NEC TheaterSync Video Processor
User Manual
Document No. MKT-0026-UMN-1.002F
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Table of Contents
1.1 Limited Warranty .............................................................................................................. 4
1.2 Related Documents............................................................................................................ 6
1.3 FCC Statement .................................................................................................................. 6
1.4 Safety................................................................................................................................. 7
2.1 General Description......................................................................................................... 10
3.1 List of Standard Components.......................................................................................... 14
3.2 Setting up your TheaterSync........................................................................................... 14
4 TheaterSync User Interface.................................................................................................16
4.1 IR Remote Control .......................................................................................................... 16
4.2 TheaterSync Operational Modes ..................................................................................... 17
5 On-Screen Menu...................................................................................................................22
5.1 OSM Menu Structure ...................................................................................................... 22
5.2 Aspect Ratio .................................................................................................................... 30
6 Appendix A............................................................................................................................36
NEC Solutions, Inc.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
1 Preface
1.1 Limited Warranty
NEC Solutions (America), Inc. warrants this product to be free from defects in material and
workmanship under the following terms and, subject to the conditions set forth below, agrees to
repair or replace (at NEC Solutions’ sole option) any part of the enclosed unit which proves
defective. Replacement parts or products may be new or refurbished and will meet specifications
of the original parts or products.
HOW LONG IS THE WARRANTY?
Parts and labor are warranted for (1) one year from the date of the first customer purchase.
WHO IS PROTECTED?
This warranty may be enforced only by the first purchaser.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material or workmanship in this
product. The following are not covered by the warranty:
1. Any product which is not distributed in the U.S.A. or Canada by NEC Solutions or which is
not purchased in the U.S.A. or Canada from an authorized NEC Solutions dealer.
2. Any product of which the serial number has been defaced, modified, or removed.
3. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature,
unauthorized product modification, or failure to follow instructions supplied with the
product.
b. Repair or attempted repair by anyone not authorized by NEC Solutions.
c. Any shipment of the product (claims must be presented to the carrier).
d. Removal or installation of the product.
e. Any other cause which does not relate to a product defect.
f. Burns or residual images upon the phosphor of the panel.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any accessories used in
connection with the product.
5. Service outside of the U.S.A. and Canada.
Page 4
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items, but we will not pay for the
following:
1. Removal or installation charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user controls. These
costs are the responsibility of the NEC Solutions dealer from whom the product was purchased.
3. Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you purchased the product.
2. Whenever warranty service is required, the original dated invoice (or a copy) must be
presented as proof of warranty coverage.
When mailing the request for service, always include your name, address, and a description of
the problem(s).
3. For the name of the nearest NEC Solutions authorized service center, call NEC Solutions at
800-836-0655.
LIMITATIONS OF LIABILITY
Except for the obligations specifically set forth in this warranty statement, we will not be liable
for any direct, indirect, special, incidental, consequential, or other types of damages, whether
based on contract, tort, or any other legal theory, whether or not we have been advised of the
possibility of such damages. This warranty is in lieu of all other warranties expressed or implied,
including, but not limited to, the implied warranties of merchantability or fitness for a particular
purpose.
EXCLUSION OF DAMAGES
NEC Solutions’ liability for any defective product is limited to the repair or replacement of the
product at our option. NEC Solutions shall not be liable for:
1. Damage to other property caused by any defects in this product, damages based upon
inconvenience, loss of use of the product, loss of time, commercial loss; or
2. Any other damages whether incidental, consequential or otherwise. Some states do not allow
limitation on how long an implied warranty lasts and/or do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations and exclusions may not apply to
you.
NEC Solutions, Inc.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
HOW STATE LAW RELATES TO THE WARRANTY
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
FOR MORE INFORMATION,
TELEPHONE 800-836-0655
NEC SOLUTIONS (AMERICA), INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
Note: All products returned to NEC Solutions (America), Inc. for service MUST have prior
approval. To get approval, call NEC Solutions (America), Inc. at 800-836-0655.
1.2 Related Documents
• TheaterSync Service Manual
1.3 FCC Statement
Note: This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential/office installation. The equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
• Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Page 6
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
1.4 Safety
1.4.1 Important Safety Instructions
This symbol warns the user of uninsulated voltage within the unit that can cause
dangerous electric shocks.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER. NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
This symbol alerts the user that there are important operating and maintenance
instructions in the literature accompanying this unit.
Read the User Guide carefully and completely before operating the unit. Be sure to keep the
User Guide in a near-at-hand location for future reference. Strictly follow all warnings and
cautions in this User Guide, as well as the following safety suggestions. To prevent electric
shock or injury, follow these safety instructions in the installation, use, and servicing the unit.
1.4.2 Installation
Attachments - Do not use attachments not recommended by the manufacturer, as they may result
in the risk of fire, electric shock, or injury to persons.
Water and Moisture - Do not use this unit near water; for example, near a bathtub, washbasin,
kitchen sink or laundry tub, in a wet basement, or near a swimming pool, water spa, or the like.
Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other
appliances that generate heat. Also, do not place this product in temperature environments
greater than 45oC (104oF).
Mounting Surface - If not installing the unit in a standard equipment rack using the
recommended mounting brackets, place the unit on a flat, even surface. Do not place the unit on
an unstable cart, stand, tripod, bracket, or table. The unit may fall causing serious injury to a
person and/or serious damage to the appliance.
NEC Solutions, Inc.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Portable Cart - An appliance and cart combination should be moved with extreme care. Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart combination to
overturn.
Ventilation - Locate the unit with adequate space around it so that proper heat ventilation is
assured. Allow 10 cm (4 in) clearance from the rear and top of the unit, and 5 cm (2 in) from
each side.
Slots and openings in the unit's case are provided for ventilation to ensure reliable operation of
the unit and to prevent overheating. These openings must not be blocked or covered. The
openings should never be blocked by operating the unit while placed on a bed, sofa, rug, or
similar surface. This unit should not be placed in a built-in installation such as a bookcase unless
adequate ventilation is provided.
Entry of Foreign Objects and Liquids - Never push foreign objects of any kind into this unit
through the ventilation slots as they may touch dangerous voltage points or short-circuit
electrical/electronic parts that could result in fire, or electric shock, or both. Never spill liquid of
any kind onto the unit.
Electric Power - Only operate the unit from the type of electric power source indicated on the
unit's labeling. If you are not sure of the type of power supply that is available in your home or
workplace, consult your appliance supplier or local power company.
Grounding or Polarization - This unit is provided with a 3-pin, grounded, alternating current line
plug. This plug will fit into the power outlet only one way. This is a safety feature. Do not try to
defeat the safety purpose of the plug.
Power Cord Protection - Route power supply cords so that they are not likely to be walked on or
pinched by placing items upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the product.
Overloading - Do not overload wall power outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
Lightning - For added protection for this unit during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the power outlet. This will
prevent damage to the unit due to lightning or power surges.
1.4.3 Maintenance
Cleaning - Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Only use a soft cloth dampened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzene, or paint thinner.
Damage Requiring Service - Unplug this unit from the power outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power cord or plug is damaged.
Page 8
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
• If liquid has been spilled or foreign objects have fallen into the unit.
• If the unit has been exposed to rain or water.
• If the unit does not operate normally, following the operating instructions. Adjust only
those controls that are covered by the operating instructions as improper adjustment of
other controls may result in damage and may require extensive work by a qualified
technician to restore the unit to normal operation.
• If the unit has been dropped or the case has been damaged.
• When the unit exhibits a distinct change in performance - this indicates a need for
service.
Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
NEC Solutions, Inc.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
2 Introduction
2.1 General Description
companion for plasma and projector displays. TheaterSync brings the power of Silicon Optix
HQVTM (“Hollywood Quality Video”TM) technology to viewers of plasma and projector
displays. Initially conceived in the military research labs of Lockheed Martin and then refined
and commercialized by Teranex and Silicon Optix, HQV video processing has been the
technology of choice of film and video professionals in broadcast and studio environments for
years. A breakthrough in cost reduction and packaging now enables this revolutionary
technology - previously found only in Professional Post Production, Film Editing and Broadcast
Studios – to be delivered to your home or business viewing environment.
Figure 1: NEC TheaterSync Video Processor
As a video signal processor, TheaterSync receives the video signals generated by a wide variety
of consumer electronic and professional devices, switches between them, and applies HQV
appropriate resolution and aspect ratio of the plasma panel, projector, or other display device.
HQV signal processing includes the following powerful features:
• State-of-the-art, motion-adaptive de-interlacing for both SDTV and HDTV
• Temporal Recursive Noise Reduction
• Codec Noise Reduction (includes mosquito noise reduction and block artifact removal)
• Detail Enhancement
• Fully-automatic detection and correction for multiple film/video cadences (3:2, 2:2, vari-
speed, 6:4, 8:7, etc.)
• AnyPlaceTM technology for extreme off-axis keystone correction
• Brightness-Contrast Enhancement
• Color Space Conversion and Color Temperature Adjustment
Page 10
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Figure 2: Typical TheaterSync Application
TheaterSync also performs a number of useful signal processing functions such as high-quality
video scaling, switching, extreme keystone correction and audio delay, thus eliminating the
requirement for stand-alone scalers or audio delay units within your system.
TheaterSync offers access to a truly wide range of signal inputs – everything from SDTV
(composite, S-Video and component) to HD-SDI and all popular video and computer graphics
signals in between (including analog RGB, DVI, and HDMI) may be selected as inputs.
TheaterSync provides video output in HDMI, DVI and analog RGB formats on dedicated
connectors.
All this functionality can be controlled through a simple 20-button IR remote control unit (see
Menu). Video input device selection is accomplished using dedicated IR remote buttons.
Access to the HQV features is also provided through dedicated IR remote buttons. Also,
TheaterSync provides the professional user with flexible control methodologies of RS-232, USB
and Ethernet. For details on the control programming protocol, refer to the TheaterSync Service
Manual.
The TheaterSync video processor is available in a compact and attractive desktop package that
can be rapidly fitted to a standard 19” rack using a rack mounting kit (included).
NEC Solutions, Inc.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Features and Specifications
Input Video Signals
¾ Composite Video (NTSC, PAL and SECAM)
¾ S-Video (NTSC and PAL)
¾ Component (YPbPr for SDTV and HDTV in American and European formats)
¾ Analog RGB (VGA to SXGA60Hz)
¾ DVI (VGA to QXGA)
¾ HDMI
¾ SDI (including HD-SDI and audio)
Output Video Signals
¾ Analog RGB (VGA to UXGA)
¾ DVI (VGA to QXGA)
¾ HDMI
Input Audio Signals
¾ S/PDIF
¾ Toslink
¾ HDMI
Output Audio Signals
¾ S/PDIF
¾ Toslink
¾ HDMI
Video and Audio Processing Capability
¾ Scaling
¾ Extreme Keystone Correction (+/- 40o horizontal, +/- 30o vertical)
¾ Audio Delay
¾ Input Switching
¾ Aspect Ratio Correction
¾ HQV Video Processing …
• Temporal-Recursive Noise Reduction
• Codec Noise Reduction
• Fully-automatic cadence detection and correction
• Detail Enhancement
• Advanced motion-adaptive de-interlacing
Control
¾ IR Remote Control
¾ RS-232
¾ USB (for connection to Crestron / AMX boxes)
¾ Ethernet
Page 12
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Physical Characteristics
Dimensions: 17.0” x 9.7” x 1.75” (43.2 x 24.6 x 4.4 cm)
Weight:
Power:
7 lbs. (3.2 kg)
100-240V, 47-63 Hz, 72W
Panel Diagrams
Figure 3: TheaterSync Front Panel Drawing
Figure 4: TheaterSync Rear Panel Drawing
NEC Solutions, Inc.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
3 Installation
3.1 List of Standard Components
The TheaterSync processor ships with a number of standard components. When unpacking your
unit, verify that the following items are included:
• TheaterSync unit (qty 1)
• IEC-320 American AC power cord (qty 1)
• Infrared remote control (qty 1)
• Rack-mount adapter kit (qty 1)
• TheaterSync User Manual (qty 1)
3.2 Setting up your TheaterSync
To set up your TheaterSync unit, follow the steps below:
1. Connect the TheaterSync unit to the video input sources.
2. Connect the TheaterSync unit to the display device.
NOTE: If you are connecting to a panel or projector that supports the coding of HDCP
encrypted material on its DVI input, you must connect to that DVI input using TheaterSync’s
HDMI OUT connector (and an HDMI to DVI adapter).
3. To power up the unit, press the Power switch located on the rear of the unit, close to the
power cord. The Power switch may be left on in normal operation. The On/Setup button
on the front panel may be used to put the unit into a low-power state (Setup Mode).
NOTE: When TheaterSync is in Setup (Stand-by) Mode, the output to the projector or panel is
temporarily suspended.
4. Select the output resolution to match the native resolution of the display device:
a) Place the unit in Setup (Stand-by) Mode by toggling the Operate/Setup button on the
IR remote (or by using the On/Setup button on the unit’s front panel).
b) Using the up/down arrow keys of the remote, cycle through the different setup modes
(which will be displayed on the box LCD display) until the output resolution mode is
selected (“OUT = xxx” will appear on the LCD display, where ‘xxx’ is the current
active output resolution)
c) Using the left/right arrow keys, select the desired output resolution.
5. Return TheaterSync to Operate Mode by pushing the On/Setup button on the front panel
or the Power button on the IR Remote. This activates the TheaterSync output circuits.
Further adjustments may be made using the TheaterSync OSM (On-Screen Menu).
Page 14
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
For projection applications where keystone correction is required, continue with the following
steps:
6. If the projector has an AUTOSET or AUTODETECT feature, disable this function.
These projector modes may cause image distortion if a keystone-corrected image is
applied to the projector input.
7. Select the “Advanced” menu from the TheaterSync OSM, then select “Projection”, and
“Horizontal and Vertical Keystone” submenus.
8. Using the up/down arrow keys, select in turn each of the image corner sliders and then
use the left/right arrow keys to move the corner to the desired location on the screen.
Continue adjustments until the projected image matches the target screen geometry.
NEC Solutions, Inc.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
4 TheaterSync User Interface
4.1 IR Remote Control
All TheaterSync user interface controls are accessed via infrared (IR) remote control. The
remote has three groups of controls:
a) OSM Navigation (including the Operate/Setup Key),
b) Video Source Selection, and
c) HQV Feature Selection.
You may also select video sources and HQV processing features through the OSM navigation
controls, however dedicated IR remote keys provide you with quick one-touch access to the most
Figure 5: TheaterSync Remote Control
A description of the various buttons and their functions is as follows:
Page 16
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
The Operate/Setup button toggles the TheaterSync between “Operate” and “Setup” modes of
operation (as described in the next section of this User Interface chapter).
The Menu button is used to invoke the OSM main menu.
The Up/Down/Left/Right Arrow buttons are used to navigate the OSM.
The Enter/Select button is used to activate an OSM menu selection.
Direct (one-touch) input selection is possible using the buttons below:
• The RGB button selects the VGA port as the active input.
• The DVI button selects the DVI port as the active input.
• The Video button selects the composite video port as the active input.
• The S-Video button selects the S-Video port as the active input.
• The YPbPr button selects component video as the active input.
• The HDMI button selects HDMI as the active input.
• The SDI button selects the SDI port as the active input
Additional buttons are available to directly access key video processing features and to cycle
through the available enhancements:
• The BCE button activates/deactivates the Brightness / Contrast Enhancement feature
• The Aspect Ratio button cycles through and selects the available aspect ratio treatments
available for the current input and output mode combination (for description of aspect
• The TRNR button accesses the Temporal Recursive Noise Reduction feature, cycling
through the four available settings (Off, Low, Medium, and High)
• The CNR button accesses the Codec Noise Reduction feature, cycling through the four
available settings (Off, Low, Medium, and High)
• The Film button cycles through the three available film mode treatments for active video
(Auto Film/Video mode detect, Force to Video mode, Force to Film mode)
• The Split button activates/deactivates a split-screen mode for direct comparison of the
image with and without noise reduction activated.
4.2 TheaterSync Operational Modes
TheaterSync has two operational modes, Operate and Setup. These modes are selected by a
dedicated key on the IR remote. TheaterSync also enables selection of the Operate Mode with
RS-232, USB, or Ethernet.
NEC Solutions, Inc.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
4.2.1 Operate Mode
Operate Mode is entered by toggling the Operate/Setup button on the IR remote. A brief
transition of about 3 seconds occurs when Operate Mode is entered. During this transition
period, the 24 x 2 LCD Display indicates
THEATERSYNC
Please Wait
In Operate Mode, the video output signals are activated and you may control all of TheaterSync
parameters with the remote control (except for Setup restricted parameters, as noted below).
The LCD front panel display indicates the following information in its 24 x 2 character matrix:
(Selected Input Connector) = (Input Signal Detected)
Output = (Output Resolution currently selected)
Depending on which IR remote key that you select, the operation of the OSM is slightly
different.
If you select the Menu key, the TheaterSync OSM appears on the screen. Complete details on
key once again or until 30 seconds with no IR remote activity passes.
If you select one of the dedicated HQV Feature keys, the HQV feature is immediately activated.
A brief message indicating the status of the selected HQV feature appears momentarily on the
screen (e. g. TRNR = Medium or CNR = Off).
If you select one of the Input Source keys, the selected source is chosen as the input. The
previously selected HQV Features, Aspect Ratio Treatment, Scaling and Video Parameters are
all preserved for each input; each input will appear exactly as you left it.
TheaterSync powers up in Operate mode. All operational parameters are retained from the
previous session. A Factory Reset returns all parameters to the default state (defaults are
retained as the power-up input signal.
4.2.2 Setup (Stand-by) Mode
Setup mode is entered by toggling the Operate/Setup button on the IR remote.
In Setup mode TheaterSync is in a low-power state. The output signals are de-activated (no
output will appear on your display device). Setup mode enables you to power the unit down, but
still leaves the IR receiver circuitry energized so that you can re-start the system with the IR
remote. When the unit is in Setup Mode, you can also make adjustments to certain sensitive
Page 18
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
parameters, such as Output Resolution. Visual feedback for the adjustments of Setup Mode is
seen on the 24 x 2 LCD display, rather than on OSM of the main screen. Sensitive parameters
are placed in the Setup Menu so that an inadvertent key stroke with the IR remote does not cause
Table 1: Setup Parameters
Parameter
Description1
Cycles through all of the available TheaterSync output
OUT = XXX ## Hz
Turns On (Off) the 24 x 2 LCD Display during Operate
Mode
LCD Brightness = On (Off)
These settings enables to adjust the output sync:
Free Run – Establishes a precise output timeline
Vadjust 1:1 – Forces the output timeline to be frame
locked to the input by inserting or deleting entire lines of
output video
Output Sync = Free Run (Vadjust 1:1,
Vjam)
Vjam – Maintains frame lock by truncating final line of
output frame
Lets you choose a baud rate of 1200, 9600, 19200,
57600, or 115000.
BAUD = #####
The OSM may be located pre (Input side) or post (Output
side) scaling and keystone correction
OSM Location = Input (Output)
PC Control = Active (Inactive)
DHCP = On (Off)
Turns On (Off) the computer control capability
Turns on Dynamic IP Address Selection
IP=aaa.bbb.ccc.ddd
Select IP Address (selectable only if DHCP = Off)
Select DNS Address (selectable only if DHCP = Off)
DNS=aaa.bbb.ccc.ddd
Select Alternate DNS Address
(selectable only if DHCP = Off)
2nd DNS=aaa.bbb.ccc.ddd
Gateway=aaa.bbb.ccc.ddd
SubMask=aaa.bbb.ccc.ddd
Serial No = ######
Select Gateway Address (selectable only if DHCP = Off)
Select SubNet Mask (selectable only if DHCP = Off)
Indicates the Serial # of TheaterSync unit
MAC = ## ## ## ## ## ##
Indicates the MAC Address of TheaterSync unit
1 The default parameters configurations are highlighted in bold.
NEC Solutions, Inc.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Table 2: TheaterSync Output Modes
Output Mode
Comments
VGA 60 Hz (640 x 480)
VGA 50 Hz (640 x 480)
848 x 480 60 Hz
VESA Standard
VESA Standard
/
SVGA 60 Hz (800 x 600)
SVGA 50 Hz (800 x 600)
720p 60 Hz (1280 x 720)
720p 50 Hz (1280 x 720)
XGA 72 Hz (1024 x 768)
XGA 60 Hz (1024 x 768)
XGA 50 Hz (1024 x 768)
1360 x 768 60 Hz
VESA Standard
VESA Standard
SMPTE Standard
SMPTE Standard
VESA Standard
VESA Standard
VESA Standard
/
1365 x 768 60 Hz
/
1400 x 788 60 Hz
/
SXGA 60 Hz (1280 x 1024)
SXGA 50 Hz (1280 x 1024)
SXGA+ 60 Hz (1400 x 1050)
SXGA+ 50 Hz (1400 x 1050)
1080p 60 Hz (1920 x 1080)
1080p 50 Hz (1920 x 1080)
1080p 48 Hz (1920 x 1080)
QXGA 60 Hz (2048 x 1536)
QXGA 50 Hz (2048 x 1536)
QXGA 48 Hz (2048 x 1536)
VESA Standard
VESA Standard
VESA Standard
VESA Standard
SMPTE Standard
SMPTE Standard
SMPTE Standard
/
/
/
On entry to setup mode, the 24 x 2 LCD display indicates the following:
THEATERSYNC
Setup
Select the Menu key on your IR Remote to bring up the Setup Menu on the 24 x 2 LCD display.
The LCD display will indicate the following:
“Parameter” = ???
Setup Mode
Using the Up and Down navigation keys on the remote, you can select the next parameter in a
circular list of parameters. Using the Left and Right navigation keys on the remote, you can
select the value of the parameter. In some cases, the parameter is visible in the setup menu, but
may not be altered (such as Serial Number or MAC Address).
Selection of IP addresses is slightly different. IP addresses may only be selected if the DHCP
parameter has been set to “Off”. In this case, you use the Left or Right navigation key to “enter”
the IP address. The Left key will highlight the rightmost octet; the Right key will select the
Page 20
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
leftmost octet. The Up/Down keys may then be used to increase/decrease the value of the octet.
Subsequent presses of the Left/Right key will highlight the octet immediately to the left/right.
The Up/Down keys may then be used to increase/decrease the value of the octet. When the
leftmost/rightmost octet is selected, an additional Left/Right key selection will “exit” the IP
Setup parameters.
NEC Solutions, Inc.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
5 On-Screen Menu
5.1 OSM Menu Structure
The On-Screen Menu (OSM) is the primary way of controlling and selecting functions in the
TheaterSync system. When first powered up, the TheaterSync will be in a Factory Default
configuration, with English as the OSM language, Component Video as Video Input, and
When the user selects the Factory Reset from the OSM menu, TheaterSync reloads all of these
default parameters, replacing any adjustments previously made. Certain parameters are not
affected by the Factory Reset and are left in their most recently selected position. These
the Setup Parameters are not affected by Factory Reset.
TheaterSync remembers all the signal processing parameters on a selected input basis. When the
user powers down or selects a different input, the processing parameters previously selected are
automatically re-established when returning to that input. An Input Reset sets the currently
selected input to its default parameters. (This allows the user to reset a specific input channel
without disturbing selections that affect the entire TheaterSync operation).
Table 3: OSM Main Menu Structure
Icon
Descriptio
n
Functionality
ON
OFF
Inputs
Picture
Setup
Enter this submenu to select the video or audio input.
Enter this menu to adjust the image brightness, contrast,
sharpness, gamma correction, black level, color temperature,
color, hue, tint, and aspect ratio.
Enter this submenu to review the video system, select the
background color, reset to default settings, and setup the menu
position.
Language
Info
Enter this submenu to select the language used by the OSM.
Enter this submenu to view information about the system (input
resolution, horizontal and vertical frequency, output resolution,
horizontal and vertical frequency, firmware revision, FPGA
revision, serial number, and IP address).
Page 22
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Icon
Descriptio
n
Functionality
ON
OFF
Advanced
Enter this submenu to access the advanced menu options.
Table 4: OSM Complete Menu Structure
OSM Menu Level
Comments
HDTV or SDTV
Level 1
Level 2
Level 3
Component
VGA
Level 4
Level 5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SDTV, HDTV, or Graphics
Graphics, RGB HDTV
SDTV
DVI
Video
S-Video
Composite
SDI
SDTV
SDI input selection
HDMI input selection
HDMI
Selects TosLink as audio
source
Selects S/PDIF as audio
source
TosLink
S/PDIF
-
-
-
-
Audio
Inputs
Adjusts the Audio Delay
through TheaterSync. The
Audio Delay is calibrated in
milliseconds. A delay of ‘0’
selects a delay that is
automatically adjusted to the
number of frames of delay
introduced by TheaterSync
processing. The Audio Delay
adjustment allows the user to
compensate for Audio or Video
delay that is introduced by
other system components
Audio
Delay
-100 - +100,
0 (default)
-
-
The higher the setting, the
greater the brightness.
The lower the setting, the lower
the brightness.
0 - 100,
50 (default)
Brightness
Contrast
-
-
Picture
Settings
Picture
The higher the setting, the
greater the contrast.
The lower the setting, the lower
the contrast.
0 - 100,
50 (default)
NEC Solutions, Inc.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
OSM Menu Level
Level 3
Comments
Level 1
Level 2
Level 4
Level 5
The higher the setting, the
sharper the image (edge
enhancement).
The lower the setting, the lower
the sharpness.
The higher the setting, the
better the image (detail
enhancement).
0 - 100,
50 (default)
Sharpness
-
-
Detail
0 - 100,
Enhancement 50 (default)
The lower the setting, the lower
the detail enhancement.
Gamma 1.0 Gamma LUT for linear
(default)
response (1.0).
Gamma LUT for non-linear
response (1.5).
Gamma 1.5
Gamma LUT for non-linear
response (2.2).
Gamma 2.2
Gamma 2.4
Gamma 2.5
Gamma 2.8
Input
Gamma
Gamma LUT for non-linear
response (2.4).
Gamma LUT for non-linear
response (2.5).
Gamma LUT for non-linear
response (2.8).
Gamma
Mode
Picture
Settings
Picture
Gamma 1.0 Gamma LUT for linear
(default)
response (1.0).
Gamma LUT for non-linear
response (2.2).
Gamma 2.2
Gamma LUT for non-linear
response (2.4).
Output
Gamma
Gamma 2.4
Gamma 2.5
Gamma LUT for non-linear
response (2.5).
Gamma LUT for non-linear
Gamma 2.8 response (2.8).
Gives a blue tint to the white
colors.
9300K
-
-
-
6500K
Color Temp
Gives a neutral tint to the white
colors.
(default)
Gives a red tint to the white
colors.
5500K
The higher the setting, the
greater the intensity. The lower
the setting, the lower the
intensity.
0 - 100,
Color
-
50 (default)
Page 24
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
OSM Menu Level
Comments
Level 1
Level 2
Level 3
Level 4
Level 5
The higher the setting, the
more greenish the picture. The
lower the setting, the more
purplish the picture.
0 - 360,
180
(default)
Hue
-
Returns all of the adjustments
for a single input to the Factory
Default state. All the other
inputs and selections that affect
the TheaterSync operation
(such as Keystone Correction)
are unaffected
Picture
Settings
Confirm
YES/NO
Input Reset
-
Maintains the aspect ratio:
•
4:3 input and 16:9 output -
Output image would be
displayed with black pillar
bars (maintains input
aspect ratio)
•
•
4:3 input and 4:3 output -
No change
16:9 input and 16:9 output -
No change
Standard
(default)
-
-
•
16:9 input and 4:3 output -
Output image would be
displayed with black letter
box bars (maintains input
aspect ratio)
Picture
Fills the Output Screen by
stretching the image (distorting
the aspect ratio):
•
4:3 input and 4:3 output –
Grayed out, no action
4:3 input and 16:9 output –
Image is linearly stretched
horizontally to fill the output
screen
Aspect
Ratio
•
Full Screen
-
-
•
•
16:9 input and 4:3 output -
Image is linearly stretched
vertically to fill the output
screen
16:9 input and 16:9 output
– Grayed out, no action
information.
Fills the Output Screen by
cropping the image
(maintaining aspect ratio).
•
4:3 input and 4:3 output –
Grayed out, no action
Zoom
-
-
•
4:3 input and 16:9 output –
Top and bottom portions of
the image are cropped
NEC Solutions, Inc.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
OSM Menu Level
Level 3
Comments
Level 5
Level 1
Level 2
Level 4
•
16:9 input and 4:3 output –
Left and right portions of
the image are cropped
16:9 input and 16:9 output
– Grayed out, no action
•
information.
This mode is used with DVDs
(Standard Definition) that are in
Widescreen [16:9] format:
•
4:3 input and 4:3 output –
The image is letter boxed
4:3 input and 16:9 output –
The image appears full
screen
•
Picture
Anamorphic
-
-
•
•
16:9 input and 4:3 output –
Grayed out, no action
16:9 input and 16:9 output
– Grayed out, no action
information.
Fills the Output Screen by
stretching the image (distorting
the aspect ratio):
Aspect
Ratio
•
4:3 input and 4:3 output –
Grayed out, no action
4:3 input and 16:9 output –
Image is non-linearly
•
Stadium
-
-
stretched horizontally to fill
the output screen
•
•
16:9 input and 4:3 output –
Grayed out, no action
16:9 input and 16:9 output
– Grayed out, no action
information.
Adjusts the vertical position of
image (default setting depends
on the input video/graphics
source)
Adjusts the horizontal position
of image (default setting
depends on the input
video/graphics source)
Vertical
0 - 100
-
-
Picture
Position
Horizontal
0 - 400
-
Automatically centers the
image for graphic inputs
Autosync
Sync
-
-
-
0 - 200,
100
(default)
Clock
Adjusts clock sync
NEC Solutions, Inc.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
OSM Menu Level
Comments
Level 1
Level 2
Level 3
Level 4
Level 5
0 - 100,
50 (default)
Phase
-
Adjusts clock phase
Off
On
-
-
-
-
Status
Left
0.0 – 10.0
0.0 (default)
Sets the percentage of
Overscan on the left edge
-
0.0 – 10.0
0.0 (default)
0.0 – 10.0
0.0 (default)
0.0 – 10.0
0.0 (default)
Sets the percentage of
Overscan on the right edge
Sets the percentage of
Overscan on the top edge
Sets the percentage of
Overscan on the bottom edge
Picture
Overscan
Right
Top
-
-
-
Bottom
Sets the OSM menu position in
the center of the display
Center
-
-
-
-
Sets the OSM menu position in
the top left corner of the display
Top Left
Sets the OSM menu position in
the top right corner of the
display
Sets the OSM menu position in
the bottom left corner of the
display
Sets the OSM menu position in
the bottom right corner of the
display
Menu
Position
Top Right
Bottom Left
Bottom Right
-
-
-
-
-
-
Setup
Displays test pattern images on
screen, with OSM off. Up- and
down-arrows navigate user
through all 10 available test
patterns. Left-arrow key
returns user to Test Pattern
menu.
Test
Patterns
-
-
-
Off (default)
On
-
-
-
-
-
Trigger A
Trigger B
-
-
-
12 V
Triggers
Off (default)
On
Factory
Reset
Confirm
YES/NO
-
-
-
-
Resets to default settings
Selects the language for the
OSM menus
Language
English
-
French
-
-
-
-
-
-
German
Italian
-
-
-
-
-
-
Spanish
NEC Solutions, Inc.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
OSM Menu Level
Comments
Level 5
Level 1
Level 2
Level 3
Level 4
Portuguese
-
-
-
-
-
Swedish
Russian
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Japanese
-
Selects the language for the
OSM menus
Language
Chinese
Simplified
Chinese
-
-
-
Traditional
Korean
Input
Resolution
Input H
Frequency
Input V
Frequency
Output
Mode
Output
Resolution
Output H
Frequency
Output V
Frequency
-
-
-
-
-
-
-
-
-
-
Shows the source resolution
Shows the source H frequency
Shows the source V frequency
Shows the display mode
Shows the display resolution
Shows the display H frequency
Shows the display V frequency
Shows the synchronization type
Sync
Info
Firmware
Revision
Serial
Shows the firmware revision
number
Shows the board serial
number.
Number
Shows the IP address only if
the Ethernet cable is connected
to the board and the IP address
has been assigned by DHCP
IP Address
-
-
-
FPGA
Revision
Shows the current revision
number for the FPGA code
-
-
-
-
-
-
Standby
Micro
Rev. #
Shows the firmware revision
number for the standby-mode
microcontroller
Horizontal
and Vertical
Keystone
Controls the horizontal position
of the display top left corner
Advanced Projection
Top Left H
Top Left V
-
-
Controls the vertical position of
the video display top left corner
Page 28
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
OSM Menu Level
Comments
Level 1
Level 2
Level 3
Level 4
Level 5
Controls the horizontal position
of the video display bottom left
corner
Bottom Left
H
-
Controls the vertical position of
the video display bottom left
corner
Bottom Left
V
Advanced
-
Controls the horizontal position
of the display top right corner
Top Right H
Top Right V
-
-
Horizontal
and Vertical
Keystone
Controls the vertical position of
the display top right corner
Controls the horizontal position
of the video display bottom
right corner
Controls the vertical position of
the video display bottom right
corner
Bottom
Right H
-
-
Bottom
Right V
Projection
Front
Tabletop
(default)
-
-
-
Normal projection mode
Front
Ceiling
Compensate the image for
ceiling-mounting scenario
Projection
Mounting
Compensate the image for
projection from behind the
screen
Rear
Tabletop
Compensate the image for
ceiling-mounted rear-projection
scenario
Rear Ceiling
-
-
-
HQV On
-
-
Process main image in the TVP
(default)
Video
Processing
Mode
Process main image in Overlay
Scaler (bypass the TVP
processor)
HQV Off
(Bypass)
The system automatically
selects the best mode for de-
interlacing (film or video)
Auto
(default)
-
-
HQV Film
Mode
Forces to video mode for de-
interlacing
Video
Film
-
-
-
-
Forces to film mode for de-
interlacing
Expands video range signals
(16-235) linearly to full range
output
Provides Luma processing
optimized for movies; expands
video range signals.
Video 2
Cinema
-
-
-
-
BCE
2 Default for HDMI, Component, Composite, S-Video, and SDI inputs.
NEC Solutions, Inc.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
OSM Menu Level
Level 3
Comments
Level 5
Level 1
Level 2
Level 4
Enhances color, expands video
range signals.
Vivid
-
-
Enhances detail in dark
Dark Scene
Bright Scene
Graphics3
-
-
-
-
-
scenes, expands video range
signals.
Enhances detail in bright
scenes, expands video range
signals.
Transfers full range input
signals (0-255) to full range
output
BCE
-
Turns off Temporal Recursive
Noise Reduction (TRNR)
Off
-
-
Low
(default)
Select TRNR -- low bias setting
TRNR
Select TRNR -- medium bias
setting
Select TRNR -- high bias
setting
Turns off the Codec Noise
Reduction
Med
High
-
-
-
Advanced
HQV Noise
Reduction
Off (default)
Select Codec Noise Reduction,
low level
Low
-
-
-
CNR
Select Codec Noise Reduction,
medium level
Medium
High
Select Codec Noise Reduction,
high level
Off (default)
-
-
-
-
Toggles the split screen mode
Toggles the split screen mode
Split
On
5.2 Aspect Ratio
TheaterSync provides five different aspect ratio treatments. The operation mode of these
treatments depends on the aspect ratio of the input channel and the output display.
The TheaterSync assumes that the aspect ratio of input and output is consistent with the industry
standard definition of the aspect ratio of the particular input signal and video mode. Output
aspect ratio is thus determined by the resolution selected by the user in Setup Mode. Input aspect
ratio is determined by the TheaterSync video mode recognition circuitry. Only two output aspect
3 Default for DVI and Analog RGB inputs.
4 The special case of 1280 x 1024 SXGA (an aspect ratio of 5:4) on output is treated as if it were 4:3. The output of
a 1280 x 1024 display will be slightly distorted; circles will appear to be vertically oriented ovals. Since the
Page 30
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Inputs considered to have 4:3 aspect ratio are:
• Computer Graphics signals with a 4:3 aspect ratio appearing on the DVI and Analog
RGB inputs
• SDTV signals (NTSC and PAL derived) appearing on the Composite, S-Video, and
Component inputs
• SDTV signals (NTSC and PAL derived) appearing on the SDI input
• SDTV signals (NTSC and PAL derived) appearing on the HDMI input
Inputs considered to have 16:9 aspect ratio are:
• Computer Graphics signals with a 16:9 aspect ratio appearing on the DVI and Analog
RGB inputs
• HDTV signals (480p, 720p, 1080i, 1080p) appearing on the Component input
• HDTV signals (480p, 720p, 1080i, 1080p) appearing on the SDI input
• HDTV signals (480p, 720p, 1080i, 1080p) appearing on the HDMI input
The five aspect ratio treatments, Standard, Full Screen, Zoom, Anamorphic, and Stadium are
intended to achieve different aspect ratio objectives, and therefore behave differently depending
on which input and output aspect ratios are currently selected. The Aspect Ratio objectives are
the following:
• Standard: always displays the correct aspect ratio of the input picture; adds black bars at
the top and bottom or sides of the picture to achieve this objective
• Full Screen: always fills the screen with the complete picture; linearly distorts the picture
to achieve this objective
• Zoom: always fills the screen with the correct aspect ratio of the input picture; crops the
picture’s top and bottom or sides to achieve this objective
• Anamorphic: intended to handle the specific case of 16:9 aspect ratio anamorphically
encoded into a 4:3 aspect ratio signal (e. g. an NTSC DVD encoded with a 16:9 picture
• Stadium: intended to handle the specific case of a 4:3 input aspect ratio and 16:9 output
aspect ratio
of Input Aspect Ratio and Output Aspect Ratio.
TheaterSync is intended for Widescreen processing, the 1280 x 1024 SXGA is not a frequently encountered case.
Input of 1280 x 1024 will be treated as a pillar boxed 4:3 signal (i.e. it will have narrow black bars on the Right and
Left); aspect ratio of the picture content will be undistorted.
NEC Solutions, Inc.
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Table 5: Aspect Ratio Treatments for 4:3 Input with 4:3 Output
OSM Menu Name
Description
4:3 input signals shown full screen on 4:3 output display
Standard
Full Screen
Zoom
Grayed out. No action.
Same as “Standard” mode above.
Anamorphic or widescreen encoded DVDs shown letterbox on
4:3 output display. These DVDs have 16:9 content that has
been compressed and expanded vertically to fit the NTSC or
PAL signal.
Anamorphic
Stadium
Grayed out. No action.
Table 6: Aspect Ratio Treatments for 4:3 Input with 16:9 Output
OSM Menu Name
Description
4:3 input signals are shown in a pillar box on the 16:9 output
display
Standard
4:3 input is linearly stretched horizontally to fill the 16:9 screen
Full Screen
Page 32
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
OSM Menu Name
MKT-0026-UMN-1.002F
Description
Zoom
Grayed out. No action.
SDTV input is displayed on a full screen 16:9 output display
Anamorphic
4:3 input signals are non-linearly stretched in the horizontal
direction to fill 16:9 output displays. Horizontal and vertical
scaling is equal in the middle, more horizontal stretching
towards left and right sides to fill 16:9 outputs
Stadium
NEC Solutions, Inc.
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Table 7: Aspect Ratio Treatments for 16:9 Input with 4:3 Output
OSM Menu Name
Description
All HDTV inputs are assumed to be 16:9. HDTV input signals
(1080i and 720p) are shown in a letterbox on the 4:3 output
display
Standard
Image stretched vertically to fill full screen.
Full Screen
16:9 HDTV input signals shown in 4:3 output display, cropped
on left and right sides
Zoom
Anamorphic
Stadium
Grayed out. No action.
Grayed out. No action.
Page 34
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Table 8: Aspect Ratio Treatments for 16:9 Input with 16:9 Output
OSM Menu Name
Description
16:9 input signals shown full screen on 16:9 output display
Standard
Full Screen
Zoom
Grayed out. No action.
Grayed out. No action.
Grayed out. No action.
Grayed out. No action.
Anamorphic
Stadium
NEC Solutions, Inc.
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
6 Appendix A
Table 9: Input Modes Supported
Input Timing Format
Input Video Source
Item
No.
Mode
Description
Resolution
Frequency
RGB
DVI
HDMI
Composite
S-video
Component
SDI
1
2
480i (NTSC) 720 x 485
60 Hz
50 HZ
-
-
-
YES
YES
YES
YES
YES
YES
YES
YES
576i (PAL)
720 x 576
720 x 576
-
-
YES
576i
(SECAM)
3
50 Hz
60 Hz
50 Hz
-
-
-
-
-
YES
YES
-
-
-
-
4
5
480p
576p
720 x 483
720 x 576
YES
YES
YES
YES
-
-
-
-
YES
YES
HDTV 720
Progressive
6
7
1280 x 720
1280 x 720
60 Hz
50 Hz
-
-
-
YES
YES
YES
YES
YES
YES
-
-
-
-
-
-
YES
YES
YES
YES
-
HDTV 720
50 Hz
Progressive
HDTV 1080
Interlaced at
60 Hz
8
9
1920 x 1080 60 Hz
YES
HDTV 1080
Interlaced at
50 Hz
1920 x 1080 50 Hz
1920 x 1080 24 Hz
1920 x 1080 25 Hz
1920 x 1080 30 Hz
1920 x 1080 48 Hz
1920 x 1080 50 Hz
1920 x 1080 60 Hz
-
-
-
-
-
-
-
YES
YES
-
-
-
-
-
-
-
-
-
-
-
-
YES
YES
YES
YES
YES
YES
YES
1080p at
24 Hz
10
11
12
13
14
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1080p at
25 Hz
1080p at
30 Hz
1080p at
24sF
1080p at
25sF
1080p at
30sF
15
16
-
-
-
-
-
-
-
-
YES
-
DOS TEXT
640 x 400
70 Hz
YES
YES
YES
Page 36
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterSync Video Processor User Manual
MKT-0026-UMN-1.002F
Input Timing Format
Input Video Source
Composite S-video
Item
No.
Mode
Resolution
Frequency
RGB
DVI
HDMI
Component
SDI
Description
VGA at
60 Hz
17
18
640 x 480
60 Hz
YES
YES
YES
-
-
-
-
SVGA at
75 Hz
800 x 600
848 x 840
1024 x 576
75 Hz
60 Hz
60 Hz
YES
YES
YES
YES
YES
YES
YES
-
-
-
-
-
-
-
-
-
-
-
-
19
20
848 x 480
-
-
1024 x 576
XGA at
75 Hz
21
22
1024 x 768
75 Hz
YES
YES
YES
-
-
-
-
SXGA at
75 Hz
1280 x 1024 76 Hz
YES
YES
YES
YES
-
YES
YES
YES
YES
YES
YES
YES
YES
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
23
24
25
26
27
28
1360 x 768
1365 x 768
SXGA+
1360 x 768
1365 x 768
60 Hz
60 Hz
-
-
1400 x 1050 60 Hz
1600 x 1200 60 Hz
1920 x 1200 60 Hz
2048 x 1536 60 Hz
-
UXGA
YES
WUXGA
QXGA
-
-
-
-
MAC II
Normal 13in
29
30
31
32
640 x 480
832 x 624
1024 x 768
67 Hz
75 Hz
75 Hz
YES
YES
YES
YES
YES
YES
YES
-
-
-
-
-
-
-
-
-
-
-
-
MAC II
Normal 16in
-
-
MAC II
Normal 19in
MAC II
Normal 21in
1152 x 870
1440 x 960
75 Hz
96 Hz
YES
YES
YES
YES
YES
YES
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
33
34
35
MAC
-
-
-
-
-
-
MAC 20
MAC 23
1680 x 1050 88 Hz
1920 x 1200 76 Hz
NEC Solutions, Inc.
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MKT-0026-UMN-1.002F
TheaterSync Video Processor User Manual
Page 38
NEC Solutions, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|