
the number of the caller
the name of the line in your system that the call is on
For each telephone, you can determine which information appears on the display first.
Call Display information becomes available between the first and second ring of an incoming call.
If you answer before the Call Display information appears on your display, press ≤°⁄⁄ to
Call Information for a specific call
Call Information allows you to see information about incoming calls. This information is more
detailed than the Call Display information you can receive automatically. For external calls, you
can see the caller name, telephone number, and the line name. For an internal call, you can see the
caller name and the internal number. You can see information for ringing, answered, or held calls.
Call Log shows the same information as Call Information, with the date and time of the call, and
the number of times the caller called.
View Call Information before or after answering
To find out who is calling or to view information about your current call:
1
2
Press ≤°⁄⁄.
Press £ or VIEW for more information about an external call.
Call Display information appears between the first and second ring of an incoming call. If you
answer before the Call Display information appears on your display, and you press ≤°⁄⁄,
you see only the line number or line name.
View Call Information for a call on hold
1
2
3
Press ≤°⁄⁄. The display shows Ω Select a call.
Select the line on hold. Information about the call appears on the display.
Press £ or VIEW to display more information about an external call.
Note: If your telephone automatically shows Call Display information
for a call, press ≤°⁄⁄ before you press £ or VIEW for more
information about the call.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Chapter 2 Answer calls
Make Call Display information appear automatically at a telephone
Each telephone that rings for an external line can show Call Display information for that line. After
answering a call, Call Display information appears on the display of the telephone that answered
the call. Your installer or customer service representative can program telephones to have
automatic Call Display.
Change which call information appears first
If the information is not available from your telephone company, you can see Unknown name or
Unknown number on the display. If the caller blocks that information you can see Private name or
Private number on the display.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Priority Call
If you receive a priority call and your telephone has no free internal line buttons, you cannot
transfer the priority call, you must accept or release it.
Answer calls at a prime telephone
The prime telephone is normally the attendant’s telephone. The installer or customer service
representative programs a prime telephone for a line. Calls not answered at their normal
destinations transfer to the prime telephone. Business Communications Manager allows for a
prime telephone for each line if needed. The prime telephone display gives information about the
call, as in the following examples.
DND from 221
The person at telephone 221 has forwarded a call to you using
Do Not Disturb.
DND transfer
The system has transferred a call to you from a telephone with
Do Not Disturb turned on.
DRT Line001
No person answered this call so the system transferred it to you.
Line061 callback
A person camped, parked or transferred a call on line 061, but
no one has answered the call. Press CALLBCK or the line button to
CALLBCK
connect to the call.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Answer calls 33
Line061 to prime
Line002>Line052
There is no telephone that can receive a call on line 061 so the
system has transferred it to you.
The call coming in on line 002 for target line 052 has come to
you because Line 052 is busy.
Central answering position (CAP) module
A CAP module is an add-on device that provides 48 additional memory or line buttons. You can
connect one or two CAP modules to the telephone to increase the number of lines it can handle. A
CAP can monitor system telephone status, answer external calls on up to 120 lines, and send up to
30 messages to other system telephones.
A central answering position (CAP) is an M7324 or M7324N telephone and a CAP module(s) that
your installer or customer service representative programmed as a CAP. You can have up to five
telephones programmed as CAPs connected to Business Communications Manager. The CAP is
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
34 Chapter 2 Answer calls
Figure 6 CAP module with M7324 and M7324N telephones
M7324 telephone
CAP Module
M7324N telephone
CAPN Module
Customize your CAP module
When a CAP module is first plugged into your telephone, some of the module buttons are
automatically programmed to dial an internal number. You can program any of the buttons on your
CAP module that do not select lines to dial internal or external numbers automatically.
If your installer has programmed the CAP module for your system, you can move external lines to
programming memory buttons. You cannot assign any buttons on a CAP module as answer
buttons.
Monitor telephones with the CAP module
The indicators Ω next to internal autodial buttons on your CAP module show the status of the
telephones in your system.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Answer calls 35
The indicator is on when the telephone has:
•
•
an active call
Do Not Disturb turned on
The indicator is off when a telephone has:
•
•
no active call
a call on hold and no other active call
Release button
Press ®to end a call.You do not have to put the handset down. ® also ends feature
programming.
While you are on a call, do not press ® to end a feature you are using. If you do, you disconnect
the call. Use ≤ instead.
Pick up a call ringing at another telephone
You can answer a call ringing at another telephone by using Directed Pickup or Group Pickup.
Directed Pickup
You can answer any telephone that is ringing in your system.
1
2
Press ≤ ‡fl.
Enter the internal number of the ringing telephone. You cannot use Call Pickup to answer
private lines.
Answer the telephone that has a flashing indicator for the call, or use Trunk Answer.You can
answer a call that is transferred to an intercom button on another telephone. When the auxiliary
ringer is ringing, but the call is not ringing at a telephone, you cannot answer the call using
Directed Pickup.
Note: Directed Pickup can retrieve calls that are ringing on an Answer
extension. Although you can enter the extension number of the telephone
you hear ringing, it is possible the calls you are answering are from
another telephone.
Group Pickup
Your system can support nine pickup groups. As a member of a pickup group, you can pick up a
call that is ringing at any telephone in your pickup group.
Press ≤‡fi to pick up.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Chapter 2 Answer calls
You cannot use Group Pickup to retrieve a camped call.
With more than one incoming call at a telephone in a pickup group, a call ringing on an external
line is answered first, followed by calls on the prime line, and last, calls on intercom lines.
Change a telephone’s pickup group
To place and retrieve telephones in and out of pickup groups, you need to start a Unified Manager
session to program the feature. For more information about programming using Unified Manager,
see the Business Communications Manager Programming Operations Guide.
Already joined
You are connected to the telephone that made the call you are
trying to pick up. This display appears if you are on a call to a
colleague, your colleague dials the number of a telephone in
your pickup group, and you try to pick up that call.
Pickup denied
There is no call to pick up, or the call has been answered
or
you have tried to pick up a call on a person’s private line.
Pickup:
Enter the internal number of the telephone that is ringing. (You
can use an internal autodial button to do this.)
If you decide not to answer a ringing call after you have
activated Directed Pickup, press ≤.
Trunk Answer
The Trunk Answer feature allows you to answer a ringing call in any area in the system from any
telephone in the system. The line you are answering does not have to appear or ring at the
telephone you are using.
Trunk Answer works only with calls that are ringing on lines for which a Ringing Service schedule
is active, and if your installer or customer service representative enabled Trunk Answer. If there is
more than one incoming call on lines in a Ringing Service, the Trunk Answer feature picks up the
external call that has been ringing the longest.
Line denied
You have tried to pick up a call on a person’s private line.
Pickup denied
The call that is ringing is on a line that is not in a Ringing
Service.
Answer buttons
You can use an answer button to monitor calls on another person’s telephone. All calls to the
monitored telephone appear on the Answer button.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Answer calls 37
Answer buttons help attendants to monitor incoming calls for one or several other people. For
example, an attendant can have line appearances for three different managers on the answer
buttons of the telephone.
When an attendant answers a call for manager A the appearance stops at that manager’s set. This
flexibility allows for another (simultaneous) call to come in on the same line. The same is true for
manager B and manager C. When incoming call traffic increases, the calls can route to a Hunt
The Answer button setting in Feature settings programming allows you to determine what types of
calls ring at the telephone.Your options are:
•
•
•
basic
enhanced
extended
For more information about programming Answer buttons, see the Business Communications
Manager Programming Operations Guide.
T7100 telephones have no Answer buttons assigned to monitor other sets, but you can monitor
them.
You cannot make calls using Answer buttons.
If two or more calls are ringing at a person’s telephone, the first call appears on the attendant’s
Answer button. Any additional calls appear on intercom buttons, if they are available.
Note: More than one attendant can have an Answer button for a single
telephone, allowing two or more attendants to handle calls for a busy
person.
Each telephone can handle calls for up to eight other people using a
separate Answer button for each person.
Listen to a call as a group
To allow people in your office to listen in on a call using Group Listening, press ≤°‚¤.
You hear the caller’s voice through your telephone’s speaker. Continue to speak to the caller
through the telephone handset. Your telephone’s microphone is off, so the caller does not hear
people in your office.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
38 Chapter 2 Answer calls
Cancel Group Listening
Group Listening cancels automatically when you hang up, or when you press ≤£°‚¤
Note: Keep the handset away from the speaker, or you can hear feedback.
The higher the volume, the more the feedback. Press ® to prevent
feedback when hanging up.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Chapter 3
Make a call
The following are different ways to make a call, depending on the programming and the type of
call:
•
Pick up the handset and dial. Business Communications Manager supports three methods of
•
•
•
Pick up the handset, press a line button, and dial (if the call is not on your prime line).
Press a line or intercom button, then press the handsfree button and dial (to talk without the
handset. The speaker is active and the microphone is muted until you select the handsfree
button or pick up the handset).
•
•
Press a line or intercom button and dial (to talk without the handset and if Automatic
Handsfree is programmed on your telephone).
221 busy
The telephone you have called has no internal lines available.
Press LATER to use the Ring Again or Message features or press
PRIORITY to make a priority call.
PRIORITY
LATER
9__
You are dialing using Pre-dial.To erase an incorrect digit, press
the left end of √ or BKSP. When the number is
complete, select a line or lift the handset.
QUIT
BKSP
95551234
TRANSFR
This prompt remains on your display while you are on a call you
have dialed. To transfer the call, press TRANSFR.
Already joined
Your telephone is connected to the telephone you are trying to
call. Check your active line buttons, and return to that call.
Calling 221
PRIORITY
Wait for the telephone to be answered. If no one answers, press
to make a priority call.
LATER
Can't ring again
You cannot use Ring Again on your current call.You can use
Ring Again while you have a busy signal on an internal call or
line pool request or while an internal call is ringing.
Do not disturb
The telephone you are calling has Do Not Disturb turned on.
Press LATER to use the Ring Again or Messages features, or press
PRIORITY to make a priority call.
PRIORITY
LATER
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Chapter 3 Make a call
Expensive route
You have dialed a number, but the least expensive route
programmed for the system is busy. Unless you release the call,
the number goes through on a more expensive route.
Hidden number
Line denied
The last number you dialed or the number you saved for Saved
Number Redial was a speed dial number that displayed a name
instead of the number.You dialed the number correctly, but it is
not visible.
You have tried to use another person’s private line.
Line061
TRANSFR
Enter the digits of the number you want to dial.
No last number
No line selected
Not in service
You have not dialed an external telephone number since the last
power interruption or system reset.
Either you have no prime line or your prime line is busy. Select a
line manually before dialing.
You have entered the number of a telephone that is not in
service.
On another call
LATER
The telephone you have called is on another call. Press LATER to
use the Ring Again or Message features.
Restricted call
System programming has a restriction configured for the call
you are trying to make. A possible reason is time-of-day
restrictions for some calls.
Ring Again?
Press YES to use Ring Again. Press NO to send a message. See
YES
NO
EXIT
Select a line
Either you have no prime line, or the prime line is in use, or the
line programmed for an autodial number, speed dial number, or
Hotline is in use. Select a line and dial again.
Send message?
Press YES to send a message. See Messages.
YES
NO
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Make a call 41
Denied in Admin
The Last Number is not allowed.
Line pools
A line pool allows each telephone access to external lines from a group (or pool) of external lines.
To access a line pool:
•
•
press an intercom button and enter a line pool access code
press a memory button programmed with the line pool feature code and a line pool access code
A line pool is a group of external lines shared by many telephones. You can use a line in a line pool
to make an external call.
The system can support 15 line pools plus six PRI pools, and depending on system programming,
a telephone can access any number of these line pools.
A line pool access code is the number you dial to get a line pool. The access code can be up to four
digits long. You can have several different line pools for your system, each one giving you access
to a different set of external lines. Line pools is one way of sharing lines across telephones in a
system.
Your installer programs the access codes for line pools and gives each telephone access to a line
pool.
Everyone in the office can have a list of the access codes for line pools their telephones can use.
Use a line pool to make a call
1
2
Press ≤fl›.
Enter a line pool access code.
If you have a free internal line, you can make a call using a line pool without entering the feature
code first.
1
2
Select an internal line (intercom).
Dial the line pool access code.
Note: If no lines are available in the line pool, you can use Ring Again at the busy
tone. The system will inform you when a line in the line pool becomes available.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
42 Chapter 3 Make a call
Program a line pool feature code
When you program a button with the line pool feature code, you must enter a line pool access code
after the feature code. The programmed line pool button accesses a specific line pool, not the line
If you program a button with an indicator to access a line pool, the indicator for the line pool
button turns on when all the lines in a line pool are busy. The indicator turns off when a line
becomes available.
Line buttons
There is one line button for each line assigned to your telephone. Press the line button to select the
line you want to answer or use to make a call. As you have several line buttons, you can access
more than one line.
The T7100 telephone has two intercom paths, instead of line buttons, to answer and make calls. A
T7100 can have two lines. You can press ≥ to switch between two calls, one active and one on
hold.
Select how you dial your calls
To select a dialing mode:
1
2
3
Press ≤•°¤.
Press £ or NEXT until the dialing mode you want appears.
Press ≤ or OK to select the dialing mode.
You cannot program the dialing modes feature code on a memory button.
Standard dial
Standard dial allows you to make a call by selecting a line and dialing the number. If you have a
prime line, it is selected automatically when you lift the handset or press the handsfree button.
You cannot use Standard dial on a T7100 telephone unless you pick up the handset first. If you
have a T7100 telephone, use the Automatic dial or Pre-dial feature for on-hook dialing.
Automatic dial
Automatic dial allows you to dial a number without selecting a line. Your prime line is selected
when you start dialing a number. Automatic dial does not work if your telephone has no prime line
or when your prime line is in use.
Telephones connected to an Analog Terminal Adaptor (ATA2) or an Analog Station Module
(ASM) cannot use Automatic dial.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Make a call 43
Pre-dial
Pre-dial allows you to enter a telephone number, check it, then change it before making the call.
The call does not dial until you select a line or line pool, or pick up the handset.You can pre-dial
both external and internal numbers. You must, however, select the correct type of line (external or
internal) for the type of number you have entered.
Note: If your telephone starts ringing while you are pre-dialing a number, you
can stop the ringing by turning on Do Not Disturb (≤°fi). Do Not Disturb
entered while dialing does not affect the numbers you are entering.
You cannot pre-dial a telephone number if all the lines on your telephone are busy.
Receive a busy signal on an internal call
When the internal number you dialed is busy there are three possibilities:
•
•
•
Priority Call
Ring Again
Message
Priority Call
If you get a busy signal or a Do Not Disturb message when you call someone in your office, you
can interrupt their call by using the Priority Call feature. Use this feature for urgent calls only.
Program a telephone to make priority calls
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Make a priority call
To make a priority call:
1
2
Press ≤fl·.
Wait for a connection, then speak.
A person who receives a priority call while on another call has eight seconds to accept or block the
the priority call feature puts their active call, including conference parties, on Exclusive Hold and
connects your call.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
44 Chapter 3 Make a call
When you make a priority call, the display may show the following:
Call blocked
You tried to place a priority call to another telephone in your
system. The person you called has blocked your call. Try to call
later.
Please wait
The party you are calling has eight seconds to decide to accept
or reject your priority call.
Priority denied
The telephone you are calling is receiving a priority call at the
same time or cannot receive priority calls.
You can make a priority call only while your telephone display shows the following:
221 busy
PRIORITY
LATER
LATER
LATER
Calling 221
PRIORITY
Do not disturb
PRIORITY
On another call
PRIORITY
LATER
Ring Again
Use Ring Again when you call a person on your system and their telephone is busy or there is no
answer. Ring Again can tell you when they hang up or next use their telephone. You can use Ring
Again to tell you when a busy line pool becomes available.
Turn on Ring Again
To turn on Ring Again, press ≤¤ before you hang up.
Using Ring Again cancels any previous Ring Again requests at your telephone.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Make a call 45
Cancel Ring Again
Press ≤£¤ to cancel a Ring Again request.
Can't ring again
You cannot use Ring Again on your current call.You can use
Ring Again while you have a busy signal on an internal call or
line pool request, or while an internal call is ringing.
Ring Again?
Press YES to use Ring Again. Press NO if you select to send a
message.
YES
NO
EXIT
Message
When using Priority Call and Ring Again don’t work, you can leave a message on the person’s
Create a Conference Call
You can talk to two people at the same time.
1
2
3
Make sure you have two calls, one active and one on hold.
Press ≤‹.
Press the held line. (This action is automatic on the T7100 telephone.)
You can create a conference when you are on a call:
1
Put the call on hold. (This action is not necessary when the Automatic Hold feature is available
on your system.)
2
3
4
Make a second call.
Press ≤‹.
Press the held line.
Only the person who established the conference can use the procedures described in this section.
Disconnect one party
You can disconnect one party from a conference and continue talking to the other.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Chapter 3 Make a call
On a T7208, T7310, T7316 or M7324(N) telephone:
1
Press the line button of the call that you want to disconnect. The second call is automatically
put on hold.
2
3
Press ® to disconnect the first call.
Press the button of the held line to reconnect with the second call.
On a T7100 telephone:
1
Press ≤£‹ to put the first call on hold.
Press ≥ to put the second call on hold.
Press ® to disconnect the second call.
Press ≥ to reconnect with the first call.
2
3
4
or
1
2
3
Press ≤£‹and then press ≥ to put the second call on hold.
Press ® to disconnect the first call.
Press ≥ to reconnect with the second call.
Separate holding of two calls
For all system telephones except the T7100 telephone, you can place the two people in a
conference call on hold separately, so that they cannot talk to each other.
1
2
Press the line button of one call. The other call is automatically put on hold.
Press ≥. The second call is put on hold.
Now you can re-establish the conference.
3
4
5
Take one call off hold.
Press ≤‹.
Take the remaining call off hold.
Put a conference on hold
You can put a conference on hold, allowing the other two people to continue speaking to each other
by pressing ≥.
You can rejoin the conference by pressing either of the held line buttons.
For the T7100 telephone, press ≥.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Make a call 47
Split a conference
You can speak with one caller while the other call is on hold. You can switch between calls using
≥.
On a T7208, T7310, T7316 or M7324(N) telephone:
1
Press the line button of the caller with whom you want to speak. The other call is automatically
put on hold.
2
Press ≤‹to re-establish the conference.
On a T7100 telephone:
1
2
3
Press ≤£‹. The first call is put on hold.
Press ≥ to switch between calls.
Press ≤‹ to re-establish the conference.
Leave a conference call
You can remove yourself from a conference, and connect the other two callers.
Enter the Transfer feature code ≤‡‚.
When you remove yourself from a conference using the Transfer feature, and both calls are from
outside your system, one of the calls must have come to you on a disconnect supervised line, or the
call disconnects.
3 parties only
You are trying to add a fourth party to your conference call, or to
join two conferences together. Release one call from the
conference before adding another, or keep the two conferences
separate.
Conference busy
You have tried to make a conference call, but your system is
handling its maximum number of conference calls.
Line001 221
You are on a conference with the two lines or telephones shown.
You can drop out of the conference and leave the other two
TRANSFR
parties connected (Unsupervised Conference) by pressing
TRANSFR or entering the Transfer feature code.
Press held line
You have activated the Conference feature with one call active
and another on hold. Press the held line to bring that person into
the conference.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Chapter 3 Make a call
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Chapter 4
Time-saving features
This chapter shows you some time-saving features such as:
•
•
•
•
Autodial
Last Number Redial
Speed Dial
Saved Number Redial
Autodial
You can program memory buttons for one-touch dialing of internal or external telephone numbers.
You cannot use buttons for lines, answer or Handsfree/Mute as autodial buttons.
If the power to your Business Communications Manager system is off for more than three days,
autodial numbers and some other system programming can be lost from the memory.
To add an autodial button:
1
2
Press ≤•⁄ to program an external number or ≤•¤ for an internal number.
Select a button and then dial the number.
When programming Autodial you can use the following:
•
•
•
Last Number Redial
Saved Number Redial
destination codes (select an intercom button as the line)
Select a line for Autodial
To select a line for an external number, press the line or intercom button before you enter the
number. To select a line pool, press a programmed line pool button, or press an intercom button,
and enter a line pool access code.
If you select a line before pressing the autodial button, the call goes out on that line instead of the
line that is part of the autodialer programming.
For the T7100 telephone, program an external autodialer by using a line and not a line pool.
Note: If you do not include a line selection in an autodial number, the call uses
your prime line (if you have one).
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Chapter 4 Time-saving features
Use intercom as the line for Autodial
If you press an intercom button as the line for an external autodial number, you must include a
valid line pool access code or a destination code. If access codes for line pool or destination codes
change, remember to reprogram autodial numbers.
987___
Continue to enter digits until the number is complete. Press
√ or BKSP to erase an incorrect digit.
QUIT
BKSP
OK
Press ≥ or OK when you finish.
Autodial full
Button erased
The memory allocated to autodial numbers in your system is
full.
While programming external Autodial, you erased the button by
pressing ≥ or OK before entering any digits.
Enter digits
QUIT
Enter the number you want to program (selecting the line first if
necessary) exactly as if you were making a call.
OK
Intercom #: ___
QUIT
Enter the internal telephone number you want to program.
Invalid number
You are programming an internal autodial button and have
entered a number that is not an internal number on your system.
Enter a valid internal number. If the number you are entering is a
destination code, use external autodial.
Press a button
QUIT
Press the memory button you want to program.
Program and HOLD
Enter the number you want to program on the button, then press
≥.
Program and OK
QUIT
Enter the number you want to program on the button, then press
≥ or OK. You can include a line or line pool selection in an
autodial sequence by selecting the line before entering any
digits.
OK
Programmed
The number is correctly stored on the button.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Time-saving features 51
Last Number Redial
Press ≤fi to redial the last external number you dialed.
Last Number Redial records a maximum of 24 digits.
Note: If you have a Last Number Redial button programmed, use Button Inquiry
(≤•‚), then press the Last Number Redial button followed by (£) to
check the last number before you dial it.
Prevent Last Number Redial
Last Number Redial can be restricted at individual telephones.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Hidden number
The last number you dialed was a speed dial number that
displayed a name instead of the number. The number dials
correctly, but does not appear on the display.
No last number
You have not dialed an external telephone number since the last
power interruption or system reset.
Note: You can copy a number on an autodial button using Last Number Redial.
Speed Dial
Business Communications Manager provides two types of speed dialing:
•
•
system
personal
System Speed Dial programming allows you to assign two-digit speed dial codes to the external
numbers called most often. Personal Speed Dial programming allows users to program their own
speed dial numbers.
Speed dial numbers are subject to the same restriction filters as normally dialed numbers.Your
installer can program system speed dial numbers to bypass dialing restrictions.
To make a speed dial call
1
Press≤‚ to quickly dial external telephone numbers that programmed to speed dial codes.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
52 Chapter 4 Time-saving features
2
Enter the appropriate two-digit speed dial code.
System Speed Dial codes
System Speed Dial codes are numbered from 01 to 70. The installer assigns numbers to System
Speed Dial codes for the all the system.
Note: There is no difference between using User Speed Dial and using System
Speed Dial. Only the programming is different.
Personal Speed Dial
To add or change a Personal Speed Dial number on your telephone:
1
2
3
Press ≤•›.
Enter a two-digit code from 71 to 94 that you want to relate with a telephone number.
To include a line selection for this number, press the line or intercom button. To select a line
pool, press a programmed line pool button, or press an intercom button and enter a line pool
access code. For the T7100 telephone, you can only select a line pool.
4
5
Enter the number you want to program.
Press ≥ or OK.
01:9___
CANCL
Continue entering the number you want to program.You can
change the number by pressing BKSP or √. When you
are finished, press ≥ or OK.
BKSP
OK
OK
Enter digits
QUIT
Enter the telephone number you want to program exactly as if
you were dialing it normally. When you are finished, press ≥
or OK.
Invalid code
You have entered a code outside the code range (01-70 for
system, 71-94 for personal).
No number stored
Program and HOLD
There is no number stored on the speed dial code you have
dialed.
If you want to program a line or line pool selection for this speed
dial number, select the line or line pool. If not, enter the
telephone number exactly as if you were dialing it normally.
When you are finished, press ≥.
Program and OK
QUIT
If you want to program a line or line pool selection for this speed
dial number, select the line or line pool. If not, enter the
telephone number you want to program exactly as if you were
dialing it normally. When you are finished, press OK.
OK
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Time-saving features 53
Select a line
There is no line related with the speed dial number you are
trying to use. Select a free external line or line pool and enter the
speed dial feature code again.
Unknown number
The system cannot dial the number stored. Reprogram the
number.
Saved Number Redial
You can save the number of the external call you are on (provided you dialed the call) so that you
can call it again later. Each telephone can save one number at a time with Saved Number Redial,
but not one number for each line.
Note: You can copy a number on an autodial button using Saved Number Redial.
Save a number
To save a number, press ≤fl‡ while you are on the call.
Saved Number Redial records a maximum of 24 digits.
Dial a saved number
To dial a saved number, press ≤fl‡ when you are not on a call.
If you have a programmed Saved Number Redial button, you can use Button Inquiry (≤•‚)
to check the last number before you dial it.
Prevent Saved Number Redial
Saved Number Redial can be restricted at individual telephones.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Chapter 4 Time-saving features
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Hidden number
You have saved a speed dial number that displays a name instead
of the number. The number dials correctly, but does not appear
on the display.
No number saved
You have tried to save the number of an incoming call.You can
only save numbers that you have dialed.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Chapter 5
Handling calls
This chapter shows you how to:
•
•
•
handle many calls at a time
transfer calls
park a call
Use Hold
You can put a call on hold by pressing ≥.
When a call is on hold, the button indicator flashes on all telephones that have access to that line.
Any of these telephones can retrieve the call.
On the T7100 telephone, ≥ changes between two lines; one active, one on hold. The T7100
telephone cannot retrieve a call placed on hold by another telephone.
Retrieve a held call
You can connect to a call on hold by pressing the flashing line button of the held call.
Hold automatically
If a line is programmed with full autohold, you can switch from one call to another and have your
calls put on hold automatically.
Press the line button of the second caller. The current caller is put on hold automatically.
Listen on hold
If your call is placed on hold, you can hang up the handset while you wait for the other person to
return.
1
2
3
Press ≥.
Hang up the handset.
Press the line button of the call. You can hear indications from the far end that you are on hold
(for example, tones or music).
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
56 Chapter 5 Handling calls
When the person returns, lift the handset to continue the conversation.
4
Note: With Automatic Handsfree assigned to your telephone, you can use the
Handsfree/Mute feature instead of Listen on Hold.
Hold a call exclusively
You can put a call on Exclusive Hold so that you can retrieve it only at your telephone.
Press ≤‡· or ≤≥. The line appears busy on all other telephones, and the call cannot
be picked up by another person in the office.
On hold: LINENAM
You have placed one or more calls on hold. The name of the line
held the longest appears on the display.
Call Queuing
If you have more than one call ringing at your telephone, you can select the call that has the highest
priority by pressing ≤°‚⁄.
Call Queuing answers incoming external calls before callback, camped, and transferred calls.
Transfer calls
Transfer allows you to direct a call to a telephone in your system, within the Business
Communications Manager network, or external to your system.
1
2
3
To transfer a call, press ≤‡‚.
Call the person to whom you want to transfer the call.
If you want to talk to the person, wait for the person to answer and speak to person before
continuing.
4
When you are ready to complete the transfer, press ® or JOIN.
You cannot use Last Number Redial, Saved Number Redial, a speed dial code, Priority Call or
Ring Again to dial the number for a transfer.
The way a private network call is routed determines if it is possible for the system to return a
transferred call to you when the transferred call is not answered. When transferring a call to a
private network destination, remain on the line until the person to whom you are transferring the
call answers.
You cannot use the Line Pool feature code to access a line pool for a transfer. To use a line pool,
use a programmed line pool button, or press an intercom button, and enter a line pool access code.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Handling calls 57
If an auxiliary ringer is programmed to ring for calls on an external line, and you transfer a call on
that line without announcing the transfer, the auxiliary ringer rings for the transferred call.
Transfer external calls
If you transfer an external call to a busy telephone, or if there is no answer, the call automatically
rings again at the telephone that performed the transfer. The display indicates that the telephone
was busy or that no one answered.
When you transfer an external call to an external number, the external call you are trying to
transfer must be an incoming call on a disconnect supervision line.
While on a conference call, you can leave the conference and connect two callers using the
Transfer feature. If the other people are from outside the system, at least one of the callers must
have called you and both of the calls must be on disconnect supervision lines.
Note: Transfer by Hold on DID lines is not supported. After answering a call, the
line appearances on all other sets are free immediately to take other calls. This
allows you to receive a greater number of calls. Use the Call Park feature to
transfer a call.
In some conditions, you can experience lower volume levels when transferring an external call to
an external telephone, or when transferring two external callers from a conference call.
Cancel a transfer
You can reconnect to the person you are trying to transfer before the transfer is complete.
1
2
Press ≤£‡‚ or CANCL.
If you do not reconnect to your original call, press ® and then press the held line.
221>222
CANCL
You are talking to the person you want to transfer the call to.
Press RETRY if you decide to transfer the call to another person.
Press ® or JOIN to transfer the call.
RETRY JOIN
221 no reply
CALLBCK
The person to whom you tried to transfer a call did not answer.
Press CALLBCK or the flashing line button to reconnect to the call.
On the T7100 telephone, lift the handset.
Do not disturb
The person to whom you tried to transfer a call has Do Not
Disturb active on their telephone. Press JOIN to transfer the call.
Press RETRY to transfer the call to another person. Press CANCL or
the flashing line button to reconnect to the call (on the T7100
telephone, press ≤£‡‚).
CANCL
RETRY JOIN
Invalid number
You entered an invalid internal number. Press RETRY and enter
the number again.
CANCL
RETRY
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
58 Chapter 5 Handling calls
Line061 hung up
The external caller you were transferring hung up before the
transfer was complete.
Line061>221
Press JOIN to transfer the call on line 061 to telephone 221. Press
RETRY if, after talking to the person at extension 221, you decide
to transfer the call to another person.
CANCL
RETRY JOIN
Not in service
CANCL RETRY
The telephone to which you are trying to transfer a call is out of
service.
Restricted call
CANCL RETRY
You cannot transfer the call because of telephone or line
restrictions.
Still in trnsfer
CANCL RETRY
Complete the transfer in progress before you access a new
feature, answer another call or select an outgoing line.
Transfer denied
CANCL RETRY
Your transfer does not function for one of these reasons:
All the resources needed to perform a transfer are in use. Try
again later.
You have tried to transfer an external call to another external
party. Some restrictions apply.
You cannot transfer your conference call.
Transfer to:2___
CANCL RETRY
Press RETRY if you entered the wrong internal number or if the
person to whom you are transferring the call is not available.
Camp-on
You can transfer an external call to another telephone when all the lines assigned to that telephone
are busy.
1
2
Press ≤°¤.
Dial the number of the telephone to which you want to camp the call.
Camped calls appear on a line button on the receiving telephone, if one is available. If there is no
line button available, you receive a message on the display and hear Camp-on tones.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Handling calls 59
Each telephone in your system can handle one camped call at a time.
221 DND
The person to whom you redirected a call has Do Not Disturb
active on the telephone. The call has come back to you. Press the
CALLBCK button or the line button to reconnect to the call. On the
T7100 telephone, just pick up the handset.
CALLBCK
Camp denied
You have tried to camp an internal call.You can camp external
calls only.
Camp to:
CANCL
Dial the number of the internal telephone to which you want to
camp the call.
Camped: 221
CALLBCK
The telephone to which you camped a call did not answer the
call. The call has come back to you. Press CALLBCK or the line
button to reconnect to the call. On the T7100 telephone, just
pick up the handset.
Line061 hung up
A call you camped has come back to you, but the caller hung up
before you can reconnect.
Not in service
CALLBCK
The telephone to which you have camped a call is out of service
or is used for programming. The call has come back to you.
Press CALLBCK or the line button to reconnect to the call. On the
T7100 telephone, just pick up the handset.
Release a call
The line that the camped call is on is in use or that line does not
appear at your telephone. Release the line or release an internal
line.
Call Park
When you park a call, the system assigns one of 25 codes for the retrieval of the call. These codes
include the Call Park prefix, which can be any digit from 1 to 9, and a two-digit call number
between 01 and 25. For example, if the Call Park prefix is 1, the first parked call is assigned Call
Park retrieval code 101.
The system assigns Call Park codes in sequence, from the lowest to the highest, until all the codes
are used. A round-robin method means the use of different of codes ensures a call reaches the right
person, especially when more than one incoming call is parked.
The highest call number (the Call Park prefix followed by 25) is used only by analog telephones or
devices connected to the system using an ATA2 or an ASM. Analog telephones or devices cannot
use the other Call Park codes.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
60 Chapter 5 Handling calls
Your installer programs both the Call Park prefix and the delay before parked calls return to the
originating telephone. External calls parked for longer than the programmed delay return to your
telephone.
Park a call
You can interrupt a call to retrieve it from any telephone in your system.
1
2
Press ≤‡›.
Press PAGE to announce the retrieval code on your telephone display.
Retrieve a parked call
1
2
Select an internal line. (On the T7100 telephone, pick up the handset.)
Dial the Call Park retrieval code.
Your system installer can disable Call Park.
Already parked
The person you were talking to has parked your call. You cannot
park the same call.
No call to park
Invalid number
No call on: 101
Park denied
You have tried to use Call Park with no active call on your
telephone. If the call you want to park is on hold, reconnect to
the call before you park it.
You have entered an invalid retrieval code.
There was no call on the retrieval code you entered.
You have tried to park a conference call. Split the conference
and park the calls separately. The person who retrieves the calls
can reconnect the conference.
Parked on: 402
PAGE
Record the code shown. Use Page (≤fl‚) or press PAGE to
announce the call and its retrieval code.
EXIT
Parking full
All available retrieval codes are in use. Transfer the call or take
a message instead.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Handling calls 61
Callback
When you direct a call you have answered to another telephone, the system monitors the call to
make sure it is answered. If no one answers the call within a set length of time, the system returns
it to you.
Callback generates many different displays. Most occur after a set delay and are listed in the index.
Some occur immediately if the telephone to which you direct a call is out of service or not
available. These different displays are listed with the descriptions of the specific features such as
Transfer or Camp-on.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
62 Chapter 5 Handling calls
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Chapter 6
Forward your calls
If you leave your desk but want to receive calls at another location, you can forward your calls to
an internal or external telephone.
Call Forward
When you use Call Forward, all calls go to the destination you select, regardless of Forward on
busy (CFB) and Forward no answer (CFNA) feature programming.
To forward calls:
1
2
Press ≤›.
Enter the number of the telephone to which you want your calls forwarded.
To forward your calls to an external destination you must enter the route plus the dialing digits of
the external telephone. For example, if you need to dial 9 for external calls, then you must enter 9
plus the dialing digits to forward your calls to an external number.
Alternatively, you can use Line Redirection to forward calls outside the system. Line Redirection
takes priority over Call Forward.
Cancel Call Forward
Press ≤£› to cancel Call Forward.
To allow external destination programming you need to start a Unified Manager session.You must
assign Program Allow redirect to Yes for each telephone. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
If the telephone to which you forwarded your calls does not have the same external lines as your
telephone, the forwarded calls appear on intercom buttons.
Forwarded calls do not ring but the line indicator flashes on the telephone. You can answer the call
by pressing the button next to the flashing indicator.
Note: If you set up forward loops from one telephone to another in a circle, this
can result in unanswered calls at any location.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
64 Chapter 6 Forward your calls
Override Call Forward
When you call a person who has Call Forward to your extension, your call rings at that person’s
telephone.
Change the automatic Call Forward settings
The Call Forward feature allows for programming of calls not answered or when the line is busy.
You can define the number of times the telephone rings before call forwarding occurs. Program
this feature by starting a Unified Manager session.
Change Call Forward no answer
The Call Forward no answer feature redirects calls to another telephone in your system.
Line Redirection takes priority over Call Forward no answer.
For more information about changing Call Forward no answer using Unified Manager, see the
Business Communications Manager Programming Operations Guide.
Change the delay before a call is forwarded
You can assign the number of times that an incoming call rings at your telephone before the system
forwards the call. To estimate the delay time in seconds, multiply the number of rings by six. For
more information see the Business Communications Manager Programming Operations Guide.
Call Forward on busy
The Call Forward on busy feature redirects calls to another telephone on your system when you are
busy on a call, or when you have Do Not Disturb activated at your telephone. For more information
about changing Call Forward on busy using Unified Manager, see the Business Communications
Manager Programming Operations Guide.
Line Redirection takes priority over Call Forward on busy. The Call Forward feature or Call
Forward programming do not affect calls redirected by Line Redirection.
Telephones that have Call Forward on busy active can receive priority calls. If you are busy on a
target line call, another call to that target line redirects to the prime telephone for that target line.
DND on Busy
When you are busy on a call and a second call comes in, your telephone alerts you to the second
call with a light ring. If you find this second call and ring is disruptive, you can prevent a second
call by assigning Do Not Disturb (DND) on Busy to your extension.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Forward your calls 65
If you use DND on Busy, the line indicator for an external incoming call flashes, but your
telephone does not ring. Internal and private network callers hear a busy tone instead of ringing
when you are on the telephone. External callers are transferred to the prime set used in your
system. For more information about changing Do Not Disturb on Busy using Unified Manager, see
the Business Communications Manager Programming Operations Guide.
Forward on Busy takes priority over DND on Busy.
If an external call uses a target line, the call is processed according to the programming of the
target line. If the target line is busy, the caller hears a busy tone or routes the call to the prime set
for the target line, even with DND on Busy programming for the telephone.
Call Forward and voice mail
If you want a voice mail system to pick up unanswered calls automatically:
•
use the internal number of your voice mail as the destination when you program Forward no
Answer and Forward on busy
or
•
if your voice messaging system or service automatically retrieves calls, make the ring delay
greater than the delay used by your voice mail system
Forward denied
There are several reasons why you can get this message. For
example, you cannot forward your calls to a telephone that has
Call Forward programmed to your telephone.
Forward>221
CANCL
Your calls are being forwarded to telephone 221.
Not in service
Two or more telephones are linked in a forwarding chain, and
one is out of service or used for programming.
Line Redirection
Line Redirection allows you to send your external calls to a telephone outside the office.You can
decide to redirect all, or some of, your external lines.
Line Redirection takes priority over the Call Forward feature. If both features are active on a set,
incoming external calls on redirected lines route to the indicated Selective Line Redirection (SLR)
external destination. Incoming internal calls go forward to the indicated Call Forward destination.
You cannot use the Line Redirection feature on either a T7100 telephone or a telephone connected
to an ATA2 or an ASM.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
66 Chapter 6 Forward your calls
You redirect lines at a telephone, but after redirection programming, the lines redirect for the entire
system.
You can redirect only lines that appear at line buttons on your telephone.
You can answer the telephone if it rings while you are programming Line Redirection; however,
none of the call handling features are available until the feature times out. If you need to use a
feature to process the call, quit Line Redirection programming by pressing ≤. Do not press
® or you disconnect the call you are trying to redirect.
While you are programming Line Redirection, you do not receive any indication of calls that do
not actually ring at your telephone.
Be careful with redirection loops. If for example, you redirect your lines to your branch office and
your branch office redirects its lines to you, you can create a redirection loop. If these calls are
long distance, there can be charges.
In some conditions, callers can experience lower volume levels when you redirect calls to an
external location.
Allow a telephone to redirect calls
You can turn a telephone’s ability to redirect calls on and off.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
How Line Redirection is different from Call Forward
Call Forward forwards all calls that arrive at a selected telephone to an internal or external
telephone. Line Redirection redirects only the lines you define, no matter which telephones they
appear on, to a telephone outside the system.
Line Redirection takes priority over Call Forward.
Turn on Line Redirection
To turn on Line Redirection:
1
2
3
Press ≤°›.
Select the outgoing line to use for redirected calls.
Enter the number you need to redirect call to. To enter the telephone number to which you
want to redirect calls, use one of the following methods:
•
•
Press an external autodial button.
Enter an external telephone number (using no more than 24 digits) then press ≥ or OK.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Forward your calls 67
•
Press ≥ or OK if the line you have selected as the outgoing line is a private network line
that does not require you to dial digits.
4
Select the lines to redirect.
If you use ALL to redirect all your lines, ensure that you wait until all the lines on your telephone
light up before pressing ≥ or OK. If you press ≥ or OK before all the lines light up, those lines
not lit do not redirect.
You can continue to use the line selected for redirecting calls on other lines when the line is not
busy on a redirected call. To avoid redirection failing because the selected line is in use, select a
line pool with several lines in it. The system does not check that the number you give for line
redirection is a valid one. If you redirect to an invalid number, redirection fails.To avoid a
redirections failure, use an autodial button to enter the redirection number.You must program
autodial buttons used for line redirection to use a specific line.
Cancel Line Redirection
To cancel Line Redirection:
1
2
Press ≤£°›.
Select the lines you no longer want to redirect.
Turn the redirect ring for a telephone on or off
You can program a telephone to ring briefly (200 milliseconds) when you redirect a call on one of
its lines.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide
Note: If a telephone has redirect ring enabled, it rings briefly for redirected calls
on one of its lines when another telephone has set up the line redirection.
The following displays appear when redirecting lines:
Intercom
You selected the intercom button as the facility on which to
place the call. Enter a line pool code or a destination code.
Line Redirection
Press • or ADD to begin redirection. Press £ or REMOVE to
cancel a previous redirection.
QUIT ADD REMOVE
No line to use
You have one external line on your telephone, but you need a
second line to perform line redirection. Redirect your external
line using a line pool as the outgoing line.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
68 Chapter 6 Forward your calls
Outgoing line
You are trying to redirect a line and the line you have selected is
the outgoing line you have selected as a destination.You cannot
redirect a line to itself. Select another line.
Pool code: ___
QUIT
Enter a valid line pool access code.
Redir by 221
OVERRIDE
You have tried to redirect a line, but another person has
redirected that line. Press • or OVERRIDE to override the
previous redirection and redirect the line.
Redirect denied
You can redirect calls only on individual lines.
Select line out
QUIT
Select the line used to redirect calls out of the system.
Select line(s)
Press the lines to redirect. To release a line selection, press the
line to redirect again. Press ALL to redirect all your lines.
QUIT
ALL
Select line(s)
ALL
Continue to press the lines to redirect. Press ≥ or OK when
finished.
OK
Unequipped line
The line you are trying to redirect cannot be redirected because
the hardware does not support redirection.
The following displays appear when canceling redirection:
Select line(s)
Press the lines that no longer need redirection. The lines light up
when pressed. After you cancel redirection for a line you cannot
restore it by pressing the line again. Press ALL to cancel
redirection for all your lines. When finished, press ≥ or OK.
QUIT
ALL
Select line(s)
ALL
Continue to press the lines that no longer need redirection. Press
≥ or OK when finished.
OK
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Chapter 7
Communicating in the office
There are several features for communicating in the workplace, such as:
•
•
•
Page
Message
Voice Call
Page
The Page feature allows you to make announcements over the Business Communications Manager
system using the telephone speakers, or a loudspeaker system if one is available.
Make a page announcement
To make a page announcement:
1
2
Press ≤fl‚.
Enter a page type. Page types are:
⁄ through the telephone speakers (internal page)
¤ through an external speaker (external page)
‹ both internal and external (combined page)
3
4
5
If necessary, select a zone. Press ‚ for all zones.
Make your announcement.
Press ®.
Page Shortcuts
Instead of entering the Page feature code followed by the page type, you can enter the following
shortcut codes.
All
≤fl‚
Internal
External
Combined
≤fl⁄ + zone (0 to 6)
≤fl¤
≤fl‹ + zone (0 to 6)
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
70 Chapter 7 Communicating in the office
Activate and deactivate the Page feature
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Create page zones
A zone is any group of telephones that you want to group together for paging, regardless of their
location. You can assign one of six zones to each telephone. The maximum number of telephones
in a page zone is 50.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
You can make a telephone part of a page zone when the telephone has Page assigned as Y (Yes).
Your installer programs the following options:
•
•
a tone sounds before a page announcement begins
the maximum number of seconds a page announcement can last before it automatically times
out
Note: If a telephone has redirect ring enabled, it rings briefly for redirected calls
on one of its lines when another telephone has set up the line redirection.
Enter zone:___
ALL
Enter the required page zone number (0- 6) or press ALL.
Invalid zone
You have entered a page zone code that is not between 0 and 6.
Page choice:
SETS
SPKR BOTH
Page timeout
The time allocated for paging has expired.
Paging ALL
You are making a page. The display shows the page zone you have
selected. Press ≤ or ® when finished.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Communicating in the office 71
Paging busy
A page is being made in the page zone you have requested.
Note: You can make an announcement to one person by placing a voice call to
their telephone.
Using Page with external equipment
When you make a page that uses external paging equipment (external page or combined page), the
Long Tones feature automatically activates for the external paging system only. This allows you to
control optional equipment with the Long Tones feature.
Messages
The Messages feature allows you to leave a message on the display of another telephone in your
system or to analog telephones connected to an Analog Station Module (ASM). The Messages
feature indicates if you have any messages waiting.
The Messages feature uses a message waiting list to keep a record of your internal messages and
your (external) voice mail messages (if you have access to Business Communications Manager
Voice Messaging service with visual message waiting indication).
Send a message
You can leave a message on the display of another telephone in your system.You can send up to
four messages to different telephones, including your message center. If your telephone is a
direct-dial telephone or a CAP, you can send up to 30 messages.
Only the assigned direct-dial telephone for an analog telephone connected to an ASM can send
messages to analog telephones by pressing ≤⁄. Depending on the programming setup, the
analog telephone provides either a Stuttered Dial Tone or a Message Waiting Lamp to tell the user
of messages waiting.
For analog telephones connected to an ASM, the message waiting indicator remains on until the
user enters û£ßÞ. If the analog telephone has the Message Reply Enhancement
feature assigned as Yes, the message waiting indicator turns off automatically after you answer the
reply call, no matter where you answer the call. For more information about the Message Reply
Enhancement feature, see the Business Communications Manager Programming Operations
Guide.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
72 Chapter 7 Communicating in the office
To send a message:
1
2
Press ≤⁄.
On a telephone with a two-line display, press ADD. (This step is not necessary on a telephone
with a one-line display.)
3
4
Enter the internal number of the person you want to send the message. The person’s display
reads Message for you.
On analog telephones connected to an ASM, the message waiting indicator is activated.
Cancel a message you have sent
To cancel a message:
1
2
Press ≤£⁄. The display reads Cancel for:.
Enter the internal number of the person you sent the message.
Review your messages
You can receive up to four messages from different telephones, including your message center. A
single message from your message center can represent several messages.
On a telephone with a one-line display:
1
Press ≤flfi.
The display shows the first message.
2
Press • or £ to move through your messages.
On a telephone with a two-line display:
1
2
Press MSG.
The display shows the first message you received.
Press NEXT to move through your messages.
Reply to a message
You can call the person who sent a message, or your message center, while you are viewing the
message.
If your reply to a message is forwarded or is answered at another telephone using the Call Pickup
feature, the message remains on your telephone until you cancel it or contact the telephone that
sent the message.
Press ‚ to reply to a message on a telephone with a one-line display.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Communicating in the office 73
Press CALL to reply to a message on a telephone with a two-line display.
If you want to call your message center using a line different from the programmed line, exit your
message list and dial the message center telephone number using normal dialing methods.
Reply to a message using an analog telephone connected to an ASM
On an analog telephone connected to an ASM, press û¥ßÞ. The system
automatically retrieves and connects the user to the oldest message sender. (The message can
originate from either the assigned direct-dial telephone or the internal voice mail system.)
If the analog telephone has the Message Reply Enhancement feature set to Yes, and the sender is
the assigned direct-dial telephone, the message waiting indicator turns off automatically after
answering the reply call, no matter from where the call is answered.
For analog telephones connected to an ASM, using the Message Waiting Reply feature
(û¥ßÞ), retrieves only internal messages sent to the user.
Analog telephones connected to an ASM cannot retrieve external messages by using the Message
Waiting Reply feature (û¥ßÞ). For external messages, users must call back the
external voice mail center to retrieve their messages. When this happens, the message waiting
indicator on the analog telephone is turned off automatically.
If Voice Messaging is not installed on your system, only the assigned direct-dial telephone can
send messages to an analog telephone connected to an ASM using ≤⁄. The analog telephone
can in turn enter a single digit access code to reach the assigned direct-dial telephone and retrieve
messages.
If the assigned direct-dial telephone of an analog telephone connected to an ASM changes,
messages sent by the previous assigned direct-dial telephone remain in the incoming message list
of the analog telephone until you retrieve them.
Remove items from your message list
You can erase a message while you are viewing it in your message list. If the message is from your
message center, this action only erases the message notification at your telephone. To erase the
message at your message center, refer to your message center documentation.
To remove items from your message list on a telephone with a one-line display, press ≥.
To remove items from your message list on a telephone with a two-line display, press ERASE.
Remove items from your message list using an analog telephone connected
to an ASM
To remove both internal and external messages on an analog telephone connected to an ASM,
press û£ßÞ to invoke the Cancel Message Waiting feature.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
74 Chapter 7 Communicating in the office
On analog telephones connected to an ASM, the Cancel Message Waiting feature cancels the
oldest message received. The system no longer provides either a Stuttered Dial Tone or a Message
Waiting Lamp if there are no messages waiting.
View messages you have sent
On a telephone with a two-line display, you can view the messages you have sent.
1
2
3
Press ≤⁄.
Press SHOW to view your first sent message.
Press NEXT to view the rest of your sent messages.
Cancel denied
You have entered an invalid number when trying to cancel a
message.
Cleared>LINENAM
NEXT
You have cleared an external message from your message waiting
list. The message exists in your message center until you erase it
there.
In use: 221
You are trying to call from your message waiting list. The line that
you are trying to use is in use by the identified user in your system.
L061:LINENAMVMsg
You are viewing your message list. The display shows the number
and name of the line used for your message.
CLEAR
NEXT
CALL
Message denied
You have tried to send a message to an invalid internal number or
to a telephone that is out of service.
Message list
SHOW appears when you have remaining messages. Press SHOW to
review messages you have sent. Press ADD to send a new message.
SHOW
ADD
EXIT
Message to:
Enter the internal number of the telephone to which you want to
send a message.
Messages & Calls
MSG CALLS
You have one or more messages and one or more new Call Logs.
Press ≤°‚fl to change the first line of the display to the
current time and date.
No button free
You have no line button free with which to reply to a message.
No number stored
There has been no number programmed for the message center.
Contact your voice messaging service provider.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Communicating in the office 75
Start of list
NEXT
You are at the beginning of your list of messages. Press NEXT to
move through your messages.
Their list full
Your list full
You are trying to send a message to a user whose message waiting
list is full.
You have tried to send a message but your telephone’s list of sent
messages is full. Cancel one of the messages you have sent, if
possible, or wait until you have received a reply to one of those
messages.
Voice Call
You can make an announcement or begin a conversation through the speaker of another telephone
in the system.
Make a Voice Call
To make a Voice Call:
1
2
Press ≤flfl.
Follow the instructions on the display.
Mute Voice Call tones
When a voice call begins at your telephone, you hear a beep every 15 seconds as a reminder that
the microphone is on. To stop the beep, pick up the handset or press the handsfree button.
Answer a Voice Call using Handsfree Answerback
With Handsfree Answerback assigned to your telephone, you can respond to a voice call without
touching the telephone.
When a person makes a voice call to you, just start talking. The microphone on the telephone picks
up your voice.
After you have answered a voice call, you can put the call on hold, transfer it, or treat the call as a
normal call.
Handsfree Answerback is not available to the T7100 telephone.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
76 Chapter 7 Communicating in the office
Voice Call Deny
Press ≤°° to turn off the Voice Call feature on your telephone.
Voice calls ring like normal internal calls. Your other calls continue normally.
Cancel Voice Call Deny
Press ≤£°° to cancel the Voice Call Deny feature.
Dial voice call
Dial the internal number or press the internal autodial button of the
person you want to speak to.
Microphone muted
Your handsfree microphone is on the mute setting. Press © or
pickup your handset to respond to the voice call.
No voice call
The telephone receiving the call cannot accept voice calls for one
of the following reasons: the telephone is active or ringing with
another call; Call Forward is on; Do Not Disturb is on; Voice Call
Deny is on; it is not a Business Communications Manager
telephone.
Your call continues as a normal ringing call.
Voice call
The line is open for you to speak.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
77
Chapter 8
Track your incoming calls
You can track information about calls using a Call Log. This chapter shows you a Call Log, and
how to use it.
Call Log
If your system has the appropriate equipment and you subscribe to the call information feature
supplied by your service provider, you can record information about calls on an external line. The
line must appear on that telephone before you can log it, but it does not have to be a ringing line.
ISDN service packages that come with calling line identification (CLID) can supply the same
feature.
Call Log creates a record of incoming external calls. For each call, the log can contain:
•
•
•
•
•
•
•
sequence number in the Call Log
name and number of the caller
indication if the call was long distance
indication if the call was answered and by whom
time and date of the call
number of repeated calls from the same source
name of the line on which the call came
Call Log can help you to
•
•
•
•
keep track of discarded calls or calls not answered
track patterns for your callers (for example volume of calls and geographic area of calls)
record caller information quickly and accurately
build a personal telephone directory from log items
Information such as long distance indicator and the caller’s name and number, may not show in the
log. The appearance depends on the Call Display services provided by your local telephone
company and the caller’s local telephone company.
To use the features on the following pages, your telephone must have spaces available in its Call
Log. Your installer programs each telephone with an appropriate number of spaces.
Call Log options
You can select the type of calls to store in your Call Log. Select from four Autolog options: No one
answered, Unanswerd by me, Log all calls, No autologging.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
78 Chapter 8 Track your incoming calls
To use Call Log:
1
2
3
Press ≤•°›. The display shows the current option.
Press £ or NEXT to change the option.
Press ≥ or OK to select the display option.
Log a call manually
If your calls are not automatically logged, you can manually log call information when connected
to an external call. You can store information for your current call for future reference. For
example, you can:
•
•
•
record a caller’s information without using paper and pencil
record only selected calls as opposed to logging all calls
quickly record call information before a caller hangs up
Press ≤°⁄‹ to log an external call manually.
Delete old log items
Your log has a set number of items that it can hold. When the log is full, you can no longer log new
calls. When your log is full, the Autobumping function automatically deletes the oldest Call Log
item when a new call is logged.
Press ≤¡ÚÞ to enable autobumping.
Press ≤£¡ÚÞ to disable autobumping.
View your Call Log
To view your log:
1
Press ≤¡ÚÛ. The display shows the number of previously read items (old) and the
number of new items in the log.
2
3
Press ¥ or OLD to view old items; press £ or NEW to view new items.
Press â or RESUME to display the last item you viewed, the last time you accessed your Call
Log.
When you subscribe to Call Display services from your local telephone company, names and
numbers for external callers appear on the display.
View a Call Log item
Press √ or MORE to view the information for a call log item.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 Track your incoming calls 79
Erase log items
You must erase log items that you have read, to make space for new items in your log.
1
2
3
Display the item you want to erase.
Press ≥ or ERASE.
Press ® to exit.
If you accidentally erase an item, you can retrieve the item.
1
2
Press ≥ or UNDO after accidentally erasing an item.
Press ® to exit.
Make a call using Call Log
You can place calls from within your Call Log. The number stored for a call can vary depending on
the type of call. For example, if the call came from a Centrex or PBX system, you can trim the first
few numbers before you make the call. If the number you want to call is long distance, or if you
want to use a line pool, you may need to add numbers.
To place a call:
1
2
3
4
5
6
Display the log item for the call you want to place.
Display the related telephone number.
Press √ or TRIM, one time for every digit that you want to remove.
Dial any additional digits required.
Press an external line or line pool button.
Lift the handset or press Handsfree.
Create a password to your Call Log
To access your Call Log through a password:
1
2
3
Press ≤¥¡Þ. The displays shows New passwrd:.
Enter your four-digit password. The display shows Repeat New:.
Re-enter your four-digit password. The display shows Password changed, to confirm the
change.
To enter Call Log using a password:
1
2
Press ≤¡ÚÛ to enter Call Log. If you have programmed a password, the display shows
Password:.
Enter your four-digit password.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
80 Chapter 8 Track your incoming calls
If you do not remember your Call Log password, programming from Unified Manager can delete
the password. For more information about programming using Unified Manager, see the Business
Communications Manager Programming Operations Guide.
Change your Call Log password
1
2
3
4
Press ≤¥¡Þ. The display shows Old passwrd:.
Enter your old password. The display shows New passwrd:.
Enter your new four-digit password. The display shows Repeat New:.
Re-enter your password. The display shows Password changed to confirm the change.
Delete an assigned password
1
2
3
Press ≤¥¡Þ. The display shows Old passwrd:.
Enter your old password. The display shows New passwrd:.
Press ≥ or OK. The display shows No pswd assigned, to confirm the change.
Program a telephone to log calls automatically
Your installer can program each telephone to automatically log calls coming in on a line.
1:Unknown name
The caller's name is not available.
1:Unknown number
The caller’s number is not available.
12:KATE SMITH
_ indicates a new item.
NEXT
ERASE MORE
12øKATE SMITH
ø indicates that the call was answered.
NEXT
ERASE MORE
12¤KATE SMITH
¤ indicates a long distance call.
NEXT
ERASE MORE
49/1234567890123
/ indicates the stored number was trimmed to its final 11 digits.
Press à or MORE to show additional information about
the call.
NEXT
ERASE MORE
Call(s) bumped
One or more log entries are deleted by the Autobumping feature
while you are viewing at the Call Log.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 Track your incoming calls 81
Hold or release
In use: SETNAME
Jan 4 9:00a 3X
Hold or release your active call before entering Call Log.
The external line is in use.
The repeat call counter, shown with time and date, indicates the
number of calls you have received from the same caller.
NEXT
ERASE MORE
Line061
NEXT
ø227
This call was answered at another telephone (227).
This call was logged manually.
ERASE MORE
Line061
NEXT
øLogit
ERASE MORE
Line061
NEXT
This call was not answered.
ERASE MORE
Messages & Calls
MSG CALLS
There are one or more items in your message waiting list, and
there are one or more new items in your Call Log. Press
≤¡âß to change the first line of the display to the current
time and date.
New calls begin
No info to log
No log assigned
No resume item
You have viewed your last old log item and now you can view
your new log items.
No information is available for the call.
No log space has been assigned to the telephone.
The resume item has been removed because of Autobumping,
repeat call update, or log reallocation while you are looking at
the Call Log.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
82 Chapter 8 Track your incoming calls
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Chapter 9
Customize your telephone
You can customize your telephone to suit your needs. You can check the functions of buttons using
button inquiry. You can also:
•
•
•
•
change the contrast of display
change the language
adjust the ring type and volume
change button assignment
Adjust the contrast on the display
1
2
3
Press ≤•‡.
Press a number on the dial pad to select the contrast level you prefer.
Press ≥ to save your setting.
On a two-line telephone, you can use the UP and DOWN display buttons to adjust the contrast. The
number of contrast levels available varies from one telephone model to another.
Change the language on the display
You can select the language that appears on the display of each telephone. System software
supports four language options: Primary, Alternate, Alternate 2, and Alternate 3. All telephones
default to the Primary language at installation.Table 4 shows the different language options
Table 4 Language options
Language feature code
≤•fi‚⁄
≤•fi‚¤
≤•fi‚‹
≤•fi‚›
Language
Language - Primary
Language - Alternate
Language - Alternate 2
Language - Alternate 3
If you program ≤•fi‚⁄ to a memory button, you can press that button until the language
you want appears on the display. You cannot program ≤•fi‚¤, ≤•fi‚‹ or
≤•fi‚› to a memory button.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
84 Chapter 9 Customize your telephone
Change the type of ring
You can select one of four different rings for your telephone. This selection makes it easier to
identify your telephone in an open office.
1
2
Press ≤•fl.
Press ⁄, ¤, ‹, ›, or NEXT.
You hear the selected ring for two seconds.
3
Repeat until you hear the ring you like, then press ≥ or OK.
Adjust the Ring volume
1
Press ≤•°‚.
The telephone rings.
2
Press √ to adjust the volume: left end to decrease, and right end to increase.
Button Inquiry
You can check the function of any line, intercom, or programmed button on your Business
Communications Manager telephone by pressing ≤•‚ and a button. On the T7100
telephone, Button Inquiry shows your internal number followed by the function assigned to your
single memory button.
061 <LINENAME>
The display shows the number and name of the line. Press SHOW
to view the redirection status of the line.
SHOW
OK
123456789012345...
VIEWâOK
Press £ or press VIEWâ or áVIEW to view a number that is too
long to fit on the display. Press ≥ or OK when done.
221 <SETNAME>
The display shows the directory number of the telephone, and
the assigned name. Press NEXT to see the first line assigned to
ring at the intercom button.
NEXT
VIEWâ
<Feature name>
SHOW
The name of the feature assigned to a button appears on the
display when you press the button. Press £ or SHOW for
additional information.
OK
Press a button
EXIT
Press the button you want to check. Press ≤ or EXIT when
finished.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 Customize your telephone 85
Programming feature codes
You can program a feature code to a memory button.
Any memory button not programmed as an external or internal line, target line, Answer button, or
Handsfree/Mute button, is available for features.
1
2
3
Press ≤•‹.
Press the memory button you want to program with a feature.
Enter the appropriate feature code you want to assign to the button.
You cannot program the following feature codes on a memory button: Long Tones and any code
beginning with • except ≤•fi‚⁄ (Language Option) and ≤•‡ (Contrast
Adjustment).
Note: When you program a button with the line pool feature code, you must enter
a line pool access code after the feature code. The programmed line pool button
accesses a specific line pool, not the line pool feature.
Erase a feature button
1
2
3
Press ≤•⁄.
Press the feature button.
Press ≥ or OK to erase the button.
<Feature name>
SHOW
The name of the feature assigned to a button appears on the
display when you press the button. SHOW appears when there is
more information available.
OK
Press £ or SHOW for additional information.
Enter code:
If you are checking a speed dial button, enter the two-digit speed
dial code that you want to check.
F__
QUIT
Enter the feature code, or press ® or QUIT to end
programming or CLEAR to clear the numbers entered. The system
accepts the entry when you enter a valid feature code.
CLEAR
Feature code:
QUIT
Press ≤ and enter the feature code you want to assign to the
button. Check that the code is valid.
Feature moved
You have programmed a button with a feature programmed on
another button. The feature has moved to the button you just
programmed. The original button is now blank.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
86 Chapter 9 Customize your telephone
Press a button
Press the button you want to check. Press ≤ or EXIT when
finished.
EXIT
Program and HOLD
Enter the number you want to program and press ≥. To erase
the button, press ≥.
Program and OK
QUIT
Enter the number you want to program and press OK. To erase
the button, just press ≥ or OK.
OK
Default button assignments
During Startup, the installer chooses one of the available templates. Default features are assigned
automatically to the programmable buttons on telephones in the system, and vary with the template
and the telephone. The default features appear in the following tables in this chapter.
Rules of default button assignment
Line and Intercom buttons assigned by default templates can be changed in programming.
Handsfree/Mute and answer button features are not assigned by default. If these features are
defined, however, they are automatically assigned to specific buttons, as described on this and the
The T7316 and T7208 telephones can have up to eight Intercom buttons. They appear above the
Handsfree button at the bottom right-hand corner on your telephone.
Each telephone can have up to four answer buttons. They appear above Intercom buttons in the
right column and continue up from the bottom in the left column, replacing the features on those
buttons.
External line buttons appear in ascending line order, starting at the top button in the left column
(the top button on the T7208 telephone). If more than eight external lines are assigned to a T7316
telephone, or more than 12 to a M7324(N) telephone, assignment continues down the buttons on
the right column, erasing the feature codes on those buttons. Line buttons have priority over feature
access buttons except for the Handsfree, Intercom, or answer buttons.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 Customize your telephone 87
T7316 Button mapping
Button mapping for the T7316 telephone is unique because this telephone has more buttons than
the other telephone types. Internal autodial numbers are assigned to buttons, 11, 13, 15, 17, 19, and
21. Programmed external line buttons appear in descending line order starting with button 1. When
more than five external lines are programmed, assignment continues on button 6 and continues in
descending order.
Programmed intercom buttons appear on buttons 9 and 10. When you require more than two
intercom buttons, you can use button 8. When the Handsfree feature is programmed to your
telephone, the feature appears on button 10, moving intercom button(s) up one position.
Programmed telephone features are assigned to the remaining available buttons. Default internal
autodial numbers are assigned to the eight programmable buttons at the top of your T7316
Figure 7 Button assignment on the T7316 telephone
23
25
31
33
27
29
24
26
11
13
17
19
15
01
02
03
04
05
21
06
07
08
09
10
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
88 Chapter 9 Customize your telephone
T7316 and T7208 telephone button defaults
The default button assignments for the T7316 and T7208 telephones depend on the template
Table 5 T7316 button assignment template
PBX
Button Number
DID
DND
01
02
03
04
05
06
07
08
09
10
Line
Transfer
Transfer
Call Forward
Pick-Up
Call Forward
Pick-Up
Page-General
Conference
Last No. Redial
Intercom
Page-General
Conference
Last No. Redial
Intercom
Intercom
Intercom
Handsfree/Mute
Handsfree/Mute
Table 6 T7208 button assignment template
PBX
Button Numbers
DID
Pick-Up
01
02
03
04
05
06
07
08
Line
Transfer
Transfer
Last No. Redial
Page-General
Conference
Intercom
Last No. Redial
Page-General
Conference
Intercom
Intercom
Intercom
Handsfree/Mute
Handsfree/Mute
M7324 Button mapping
Button mapping for the M7324 telephone is unique because this telephone has a different layout
and more buttons than the other telephone types. Programmed external line buttons appear in
descending line order starting with button 1.
Programmed intercom buttons appear on buttons 23 and 24. When you require more than two
intercom buttons, you can use button 22. When the Handsfree feature is programmed to your
telephone, the feature appears on button 24, moving intercom button(s) up one position.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 Customize your telephone 89
Programmed telephone features are assigned to the remaining available buttons. Figure 8 shows
Figure 8 Button assignment on the M7324 telephone
01
02
03
04
05
06
13
14
15
16
17
18
07
08
09
10
11
12
19
20
21
22
23
24
M7324(N) telephone button defaults
The default button assignments for the M7324(N) telephone depend on the template applied. Table
Table 7 M7324(N) button assignment template
PBX
Button number
DID
º
º
º
º
º
º
º
º
º
º
ºLine <xx>
01
02
03
04
05
06
07
08
09
10
º
º
º
º
º
º
º
º
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Chapter 9 Customize your telephone
º
º
11
º
º
12
°
°
§
µ
ºSaved No.
13
§
14
µ
15
ºSaved No.
16
17
18
¶
¶
Ï
Å
¹
Æ
Æ
19
Ï
20
Å
21
¹
22
Æ
23
Æ
24
T7100 telephone button defaults
For all templates assigned to the T7100, the one programmable button on the T7100 telephone is
µ.
Note: The default Page button activates the External Page option
(≤fl¤).
Move line buttons
You can move external lines to different buttons on your telephone.
1
2
3
4
Press ≤•°⁄.
Press the line button you want to move.
Press the button to which you want to move the line.
Press ®.
You cannot move intercom, answer or Handsfree/Mute buttons on a CAP module.
Exchanged
The two buttons you selected have exchanged position.
Invalid location
You tried to move a line to a button that cannot be a line button,
such as an intercom button, Handsfree/Mute button, or an
answer button.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 Customize your telephone 91
Move line from:
QUIT
Press the button of the line you want to move. Press ≤ or
QUIT when you have finished moving lines.
Move line to:
QUIT
Press the button you want to move the line to. Neither of the
buttons is erased. The lines, or the line and feature, switch
places.
Press a line
The button you are trying to move is not a line button. If you are
trying to switch a line and a feature, move the line to the feature
button and not the feature button to the line.
Hide the message or calls indication
The display that shows you have messages or calls can be replaced with the current time and date.
If you are using a telephone with a one-line display, the message or call indication is hidden.
1
2
Press ≤°‚fl.
The current time and date appears on the first line of the display.
Press MSG or ≤flfi to see your messages, or press CALLS or ≤°⁄¤ to see your
calls.
Restore the messages and calls indication
You can retrieve your message and call information by using the display buttons that appear on the
second line of the display.
Press ≤£°‚fl to retrieve a message and call information.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
92 Chapter 9 Customize your telephone
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Chapter 10
Hunt Groups
The Hunt Groups feature allows access to a group of Business Communications Manager
telephones by entering a single extension number. This ensures that calls easily route to the
appropriate group.
Hunt Groups are used in conditions where a group of people performing the same task answer a
number of related telephone queries. Some typical uses of Hunt Groups are:
•
•
•
a sales department answering questions on product prices or availability
a support department answering questions describing the operation of a product
an emergency department answering calls for help
As an example, consider Hunt Groups that route calls to a support service such as a help line for a
software company. Specialists handling Product A can be in one group, and specialists handling
Product B can be in another group. Incoming calls hunt for the next available telephone in the
group. If no telephone is available, the call is placed in a queue or is routed to an overflow
telephone.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
You can make programming changes to the following Hunt Group settings:
•
•
•
•
•
members of a group and member position in a group
line assigned to a group
distribution of incoming calls
how long the system looks for available members
where a call goes if all members are busy
Features affected by Hunt Groups include:
•
•
•
•
•
•
•
•
•
Call Forward All Calls
Call Forward No Answer
Call Forward on Busy
Group Pickup
Transfer via Hold
Priority Call
Line Redirection
Page Zones
Voice Call
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
94 Chapter 10 Hunt Groups
Members of the group
Members of the group can be any telephones in the system or portable telephones. Each telephone
can be in more than one Hunt Group, and considered a member in each Hunt Group, increasing the
total number of members in the system.
There is only one appearance of the same Hunt Group on a set. Hunt Group extension numbers
cannot be members of other Hunt Groups. An extension number can be related with a member of a
Hunt Group and is called a member extension number.
Distribution mode
There are three modes of call distribution:
•
Broadcast—rings every set in the group at the same time. Calls are handled one at a time; other
calls are put in a queue. When a call is picked up, the call next in the queue is shown to the
Hunt Group without having to wait for queue time-out.
In Broadcast mode you can program all the attendants in the group to share the load of
answering large volumes of calls. All sets automatically display the calling line identification
(CLID), if available. A known example is a fund raising campaign where a group of operators
are waiting to take each call as it comes in.
•
•
Sequential—starts the call at the first set in the Hunt Group and distribution is complete when
the first free set is found. Simultaneous calls can be shown. Distribution is order based.
In Sequential mode, you can program your top salesperson to be the first member of the group
to receive incoming calls.
Rotary (Cyclic)—the call starts at the set after the one which answered the last call.
Distribution is complete when the next free set is found. Simultaneous calls can be shown.
Distribution is order based.
In Rotary (Cyclic) mode, you can ensure that all your help line people receive calls on an equal
basis, instead of one person receiving most of the calls. The call rings at one set at a time in a
rotation.
If a Hunt Group has available members but no one answers the call, the call routes through the
Hunt Group list until either a person answers the call or the queue time-out occurs. In the second
case, the call routes to the overflow position. After a call goes to the overflow position it is no
longer a Hunt Group call.
For information about Hunt Groups, see the Business Communications Manager Programming
Operations Guide.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
95
Chapter 11
Telephone features
This chapter shows you how to:
•
•
•
•
•
•
•
move a telephone
prevent a call from ringing at a telephone
turn Privacy on and off
use the Handsfree and Mute features
time a call
recover from an accidental disconnect
play music in the background
Moving telephones
Caution: You can be required by law to report any telephone moves to your local
telecommunications carrier or 911 service provider. For more details, ask your
local carrier, your local 911 service provider, and/or your local
telecommunications service provider.
When automatic telephone relocation is enabled in programming by your installer, you can move
your telephone from one jack to another without losing any of its custom programming.
Hunt Groups
Business Communications Manager allows you to establish Hunt Groups in your system. A Hunt
Groups is a group of telephones that is accessible by entering a extension number. The Hunt
Groups feature ensures calls route to the appropriate people. For more information about Hunt
Prevent calls from ringing at your telephone
You can prevent calls from ringing at your telephone, either when you are away from your desk or
while on another call with the Do Not Disturb (DND) feature.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
96 Chapter 11 Telephone features
Use Do Not Disturb
After you turn Do Not Disturb on, calls are forwarded to the prime telephone when there is no
other telephone on which the line appears. If there is another telephone that shares the same line,
the call can be answered by that person. (The Delayed Ring Transfer feature transfers all calls not
answered, to the prime telephone after a defined time.)
Do Not Disturb prevents voice calls from alerting at your telephone. Voice calls appear as normal
intercom calls.
Cancel Do Not Disturb
Press ≤£°fi to cancel Do not Disturb.
Allow calls
Your telephone receives calls normally.
Stop calls
Press ≤°fi to stop calls from ringing at your telephone.
You only receive priority calls at your telephone. A line button flashes when you receive a call, but
the call does not ring.
Refuse to answer a call
If your telephone rings while you are on a call, you can refuse to answer the second call, even if it
is a priority call.
To refuse a call, press ≤°fi while your telephone is ringing.
Turn Privacy on or off for a call
You can configure lines in your system to have automatic privacy. With a line not programmed
with privacy, anyone with the line assigned to their telephone can join your call by pressing the line
button. With a line programmed with privacy, one person at a time can use the line.
Privacy control cannot be for internal or conference calls.
When another telephone joins a call, the participants on the call hear a tone, and a message appears
on the telephone display. It is not possible to join a call without everyone hearing this tone.
Note: The Privacy feature does not apply to target line calls.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 Telephone features 97
Create a conference call by releasing privacy
With a line programmed with privacy, you can turn privacy off to allow another person with the
same line to join in your conversation and form a conference. All the rules for a conference apply
but there is one line in use, instead of the normal two. This means that you cannot split a
conference set up using Privacy.
1
2
Press ≤°‹.
Tell the other person to press the line button and join your conversation.
Only two Business Communications Manager telephones and the external caller can take part in
this kind of conference.
Make a call private
With a line programmed not to have privacy, you can turn privacy on for a call, preventing other
people with the same line from joining.
Press ≤°‹ to make a private call.
Handsfree and Mute
You must assign the ability to use Handsfree to on or off for each telephone. Also program the type
Handsfree for a telephone to use a headset.
Answer calls without lifting the handset
1
2
Press the line button for the ringing call.
Press the handsfree button. The telephone’s internal microphone and speaker automatically
turn on.
Handsfree is not available for a T7100 telephone.
Note: Direct your voice toward the telephone. The nearer you are to the
telephone, the easier it is for the microphone to transmit your voice to
your listener.
Make calls without lifting the handset
1
Press the handsfree button. The telephone’s internal microphone and speaker automatically
turn on.
2
3
Dial your call.
Speak normally.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
98 Chapter 11 Telephone features
Mute Handsfree
1
Press © to switch off the telephone microphone so that you can speak to a person in your
office while you are on a handsfree call. The display reads Microphone Muted.
2
Press the handsfree button to turn the microphone back on again and continue your handsfree
call.
Change a normal call to handsfree
1
2
Press the handsfree button.
Hang up the handset.
Change a handsfree call to a normal call
To switch from handsfree, lift the handset.
Handsfree
The indicator next to the handsfree button is solid when you have Handsfree turned on. It flashes
when you mute the microphone.
Wait for your caller to finish speaking before you speak. The microphone and speaker cannot both
be on at the same time. Your caller’s voice can be cut off if you both speak at the same time.
Interruptions such as a tapping pencil can be loud enough to turn on your microphone and cut off
your caller’s speech.
To prevent an echo, keep the area around your telephone free of paper and other objects that can
screen your microphone. Turn down the microphone’s volume (press the left end of √
while speaking) to prevent feedback. When you change the volume level, both the microphone and
speaker volume adjust to prevent feedback problems.
Position the telephone so that any unavoidable local noise (such as an air conditioner) is behind it.
This position limits the amount of background noise.
Note: In open office environments, use the handset when handsfree
communication is not necessary or when you need privacy during a call.
Another option is to use a headset.
Change Handsfree for a telephone
You can program the type of Handsfree used with each telephone or activate Handsfree
Answerback.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 Telephone features 99
Handsfree Answerback
Handsfree Answerback allows you to answer a voice call without lifting the handset. Handsfree
Answerback is always turned off for a T7100 telephone.
You can turn Handsfree Answerback on or off for a telephone programmed to use Handsfree. You
need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Hearing aid compatibility
The handsets on all system telephones are compatible with hearing aids as defined in the FCC
rules, Part 68, section 68.316. Not all hearing aids are optimized for use with a telephone.
Call Duration Timer
Press ≤‡‡ to see how long you were on your last call, or how long you have been on your
current call.
221 02:47
The display shows the last call you made, or the current call, and
the total elapsed time in minutes and seconds.
Line061 01:45
You parked your last call. You cannot see the length of time a
call was parked.
Accidental disconnect
If you accidentally drop the handset back into the telephone cradle while answering a call, you can
retrieve the call.
Pick up the handset again or press the handsfree button within one second to reconnect to your call.
Disconnect supervision
When disconnect supervision is assigned to a line, the system detects when an external caller
hangs up and releases the line for other uses. The installer assigns disconnect supervision.
Time
Press ≤°‚‹ to display the current date and time while you are on a call.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
100 Chapter 11 Telephone features
Press ≤°‚fl to display the static time.
Press ≤ £°‚fl to cancel the static time feature.
Background Music
Press ≤°fl to listen to music through your telephone speaker.
Your installer makes this feature available to all telephones in programming. You need to supply a
music source, such as a radio, which is attached to your system.
Warning: According to U.S. copyright law, a license can be required from the
American Society of Composers, Authors and Publishers or a similar organization
if radio or TV broadcasts are transmitted through the Background Music feature
of this telecommunication system.
Nortel Networks hereby disclaims any liability occurring as a result of failure to
get a license.
Cancel Background Music
Press ≤£°fl. The music stops automatically if you make or answer a call.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
101
Chapter 12
System features
This chapter describes how Business Communications Manager sends and receives different types
of information. This chapter also shows you a variety of services and how to use them.
ISDN
Integrated Services Digital Network (ISDN) technology provides a fast, accurate and reliable
means of sending and receiving data, image text and voice information through the telephone
system.
Using ISDN Primary Rate Interface (PRI) or Basic Rate Interface (BRI) allows for faster
transmission speeds and the addition of many powerful business applications, including remote
LAN access, video conferencing, file transfer, and Internet access.
Your installer or service representative configures your ISDN services and telephone equipment.
For more information about ISDN, see the Business Communications Manager Programming
Operations Guide.
You can use selected ISDN network features from a telephone in the system.Your central office
switch (ISDN network) determines which features are available to you.
Network name display
Your system shows the name of an incoming call when it is available from the service provider.
Name information appears on the display of a telephone. If the Calling Party Name has the status
of “private” it appears on the display as “Private name.” If the Calling Party Name is not available
it can appear on the display as “Unknown name.”
Your telephone display shows the name of the called party on an outgoing call, when available
from your service provider.
Your system sends the Business Name concatenated with the set name on an outgoing call but only
after the Business Name is programmed.
Name and number blocking
When activated, ≤°⁄· allows you to block the outgoing name and/or number on a
per-call basis. All telephones in the system can use the Name and number blocking feature.
Ask your customer service representative if this feature is compatible with the features available
from your service provider.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
102 Chapter 12 System features
Use alternate or scheduled services
There are three types of services for Business Communications Manager to handle calls in a
different way on different days, and at different times of the day:
•
•
•
Restriction service
Ringing service
Routing service
The installer customizes and programs all three services, that is the six schedules available to each
service. The installer programs one telephone used to turn services on and off, and display what
services are in use. This specific telephone is called the control telephone.
Restriction service
Restriction service prevents a user from dialing some types of calls from a telephone or from lines
that are available at the telephone. The installer programs restrictions.
Ringing service
Ringing service makes additional telephones ring for incoming calls on external lines. For
example, incoming external calls can ring at a security guard’s telephone during the night, or calls
to one attendant can ring at another attendant’s telephone during lunch. Ringing service does not
suppress your normal ringing assignment.
Routing service
Routing service allows you to assign alternate routes to calls.You can take advantage of lower
costs available on selected routes for some days and at some times. Both the normal and alternate
routes are programmed by your installer.
Turning services on and off
Three programming settings: Manual, Automatic and Off, control how the system uses different
services and their schedules.
•
•
Manual allows you to turn the service on and off at any time from a control telephone using a
feature code.
Automatic allows you to use the pre-assigned stop and start time for a service. You can enable
and cancel the service by entering the appropriate feature code at a control telephone. If you
select this setting, you use the start and stop times programmed by your installer.
•
Off prevents the service from being activated.
For more information about programming using Unified Manager, see the Business
Communications Manager Programming Operations Guide.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 103
Each schedule can have its configuration of a service which works separately from automatic start
and stop times. For example, in Restriction service, the Night schedule prevents people from
making long distance calls. Calling the restriction Night schedule does not limit the use to that
specific schedule. You can turn the Night schedule for Restriction service on or off as needed any
time of the day or night. If you decide to run a service on a schedule, the system uses the start and
stop times used for the schedule you set up.
Turn services on and off using feature codes
You can access the master control for services through the Unified Manager. The following feature
codes allow access and control of the day-to-day use of services.
≤°‡⁄
Turns on Ringing service. When used at the direct dial telephone,
it activates the alternate direct dial telephone (extra dial
telephone).
≤£°‡⁄
≤°‡¤
Turns off Ringing service.
Turns on Restriction service.
Turns off Restriction service.
Turns on Routing service.
Turns off Routing service.
≤£°‡¤
≤°‡‹
≤£°‡‹
To turn a service on:
1
2
Enter the appropriate feature code from a control telephone.
Press NEXT to move through the schedules until the display shows the version of the service
you want turned on.
3
Press OK to select the setting, or press QUIT to exit the feature without making any changes.
To turn a service off, enter the appropriate feature code from a control telephone.
Caution: Assigning a service as Normal is not the same as canceling a service
using a feature code. If you assign the service as Normal, the normal version of a
service overrides any automatic schedule and remains until you manually cancel
it. When you cancel service by feature code, you return to the automatic schedule.
View active services from a two-line display telephone
When a service is active, the control telephone display shows Services ON.
1
2
3
Press LIST. The display shows the first active service and the schedule in use.
If there are several active services, press NEXT to view all of the services.
Press EXIT to exit the feature.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
104 Chapter 12 System features
View active services from a one-line display telephone
1
2
3
Press ≤°‡‚. The display shows the first active service.
Press £ to move through the active schedule.
Press ® to exit.
You are viewing the active services. Press £ or NEXT to view the other
active services. Press ® or EXIT to quit.
<Sched> Restr'n
EXIT
NEXT
The name of the current Restriction service schedule appears on the
display. Press £ or NEXT to view the other Ringing service schedules.
Press ≥ or OK to select the required schedule.
<Sched> Restr'n
QUIT
OK
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
You are viewing the active services. Press £ or NEXT to view the other
active services. Press ® or EXIT to quit.
<Sched> Ringing
EXIT
The name of the current ringing service schedule appears on the
display. Press £ or NEXT to view the other Ringing service schedules.
Press ≥ or OK to select the required schedule.
<Sched> Ringing
QUIT
OK
You are viewing the active services. Press £ or NEXT to view the other
active services. Press ® or EXIT to quit.
<Sched> Routing
EXIT
The name of the current Routing service schedule appears on the
display. Press £ or NEXT to view the other Routing service schedules.
Press ≥ or OK to select the required schedule.
<Sched> Routing
QUIT
OK
Press ≥ or OK to select this schedule, £ or NEXT to view the next
available schedule, or ® or QUIT to exit. If you select this schedule, it
remains active until the next automatic schedule begins.
<Sched> until *
QUIT OK
You have entered the Show services feature code and there is no active
service.
No services ON
There is a service active in your system. Press • or LIST to view the
active services.
Services
LIST
ON
Services that turn on automatically have an asterisk (*) appearing before the name on the display.
You can not manually activate or cancel scheduled services. However, you can override a schedule
service by manually activating another schedule.
The control telephone can override services turned on and off according to a schedule by entering
a Services feature code, and selecting a different schedule. This override remains until canceled. If
you select a schedule with an asterisk (*), the next automatic service schedule comes into effect at
the programmed time.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 105
Direct-dial calls to a direct-dial telephone ring at the extra dial telephone when you enter the
Ringing service feature code (≤°‡⁄) at that direct dial telephone. The installer assigns the
extra dial telephone. Note that only the extra dial telephone is activated, not the actual Ringing
service (unless that direct-dial telephone is a control telephone).
Note: The system provides six service schedules: Night, Lunch, Evening, Sched
4, Sched 5, and Sched 6.Your installer can change these names to meet your
business requirements.
User passwords
User passwords prevent unauthorized or accidental changes to your system. There are two types of
user password: Registration and Call Log.
Registration password
The Registration password controls the registration of companion portables to the Business
Communications Manager system. For more information see the Business Communications
Manager Programming Operations Guide.
Log password
If a person does not remember their Call Log password, you can clear the previously assigned
password in programming. The person can enter a new password from their telephone.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Special telephones
You can dedicate telephones to serve special functions such as:
•
•
•
Direct dial
Hotline
Control
Direct dial
You can reach the direct dial telephone by dialing a single digit. The direct dial telephone is
normally in a central location, such as an attendant’s desk. You can have up to five direct dial
telephones for your system. The direct dial telephone is normally the prime telephone or the
central answering position (CAP).
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
106 Chapter 12 System features
The direct dial telephone can send up to 30 messages and can activate services to activate the extra
dial telephone.
Change direct dial telephone assignments
Your installer assigns the direct dial telephone during installation.
You can change the direct dial telephone. You need to start a Unified Manager session to program
this feature. For more information about programming using Unified Manager, see the Business
Communications Manager Programming Operations Guide.
You can assign any number of telephones to call the direct dial telephone.
Hotline
A hotline telephone calls a set internal or external telephone number when you pick up the handset
or press the handsfree button.
Note: Label the hotline telephone to warn anyone using it that it is active.
Hotline bypass
Press a line button, or use the Pre-Dial or Automatic Dial feature before you pick up the handset or
Make a telephone a hotline telephone
You can set up a telephone as a hotline.
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
The Internal option assigns an internal number. The External option assigns an external number. If
you select an external number, you can select the line on which the call is made: the prime line, an
external line, a line in a line pool, or a line selected by the routing table. If you select a line pool,
you must indicate the line pool access code. If you select the routing table, the number dialed is
considered as a destination code and routes according to the routing tables.
The installer programs a telephone’s prime line, line pool access codes, and access to a line pool.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 107
Control telephone
The control telephone allows you to place the telephones and external lines for which it is
102.
Set lock
Set lock limits your ability to customize a telephone. There are three levels of Set Lock:
•
•
•
Partial
Full
None
None allows you to access all features on your telephone.
Partial prevents:
•
•
•
•
•
programming autodial buttons
programming the user speed dial numbers
programming feature buttons
moving line buttons
•
changing dialing modes
(Automatic Dial, Pre-Dial, and Standard Dial)
•
•
using Voice Call Deny
saving a number with Saved Number Redial
changing the display language
Full, with the restrictions described for Partial lock, prevents:
•
•
•
•
changing Background Music
changing Privacy
changing Do Not Disturb
using Ring Again
•
•
•
•
using Call Forward all calls
using Send Message
using Trunk Answer
activating Services
Change Set Lock programming for a telephone
You need to start a Unified Manager session to program this feature. For more information about
programming using the Unified Manager, see the Business Communications Manager
Programming Operations Guide.
Auxiliary ringer
An auxiliary ringer is an optional device connected through a RJXX connection to your system.
The auxiliary ringer is best suited to factory type locations that require loud ringing bells or horns.
Turn the auxiliary ringer on or off
You need to start a Unified Manager session to program this feature. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
108 Chapter 12 System features
Your installer can program the auxiliary ringer to start ringing for incoming lines as part of
Ringing Service.
Host System dialing signals
You can access host systems, such as private branch exchanges (PBX) from the system by using
host system signaling features (known as end-to-end signaling). These features either send a
special signal to the host system or allow you to program delays required by host systems in
external autodial or speed dial sequences.
Link
If you connect the system to a private branch exchange (PBX), you can use a Link signal to access
special features. On some telephones, Link is called FLASH.
You can include the Link signal as part of a longer stored sequence on an external autodial button
or in a speed dial code. The Link symbol (Û) uses two of the 24 spaces in a dialing sequence.
Prevent a telephone from using Link
You can limit the use of Link on individual telephones.You need to start a Unified Manager
session to program this feature. For more information about programming using Unified Manager,
see the Business Communications Manager Programming Operations Guide.
Note: If you connect the system to a private branch exchange (PBX), you can
program Link on a memory button for one-touch access.
Pause
The Pause feature enters a 1.5 second delay in a dialing sequence on an external line. The use of
this feature is often required for signaling remote devices, such as answering machines, or when
reaching through to PBX features or host systems.
You can program more than one pause in an external autodial or speed dial sequence.
The Pause symbol (Ý) uses one of the 24 spaces in a dialing sequence.
For pulse dialing, • inserts a 1.5 second pause into the dialing sequence.
Long Tones
The Long Tones feature allows you to control the length of a tone to signal devices such as fax or
answering machines which require tones longer than the standard 120 milliseconds.
1
While on a call, press ≤°‚°.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 109
2
Press the dial pad buttons to produce the appropriate tones. Each tone sounds while you hold
down the button.
You can use Long tones on any call except a conference call.You can use internal lines of the
system to activate a device connected to an ATA2 or an ASM in another area of your office, or
external lines to access devices outside the system.
At the appropriate time, press any dial pad button. Hold each button
Long Tones:
down for as long as necessary. Press ≤ or ≥ to cancel Long
Tones.
Run/Stop
Run/Stop inserts a break point into a sequence of dialed numbers or characters used for automatic
dialing. This can be necessary when you are connecting to a PBX or similar host system.
For example: you can call a company with an automated attendant that instructs you to dial the
internal number you need. You can program the company number, a Run/Stop, then the internal
number on one external autodial button. Press the autodial button one time to dial the company
number. When you hear the automated attendant, press the autodial button again to dial the internal
number.
The Run/Stop symbol (ß) uses one of the 24 spaces in an autodial or speed dial sequence.
You can include up to three Run/Stop commands in a dialing string. The system ignores a fourth
Run/Stop, and any digits or commands that follow three Run/Stop commands in a programmed
dialing sequence.
Wait for Dial Tone
Wait for Dial Tone causes a sequence of numbers to pause until dial tone is present on the line
before continuing to dial. You can use this feature if you must dial a remote system and then wait
for dial tone from that system before dialing the remainder of your number.
The Wait for Dial Tone symbol (à) uses two of the 24 spaces in an autodial or speed dial
sequence.
You have entered a code limited to a programmed autodial or speed
dial sequence, not on a call you dial directly. Run/Stop are for use in
programmed dialing Autodialers only.
Invalid code
Pulse or tone dialing
If your external lines use pulse dialing, you can switch temporarily to tone dialing. Tone dialing
allows you to communicate with devices such as answering machines, to access the features that
PBX systems can provide, or to access another system remotely.
Press £ while on an active line. After you hang up, your telephone returns to pulse dialing.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
110 Chapter 12 System features
Pulse dialing for a call
If your external telephone lines use pulse dialing, you can switch to tone dialing by pressing £
after selecting the line. Tone dialing allows your telephone to communicate with devices and
services that respond to tone signals, such as automatic switchboards, and fax or answering
machines.
Access your system from an external location
You can use the lines and some of the features of Business Communications Manager from outside
the system. You can access the lines and some of the features over the public telephone network
when away from the office, or you can call from another system, over a private network.
It is important to maintain the security of your system by limiting access to authorized users and
limiting those users to the features they need.
For example, a sales representative out of the office needs to make long distance calls to the
European office. Your system has a leased line to Europe with reduced transatlantic charges. You
provide the sales representative with a Class of Service password that gives access to the
transatlantic line. The sales representative can telephone into the system from a hotel, enter the
Class of Service password, and use the leased transatlantic line to make calls.
Remote users can access system lines, line pools, the page feature, and remote administration (if
enabled through Software Keys). The exact facilities available to you through remote access vary
depending on how your installer set up your system.
Note: If the loop start line used for remote access is not supervised, auto-answer
does not function and the caller hears ringing instead of a stuttered tone or the
system dial tone.
Direct Inward System Access (DISA)
Control access to your system with direct inward system access (DISA). Access to your system
from the public telephone network must be controlled with DISA. If your installer programs the
line used for remote access to answer a call automatically and wait for a DISA internal number,
callers hear a stuttered dial tone and must enter a Class of Service password before they are
allowed into the system.
Class of Service (COS)
To control the level of telephone service a remote user can access, the installer can assign a remote
filter and remote package to the line used for remote access. The remote filter limits the numbers
dialed on the line, and the remote package limits the use of line pools and the page feature. To
change the restrictions for the line, the user can enter their Class of Service password when the
system answers with DISA, or dial the DISA internal number and enter their Class of Service
password.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 111
Class of Service (COS) passwords
Class of Service passwords permit controlled access to a system’s resources both by internal and
remote users. When you enter a Class of Service password at a telephone, the restriction filters
related with your Class of Service password apply, instead of the normal restriction filters. In the
same way, when a remote user enters a Class of Service password on an incoming auto-answer
line, the restriction filters and remote package related with their Class of Service password apply,
instead of the normal restriction filters and remote package. The installer programs the COS
passwords.
Users must memorize their COS passwords instead of writing the password down. Delete an
employees’ COS passwords when they leave the company. Normally, each user has a separate
password. However, several users can share a password or one user can have several passwords.
Change your Class of Service
Enter a Class of Service password when you want to make a call normally restricted on a line or
telephone.
To change the restriction filters on a line or telephone:
1
2
Press ≤fl°.
Enter the six-digit COS password.
COS passwords allow you to define individual passwords and determine the restriction filters, and
remote package related with each.
Maintain security
To maintain the security of your system, the following practices are recommended:
•
•
•
Warn a person to whom you give the remote access number, to keep the number confidential.
Change Class of Service passwords often.
Warn a person to whom you give a Class of Service password, to remember the password and
not to write it down.
•
Delete the Class of Service password of a person who leaves your company.
Warning: Remote users can make long distance calls.
Remember that a remote user can make long distance calls that are charged to
your company. They can also access line pools and make page announcements in
your office.
Remote access over the public network
1
2
Dial the system remote access number.
When you hear a stuttered dial tone, enter your COS password.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
112 Chapter 12 System features
Wait for the system dial tone.
3
To use the system at a distance, you must use a telephone with tone dialing to call the system.
Remote access is possible only on lines that your installer programs to auto-answer calls.
To use features on a remote system, press • followed by the feature code. When you are calling
from within Business Communications Manager, press • instead of ≤.
In some conditions, you can experience lower volume levels when using the system from a
distance.
Tones
You can hear some of the following tones when accessing Business Communications Manager
Table 8 Tones and what they mean
Tone
What it means
System dial tone
Stuttered dial tone
Busy tone
You can use the system from a distance.
Enter your COS password.
You have dialed a busy line pool access code. You hear system dial tone
again after 5 seconds.
Fast busy tone
You have done one of the following:
Entered an incorrect COS password. Your call disconnects after five
seconds.
Taken too long while entering a COS password. Your call disconnects after
five seconds.
Tried to use a line pool or feature not permitted by your Class of Service.
You hear system dial tone again after five seconds.
Dialed a number in the system which does not exist.Your call disconnects
after five seconds.
Voice mail
If you subscribe to Voice Messaging, you can access that service through Business
Communications Manager. A software keycode is required for Voice Messaging. Your installer
programs your telephone to indicate when you have a voice message waiting on a specific line.
When you select an extension number from the Terminals & Sets programming level, a Mailbox
Configuration button appears. Press the button to start a Voice Applications Manager session. The
Mailbox configuration button allows you to access the Voice Applications Manager without having
to exit Unified Manager. Add the mailbox and close the window to return to the Unified Manager.
For more information about configuring a mailbox, see the Business Communications Manager
Programming Operations Guide.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 System features 113
Similarly, when you select a line number from the Lines programming level, a voice mail settings
button appears. Press the button to start a Voice Applications Manager session. The voice mail
settings button allows you to configure voice mail line settings and then continue programming
other line parameters in Unified Manager. For more information, see the Business
Communications Manager Programming Operations Guide.
Service provider features
Features from your service provider include:
•
•
•
Call Forward
Automatic Call Back
Automatic Recall
Call Forward
Call Forward allows you to forward incoming calls to an external telephone number. Ask your
service provider for the appropriate Call Forward feature code.
1
Select an ISDN line by selecting a line button, a line pool, or the Handsfree button, or by
lifting the handset (if an ISDN line is your prime line).
2
3
Enter the Call Forward feature code. Listen for three tones followed by dial tone.
Enter the number of the telephone where you want to forward your calls. If the call is
answered, remain on the line for at least five seconds to activate the Call Forward feature.
Cancel Call Forward
1
Select an ISDN line by selecting a line button, a line pool, or the Handsfree button, or by
lifting the handset (if an ISDN line is your prime line).
Enter the feature code to cancel Call Forward. Listen for a series of tones.
Press ®.
2
3
Call the number where your calls are forwarded
1
Select an ISDN line by selecting a line button, a line pool, or the Handsfree button, or by
lifting the handset (if an ISDN line is your prime line).
2
Enter the feature code.
Automatic Call Back
If you call a number and it is busy, enter the appropriate feature code assigned by your service
provider to receive ringing notification when the line becomes available. The Automatic Call Back
ring type is different from your normal telephone ring type.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
114 Chapter 12 System features
Automatic Recall
Automatic Recall allows you to automatically dial the number of the last call you received.You
cannot see the number on the display if the information is not available from your service provider,
or when you do not have Caller ID in your ISDN service. Ask your service provider for the
appropriate feature code.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
115
Chapter 13
Hospitality Services
Hospitality Services (HS) is a group of features that increases the value of Business
Communications Manager. The Hospitality Services feature is used in small to medium sized
facilities such as hotels, motels, or hospitals.
In a hotel setting, guests gain improved services through immediate access to basic functions such
as:
•
•
wake-up service or reminders
accurate tracking of the room’s service requirements
Types of telephone set
Telephones in your system are assigned as one of three types of sets:
•
•
•
common set
room set
Hospitality Services (HS) admin set.
Common set
A common set can be a telephone found in a lobby, office, or common area not associated with a
room. A common set does not have access to all of the HS features.
Room set
You need to start a Unified Manager session to assign a Room set to a room.You can assign up to
five sets to the same room which then share the same room number. For more information about
programming using Unified Manager, see the Business Communications Manager Programming
Operations Guide.
Hospitality Services (HS) admin set
A Hospitality Services (HS) admin set is any two-line display telephone in the system. You can
program an HS admin set to require a user to enter the Desk admin password before accessing HS
admin features. For more information about programming an admin set, see the Business
Communications Manager Programming Operations Guide.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
116 Chapter 13 Hospitality Services
Alarm time (AL) feature
The Alarm time feature provides an alarm clock capability on both room sets and common sets
which can be programmed to sound an audible alert at a requested time.
One Alarm time within a 24 hour period is programmable on a room or common set and must be
reset daily. When the alarm sounds, all sets in a given room ring. If you cancel the alarm on any
set, it cancels the alarm on all the sets in the room. A new Alarm time entered on a room or
common set overwrites any alarms previously assigned.
If the system experiences a power failure, this can result in missed Alarm times. When the system
is running and the system time resets, the missed Alarm times ring in respective room or common
sets. The system allows a maximum of 25 sets with alarms.
Program the Alarm time feature
To program the Alarm time feature on a telephone:
1
2
Press ≤°‡fi.
The display shows Alrm: 07:00am OFF. If the alarm time is correct press ON.
The display shows Alrm:07:00am ON.
Press DONE to exit.
or
To enter a new alarm time press CHG. The display shows Enter time:. Enter a new 4 digit alarm
time.
When using the 24 hour clock format (hour: 00 to 23 and minutes: 00 to 59), no confirmation is
required. The display shows Alarm ON hh:mm.
When using the 12 hour format, the display shows hh:mm AM or PM?. Press the AM or PM display
button. The display shows Alarm ON hh:mm.
To program the Alarm time feature on an analog telephone:
1
2
Press ≤•°‡fi. A tone sounds.
Enter a 4 digit alarm time.
When using the 24 hour clock format (hour: 00 to 23 and minutes: 00 to 59), a tone sounds.
When using the 12 hour format, press • to select am, or £ to select pm. A tone sounds.
At the assigned times, the set in the room rings to wake-up or remind the occupant of the next
event or meeting.
Change or cancel an Alarm time
When you enter a new Alarm time it overwrites any times previously assigned. If you cancel the
Alarm time for any set, it cancels the Alarm time for all the sets in the same room.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 Hospitality Services 117
Cancel an alarm
•
Press ≤£°‡fi to cancel the Alarm time on a telephone with a display.
The display shows Alarm OFF.
•
Press û£°‡fi to cancel the Alarm time on an analog telephone.
Turn off an Alarm
To release a ringing alarm:
•
•
On a telephone with a display, press any button except the ≥ button.
On an analog telephone, lift the handset and then hang up.
Note: If the user presses the ≥ button when the set rings, it temporarily
deactivates the Alarm. After a number of minutes, the set will ring again.
If the user is on a call when the alarm rings, press any button except ® to
cancel the alarm and maintain the active call.
Hospitality Services admin alarm feature
Only a Hospitality Services (HS) admin set can use the Hospitality Services admin alarm feature.
The Hospitality Services admin alarm feature is room oriented only. It does not control the alarms
on common sets.
The Hospitality Services admin feature can:
•
•
determine the current or last alarm time set for a room
overwrite previous Alarm time programming for a room in the system
— assign an Alarm time for any room
— change an Alarm time for any room
— cancel an Alarm pending for any room
To program the Alarm time for a room with the Hospitality Services admin alarm feature:
1
2
3
4
Press ≤°‡‡ on a T7316 or M7324(N) two-line display telephone.
If configured, the display shows Password:. Enter the Desk admin password.
The display shows Al of rm#:. Enter the room number and press OK.
Press VIEW. The display shows Alrm: 07:00am OFF:. If the alarm time is correct press the ON/OFF
display button to activate the alarm.
5
Enter a four-digit alarm time.
If the 24 hour format is used (hour: 00 to 23 and minutes: 00 to 59), no confirmation is
required. The display shows Alarm hh:mm ON.
If the 12 hour format is used, the display shows the four digit time plus AM or PM?. Press the AM
or PM display button. The display shows Alarm hh:mm am ON or Alarm hh:mm pm ON.
6
Press the ® button to exit programming.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
118 Chapter 13 Hospitality Services
Room occupancy
The Room occupancy (RO) feature allows front desk operators to assign dialing restrictions to
room sets, and works with the Room condition (RC) feature. The RO feature does not apply to
common sets. Dialing restrictions for room sets are defined in Unified Manager. For more
information, refer to the Business Communications Manager Programming Operations Guide.
The RO feature uses the following room states: Vacant filter, Basic filter, Mid filter, and Full filter.
A variety of dialing filters can be configured for each room state. The default setting is Vacant.
•
•
•
•
Vacant — Room is empty.
Basic — Room is occupied.
Mid — Room is occupied.
Full — Room is occupied.
Programming the state of a room set
To access the Room Occupancy feature and assign the state of a room set:
1
2
3
4
Press ≤°‡· on a T7316 or M7324(N) two-line display telephone.
If configured, the display shows Password:. Enter the Desk admin password.
The display shows Oc of rm#:. Enter the room number and press OK.
The display shows rrrrr:Vacant. Press the CHANGE display button and select the required status
for the room set: Vacant, Basic, Mid or Full. The default setting isVacant.
5
To program other rooms, press the FIND or NEXT display button and return to step 3.
If no more rooms require programming, press the ® button to exit programming.
Note: Programming a room to Vacant state cancels any outstanding alarms.
Room condition
The Room condition (RC) feature allows users to exchange information about the serviced state of
a room. Users are front desk attendants, and cleaning or maintenance personnel of an
establishment. The RC feature is not available from a common set.
The system maintains a database of the state of each room. This database is accessed from either
the room set or a Hospitality Services admin set.
Room sets can:
•
•
•
assign the associated room state to Service done (Srvc done)
assign the associated room state to Needs service (Needs srvc)
query the state of the associated room on a set with a display
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 Hospitality Services 119
Front desk sets can:
•
•
•
assign any room state to Service done (Srvc done)
assign any room state to Needs service (Needs srvc)
query the state of any room
The system changes the state of occupied rooms to Needs service on a daily basis at a time
assigned in configuration.
Maintenance personnel change the condition of the room to Service done when service in the room
is complete.
The front desk attendant can query or program the condition of a room with a Hospitality Services
admin set. The system automatically assigns the status of a room to Needs srvc, when a room
occupancy status changes from occupied to vacant.
Room condition from a room set
To update the room condition using a room set:
1
Press ≤°‡fl on a two-line display telephone or press û¥¡àß on an
analog telephone.
2
3
At the prompt, enter the status of the room.
Press ⁄ on the dialpad to indicate Set to srv done.
If required, enter the room condition password.
or
Press ¤ on the dialpad to indicate Set to needs srv.
If required, enter the room condition password.
4
The display shows Set to srv done or Set to needs srv.
Room condition with a Hospitality service admin set
To update or query the room condition using a HS admin set:
1
2
Press ≤°‡° on a T7316 or M7324(N) two-line display telephone.
If configured, the display shows Password:.
Enter the desk admin password.
3
4
The display shows Cd of rm#:.
Enter the room number and press OK.
The display shows rrrrr:Vacant.
Press the CHANGE display button and select the required status for the room set:
•
•
If the room is occupied, select Srvc done or Needs srvc.
If the room is vacant, select Vacant or Needs srvc.
The default setting is Vacant.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
120 Chapter 13 Hospitality Services
5
To update or query other room set, press the FIND or NEXT display button and return to step 3.
If there are no more room sets updates or queries, press the ® button to exit programming.
Hospitality passwords
The Hospitality Services feature allows for two types of passwords to access different areas of
Hospitality programming.
Desk admin password
Use the Desk password to access all Hospitality Services admin features. The default desk
password is: ÓØÍ∏ (4677). You need to start a Unified Manager session to program to
changes the default desk password. For more information about programming using Unified
Manager, refer to the Business Communications Manager Programming Operations Guide.
Room condition password
The room condition password controls the ability to change the room condition using
≤°‡fl. The default room condition password is None. The room condition password may
remain as None.
To change the default room condition password you need to start a Unified Manager session. For
more information about programming using Unified Manager, refer to the Business
Communications Manager Programming Operations Guide.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
121
Chapter 14
Portable telephone and handset features
There are three portable telephones supported by Business Communications Manager: the
Companion C3050 Etiquette, Companion C3060 Portable, and the Companion C3050 CT2Plus.
There are two portable handsets supported by Business Communications Manager: the DECT
C4010 Handset, and the DECT C4020 Handset. These handsets have region-based availability. For
more information about DECT, refer to the Business Communications Manager DECT Installation
and Maintenance Guide.
Portable telephones
Your portable telephone communicates with Business Communications Manager using radio
waves. The radio transceivers for the system are located in the base stations installed at your office.
Each base station contains two radio transceivers and can handle two portable telephone calls at
the same time.
Not only can you start a telephone conversation anywhere in the office, you can continue that
conversation while you walk throughout the building. As you move from one part of your office to
another, your call passes from one base station to the next.
If there is a decrease in voice quality while you are moving with a portable telephone, you may be
moving out of range from your system base stations. There are three possible reasons for this:
•
•
•
The base stations that cover the area you are moving into are busy or unable to pick up your
call.
Large pieces of furniture or movable partitions block the signal between you and the base
station.
You have moved out of the range covered by your system.
(Retrace your steps until you are back in range.)
In rare instances, during a Message session, softkey display prompts on your portable may
disappear. This is a normal condition and is improved by staying within range of a base station.
While you are moving within range, you may hear a slight clipping during a call. Clipping occurs
as a call is handed off from one base station to the next.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
122 Chapter 14 Portable telephone and handset features
Problems with lost connections are rare, but if you notice an increase in occurrences, your base
stations may need to be moved or reprogrammed. Contact your installer to change the base station
configuration. (In the U.S. you need to obtain UTAM Inc. approval before making changes to the
base station configuration.) For more information, refer to Business Communications Manager
Programming Operations Guide.
Note: If you try to send a message from a desk telephone to a portable telephone,
the display of the desk telephone shows CanÕt send msg.
Portable telephone features
It is possible to use many of the same system features available to a Business Communications
Manager telephone on your portable telephone. The table below shows the features available for
use on a portable telephone. For more information about features and the special codes required to
use them, refer to the feature card that came with your portable telephone. Table 9 shows the
Table 9 Features available to a portable telephones in the system
Feature
Description
Call Forward
Send calls to another telephone in your system. The display does not indicate
that calls are being forwarded. Hunt Group calls override all Call Forward
features. A Hunt Group extension can be a Call Forward destination.
Call Information
The display shows the name or extension of an internal caller. If your system is
equipped to receive CLASS information (Caller ID), the external call information
appears on the display.
Call Park
Park a call.
Call Park Retrieval
Cancel Call Forward
Retrieve a parked call.
Cancel the Call Forward feature, where calls are automatically sent to another
telephone in the system.
Conference
Create a three-way call.
Directed Call Pickup
Group Pickup
Host system signaling
Line Pool
Answer any telephone that is ringing in the system.
Answer a call ringing on another set within the same pickup group.
Use link and pause.
Use line pools the same way a desk telephone does.
Mute
Prevent other callers from hearing you. Also, you can mute incoming calls from
ringing on a portable telephone.
Page
Page an individual telephone, several telephones, external speakers, or the
entire system. A Hunt Group extension cannot be in a page zone.
Pause
Program an external autodial sequence to insert a 1.5 second delay.
Prime line
On your portable, this may be either an Intercom Line, an Assigned Line or a
Line Pool.
Privacy
In programming, change the privacy setting for an external line assigned to the
portable. This does not give the ability to change the privacy setting on a call by
call basis.
Release
End a call or programming session.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 Portable telephone and handset features 123
Table 9 Features available to a portable telephones in the system
Feature
Description
Speed Dial
System speed dial codes only. No personal speed dial codes. The portable
directory can store up to 50 telephone numbers.
Switching between two
calls
Put one call on hold and speak to another caller.
Transfer
Transfer a call to another telephone.
Transfer using directory
Trunk Answer
Transfer a call using your portable telephone directory.
Answer a ringing call for lines placed in a Service Mode.
Wireless Portable
Language Selection
Change the language of the prompts that appear on the portable telephone
display.
Wireless Call Forward No Forward a call without ringing. The portable user can answer a call but it does
Answer
not ring.
Directed Call Pickup
You must enable the Directed Call pickup feature before it can be used. For more information
about the Directed Call pickup feature, refer to the Business Communications Manager
Programming Operations Guide.
Group Pickup
Group Pickup allows the portable user to answer a call ringing on another telephone within the
same pickup group. For more information, refer to the Business Communications Manager
Programming Operations Guide.
Wireless Portable Language Selection
This feature allows you to change the language of the voice prompts and the prompts that appear
on the portable telephone display.
The system supports a primary default language and three alternate languages.
Press ••fi‚⁄
Press ••fi‚¤
Press ••fi‚‹
Press ••fi‚›
Language - Primary
Language - Alternate
Language - Alternate 2
Language - Alternate 3
Wireless Call Forward No Answer enhancement
This feature prevents a portable telephone from ringing when the call is forwarded to a new
destination. The portable user can answer the call, even though it does not ring. For more
information, refer to the Business Communications Manager Programming Operations Guide.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
124 Chapter 14 Portable telephone and handset features
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
125
Chapter 15
Troubleshooting
This chapter describes alarm codes and how to use them. It also show you how to test your
telephone.
Alarm codes
An alarm telephone display shows Business Communications Manager system alarm codes when
they occur. The installer assigns alarms to T7316 or M7324(N)two-line display telephones.
Report and record alarm codes
If an alarm message appears on the alarm telephone display:
1
2
Record the alarm number.
Call your customer service representative and report the alarm code.
Alarm:
TIME
61-4-2
Report this alarm and the time it occurred to your installer or
customer service representative.
Note: Alarms are also stored in the WinNT Network Event log. For more
information, see the Business Communications Manager Programming
Operations Guide.
Test the telephone
If you know something is wrong with a button, the speaker, the displays, or some other part of the
telephone hardware, you can do a quick test to see which part of the telephone is not functioning
properly.
Test the telephone display
To test the telephone display:
1
2
3
Press ≤°‚fi. The display shows Display test.
Press TEST.
Adjust the contrast level for the telephone display so you can clearly see the test results. The
contrast level ranges from one to nine. Enter a number to change the contrast or press DOWN and
UP.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
126 Chapter 15 Troubleshooting
4
Press OK or ≤ to go ahead with the test.
During the test, the display shows solid, dark blocks and all the indicators next to the buttons
on the telephone. Any Busy Lamp Field (BLF) or CAP modules connected to the telephone
must be completely lit. You lose any information which appeared on the BLF before the test
started.
5
Press any button to end the test.
Test the telephone buttons
To test the telephone buttons:
1
2
3
Press ≤°‚fi. The display shows Display test.
Press NEXT. The display shows Button test.
Press TEST. Press each button to determine its function. If the button you pressed uses an
indicator, it must light when you test the button.
4
When you press the ® button, Rls button appears on the display. Press ® again to end
this test.
Test the speaker in the telephone handset
The handset test is not available when a headset is plugged into the telephone.
1
2
3
Press ≤°‚fi and NEXT twice. The display shows Handset test.
Press TEST.
Pick up the handset and listen. You can hear dial tone through the handset at a maximum
volume. The volume is reset to maximum only while the test is in progress.
4
Press any button to end the test.
Test the telephone headset
The headset test is only available to telephones with a headset.
1
2
Press ≤°‚fi and NEXT until the display shows Headset test.
Press TEST. You hear dial tone through the headset. The volume resets to the default level
during this test.
3
Press any button to end the test.
Test the telephone speaker
To test the telephone speaker:
1
Press ≤°‚fi and NEXT until the display shows Speaker test.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 Troubleshooting 127
2
3
Press TEST.
You hear a page tone through the telephone speaker at the maximum volume. The volume
returns to its previously assigned level at the end of the test.
Press any button to end the test.
Test the power supply to a telephone
1
2
Press ≤°‚fi and NEXT until the display shows Power test.
Press TEST.
All the indicators on the telephone light and the telephone rings at maximum volume. When
the test ends, the display shows Power OK. The test continues for five seconds or until you press
a button.
Note: Make sure the function of a button matches the label by pressing
≤•‚and then the button. Press ® to end the telephone testing session.
The test feature times out after three minutes of inactivity.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
128 Chapter 15 Troubleshooting
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
129
Appendix A
Feature Codes
This appendix provides a quick reference for Business Communications Manager features
available by pressing the ≤ button and entering a code. Table 10 provides feature names sorted
Table 10 Features sorted by feature name
Feature name
Activation code
ACD agent login/log out
ACD agent make busy/ready
ACD queue status
≤·‚›
≤·‚°
≤·‚·
Alarm time
≤°‡fi
≤£°‡fi
≤°‡‡
≤•⁄
Alarm time - Cancel
Alarm time (HS admin set)
Autodial - External
Autodial - Internal
≤•¤
Background Music
≤°fl
Background Music - Cancel
Button inquiry
≤£°fl
≤•‚
≤°⁄°
Call Charge Indication
Call Duration Timer
Call Forward
≤‡‡
≤›
Call Forward - Cancel
≤£›
≤·°›
Call Forward to Voice Mail
Call Information
≤°⁄⁄
≤°⁄fi
≤°⁄‹
≤°⁄¤
≤•°›
≤•°fi
≤‡›
Call Log - Delete items (Auto Bumping)
Call Log - Manual
Call Log - View information
Call Log options
Call Log password
Call Park
Call Queuing
≤°‚⁄
≤°¤
Camp-on
Class of Service
≤fl°
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
130
Feature Codes
Table 10 Features sorted by feature name (Continued)
Feature name
Conference Call
Contrast adjustment
Dialing Mode
Activation code
≤‹
≤•‡
≤•°¤
≤‡fl
≤·°fi
Directed Pickup
Display Voice Mail DN
Do not Disturb
≤°fi
Do not Disturb - Cancel
Exclusive Hold
≤£°fi
≤‡·
≤·°‚
Express Messaging
Group Listening
≤°‚¤
≤£°‚¤
≤‡fi
Group Listening - Cancel
Group Pickup
Language - Primary1
Language - Alternate1
Language - Alternate 21
Language - Alternate 31
Last Number Redial
Line buttons - Move
Line Pool
≤•fi‚⁄
≤•fi‚¤
≤•fi‚‹
≤•fi‚›
≤fi
≤•°⁄
≤fl›
Line Redirection
≤°›
Line Redirection - Cancel
Link
≤£°›
≤‡⁄
Long tones
≤°‚°
≤°·‡
Malicious call identification (MCID)
Memory buttons - Program
Messages - Send
≤•‹
≤⁄
Messages - Cancel Send
Messages - View
≤£⁄
≤flfi
≤°⁄·
≤£°⁄·
≤fl‚
≤fl‹
≤fl¤
Name and number blocking
Name and number blocking - Cancel
Page
Page - Combined (internal & external)
Page - External (external speakers)
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Codes 131
Table 10 Features sorted by feature name (Continued)
Feature name
Activation code
Page - Internal (telephone speakers)
Pause
≤fl⁄
≤‡°
Priority Call
≤fl·
Privacy (on/off)
≤°‹
Ring Again
≤¤
Ring Again - Cancel
Ring Type
≤£¤
≤•fl
Ring Volume
≤•°‚
≤°‚‡
≤°‡fl
≤°‡°
≤°‡·
≤•·
Ringing (Signal) Call
Room condition (Room set)
Room condition (HS admin set)
Room occupancy
Run/Stop
Saved Number Redial
Speed Dial - Add, change
Speed Dial - Activate
Static Time
≤fl‡
≤•›
≤‚
≤°‚fl
≤£°‚fl
≤°‚fi
≤°‚‹
≤‡‚
Static Time - Cancel
Test telephone display
Time
Transfer
Transfer - Cancel
≤£‡‚
≤·°fl
Transfer to mailbox
Trunk Answer
≤°‚‚
≤£°‡¤
≤°‡¤
≤£°‡⁄
≤°‡⁄
≤£°‡‹
≤°‡‹
≤°‡‚
≤flfl
Turning Restriction service off
Turning Restriction service on2
Turning Ringing service off
Turning Ringing service on
Turning Routing service off
Turning Routing service on2
View active services
Voice Call
Voice Call Deny
≤°°
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
132
Feature Codes
Table 10 Features sorted by feature name (Continued)
Feature name
Activation code
Voice Call Deny - Cancel
≤£°°
≤·°‡
≤·°⁄
≤·°¤
Voice Mail Interrupt
Voice Mail login
Voice Mail Operator settings
Wait for dial tone
Notes
≤°‚›
1 For the Companion C3050 Etiquette, C3060 Portable, and C3050 CT2Plus
portable telephones, enter •• followed by the numeric code to activate this
feature.
2Contact your System Administrator for the Service control password.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Codes 133
Features sorted by activation code
Table 11 Features sorted by activation code
Activation code
≤‚
Description
Speed Dial - Activate
Button inquiry
≤•‚
≤⁄
Messages - Send
Messages - Cancel Send
Autodial - External
Ring Again
≤£⁄
≤•⁄
≤¤
Ring Again - Cancel
Autodial - Internal
Conference Call
Memory buttons - Program
Call Forward
≤£¤
≤•¤
≤‹
≤•‹
≤›
Call Forward - Cancel
Speed Dial - Add, change
Last Number Redial
Ring Type
≤£›
≤•›
≤fi
≤•fl
≤•‡
≤•·
≤fl‚
≤fl⁄
≤fl¤
≤fl‹
≤fl›
≤flfi
≤flfl
≤fl‡
≤fl°
≤fl·
≤‡‚
≤£‡‚
≤‡⁄
≤‡›
Contrast adjustment
Run/Stop
Page
Page - Internal (telephone speakers)
Page - External (external speakers)
Page - Combined (internal & external)
Line Pool
Messages - View
Voice Call
Saved Number Redial
Class of Service
Priority Call
Transfer
Transfer - Cancel
Link
Call Park
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
134
Feature Codes
Table 11 Features sorted by activation code (Continued)
Activation code
≤‡fi
Description
Group Pickup
Directed Pickup
Call Duration Timer
Pause
≤‡fl
≤‡‡
≤‡°
Exclusive Hold
≤‡·
Ring Volume
≤•°‚
≤•°⁄
≤°¤
Line buttons - Move
Camp-on
Dialing Mode
≤•°¤
≤°‹
Privacy (on/off)
Line Redirection
Line Redirection - Cancel
Call Log options
Do not Disturb
≤°›
≤£°›
≤•°›
≤°fi
Do not Disturb - Cancel
Call Log password
Background Music
Background Music - Cancel
Voice Call Deny
Cancel Voice Call Deny
Language - Primary1
Language - Alternate1
Language - Alternate 21
Language - Alternate 31
Trunk Answer
≤£°fi
≤•°fi
≤°fl
≤£°fl
≤°°
≤£°°
≤•fi‚⁄
≤•fi‚¤
≤•fi‚‹
≤•fi‚›
≤°‚‚
≤°‚⁄
≤°‚¤
≤£°‚¤
≤°‚‹
≤°‚›
≤°‚fi
≤°‚fl
≤£°‚fl
Call Queuing
Group Listening
Group Listening - Cancel
Time
Wait for dial tone
Test telephone display
Static Time
Static Time - Cancel
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Codes 135
Table 11 Features sorted by activation code (Continued)
Activation code
≤°‚‡
≤°‚°
≤£°‚·
≤°⁄⁄
≤°⁄¤
≤°⁄‹
≤°⁄fi
≤°⁄°
≤°⁄·
≤°‡‚
≤°‡⁄
≤£°‡⁄
≤°‡¤
≤£°‡¤
≤°‡‹
≤£°‡‹
≤°‡fi
≤£°‡fi
≤°‡fl
≤°‡‡
≤°‡°
≤°‡·
≤°·‡
≤·‚›
≤·‚°
≤·‚·
≤·°‚
≤·°⁄
≤·°¤
≤·°›
≤·°fi
≤·°fl
Description
Ringing (Signal) Call
Long tones
Name and number blocking - Cancel
Call Information
Call Log - View information
Call Log - Manual
Call Log - Delete items (Auto Bumping)
Call Charge Indication
Name and number blocking
Viewing active services
Turning Ringing service on
Turning Ringing service off
Turning Restriction service on2
Turning Restriction service off
Turning Routing service on2
Turning Routing service off
Alarm time
Alarm time - Cancel
Room condition (Room set)
Alarm time (HS admin set)
Room condition (HS admin set)
Room occupancy
Malicious call identification (MCID)
ACD agent login/log out
ACD agent make busy/ready
ACD queue status
Express Messaging
Voice Mail login
Voice Mail Operator settings
Call Forward to Voice Mail
Display Voice Mail DN
Transfer to mailbox
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
136
Feature Codes
Table 11 Features sorted by activation code (Continued)
Activation code
Description
Voice Mail Interrupt
≤·°‡
Notes
1 For the Companion C3050 Etiquette, C3060 Portable, and C3050 CT2Plus
portable telephones, enter •• followed by the numeric code to activate this
feature.
2Contact your System Administrator for the Service control password.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
137
Appendix B
Common display prompts and error messages
The following display prompts and error messages can appear when using a telephone connected
to Business Communications Manager.
Access denied
Programming is busy, or the feature you are trying to use is not
compatible with the configuration of the telephone or line.
Denied in admin
You are trying to use a feature, but do not have access to it under
administration.
Feature timeout
You took more than 15 seconds to press a button in response to a
display.
Inactive feature
You entered the feature code for an application that is disabled.
Invalid code
You entered an invalid feature code.
Not available
You tried to use a feature that is currently not available from your
system.
Set locked
You cannot use the feature you selected because your telephone is
1234567890123...
VIEWâ
Press £ or press VIEWâ or áVIEW to view a number that is too long
to fit on the display. Press OK when you have finished.
OK
¤
This indicates a long distance call. (May be available with Call
Display services.)
239>221
You are receiving an internal call from extension239 forwarded by
extension221, or you have an Answer button for extension221 and
an internal call from 239 is ringing on 221.
221
TRANSFR
You are connected to an internal call. Press TRANSFR to transfer the
call.
221 calling
You are receiving a call from extension 221.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
138
Common display prompts and error messages
Call 221?
YES
You have received a Ring Again offer from a call to an internal
telephone. Press the flashing internal line button or YES to call the
number again. On the T7100 telephone, just lift the handset.
Otherwise, press NO or wait 30 seconds for the Ring Again offer to
NO
Camped: 221
CALLBCK
The person at extension 221 has not answered the camped call.
The call has come back to you. Press the line button or CALLBCK to
reconnect to the call.
Line061
TRANSFR
You are connected to an external call. Press TRANSFR to transfer the
call.
Line061>221
You are receiving an external call forwarded from extension221,
or you have an answer button for extension221 and an external call
is ringing on that telephone.
Line061 transfer
Line061 waiting
No calls waiting
No line selected
Not in service
Another user in the system is transferring a call to you on line 061.
A camped call is waiting. Press the line button or use Call
Queuing to answer the call. Press ≥ if you have a T7100
telephone.
You tried to use Call Queuing but no call was ringing at your
telephone.
There is no call ringing at your telephone. If you have a flashing
line button but your telephone is not ringing, press the line button
to answer the call on that line.
The telephone where you directed a call is not in service or is or
unavailable. The call returns to your telephone.
Parked call
CALLBACK
No one answered the call you parked. The call returns to you.
Pick up receiver
You have used the Call Queuing feature without picking up the
handset. Auto Handsfree is not been assigned to your telephone.
You must use the handset or press the handsfree button to answer a
call.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Common display prompts and error messages 139
Priority> 221
BLOCK
You are receiving a priority call. If you are on another call, tell the
person you are speaking to that you are about to put the call on
hold. Press the flashing line indicator of the priority call or wait
until the call connects automatically (in eight seconds). The
priority call goes through after you hear the next beep. Your active
call is on Exclusive Hold. It reconnects automatically when the
priority call ends (unless you transfer the priority call, in which
case you must press the line button of your original call to
reconnect). Use DND (≤°fi) or press BLOCK to reject a
priority call.
Release a call
Use line pool?
You have no free line available to receive a call. Release one of
your current calls and try again to answer the incoming call.
You received a Ring Again offer for a line pool. Press the flashing
internal line button or YES to use the line pool. On the T7100
telephone, lift the handset. Otherwise, press NO or wait 30 seconds
for the Ring Again offer to expire.
YES
NO
Hold or release
Release calls
Line in use
While on a call, you must either release the call or put the call on
hold before you can program a feature button.
You tried to use a feature while you were on a call or had calls on
hold. Release the call or calls, before using the feature.
The line is in use. Make the call using normal methods or wait
until a line is free.
No button free
Make calls first
No free lines
You tried to make, receive or pick up a call when no line button
was available. Some features require you to have a button free.
Releasing calls can free up line buttons.
The feature you tried to use requires you to be on an active call at
your telephone. This prompt also appears when information about
a call is cleared by a system reset.
All the lines or line pools available to the telephone are in use.
This prompt also appears when you try to dial an external number
or use a feature that conflicts with the lines, line pools or prime
line used by the telephone. Your installer must correct this
situation.
No line selected
In use:221
The telephone is set up to dial an external number on a prime line
but the telephone does not have a prime line. Your installer must
correct this situation.
You tried to program redirection while the feature is in use. Only
one person can program line redirection at a time.
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
140
Common display prompts and error messages
Incoming only
The line you are trying to use to redirect calls is for incoming calls
only. Select an outgoing line.
9__
QUIT
Continue entering digits. Press BKSP to delete incorrect digits.
Press £ or OK when you have finished.
BKSP
OK
Invalid number
Line denied
You entered an invalid line pool code or an invalid destination
code.
You selected a line that is private to another telephone.
Restricted call
The destination you selected for line redirection is restricted.
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
141
Index
Symbols
answering calls
Numerics
A
access
Business Communications Manager from outside the
system 110
ASM
ATA
Access denied 137
ADD 26
Autodial
Autodial full 50
automatic
Allow calls 96
allow redirect
Already joined 36, 39
Already parked 60
Automatic Call Forward
Automatic Recall
analog telephone
analog telephones
announcement
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
142 Index
B
Call Forward
BKSP 26
blocking
Business Communications Manager
telephones
Call information
busy 39, 44
Button erased 50
buttons
Call Pickup
Call(s) bumped 80
bypassing
Calling 44
Camp denied 59
Camp to 59
C
call
Call 221? 138
CANCEL 26
Call blocked 44
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Index 143
Cancel denied 74
deleting
canceling
Denied in Admin 41
Denied in admin 137
CAP (central answering position)
dial pad
dial tone
Dial voice call 76
dialing
signal
changing settings
Class of Service
Cleared>LINENAM 74
communicating in the office
Conference busy 47
direct dial telephone
Conference Call
disconnect
display
customizing your telephone
D
date and time
DND 59
DND from 32
defaults
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
144 Index
DND transfer 32
Call Log
DRT 32
Call Transfer
E
Enter code 85
Conference Call
Do Not Disturb
Feature Button
Group Listening
Enter digits 50, 52
Enter zone 70
erasing
Exchanged 90
Expensive route 40
extension numbers
external
Host System Dialing Signals
Line Redirection
Message
F
Ä
Autobumping
autodial button
Page
Background Music
Call Forward
Password
Restriction Service
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
146 Index
forwarding calls
G
I
In use SETNAME 81
Inactive feature 137
Incoming only 140
H
handling many calls at once
indicator
handset
Intercom 67
intercom
Intercom # 50
Handsfree Answerback
Invalid code 52
Invalid location 90
Invalid number 50
Invalid zone 70
headset
Hidden number 51, 54
Hidden number 40
ISDN PRI
Hold
L
Last Number Redial
limiting
host system signaling
line
Hotline
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Index 147
making calls
button
memory button
Redirection
Message denied 74
Message list 74
Line 061 waiting 138
Line hung up 59
Message to 74
Messages
Line in use 139
Line Redirection 67
Line061 callback 32
Line061 hung up 58
Line061 to prime 33
Line061 transfer 138
Messages & Calls 74, 81
Microphone muted 76
monitoring
Link
log space
Move line from 91
Move line to 91
moving
long distance call
Long Tones 109
N
Network Name Display
M
New calls begin 81
M7324(N) telephone
9_ 140
No call on 60
No call to park 60
No calls waiting 138
Make calls first 139
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
148 Index
No free lines 139
No info to log 81
No last number 51
password
No last number 40
No line to use 67
No log assigned 81
No number saved 54
No number stored 52, 74
No resume item 81
Pick up receiver 138
Pickup 36
No services ON 104
No voice call 76
Pickup denied 36
Not available 137
Please wait 44
Pool code 68
portable telephone
O
OK 26
On another call 40, 44
On hold 56
Press a line 91
Outgoing line 68
OVERRIDE 26
Press held line 47
prime
overriding
P
page
Priority denied 44
Priority>223 139
Privacy
private
zones
branch exchange, accessing from Business
dialing signals) 108
Programmed 50
programming
lines
parking a call
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Index 149
system 19
system features
telephones
Release calls 139
releasing
remote use
Restr'n 104
restricting
programming telephones
retrieval codes
retrieving
publications
ring
Q
QUIT 26
R
Ring Again? 40, 45
Ringing 104
Rate Interface
redialing
Redir by 68
Routing 104
Redirect ring
Redirectºdenied 68
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
150 Index
S
Saved Number Redial
Speed Dial
Start of list 75
Still in trnsfer 58
security
Select a line 40, 53
Select line out 68
Select line(s) 68
system
programming 19
Send message? 40
Service Modes ON 104
T
Service provider features
T7100 telephone
Service Schedules
Services
Set locked 137
SHOW 26
T7208 telephone
signal
T7310 telephone
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
Index 151
troubleshooting
testing
telephone
U
Unequipped line 68
Unknown name 80
testing
Unknown number 53
until * 104
Use line pool? 139
3 parties only 47
V
VIEW 26
time and date
viewing
Ä¡âß 74
time savers
Voice call 76
voice mail
tone
accessing your Business Communications Manager
Voice Messaging system 112
tracking incoming calls
W
Telephone Features Programming Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
152 Index
Y
Your list full 75
P0937240 02
Download from Www.Somanuals.com. All Manuals Search And Download.
|