Millennium Enterprises Stereo Amplifier Integrated Modeling Amplifier User Manual
Integrated Modeling Amplifier  
User ’s Guide  
Please visit Johnson Amplification on the World Wide Web at http://www.digitech.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
DECLARATION OF CONFORMITY  
Manufacturer’s Name:  
Manufacturer’s Address:  
Johnson Amplification  
8760 S. Sandy Parkway  
Sandy, Utah 84070, USA  
declares that the product:  
Product Name:  
Johnson Millennium Stereo 250 Head  
Product Options:  
All  
conforms to the following Product Specifications:  
Safety:  
EN 60065 (1993)  
IEC 65 (1985) with Amendments 1, 2 & 3  
EMC:  
EN 55013 (1990)  
EN 55020 (1991)  
Supplementary Information:  
The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and EMC  
Directive 89/336/EEC as amended by Directive 93/68/EEC.  
.
Johnson Amplification  
President of Johnson Amplification  
8760 S. Sandy Parkway  
Sandy, Utah 84070, USA  
Tel: 801.566.8800  
Fax: 801.566.7005  
Effective December 19, 1997  
European Contact: Your Local Johnson Amplification Sales and Service Office or  
International Sales Office  
3 Overlook Drive #4  
Amherst, New Hampshire 03031, USA  
Tel: 603.672.4244  
Fax: 603.672.4246  
I
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Quick Start  
For those of you who prefer to play now and read later, we've included this Quick Start section to get you up and running.  
Connect Cables:  
Connect guitar into the Bright or Normal input jacks. Connect an un-shielded speaker cable to the extension speaker cabinet outputs (located  
on the rear panel of the Millennium) and run into the desired extension speaker cabinet (such as the Johnson Amplification J212 or J412) with  
a 4 ohm minimum load resistance requirement per channel.  
Connect J-3 Multi-Function Footswitch:  
Connect the included J-3 Footswitch to the J-3 insert jack on the rear panel of the Millennium. The three footswitches can be programmed to  
perform several functions. From the factory, the footswitches will A-B Channel Switch and change presets Up and Down. For information about  
the J-3 Footswitch please refer to page 67.  
Connect Johnson Amplification J-12 Foot Controller (if applicable)  
Connect the output of the optional Johnson Amplification J-12 to the Foot Controller jack found on the rear of the Millennium. Make sure that  
connection is made before applying power to the Millennium.  
WARNING: DO NOT CONNECT ANYTHING BUT THE OPTIONAL JOHNSON AMPLIFICATION J-12 OR DIGITECH CONTROL ONE  
FOOT CONTROLLER TO THE FOOT CONTROLLER JACK ON THE REAR PANEL! DOING SO MAY DAMAGE THE DEVICE.  
MIDI control of the Millennium can be done by connecting MIDI controller devices to the MIDI In jack on the rear panel.  
Apply Power:  
Note: When applying power to the Millennium, it is recommended that the <Input> and <Master Volume> knobs be turned down prior to  
powering up the unit.  
Adjust Input and Output:  
Use the <Input> level knob on the front panel to adjust the input level, so that the loudest guitar signal occasionally lights the clip LED  
indicator. Now adjust the <Master Volume> level knob on the front panel of the Millennium to the desired output level .  
Select Speaker Output Voicing:  
Page 1 of the Utility menu lets you select the speaker cabinet voicing to be used whether it be a 4x12 or 2x12. This selection can be done by  
simply pressing the <Utility> button, and then turn the <Page> knob until you reach page 1. At this point, use the <3> knob to select either  
the 4x12 or 2x12 speaker cabinet voicing. Once the selection has been made, press the <Preset> button to return to Preset mode.  
Select Preset:  
Begin playing your guitar, and choose any preset using the <Preset/Effect> wheel. User Presets 1-100 are duplicates of the Factory Presets.  
They are user-programmable. You can modify and store them as you want. Factory Presets 1-100 are not user-programmable and cannot be  
overwritten.  
II  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Table of Contents  
Declaration of Conformity................................................................i  
Quick Start........................................................................................ii  
Table of Contents ............................................................................iii  
Section 2 - Setting Up  
Safety Information  
Making Connections......................................................................13  
Millennium into Extension Speaker Cabinets ............................13  
Millennium direct with the XLR Programmable Speaker Cabinet  
Emulator ......................................................................................14  
Getting Around the Operating System........................................15  
Preset Mode..................................................................................15  
FX Edit Mode................................................................................15  
Utility Mode..................................................................................15  
Assign Mode ................................................................................15  
Getting Sounds ..............................................................................16  
Selecting A Preset ..........................................................................19  
Using the Tuner..............................................................................19  
Section 1 - Introduction  
Congratulations................................................................................1  
Included Items..................................................................................1  
Product Features ..............................................................................1  
Warranty ..........................................................................................2  
A Quick Tour of the Millennium..................................................3  
The Front Panel............................................................................3  
The Rear Panel..............................................................................7  
Integrated Amplifier Modeling ....................................................8  
A-B channel switching ................................................................8  
The Digital Effects Section ..........................................................9  
Digital Effects ..........................................................................9  
Real-Time Modifiers ................................................................9  
Basic Specs................................................................................10  
Programmable FX Loop ............................................................10  
Signal Flow................................................................................10  
Foot Controller Compatibility......................................................11  
Module Types ..............................................................................12  
Module Sizes ................................................................................12  
Section 3 - Editing Presets  
Naming/Storing Presets ................................................................21  
Editing a Preset ..............................................................................23  
Editing Integrated Amplifier Modules ........................................23  
Editing the Analog Wah Module ..................................................25  
Editing the Noise Gate module....................................................26  
Selecting FX Configurations ........................................................27  
Editing Digital FX ........................................................................27  
Changing Effect Modules ............................................................28  
Selecting Effect Defaults ..............................................................28  
Adjusting FX Module Parameters ................................................28  
Custom Defaults ..........................................................................28  
Comparing Changes ....................................................................29  
III  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section 4 - Editing Modules  
Section 5 - Advanced Topics  
Storing/Naming Defaults ..................................................................30  
Editing a Module..............................................................................31  
Output Module Functions................................................................32  
Effect Module Size and Type List ....................................................33  
Effect Default List ............................................................................34  
Assigning Modifiers ..........................................................................56  
MIDI CC........................................................................................56  
LFO ..............................................................................................56  
Dynamic........................................................................................56  
External Expression Pedals ..........................................................57  
Linking a Parameter to a Modifier ..............................................57  
Setting up an LFO and a Dynamic Modifier ................................58  
Morphing Pedal Assignments ......................................................59  
Volume Pedal Assignment............................................................60  
MIDI Functions  
Effect Library................................................................................35  
Amplifier Section  
Analog Wah ..................................................................................35  
Amplifier Models ..........................................................................35  
Noise Gate....................................................................................36  
Digital Effects Section  
Reverbs ........................................................................................37  
Chorus & Flangers........................................................................40  
Phasers ........................................................................................44  
Rotary Speaker Simulator ............................................................45  
Tremolo & Auto Panner ..............................................................46  
Pitch Shifters ................................................................................47  
Detuners ......................................................................................48  
Delays ........................................................................................50  
Equalizers ....................................................................................51  
Multi Effect Modules ....................................................................53  
Whammy Effects ..........................................................................54  
Auto Wah......................................................................................55  
MIDI Channels ............................................................................62  
MIDI Merging ..............................................................................62  
MIDI Receive Map ........................................................................62  
MIDI Transmit Map......................................................................62  
SysEx Device Channels ................................................................63  
SysEx Dumps................................................................................64  
Preset Dump ................................................................................64  
Bulk Dump ..................................................................................65  
System Dump ..............................................................................65  
Other Utility Functions  
Resetting to Factory Settings........................................................66  
Global-Local Cabinet Emulator....................................................66  
Output Mode and Speaker Cabinet Voicing Selections ..............67  
J-3 Footswitch Set-Up ..................................................................67  
IV  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section 6 - Using the Johnson Amplification J-12  
Foot Controller  
SysEx Implementation Guide ......................................................89  
MIDI Basics ..........................................................................89  
General Format ....................................................................90  
Procedures ............................................................................90  
Request One Preset - 01(h) ..................................................91  
Receive One Preset - 42(h) ..................................................91  
Request Bulk Dump - 49(h) ................................................91  
Receive Bulk Dump - 57(h)..................................................91  
Request Utility Settings - 11(h) ............................................91  
Receive Utility Settings - 12(h) ............................................92  
Request Parameter Value - 17(h)..........................................92  
Receive Parameter Value - 18(h) ..........................................92  
Request All Current Parameter Values - 23(h) ....................92  
Receive All Current Parameter Values for current preset ....93  
Request Module Configuration-25(h) ..................................93  
Respond Module Configuration-26(h) ................................93  
Receive Key Scan Code - 54(h) ............................................94  
Receive Key Accepted - 56(h) ..............................................94  
Select One Preset - 1F(h)......................................................94  
Reset Preset - 20(h) ..............................................................95  
Reset Device - 21(h)..............................................................95  
Reset Factory Settings - 22(h) ..............................................95  
Request User Defaults - 13(h) ..............................................95  
Receive User Defaults - 14(h) ..............................................95  
Key Scan Codes ....................................................................96  
SysEx Preset Dump Example................................................97  
FX Modules and Parameter Codes ......................................98  
Configuring the Pedalboard ............................................................68  
Connecting the J-12 ....................................................................68  
Expression Pedal Names ..............................................................68  
Assigning Functions ....................................................................69  
Preset to Footswitches ................................................................69  
Parameters to Footswitches/Expression Pedal ............................70  
Other Footswitch Functions ........................................................71  
Assigning MIDI Control to the Exp. Pedal ..................................71  
Toggle MIDI CC ..........................................................................71  
Assigning CC Numbers to Expression Pedals..............................72  
CC Transmit Channel ..................................................................73  
Other Pedalboard Tidbits ............................................................75  
Bank Up/Tuner & Bank Down/Bypass Footswitches..................75  
Using the Tuner ..........................................................................75  
Naming Banks ..............................................................................75  
UnLinking or Viewing Assignment Links ....................................76  
Section 7 - Appendix  
Factory Preset List ........................................................................77  
Preset Descriptions ......................................................................79  
Effect Configuration Chart ..........................................................85  
Harmony Interval Charts..............................................................86  
Specifications................................................................................87  
MIDI Implementation Chart ........................................................88  
V
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
VI  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
Section-1 Introduction  
Congratulations...  
... you are now the proud owner of a Johnson Millennium Stereo 250 Amplifier Head, the most powerful, flexible, and easy-to-use Integrated Modeling  
Amplifier ever produced. Your Millennium has set the new standard for all other Amplifiers/Multi-effect processors to follow.  
This owner's manual is your key to understanding the powerful world of the Millennium. Read it carefully. After you've had time to familiarize yourself  
with the unit, try experimenting with unusual effect combinations. You are certain to achieve sounds never thought possible before. Good luck, and  
Thank you very much for choosing Johnson Amplification.  
Your Millennium was carefully assembled and packaged at the factory. Before you proceed any further, make sure the following items are included:  
• (1) Owner’s Manual  
• (1) Johnson Amplification Millennium Stereo 250 Amplifier Head  
• (1) J-3 Multi-Function Footswitch  
• (1) Johnson Amplification warranty card  
Please save all packing materials. They were designed to protect the unit from damage during shipping. In the unlikely event that the unit requires  
service, use only the factory supplied carton to return the unit.  
Millennium Features:  
• 250Watts (125 per side) power- amp section  
• Exclusive Johnson Amplification Integrated Amplifier Modeling  
which instantly lets you access some of most popular Vintage and  
Modern Amplifier types available  
• Exclusive Dynamic Parameter Control  
• Programmable Speaker Cabinet Emulator XLR outputs  
• Chromatic tuner  
• Full MIDI Implementation  
• Dual Tube Preamp Section (12AX7)  
• Full bandwidth effects (20-20kHz)  
• All effects and parameters available for MIDI continuous control  
• 2 Expression Pedal insertion jacks to add external Expression  
pedals for additional assigning options  
• 24-bit signal path, 48-bit internal data path  
• Up to 4 digital effects at once  
• A-B Channel switching  
• S-DISC II ® Processing  
• J-3 Multi-function footswitch (included)  
• Flexible, easy-to-use effect routing  
• Upgradable System Software (via the MIDI In port)  
• Optional Johnson Amplification J-12 foot controller with 2 built-in  
Expression Pedals for ultimate programmability and control.  
• Effects can be repeated in a chain,  
(e.g. EQ + flange + EQ + pitch shift)  
• Instant module access  
1
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
We at Johnson Amplification are very proud of our products and back-up each one we sell with the following warranty:  
1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty.  
2. Johnson Amplification warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship  
under normal use and service.  
3. Johnson Amplification liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect,  
provided the product is returned to Johnson Amplification WITH RETURN AUTHORIZATION, where all parts and labor will be covered  
up to a period of one year. A Return Authorization number may be obtained from Johnson Amplification by telephone. The company  
shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly.  
4. Proof-of-purchase is considered to be the burden of the consumer.  
5. Johnson Amplification reserves the right to make changes in design, or make additions to, or improvements upon this product without  
incurring any obligation to install the same on products previously manufactured.  
6. The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone other than a  
certified Johnson Amplification technician or, if the product is used with AC voltages outside of the range suggested by the  
manufacturer.  
7. The foregoing is in lieu of all other warranties, expressed or implied, and Johnson Amplification neither assumes nor authorizes any  
person to assume any obligation or liability in connection with the sale of this product. In no event shall Johnson Amplification or its  
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond  
their control.  
Johnson Amplification™, S-DISCII™, Whammy™, and Silencer II™ are registered trademarks of the Harman Music Group Incorporated.  
NOTE: The information contained in this manual is subject to change at any time without notification. Some information contained in this  
manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was  
completed. The information contained in this version of the owner's manual supersedes all previous versions.  
2
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
A Quick Tour of the Millennium Two-Fifty  
The Front Panel  
1
2 3  
4 a-e  
5 a-f  
6 7  
8
9
10  
11 a-f  
12 13 14 15 16  
17-a-f  
18  
1) Bright and Normal Inputs - The 1/4” inputs of the Millennium allow you to select between Bright (top) and Normal (bottom). The Bright  
input produces a slightly brighter sound, where as the Normal input provides a normal input color.  
2) Input Level Control - This knob controls the overall input level of the Millennium. A recommended setting for this knob would be to turn  
the level up enough so that the Millennium Clip LED occasionally lights.  
3) Clip LED- This Clip LED tells you that the input level is set too high and there is internal input level clipping.  
4) Amp Controls- These 5 knobs control all of the amplifier EQs and levels. These controls are as follows:  
4a) Gain - This knob controls the overall distortion gain level of the Amplifier models that use distortions, and controls the volume of the  
amplifier models that have clean tones. Values range from 0.0 to 10.  
4b) Treble - This knob is used to control the Treble frequency of the currently selected preset. Values range from 0.0 to 10.  
4c) Mid - This knob is used to control the Mid frequency of the currently selected preset. Values range from 0.0 to 10.  
4d) Bass - This knob is used to control the Bass frequency of the currently selected preset. Values range from 0.0 to 10.  
Amplifier EQ Note: Due to the special Integrated amplifier modeling features of the Millennium, every time a different  
Integrated Amplifier model is called up, the EQs take on the characteristics of the selected Amplifier models. Some of the  
Amplifier models do not use certain tone controls (ie: Matchless), have a dash in the display, indicating that the frequency is  
not available.  
4e) Level - This knob is used to control the overall output level of the currently selected preset. Values range from 0.0 to 10.  
3
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section 1 Introduction  
5) Amplifier Model Buttons- These buttons let you instantly select any one of the Integrated Amplifier models and switch channels within  
the currently selected Amplifier model setting. The buttons are as follows:  
5a) American Stack - This button is used to instantly call up the American Stack amplifier models.  
5b) British Stack - This button is used to instantly call up the British Stack amplifier models.  
5c) Johnson - This button is used to instantly call up the Johnson Amplifier Custom amplifier models.  
5d) American Combo - This button is used to instantly call up the American Combo amplifier models.  
5e) British Combo - This is used to instantly call up the British Combo amplifier models.  
5f) A-B Channel switcher - This button allows you to channel switch within the selected Amplifier models.  
6) A-B Channel LED indicators - These two LEDs indicate which channel of the selected Amplifier Model is being used.  
7) Contour Control - This knob is used to control the tone contour within the power amp section of the Millennium.  
8) Master Output - This knob is used to globally control the overall output of the Millennium.  
9) Display - This large custom display is where you receive most of the information you need to optimize performance of the Millennium. This  
display has several functions and they are as follows:  
9-a  
9-e  
9-d  
ꢀ
ꢀ
Sweet Combo  
1
%kHz  
msdB  
%kHz  
50  
msdB  
6ꢀ0%kHz 70%kHz 100  
2
msdB 3  
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
100  
USER  
BANK  
9-h  
9-b  
#
b
CLIP  
PAGE  
10  
OF11  
9-c  
9-f  
9-g  
9a) Preset Number - The three large digits located in the upper left corner of the display indicate which preset is currently selected. This  
indicator will also display the currently selected note while the Millennium is in Tuner mode.  
9b) Factory / User indicators - Located directly below the preset number, the Factory and User preset icons indicate whether the current  
preset resides in the Factory or User bank. To toggle between the Factory and User presets simply press the <Preset> button.  
9c) Bank / Page Indicators - Located in the bottom left hand corner of the display, the Bank/Page indicators display:  
• The J-12 Bank number in which the current program resides in Preset Mode (Note: This is only displayed when the Johnson  
Amplification J -12 foot controller is connected).  
• The page which is currently selected in various editing modes.  
4
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
9d) Information Line - The row of 24 characters in the top line of the display indicates more detailed information about specific  
functions and items such as: preset names, parameter names and utility information.  
9e) Parameter Data Sections - Immediately below the information line, are four parameter data sections. They correspond with knobs  
<1> through <4> on the front panel. Each section displays the current value of the indicated parameter.  
A LINK icon in each group tells whether the indicated parameter is linked for expression control. When a parameter has been  
modified, the CHANGED icon will appear under the parameter that has been modified and the <Store> button will light to  
indicate a change has been made to the preset, but not stored.  
9f) Input Level / Clip Meters / Tune Indicator- An input level and clip meter is located in the bottom center of the display. This meter  
shows the guitar signal level, and uses a peak detector action to display the highest levels at the input. The CLIP icon at the end of  
the meter, indicates if the the input signal is being clipped at the Analog input section (pre-digital). The DIGITAL CLIP icon  
indicates that there is clipping in the digital effects domain. This meter is also used to show note activity while the Millennium is in  
Tuner mode  
9g) Effect Routing Matrix - The Effect routing matrix shows the signal flow of the currently selected preset through the amp and effect  
sections. This matrix includes boxes that represent each effect module along with lines that indicate how those effects are connected to  
inputs, outputs and each other. If an effect module is bypassed, a line appears through that module's box in the matrix.  
Note- When in FX Edit mode, the box that represents the currently selected effect module will flash.  
9h) Speaker Cabinet Emulator Icon - When the SPEAKER icon appears in the display, this indicates that the Speaker Cabinet  
Simulator is engaged in the XLR outputs located on the rear panel.  
10) Preset/Effect Wheel - Changes presets (in Preset Mode) or selects effect modules (in FX Edit Mode).  
11 a-f) Function Buttons - These 6 buttons are used for primary functions and edits of the Millennium. Their functions are as follows:.  
11a) Preset Button - This button always puts the Millennium in Preset mode with a single press. Pressing the <Preset> button while in  
Preset mode toggles between User and Factory bank presets.  
11b) FX Bypass - This button when pressed bypasses all digital effects in the Millennium.  
11c) Utility - This button when pressed enters the Utility mode of the Millennium.  
11d) FX Edit - This button when pressed, the Millennium enters the Wah module or the last edited module.  
11e) Assign - This button is used to assign parameters to the J-12 footswitches, MIDI control and dynamic modifiers.  
11f) Store - This button is used to copy and/or store and name modified presets.  
12) Mix/Page Knob - This button controls the effect mix level of the Millennium when it is in Preset mode. When the Millennium is in Edit  
or Utility mode, this button takes you to the next or previous page of the selected menu.  
5
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
13) Speed/1 Knob - This knob controls the Speed of modulation effects when the unit is in Preset mode. In Edit or Utility mode, it controls  
the number 1 parameter that appears in the display.  
14) Depth/2 Knob - This knob controls the depth of modulation effects when the unit is in Preset mode. In Edit or Utility mode, it controls  
the number 2 parameter that appears in the display.  
15) Delay/3 Knob - This knob controls the overall level of Delay when delay is used in the selected preset. In Edit or Utility mode, it controls  
the number 3 parameter that appears in the display.  
16) Reverb/4 Knob - This knob controls the overall level of Reverb when a Reverb module is used in the selected Preset. In Edit or Utility  
mode, it controls the number 4 parameter that appears in the display.  
17 a-f) FX Library Buttons:  
17a) [Config] - Enters Edit mode at the configuration screen. You can use the <Speed/1> knob to select any one the 15 different effect con-  
figurations.  
17b) [Mod] - Enters Edit mode and selects the first available Modulation module in the preset. Successive presses move to the next available  
Modulation module. Pressing and Holding the button while editing an effect will load the first Modulation effect in the effect list.  
Modulation effects available: Dual Chorus, Quad Chorus, Octal Chorus, Dual Flange, Dual Phaser, Rotary Speaker Simulator, Stereo  
Tremolo, Auto Panner, Chorus/Delay and Flange/Delay.  
17c) [Delay] - Enters Edit mode and selects the first available Delay module in the preset. Successive presses move to the next available Delay  
Module. Pressing and Holding the button while editing an effect will load the first Delay effect in the effect list. Delay Effects available:  
Delay, Dual Delay, Quad Delay, Stereo Delay, Stereo Dual Delay, Stereo Quad Delay, Long Delay, Analog Delay, Stereo Analog Delay,  
Chorus/Delay and Flange/ Delay.  
17d) [Reverb] - Enters Edit mode and selects the first available Reverb module in the preset. Successive presses move to the next available  
Reverb module. Pressing and holding the button while editing an effect will load the first Reverb effect in the effect list. Reverb Effects  
available: Pre Delay, Reverb, Dual Reverb, Stereo Dual Reverb, Stereo Reverb, Gated Reverb, Spring Tank and Room Echo.  
17e) [Other] - Enters FX Edit mode and selects the first available digital effect module not included in above selections. Successive presses  
move to the next available digital effect module. Pressing and holding the button while editing an effect will load the first modulation  
effect in the effect list. Modules available in the Other section: Dual Detune, Quad Detune, Octal Detune, Smooth Pitch Shift, Dual  
Pitch Shift, Quad Pitch Shift, Octal Pitch Shift, Stereo Pitch Shift, Stereo Dual Pitch Shift, Whammy, Harmony, Compressor, Auto Wah, GEQ  
8, GEQ 15, GEQ 31, St GEQ 8, PEQ 3, PEQ 6 and St PEQ 6.  
17f) [TapIt] -The TapIt button is used to set the delay time of repeats. To use the TapIt button, simply press the <TapIt> button twice at the  
desired tempo and the delay module will automatically recalibrate the delay time. A great option with the TapIt delay time function is  
that the TapIt function can be assigned to be controlled by a footswitch on the J-3 or J-12 foot controllers.  
18) Power Switch - Turns the unit on and off. It is always a good idea to turn the Master Volume output down when applying power or  
shutting the Millennium down  
6
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
The Rear Panel  
7
10  
9
3
4
5
6
8
1
2
MIDI  
In Out/Thru  
Expression Pedal  
J3  
1
2
Footswitch  
Right Speaker  
Left Speaker  
FX Send  
FX Return  
Left  
Right  
Speaker Output (4 Ohms Minimium)  
Direct/Record  
Output  
J12  
1) Fuse- 100, 120 VAC 6 Amp fuse is inserted here.  
2) Expression Pedal 1 and 2 Jacks - This is the insert point for an external expression pedal. Standard volume or Voltage controller pedals  
can be used in these inserts. Once inserted, this expression pedal can be linked to control any parameter of the Millennium. For more  
about assigning expression pedals, see pg. 57.  
Notice: When using the Millennium with the Johnson Amplification J-12 foot controller, the 1/4” Expression pedal inputs on the rear of the  
unit are referred to as EXP 3 and EXP4. When the Millennium is used alone, the expression pedal inputs are referred to as EXP 1 and EXP 2.  
3) MIDI In - The MIDI IN port allows the Millennium to respond to incoming MIDI information.  
4) MIDI Out/Thru - This port allows the Millennium to send out or pass MIDI data to other devices.  
5) J-3 Footswitch Jack - This is the insert point for the J-3 multi-function footswitch.  
6) Johnson Amplification J-12 Foot Controller Input - This is a 5-pin DIN plug for connecting the optional Johnson Amplification J-12 foot  
controller. Connection of the J-12 should be made before the Millennium is turned on.  
IMPORTANT: CONNECTING A DEVICE OTHER THAN THE J-12 OR CONTROL ONE CAN DAMAGE THE UNIT.  
7) Left and Right Extension Speaker Outputs - These 4 outputs are used to connect speaker cabinets. Up to 4 extension speaker cabinets  
can be connected to the Millennium. Make sure that the extension cabinet being connected has at least a 4 ohm load resistance per  
channel. The ohm load resistance effects how much power the extension cabinet receives from the Millennium.  
8) Direct XLR Outputs - These XLR outputs are used for recording direct or for sending the output signal to a live mixing console.  
9) Loop Return Jack - This is the effects loop mono return jack. Connect the output of an external effect device here.  
10) Loop Send Jack - This is the effects loop send jack.  
7
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -1 Introduction  
Integrated Amplifier Modeling  
Vintage and Modern Amp Models: There is really no need to have numerous vintage or modern amplifiers in storage or cluttering up space.  
The Millennium's unique Integrated Amplifier modeling puts almost every amplifiers’ tone under the hood. This feature gives you modeled  
emulations of many great amplifiers including: Vintage Vox™ AC-30 top boosts™, mid 70s’ Marshalls™ Master lead, Mesa Boogie™ Dual  
Rectifier stack and combos and Mark II stack and combo™, Matchless™ DC-30s and Fender™ Twins and Soldano™ SLOs. To call up any of  
these amplifier modelings, simply press any one of the 5 Amplifier model buttons on the front panel and the selected amplifier model is  
instantly called up.  
Johnson Amplifier Models: The Johnson Amplifier models offer amplifier tones that you never thought possible out of stock (un-modified)  
amplifiers. We at Johnson Amplification have basically taken the best of all amplifiers and performed the custom mods on them. This means  
that you can now have the custom Marshall™ with the higher gain stages, or that Soldano™ with more low end, and still remain ultra quiet.  
And, if having these custom amp modifications were not enough, the Johnson Amplifier custom modules give you the ability to combine two  
Amplifier paths on the right and the left at the same time to produce “mammoth” guitar tones when a morphing expression pedal is assigned.  
A-B channel switching: To give each modeled amplifier in the Millennium even more flexibility, we have included A-B channel switching in  
each of the amp models. This is a great function to use for adding distortion or boosting for solos. The A-B channel selector is conveniently  
located on the front panel of the Millennium and can be given expression pedal assignment for quick switching on the floor with the J-12 or  
J-3 foot controllers or via a MIDI device.  
Amplifier Model Types  
The following describes the Amplifier model selections when any one of the six amplifier model and channel buttons (shown below) are  
pressed. Successive presses of each button will take you through the menu of available amp types for each amplifier model.  
Amer Stk  
Amer Cmbo  
Johnson  
Channel  
Brit Stk  
A
B
Brit Cmbo  
American Stack: Dual Rectifier, Boogie MK II, Soldano SLO  
American Combo: ‘65 Blk Face Twin, Twin Reverb Brite, Matchless DC-30 -1, Matchless DC-30 -2, Boogie MK II Combo, Rectif Combo  
British Stack: Marshall Master 1, Marshall Master 2, Marshall JCM 800, Hot Rod Marshall MSTR  
British Combo: ‘63 AC 30 Top boost, ‘63 AC TBoost Dirty, AC 30 TB Cln/Drty, Marsh JCM 800 Cmbo  
Johnson: JohnsonCln/Dirty, JohnsonDrt/HiGain, JohnsonCln/HiGain, Fender/Soldano, Fender/HotMarshal, Fender/MatchDrt, Fender/Rectifier,  
Matchless/Soldano, Matchless/HotMarshall, Match/Rectifier, Vox/Marshall, Vox/Matchless, Vox/Rectifier, Overdrive, Fuzz, Heavy Sustain,  
Clean/Fuzz, Low Gain/Fuzz, High Gain/Fuzz  
Channel: Pressing this button will toggle between the 2 channels within every amplifier model.  
Fender™, Marshall™, Mesa Boogie™, Matchless™, Soldano™ and Vox™ are all registered trademarks and are in no way associated with  
Johnson Amplification.  
8
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 1 Introduction  
Digital Effects  
Not only is the MIllennium a great stand-alone guitar amplifier, but it also has a world class digital multi-effect section that includes almost  
every studio-quality effect imaginable.  
Effects include:  
• Reverbs (Natural & Spring)  
• Choruses  
• Tremolos  
• Rotary Speaker Simulation  
• Phasers  
• Flangers  
• Auto panners  
• Analog/Digital Delays  
• Whammy Effects  
• Chromatic Pitch Shifters  
• Intelligent Pitch Shifter  
• Detuners  
• Digital Compressor  
Real Time Parameter Modifiers: Modifiers are unique tools that can be used to dramatically alter your sound based on information  
from signal amplitude, the settings of a Low Frequency Oscillator (LFO) or MIDI continuous controller information.  
Every preset in the Millennium has a set of modifiers. Up to 16 Modifier links can be assigned to control parameters. There are 5 types of  
modifiers that can be linked to a parameter: Foot Switch, Expression Pedal, MIDI CCs, LFOs, and Dynamic (signal level dependent).  
MIDI CCs: When you use MIDI CCs, your Millennium responds to CC numbers 0-127 and CHP (channel pressure or aftertouch).  
For example, you can have a synth's modulation wheel (usually MIDI CC#1) control the input level of a reverb and chorus in one Preset,  
while the delay feedback may be controlled in another. For more information on MIDI CCs, please see pg. 56.  
LFOs: When you use LFOs, parameter values can be controlled automatically between a defined minimum and maximum setting at a user-  
definable rate. Your Millennium has two user definable LFOs in each preset that can use unique speeds and waveforms, and can be assigned to  
any parameter.  
For example, you can create an auto panner without using an auto panner module. Simply link an effect's output pan parameter to the LFO  
modifier and the LFO will move that parameter back and forth. This modifier can be a very useful weapon in the ongoing battle of new sound  
creation. For more information on LFOs, please see pg. 56.  
Dynamic Modifiers: When you use Dynamic Modifiers, the parameter values are controlled in relation to the dynamics of the input signal.  
The possibilities are nearly endless. For more information on Dynamic Modifiers, please see pg. 56.  
For example, you could link the Dynamic Modifier of a Preset to control a chorus level. It doesn't sound like much on paper, but imagine the  
expressiveness of this type of effect on a lead. As you play the guitar harder, the chorus becomes less apparent. Play softly and the chorus  
increases. ALL IN REAL TIME! For more information on dynamic modifiers, please see pg. 56.  
For more information on using modifiers see the “Assigning Modifiers” section. on page 56  
9
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 1 Introduction  
Basic Specifications  
2 Inputs, Up to 4 Extension Speaker Outputs and XLR Cabinet Emulation Outputs  
With the Millennium, the input section offers both a Bright and Normal input, and up to 4 extension speaker cabinets can be connected to the  
Millennium. The Bright and Normal Inputs give you the best of both worlds. Using the Bright Input produces a hotter and louder tone, where  
the Normal Input will produce a more natural coloring of the tone. The Millennium’s four extension speaker cabinet outputs give you the  
ability to drive up to 4 extension speaker cabinets with the Millennium, producing a wall of sound. And if that weren’t enough, the Millennium  
also offers separate XLR Cabinet Emulation outputs for recording or running direct.  
Programmable Mono FX Loop  
For those of you that feel the need to add additional effects to the already extensive menu of sounds, the Millennium provides a line level pro-  
grammable FX loop. The signal leaves the Millennium after the Wah section and returns just before the amplifier modeling paths.  
10  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 1 Introduction  
Foot Controller Compatibility  
Although the Millennium has incredible flexibility on its own, we at Johnson Amplification have made the Millennium compatible to use with  
the Johnson Amplification J-12 foot controller, or the Digitech Control One. The optional J-12 can help you maximize the potential of your  
Millennium. Since the J-12 “talks” to the Millennium using a proprietary communication protocol, it offers better response time and capabili-  
ties not available with conventional MIDI pedalboard controllers.  
The Johnson Amplification J-12 foot controller  
The Johnson Amplification J-12 foot controller offers continuous control in real time over all aspects of your tone when used in conjunction  
with the Millennium 250. The J -12 offers 12 heavy duty metal footswitches and two built-in expression pedals which can be assigned to  
control any parameter of the Millennium in a heavy duty steel chassis. For more on the J-12 foot controller, please see pg. 69.  
The J-3 foot switch  
The Johnson Amplification J -3 footswitch offers three footswitches that can be assigned to perform several different functions. Out of the box,  
the J -3 will change presets Up and Down and will A-B channel switch. Changing these footswitch functions is done on Pages 14 and 15 of the  
Utility menu. For more information on J-3 foot switch assignments, please see pg. 67.  
The Digitech Control One foot controller (Not Shown)  
The Digitech Control One foot controller offers 12 footswitches for preset and parameter control. It also features a built-in Expression pedal.  
The Control One also gives you the option of adding another expression control (via the external expression pedal jack which is located on  
the rear of the Control One foot controller).  
11  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 1 Introduction  
Module Types  
Each effect in the digital FX section is contained in separate effect blocks referred to as “Modules”. There are three basic types of FX Modules  
used by the Digital FX section of the Millennium  
• Mono FX module  
• Dual FX module  
• Stereo FX module  
The figure below illustrates how signals are routed through each type of FX module. Although all three modules are shown with stereo  
inputs, they can still be used with a mono source. The mono source would just be routed to both sides of the module’s inputs. Notice how  
the Dual FX module maintains a stereo image, while the mono FX module always sums the signal  
Mono FX Module  
Stereo FX Module  
Dual FX Module  
L
R
L
R
L
R
Effect  
Processing  
Effect  
Processing  
Effect  
Processing  
Module Sizes  
These modules vary in size ranging from 1/4 size to Full. In order to achieve the nearly endless combinations of effects and routings, we've  
supplied you with four different module sizes and they are as follows:  
• Full (module type = FUL)  
• 3/4 (module type = 3-4)  
• Half (module type = HLF)  
• Quarter (module type = 4th)  
Dividing the S-DISC II’s processing power allows your Millennium to produce up to 4 digital effects at one time. The figure below represents  
how the S-DISC II can be divided to accommodate a wide variety of effect routing.  
FULL  
3/4  
HALF  
QUARTER  
S-DISC II  
A Full module type offers effects with more flexibility and power than the Half modules, and so on, but all four sizes of FX modules feature  
high quality effects, so you don’t have to worry if you need to divide the S-DISC II pie four ways. For a complete list of these FX types please  
see the Editing modules section. For a complete list of effect configurations please see the Appendix section on page 85  
12  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Section-2 Setting Up  
Making Connections  
Your Millennium can be connected in several different ways to meet the requirements of specific applications. The following diagrams offer  
some different ways your Millennium can be connected.  
NOTE: In the following diagrams, we have shown use of the external FX loop.  
Input  
Output  
Loop Send  
Loop Return  
Input  
Left Speaker Output  
Right Speaker Output  
Millennium into Two 2X12 or 4X12 Extension Speaker Cabinets with Selectable Voicings  
The Millennium Two-Fifty offers selectable voicing modes for using either 2X12 or 4X12 extension cabinets located in the Utility menu. To  
select which voicing is to be used. From Program mode, press the <Utility> button and turn the <Data/Wheel> until you reach page 1. Now  
use the <3> knob to select either the 2X12 or 4X12 voice. Once the selection has been made, press the <Program> button to exit. You can  
now make connections from the left and right extension cabinet outputs (located on the rear of the Millennium). Use an un-shielded speaker  
cable and run into the input jacks of either 2X12 or 4X12 extension cabinets. Always make sure that the extension speaker cabinet being used  
has minimum input load resistance of 4 ohms.  
13  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Output  
Input  
Loop Return  
Loop Send  
Input  
Left Direct XLR Output  
Right Direct XLR Output  
4
6
4
6
6
4
4
6
6
4
4
6
6
4
4
6
6
4
4
6
6
4
4
6
4
6
2
2
8
8
2
2
8
8
2
2
8
8
2
2
8
8
2
2
8
8
2
2
8
8
2
2
8
8
2
2
8
8
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
0
0
10  
10  
Aux  
1
2
Aux  
1
2
Aux  
1
2
Aux  
1
2
Aux  
1
2
Aux  
1
2
Aux  
1
2
Aux  
1
2
4
6
4
6
4
6
Aux  
Aux  
Aux  
Aux  
Aux  
Aux  
Aux  
Aux  
0
0
0
0
0
0
0
0
-1  
+1  
-1  
+1  
-1  
+1  
-1  
+1  
-1  
+1  
-1  
+1  
-1  
+1  
-1  
+1  
-2  
+2  
-2  
+2  
-2  
+2  
-2  
+2  
-2  
+2  
-2  
+2  
-2  
+2  
-2  
+2  
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
-3  
-4  
+
3
+4  
+4  
+4  
+4  
+4  
+4  
+4  
+4  
-5  
+5  
-5  
+5  
-5  
+5  
-5  
+5  
-5  
+5  
-5  
+5  
-5  
+5  
-5  
+5  
Pan  
Pan  
Pan  
Pan  
Pan  
Pan  
Pan  
Pan  
Mute  
Mute  
Mute  
Mute  
Mute  
Mute  
Mute  
Mute  
L
/
R
L
/
R
L
/
R
L
/
R
L
/
R
L
/
R
L
/
R
L
/
R
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
+10  
+5  
0
-5  
-5  
-5  
-5  
-5  
-5  
-5  
-5  
-10  
-10  
-10  
-10  
-10  
-10  
-10  
-10  
-20  
-20  
-20  
-20  
-20  
-20  
-20  
-20  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
-∞  
-∞  
-∞  
-∞  
-∞  
-∞  
-∞  
-∞  
1
2
3
4
5
6
7
8
Running Direct and using the Programmable Cabinet Emulator XLR Direct Outs  
The Millennium offers you two ways to record guitar tracks. With the first, you can do classic recordings by placing a microphone in front of the  
speakers of the extension cabinet(s). Or, you can use the XLR direct output to record direct to a mixing console. When running direct, the  
speaker cabinets can be disconnected so the only signal being heard, is that being run to the board.  
Now you can run out of the Millennium to the mixing board using the following XLR cabinet functions:  
XLR Cabinet Emulation functions  
Engaging the XLR cabinet emulator is done in Page 2 of the Utilities menu. To get there, press the <Utilities> button. Now use the <Page>  
knob and turn to page 2. Once there, you can globally enable (global on) or disable (global off) the emulator or enable local settings (local on)  
by turning the <4> knob. Set up local (presets dependent) cabinet emulation is located on page 2 of the Output/Master mix module in edit  
mode  
To exit this mode, simply press the <Preset> button.  
At this point, you will want to run from either Left or Right XLR outputs (or both for a stereo mix), into the selected inputs of the mixer. You  
can set the Output mode to either Stereo (splitting the signal into a stereo soundfield) or Mono (summing the stereo signal) on page 1 of the  
Utilities menu by using the <2> knob to select the mode.  
As usual, it is a good idea to check all of the cables being used when making connections to ensure that good contact is being made.  
Notice that once the XLR speaker cabinet emulator is turned on, the SPEAKER icon will appear in the display.  
14  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Getting Around In the Operating System  
The menu structure of your Millennium has been specially designed to be easy to use. The display shows the information you need, but to  
make things even easier for you, illumination of the front panel buttons offers additional operating information.  
The front panel buttons give you information in one of two ways:  
1 - If the button is dim, its function is inactive. Pressing a dim button causes it to light brightly and its function becomes the active item in  
the display. If the dim button doesn’t light after you press it, the button is unavailable.  
2 - If the button is bright, its function is active.  
Preset Mode  
Preset mode allows you to scroll through the Factory and User presets using the <Preset/Effect> wheel. When your Millennium is turned on,  
it sets itself to Preset mode. Preset mode is active when the <Preset> button is lit and a preset name is present on the information line (top  
line) of the display.  
FX Edit Mode  
This mode allows you to edit:  
1. Digitally controlled Analog Wah  
2. FX loop  
3. Amp Models  
4. Noise Gate  
5. Selecting Effect Configurations  
6. FX Modules  
7. Output Mode of your Presets  
Use the <Edit> button to enter the FX Edit mode.  
A helpful hint: If you look at the Effect Routing matrix while you press the FX <Edit> button, the currently selected module will flash.  
Your Millennium uses “Pages” to navigate within an effect. A “Page” is a group of up to four effect parameters that appear on the screen at one  
time. Use the <Mix/Page> knob to move through the pages in the menu. Note that as you scroll through the pages, the page indicator in the  
lower left corner of the display changes to show the currently displayed page number.  
Utility Mode  
From the initial power-up of the unit, access to all of the menu pages of the utility mode can be made by simply pressing the <Utility>  
button located on the front panel of the unit. From this point, the display will tell you that you are in the utility mode and you can scroll  
through the options by turning the <Mix/Page> knob.  
Assign Mode  
Once the Millennium is in assign mode, all modifier assignments can be made. This assign mode gives you the ability to assign LFOs, dynamic  
modifiers, foot switches and expression pedals to almost any parameter in the Millennium. Access to this function is located on the front panel  
or in the utilities pages within the Millennium. For more information on assignments, please see pg.56.  
15  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Getting Sounds  
It never fails, there always seems to be a sound man at the back of the room, or an engineer in the control room that wants “more of this, or  
less of that” (bottom line: your ear is king). But, to accommodate these situations, you may need to make some minor adjusting here and there  
along the way. So here are some helpful guidelines for getting great sounds, while keeping everyone happy.  
Input and Master Output Adjustments  
The best setting for the input control is to use the <Input level> knob so you are occasionally lighting the clip LED. As far as setting the  
Master output level, let your ears be the judge. But, if you can’t hear the rest of the band, chances are that you need to back off on the Master  
volume level of the Millennium.  
Amplifier settings  
Gain Adjustments  
To adjust the gain in the Amplifier modeling section, either turn the <Gain> knob on the front panel or press the <Edit> button to put  
you in edit mode. Now use the <Preset/Effect> wheel to scroll to the amplifier model. From this point, turn the <Mix/Page> knob to  
move to Page 2 of the amplifier module. The number of different amp tones are almost unlimited when making gain adjustments. Your gain  
settings range from 0.0 to 10, so this gives you plenty of room for great tones in between. Note that the gain parameter will add distortion  
gain when a distorted amplifier module is used and will add volume when a clean tone amplifier model is used. Always remember to save  
any changes.  
EQ and Preset Level  
Adjusting the EQ is as easy as grabbing the knob and turning. The <Treble> controls the level of the High frequencies. The <Mid> knob  
controls the level of the mid range frequencies, and the <Bass> knob controls the bass frequencies. In Preset mode, the level of each  
frequency band is displayed in the 7 segment displays located above each knob. EQ settings range from 0.0 to 10. The Millennium also gives  
you the ability to adjust individual preset levels by simply turning the <Level> knob to the desired setting. Always remember to save any  
changes.  
Note: Changes to the Gain, EQ and Level settings can be done using either the tone controls (located on the left side of the front panel) or the  
<1,2,3 and 4> knobs located directly below the display. Using either editing method will correspond in the display. A sample setting is shown  
below with Channel B being the active channel.  
Level  
Gain  
Bass  
Mid  
Treble  
This example setting has been set from Preset mode using Channel B. Once the Millennium is in Edit mode the display will correspond.  
16  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
•When the tone controls are used, the display will appear as follows on page 2 of the amplifier module when the Millennium is in Edit  
mode:  
a:gain lvl B:GAIN LVL  
1
2
3
4
.40  
.50  
.70  
70  
.
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
#
DIGITAL  
BANK  
PAGE  
b
2
OF  
5
•Using the <Page> knob turn to page 4 and the display will appear like this:  
CHN B:TREB MID BASS  
4
2
3
2.5  
25  
.
25  
.
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
#
DIGITAL  
BANK  
PAGE  
b
4
OF  
5
Amplifier Model and Channel Selection  
Selecting amplifier types in the Millennium is as easy as pushing a button. To call up any one of the amplifier model types, simply press one  
of the six buttons in the <Amplifier Modeling> button array (subsequent presses of any amplifier model button will move you to the  
next amplifier model available), or turn the <2> when the Millennium is in edit mode on page 1 of the Amplifier module. A-B channel  
switching can be achieved within the Amp model by pressing the <Channel> button, or turning the <4> button while the Millennium is  
on page 1 of the Amplifier module in edit mode. Always remember to save any changes.  
Amplifier Contour Control  
Using the <Contour> knob will give you the ability to control the tonal qualities of the power amp section of the Millennium. When the  
<Contour> knob is turned all of the way down, the power amp tone is flat. Turning up the knob brightens up the signal in the power amp  
section.  
Digital Effects  
Wet/Dry Mix Adjustments Global or Local  
To change the mix of dry and wet signal of the overall effect level, use the <Mix/Page> knob. Mix settings range from 0 (all dry) to 100%  
(all wet) when the Millennium Wet/Dry mix is set to Local or Global. When the Wet/Dry mix is set to Global (setting the Wet/Dry mix  
either Local or Global is done on page 2 of the Utility menu), the mix control effects the percentage of Wet/Dry mix in every preset. As the  
acoustics of any room change, you can easily adjust the mix of your effects accordingly with the turn of a knob. The master mix of each  
preset can be modified in the Master mix menu while in edit mode by pressing the <Edit> button then scrolling through the preset pages  
until the L/R Out and speaker icons blink.  
17  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Digital FX Quick Adjust Knobs  
Many digital effects available in the Millennium have a simple quick adjustment knob located on the front panel. These knobs are great to  
use when you need to bring in or bring down the level of a selected effect. To use these knobs when the Millennium is in Preset mode,  
simply turn the appropriate quick adjust knob and adjust. Always remember to store the settings once they are dialed-in.  
The following list gives a brief explanation of each FX level control knob.  
Speed: The <Speed> knob controls the speed of the first modulation effect in the configuration when a modulation type effect, such as a  
Tremolo is used in the selected preset. The range for the speed is from 0.06 to 16.0 Hz.  
Depth: The <Depth> knob controls the depth of the first modulation effect in the configuration when a modulation type effect, such as a  
Tremolo is used in the selected preset. The range for the depth is from 0 to 100%.  
Delay: The <Delay> knob controls the delay level of the first delay in a configuration, when a Delay module is used in the selected preset.  
The range of the delay level is from Off to 100%.  
Reverb: The <Reverb> knob controls the reverb level of the first Reverb module in the configuration, when a Reverb module is used in a  
selected preset. The range of the reverb level is from Off to 100%.  
18  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Selecting A Preset  
When you first turn on your Millennium, you are in Preset mode, and the display will appear something like:  
ꢀ
ꢀ
Clean Comp Delay  
msdB 3  
%
0%kHz  
msdB  
0%kHz  
0%kHz 100  
1
2
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
#
b
CLIP  
PAGE  
OF11  
To select a preset, do the following:  
1. Make sure Preset mode is selected (the <Preset> button will be brightly lit). If the <Preset> button is dim, press it once to return to  
preset mode.  
2. Use the <Preset> button to select the preset bank (factory or user). Successive presses of the <Preset> button toggle between the  
factory and user bank of presets.  
3. Using the <Preset/Effect> wheel, scroll to the preset you want to use.  
Using the Tuner  
The Tuner of the Millennium can be accessed two ways. Either in page l of the Utility menu or by using the optional Johnson Amplification  
J-12 foot controller. The following explains both modes of operation.  
Utility Menu Tuner Mode  
1. Press the <Utility> button once. The display reads:  
Stereo Cab:4x12 Tuner  
1
%kHz  
msdB  
2
3
4
ꢀ
2
2
Off  
LINK CHANGED  
LINK CHANGED  
GATE  
LINK CHANGED  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
2
127  
FACTORY  
USER  
MIDI  
DIGITAL  
CLIP  
SOLO  
PAGE  
BANK1  
OF16  
L/R OUTS  
2. Now turn the <4> knob to turn the tuner on. The display will now appear something like this:  
127 ?? TUNER A=440 Output  
%kHz  
msdB  
%
ꢀ
3
4
100  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
DIST  
EQ  
FACTORY  
USER  
MIDI  
#
DIGITAL  
SOLO  
b
CLIP  
L/R OUTS  
19  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 2 Setting Up  
Instant Tuner Access  
To instantly access the Tuner mode of the Millennium, press and hold the <Utility> button. This will take you directly to the tuner  
function.  
3. As you play a note on the guitar, the large number display will tell you which note you are playing, while the meter will show you if the note  
is flat or sharp. If the meter is moving to the right, the note you are playing is sharp. If the meter moves left, the note is flat. The goal is to  
tune your guitar so that the meter stops moving, and the display will lock-in, indicating that you are in tune. Once you start playing the  
selected note, the display will read as follows:  
A Tuner A=440 Output  
%kHz  
%
888msdB 888%kHz  
msdB  
1
3
4
100  
LINK CHANGED  
ꢀ
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
A
127  
FACTORY  
BANK  
FX LOOP  
USER  
MIDI  
DIGITAL  
CLIP  
SOLO  
#
b
L/R OUTS  
PAGE  
19  
OF18  
4. Press the any button to exit the Tuner mode.  
Reference and Output  
The Millennium gives you the option of changing the Tuning reference from as low as F# or A=427 to A=453, by simply turning the <3>  
knob while the Millennium is in Tuner mode. Another feature available in the Millennium Tuner mode, is the ability to set the amount of signal  
that is passed to the output while tuning. This has a range from 0 (mute) to 100%. The output can be changed by turning the <4> knob to the  
desired level while the Millennium is in Tuner mode.  
Johnson Amplification J-12 Tuner Mode  
To access the Tuner mode using the optional J-12 foot controller, press and hold the <Bank Up/Tuner> footswitch to engage tuner mode.  
1. As you play a note on the guitar, the indicator in the display of the J-12 will move either to the right, or the left. If the indicator is moving  
right, the note you are playing is sharp. If the indicator moves left, you are flat. The goal is to tune your guitar so that the indicator stops  
in the middle and the display locks-in, indicating you are in tune.  
2. In both methods of tuning, the tuner is referenced to A=440Hz. If you prefer tuning sharp or flat according to the A reference, use the  
<3> knob to select a new reference. This can be set as high as A=453Hz or as low as A=427Hz. The tuner can also be used for alternate  
tuning references where A=Ab (meaning you play an A note, but you hear an Ab note). It is possible to tune as low as A=Gb.  
3. At this point, press any footswitch on the J-12 to exit the Tuner mode.  
20  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
Section-3 Editing Presets  
Naming and Storing Presets  
Before we get into editing presets and creating your own, let’s learn how to store changes so you won’t lose any modifications that you will  
want to keep. The Store procedure allows you to re-name, relocate and save any modifications you have made to presets so that they can be  
accessed easily later.  
Naming the Preset  
1. Press the <Store> button once. The display shows the current preset name (which may look something like this):  
Name: Clean Comp Delay  
%kHz  
InS  
%kHz  
CAꢀ%kHz nbr  
1
PmsdB 2  
3
msdB 4  
COpmsdB  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
A cursor appears under the first character of the preset name.  
2. Using the <Preset/Effect> wheel, change the character to the one you want in the selected position.  
3. When the correct character is displayed in that position, use the <Page> knob to scroll the cursor to the next character you want to  
change.  
4. Use the <1> knob to change the letter’s case. The <2> knob is used to select numbers, The <3> knob is used to insert spaces. The  
<4> knob is used to copy and paste characters.  
5. To copy a character, position the cursor under the character you want to copy (using the <Page> knob), then turn the <4> knob  
clockwise. To paste the copied character, position the cursor where you want to paste the character, then turn the <4> knob counter-  
clockwise.  
6. To abort the procedure, press any button.  
21  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
Storing the Preset  
1. When you have the name as you want it to appear, press the <Store> button again. The top line of the display appears something like  
this:  
Store Pst to: Matchless  
2
3
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
This screen allows you to select the location of the new Preset. Note that when the preset is stored, it is stored in the User bank of presets  
because factory presets cannot be overwritten.  
2. Use the <2> knob or the <Preset/Effect> wheel to select the preset number where you want to store the new preset.  
3. Press the <Store> button again. The top line of the display briefly reads:  
Storing Preset  
2
3
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
after which you are taken to the preset you have just stored.  
The newly created preset is now loaded, and can now be recalled at any time.  
4. To abort the procedure, push either the <Preset> button to take you to Preset mode, the <Edit> button to take you to FX Edit mode, or  
the <Utilities> button to take you to Utility mode, depending upon which mode you want to enter.  
22  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
Editing a Preset  
The Millennium is capable of producing almost any sound ever thought conceivable. Whether it be amplifier tone or an effect configuration  
that utilizes the most sophisticated digital effects available. Great sounds aren’t just an unrealistic concept, but a very achievable possibility. In  
the next few pages, we will give you some pointers in editing presets to help achieve your own unique tones.  
Preset Editing Sections  
1. Integrated Amplifier Model Editing  
2. Digitally controlled Analog Wah Editing  
3. Noise Reduction Editing  
4. Digital Effects Editing  
Integrated Amplifier Model Editing  
From any preset within the Millennium you can select and edit any amplifier model by performing the following procedures:  
Integrated Amplifier Model Selection  
To call up any Integrated Amplifier Model in the Millennium while in preset Mode, all you have to do is press any one of the Amplifier model  
buttons and the selected amplifier model type is called up. Successive presses of the selected amplifier model button will call up any other  
amplifier type within that model. The illustration below shows the selection of the British Combo Amplifier Integrated Model:  
Johnson  
Channel  
Amer Stk  
Amer Cmbo  
Brit Stk  
A
B
Brit Cmbo  
Editing Integrated Amplifier Models  
1. From Preset mode press the <Edit> button once and the display will appear something like this:  
Wah Pedal  
2
Toe Heavy  
4
1
byp  
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
23  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
2. Now use the <Preset/Effect> wheel and scroll to the Amplifier type module. Once you are there, the display will appear something like  
this:  
'65 Blk Face Twin Chan  
2
4
AC1  
b
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
5
3. Using the <2> knob will allow you to select any one of the amplifier models within the Millennium and the <4> knob will select either  
the A or B channel. This will make the selected channel active for editing  
4. Once the amplifier model and channel have been selected, use the <Page> knob to move to page 2 of the amplifier model edit menu.  
Page 2 lets you adjust the gain and preset levels of channel A or B. The active channel (A or B) appears in upper case letters and will  
appear something like this :  
a:gain lvl B:GAIN LVL  
1
2%  
100  
93%  
2
3
4
40  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
2
OF  
5
Note: To toggle between the active A or B channel, simply press the <Channel> button. This is essential for editing because when the A or  
B channel is active you can make all EQ, gain and preset level modifications using either the <1>, <2>, <3> and <4> buttons, or  
you can use the <Gain>, <EQ>, or <Level> knobs to make any adjustments.  
5. Once the adjustments are made to the gain and levels of amplifier models and channels, use the <Page> knob and turn to page 3  
(Channel A) and 4 (Channel B) of the amplifier model editing section to make any EQ adjustments. The display will appear like this:  
chn a: treb mid bass  
2
3
4
5.4 5.4 5.4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
3
OF  
5
24  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
6. Now use the <Page> knob to move to page 5 of the amplifier model editing section and the display will appear like this:  
A:DIG LVL b:dig lvl  
1
%
%
2
3
4
100  
100  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
5
OF  
5
7. Using the <1> knob will let you adjust the digital level of Channel A. The <3> knob adjusts the digital level of Channel B.  
Note: Digital Level sets the amount of digital effect level that is heard within the selected preset.  
Always note that the channel (A or B) that appears in upper case letters is the currently active channel and can be toggled any time using  
the <Channel> button to select either channel  
8. Once all of the modifications have been made to the Amplifier model in the currently selected preset, press the <Store> button to save  
your changes. To exit the amplifier model editing section, press the <Preset> button.  
Analog Wah Editing  
Analog Wah editing can be done by performing the following procedures:  
1. From Preset mode press the <Edit> button and the display will appear like this:  
Wah Pedal  
1
Toe Heavy  
4
2
byp  
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
2. Using the <1> knob will either turn the Wah On or Off. The <2> is used to activate the Wah pedal range and the <4> knob is used to  
select the Wah type.  
25  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
3. The <2> button (pedal parameter) can be assigned to a footswitch to bypass or turn the module On. This parameter can be selected by  
turning the <2> knob and a  
icon will appear directly beneath the parameter. At this point press the <Assign> button and  
Changed  
the display will appear as follows:  
Avail Link for: Pedal  
1
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER9 b  
DIGITAL  
#
BANK  
PAGE  
1
OF  
4. Now press the footswitch to be assigned. You can use either a standard volume or voltage controlled Expression pedal connected  
to the Expression pedal I and 2 pedal inserts on the rear panel of the Millennium or you can use either one of the Expression  
pedals on the optional J-12 Foot Controller to act as the Wah pedal. If the selected footswitch is already assigned to control another  
parameter, the display of the Millennium will ask you if you want to re-assign. If you wish to re-assign, turn the <1> knob for yes or the  
<2> knob to abort the assign function.  
Note: Any time an assignment to turn a parameter On/Off is made you must decide if you want the parameter On when you enter the  
selected preset. If you want it on, make the assignment to the parameter when the parameter is set to On. Otherwise, have the  
parameter set to Off or Bypass and the parameter will not be active within the Preset until the footswitch is used to activate the  
parameter  
5. To Exit the Analog Wah edit mode, simply press the <Preset> button.  
Noise Gate Editing  
The procedure for editing the Noise Gate module within the Integrated amplifier section is as follows:  
1. From Preset mode, press the <Edit> button and turn the <Preset/Effect> wheel until the display appears something like this:  
Noise Gate S1Pre Gate  
1
2
4
On  
F 1  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
3
2. At this point, you can use the <1> knob to turn the Noise gate On or Off and the <4> knob is used to select the Noise gate default.  
3. Now use the <Page> knob and turn to page 2 of the Noise Reduction module. Turning the <1> knob lets you select the Noise gate type  
and its position in the signal flow.  
26  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
4. Once the Noise gate type and position are selected use the <Page> knob and turn to page 3 of the Noise gate edit module. This page is  
used to set the Threshold, Attenuation, Attack and Release parameters. Higher Threshold settings will close the gate sooner. Lower Release  
settings allow the gate to open up faster  
5. To exit Noise gate edit mode, press the <Preset> button.  
Selecting Effect Configuration Routes  
Within every preset of the Millennium, you have the option of selecting any 1 of the 15 Effect Configuration routes available in the Millennium.  
This can be very helpful when you have a preset that uses an Amplifier model that you prefer, but the currently selected effect configuration is  
not ideal for the digital effects that you wish to use in the preset. You can easily change these Effect configurations by using the following  
procedure as a guide:  
1. Accessing the effect configurations can be done one of two ways. From Preset mode, simply press the <Config> button, or press the  
<Edit> button and use the <Preset/Effect> and turn until the display appears something like this:  
Config: Series 4,4,4,4  
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
2
Note that the effect configuration is flashing  
2. Now use the <1> knob to select any one of the 15 different configurations available.  
3. Once the configuration has been selected, press the <Store> button to save any changes.  
4. To Exit the configuration menu, just press the <Preset> button to return to preset mode.  
A complete listing of the effect configurations of the MIllennium can be found on page 85.  
FX Edit Mode  
1. From Preset mode, press the <Edit> button. The display appears something like this:  
Wah Pedal  
1
Toe Heavy  
4
2
byp  
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
1
OF  
1
27  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
When you enter FX Edit mode, the first page of every FX Module allows you to:  
1) Bypass that effect module (by turning it on or off) using the <1> knob.  
2) Select an Effect Module (Only in the Digital Effect section), using the <2> knob.  
3) Store the Default using the <3> knob (for more info on storing Defaults, see pg. 30.  
4) Select a Default for the selected Effect Module using the <4> knob.  
Changing Effect Modules  
Each preset can be comprised of up to 4 digital effects (in addition to the Amplifier section). You can scroll through the modules in each preset  
two different ways:  
1. By pressing the <Edit> button to enter FX Edit mode and using the <Preset/Effect> wheel to scroll through the different modules, or  
2. By using the FX Library buttons. Pressing the <Edit> button takes you directly to the first module in the Amplifier section. Likewise,  
pushing the <Other> button takes you directly to the first module in the digital FX section and displays which effect is in it. Subsequent  
presses of the button scrolls you through subsequent modules that are in the effect configuration.  
Once you reach a module you want to change (ie: you want to swap a delay for a reverb), use the <2> knob to select a new effect.  
Selecting a Default  
Once you have selected the effect you want in the preset (ie: Dual Chorus), you can quickly scroll through several different Dual Chorus  
defaults stored in your Millennium's library. Defaults are modified effect modules which have custom settings that can be called up to use in a  
preset anytime that particular sound is required.  
Example:  
There are 10 Dual Chorus defaults to choose from. Some Factory presets use these default settings. So, if you like the Dual Chorus that is  
being used in Factory preset #45, and would like to use it in preset #98, simply scroll to the modulation module, then use the <4> knob to  
recall the default (which happens to be F4-MediumWell) in preset #45. This eliminates the need to copy all those parameters from one  
location to the other.  
For a complete list of all the FX Modules and their Defaults, see page 34.  
Adjusting the Module’s Parameters  
Once in Edit mode, the parameters of every default module can be accessed through a series of pages. You adjust the level of a particular  
module from Edit page 2. If you’re not already in Edit Mode, press the <Edit> button. You can then use the <Preset/Effect> wheel to scroll  
to the module you want to change (ie: Dual Chorus). Now use the <Page> knob, scroll to page 2. You can now change the individual  
module’s level using the <1> knob. Settings range from 0 (off) to 100%.  
Custom Defaults  
Once you have tweaked the parameters of an effect module, you can store it off as part of the preset. Once it is stored off, it becomes a custom  
default for that preset, but is not added to the User default library. To save the settings as User Defaults, please see pg. 31  
28  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 3 Editing Presets  
Comparing Changes  
During the course of editing presets, you may find that you want to compare the edited version of the preset to the original, stored version.  
Fortunately, your Millennium provides you with a Compare function.  
To compare an edited preset with the original stored version, please do the following:  
1. While in FX edit mode, press the <Edit> button once. The top line of the will read:  
*Comparing Original Pst*  
%kHz  
msdB  
%kHz  
msdB  
%kHz  
%kHz  
msdB 4  
msdB  
LINK CHANGED  
1
2
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK  
EQ  
GATE  
L/R OUTS  
2
FACTORY  
BANK  
USER  
DIGITAL  
CLIP  
#
b
L/R OUTS  
PAGE  
1
OF  
2
When this message is displayed, the originally stored preset is temporarily loaded and active.  
2. To return to the edited version, press the <Edit> button to get back to FX Edit Mode.  
29  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Section-4 Editing Modules  
Storing/Naming Defaults  
Before we get into editing modules and creating your defaults, let’s learn how to store changes so you won’t lose any modifications that you  
will want to keep. The Store procedure allows you to re-name, relocate and save any modifications you have made to defaults so that they can  
be accessed easily later.  
1. When you have satisfactorily altered an effect default (or created a new one), scroll back to Page 1 of the effect module you are editing (if  
you’re not already there). The display appears something like this:  
Fx:Dual Cho  
1
Custom  
%kHz  
msdB  
%kHz  
HLF  
%kHz  
%kHz  
msdB  
2
msdB 3  
msdB 4  
Sto -ꢀ--  
LINK CHANGED  
On  
LINK CHANGED  
LINK CHANGED  
LINK  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
45  
USER  
FACTORY  
DIGITAL  
CLIP  
#
BANK  
PAGE  
b
L/R OUTS  
1
OF  
5
2. From page 1 of the FX Edit menu, turn the <3> knob clockwise. You will then be able to name your new default.  
Naming the Default  
1. Using the <Preset/Effect> wheel, change the character to the one you want in the selected position.  
2. When the correct character is displayed in that position, use the <Page> knob to scroll the cursor to the next character you want to  
change.  
3. Use the <1> to change the letter’s case. Use the <2> knob to select numbers. The <3> knob is used to insert spaces. The <4> knob is  
used to copy and paste characters.  
4. To copy a character, position the cursor under the character you want to copy (using the <Page> knob), then turn the <4> knob  
clockwise. To paste the copied character, position the cursor where you want to paste the character, then turn the <4> knob counter-  
clockwise.  
5. To abort the procedure, push either the <Preset> button to take you to preset mode, the <Edit> button to take you to FX Edit mode, or  
the <Utility> button to take you to Utility mode, depending upon which mode you want to enter.  
30  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Storing the Default  
1. When you have the name as you want it to read, press the <Store> button. The top line of the display reads:  
Store To: [Name]  
This screen allows you to select the location of the new default. Note that when the default is stored, it is stored in the User bank of defaults  
because factory defaults cannot be overwritten.  
2. Use the <2> knob to select the default number where you want to store the new default.  
3. Press the <Store> button again. The default is saved off and you are taken to page 1 of the FX edit menu.  
The newly created default is now loaded, and can now be recalled at any time.  
4. To abort the procedure, push either the <Preset> button to take you to Preset mode, the <Edit> button to take you to FX edit mode,  
or the <Utility> button to take you into Utility mode, depending upon which mode you want to enter.  
Editing a Module  
Each of the Millennium’s effects has several usable factory defaults, however, you may want to tweak the parameters of the module in order to  
get the right sound you’re looking for. The parameters of each effect module are reached through a series of pages.  
1. Press the <Edit> button. The display looks something like this:  
Wah Pedal  
1
Toe Heavy  
%kHz  
%kHz  
msdB  
%kHz  
msdB  
2
msdB 4  
byp  
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK  
LINK  
EQ  
GATE  
L/R OUTS  
2
FACTORY  
BANK  
USER  
DIGITAL  
CLIP  
#
b
PAGE  
1
OF  
1
When you first enter FX edit mode (by pressing the <Edit> button), you are taken to the Analog Wah section. Turn the <Preset/Effect>  
wheel to scroll through the modules until you reach a digital effect module. Notice that as you scroll through the different modules, the  
currently selected module will flash in the Effect routing matrix of the display. Once you have reached a module in the digital effects section  
that you want to edit, use the <Page> knob to scroll to the particular parameters.  
Notice: Anytime a change is made to either an effect module or default, the Changed icon will appear directly below the effected  
parameter within the module or default and the <Store> button will light.  
31  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Scrolling through a Module’s Pages  
Notice in the bottom left corner of the display (just under the preset number) the display indicates which page you  
are on and the total number of pages within the module. Each page allows you to access up to four parameters using the <1> - <4> knobs.  
Example:  
To scroll through the parameter pages of the Dual Chorus module, from the Preset mode either press the <Mod> button on the front panel  
until the Dual Chorus module comes up in the display. or, press the <Edit> button and once this button is lit, use the <Preset/Effect>  
wheel to scroll to the Dual Chorus module. At this point use the <Page> button to scroll through the parameters of the Dual Chorus  
module.  
For a complete description of all the FX Modules and their parameters, see pages 35-55.  
Output Module Functions  
The last module in the audio chain within any preset of the Millennium gives you control over crucial output functions of the amplifier such as:  
Master mix, Master volume and On and Bypass of the XLR cabinet emulator for each preset.  
1. To access the Output module, press the <Edit> button and turn the <Preset/Effect> wheel counter-clockwise until the display appears  
like this:  
Master Vol XLR Cab Emul  
3
%
1
100  
byp  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
2
OF  
2
2. Using the <3> and <4> knobs will let you set the Master dry and wet levels in the selected preset.  
3. By turning the <Page> knob, you will now be taken to page 2 of the Output module and the display will appear like this:  
Master Vol XLR Cab Emul  
1
%
3
100  
byp  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
USER  
DIGITAL  
#
BANK  
PAGE  
b
2
OF  
2
4. The <1> knob is used to set the Master Volume level and the <3> knob is used to set the XLR Cabinet emulator to On or Bypass in the  
currently selected preset. To Exit the Output module, either turn the <Preset/Effect> wheel, or press the <Preset> button.  
32  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Digital Effect Module Size and Type  
With all of the work that these digital effect modules do for your sound, they have a tendency to work up an appetite. So, they consume their  
food from the FX pies chart referred to on page 12.  
Since some of these effect modules have a larger appetite than the others, they require more processing power. To help divide effect sizes, we  
have provided you with a chart below that tells you what size of effect block that each will fit in. This helpful chart will also let you know if the  
selected module is either a Mono, Stereo, or Dual type effect module.  
Note: The Effect Module size will always be displayed in Page 1 of the selected effect module next to the number 2 icon located in the  
display.  
Effect Name  
Effect Name  
Chorus/Dly  
Flange/Dly  
Dual  
Dual  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
✓
Dual Cho  
Quad Cho  
Octal Cho  
Dual Fla  
Dual  
Dual  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
✓
✓
✓
Dual  
Dual  
✓ ✓  
Pre Delay  
Reverb  
DualReverb  
St Reverb  
Gated Rvrb  
St Dual Reverb  
Room Echo  
Spring Tank  
Auto Wah  
Compressor  
GEQ8  
GEQ15  
GEQ31  
✓
Dual  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
✓
Dual  
✓ ✓ ✓  
✓ ✓ ✓  
✓ ✓  
Dual  
Dual Pha  
RotarySpkr  
St Tremolo  
Auto Pan  
Dual Dtn  
Quad Dtn  
Octal Dtn  
Smooth Pch  
Dual Pitch  
Quad Pitch  
Octal Pch  
St Pitch  
Dual  
Stereo  
Stereo  
Stereo  
Dual  
Stereo  
Dual  
✓ ✓ ✓  
✓  
✓
Stereo  
Stereo  
Dual  
✓
✓  
Dual  
✓
Dual  
Stereo  
Stereo  
Mono  
Mono  
Mono  
Stereo  
Stereo  
Mono  
✓ ✓ ✓ ✓  
Stereo  
Dual  
✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
✓
✓ ✓ ✓  
✓ ✓ ✓  
✓ ✓  
Dual  
Dual  
✓
Stereo  
Stereo  
Stereo  
Stereo  
Dual  
✓ ✓ ✓  
✓ ✓ ✓  
✓ ✓  
✓
✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
St GEQ8  
St PEQ3  
PEQ6  
St PEQ6  
Thru Module  
StDual Pch  
Whammy  
Harmony  
Delay  
✓ ✓  
✓ ✓  
✓ ✓ ✓  
✓ ✓  
✓ ✓ ✓  
✓
✓ ✓ ✓ Stereo  
✓
✓
St/Mono  
✓
✓ ✓ ✓ ✓  
Dual  
Dual  
Dual Delay  
Quad Delay  
Stereo Delay  
StDual Dly  
StQuad Dly  
Long Dly  
✓
Stereo  
Stereo  
Stereo  
Dual  
✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓ ✓  
✓ ✓ ✓  
Analog Dly  
StAlog Dly  
Stereo  
Stereo  
33  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Default List  
The Following list contains the names of all of the Effect Defaults in the Millennium  
Auto Wah  
•Low Sens  
•High Sens  
•Nasally  
Gated Reverb  
•100msGated  
•200msDcyEx  
•200msDecay  
•200msGated  
•300msDcyEx  
•300msGated  
•SmphnyHall  
•RichChamber  
•Sanctuary  
Quad Delay  
•RoundNRnd  
•SynchroTap  
•RtoLPanTap  
•TripleSlow  
•Ping Pong  
•400ms Thick  
•On the Rise  
•Shav&Hrcut  
•Horse Trot  
Multi-FX Mods  
Chorus/Delay  
•MedCHoEcho  
•LitChoEcho  
•MedChoSlap  
•DeepChoDly  
•ShimryEcho  
•ModDly300ms  
•DeepModDly  
Noise Gate  
•S1 Pre Gate  
•S2 Post NR  
•Post Tub  
•S2 PostDst  
•Fast Swell  
Quad Pitch  
•MajChord  
•MinChord  
•Oct/Dtn  
•5th/OctDtn  
•5Octaves  
Octal Pitch  
•Chord/Det1  
•MinChord2  
•Oct/Dtn  
•5th/OctDtn  
•5thsOcts  
•Gonzo  
•IntenseL  
•Intense R  
•FlaChorus1  
•FlaChorus2  
Compressor  
•Light  
•Medium  
•Slow Swell  
Dual Phaser  
•ShallowSlo  
•ShallowFst  
•MIld Slow  
•MIld Fast  
•Medium  
•Deep  
•Shimmery  
•PhaChorus1  
•Phas Chorus2  
•Psychelic  
•Heavy  
Choruses  
Dual Chorus  
•Medium  
Equalizers  
Flange/Delay  
•FlatLitD300  
•FlatMedD300  
•HeavyFlDly  
•LoSweepDly  
•ThroatyDly  
•DoublGonzo  
•Flangbelly  
•SaltPalace  
•CmntGarage  
8-Band Mono GEQ  
•Flat  
Stereo Delay  
•700ms/20%  
•Combfilter  
•Doubling  
•SlapRight  
•400ms/50%  
•500ms/30%  
•600ms/15%  
•MaxRepeats  
•350ms/0%  
•700ms/0%  
•Shallow  
•Low Pump  
•Sizzle  
•InvrtPhase  
•Smiley  
Spring Tank Reverb  
•Short Decay  
•Long Decay  
•Wet Spring  
•SurfSplash  
•Ratl&Boing  
•MildNWide  
•MediumWell  
•DeepDepth  
•Deep  
•Max Depth  
•Shimmery  
•SloVibrato  
•FstVibrato  
Stereo Pitch  
•5th Up  
•Min3rdUp  
•Maj3rdUp  
•OctaveUp  
•4thDown  
•Octave Down  
•2 OctsDown  
•InvrtPhase  
15-Band Mono GEQ  
•Flat  
•Low Pump  
•Sizzle  
•Smiley  
•InvrtPhase  
Reverbs  
Room Echo  
•WideSlap  
•LiveSlap  
•Springy  
•Stage  
•Voxy  
•Drum 1  
•Drum 2  
Detuners  
Reverb  
Dual Detuner  
•-5 Cents  
•SmoothHall  
•Bar'nGrill  
•OakFloorRm  
•Vocal Reverb  
•FoilPlate  
Stereo Dual Pitch  
•5th/OctUp  
•Min3rdUp  
•3rd/5th Up  
•Min 3rd/5th Up  
•4th/OctDn  
•OctUp/Down  
•OctDownDtn  
•1&2OctsUp  
Quad Chorus  
•Medium  
•MildNWide  
•Medium Well  
•Thick  
•-12 Cents  
Stereo Dual Delay  
•Skip  
•+/-5 Cents  
•+/-10 Cents  
•Single Vox  
31- Band Mono GEQ  
•Flat  
•Low Pump  
•Sizzle  
•Smiley  
•SwingPong  
•PingPong1  
•PingPong2  
•DoubleSlap  
•RoundNRnd  
•Hard2Tap  
•GoldPlate  
•DeepDepth  
•Deep  
Quad Detuner  
•Shallow  
•Medium  
•Wide  
•Smphny Hall  
•RichChmber  
•Sanctuary  
•Salt Palace  
•CmntGarage  
•PlutoVerb  
Other Modules  
•Max Depth  
•Shimmery  
•SloVibrato  
•FstVibrato  
•ChorusLeft  
Pre Delay  
•0ms  
8-Band Stereo GEQ  
•Flat  
•Low Pump  
•Sizzle  
•Smiley  
•InvrtPhase  
Harmony  
•Cmaj3rdUp  
•Cmaj6thUp  
•Emin3rdUp  
•Cmaj6thDn  
•Cmaj3rdDn  
•Emix3rdUp  
•Cmaj5thUp  
•1&2OctsUp  
•Deep  
•ThickEcho  
•30ms  
•60ms  
•90ms  
•120ms  
Octal Detuner  
•Shallow  
•Medium  
•Wide  
Stereo Quad Delay  
•RoundNRnd  
•SynchroTap  
•Ping Pong  
•400msThick  
•HorseTrot  
•Shav&Hrcut  
•Ratatat  
•Random  
Dual Reverb  
•BrightHall  
•LngDrkHall  
•ConcrtHall  
•MiniHall  
•FlatChambr  
•WarmChambr  
•Smphny Hall  
•BigCathedrl  
•SmlCatherl  
•GoldPlate  
•Thinplate  
•VocalPlate  
•PercPlate  
•StudiAmb  
•StudioRoom  
•WoodRoom  
•FlutterRvb  
•Very thin  
•CementRoom  
•HugeArena  
Octal Chorus  
•Medium  
•Shallow  
•DeepDepth  
•MaxDepth  
•Deep  
•Shimmery  
•SpcScrmblr  
•Warm0ms  
•Warm60ms  
•Warm120ms  
•0msHPass1  
•0msHPass2  
•0msHPass3  
•0msHPass4  
•0msLPass1  
•0msLPass2  
•0msLPass3  
•0msLPass4  
3-Band Stereo PEQ  
•Flat  
•Low Boost  
•Smiley  
•PhaseInvrtL  
•PhaseInvrtR  
•SmlBoost  
•LowNudge  
•60HzNotch  
•Deep  
Pitch Shifters  
Whammy  
Delays  
•Octave Up  
•Octave Down  
•2ndMin3rd  
•2ndMaj3rd  
Delay  
Long Delay  
•2.8sec/15%  
•CombFilter  
•Slapback  
•300msEcho  
•400ms/30%  
•500ms//25%  
•800ms/20%  
•1 SecEcho  
•1400ms/15%  
•CombFilter  
•Doubling  
Flangers  
Dual Flange  
•HiSweep30%  
•HiSweeep70%  
•LoSweep30%  
•LoSweep70%  
•Throaty  
Smooth Pitch  
•ShftDn-12  
•ShftDn-5  
•ShftDn-24  
•ShftUp+5  
•ShftUp+7  
•ShftUp+12  
•Slapback  
6-Band Mono PEQ  
•Flat  
•Low Boost  
•Smiley  
•60HzNotch  
•InvrtPhase  
Rotary Speaker  
•SloLeslie  
•MedLeslie  
•300msEcho  
•400ms/30%  
•500ms/25%  
•800ms/20%  
•1SecEcho  
•FastLeslie  
•Nasally  
•Gonzo  
•IntenseL  
•Intense R  
•FlaChorus1  
•FlaChorus2  
•MaxRepeats  
•2.8sec/0%  
Stereo Tremolo  
•DeepSlow  
•DeepMedium  
•DeepFast  
•MildSlow  
•MildMedium  
•MildFast  
•MaxRepeats  
•1400ms/0%  
6-Band Stereo PEQ  
•Flat  
•Low Boost  
•Smiley  
•60HzNotch  
•PhasInvrtL  
Dual Pitch  
•5th/OctUp  
•5thUpOctDn  
•Min3/5thUp  
•4thOctDn  
Analog Delay  
•1400ms/25%  
•SoftEcho  
Dual Delay  
•PingPong  
•1SecTicToc  
•Doubling  
Stereo Reverb  
•SmoothHall  
•Bar'nGrill  
•OakFloorRm  
•VocalReverb  
•FoilPlate  
•Eternity  
Stereo Flange  
•HiSweep30%  
•HiSweeep70%  
•LoSweep30%  
•LoSweep70%  
•Throaty  
•OctUp/Dn  
Stereo Analog Delay  
•700ms/25%  
•SoftEcho  
•Eternity  
•DlyCho300m  
•Slapback  
Auto Pan  
•WideSlow  
•WideMedium  
•Wide Fast  
•Narrow Slow  
•Narrow Med  
•Narrow fast  
•OctDown/Dtn  
•5ths Down  
•1&2OctsUp  
•DoubleSlap  
•RoundNRound  
•Hard2Tap  
•Thick Tap  
Thru Module  
•Stereo Thru  
•Mute  
•Left Thru  
•Right Thru  
•GoldPlate  
•SmphnyHall  
•RichChamber  
•Sanctuary  
•SaltPalace  
•CmntGarage  
•PlutoVerb  
34  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Effects Library  
The following pages offer a complete description of all of the effects available in the Johnson Millennium Stereo 250.  
Analog Wah  
With the Analog Wah, you get the best of both worlds. This Analog Wah is digitally controlled. This means that you get an dead-on accurate  
Wah emulation, which is controlled via the Millennium's powerful processing. And the best thing is, you no longer have to change batteries  
every 3 to 4 hours.  
The Analog Wah module also gives you the ability to assign a Dynamic Modifier to the Pedal parameter to create Auto-Wah effects within the  
Wah module.  
Analog Wah Parameters  
On/Bypass  
This parameter turns the Analog Wah On or Bypasses the effect module.  
Wah Position  
Controls the pedal position of the Analog Wah effect module. Ranges from 1 to 128. *An Expression pedal such as  
the expression pedals on the J-12 or a standard volume or voltage control pedal must be assigned to this  
parameter in order for module to operate.  
Wah Type  
Selects which Wah type is to be used. Selections are: Toe heavy, Linear, and Heel Heavy.  
Amplifier Types  
All of the great Amplifier tones of today and the past are present under the hood of the Johnson Amplification Millennium. You can access any  
of these tones by pressing any one of five Amplifier Modeling buttons located on the front panel. Successive presses of each button will move  
you through a variation of the selected Amplifier Model type. They’re all there, but if you want to modify these tones, this can easily be done  
in the Edit mode or on the fly with the tone controls on the front panel.  
Amplifier Type Parameters  
Amp Selector  
This parameter is used to select the different Amplifier types available.  
Channel Selector  
Channel A Gain  
Channel A level  
Channel B Gain  
Channel B level  
Selects which channel of the Amplifier is being used or modified. Selections are channel A or channel B.  
This parameter controls the amount of gain used in channel A. Range is from 0.0 to 10.  
This parameter controls the overall level of channel A. Range is from Off to 100%.  
This parameter controls the amount of gain used in channel B. Range is from 0.0 to 10.  
This parameter controls the overall level of channel B. Range is from Off to 100%.  
35  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Channel A Treble  
Channel A Mid  
Channel A Bass  
Channel B Treble  
Channel B Mid  
Channel B Bass  
Ch A dlvl  
This parameter controls the high EQ frequency used in channel A. Range is from 0.0 to 10.  
This parameter controls the mid EQ frequency used in channel A. Range is from 0.0 to 10.  
This parameter controls the low EQ frequency used in channel A. Range is from 0.0 to 10.  
This parameter controls the high EQ frequency used in channel B. Range is from 0.0 to 10.  
This parameter controls the mid EQ frequency used in channel B. Range is from 0.0 to 10.  
This parameter controls the low EQ frequency used in channel B. Range is from 0.0 to 10.  
This parameter controls the overall digital effects level in channel A. Range is from Off to 100%.  
This parameter controls the overall digital effects level in channel B. Range is from Off to 100%.  
This parameter controls the overall master volume level in channel A. Range is from Off to 100%.  
This parameter controls the overall master volume level in channel B. Range is from Off to 100%.  
Ch B dlvl  
Ch A mlvl  
Ch B mlvl  
Noise Gate  
The Silencer noise reduction system is definitely going to become your best friend in any recording session or live performance for keeping  
signals quiet.  
Noise Gate Parameters  
Type  
Selects the type and placement of the noise reduction to be used. Types include: 1. Silencer 1, 2. Silencer II  
Sets the minimum input level at which the Noise gate will engage. Ranges from -90 to 0.  
Adjusts how far the signal is lowered when the gate is closed. Ranges from 1 to 5.  
Threshold  
Attenuation  
Attack  
Controls how quickly the gate opens after the signal level reaches Thresh. Range: 1 to 10.  
Determines how quickly the the gate closes after the signal falls below the Threshold. Ranges from: 1 to 10.  
Release  
36  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Digital Effects  
Reverbs  
Reverberation is probably the most widely used effect because it allows you to simulate the sound reflection characteristics of almost any kind  
of room. In a real room, reverb is a result of sound reflecting off room surfaces such as the walls, floor, ceiling, and objects in the room. The  
materials, size, and shape of the room determine how long these reflections echo and decay before dying out completely. These factors also  
help determine the audio characteristics of the room, such as how long the high-frequency reverberations ring when compared to the low  
frequencies, or how much initial "slapback" the room wall produces when a sound hits.  
Today’s technology allows the Millennium to offer a complete palette of flexible, easy to use reverbs. There are five basic reverbs to choose  
from:  
1) Reverb - Simple, straight ahead reverb with only the most basic parameters.  
2) Dual Reverb - Multi-dimensional reverb with flexible frequency band-splitting capabilities. The reverb can be  
divided into primary and secondary stages using selectable High or Low Pass cross-overs.  
3) Stereo Reverb - A true stereo version of the Reverb Module.  
4) Spring Reverb - A recreation of the old Spring Tank Reverb found in Vintage and Modern combo Amps.  
5) Gated Reverbs - A very linear, high energy reverb that can be set to decay, stay flat, or ramp up the reverb decay,  
creating many unique ambient effects.  
6) Room Echo - A true stereo, multi-tap delay for creating small ambient spaces. The delays are divided into four  
sections of early reflections. These reflections can be placed anywhere in the stereo field and can be as dense or  
sparse as necessary. The Room Delay also includes a feedback loop for delay regeneration.  
Reverb  
Real life reverberation is the result of sound reflecting off surfaces in a room or hall. It can best be described as millions of small echoes that  
decay over a period of time. The size of the room, the surface type of the walls, or the carpet on the floor all contribute to the way real rever-  
beration behaves and sounds.  
When do I use Reverb? When recording in the studio, nearly always. Many guitar tracks, for example, are recorded in a very sterile  
environment (i.e. very dry), but adding reverb can add lush depth to any guitar track and you can get those great sounds in the Studio or  
Live.  
Why should I use stereo reverb? Digital Effects such as Chorus and Delay produce stereo imaging type effects. Stereo reverb helps  
maintain that original stereo image. But don't forget that millions of hit recordings were made using mono input reverbs that created a  
stereo output image. The theory is that sound generally originates from one point in a room, so mono often works just fine. The rule? Don’t  
get caught using too much reverb on your guitar in live situations. Even if the room is small, it still produces some reverb. Too much makes  
the guitar go away. Let it compliment the room.  
37  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Gated Reverb  
Gated reverb doesn't behave as naturally as the standard varieties of reverb. Originally, it was created by taking a long, dense reverb and  
chopping it short with a noise gate. This made for a burst of reverberation energy that could help thicken up a variety of sounds.  
Digital signal processing techniques improved and soon allowed ways to create similar gated reverb sounds that were far more usable and  
flexible. Today's gated reverb doesn't get gated at all, it just sounds like it does. It is actually a large burst of delay taps that create the gated  
reverb sound. This allows you to chose the length of the effect along with different slope shapes.  
When do I use Gated Reverb? Using a Gated Reverb in a multi effect guitar application is ideal for producing unusual special effects.  
Using the Gated reverb can produce a very rich and intense and ambience which can thicken up a guitar tone in many ways . This type of  
reverb is also ideal for producing an effect that is similar to backward masking.  
Reverb Parameters:  
Note: Not all of the parameters listed below are available in all Reverb modules.  
FX: Lvl  
Dry: Lvl  
Balance  
Type  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the left/right positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Selects the reverb type. Each room type has a different decay range (just as real rooms do), so changing TYPE also  
changes the decay time of the room. Types are: Studio Room, Wood Room, Vocal Plate, Concert Hall, Plate Reverb,  
Chamber, Cathedral, Arena, Cement Shelter, and Infinite Spring (for Reverbs), and: Flat, Shelf, Decaying Linear,  
Decaying Logarithmic, Decaying Exponential, Decaying Sine, Reverse Linear, Reverse Logarithmic, Reverse  
Exponential, Reverse Sine, Peaking Linear, and Peaking Exponential (for Gated Reverbs).  
Density  
Controls the number of discrete room wall reflections during the early portions of DECAY. Higher settings produce  
more reflections while low settings yield fewer initial wall echoes. Use this control in conjunction with DISPERSION  
to build or reduce the thickness of early reflection clusters heard near the beginning of the reverberation. Ranges  
from 0% to 99%.  
Dispersion  
Diffusion  
Controls the distance (time) between the echoes set by DENSITY. If DENSITY is set low and DISPERSION is set high,  
the initial room echoes. Dispersion can be heard as discrete echoes followed by smoother room reverberations. Set  
DISPERSION low for a dense cluster of reflections during the early portions of DECAY. Ranges from 1 to 5.  
Simulates the presence of different room materials by controlling the smoothness of reverberations through the  
course of DECAY. Low DIFFUSION settings are great for simulating hard, flat surfaces while higher DIFFUSION  
settings can be used to simulate the presence of irregular surfaces in the room such as natural rock masonry or man-  
made diffusers. Unlike flat surfaces, these materials reflect (diffuse) the sound in many directions because of the irreg-  
ularity of the surfaces themselves. This builds smoothness over the reverb progression. Ranges from 0% to 99%.  
38  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
X-Over Type  
X-Over Freq.  
Selects which crossover type will be used for the Primary Secondary reverb stages. The two crossover types are High  
Pass (HP) and Low Pass (LP).  
Selects the Frequency where the crossover begins to function. Ranges from 25Hz to 20kHz.  
Prim & Secd X-Over These two Parameters allow the crossover to be turned On or Off for each reverb stage. When Off, that particular  
stage will be full bandwidth, otherwise its frequency response is limited by the X-Over Type and Frequency  
Parameters.  
Prim & Secd Damp  
Adjusts how quickly the room absorbs the high-frequency reverberations. In a real room, absorptive materials can be  
used to dampen the natural high-frequency reverberations of the room. High settings of DAMP cause the reverbera-  
tions to darken tonally and become less defined over the course of DECAY. Low settings cause less dramatic room  
effects on the tone of the reverberations. Ranges from 1 to 7.  
Low Pass  
Time  
Selects the frequency above which all frequencies are rolled off. This control can be used to darken the response of  
bright-sounding gated reverbs. Ranges from 100 Hz to 8 kHz in the Gated Reverb and from 100 Hz to 20 kHz in the  
Stereo Gated Reverb.  
Controls the length of the gated reverb in milliseconds (much like the DECAY control of a normal reverb). Ranges  
from 25 milliseconds to 300 milliseconds in the Gated Reverb and from 500 milliseconds in the Stereo Gated  
Reverb.  
Blend  
Cross-mixes reverberations from the left side into the right side and vice-versa. This can be used to increase the  
realism of the simulated room by adding reverberations from different parts of the room to each channel. Ranges  
from 0% to 99%.  
Prim & Secd Blend  
Decay  
Adjusts the amount of BLEND for the Primary and Secondary reverb stages. See BLEND above for a complete  
parameter description.  
Controls the length (RT60) of the room reverberations. This one control could have been divided among Size and  
Reflection controls but has been simplified here for easier use. To simulate a large room, use longer DECAY settings.  
For small rooms, use shorter DECAY settings. For more natural sounding reverbs, you may also want to decrease the  
DENSITY setting as DECAY is shortened. Ranges from .5 to 23 seconds depending on the Reverb Type currently  
selected.  
Prim & Secd Decay  
Controls the length (RT60) for the Primary and Secondary reverberation stages. This Parameter interacts with the  
SIZE and REFLCT Parameters. Larger SIZE and REFLCT settings will allow longer reverb decay times while smaller  
settings reduce the length of the reverb decays but produce better small environment emulations. Ranges from .26  
to 11 seconds.  
Prim & Secd Size  
Prim & Secd Reflct  
Changes the relative room size of the Primary and Secondary reverb stages. Ranges from 1 to 5.  
Controls the simulation of energy loss of sound each time it is reflected. Hard, smooth materials like glass and wood  
have more reflectivity that softer, more porous materials. This control can be thought of as determining the  
“liveness” of the room. Ranges from 1 to 10.  
39  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Note: The following Delay parameters that are utilized within the Reverb section are to be used in the Room Echo reverb module.  
Delay A  
Delay B  
Delay C  
Delay D  
Out A - D  
Bal A - D  
Shape  
Sets the length of time before hearing Delay Group A. Ranges from 0 to 120 milliseconds.  
Sets the length of time before hearing Delay Group A and Delay Group B. Ranges from 0 to 120 milliseconds.  
Sets the length of time before hearing Delay Group B and Delay Group C. Ranges from 0 to 120 milliseconds.  
Sets the length of time before hearing Delay Group C and Delay Group D. Ranges from 0 to 120 milliseconds.  
Controls the output level of the Delay Groups. Ranges from Off to 100%.  
Controls the left/right balance of the Delay Groups. Ranges from -99 to 99.  
Selects the shape of the output levels for the delay group taps. Shape selections are: Flat, Peak, Decreasing,  
Increasing, Shelf, and Reverse Shelf.  
Spread  
Controls the width of the effect’s stereo imaging. Ranges from 1 to 10.  
FB: Dly  
Sets the amount of time before the delay is fedback in. Ranges from 0 to 170 ms.  
Sets how much delay is fedback into the signal. Ranges from Off to 50%.  
Amount  
Out L - R  
Prim Out L  
Prim Out R  
Secd Out L  
Secd Out R  
Adjusts the overall level of the left/right side of the reverb. Ranges from Off to 100%.  
Adjusts the overall level of the left side of the Primary reverb. Ranges from Off to 100%.  
Adjusts the overall level of the right side of the Primary reverb. Ranges from Off to 100%.  
Adjusts the overall level of left side of the Secondary reverb. Ranges from Off to 100%.  
Adjusts the overall level of the right side of the Secondary reverb. Ranges from Off to 100%.  
Choruses and Flangers  
Both choruses and flangers use a Low Frequency Oscillator (LFO) to produce their rich, swirling effects. When you change the speed and depth  
Parameters of modulation effects, you're actually controlling the frequency and amplitude of the LFO. These settings determine the rate and  
intensity of the modulation effect.  
In general, here's how a chorus works: after entering the module, the source signal is split into two paths. One is allowed to pass through  
the Module unaltered, while the other is delayed and pitch modulated with an LFO. The modified sound is then sent to the output, along  
with the original. In Fig. 4-1 below, a sine wave is used to modulate the pitch of the split sound source.  
40  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
The Dual Chorus creates two different pitch “voices”, while the Octal Chorus creates eight voices for extremely full, rich sounds .  
1 sec  
2 sec  
3 sec  
Modulated Sound  
Original Sound  
T I M E  
Figure 4-1 Modulation Example  
The only difference between choruses and flangers is that flangers use less delay and have a feedback parameter that sends a portion of the  
effected signal back to the input of the module. When the effected signal reaches the input, it is sent through the module again, building  
thickness and depth. If you increase the feedback enough, the source begins to lose its own original pitch to the dramatic pitch modulation of  
the feedback loop.  
LFO Waveforms: There are four LFO waveforms available for Choruses, Flangers, Phasers, Tremolos, Auto Panners. They include SINe,  
TRIangle, SPecial-1, SPecial-2, and SPecial-3. See figure 4-2 for examples of what these waveforms look like.  
FREQUENCY (SPEED)  
FREQUENCY (SPEED)  
FREQUENCY (SPEED)  
FREQUENCY (SPEED)  
FREQUENCY (SPEED)  
SP3 LFO  
SINE LFO  
SP1 LFO  
SP2 LFO  
TRIANGLE LFO  
(Modifiers only)  
Figure 4-2 LFO Types  
Chorus  
Chorus is probably the most basic modulation effect. It is really just a very small delay whose time is always changing. As the time is varied, the  
delayed signal's pitch changes (just like a tape recordings' pitch raises when you play it faster). By moving the time back and forth, you hear a  
sound that goes in and out of tune. When combined with the original sound, it almost sounds like more than one instrument is playing. The  
Millennium uses several choruses at once to make huge rich sounds. For example, the octal chorus uses eight chorus voices at once to create  
an incredible ensemble of sound. Aside from the more obvious speed and depth parameters (which adjust respectively how fast and far the  
sound goes out of tune), the Millennium allows you to use different waveforms. The waveform defines how it will move in and out of tune.  
The triangle waveform is very popular for slow, shallow chorus settings, while the sine waveform works nicely for faster, deeper settings.  
41  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
When do I use Chorus? The Chorus effect is so vast in applications, an easier question would probably be “When can’t I use a Chorus.  
When playing the Blues, turn the Speed and Depth parameters up to produce an almost Leslie-Type effect When trying to add dimension to  
guitar tone, use the Chorus to thicken-up and add depth to your sound. And, any time your using a clean tone program, guitar always  
sounds so lush when chorus is added.  
Chorus Parameters:  
Note: not all of the parameters listed below are available in all Chorus modules.  
FX: Lvl  
Dry: Lvl  
Balance  
Speed  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the left/right positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Controls the Low Frequency Oscillator (LFO) speed of the chorus. Ranges from 0.06 to 16.0 Hz.  
Depth  
Adjusts the intensity of the chorus effect. High settings produce dramatic modulation, while lower settings can be  
used to produce a more subtle, ambient swirling. Ranges from 0 to 30 milliseconds.  
Depth 1 - 2  
DEPTH1 adjusts the intensity of chorus voices 1-4. DEPTH2 adjusts the intensity of chorus voices 5-8. Ranges from 0  
to 30 milliseconds.  
Wander Speed  
Controls the secondary LFO speed of chorus voices 5-8. This is a secondary oscillator for voices 5-8 that causes  
deviations from the oscillation path set by DEPTH2. This control can produce radical new textures when used  
creatively. Try setting it slightly faster or slower than SPEED. Ranges from 0.06 to 2.0 Hz.  
Wander Depth  
Adjusts the intensity of the oscillation deviations produced by WANDER SPEED. WANDER DEPTH produces dramatic  
psycho-acoustic swirling effects when set higher than DEPTH2. Ranges from 0 to 10 milliseconds.  
WvFrm  
Selects which waveform the LFO follows. Options: sine, triangle, SP1 (special 1), and SP2 (special 2). See figure 3-4  
Dly A - B  
Controls the delay time of chorus voices A and B. Higher delay time settings produce a more dramatic sweeping  
sound. Ranges from 0 to 60 milliseconds.  
Dly C - D  
Dly E - H  
Controls the delay time of chorus voices C and D. Higher delay time settings produce a more dramatic sweeping  
sound. Ranges from 0 to 60 milliseconds  
Controls the delay time of chorus voices E through H. Higher delay time settings produce a more dramatic sweeping  
sound. Ranges from 0 to 60 milliseconds  
Out A - B  
Pan A - B  
Adjusts the overall level of chorus voice A or B. Ranges from Off to 100%.  
Controls the placement of chorus voice A or B. Ranges from -99 to 99.  
42  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Out C - D  
Pan C - D  
Out LA - LB  
Out RA - RB  
Spread  
Adjusts the overall level of chorus voice C or D. Ranges from Off to 100%.  
Controls the placement of chorus voice C or D in the stereo image. Ranges from -99 to 99.  
Adjusts the left-side level of chorus voice A or B. Ranges from Off to 100%.  
Adjusts the right-side level of chorus voice A or B. Ranges from Off to 100%.  
Controls the width of the effect’s stereo imaging. The higher the setting, the wider the image. The lower the setting,  
the more monophonic the effect becomes. Ranges from 1 to 10.  
Flanger  
A Flanger is just a chorus that loops back into itself, causing what can be described as a tubular sound (since it sounds much like the  
reflections heard inside a large cement or metal pipe). It is still a modulating effect, so you hear a lot of sweeping movement. This makes the  
flanger a very colorful effect that can be easily overused if you're not careful. The more you feed the flanger back to itself, the more intense the  
sound becomes.  
When do I use Flanger? An electric guitar is a sound that can utilize the flanger effect. It works very well with both clean and distorted  
guitar sounds. By setting the Speed and Depth parameters to higher settings, this will add more depth and body to the overall guitar signal.  
Flanger Parameters  
Note: Not all of of the parameter listed below are available in all of the Flanger modules.  
FX: Lvl  
Dry: Lvl  
Balance  
Speed  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Controls the Low Frequency Oscillator (LFO) speed of the flanger. Ranges from 0.06 to 16.0 Hz.  
Depth  
Controls the intensity of the flange effect. High settings of DEPTH combined with high settings of FDBCK produce  
dramatic, synth-like textures. Ranges from 0 to 30 milliseconds.  
FdBck  
Controls how much of the flanged signal is fed back to the input of the Module. The FDBACK Parameter is what  
gives flangers their distinctive voice. Flangers are capable of both positive and negative feedback loops, so  
experiment to find the sound you like best. Ranges from -99% to 99%.  
WvFrm  
Selects which waveform the LFO follows. Options for this control include sine, triangle, SP1 (Special 1), and SP2  
(Special 2). The sine wave setting is probably the most easily recognized, but the smooth response of the triangle  
wave or the intensity of SP1 or SP2 typically produce better results. See figure 4-2.  
43  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Dly A - B  
Controls the delay time of flange voice A or B. Shorter delay times produce a more dramatic, deeper sweeping sound.  
Ranges from 0 to 60 milliseconds.  
Out A - B  
Pan A - B  
Out L - R  
Adjusts the overall level of flange voice A or B. Ranges from Off to 100%.  
Controls the stereo soundfield placement of flange voice A or B. Ranges from -99 to 99.  
Controls the output level of the left or right side of the flanger. Ranges from Off to 100%.  
Phasers  
The Phaser or “Phase Shifter” as it is sometimes called, is a classic effect from the 70's that uses phase cancellation to create a warm sweeping  
effect. The effect is created by making a copy of a signal and moving it in and out of phase while mixing it with the original signal. As it moves,  
different frequencies are cancelled out creating a smooth curling sound. There is also a feedback control that sends the shifting signal back into  
the phaser's input. This intensifies the sound even more.  
When do I use a Phaser? A great example of this can be heard most when you listen to music of the 70’s. Guitarist of the day loved their  
Phasers. A Phaser is a great effect to use when playing clean and funky rhythms.  
Phaser Parameters:  
Dry: Lvl  
Balance  
Speed  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Controls the Low Frequency Oscillator (LFO) speed of the phaser. Ranges from 0.06 to 16.0 Hz.  
Depth  
Controls the intensity of the phaser effect. High settings of DEPTH combined with high settings of FDBCK produce  
dramatic, synth-like textures. Ranges from 0 to 30 milliseconds.  
FdBck  
Controls how much of the flanged signal is fed back to the input of the Module. The FDBACK Parameter is what gives  
phasers their distinctive resonating sound. Ranges from -99% to 99%.  
WvFrm  
Selects which waveform the LFO follows. Options for this control include sine, triangle, SP1 (Special 1), and SP2  
(Special 2). The sine wave setting is probably the most easily recognized, but the smooth response of the triangle  
wave or the intensity of SP1 or SP2 typically produce better results. See figure 4-2.  
Out A - B  
Pan A - B  
Out L - R  
Adjusts the overall level of phaser voice A or B. Ranges from Off to 100%.  
Controls the stereo soundfield placement of phaser voice A or B. Ranges from -99 to 99.  
Controls the output level of the left or right side of the flanger. Ranges from Off to 100%.  
44  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Rotary Speaker Simulator  
The Rotary Speaker Simulator allows you to emulate the classic rotating speaker sound, without the chiropractic problems that come with  
moving bulky speaker cabinets. The Rotary speaker is directly responsible for some of the most unique sounds in music. The applications for  
this effect are so diverse, it can be used to achieve sounds ranging from the Allman Brothers Band to the legendary Stevie Ray Vaughan.  
A unique parameter in the Rotating Speaker simulation is the Acceleration parameter. This parameter is used emulate the the time that it takes  
to get the Speaker up and spinning at full speed. The parameter can be assigned to a footswitch on the J-12 or an External external expression  
pedal so you can control the acceleration speed.  
Rotary Speaker Simulator Parameters:  
FX: Lvl  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right)  
Selects which speed mode the Rotor and Horn are in. Settings are fast or slow.  
Sets the horn stereo microphone spread. Ranges from 0 to 100%.  
Dry: Lvl  
Balance  
Mode  
Spread  
H - R: Level  
Sets the overall level of the Rotor or Horn. Ranges from Off to 100%.  
Slo - Fast Hrn Speed Controls the Low Frequency Oscillator (LFO) speed of the Horn. Ranges from 0.06 to 16.0 Hz.  
Slo - Fast Hrn Depth Controls the intensity of the rotating effect. Ranges from 0 to 30 milliseconds.  
Slo - Fast Hrn Doppler Sets the amount of shifted pitch heard in the Horn. Ranges from 0 to 50 milliseconds.  
Slo - Fast Rtr Speed  
Slo - Fast Rtr Depth  
X-Over  
Controls the Low Frequency Oscillator (LFO) speed of the Rotor. Ranges from 0.06 to 16.0 Hz.  
Controls the intensity of the rotating effect. Ranges from 0 to 30 milliseconds.  
Selects the frequency where the signal is split between the Horn and Rotor. Ranges from 25Hz to 20kHz.  
Acceleration: H - R  
Sets the amount of time that the Rotor and Horn take to come up to their full rotating speed. Ranges from 0 to 10  
seconds.  
45  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Tremolo and Auto-Panner  
With such a re-surgence in vintage tone and gear Tremolo and Auto panner effects of the 50’s and 60’s are back and more popular than ever.  
These effects that revolutionized “Surf-Style” music can be heard all everywhere in the 90’s. Tremolos and auto panners are similar to one  
another in that they both use an LFO to modulate input levels to produce vibrato effects.  
Tremolo  
The word tremolo actually has several definitions in the music world. It basically means that a sound is being modulated in amplitude (the  
volume is beating or pulsing). It could be emulated by turning a volume knob up and down. But you probably have better things to do than  
turn a volume control up and down throughout a whole song, so let the Millennium do it for you.  
Aside from speed and depth parameters, the tremolo also has an LFO waveform that determines the way a signal's volume is increased and  
decreased. While the Sine wave is probably the most common to the ear, the Triangle and Special 2 waveforms are progressively more intense.  
When do I use Tremolo? Tremolo is truly a vintage sound for the guitar, electric piano and organ. Most pronounced on the guitar, you  
can hear it used on everything from sweet ballads to blues rock 'n roll.  
Auto Panner  
The auto panner is basically a dual version of a tremolo. It changes the amplitude of the left signal just as a tremolo does, but the amplitude of  
the right signal is inverse to that of the left signal. This gives the illusion that the signal is moving back and forth between the left and right  
speakers.  
The Auto Panner's Speed typically doesn't get set as fast as the Tremolo since you usually want a sound to move smoothly back and forth in the  
stereo image. The Millennium auto panner is especially flexible since it can be used for either mono or stereo input sources. When used with a  
mono source, the signal pans back and forth as described earlier. When a stereo sound source is used, the original stereo image is maintained  
by moving the volume of the left signal exactly opposite of the right signal. The stereo image fades back and forth between the stereo extremes.  
When do I use an auto panner? The auto panner can be a very creative tool. When running your guitar rig in a stereo set-up with the  
right amount of cabinet separation, the Auto-Panner creates a stereo panning effect that is right out of this world.  
Auto panners can also add life to delays or choruses by moving them around instead of just sitting in one place in the mix. Simply place an  
auto panner module after a delay or chorus module. You don't need to set the auto panner's depth parameter too deep since you just want  
some gentle movement.  
Tremolo & Auto Panner Parameters:  
FX: Lvl  
Speed  
Depth  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the Low Frequency Oscillator (LFO) speed of the effect. Ranges from 0.06 to 16.0 Hz.  
Controls the intensity of the effect. As DEPTH increases, volume changes become more dramatic. Ranges from 0 to 30  
milliseconds.  
46  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
WvFrm  
Selects which waveform the LFO follows. Options for this control include sine, triangle, SP1 (Special 1), and SP2  
(Special 2). The sine wave setting is probably the most easily recognized, but the smooth response of the triangle  
wave or the intensity of SP1 or SP2 typically produce better results. See figure 4-2 on page 41.  
Pitch Shifters and Harmony  
The pitch shifter allows you to move sound from one pitch to another. It accomplishes this by recording a small part of the original sound and  
then playing it back either faster (to raise the pitch) or slower (to lower the pitch). It does this over and over again to create a new pitch.  
The Harmony modules give you almost unlimited possibilities. you can use different harmony intervals to produce slide guitar effects. or Major  
or Minor 3rd intervals to create dual soloing lines reminiscent of the Eagles’ “Hotel California”.  
When do I use pitch shifting? Guitarists are probably the most well known users of pitch shifters. They commonly pitch shift their  
sound down by an octave to get a deep rumble out of their distortion, or shift it an octave up to emulate a 12 string guitar.  
Both guitar and synth players have created some amazing textures by pitch shifting their sound up a fifth (7 semitones). This creates more  
complex chords out of simple ones (e.g. a basic Cmaj chord sounds like a Cmaj9 chord, or Cmin7 becomes a Cmin11 chord). Lead lines  
sound amazing when using major 5th intervals up.  
Pitch Shifters Parameters  
Note: not all of the parameters listed below are available in all Pitch Shifter modules.  
FX: Lvl  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Dry: Lvl  
Balance  
Shft A - B  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right)  
SHFTA and SHFTB control the pitch intervals between the original note and voices A and B of the pitch shifter. Pitch  
shifters can be used for a wide variety of effects, including doubling, octave division, and chromatic harmonies. Each  
Pitch Shifter has a 4-octave range, stepped in semitones from -24 to +24.  
Dtn A - B  
Controls the detuning amount for pitch-shifted voices A and B. As DTN moves away from zero, dissonance becomes  
more pronounced. Low DTN settings can be useful for thickening or enhancing the imaging of the source material.  
Ranges from -50% to 50%.  
Shft C - D  
Dtn C - D  
See Shift A - B.  
See Dtn A - B.  
47  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Shft E - H  
Dtn E - H  
Key  
See Shift A - B.  
See Dtn A - B.  
Sets the diatonic key for the harmonies. If the song you are playing is in the key of G Major, you would select G for  
the scale.  
Scale  
Sets the scale type for the Harmony you want to hear. Scale types include: Major, Minor, Harmonic Minor, Melodic  
Minor. Dorian, Mixolydian, Lydian, Lydian Augmented, Major Pentatonic, Minor Pentatonic, Blues, Whole Tone, Half-  
Whole,and Whole-Half.  
Interval  
Sets the basic interval of the Harmony. You can choose from one of several Harmony intervals. See the Harmony  
Interval Charts for reference.  
Out A - B  
Pan A - B  
Out C - D  
Pan C - D  
Out E - H  
Pan E - H  
Adjusts the overall level of pitch-shifted voice A or B. Ranges from Off to 100%.  
Controls the placement of pitch-shifted voice A or B in the stereo image. Ranges from -99 (all left) to 99 (all right).  
Adjusts the overall level of pitch-shifted voice C or D. Ranges from Off to 100%.  
Controls the placement of pitch-shifted voice C or D in the stereo image. Ranges from -99 (all left) to 99 (all right).  
Adjusts the overall level of pitch-shifted voice E through H. Ranges from Off to 100%.  
Controls the placement of pitch-shifted voice E through H in the stereo image. Ranges from -99 (all left) to 99 (all  
right).  
Out L - R  
Out LA - LA  
Out RA - RB  
Spread  
Adjusts the left or right output level of the pitch-shifted voice. Ranges from Off to 100%.  
Adjusts the left-side level of pitch-shifted voice A or B. Ranges from Off to 100%.  
Adjusts the right-side level of pitch-shifted voice A or B. Ranges from Off to 100%.  
Controls the width of the effect’s stereo imaging. The higher the setting, the wider the image The lower the setting,  
the more monophonic the effect becomes. Ranges from 1 to 10.  
Detuners  
The detuner effect does exactly what its name implies; it detunes a sound (moves it out of tune) and allows you to add it to the original sound.  
The result can be almost chorus-like, but it doesn't move like the chorus effect does. This actually makes the detuner more transparent and not  
quite as thick as the chorus effect, which in many applications is a good thing (since effects can quickly pile up and clog up great sounding  
audio).  
48  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
When do I use a detuner? The detuner falls into the same guidelines as the chorus effect. It works with just about everything; It is ideal  
for thickening up a rhythm guitar track. Remember to experiment with the delay parameters if you are looking for a wider detuning sound.  
Adding 30-60 ms of delay to the detuner's voices that are panned hard to one side (while not delaying the other side) will change the  
detuner's stereo imaging greatly.  
Detuner Parameters  
FX: Lvl  
Controls the signal input level fed to the module. Ranges from Off to 100%.  
Dry: Lvl  
Balance  
Dtn A - B  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Controls the detuning amount for detuner voices A and B. Higher detune settings produce a more dissonant sound.  
Ranges from -50% to 50%.  
Dtn C - D  
Dtn E -H  
Dly A - B  
Controls the detuning amount for detuner voices C and D. Ranges from -50% to 50%.  
Controls the detuning amount for detuner voices E through H. Ranges from -50% to 50%.  
Controls the amount of time before detuner voices A and B are heard. Higher delay time settings produce a short  
slapback delay effect. Ranges from 0 to 60 milliseconds.  
Dly C - D  
Dly E - H  
Out A - B  
Pan A - B  
Out C - D  
Pan C - D  
Out LA - LB  
Out RA - RB  
Spread  
Controls the amount of time before detuner voices C and D are heard. Ranges from 0 to 60 milliseconds.  
Controls the amount of time before detuner voices E through H are heard. Ranges from 0 to 60 milliseconds.  
Adjusts the overall level of detuner voice A or B. Ranges from Off to 100%.  
Controls the stereo soundfield placement of detuner voice A or B. Ranges from -99 (all left) to 99 (all right).  
Adjusts the overall level of detuner voice C or D. Ranges from Off to 100%.  
Controls the stereo soundfield placement of detuner voice C or D. Ranges from -99 (all left) to 99 (all right).  
Adjusts the left side level of detuner voice A or B. Ranges from Off to 100%.  
Adjusts the right side level of detuner voice A or B. Ranges from Off to 100%.  
Controls the width of the effect’s stereo imaging. The higher the setting, the wider the image. The lower the setting,  
the more monophonic the effect becomes. Ranges from 1 to 10.  
Delays  
A delay produces discrete, repeating echoes of the source material at a specified interval. In digital delays, the input signal is "sampled" or  
49  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
recorded into memory, where it is held for the amount of time you specify with the delay time setting, after which the sample is replayed at the  
output. The Millennium delays have a feedback meter that is used to send a portion of the delayed signal back to the input to be re-recorded  
along with new source material. The feedback setting determines how long the delay repeats take to decay to inaudibility.  
When do I use delay? When you’re the lone guitarist in a band, the Delay can be your best friend. The Delay repeats can create the  
illusion that there is more than one guitar being played. One trick to using delays effectively is setting the delays to fall in time with the  
music. This used to mean grabbing a calculator, dividing 60 by the tempo (beats per minute), then dividing that answer by the desired sub-  
beats . . . Sound like a hassle? Yeah, we thought so too. So the Millennium takes care of all the calculations for you! All you have to do is tap  
the TapIt <button> or (assign the tapit parameter to a footswitch on the J-12 or J-3) and manually tap in the desired delay time and the new  
time is added.  
Another common use for delay is for stereo imaging. Very small amounts of delay (10-25ms) can be used to make a signal sound like it is  
panned to one side. This trick works because of the way the brain interprets sounds. When your left ear hears something before the right  
ear, it thinks that the source of that sound is found somewhere to your left. You can also use delays set at 30-60ms, which spreads a sound to  
the extremes of the stereo image. Be careful with this technique if your mix has a chance of being listened to in mono.  
Delay Parameters  
Note: not all of the parameters listed below are available in all Delay modules.  
FX: Lvl  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Dry: Lvl  
Balance  
Dly Time  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Sets the maximum delay time available to each delay voice. For example, if DELAYTIME is set to 1000 ms, each delay  
voice can be set from 0 to 100% of that delay time. Ranges from 0 to 1.4 seconds (Maximum delay times differ  
between 1/4, 1/2, 3/4, and FUL module sizes.) Half bandwidth delay times automatically double the set delay time  
used used.  
FdBck  
TapIt  
Controls the fade time of the delay repeats. Higher settings take longer to fade out, while a setting of zero could be  
used to limit the delay to one repeat per voice. The delay provide both positive and negative feedback settings.  
Ranges from -99% to +99%.  
Allows you to change DELAYTIME in real-time, by tapping the TAPIT button at the tempo you want. Delay voice  
percentages do not change when using this control.  
Smear  
LPF  
Sets the spread of Diffusion of the Delay Repeats. Ranges from 0 to 100%.  
Selects where the Low Pass Filter is positioned within the Delay module. Positions are: Pre Delay or Post Delay.  
Selects the Frequency band that appears in the LPF. Ranges from 25 Hz to 20 kHz.  
Frequency  
50  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Gain  
Controls the output gain of the LPF. Ranges from -12 to 12.  
Dly A - B  
Controls the percentage of DELAYTIME allocated to delay voices A and B. For example, if DELAYTIME (above) is set  
to 1000 ms and DLYA is set to 75%, the voice A delay time is 750 ms. Remember, each voice in the Module can have  
any delay time up to 100% of DELAYTIME. Ranges from 0% to 100%.  
Dly C - D  
Out  
See Dly A - B.  
Adjusts the overall level of the Delay. Ranges from Off to 100%.  
Pan  
Controls the stereo soundfield placement of the delay. Ranges from -99 (all left) to 99 (all right).  
Adjusts the left or right output level of the Delay. Ranges from Off to 100%.  
Adjusts the output level of delay voice A or B. Ranges from Off to 100%.  
Controls the stereo soundfield placement of delay voice A or B. Ranges from -99 (all left) to 99 (all right).  
Adjusts the output level of delay voice C or D. Ranges from Off to 100%.  
Controls the stereo soundfield placement of delay voice C or D. Ranges from -99 (all left) to 99 (all right).  
Adjusts the left-side output level of delay voice A or B. Ranges from Off to 100%.  
Adjusts the right-side output level of delay voice A or B. Ranges from Off to 100%.  
Adjusts the left-side output level of delay voice C or D. Ranges from Off to 100%.  
Adjusts the right-side output level of delay voice C or D. Ranges from Off to 100%.  
Out L - R  
Out A - B  
Pan A - B  
Out C - D  
Pan C - D  
Out LA - LB  
Out RA - RB  
Out LC - LD  
Out RC - RD  
Compressor  
Compressor Parameters  
Level  
Controls the signal input level fed to the module. Ranges from Off to 100%.  
Threshold  
Ratio  
Sets the threshold level of the compressor. Ranges from -27 to 0.  
This parameter sets the compressor ratio. Ranges from 1.5 to 40.  
Gain  
This parameter controls the amount of gain in the compressor. Ranges from 0 to 200%.  
This parameter controls the attack time of the compressor. Settings are: Slo, Med and Fast.  
This parameter sets the release of the compressor. Settings are: Slo, Med and Fast.  
Attack  
Release  
51  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Delay  
This parameter sets the delay time of the compressor. Ranges from 0 to 10 ms.  
Equalizers  
The Millennium has a broad selection of equalizer Modules to cover virtually any need. If you need bigger Guitar tone, the EQs will give it to  
you. Both mono and stereo modules are available. Remember that mono equalizers connected to stereo sources will always sum the stereo  
signal together for equalization (thus eliminating the stereo image). If you need to maintain the stereo image, use a stereo equalizer module.  
The Parametrics allow you to cover very specific regions of the sound spectrum with extreme precision and control. Up to 6 bands of either  
stereo, or mono parametric equalization are available.  
The Graphic equalizers use 1/3, 2/3, or 1 2/3 octave ISO-standard frequency centers. Equalization or EQ is probably one of the most  
valuable tools the Millennium offers. EQ allows you to change the level of certain frequencies of a sound, and it comes in two different basic  
flavors: graphic and parametric. Graphic is the most common and easiest to use, but the parametric offers much more flexibility and power.  
When do I use EQ? This may seem overly simplistic, but you should use EQ whenever your ears tell you to use it! However, you need to  
remember that EQ can do more harm than good when not used carefully. The EQ can take that thin and “Clangy” sounding Guitar and add  
all of the low end in the world that your heart may desire. This can also be used on the other side. If you have a song that needs tight and  
bright rhythm guitar, you can use the EQ modules to take out the Lows and build up your mids  
Here are a couple of simple examples:  
If you feel your guitar tone is just a little dull, try cutting some of the lower frequencies, you always have to boost up  
the guitar’s' high frequencies, because it could quickly become too bright. Often, good EQ techniques use cut more  
than boost. This is where the old saying “less is more” definitely applies.  
If you are having a hard time being heard in the mix, don't make it louder. Listen carefully and see if there is another  
instrument that is conflicting with your Guitar. Adding a little EQ in the right spot of the less dominant guitar will  
allow it to speak a little easier through the rest of the music.  
Graphic Equalizers  
Graphic EQs give you control of the levels for fixed or pre-selected frequencies (bands) that are evenly spaced. The Millennium offers 8 and 15  
band Mono and 8-band Stereo GEQs and a 31 band mono GEQ. They all cover the complete range of frequencies, but the spacing between the  
31 bands is much closer than the 8 bands, therefore offering more exact control of the sound.  
Graphic Equalizer Parameters  
Level  
Controls the signal input level fed to the module. Ranges from Off to 100%.  
Phase  
Inverts the phase of the source signal. Can be set either IN or OUT of phase.  
Phase L - R  
Freq  
Inverts the phase of the left or right side of the stereo source signal. Can be set either IN or OUT of phase.  
Controls the amount of boost / cut applied to the selected frequency. The GEQ 8 uses 1-1/3 octave ISO standard  
52  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
frequency centers, (Hz) while the GEQ15 and GEQ31 use 2/3 octave and 1/3 octave frequencies. Boost/cut range for  
each band is from -12 to 12.  
Parametric Equalizers  
Parametric EQs offer the added flexibility of letting you define the center frequency you want to adjust, and how many frequencies around that  
center frequency you want to affect. Some of the PEQ modules in the Millennium, also include high shelf and low shelf EQ bands. A high shelf  
allows you select a frequency, and the boost/cut parameter changes the level of all the frequencies above that selected frequency. The low shelf  
works the same way but works on frequencies below the selected frequency.  
Parametric Equalizer Parameters  
Level  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Phase  
Inverts the phase of the source signal. Can be set either IN or OUT of phase.  
Phase L - R  
LoShlv Freq  
LoShlv Level  
Band # Freq  
Inverts the phase of the left or right side of the stereo source signal. Can be set either IN or OUT of phase.  
Selects the center frequency of the low-frequency shelving EQ band. Ranges from 25Hz to 20kHz.  
Adjusts the amount of boost or cut applied to the center frequency of the low-frequency shelving EQ band (selected  
by LOSHLV FREQ). Ranges from -12 to 12.  
Sets the center frequency of the selected band. 6-band PEQs have four true parametric bands of EQ plus shelving  
high- and low-frequency controls with variable frequency. Bands 1 and 2 range from 25 Hz to 20 kHz. Bands 3 and 4  
range from 1 kHz to 20 kHz.  
Band # Width  
Controls the bandwidth of the selected frequency. The higher the setting of WIDTH, the more frequency-selective  
the boost/cut becomes. In other words, with low (narrow) WIDTH settings, frequencies around the selected center  
frequency are not affected by the LEVEL setting. As WIDTH increases, frequencies around the center frequency  
become affected by the setting of LEVEL. Range is from 0.08 to 4.00 kHz.  
Band # Level  
HiShlv Freq  
HiShlv Level  
Adjusts the amount of boost or cut applied to the selected frequency. Varies from -12 to 12.  
Selects the center frequency of the high-frequency shelving EQ band. Ranges from 1kHz to 20kHz.  
Adjusts the amount of boost or cut applied to the center frequency of the high-frequency shelving EQ band (selected  
by HISHLV FREQ. Ranges from -12 to 12.  
Multi Effects Modules - Chorus/Delay and Flange/Delay  
The Millennium, Multi Effect Modules allow the User to combine either Delay and Chorus or Delay and Flange within one effect module block.  
This is ideal for situations where the user needs to add another effect to the effect configuration, but is running low on signal processing  
resources. Within the module, there is a unique parameter that allows you route the signal several different ways between the two effects.  
53  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Multi-Effect Module Parameters  
FX: Lvl  
Dry: Lvl  
Balance  
Route  
Controls the signal input level fed to the Module. Ranges from Off to 100%.  
Controls the level of the dry (uneffected) signal. Ranges from Off to 100%.  
Controls the positioning of the dry signal in the stereo soundfield. Ranges from -99 (all left) to 99 (all right).  
Selects the route signal path within the Chorus/Delay, and Flange/Delay Multi effects modules. The 3 settings are: 1)  
Chorus/Flange into Delay with feedback into the Delay 2) Chorus/Flange into Delay with feedback into Chorus/Flange  
3) Delay into Chorus/Flange with feedback thru the Chorus/Flange.  
Speed  
Controls the Low Frequency Oscillator (LFO) Speed of the Chorus or Flanger. Ranges from 0.06 to 16.0 Hz.  
Adjusts the intensity of the Chorus or Flanger effect. Ranges from 0 to 30 milliseconds.  
Depth  
Feedback (Flanger)  
Controls how much of the flanged signal is fed back to the input of the Module. The FDBACK Parameter is what gives  
flangers their distinctive voice. Flangers are capable of both positive and negative feedback loops, so experiment to  
find the sound you like best. Ranges from -99% to 99%.  
WvFrm  
Selects which waveform the LFO follow. Options for this control include: Sine, Triangle, SP1 (Special 1), and SP2  
(Special 2).  
C/F: Delay  
Delay Time  
Feedback  
Controls the delay time of the Chorus or Flanger voice. Ranges from 0 to 40 milliseconds.  
Sets the delay time for the delay tap. Ranges from 0 to 300 milliseconds.  
Controls the fade time of the delay repeats. Higher settings take longer to fade out, while a setting of zero will limit  
the delay to one repeat. Ranges from 0 to 99%.  
TapIt  
Allows you to change the Delay time in real-time by tapping the TAPIT button at the tempo you want. Delay voice  
percentages do not change when using this control.  
Level: C/F/D  
Pan: C/F/D  
Controls the overall output level of each effect block. Ranges from Off to 100%.  
Controls the stereo soundfield placement of each effect block. Ranges from -99 (all left) to 99 (all right).  
Whammy Effects  
In today’s music industry, it seems that every album on the charts, whether it be Country, Rock, Industrial, or Alternative, are using the  
Whammy technology in some shape or form. Whether it be a subtle chorus Detune, or an all out 2 octave Whammy Dive, this thing is a definite  
attention getter, and first-call studio effect. At this rate, the Whammy effect could possibly log-in as much studio time as Chet Atkins.  
54  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 4 Editing Modules  
Whammy Effect Parameters  
Whammy On/Off  
Turns the Whammy module on or off. When the module is turned off, the signal will only continue to pass through  
the module if the dry level is turned up.  
FX Level  
This parameter lets you select the overall FX level mix of the Whammy Effect module. Ranges from: Off to 100%.  
Dry Level  
This parameter lets you select the amount of Dry signal that is included in the Whammy effect. Ranges from: Off to  
100%.  
Balance  
This parameter allows you to pan the Dry signal either to the Right or the Left in the stereo soundfield. Ranges from  
Left 99 to Right 99.  
Min Shift  
Max Shift  
Min Detune  
Max Detune  
Pedal  
This parameter sets the minimum pedal shift level of the Whammy effect. Ranges from: -72 (6 octaves down), to 24  
(2 octaves up).  
This parameter set the maximum pedal shift level of the Whammy effect. Ranges from: -72 (6 octaves down), to 24 (2  
octaves up).  
This parameter sets the minimum pedal level of detune effect. Ranges from: -50% (down 50 cents), to 50% (up 50  
cents).  
This parameter sets the maximum pedal level of detune effect. Ranges from: -50% (down 50 cents), to 50% (up 50  
cents).  
This parameter is used for the assignment of an expression pedal. This parameter also shows the pedal travel range.  
Ranges from: 0 to 100  
Out  
This parameter is used to set the overall output level of the Whammy module. Ranges from: 0 to 100%  
This parameter is used to position the Whammy effect in the Stereo soundfield. Ranges from: Left 99 to Right 99.  
Pan  
Auto Wah  
The Auto Wah is a great effect use when you want a nasally wah-type effect, but you don’t want to do the leg work. The Auto Wah utilizes a  
sensitivity detector that reads the input signal, then simulates the action of a wah pedal.  
Auto Wah Effect Parameters  
Auto Wah On/Off  
Turns the Auto Wah module on or off. When the module is turned off, the signal will continue to pass through the  
module.  
FX Level  
This parameter lets you select the overall FX level mix of the Auto Wah Effect module. Ranges from: Off to 100%.  
Sensitivity  
This parameter adjusts the sensitivity of the detection of the automatic wah. The higher the sensitivity is set, the  
wider the Wah range will be. Ranges from: Off to 100%.  
55  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
Section-5 Advanced Topics  
Assigning Modifiers  
Modifiers are unique tools that can be used to dramatically alter your sound based on information from external expression pedals and  
external footswitches, signal amplitude, the settings of a Low Frequency Oscillator (LFO) or MIDI continuous controller.  
Every preset in your Millennium has a set of Modifiers. Up to 16 modifier links can be assigned to control any parameter. There are five types of  
modifiers that can be linked to a parameter:  
• External expression pedal  
• The foot pedals and switches on the optional Johnson Amplification J-12 foot controller.  
• LFOs  
• MIDI CCs  
• Dynamic (signal amplitude dependent).  
MIDI CCs  
When you use MIDI CCs, the Millennium responds to CC numbers 0-127 and CHP (channel pressure or aftertouch). This means that you could  
assign an expression pedal, a keyboard's modulation or pitch bend wheel, or any other MIDI CC device to control effect parameters.  
LFOs  
When you use LFOs, parameter values can be controlled automatically between a defined minimum and maximum setting at a rate set by the  
user. The Millennium has 2 user definable LFOs in each preset that can be assigned to any parameter.  
For example, you can create an auto panner without using an auto panner module. Simply link an effect's output pan parameter to the LFO  
modifier and the LFO will move that parameter back and forth. This modifier can be a very useful weapon in the ongoing battle of new sound  
creation. There are two LFOs available in each preset that can use unique speeds and waveforms.  
Dynamic Modifiers  
When you use Dynamic modifiers, the parameter values are controlled in relation to the dynamics of the input signal. The possibilities are  
nearly endless, and this is a feature that is exclusive to Digitech and Johnson Amplification.  
For example, you could link the Dynamic Modifier of a preset to control a chorus level. It doesn't sound like much on paper, but imagine the  
expressiveness of this type of effect on the guitar part. As the dynamics of the music increase, the chorus becomes less apparent. Ease up on the  
string attack a little and the chorus increases. ALL IN REAL TIME!  
NOTE: Linking a modifier to a parameter causes the parameter to change as if you were changing it using the <Preset/Effect> wheel. The  
only difference is that the <Store> button and  
icon do not light. Therefore, the default name may display 'Custom' if a  
CHANGED  
parameter is consistently being changed by a modifier. Storing the preset will store these new parameter values.  
56  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
External Expression Pedals  
The rear panel of the Millennium contains 2 external expression pedal inserts that can be linked to control any parameter of the Amplifiers’  
operating system. Either a standard volume or a voltage control pedal can be connected to these insertion jacks. The 2 external expression  
pedals on the J-12 foot controller can be used as well.  
Once the external expression pedal is connected, the assignment procedure to be followed is listed below.  
Linking a Parameter to a Modifier  
To link a parameter to a modifier, please complete the following steps:  
1. Scroll to the parameter you would like to link to a modifier (ie: Delay feedback).  
2. Press the <Assign> twice when using a foot controller button and the display appears something like:  
Avail Link for: FdBack  
1
OFꢀ%kHz  
FmsdB  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
USER  
#
b
L/R OUTS  
PAGE  
1
OF  
4
3. Turn the <1> knob to turn the link for the selected parameter on. The display will look something like this:  
FdBck F.Sw Min[ ]Max  
%kHz  
%kHz  
-99  
%kHz  
oꢀ%kHz F1  
1
nmsdB 2  
msdB 3  
msdB 4  
HldmsdB  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
US1ER9 b  
#
L/R OUTS  
PAGE  
1
OF  
4. Use the <2> knob to scroll through the different modifiers that can be linked to the parameter you want assigned. The selections are:  
MIDI CC’s  
(aftertouch)  
(CC): 0-127 & ChP  
Real Time modifiers (RT):  
LF1, LF2, dY1, & dy2  
External Pedal  
(Ext): Pdl,(Pd3)  
J-12 (F.Pdl & F.Sw): Pdl-2 & F l-10  
when the J-12 is connected.  
NOTE: The MUTE and THRU effect types do not have any Parameters to connect to, so they will not appear in the parameter list.  
5. Use the <3> knob to select the minimum parameter value you want when the controller is in the maximum position.  
6. Use the <4> knob to select the maximum parameter value you want when the controller is in the maximum position.  
NOTE: Make sure you store any changes you want to save before moving on.  
57  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
Setting up an LFO  
To set up an LFO that is linked to an effect parameter, the procedure is as follows:  
1. Enter the Assign mode by pressing the <Assign> button.  
2. Use the <Page> knob to scroll to the LFO page. The display looks something like:  
LFO  
1
WvForm Speed  
%kHz Hz  
%kHz  
Off  
1
ꢀ%kHz  
msdB  
Sin  
2
msdB 3  
msdB 4  
006  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
17  
US1ER9 b  
#
L/R OUTS  
PAGE  
OF  
3. You can use the <1> knob to select which of the two LFOs you want to adjust.  
4. Use the <2> knob to turn the LFO on or off.  
5. Use the <3> knob to change the selected LFO's waveform. You can select either SINe, TRIangle, SPecial1 or SPecial2.  
6. Use the <4> knob to adjust the speed of the LFO cycle.  
Any parameters assigned to the LFOs will now follow the modulating waveform of the LFO you have selected.  
Setting up a Dynamic Modifier  
1. Enter Assign mode by pressing the <Assign> button.  
2. Use the <Page> knob to scroll to the first of two Dyn pages. The display looks something like:  
Dyn  
1
LoThrs HiThrs  
%kHz  
%kHz  
Off  
1
ꢀ%kHz  
msdB  
0
0
2
msdB 3  
msdB 4  
LINK CHANGED LINK CHANGED  
GATE  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
EQ  
L/R OUTS  
2
FACTORY  
PBAAGNEK18OF  
US1ER9 b  
#
L/R OUTS  
3. You can use the <1> knob to select which of the two Dyns you want to adjust.  
4. Use the <2> knob to turn the Dyn on or off.  
5. Use the <3> knob to set the threshold above which dynamic modification of the parameter begins.  
6. Use the <4> knob to set the point at which maximum parameter modification occurs.  
7. Use the <Page> knob to scroll to the next Dyn page.  
58  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
8. Use the <2> knob to adjust the attack time of the Dyn.  
9. Use the <3> knob to adjust the hold time of the Dyn.  
10. Use the <4> knob to adjust the release time of the Dyn.  
Morphing Pedal Assignments  
The Johnson Amplifier modules and the effect configurations within the Millennium have special morphing capabilities that allow you to  
morph between one amplifier type to another in selected amplifier models. This feature is also available in certain effect configurations so you  
can pan between effects. This will allow you to either morph from a distorted Tube amplifier type, to a clean Solid State amplifier type or  
morph between digital effects. Morphing can be done by linking an expression pedal to the Morph pedal parameter.  
Amplifier Morphing  
To assign the morphing pedal to morph between amplifier types use the following procedure.  
1. Amplifier type morphing must be done using a Johnson Amplifier model. So, from Preset mode, press the <Johnson> button until the  
signal path in the display shows an amplifier model that uses dual amplifier modules and is displayed something like this:  
Fender/Soldano  
2
Chan  
%kHz  
%kHz  
msdB  
msdB 4  
J01  
TUBE  
b
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
LINK CHANGED  
WAH  
EQ  
EQ  
L/R OUTS  
2
DIST  
FACTORY  
PAGE  
USER  
#
BANK 1  
OF  
5
b
L/R OUTS  
2. Using either the <Channel> button or the <4> knob, press (or turn) until both of the channel (A&B) LEDs light and the display  
appears like this:  
Fender/Soldano  
2
Chan  
%kHz  
%kHz  
msdB  
msdB 4  
A-b  
LINK CHANGED  
J01  
TUBE  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
EQ  
EQ  
L/R OUTS  
2
DIST  
FACTORY  
PAGE  
USER  
#
BANK 1  
OF  
5
b
L/R OUTS  
3. At this point, you want to assign the Morphing pedal by pressing the <Config> button and the display will appear something like this:  
Config: Series  
1
2,2  
1
ꢀ%kHz  
msdB  
LINK CHANGED LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
BANK 1  
OF  
2
b
L/R OUTS  
59  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
4. Now using the <Page> knob, turn to page 2 and the display will appear like this:  
Vol Pdl  
1
Morph Pdl  
3
10ꢀ%  
0
0%  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
BANK 2  
OF  
2
b
5. By turning the <3> this will activate the Morph pedal parameter making it ready for assignment. Now press the <Assign> button and the  
display will appear something like this:  
Select a Contrl F.Switch  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
2
FACTORY  
USER  
#
b
L/R OUTS  
6. Now select the expression pedal to be assigned. This can be either one of the two expression pedal inserts located on the rear of the unit,  
or one of the two expression pedals on the J-12 foot controller and the display will appear something like this:  
Morph Exp 1 Min [99] Max  
4
1
2
3
On  
0
TUBE  
DIST  
-99  
99  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
EQ  
EQ  
L/R OUTS  
2
FACTORY  
US1ER9 b  
#
L/R OUTS  
PAGE  
1
OF  
7. In this example, Expression pedal 1 of the J-12 is now assigned to morph between Solid State and Tube distortion models. Note that -99 as  
the minimum value represents the Solid State (bottom) Amp and the maximum being 99, represents the Tube (top) distortion. To return  
to Preset mode, press the <Preset> button. Always remember to save any changes.  
Morphing Between Effect Modules  
Not only does the Millennium allow you to morph between Amplifier modules, but it also gives you the ability to morph between effect  
modules. This can be done when using Effect Configurations 6, 12 or 15 which are split configurations.  
The procedure for assigning the morph pedal to the effect modules uses the same steps as 3 through 7 of the Amplifier Morphing assignment  
procedure.  
Volume Pedal Assignments  
Volume control can be assigned to any preset within the Millennium. When volume control is used in a selected preset, you have the option of  
using either one of the two Expression pedal inserts (located on the rear of the unit), or the expression pedal available on the optional J-12 foot  
controller.  
The procedure for assigning volume control to any preset of the Millennium is as follows:  
60  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
1. From Preset mode, you must get to the configuration screen by either pressing the <Edit> button and turning the <Preset/Effect>  
wheel, or simply press the <Config> button until the display appears something like this:  
Config: Series  
1
2,2  
1
ꢀ%kHz  
msdB  
LINK CHANGED LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
BANK 1  
OF  
2
b
L/R OUTS  
2. Now turn the <Page> knob to page 2 and the display will appear like this:  
Vol Pdl  
1
Morph Pdl  
%
%
3
LINK CHANGED  
GATE  
100  
0
LINK CHANGED  
LINK CHANGED  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
BANK 2  
OF  
2
b
3. Now turn the <1> knob, making the Volume Pedal parameter active for assignment to an expression pedal. Now press the <Assign>  
button and the display will appear like this:  
Select a Contrl F.Switch  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
DIST  
EQ  
EQ  
L/R OUTS  
2
FACTORY  
USER  
#
b
L/R OUTS  
4. Now all you have to do is select the expression pedal that you want to assign the volume pedal parameter control to and move the pedal  
and the display will appear something like this:  
Vol Pd Exp 1 Min[100]Max  
nmsdB 2  
Oꢀ%kHz Pdl  
Off  
100  
1
3
4
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
GATE  
WAH  
TUBE  
EQ  
EQ  
L/R OUTS  
2
DIST  
FACTORY  
US1ER9 b  
#
BANK 1  
OF  
L/R OUTS  
PAGE  
5. Now that the assignment has been made, make sure that you store your changes and press the <Preset> button to return to Preset  
mode.  
61  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
MIDI Functions  
In this day and age where the role of the Guitarist has taken on so many new responsibilities, his or her equipment has to be fast, and has to be  
able to communicate with other devices at the drop of a hat. So, we at Johnson Amplification have made the Millennium a fully MIDI  
implemented device.  
Setting the MIDI Channels  
This option sets the MIDI Channel that the Millennium will respond to MIDI preset changes and CC messages and transmit preset changes on.  
MIDI channel settings include: Off, 1, 2,...15, 16, and All.  
To change the MIDI channel assignment, do the following:  
1. Go to Page 3 of the Utility menu by pressing the <Utility> button and then turn the <Page> knob. The display reads:  
MIDI: RcvChnl TransChnl  
2
ꢀ%kHz  
msdB  
1%kHz  
msdB  
1
%kHz  
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
OF  
US1ER6 b  
#
L/R OUTS  
PAGE  
3
2. Use the <2> knob to select the MIDI channel number you want your Millennium to receive on.  
3. Use the <4> knob to select the MIDI channel number you want your Millennium to transmit on.  
MIDI Merging  
MIDI merging allows incoming MIDI data to be merged with any MIDI data generated by your Millennium before being sent to the MIDI  
Out/Thru port. Selecting the MIDI Merge option can be accessed in Page 6 of the Utility menu. Once there, the display will look like this:  
ꢀ
ꢀ
SysEx Channel MIDIMerge  
1
2
3
4
1
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
b
L/R OUTS  
OF16  
6
Preset Receive Map  
The Preset mapping features of the Millennium allow you to access any of your Millennium's 200 Presets using the standard 128 Preset Change  
commands through MIDI. From the Factory, the Millennium is set to access User Preset 1 through 100 using MIDI Preset change numbers 1  
through 100. MIDI Preset change numbers 101 through 128 access the Factory Preset bank.  
To gain MIDI access to other presets not mentioned and bypass you must use the preset mapping feature.  
To remap a preset number to a MIDI Preset change number, do the following:  
62  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
1. Press the <Utility> button and scroll to Page 4 of the Utility menu using the <Page> knob. The display reads:  
Prg Rcv Map:MIDI= User  
2
%kHz  
%kHz  
ꢀ%kHz  
msdB  
1
1
msdB 3  
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER6 b  
FACTORY  
BANK  
#
L/R OUTS  
PAGE  
4
OF  
2. Use the <3> knob to select the MIDI Preset change number you want mapped. Note that the number under Millennium USER changes  
along with the MIDI number.  
3. Use the <4> knob to select the Millennium Preset you want the selected MIDI Preset change number to recall. As this number increases  
above Preset 100, note that Millennium USER changes to Millennium FACT, indicating that the mapped number will recall the indicated  
Preset number in the Factory bank..  
Preset Transmit Map  
With the Preset Transmit Map function, you can use your Millennium to send MIDI patch changes of your other effects devices. When you call  
up a preset in your Millennium, the appropriate presets in your other FX unit’s will also be recalled.  
To remap a MIDI Preset change number to a preset number, do the following:  
1. Press the <Utility> button,and scroll to Page 5 of the Utility menu using the <Page> knob. Now use the <1> knob and turn the setting  
to . The display will now appear like this:  
On  
PrgTrans Map:User=MIDI  
2
ꢀ%kHz  
msdB  
On  
1
1
%kHz  
%kHz  
msdB 3  
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
OF  
US1ER6 b  
#
L/R OUTS  
PAGE  
5
2. Use the <3> knob to select the Millennium preset number you want mapped. Note that the number under MIDI changes along with the  
preset number.  
3. Use the <4> knob to select the MIDI preset change number to be sent out the MIDI Out port when the corresponding preset number is  
recalled.  
SysEx Device Channel  
An easy way to think of the System Exclusive Device channel option is to separate System Exclusive data from normal MIDI data. Each type of  
data has its own group of 16 channels upon which data can be transmitted. This feature will also allow individual remote control of more than  
one Millennium with SysEx commands.  
From the Factory and in most situations, the SysEx channel is set at Channel 1.  
63  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
Normal MIDI data such as: Preset Changes, MIDI Volume, Modulation, etc. is transmitted and received on the MIDI channel designated by the  
setting of MIDI RECEIVE CHANNEL ). SysEx data, on the other hand, is transmitted and received on the SysEx channel designated by the setting  
of SYSEX DEVICE CHANNEL.  
This setup frees up your regular MIDI channels for other control options, and gives you the flexibility to request SysEx data from only the  
devices you want in your setup, whether they share the same MIDI channel or not.  
To change the SysEx Device Channel number do the following:  
1. Press the <Utility> button, and scroll to Page 6 of the Utility menu using the <Page> knob. The display reads:  
SysEx Channel MIDI Merge  
2
%kHz  
ꢀ%kHz  
msdB  
1%kHz  
OFF  
msdB 3  
4
msdB  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
US1ER6 b  
#
L/R OUTS  
PAGE  
6
OF  
2. Use the <2> knob to select the desired SysEx channel (1, 2,...15, 16).  
Sysex Dumps  
Preset Dump: Allows you to dump individual Millennium presets to another Millennium or external MIDI devices such as patch librarians,  
computers, or sequencers for backup, storage, or organization. This option allows you to select the preset to be dumped, and, when dumping  
to another Millennium, the preset location where you want the preset dumped.  
To initiate an individual patch dump from the Millennium, do the following:  
1. Press the <Utility> button and scroll to Page 8 of the Utility menu using the <Page> knob. The display reads:  
SysExDump UserPst≥PstNum  
%kHz  
Yeꢀ%kHz  
1%kHz  
msdB 4  
LINK CHANGED LINK CHANGED  
GATE  
1
1
smsdB 2  
msdB 3  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
OF  
US1ER6 b  
#
L/R OUTS  
PAGE  
8
2. Using the function <3> knob, select the Preset number you want to dump. Note that the MIDI number changes as you scroll.  
3. Use the function <4> knob to select the Preset location where you want the preset dumped.  
4. To initiate the dump, turn the function <1> knob. The Information line briefly reads:  
Sending Preset Dump...  
after which it returns to the Preset dump screen.  
Default Dump: Allows you to dump individual Millennium User defaults to another Millennium or external MIDI devices like patch librarians,  
computers, or sequencers for backup, storage, or organization. This option allows you to select the default to be dumped.  
64  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
To initiate an individual Default dump from the Millennium, please perform the following procedure:  
1. Press the <Utility> button and scroll to Page 9 of the Utility menu using the <Page> knob. The display reads:  
UsrDflt:Dual Cho User 1  
%kHz  
%kHz  
msdB 4  
U 1  
LINK CHANGED  
Yeꢀ%kHz  
-
m
-
sd  
-
1
smsdB 2  
B 3  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
FACTORY  
PAGE OF  
BANK 9  
US1ER6 b  
#
2. Using the function <2> knob, select the Effect Module whose Default you want to dump.  
3. Use the function <4> knob to select the User Default you want to dump.  
4. To initiate the dump, turn the function <1> knob. The Information line briefly reads:  
Sending User Default...  
after which it returns to the User default screen.  
Bulk Dump: This option allows you to dump all resident presets in memory to an external recording device, like a patch librarian, computer,  
or sequencer for backup, storage, or organization. This option dumps all presets simultaneously. It does not send any Millennium system  
information, such as SysEx Device channel or Presets maps.  
To perform a SysEx Bulk Dump of all Millennium presets, do the following:  
1. Press the <Utility> button and scroll to Page 7 of the Utility menu using the <Page> knob. The display reads:  
SysEx Dump: Bulk System  
%kHz  
%kHz  
YES  
ꢀ%kHz  
msdB  
ꢀ
2
msdB 3  
msdB 4  
YES  
LINK CHANGED  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
COMP  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
USER  
SEAMLESS  
#
13 b  
L/R OUTS  
PAGE  
7
OF  
2. To initiate a bulk dump, turn the <2> knob. The Information line of the display reads:  
SENDING BULK DUMP...  
after which the display returns to the Dump screen. Bulk Dumps are very large and may take several minutes to complete.  
System Dump: This is the option to use for dumping system data to an external MIDI or SysEx recording device. All the item settings in the  
Utility menu are sent using this option. Presets are not included in this dump.  
The System Dump procedure is the same as the Bulk Dump procedure (see above), except that to initiate a System Dump, turn the <4>  
knob.  
65  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
Other Utility Functions  
The following page, lists some additional Utility functions included in the Millennium that make your programming life a little easier.  
Factory Reset  
Allows you to erase all User Presets, Default and Utility settings at once and restore the Millennium memory to its factory condition.  
WARNING! This procedure will destroy and reset ALL User Presets in the Millennium memory. Be sure you want to erase the memory, and  
start fresh before continuing with this procedure.  
To perform a factory reset, do the following:  
1. Press the <Utility> button and scroll to page 15 of the Utility Menu using the <Page> knob. The display reads:  
Factory Reset ?  
1
%kHz  
%kHz  
Yeꢀ%kHz  
smsdB 2  
msdB 3  
msdB 4  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
LINK CHANGED  
EQ  
GATE  
L/R OUTS  
L/R OUTS  
2
FACTORY  
BANK  
US1ER6 b  
#
PAGE  
15  
OF  
2. To initiate the reset, turn the function <1> knob.  
3. This is your last chance to change your mind. If you are sure, turn the <3> knob. If not, you can abort the procedure by turning the <4>  
knob. If you turn the <3> knob, the Information line of the display briefly reads:  
after which the unit resets, and  
Resetting...  
returns to Preset 1.  
Note: In extreme situations, the Millennium can be completely reset using a special power-up procedure. This will also completely reset the  
Millennium, eliminating any custom settings created by the user. The procedure is as follows:  
1. Press and hold the <Config> button while powering up your Millennium.  
2. Release the <Config> button after an asterisk appears in the information line on the screen.  
3. Press the <Mod> button and the Millennium will re-initialize itself.  
Global vs. Local XLR Cabinet Emulation  
The thing to factor in when using the XLR Cabinet emulator in either global or local mode is whether or not you want all of your sounds  
affected by this change. A good time to use Global mode is when your frequently playing in different venus (because each room always sounds  
different).  
The procedure for selecting either the Local or Global XLR Cabinet emulation is as follows:  
66  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 5 Advanced Topics  
1. Press the <Utility> button and scroll to page 2 of the Utility page using the <Page> knob. The display reads:  
XLR Cabinet  
1
: Local  
%kHz  
ꢀ%kHz  
msdB  
%kHz  
2
msdB 3  
msdB 4  
On  
LINK CHANGED LINK CHANGED  
GATE  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
EQ  
L/R OUTS  
2
FACTORY  
BANK  
US1ER6 b  
#
L/R OUTS  
PAGE  
2
OF  
2. Using the <4> knob, you can turn the Cabinet Emulator to either Local On or Global On mode, or Global Off.  
Output Mode and Speaker Cabinet Voicing Selections  
You can select the output the signal of your Millennium as either a Stereo or Mono signal. Also, depending on the speaker cabinet being used  
(2X12 or 4X12), the Millennium lets you select the optimized voicing for the selected cabinet. The procedure for both selections is as follows:  
1. Press the <Utility> button and scroll to page 1 of the Utility page using the <Page> knob. The display reads:  
Stereo Cab:4x12 Tuner  
%kHz  
%kHz  
2
ꢀ%kHz  
msdB  
2
msdB  
1
2
3
msdB 4  
Off  
LINK CHANGED LINK CHANGED  
GATE  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
EQ  
L/R OUTS  
2
US1ER6 b  
FACTORY  
BANK  
#
PAGE  
L/R OUTS  
1
OF  
2. Using the <1> knob, you can set your Millennium to either a Stereo or Mono output signal. Turning the <3> knob will allow you to  
optimize the Millenniums’ output voicing for either a 2X12 or 4X12 speaker cabinet.  
J-3 Footswitch Set-Up  
The J-3 footswitch offers three footswitches that can be assigned to perform numerous different functions. Out of the box, the J-3 will change  
presets up and down and will A-B channel switch. Changing these footswitch functions is done on pages 13 and 14 of the Utility menu.  
To access this assignment function, press the <Utility> button and turn the <Page> knob to page 14.  
Page 14 of the utility menu gives you the following foot switch assignment options: Preset Up, Preset Down, Song List Up, Song List Down,  
Channel A-B switching, Tuner Access, TapIt tap tempo switch and FX bypass. These selections can be made by using either the <2>, <3> or  
<4> knobs.  
Page 15 of the Utility menu lets you program a Song list so you can build a list of up to 32 different Presets to use that can be accessed by  
pressing 1 footswitch. To set the Song list use the <3> knob to select the step and the <4> knob is used to select which preset will be used  
with the selected step.  
67  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
Section-6 The J-12 Foot Controller  
Configuring the Pedalboard  
The optional Johnson Amplification J-12 foot controller can help you get the most out of your Millennium. Since the J-12 talks to the  
Millennium using a proprietary communication protocol, it offers better response time and capabilities not available with convention MIDI  
pedalboard controllers.  
The J-12 includes 12 footswitches for preset and parameter control. It also features 2 built-in Expression Pedals. The large 20 character display  
constantly feeds you important information such as Preset names, CC links and Tuner indicators.  
Note: All Pedalboard functions involved in the next section also apply to the Digitech Control One Foot Controller  
Connecting the Johnson Amplification J-12 Foot Controller  
The J-12 uses a standard 5-pin DIN cable (like those used for MIDI) to communicate with the Millennium. Simply connect the J-12 output jack  
to the Millennium Input jack (when the unit is powered down) and you’re ready to roll!  
NOTE: Never plug anything other than the J-12 into the Millennium's Foot Controller input jack. (Voltage is present at this jack).  
Expression Pedal Names  
With the Millennium being able to accommodate up to 4 Expression pedals, the pedal names change if the J-12 is used. The Names are as  
follows:  
Exp1 = Expression pedal 1 input on the rear of Millennium, when the J-12 is not connected.  
Exp2 = Expression pedal 2 input on the rear of the Millennium, when the J-12 is not connected.  
Exp1 = Expression pedal 1 on the J-12 (When the J-12 is connected).  
Exp2 = Expression pedal 2 on the J-12 (When the J-12 is Connected).  
Exp3 = Expression pedal 1 input on the rear of Millennium, when the J-12 is connected.  
Exp4 = Expression pedal 2 input on the rear of the Millennium, when the J-12 is connected.  
68  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
Assigning Functions  
The J -12 helps you organize your sounds into 19 groups called Banks. Each of these Banks utilize the 10 footswitches patches, which are user  
programmable to do one of several functions. These functions include:  
• Selecting any Millennium Preset  
• Modifying or turning On/Off any Parameter in real-time  
• Sending MIDI CC information out of the MIDI out port (Toggle CC# for values 0 or 127)  
• Assign a MIDI CC# for the Expression pedal to send out the MIDI port  
To change Banks, Press either the Bank Up or Bank Down footswitches on the J-12 to take you up or down one bank at a time.  
The Foot Controller setup menu contains all the setup options necessary to use the Millennium with the optional J-12 foot controller. The  
submenus included under the Foot Controller setup are located on pages 10, 11 and 12 of the Utility menu and they include:  
• Patch Assignment  
• Continuous Control  
Assigning Presets to Footswitches  
To assign any currently selected Preset to a patch footswitch in the currently selected bank, do the following:  
1. Once the selected Preset has been chosen, press the <Assign> button once. The display reads:  
ꢀ
ꢀ
Select a J-12 F.Switch  
1
2
3
4
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK1  
USER  
#
DIGITAL  
CLIP  
b
L/R OUTS  
2. Press one of the ten footswitches to Link the selected preset to that switch. If you choose a footswitch that is already assigned to do  
something else besides select a preset, the display reads:  
ꢀ
ꢀ
Re-Assign F.Switch ?  
1
2
3
4
YES  
no  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
BANK1 11  
USER  
#
DIGITAL  
CLIP  
b
3. Turning the <3> function button re-assigns the function of the footswitch while turning <4> will leave everything as it was, aborting the  
procedure.  
Once you link a Preset to a Patch in a Bank, the LED lights above the footswitch that you selected indicating the Link was successful.  
4. Press the <Preset> button to exit.  
69  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
Assigning Parameters to Footswitches/ Expression Pedals  
The Millennium allows you to control up to 16 Parameters per Preset. Each time you link a parameter to a Footswitch or expression pedal, it is  
added to any assignments already made to that controller. This is where the Millennium becomes the dedicated work horse that it is, by doing  
all of the organizing for you so all you have to do is select which parameter is being controlled, then tell the Millennium to “Make it so”.  
To assign any currently selected Parameter to a footswitch or Expression pedal in the  
currently selected bank, do the following:  
1. Be sure that the parameter you want to link is displayed and selected (below, is an example the Channel A gain setting) Turning the <1>  
knob make the Gain in Channel A active for linking. The display should appear something like this:  
ꢀ
ꢀ
a: gain lvl B:Gain LVL  
1
%
40  
100  
70 10ꢀ  
0%  
2
3
4
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
PAGE  
USER  
#
DIGITAL  
CLIP  
b
L/R OUTS  
2
OF  
5
2. Turn the <4> knob to select the gain parameter, then press the <Assign> button once. The display reads:  
ꢀ
ꢀ
Gain Exp 1 Min[ 56]Max  
1
2
3
4
On  
Pdl  
0
ꢀ100  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
U1SE9R b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE  
1
OF  
3. Select the footswitch or move the expression pedal to be used. An example would be to use Exp 1. From there, use knobs <3> and <4>  
to set the minimum and maximum ranges of the gain. Minimum and maximum settings can also be set in reverse. An example would be if  
you set the Gain Min and Max levels in reverse so when the Expression Pedal is moved forward, it would lower the Gain setting.  
Once this is done the display will appear something like this:  
ꢀ
ꢀ
Gain Exp 2 Min[ 69]Max  
1
2
3
4
On  
Pdl  
20  
55  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
LINK CHANGED  
EQ  
GATE  
L/R OUTS  
2
US1ER9b  
FACTORY  
BANK1  
#
DIGITAL  
CLIP  
L/R OUTS  
OF  
4. To exit the parameter assignment mode press the <Preset> button to return to Preset mode. The <Store> button will stay bright until  
these changes are stored, or the preset is changed.  
70  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
Other Footswitch Functions  
The footswitches on the J-12 can be assigned to do several functions. This is done through the Foot Controller menus in the Utility section of  
the Millennium. These functions include:  
Toggle MIDI CC: This function allows you to send MIDI Continuous Controller (CC) information out the MIDI port while the footswitch  
still maintains its ability to control a parameter directly. When assigned to a footswitch, CC values 0 or 127 are sent. CC numbers 0 through  
127 are available.  
Exp CC send: The Expression pedals of the J-12 can also send MIDI CC data to other MIDI devices.  
The procedure for setting up a MIDI CC toggle footswitch function is as follows:  
1. Press the <Utility> button once. The display appears something like this:  
ꢀ
ꢀ
Stereo Cab:4X12 Tuner  
1
2
3
4
2ꢀ  
ꢀ
2
Off  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER6 b  
FACTORY  
#
DIGITAL  
CLIP  
PAGE  
1
OF  
2. Turn the <Page> knob to until you reach page 10 and the display reads:  
ꢀ
ꢀ
J12FC:Bank FS=Pst CCTran  
1
2
3
4
1
ꢀ
1
---  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE10OF  
3. Turn the <2> knob to select the bank in which the CC toggle is to used. Once the bank is selected, use the <3> knob to select the  
footswitch to be used. The display reads:  
ꢀ
ꢀ
J12FC:Bank FS=Tog CCTran  
1
2
3
4
ꢀ
1
6
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6 b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE 10OF  
4. The display now shows that footswitch 6 in bank 1 is set to toggle CCs. Take notice that (from the factory) when footswitches 6-0 are  
selected, you can assign that footswitch a CC number from 0-127 by turning the <4> knob.  
71  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
5. Now to assign the CC number, just turn the <4> knob until you have reached the desired CC. The display will now read something like  
this:  
ꢀ
ꢀ
J12 FC:Bank FS=Tog CCTran  
1
2
3
4
ꢀ
6
127  
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE10OF  
6. Press the <Preset> button to exit the Foot controller setup menu.  
Assigning MIDI Control to the Expression Pedals  
This series of menus and submenus allows MIDI setup of the Expression pedals of the J-12. There are two procedures you must do in order for  
the Expression pedals to work properly with MIDI:  
1. Assign CC Number  
2. CC Transmit Channel  
Assign CC Number to Expression Pedals - This option allows you to choose the MIDI CC numbers you want to use for sending  
continuous control messages using any one of the 4 expression pedal options. These assignments can be done on pages 11 and 12 of the  
Utility menu. From the Factory, the expression pedal(s) are not pre-assigned to any MIDI CC number. To assign which CC number is sent  
from the expression pedal(s), do the following.  
1. Press the <Utility> button once. The display appears something like this:  
ꢀ
ꢀ
Stereo Cab: 4x12 Tuner  
1
2
3
4
2
2
Off  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE  
1
OF  
2. Turn the <Page> knob until you reach page 11 and the display will appear something like this:  
ꢀ
ꢀ
CCSnd: Exp1 Exp2  
1
2
3
4
LINK CHANGED  
OFF  
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
PAGE11OF  
72  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
3. Turn either function keys <2 or 3> to assign a CC number to the selected expression pedal . The display will appear like this on page 11 if,  
for example Exp 1 is selected. (Exp1=Internal Expression pedal 1 insert on Millennium w/o the J-12. Or, expression pedals 1 or 2 on the J-  
12 when connected. The display now reads:  
ꢀ
ꢀ
CCsnd:Exp1 Exp2  
1
2
3
4
30  
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
PAGE11OF  
Page 12 will appear like this:  
ꢀ
ꢀ
CCsnd: Exp3 Exp4  
1
2
3
OFF  
OFF  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
L/R OUTS  
2
FACTORY  
US1ER6b  
#
DIGITAL  
CLIP  
PAGE12OF  
4. Press the <Utility> button to exit.  
For a complete explanation of expression pedal names, please refer to page 68.  
CC Transmit Channel - This option allows you to set the MIDI channel on which CCs will be sent out the Millennium MIDI Out port to  
other MIDI devices. If you are using the J-12 for the Millennium only, you don't need to worry about setting up this option.  
However, if you plan to use the J-12 for continuous control over other MIDI devices (either in conjunction with the Millennium or by  
themselves), you need to assign a MIDI transmit channel for each of the CC numbers you'll be using for continuous control of the other  
devices.  
To change the MIDI channels on which the selected CCs will transmit to other MIDI devices, do the following:  
1. Press the <Utility> button once. The and the display should appear something like this:  
ꢀ
ꢀ
Stereo Cab:4x12 Tuner  
1
2
3
4
2
ꢀ
2
Off  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER6 b  
FACTORY  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE  
1
OF  
73  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
2. Turn <Page> knob to page 3 and the display will read:  
ꢀ
ꢀ
MIDI: RcvChnl TransChnl  
1
2
3
4
ꢀ
1
1
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6 b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE  
3
OF  
3. Turn the function knob <4> to select the MIDI CC transmit channel. For example, select channel 10 and the display will now appear like  
this:  
ꢀ
ꢀ
MIDI: RcvChnl TransChnl  
1
2
3
4
ꢀ
1
10  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER6 b  
FACTORY  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE  
3
OF  
4. To exit the Transmit channel assignment, press the <Preset> button.  
Momentary Footswitch Assignment  
The Millennium now has the ability to assign any footswitch of either the J-12 or Digitech Control One foot controllers to act as momentary  
switches. This will give you the ability to toggle the value a parameter by a press /hold and release of the selected footswitch. The momentary  
footswitch assignment can be done by performing the following procedure:  
1. When the parameter for assignment has been selected, press the <Assign> button once. After you have selected the footswitch for  
assignment, the display will appear something like this:  
Fx:lvl FS # Min[ 96] Max  
3
1
2
4
Off 100  
Ont  
F6  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
US1ER9 b  
#
DIGITAL  
BANK  
PAGE  
6
OF  
2. Now turn the <1> button to set the footswitch to either: Ont(On Toggle) or OnP(On Momentary).  
3. Choosing the OnP setting will make the footswitch perform as a momentary footswitch. This means that the footswitch will toggle  
the selected parameter while pressed, and once released, the parameter will return to its original value.  
74  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
Other Pedalboard Tidbits  
Here are a few other features that you will want to learn about to get the most out of your J-12 foot controller:  
Bank Up/ Tuner and Bank Down / Bypass Footswitches  
These two foot switches are located at top right side of the J-12. The Bank Up/Tuner footswitch, as you may have guessed, will move to the  
next Bank Up in the Millennium, as well as access the Tuner Mode by simply pressing and holding the footswitch until the Tuner appears in  
the display.  
To access the next bank down press the Bank Down footswitch once. To bypass the Digital effects in the Millennium, press and hold the  
footswitch until the LEDs indicate that the unit is now in effect bypass mode.  
Using the Tuner  
1.To access the Tuner mode using the optional J-12 foot controller, press and hold the <Bank Up/Tuner> footswitch to engage tuner  
mode.  
2. As you play a note on the guitar, the indicator in the display of the J-12 will move either to the right, or the left. If the indicator is moving  
right, the note you are playing is sharp. If the indicator moves left, you are flat. The goal is to tune your guitar so that the indicator stops  
in the middle and the display locks-in, indicating you are in tune.  
3. In both methods of tuning, the tuner is referenced to A=440Hz. If you prefer tuning sharp or flat according to the A reference, use the  
<3> knob to select a new reference. This can be set as high as A=453Hz or as low as A=427Hz. The tuner can also be used for alternate  
tuning references where A=Ab (meaning you play an A note, but you hear an Ab note). It is possible to tune as low as A=Gb.  
4. At this point, press any footswitch on the J-12 to exit the Tuner mode.  
Naming Banks  
Straight out of the box, the Millennium has 19 user Banks to choose from when used with the either the J-12 foot controller. Each of the  
Banks have been given a specific named to give indication to what type of presets exist with the Bank. In your constant editing mode to make  
the box custom to your needs, we have given you the ability to rename the Banks. The procedure is as follows (and please don’t worry, we  
won’t be hurt):  
1. From Preset mode press the <Utility> button and the display will appear something like this:  
2. Turn the <Page> knob until you reach page 13 and appears like this:  
ꢀ
ꢀ
Bank: Top 5  
2
Name?  
4
1
3
ꢀ
1
Yes  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
LINK CHANGED  
EQ  
L/R OUTS  
2
FACTORY  
US1ER6 b  
#
DIGITAL  
CLIP  
L/R OUTS  
PAGE13OF  
75  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 6 The J-12 Foot Controller  
3. At this point, use the <2> knob to select the Bank to be named. Once the Bank has been selected, turn the <4> knob to rename the  
Bank. The display now appears like this:  
ꢀ
ꢀ
Name:Top 5  
1
2
3
4
COP  
LINK CHANGED  
CAP  
n
ꢀ
br  
Ins  
LINK CHANGED  
LINK CHANGED  
WAH TUBE  
LINK CHANGED  
GATE  
EQ  
L/R OUTS  
2
FACTORY  
USER  
#
DIGITAL  
CLIP  
b
L/R OUTS  
4. To exit the naming bank assignment, press the <Utility> button.  
5. Using the <1> knob, change the character to the one you want in the selected position.  
6. When the correct character is displayed in that position, use the <Page> knob to scroll the cursor to the next character you want to  
change.  
7. Use the <2> knob to select numbers, the <3> knob to insert spaces and the <4> knob to copy and paste characters.  
8. To copy a character, position the cursor under the character you want to copy (using the <Page> knob), then turn the <4> knob  
clockwise. To paste the copied character, position the cursor where you want to paste the character, then turn the <4> knob counter-  
clockwise.  
9. To abort the procedure, push either the <Preset> button to take you to Preset Mode, the <Edit> button to take you to FX Edit Mode, or  
the <Utility> button to take you to Utility mode, depending upon which mode you want to enter.  
Un-Linking or Viewing Parameter Control  
1. To un-link or view a parameter that has been assigned to a footswitch, Expression Pedal or LFO simply press the <Assign> button twice  
The display will tell you which parameter is linked to which footswitch. To unlink, simply turn the <1> knob and the top line of the display  
will now read:  
Available Link  
2. To see any other parameter links in the selected program, press the <Assign> button twice and then turn the <Page> knob.  
76  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Section-7 Appendix  
Millennium Factory Preset List  
28- Marshall JCM 800 Combo  
29- Marshall JCM 800 Stack  
30- A)Clean B)HotRod Marshall  
Cfg-1  
Cfg-4  
Cfg-4  
Bank 1 Top 5  
1- Rectifier Solo  
Cfg-4  
Cfg-4  
Cfg-3  
Cfg-1  
Cfg-4  
2- Panning Twin Reverb  
3- Matchless Blues  
4- Custom Marshall w/Reverb  
5- Get Your Wah Wahs Out  
Bank - 7 Johnson  
31- Johnson Fat Soul  
32- Johnson Powr-Solo  
33- Johnson Edge->Clean  
34- Johnson Tone&Clean  
35- Johnson Gain&Mo gain  
Cfg-3  
Cfg-4  
Cfg-9  
Cfg-9  
Cfg-9  
Bank 2 Fender  
6- ‘65 Black Face Twin  
7- ‘65 Twin Bright  
8- Fender Overdrive  
9- Leslie Jazz twin  
Cfg-4  
Cfg-4  
Cfg-4  
Cfg-4  
Cfg-4  
Bank - 8 Signature 1  
36- Mysterious Wah  
37- Stray Dead Catz  
38- Smashing Bumpkins  
39- Pride Delay  
Cfg-13  
Cfg-9  
Cfg-4  
Cfg-4  
Cfg-4  
10-Fender Phase/Pong Delay  
Bank 3 Boogie/Soldano  
11- Boogie Mark II Combo  
12- Rectifier Stack  
13- Trem-O-Verb  
14- Boogie Mark II Stack  
15- Soldano SLO  
Cfg-4  
Cfg-4  
Cfg-4  
Cfg-4  
Cfg-4  
40- Dick Dale  
Bank - 9 Signature 2  
41- Classic SRV  
42- Brown Sound  
43- E.Johnson Clean/Solo  
44- Foxy Lady  
45- Run Like Gilmour  
Cfg-4  
Cfg-9  
Cfg-9  
Cfg-4  
Cfg-4  
Bank 4 Vox  
16-’63 Vox AC 30 Top Boost  
17- Vox AC 30 Clean/Dirty  
18- Vox w/Analog Delay  
19- AC 30 Chorus/Delay  
20- Vox AC 30 Cln/Drty Combo  
Cfg-1  
Cfg-1  
Cfg-1  
Cfg-4  
Cfg-4  
Bank 10 Blues  
46- Bluesy Twin Solo  
47- Tremolo Blues  
48- Blues Boogie  
49- Blue BB'S  
Cfg-9  
Cfg-9  
Cfg-9  
Cfg-9  
Cfg-2  
Bank 5 Matchless  
21- Matchless DC30 Combo  
22- Matchless w/Reverb  
23- DC30 Leslified  
24- Matchless Gain Solo  
25- Mtchles Cln/Edge  
Cfg-1  
Cfg-4  
Cfg-4  
Cfg-12  
Cfg-9  
50- Slide Blues  
Bank 11 Dual Tone  
51- L)Vox R)Marshall  
52- Twin->Matchless Heaven  
53- L)Metal Tube R)Fuzz  
54- Twin/Match Hybrid ExpPdl  
55- Twin->Marshall Solo  
Cfg-6  
Cfg-4  
Cfg-6  
Cfg-4  
Cfg-6  
Bank 6 Marshall  
26- Hot Rodded Marshall  
27- Marshall Master Volume  
Cfg-4  
Cfg-1  
77  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Bank 12 Alternative  
56- Industrialized  
57- Whammy Madness  
58- Triplet Delay  
59- Post-Seattle Grind  
60- Space Hippie  
Bank 18 Dynamics  
86- Ducked Delay Solo  
87- Dynamic Chorus  
88- Automatic Wah  
89- Guitar Synth  
90- Dynamic Tremolo  
Cfg-9  
Cfg-2  
Cfg-4  
Cfg-4  
Cfg-8  
Cfg-1  
Cfg-4  
Cfg-1  
Cfg-7  
Cfg-4  
Bank 13 Country  
61- Pedal Steel  
62- Rockin’ Billy  
63- Good For Pickin’  
64- Drinking w/Cowboyz  
65- Stereo Slapback  
Bank 19 Morph  
91- Clean->->Solo Morph  
92- Tube->->SpaceFuzz Morph  
93- Auto Morph  
94- Soldano Ambient Morph  
95- 2 Second Loop Jam  
96- Wahs Happening?  
97- Planet Diablo  
Cfg-2  
Cfg-4  
Cfg-4  
Cfg-7  
Cfg-13  
Cfg-15  
Cfg-9  
Cfg-15  
Cfg-4  
Cfg-9  
Cfg-15  
Cfg-8  
Cfg-2  
Cfg-3  
Cfg-3  
Bank 14 Vintage  
66- Surfari  
67- Fuzz in the Sky  
68- Danno Electro  
69- Electric Sitar  
70- Guitar Organ  
Cfg-4  
Cfg-4  
Cfg-9  
Cfg-9  
Cfg-4  
98- Blues in D  
99- JC-120 Jazz Chorus  
100-Sweet Combo  
Bank - 15 Studio  
71- Chorus Wash  
72- Vol Pedal Swell  
Cfg-10  
Cfg-8  
73- Cln Comp Mono>Ster  
74- PWR CORD Mono>Ster  
75- Greasy Solo  
Cfg-13  
Cfg-13  
Cfg-10  
Bank - 16 Jazz/Fusion  
76- MD’s Sweet Solo  
77- Pop Jazz Comp  
78- Mainstream Jazz  
79- Fusion Solo Boogie  
80- Steely Phaser  
Cfg-9  
Cfg-10  
Cfg-9  
Cfg-10  
Cfg-9  
Bank - 17 Rock  
81- Stack In a Studio  
82- Metallurgist  
83- Phasey Rhythm  
84- Too Heavy  
Cfg-1  
Cfg-4  
Cfg-4  
Cfg-4  
Cfg-13  
85- Just A Wah  
78  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Millennium Preset Descriptions  
To help all of you Tone and Effect connoisseurs along the way, this list gives you a brief description all 100 Factory presets of the Millennium.  
Bank - 1 Top 5  
1- Rectifier Stack - Pure and rich Dual Rectifier Stack tone with Dual Delay and Chorus modules which make it ideal for soloing.  
2- Panning Twin Reverb - Tone of the legendary Twin with Reverb and an Auto Panner effect to that pans the signal right and left.  
3- Matchless Blues - The mighty DC-30 is overdriven and uses a flanger which makes it ideal for playing the blues.  
4- Custom Marshall w/Reverb - The great Marshall with the custom “Mods” already in place and just a touch of reverb.  
5- Get Your Wah Wahs Out - A Boogie MK II Amp model that uses the Analog Wah module with Delay and Reverb.  
Bank - 2 Fender  
6- ’65 Black Face Twin - This rare (and high priced) amp tone is brought out in the Millennium.  
7- ’65 Twin Bright - Boosted Mids and Highs will let this Twin cut through in any room.  
8- Fender Overdrive - Classic Twin tone, with just a touch a distortion to overdrive the front end.  
9- Leslie Jazz Twin - Let the Jazz shine through with the Leslie to fill up this Twin.  
10- Fender Phase/Pong Delay - The Twin amp tone with Phaser and Pong Delay.  
Bank - 3 Boogie/Soldano  
11- Boogie Mark II Combo - The Combo Amp tone of Carlos .  
12-Rectifier Stack - The full wall of Dual Rectified Tone is present here.  
13- Trem-O-Verb - Dual Rectifier tone with a Tremolo effect at your disposal.  
14- Boogie MK II Stack- The legendary vintage tone that Mr. Randall Smith created in a shed almost thirty years ago.  
15- Soldano SLO - The high-priced prestiges tone of what is sure to become a amplifier classic.  
79  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Bank - 4 Vox  
16- ‘63 Vox AC 30 Top Boost - Vintage British Combo tone with Reverb mixed in for good measure.  
17- Vox AC 30 Clean/Dirty - Classic clean AC 30 in channel A and distortion in channel B.  
18- Vox w/Analog Wah - A slightly overdriven AC 30 with an Analog tape delay effect.  
19- AC 30 Chorus/Delay - AC 30 tone with lush Chorus and a 500ms Delay.  
20-Vox AC30 Cln/Drty Combo - Channel switching from a clean to overdriven AC 30 Amp.  
Bank - 5 Matchless  
21- Matchless DC 30 Combo - The tone of the of the new Industry-standard work horse.  
22- Matchless HC 30 - Matchless half-stack tone that can kick in distortion to overdrive the amp by channel switching.  
23- DC30 Leslified - The DC 30 with leslie simulation thrown in to keep things spinning.  
24- Matchless DC 30 Solo - A soloing must with overdriven Matchless tone with Detuning and Delay digital effects.  
25- Matchless Cln/Edge- Morph between the great tones of a Matchless and a hot-rodded Marshall Master.  
Bank - 6 Marshall  
26- Hot Rodded Marshall - Marshall tone with all of the modifications already done to it with Dual detuner and Reverb digital effects.  
27- Marshall Master Volume - A simple mid ‘70s Marshall Master Volume that was designed to rock with all tone controls pushed to 10.  
28- Marshall JCM 800 Combo - The big Marshall tone harnessed in a 2X12 combo.  
29- Marshall JCM 800 Stack - The amplifier that revolutionized the 1980s Rock Sound.  
30- Clean/Hot Rod Marshall - A Johnson Amp model that allows you to produce pristine clean and distorted tones at the same time.  
Bank - 7 Johnson 1  
31- Johnson Fat Soul - Tube Distortion with Dual Delay and Stereo Reverb effect modules.  
32- Johnson Powr-Solo - Big, custom tube distortion with Dual Detuning and Dual Delay that can be thrown in any solo situation.  
80  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
33- Jonson Edge->Clean - A overdriven Amp tone that can be switched to to clean with a digital Compressor, Dual Delay and Stereo reverb  
digital effect modules.  
34- Johnson Tone and Clean- A custom Johnson Amplifier module that boosts the clean signal with 6-band Parametric EQ and adds a Dual  
Phaser and Stereo dual delay module.  
35- Johnson Gain&Mo Gain- A Johnson custom amplifier module that boosts the signal by using a parametric 6-band EQ. And it also uses  
Stereo Tremolo and Stereo Reverb Effects.  
Bank - 8 Signature 1  
36- Mysterious Wahs - A dynamic modifier is connected to the Analog Wah module to help give you the sound of the Irish “Pop” guitarist.  
37- Stray Dead Catz - Vintage Fender Twin with delay is used to produce the classic Setzer tone .  
38- Smashing Bumpkins - A Dual rectifier is used to re-create the tone of Mr. Corgan and friends.  
39- Pride Delay - A Vox AC 30 model with lots of Delay, just the way the Mr. Edge likes it.  
40- Dick Dale - The legendary tone of the man that gave birth to surf music rings out in a ‘65 Black Face model with Reverb.  
Bank - 9 Signature 2  
41- Classic SRV - The classic tone of the legendary Stevie Ray Vaughan which utilizes a custom Jonson Amplifier model and a Rotary Speaker  
simulator that can be turned on to produce a Leslie effect with an additional Reverb module.  
42- Brown Sound - Tone of the great Mr. Van Halens’ early years when the trusty Marshall stood by his side.  
43- E. Johnson Clean/Solo - The violin tone of Austin, Texas, complete with Chorus, Delay and Reverb digital effects.  
44- Foxy Lady - Pick up your Strat and let the feedback wake the neighbors with this Marshall model run all of the way up.  
45- Run Like Gilmour - This preset is great to be used on any classic of Pink Floyd tunes.  
Bank - 10 Blues  
46- Bluesy Twin Solo- This ‘65 Black face model with compressor and Delay will touch anyone with your blues.  
47- Tremolo Blue- The great tremolo sound is present in this preset along with a Fender Twin amp model.  
48- Blues Boogie - the Boogie MK II combo Amp model that was designed to be at home in any blues club.  
81  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
49- Blue BB’s- Added parametric EQ with reverb and Delay give you the tone of BB'S and his best girl Lucille.  
50- Slide Blues- Use an expression pedal on this preset to create bayou-type slide guitar effects.  
Bank - 11 Dual Tone  
51- L) Vox R)Marshall - This preset combines an AC 30 and Marshall amp model to give you the best of both worlds.  
52- Twin/Matchless Heaven - Most could not afford to own both of these tones, but now you have both side by side at the same time.  
53- L) Metal Tube R)Fuzz - Combine both of these distortions, and you will have all of the gain and fuzz in the world at your fingertips.  
54- Twin/Match Hybrid ExpPdl - Use an expression pedal to morph between Fender Twin and Matchless amp models .  
55- Twin->Marshall Solo - Use the Twin model with reverb for rhythm tone then morph to the Marshall model for the big solo.  
Bank - 12 Alternative  
56- Industrialized - The Soldano SLO model is used with the a Dual Detuner to produce a unique distortion tone.  
57- Whammy Madness - Get yourself an expression pedal to produce whammy effects through the Rectifier model.  
58- Triplet Delay - This Boogie MK II model with tons of Delay and Reverb can be used to create beautiful clean tones.  
59- Post-Seattle Grind -This preset combines Vox and Marshall tones to produce a nice slight distortion tone.  
60- Space Hippie - The Vox AC 30 Top Boost is used with Dual Chorus, Dual Delay and Dual Phaser modules to produce sounds that are out  
of this world.  
Bank - 13 Country  
61- Pedal Steel - Use an expression pedal on this one to produce pedal steel-type effects.  
62- Rockin’ Billy - This preset is a must for any rock-a-billy tune.  
63- Good For Pickin’ - This ‘65 Blackface Fender tone with Reverb and slapback delay will make you “a grinnin”.  
64- Drinking w/Cowboyz - Try this preset when the no good, drinkin’, dog-stealin’, wrecked your truck person in your life leaves ya.  
65- Stereo Slapback - A distorted Fender with compression and Analog and Dual Delay preset can be heard here.  
82  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Bank - 14 Vintage  
66- Surfari - Great surf music tones will shoot the pipeline with this Tremolo and Reverb preset.  
67- Fuzz in the Sky - Use this preset to bring out the great fuzz tone of the ‘60s and ‘70s.  
68- Danno Electro - Pitch shifting and Dual Chorus is used to help produce this Baritone guitar preset.  
69- Electric Sitar - Use this Dual Pitch Shifter preset to create Shenkar-type sounds.  
70- Guitar Organ - Great Leslie effects can be heard on this preset that uses a Rotary Speaker Simulator module.  
Bank - 15 Studio  
71- Chorus Wash - Heavy Chorus effects and Dual amplifier types are used in this preset.  
72- Vol Pedal Swell - Use this preset to create Synth-like vol pedal swells.  
73- Cln Comp Mono->Ster - This straight ahead clean tone with compressor can go from a mono to stereo output with an expression pedal.  
74- PWR CORD Mono>Ster - Take this great power rhythm tone from mono to stereo with the use of an expression pedal.  
75- Greasy Solo - Use this Preset for recording any guitar solo in the studio.  
Bank - 16 Jazz/Fusion  
76- MD’s Sweet Solo - The tone of a studio legend that is great for the Fusion solo.  
77- Pop Jazz Comp - Use this preset for Wes Montgomery-type sounds.  
78- Mainstream Jazz - This is a great tone to use that utilizes a Fender twin amp module with EQ, Chorus and Reverb effects.  
79- Fusion Solo Boogie - A great Boogie tone preset for fusion solos.  
80- Steely Phaser - A Twin Reverb model with Dual Phaser and Auto panning effects for fusion rhythms.  
Bank - 17 Rock  
81- Stack in a Studio - Get the big Marshall tone with this preset that is guaranteed to rock any one’s world.  
82- Metallurgist - Bring on the Dual rectifier stack sound with Dual flanger and Delay.  
83  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
83- Phasey Rhythm - Use this Dual-tone Phaser effected preset for rhythm playing.  
84- Too Heavy - You will have gain for days when you use this Dual Rectifier model preset.  
85- Just a Wah - This JCM 800 Combo amp with distortion uses an Analog Wah module to produce overdrive tones.  
Bank - 18 Dynamics  
86- Ducked Delay Solo - A Dynamic modifier is used in this preset so the harder your attack is, the more delay will be heard.  
87- Dynamic Chorus - This is a beautiful clean chorus preset that has a dynamic modifier assigned to the chorus module. This means, harder  
attack equals more chorus.  
88- Automatic Wah - Use this overdriven preset with dynamic attack that will produce an auto wah effect.  
89- Guitar Synth - Use this preset to produce guitar synth effects, that change depending on how hard your attack hits.  
90- Dynamic Tremolo - Change your Tremolo speed by attacking the strings harder on this preset.  
Bank - 19 Morph  
91- Clean->->Solo Morph - Use this preset when you need to morph from a clean tone preset to a distorted solo tone.  
92- Tube->->Space Fuzz Morph - You can morph from a Tube distortion to a classic Fuzz distortion.  
93- Auto Morph - Use this preset when you want the Millennium to automatically morph from a clean to distorted tone.  
94- Soldano->->Ambient Morph - This preset is used to morph from a clean Fender Twin to a Soldano amp model.  
95- 2 Second Jam Loop - This preset is great to use when you want to play along with a sample, because the 2 second delay will automatically  
loop itself to act as a sample so you can jam along with yourself.  
96- Wahs Happening - Get out of this world sounds with this Matchless model that uses Auto Wah, Pitching, Delay and Chorus effects.  
97- Planet Diablo - This Twin Reverb is heavily effected with Delay, Chorus and Reverb.  
98-Blues in D- Use this preset to create the great blues tone (with pitch shifting),you never thought possible.  
99- JC-120 Jazz Chorus- Use this preset to get the industry-standard sound of a lush Jazz Chorus 120.  
100- Sweet Combo - This is the combo amplifier tone personified.  
84  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Effect Configuration Chart  
Config:MonoSplit 2,2  
Config:Series Full  
Config:Stereo 4,4,2  
11  
12  
13  
1
6
GATE  
L/R OUTS  
GATE  
GATE  
4
4
L/R OUTS  
L/R OUTS  
F
2
2
2
L/R OUTS  
L/R OUTS  
Config:Series 2,4,4  
Config:Mono Split 4,4,2  
Config:Series 3,4  
7
2
GATE  
GATE  
L/R OUTS  
L/R OUTS  
GATE  
4
2
4
L/R OUTS  
L/R OUTS  
3
4
2
4
4
L/R OUTS  
L/R OUTS  
Config:Series 4,4,4,4  
Config:Series 4,3  
Config:Series 4,2,4  
3
8
GATE  
GATE  
L/R OUTS  
L/R OUTS  
GATE  
4
4
4
4
3
L/R OUTS  
4
4
2
4
L/R OUTS  
Config:Stereo 4,4,4,4  
Config:Series 2,2  
Config:Series 4,4,2  
9
14  
15  
4
5
GATE  
GATE  
GATE  
L/R OUTS  
L/R OUTS  
L/R OUTS  
4
4
4
4
2
2
4
4
2
L/R OUTS  
Config:Parall 4,4,2  
Config:Stereo 2,2  
Config:MonoSplit 4,4,4,4  
10  
GATE  
L/R OUTS  
GATE  
4
2
4
GATE  
L/R OUTS  
L/R OUTS  
4
4
2
2
4
4
L/R OUTS  
Dual Output Comfigurations -Take notice that several effect configurations (ie: 12 and 14) use dual outputs. This indicates that Dual distortion  
paths can be run to both the right and the left outputs. This will be dictated by panning either distortions to the right or the left.  
Key: 4= 1/4 size module  
3= 3/4 size module  
K
2= 1/2 size module  
KF= Whole size module  
85  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Harmony Interval Charts  
Interval  
üOct  
ü7th  
ü6th  
ü5th  
ü4th  
ü3rd  
ü2nd  
Ref  
Major  
Minor  
Harm.Minor Mel.Minor  
Dorian  
C
Mixolydian  
Lydian  
C
C
C
B
C
B
C
B b  
A
C
B
B
B b  
A b  
G
B b  
A
A
A b  
G
A
A
G
F
G
G
G
G
F#  
E
F
F
F
F
F
E
E b  
D
E b  
D
E b  
D
E b  
D
E
D
D
D
C
B
C
C
C
C
C
C
¨2nd  
¨3rd  
¨4th  
¨5th  
¨6th  
¨7th  
¨Oct  
B
B b  
A b  
G
B
B
B b  
A
B b  
A
A
A b  
G
A
A
G
F
G
G
G
G
F#  
E
F
F
F
F
F
E
E b  
D
E b  
D
E b  
D
E b  
D
E
D
D
D
C
C
C
C
C
C
C
Lydian  
Aug.  
Minor  
Pent.  
Whole  
Tone  
Hlf-Whl  
Dim.  
Whl-Hlf  
Dim.  
Major  
Pent.  
Int.  
Int.  
Int.  
Int.  
Blues  
Int.  
Int.  
Int.  
C
C
B
üOct  
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
üOct  
üı7th  
ü6th  
ü5th  
C
B
B b  
A
üOct  
ü7th  
ü6th  
ü6th  
ꢀ
ꢀ
ꢀ
ꢀ
C
C
A
ꢀ
üOct  
ü5th  
ꢀ
üOct  
üı7th  
A
C
A
C
B büı7th A#  
G
G#  
F#  
üOct  
üOct  
üı6th  
üı5th  
B b  
G#  
F#  
G#  
üb7th  
ü5th  
ü#4th  
G
ü6th  
ü#5th  
ü#4th  
ü#5th  
E
F#  
G
G
F
E b  
D
ü5th  
ü4th  
üı5th  
ü4th  
üı3rd  
Ref  
ü3rd  
F#  
F
F#  
ü5th  
ü3rd  
ü#4th  
ü3rd  
ü4th  
ꢀ
E b üꢀı3rꢀd  
D b  
F
ü3rd  
ü#2nd  
E
D
C
B
E
D
C
A
E
D
ꢀ
ü2nd  
ꢀ
E b  
C
E b  
C
üı3rd  
Ref  
ü2nd  
ü2nd  
ꢀRef  
¨2nd  
ü2nd  
ü2nd  
Ref  
ꢀRef  
ꢀRef  
C
C
C
Ref  
ꢀ
¨ı2nd  
B b  
G
B
A#  
B b  
A
¨ı3rd  
¨2nd  
¨2nd  
¨ı2nd  
¨ı3rd  
¨3rd  
¨ı5th  
¨5th  
¨6th  
B
¨2nd  
¨3rd  
A
G
E
D
C
G
F#  
F
G#  
F#  
E
A
¨4th  
¨ı3rd  
¨3rd  
¨4th  
¨5th  
¨6th  
¨Oct  
ꢀ
¨ı3rd  
¨4th  
¨b5th  
¨5th  
¨6th  
¨Oct  
¨4th  
ꢀ
G#  
F#  
E
F
G
G#  
F#  
F
¨ı6th  
¨ı7th  
¨ı5th  
ꢀ
E b  
C
F#  
E b  
E
¨b5th  
¨b6th  
¨ı6th  
ꢀ
¨ı5th  
ꢀ
E b  
C
D
¨Oct  
ꢀ
¨ı7th  
ꢀ
¨ı6th  
ꢀ
D
C
E b  
D
ꢀ
ꢀ
¨b7th  
¨Oct  
ꢀ
¨6th  
ꢀ
C
D b  
C
¨Oct  
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀꢀ  
ꢀꢀ  
¨ꢀ7th  
¨ı7th  
¨Oct  
C
¨Oct  
ꢀ
ꢀ
ꢀ
86  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Millennium Specifications  
Power Amp Section:  
DSP Section:  
80 Watts RMS per channel @ 8 ohms  
125 Watts RMS per channel @ 4 ohms  
A/D Converter: 20 bit 128X oversampled delta sigma stereo  
D/A Converter: 20 bit 128X oversampled  
Sampling frequency: 44.1 kHz  
Audio Outputs:  
Static Dynamic Instruction Set Computer (S-DISC II)  
Digital signal path width: 24 bits  
Internal Data path width: 24 bits  
Delay DRAM: 256 K x 24 (5.9 sec.)  
Delay SRAM: 256 24 bit registers  
Data ALU processing: 11.3 MIPS  
Left Speaker outputs: 2-1/4 inch jacks paralleled  
Right Speaker outputs: 2-1/4 inch jacks paralleled  
Loop Send: 1/4 inch TRS balanced / unbalanced: -10dBu  
Left/Right Direct/Recording  
Outputs: 2- XLR servo-balanced: +4 dBu:  
1 ground Maximum level: +18 dBu  
Impedance: 100 ohms  
Multiplier size: 24 x 24 bits  
DSP co-processor  
Audio Inputs:  
Digital Signal Path width: 24 bits  
Internal Data Path width: 48 bits  
Delay SRAM: 768 - 24 bit registers  
Data ALU processing: 22.6 MIPS  
Multiplier size: 24 X 24 bits  
Bright Input: 1/4 inch unbalanced:  
sensitivity adjustable by input level control  
Impedance: 1 megohm  
Normal Input: 1/4 inch unbalanced sensitivity  
adjustable by input level control  
Impedance: 1 megohm  
Loop Return: 1/4 inch unbalanced: +18 dBu  
Maximum Level: +18 dBu  
Power Requirements:  
100, 120, 230 and 240 VAC 50/60 Hz 550 W  
Fuse: 100, 120 VAC 1/4” X 1 1/4” 6A  
230, 240 VAC 5mm X 20mm 3.15A  
Impedance: 10 kΩ  
Controller Connections:  
MIDI: In, Out/Thru  
Expression Pedal inputs: 2- 1/4 inch;  
compatible with any standard volume pedal with 25K to 1M Ω  
or voltage control pedal (0-5v).  
Memory Capacity:  
Factory: 100 Presets  
User: 100 Presets  
J-3 footswitch input: 1/4inch TRS  
J-12 Controller Input: 5 pin DIN female  
Dimensions: 28” (711mm) W x 11” (265mm) H x 12” (305mm) D  
Net Weight: 42 lbs  
Shipping Weight: 47 lbs  
Tube Complement:  
2- 12Ax7 triodes: 300 volt power supply  
87  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
MIDI Implementation Chart  
Function...  
Default  
Transmitted  
Recognized  
1-16  
Remarks  
Basic  
Channel  
X
X
1-16  
Memorized  
Channel  
Default  
Messages  
Altered  
X
X
N/A  
Mode 2, Mode 4  
Mode 2, Mode 4  
X
Memorized  
Mode  
Note  
Number  
True Voice  
Note ON  
X
X
N/A  
X
X
X
X
X
X
Velocity  
Note OFF  
X
After  
Touch  
Key's  
Ch's  
X
X
X
X
X
O
0
Pitch Bender  
X
X
X
O
Control  
Change  
1*  
2*  
Preset  
Change  
X
O
X
N/A  
0-127  
True #  
System Exclusive  
System  
O
See SysEx (see appendix)  
:Song Pos  
:Song Sel  
:Tune  
:Clock  
:Commands  
X
X
X
Common  
System  
Real Time  
X
X
X
X
X
Aux  
Mes-  
sages  
:Local ON/OFF  
:All Notes Off  
:Active Sense  
:Reset  
X
X
X
X
X
X
X
X
Notes  
1* Each Parameter can be linked to any control change. These  
assignment tables are stored in memory.  
2* For Preset map 1-128 (Preset Change can be mapped to Factory  
Presets, User Presets, or Bypass function).  
Mode 1 : OMNI ON, POLY  
Mode 3 : OMNI OFF, POLY  
Mode 2 : OMNI ON, MONO  
Mode 4 : OMNI OFF, MONO  
O : Yes  
X : No  
88  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
System Exclusive Implementation  
MIDI System Exclusive communication allows a user to control a device directly through MIDI in a very powerful and flexible manner. Much  
care has gone into creating and testing this documentation but Johnson Amplification can not guarantee 100% accuracy, nor can Johnson  
Amplification be held responsible for presets and data lost in a product from System Exclusive Information use.  
A working knowledge of the MIDI Version 1.0 Detailed Specification can be useful while implementing any manufacturer's SysEx commands.  
For a copy of the MIDI spec contact:  
MIDI Manufacturers Association  
5316 West 57th Street  
Los Angeles, California 90056 USA  
(213) 649-6434  
It is a good practice to back up any user programs and/or user algorithms in the device before you begin to work with SysEx commands due to  
the fact that incorrect commands can produce unexpected results. Should you encounter any discrepancies between this documentation, and  
a Johnson Amplification S-DISC II™ MIDI, product please feel free to contact us at:  
Johnson Amplification  
Attn: Product Management Dept.  
8760 South Sandy Parkway  
Sandy, Utah 84070 USA  
(801) 566-8800  
http:///www.digitech.com  
MIDI Basics  
MIDI Channels: The Millennium can be set so that they communicate on 1 of 16 discrete MIDI channels. Some devices may also be set  
up to transmit or receive information on all channels in an Omni mode or to none of the channels in a Disabled mode.  
Preset Changes: When the Millennium is set to communicate on one or all of the MIDI channels, it will recognize a Preset Change  
command. If the number is legal (e.g. within the device’s range of selectable presets) the Johnson Amplification device will respond by  
changing to the new preset. MIDI sends Preset Changes 0 through 127. Johnson Amplification devices begin their preset numbering with 1,  
thus Preset Change 0 will select preset 1. The Millennium also allows the user to ‘re-map’ the Preset Change commands so that Preset  
Change 0 could call preset 135, if so desired.  
Continuous Controllers: A MIDI Continuous Controller may be ‘Linked’ to nearly any available parameter in the Millennium. CC links  
(Modifiers) and their ranges are treated uniquely in each preset with the assignments being saved only if they are stored as part of the  
preset.  
Channel Pressure: Johnson Amplification products treat Channel Pressure as simply another type of Continuous Controller which can be  
linked to parameters for control.  
89  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Pitch Bend: Pitch Bend information is a higher resolution controller that is not supported in Johnson Amplification products, due to the  
density of the information and the resources needed to process it properly. Many MIDI control products offer the ability to map Pitch Bend  
to normal Continuous Controllers if a user wanted to control a parameter with a device such as a Pitch Bend Wheel.  
General Format  
The general format for the System Exclusive information is as follows (note: all SysEx values are displayed in Hexadecimal format, along with  
this symbol (h) for clarification):  
Hex Value  
F0(h)  
Definition  
System Exclusive ‘Begin Message’ byte  
00(h)  
00(h)  
10(h)  
Manufacturer’s ID Number (Johnson Amplification)  
0n(h)  
n = Unit’s Device or SysEx Channel number (minus one)  
e.g.  
00(h)  
01(h)  
0F(h)  
is device or SysEx Ch 1  
is device or SysEx Ch 2 etc...  
is device or SysEx Ch 16  
dd  
pp  
dd = device ID number  
4A(h) identifies the Millennium  
pp = Procedure number. The different procedure’s names and general formats are  
described in the Procedures Section.  
dd(1)1, dd(1)2......dd(n)1, dd(n)2  
dd = Data as needed by procedures. Since the standard MMA MIDI Specification reserves 80(h)  
through FF(h) (decimal numbers 128 through 255) for specific commands, a split byte format is  
adopted for all data communication in this SysEx implementation. dd(n)2 denotes the 1st  
through 7th bits of the nth byte and dd(n)1 denotes th 8th bit of the nth byte. Note: All data that  
is requested or received, is in split byte format unless noted otherwise.  
F7(h)  
System Exclusive ‘End Message’ byte  
Procedures  
In the following section, SYS_HEAD refers to a valid System Exclusive header. The System Exclusive header starts with the System Exclusive  
status byte, and includes all bytes through the Johnson Amplification device type. F7(h) is the System Exclusive ‘Message End’ byte. All SysEx  
numbers in the format definition of each procedure are given as hexadecimal values, along with this symbol (h) for clarification. Binary  
numbers are identified with this symbol (b).  
90  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
REQUEST ONE PRESET (01h)  
SYS_HEAD, 01(h), yy1, yy2, zz1, zz2 F7(h)  
When yy = 00(h)  
When yy = 01(h)  
zz  
User bank is selected  
Factory bank is selected  
The Preset number, 1-100 User (00-63(h)) or 1-100 Factory (00-63(h))  
When a Request One Preset procedure is received, the Millennium will respond with a Receive One Preset procedure.  
RECEIVE ONE PRESET (42h)  
SYS_HEAD 42(h), vv(1)1, vv(1)2, vv(2)1, vv(2)2, yy1, yy2, zz1, zz2, dd(1st)1,dd(1st)2, ... dd(nth)1, dd(nth)2, F7(h)  
vv software version number  
When yy = 00(h)  
When yy = 01(h)  
zz  
User bank is selected  
Factory bank is selected  
The Preset number, 1-100 (00-63h)  
Preset data  
dd(n)  
The Receive One Preset procedure is used to load a preset into the Millennium. The number of preset bytes to be received (n) is different for  
each preset. If the Millennium is sent a Receive One Preset procedure where the preset number is not a valid RAM destination, it will be  
ignored.  
REQUEST BULK DUMP (49h)  
SYS_HEAD, 49(h), F7(h)  
When a Request Bulk Dump procedure is received, the Millennium will respond with a Receive Bulk Dump procedure.  
RECEIVE BULK DUMP (48h)  
SYS_HEAD 48(h), dd(1st)1 dd(1st)2, ... dd(nth)1, dd(nth)2, F7(h)  
dd(n)  
Bulk Dump Data  
The Receive Bulk Dump procedure is used to load all User Programs into the Millennium. A software version number is imbedded in the data.  
REQUEST UTILITY SETTINGS (11h)  
SYS_HEAD, 11(h), F7(h)  
When a Request Utility Settings procedure is received, the Millennium will respond with a Receive Utility Settings procedure.  
91  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
RECEIVE UTILITY SETTINGS (12h)  
SYS_HEAD 12(h), vv(1)1, vv(1)2, vv(2)1, vv(2)2, rr1, rr2, tt1, tt2, ee1, ee2, ff1, ff2, ss1, ss2, nn1, nn2, mm1,  
mm2, qq1, qq2, yy (1st)1,yy(1st)2, zz(1st)1,zz(1st)2 ... yy(128th)1,yy(128th)2, zz(128th)1,zz(128th)2, F7(h)  
vv =  
software version number  
rr =  
tt =  
ee =  
ff =  
ss =  
nn  
mm  
qq  
MIDI Receive Channel (range = 00(h) ~ 07(h))  
MIDI Transmit Channel (range = 00(h) ~ 07 (h)  
Cabinet Emulator (range = 00(h) ~ 07 (h)  
Foot Controller (range = 00(h) ~ 07(h))  
SysEx Channel (Millennium only)  
MIDI Merge On/Off (Millennium only)  
Mono-Stereo (range = 00(h) ~ 01(h)  
EQ mode (range = 00(h) ~ 07(h))  
Preset Map Settings (MIDI Preset changes 1 ~ 128 = map)  
User Bank is selected  
yy, zz  
When yy = 00(h)  
When yy = 01(h)  
When yy = 02(h)  
zz  
Factory Bank is selected  
and zz =00(h), Bypass toggle is selected  
Preset Number.  
REQUEST PARAMETER VALUE (17h)  
SYS_HEAD 17(h), aa1, aa2,bb's1, bb's2, F7(h)  
aa  
bb's  
Effect Module’s Position  
Effect Parameter’s Position  
When a Request Parameter Value procedure is received, the Millennium will respond with a Receive Parameter Value procedure.  
RECEIVE PARAMETER VALUE (18h)  
SYS_HEAD 18(h), aa1,aa2, bb's1, bb's2,cc1, cc2, F7(h)  
aa  
bb's  
cc  
Effect Module’s Position  
Effect Parameter’s Position  
Parameter Value  
The Receive Parameter Value procedure is used to load Parameter Values into the Millennium. Please refer to the Parameter Charts for more  
information.  
REQUEST ALL CURRENT PARAMETER VALUES (23h)  
SYS_HEAD, 23(h), ww1, ww2, F7(h)  
92  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
When ww= 7F(h)  
When ww= 68(h)  
ww  
All module’s parameters will be requested.  
(position of the module minus 1), only that module’s parameters will be requested.  
Requested Module’s parameter Values  
When a Request All Current Parameter Values procedure is received, the Millennium will respond with a Respond All Current Parameter  
Values procedure.  
RECEIVE ALL CURRENT PARAMETER VALUES FOR CURRENT PRESET (24h)  
SYS_HEAD, 24(h), nn1, nn2, ww1, ww2, mm1(1st), mm2(1st), aa1(1st), aa2(1st), dd1(1st)(1st), dd2(1st)1st, ... dd1(1st)(wth) ,dd2(1st)(wth),  
... mm1(xth),...mm2(xth), aa1(xth), aa2(xth), dd1(xth)(1st), dd2(xth)(1st), ... dd1(xth)(wth),dd2(xth)(wth), F7(h)  
When ww= 7F(h)  
When ww= 68(h)  
All module’s parameters will be received.  
(position of the modules minus 1), only that module’s parameters will be received.  
nn  
ww  
mm  
aa  
Number of Modules.  
Modules User requested.  
Indicates the beginning of the xth Module.  
Number of available parameters in the FX Module.  
Current value for the wth parameter.  
dd  
The Receive All Current Parameter Values procedure is used to receive Parameter Values from the Millennium for the currently selected  
program.  
Warning: Sending data that was retrieved from a different preset will delete the memory. Be sure to only send data that was received from  
the same preset.  
REQUEST MODULE CONFIGURATION (25h)  
SYS HEAD , 25 (h) , F7 (h)  
When a Request Module Configuration procedure received, the Millennium will respond with a Respond Module Configuration procedure.  
RESPOND MODULE CONFIGURATION (26h)  
SYS HEAD , 26(h) , nn1, nn2, cc(1st)1,cc(1st)2, ee(1st)1, ee(1st)2, ... cc(nth)1, cc(nth)2 , ee(nth)1, ee(nth)2, F7(h)  
nn  
cc  
Number modules present in the algorithm  
Class I.D. of the nth module in the algorithm  
ee  
I.D. number of the effect currently loaded in the nth module (see pg. 12 for ID numbers)  
Class I.D. Numbers for millennium  
00(h)  
01(h)  
Amplifier Type  
1/4 Effect Module  
93  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
02(h)  
03(h)  
04(h)  
1/2 Effect Module  
3/4 Effect Module  
Whole Effect Module  
RECEIVE KEY SCAN CODE (54h)  
SYS_HEAD, 54(h), cc, F7(h)  
cc Code for the Key Scan (note: there is only one byte, not two)  
The Receive Key Scan Code procedure is used to emulate a button press on the front panel of the. See the Key Scan Code Maps (page 96) for a  
list of Key Scan codes.  
RECEIVE HOLD KEY SCAN CODE (55h)  
SYS_HEAD, 55(h), cc, 68, F7(h)  
cc Code for the Key Scan (note: there is only one byte, not two)  
68Time key is pressed expressed in 0.1 seconds increments (note: there is only one byte, not two)  
The Receive Hold Key Scan Code procedure is used to emulate a button press and hold on the front panel of the Millennium. The device will  
respond with a Receive Key Accepted procedure.  
RECEIVE KEY ACCEPTED (56h)  
SYS_HEAD, 56(h), cc1, cc2, F7(h)  
cc Code echoed for the Key Scan received. (00(h) if key is invalid)  
The Receive Key Accepted procedure is sent from the Millennium in response and acceptance of a Receive Scan Code Key or Receive Hold Scan  
Code Key procedure but is ignored if received by the Millennium.  
SELECT ONE PRESET (1Fh)  
SYS_HEAD, 1F(h), yy1, yy2, zz1, zz2 F7(h)  
When yy = 00(h)  
When yy = 01(h)  
zz  
User bank is selected  
Factory bank is selected.  
The Preset number, 1-100 User (00-63(h)) or 1-191 Factory (00-BE(h))  
This command behaves like a standard MIDI Preset Change command, except that it allows the selection of any preset in the Millennium  
without the use of mapping.  
94  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section -7 Appendix  
RESET PRESET (20h)  
SYS_HEAD, 20(h), F7(h)  
The Reset Preset procedure causes the Millennium to reload the current saved program.  
RESET DEVICE (21h)  
SYS_HEAD, 21(h), F7(h)  
The Reset Device procedure causes the Millennium to reboot the software as if the power had been turned off, and then back on. If edits have  
been made to the current preset without saving, they will be lost.  
RESET FACTORY SETTINGS (22h)  
SYS_HEAD, 22(h), F7(h)  
The Reset Factory Settings procedure causes the Millennium to reload a sections of the EPROM factory defaults and perform a hard reset.  
REQUEST USER DEFAULTS (13h)  
SYS_HEAD, 13(h), yy1, yy2, zz1, zz2 F7(h)  
When a Request User Default procedure is received, the Millennium will respond with a Receive User Defaults procedure.  
yy= effect ID #  
zz= index map max = 5  
FX ID # = 255  
RECEIVE USER DEFAULTS (14h)  
SYS_HEAD,14(h), yy1, yy2, zz1, zz2 F7(h)  
The Receive User Defaults procedure is used to receive User Defaults.  
yy= effect ID #  
zz= index map max = 5  
FX ID # = 255  
95  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
SysEx Button/Keys/Footswitch codes  
The following are codes for each of the buttons or keys on the Millennium. Numbers are given as hexadecimal values.  
Key Label  
Hex equivalent  
Key Label  
Hex equivalent  
Input Knob  
Mix/Page  
RVB  
DLY  
PCH  
MOD  
Gain  
Treble  
Mid  
54(h)  
10(h)  
F(h)  
E(h)  
D(h)  
J-12 Bank Up  
J-12 Bank Down  
Preset button  
Digital Effect Bypass  
Utility button  
Edit button  
41(h)  
42(h)  
01(h)  
02(h)  
03(h)  
09(h)  
A(h)  
C(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
5(h)  
Assign button  
Store button  
B(h)  
American Stk button  
American Combo button  
British Stack  
British Combo  
Johnson button  
Configuration button  
Mod button  
Delay button  
Reverb button  
Other button  
21(h)  
29(h)  
22(h)  
24(h)  
23(h)  
11(h)  
12(h)  
13(h)  
19(h)  
1a(h)  
1b(h)  
Bass  
Level  
J-3 FS A  
J-3 FS B  
J-3 FS C  
J-3 Preset Up  
J-3 Preset Down  
J-3 List Up  
J-3 List Down  
J-12 Fs 1  
J-12 Fs 2  
J-12 Fs 3  
J-12 Fs 4  
J-12 Fs 5  
J-12 Fs 6  
J-12 Fs 7  
J-12 Fs 8  
J-12 Fs 9  
J-12 Fs 10  
6(h)  
7(h)  
24(h)  
25(h)  
26(h)  
27(h)  
31(h)  
32(h)  
33(h)  
35(h)  
36(h)  
37(h)  
38(h)  
39(h)  
40(h)  
41(h)  
TapIt button  
96  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
SysEx Preset Dump Example  
For those of you that are reluctant to stick your feet in the SysEx water, we have included a simple example of a SysEx Preset jump. It takes  
you set by step through all of the operation commands of a typical SysEx procedure.  
<<SysEx Header>>  
F0 00 00 10 47  
<<Procedure>>  
42  
<<Preset Dump Version>>  
00 01 00 01  
<<Bank and Preset for User Preset 1>>  
00 00 00 00  
<<Preset’s Transmit Count...Lo Bytes, Hi Bytes>>  
00 0A 00 06  
<<FX Module Count for Module IDs>>  
00 07  
<<Module ID Numbers>>  
00 0C 00 10 00 15 00 20 00 01 00 5A 00 77  
<<Algorithm Number>>  
00 00  
<<FX Module Count for Module Types>>  
00 07  
<<FX Module Class Type  
00 22 00 24 00 18 00 07 00 00 00 06 00 03  
<<20 Character Preset Name...dynamic>>  
00 31 00 3A 00 52 00 76 00 62 00 20 00 32 00 3A 00 47 00 74 00 52 00 76  
00 20 00 33 00 3A 00 44 00 6C 00 79 00 20 00 34 00 3A 00 43 00 68 00 6F  
<<Null to indicate end of Character String>>  
00 00  
<<Misc Preset Data...too dynamic to document>>  
00 07 00 00 00 06 00 00 00 03 00 06 00 03 00 32 00 08 00 03 00 00 00 00 00 02 00 04 00 00 00 00 00 02 00 08  
00 00 00 00.....  
...... 01 7E 00 00 00 00 00 20 01 7F 00 00 00 00 00 20 00 00 00 00 00 00 00 20 00 01 00 00 00  
00 00 20 00 02 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00  
<<SysEx End>>  
F7  
NOTE: When the length of the program name is modified, the Preset’s Transmit Count must also be  
modified accordingly.  
97  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
10(h)  
11(h)  
12(h)  
08(h)  
Default type  
Fx Module codes and numbers  
The Following chart shows all effect modules and their respective parameters with  
SysEx Effect I.D. numbers attached.  
Page 2  
Page 3  
Level  
Phase  
80Hz  
140Hz  
250Hz  
450Hz  
800Hz  
1.5kHz  
2.5kHz  
4.5kHz  
8kHz  
FX # FX Name EditPage P#  
Parameter Name  
On/Off  
131(h)  
Tube Dist.  
Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
Default type  
Page 4  
Page 2  
Distortion Type  
Gain level  
132(h)  
Tube EQ  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
10(h)  
11(h)  
12(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
On/Off  
Default type  
Level  
Page 5  
Page 1  
15kHz  
Phase  
135(h)  
Noise Gate  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
On/Off  
80Hz  
Default type  
Noise gate Type  
Threshold  
Attenuation  
Attack  
140Hz  
250Hz  
450Hz  
800Hz  
1.5kHz  
2.5kHz  
4.5kHz  
8kHz  
Page 2  
Page 3  
Page 4  
Release  
3F(h)  
GEQ 8  
Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
On/Off  
FX Type  
Default Type  
Level  
Page 5  
Page 4  
15kHz  
160Hz  
250Hz  
400Hz  
630Hz  
1kHz  
Page 2  
Page 3  
Phase  
80Hz  
160Hz  
Page 5  
Page 6  
315Hz  
1.6kHz  
2.5kHz  
4.0kHz  
6.3kHz  
10.0kHz  
16.0kHz  
630Hz  
Page 4  
1.25kHz  
2.5kHz  
5.0kHz  
10.0kHz  
40(h)  
GEQ 15  
Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
On/Off  
FX Type  
Default Type  
Level  
133(h)  
134(h)  
S. State Dist. Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
On/Off  
Default type  
Distortion Type  
Distortion Gain  
Page 2  
Page 3  
Page 2  
Phase  
25Hz  
40Hz  
S. State EQ  
Page 1  
00(h)  
On/Off  
63Hz  
98  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
100Hz  
160Hz  
250Hz  
400Hz  
630Hz  
1kHz  
1F(h)  
20(h)  
21(h)  
22(h)  
23(h)  
8.0kHz  
Page 4  
10.0kHz  
12.5kHz  
16.0kHz  
18.0kHz  
Page 9  
Page 5  
Page 6  
1.6kHz  
2.5kHz  
4.0kHz  
6.3kHz  
10.0kHz  
16.0kHz  
41(h)  
St GEQ 8  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
On/Off  
FX Type  
Default  
Level  
Phase L  
Phase R  
80Hz  
43(h)  
GEQ 31  
Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
19(h)  
1A(h)  
1B(h)  
1C(h)  
1D(h)  
1E(h)  
On/Off  
FX Type  
Default Type  
Level  
160Hz  
315Hz  
630Hz  
1.25kHz  
2.5kHz  
5.0kHz  
10.0kHz  
Page 2  
Page 3  
Page 4  
Phase  
20Hz  
25Hz  
31.5Hz  
40Hz  
Page 4  
Page 5  
Page 6  
Page 7  
Page 8  
Page 9  
50Hz  
44(h)  
St PEQ 3  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
On/Off  
63Hz  
FX Type  
80Hz  
Default  
100Hz  
125Hz  
160Hz  
200Hz  
250Hz  
315Hz  
400Hz  
500Hz  
630Hz  
800Hz  
1.0kHz  
1.25kHz  
1.6kHz  
2.0kHz  
2.5kHz  
3.15kHz  
4.0kHz  
5.0kHz  
6.3kHz  
Level  
PhaseL  
PhaseR  
Page 3  
Page 4  
Page 5  
Band1 Freq  
Width Level  
Band2 Level  
Width Level  
Band3 Freq  
Width Level  
45(h)  
PEQ 6  
Page 1  
00(h) On/Off  
01(h)  
FX Type  
Default  
02(h)  
Page 2  
Page 3  
Page 4  
03(h)  
Level  
04(h)  
Phase Inv  
LoShlv Freq  
Level  
05(h)  
06(h)  
07(h)  
Band1 Freq  
Width Level  
08(h)  
99  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Page 5  
Page 6  
Page 7  
Page 8  
09(h)  
Band2 Freq  
Width Level  
Band3 Freq  
Width Level  
Band4 Freq  
Width Level  
HiShlv Freq  
Level  
0C(h)  
0D(h)  
0E(h)  
PanA  
OutB  
PanB  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
20(h)  
Quad Cho  
Page 1  
Page 2  
Page 3  
Page 4  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Speed  
Depth  
Waveform  
DlyA  
46(h)  
St PEQ 6  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
On/Off  
FX Type  
Default  
Level  
Phase L  
Phase R  
Loshlv Freq  
Level  
DlyB  
Page 3  
Page 4  
DlyC  
DlyD  
Band1 Freq  
Width  
Page 5  
Page 6  
OutA  
PanA  
Level  
OutB  
Page 5  
Page 6  
Page 7  
Page 8  
Page 1  
Page 2  
Page 3  
Band 2 Freq  
Width  
PanB  
OutC  
Level  
PanC  
Band3 Freq  
Width  
OutD  
PanD  
Level  
Band4 Freq  
Width  
22(h)  
Octal Cho  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Speed  
Depth1  
Depth2  
Speed  
Depth  
DlyA  
Level  
HiShlv Freq  
Level  
1F(h)  
Dual Cho  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Speed  
Page 4  
Page 5  
DlyB  
Depth  
DlyC  
Waveform  
DlyA  
DlyD  
Page 4  
Page 5  
Page 6  
DlyE  
DlyB  
DlyF  
OutA  
DlyG  
100  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
12(h)  
13(h)  
DlyH  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
19(h)  
1A(h)  
Rotor Lvl  
Page 7  
Spread  
Page 4  
Page 5  
Dummy (ignore)  
Horn Slow Speed  
Horn Slow Depth  
Horn Slow Doppler  
Dummy (ignore)  
Horn Fast Speed  
Horn Fast Depth  
Horn Fast Doppler  
Dummy (ignore)  
Rotor Slow Speed  
Roto Slow Depth  
Dummy (ignore)  
Rotor Fast Speed  
Roto Fast Depth  
X-Over  
47(h) Dual Flange  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
On/Off  
FX Type  
Default  
FX level  
Dry Level  
Balance  
Speed  
Page 6  
Page 7  
Page 8  
Depth  
Feedback  
Waveform  
DlyA  
Page 4  
Page 5  
DlyB  
OutA  
PanA  
Horn Acceleration  
Rotor Acceleration  
OutB  
PanB  
50(h) St. Tremolo  
51(h) AutoPanner  
2C(h) Dual Detune  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
On/Off  
FX Type  
Default  
Level  
4B(h) Dual Phaser  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Speed  
Speed  
Depth  
Waveform  
Depth  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
On/Off  
FX Type  
Default  
Level  
Feedback  
Waveform  
OutA  
Page 4  
PanA  
Speed  
OutB  
Depth  
PanB  
Waveform  
30(h)  
Rotary Speaker Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
On/Off  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
DtnA  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Mode  
Page 2  
Page 3  
Spread  
DtnB  
Horn Lvl  
DlyA  
101  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
09(h)  
DlyB  
OutA  
PanA  
OutB  
PanB  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
DlyB  
DlyC  
DlyD  
DlyE  
DlyF  
DlyG  
DlyH  
Page 4  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
Page 6  
2E(h)  
Quad Detune  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
DetnA  
DetnB  
DetnC  
DetnD  
DlyA  
Page 7  
Page 1  
Spread  
26(h) Smooth Pitch  
00(h)  
01(h)  
On/Off  
FX Type  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
Default  
FX Level  
Dry Level  
Balance  
Shft  
Page 2  
Page 3  
Page 4  
Page 5  
Page 6  
DlyB  
Dtn  
DlyC  
OutB  
DlyD  
PanB  
OutA  
PanA  
28(h)  
Dual Pitch  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
ShftA  
OutB  
PanB  
OutC  
PanC  
OutD  
PanD  
DtnA  
2F(h) Octal Detune  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
DetnA  
ShftB  
DtnB  
Page 4  
OutA  
PanA  
OutB  
PanB  
DetnB  
DetnC  
DetnD  
DetnE  
2A(h)  
Quad Pitch  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
ShftA  
Page 4  
Page 5  
DetnF  
DetnG  
DetnH  
DlyA  
DtnA  
102  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
ShftB  
DtnB  
ShftC  
DtnC  
ShftD  
DtnD  
Out A  
PanA  
OutB  
PanB  
OutC  
PanC  
OutD  
PanD  
1D(h)  
1E(h)  
OutH  
Page 9  
Page 1  
Spread  
Page 4  
Page 5  
Page 6  
27(h) Stereo Pitch  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Shft  
Page 2  
Page 3  
Dtn  
OutL  
OutR  
29(h) St Dual Pitch  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
ShftA  
2B(h) Octal Pitch  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
19(h)  
1A(h)  
1B(h)  
1C(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
ShftA  
DtnA  
DetnA  
ShftB  
ShftB  
DtnB  
DtnB  
Page 4  
OutLA  
OutLB  
OutRA  
OutRB  
Page 4  
Page 5  
Page 6  
Page 7  
Page 8  
ShftC  
DetnC  
ShftD  
DetnD  
ShftE  
25(h)  
Harmony  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Key  
DetnE  
ShftF  
DetnF  
ShftG  
DetnG  
ShftH  
DetnH  
OutA  
Scale  
Page 4  
Page 5  
Interval  
Level  
OutB  
OutC  
Pan  
OutD  
12(h)  
14(h)  
19(h)  
Delay(370ms)  
Delay(700ms)  
OutE  
OutF  
Delay(1400ms) Page 1  
00(h)  
01(h)  
On/Off  
OutG  
FX Type  
103  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
02(h)  
Default  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
OutB  
PanB  
Page 2  
Page 3  
Page 4  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
Tapit (ignore)  
Out  
Page 6  
OutC  
PanC  
OutD  
PanD  
17(h)  
1C(h)  
S Delay(370ms)  
Pan  
S Delay(700ms) Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
On/Off  
FX Type  
Default  
Dual Dly(370ms)  
15(h) Dual Dly(700ms)  
Page 2  
Page 3  
Page 4  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
Tapit (ignore)  
OutL  
1A(h) Dual Dly(1400ms) Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
Tapit (ignore)  
DlyA  
Page 2  
Page 3  
OutR  
18(h) St. Dl Dly(370ms)  
Page 4  
Page 5  
1D(h) St. Dl Dly(700ms) Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
On/Off  
DlyB  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
Tapit (ignore)  
DlyA  
OutA  
PanA  
Page 2  
Page 3  
OutB  
PanB  
16(h) Quad Dly(700ms)  
1B(h) Quad Dly(1400ms) Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
Tapit (ignore)  
DlyA  
Page 4  
Page 5  
DlyB  
Page 2  
Page 3  
Page 4  
OutLA  
OutLB  
OutRA  
OutRB  
1E(h) St. Quad Delay  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
On/Off  
FX Type  
Default  
DlyB  
DlyC  
FX Level  
Dry Level  
Balance  
Delay Time  
DlyD  
Page 5  
OutA  
PanA  
104  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
11(h)  
13(h)  
14(h)  
FeedBack  
Tapit (ignore)  
DlyA  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
Freq  
Gain  
OutL  
OutR  
Page 4  
Page 5  
Page 6  
Page 5  
Page 1  
Page 2  
DlyB  
DlyC  
DlyD  
37(h) Chorus/Dly  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
On/Off  
OutLA  
OutLB  
OutLC  
OutLD  
OutRA  
OutRB  
OutRC  
OutRD  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Page 3  
Page 4  
Route  
Speed  
Depth  
Page 5  
Page 6  
WvFrm  
32(h)  
34(h)  
36(h)  
Alog Dly(370ms)  
Chorus Delay  
Delay Time  
Delay Feedback  
Tapit (ignore)  
Chorus Level  
Chorus Pan  
Delay Level  
Delay Pan  
Alog Dly(700ms)  
Alog Dly(1400ms) Page 1  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay Time  
FeedBack  
TapIt (ignore)  
Smear  
Page 7  
Page 2  
Page 3  
Page 4  
38(h) Flange/Dly  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
On/Off  
FX Type  
Default  
LPF Type  
Freq  
FX Level  
Dry Level  
Balance  
Gain  
Page 5  
Out  
Page 3  
Page 4  
Route  
Pan  
Speed  
Depth  
33(h) St A.Dly(370ms)  
35(h) St.A.Dly(700ms)  
Flange Feedback  
WvFrm  
Page 1  
Page 2  
Page 3  
Page 4  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
On/Off  
Page 5  
Page 6  
FX Type  
Flange Delay  
Delay Time  
Delay Feedback  
Tapit (ignore)  
Flange Level  
Flange Pan  
Delay Level  
Delay Pan  
Balance  
Default  
FX Level  
Dry Level  
Balance  
Page 7  
Delay Time  
FeedBack  
TapIt (ignore)  
Smear0A(h) LPF Type  
105  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
Page 8  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
Secondary Decay  
09(h) PreDelay  
Page 1  
Page 2  
Page 3  
Page 4  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
On/Off  
Secondary Size  
Second Reflection  
Primary OutL  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay  
Page 9  
Primary OutR  
Page 10  
Secondary OutL  
Secondary OutR  
Filter Type  
Frequency  
OutL  
0D(h) Stereo Reverb  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Reverb Type  
Decay  
OutR  
0A(h)  
Reverb  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Type  
Page 3  
Page 4  
Page 5  
Density  
Diffusion  
Blend  
Page 3  
Page 4  
Page 5  
OutL  
Decay  
OutR  
Density  
Diffusion  
OutL  
10(h) Gated Reverb  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Type  
OutR  
0C(h) Dual Reverb  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
On/Off  
FX Type  
Default  
Page 3  
Page 4  
Page 5  
FX Level  
Time  
Dry Level  
Density  
LowPass  
OutL  
Balance  
Density  
Diffusion  
OutR  
Dispersion  
X-Over Type  
Frequency  
Page 4  
Page 5  
Page 6  
Page 7  
11(h) St Gated Reverb  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Type  
Primary X-Over  
Secondary X-Over  
Primary Damp  
Secondary Damp  
Primary Decay  
Primary Size  
Primary Reflection  
Page 3  
Page 4  
Time  
Density  
106  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Johnson Millennium  
Section - 7 Appendix  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
Dispersion  
Low Pass  
Blend  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
00(h)  
Thrsh Closed  
Attn  
Page 5  
Page 3  
Delay  
OutL  
Attack  
OutR  
Hold  
Release  
FX Type  
8(h) Spring Reverb  
Page 1  
Page 2  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
On/Off  
7D(h) Thru  
Page 1  
Page 1  
FX Type  
Default  
7E(h)  
Mute  
00(h)  
FX Ty  
FX Level  
Dry Level  
0F(h) Room Echo  
Page 1  
Page 2  
Page 3  
00(h)  
01(h)  
02(h)  
03(h)  
04(h)  
05(h)  
06(h)  
07(h)  
08(h)  
09(h)  
0A(h)  
0B(h)  
0C(h)  
0D(h)  
0E(h)  
0F(h)  
10(h)  
11(h)  
12(h)  
13(h)  
14(h)  
15(h)  
16(h)  
17(h)  
18(h)  
On/Off  
FX Type  
Default  
FX Level  
Dry Level  
Balance  
Delay A  
Delay B  
Delay C  
Delay D  
Out A  
Page 4  
Page 5  
Bal A  
Out B  
Bal B  
Out C  
Bal C  
Out D  
Bal D  
Page 6  
Page 7  
Shape Type  
Spread  
Diffusion  
Feedback Delay  
Feedback Amount  
OutL  
Page 8  
Page 1  
Page 2  
OutR  
52(h) Noise Gate  
00(h)  
01(h)  
02(h)  
04(h)  
05(h)  
On/Off  
FX Type  
Default  
Level  
Thrsh Open  
107  
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8760 South Sandy Parkway  
Sandy, Utah, 84070  
Telephone 801.566.8800  
FAX 801.566.7005  
International Distribution:  
3 Overlook Drive, Unit 4  
Amherst, New Hampshire 03031 U.S.A.  
FAX 603.672.4246  
Johnson Amplification™, Millennium™, and S-DISC™II are registered trademarks  
of the Harman Music Group Incorporated  
Copyright © 1997  
the Harman Music Group Incorporated  
Printed In U.S.A. 10/97  
Manufactured in the U.S.A.  
Millennium Stereo 250 H 18-2266-A  
Please Visit Johnson Amplification on the World Wide Web at:  
http/digitech.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Welding Consumables km 2014 User Manual
Milwaukee Drill 5378 20 User Manual
Mr Coffee Coffeemaker UN12 User Manual
NETGEAR Network Router GS728TP User Manual
NextBase Portable DVD Player SDV27 SD User Manual
Optimus Cassette Player CTR 106 User Manual
Optoma Technology Projector HD81 LV User Manual
Orange Micro CRT Television 4GS User Manual
Oreck Vacuum Cleaner BB870AD User Manual
Panasonic Answering Machine KX TG242SK User Manual