Kidde Smoke Alarm PI9000 User Manual

SIGNALING  
U
L
LISTED  
Sm o ke Ala rm  
Users Guide  
Model: i9030, i9040, i9040RV i9050, i9060,  
i9060RV a n d i9080  
i9040  
a n d  
i9040RV  
i9030  
i9060  
a n d  
i9050  
i9080  
i9060RV  
• 9 Volt Battery Operated  
ATTENTION: Please take a few minutes to thoroughly read this  
users guide w hich should be saved for future reference and  
passed on to any subsequent ow ner.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual P/N 820-1493 Rev. A  
Pro d u ct Sp e cifica t io n s  
1. Re co m m e n d e d Lo ca t io n s fo r Sm o ke Ala rm s  
This alarm detects products of combustion using the ionization tech-  
nique. It contains 0.9 microcurie of Americium 241, a radioactive materi-  
al (see section 9). Distributed under U.S. NRC License No. 32-23858-01E.  
Manufactured in compliance with U.S. NRC safety criteria in 10 CFR  
32.27. The purchaser is exempt from any regulatory requirements. Do  
not try to repair the smoke alarm yourself. Refer to the instructions in  
section 12 for service.  
Locate the first alarm in the immediate  
area of the sleeping rooms. Try to monitor  
the exit path as the sleeping rooms are  
usually farthest from the exit. If more than  
one sleeping area exists, locate additional  
alarms in each sleeping area (See figure 3).  
Locate additional alarms to monitor any  
stairway as stairways act like chimneys for  
smoke and heat.  
LOSS OF POWER TO THE ALARM WILL RENDER THIS ALARM  
INOPERATIVE.  
FIGURE 1  
Locate at least one alarm on every floor  
level.  
Locate an alarm in every sleeping room.  
Co n t e n t s o f Th is Use rs Gu id e  
Locate an alarm in every room where elec-  
trical appliances are operated (i.e. portable  
heaters or humidifiers).  
1. Recommended Locations for Smoke Alarms  
2. Locations to avoid  
Locate an alarm in every room where  
someone sleeps with the door closed. The  
closed door may prevent an alarm not  
located in that room from waking the  
3. Installation Instructions  
4. Operation and testing  
5. Nuisance Alarms  
sleeper.  
FIGURE2
6. Maintenance  
Smoke, heat, and combustion products  
rise to the ceiling and spread horizontally.  
Mounting the smoke alarm on the ceiling  
in the center of the room places it closest  
to all points in the room. Ceiling mount-  
ing is preferred in ordinary residential con-  
struction.  
7. Limitations of Smoke Alarms  
8. Good Safety Habits  
9. NRC Information  
10. NFPA Protection Standard 72  
11. California State Fire Marshal Required Information  
12. Service and Warranty  
For mobile home installation, select loca-  
tions carefully to avoid thermal barriers  
that may form at the ceiling. For more  
details, see MOBILE HOME INSTALLATION  
below.  
When mounting an alarm on the ceiling,  
locate it at a minimum of 4” (10 cm) from  
the side wall (see figure 1).  
FIGURE 3  
ANYWHERE ALONG  
THIS BOLD SURFACE  
When mounting the alarm on the wall, use  
an inside wall with the top edge of the  
alarm at a minimum of 4” (10 cm) and a  
maximum of 12” (30.5 cm) below the ceil-  
ing (see figure 1).  
12”  
(300mm)  
FIGURE 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Re co m m e n d e d Lo ca t io n s fo r Sm o ke Ala rm s  
2. Lo ca t io n s To Avo id  
In the garage. Products of combustion are present when you start  
your automobile.  
Put smoke alarms at both ends of a hallway or large room if the hall-  
way or room is more than 30 ft (9.1 m) long. For large rooms, one  
smoke alarm is recommended for every 500 square feet of floor  
space.  
Less than 4” (10cm) from the peak of an “A” frame type ceiling.  
In an area where the temperature may fall below 40ºF or rise above  
100ºF, such as garages and unfinished attics; this should also include  
electrical boxes exposed to these environments.  
In homes that are not well insulated, extreme heat or cold can be  
transferred from the outside to the inside through poorly insulated  
walls and roof. This may create a thermal barrier which can prevent  
the smoke from reaching an alarm mounted on the ceiling. If you are  
not sure about the insulation in your home, or if you notice that the  
outer walls and ceiling are either hot or cold, install the alarm on an  
inside wall. In such homes, install the smoke alarm with the top edge  
of the alarm at a minimum of 4” (10 cm) and a maximum of 12”  
(30.5 cm) below the ceiling (see figure 1).  
In dusty areas. Dust particles may cause nuisance alarm or failure to  
alarm.  
In very humid areas. Moisture or steam can cause nuisance alarms.  
In insect-infested areas.  
Smoke alarms should not be installed within 3 ft (.9m) of the following:  
the door to a kitchen, the door to a bathroom containing a tub or  
shower, forced air supply ducts used for heating or cooling, ceiling or  
whole house ventilating fans, or other high air flow areas.  
Install Smoke Alarms on sloped, peaked or cathedral ceilings at or  
within 3ft (0.9m) of the highest point (measured horizontally). NFPA  
72 states: “Smoke alarms in rooms with ceiling slopes greater than 1  
ft in 8 ft (.3m in 2.4 m) horizontally shall be located on the high side  
of the room.” NFPA 72 states: “A row of detectors shall be spaced  
and located within 3 ft (0.9m) of the peak of the ceiling measured  
horizontally” (see figure 2).  
Kitchens. Normal cooking may cause nuisance alarms. If a kitchen  
alarm is desired, it should have an alarm silence feature or be a photo-  
electric type.  
Near fluorescent lights. Electronic “noise” may cause nuisance alarms.  
Smoke alarms are not to be used with detector guards unless the  
combination (alarm and guard) has been evaluated and found suitable  
for that purpose.  
Install Smoke Alarms on tray-shaped ceilings (coffered ceilings) on the  
highest portion of the ceiling or on the sloped portion of the ceiling  
within 12” (305mm) vertically down from the highest point (see figure  
4).  
Mobile Home Installation  
Modern mobile homes have been designed and built to be energy effi-  
cient. Install smoke alarms as recommended above (refer to RECOM-  
MENDED LOCATIONS and Figures 1 and 2). In older mobile homes that  
are not well insulated compared to present standards, extreme heat or  
cold can be transferred from the outside to the inside through poorly  
insulated walls and roof. This may create a thermal barrier which can  
prevent the smoke from reaching an alarm mounted on the ceiling. In  
such units, install the smoke alarm on an inside wall with the top edge  
of the alarm at a minimum of 4” (10cm) and a maximum of 12”  
(30.5cm) below the ceiling (see figure 1).  
If you are not sure about the insulation in your mobile home, or if you  
notice that the outer walls and ceiling are either hot or cold, install the  
alarm on an inside wall. For minimum protection, install at least one  
alarm close to the sleeping rooms. For additional protection, see SINGLE  
FLOOR PLAN in figure 2.  
WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER RV  
OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE  
EACH TRIP AND AT LEAST ONCE A WEEK DURING USE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. In st a lla t io n In st ru ct io n s  
3. In st a lla t io n In st ru ct io n s  
MOUNTING INSTRUCTIONS  
CAUTION: This unit is sealed. The cover is not removable!  
O
1. Remove the mounting plate from the back of the alarm by holding the  
mounting plate and twisting the alarm in the direction indicated by the  
OFF” arrow on the alarm cover.  
A
A
2. To insure aesthetic alignment of the alarm with the hallway or wall, the  
A” line on the mounting plate should be parallel with the hallway when  
ceiling mounting or horizontal when wall mounting.  
mounting  
i9030 mounting  
bracket for all  
3. After selecting the proper smoke alarm location as described in section 1,  
attach the mounting plate to the ceiling as shown in figure 5 and figure  
5A. For wall mounting see figure 6 and figure 6A. Place mounting plate  
on the wall as described in the mounting illustrations. Use the screws  
and anchors provided to secure the mounting plate (use 3/16” drill bit for  
anchor holes).  
bracket shown  
other models  
FIGURE 5  
FIGURE 5A  
FIGURE 6  
The “A” line should be hori-  
zontal and the “UP FOR  
WALL MOUNTING” arrow  
must be pointing up.  
4. Battery installation instructions are provided on the inside of the battery  
door. To ensure proper installation of the smoke alarm battery, follow  
the instructions.  
5. When installing the battery, press the battery reminder finger down into  
the battery compartment and install the battery (see figure 7 and figure  
7A for the i9080 alarm).  
5º  
CAUTION! IF THE BATTERY REMINDER FINGER IS NOT HELD DOWN IN  
THE BATTERY COMPARTMENT BY THE BATTERY, THE BATTERY DOOR  
WILL NOT CLOSE AND THE UNIT WILL NOT ATTACH TO THE MOUNT-  
ING BRACKET. NOTE: THE I9030 AND I9040 DO NOT HAVE A BATTERY  
DOOR.  
FIGURE 6A  
FIGURE 7  
FIGURE 7A  
When wall mounting,  
mount flat side to the  
wall and rotate mount-  
ing plate approximately  
5º to the right as shown.  
6. Alignment marks are provided on the edge of the trim plate and the  
alarm. After installing the mounting plate, place the alarm on the  
mounting plate with the alignment marks lined up. Twist the alarm in the  
direction indicated by the “ONarrow on the alarm cover (see figure 8)  
until it locks in place.  
7. USING TAMPER RESIST LOCKING PIN (all models except i9040 and  
i9040RV): To make your smoke alarm tamper resistant, a locking pin has  
been provided in the bag with the screws and anchors. Using this pin will  
help deter children and others from removing the alarm from the mount-  
ing plate. To use the pin, insert it into the hole in the side of the alarm  
after the alarm has been installed on the mounting plate (see figure 9).  
Alignment marks  
Remove  
Install  
NOTE: THE TAMPER RESIST PIN WILL HAVE TO BE REMOVED IN  
ORDER TO CHANGE THE BATTERIES. USE LONG NOSE PLIERS TO PULL  
THE PIN OUT OF THE HOLE. IT IS NOW POSSIBLE TO REMOVE THE  
ALARM FROM THE MOUNTING PLATE.  
8. After installation, test your alarm by depressing and holding down the  
test button for at least 5 seconds. This should sound the alarm.  
FIGURE 8  
FIGURE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Op e ra t io n a n d Te st in g  
5. Nu isa n ce Ala rm s  
OPERATION: The smoke alarm is operating once a fresh battery is  
installed and testing is complete. When products of combustion are  
sensed, the unit sounds a loud 85db pulsating alarm until the air is  
cleared.  
Smoke alarms are designed to minimize nuisance alarms. Cigarette  
smoke will not normally set off the alarm, unless the smoke is blown  
directly into the alarm. Combustion particles from cooking may set off  
the alarm if the alarm is located close to the cooking area. Large quanti-  
ties of combustible particles are generated from spills or when broiling.  
Using the fan on a range hood which vents to the outside (non-recircu-  
lating type) will also help remove these combustible products from the  
kitchen. If the alarm does sound, check for fires first. If a fire is discov-  
ered, get out and call the fire department. If no fire is present, check to  
see if one of the reasons listed in section 2 may have caused the alarm.  
HUSH CONTROL: The “HUSH” feature has the capability of temporarily  
desensitizing the alarm circuit for approximately 8 minutes. This feature  
is to be used only when a known alarm condition, such as smoke from  
cooking, activates the alarm. Models i9060, i9060RV and i9080 are  
desensitized by pushing the “HUSH” button on the smoke alarm cover.  
Models i9030, i9040, i9040RV and i9050 are desensitized by pushing  
the TEST/HUSH button on the cover. If the smoke is not too dense, the  
alarm will silence immediately and the Red LED will flash once every 10  
seconds for approximately 8 minutes. This indicates that the alarm is in a  
temporarily desensitized condition. The smoke alarm will automatically  
reset after approximately 8 minutes and sound the alarm if particles of  
combustion are still present. The “HUSH” feature can be used repeated-  
ly until the air has been cleared of the condition causing the alarm.  
6. Ma in t e n a n ce  
BATTERY REPLACEMENT  
Note: Replacement batteries are available where you purchased your  
alarm.  
If tamper resist pin has been used, refer to TAMPER RESIST LOCKING PIN  
in section 3 for removal instructions. To replace the battery, remove the  
alarm from the mounting plate by rotating the alarm in the direction of  
the “OFF” arrow on the cover (see figure 8).  
NOTE: DENSE SMOKE WILL OVERRIDE THE HUSH CONTROL FEA-  
TURE AND SOUND A CONTINUOUS ALARM.  
CAUTION: BEFORE USING THE ALARM HUSH FEATURE, IDENTIFY  
THE SOURCE OF THE SMOKE AND BE CERTAIN A SAFE CONDITION  
EXISTS.  
i9030, i9040, i9050, i9060 and i9080 Smoke Alarms are powered by a  
9V carbon zinc battery (alkaline and lithium batteries may also be used).  
A fresh battery should last for one year under normal operating condi-  
tions. This alarm has a low battery monitor circuit which will cause the  
alarm to “chirp” Approximately every 30 - 40 seconds for a minimum  
of seven (7) days when the battery gets low. Replace the battery when  
this condition occurs.  
FLASHING LED LIGHT: This smoke alarm is equipped with a flashing  
red indicator light. The light is located under the test button and will  
flash every 40 seconds to indicate that the smoke alarm is receiving  
power.  
TESTING: Test by pushing the test button on the cover and holding it  
down for a minimum of 5 seconds. This will sound the alarm if the elec-  
tronic circuitry, horn, and battery are working. If no alarm sounds, the  
unit has defective batteries or other failure. DO NOT use an open flame  
to test your alarm, you could damage the alarm or ignite combustible  
materials and start a structure fire.  
NOTE: ANY STATEMENTS REFERRING TO A BATTERY, APPLIES TO  
BOTH BATTERIES USED WITH THE i9080  
USE ONLY THE FOLLOWING 9 VOLT BATTERIES FOR SMOKE ALARM  
BATTERY REPLACEMENT.  
Carbon-zinc type:  
Alkaline type:  
EVEREADY 1222; GOLD PEAK 1604P OR 1604S  
TEST THE ALARM WEEKLY TO ENSURE PROPER OPERATION.  
ENERGIZER 522; DURACELL MN1604, MX1604;  
GOLD PEAK 1604A; PANASONIC 6AM6, 6AM-6,  
6AM-6PI, 6AM6X, AND 6LR61(GA)  
Erratic or low sound coming from your alarm may indicate a defective  
alarm, and it should be returned for service (see section 12).  
NOTE: WEEKLY TESTING IS REQUIRED.  
Lithium type:  
ULTRALIFE U9VL-J  
Models i9040RV and i9060RV are powered by a 9V alkaline battery.  
A
fresh battery should last for one year under normal operating conditions.  
This alarm has a low battery monitor circuit which will cause the alarm  
to “chirp” approximately every 30 - 40 seconds for a minimum of seven  
(7) days when the battery gets low. Replace the battery when this condi-  
tion occurs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Ma in t e n a n ce  
6. Ma in t e n a n ce  
USE ONLY THE FOLLOWING 9 VOLT BATTERIES FOR i9040RV AND  
i9060RV SMOKE ALARM BATTERY REPLACEMENT:  
lamp holder assembly. Slide the old lamp out of the lamp holder and  
replace it with a new lamp. Replace with the correct lamp type: Vanco  
#FTB 6 which is available at most radio/tv repair stores.  
Alkaline type:  
ENERGIZER 522; DURACELL MN1604, MX1604;  
PANASONIC 6AM6, 6AM-6, 6AM-6PI, 6AM6X,  
AND 6LR61(GA)  
Reinstall the lamp holder. It will snap easily into the base. Put working  
batteries back in the alarm and remount the alarm on its mounting  
bracket.  
NOTE: WEEKLY TESTING IS REQUIRED.  
CAUTION: Use only the lamp specified. Use of a different lamp  
may have a detrimental effect on the smoke alarm or the safety  
light operation.  
WARNING! USE ONLY THE BATTERIES SPECIFIED. USE OF DIFFER-  
ENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE  
SMOKE ALARM.  
NOTE: The safety light is not intended to satisfy the requirements  
for approved illumination under various local codes. Very thick  
and/or dense smoke may obscure the light.  
CLEANING YOUR ALARM  
YOUR ALARM SHOULD BE CLEANED AT LEAST ONCE A YEAR  
To clean your alarm, remove it from the mounting bracket as outlined in  
the beginning of this section. You can clean the interior of your alarm  
7. Lim it a t io n s o f Sm o ke Ala rm s  
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY  
(sensing chamber) by using compressed air or a vacuum cleaner hose  
and blowing or vacuuming through the openings around the perimeter  
of the alarm. The outside of the alarm can be wiped with a damp cloth.  
NFPA 72 states: Fire-warning equipment for residential occupancies  
are capable of protecting about half of the occupants in potentially  
fatal fires. Victims are often intimate with the fire, too old or too  
young, or physically or mentally impaired such that they cannot  
escape even when warned early enough that escape should be possi-  
ble. For these people, other strategies such as protection-in-place or  
assisted escape or rescue would be necessary.  
After cleaning, reinstall your alarm and test your alarm by using the test  
button. If cleaning does not restore the alarm to normal operation the  
alarm should be replaced.  
SAFETY LIGHT  
MODEL i9080  
Smoke alarms are devices that can provide early warning of possible  
fires at a reasonable cost; however, alarms have sensing limitations.  
Ionization sensing alarms may detect invisible fire particles (associated  
with fast flaming fires) sooner than photoelectric alarms. Photoelectric  
sensing alarms may detect visible fire particles (associated with slow  
smoldering fires) sooner than ionization alarms. Home fires develop in  
different ways and are often unpredictable. For maximum protection,  
Kidde recommends that both Ionization and Photoelectric alarms be  
installed.  
NOTE: If the safety light appears dim during regular testing, replace  
both batteries immediately. Use only the following 9 volt batteries for  
powering the safety light:  
Alkaline Type  
Energizer 522  
Duracell MN1604 or MX1604  
Gold Peak 1604A  
Panasonic 6AM6, 6AM-6, 6AM-6PI, 6AM6X and  
6LR61 (GA)  
A battery powered alarm must have a battery of the specified type, in  
good condition and installed properly.  
The safety light has a 6.3 V 250mA fuse lamp with an average life of 50  
hours. If the safety light fails to operate with a fresh alkaline battery,  
then replace the lamp. To replace the lamp, remove the alarm from the  
mounting bracket by rotating the alarm in the direction of the “OFF”  
arrow on the cover (See Figure 7, and Alarm Tamper Resist Feature sec-  
tion if this feature has been activated).  
AC powered alarms (without battery backup) will not operate if the  
AC power has been cut off, such as by an electrical fire or an open  
fuse.  
Smoke alarms must be tested regularly to make sure the batteries and  
the alarm circuits are in good operating condition.  
Smoke alarms cannot provide an alarm if smoke does not reach the  
alarm. Therefore, smoke alarms may not sense fires starting in chim-  
neys, walls, on roofs, on the other side of a closed door or on a differ-  
ent floor.  
Open the battery door and remove both batteries from the unit. Grip  
the lamp holder handle with your thumb and finger and pull out the  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Lim it a t io n s o f Sm o ke Ala rm s  
8. Go o d Sa fe t y Ha b it s  
- Fires where the victim is intimate with a flaming initiated fire; for  
example, when a person's clothes catch fire while cooking.  
If the alarm is located outside the sleeping room or on a different  
floor, it may not wake up a sound sleeper.  
- Fires where the smoke is prevented from reaching the detector due  
to a closed door or other obstruction.  
The use of alcohol or drugs may also impair ones ability to hear the  
smoke alarm. For maximum protection, a smoke alarm should be  
installed in each sleeping area on every level of a home.  
- Incendiary fires where the fire grows so rapidly that an occupant's  
egress is blocked even with properly located detectors  
Although smoke alarms can help save lives by providing an early  
warning of a fire, they are not a substitute for an insurance policy.  
Home owners and renters should have adequate insurance to protect  
their lives and property.  
9. NRC In fo rm a t io n  
Ionization type smoke alarms use a very small amount of a radioactive ele-  
ment in the sensing chamber to enable detection of visible and invisible  
combustion products. The radioactive element is safely contained in the  
chamber and requires no adjustments or maintenance. This smoke alarm  
meets or exceeds all government standards. It is manufactured and distrib-  
uted under license from the U.S. Nuclear Regulatory Commission.  
8. Go o d Sa fe t y Ha b it s  
DEVELOP AND PRACTICE A PLAN OF ESCAPE  
Make a floor plan indicating all doors and windows and at least two  
(2) escape routes from each room. Second story windows may need a  
rope or chain ladder.  
10. NFPA Re q u ire d Pro t e ct io n  
Have a family meeting and discuss your escape plan, showing every-  
one what to do in case of fire.  
The National Fire Protection Associations Standard 72 provides the following  
information:  
Determine a place outside your home where you all can meet if a fire  
occurs.  
Smoke Detection - Where required by applicable laws, codes, or standards  
for a specific type of occupancy, approved single- and multiple-station  
smoke alarms shall be installed as follows:  
Familiarize everyone with the sound of the smoke alarm and train  
them to leave your home when they hear it  
(1) In all sleeping rooms and guest rooms  
Practice a fire drill at least every six months, including fire drills at  
night. Ensure that small children hear the alarm and wake when it  
sounds. They must wake up in order to execute the escape plan.  
Practice allows all occupants to test your plan before an emergency.  
You may not be able to reach your children. It is important they know  
what to do.  
(2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft)  
of any door to a sleeping room, the distance measured along a path of travel  
(3) On every level of a dwelling unit, including basements  
(4) On every level of a residential board and care occupancy (small facility),  
including basements and excluding crawl spaces and unfinished attics  
Install and maintain fire extinguishers on every level of the home and  
in the kitchen, basement and garage. Know how to use a fire extin-  
guisher prior to an emergency.  
(5) In the living area(s) of a guest suite  
(6) In the living area(s) of a residential board and care occupancy (small facility)  
• Current studies have shown smoke alarms may not awaken all sleep-  
ing individuals, and that it is the responsibility of individuals in the  
household that are capable of assisting others to provide assistance to  
those who may not be awakened by the alarm sound, or to those  
who may be incapable of safely evacuating the area unassisted.  
Are More Smoke Alarms Desirable? The required number of smoke alarms  
might not provide reliable early warning protection for those areas separated  
by a door from the areas protected by the required smoke alarms. For this  
reason, the use of additional smoke alarms for those areas for increased pro-  
tection is recommended. The additional areas include the basement, bed-  
rooms, dining room, furnace room, utility room, and hallways not protected  
by the required smoke alarms. The installation of smoke alarms in kitchens,  
attics (finished or unfinished), or garages is not normally recommended,  
because these locations occasionally experience conditions that can result in  
improper operation.  
There are situations where a smoke alarm may not be effective to pro-  
tect against fire as noted by the NFPA and UL. For instance:  
- Smoking in bed.  
- Leaving children unsupervised.  
- Cleaning with flammable liquids, such as gasoline.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. CAUTION (AS REQUIRED BY THE CALIFORNIA  
STATE FIRE MARSHAL)  
12. Se rvice a n d Wa rra n t y  
If after reviewing this manual you feel that your smoke alarm is defective  
in any way, do not tamper with the unit.  
Ionization type smoke alarms use a very small amount of a radioac-  
tive element in the sensing chamber to enable detection of visible  
and invisible combustion products. The radioactive element is safely  
contained in the chamber and requires no adjustments or mainte-  
nance. This smoke alarm meets or exceeds all government stan-  
dards. It is manufactured and distributed under license from the U.S.  
Nuclear Regulatory Commission.  
Return for servicing to: KIDDE Safety, 1016 Corporate Park Dr., Mebane,  
NC 27302. 800-880-6788 (See Warranty for in-warranty returns)  
LIMITED WARRANTY  
Kidde warrants to the original purchaser that the enclosed smoke alarm will  
be free from defects in material and workmanship or design under normal  
use and service for a period of three (3) years for i9030, i9040 and  
i9040RV smoke alarms and ten (10) years for the i9050, i9060,  
i9060RV, and i9080 smoke alarms from the date of purchase. The obli-  
gation of Kidde under this warranty is limited to repairing or replacing the  
smoke alarm or any part which we find to be defective in material, work-  
manship or design, free of charge to the customer, upon sending the  
smoke alarm with proof of date of purchase, postage and return postage  
prepaid, to Warranty Service Department, Kidde, 1016 Corporate Park Dr.,  
Mebane, NC 27302.  
This warranty shall not apply to the smoke alarm if it has been damaged,  
modified, abused or altered after the date of purchase or if it fails to oper-  
ate due to improper maintenance or inadequate AC or DC electrical power.  
THE LIABILITY OF KIDDE OR ANY OF ITS PARENT OR SUBSIDIARY CORPO-  
RATIONS ARISING FROM THE SALE OF THIS SMOKE ALARM OR UNDER  
THE TERMS OF THIS LIMITED WARRANTY SHALL NOT IN ANY CASE  
EXCEED THE COST OF REPLACEMENT OF SMOKE ALARM AND, IN NO  
CASE, SHALL KIDDE OR ANY OF ITS PARENT OR SUBSIDIARY CORPORA-  
TIONS BE LIABLE FOR CONSEQUENTIAL LOSS OR DAMAGES RESULTING  
FROM THE FAILURE OF THE SMOKE ALARM OR FOR BREACH OF THIS OR  
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR  
DAMAGE IS CAUSED BY THE COMPANY’S NEGLIGENCE OR FAULT.  
Since some states do not allow limitations on the duration of an implied  
warranty or do not allow the exclusion or limitation of incidental or conse-  
quential damages, the above limitations or exclusions may not apply to  
you. While this warranty gives you specific legal rights, you may also have  
other rights which vary from state to state.  
The above warranty may not be altered except in writing signed by both  
parties hereto.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUESTIONS OR FOR MORE INFORMATION  
Call our Consumer Hotline at 1-800-880-6788 or contact  
us at our website at w w w.kidde.com  
Kidde, 1016 Corporate Park Drive, Mebane, NC 27302  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Electric Pressure Cooker IT50E1 S User Manual
Intel Computer Drive SSDSA2SH064G1C5 User Manual
John Deere Lawn Mower X700 User Manual
JVC Camcorder D 9 User Manual
Keating Of Chicago Fryer 14 BB Gas User Manual
Kenwood Stereo Amplifier KAC 8403 User Manual
Keys Fitness Home Gym KPS 2250 User Manual
Kidde Smoke Alarm i9010 User Manual
Kobe Range Hoods Ventilation Hood RA9436SQF User Manual
Korg Musical Instrument EMX 1 User Manual