Owner's Manual
TB110MW9
DTV Digital to Analog Converter
(Set Top Box)
THANK YOU FOR CHOOSING MAGNAVOX.
NEED HELP FAST?
READ YOUR OWNER'S MANUAL FIRST FOR QUICK TIPS
THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE.
IF YOU HAVE READ YOUR INSTRUCTIONS AND STILL NEED ASSISTANCE,
YOU MAY ACCESS OUR ONLINE HELP AT HTTP://WWW.FUNAI-CORP.COM
OR CALL 1-800-605-8610 WHILE WITH YOUR PRODUCT.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
© 2008 Funai Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA LEAD
INWIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
NEC - NATIONAL
ELECTRICAL CODE
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE
SYSTEM (NEC ART 250, PART H)
conductors, location of antenna-discharge unit,
a. When the power-supply cord or plug is damaged
or frayed.
connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
b. If liquid has been spilled, or objects have fallen into
14. Lightning - For added protection for this product
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to
this product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as
contact with them might be fatal.
this product.
c. If this product has been exposed to rain or water.
d. If this product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore this product to its normal operation.
e. If this product has been dropped or damaged in
any way.
f. When this product exhibits a distinct change in
performance-this indicates a need for service.
16. Overloading - Do not overload wall outlets and extension
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, injury to persons or other hazards.
21. Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform routine safety checks to determine that this
product is in proper operating condition.
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on this product.
18. Servicing - Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
22. Heat - This product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
19. Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
The serial number of this product may be found on the bottom of the unit. You should record the number and
other vital information here and retain this book as a permanent record. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling,
standing or climbing on it. A falling unit can cause serious injury or even death.
3
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Precautions
Location
Important Copyright Information
For safe operation and satisfactory performance
of this product, keep the following in mind when
selecting a place for its installation:
Unauthorized recording or use of broadcast
television programming, video tape, film or other
copyrighted material may violate applicable
copyright laws. We assume no responsibility for the
unauthorized duplication, use or other acts which
infringe upon the rights of copyright owners.
•
Shield it from direct sunlight and keep it away
from sources of intense heat.
•
•
Avoid dusty or humid places.
Avoid places with insufficient ventilation for
proper heat dissipation. Do not block the
ventilation holes at the top and bottom of the
product. Do not place the product on a carpet
because this will block the ventilation holes.
FCC WARNING - This equipment may generate
or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction
manual. The user could lose the authority to
operate this equipment if an unauthorized
change or modification is made.
•
•
•
Install the product in a horizontal position.
Avoid locations subject to strong vibration.
Do not place this product near strong magnetic
fields.
•
Avoid moving this product to locations where
temperature differences are extreme.
Avoid the Hazards of Electrical
Shock and Fire
•
Do not handle the power cord with wet hands.
•
Do not pull on the power cord when
disconnecting it from an AC wall outlet. Grasp it
by the plug.
•
•
If by accident, water is spilled on your the
product, unplug the power cord immediately
and take the product to our Authorized Service
Center for servicing.
Do not place anything directly on top of the
product.
A Note about Recycling
This product’s packaging materials are recyclable
and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or
incinerated but disposed of in accordance with your
local regulations concerning chemical wastes.
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
T a b l e o f C o n t e n t s
Before Using
Advanced Operation
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Information on Digital Broadcasting . . . . . . . . . . . . . . . 7
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Location of Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Autoscan (Receiving Channels) . . . . . . . . . . . . . . . . . . . 18
Adding/Deleting Channels . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Selecting Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting the Time Zone and D.S.T
(Daylight Saving Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
V-chip Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Closed Caption Options . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Auto Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Viewing Analog TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connections
Connecting to a TV without A/V Jacks . . . . . . . . . . . . 10
Connecting to a TV with A/V Jacks . . . . . . . . . . . . . . . . 10
Connecting to a Cable Box (Optional). . . . . . . . . . . . . 11
Connecting to Other Devices. . . . . . . . . . . . . . . . . . . . . 12
Others
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Initial Setup (Setup Wizard)
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Basic Operation
Selecting Channels on the STB . . . . . . . . . . . . . . . . . . . 15
© 2008 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the
content herein without the obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property
of their respective owners. Nothing contained in this manual should be construed as granting, by implication
or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or
any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property
rights to the fullest extent of the law.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
5
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Overview
CONNECTION
Connecting to
A
TV without
A/V jacks
SET TOP BOX
P
P
10
a TV without A/V jacks
Conexión a un TV sin tomas de A/V
Connecting to
B
C
TV with
A/V jacks
SET TOP BOX
10
a TV with A/V jacks
Conexión a un TV con tomas de A/V
Connecting to
Cable Box
TV with
A/V jacks
SET TOP BOX
P
11
a Cable Box
Conexión a una caja de
cable
Connecting to
D
DVD or VCR
TV with
A/V jacks
SET TOP BOX
P
12
Other Devices
Conexión a otros
dispositivos
SETUP WIZARD
1. Language for TV screen
Idioma para la pantalla
2. Connection for audio output
Conexión para salida de audio
3. Time zone
Husos horarios
P
14
4. Daylight savings time (D.S.T)
Hora de verano (D.S.T)
5. Display mode
modo de indicaciones
6. Channel scanning
Búsqueda de canales
Viewing Analog TV
P
27
Viendo TV Analógica
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Digital Broadcasting
This STB makes it possible to view the digital TV
programs on your analog TV by converting the
digital signal to the analog signal. You can use
most features provided by the digital broadcast,
except that the resolution of the image is always
output in 480i (standard resolution).
ATSC
Receives
ATSC
Digital
terrestrial signals
Digital terrestrial
antenna
STB (Set Top Box)
converts the ATSC signal
to analog signal
TV
Accessories
Check the following accessories when unpacking the STB:
Remote control:
NA386UD (x1)
Owner’s manual:
1VMN25977 (x1)
AA battery (x2)
RF cable:
WPZ0901TM002 /
WPZ0901TM005 (x1)
Installing Batteries
Instalación de pilas
1
Unsnap the battery cover from the
back of the remote control.
2
Install two AA batteries making
sure the polarity (+ / ) is correct.
3
Snap the battery
-
cover back.
Cierre la cubierta de
pilas.
Abra la cubierta de pilas de la parte
Instale dos pilas AA asegurándose que
trasera del mando a distancia.
la polaridad (+ / ) sea la correcta.
-
CAUTION:
NOTE:
•
Do not mix battery types (alkaline and manganese, or old ones and
new ones).
No mezcle tipos de baterías (baterías alcalinas y de manganeso, ni pilas viejas
con pilas nuevas).
•
When replacing batteries,
replace them in pairs.
•
•
Do not recharge, short-circuit, heat, burn or disassemble batteries.
No recargue, caliente, queme o desarme baterías ni provoque un corto circuito
con ellas.
Cuando cambie las pilas,
hágalo por pares.
Remove batteries from battery compartment that is not going to be
used for a month or more.
Quite las pilas del compartimento de pilas si no se va a utilizar durante un mes o más.
7
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Location of Controls
Ubicación del control
Remote Control
Mando a distancia
1
STANDBY-ON button: Turns STB on and off.
Conecta y desconecta el STB.
2
3
4
Number buttons
OK button
1
2
SETUP button: Displays “SETUP”menu.
Switches “RF OUT”setting by holding this button
down over 3 seconds.
Despliega el menú “AJUSTE”.
Cambia la configuración de “SALIDA RF”al mantenerse
presionado durante 3 segundos.
7
8
9
10
5
6
ALT. CH: Returns to the last selected channel.
3
4
Regresa al último canal seleccionado.
AUDIO button: Selects alternative audio
languages (if available).
Selecciona idiomas de audio alternativos (si existen).
5
6
11
12
13
7
. (Confirm) button: Press to confirm the channel
selection made by [the Number buttons].
Presione para confirmar la selección del canal, hecha
con [los botones de Números].
8
9
DISPLAY button: Displays the channel banner.
Despliega el banner del canal.
RETURN button: Returns to the previous menu
screen.
Regresa a la pantalla de menú anterior.
10 Navigation buttons K / L / s /
B
11 EPG button: Displays the Electronic Program
Guide.
Despliega la Guía Electrónica de Programas.
12 CH K / Lbuttons
13 STILL button: Freezes the image on the TV
screen.
Congela la imagen de la pantalla del TV.
•
To operate this STB with a universal remote, check the instruction manual for remote and find
Magnavox brand STB code. If you do not find the code or the code does not work, try to use Sylvania
brand STB code instead.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
Panel frontal
1
2
1
2
Remote control sensor
POWER indicator:
Turns green when the STB is in operation.
Se vuelve verde cuando el STB está en operación.
Rear Panel
Panel trasero
1
2
3
4 5
1
2
AC power cord
4
ANT. IN jack:
Connect an antenna.
Conecte una antena.
AUDIO OUT jacks (Right-red / Left-white):
Connect your TV, stereo system or VCR etc. with
standard audio cables.
5
ANT. OUT jack:
Conecte su TV, sistema estéreo o VCR, etc., con cables
de audio estándares.
Connect to the ANT. IN jack on your TV.
Conecte a la toma ANT. IN de su TV.
3
VIDEO OUT jack (yellow):
Connect your TV or VCR etc. with a standard
video cable.
Conecte su TV o VCR, etc., con un cable estándar de
video.
9
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
1
2
3
4
Disconnect the AC power cords of the devices from the AC outlet.
Desconecte los cables de alimentación de los aparatos del tomacorriente CA.
Disconnect RF coaxial cable from antenna input jack of your TV.
Desconecte el cable coaxial de RF del conector hembra de entrada de antena de su televisor.
Make the connections as illustrated below.
Efectúe las conexiones tal como se ilustra a continuación.
Plug all AC power cords into AC outlets, then turn all devices on.
Enchufe todos los cables eléctricos de CA en los tomacorrientes de CA y conecte la alimentación de todos los equipos.
Connecting to a TV without A/V Jacks
A
Conexión a un TV sin tomas de A/V
TV
TV antenna
Antena de TV
STB
RF cable
(supplied)
cable de RF
(se incluye)
Connecting to a TV with A/V Jacks
B
Conexión a un TV con tomas de A/V
TV
TV antenna
Antena de TV
STB
Audio cable
cable de audio
Video cable
cable de
video
NOTE:
•
If your TV has only one audio jack, connect the AUDIO OUT jack (L) (white) on the STB to the audio input
jack on the TV.
Si su TV sólo tiene una toma de audio, conecte la toma AUDIO OUT (L) (blanco) del STB, a la toma de entrada de audio
del TV.
10
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Cable Box (Optional)
C
Conexión a una caja de cable (opcional)
TV antenna
Antena de TV
TV
STB
Cable TV
company
empresa de
TV por cable
Audio cable
cable de audio
Video cable
Cable box ((optional)
caja dee caabblee (opciional)
cable de video
Incoming
cable signals
Señales del cable
de entrada
RF cable (supplied)
cable de RF (se incluye)
Note to the Cable TV System Installer:
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National
Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as
possible.
Observación para el instalador del sistema de cable de TV:
Este recordatorio se provee para alertar al instalador del sistema de cable de TV sobre el Artículo 820-40 del Código
Eléctrico Nacional, el cual proporciona pautas para una puesta a tierra adecuada, y en particular especifica que la puesta
a tierra del cable debe estar conectada al sistema de puesta a tierra del edificio, lo más cerca posible del punto de entrada
del cable.
11
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Other Devices
D
Conexión a otros dispositivos
TV antenna
Antena de TV
Splitter
Divisor
TV
STB
RF cable
cable de RF
Audio cable
cable de audio
DVD Recorder or VCR
Grabaddor de DDVD o videoggrabador
Audio cable
cable de audio
RF cable
(supplied)
cable de RF
(se incluye)
Video cable
cable de video
•
If your DVD recorder or VCR has only one audio jack, connect the AUDIO OUT jack (L) (white)
on the STB to the audio input jack on the DVD.
NOTE:
Si su grabador de DVD o videograbador sólo tiene una toma de audio, conecte la toma AUDIO OUT (L)
(blanco) del STB, a la toma de entrada de audio del DVD.
12
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup (Setup Wizard)
Initial Setup
Ajùste inicial
1
Press [STANDBY-ON] on the remote control to activate the STB.
Presione [STANDBY-ON] en el mando a distancia para activar el STB.
lights up in green
se vuelve verde
2
Turn on the TV, and select the viewing channel (ch3 or external input channel) on
your TV. (Refer to your TV’s manual.)
Encienda el TV, y seleccione el canal que quiera ver (canal 3 o uno de entrada externo) en su TV. (Véase el
manual del TV.)
2
1
2
CH.
CH.
Appropriate Viewing Channel
Configuración apropiada de el Canal de Visión
Viewing
STB
Cable Box
Ch3
DVD or VCR
Connection
A
(p.10)
“CH3”
External input channel
Canal de entrada externo
B
(p.10)
External input channel
C
(p.11)
(p.12)
Canal de entrada externo
External input channel
Canal de entrada externo
D
“CH3”
•
If your TV’s ch3 is already occupied, select ch4, and set the STB’s output channel to ch4. You can
switch ch3 / ch4 by holding [SETUP] down over 3 seconds.
Si el c3 de su TV ya está ocupado, seleccione el c4 y luego ajuste el canal de salida del STB a c4. Puede alternar
entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos.
”SETUP WIZARD”screen automatically appears.
Follow the directions shown on the TV screen to set the each setting.
13
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup (Setup Wizard)
7
Select “ON” or “OFF” for Daylight
Saving Time (D.S.T) using [ s / B ],
3
Select “CONTINUE” using [ s / B ],
then press [OK].
Seleccione “CONTINÚE”utilizando [s / B] y presione
then press [OK].
[OK].
Seleccione “ON”u “OFF”para la hora de verano. (D.S.T)
utilizando [s / B] y presione [OK].
This SETUP WIZARD will help you with the initial
setup on your own.
Select Daylight Saving Time.
“CONTINUE”: To continue setup
“CANCEL ”: To cancel to leave pre-arranged
setup
NOTE:
2:00AM of the second Sunday in
March until 2:00AM of the first
Sunday in November.
CANCEL
CONTINUE
4
5
Select the language using [ K / L ],
ON
OFF
then press [OK].
Seleccione el idioma utilizando [K / L] y presione [OK].
8
Select the desired display mode
using [ K / L ], then press [OK] (refer
ENGLISH Select the language for setup display.
ESPAÑOL Elija idioma de preparación.
to page 20).
FRANÇAIS Sélectionner langue écran config.
Seleccione el modo de indicación deseado utilizando
[K / L] y presione [OK].
Select display mode.
Select the connection for audio
output using [ s / B ], then press [OK].
Seleccione la conexión para salida de audio mediante
[s / B] y luego presione [OK].
LETTERBOX
ZOOM
FULL
Select the connection for Audio output.
9
Select “AUTOSCAN” using [ K / L ],
AUDIO OUT : Connecting STB and TV via AUDIO
Cable
then press [OK].
RF OUT
: Connecting STB and TV via RF
Cable
Seleccione “AUTOEXPLO.”mediante [K / L] y luego
presione [OK].
AUDIO OUT
RF OUT
The system is now scanning.
Select “AUDIO OUT” if...
- you are using the standard audio cable to
connect the STB to your TV. (Connection or
AUTOSCAN will rescan all channels.
This may take a while to complete.
B
12%
EXIT
Channel Found
EXIT
on pages 10 and 11.)
C
AUTOSCAN
Seleccione “AUDIO FUERA” si...
- está utilizando el cable de audio normal para
•
•
•
STB starts receiving available digital channels
and stores them in the channel map.
When the scanning is complete,
conectar el STB a su TV. (conexión
páginas 10 y 11.)
o
en las
B
C
Select “RF OUT” if...
“AUTOSCAN COMPLETED” will be indicated.
- you are using the RF cable to connect the STB
to your TV. (Connection or on pages 10
A
D
After autoscan is complete, use [CH K / L ]
to verify whether STB is receiving channels
properly.
and 12.)
Seleccione “RF FUERA” si...
- está utilizando el cable RF para conectar el STB a su
TV. (conexión en las páginas 10 y 12.)
o
A
D
The “SETUP WIZARD” is now complete.
El “ASISTENTE DE PREP.” ahora ha finalizado.
6
Select your time zone using [ K / L ],
then press [OK].
To cancel during scanning:
Seleccione su huso horario con [K / L] y presione [OK].
Press [SETUP] or [OK].
Select Time Zone.
Para cancelar durante la exploración: Presione [SETUP] o [OK].
ATLANTIC
EASTERN
•
If autoscan is canceled, some channels not yet
scanned may not be received. We recommend
completing autoscan.
You can do autoscan and adding / deleting
channel later. Refer to page 18.
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
•
14
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
About Sub-channel Broadcasting
Digital broadcasting offers a service that enables
multiple signals, called “sub-channels”, to be sent
simultaneously on one main channel by using its
high compression technology.
Selecting Channels on the STB
1
Enter the main channel number.
If the main channel number is 1 digit, press [ . ]
when finish entering.
ATSC
18:00
CH4-1 (Soccer)
2
Enter the sub-channel number.
If the sub-channel number is 1 digit, press [OK]
when finish entering.
18:30
(Soccer)
(News)
(Tennis)
CH4-1
CH4-2
CH4-3
E.g., selecting 6.1
19:00
CH4-1 (Soccer)
E.g., selecting 26.12
19:30
20:00
CH4-1 (Soccer)
CH4-2 (News)
: Can be changed by
using [CH K / L ].
NOTE:
•
If you do not have a particular sub-channel
number you want to select, enter the main
channel number and then press [OK]. (If the
main channel number is 1 digit, you should
press [OK] twice.) The STB automatically tunes
into the lowest sub-channel for the selected
main channel.
•
•
Press [ALT. CH] to return to the previously
viewed channel.
“NO SIGNAL” appears after the sub-channel
broadcast is over.
15
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Choosing Audio Language
You can change languages when the channel
provides alternate languages.
Press [AUDIO] repeatedly.
ENGLISH 1/4
SPANISH 2/4
FRENCH 3/4
OTHER 4/4
•
Audio language changes as follows.
•
“OTHER” is indicated when the
language is not English, Spanish
nor French.
NOTE:
•
For international stations audio
language will still be displayed as
English.
Picture Still
You can freeze the image on the TV screen.
Press [STILL].
The image on the TV screen will be paused.
To cancel still mode:
Press any button except [STANDBY-ON].
•
•
The sound output will not be
paused.
If “no signal” is detected or protected
signal is received during still mode,
the image remains paused and the
sound output will be muted.
NOTE:
•
If the TV is left on STILL for a long
period of time, the still image may
cause a burn-in effect damaging the
TV screen.
16
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Banner
The channel banner provides you with the information on the selected channel.
Press [DISPLAY].
Station name
SMILE
ABC-XXX
ENGLISH 1/2
SIGNAL 50
Program title
Channel number :
Audio language
3.1
CC
Information Icons
CC (Closed Caption):
Signal strength :
Indicates the signal strength of
the current channel.
Indicates that the program being
broadcast is available with closed
captioning.
RESTRICTED PROGRAM
TV-Y7 FV
Program ratings :
LOCK:
Displays all the available ratings.
Active ratings are highlighted in
red.
Indicates that the current program
is blocked according to your V-chip
setting.
To remove the channel banner:
Press [DISPLAY].
Electronic Program Guide (EPG)
Electronic Program Guide (EPG) is the electronic equivalent of a printed TV program guide.
You can view a list of programs scheduled for the next few hours up to the next seven days.
To display the correct information on “EPG”, “TIME ZONE”and ”D.S.T”must be set correctly.
1
Press [EPG] while watching TV.
Closed Caption :
Indicates that the program being
broadcast is available with closed
captioning.
CC
EPG
3.1
Program title
SMILE Prog 2
ABC-XXX
12:00PM-1:00PM
SMILE 2-1
SMILE 2-2
SMILE 2-3
Time segment for the program.
“NOW” icon will be displayed on
Channel number
the right for the current program.
PREV
NEXT
Indicates that there is a program
information available for next or
previous program.
Program description
2
Select the desired program using [ s / B ].
To remove the EPG:
Press [EPG].
•
•
“EPG” will be cleared after 5 minutes.
For channel numbers with blank description, the broadcasting station may not
provide signals for “EPG”.
NOTE:
•
When the program description consists of more than 4 lines, use [ K / L ] to scroll
up / down in the list.
17
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
To cancel during scanning:
Press [SETUP] or [OK].
Autoscan
(Receiving Channels)
NOTE:
Autoscan receives available digital channels and
stores them in a channel map.
•
•
If canceled, some channels not yet scanned may
not be received. We recommend completing
autoscan.
When you want to completely refresh the
channel map, delete all the channels, then do
the autoscan again. See “Adding/Deleting
Channels” on this page for details.
CAUTION:
•
If autoscan is skipped, digital channels may not
be received correctly.
1
2
Press [SETUP].
Select “CHANNEL” using [ K / L ],
then press [OK].
When “NO SIGNAL” appears on the TV screen:
Verify the antenna connection, then scan again.
The STB tunes in channel 2-1 and “NO SIGNAL”
appears if the STB could not receive any channels.
3
Select “AUTOSCAN” using [ K / L ],
then press [OK].
CHANNEL
Adding/Deleting Channels
EXIT
ADD/DELETE
CHANNEL
ANTENNA
TIME
AUTOSCAN
Add or delete desired channels in the channel map.
DETAIL
RF OUT
INITIAL
CAUTION:
•
You cannot recover the deleted channels once
they are deleted unless you perform the
autoscan again.
4
Select “AUTOSCAN” using [ K / L ],
then press [OK].
AUTOSCAN
1
2
Press [SETUP].
Select “CHANNEL” using [ K / L ],
EXIT
AUTOSCAN will rescan all channels.
This may take a while to complete.
CHANNEL
then press [OK].
TIME
BACK
AUTOSCAN
DETAIL
SETUP
INITIAL
EXIT
ADD/DELETE
CHANNEL
ANTENNA
TIME
AUTOSCAN
DETAIL
INITIAL
RF OUT
AUTOSCAN
The system is now scanning.
3
Select “ADD/ DELETE” using [ K / L ],
then press [OK].
12%
EXIT
Channel Found
CHANNEL
•
STB starts receiving available digital
channels and stores them in the channel
map.
EXIT
ADD/DELETE
CHANNEL
ANTENNA
TIME
AUTOSCAN
DETAIL
•
•
When the scanning is complete,
“AUTOSCAN COMPLETED” will be indicated.
After autoscan is complete, use [CH K / L ]
to verify whether STB is receiving channels
properly.
RF OUT
INITIAL
18
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Add
Delete
4
With “ADD” selected, enter the main
channel number you want to add,
then press [OK] or wait for a few
seconds to fix the number.
If the main channel number is 1 digit, press [0]
first.
4
5
Select “DELETE” using [ K / L ], then
press [OK].
ADD/DELETE
10.1
EXIT
ADD
10
20
26
56
CHANNEL
TIME
DELETE
DETAIL
INITIAL
NOTE:
Select the channel number you want
to delete from the channel list on the
right using [ K / L ], then press [OK].
•
Entering sub-channel number is not required.
5
Press [OK] again to add the channel
to the channel map.
E.g., deleting channel 26.
E.g., adding channel 6
ADD/DELETE
26.1
EXIT
ADD
(or leave for
a few seconds)
10
20
26
58
CHANNEL
TIME
DELETE
DETAIL
INITIAL
ADD/DELETE
6.X
ADD/DELETE
EXIT
58.1
ADD
6
10
20
58
CHANNEL
TIME
DELETE
EXIT
CHANNEL
TIME
ADD
10
20
58
60
DETAIL
INITIAL
DELETE
DETAIL
INITIAL
E.g., adding channel 26.
•
The selected channel is now deleted.
To continue deleting:
(or leave for
a few seconds)
Repeat step 5.
6
Press [SETUP] to exit.
ADD/DELETE
26.X
EXIT
CHANNEL
TIME
ADD
6
10
20
26
DELETE
DETAIL
INITIAL
•
The selected channel is now added.
To continue adding:
Repeat steps 4 and 5.
6
Press [SETUP] to exit.
19
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
Adjusting Antenna
Selecting Display Mode
You can verify the signal strength of each channel.
You can adjust the aspect ratio of the digital TV
program to fit your 4:3 TV monitor.
1
Select a channel to adjust using [the
Number buttons] or [CH K / L ].
Display Mode
2
3
Press [SETUP].
Select “CHANNEL” using [ K / L ],
then press [OK].
Select “ANTENNA” using [ K / L ],
1
2
Press [SETUP].
Select “DETAIL” using [ K / L ], then
press [OK].
4
SETUP
then press [OK].
EXIT
V-CHIP
CHANNEL
CHANNEL
CLOSED CAPTION
TIME
DISPLAY MODE
LETTERBOX
4 HOURS
EXIT
DETAIL
INITIAL
AUTO POWER DOWN
ADD/DELETE
CHANNEL
ANTENNA
TIME
ADD/DELETE
DETAIL
RF OUT
3
4
Select“DISPLAY MODE”using [ K / L ],
then press [OK].
INITIAL
•
STB starts receiving the signal for the
channel.
DETAIL
EXIT
V-CHIP
CHANNEL
CLOSED CAPTION
5
By referring to the on-screen
indication, adjust the antenna’s
direction to get the best reception.
Status bar:
Stretches to the right as the signal
strength gets stronger.
TIME
DISPLAY MODE
LETTERBOX
4 HOURS
DETAIL
INITIAL
AUTO POWER DOWN
Select the desired display mode
using [ K / L ], then press [OK].
Descriptions of each settings are explained
in the “Information on Display Mode”on the
next page.
*
ANTENNA
10.1
EXIT
WEAK
STRONG
Select display mode.
CHANNEL
TIME
NOW
10
LETTERBOX
ZOOM
50
PEAK
DETAIL
INITIAL
BACK
FULL
Peak indicator:
Indicates the highest strength ever
reached.
5
Press [SETUP] to exit.
To adjust other channels:
Select the channel using [CH K / L ], then adjust it.
6
Press [SETUP] to exit.
20
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Display Mode
Setting the Time Zone and
D.S.T (Daylight Saving Time)
LETTERBOX
16:9 picture is scaled down
until the both sides of the
picture fits the 4:3 TV. Black
bars appear on top and
bottom of the TV screen.
You need to select the time zone of your area and
set D.S.T correctly to make use of the EPG and the
Channel banner function.
ZOOM
1
2
Press [SETUP].
Select “TIME” using [ K / L ], then
press [OK].
Displays the 16:9 image with
the top and the bottom of
the picture fit to the 4:3 TV
screen. Both sides of the
picture are cut off.
Time Zone
FULL
16:9 image is squeezed into
the 4:3 TV screen. No parts
are cropped, but the picture
gets distorted.
3
Select “TIME ZONE” using [ K / L ],
then press [OK].
TIME
EXIT
EASTERN
OFF
TIME ZONE
D.S.T
CHANNEL
TIME
CAUTION:
DETAIL
INITIAL
If the TV is left in LETTER BOX mode for a long period
of time, the black bars may cause a permanent burn-
in effect.
4
5
Select your time zone using [ K / L ],
then press [OK].
Select Time Zone.
ATLANTIC
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
Press [SETUP] to exit.
21
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
4-a Enter 4-digit numbers except 4737
as your password using [the Number
buttons].
D.S.T (Daylight Saving Time)
3
4
5
Select “D.S.T” using [ K / L ], then
press [OK].
•
Enter exactly the same password again in
“Confirm password.” entry field.
TIME
EXIT
V-CHIP
EASTERN
ON
TIME ZONE
D.S.T
CHANNEL
TIME
EXIT
Enter password.
DETAIL
INITIAL
CHANNEL
Confirm password.
TIME
DETAIL
INITIAL
Select “ON” or “OFF” using [ s / B ],
then press [OK].
CAUTION:
D.S.T
Select Daylight Saving Time.
•
Do not forget the password. It will be used as
your V-chip access password from the next time
onward.
EXIT
NOTE:
2:00AM of the second Sunday in
March until 2:00AM of the first
CHANNEL
Sunday in November.
TIME
DETAIL
ON
OFF
INITIAL
4-b Enter the password using [the
Number buttons].
Press [SETUP] to exit.
•
Asterisk(*) will substitute for your password.
* * * *
V-chip Options
NOTE:
V-chip reads the ratings for programs, then denies
access to the programs which exceed the rating level
you set. With this function, you can block certain
programming inappropriate for children.
•
If you forget the password, enter “4737” then
proceed to “New Password” on page 24.
1
2
Press [SETUP].
Select “DETAIL” using [ K / L ], then
press [OK].
3
Select “V-CHIP” using [ K / L ], then
press [OK].
DETAIL
EXIT
V-CHIP
CHANNEL
CLOSED CAPTION
TIME
DISPLAY MODE
LETTERBOX
4 HOURS
DETAIL
INITIAL
AUTO POWER DOWN
•
Password entry field will appear.
If you have not created a password yet...
- proceed to step 4-a.
If you have already set a password...
- proceed to 4-b.
If you want to change the password...
- proceed to “New Password”on page 24.
22
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Select the desired rating type using
K / L ], then press [OK].
E.g., “TV RATING”
MPAA Rating
Rating
[
Description
Mature audience only
X
higher
lower
V-CHIP
NC-17
No one under 17 admitted
Restricted; under 17 requires
accompanying parent or adult
guardian
Unsuitable for children under 13
Parental guidance suggested
General audience
EXIT
CHANNEL
TIME
MPAA RATING
TV RATING
R
CANADIAN ENGLISH RATING
CANADIAN FRENCH RATING
DOWNLOADABLE RATING
CLEAR DOWNLOADABLE RATING
NEW PASSWORD
DETAIL
INITIAL
PG-13
PG
G
NR
No rating
NOTE:
•
•
“DOWNLOADABLE RATING” will be available
when the STB receives a digital broadcast which
contains V-chip 2.0 signal.
TV Rating
Rating
TV-MA
Description
If the broadcasting signal does not have the
downloadable rating information, “Downloadable
Rating is currently not available.”will appear.
This message will also appear when you try to
access “DOWNLOADABLE RATING” after you
have cleared the downloadable rating
information, and the new information has not
been downloaded since.
Mature audience only
higher
lower
Unsuitable for children under
14
TV-14
TV-PG
TV-G
Parental guidance suggested
General audience
Appropriate for all children 7
and older
TV-Y7
•
To clear the downloadable rating information
and its setting, select “CLEAR DOWNLOADABLE
RATING”.
TV-Y
Appropriate for all children
No rating
None
6
Select the desired rating using
[
K / L ], then press [OK] repeatedly
to switch between view and block.
•
When the rating is blocked, will appear.
E.g.,
“MPAA rating”
“TV rating”
V-CHIP
V-CHIP
Select MPAA rating.
Set TV rating.
EXIT
CHANNEL
TIME
EXIT
CHANNEL
TIME
X
FV
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
None
V
S
L
D
NC-17
R
PG-13
PG
G
DETAIL
INITIAL
DETAIL
INITIAL
NR
“Canadian English rating” “Canadian French rating”
V-CHIP
V-CHIP
Set Canadian English rating.
Set Canadian French rating.
EXIT
CHANNEL
TIME
EXIT
CHANNEL
TIME
18+
14+
PG
G
C8+
C
18ans+
16ans+
13ans+
8ans+
G
DETAIL
INITIAL
DETAIL
INITIAL
E
E
23
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
To Set the Sub Ratings for “TV RATING”.
7
Press [SETUP] to exit.
As for TV-MA, TV-14, TV-PG, or TV-Y7, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the step
below.
NOTE:
Use [ K / L / s / B ] to select the desired rating
or sub rating, then press [OK] repeatedly to switch
between view and block. Sub rating status will
appear beside the main rating.
•
•
When you select a rating and set it to block, the
higher ratings will be blocked automatically.
The lower ratings will be available for viewing.
When you set the highest rating to view, all
ratings will turn to view automatically.
V-CHIP
Set TV rating.
EXIT
FV
V
S
L
D
New Password
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
CHANNEL
TIME
When you forget the password or when you want
to change your password, follow the instructions
below.
DETAIL
INITIAL
None
1
2
Press [SETUP].
Select “DETAIL” using [ K / L ], then
press [OK].
Select “V-CHIP” using [ K / L ], then
press [OK].
Enter 4737 in the password entry
field.
Sub Rating
FV
Description
Fantasy Violence
Violence
Sexual Situation
Coarse Language
Suggestive Dialogue
V
S
L
D
•
3
4
5
Changing the main rating to block or view
automatically changes all its sub ratings to the
same (block or view).
Select“NEW PASSWORD” using
[ K / L ], then press [OK].
V-CHIP
Canadian English Rating
EXIT
MPAA RATING
TV RATING
Rating
Description
Adult audience only
Unsuitable for ages under 14
Parental guidance suggested
General audience
For children over 8
For all children
Exempt program
CHANNEL
TIME
CANADIAN ENGLISH RATING
CANADIAN FRENCH RATING
DOWNLOADABLE RATING
CLEAR DOWNLOADABLE RATING
NEW PASSWORD
18+
14+
PG
G
C8+
C
higher
lower
DETAIL
INITIAL
6
Enter the new 4-digit password
using [the Number buttons].
•
Enter exactly the same password again in
“Confirm password.” entry field.
E
V-CHIP
EXIT
Enter password.
Canadian French Rating
Rating Description
18 ans+ Adult audience only
16 ans + Unsuitable for ages under 16
13 ans + Unsuitable for ages under 13
CHANNEL
Confirm password.
TIME
DETAIL
INITIAL
higher
lower
7
Press [SETUP] to exit.
8 ans +
G
E
Unsuitable for ages under 8
General audience
Exempt program
24
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CC Style
Closed Caption Options
You need to set“CC STYLE”to“MANUAL”to customize
your CC style.
DTV has its own closed caption called DTV CC. Use
this menu to change the settings for DTV CC.
5
Select “MANUAL” using [ K / L ],
then press [OK].
1
2
Press [SETUP].
Select “DETAIL” using [ K / L ], then
press [OK].
CC STYLE
EXIT
CC STYLE will be displayed using
your manual setting.
CHANNEL
TIME
AUTO
3
Select “CLOSED CAPTION” using
[ K / L ], then press [OK].
DETAIL
MANUAL
DETAIL
INITIAL
If you select “AUTO”...
EXIT
V-CHIP
CHANNEL
- the original CC style set by the broadcast
station will be applied.
CLOSED CAPTION
TIME
DISPLAY MODE
LETTERBOX
4 HOURS
DETAIL
INITIAL
AUTO POWER DOWN
If you select “MANUAL”...
- you can customize the CC style as you like.
4
Select the desired closed caption
item using [ K / L ], then press [OK].
CLOSED CAPTION
CC Style Edit
You can edit the style of CC such as font, color or size,
etc. This feature is available only when “CC STYLE”is
set to “MANUAL”.
EXIT
DTV CC
OFF
5
Select an item using [ K / L ], then
press [OK]. Then use [ K / L ] to select
the desired setting and press [OK].
CHANNEL
TIME
CC STYLE
CC STYLE EDIT
AUTO
DETAIL
INITIAL
DTV CC
FONT STYLE
FONT SIZE
FONT0
MIDDLE
FONT COLOR
FONT OPACITY
BACK COLOR BLACK
BACK OPACITY SOLID
EDGE COLOR BLACK
WHITE
Digital TV has its own closed captions called DTV CC.
Use this menu to change the settings for DTV CC.
SOLID
5
Select the desired DTV closed caption
using [ K / L ], then press [OK].
Select service.
NONE
EDGE TYPE
Picture display
Back
OFF
(Back Color and Back Opacity)
SERVICE1
SERVICE2
SERVICE3
SERVICE4
SERVICE5
SERVICE6
Select if you do not want
Off
HI. EVERYONE
HI. EVERYONE
DTV CC. This is the default.
Select one of these before
Edge
DTV CC
changing any other item in
Service 1~6 “CLOSED CAPTION”menu.
Choose “SERVICE1”under
(Edge Color and Edge Type)
Font
(Font Style, Font Size, Font Color and Font Opacity)
normal circumstances.
“DTV CC”differs depending on the broadcast.
6
Press [SETUP] to exit.
25
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
Auto Power Down
“Auto power down”shuts down the STB
automatically after a certain period of time you set.
(The EPA (U.S. Environmental Protection Agency)
recommends using this setting to conserve energy.)
1
2
Press [SETUP].
Select “DETAIL” using [ K / L ], then
press [OK].
3
Select “AUTO POWER DOWN” using
[ K / L ], then press [OK].
DETAIL
EXIT
V-CHIP
CHANNEL
CLOSED CAPTION
TIME
DISPLAY MODE
LETTERBOX
4 HOURS
DETAIL
INITIAL
AUTO POWER DOWN
4
5
Select desired amount of time using
[ K / L ], then press [OK].
Select AUTO POWER DOWN time.
OFF
4 HOURS
2 HOURS
1 HOUR
•
Select “OFF” to cancel the auto power down.
Press [SETUP] to exit .
26
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Analog TV
Viendo TV Analógica
Method 1 Método 1
You can view analog TV by switching “RF OUT”setting.
Usted podrá ver TV analógica cambiando la configuración de “SALIDA RF”.
CONNECTION
CONEXIÓN
TV
STB
TV antenna
Antena de TV
RF cable (supplied)
cable de RF (se incluye)
Viewing Analog TV
Viendo TV Analógica
Viewing Digital TV
Viendo TV Digital
1
Press [STANDBY-ON] to activate the STB.
1
2
Press [STANDBY-ON] to activate the STB.
Presione [STANDBY-ON] para activar el STB.
Presione [STANDBY-ON] para activar el STB.
2
Select “RF THROUGH” in “RF OUT”
Select “CH3” in “RF OUT” menu.
(
Page 29)
menu. ( Page 29)
Seleccione “CH3” en el menú “SALIDA RF”.
Seleccione“TRAVÉS DE RF”en el menú“SALIDA RF”.
3
Select ch3 on your TV.
3
Select the desired channel on your TV.
Seleccione canal3 en su TV.
Seleccione el canal deseado en su TV.
ch3
ch4
3
2
1
H.
C
.
H
C
ch6
ch8
3
2
1
9
You can view digital TV on ch3 of your TV.
Usted podrá ver TV digital en el c3 de su TV.
.
H
C
.
H
C
4
Select desired channel on the STB.
Seleccione el canal deseado en el STB.
You can view analog TV on your TV channel.
Usted podrá ver TV analógica en su canal de TV.
ch3
ch3
NOTE:
ch3
•
You cannot view Digital TV with this setting.
With this setting, the analog TV signal can
directly be sent to your TV.
•
NOTE:
•
You cannot view Analog TV with this setting.
You can switch “RF THROUGH” to “CH3” by
holding [SET UP] down over 3 seconds.
Holding [SETUP] down over 3 seconds does
•
not switch the setting back to “RF THROUGH”.
To switch the setting back to “RF THROUGH”, follow
the steps in “Setting RF OUT” on page 29.
27
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Operation
Method 2 Método 2
You can view analog TV without switching “RF OUT”setting.
Usted podrá ver TV analógica sin cambiar la configuración de “SALIDA RF”.
CONNECTION
TV antenna
Antena de TV
TV
STB
Video cable
cable de video
Audio cable
cable de audio
RF cable (supplied)
cable de RF (se incluye)
Viewing Analog TV
Viendo TV Analógica
Viewing Digital TV
Viendo TV Digital
1
Press [STANDBY-ON] to activate the STB.
1
Press [STANDBY-ON] to activate the STB.
Presione [STANDBY-ON] para activar el STB.
Presione [STANDBY-ON] para activar el STB.
lights up in green
se vuelve verde
lights up in green
se vuelve verde
2
3
Select “RF THROUGH” in “RF OUT”
2
Select external input channel on
your TV.
menu. ( Page 29)
Seleccione el canal de entrada externo en su TV.
Seleccione“TRAVÉS DE RF”en el menú“SALIDA RF”.
Select the desired channel on your TV.
AUX
Seleccione el canal deseado en su TV.
3
2
1
.
CH
H.
C
ch4
ch6
ch8
You can view digital TV on external input
3
channel of your TV.
2
1
.
H
C
.
H
C
Usted podrá ver TV digital en el canal de entrada
externo de su TV.
3
Select desired channel on the STB.
You can view analog TV on your TV channel.
Usted podrá ver TV analógica en su canal de TV.
Seleccione el canal deseado en el STB.
AUX
AUX
AUX
28
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Appropriate “RF OUT” Setting and Viewing
Setting RF OUT
Channel
Configuración de SALIDA RF
Configuración apropiada de “SALIDA RF” y el Canal de
Visión
If you want to enjoy analog TV channels also, you
must set the “RF OUT”setting.
ANALOG TV broadcast
Transmisión de TV ANALÓGICA
Default setting is “CH3”.
Si desea disfrutar también de los canales analógicos,
Set “RF OUT” Tune your
deberá configurar la “SALIDA RF”.
setting to
TV to
La configuración por defecto es “CH3”.
Ajuste “SALIDA Sintonice su
RF” a
TV a
Connection
1
2
Press [SETUP].
Desired TV
Presione [SETUP].
Method 1 (p.27)
“RF THROUGH” channel
”TRAVÉS DE RF” Canal deseado
en su TV
Select “CHANNEL” using [K / L], then
Method 2 (p.28)
press [OK].
Seleccione “CANAL” utilizando [K / L] y presione
DIGITAL TV broadcast
Transmisión de TV DIGITAL
[OK].
Set “RF OUT” Tune your
setting to TV to
3
4
Select “RF OUT” using [K / L], then
press [OK].
Ajuste “SALIDA Sintonice su
Seleccione “SALIDA RF” utilizando [K / L]
y
RF” a
TV a
Connection
presione [OK].
Method 1 (p.27) “CH3”
Ch3
External input
Select the desired setting using
“RF THROUGH” channel
Method 2 (p.28)
[K / L], then press [OK].
”TRAVÉS DE RF” Canal de entrada
externo
Seleccione la configuración deseada utilizando
[K / L] y luego presione [OK].
•
If your TV’s ch3 is already occupied, select ch4,
and set the STB’s output channel to “CH4”.
Si el c3 de su TV ya está ocupado, seleccione el c4 y
Switch RF OUT.
If the screen doesn’t show anything
after switching RF OUT, set the TV
Channel to CH3, then hold down a
“SETUP”button for 3 seconds.
luego ajuste el canal de salida del STB a “CH4”.
RF THROUGH
CH3
CH4
Using [SETUP] to Switch “RF OUT”
Setting
Utilizando [SETUP] para cambiar la configuración
“SALIDA RF”
5
6
Using [s / B], select “YES”. Then,
press [OK].
Seleccione “SÍ” utilizando [s / B]. Luego,
RF THROUGH
over 3 seconds
presione [OK].
TRAVÉS DE RF
durante 3 segundos
RF OUT is RF THROUGH
Are you sure ?
YES
NO
If the screen doesn’t show
anything after switching
RF OUT, set the TV Channel
to CH3, then hold down a
“SETUP”button for 3 seconds.
CH3
CH4
over 3 seconds
durante 3 segundos
Press [SETUP] to exit.
Presione [SETUP] para salir.
•
You cannot switch from “CH3 /
CH4” to “RF THROUGH” with
NOTE:
[SETUP].
No podrá cambiar de “CH3 / CH4” a
“TRAVÉS DE RF” con [SETUP].
29
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
Before requesting service, check the table below for a possible cause of the problem.
Symptom
Remedy
•
Make sure that the AC power cord is securely plugged into the power
No power
outlet.
•
•
•
Make sure to point the remote control at the remote control sensor.
You may be too far from STB. Try moving closer.
Remove any obstacles between the remote control and the remote
control sensor.
Make sure that the batteries are installed in the correct direction
(+ and –). ( Page 7.)
The batteries may be depleted. Replace them with new ones.
The STB is not responding
to the remote control.
•
•
•
•
•
Make sure that the audio / video cables are correctly connected.
Make sure that the TV is turned on.
Make sure that the correct viewing channel (ch3 or external input
channel) is selected on your TV. ( Page 13.) Refer to your TV’s manual
for further information.
No audio / picture
•
•
•
•
Make sure the cables are not damaged.
Make sure “RF OUT” setting is correct. ( Page 29.)
Blocked noise on picture
Make sure that the RF cable is connected correctly. ( Pages 10 - 12.)
Make sure that “D.S.T” and “TIME ZONE” is set correctly. ( Page 21.)
No EPG or the provided
information is wrong
•
•
Sound volume differs depending on the audio out setting. Select “RF
OUT” at step 5 in the “Initial Setup (Setup Wizard)”. ( Page 14.)
Low volume
No reception
Make sure to complete autoscan in “SETUP WIZARD” or in “SETUP”
menu. When autoscan is not completed, some channels will not be
received.
The selected channel does not exist at that time. There are not always
sub-channels being broadcast.
•
•
Some channels with weak signal may not be received properly.
This is not a malfunction.
When you forget the
password for V-chip
•
If you forget the password, refer to “New Password”. ( Page 24.)
Closed captioning display
(TEXT mode) does not go
off even after changing
channels through STB.
•
•
Change the channel on your TV.
Turn the TV off, and then on.
The TV screen goes blank
just after turning the STB
on.
•
This is a normal part of the start-up process and is not a malfunction.
30
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product
DTV Digital to Analog Converter
Tuner
Receivable channels 2-69ch
Connecting Jacks
ANT. IN/OUT
RF connector x2 (75ohm)
Video Output
RCA jack x1, 1Vpp (75ohm)
Analog Audio Output
RCA jack (L / R) x2
2V rms (100k ohm)
Power Source
120V AC+/-10%, 60Hz+/-0.5%
Power Consumption
8W (Power on), Less than 1 W (Power off)
Closed Caption System
§15.122/FCC (digital CC)
Operating Condition
41°F (5°C) - 104°F (40°C)
Dimensions (W x H x D)
9.5" x 1.7" x 6"
(240mm x 43mm x 150mm)
Weight
1.4lbs. (0.6Kg)
Designs and Specifications are subject to change
without notice.
Fin
31
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date
of original retail purchase. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE
UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any
product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products
not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or
office use of this product, or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service providers without prior written
approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please
contact us at:
FUNAI SERVICE CORPORATION
Customer Service
Tel: 1-800-605-8610
5653 Creekside Parkway, Suite A, Lockbourne, OH 43137
Printed in China
X6043UD
1VMN25977 ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|