Power Supply Preparations
Other Play Methods
Basic Play
Intro play
Program play
Repeat play
Using dry-cell batteries
(not supplied)
Using the AC adaptor (not supplied)
Follow the steps in the numerical order.
You can successively play the first 10 seconds of every track.
You can program up to 32 tracks in any desired order including You can repeat one track or all tracks.
the same tracks.
3
Track number in play
During playback,
1
While stopped,
HOLD
AC power outlet
1
While stopped,
OFF
ON
ALL
AC adaptor
INTRO
MODE
MODE
5
0102 53
PROG
PROGRAM
(Repeatedly)
To cancel
(Repeatedly)
0001
1 track repeat
All track repeat
• Play stops automatically
when all the tracks have
been played.
Two “LR6” alkaline batteries.
Elapsed playing time of
each track
4
2
Track number to be programmed
00: Not programmed yet.
Press MODE repeatedly until the repeat indicator goes out.
Caution:
Program sequence
number
VOLUME
Do not forcibly open the battery lid too wide.
Notes:
Battery indicator
2 Select the desired track.
• You can also select Repeat play during Program play.
• You can also select Repeat play while stopped.
1
Battery indicator
To cancel
Firmly connect
Press MODE repeatedly until “INTRO” goes out.
PROG
Label side
Hyper-Bass Sound effect
6
0301
2
Notes:
You can enjoy powerful bass sound.
VOLUME
R
L
• You can also select Intro play during playback.
In this case, Intro play will start from the next track after the
current track has finished.
HBS 1
OFF
1
2
HBS
e.g. Track number 3
• You can also select Intro play during Program play mode.
This indicator appears when the batteries are almost out of power.
Power will be cut off a short while later.
Notes:
3
• Even if the unit is turned off, small power is consumed as long
as the AC adaptor is connected to the AC power outlet.
• When you want to purchase the AC adaptor, see page 5.
Random play
PROG
Note:
Anti-Shock Protection EX
PROGRAM
During playback,
Turning off the Anti-Shock Protection EX will save the battery power
more or less. For details, see “Anti-shock Protection EX” on page 4.
0002
This function achieves excellent performance against sound inter-
ruption caused by vibrations. You will be able to enjoy listening
to music during (not vigorous) jogging.
By utilizing the high-performance servo circuit, audio data will be
stored in the memory ahead of time (up to 45 seconds worth).
Normally, this function is in effect.
For your reference:
“dISC”
This indication appears if 3/8 is pressed when no disc is loaded
or if the disc is not properly seated.
Operation
Button
Display/reference
RAND
MODE
Next program sequence number
During play,
(Repeatedly)
The track is registered.
To pause
“– –”
0700 18
After playing all tracks, the unit stops.
Preparation period before playing the track
Flashes for several seconds after pressing 3/8 to play.
Press again to restart play.
During play,
4
5
Repeat steps 2 and 3.
To cancel
When you program exceeding 32 tracks, the program se-
quence number returns to “01” and will overwrite the previ-
ous setting.
Total number of tracks
ANTI SHOCK
“OPEn”
Press MODE until “RAND” goes out, or press 7 to stop the disc.
ANTI
indicator
SHOCK
This indication appears when the lid is open.
Notes:
As the audio data is gradually stored, the indicator changes as follows:
To stop
Removing discs
Turn off the unit and, after the disc has stopped rotating, remove
the disc as shown below:
• You can also select Random play in stop mode.
• During Program play, you can not select Random play.
1044 48
Preventing Accidental Operation (Hold mode)
This function causes the unit to ignore, accidental button presses. • When the unit is in Hold mode, “HoLd” and “
follows.
Hold mode prevents the following:
• Powering on the unit accidentally (which can cause the batter-
ies to go dead).
Total playing time.
[Fully stored]
” lights as
While stopped,
No indication
To cancel
Power on : “
Power off : “HoLd” and “
” stays lit.
To turn off the
unit
• To confirm the program
” lights up for a few seconds
A.S.P
While stopped, press PROGRAM repeatedly. At this time, you
can change the program, if required.
when 6 is pressed.
• Play being cut off unexpectedly.
The “ANTI SHOCK” indicator goes out.
Note:
Skip function
During play,
• To skip back to the previous track, quickly press 4
twice.
• During Program play, the button is used to fast for-
ward or back through the programmed sequence of
tracks.
• During Random play, the skip button cannot be used
to skip back to tracks that were played previously in
the random sequence.
To use the Hold mode
• To delete the entire program
Turn off the unit.
If the HOLD switch is set to the ON position, you cannot turn on
the unit.
To activate again
Press the ASP button.
Reverse
Auto power off
Fast forward/
reverse
If the unit is left in stop mode for 30 seconds, the unit turns
itself off automatically to prevent the batteries from running
down.
Notes:
Forward
• To prevent the unit from powering on accidentally, set the
HOLD switch to the ON position while the unit is turned off.
• To prevent the unit from unexpected operation during play,
set the HOLD switch to the ON position after you starts play-
ing the disc.
• During this operation, the disc rotates at a higher rate than usual
in order to collect extra audio data. This may cause the batteries
to run out faster and could result in a slight increase in disc rota-
tion noise.
• This function can be switched ON and OFF during playback.
However, this may cause a slight interruption in the sound be-
cause the disc’s rotational speed changes.
Search function
Keep depressed during play.
Disc rotation noise
The portable CD player uses a power-saving operation method
so that disc rotation noise will intermittently be emitted. But, it
is not a failure.
2
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|