MultiSync E231W
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
European
Continental
Plug Type
North America
U.K.
Chinese
Japanese
Plug Shape
Country
Voltage
U.S.A./Canada
120*
EU (except U.K.)
230
U.K.
230
China
220
Japan
100
*When operating the MultiSync E231W monitor with its AC 125-240V power supply, use a power supply cord that matches the
power supply voltage of the AC power outlet being used.
NOTE:
This product can only be serviced in the country where it was purchased.
Registration Information
Declaration
Declaration of the Manufacturer
We hereby certify that the colour monitor MultiSync
E231W (L239NP) is in compliance with
and marked with
Council Directive 2006/95/EC:
– EN 60950-1
Council Directive 2004/108/EC:
– EN 55022
NEC Display Solutions, Ltd.
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
Council Directive 2009/125/EC:
EC No.1275/2008
– EN 62301:2005
English-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1.
Use the attached specified cables with the MultiSync E231W (L239NP) color monitor so as not to interfere with radio
and television reception.
(1)
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,
and meet the following condition.
Power supply cord
Plug shape
Non shield type, 3-conductor
U.S.A
(2)
Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable.
Use of other cables and adapters may cause interference with radio and television reception.
2.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington, D.C., 20402, Stock No. 004-000-00345-4.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address:
500 Park Blvd, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Tel. No.:
Type of Product:
Display Monitor
Equipment Classification: Class B Peripheral
Models: MultiSync E231W (L239NP)
We hereby declare that the equipment specified above conforms
to the technical standards as specified in the FCC Rules.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.
ENERGY STAR is a U.S. registered trademark.
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,
Norway, Spain, Sweden, U.K.
NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.
MultiSync is a registered trademark of NEC Display Solutions, Ltd. in the countries of U.K., Italy, Austria, Netherlands,
Switzerland, Sweden, Spain, Denmark, Germany, Norway and Finland.
All other brands and product names are trademarks or registered trademarks of their respective owners.
®
As an ENERGY STAR Partner, NEC Display Solutions of America, Inc. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency. The ENERGY STAR emblem does not represent EPA
endorsement of any product or service.
DisplayPort is trademarks of Video Electronics Standards Association.
English-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC LCD COLOUR MONITOR:
•
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.
•
•
Do not spill any liquids into the cabinet or use your monitor near water.
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful
or fatal or may cause electric shock, fire or equipment failure.
•
•
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to
the monitor.
•
The power supply cord you use must have been approved by and comply with the safety standards of your country.
(Type H05VV-F 3G 0.75mm2 should be used in Europe).
•
•
•
•
•
•
In U.K, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.
Do not place any objects onto the monitor and do not use the monitor outdoors.
Do not bend, crimp or otherwise damage the power cord.
Do not use monitor in high temperatured, humid, dusty, or oily areas.
Do not cover vent on monitor.
Do not touch LCD panel surface while transporting, mounting and setting. Applying pressure on the LCD panel can cause
serious damage.
•
To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install
the monitor in a stable location and take measures to prevent falling.
Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
•
•
•
•
•
•
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
If the monitor does not operate normally by following operating instructions.
If you notice any structural damage such as cracks or unnatural wobbling.
If glass is broken, handle with care.
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
•
Allow adequate ventilation around the monitor so that heat can properly dissipate.
Do not block ventilated openings or place the monitor near a radiator or other heat
sources. Do not put anything on top of monitor.
CAUTION
•
The power cable connector is the primary means of detaching the system from the
power supply. The monitor should be installed close to a power outlet which is easily
accessible.
•
•
•
Handle with care when transporting. Save packaging for transporting.
Carry the monitor holding the built-in handle and bottom frames of the monitor.
Do not carry holding only the stand.
•
Image Persistence: Please be aware that LCD Technology may experience a phenomenon known as Image Persistence.
Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike
CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be
turned off for one hour to erase the image.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and
using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
English-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:
•
•
For optimum performance, allow 20 minutes for warm-up.
Adjust the monitor height so that the top of the screen is at or slightly below eye level.
Your eyes should look slightly downward when viewing the middle of the screen.
•
Position your monitor no closer than 40 cm and no further away than 70 cm from your
eyes. The optimal distance is 50 cm.
•
•
Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.
Position the monitor at a 90° angle to windows and other light sources to minimize
glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your
screen.
•
•
•
•
If reflected light makes it hard for you to see your screen, use an anti-glare filter.
Adjust the monitor’s brightness and contrast controls to enhance readability.
Use a document holder placed close to the screen.
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize
turning your head while you are typing.
•
•
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).
Get regular eye checkups.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the following:
•
•
•
•
•
•
Adjust the Brightness until the background raster disappears.
Do not position the Contrast control to its maximum setting.
Use the preset Size and Position controls with standard signals.
Use the preset Colour Setting.
Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.
Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue to insufficient
contrast.
Cleaning the LCD Panel
•
•
•
•
When the liquid crystal panel is stained with dust or dirt, please wipe with soft cloth gently.
Please do not rub the LCD panel with hard material.
Please do not apply pressure to the LCD surface.
Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface.
Cleaning the Cabinet
•
•
•
Unplug the power supply
Gently wipe the cabinet with a soft cloth
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.
NOTE:
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or
peel.
English-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•
•
•
•
•
•
MultiSync LCD monitor with tilt/swivel/pivot/height adjust base
Power Cord
Base stand
Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
Video Signal Cable (DVI-D to DVI-D)
Setup Manual
Power Cord
(Type of power cord included
will depend on the where the
LCD monitor is to be shipped)
Base stand
Setup Manual
Setup Manual
15-pin mini D-SUB male to
15-pin mini D-SUB male
DVI-D to DVI-D
*
Remember to save your original box and packing material to transport or ship the monitor.
English-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
To attach the Base to the LCD stand:
1. Place monitor face down on a non-abrasive surface (Figure 1).
NOTE:
Handle with care when monitor facing down, for avoiding damage to the front
control buttons.
2. Please pivot base 90 degrees as shown in Figure 1.
NOTE: Handle with care when pulling the stand.
3. Attach the base stand to LCD monitor and lock screws of base stand bottom (Figure 2).
NOTE: Reverse this procedure if you need to re-pack the monitor.
Control
buttons
Figure 1
Screws
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the
connector of the display card in your system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the
connector of the display card in your system (Figure A.2). Tighten all screws.
For the MAC: Connect the Macintosh cable adapter to the computer, then attach the
15-pin mini D-SUB signal cable to the Macintosh cable adapter (Figure A.3).
Tighten all screws.
Figure 2
For the PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system
(Figure A.4).
DVI signal cable
Macintosh
Cable Adapter
(not included)
DisplayPort cable
(not included)
Figure A.1
Figure A.2
Figure A.3
Figure A.4
NOTE:
Some Macintosh systems do not require a Macintosh cable adapter.
3. Place hands on each side of the monitor to tilt the LCD panel 20-degree angle and lift up to the highest position
(FigureB.1).
4. Connect all cables to the appropriate connector on the back of the monitor (Figure B.1).
5. Position the Video Signal Cable and power cord between the holes on the Stand, as indicated in Figure B.2/Figure B.3.
20˚ Tilt
Highest stand position
DisplayPort
DVI
Power Cord
D-SUB
Figure B.1
Figure B.2
Figure B.3
NOTE:
1. Please use a DisplayPort cable with a DisplayPort logo.
2. The DisplayPort connector does not supply power to the connected component.
3. When removing the DisplayPort cable, hold down the top button to release the lock.
English-6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Connect the power cord to the power outlet (Figure C.1).
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.
7. Turn on the monitor with the front power button and the computer (Figure C.1).
8. No-Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.
For further adjustments, use the following OSD controls:
• Auto Adjust Contrast (Analog input only)
• Auto Adjust (Analog input only)
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.
NOTE:
If you have any problems, please refer to the Troubleshooting section of this User’s Manual.
Power Button
Figure C.1
Raise and Lower Monitor Screen
The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lift or lower to
the desired height (Figure RL.1).
NOTE:
Handle with care when raising or lowering the monitor screen.
Do not grasp the rear handle when raising or lowering the monitor. It may cause pitching your finger between the
stand and the monitor.
Figure RL.1
Tilt and Swivel
Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).
NOTE:
Handle with care when tilting the monitor screen.
Figure TS.1
English-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Rotation
Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching with your
fingers.
To raise the screen, with one hand, grip the top of the display by the handle using the other hand to grip the bottom. Lift up to
the highest position (Figure RL.1).
To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter-
clockwise from Portrait to Landscape (Figure R.1).
Figure R.1
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Disconnect all cables.
2. Place monitor face down on a non-abrasive surface (Figure S.1).
NOTE:
Handle with care when monitor facing down, for avoiding damage to the front control buttons.
3. Remove the 4 screws connecting the stand to the monitor (Figure S.1).
NOTE:
In order to avoid stand drop, when removing screws, please support stand with your hand.
Control buttons
Figure S.1
4. Remove the stand (Figure S.2).
5. The monitor is now ready for mounting in an alternate manner.
6. Connect the cables to the back of the monitor.
Figure S.2
English-8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Reverse this process to re-attach stand.
NOTE:
Use only VESA-compatible alternative mounting method.
Handle with care when removing stand.
NOTE:
Match “TOP SIDE” mark on stand to top side of the monitor head when
re-attaching stand.
“TOP SIDE” mark
Please match top side
of the monitor
Hole of “ ” mark
Please assemble
then together
Flexible Arm Installation
This LCD monitor is designed for use with a flexible arm. To mount the monitor to a flexible arm:
1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.
2. Using the 4 screws from the stand removal, attach the arm to the monitor (Figure F.1).
NOTE:
1. When mounting, use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the
monitor or stand.
2. The LCD monitor should only be used with an approved arm (e.g. GS mark). To meet the safety requirements,
the monitor must be mounted to an arm, which guaranties the necessary stability under consideration of the
weight of the monitor.
3. The mounting stand must be able to sustain at least 18.4 kg and be UL certified.
Thickness of Bracket (Arm)
2.0~3.2 mm
4 Screws (M4)
Additional 4 VESA
(Max Depth: 9.5 mm)
100 mm
100 mm
Weight of LCD assembly: 4.5 kg MAX
Figure F.1
An additional 4 VESA holes are provided for those users needing a lower monitor head position, than that available from the
monitor stand in shipping configuration.
The monitor stand can be re-attached using the 4 screws to the lower position VESA holes.
NOTE:
1. The monitor head tilt function may have impaired operation when attached to the lower position VESA holes.
2. The monitor head pivot function should not be used when attached to the lower position VESA holes.
English-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
OSD (On-Screen Display) control buttons on the front of the monitor function
as follows:
To access OSD menu, press any of the control buttons (MENU, Left, Right, Down, Up).
To change signal input, press the SELECT button.
To change ECO MODE, press the RESET/ECO MODE button.
NOTE:
OSD must be closed in order to change signal input.
Button
Menu
1 Ambibright Sensor
Detects the level of ambient lighting allowing the monitor to make adjustments to various settings
resulting in a more comfortable viewing experience. Do not cover this sensor.
2 MENU
Open OSD main menu.
Exits the OSD controls.
Exits to the OSD main menu.
3 4-Direction-Key
Left/Right
Down/Up
Moves the highlighted area left/right to select control menus.
Moves the bar left/right to increase or decrease the adjustment.
Direct adjust of BRIGHTNESS if HOT KEY is set to ON.
Enters the OSD menu if HOT KEY is set to OFF.
Up
Left
Right
Moves the highlighted area down/up to select one of the controls.
Direct adjust of CONTRAST if HOT KEY is set to ON.
Enters the OSD menu if HOT KEY is set to OFF.
Down
4 SELECT
Enter the OSD sub menu. Active the selected function.
Change the Input source (No OSD condition).
5 RESET/ECO MODE
6 Power
Resets the highlighted control menu to the factory setting. Switches the ECO MODE.
Activates Auto Adjust function if pushed for 3 seconds (No OSD condition and Analog input only).
Turns the monitor on and off.
NOTE:
When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the
RESET function by pressing the MENU button.
Brightness/Contrast Controls
BRIGHTNESS
Adjusts the overall image and background screen brightness.
If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear.
CONTRAST
Adjusts the image brightness in relation to the background.
AUTO CONTRAST (Analog input only)
Adjusts the image displayed to optimal settings.
ECO MODE
Decreases the power consumption by reducing the brightness level.
OFF: Sets brightness variable from 0% to 100%.
(ECO MODE) 1: Sets brightness variable range from 0% to 80%.
This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement
conditions.
(ECO MODE) 2: Sets brightness variable range from 0% to 40%.
This setting can adjust brightness to a range in which power is reduced by 40% compared to the maximum
brightness setting.
When this function is set to ON, a CARBON FOOTPRINT bar will appear alongside the brightness adjustment bar.
NOTE:
This function is disabled when DV mode is set for Dynamic.
English-10
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO BRIGHTNESS
OFF: No function.
(AUTO BRIGHTNESS) 1: Automatically adjusts the brightness to the optimal setting by detecting the brightness
level of the environment*1.
(AUTO BRIGHTNESS) 2: Automatically adjusts the brightness to the optimal brightness setting based on the white
display area.
The environmental brightness sensor (Ambibright sensor) has no function.
(AUTO BRIGHTNESS) 3: Automatically adjusts the brightness to the optimal setting based on the white display area
and by using the AmbiBright sensor to detect the brightness level of the environment.
*1: Please refer to Page 17 for full “Auto Brightness” information.
NOTE:
This function is disabled when DV mode is set for Dynamic.
DV MODE
Dynamic Visual Mode allows you to select setting for Movie, Photo, Dynamic and etc.
STANDARD: Standard setting.
TEXT: Setting that makes letters and lines crisp, best suited for regular word processing and spread sheet.
MOVIE: Setting that boosts dark tones, best suited for movies.
GAMING: Setting that boosts whole tones, best suited for games that provide images with more power.
PHOTO: Setting that gives contrast, best suited for natural images and still images.
DYNAMIC: Setting that makes brightness dark by detecting black area. It gives high contrast.
Auto Adjust (Analog input only)
Automatically adjusts the Image Position, Horizontal Size and Fine settings.
Image Controls (Analog input only)
LEFT / RIGHT
Controls Horizontal Image Position within the display area of the LCD.
DOWN / UP
Controls Vertical Image Position within the display area of the LCD.
H.SIZE
Adjusts the horizontal size by increasing or decreasing this setting.
FINE
Improves focus, clarity and image stability by increasing or decreasing this setting.
INPUT RESOLUTION (Analog Input Only)
Selects resolution’s priority of input signal to one of the following pair: 1360 x 768 or 1280 x 768 or 1024 x 768
(vertical resolution 768), 1680 x 1050 or 1400 x 1050 (vertical resolution 1050).
Colour Control System
Colour Control System: Six colour presets select the desired colour setting (sRGB and NATIVE colour presets are
standard and cannot be changed).
1, 2, 3, 5: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in
colour will appear on screen and the direction (increase or decrease) will be shown by the bars.
NATIVE: Original colour presented by the LCD panel that is unadjustable.
sRGB: sRGB mode dramatically improves the colour fidelity in the desktop environment by a single standard RGB
colour space. With this colour supported environment, the operator could easily and confidently communicate colour
without further colour management overhead in the most common situations.
NOTE: When MOVIE, GAMING, or PHOTO is selected as the DV MODE, NATIVE is selected automatically as the
six colour preset and cannot be changed.
English-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
VIDEO DETECT: Selects the method of video detection when more than one computer is connected.
FIRST: The video input has to be switched to “FIRST” mode. When current video input signal is not present,
then the monitor searches for a video signal from the other video input port. If the video signal is present in the
other port, then the monitor switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
NONE: The Monitor will not search the other video input port unless the monitor is turned on.
EXPANSION MODE: Selects the zoom mode.
FULL: The image is expanded to 1920 x 1080, regardless of the resolution.
ASPECT: The image is expanded without changing the aspect ratio.
OFF TIMER: Monitor will automatically power-down when you have selected a predetermined amount of time.
Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes.
Press any OSD button to delay the turn off time.
LED BRIGHTNESS: You can adjust the Blue LED brightness.
DDC/CI: This function allows the DDC/CI function ON or OFF.
FACTORY PRESET: Selecting Factory Preset allows you to reset all OSD control settings back to the factory
settings. Individual settings can be reset by pressing the RESET/ECO MODE button.
Menu Tools
LANGUAGE: OSD control menus are available in eight languages.
OSD LEFT/RIGHT: You can choose where you would like the OSD control image to appear horizontally on your
screen.
OSD DOWN/UP: You can choose where you would like the OSD control image to appear vertically on your screen.
OSD TURN OFF: The OSD control menu will stay on as long as it is in use. In the OSD Turn Off submenu, you can
select how long the monitor waits after the last touch of a button to shut off the OSD control menu.
OSD LOCK OUT: This control completely locks out access to all OSD control functions without Brightness and
Contrast. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the
OSD controls are locked out. To activate the OSD Lock Out function, press SELECT, then right control button and
hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then left control button and hold down
simultaneously while in the OSD menu.
HOT KEY: You can adjust the brightness and contrast directly. When this function is set to ON, you can adjust the
brightness with left or right control and contrast with up or down control while the OSD menu is off.
SIGNAL INFORMATION: If you select “ON”, monitor displays “VIDEO INPUT MENU” after change Input-Port.
If you select “OFF”, monitor doesn’t display “VIDEO INPUT MENU” after change Input-Port.
IPM SETTING: The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of
inactivity. The IPM has two settings:
STANDARD: Monitor enters power save mode automatically when the input signal is lost.
SENSOR: Monitor enters power save mode automatically when the amount of surrounding light goes below the
level determined by you. The level can be adjusted in IPM sensor setting.
When in power save mode, the LED on the front of the monitor becomes dark blue. When in power save mode,
push any of the front buttons, except for POWER and SELECT, to return to normal.
When the amount of surrounding light returns to normal levels, the monitor will automatically return to normal mode.
IPM SENSOR SETTING: Adjusts threshold level of sensor for detected dark condition and shows current sensor
measurement result below.
English-12
Download from Www.Somanuals.com. All Manuals Search And Download.
ECO Information
CARBON SAVINGS: Displays the estimated carbon savings information in kg.
COST: Displays the electricity cost savings in balance.
CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial
setting is based on the OECD (2008 Edition).
CURRENCY SETTING: Displays electricity pricing (available in 6 currency units).
CURRENCY CONVERT SETTING: Allows for localization of the electricity costs for accurate information in the
electrical rate savings.
NOTE: This model’s initial setting is Currency = US$ and its Currency Convert setting = $0.11.
This setting can be changed by using the ECO information menu.
If you want to use the French setting, please refer to steps below:
1. Open menu by pressing the Menu button and select the ECO information menu using the left or right key.
2. Select Currency setting item pressing the Up or Down key.
3. The French currency unit is Euro ( ). You can adjust currency setting to Euro icon ( ) from US dollar
icon ($) using the Left or Right key in Current setting item.
4. Select Currency Convert Setting item using the Up or Down key*.
5. Adjust Currency Convert Setting item using the Right or Left key.
* This initial Euro ( ) setting is Germany of OECD (2007 Edition).
Please check receipt of French’s electricity prices or OECD data for French.
French of OECD (2007 Edition) was 0.12.
Information
The Information menu indicates the current input, display resolution, horizontal and vertical frequency, and polarity
settings of the monitor. The model and serial numbers of your monitor are also indicated.
OSD Warning
OSD Warning menus disappear with Exit button.
NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is turned on or
when there is a change of input signal, the No Signal window will appear.
OUT OF RANGE: When input signal is non-supported timing or the video signal doesn’t have proper timing, the Out
of Range menu will appear.
NOTE:
It is possible to change the IPM settings while the “NO SIGNAL” or “OUT OF RANGE” messages are
displayed.
English-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Monitor Specifications
MultiSync E231W
Notes
LCD Module
Diagonal: 58.42 cm/23.0 inches
Viewable Image Size: 58.42 cm/23.0 inches
Active matrix; thin film transistor (TFT) liquid
crystal display (LCD); 0.265 mm dot pitch;
250 cd/m2 white luminance; 1000:1 contrast ratio,
typical (25000:1 Contrast ratio, Dynamic).
Native Resolution (Pixel Count): 1920 x 1080
Input Signal
DVI:
DVI-D 24pin: Digital RGB
DVI (HDCP)
DisplayPort:
DisplayPort Connector: Digital RGB
DisplayPort Complies with Standard V1.1a,
applicable to HDCP
VGA:
15pin Mini D-sub: Analog RGB
Sync
0.7 Vp-p/75 ohm
Separate sync.TTL level Positive/Negative
Composite sync.TTL level Positive/Negative
Sync on Green
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)
Display Colours
16,777,216
Depends on display card used.
Synchronization Range
Horizontal: 31.5 kHz to 83.0 kHz (Analog)
31.5 kHz to 83.0 kHz (Digital)
Vertical: 56.0 Hz to 75.0 Hz
Automatically
Automatically
Automatically
Viewing Angle
Left/Right:
85° (CR > 10)
Up/Down: 75°/85° (CR > 10)
Image Formation Time
Resolutions Supported
5 ms (Typ.)
720 x 400*1: VGA text
640 x 480*1 @ 60 Hz to 75 Hz
Some systems may not support all modes listed.
800 x 600*1 @ 56 Hz to 75 Hz
832 x 624*1 @ 75 Hz
1024 x 768*1 @ 60 Hz to 75 Hz
1152 x 870*1 @ 75 Hz
1280 x 1024*1 @ 60 Hz to 75 Hz
1440 x 900*1 @ 60 Hz
1400 x 1050*1 @ 60 Hz to 75 Hz
NEC DISPLAY SOLUTIONS cites recommended
1920 x 1080 @ 60 Hz............................. resolution for optimal display performance.
Active
Landscape: Horiz.: 509.18 mm/20.0 inches
Display Area
Vert.: 286.4 mm/11.3 inches
Portrait: Horiz.: 286.4 mm/11.3 inches
Vert.: 509.18 mm/20.0 inches
Power Supply
Current Rating
AC 100-240 V ~ 50/60 Hz
0.50 - 0.30 A
Power
Maximun Operation: 28 W
Consumption
Normal Operation: 23 W (Default setting)
Dimensions
Landscape: 550.1 mm (W) x 381.8 - 491.8 mm (H) x 213.9 mm (D)
21.7 inches (W) x 15.0 - 19.4 inches (H) x 8.4 inches (D)
Portrait: 329.0 mm (W) x 565.1 - 600.6 mm (H) x 213.9 mm (D)
13.0 inches (W) x 22.2 - 23.6 inches (H) x 8.4 inches (D)
Height Adjustment: 110 mm/4.3 inches (Landscape condition)
35.5 mm/1.4 inches (Portrait condition)
Weight
Environmental Considerations
Operating Temperature: 5°C to 35°C / 41°F to 95°F
6.2 kg (13.7 lbs)/Without stand: 4.2 kg (9.3 lbs)
Humidity: 20% to 80%
Altitude: 0 to 6,562 Feet / 0 to 2,000 m
Storage Temperature: -10°C to 60°C / 14°F to 140°F
Humidity: 10% to 85%
Altitude: 0 to 40,000 Feet / 0 to 12,192 m
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.
NOTE:
Technical specifications are subject to change without notice.
English-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Thin-frame design creates more desktop space for you to work and play, while the flat screen’s crisp, bright images and crystal-
clear text deliver a comfortable viewing experience.
No Touch Auto Adjust automatically adjusts your optimal image settings upon initial power-on.
Colour Control System: Allow you to change between six colour settings on your display to match your personal preference.
Redesigned OSD controls allow you to quickly and easily adjust all elements of your screen image.
NaViSet software offers an expanded and intuitive graphical interface, allowing you to more easily adjust OSD display settings
via mouse and keyboard.
Height-adjustable (110 mm) stand with tilt, swivel and pivot add flexibility to your viewing preferences.
The flat screen’s crisp, bright images and crystal-clear text deliver a comfortable viewing experience.
ErgoDesign Features: Enhance human ergonomics to improve the working environment and protect your health. Examples
include OSD controls for quick and easy image adjustments, tilt base for preferred viewing angle, small footprint and compliance
with MPRII and TCO guidelines for lower emissions.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the
monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a lower
power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and
lowering the air conditioning costs of the workplace.
Multiple Frequency Technology: Automatically adjusts the monitor to the display card’s scanning frequency, thus displaying
the resolution required.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard Mounting Interface: Allows you to connect your MultiSync monitor to any VESA standard third party mounting
arm or bracket.
Environmental Impact: The annual typical maximum operating carbon footprint of this monitor (world-wide average) is
approximately 25.5 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-
Carbon conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition).
This monitor has a manufacturing carbon footprint of approximately 35.4 kg.
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC
for its monitors.
English-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
No picture
•
•
•
•
•
The signal cable should be completely connected to the display card/computer.
The monitor does not support DisplayPort converter signal.
The display card should be completely seated in its slot.
Front Power Switch and computer power switch should be in the ON position.
Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to change graphics mode.)
•
•
•
Check the monitor and your display card with respect to compatibility and recommended settings.
Check the signal cable connector for bent or pushed-in pins.
If the front LED is dark blue, check the status of the IPM mode (see page 12).
Power Button does not respond
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
•
Image Persistence
•
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of
time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should
be turned off for one hour to erase the image.
NOTE:
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and
using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in
use.
Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)
•
Image is displayed only roughly (pixels are missing) and OSD warning “OUT OF RANGE” is displayed: Either signal
clock or resolution is too high. Choose one of the supported modes.
•
OSD warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of range. Choose one of the
supported modes.
Image is unstable, unfocused or swimming is apparent
•
Signal cable should be completely attached to the computer.
•
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total. When the
display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.
•
•
Check the monitor and your display card with respect to compatibility and recommended signal timings.
If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.
LED on monitor is not lit (no blue or amber colour can be seen)
Power Switch should be in the ON position and power cord should be connected.
•
Picture is not as bright
•
Make sure ECO MODE and AUTO BRIGHTNESS are turned off.
•
If the brightness fluctuates make sure AUTO BRIGHTNESS is turned off.
Display image is not sized properly
•
Use the OSD Image Adjust controls to increase or decrease the H. SIZE.
•
Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to change graphics mode.)
No Video
•
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
•
Some video cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC
power cord under low resolution with DisplayPort.
Brightness difference during multiple monitor usage
•
Change Auto Brightness to OFF and adjust brightness.
NOTE:
When Auto Brightness is set to ON, the monitor automatically adjusts brightness to the environment.
When condition is difference, monitor brightness will be difference.
English-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Auto Brightness function
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the
room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim
accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting
conditions.
The Auto Brightness function is set to 1 by default.
SETUP
Use the following procedure to select the Brightness Range that the monitor will use when the Auto Brightness function is
activated.
1. Set the BRIGHT level. This is the brightness level that the monitor will go up to when the ambient light level is highest.
Make sure the room is at its brightest when setting this level.
Select “1” or “3” in the AUTO BRIGHTNESS menu (Figure 1). Then use the front buttons to move the cursor up to the
BRIGHTNESS setting. Choose the desired brightness level (Figure 2).
Figure 2
Figure 1
2. Set the DARK level. This is the level of brightness that the monitor will go down to when the ambient light level is low.
Make sure the room is at its darkest when setting this level.
Then use the front buttons to move the cursor up to the BRIGHTNESS setting. Choose the desired brightness level
(Figure 3).
Figure 3
When the “Auto Brightness” function is enabled the Brightness level of the screen changes automatically according to the
lighting conditions of the room (Figure 4).
BRIGHTNESS range
BRIGHTNESS level set
for the monitor to use
when ambient lighting
level is low.
BRIGHTNESS level set for the
monitor to use when ambient
lighting level is high.
Bright condition area
room bright condition
dark
bright
Dark condition area
Screen Brightness value by Auto Brightness function
Figure 4
Lb: Border between bright and dim lighting conditions; set at factory
L1: BRIGHTNESS level set for the monitor to use when ambient lighting level is high (L1>Lb)
L2: BRIGHTNESS level set for the monitor to use when ambient lighting level is low (L2<Lb)
L1 and L2 are the brightness levels set by you to compensate for changes in ambient lighting.
English-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TCO Displays 5
Congratulations!
This display is designed for both you and the planet!
The display you have just purchased carries the TCO
Certified label. This ensures that your display is designed,
manufactured and tested according to some of the strictest
quality and environmental requirements in the world.
This makes for a high performance product, designed with
the user in focus that also minimizes the impact on the
climate and our natural environment.
TCO Certified is a third party verified program, where every product model is tested by an
accredited impartial test laboratory. TCO Certified represents one of the toughest certifications
for displays worldwide.
Some of the Usability features of the TCO Certified for displays:
• Good visual ergonomics and image quality is tested to ensure top performance and reduce
sight and strain problems. Important parameters are luminance, contrast, resolution, black level,
gamma curve, color and luminance uniformity, color rendition and image stability.
• Product have been tested according to rigorous safety standards at an impartial laboratory.
• Electric and magnetic fields emissions as low as normal household background levels.
• Low acoustic noise emissions.
Some of the Environmental features of the TCO Certified for displays:
• The brand owner demonstrates corporate social responsibility and has a certified
environmental management system (EMAS or ISO 14001).
• Very low energy consumption both in on- and standby mode minimize climate impact.
• Restrictions on chlorinated and brominated flame retardants, plasticizers, plastics and
heavy metals such as cadmium, mercury and lead (RoHS compliance).
• Both product and product packaging is prepared for recycling.
• The brand owner offers take-back options.
The requirements can be downloaded from our web site. The requirements included in this
label have been developed by TCO Development in co-operation with scientists, experts,
users as well as manufacturers all over the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in a more user-friendly direction.
Our labeling system started with displays in 1992 and is now requested by users and IT-
manufacturers all over the world. About 50% of all displays worldwide are TCO certified.
For more information, please visit
English-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer’s Recycling and Energy Information
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling
procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end
of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
Mode
Power consumption LED colour
Maximum Operation
Normal Operation
Energy Saving Mode
Off Mode
28 W
23 W (Default setting)
0.34 W
Blue
Blue
Amber
Unlit
0.32 W
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your
NEC display products, please follow the guidance of your local authority, or ask the shop where you
purchased the product, or if applicable, follow any agreements made between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local
authority so as to comply with the correct disposal method.
English-19
Download from Www.Somanuals.com. All Manuals Search And Download.
|