X-LPSV8
X-SERIES MM/MC INPUT PHONO AMPLIFIER
INSTRUCTIONS FOR USE
Thank you for purchasing the Musical Fidelity X-LPS V8 phono amplifier
This amplifier features our top quality low noise, low distortion phono stage which very closely follows the
RIAA equalisation curve for the optimum in sonic accuracy from vinyl sources. The XLPS V8 caters for both
moving magnet and moving coil cartridges to allow maximum choice when selecting a cartridge.
The X-LPS V8 is a perfect answer to most phono amplifier requirements in a single, beautifully engineered
package.
Used properly and carefully, it should give many years of outstanding musical reproduction.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents - they
may harm the surface finish.
If you have any questions about your audio system,
Please consult your dealer who is there to help and advise.
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
GENERAL ADVICE
INSTALLATION PRECAUTIONS & USER INFORMATION
This new X-LPS V8 is designed and built to provide trouble-free performance, but as with all electronic devices it is
necessary to observe a few precautions:
Heed all warnings shown on the back of the product.
Only connect the X-LPS V8 power supply to a mains outlet having the same voltage as marked at the back of
the power supply.
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is switched
off.
Position the power lead and signal interconnects where they are not likely to be walked on or trapped by items
placed on them.
Do not use near water, or place water-filled containers on the X-LPS V8, for example, a flower vase or potted
plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform
your dealer, who should then check the unit before further use. Entry of liquid into the X-LPS V8 is
dangerous, and may cause electric shock or fire hazard.
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you
can replace yourself. Refer all service work to an authorised Musical Fidelity agent.
Note: Unauthorised opening of the equipment will invalidate any warranty claim.
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they may
harm the surface finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by
lightning. For protection of the audio system during electrical storms, remove the mains plugs and disconnect any
aerial lead.
If after-sales service is required, to help the dealer identify the X-LPS V8 please quote the serial number located on the
rear panel of the unit.
Issue 1
Page 3 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
ITEM DISPOSAL INFORMATION
DISPOSAL
AFVAL
The crossed out wheeled bin label that appears on the
back panel of the product indicates that the product must not be
disposed of as normal household waste. To prevent possible harm
to the environment please separate the product from other waste to
ensure that it can be recycled in an environmentally safe manner.
Please contact local government office or retailer for available
collection facilities.
Het label op de achterzijde van dit apparaat, een
afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit
apparaat niet samen met gewoon huishoudafval mag worden
weggegooid. Om mogelijke schade aan onze leefomgeving te
voorkomen dient dit apparaat, gescheiden van gewoon
huishoudelijk afval, te worden afgevoerd zodat het op een
milieuvriendelijke manier kan worden gerecycled. Neem voor
beschikbare inzamelplaatsen contact op met uw gemeentelijke
reinigingsdienst of met uw elektronica leverancier.
DISPOSITION
La poubelle sur roulettes barrées X, qui apparaît en logo
sur le panneau arrière du produit, indique que celui-ci ne doit pas
être traité comme un déchet domestique commun. Afin de protéger
l'environnement, ce produit électronique devra être géré
séparément et donc recyclé selon les nouvelles normes
Européennes Rohs concernant les déchets d'appareils électroniques.
Prière de contacter les services concernés gouvernementaux ou
votre point de vente pour l'élimination et l'enlèvement de déchets
électroniques équipés de composants électroniques.
HÄVITTÄMINEN
Yliruksattua jäteastiaa kuvaava tarra tuotteen
takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä
erillään muusta jätteestä ja se on kierrätettävä ekologisesti
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan
Ympäristökeskukseen lähimmän kierrätyskeskuksen löytämiseksi.
AFSKAFNING
DISPOSAL
Logoet med en skraldespand med kryds over på bagsiden
af apparatet indikerer at dette produkt ikke må kasseres som normal
husholdningsaffald. For at forebygge mulig skade på miljøet, bedes
De separere dette produkt fra andet affald, og sikre at det bliver
genbrugt på en miljørigtig måde. Kontakt venligst de lokale
myndigheder eller din forhandler for oplysning om nærmeste
tilgængelige opsamlingssted for elektronikaffald.
La etiqueta cruzada hacia fuera del compartimiento que
aparece en el panel trasero del producto indica que el producto no
se debe reciclarse como basura normal de la casa. Para prevenir
daños posible al ambiente separe por favor el producto de otras
basura para asegurarse de que puede ser reciclada de una manera
ambientalmente segura. Entre en contacto por favor a su oficina
gubernamental local o a su minorista para las instalaciones
disponibles de la colección.
∆ΙΑ∆ΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ
ΤΟ
ΣΗΜΑ
ΜΕ
ΤΟΝ
∆ΙΑΓΕΓΡΑΜΜΕΝΟ
RIFIUTI
ΤΡΟΧΗΛΑΤΟ ΚΑ∆Ο ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ ΟΨΗ
ΤΟΥ ΜΗΧΑΝΗΜΑΤΟΣ
L'etichetta del cassonetto barrato riportato sul retro
dell'apparecchio indica che il prodotto non deve essere smaltito
tramite la procedura normale di smaltimento dei rifiuti domestici.
Per evitare eventuali danni all'ambiente, separare questo prodotto
da altri rifiuti domestici in modo che possa venire riciclato in base
alle procedure di rispetto ambientale. Per maggiori dettagli
sulle aree di raccolta disponibili, contattate l'ufficio govenativo
locale od il rivenditore del prodotto.
∆ΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ∆ΕΝ ΠΡΕΠΕΙ ΝΑ
∆ΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝ∆ΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ
ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ
ΑΛΛΑ
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ
ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ
FACHGERECHTE ENTSORGUNG:
ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ
Η
ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ
Das auf der Geräterückseite angebrachte Label deutet
darauf hin, dass das Produkt nicht mit konventionellem
Hauskehricht entsorgt werden darf. Um Schäden und
Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das
Produkt fachgerecht entsorgt und von anderem Abfall getrennt
werden. Wenden Sie sich bei Fragen hierzu an Ihren Fachhändler
oder an eine öffentliche Informationsstelle.
ΑΓΟΡΑΣ ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.
Issue 1
Page 4 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
INSTALLATION
INTRODUCTION
POWER CONNECTIONS
Congratulations on the purchase of the new X-LPS V8 phono
preamp. Great attention has been paid to internal layout,
isolating each circuit section to prevent possible interaction.
The unit features our highly refined low noise input amplifier
circuit coupled with a low output impedance close tolerance
RIAA stage to improve record delivery and dynamics. Two
types of cartridge are catered for, moving magnet and moving
coil, to allow full choice in selecting preferred cartridge type
for the system.
The X-LPS V8 requires a free mains socket for its power
supply. The power supply then connects using its flying lead
to the DIN 24V AC socket at the back of the unit. We advise
that you use only the supplied X-series adaptor for this unit,
or a suitable Musical Fidelity power supply.
AUDIO CONNECTIONS
Inputs: Connect turntable cartridge input to RCA MM or MC
inputs as required.
(see p.7 For more information). Use good quality fully
connected (signal and ground) coaxial phono cables for all
signal connections.
The resultant performance achieved by this unit is among the
best in the world. It has excellent signal to noise ratio, low
distortion, wide bandwidth, huge dynamic range,
extraordinary resolution and fine detail.
Grounding post: Connect turntable ground lead (if present)
to green earthing post. The post accepts bare wire, spade
connectors or 4mm banana plugs.
NB grounding apparatus in a system can sometimes
aggravate rather than alleviate hum; some experimentation
may be necessary to obtain ultimate noise levels. Remember
especially with MC input, the X-LPS V8 is an extremely
sensitive amplifier!
CLEANING
Before cleaning the unit, switch off power at the mains switch
and remove the mains plug from the wall socket.
Clean the cabinet and remote control unit using a moist cloth.
Using solvents, white spirit or thinners is not advised, as they
could damage the surface finish.
INSTALLATION
Outputs: Connect output sockets to a LINE level input e.g.
AUX input on the amplifier/preamplifier.
The X-LPS V8 outputs provide a highly amplified LINE level
signal and MUST NOT be connected to a PHONO input
Position the X-LPS V8 on a stable, horizontal surface where
there is no risk of it being knocked, or subjected to vibration
such as from loudspeakers.
The X-LPS V8 must be protected from humidity - if the unit
is moved from a cold place to a warm room, leave the unit for
an hour or so to allow sufficient time for the moisture to
evaporate.
Issue 1
Page 5 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
1. POWER LED
2
FACILITIES AND CONNECTION
UNIT FRONT PANEL
1
UNIT REAR PANEL
3
4
5
6
7
2. EARTH 4mm banana post
3. MM/MC Switch
5. MC INPUT RCA sockets
6. OUTPUT RCA sockets (line level)
4. MM INPUT RCA sockets
7. POWER SUPPLY Input din socket
Issue 1
Page 6 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
AMPLIFIER OPERATION
STARTING
Once all connections are made, the power LED on the
front panel will light, indicating unit is ready for use.
PHONO IN (MM)
To use the phono input connect MM cartridge to MM
input. Press back panel switch to the MM position (out).
PHONO IN (MC)
To use the phono input connect MC cartridge to MC
input. Press back panel switch to the MC position (in).
IN USE
The X-LPS V8 has been designed to be left on
indefinitely, but please note the mains adaptor may
become warm to the touch, this is normal.
If switching the X-LPS on or off or changing the
MM/MC switch, please ensure the volume is turned
down on the following amplifier. This will avoid
unwanted noises in the speaker due to the high
sensitivity of the X-LPS V8.
Issue 1
Page 7 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
AMPLIFIER PROBLEMS?
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always
check the most obvious possible causes first, such as the following examples:
Problem
Probable Cause
Remedy
Plug in securely
No power
No sound
Mains power supply is not fully
inserted into mains socket
Mains power supply lead is not fully
inserted into rear socket
Wrong connections between input
sources and the unit
Check audio input lead connections
Check cartridge wiring
Cartridge incorrectly wired
Sound is not precise, lacking in bass
and stereo image
Cartridge incorrectly wired
Double-check cartridge wiring using
cartridge and turntable
manuals/wiring diagrams.
Input connector plugs not fully
pushed in
Check plugs are inserted fully and
securely
Output connector plugs not fully
pushed in
Hum
Turntable not earthed and needs
earthing
Check turntable earthing lead is
connected to earthing post on XLPS
V8
Disconnect Earthing lead from
earthing post
Turntable already earthed and makes
hum loop in system
Insert plug securely
Audio connector plug not fully
pushed in
Check cable is connected at both
ends.
Cable Fault
N.B. some esoteric cables have
internal wiring intentionally
disconnected/modified. For best
results on all inputs AND outputs,
please use good quality screened
coax; fully connected signal-to signal,
screen-to-screen.
Unsuitable Cable
(e.g. cable grounds not connected)
Plop Heard in speakers when
switching on or off or changing
MM/MC switch
High gain of XLPS V8 amplifying
circuit transients.
Not a fault.
Please ensure volume level on
amplifier is turned down if switching
the XLPS V8 on or off or changing
cartridge type switch whilst
connected.
If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent.
Remember; never open the case of the X-LPS V8, as this will invalidate the guarantee.
Issue 1
Page 8 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
AMPLIFIER SPECIFICATIONS
MM input:
Input response:
RIAA/IEC combined, see graph
Input sensitivity
Input impedance
3mV for 350mV out
47K Ohms
THD + N, 1KHz, 350mV out
Overload margin
<0.01% typical
28dB
Signal/noise ratio
>100dB ‘A’-weighted
MC input:
Output:
Input response:
Input sensitivity
Input impedance
THD + N, 1KHz, 350mV out
Overload margin
RIAA/IEC combined, see graph
350µV for 350mV out
100 Ohms
<0.01% typical
28dB
Signal/noise ratio
>100dB ‘A’-weighted
Pre-out impedance
RIAA accuracy
50 Ohms
±0.25 dB 20Hz to 20KHz
2 0 .0
1 5 .0
1 0 .0
5 .0
P H O N O R E S P O N S E
0 .0
d B
RIA A
- 5 .0
P HO NO
RIA A /IEC
- 1 0 .0
- 1 5 .0
- 2 0 .0
2 0 .0
3 1 .5
5 0 .0
8 0 .0
1 2 5
2 0 0
3 1 5
5 0 0
1 0 0 0
1 6 0 0
2 5 0 0
4 0 0 0
6 3 0 0 1 0 0 0 0 1 6 0 0 0
F re q u e n c y (H z )
Nominal phono response
Connections:
Moving magnet
input:
1 pairs MM level RCA connectors,
Moving coil input:
Line level outputs:
Earth post:
1 pairs MC level RCA connectors,
1 pair RCA line level fixed RIAA
1 4mm banana plug/binding posts
Power
requirement:
12-0-12V (24V total) Using mains adaptor (supplied)
AC at 500mA
Standard
Power Supply Unit
T48A-24-500-3
1 off
accessories:
Dimensions:
Weight:
Main unit
180 mm 7 inches
88 mm
240 mm 9 ½ inches
Wide
High including feet
Deep including terminals
3 ½ inches
1.55 kg, 3 ½ lbs
Unboxed
2.15 kg
4 ¾ lbs
Boxed unit including power supply and all accessories
Musical Fidelity reserves the right to make improvements which may
result in specification or feature changes without notice.
Issue 1
Page 9 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
X-LPSV8
MANUAL REVISION
RELEASE
DATE
CHANGES
Issue 1
30th October 2007
Issue 1
Page 10 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|