RETURN TO MAIN MENU
IM581
SAE400 WELD’N AIR - DC ARC WELDING POWER
SOURCE AND 35 CFM AIR COMPRESSOR
For use with machines having Code Number 10362
February, 2000
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built with
safety in mind. However, your overall
safety can be increased by proper
installation ... and thoughtful opera-
tion on your part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED
THROUGHOUT.
And, most importantly, think before
you act and be careful.
Date of Purchase:
Serial Number:
Code Number:
Model:
R
Where Purchased:
OPERATOR’S MANUAL
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
5.b. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating
products.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
5.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
3.j. Also see Items 6.c. and 8.
5.e. Also see item 1.b.
Mar ‘95
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
iii
SAFETY
WELDING SPARKS can
cause fire or explosion.
CYLINDER may explode
if damaged.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
7.c. Cylinders should be located:
•Away from areas where they may be struck or subjected to
physical damage.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact can
cause overheating and create a fire hazard.
•A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
FOR ELECTRICALLY
powered equipment.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits.
This can create fire hazards or overheat lifting chains or
cables until they fail.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
6.h. Also see item 1.c.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Mar ‘95
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
iv
SAFETY
WARNING
Assure that tank and compressor relief
valves work properly, and are at correct
pressure settings.
DO NOT modify or repair air tank.
NEVER move compressor with pressure in
tank.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
SAFETY
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
vi
SAFETY
PRÉCAUTIONS DE SÛRETÉ
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
Sûreté Pour Soudage A L’Arc
8. S’assurer que la masse est connectée le plus prés possible de
la zone de travail qu’il est pratique de le faire. Si on place la
masse sur la charpente de la construction ou d’autres endroits
éloignés de la zone de travail, on augmente le risque de voir
passer le courant de soudage par les chaines de levage,
câbles de grue, ou autres circuits. Cela peut provoquer des
risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher met-
allique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble de
soudage et la machine à souder en bon et sûr état defonc-
tionnement.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à soud-
er parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSA Standard
W 117.2-1974.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
b. Porter des vêtements convenables afin de protéger la peau
de soudeur et des aides contre le rayonnement de l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
Mar. ‘93
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
vii
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product •••
as much pride as we have in bringing this product to you!
Thank You
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be found
on your machine nameplate.
Model Name & Number _____________________________________
Code & Serial Number _____________________________________
Date of Purchase _____________________________________
Whenever you request replacement parts for or information on this equipment always supply the information you
have recorded above.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
viii
TABLE OF CONTENTS
Page
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section A
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Location / Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Angle of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
High Altitude Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Pre-Operation Engine and Compressor Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Compressor Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3
Engine Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4
Battery Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4
Spark Arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4
Welding Output Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-5
Machine Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-5
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section B
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Additional Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Recommended Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Welder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Auxiliary Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Compressed Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Design Features and Advantages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Duty Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Engine Controls: Function/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Welder Controls: Function/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
Auxiliary Power Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
Air Compressor Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Starting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Break-In Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Typical Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
Starting Welders with Dead Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-9
Auxiliary Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Duty Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Starting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Break-In Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section C
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section D
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section E
Wiring Diagrams and Dimension Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section F
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P303 Series, P25-L & P78-D
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
A-1
INSTALLATION
TECHNICAL SPECIFICATIONS - SAE400 WELD’N AIR
INPUT - DIESEL ENGINE
Make/Model
Description
Speed (RPM)
Displacement
Starting
System
Capacities
Perkins
4.236 Diesel
Engine
4 cylinder
63 HP @
1725 RPM
High Idle 1800
Low Idle 1100
Full Load 1725
236 cu. in
(3.87 L)
12VDC batteries
(2) & Starter
Fuel: 22.5 gal.
85.1 L
Bore x Stroke
Oil: 8.5 Qts.
8.04 L
3.875” x 5.00”
(98.4 mm x 127.0mm)
Coolant: 3.6 gal.
13.63 L
RATED OUTPUT - WELDER
Welding Output
(1)
Duty Cycle
Volts at Rated Amps
60% (NEMA)
400 amps
400 amps
36 volts
40 volts
60% (Lincoln Plus)
OUTPUT - WELDER AND GENERATOR
Welding Range
80 - 575 Amps
Open Circuit Voltage
Auxiliary Power
97 Max. OCV
@ 1800 RPM
115/230 VAC
3000 Watts, 60 Hz.
100% Duty Cycle
OUTPUT - AIR COMPRESSOR
Make/Model
Description
Delivery Tank Capacity & Rating Operating Pressure Oil Capacity
IMT
(Iowa Mold
Tooling/ Diamond
Air)
4-cylinder
35 CFM
at 100 P.S.I.
at 60%
11 Gallons
(41.6 Liters)
Loads at 95 P.S.I.
(6.7 kg/cm2)
1.33 Quarts
(1.26 Liters)
IMT’s
Synthetic
Compressor
Oil
Reciprocating,
Water Cooled,
Maximum Allowable
Working Pressure
150 PSI
Unloads at 125 P.S.I.
(1)
Pressure Lubricated Duty Cycle
(8.8 kg/cm2)
Aluminum Alloy
Block with Cast-
Iron sleeves
991 Liters/min.
Model
DA435ELW
at 7.0 kg/cm2
(10.5 kg/cm2)
PHYSICAL DIMENSIONS
HEIGHT
WIDTH
DEPTH
WEIGHT
2294 lbs.
1040.6 kg
50.13 in.
1273.3 mm
28.00 in.
83.00 in.
711.2 mm
2108.2 mm
(1)
Based on a 10 minute period.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
A-2
INSTALLATION
Read this entire installation section before you
start installation.
STACKING
SAE400 WELD’N AIR machines cannot be stacked.
SAFETY PRECAUTIONS
WARNING
ANGLE OF OPERATION
To achieve optimum engine performance the SAE400
WELD’N AIR should be run in a level position. The
maximum angle of operation for the air compressor is
20 degrees in all directions. If the compressor is to be
operated at an angle, provisions must be made for
checking and maintaining the oil level at the normal
(FULL) oil capacity in the compressor crankcase. The
maximum angle of operation for the Perkins engine is
45 degrees in all directions. If the engine is to be oper-
ated at an angle, provisions must be made for check-
ing and maintaining the oil level at the normal (FULL)
oil capacity in the engine crankcase. When operating
the welder at an angle, the effective fuel capacity will
be slightly less than the specified 22.5 gallons.
Do not attempt to use this equipment until you have
thoroughly read all operating and maintenance man-
uals supplied with your machine. They include impor-
tant safety precautions, detailed engine starting,
operating and maintenance instructions and parts
lists.
ELECTRIC SHOCK can kill.
•Do not touch electrically live parts such
as output terminals or internal wiring.
•Insulate yourself from the work and
ground.
LIFTING
•Always wear dry insulating gloves.
------------------------------------------------------------------------
The SAE400 WELD’N AIR lift bale should be used to
lift the machine.
ENGINE EXHAUST can kill.
•Use in open, well ventilated areas or
vent exhaust outside
WARNING
•Do not stack anything near the engine.
------------------------------------------------------------------------
FALLING EQUIPMENT can cause
injury.
MOVING PARTS can injure.
•Do not lift this machine using lift bale if
it is equipped with a heavy accessory
such as a trailer or gas cylinder.
•Do not operate with doors open or
guards off.
•Lift only with equipment of adequate
lifting capacity.
•Stop engine before servicing.
•Keep away from moving parts
------------------------------------------------------------------------
Only qualified personnel should install, use or service
this equipment
•Be sure machine is stable when lifting.
------------------------------------------------------------------------
LOCATION/VENTILATION
The welder should be located to provide an unrestricted
flow of clean, cool air to the cooling air inlets and to avoid
restricting the cooling air outlets. Also, locate the welder
so that the engine exhaust fumes are properly vented to
an outside area.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
A-3
INSTALLATION
HIGH ALTITUDE OPERATION
ENGINE OIL
The WELD’N AIR is shipped with the engine crankcase
filled with high quality SAE 10W-30 oil (API class CD or
better). Check the oil level before starting the engine. If it
is not up to the full mark on the dip stick, add oil as
required. Check the oil level every four hours of running
time during the first 35 running hours. Refer to the engine
Operator’s Manual for specific oil recommendations and
break-in information. The oil change interval is dependent
on the quality of the oil and the operating environment.
Refer to the engine Operator’s Manual for the proper ser-
vice and maintenance intervals.
At higher altitudes, output derating may be necessary.
As a rule of thumb, derate the welder output 5% for
every 500 meters (1640 ft.) above 1000 meters (3280
ft.).
Contact a Perkins Service Representative for any
engine adjustments that may be required for high alti-
tude operation.
TOWING
AIR COMPRESSOR OIL
The recommended trailers for use with this equipment
for in-plant and yard towing by a vehicle(1) are Lincoln’s
K767-1, K956-1 and K956-2. The K956-1 and K956-2
are also designed to be used at highway speeds(1).If the
user adapts a non-Lincoln trailer, he must assume
responsibility that the method of attachment and usage
does not result in a safety hazard nor damage the
welding equipment. Some of the factors to be consid-
ered are as follows:
The WELD’N AIR is shipped with the compressor filled
with a high quality synthetic compressor oil. If oil is
needed add only Iowa Mold Tooling Co., Inc. (IMT) syn-
thetic compressor oil until compressor is full.
CAUTION
The use of any other oil causes excessive carbon build
up, and will void the warranty on the compressor.
------------------------------------------------------------------------
Check the oil level daily. Refer to the compressor
Operator’s Manual for the proper service and mainte-
nance intervals.
1. Design capacity of trailer vs. weight of Lincoln
equipment and likely additional attachments.
2. Proper support of, and attachment to, the base of
the welding equipment so that there will be no
undue stress to the trailer’s framework.
FUEL USE DIESEL FUEL ONLY
3. Proper placement of the equipment on the trailer to
insure stability side to side and front to back when
being moved and when standing by itself.
WARNING
•Stop engine and allow to cool before
fueling.
•Do not smoke when fueling.
•Fill fuel tank at a moderate rate and do
not overfill.
4. Typical conditions of use, such as travel speed,
roughness of surface on which the trailer will be
operated, and environmental conditions.
5. Proper preventative maintenance of trailer.
•Wipe up spilled fuel and allow fumes to
clear before starting engine.
•Keep sparks and flame away from
tank.
6. Conformance with federal, state and local laws.1
(1) For highway use, consult applicable federal, state
and local laws regarding specific requirements for
use on public highways, such as brakes, lights, fend-
ers, etc.
------------------------------------------------------------------------
Fill the fuel tank with clean, fresh diesel fuel. The capac-
ity of the fuel tank is 22.5 gallons (85.1 liters). See engine
Operator’s Manual for specific fuel recommendations.
NOTE: Before starting the engine, be sure the fuel shut-
off valve on the sediment bowl is open by turning the han-
dle counterclockwise.
PRE-OPERATION ENGINE AND
COMPRESSOR SERVICE
READ the engine and compressor operating and main-
tenance instructions supplied with this machine.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
A-4
INSTALLATION
To prevent BATTERY BUCKLING, tighten nuts on bat-
teries only until snug. DO NOT OVERTIGHTEN.
ENGINE COOLING SYSTEM
The cooling system has been filled at the factory with
a 50-50 mixture of ethylene glycol antifreeze and
water. Check the radiator level and add a 50-50 solu-
tion as needed. (See Engine Manual or antifreeze con-
tainer for alternate antifreeze recommendation.)
SPARK ARRESTER
Some federal, state or local laws may require that
gasoline or diesel engines be equipped with exhaust
spark arresters when they are operated in certain loca-
tions where unarrested sparks may present a fire haz-
ard. The standard muffler included with this welder
does not qualify as a spark arrester. When required by
local regulations, a suitable spark arrester must be
installed and properly maintained.
BATTERY CONNECTION
WARNING: Use caution as the electrolyte is a strong
acid that can burn skin and damage eyes.
Remove and discard the insulating caps from the neg-
ative battery terminals. Attach and tighten negative
battery cable terminals.
CAUTION
An incorrect arrester may lead to damage to the engine
or adversely affect performance. Contact the engine
manufacturer for specific recommendations.
NOTE: This machine is furnished with wet charged
batteries; if unused for several months, the batteries
may require a booster charge. Be careful to charge the
batteries with the correct polarity. Make sure that the
batteries are level while charging.
------------------------------------------------------------------------
WARNING
GASES FROM BATTERY can explode.
● Keep sparks, flame and cigarettes
away from battery.
To prevent EXPLOSION when:
● INSTALLING A NEW BATTERY — disconnect
negative cable from old battery first and
connect to new battery last.
● CONNECTING A BATTERY CHARGER —
remove battery from welder by disconnecting
negative cable first, then positive cable and
battery clamp. When reinstalling, connect
negative cable last. Keep well ventilated.
● USING A BOOSTER — connect positive lead to
battery first then connect negative lead to neg-
ative battery lead at the lower control panel
support.
BATTERY ACID can burn eyes and
skin.
● Wear gloves and eye protection
and be careful when working near
battery.
● Follow instructions printed on battery.
IMPORTANT: To prevent ELECTRICAL DAMAGE
WHEN:
a) Installing new batteries.
b) Using a booster.
Use correct polarity — Negative Ground.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
A-5
A-5
INSTALLATION
WELDING OUTPUT CABLES
To prevent dangerous electric shock, other equipment
powered by this engine driven welder must:
With the engine off, connect the electrode and work
cables to the studs provided. These connections
should be checked periodically and tightened if neces-
sary.
a) be grounded to the frame of the welder using a
grounded type plug,
or
b) be double insulated.
Listed in Table A.1 are copper cable sizes recom-
mended for the rated current and duty cycle. Lengths
stipulated are the distance from the welder to work and
back to the welder again. Cable sizes are increased for
greater lengths primarily for the purpose of minimizing
cable voltage drop.
When this welder is mounted on a truck or trailer, its
frame must be securely connected to the metal frame
of the vehicle. When this engine driven welder is con-
nected to premises wiring such as that in a home or
shop, its frame must be connected to the system earth
ground. See the article on grounding in the latest U.S.
National Electrical Code and the local code.
Table A.1 Combined Length of Electrode and Work
Cables.
TOTAL COMBINED LENGTH OF ELEC-
TRODE AND WORK CABLES
In general, if the machine is to be grounded, it should
be connected with a #8 or larger copper wire to a solid
earth ground such as a metal water pipe going into the
ground for at least ten feet and having no insulated
joints, or to the metal framework of a building which
has been effectively grounded. The U.S. National
Electrical Code lists a number of alternate means of
grounding electrical equipment. A machine grounding
AMPS
@60%
Duty Cycle
Up to 100 100-200 FT. 200-250 FT.
FT.
400
2/0 AWG
3/0 AWG
4/0 AWG
stud marked with the
symbol is provided on the
welding generator frame foot.
MACHINE GROUNDING
Because this portable engine driven welder creates its
own power, it is not necessary to connect its frame to
an earth ground, unless the machine is connected to
premises wiring (home, shop, etc.).
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
B-1
B-1
OPERATION
OPERATING INSTRUCTIONS
GENERAL DESCRIPTION
Read and understand this entire section before operat-
ing your SAE400 WELD’N AIR.
The SAE400 WELD’N AIR is a diesel engine driven
welding power source. The machine uses a DC gen-
erator for DC stick electrode welding and an AC exciter
for 115/230 VAC auxiliary power. As a generator it can
supply up to 3,000 watts of 115/230 volt AC power. As
a welder it provides up to 575 amps of DC constant
current output. The belt driven air compressor provides
35 CFM at 100 PSI compressed air.
SAFETY INSTRUCTIONS
WARNING
Do not attempt to use this equipment until you have
thoroughly read all operating and maintenance man-
uals supplied with your machine. They include impor-
tant safety precautions, detailed engine starting, oper-
ating and maintenance instructions and parts lists.
The engine is a 63 Hp (47kw), 4-cylinder water cooled
diesel made by Perkins.
ELECTRIC SHOCK can kill.
RECOMMENDED APPLICATIONS
•Do not touch electrically live parts such
as output terminals or internal wiring.
WELDER
The SAE400 WELD’N AIR provides excellent constant
current DC welding output for stick (SMAW) welding.
The field installed optional CV Adapter (K385-1) pro-
vides up to 500 amps at 35 volts of constant voltage
output for semiautomatic welding.
•Insulate yourself from the work and
ground.
•Always wear dry insulating gloves.
------------------------------------------------------------------------
ENGINE EXHAUST can kill.
AUXILIARY POWER
•Use in open, well ventilated areas or
vent exhaust outside
The SAE400 WELD’N AIR provides 3 KW of 115/230
VAC output for auxiliary power and emergency stand-
by power.
•Do not stack anything near the engine.
------------------------------------------------------------------------
MOVING PARTS can injure.
COMPRESSED AIR
The SAE400 WELD’N AIR provides 35 CFM at 100
PSI compressed air for air arc gouging and air powered
tools.
•Do not operate with doors open or
guards off.
•Stop engine before servicing.
•Keep away from moving parts
------------------------------------------------------------------------
Only qualified personnel should operate this equipment.
ADDITIONAL SAFETY PRECAUTIONS
Always operate the welder with the hinged doors
closed as these provide maximum protection from
moving parts and insure proper cooling air flow.
Read carefully the Safety Precautions page in the
Instruction Manual before operating this machine.
Always follow these and any other safety procedures
included in this manual and in the engine and com-
pressor instruction manuals.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
B-2
OPERATION
• Gauges for engine oil pressure, coolant temperature,
battery charging ammeter, compressor air pressure
and compressor oil pressure.
DESIGN FEATURES AND ADVANTAGES
FOR STICK WELDING
• Excellent DC constant current output for stick weld-
ing applications.
• Indicator light for compressor operation.
• Engine hour meter standard.
• Continuous adjustment of both voltage and current
for unsurpassed welds on demanding jobs.
• Extended range 22.5 gallon (85.1 L) fuel tank.
DUTY CYCLE
• Remote control capability standard.
FOR AUXILIARY POWER
Duty cycle is based on a ten minute period and opera-
tion in an ambient temperature of 104°F(40°C).
• 3,000 watts of 115/230 VAC, 60 Hz auxiliary power.
• One 15 amp 115 VAC duplex receptacle for up to 26
amps of 115 VAC power.
The SAE400 WELD’N AIR is NEMA rated at 60% duty
cycle. Duty cycle is based on a ten minute period.
Therefore, a 60% duty cycle welder can be operated at
nameplate rated output for 6 minutes out of every 10
minute period without overheating.
• One 15 amp, 230 VAC duplex receptacle for up to 13
amps of 230 VAC power.
• Weld and AC auxiliary power at the same time (with-
in the limits shown on the chart below).
The auxiliary power can be used continuously (100%
duty cycle) within its rated current capacities.
Welding
Using Only
Using Only
Total
Aux.
kVA
The air compressor is rated at a 60% duty cycle based
on a ten minute period as described above.
Current, Amps 115V Circuit, 230V Circuit,
@ NEMA Arc
Volts
Amps
Amps
0
26
19.5
13
13
9.75
6.5
3.25
0
3.0
2.25
1.5
0.75
0
100
200
300
400
6.5
0
FOR COMPRESSED AIR
• 35 CFM at 100 PSI for air arc gouging and air pow-
ered tools.
• 11 Gallon air receiver tank system with integral over-
pressure relief valve for smooth air delivery.
• No welding output derating required at maximum
compressor load.
OTHER FEATURES
• Perkins 4-cylinder, water cooled diesel engine.
Designed for long life, easy maintenance and excel-
lent fuel economy.
• Engine protection system shuts the engine down for
low oil pressure or high coolant temperature.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
B-3
B-3
OPERATION
ENGINE CONTROLS
WELDER CONTROLS
IGNITION SWITCH
POLARITY SWITCH
When placed in the “ON” position, this switch energizes
the fuel solenoid. When placed in the “OFF” position,
the flow of fuel to the injection pump is stopped to shut
down the engine.
Turn the Arc Polarity switch to electrode positive or
electrode negative as required for each particular
application.
CONTROL OF WELDING CURRENT
Purpose of Controls
SPEED CONTROL LEVER
Manually allows the engine to run at its high idle speed
controlled by the governor or at the factory set low idle
speed. When welding, using air compressor or using
auxiliary power the speed control lever must be in the
“RUN” position. To reduce the engine to low idle speed
when not welding, not using the compressor or not
using auxiliary power place the speed control lever in
the “IDLE” position notch.
The continuous “Current Control” is the main current
adjuster. The “Job Selector” is both a fine current
adjuster and the continuous Open Circuit Voltage
adjuster. Open Circuit Voltage (OCV) controls the arc
characteristics.
“Job Selector”
The “Job Selector” dial is divided into four colored sec-
tions providing OCV ranges as follows:
ENGINE TEMPERATURE GAUGE
Displays the coolant temperature in the engine block.
ENGINE OIL PRESSURE GAUGE
Color
White
Black
Red
Title
Large Electrodes
Normal Welding
OCV Range
High OCV
Medium OCV
Overhead & Vertical Low OCV
Displays the oil pressure to the engine. When the
engine starts running, watch for the oil pressure to
build up. If no pressure shows within 30 seconds, stop
the engine and consult the engine instruction manual.
Grey
Special Applications Extra-Low OCV
The “Job Selector” is usually set in the black range
because it provides a soft “Buttering “ arc desired for
most welding. Some operators prefer to set the “Job
Selector” in the red range for a snappy “Digging” arc
when welding vertical up or overhead.
BATTERY CHARGING AMMETER
Displays the current going from the charging alternator
into the batteries. It is normal for charging current to be
high (above 15 amps) after starting or when the batter-
ies are ‘low’ on charge.
“Current Control”
CAUTION
Do not adjust the “Current Control” while welding
because this can damage the control.
ENGINE HOUR METER
------------------------------------------------------------------------
The “Current Control” dial is calibrated in amperes on
three separate colored dials corresponding to the
white, black and red ranges of the “Job Selector” dial.
For example: when the “Job Selector” is set on the
black range, the approximate welding current is indi-
cated on the black scale of the “Current Control” dial.
The engine hour meter records the total running time
on the engine in hours. It can be used to keep a record
of maintenance on the engine and or welder.
ENGINE PROTECTION SYSTEM
The engine protection system shuts down the engine
under high coolant temperature or low engine oil pres-
sure conditions by allowing the fuel solenoid valve to
close.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
B-4
B-4
OPERATION
How to Set the Controls
15 AMP Circuit Breakers
Assume you want a normal soft arc and about 135
amps, using a 5/32” (4.0 mm) electrode:
These circuit breakers provide separate overload cur-
rent protection for each half of the 115 V duplex recep-
tacle.The circuit breakers provide overload current pro-
tection in both current carrying wires of the 230 V
duplex receptacle.
1. Set the “Job Selector” at the center of the black
range.
2. Set the “Current Control” to read 135 amps on the
black dial.
Ground Stud
Provides a connection point for connecting the
machine to earth ground. For the safest grounding pro-
cedure refer to “Machine Grounding” in the INSTALLA-
TION section of this manual.
3. Start to weld.
4. If you want a little more current, turn the “Job
Selector” up (counterclockwise) to increase cur-
rent. If you want a little less current, turn the “Job
Selector” down (clockwise) to decrease current.
AIR COMPRESSOR CONTROLS
5. If dialing the desired current with the “Job
Selector” moves the setting outside the black
range causing undesirable arc characteristics, turn
the “Job Selector” back to the center of the black
range. Then turn the “Current Control” up or down
a little as needed. Readjust the “Job Selector” for
the exact characteristics and current desired.
COMPRESSOR ON/OFF SWITCH
Placing the “ON/OFF” switch in the “ON” position
allows the “pressure switch” (factory preset) to control
the air compressor through an electric clutch.When the
system pressure falls below 90 psi, the “pressure
switch” engages the clutch and compressor. When the
system pressure goes above 130 psi, the “pressure
switch” disengages the clutch and compressor.
REMOTE CONTROL
The “ON/OFF” switch needs to be in the “ON” position
when using compressed air. When placed in the “OFF”
position this switch does not allow the compressor
clutch to engage regardless of the tank pressure.
A receptacle and “Local/Remote” control switch on the
lower front control panel and a remote control box with
25 ft. (7.6 m) of 3-conductor cord for adjusting the OCV
at the welding site. Putting the switch in the “REMOTE”
position allows fine current control at the remote con-
trol box while placing the switch in the “LOCAL” position
allows fine current control at the “Job Selector” on the
machine. When using the optional field installed CV
adapter (K385-1) the “Local/Remote” switch is only
active in the “VV” mode.
The “ON/OFF” switch should be in the “OFF” position
while starting the engine. This will minimize the load on
the starter motor.
COMPRESSOR OPERATING LIGHT
This light is on when the compressor “ON/OFF” switch
is in the “ON” position.
AUXILIARY POWER CONTROLS
115 VAC Receptacle
COMPRESSOR AIR PRESSURE GAUGE
One 15 amp, 115 VAC duplex receptacle provides 115
VAC for auxiliary power. A total of 26 amps can be
drawn from this receptacle.
This gauge displays the air pressure in the air receiver
tanks.
230 VAC Receptacle
One 15 amp, 230 VAC duplex receptacle provides 230
VAC for auxiliary power. A total of 13 amps can be
drawn from this receptacle.
COMPRESSOR OIL PRESSURE GAUGE
This gauge displays the compressor oil pressure. Oil is
under pressure only when the compressor clutch is
engaged.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
B-5
B-5
OPERATION
BREAK-IN PERIOD
ENGINE OPERATION
CAUTION
ENGINE
Do not adjust the high idle engine speed (rpm) above
the factory setting specification as this will overspeed
the air compressor and void it’s warranty.
The engine used to supply power for your welder is a
heavy duty, industrial engine. It is designed and built
for rugged use. It is very normal for any engine to use
small quantities of oil until the break-in is accom-
plished. Check the oil level twice a day during the
break-in period (about 100 running hours).
------------------------------------------------------------------------
STARTING INSTRUCTIONS
Be sure all Pre-Operation Maintenance has been per-
formed. (See INSTALLATION section of this manual).
Set the air compressor “ON/OFF” switch in the “OFF”
position.To start the engine, set the speed control lever
in the “RUN” position. Place ignition toggle switch in
the “ON” position. Push in the engine protection sys-
tem reset button. Engage the starter button. When the
engine starts running, observe the engine oil pressure.
If no pressure shows within 30 seconds, stop the
engine and consult the engine operating manual. To
stop the engine, place the ignition toggle switch in the
“OFF” position.
IMPORTANT: IN ORDER TO ACCOMPLISH THIS
BREAK-IN, THE UNIT SHOULD BE SUBJECTED TO
HEAVY LOADS, WITHIN THE RATING OF THE
MACHINE. AVOID LONG IDLE RUNNING PERIODS.
AIR COMPRESSOR
Cylinder head stud torque must be checked after initial
8 to 10 hours of operation. See compressor operator’s
manual for details. Compressor mounting bolts should
be checked for tightness after initial 8 to 10 hours of
operation.
When an engine is started for the first time, some of the
oil will be needed to fill the passages of the lubricating
system. Therefore, on initial starting, run the engine for
about five minutes and then stop the engine and
recheck the oil. If the level is down, fill to the full mark
again.The engine controls were properly set at the fac-
tory and should require no adjusting when received.
TYPICAL FUEL CONSUMPTION
The typical fuel consumption of the SAE400 WELD’N
AIR for various operating scenarios is shown below:
Low Idle - No Load
1100 RPM
.35 gal./ hr.
(1.32 L./hr.)
For added safety always operate the welder with the
doors closed. Further, leaving the doors open changes
the designed air flow and may cause engine, generator
or compressor overheating.
High Idle - No Load
1800 RPM
.75 gal./hr.
(2.84 L./hr.)
Welding Load
400 Amps, 40 Volts
1.92 gal./hr.
(7.27 L./hr.)
Cold Weather Starting
WARNING
Auxiliary Power
3000VA
.96 gal./hr.
(3.63 L./hr.)
Never use any other starting aids, such as ether, when
using the “Thermostart” system.
Air Compressor
1.04 gal./hr.
(3.94 L./hr.)
------------------------------------------------------------------------
When overnight temperatures are between 10°F (-
12°C) and freezing, use the standard “Thermostart”
starting system installed on all engines. Follow the
instructions on the start panel nameplate and in the
engine manual shipped with the welder. With fully
charged batteries and the proper weight oil, the
“Thermostart” system operates satisfactorily even
down to about 0°F (-18°C).
400 Amps, 40 Volts Load
with Air Compressor “ON”
2.22 gal./hr.
(8.40 L./hr.)
Auxiliary Power
3000 VA with
Air Compressor “ON”
1.20 gal./hr.
(4.54 L./hr.)
If the engine must be frequently started below 10°F
(-12°C), it may be desirable to remove the
“Thermostart” and install the optional ether starter kit.
Installation and operating instructions are included in
the kit. Use ether starting only when required because
excessive use shortens engine life.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
C-1
C-1
ACCESSORIES
K799 Hi-Freq™ - Provides high frequency plus a gas
valve for TIG welding. A water valve is available as an
option. Requires 115 volt AC input. (Limited to 250A -
60% Duty Cycle).
K802-C Power Plug Kit - Kit includes male plugs for
each auxiliary receptacle.
K805-1 Ether Start Kit - Injects ether for starting aid.
Recommended only when engines are frequently
started at temperatures under 10°F (-12°C). Ether
cylinder is not included.
K767-1 Trailer - A 4-wheel steerable trailer for in-plant
and yard towing(1) with E78-14 load range (B) tubeless
tires. Mounts directly to welder base.
K956-1 and -2 Trailer - A 2-wheel trailer designed for
road(1), off road, in-plant and yard towing. The K956-2
trailer is equipped with electric brakes. Trailer mounts
directly to welder base.
1For highway use, consult applicable federal, state and local laws regarding
possible requirements for brakes, lights, fenders, etc.
Linc-Thaw™ (L2964-3) - Includes meter and fuse to
protect the welder when thawing frozen water pipes.
WARNING
Pipe Thawing IS NOT a CSA approved procedure. If
not done properly, it can result in fire, explosion,
damage to wiring which may make it unsafe, dam-
age to pipes, burning up the welder or other haz-
ards.
IMPORTANT: DO NOT USE A WELDER TO THAW
A PIPE BEFORE REVIEWING LINCOLN BULLETIN
E695.1 (dated October 1987 or later). This bulletin
may be obtained from your local Lincoln distributor or
by writing directly to Lincoln Electric at the address on
the back of this manual.
K704 Standard Accessory Kit - Includes electrode
and work cables, headshield, work clamp and elec-
trode holder.
K385-1 CV Adapter - Provides constant voltage output
for semiautomatic welding. (Field installation only).
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
D-1
MAINTENANCE
Note: Water and fuel should be drained into a suit-
WARNING
able container for proper disposal.
ELECTRIC SHOCK can kill.
COMPRESSOR AIR RECEIVER TANKS
● Do not touch electrically live parts
such as output terminals or inter-
nal wiring
Drain the condensation from the tanks after each use
by opening the drain valve located at the lower right
rear of the welder.
ENGINE EXHAUST can kill.
ENGINE AIR FILTER
● Use in open, well ventilated areas
The engine air filter element is a dry cartridge type. It
is located above the engine. It can be cleaned and re-
used; however, damaged elements should not be
washed or re-used. Remove loose dirt from element
with compressed air or water hose directed from inside
out. Compressed Air: 100 psi maximum. The filter
should never be removed while the engine is running.
or vent exhaust outside
MOVING PARTS can injure.
● Do not operate with doors open or
guards off
● Stop engine before servicing
PERIODIC MAINTENANCE
● Keep away from moving parts
1. Blow out the welder and controls with an air hose at least
once every two months. In particularly dirty locations, this
cleaning may be necessary once a week. Use low pres-
sure air to avoid driving dirt into the insulation.
● Remove guards only when necessary and
replace when work requiring removal is com-
plete.
● Only qualified personnel should install, use, or
service this equipment.
2. The current control reactor brushes are self-lubricating
and should not be greased. Keep the contacts clean. This
control should be moved from maximum to minimum daily
to prevent the controls from sticking.
ROUTINE MAINTENANCE
At the end of each day’s welding, refill the fuel tank to
minimize moisture condensation in the tank. Also, run-
ning out of fuel tends to draw dirt into the fuel system.
Check the engine crankcase and compressor oil levels.
3. See the engine Instruction Manual for periodic engine
maintenance information. Change the crankcase oil at
regular intervals using the proper grade of oil as recom-
mended in the engine operating manual. Change the oil
filter in accordance with the instructions in the engine
operating manual. When the oil filter is changed add one
quart of oil to the crankcase to replace the oil held in the
filter during operation.
If the fuel supply runs out while the fuel pump is oper-
ating, air may be entrapped in the fuel distribution sys-
tem. If this happens, bleeding of the fuel system may
be necessary. See the engine instruction manual.
FUEL SYSTEM WATER SEPARATOR
MAINTENANCE
4. See the compressor operator’s manual for periodic com-
pressor maintenance information. Change the compres-
sor oil at regular intervals using only Iowa Mold Tooling
Co., Inc. (IMT) synthetic compressor oil as recommended
in the compressor operating manual.
If the fuel system on the engine is equipped with a
water separator, the following maintenance proce-
dures must be followed.
Inspect the glass bowl for any accumulation of water
on a daily basis. If water is present:
CAUTION
The use of any other oil causes excessive carbon build up,
and will void the warranty on the compressor.
--------------------------------------------------------------------------------
1. Insure the fuel shut off valve is in the "open" position.
2. Loosen the drain screw on the bottom of the bowl
one to two turns or until water begins to flow. Do
not remove the screw completely.
3. Drain until the water has visibly drained from the
bowl and only clear fuel starts to flow from the
drain valve.
5. Belts tend to loosen after the first 30 or 40 hours of oper-
ation. Check the cooling fan belt and tighten if necessary.
DO NOT OVER TIGHTEN. The compressor belt does not
require any adjustment.
4. Close the drain screw tightly by hand.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
D-2
MAINTENANCE
between slip rings and brushes with the coarse side
against the brushes. With slight additional finger pres-
sure on top of the brushes, pull the sandpaper around
the circumference of the rings, in direction of rotation
only - until brushes seat properly. In addition, stone
slip ring with a fine stone. Brushes must be seated
100%. Arcing or excessive exciter brush wear indicates
a possible misaligned shaft. Have an authorized Field
Service Shop check and realign the shaft.
BEARING MAINTENANCE
This welder is equipped with a double-shielded ball bearing
having sufficient grease to last indefinitely under normal ser-
vice. Where the welder is used constantly or in excessively
dirty locations, it may be necessary to add one-half ounce of
grease per year. A pad of grease one inch wide, one inch
long and one inch high weighs approximately one-half
ounce. Over greasing is far worse than insufficient greasing.
When greasing the bearings, keep all dirt out of the area.
Wipe the fittings completely clean and use clean equipment.
More bearing failures are caused by dirt introduced during
greasing than from insufficient grease.
COOLING SYSTEM
The SAE400 WELD’N AIR is equipped with a pressure
radiator. Keep the radiator cap tight to prevent loss of
coolant. Clean and flush the cooling system periodi-
cally to prevent clogging the passage and overheating
the engine. When antifreeze is needed, always use the
permanent type.
COMMUTATOR AND BRUSH MAINTENANCE
WARNING
Uncovered rotating equipment can be dangerous.
Use care so your hands, hair, clothing or tools do
not catch in the rotating parts. Protect yourself
from particles that may be thrown out by the rotat-
ing armature when stoning the commutator.
------------------------------------------------------------------------
The generator brushes are properly adjusted when the
welder is shipped. They require no particular attention.
DO NOT SHIFT THE BRUSHES or adjust the rocker
setting.
ENGINE AND COMPRESSOR MAINTENANCE
COMPONENTS
ITEM
Engine Air Filter
Fan Belt
MAKE
Donaldson
Lincoln
Gates
PART NUMBER
P181052
S19730
8129
Compressor Belt
Lincoln
Gates
S23887
2/A40
Fuel Filter
Engine Oil Filter
Perkins
Perkins
26561117
2654403
Shifting of the brushes may result in:
- Change in machine output
- Commutator Damage
- Excessive brush wear
REPLACING AIR COMPRESSOR DRIVE BELT
Periodically inspect the commutator, slip rings and
brushes by removing the covers. DO NOT remove or
replace these covers while the machine is running.
CAUTION
Belt is tensioned using a automatic tensioning device.
Remove with care.
Commutators and slip rings require little attention.
However, if they are black or appear uneven, have
them cleaned by an experienced maintenance man
using fine sandpaper or a commutator stone. Never
use emery cloth or paper for this purpose.
------------------------------------------------------------------------
To remove compressor belt:
1. Remove nut and lock washer from lower locking
bolt on idler tension flange.
2. Loosen center mounting bolt on idler tensioner 1/2
turn or until it moves freely.
NOTE: If the welder is used in dirty or dusty locations,
or if the welder is not used for prolonged periods of
time, it may be necessary to clean the commutator and
slip rings more often.
3. Using a pipe wrench or equivalent tool, turn ten-
sioner body slightly to free locking bolt. Remove
locking bolt and slowly release tension on belt.
Remove belt.
Replace brushes when they wear within 1/4" of the pig-
tail. A complete set of replacement brushes should be
kept on hand. Lincoln brushes have a curved face to fit
the commutator. Have an experienced maintenance
man seat these brushes by lightly stoning the commu-
tator as the armature rotates at full speed until contact
is made across the full face of the brushes.
After stoning, blow out the dust with low pressure air.
Note: Do not loosen or remove compressor mounting
bolts. Pulley misalignment may result.
To install belt (after following above procedure):
1. Mount belt into pulley grooves and over idler pul-
ley.
2. Using a pipe wrench or suitable tool, turn idler
body to realign locking slot in idler flange with lock-
ing hole. Insert locking bolt and tighten before
releasing idler body. Tighten center mounting bolt.
Note: Ensure that both belt strands are running prop-
erly in pulley grooves.
To seat the slip ring brushes, position the brushes in
place. Then slide one end of a piece of fine sandpaper
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
E-1
E-1
TROUBLESHOOTING
HOW TO USE TROUBLESHOOTING GUIDE
WARNING
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician
and machine operator and will invalidate your factory warranty. For your safety and to avoid
Electrical Shock, please observe all safety notes and precautions detailed throughout this
manual.
__________________________________________________________________________
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM
(SYMPTOMS)”. This column describes pos-
sible symptoms that the machine may exhib-
it. Find the listing that best describes the
symptom that the machine is exhibiting.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE
CAUSE” lists the obvious external possibili-
ties that may contribute to the machine
symptom.
For Air Compressor trouble shooting see the
air compressor operator’s manual.
For Engine trouble shooting see the engine
operator’s guide.
For Generator trouble shooting follow this
guide.
This Troubleshooting Guide is provided to
help you locate and repair possible machine
malfunctions. Simply follow the three-step
procedure listed.
Step 3. RECOMMENDED COURSE OF
ACTION
This column provides a course of action for
the Possible Cause.
If you do not understand or are unable to
perform the Recommended Course of
Action safely, contact you local Lincoln
Authorized Field Service Facility.
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts such as output
terminals or internal wiring.
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or vent exhaust
outside.
MOVING PARTS can injure.
• Do not operate with doors open or guards off.
• Stop engine before servicing.
• Keep away from moving parts.
• Remove guards only when necessary and replace when work
requiring removal is complete.
• Only qualified personnel should install, use or service this
equipment.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local
Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2
E-2
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
RECOMMENDED
COURSE OF ACTION
POSSIBLE CAUSE
FUNCTION PROBLEMS
Machine fails to hold the “heat”
constantly.
Rough or dirty commutator.
True and clean commutator.
Brushes may be worn down to limit Replace brushes.
of life.
Brush springs may be broken.
Replace brush springs.
Field circuit may have variable resis- Check field current with ammeter to
tance connections or intermittent
open circuit, due to loose connec-
tions or broken wire.
discover varying current. This
applies to both the main generator
and exciter.
Electrode or work lead connections Tighten all connections.
may be poor.
Wrong grade of brushes may be
installed on generator.
Use only the recommended Lincoln
brushes.
Field rheostat may be making poor Inspect and clean rheostat.
contact and overheating.
“Current Control” may not be operat- Check for loose or missing set screw
ing properly.
in control handles.
“Current Control” brushholder con- Inspect. Replace needed parts.
tact springs may be worn out or
missing. Contact surface may be
dirty, rough and pitted.
Clean internal contact surface of
control device. Do not lubricate.
Smooth rough surfaces.
“Current Control” brushholder sup- If brushholder internal contact sur-
port stud and mating contact sur-
faces may be dirty or pitted and
burned.
face is pitted and burned, replace
the brushholder and support stud. If
the contact surface is dirty, clean off
the brushholder stud and internal
contact surface. Apply mixture of
three parts silicone grease and one
part zinc powder (by weight) to stud.
Engine running at varying speeds.
Set welder controls for maximum
output and weld. Then, while weld-
ing, check engine rpm. The engine
should be running at full speed. If
indicator shows a significant differ-
ence, consult your engine manual.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local
Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
E-3
E-3
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
RECOMMENDED
COURSE OF ACTION
POSSIBLE CAUSE
FUNCTION PROBLEMS
Welder runs but fails to generate
current.
Generator or exciter brushes may be Be sure that all brushes bear on the
loose or missing.
commutator and have proper spring
tension.
Exciter may not be operating.
Check exciter output voltage with
voltmeter or lamp.
Field circuit of generator or exciter
may be open.
Check for open circuits in rheostat,
field leads and field coils. Also check
resistors.
Polarity reversing switch may be in Put handle in positive or negative
the neutral position.
position.
Exciter may have lost excitation.
Check components and continuity in
flashing circuit.
Welding arc is loud and spatters
excessively.
Series field circuit may be open cir- Check circuit with ringer or volt-
cuited.
meter.
Current setting may be too high.
Check setting and current output
with ammeter.
Polarity may be wrong.
Check polarity. Try reversing polarity
or try an electrode of the opposite
polarity.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local
Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
E-4
E-4
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
RECOMMENDED
COURSE OF ACTION
POSSIBLE CAUSE
FUNCTION PROBLEMS
Welding current too great or too
“Current Control” shaft and handle
With current control against the min-
small compared to indication on the may have turned slightly in the insu- imum stop, set pointer to within 1/8”
dial.
lated bushing of the current control of the last scale division.
brushholder, caused by turning han-
dle too hard against one of the
stops.
Exciter output low causing low out- Check for shorts in exciter armature
put compared to dial indication.
with growler.
“Current Control” set to minimum
and welder output so great that
engine stalls when arc is struck.
Check to see that series field is
properly connected and not shorted.
Welder has output and no control
Local/Remote switch is in wrong
position.
Place switch in “LOCAL” position to
control output at the welder. Place
switch in “REMOTE” position to con-
trol output remotely.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local
Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
E-5
E-5
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
RECOMMENDED
COURSE OF ACTION
POSSIBLE CAUSE
FUNCTION PROBLEMS
No auxiliary power
Circuit Breakers open.
Check and reset breakers. If breakers
keep tripping check connections to
auxiliary receptacles. Also make sure
load does nor exceed receptacle’s
current rating.
Faulty connections to auxiliary
receptacles.
Check connections.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local
Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
F-1
F-1
WIRING DIAGRAMS
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
F-2
F-2
WIRING DIAGRAMS
+
+
+
+
+
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
F-3
F-3
DIMENSION PRINT
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
Now Available...12th Edition
New Lessons in Arc Welding
The Procedure Handbook of Arc Welding
Lessons, simply written, cover manipulatory techniques;
machine and electrode characteristics; related subjects, such
as distortion; and supplemental information on arc welding
applications, speeds and costs. Practice materials, exercises,
questions and answers are suggested for each
lesson.
With over 500,000 copies of previous editions published
since 1933, the Procedure Handbook is considered by many to
be the “Bible” of the arc welding industry.
This printing will go fast so don’t delay. Place your
order now using the coupon below.
528 pages, well illustrated, 6” x 9” size, bound in simulated,
gold embossed leather.
The hardbound book contains over 750 pages of welding infor-
mation, techniques and procedures. Much of this material
has never been included in any other book.
$5.00 postage paid U.S.A. Mainland
A
must for all welders, supervisors, engineers and
designers. Many welding instructors will want to use the book as
a reference for all students by taking advantage of the low quan-
tity
discount
prices
which
include
shipping
by
4th class parcel post.
$15.00 postage paid U.S.A. Mainland
Need Welding Training?
The Lincoln Electric Company operates the oldest and
most respected Arc Welding School in the United States at its
corporate headquarters in Cleveland, Ohio. Over 100,000 students
have graduated. Tuition is low and the training is
“hands on”
How To Read Shop Drawings
The book contains the latest information and application
data on the American Welding Society Standard Welding
Symbols. Detailed discussion tells how engineers and drafts-
men use the “short-cut” language of symbols to pass on
assembly and welding information to shop personnel.
For details write:
Lincoln Welding School
22801 St. Clair Ave.
Cleveland, Ohio 44117-1199.
Practical exercises and examples develop the reader’s ability
to visualize mechanically drawn objects as they will appear in
their assembled form.
and ask for bulletin ED-80 or call 216-383-2259 and ask for the
Welding School Registrar.
187 pages with more than 100 illustrations. Size 8-1/2” x 11”
Durable, cloth-covered board binding.
Lincoln Welding School
BASIC COURSE
5 weeks of fundamentals
$700.00
$4.50 postage paid U.S.A. Mainland
There is a 10% discount on all orders of $50.00 or more for shipment at one time to one location.
Orders of $50 or less before discount or orders outside of North America must be prepaid with charge, check or money order in U.S. Funds Only.
Prices include shipment by 4thClass Book Rate for U.S.A. Mainland Only. Please allow up to 4 weeks for delivery.
UPS Shipping for North America Only. All prepaid orders that request UPS shipment please add:
$5.00
For order value up to $49.99
$10.00
$15.00
For order value between $50.00 & $99.99
For order value between $100.00 & $149.00
For North America invoiced orders over $50.00 & credit card orders, if UPS is requested, it will be invoiced or charged to you at cost.
Outside U.S.A. Mainland order must be prepaid in U.S. Funds. Please add $2.00 per book for surface mail or $15.00 per book for air parcel post shipment.
METHOD OF PAYMENT: (Sorry, No C.O.D. Orders)
CHECK ONE:
Name:
_______________________________________________
Address: _______________________________________________
_______________________________________________
Please Invoice (only if order is over $50.00)
Check or Money Order Enclosed, U.S. Funds only
Credit Card -
Telephone: _______________________________________________
MasterCard
VISA
®
®
Signature as it appears on Charge Card:
|_|_| |_|_|
Account No.
|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|
Exp Date
______________________
Month
Year
USE THIS FORM TO ORDER:
BOOKS OR FREE INFORMATIVE CATALOGS
Order from: BOOK DIVISION, The Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199
Telephone: 216-383-2211 or, for fastest service, FAX this completed form to: 216-361-5901.
Lincoln Welding School
Titles:
Price
$5.00
$15.00
$4.50
$5.00
Code
L
PH
H
IM
Quantity
Cost
(ED-80)
New Lessons in Arc Welding
Procedure Handbook “Twelfth Edition”
How to Read Shop Drawings
Incentive Management
A New Approach to Industrial Economics $5.00
The American Century of John C. Lincoln $5.00
Seminar Information
(ED-45)
Educational Video Information
(ED-93)
NA
AC
James F. Lincoln Arc Welding
Foundation Book Information
Welding Preheat Calculator
Pipe Welding Charts
$3.00
$4.50
WC-8
ED-89
(JFLF-515)
SUB TOTAL
Additional Shipping Costs if any
TOTAL COST
Download from Www.Somanuals.com. All Manuals Search And Download.
● Do not touch electrically live parts or ● Keep flammable materials away.
● Wear eye, ear and body protection.
electrode with skin or wet clothing.
● Insulate yourself from work and
ground.
WARNING
Spanish
● No toque las partes o los electrodos ● Mantenga el material combustible
● Protéjase los ojos, los oídos y el
bajo carga con la piel o ropa moja-
da.
● Aislese del trabajo y de la tierra.
fuera del área de trabajo.
cuerpo.
AVISO DE
PRECAUCION
French
● Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
● Gardez à l’écart de tout matériel
inflammable.
● Protégez vos yeux, vos oreilles et
votre corps.
ATTENTION
● Isolez-vous du travail et de la terre.
German
● Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
● Isolieren Sie sich von den
● Entfernen Sie brennbarres Material! ● Tragen Sie Augen-, Ohren- und Kör-
perschutz!
WARNUNG
Elektroden und dem Erdboden!
Portuguese
● Não toque partes elétricas e elec-
trodos com a pele ou roupa molha-
da.
● Mantenha inflamáveis bem guarda- ● Use proteção para a vista, ouvido e
dos.
corpo.
ATENÇÃO
● Isole-se da peça e terra.
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO
BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-
STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
● Keep your head out of fumes.
● Use ventilation or exhaust to
remove fumes from breathing zone.
● Turn power off before servicing.
● Do not operate with panel open or
guards off.
WARNING
Spanish
● Los humos fuera de la zona de res-
piración.
● Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
● Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
● No operar con panel abierto o
guardas quitadas.
AVISO DE
PRECAUCION
French
● N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
● Gardez la tête à l’écart des fumées. ● Débranchez le courant avant l’entre-
● Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
tien.
ATTENTION
German
● Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
● Vermeiden Sie das Einatmen von
Schweibrauch!
● Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
● Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öff-
nen; Maschine anhalten!)
WARNUNG
Portuguese
● Não opere com as tampas removidas.
● Desligue a corrente antes de fazer
serviço.
● Mantenha-se afastado das partes
moventes.
● Não opere com os paineis abertos
ou guardas removidas.
● Mantenha seu rosto da fumaça.
● Use ventilação e exhaustão para
remover fumo da zona respiratória.
ATENÇÃO
● Não toque as partes elétricas nuas.
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
SAE400 WELD’N AIR
Download from Www.Somanuals.com. All Manuals Search And Download.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|