JVC Car Video System LVT1774 001A User Manual

HDD NAVIGATION/DVD RECEIVER

NAVEGACIÓN HDD/RECEPTOR DVD

SYSTÈME DE NAVIGATION À DISQUE DUR/RÉCEPTEUR DVD

KD-NXD505

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

For customer Use:

Enter below the Model

No. and Serial No. which

are located on the top or

bottom of the cabinet.

Retain this information

for future reference.

INSTRUCTIONS

Model No.

Serial No.

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

LVT1774-001A

[J]

Download from Www.Somanuals.com. All Manuals Search And Download.

Hard Disk Drive (HDD)

WARNINGS:

To prevent accidents and damage

Installation

• DO NOT install any unit in locations

where:

This unit has a built-in HDD, which is a device

to read minute magnetic changes. The inside of

the device is precision components, requiring

you to notice the following when installing the

unit:

Install the unit at a place where the following

conditions are satisfied:

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

– it may obstruct visibility.

• Dry and neither too hot nor too cold—

between 5°C (41°F) and 35°C (95°F).

If the temperature is too low, the HDD will

not work. Wait until the temperature in the

car becomes normal before operating the

unit.

• At an altitude between –300 m (–980 ft) below

sea level and +3000 m (9800 ft) above sea

level.

• DO NOT operate the unit while driving. If

you need to operate the unit while driving,

be sure to look ahead carefully.

• The driver must not watch the monitor

while driving.

• If the parking brake is not engaged,

“

Parking Brake” flashes on the monitor,

and no playback picture will be shown.

– This warning appears only when the

parking brake wire is connected to the

parking brake system built in the car

(refer to the Installation/Connection

Manual).

• With adequate ventilation to prevent internal

heat buildup in the unit.

Before using HDD

While the unit is turned on, the hard disk

is constantly rotating at a high speed. This

requires you to notice the following:

• DO NOT impart vibration or shock.

• DO NOT allow anything having strong

magnetism or emitting strong electromagnetic

waves (cellular phones, etc.) near the unit.

• DO NOT disconnect the power cords from

the car battery when the unit is turned on.

Failure in following the above cautions may

damage the HDD (the stored data will be lost

and be never restored).

This unit does not function properly unless

the speed signal lead is connected (refer to the

Installation/Connection Manual).

When the temperature is low, the HDD may

take some time to start up, or may reboot

automatically.

It should be noted that it may be unlawful to

re-record pre-recorded tapes, records, or discs

without the consent of the owner of copyright

in the sound or video recording, broadcast or

cable programme and in any literary, dramatic,

musical, or artistic work embodied therein.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to reset your unit

How to forcibly eject a disc

If a disc cannot be recognized by the unit or

cannot be ejected, eject the disc as follows.

• Your preset adjustments

will also be erased.

[Hold]

Emergency Eject and No Eject (or Eject

OK) appear on the monitor.

Press 5 / ∞ repeatedly to select Emergency

Eject, then press ENT.

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

How to detach/attach the control panel

Detaching

Attaching

Download from Www.Somanuals.com. All Manuals Search And Download.

INFORMATION (For U.S.A.)

Cautions on the monitor:

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in

a residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

• The monitor built in this unit has been

produced with high precision, but it may

have some ineffective dots. This is inevitable

and is not malfunction.

• Do not expose the monitor to direct

sunlight.

For safety...

• Do not raise the volume level too much, as

this will block outside sounds, making driving

dangerous.

• Stop the car before performing any

complicated operations.

Temperature inside the car...

– Reorient or relocate the receiving antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in

the car becomes normal before operating the

unit.

– Consult the dealer or an experienced radio/

TV technician for help.

Caution on volume setting:

Discs produce very little noise compared with

other sources. Lower the volume before playing

a disc to avoid damaging the speakers by the

sudden increase of the output level.

This product incorporates copyright

protection technology that is protected

by U.S. patents and other intellectual

property rights. Use of this copyright

protection technology must be authorized

by Macrovision, and is intended for home

and other limited viewing uses only unless

otherwise authorized by Macrovision.

Reverse engineering or disassembly is

prohibited.

[European Union only]

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

8 Introduction

Initial settings

Basic operations

Parts index

Remote controller—RM-RK250

18 Navigation system

Basic operations

Registering your home

Starting guidance

Searching for a place

How you are guided

Arranging your route

Registering favorite points

Traffic information on map

Navigation menu items

Download from Www.Somanuals.com. All Manuals Search And Download.

51 Radio

Listening to the radio

Listening to the satellite radio

59 Discs and HDD

Disc operations

Music server operations

CD changer operations

79 Other functions

iPod/D. player operations

Playing other external components

Using Bluetooth devices

AV Menu items

Sound equalization

109 Troubleshooting

117 Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial settings

When you turn on the unit for the first time, the initial setup screen appears. Follow the procedure

below and make necessary settings.

Turn on the power.

Language

English US

Español

Français

Adjust the following settings.

DST

Select an item

Select Auto if your residential area is

subject to DST (Daylight Saving Time).

Proceed to the next setting

Reverse Polarization

Engage the parking brake, step on the

brake pedal, then switch the gear lever.

If Forward and Reverse alternates

on the display, connection is correct.

Select one of the alternatives (GND or

Battery) that shows the gear position

correctly.

Back to the previous setting

Language

Select the language you want for the

display and the voice guidance.

Store Display Mode

Select Off

• If you select On, the System starts in

the navigation demonstration mode

for shops. (☞ [47])

Finish the procedure.

Installation Angle

Select which angle your unit is installed

at. This setting is necessary for the

precise functioning of the Navigation

System.

• See “Measuring the installation

angle” on the Installation/Connection

Manual.

You can also change these settings (except

Store Display Mode) through Setup

Menu and AV Menu when necessary.

•

Language ☞ [46]

Installation Angle ☞ [46]

Time Zone ☞ [91]

DST ☞ [91]

Reverse Polarization ☞ [94]

Time Zone

Select your residential area for clock

adjustment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Calibration

Before using the Navigation System first time, it is required to calibrate the Navigation System.

• After deleting the calibration data (☞ [46] Reset Calibration) or changing the installation

angle (☞ [46] Installation Angle), calibration is also required.

1 Display the map screen.

2 Display the detail screen and check the

connections.

[Hold]

Calibrating...

Detail

GPS Antenna

Sensor Status

Learning Lv.

GPS Antenna

Speed Signal

Parking Brake :Off

Direction

:OK [5]

:12.0

•

OK ] Connection is OK. ([5]: number of the GPS

satellites whose signal is detected.)

•

NG ] Antenna is disconnected or short-circuited.

:Forward

Speed Signal

Calibrating...

Drive the car for a while.

• If the number increases as you speed up the car,

connection is OK.

: Calibration not in

progress.

Parking Brake

Step on the brake pedal, then disengage and engage the

parking brake repeatedly.

: Calibration in progress.

• If Off appears when disengaged and On appears when engaged, connection is OK.

If the result is not good, check the connection.

• You can see detailed information on the items of Sensor Status in Information

Connection. (☞ [43])

]

3 After confirming all the above connections, drive the car to start

calibration.

• This process can take five minutes or more depending on the average speed driven.

• A certain speed (greater than 25 mi/h (40 km/h)) is required for calibration.

• Calibration time differs among the cars.

• During calibrating, you can use the AV functions of the unit (you can listen to the music,

etc.)

• If you turn off the ignition switch, calibration is temporarily stopped. When it is turned

on, calibration will restart.

Once calibration is finished, the arrowhead icon turns red and the current position information

appears instead of Calibrating...

Learning Lv. (maximum level is

) reaches

after

calibration finished.

Navigation (functions such as guidance or route simulation) cannot be used until calibration

is complete.

Initial settings

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

Reset the unit.

• Use only when the internal

system malfunctions.

To turn on the power

To change the source

TUNER

EXT-IN/iPod/D. PLAYER*

= (Back to the beginning)

* You cannot select these sources if they are not

ready.

SAT*

DISC*

HDD

Bluetooth Audio*

CD-CH/

To turn off the power

[Hold]

To turn off the AV function

To drop the volume in a moment (ATT)

[Hold]

The display switches to the map screen.

• To activate the AV function, press the

button briefly.

ATT indicator flashes.

To restore the sound, press the same

button again.

To adjust the volume

For navigation operations, ☞ [18]

For radio operations, ☞ [51]

For disc/HDD operations, ☞ [59]

For Bluetooth operations, ☞ [83]

For other sources, ☞ [79]

Download from Www.Somanuals.com. All Manuals Search And Download.

To switch between the map screen and AV

screen

AV screen

FM1

AV screen

Map screen

Station name

92.5 MHz

You can always switch between the AV

screen and the map screen.

This switching does not affect the playback

sound of the unit (except while recording an

Audio CD) or the guidance function of the

Navigation System.

Distance to the next turn/Turn

icon

(While not guided: Speed/

Direction)

(

☞ [35])

Current time

The built-in clock is automatically adjusted by

receiving the GPS signals.

To change the display of AV screens

Vehicle information

Video input

AV screen 1

AV screen 2

(☞ [82])

The number and contents of AV screens depend on the source.

** Appears only when you have selected Videoor Camerafor Video Inputsetting (☞ [93]).

How to change the control panel angle

[Hold]

Tilt 1

Tilt 2

Tilt 3

Tilt 4

Caution: Do not insert your finger behind the control panel.

Basic operations 11

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

To call up a menu

Navigation Menus

AV Menu

Map screen

AV screen

FM1

Station name

92.5 MHz

Destination Menu ☞ [42]

AV Menu ☞ [90]

Destination

Home

1/2

AV Menu

Setup

1/2

Return

Address

Vicinity

Sound

Screen Control

Aspect

• The display indications may change according

to change of the specifications.

Information Menu ☞ [42]

Information

Current Position

1/2

Traffic

Turns List

Trip

To navigate through menus

Press: Select a menu item

Hold: Skip to the first menu

item on the next page

Destination

Proceed to the next menu

Back to the previous menu

Setup Menu ☞ [43]

Setup

1/2

Guidance Voice

Guidance Options

Route Options

Map Color

To go back to the previous screen

and adjust other items:

Map Options

To cancel menu operations and

return to the map screen or the AV

screen:

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu screen

When the current menu has

multiple pages, the current

page number and total page

number, for example “1/3”,

will be displayed here.

Current menu title

Remaining time until the

menu screen goes off.

(Appears only on AV Menu.)

Display

Language

Wall Paper

Scroll

Tag Display

Dimmer

Selected menu item

Button icons indicate the

available operations in

each screen.

Current setting of the

selected item.

[English US]

On some screens, special operations are indicated

here with the button to use.

Menu items

Ex.:

Delete

: Button to press

•

If items are displayed in gray, you

cannot use them now.

: Button to press and hold

When no icon is displayed here, ENT button

functions the same as button.

•

In this manual, operation of selecting a menu item is instructed as in the example below.

Ex.:

AV Menu

]

Pop

1 Call up AV Menu

3 Change the setting as you like.

2 Select EQ in AV Menu

1/3

Flat

Hard Rock

R&B

Pop

Jazz

AV Menu

Setup

1/2

Sound

Screen Control

Aspect

Exit

[Flat]

Now the setting is changed. Press DISP to exit

from the menu, or BACK to go back to the

previous menu.

1/3

Flat

Hard Rock

R&B

Pop

Jazz

Exit

Basic operations 13

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts index

w e

On the map screen

• Turn on the unit.

On the AV screens

On menu screens

• Turn off the unit if pressed and held.

• Attenuate/restore the sound.

/ATT

In Navigation Menus:

Switch to the AV

screen.

In AV Menu: Change

the source and switch

to the AV screen.

Switch to the AV screen. • Change the source.

AV/SRC

Turn off the AV function if pressed and held.

• Change the map view.

• Display your current

Switch to the map screen.

position after scrolling

the map.

MAP/POS

+/–

Adjust the volume.

In Navigation Menus:

Switch to other

menus.

Call up Destination

Call up AV Menu. ☞ [90]

Menu. ☞ [42]

In AV Menu: Go back

to the top screen of AV

Menu or switch to the

AV screen.

Call up Phone Menu if pressed and held when the Bluetooth adapter is connected. ☞ [83]

Enter the scaling mode. Change the display. ☞ [11]

Exit from the menu.

/DISP

Display the Traffic List.

(Not used)

TRAFFIC

☞ [40]

Download from Www.Somanuals.com. All Manuals Search And Download.

On the map screen

On the AV screens

On menu screens

FM/AM: Select preset stations.

Satellite radio: Select categories.

DVD: Select titles/groups.

Files: Select folders.

5 ∞

Music server: Select albums.

iPod/D. player:

Enter the main menu.

Operate the current

source. ☞ [50]

Select an item.

∞

Pause/resume playback.

Bluetooth Audio: Select a device.

FM/AM: Search for stations.

Satellite radio: Search for channels.

Disc, Music server, iPod/D. player,

Bluetooth Audio: Select tracks/

chapters.

• Open/close the control panel.

• Change the control panel angle if pressed and held.

• Enter the manual

scrolling mode.

☞ [22]

/BACK

7/BAND

Tuner: Select the bands.

• Repeat the last voice

Disc: Stop playing.

guidance if pressed

Go back to the

previous screen.

and held during

guidance. ☞ [33]

Call up Shortcut Menu.

Disc: Start playing.

☞ [25]

Confirm the selection.

ENT/

Detach the control panel.

Remote controller—RM-RK250

Installing the batteries

Caution:

R03(UM-4)/

AAA(24F)

• If the range or effectiveness of the remote

control decreases, replace both batteries.

• Do not expose batteries to heat or flame.

The unit is equipped with the steering wheel

remote control function.

• See the Installation/Connection Manual

Before using the remote controller:

• Aim the remote controller directly at the

remote sensor on the unit.

(separate volume) for connection.

• DO NOT expose the remote sensor to bright

light (direct sunlight or artificial lighting).

Remote sensor

Parts index / Remote controller—RM-RK250 15

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations from the remote controller

On the map screen

On the AV screens

On menu screens

In Navigation Menus:

Switch to the AV screen.

In AV Menu: Change the

source and switch to the

AV screen.

Switch to the AV screen. • Change the source.

AV/OFF

MAP/POS

Turn off the AV function if pressed and held.

• Change the map view.

• Display your current

Switch to the map screen.

position after scrolling

the map.

In Navigation Menus:

Switch to other menus.

In AV Menu: Go back to the

top screen of AV Menu or

switch to the AV screen.

Call up Destination Menu.

Call up AV Menu. ☞ [90]

☞ [42]

Call up Phone Menu if pressed and held when the Bluetooth adapter is connected. ☞ [83]

Display the Traffic List.

(Not used)

TRAFFIC

☞ [40]

Call up Shortcut Menu.

Disc: Start playing/pause.

Confirm the selection.

ENT 6

☞ [25]

FM/AM: Select preset stations.

Satellite radio: Select categories.

DVD: Select titles/groups.

Files: Select folders.

5 ∞

Music server: Select albums.

iPod/D. player:

Enter the main menu.

Scroll the map (in eight

directions).

Select an item.

∞

Pause/resume playback.

Bluetooth Audio: Select a device.

FM/AM: Search for stations.

Satellite radio: Search for channels.

Disc, Music server, iPod/D. player,

Bluetooth Audio: Select tracks/

chapters.

Call up Dial Menu when the Bluetooth adapter is connected. ☞ [86]

PHONE

Repeat the last voice

guidance if pressed and

held during guidance.

BACK/BAND

/7/

VOL +/–

Tuner: Select the bands.

Disc: Stop playing.

Go back to the previous

screen.

Adjust the volume.

Scale the map.

(Not used)

+/–

Start guidance to a home.

☞ [24]

Start guidance to a home.

☞ [24]

HOME

Attenuate/restore the sound.

ATT

DISP

Enter the scaling mode. Change the display. ☞ [11]

Exit from the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Only on the AV screens

• Make selections in disc menus.

• DISC +/– buttons: Change discs for a CD changer.

Disc: Confirm the selection.

;

ENT

TOP M

DVD MENU

OSD

RETURN

DIRECT/

CLEAR

DVD/DivX 6: Show the disc menu. ☞ [67]

VCD with PBC: Resume PBC playback. ☞ [67]

Display the on-screen bar. ☞ [68]

VCD with PBC: Return to the previous menu. ☞ [67]

Disc: To select a chapter/title/group/folder/track directly. ☞ [66]

Disc: Change the aspect ratio of the playback pictures.

ASPECT

Disc: To select a chapter/title/group/folder/track directly. ☞ [66]

Tuner: Select a preset station.

Satellite radio: Input a channel number directly or select a preset channel.

CD changer: Select a disc.

Bluetooth phone: Input telephone number. ☞ [87]

Number

keys

Disc: Reverse search/forward search. Slow playback if pressed while paused.

Disc: Select audio languages/audio channels.

Disc: Select subtitles.

1/¡

Disc: Select a view angle.

ghj

These buttons do

not function at this

position.

;

Remote controller—RM-RK250 17

Download from Www.Somanuals.com. All Manuals Search And Download.

Navigation System

20 Safety instructions for

Navigation System

22 Basic operations

24 Registering your home

To register your home

To go home

26 Starting guidance

Setting a destination using Shortcut Menu

Setting a destination using Destination Menu

To go back to where you started

28 Searching for a place

By address

POI near a place/route

From last destinations

From the list of POI

From your favorites

By telephone number

By coordinates

32 How you are guided

Getting information on your route and places

Customizing how you are guided

Download from Www.Somanuals.com. All Manuals Search And Download.

36 Arranging your route

Setting places to stop by

Saving and loading routes

Avoiding a congestion ahead

38 Registering favorite points

Marking your favorite points

Editing your favorite points

40 Traffic information on map

What is TMC?

Checking the traffic information

How traffic information is reflected in navigation 41

42 Navigation menu items

Destination Menu

Information Menu

Setup Menu

47 Additional information

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety instructions for Navigation System

• Traffic signs should be observed carefully

SAFETY INSTRUCTIONS

while driving using the Navigation System.

Navigation System is only an aid. Driver must

always decide whether or not to heed the

information provided. JVC does not accept

liability for erroneous data provided by the

Navigation System.

Use of the Navigation System is only permitted

if the traffic conditions are suitable and you

are absolutely sure that no risk, obstruction

or inconvenience will be incurred to you,

your passengers or other road users. The

requirements of the Road Traffic Regulations

must always be followed. The destination must

not be entered while driving the car.

The Navigation System serves solely as an aid

to navigation. It never releases the drivers from

their duties to drive carefully and to make

own judgement in road traffic. Inaccurate

or incorrect instructions may happen to be

given due to changing traffic conditions. The

actual road signs and traffic regulations must

therefore always be observed. In particular, the

Navigation System cannot be used as an aid to

orientation when visibility is poor.

• Traffic guidance is restricted to

passenger vehicles only. Special driving

recommendations and regulations for other

vehicles (e.g. commercial vehicles) are not

included.

• Do not operate the unit while driving.

Terms of licence

You are granted a non-exclusive licence to use

the database for your personal purposes. The

present licence does not authorise the granting

of sublicenses.

Use of the data is only permitted in this

specific JVC system. It is forbidden to extract

or make further use of significant parts of

the database content, or to duplicate, modify,

adapt, translate, analyse, decompile or reverse-

engineer any part thereof.

This Navigation System must only be used for

its intended purpose. The volume of the car

radio/Navigation System must be adjusted so

that external noise is still audible.

Navigation guidance is performed, based on

the database, therefore, it may not be applicable

to the current situation because of changes in

traffic conditions (e.g. changes in tollroads,

principal roads, one-way traffic, or other traffic

regulations). In this case, observe the current

traffic signs or regulations.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING:

When replacing/rotating the tires:

It is required to clear all the accumulated

calibration data which is important for accurate

navigation. To clear the data, perform Reset

Calibration on page 46.

Road traffic regulations always take priority

when a vehicle is being driven in traffic.

Navigation System is only an aid. Errors may

occur in individual data items/entries. At all

times, the driver must decide whether or not to

heed the information provided.

JVC does not accept liability for erroneous data

provided by the Navigation System.

On map updating

If “Your map data is more than one year old

and updates may be available.” appears on the

monitor, visit <http://www.jvc-exad.com>.

For details about updating your unit, visit

<http://www.jvc-exad.com>.

Safety instructions for Navigation System 21

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

Current position mode

—The map scrolls automatically so that your position is always at the center of the map.

Scale

Show traffic information. (☞ [40]

)

Scale the map.

Switch to the AV screen.

Adjust the volume.

Your position

Call up a menu screen.

Current time

Current street name

Call up Shortcut Menu.

Change the map view. (

next page)/Display your

current position.

☞

Scroll the map.

Operate the current AV source. (☞ [50]

)

To scroll the map

To change the map scale

Scale bar

Zoom in

Zoom in rapidly

Zoom out

Zoom out rapidly

The map scrolls in eight directions.

• Press and hold the button to keep

scrolling the map.

To display your current position

Direction and

distance from your

current position

Download from Www.Somanuals.com. All Manuals Search And Download.

To change the map view

To call up menus

Navigation Menus

The map view changes as follows:

Each time you press the button, the menu

switches as follows:

Heading Up

3D Map

North Up

(Map screen)

Heading Up

The map rotates so that you are always

displayed heading “upwards.” The direction

is displayed with a compass icon

Destination Menu

Information Menu

Setup Menu

(Back to the map screen)

Menu operations ☞ [13]

Menu items ☞ [42 – 46]

Shortcut Menu

While the map is displayed...

3D Map

The map is displayed in “heading up” and in

a three-dimensional view. The direction is

Shortcut Menu appears. ☞ [25]

displayed with a compass icon

Icons on the map

Favorite points (☞ [38 – 39]

)

POI (Point Of Interest) (☞ [30, 49]

)

North Up

The map view is oriented with north

Traffic (☞ [40, 50]

)

“upwards,” like usual paper maps. The

direction you are heading to is displayed at

the upper right corner of the screen with an

• Favorite icons are displayed on the map when

a group is selected in the Favorite Icon

setting (☞ [45]) and the map scale is between

100 ft (30 m) and 1.2 mile (2.0 km).

icon such as

• POI icons are displayed on the map when a

group is selected in the POI Icon setting (☞

[45]) and the map scale is 100 ft (30 m) or

160 ft (50 m). (The airport icons are displayed

when the map scale is between 100 ft (30 m)

and 2.0 mi (3.0 km).)

• Traffic icons are displayed on the map when

the Traffic Display setting is activated

(☞ [45]) and the map scale is between 100 ft

(30 m) and 1.2 mile (2.0 km).

You can also change the map view through

Setup Menu ] Map Options

]

Map

View (☞ [45]).

Basic operations 23

Download from Www.Somanuals.com. All Manuals Search And Download.

Registering your home

To register your home

To go home (Home)

you go often, as Home, so that you can easily set

that place as destination.

When you have registered your home, you can

easily get guided to home.

• You can register homes only after calibration

is finished. (☞ [9])

While not guided...

1 Call up Shortcut Menu.

1 If you are at home now, check

that your home is displayed at

the center of the map.

• Adjust the position by scrolling the map if

necessary.

2 Call up Shortcut Menu.

2 Select [Go Home]

to start

guidance.

• If you have registered several homes,

select the one you want to go to from a

list.

On the remote:

3 Select [Add to Favorite]

The home is marked with

icon.

You can also be guided to home through

Destination Menu ] Home

To cancel guidance

4 Select [Set Home]

1 Call up Shortcut Menu.

2 Select [Cancel Guidance]

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

The home is marked with

icon.

• The icon may not appear depending on the

map scale and your Favorite Icon setting.

(☞ [45])

• You can register several places as Home by

registering the places as favorite points and

setting their group to Home. (☞ [38, 39])

You can also cancel guidance through

Destination Menu ] Cancel Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

What is Shortcut Menu?

On the map screen, you can call up Shortcut Menu by pressing ENT. Shortcut Menu is a gateway

to various operations.

Shortcut Menu

While not guided

Map screen

While guided

To select an icon, press ENT or one of the four

keys on the right circle button corresponding

to the icon.

Icon

Name

View

Function

Button

Show information on this place. ☞ [35]

Information

Start guidance to a home. ☞ [24] (Not

Go Home

Set Home

selectable if no home is registered.)

when no home is registered and a favorite

icon is selected.)

Cancel

Guidance

Cancel the guidance. ☞ [24]

Add to Favorite Add this place to your favorite points. ☞ [38]

Edit this favorite point. ☞ [39] (Appears

Edit Favorite

only when a favorite icon is selected. Not

selectable while driving.)

Vicinity

Go Here

Search for POI around this place. ☞ [29]

Start guidance to this place. ☞ [26]

Recalculate the route to stop by this place. ☞

[36] (Appears only while guided.)

Add to Via

Point

_{Download from Www.Somanuals.com. All Manuals Searc}R_he_Ag_ni_dst_De_ori_wn_ng_loy_ao_d.ur home 25

Starting guidance

• You can set destinations only after calibration is finished. (☞ [9])

Setting a destination using Shortcut Menu

Scroll the map to display the destination at the center of the

map.

Call up Shortcut Menu.

Select [Go Here]

to start guidance.

The System starts calculating the route to the selected destination, and guidance starts.

To cancel guidance

You can also cancel guidance through

Destination Menu ] Cancel Guide

1 Call up Shortcut Menu.

2 Select [Cancel Guidance]

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting a destination using Destination Menu

Call up Destination Menu.

Select one of the methods to search for your destination.

Destination

Home*

1/2

Destination

POI

2/2

☞ [24]

☞ [30]

☞ [31]

☞ [below]

☞ [28]

Return**

Address

Vicinity

Favorite

Telephone

Coordinates

Route Edit

☞ [29]

☞ [30]

During guidance, Cancel Guideappears.

** During guidance, Avoid Sectionappears.

• You cannot select the items when they are gray.

To see the search result on

map

The information on the search result appears.

0.7 mi

Direction and distance from

your current position

Select [Go Here]

to start guidance.

The System starts calculating the route to the selected destination, and guidance starts.

To go back to where you started (Return

)

You can go back to the start point of the last guidance.

1 Call up Destination Menu.

Destination

Return

]

Starting guidance 27

Download from Www.Somanuals.com. All Manuals Search And Download.

Searching for a place

To input names, addresses, or numbers

3 Select the item you want from the

list.

Ex. Input screen for a city name

By address (Address)

Enter a space Display other

1 Call up Destination Menu.

keyboards*

Delete the last character

Display the list of

matches

You can also change the keyboard by pressing

DISP. For available characters, ☞ [105].

Destination

Address

]

Address

New York

** Buttons vary depending on the input item.

City

Street

1 Enter characters.

Move the cursor on the

keyboard

3 Input the state name.

• Input the city name if a state is already

selected.

Enter the selected character

- Input State Name -

• Available characters are automatically

narrowed down as the System searches its

database for matches.

2 Display the list of matches.

All

Displays the list of all the states.

• This button is available when the matches

are narrowed down to 100 or less.

• You can also display the list of matches by

pressing and holding ENT.

4 Input the city name.

- Input City Name -

• When the matches are narrowed down to

5 or less, the list appears automatically.

More Street

Select this to search by street

name.

• Inputting characters ☞ [left column]

Download from Www.Somanuals.com. All Manuals Search And Download.

While guided, select the area to search if

necessary.

5 Input the street name.

• You can also select the center of the city.

(The list of city centers may appear.) You

do not have to input the house number in

this case.

[Hold]

• Select the area to search from the list if

Select Area

Select Area is displayed.

Local Area

Near Destination

Along Route

6 Input the house number.

• You can also select the entire street or an

intersection on the street.

• If no data of house number for the

selected street is available in the database,

this step is skipped.

Local Area: within 1.2 mi (2 km) of

your current position. If no POI is

found in this area, the System expands

the area to search.

Near Destination: within 1.2 mi (2 km)

of the destination. If no POI is found in

this area, the System expands the area

to search.

Along Route: 30 mi (50 km) along the

route you are taking.

POI near a place/route (Vicinity

)

You can search for a POI around the place

where you are now. While guided, you can also

search for a POI near the destination or along

the route.

3 Select a category (then a sub

1 Call up Destination Menu.

category if any) of the POI.

Select Category

All Categories

Gas station

Hotel

1/3

Destination

Vicinity

]

Parking

Select Category

All Categories

Gas station

Hotel

1/3

Restaurant

Area: Local

Change

The result is listed in the order of distance

from the place where you are.

Parking

Restaurant

Area: Local

Change

4 Select a POI from the list.

You can search for a POI around a place

on the map through Shortcut Menu ]

[Vicinity]

above after selecting [Vicinity]

. Follow steps 3 and 4

_{Download from Www.Somanuals.com. All Manuals Search}S_Ae_na_dr_Dc_oh_win_ng_loafo_d.r a place 29

From last destinations (Previous

)

From the list of POI (POI)

You can select a place from the last 50

destinations and via points.

The System has a huge database of POI (Point

Of Interest), such as restaurants, gas stations,

hospitals, etc.

1 Call up Destination Menu.

Destination

POI

]Previous

The list of previous destinations/via points

is displayed.

]

POI

New York

City

Category

Name

[Hold]

A confirmation message appears. Press

ENT to confirm the operation. Press BACK

to cancel.

Download from Www.Somanuals.com. All Manuals Search And Download.

By category and name

By telephone number (Telephone

)

1 Select a category (then a sub

1 Call up Destination Menu.

category if any) of the POI.

2 Input the name of the POI you are

looking for.

Destination

Telephone

]

• Inputting characters ☞ [28]

3 Select a POI from the list.

3 Select a state.

• Input the telephone number if a state is

already selected.

Directly by name

1 Input the name of the POI you are

4 Input the telephone number.

looking for.

- Input Phone Number -

• Inputting characters ☞ [28]

2 Select a POI from the list.

Delete the last

character

Display the list of matches

• Inputting characters ☞ [28]

From your favorites (Favorite

)

5 Select a POI from the list.

• Registering your favorite points ☞ [38].

1 Call up Destination Menu.

By coordinates (Coordinate

)

Destination

Favorite

]

1 Call up Destination Menu.

Select Group

Home

1/2

Friend

Destination

Coordinates

Relative

Business

Visit

]

3 Input the latitude and the

Delete

longitude.

3 Select a group.

4 Select a favorite point from the

Moves the cursor.

To correct a

list.

misentry, move

the cursor and

enter the number

South

Detail

again.

Switches South and North

for latitude.

4 Select Detail when finished.

_{Download from Www.Somanuals.com. All Manuals Search}S_Ae_na_dr_Dc_oh_win_ng_loafo_d.r a place 31

How you are guided

Destination found

Route calculation

Calculating...

To cancel calculation, press BACK.

0.7 mi

Screen while guided

Estimated time of

arrival and distance

to the destination/

next via point

Route to take

Current time

Next turn/

Distance to the

next turn

Name of the next street

To cancel guidance

You can also cancel guidance through

Destination Menu ] Cancel Guide

1 Call up Shortcut Menu.

To adjust the volume of the voice guidance

☞ [43] Volume

2 Select [Cancel Guidance]

Download from Www.Somanuals.com. All Manuals Search And Download.

Guidance at turns

When you approach a turn, the System guides you with voice guidance and indications on the

screen.

• Guidance voice comes out only through the front speakers (and the front line out on the rear).

Guidance point

“In

0.2 mile, make

a right turn.”

When you do not

have to make a

turn, the System

gives no guidance.

Following turn (if any)

“In

0.1 mile, make

a right turn.”

Indicate the distance to the next turn

“Make a right

turn.”

What if I miss a turn?

Don’t worry. The System calculates a

new route quickly and guides you to

the destination.

To repeat the last voice guidance

• You can remove the progress bar to the next

turn by pressing MAP.

[Hold]

How you are guided 33

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting information on your route and places

• You can also view the trip through

To see the itinerary and the turns list

Information Menu ] Trip

Map screen

• You can also view the turns list through

Information Menu ] Turns List

[Hold]

Trip information

Trip

Distance Driven

8.1mi

0:12

Time Driven

Average speed

40mph

Trip

Info

Turn on map

Turns list

Turns List

500 ft A124

2 mi A2120

1/5

2.5mi xx street

6 mi Z square

7 mi B12

Prev.

Press

∞

to see the next/previous turn.

To get information on the destination and via points

1 Call up Information Menu.

[twice]

Information

Destination

]

3 Select the destination or a via point.

Remaining 0.7mi

Arrival 1:54PM

1:54 PM 0.7 mi

Download from Www.Somanuals.com. All Manuals Search And Download.

To check the estimated arrival time and

distance to the next via point

To see how your trip will go

Information Menu ] Simulation

appears on the display.

[Hold]

To cancel simulation and resume guidance,

press MENU, then DISP.

disappears.

Each time you press and hold the button,

the information on the upper left corner

alternates between that of the next via point

and of the final destination.

Customizing how you are guided

To customize the guidance and display on the

map screen

☞ [43] Guidance View

To see information on a place

• This operation is always possible regardless of

whether you are guided or not.

To customize how the map scale changes

1 Display where you want to

know of at the center of the

map.

☞ [45] Auto Zoom

To customize the voice guidance on an AV

screen

☞ [44] Interruption

2 Call up Shortcut Menu.

To customize the mixing of audio sound and

voice guidance

☞ [43] Audio Mixing

The guidance continues even when you

switch the display to an AV screen. Guidance

information is displayed on the lower-right

corner of the AV screen.

3 Select [View Information]

FM1

0.7 mi

Station name

92.5 MHz

If a telephone number is available, you can

call to the number through JVC’s Bluetooth

adapter. ☞ [86]

Distance to the next turn/Turn icon

(While not guided: Speed/Direction)

You can also get information on your current

position through Information Menu ]

Current Position

How you are guided 35

Download from Www.Somanuals.com. All Manuals Search And Download.

Arranging your route

Setting places to stop by

3 Select the via point you want to

move.

After selecting your destination, you can select

up to nine places (“via points”) to stop by.

Select Point

1/2

Station

Forest Inn

Intr’l Airport

Car Dealer

To add via points

After guidance has started...

Michael

1 Select a place you want to stop

by.

Select

4 Move the selected via point in

• Searching for a place ☞ [27]

the list.

Move Point

1/2

Station

Forest Inn

Car Dealer

Michael

Intr’l Airport

0.7 mi

Set

Delete

5 Repeat steps 3 and 4 to move

2 Select [Add to Via Point]

other via points.

6 Finish the rearrangement.

The System starts calculating the new route,

and guidance starts.

• You can also use MENU, DISP,

MAP, or

You can also set via points on the map

through Shortcut Menu ] [Add to Via

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

Point]

The System starts calculating the new route,

and guidance starts.

• No confirmation message appears if the

via points are not changed.

To delete a via point

Press and hold ENT in step 4.

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

To rearrange the sequence of via points

1 Call up Destination Menu.

Destination

Route Edit

Edit

]

For other options for routing ☞ [44] Route

Options

]

The list of via points appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

To delete saved routes

Saving and loading routes

1 Call up Destination Menu.

You can save up to 50 combinations of

destination and via points. You can easily call

up your usual route without the trouble of

setting destinations.

Destination

Route Edit

Delete

• Each route can contain up to nine via points.

]

To save a route

]

1 Select your destination (and via

points if necessary), and start

guidance.

3 Check the boxes at the head of

the routes you want to delete.

• Checkbox operations ☞ [105]

2 Call up Destination Menu.

Destination

Route Edit

Save

]

4 Delete the selected routes.

]

4 Name the route you are saving.

[Hold]

• Inputting characters ☞ [105]

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

5 Select Store

To load a saved route

Avoiding a congestion ahead

1 Call up Destination Menu.

If you realize a congestion exists ahead...

Destination

Route Edit

Load

While being guided...

]

1 Call up Destination Menu.

]

3 Select the route you want to

Destination

Avoid Section

take.

]

Load

Route A

Route B

Route C

Route D

3 Select the distance to avoid.

Select Distance

1mi

3mi

5mi

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

10mi

15mi

Start

The route is calculated, and guidance starts.

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

A detour is calculated, and guidance starts.

_{Download from Www.Somanuals.com. All Manuals Search}A_Ar_nr_da_Dn_og_win_ng_loay_do_.ur route 37

Registering favorite points

Just like you mark your friend’s house or a nice

Chinese restaurant on your map book, you can

To proceed to edit the registered favorite

point, select [Edit Favorite]

step 4.

after

Marking your favorite points

You can open the edit screen in step 3 of

• You can register 300 favorite points.

• You can register favorite points only when

the map scale is 1.2 mile (2.0 km) or more

detailed.

“Editing your favorite points.”

Editing your favorite points

1 Display the place you want to

save as favorite at the center of

the map.

1 Call up Destination Menu.

• Searching for a place ☞ [27]

2 Call up Shortcut Menu.

Destination

Favorite

]

Select Group

Home

1/2

Friend

Relative

Business

Visit

Delete

3 Select [Add to Favorite]

3 Select a group, then a favorite

point to edit.

The favorite point is registered in the group

of Other and marked with icon.

• The icon may not appear depending on

the map scale and your Favorite Icon

setting. (☞ [45])

[Hold]

Edit Favorite

Input Name

Other

• To be guided to a favorite point ☞ [31]

Input Address

Input Phone Number

Sound Off

Delete

Download from Www.Somanuals.com. All Manuals Search And Download.

To delete a favorite point

Press and hold ENT after step 3 of “Editing

your favorite points.”

4 Select the item you want to edit.

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

• You cannot delete a favorite point directly

after editing it. To delete it, exit from the

Edit Favorite screen once and do the

procedure above.

The name of the favorite point.

• You can use up to 32

characters.

See the table on the right for the

available ten groups.

Name

Group

To delete all the favorite points in a group

Categorize the favorite points so

that you can find them easily.

The address of the favorite

point.

If you have connected

KS-BTA200, you can call to this

number. ☞ [86]

Sound Off, Alarm, Bell,

Siren

You can assign a sound to

each favorite point. You hear

the assigned sound when you

come close (about within 660 ft

(200 m)) to the favorite point.

• Press ENT to listen to a sample

sound.

1 Press and hold ENT after step 2 of

“Editing your favorite points.”

Address

2 Select the groups to delete.

Telephone

number

Select Group

Home

1/2

Friend

Relative

Business

Visit

Sound

Check

Delete

• Checkbox operations ☞ [105]

3 Delete the selected groups.

[Hold]

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

5 Edit the item.

• Inputting characters ☞ [105]

Icons and groups for favorite points

Home

Shopping

Friend

Relative

Business

Visit

Food

Caution

Sightseeing

Other

_{Download from Www.Somanuals.com. All Manuals S}R_eae_rg_ci_hst_Ae_nr_din_Dg_of_wa_nv_loo_ar_dit_.e points 39

Traffic information on map

What is TMC?

Checking the traffic information

Traffic Message Channel (TMC) is a technology

for delivering real-time traffic information to

drivers. The traffic information sent by an FM

radio station are received and analyzed by the

System. The System can inform you of where

congestion exists, and how you can detour it.

• You do not have to tune in to a special radio

station to receive the traffic information.

Traffic

1/2

Eastbound

Northbound

Southbound

While guided, select the area to see the

information of.

Along Route or All Information

How to get traffic information

Traffic information is supplied from NAVTEQ

Traffic RDS.

As the traffic information is transmitted

by FM radio stations, JVC cannot assume

responsibility for the completeness or

accuracy of the information.

To see detailed information

Select an item on the list and press ¢.

Traffic

Traffic information on the map

Congestion

Traffic icon

You can also call up the Traffic List through

Information Menu ] Traffic

You can also see detailed information of a

traffic icon on the map in the following way:

Display a traffic icon at the center of the map

] Shortcut Menu ] [View Information]

• List of traffic icons ☞ [50]

• Traffic icons and congestion lines are

displayed on the map when the Traffic

Display setting is activated (☞ [45]).

• Traffic icons are displayed on the map

when its scale is between 100 ft (30 m)

and 1.2 mile (2.0 km).

• Congestion lines are displayed on the map

when its scale is between 100 ft (30 m)

and 3.0 mile (5.0 km).

Download from Www.Somanuals.com. All Manuals Search And Download.

How traffic information is reflected in

navigation

If Bypass Traffic is set to Manual Reroute

(☞ [44]), [Reroute] appears on the screen when

the traffic service informs the System of traffic

accidents or congestion ahead on your route.

Reroute

To check the information and decide whether

to calculate a detour

[Hold]

If Bypass Traffic is set to Auto Reroute

the System automatically calculates a new route

when the traffic service informs of an obstacle

on your route.

If Bypass Traffic is set to Off, the System

does not take traffic information into account in

calculating a route.

Traffic information on map 41

Download from Www.Somanuals.com. All Manuals Search And Download.

☞ [12] for the detailed Menu operations.

Navigation menu items

Destination Menu

Menu items

Start guidance to a home. (Appears only while not guided.) ☞ [24]

Cancels the guidance. (Appears only while guided.) ☞ [24, 26, 32]

Home

Cancel Guide

Starts guidance to the place where you have started your last guidance.

(Appears only while not guided.) ☞ [27]

Return

Calculate a new route avoiding the selected distance ahead. (Appears only

while guided.) ☞ [37]

Avoid Section

1mi

3mi

5mi

10mi

15mi (or 1km

3km

5km

10km

15km ^*1

)

Address

Vicinity

POI

Search for a place using the database in the System. ☞ [27]

Favorite

Telephone

Coordinates

• Arrange the order of via points.

Route Edit

• Save, load or delete routes. ☞ [36]

Edit Save, Load, Delete

*1 Depends on your setting of Measuring Units(☞ [46]).

Information Menu

Menu items

You can see the information on your current position.

State, City, Street, Latitude, Longitude

Current Position

You can check the traffic information. ☞ [40]

Traffic

Along Route^*1, All Information

Turns List^*1

Trip^*1

Destination^*1

You can see the list of turns on your route. ☞ [34]

You can see the information on your route. ☞ [34]

You can see the list of via points and the destination. ☞ [34]

You can see the status of GPS reception.

GPS

*1 Selectable only while guided.

Download from Www.Somanuals.com. All Manuals Search And Download.

Information Menu (continued)

Menu items

You can check the connection status.

Learning Lv., Angle, GPS Antenna, Gyro, Speed Signal,

Parking Brake, Reverse Signal, Illumination, Tel. Muting

Connection

You can check the model name, the version of the unit, and the version of

the map database.

Version

Once the route is determined, you can simulate it on the map. ☞ [35]

Simulation

Setup Menu

Menu items

Selectable settings

(Initial setting)

Gender

Volume

Female, Male^*1

Adjust the volume of the voice guidance.

Off

01 to 50 (25)

Select the guidance output channel.

Output Channel

Audio Mixing

L-ch Only, R-ch Only, L-ch & R-ch

You can turn down the volume of the AV source while voice

guidance is produced.

Muting: The AV source sound does not come out.

Attenuation: The AV source sound is lowered.

Normal: The AV source sound is not changed.

Select the items to be displayed at turns.

Guidance View

• Next turn icon: Big

Auto Magnification

• Following turn icon: On

• Progress bar to the turn: On

• Next turn icon: Big

Symbolic View

• Following turn icon: Off

• Progress bar to the turn: Off

• Next turn icon: Small

Simple View

• Following turn icon: Off

• Progress bar to the turn: Off

*1 Press ENT to listen to a sample voice with the current setting.

_{Download from Www.Somanuals.com. All Manuals Sear}N_cha_Av_nig_da_Dt_oio_wn_nlm_oae_dn_.u items 43

Setup Menu (continued)

Menu items

Selectable settings

(Initial setting)

Select the voice guidance output on an AV screen.

• A small icon of the next turn is always displayed at the lower-

right corner of the AV screen while guided, regardless of this

setting. If you want to see the turn on map, press MAP to switch

to the map screen.

Interruption

Off

Bypass Traffic

Voice Cruise

Off

Auto Reroute Manual Reroute ☞ [41]

When this function is activated, the System automatically increases

the guidance volume level as the car speeds up.

To obtain stronger effect, set the level to higher numbers.

Off

01 to 10 (05)

Select the type of attention tone, which comes out before voice

guidance.

Off, Attention 1, Attention 2, Attention 3

• Press ENT to listen to a sample sound.

Attention Tone

Priority

Fastest: The System calculates the shortest journey time.

Shortest: The System calculates the shortest route to the

destination.

• This setting is effective next time the System calculates a route.

Check the boxes at the head of the options you want to be effective.

• This setting is effective next time the System calculates a route.

Avoid Highway

Avoid Ferry

Avoid Toll Road

Day Color

Select the color for the day screen.

Type 1, Type 2, Type 3

Select the color for the route.

Route Color

Night Mode

Color 1, Color 2, Color 3

Select the condition to switch the display to the night screen.

Off: Cancels.

Auto: Switches to the night screen when you turn on the

headlights.

Time: Switches to the day/night screen at set times.

• When you choose Time, set when to switch the display color on

the following screen.

Brightness^*2

Set the brightness of the screen.

–15 to +15 (00)

*2 This setting is shared with the Screen Controlsetting in AV Menu. (☞ [96]

)

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Menu (continued)

Menu items

Map View

Auto Zoom

Selectable settings

North Up Heading Up

(Initial setting)

3D Map ☞ [23]

Select how the zoom scale changes.

Off: (Effective only while guided) Zoom into 100 ft (30 m) scale

at turns if Guidance View is set to Auto Magnification. If

else, the scale does not change at turns.

Fit For Guidance: (Effective only while guided) When you

approach turns, the scale changes gradually so that your current

position and the turn is always displayed on the map at the same

time.

Fit For Speed: The scale changes gradually in accordance with

the speed of your car; as you slow down, the map is zoomed in.

Check the box at the head of each POI category to display its icons

on the map.

POI Icon

Check the box at the head of each favorite group to display its icons

on the map.

Favorite Icon

Car Tracks^*3

Display: Check the box to display the tracks of your car on the

map.

Record^*4: Check the box to record the track of your car.

Delete: Deletes the recorded tracks.

Check the box to display the current/next street name on the

monitor.

Street Name

Check the box to display the one-way icon on the map.

Check the box to display the traffic icons on the map.

One-Way

Traffic Display

*3 When you want the track of the current drive displayed, you need to check both Displayand Record.

*4 The recorded tracks are deleted from old ones when the internal memory gets full.

_{Download from Www.Somanuals.com. All Manuals Sear}N_cha_Av_nig_da_Dt_oio_wn_nlm_oae_dn_.u items 45

Setup Menu (continued)

Menu items

Selectable settings

(Initial setting)

Select the angle of the unit measured by the supplied gauge. (See

also the Installation/Connection Manual.)

Installation

Angle

: –5.0° to 1.0°

: 1.0° to 6.0°

: 6.0° to 14.0°

: 14.0° to 32.0°

• It is not recommended to install the main unit at an angle of

more than 30˚; otherwise, the malfunction may result.

• Guidance is canceled when you change this setting.

Select whether to use WAAS and EGNOS to increase the accuracy

WAAS/EGNOS

of positioning.

Off: Cancels.

On: Activates.

Language^*5

Select the language used for on-screen information and voice

guidance.

English US, Español, Français

Reset the calibration data in the following cases:

• When you reinstall the unit to another car.

Reset Calibration

• When you change Installation Angle.(☞ above)

• When you replace or rotate the tires.

Once this is carried out, the calibration data is cleared. Calibration

starts when you exit from the menu. (☞ [9])

• Guidance is canceled when you reset the calibration data.

Select the measuring units for distance.

Measuring Units

Coordinates

km / m mi / ft

Select the measuring units for coordinate degrees.

Deg / Min / Sec Deg / Milli / Micro

If you find your current position displayed on a wrong place on the

map, use this setting to correct your position.

Adjust the position with 4¢5∞, then the direction with 5∞.

Car Position

*5 This setting is shared with the Languagesetting in AV Menu (☞ [90]).

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional information

• POI search in Along Route is canceled if the

guidance finishes or if rerouting starts before

the search completes.

Initial settings

• If you select On for Store Display Mode

the system starts up in demonstration mode

for shops, and the initial setup screen appears

every time you turn on the unit after turning

off and on the ignition switch. Select Off to

obtain the full performance from the unit.

By coordinates

• If the entered position is out of the database,

Out of the map coverage. appears on the

display. Enter again.

Basic navigation procedure

Basic operations

• When you reach the area approximately

within 100 ft (30 m) around the destination/

via point, the Navigation System considers

that you have reached your destination/via

point.

• In a small scale, the map scrolling may stop

when the map view approaches the border

of the map coverage. Scrolling resumes in a

larger scale when you keep scrolling the map.

Searching for a place

How you are guided

• While driving at a speed greater than

6 mi/h (10 km/h), following operations are

prohibited:

• If GPS signal reception is poor, navigation

guidance may not be correct.

• The System may not receive GPS signals in

the following places...

– To enter a destination.

If you try to do these operations, the following

screen appears, and you cannot continue the

operation.

– in a tunnel or parking lot in the building

– under an overhead road

– in a place surrounded by high buildings or

by closely standing trees.

You cannot operate while

driving. Operate again

after stopping.

• The position of your car may not be detected

correctly in the following cases...

– when running on a road close to the other

one (e.g. a highway and ordinary road

running in parallel)

• The search result is displayed in North Up

view regardless of your map view setting.

• The name you entered to search for a POI

may be different from the name of the search

result.

– when turning at an almost straight fork in

the road

– when running on a gridiron road

– after taking a ferry, etc.

– when running on a steep mountain road

– when running on a spiral road

– when turning left or right after running

on a long straight road

– when running in a zigzag line on a broad

road

– when starting your car shortly after

starting the engine

From the list of POI

• If no POI data exists for the selected city, POI

not found. appears on the display. Press

BACK until the city entry menu appears, then

re-enter another city.

POI around a place/route

• If no POI data exists for the selected area, POI

not found. appears on the display. Press

BACK until the main categories list appears.

– when running for the first time after

installing the unit

– when changing tires or attaching chains

on the tires

Additional information 47

Download from Www.Somanuals.com. All Manuals Search And Download.

– when tire slip occurs continuously and

frequently

– after running on areas other than a road

(e.g. private lands or parking lots)

– after running in underground or tower

type parking lots

– after rotating your car on a turntable

– after frequent stops and starts in a

congestion

– when the accuracy of GPS is deteriorated

intentionally

– when running on a road constructed

recently

Arranging your route

• Highways are always used to calculate the

route if the distance to the destination is over

120 mi (200 km).

• If the destination cannot be reached without

using highways, ferries, or toll roads, they are

used to calculate the route without respect to

the Route Options settings.

• A detour may not be calculated with Avoid

Section depending on the route.

Traffic information on map

• When Bypass Traffic is set to Manual

Reroute, the rerouting may be canceled

while you are checking due to a change

of traffic condition. The rerouting is also

canceled if you do not confirm the rerouting

in one minute.

• The route calculated by the System is one of

the possible routes to your destination. The

route is not always the most appropriate one.

• If a street name is not available in the

database, Unnamed appears in place of the

street name.

• If no-exit roads (only entering the rotary from

the roads is allowed) exist on the rotary, the

no-exit roads can neither be shown in the

route guidance on the display nor counted in

the route guidance voice message.

• The following phenomena may occur even if

the System is working correctly...

– It may guide to a closed road or to a route

requiring U-turn.

• Traffic information service is only available in

the 48 contiguous United States.

– It may not guide to your destination if

there is only a narrow road or no road to

your destination.

– It may not avoid a congestion even

if Bypass Traffic is set to Auto

Reroute

– It may show a different road name.

– It may not ask you to turn at a junction

even if you need to.

– It may give a guidance different from the

actual road condition.

– It may give an incorrect distance

information.

Download from Www.Somanuals.com. All Manuals Search And Download.

List of POI icons

Gas Station

Emergency

Hospital

Hotel

Lab/Facility

Physician

Parking

Restaurant

Shopping

Others [Medical]

Financial

Travel

ATM

Agency/Info

Bank

Air Transportation

Airport

Service

City Finder

Automotive

Rental

Ground Transportation

Others [Travel]

Sales

Service

Recreation

Bowling

Others [Automotive]

Golf

Community

Agriculture/Farming

Child Service

Outdoor

Skiing

Education

Theme Park/Exercise

Zoo

Government/Administration

Health/Safety

Insurance

Others [Recreation]

Entertainment

Legal Service

Manufacturing

Multimedia

Casino

Museum

Night Club/Bar

Theater

Police/Fire

Post Office

Others [Entertainment]

Real Estate

Medical

Religious

Animal Health

Others [Community]

Drug Store/Pharmacy

Additional information 49

Download from Www.Somanuals.com. All Manuals Search And Download.

List of traffic icons

Traffic Jam

Road works

Road is blocked or closed

Traffic lane closed

Accident

Condition

Other Caution Event

Information

Rain

Snow

Strong winds

Fog

AV source operations in the map screen

Source

Auto search.

Change preset stations.

Change categories.

Change titles/groups/folders.

Change albums.

Tuner

Satellite radio

Disc

Change channels.

Music server

CD changer

iPod/D. player

Bluetooth Audio

Change tracks.

Change folders.

(No function)

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio

52 Listening to the radio

FM station automatic presetting

—SSM (Strong-station Sequential Memory)

Manual presetting

Selecting preset stations

Assigning titles to stations

When an FM stereo broadcast is hard to receive

Tuning in to stations with sufficient signal strength 54

55 Listening to the satellite radio

Activating your subscription after connection

Selecting channels by channel number

Presetting channels

Selecting channels on the lists

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the radio

* Assigned station name.

Band

Equalizer type ☞ [98]

FM1 Preset4

Station name

MHz

92.5

ST DX

Select “TUNER.”

Select the bands.

Search for a station—Auto Search.

• Manual Search: Press and hold either 4 or ¢ until Manual Search appears on

the monitor, then press it repeatedly.

•

lights up when receiving an FM stereo broadcast with sufficient signal strength.

FM station automatic presetting

—SSM (Strong-station Sequential Memory)

This function works only for FM bands.

AV Menu

Mode

SSM

You can preset six stations for each band.

]

SSM appears on the display.

Local FM stations with the strongest signals

are searched and stored automatically in the

FM band.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual presetting

Selecting preset stations

You can preset six stations for each band.

2 Select a preset number.

2 Tune in to the station you want

to preset.

FM1 Preset4

Station name

92.5 MHz

3 Display the Preset List.

On the remote:

FM1 Preset

1 87.5 MHz

2 88.3 MHz

3 88.7 MHz

4 91.5 MHz

5 93.1 MHz

6 95.3 MHz

Store

10:35 AM

80 km/h

2 Select a preset number.

[Hold]

• For FM only: Each time you press and

hold the button, you can change the

bands.

4 Select a preset number.

From the Preset List

FM1 Preset4

Station name

1 Display the Preset List.

FM1 Preset

1 87.5 MHz

Store

92.5

MHz

[Hold]

2 88.3 MHz

3 88.7 MHz

4 91.5 MHz

5 93.1 MHz

6 95.3 MHz

10:35 AM

80 km/h

[Hold]

You can also access the Preset List through

• For FM only: Each time you press and

hold the button, you can change the

bands.

AV Menu

]

List.

2 Select a preset number.

_{Download from Www.Somanuals.com. All Manuals Search}L_Ai_nst_de_Dn_oin_wg_nloto_adt_.he radio 53

Assigning titles to stations

When an FM stereo broadcast is hard

to receive

You can assign a title to up to 30 radio stations.

1 Tune in to the station you want

to assign a title to.

AV Menu

Mode

Mono

]

AV Menu

Title Entry

]

- Input Station Name -

lights up. Reception improves, but stereo

effect will be lost.

To restore stereo effect, select Off in step 2.

Del More Store

4 Assign the title.

• Inputting characters ☞ [105]

• You can use up to 16 characters.

Tuning in to stations with sufficient

signal strength

5 Select Store

If [Name Full] appears

This function works only for FM bands.

Once you have activated this function (selected

Local), it always works when searching for FM

stations.

If you have assigned titles to 30 stations, you

need to delete some titles to name new stations.

After step 3 above...

Title Delete

Select All

1/7

Station name 1

AV Menu

Mode

DX/Local

Local

Station name 2

Station name 3

Station name 4

]

Delete

Check

]

2 Select the titles to delete.

lights up. Only stations with sufficient

signal strength will be detected.

To tune in to all receivable stations again,

select DX in step 2.

• Checkbox operations ☞ [105]

3 Delete the selected titles.

[Hold]

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the satellite radio

Before operating, connect either one of the following (separately purchased) to the CD changer jack

on the rear of this unit.

• JVC SIRIUS radio DLP—Down Link Processor, for listening to the SIRIUS Satellite radio.

• XMDirect Universal Tuner Box—With a JVC Smart Digital Adapter (XMDJVC100: not

supplied), for listening to the XM Satellite radio.

Activating your subscription after connection

For SIRIUS Radio

For XM Radio

1 Turn on the power.

2 Select “SAT” for the source.

JVC DLP starts updating all the SIRIUS

channels. (☞ “GCI update” below.)

• Once completed, JVC DLP tunes in

to CH184 (channel for subscription

guidance).

XMDirect Universal Tuner Box starts

updating all the XM channels. “Channel 1”

is tuned in automatically. (☞ “GCI update”

below.)

3 Check your XM Satellite radio

ID.

3 Check your SIRIUS ID.

☞ [93]

It is labelled on the casing of the

XMDirect Universal Tuner Box. You can

4 Activate your subscription.

also check it by tuning in to “Channel 0” (☞

next page).

Contact SIRIUS on the Internet at <http://

activate.siriusradio.com/>, or call SIRIUS

toll-free at 1-888-539-SIRIUS (7474).

• “Subscription Updated Press Any Key to

Continue” appears on the monitor once

subscription has been completed.

4 Activate your subscription.

Contact XM Satellite radio on the Internet

at <http://xmradio.com/activation/> to

activate your subscription, or you can call

1-800-XM-RADIO (1-800-967-2346).

• Once completed, the unit tunes in to one

of the available channels (Channel 4 or

higher).

GCI (Global Control Information) update:

• If channels are updated after subscription, updating starts automatically, and no sound can be

heard.

For SIRIUS: “Channels Updating XX% completed” appears.

For XM: “UPDATING” appears.

• Update takes a few minutes to complete.

• Do not press any button or perform any operation until updating is completed.

Listening to the radio / Listening to the satellite radio 55

Download from Www.Somanuals.com. All Manuals Search And Download.

Switches the display to program information—artist name/song name(/

composer name: only for SIRIUS Satellite radio).

SIRIUS/XM Band

Channel number Equalizer type ☞ [98]

SR1 Preset4

001ch

Category name

Channel name

Signal indicator

For XM Radio

For SIRIUS Radio

Select “SAT.”

Select a category.

Select “SAT.”

Select a category.

• To select a channel from all

categories (including non-

• To select a channel from all

categories, select “ALL.”

categorised channels), skip this step.

• If you do not select a channel within

15 seconds, the category selected is

canceled. You can select a channel

from all categories now.

Select a channel to listen

to.

• Holding either 4 or ¢ changes

the channels rapidly.

• While searching, invalid and

unsubscribed channels are skipped.

Select a channel to listen

to.

• Holding either 4 or ¢ changes

the channels rapidly.

• While searching, invalid and

unsubscribed channels are skipped.

Checking the XM Satellite radio ID

Select channel “0.”

The 8-digit (alphanumeric) ID number is

displayed on the monitor.

To cancel the ID number display, select any

channel other than channel “0.”

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting channels by channel

number

Presetting channels

You can preset six channels for each band.

On the remote only:

1 Tune in to a channel you want

to preset.

2 Display the Preset List.

SR1

- - - ch

3 _TDirect Channel

SR1 Preset

Store

1 Channel name

2 The City

3 40 at 40

4 Hank’s Place

5 Audio Visions

6 Preview

[Hold]

2 Input the channel number in

• Each time you keep pressing the button,

you can change the bands.

three digits.

3 Select a preset number.

[Hold]

• You can also access the Preset List through

AV Menu

]

List

]

Preset List.

• “SIRIUS” and the SIRIUS dog logo are

registered trademarks of SIRIUS Satellite

Radio Inc.

• XM and its corresponding logos are registered

trademarks of XM Satellite Radio Inc.

• “SAT Radio”, the SAT Radio logo and all

related marks are trademarks of SIRIUS

Satellite Radio Inc., and XM Satellite Radio,

Inc.

_{Download from Www.Somanuals.com. All Manua}L_lsis_Ste_ean_ri_cn_hg_At_no_dt_Dh_oe_ws_na_lot_ae_dll_.ite radio 57

Selecting preset channels

Selecting channels on the lists

1 Display the Preset List.

You can select a channel using one of the

following lists—Preset list/Category list/

Channel list.

SR1 Preset

Store

1 Channel name

2 The City

3 40 at 40

4 Hank’s Place

5 Audio Visions

6 Preview

[Hold]

AV Menu

List

Preset List/

Category List/

]

• Each time you keep pressing the button,

you can change the bands.

]

2 Select a preset number.

Channel List

•

Preset List: ☞ left column

Category List: Displays the categories.

= Select a category, then a channel within

the selected category.

•

Channel List: Displays all channels

(XM) or all channels within the current

category (SIRIUS). = Select a channel.

On the remote:

1 Select the bands.

3 Select (a category, then) a

channel.

2 Enter the preset number.

• You can also access the Category List by...

[Hold]

Download from Www.Somanuals.com. All Manuals Search And Download.

Discs and HDD

60 Disc operations

Playable discs/files

Selecting playback modes

Selecting tracks on the list

Prohibiting disc ejection

Remote operations

Special functions for DVD Audio

Operations using the on-screen bar

70 Music server operations

Selecting tracks using lists

Selecting playback modes

Recording/copying tracks from a disc

Editing the library

Checking the remaining storage size

77 CD changer operations

Selecting playback modes

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc operations

The disc type is automatically detected, and

playback starts automatically (for some

discs: automatic start depends on its internal

program).

To insert a disc

If a disc does not have any disc menu, all tracks

in it will be played repeatedly until you change

the source or eject the disc.

To eject the disc

Disc type

Equalizer type ☞ [98]

01 0:00:03

Album Name

Artist Name

Track Name

Stop playback. Start playback.

Playback mode ☞ [64]

Select “DISC.”

Each time you press DISP, the display

changes.

When a disc contains different types of file

(music, movie or still pictures), you need to

select the file type to play back. (☞ [91] File

For picture discs: playback picture

information vehicle information (☞ [11]

Video input* (☞ [82] (back to the

beginning)

For audio discs: disc information vehicle

information Video input* (back to the

beginning)

disc

Type

)

If “ ” appears on the monitor, the unit

cannot accept the operation you have tried to

do.

• In some cases, without showing “ ,”

operations will not be accepted.

Appears only when you have selected Videoor

Camerafor Video Inputsetting (☞ [93]).

• For discs except DVD and VCD: The control screen

appears on the connected external monitor. (☞

[102]

)

Download from Www.Somanuals.com. All Manuals Search And Download.

Playable discs/files

Disc type

Recording format, file type, etc.

Playable

DVD Video

DVD Audio

DVD

DVD-ROM

DVD Video

DivX/MPEG1/MPEG2

JPEG

MP3/WMA/WAV

ASF

DVD-VR, DVD+VR

DVD side

DVD Recordable/Rewritable

(DVD-R^*1/-RW, +R/+RW^*2)

• Compliant to UDF bridge

format

• DVD-RAM cannot be

played.

Dual Disc

Non-DVD side

Audio CD/CD Text (CD-DA), DTS-CD

VCD (Video CD)

CD-ROM

CD/VCD

CD-I (CD-I Ready)

CD-DA

MP3/WMA/WAV

DivX/MPEG1/MPEG2

JPEG

CD Recordable/Rewritable

(CD-R/-RW)

• Compliant to ISO 9660

level 1, level 2, Romeo,

Joliet

MPEG4

*1 DVD-R recorded in multi-border format is also playable (except for dual layer discs).

*2 It is possible to play back finalized +R/+RW (Video mode only) discs. However, the use of +R double layer disc is not

recommended.

• This unit is not compatible with Multiple

Bit Rate (MBR: a file that contains the same

DVD players and DVD Video discs have their

content encoded at several different bit rates).

own Region Code numbers. This unit can

Note on Region Code:

only play back DVD discs whose Region Code

numbers include “1.”

If you insert a DVD Video disc of an incorrect

Region Code, Region Code Error appears

on the monitor.

Disc operations 61

Download from Www.Somanuals.com. All Manuals Search And Download.

Only for CD-Text. “No Name” appears

for conventional CDs.

DTS icon (only for DTS-CDs)

Track no./Playing time

01 0:00:03

Press: Select track

Hold: Reverse/

Disc Title^*

Artist Name^*

Track Name^*

forward search^*1

MP3, WMA, WAV

Tag data will be shown instead of folder/

file names when they are recorded and

Tag Displayis set to On. ☞ [90]

Audio format

Folder no./File no./Playing time

Press: Select file

Hold: Reverse/

forward search^*1

01 0:00:03

Folder Name^*

File Name.mp3^*

∞

Press: Select folder

Hold: Display Folder

List

DivX, MPEG

Folder no./File no./Playing time

File type

Press: Select file

Hold: Reverse/

forward search^*2

01 0:00:03

Folder Name

File Name.avi

∞

Press: Select folder

Hold: Display Folder

List

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Video

Title no./Chapter no./Playing time Audio format

Press: Select

chapter

Hold: Reverse/

01 0:00:03

forward search^*1

∞

Press: Select title

DVD Audio

Group no./Track no./Playing time Audio format

BONUS indicator ☞ [68]

B.S.P indicator ☞ [68]

Press: Select track

Hold: Reverse/

01 0:00:03

forward search^*1

∞

Press: Select group

VCD

Track no./Playing time PBC indicator: lights up when PBC is in use. ☞ [67]

01 0:00:03

Press: Select track

Hold: Reverse/

forward search^*1

*1 Search speed: x2

]

x10

*2 Search speed:

] ¡

Disc operations 63

Download from Www.Somanuals.com. All Manuals Search And Download.

JPEG

Folder no.

File no.

Press: Select file

Folder Name

File Name.jpg

∞

Press: Select folder

Hold: Display Folder

List

Selecting playback modes

You can use only one of the following playback

Disc type

Repeat

modes—Intro/Repeat/Random.

Ex. To select Track Repeat

Chapter

Repeats current chapter

Title

Repeats current title

AV Menu

Mode

Repeat

Track

]

Repeats current track

]

Track

]

Repeats current track

Folder

Repeats current folder

When one of the playback modes is selected, the

corresponding indicator lights up on the disc

information screen.

Folder

Repeats current folder

To cancel, select Off in step 2.

Disc type

Intro

Repeat

Random

Track

Plays the first 15 seconds

of each track (for VCD:

PBC not in use)

Track

Disc:

Repeats current track

(for VCD: PBC not in

use)

Randomly plays all tracks

(for VCD: PBC not in

use)

Track

Plays the first 15 seconds

of each track

Track

Repeats current track

Folder

Repeats all tracks of the

current folder

Folder

Randomly plays all tracks

of current folder, then

tracks of next folders

Folder

Plays the first 15 seconds

of the first track of each

folder

Disc

Randomly plays all tracks

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting tracks on the list

Prohibiting disc ejection

If a disc includes folders, you can display the

Folder/Track Lists, then start playback.

1 Display the Folder List.

[Hold]

Eject

Folder List

My Best

1/4

Emergency Eject

No Eject

Cinema

My Best2

Pops

Favorites

020315

Set

[Hold]

2 Select No Eject

2 Select a folder, then a track.

• If you press ENT while a folder is selected, all

tracks in the selected folder are played back.

To cancel the prohibition, select Eject OK in

step 2.

You can also access the Folder List through

AV Menu

]

List.

Remote operations

Common operations

• Change the source.

• Turn off the AV function if

pressed and held.

AV/OFF

Switch to the map screen.

MAP/POS

Start playing/pause.

(For JPEG: Slide show)

ENT 6

Stop playing.

BACK/BAND

Call up AV Menu.

Adjust the volume.

VOL +/–

ATT

DISP

Attenuate/restore the sound.

Change the display. ☞ [11]

Display the on-screen bar.

[68]

☞

OSD

Change the aspect ratio of the

playback pictures.

ASPECT

Disc operations 65

Download from Www.Somanuals.com. All Manuals Search And Download.

Press: Select a chapter.

Press and hold: Reverse/forward search^*1.

Press: Select a track.

Press and hold: Reverse/forward search^*1.

4/¢

Select a title.

Select a group.

∞/5

Chapter

Title

Off

Track

Group

Off

DIRECT

(☞ below

)

Reverse/forward search^*2

Slow motion^*3during pause. (No sound can Reverse/forward search^*2

be heard.)

1/¡

Select audio language.

Select subtitle language.

Select a view angle.

—

Press: Select a track.

Press and hold: Reverse/forward search^*1

4/¢

—

Select a folder.

∞/5

Track

Off

File

Folder

Off

DIRECT

(☞ below

)

Reverse/forward search^*2

1/¡

Selecting an item with number keys

You can select a chapter/title/group/folder/

track by inputting its number.

2 Input the title number.

Ex.: To select a title of a DVD Video.

1 [twice]

On the playback screen:

• To correct a misentry, press DIRECT to

clear the entry and input again.

appears on the screen.

– –

TITLE

On the disc information screen:

The title number lights up in gray.

• Each time you press

selectable item changes. See the table

above.

, the

Download from Www.Somanuals.com. All Manuals Search And Download.

Press: Select a track.

Press and hold: Reverse/forward Press and hold: Reverse/forward Press: Select a track.

search^*4. (No sound can be heard.) search^*1. (No sound can be heard.)

Press: Select a track.

Select a folder.

Track Folder

—

Select a folder.

Off

Track

Off

File

Folder

Off

Reverse/forward search^*2

Reverse/forward search^*5(No

sound can be heard.)

Forward slow motion^*3during

pause. (No sound can be heard.)

—

Select audio language. (Only for

DivX.)

Select audio channel.

—

Select subtitle language. (Only

for DivX.)

—

*1 Search speed: x2

*2 Search speed: x2

*3 Slow motion speed: 1/32

]

x10

*4 Search speed:

*5 Search speed:

] ¡

]

x10

]

1/16

x20

]

1/8

x60

1/4

] ¡

] ¡3

]

1/2

PBC playback

Select an item on the menu.

Menu driven operations

(For DVD and DivX 6)

(only for DVD

Video and DivX)

2 Select an item you want

to play.

• To return to the previous menus, press

To cancel PBC playback

Quick skip

2 Select a track.

Return/advance the scenes by 5

minutes.

While playing...

current playback position

• To resume PBC, press

Disc operations 67

Download from Www.Somanuals.com. All Manuals Search And Download.

Special functions for DVD Audio

Operations using the on-screen bar

For DVD/VCD/DivX/MPEG/JPEG discs, you

can check the disc information and use some

functions through the on-screen bar.

Playing back a bonus group

If a DVD Audio including a “bonus group”

is detected,

lights up on the disc

1 Display the on-screen bar.

information screen.

[twice]

1 Select the bonus group.

• When you press OSD once, the

information bar appears. When you press

it again, the operation bar spreads out

below.

• The bonus group is usually recorded as

the last group.

2 Enter the key number.

2 Select an item.

• ☞ next column “To enter numbers”

• “Key number” (a kind of password) for

the bonus group is not open to public.

The way of getting the key number

depends on the disc.

3 Make a selection.

3 Follow the interactive

instructions shown on the

monitor.

If pop-up menu appears...

Selecting browsable still pictures

When a disc including browsable still pictures

• For entering time/numbers, see below.

is detected,

lights up on the disc

To remove the on-screen bar

information screen.

When disc shows the BSP selecting icons such

To enter numbers

as @ or # on the screen...

1 Select a number.

1 Select an item you want to

display.

2 Move to the next digit.

3 Repeat steps 1 and 2.

• To correct a misentry, use ¤.

• It is not necessarily required to enter trailing

zeros.

Download from Www.Somanuals.com. All Manuals Search And Download.

Information

Operation

T02-C03 TOTAL 1:25:58

C. RPT

CHAP

DVD-V

TIME

TITLE

RPT

Disc type

Pause

Stop

Audio signal format (for DVD)

PBC (for VCD)

Playback mode

Operation icons

TIME

Change time indication (☞ 5)

T. RPT Title Repeat/Track Repeat

C. RPT Chapter Repeat

F. RPT Folder Repeat

D. RND Disc Random

T. INT

Playback information

Time Search (Enter the elapsed

playing time of the current title

or of the disc.)

Title Search (by its number)

Group Search (by its number)

Chapter Search (by its number)

Track Search (by its number)

TITLE

GROUP

CHAP

TRACK

Track Intro

Current title/chapter

T02-C03

Current group/track

Current track

G02-T03

RPT

INT

Repeat play

Intro play

Random play

Change the audio language or

audio channel

TRACK 01

F001-T001

F001-F001

Current folder/track

Current folder/file

RND

Time indication

Change the subtitle language or

hide the subtitle.

Change the view angle

Elapsed playing time of the disc

TOTAL

T. REM

Remaining title/group time (for

DVD)

Remaining disc time (for others)

Elapsed playing time of the

current chapter/track

Remaining time of the current

chapter/track

^{PAGE 1/15}Change the B.S.P (for DVD

Audio) (The numbers in the

indicator show the current page/

total page number.)

TIME

REM

☞ [64]

Playback status

Play

Reverse/forward search

Reverse/forward slow-motion

Disc operations 69

Download from Www.Somanuals.com. All Manuals Search And Download.

Music server operations

The built-in HDD works not only as storage for navigation data, but as a music server, where you

can record CD tracks and music files (MP3, WMA and WAV files).

The recorded tracks are categorized into genres and albums.

You can make 99 genres in the music server, and 99 albums in each genre. Each album can contain

999 tracks.

Track 1

Album 1

Genre 1

Track 2

Track 3

Track 1

Track 2

Album 2

Genre 2

File type/Compression mode

Equalizer type ☞ [98]

Genre no./Album no./Track no./Play time

01 01 01 0:00:03

Genre Name

Album Name

Track Name

Playback mode ☞ [71]

Select “HDD.”

The last selected track starts playing from the beginning.

Select the track.

Change the track.

Change the album.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting tracks using lists

Selecting playback modes

You can use only one of the following playback

1 Call up the Genre List.

modes—Intro/Repeat/Random.

Ex. To select Track Repeat

Genre List

60’s

Jazz

Drive

AV Menu

Mode

Repeat

Track

Favorites

Classical

80’s

]

[Hold]

]

2 Select a genre, then an album.

]

When one of the playback modes is selected,

the corresponding indicator lights up on the

monitor.

• Repeat the same procedure to select the

album.

To cancel, select Off in step 2.

Track

Intro

3 Select a track to play back.

Plays the first 15 seconds

of all tracks in the current

album

Album

Plays the first 15 seconds

of the first tracks of each

album in the current genre

• If you press ENT while a genre or an

album is selected, all tracks in the selected

genre or album are played back.

Genre

Plays the first 15 seconds of

the first tracks of each genre

Track

Repeats current track

Album

Repeats all tracks of the

current album

Genre

Repeat

Random

You can also access the Genre List through

AV Menu

]

List.

Repeats all tracks of the

current genre

Album

Randomly plays all tracks of

the current album

Genre

Randomly plays all tracks of

the current genre

All

Randomly plays all tracks in

the music server

Music server operations 71

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on the name of new genres and

albums

Recording/copying tracks from a disc

• You can record tracks of audio CDs into the

• If you want to make a new genre or a new

album for the tracks to be recorded/copied,

select [New Genre] or [New Album]. To

name the new genre/album, press and hold

DISP. You can also name it later through

Title Entry (☞ [75] “Changing the titles”).

• If you do not specify a genre name or

album name on recording/copying, they are

assigned as follows.

HDD. Record appears in AV Menu

• You can copy music files (MP3, WMA, WAV)

into the HDD. Copy appears in AV Menu

Preparation:

Insert the disc to record/copy, and select DISC

as the source.

– For audio CDs, the genre name and

album name are assigned automatically

using the recording date and time.

– For music files, the genre name is

assigned automatically using the

recording date and time. The original

folder name and file name are used as

the album name and the track name.

• While recording an audio CD, you cannot

listen to the tracks being recorded with the

map screen displayed.

• While copying music files, you cannot listen

to them.

• You cannot change the source while

recording or copying tracks. If you want to

interrupt the recording and enjoy another

source, cancel the recording/copying (☞

below).

When the recording/copying is finished

Completed is displayed, and playback

resumes.

To record the current track

AV Menu

Record

Current Track

To cancel recording/copying

While recording or copying...

]

3 Start recording.

You can also cancel recording/copying

through AV Menu

]

Record

Copy

]

Recording... appears.

• The track is recorded in the High

Quality mode. (☞ next page)

• When you record a track for the first

time with this function, a new genre and

a new album is automatically created for

the track. Other tracks recorded with

this function are recorded into the same

album until you turn off the ignition

switch or edit the library.

Cancel

Download from Www.Somanuals.com. All Manuals Search And Download.

To record all the tracks in a disc

To record selected tracks

AV Menu

Record

Select All

AV Menu

Record

Select Track

]

3 Select the genre and album to

3 Select the tracks to record.

record the tracks into.

Select Track

Select All

Track 1

1/3

Select Genre

[New Genre]

Jazz

1/2

Track 2

Track 3

Drive

Track 4

Check

Favorites

Classical

[34/99]

• Checkbox operations ☞ [105]

Number of albums in the selected genre

• Repeat the same procedure to select the

album.

5 Select the genre and album to

record the tracks into.

4 Select a compression mode.

Compress

Select Genre

[New Genre]

Jazz

1/2

High Quality

Normal Quality

Drive

Favorites

Classical

[34/99]

Record

High Quality: High quality lossless

recording (LLC).

Normal Quality: More compressed

recording, so data size becomes smaller

(BSC).

Number of albums in the selected genre

• Repeat the same procedure to select the

album.

6 Select a compression mode.

Compress

5 Start recording.

High Quality

Normal Quality

Record

Recording... appears.

High Quality: High quality lossless

recording (LLC).

Normal Quality: More compressed

recording, so data size becomes smaller

(BSC).

7 Start recording.

Recording... appears.

Music server operations 73

Download from Www.Somanuals.com. All Manuals Search And Download.

To copy the current track

To copy selected tracks

AV Menu

Copy

Current Track

AV Menu

Copy

Select Track

]

3 Start copying.

3 Select the tracks to copy.

Select Track

Select All

Track 1

1/3

Track 2

Track 3

Track 4

Copying... appears.

• When you copy a track for the first time

with this function, a new genre and a

new album is automatically created for

the track. Other tracks copied with this

function are copied into the same album

until you turn off the ignition switch or

edit the library.

Check

• Checkbox operations ☞ [105]

5 Select the genre to copy the

tracks into.

To copy all the tracks in a folder

1 Select the target folder.

Select Genre

[New Genre]

Jazz

1/2

Drive

Favorites

Classical

[34/99]

AV Menu

Copy

Select All

Number of albums in the selected genre

]

6 Select the album to copy the

4 Select the genre to copy the

tracks into.

Select Genre

[New Genre]

Jazz

1/2

Drive

Favorites

Classical

[34/99]

Copying... appears, and copying starts.

Number of albums in the selected genre

5 Select the album to copy the

tracks into.

To resume the interrupted recording/copying

If have turned off the power, switched off the

car ignition switch, or detached the control

panel while recording/copying, you can resume

the last recording/copying.

• If you eject the disc or edit the library of the

music sever, Continue mode is canceled.

• You cannot use Continue if you have

canceled recording/copying manually.

Copying... appears, and copying starts.

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Select Store to finish editing.

• You cannot edit the tag data of tracks.

AV Menu

Record or Copy

Continue

]

Moving tracks between albums/Moving

albums between genres

3 Start recording/copying.

Ex. To move tracks between albums

• Select the album which the target tracks

belong to.

Recording.../Copying... appears.

Editing the library

AV Menu

Edit

Move

Track

• Library editing is possible only when HDD is

selected as the source.

]

Changing the titles

You can change the names of genres, albums

and tracks in the HDD.

Ex. To change the name of a track

3 Check the tracks to move.

Move Track

Select All

Track 1

1/2

Track 2

Track 3

Track 4

AV Menu

Title Entry

Check

]

• Checkbox operations ☞ [105]

3 Select a genre, then an album.

5 Select the album to move the

tracks into.

Move to

1/2

[New Album]

Album 1

Album 2

Album 3

Album 4

Playback of the selected item starts.

• Repeat the same procedure to select the

album.

[15/999]

Move

4 Select a track to edit.

Number of tracks in the selected album

Over the Rainbow

6 Move the selected tracks.

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

Del More Store

5 Enter the name.

• Inputting characters ☞ [105]

• You can use up to 32 characters for the

name of tracks, albums, or genres.

Music server operations 75

Download from Www.Somanuals.com. All Manuals Search And Download.

Rearranging the order of tracks, albums and

genres

Ex. To rearrange the order of tracks in an

album

Deleting tracks, albums, or genres

Ex. To delete tracks

• Select the album which the target tracks

belong to.

• Select the album which the target tracks

belong to.

AV Menu

Edit

Delete

Track

]

AV Menu

Edit

Sort

Track

]

3 Check the tracks to delete.

]

Delete Track

Select All

Track 1

1/2

3 Select the track to move.

Sort Track

Track 1

Track 2

Track 3

Track 4

Track 5

1/2

Track 2

Track 3

Track 4

Delete

Select

• Checkbox operations ☞ [105]

Select

4 Delete the selected tracks.

4 Move the selected track.

Sort Track

Track 2

Track 3

Track 1

Track 4

Track 5

1/2

[Hold]

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

Sort

A confirmation message appears. Press ENT

to confirm the operation. Press BACK to

cancel.

• To rearrange more tracks, repeat steps 1 to 4.

Checking the remaining storage size

AV Menu

Edit

HDD Free Area

]

Edit

Delete

Move

Sort

HDD Free Area

[

]

80.5% 20.0GB

Exit

Free space of the music server

Download from Www.Somanuals.com. All Manuals Search And Download.

CD changer operations

It is recommended to use a JVC MP3-compatible CD changer with your unit.

• You can play only CDs (CD-DA) and MP3 discs.

Preparation:

Make sure Changer is selected for the external input setting. (☞ [93])

Disc no./Track no./Playing time

Equalizer type ☞ [98]

01 0:00:03

Disc Title^*

Artist Name^*

Current Track^*

“No Name” appears for

conventional CDs.

Playback mode ☞ [78]

Select “CD-CH.”

To select tracks

Playback starts automatically.

Press: Select track

Hold: Reverse/forward

Display the Disc List.

Disc List

MP3 Disc

1/2

Press: Select folder (MP3

only)

Hold: Display the Disc List

Disc 02

Disc 03

Disc 04

Disc 05

Disc 06

[Hold]

On the remote:

To select a disc

• Each time you hold the button,

you can display the other list of the

remaining discs.

Select a disc to start

playing.

: Select folder

(MP3 only)

: Select track

CD changer operations 77

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting playback modes

You can use only one of the following playback

modes—Intro/Repeat/Random.

Ex. To select Track Repeat

When one of the playback modes is selected,

the corresponding indicator lights up on the

monitor.

AV Menu

Mode

Repeat

To cancel, select Off in step 2.

]

Track

Disc type

Intro

Repeat

Random

Track

Plays the first 15 seconds

of each track

Track

Repeats current track

Disc:

Randomly plays all tracks

of the current disc

Randomly plays all tracks

of all loaded discs

Disc

Repeats all tracks of the All

Plays the first 15 seconds

of the first track of all

loaded discs

current disc

Track

Plays the first 15 seconds

of each track

Track

Repeats current track

Folder

Repeats all tracks of the

current folder

Folder

Randomly plays all tracks

of current folder, then

tracks of next folders

Folder

Plays the first 15 seconds

of the first track of each

folder

Disc

Randomly plays all tracks

Disc

of the current disc

Repeats all tracks of the

Disc

current disc

All

Plays the first 15 seconds

of the first track of all

loaded discs

Randomly plays all tracks

of all loaded discs

• You can also access the Disc List through AV Menu

• While playing an MP3 disc, you can select and start playing a track in the disc using the Lists.

]

List.

Disc List

MP3 Disc

1/2

Folder List

My Best

Cinema

Pops

1/2

Track List

Song011.mp3

1/2

Disc 02

Disc 03

Disc 04

Disc 05

Disc 06

Song012.mp3

Song013.mp3

Song014.mp3

Song015.mp3

Song016.mp3

My Best2

Favorite Song

Cinema2

Download from Www.Somanuals.com. All Manuals Search And Download.

Other functions

80 iPod/D. player operations

Selecting a track from the player’s menu

Selecting playback modes

81 Playing other external

components

External input

Video input

83 Using Bluetooth® devices

—Cellular phone/audio player

Menu operation for Bluetooth devices

Registering a Bluetooth device

Using the Bluetooth cellular phone

Using the Bluetooth audio player

Phone Menu

90 AV Menu items

98 Sound equalization

Selecting an equalizer type

Storing your own adjustment

99 Additional Information

Download from Www.Somanuals.com. All Manuals Search And Download.

iPod/D. player operations

For Apple iPod and JVC D. player, it is required to connect the interface adapter (KS-PD100 for

iPod or KS-PD500 for D. player) to the CD changer jack on the rear.

Preparation:

Make sure Changer is selected for the external input setting. (☞ [93])

0:00:03

Album Name

Artist Name

Track Name

Playback mode

☞ below

Pause/Resume

Select “iPod” or “D. PLAYER.”

Playback starts automatically.

Equalizer type ☞ [98]

Select a track.

Selecting playback modes

Selecting a track from the player’s

1 Enter the player’s menu.

AV Menu

Mode

Repeat or Random

]

appears.

• This mode will be canceled if no

Repeat One

operations are done for about 5 seconds.

Functions the same as “Repeat

One” or “Repeat Mode = One.”

2 Select the desired menu item.

3 Confirm the selection.

All

Functions the same as “Repeat

All” or “Repeat Mode = All.”

Random Song

/On:

Functions the same as “Shuffle

Songs” or “Random Play =

On.”

Album

Functions the same as “Shuffle

Albums” of the iPod.

4 Repeat steps 2 and 3 to select a

track.

• When a track is selected finally, playback

starts.

• To return to the previous menu...

To cancel, select Off in step 2.

• iPod is a trademark of Apple Inc., registered

in the U.S. and other countries.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing other external components

External input

You can connect an external component to the CD changer jack on the rear using the Line Input

Adapter—KS-U57 (not supplied) or AUX Input Adapter—KS-U58 (not supplied).

Preparation:

Make sure Ext Input is selected for the external input setting. (☞ [93])

AV Input

Equalizer type ☞ [98]

Select “EXT-IN.”

Turn on the connected component and start playing the

source.

Assigning title to the external input

4 Assign a title.

• Inputting characters ☞ [105]

1 Select EXT-IN as the source.

• You can use up to 16 characters.

5 Select Store

AV Menu

Title Entry

• While driving at a speed greater than 6 mi/h

(10 km/h), operations of inputting are

prohibited.

]

Del More Store

_DownloadiP_fro_omd/_WD_w. p_wl_.a_Sy_oe_mr_ao_np_uae_lr_sa_.ct_oio_mn_.s_A/_llP_Ml_aa_ny_ui_an_lg_{s S}o_et_ah_re_cr_he_Ax_nt_der_Dn_oa_wl_nc_loo_am_d.ponents 81

Video input

You can connect an external component to the VIDEO IN plug.

Preparation:

When connecting a video component

Make sure Ext Input is selected for the external input setting, and Video for the video input

setting. (☞ [93])

• You cannot view the video picture when the parking brake is not engaged.

When connecting a camera

Make sure Camera is selected for the video input setting. (☞ [93])

Each time you press DISP, the display switches as follows:

AV screen

screen)

Vehicle information (☞ [11]

)

Video picture or camera picture

(Back to the AV

For video components:

Turn on the connected component and start playing.

To switch to the camera view automatically

You can set the unit to automatically display

the camera view when the car is put into reverse

gear or when the car slows down.

☞ [94] Interlock

To reverse the camera picture

☞ [94] Horizontal and Vertical

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Bluetooth® devices—Cellular phone/audio player

For Bluetooth operations, it is required to connect the Bluetooth Adapter (KS-BTA200) to the CD

changer jack on the rear.

• Refer also to the instructions supplied with the Bluetooth Adapter and the Bluetooth device.

• Refer to the list (included in the box) to see the countries where you may use the Bluetooth®

function.

Menu operation for Bluetooth devices

Registering a Bluetooth device

AV Menu

Mode

2/2

Mode

Dial

1/2

AV screen:

Message

Open

Bluetooth Audio

Special Device

Phone Menu

Mode

Map screen/AV

screen: other sources

than Bluetooth Audio

Dial

Message

Open

Special Device

List

[Hold]

Using the Bluetooth cellular phone

Phone Menu

Mode

Bluetooth Phone

Map screen/

AV screen

P902i

List

[Hold]

10:35 AM

Registering a Bluetooth device

Preparation:

Operate the device to turn on its Bluetooth

function.

Registration (Pairing) methods

• Use Phone Menu to register a device as a

cellular phone.

• Use AV Menu to register a device as an

audio player.

To use a Bluetooth device through the unit

(“Bluetooth Phone” and “Bluetooth Audio”) for

the first time, you need to establish Bluetooth

wireless connection between the unit and the

device.

• Once the connection is established, it is

registered in the unit even if you reset your

unit. Up to five devices can be registered in

total.

Make the unit ready to establish

a new Bluetooth connection.

Connection is established by

operating the Bluetooth device.

Open

Make the unit ready to establish

a new Bluetooth connection.

Connection is established by

operating this unit.

• Only one device for Bluetooth Phone and one

for Bluetooth Audio can be connected at a

time.

Using Bluetooth devices 83

Download from Www.Somanuals.com. All Manuals Search And Download.

Searching for available devices

To register another device after you have

registered a device, make sure New Device

is selected. (☞ [85])

Mode

]

Searching...

Registering using Open

The unit searches for available devices and

displays the list of them. (If no available

device is detected, Device Unfound

appears.)

Mode

Open

]

0000

2 Select a device you want to

connect.

Connect

2 Enter a PIN (Personal

Identification Number) code to

the unit.

3 Enter the specific PIN code of

• Inputting characters ☞ [105]

the device to the unit.

• You can enter any number you like (1-

• Inputting characters ☞ [105]

• Refer to the instructions supplied with the

device to check the PIN code.

digit to 16-digit number).

* Some devices have their own PIN code. Enter the

specified PIN code to the unit.

Connecting...

3 Select Connect

Open...

4 Use the Bluetooth device to

connect.

4 Operate the target Bluetooth

Now connection is established and you can

use the device through the unit.

device.

Enter the same PIN code (as entered in the

above step) on the device to be connected.

Now connection is established and you can use

the device through the unit.

Connecting a special device

The device remains registered even after

you disconnect the device. Use Connect

(or activate Auto Connect) to connect the

same device from next time. (☞ [89])

Mode

]

Special Device

The unit displays the list of the preset

devices.

2 Select a device you want to

connect.

3 Use Open (or Search) to

connect.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting/disconnecting a registered device

2 Select the method to make a

call.

1 On the Bluetooth Phone screen

or the Bluetooth Audio screen,

select a registered device you

want to connect/disconnect.

•

Redial: Shows the list of the phone

numbers you have dialed. Go to the

following step.

•

Received Calls: Shows the list of the

received calls. Go to the following step.

Phonebook: Shows the phone book of

the connected cellular phone. Go to the

following step.

• Each time you press 5 ∞, the

registered device names (and New

Device when a new device can be

registered) appear in turn.

•

Missed Calls: Shows the list of the

missed calls. Go to the following step.

Phone Number: Shows the phone

number entry screen. = Input numbers

and select Dial. (Inputting characters ☞

[105])

Voice (Only when the connected cellular

phone has the voice recognition system):

= Speak the name you want to call.

Mode

Connect or

Disconnect

]

• Select Connect to connect the selected

device.

•

• Select Disconnect to disconnect the

selected device.

3 Select the name/phone number

You can set the unit to connect a Bluetooth

device automatically when the unit is turned

on. (☞ [89])

you want to call.

Deleting a registered device

After step 1 above...

Mode

]

Delete Pair

Yes

]

Bluetooth icon

lights up when the adapter is connected.^*1

• To cancel, select No

Bluetooth Phone

Using the Bluetooth cellular phone

^*2P902i

Calling...

Jack

09845671234

10:35 AM

Making a call

You can make a call using one of the Dial

Menu items.

Status of the device^*3

Signal strength/Battery remainder

*1 Blue: The device is connected.

White: The device is not connected.

Cellular phone

Cellular phone with audio function

*3 Appears only when the information comes from

the device.

Phone Menu

Mode

Dial

]

Dial

Redial

1/2

Received Calls

Phonebook

Missed Calls

Phone Number

[01234567890]

Using Bluetooth devices 85

Download from Www.Somanuals.com. All Manuals Search And Download.

On the unit:

• You can also access the Dial menu by

pressing PHONE on the remote controller.

• You can also access the redial list by

pressing and holding PHONE on the

remote controller.

• You can also access the voice calling screen

by pressing and holding MENU while the

Bluetooth Phone screen is displayed.

1 Call up the preset list.

[Hold]

To adjust the volume

2 Select the preset number to call.

• This adjustment does not affect the

volume level of the other sources.

• You can adjust the microphone

volume level. ☞ [89]

Dial Preset

11122223333

22233336666

44455556666

09845671234

99988887777

55566668888

To end the call

Press and hold MENU, DISP, BACK, ENT,

∞,

or TRAFFIC.

You can also access the preset number list

through Phone Menu

]

List.

Presetting the phone numbers

You can preset up to six phone numbers.

To dial to the number acquired in Navigation

System

1 Display the phone number you

want to preset by using one of

the Dial Menu items.

1 Search for a POI or a favorite

point which has telephone

number information.

2 Call up the preset list.

[Hold]

• To preset a phone number using Phone

Number, select Store after inputting a

phone number.

0.7 mi

2 Select [Call]

3 Select a preset number.

• You cannot make an

international call through this

function.

Preset Memory

11122223333

22233336666

44455556666

09845671234

99988887777

55566668888

Store

[Hold]

You can use the following buttons on the

remote controller for the Bluetooth phone

operations.

ENT 6, PHONE: Answer the incoming

To call a preset number

On the remote:

While the Bluetooth Phone screen is displayed...

call.

End the call.

BACK:

Number keys: Enter the phone number/PIN

code.

PHONE: Call up the redial list if pressed and

held.

Download from Www.Somanuals.com. All Manuals Search And Download.

When a call comes in...

When a text message comes in...

Bluetooth Phone

If the cellular phone is compatible with text

message and Message Info is set to Auto

(☞ [89]), the unit rings and Receiving

Message appears on the monitor to inform

you of the arrival of the message.

To read the message

While Receiving Message is displayed...

P902i

Receiving Call

Jack

09845671234

10:35 AM

Name and

phone number

(if acquired)

The screen is automatically changed to

Bluetooth Phone.

When Auto Answer is activated

The unit answers the incoming calls

automatically. (☞ [89])

• You cannot edit or send a message through

the unit.

• When Auto Answer is deactivated, press

MENU, DISP, BACK, ENT,

∞

or TRAFFIC to answer the incoming

call.

Using the Bluetooth audio player

Equalizer type ☞ [98]

Reverse/forward skip

^*1Connected device^*2

Play^*3

Bluetooth icon: lights up when the adapter is Stop playback.

connected.

Audio player

Cellular phone with audio function

Select “Bluetooth

Audio.”

*2 Each time you press 5 ∞, the registered device names (and

New Devicewhen a new device can be registered) appear in

turn.

Start playback.

*3 Indicates the button pressed. It may be different from the

operation status.

• ☞ [83] for connecting a new device.

• ☞ [85] for connecting/disconnecting a

registered device.

You can use the following buttons on the

remote controller for the Bluetooth audio

operations.

• ☞ [85] for deleting a registered device.

ENT 6, BACK: Start/stop playback.

4/¢: Reverse/forward skip

VOL +/−: Adjust the volume.

Number keys: Enter the PIN code.

Using Bluetooth devices 87

Download from Www.Somanuals.com. All Manuals Search And Download.

Phone Menu

Menu items

Selectable settings

(Initial setting)

Select a phone number from the list of the phone numbers you have

dialed.

Redial

Select a phone number from the list of the received calls.

Received Calls

Phonebook

Select a name, then phone number from the phone book of the

connected cellular phone.

Select a phone number from the list of the missed calls.

Enter the phone number.

Missed Calls

Phone Number

Voice

If the connected cellular phone has the voice recognition system, you

can call by voice command.

You can read a message from the following message histories.

Unread: Messages you have not read.

Read: Messages you have read.

Message^*2

Unsent: Messages you have not sent.

Sent: Messages you have sent.

Only for New Device

Make the unit ready to establish a new Bluetooth connection. Select

this when establishing a Bluetooth connection with a device for the

first time, mainly from the device. ☞ [84]

Open^*3

• Once the connection is established, it is registered in the unit. You

can connect the unit and the device by using Connect (☞ [89])

from the next time.

Only for New Device

Make the unit ready to establish a new Bluetooth connection. Select

this when establishing a Bluetooth connection with a device for the

first time, mainly from the unit. The unit searches for available new

devices. ☞ [84]

• Before starting a search, turn on the Bluetooth function of the

device so that the unit can detect it.

Search^*3

• Once the connection is established, it is registered in the unit. You

can connect the unit and the device by using Connect (☞ [89])

from the next time.

Only for New Device

Shows the list of Bluetooth devices which requires some special

procedure to establish Bluetooth connection. Select a device you want

to connect. ☞ [84]

• After selecting the device, use Open or Search (☞ above) for

connection.

Special Device^*3

• Once the connection is established, it is registered in the unit. You

can connect the unit and the device by using Connect (☞ [89])

from the next time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Phone Menu (continued)

Menu items

Selectable settings

(Initial setting)

Only for the registered devices.

After selecting a device from among the registered devices (☞ [85,

87]), establish the connection with it. ☞ [85]

Connect^*3

Only for the device being connected.

Disconnect^*3

Disconnect the current device before connecting another device. ☞

[85]

Only for the registered devices.

Delete Pair^*3

Auto Connect

Delete the registered devices. ☞ [85]

When the unit is turned on, the connection is established

automatically with...

Off: No Bluetooth device.

Last: The last connected Bluetooth device.

Order: The available registered Bluetooth device found at first.

Auto Answer^*4

Message Info^*4

Only for the device being connected for “Bluetooth Phone.”

Off: The unit does not answer the calls automatically. Answer the call

manually.

On: The unit answers the incoming calls automatically.

Reject: The unit rejects all incoming calls.

Only for the device being connected for “Bluetooth Phone.”

Auto: The unit informs you of the arrival of a message by ringing and

displaying Receiving Message. To read the message, press ENT

(☞ [87]).

Manual: The unit does not inform you of the arrival of a message.

Only for the device being connected for “Bluetooth Phone.”

Adjust microphone volume connected to the Bluetooth adapter.

Microphone

Level^*4

The Bluetooth software and hardware version is shown.

Version

*1 Selectable items vary depending on the connected device.

*2 Selectable only when the device is compatible with text message.

*3 Also available in Modein AV Menufor Bluetooth Audio.

*4 Not selectable for New Device.

The Bluetooth word mark and logos are

Bluetooth Information:

If you wish to receive more information about

Bluetooth, visit our JVC web site.

owned by the Bluetooth SIG, Inc. and any

use of such marks by Victor Company of

Japan, Limited (JVC) is under licence. Other

trademarks and trade names are those of their

respective owners.

Using Bluetooth devices 89

Download from Www.Somanuals.com. All Manuals Search And Download.

AV Menu items

☞ [12] for the detailed Menu operations.

AV Menu

Setup

1/2

2/2

Setup

1/2

Display

Clock

Disc

Tuner

Input

Sound

Screen Control

Aspect

AV Menu

Setup

2/2

Mode

List

Others

Record

Edit

Title Entry

• The menu items shown may vary.

Menu items

Selectable settings

(Initial setting)

Language^*1

Wall Paper

English US, Español, Français

You can select the background picture of the monitor.

Default, Red, Yellow, Green, Sky, Blue, Purple,

Dark-Red, Brown, Dark-Green, Dark-Sky, Dark-

Blue

Scroll

Off: Cancels.

Once: Scrolls the display information once.

Auto: Repeats scrolling (5-second intervals).

• Holding DISP scrolls the information regardless of this

setting.

Tag Display

Dimmer

Off: Cancels.

On: Shows the Tag data while playing MP3/WMA/WAV

tracks on discs or on HDD.

Off: Cancels.

On: Activates dimmer.

Auto Dims the monitor when you turn on the headlights.

Time Set: Set the time to switch the day/night screen.

• When you choose Time Set, set the switching time on

the following screen.

*1 This setting is shared with the Languagesetting in Setup Menu (☞ [46]

)

*2 The ILLUMINATION CONTROL lead connection is required. ( Installation/Connection Manual)

☞

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

12Hours 24Hours

(Initial setting)

Time Format

Time Zone

Alaska, Pacific, Mountain, Central, Eastern,

Atlantic, Newfoundland

DST (Daylight Saving

Time)

Activate this if your residential area is subject to DST.

Off: Cancels.

Auto: Automatically applies DST when necessary.

Menu Language^*4

Select the initial disc menu language (☞ also [97]).

(

English)

Audio Language^*4

Subtitle^*4

Select the initial audio language (☞ also [97]). (English)

Select the initial subtitle language or erase the subtitle (Off

(☞ also [97]).

)

Select the on-screen language used for the external monitor

connected to the VIDEO OUT plug. (English

OSD Language

Monitor Type

)

Select the monitor type to watch a wide screen picture.

16:9: Select when the aspect ratio of the external monitor

is 16:9.

16:9

4:3 Letter Box

4:3 Letter Box/4:3 Pan Scan: Select when the

aspect ratio of the external monitor is 4:3. Refer to the

illustrations on the left to see how the pictures are shown

on the monitor.

4:3 Pan Scan

Select the position of the on-screen bar. ☞ [68]

OSD Position

: Higher position

: Lower position

Position 1 Position 2

Select playback file type when a disc contains different

types of files.

File Type

Audio: Plays back audio files.

Still Picture: Plays back JPEG files.

Video: Plays back DivX/MPEG files.

*3 Adjustable only while the source is set to DISC and playback is stopped.

*4 After you change these settings, turn off then on the power so that your setting takes effect.

AV Menu items 91

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

(Initial setting)

Select the signal format to be emitted through the

DIGITAL OUT (Optical) terminal on the rear. For details,

☞ [106].

D. Audio Output

Off: No signal is output from the terminal.

PCM Only: Select this when connecting an amplifier or a

decoder incompatible with Dolby Digital, DTS or MPEG

Audio, or connecting to a recording device.

Dolby Digital/PCM: Select this when connecting an

amplifier or a decoder compatible with Dolby Digital.

Stream/PCM: Select this when connecting an amplifier

or a decoder compatible with Dolby Digital, DTS, and

MPEG Audio.

When playing back a multi-channel DVD disc, this setting

affects the signals reproduced through the LINE OUT jacks

(and through the DIGITAL OUT terminal when PCM

Only is selected for D. Audio Output).

Down Mix

Surround Compat.: Select this when you want to enjoy

multichannel surround audio by connecting an amplifier

compatible with Dolby Surround to this receiver.

Stereo: Normally select this.

You can enjoy a powerful sound at a low volume level

while playing Dolby Digital software.

Auto: Select to apply the effect to multi-channel encoded

software.

D. Range Comp.

On: Select to always use this function.

This unit has its own Registration Code. Once you

have played back a disc in which the Registration Code

recorded, this unit’s Registration Code is overwritten for

DivX Registration

Select the format of video output according to the color

system of your external monitor.

Video Output Format

• The color system of the unit’s display is also changed.

Picture quality on the main unit’s display may deteriorate

when you select PAL

NTSC PAL

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

(Initial setting)

IF Band Width

Auto: Increases the tuner selectivity to reduce interference

noises between adjacent stations. (Stereo effect may be

lost.)

Wide: Subject to the interference from adjacent stations,

but sound quality will not be degraded and the stereo

effect will remain.

Area Setting

US: When using in North/Central/South America. AM/FM

intervals are set to 10 kHz/200 kHz.

Europe: When using in any other areas. AM/FM intervals

are set to 9 kHz/50 kHz (100 kHz during auto search).

South America: When using in South American

countries where FM interval is 100 kHz. AM interval is

set to 10 kHz.

SIRIUS ID^*5

Your SIRIUS identification number appears on the

monitor.

External Input^*6

When connecting an external component to the CD

changer jack on the rear.

Changer: CD changer, iPod, or D. player.

Ext Input: Any other than the above.

• For connecting the satellite radio tuner or the Bluetooth

Adapter, this setting is not required. It is automatically

detected.

Video Input^*7

You can determine the use of the VIDEO IN plug. ☞ [82]

Off: Select if no component is connected. (Video input is

skipped while changing the display with DISP key.)

Video: Select when connecting an AV component such as

VCR.

Camera: Select when connecting a camera.

*5 Appears only when a SIRIUS tuner is connected.

*6 Not selectable when the component connected to the CD changer jack is selected as the source.

*7 Not selectable when “EXT-IN” is selected as the source.

AV Menu items 93

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Interlock

Selectable settings

(Initial setting)

Off: Cancels.

Reverse: Automatically switch to the camera view when

the gear is shifted into reverse.

Low Speed: Automatically switch to the camera view

when your car slows down.

Horizontal adjustment is required according to how you

would like to see the picture on the monitor. Vertical

adjustment is required according to how you have installed

your camera.

Horizontal/

Vertical

Horizontal: Normal

Horizontal: Reverse

Vertical:

Normal

Vertical:

Reverse

Video Format^*10

Select the format of video input according to the color

system of the component connected to the VIDEO IN

plug.

NTSC PAL

Beep

Off: Cancels.

On: Activates the key-touch tone.

You can mute the sound of the System (AV source sounds

and voice guidance) while you talk on the cellular phone.

Off: Cancels.

Telephone Muting

Muting1 Muting2: Select either one which mute the

*11

sounds while using the cellular phone.

Select either of the two which indicates your gear direction

correctly.

Reverse Polarization

Connection^*12

GND Battery

You can check the connection status.

*8 Reverse lamp lead connection is required. (

☞

Installation/Connection Manual)

*10 Not selectable when Video Inputis set to Off.

*11 The TEL MUTING lead connection is required. ( Installation/Connection Manual)

*9 Speed signal lead connection is required. (

☞

*12 This shows the same information as Connectionin the Information Menu (☞ [43]).

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

(Initial setting)

Flat, Hard Rock, R&B, Pop, Jazz, Dance Music,

Country, Reggae, Classic, User 1, User 2,

User 3 ☞ [98]

Adjust fader—speaker output balance between the front

and rear speakers. (00

F06: front only

Fader/Balance

)

Fader/Balance

R06: rear only

F02

Exit

• When using a two-speaker system, set the fader to the

center (00).

L02

Adjust balance—speaker output balance between the left

and right speakers. (00

L06: left only

)

R06: right only

Adjust and store auto-adjustment volume level for each

source, comparing to the FM volume level. The volume

level will automatically increase or decrease when you

change the source.

Volume Adjust

–12 to +12 (00)

Adjust the settings below in the submenu:

Subwoofer

•

Phase: Subwoofer phase. Select either Normal or

Reverse, which reproduces a better sound.

•

Level: Subwoofer output level. 00 to 08 (04)

High Pass Filter

Crossover

Through: Select when the subwoofer is not connected.

On: Select when the subwoofer is connected.

Adjust the crossover frequency between the front/rear

speakers and the subwoofer.

55 Hz, 85 Hz, 125 Hz

You can change the maximum volume level of this

receiver.

Amplifier Gain

Amplifier Off: Deactivates the built-in amplifier.

Low Power: Volume 00 to 30 (Select this if the maximum

power of the speakers is less than 50 W)

High Power: Volume 00 to 50

AV Menu items 95

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

(Initial setting)

You can adjust the monitor to make it clear and legible.

• While picture from VIDEO IN is displayed, you can

adjust the playback picture of VIDEO IN (Picture

[Video]).

• While DISC is selected as the source and playback

picture is displayed, you can adjust the playback picture

of DISC (Picture [Disc]).

Screen Control/

Picture [Disc]/

Picture [Video]

• For other screens than above, Screen Control

*13

appears.

Bright^*14: Adjust if the picture is too bright or too dark.

Screen Control

–15 to +15 (00)

Color Temp.: Adjust the color temperature of the

+03

Exit

picture—warmer or cooler. –15 to +15

(

)

Contrast: Adjust the contrast. –15 to +15

(

00)

Bright

Tint: Adjust the tint if the human skin color is unnatural.

–15 to +15 (00)

•

Tint is adjustable only for VIDEO IN signal in NTSC

and discs in NTSC.

You can change the aspect ratio of the picture.

Aspect ratio of incoming signal

4:3 16:9

Full

For 16:9 original

pictures

Aspect [Disc]/

Aspect [Video]

Regular

For 4:3 original

pictures

• For “DISC”: Aspect ratio is

automatically selected to match

to the incoming signals.

Auto

• For the other video sources:

Aspect ratio is fixed to Full

*13 The settings of Screen Controlare also applied to the map screen and screens of Navigation Menus.

*14 This setting in Screen Controlis shared with Brightnesssetting in SetupMenu (☞ [44]).

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Selectable settings

(Initial setting)

Mono

Only for FM. (Off

Only for FM. (DX

On) ☞ [54]

DX / Local

SSM

Local) ☞ [54]

Only for FM. ☞ [52]

Only for disc playback, music server, CD changer and

iPod/D. player. ☞ [64, 71, 78, 80]

Intro/Repeat/Random

The accessible lists differ depending on the sources.

To record audio CDs into the music server. ☞ [72, 73]

To copy music files into the music server. ☞ [74]

To edit the tracks in the music server. ☞ [75]

☞ [54, 75, 81]

List

Record

Copy

Edit

Title Entry

*15 For the menu items in Modefor Bluetooth Audio, ☞ [88, 89]

Language codes (for DVD/DivX language selection)

Code Language

Afar

Persian

Finnish

Fiji

Faroese

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

Kirghiz

Latin

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay (MAY)

Maltese

Burmese

Nauru

Nepali

Norwegian

Occitan

(Afan) Oromo

Oriya

Panjabi

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

Rumanian

Kinyarwanda

Sanskrit

Sesotho

Sundanese

Swahili

Tamil

Telugu

Tajik

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali, Bangla

Tibetan

Breton

Catalan

Corsican

Czech

Welsh

Bhutani

Greek

Esperanto

Estonian

Basque

Thai

Tigrinya

Turkmen

Tagalog

Setswana

Tonga

Turkish

Tsonga

Tatar

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Indonesian

Icelandic

Hebrew

Yiddish

Javanese

Georgian

Kazakh

Sindhi

Sangho

Serbo-Croatian

Singhalese

Slovak

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Siswati

Twi

Ukrainian

Urdu

Uzbek

Vietnamese

Volapuk

Wolof

Xhosa

Yoruba

Zulu

AV Menu items 97

Download from Www.Somanuals.com. All Manuals Search And Download.

Sound equalization

Selecting an equalizer type

Storing your own adjustment

You can store your adjustment into User 1

User 2, and User 3

AV Menu

1 Repeat steps 1 and 2 above, then

]

in step 3...

EQ - Flat

Settings

1/3

Flat

Hard Rock

R&B

Pop

Jazz

Frequency

60 Hz

Store

Exit

3 Select an equalizer type.

2 Adjust.

Select the frequency.

Adjust the level.

Preset equalizing values

60 150 400

2.4

Equalizer type

Flat

Hz Hz Hz kHz kHz kHz kHz

00 00 00 00 00 00 00

+03 +03 +01 00 00 +02 +01

+03 +02 +02 00 +01 +01 +03

00 +02 00 00 +01 +01 +02

+03 +02 +01 +01 +01 +03 +02

+04 +02 00 –02 –01 +01 +01

+02 +01 00 00 00 +01 +02

+03 00 00 +01 +02 +02 +03

+02 +03 +01 00 00 +02 00

00 00 00 00 00 00 00

3 Store the setting into User 1

User 2 or User 3

Hard Rock

R&B

EQ - Store To

User 1

User 2

User 3

Pop

Jazz

Dance Music

Country

Reggae

Classic

User 1/2/3

Store

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Information

General

Listening to the radio

Storing stations in memory

• When SSM is over, all previously stored

stations are erased and stations are stored

newly.

• There is a time limit for some operations.

In this case, if no further operation is done

for a certain period, the current operation is

canceled.

• By pressing SRC or MAP on the unit, you

can also turn on the power. The map screen

is displayed at turn-on if you press MAP, and

an AV screen if you press SRC. If the source is

ready, playback starts.

• You cannot select some sources if they are not

ready.

• When SSM is over, received stations are

preset in No. 1 (lowest frequency) to No. 6

(highest frequency), and preset station No. 1

is tuned in.

• When storing a station manually, a previously

preset station is erased when a new station is

stored in the same preset number.

– SAT/CD-CH/iPod/D. PLAYER: cannot

be selected without connecting the target

source component.

– DISC: cannot be selected if a disc is not in

the loading slot.

– EXT-IN: cannot be selected without

selecting Ext Input for the External

Input setting. (☞ [93])

Satellite radio operations

• You can also connect the JVC SIRIUS radio

PnP (Plug and Play), using the JVC SIRIUS

radio adapter, KS-U100K (not supplied) to

the CD changer jack on the rear.

By turning on/off the power of the unit, you

can turn on/off the JVC PnP. However, you

cannot control it from this unit.

• To know more about SIRIUS Satellite radio or

to sign up, visit <http://www.sirius.com>.

• For the latest channel listings and

programming information, or to sign up

for XM Satellite radio, visit <http://www.

xmradio.com>.

– Bluetooth Audio: cannot be selected if a

Bluetooth adapter is not connected.

• If you turn off the power while DISC is

selected as the source, disc play will start

automatically next time you turn on the

power.

• The voltage and the speed on the vehicle

information screen may be different from the

actual values.

Sound equalization / Additional information 99

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Recordable/Rewritable discs

• This unit can recognize a total of 3 500 files

and 250 folders (a maximum of 999 files per

folder).

• If no playable files are recorded in a folder, the

folder will not be recognized.

Disc operations

General

• In this manual, words “track” and “file” are

interchangeably used.

• This unit can also play back 8 cm discs.

• This unit can only play back audio CD

(CD-DA) files if different type of files are

recorded in the same disc.

• On some discs, the actual operations may

be different from what is explained in this

manual.

• This unit can display only one-byte

characters. No other characters can be

correctly displayed.

• Reverse search stops automatically when it

reaches the beginning of the disc. Playback

resumes at normal speed.

• No sound comes out during slow motion

playback. When playing a VCD, reverse slow

motion playback is prohibited.

• When playing a DVD/VCD, no sound comes

out during Search.

• For some DVDs and VCDs, changing the

subtitle language, audio language (or audio

channel) without using the disc menu is

prohibited.

• Use only “finalized” discs.

• This unit can play back multi-session discs;

however, unclosed sessions will be skipped

while playing.

• This unit may be unable to play back some

discs or files due to their characteristics or

recording conditions.

• This unit can recognize a total 25 characters

for file/folder names.

• For DVD-R/DVD-RW: This receiver can

play only discs recorded in the DVD-Video

format. (Discs recorded in the DVD-VR

format cannot be played.)

• DVD-RWs or CD-RWs may require a longer

readout time since the reflectance of DVD-

RW and CD-RW is lower than that of regular

discs.

• Do not use discs on which labels can be

directly printed by an ink jet printer. Using

these discs under high temperatures or high

humidity may cause malfunctions or damages

to discs.

Inserting a disc

• When a disc is inserted upside down, Disc

Error appears on the monitor. Eject the disc.

Playing DivX files

• This unit can play back DivX files with

the extension code <.divx>, <.div>, <.avi>

(regardless of the letter case—upper/lower).

• This unit supports the DivX files whose

resolution is 720 x 576 pixels or less.

• This unit supports DivX 6.x, 5.x, 4.x, and 3.11.

• Audio stream should conform to MP3 or

Dolby Digital.

Ejecting a disc

• If the ejected disc is not removed within

15 seconds, the disc is automatically inserted

again into the loading slot to protect it from

dust.

• If the control panel is left open for a while, it

closes automatically.

Changing the source

• If you change the source, playback also stops

without ejecting the disc.

Next time you select “DISC” for the playback

source, disc play starts from where it has been

stopped previously.

• When a disc has been loaded, selecting

“DISC” for the playback source starts disc

play.

• This unit does not support GMC (Global

Motion Compression).

• The file encoded in the interlaced scanning

mode may not be played back correctly.

• This unit can display a unique registration

code—DivX Video On Demand (DRM—

Digital Rights Management). For activation

and more detail, visit <www.divx.com/vod>.

100

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing MPEG files

• This unit can play back files recorded in VBR

(variable bit rate).

• This unit can play back MPEG files with the

extension code <.mpg> or <.mpeg>.

• The stream format should conform to MPEG

system/program stream.

• The file format should be MP@ML (Main

Profile at Main Level)/SP@ML (Simple Profile

at Main Level)/MP@LL (Main Profile at Low

Level).

• Audio streams should conform to MPEG1

Audio Layer-2.

Playing JPEG files

• It is recommended that you record a file at

640 x 480 resolution.

• This unit can play back baseline JPEG files.

Progressive JPEG files or lossless JPEG files

cannot be played.

Files recorded in VBR have a discrepancy in

elapsed time indication.

• This unit cannot play back the following files

and skips them when playing back files:

– MP3 files encoded with MP3i and

MP3 PRO format.

– MP3 files encoded in an unappropriated

format.

– MP3 files encoded with Layer 1/2.

– WMA files encoded with lossless,

professional, and voice format.

– WMA files which are not based upon

Windows Media® Audio.

– WMA DRM (Digital Rights

Management).

– Files which have the data such as AIFF,

ATRAC3, etc.

– WMA files encoded with MBR (Multiple

Bit Rate) format.

– AAC files.

– OGG files.

Playing MP3/WMA/WAV files

• This unit can play back files with the

extension code <.mp3>, <.wma>, or <.wav>

(regardless of the letter case—upper/lower).

• This unit can show ID3 Tag Version

1.0/1.1/2.2/2.3/2.4 (for MP3). This unit can

also show WAV Tag and WMA Tag.

• This unit can play back the files meeting the

conditions below:

– Bit rate: MP3/WMA: 32 kbps - 320 kbps

– Sampling frequency:

48 kHz, 44.1 kHz, 32 kHz (for MPEG1)

24 kHz, 22.05 kHz, 16 kHz (for MPEG2)

48 kHz, 44.1 kHz, 32 kHz (for WMA)

44.1 kHz (for WAV)

– Disc format: ISO 9660 Level 1/ Level 2,

Romeo, Joliet, Windows long file name

Additional information 101

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen guide icons

During play, the following guide icons may

appear for a while on the monitor.

Control screen

• The following control screens appear only

on the external monitor.

Appears at the beginning of a scene

containing multi-subtitle languages

(for DVD only).

DivX/MPEG/JPEG/MP3/WMA/WAV

Appears at the beginning of a scene

containing multi-audio languages (for

DVD only).

Appears at the beginning of a scene

containing multi-angle views (for DVD

only).

T. RPT

TIME 00:00:14

Folder :

2 / 3

Track : 6 / 14 (Total 41)

01 Music

02 Music

03 Music

Cloudy.mp3

Fair.mp3

Fog.mp3

Hail.wma

Indian summer.mp3

Rain.mp3

Shower.mp3

Snow.mp3

Thunder.wma

Typhoon.mp3

Wind.mp3

Track Information

Album

Weather

Artist

Robert M. Smith

Title

Rain

Playback

Pause

Winter sky.mp3

Forward slow motion playback (for

DVD and VCD only)

Reverse slow motion playback (for

DVD only)

Forward search

Reverse search

Current folder (highlighted bar)

Current folder number/total folder number

Folder list

Selected playback mode

Elapsed playing time of the current track (not

displayed for JPEG)

Operation status

Current track number/total number of tracks

in the current folder (total number of tracks

on the disc)

Track information (only for MP3/WMA/WAV)

Track list

Current track (highlighted)

TIME

00:14

T. RPT

Track : 6 / 14

Cloudy

Fair

Fog

Hail

Indian summer

Rain

Shower

Snow

Thunder

Typhoon

Wind

Track Information

Album

Four seasons

Artist

Robert M. Smith

Title

Winter sky

Rain

Selected playback mode

Elapsed playing time of the current track

Operation status

Current track number/total number of tracks

on the disc

Track information

Track list

Current track (highlighted bar)

102

Download from Www.Somanuals.com. All Manuals Search And Download.

Music server operations

iPod/D. player operations

• Sound quality may deteriorate if you select

Normal Quality for recording mode.

• While recording, recorded sounds are

reproduced from the speakers. When

recording is stopped, CD original sounds are

reproduced.

• When you turn on this unit, the iPod or

D. player is charged through this unit.

• The text information may not be displayed

correctly. This unit can display up to 40

characters.

• The items in the player’s top menu are as

follows:

• You cannot change the source while recording

or copying tracks.

For iPod:

• This system uses SCMS (Serial Copy

Management System) which allows only

first-generation digital copies to be made of

premastered software such as regular CDs. If

you try to record from a duplicated CD-R/

-RW, SCMS Cannot Copy may appear on

the display then recording will be cancelled.

• Text data in the CD Text cannot be recorded

into the HDD.

Playlists Ô Artists Ô Albums Ô Songs

Ô Genres Ô Composers Ô (back to

the beginning)

For D. player:

Playlist Ô Artist Ô Album Ô Genre

Ô Track Ô (back to the beginning)

Notice:

When operating an iPod or a D. player, some

operations may not be performed correctly

or as intended. In this case, visit the following

JVC web site:

• Play time indication may advance unstably

on the monitor while recording. This is not a

malfunction of this unit.

For iPod users: <http://www.jvc.co.jp/

english/car/support/ks-pd100/index.html>

For D. player users: <http://www.jvc.co.jp/

english/car/support/ks-pd500/index.html>

• You cannot edit the Tag data of tracks in the

HDD.

• While the System is moving, rearranging or

deleting items in the library, no sound comes

out, and you cannot change the playback

source.

• When you move, rearrange or delete items in

the library, the playback mode is canceled.

Additional information 103

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Bluetooth devices

AV Menu items

General

• If you change the Amplifier Gain setting

from High Power to Low Power while the

volume level is set higher than 30, the unit

automatically changes the volume level to

• While driving, do not perform complicated

operation such as dialing the numbers, using

phone book, etc. When you perform these

operations, stop your car in a safe place.

• Some Bluetooth devices may not be connected

to this unit depending on the Bluetooth

version of the device.

• This unit may not work for some Bluetooth

devices.

• Connecting condition may vary depending on

circumstances around you.

Volume 30

• After you change any of Menu Language

Audio Language

Subtitle settings, turn

off then on the power, and re-insert the disc

(or insert another disc) so that your setting

takes effect.

• When the language you have selected is not

recorded on a disc, the original language is

automatically used as the initial language. In

addition, for some discs, the initial languages

settings will not work as you set due to their

internal disc programming.

• When you select 16:9 for a picture whose

aspect ratio is 4:3, the picture slightly changes

due to the process for converting the picture

width.

• When the unit is turned off, the device is

disconnected.

Icons for phone types

• These icons indicate the phone type set on the

device.

: Cellular phone

: Household phone

: Office

• Even if 4:3 Pan Scan is selected, the screen

size may become 4:3 Letter Box for some

discs.

: General

: Other than above

Warning messages for Bluetooth operations

•

Connection Error : The device is registered

but the connection has failed. Use Connect

to connect the device again. (☞ [85])

Error : Try the operation again. If Error

appears again, check if the device supports the

function you have tried.

•

Device Unfound : No available Bluetooth

device is detected by Search

Loading : The unit is updating the phone

book and/or a text message.

Please Wait... : The unit is preparing to

use the Bluetooth function. If the message

does not disappear, turn off and turn on the

unit, then connect the device again (or reset

the unit).

•

Reset 08 : Check the connection between

the adapter and this unit.

104

Download from Www.Somanuals.com. All Manuals Search And Download.

Inputting characters

Checkbox operations

Ex.:

- Input Genre Name -

Select Track

Select All

Track 1

1/3

Track 2

Track 3

Track 4

Check

Del More Store

To select an item in the list

Enter a space

Move the cursor

Display other keyboards

Delete a character

• Each time you press ENT, the checkbox

alternates between checked (selected) and

not checked (not selected).

Select a character on the

keyboard

To select all the items in the list

Select Select All and press ENT.

• When you have selected all the items, the

top item in the list changes to Deselect

All. To remove all the item from

selection, select Deselect All and press

ENT.

Enter the selected character

To display other keyboards

• Each time you press the button, the

keyboard changes cyclically. By pressing

and holding the button, you can change

the keyboards in the reverse direction.

Characters available for word entry

In addition to the roman alphabet (A – Z, a – z),

the following characters can be used to input

various information.

To delete all the characters

Select Del and hold ENT.

• While driving at a speed greater than 6 mi/h

(10 km/h), operations of inputting are

prohibited.

space

Additional information 105

Download from Www.Somanuals.com. All Manuals Search And Download.

About sounds reproduced through the rear terminals

• Through the analog terminals (Speaker out/LINE OUT):

2-channel signal is emitted. When playing a multi-channel encoded disc, multi-channel signals are

downmixed. (☞ [92] Down Mix.)

• Through DIGITAL OUT (optical):

Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted through this terminal.

To reproduce multi-channel sounds such as Dolby Digital, DTS, and MPEG Audio, connect an

amplifier or a decoder compatible with these multi-channel sources to this terminal, and set D.

Audio Output correctly. (☞ below.)

Output signals through the DIGITAL OUT terminal

Output signals are different depending on the D. Audio Output setting (☞ [92]).

D. Audio Output

Dolby Digital/

PCM Only

Stream/PCM

PCM

Playback disc

48 kHz, 16/20/24 bits

Linear PCM

48 kHz, 16 bits stereo Linear PCM*

48 kHz, 16 bits stereo Linear PCM

96 kHz, Linear PCM

DVD

Video

48 kHz, 16 bits stereo

Linear PCM

48 kHz, 16 bits stereo Linear PCM

with Dolby Digital

Dolby Digital bitstream

with DTS

with MPEG Audio

DTS bitstream

MPEG bitstream

44.1/88.2/176.4 kHz,

16/20/24 bits Linear

PCM

44.1 kHz, 16 bits stereo Linear PCM

48/96/192 kHz,

16/20/24 bits Linear

PCM

DVD

Audio

48 kHz, 16 bits stereo Linear PCM

48 kHz, 16 bits stereo

Linear PCM

with Dolby Digital

with DTS

Dolby Digital bitstream

48 kHz, 16 bits stereo Linear PCM

DTS bitstream

44.1 kHz, 16 bits stereo Linear PCM

48 kHz, 16 bits stereo Linear PCM

48 kHz, 16 bits stereo

Linear PCM

Audio CD, Video CD

Audio CD with DTS

with Dolby Digital

DTS bitstream

Dolby Digital bitstream

DivX

with MPEG Audio

MPEG

MP3/WMA

WAV

32/44.1/48 kHz, 16 bits Linear PCM

44.1/48 kHz, 16 bits Linear PCM

32/44.1/48 kHz, 16 bits Linear PCM

44.1 kHz, 16 bits stereo Linear PCM

While playing some DVDs, digital signals may be emitted at 20 bits or 24 bits (at their original bit rate) through the

DIGITAL OUT terminal if the discs are not copy-protected.

106

Download from Www.Somanuals.com. All Manuals Search And Download.

Information

108 Maintenance

109 Troubleshooting

117 Specifications

107

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the

connectors.

To minimize this possibility, periodically wipe

the connectors with a cotton swab or cloth

moistened with alcohol, being careful not to

damage the connectors.

How to handle discs

Center

holder

When removing a disc from its

case, press down the center holder

of the case and lift the disc out,

holding it by the edges.

• Always hold the disc by the

edges. Do not touch its recording surface.

When storing a disc into its case, gently insert

the disc around the center holder (with the

printed surface facing up).

• Make sure to store discs into the cases after

use.

To keep discs clean

A dirty disc may not play correctly.

If a disc does become dirty, wipe it

with a soft cloth in a straight line

from center to edge.

Connectors

• Do not use any solvent (for

example, conventional record cleaner, spray,

thinner, benzine, etc.) to clean discs.

Moisture condensation

Moisture may condense on the lens inside the

DVD/CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Should this occur, the DVD/CD player may

malfunction. In this case, eject the disc and

leave the unit turned on for a few hours until

the moisture evaporates.

To play new discs

New discs may have some rough

spots around the inner and outer

edges. If such a disc is used, this

unit may reject the disc.

To remove these rough spots, rub

the edges with a pencil or ball-point pen, etc.

To clean the unit

When the unit is very dirty, wipe with a

well-wrung cloth dipped in a kitchen cleanser

(neutral) thinned by water and then go over the

same surface with a dry cloth.

(Since there is the possibility of water drops

getting inside of the unit, do not directly apply

cleanser to the surface.)

Do not use the following discs:

Warped disc

Sticker

Sticker residue

Stick-on label

108

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service

center.

Symptoms

Causes/Remedies

Some operations are prohibited without the

parking brake engaged. Park the car in a safe place

before the operations.

•

Parking Brake appears on the

monitor.

• Sound cannot be heard from the

speakers.

• Adjust the volume to the optimum level.

• Check the cords and connections.

• The monitor is not clear and legible for Sunshine from the windshield may cause this

watching the playback picture or the

map.

symptom. Adjust Bright and Contrast of

Screen Control. (☞ [96]).

The internal temperature is too low. Leave the

power on, and wait until the internal temperature

rises and the indication goes off.

•

Low Temperature/HDD Warming

Up appears and some functions do not

work properly.

Something is blocking the control panel

movement. Remove the obstacle, then reset the

unit (☞ [4]).

• If this does not work, check if the installation

has been correctly done.

Push Reset appears on the display,

and the control panel movement is

freezed.

• The unit does not work at all.

Reset the unit (☞ [4]).

• Cannot operate some functions of an

AV source on the map screen.

On the map screen, you can operate only some

limited functions of the current source. Press SRC

to display the AV screen and operate the source.

• Cannot operate AV sources with the

remote controller on the map screen.

On the map screen, 4¢5∞ keys of the

remote controller always works for scrolling the

map.

• Route calculation seems to have

stopped.

Route calculation may take long depending on the

route. Wait for a while.

• Navigation voice cannot be heard from Guidance voice level is set to the minimum level.

the speakers.

Adjust it to the optimum level. (☞ [43])

• Voice guidance are not heard while

viewing an AV screen.

Interruption is set to Off. Set it to On to allow

the voice guidance interrupt the AV source. (☞

[44])

• The voice guidance does not come out

from the speaker on the driver’s side.

Change the Output Channel setting. (☞ [43])

• Cannot scroll the map to northeast, etc.

To scroll to northeast, you need to press 5 and

¢ at the same time.

Maintenance / Troubleshooting 109

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

• Navigation guidance is incorrect.

Installation angle setting is not correct. Set it

correctly. (☞ [46])

• Navigation guidance is sometimes

incorrect.

Reversing signal/speed signal wires are not

connected. Connect them correctly (☞

Installation/Connection Manual—separate

volume).

• Navigation guidance is hard to listen to. Surround noise interferes. Increase the voice

cruise level. (☞ [44])

Failed to calculate the route. Select another

destination/via point.

•

Route Calculation Error. appears

on the monitor.

Valid information is not available in the database.

Search for another place.

City not found.

not found. Valid information not

found. Coordinate information

Street/Center

not found. or Street not found.

appears on the monitor.

This is not a malfunction. The system may also

search areas around the selected city/state.

• A POI found using Category in the

Destination Menu is not within the

selected city/state.

You tried to save a route in an existing name.

Select another name.

•

The route name already exists.

appears on the monitor.

Delete some routes and save the new one.

No valid traffic information is available now.

Check the connection information of the leads

No space to store the new

route. appears on the monitor.

There are no valid traffic

information. appears on the monitor.

• The current position displayed on the

map remains wrong for more than 30

minutes.

below. (☞ [43] Connection

)

– GPS antenna

– Speed signal lead

– Reverse gear signal lead

If any disconnection is found, connect the lead

again.

• If no problems are found with connections,

reset the calibration data. (☞ [46] Reset

Calibration

)

110

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

• SSM automatic presetting does not

work.

Store stations manually (☞ [53]).

• Static noise while listening to the radio. Connect the antenna firmly.

Start subscribing to SIRIUS Satellite Radio (☞

[55]).

•

CALL 1-888-539-SIRIUS TO

SUBSCRIBE appears on the monitor.

Move to an area where signals are stronger.

No Signal or NO SIGNAL appears on

the monitor.

Connect the antenna firmly.

No Antenna or CHECK ANTENNA

appears on the monitor.

No broadcast on the selected channel.

Select another channel or continue listening to the

previous channel.

Invalid Channel appears on the

monitor for about 5 seconds, then

returns to the previous display when

listening to the SIRIUS Satellite radio.

Selected channel is no longer available or is

unauthorized. Select another channel or continue

listening to the previous channel.

•

CHANNEL– – – appears on the

display for about 2 seconds, then

returns to the previous channel while

listening to the XM Satellite radio.

No text information for the selected channel.

•

NO NAME appears on the monitor.

The unit is updating the channel information and

it takes a few minutes to complete.

Channels Updating XX%

completed (for SIRIUS) or

UPDATING (for XM) appear son the

monitor.

Selected channel is not broadcasting at this time.

Select another channel or continue listening to the

previous channel.

The unit is loading the channel information

and audio. Text information are temporarily

unavailable.

•

OFF AIR appears on the display while

listening to the XM Satellite Radio.

LOADING appears on the display

while listening to the XM Satellite

Radio.

Reconnect this unit and the Satellite Radio

correctly and reset this unit.

Reset 08 appears on the display.

• Satellite Radio does not work at all.

Reconnect the Satellite radio after a few seconds.

• Disc can be neither recognized nor

played.

Eject the disc forcibly (☞ [4]).

• Disc cannot be ejected.

Unlock the disc (☞ [65]).

• Recordable/Rewritable discs cannot be • Insert a finalized disc.

played back.

• Tracks on the Recordable/Rewritable

discs cannot be skipped.

• Finalize the discs with the component which

you used for recording.

Troubleshooting 111

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

The format of the disc is supported.

Insert the disc correctly again.

•

Not Support appears on the monitor.

Disc Error appears on the monitor.

The player may have malfunctioned. Eject the disc

forcibly.

Eject Error or Loading Error

appears on the monitor.

• Sound and pictures are sometimes

interrupted or distorted.

• Stop playback while driving on rough roads.

• Change the disc.

• No playback picture appears on the

monitor.

Parking brake wire is not connected properly. (☞

Installation/Connection Manual.)

• No sound is heard while playing back a Some DVD Audios prohibit downmixed output.

DVD Audio.

When you play back such a disc, the unit plays

back the right front and left front signals only.

Region code is not correct (☞ [61]).

•

Region Code Error appears on the

monitor when you insert a DVD Video.

• Disc cannot be played back.

• Change the disc.

• Record the tracks using a compliant application

in the appropriate discs (☞ [61]).

• Add appropriate extension codes to the file

names.

• WMA track cannot be played back, and The track is copy-protected with DRM.

skipped.

• Noise is generated.

The track played back is not a playable file. Skip to

another file.

• Tracks are not played back as you have Playback order may differ from the one played

intended.

back using other players.

• A longer readout time is required.

Readout time varies due to the complexity of the

folder/file configuration. Do not use too many

hierarchies and folders.

• Elapsed playing time is not correct.

This sometimes occurs during playback. This is

caused by how the tracks are recorded.

• Correct characters are not displayed

(e.g. album name).

This unit can only display alphabets (A – Z, a

– z), numbers, and a limited number of symbols

and some accented letters. Available characters ☞

[105]

Insert a disc that contains tracks of proper

formats.

•

No Files appears on the monitor.

112

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

• Sound does not come out while

copying music files.

This is not a malfunction.

• Sound does not come out in the map

screen while recording a CD.

This is not a malfunction.

• Cannot change the source while

recording/copying.

This is not a malfunction. If you want to enjoy

another source, cancel recording/copying and

change the source.

• Edited track name is not displayed.

Tag information instead of the track name is

displayed. Set Tag Display to Off to display the

track name. (☞ [90])

No track is stored in the HDD.

•

No Music appears on the monitor.

The selected item contains no tracks/albums.

Select another.

No Track or No Album appears on

the monitor.

The selected album is full. Select another album.

•

Cannot record tracks over. or

Cannot copy tracks over. appears

on the monitor.

Record only xx/XX tracks. or

Copy only xx/XX tracks. appears

on the monitor.

The selected album cannot contain all the

tracks you wanted to record/copy. Press ENT to

continue recording/copying, or press BACK to

select another album.

The selected album/genre cannot contain all the

items you wanted to move. Press ENT to continue

moving the items, or press BACK to select

another album/genre.

•

Move only xx/XX tracks? or

Move only xx/XX albums?

appears on the monitor.

The capacity of the target storage you have

selected is already full. Delete the unwanted items

in the target storage to make an enough space.

•

HDD Full, Track Full, Album

Full, or Genre Full appears on the

monitor.

Recording is failed due to the external influences

such as vibration, shaking of the car. Try to record

once more while driving on a paved road. If the

trouble still persist, consult your dealer.

Write Error/Read Error appears

and CD recording is canceled.

You have tried to copy non-original disc. Copy its

original disc.

•

SCMS cannot Copy appears.

The format of the track is not supported.

Not Supported appears on the

monitor.

The selected track does not exist in the HDD.

Not Playable appears on the

monitor.

Troubleshooting 113

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

• Insert a disc into the magazine.

• A disc is inserted upside down. Insert the disc

correctly.

•

No Disc appears on the monitor.

Insert the magazine.

•

No Magazine appears on the

monitor.

Disc does not include playable files. Replace the

disc with playable files.

Connect this unit and the CD changer correctly

and press the reset button of the CD changer.

No Files appears on the monitor.

Reset 08 appears on the monitor.

Press the reset button of the CD changer.

Reset 01 Reset 07 appears on the

•

–

monitor.

• The CD changer does not work at all.

Reset the unit (☞ [4]).

• The iPod or D. player does not turn on • Check the connecting cable and its connection.

or does not work.

• Charge the battery.

• For D. player: Update the firmware version.

• The sound is distorted.

Deactivate the equalizer either on this unit or the

iPod/D. player.

Check the connecting cable and its connection.

•

Disconnect appears on the monitor.

• For iPod: Playback stops.

The headphones are disconnected during

playback. Restart playback.

• No sound can be heard when

connecting an iPod nano.

Disconnect the headphones from the iPod nano.

• No sound can be heard.

Disconnect the adapter from the D. player. Then,

connect it again.

•

ERROR 01 appears on the monitor

when connecting a D. player.

No tracks are stored. Import tracks to the iPod or

D. player.

No Files or No Track appears on

the monitor.

Disconnect the adapter from both this unit and

iPod/D. player. Then, connect it again.

Reset 01 Reset 07 appears on the

–

monitor.

Check the connection between the adapter and

this unit.

Reset 08 appears on the monitor.

• The iPod’s or D. player’s controls do

not work after disconnecting from this

unit.

Reset the iPod or D. player.

114

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptoms

Causes/Remedies

• Bluetooth device does not detect the

unit.

This unit can be connected with one Bluetooth

cellular phone and one Bluetooth audio device at a

time. While connecting a device, this unit cannot

be detected from another device. Disconnect

currently connected device and search again.

• The unit does not detect the Bluetooth • Check the Bluetooth setting of the device.

device.

• Search from the Bluetooth device. After the

device detects the unit, select Open on the unit

to connect the device. (☞ [84])

• The unit does not make pairing with

the Bluetooth device.

• Enter the same PIN code for both the unit and

target device.

• Select the device name from Special Device

then try to connect again. (☞ [84])

• Echo or noise occurs.

Adjust the microphone unit position.

• Phone sound quality is poor.

• Place the Bluetooth audio device nearer to the

adapter.

• Move the car to place where you can get a better

signal reception.

• The sound is interrupted or skipped

during playback of a Bluetooth audio

device.

• Place the Bluetooth audio device nearer to the

adapter.

• Disconnect the device connected for “Bluetooth

Phone.”

• Turn off, then turn on the unit.

• (When the sound is not yet restored,) connect

the device again.

• The connected audio device cannot be Check whether the connected audio device

controlled.

supports AVRCP (Audio Video Remote Control

Profile).

For Bluetooth operations, refer also to the instructions supplied with the Bluetooth Adapter.

Troubleshooting 115

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback sources

Dolby Digital

Compressed digital audio, developed by

Dolby Laboratories, which enables multi-

channel encode to create the realistic

surround sound.

Glossary

Navigation System

GPS

Global Positioning System. By receiving the

GPS signals from the satellites, the Navigation

System determines the position of the car.

DTS

Compressed digital audio, developed by

Digital Theater Systems, Inc., which enables

multichannel like Dolby Digital. As the

compression ratio is lower than for Dolby

Digital, it provides wider dynamic range and

better separation.

Linear PCM

Uncompressed digital audio, the same format

used for CDs and most studio masters.

POI

Points of Interest. You can select your

destinations by selecting from the

categories—such as business centers,

shopping centers.

TMC

Traffic Message Channel. Traffic messages

transmitted by some VHF broadcasters via

RDS signals. Using this data, the Navigation

System informs you of road conditions.

MPEG Audio

Another compressed digital audio which also

enables multi-channel encode to create the

realistic surround sound.

Via Point

A location through which you reach your final

destination. For this Navigation System, you

can determine nine locations through which

you can reach your final destination.

On-screen guide

While operating the built-in DVD/CD

player, operation modes are displayed on the

monitor. (☞ [102])

UDF-Bridge Format

A hybrid file system used to provide

compatibility with ISO 9660 for accessing

any type of files on the disc. (UDF stands for

Universal Disk Format.)

WMA

Windows Media Audio. A compression

process developed by Microsoft® for

compressing audio data (i.e. music).

116

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

L1, C/A code

System & Service

Global Positioning System

Standard Positioning Service

15-channel multi-channel reception system

1 575.42 MHz

Reception System

Reception Frequency

Sensitivity

–130 dBm

1/second, continuous

Update Rate

Polarization

Right Handed Circular Polarization

GPS Antenna

Dimensions (approx.) 30.4 mm × 11.7 mm × 35.5 mm

(W × H × D)

Cable (approx.)

(1-1/4 inches × 1/2 inch × 1-7/16 inches)

5.0 m (16.4 feet)

Attachment mat size

(approx.)

70 mm × 70 mm (2-13/16 inches ×

2-13/16 inches)

20 W RMS × 4

Power Output

Channels at 4 Ω and

≤ 1% THD+N

80 dBA (reference:

1 W into 4 Ω)

Signal to Noise Ratio

Load Impedance

4 Ω (4 Ω to 8 Ω allowance)

Frequencies

Level

60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz,

6 kHz, 12 kHz

10 dB

Equalizer Control Range

Line-Out Level/

Impedance

Audio output level

2.5 V/20 kΩ load (full scale)

Output Impedance

Signal wave length

Output level

1 kΩ

660 nm

–21 dBm to –15 dBm

NTSC

Digital (DIGITAL OUT:

Optical)

Color system

Video output (composite)

Video input (composite)

Other Terminals

1 Vp-p/75 Ω

VIDEO IN, steering wheel remote input

Input

Output

VIDEO OUT, LINE OUT (FRONT),

LINE OUT (REAR), SUBWOOFER OUT

Others

CD changer

Specifications 117

Download from Www.Somanuals.com. All Manuals Search And Download.

FM (with channel

interval set to 100 kHz

or 200 kHz):

87.5 MHz to 107.9 MHz

Frequency Range

FM (with channel

87.5 MHz to 108.0 MHz

530 kHz to 1 710 kHz

531 kHz to 1 602 kHz

interval set to 50 kHz):

AM (with channel

interval set to 10 kHz):

AM (with channel

interval set to 9 kHz):

Usable Sensitivity

FM Tuner

11.3 dBf (1.0 μV/75 Ω)

16.3 dBf (1.8 μV/75 Ω)

50 dB Quieting

Sensitivity

Alternate Channel

Selectivity (400 kHz)

65 dB

Frequency Response

Stereo Separation

Capture Ratio

Sensitivity

40 Hz to 15 000 Hz

40 dB

1.5 dB

20 μV

AM Tuner

Selectivity

65 dB

Non-contact optical pickup

(semiconductor laser)

Signal Detection System

2 channels (stereo)

16 Hz to 20 000 Hz

Number of Channels

Frequency Response

DVD, fs=48 kHz/

96 kHz

DVD, fs=192 kHz

VCD/CD

16 Hz to 20 000 Hz

96 dB

Dynamic Range

98 dB

Signal-to-Noise Ratio

Wow and Flutter

Less than measurable limit

Max. Resolution

720 x 480 pixels (30 fps)

720 x 576 pixels (25 fps)

DivX

Video

Bit Rate

32 Kbps – 320 Kbps

Audio

Sampling Frequency

MPEG-1: 32 kHz, 44.1 kHz, 48 kHz

MPEG-2: 16 kHz, 22.05 kHz, 24 kHz

Max. Resolution

720 x 480 pixels (30 fps)

720 x 576 pixels (25 fps)

32 Kbps – 384 Kbps

MPEG Video

Video

Audio

Bit Rate

Sampling Frequency

MP3 (MPEG Audio Layer 3)

WMA (Windows Media® Audio)

32 kHz, 44.1 kHz, 48 kHz

Max. Bit Rate: 320 Kbps

118

Download from Www.Somanuals.com. All Manuals Search And Download.

40 GB (Map data: 16 GB / Storage: 24 GB)

HDD

Max. Bit Rate: 320 kbps

MP3 (MPEG Audio Layer 3)

WMA (Windows Media® Audio)

3.5 inch wide liquid crystal display

Screen size

224 640 pixels: 320 (horizontal) × 3 × 234 (vertical)

TFT (Thin Film Transistor) active matrix format

NTSC

16:9 (wide)

Number of Pixel

Drive Method

Color System

Aspect Ratio

Operating Voltage

DC 14.4 V (11 V to 16 V allowance)

Negative ground

Power Requirement

Grounding System

–10°C to +60°C (14°F to 140°F)

0°C to +40°C (32°F to 104°F)

–300 m to +3 000 m (–980 feet to +9 800

feet)

Allowable Storage Temperature

Allowable Operating Temperature

Allowable Operating Altitude

Installation Size

182 mm × 52 mm × 158 mm

(7-3/16 inches × 2-1/16 inches × 6-1/4

inches)

Dimensions (approx.)

(W × H × D)

Panel Size

188 mm × 58 mm × 12 mm

(7-7/16 inches × 2-5/16 inches × 1/2 inch)

2.2 kg (4.9 lbs) (excluding accessories)

Mass (approx.)

Design and specifications are subject to change without notice.

If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality

shop.

• DivX, DivX Ultra Certified, and associated

logos are trademarks of DivX, inc. and are

used under license.

• Microsoft and Windows Media are either

registered trademarks or trademarks of

Microsoft Corporation in the United States

and/or other countries.

• Official DivX® Ultra Certified product

• “DVD Logo” is a trademark of DVD Format/

Logo Licensing Corporation registered in the

US, Japan and other countries.

• Manufactured under license from Dolby

Laboratories. Dolby and the double-D symbol

are trademarks of Dolby Laboratories.

• Plays all versions of DivX® video (including

DivX® 6) with enhanced playback of DivX®

media files and the DivX® Media Format

• “DTS” is a registered trademark of DTS, Inc.

and “DTS 2.0 + Digital Out” is a trademark of

DTS, Inc.

Specifications 119

Download from Www.Somanuals.com. All Manuals Search And Download.

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Still having trouble??

USA ONLY

Call 1-800-252-5722

http://www.jvc.com

We can help you!

EN, SP, FR

0707NSMMDWJEIN

Download from Www.Somanuals.com. All Manuals Search And Download.

KD-NXD505

Installation/Connection Manual

Manual de instalación/conexión

Manuel d’installation/raccordement

0707NSMMDWJEIN

EN, SP, FR

LVT1774-002A

[J]

ENGLISH

ESPAÑOL

FRANÇAIS

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical

systems. If your vehicle does not have this system, a voltage inverter is

required, which can be purchased at JVC car audio dealers.

Esta unidad está diseñada para funcionar con 12 V de CC, con sistemas

eléctricos de masa NEGATIVA. Si su vehículo no posee este sistema,

será necesario un inversor de tensión, que puede ser adquirido en los

concesionarios de JVC de equipos de audio para automóviles.

Cet appareil est conçu pour fonctionner sur des sources de courant continu de

12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce type d’alimentation,

il vous faut un convertisseur de tension, que vous pouvez acheter chez un

revendeur d’autoradios JVC.

WARNINGS

ADVERTENCIAS

AVERTISSEMENTS

• DO NOT install any unit in locations where:

•

NO instale la unidad en los siguientes sitios:

• N’INSTALLEZ aucun appareil dans les endroits suivants où:

– il peut gêner l’utilisation du volant ou du levier de vitesse.

– il peut gêner le fonctionnement de dispositifs de sécurité tels que les coussins

de sécurité.

– it may obstruct the steering wheel and gearshift lever operations.

– it may obstruct the operation of safety devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving. If you need to operate the unit

while driving, be sure to look ahead carefully.

• The driver must not watch the monitor while driving.

• This unit has a built-in HDD, which is a device to read minute magnetic

changes. The inside of the device is precision components, requiring you to

notice the following when installing the unit:

Install the unit at a place where the following conditions are satisfied:

– Dry and neither too hot nor too cold—between 5°C (41°F) and 35°C

(95°F). If the temperature is too low, the HDD will not work. Wait until

the temperature in the car becomes normal before operating the unit.

– At an altitude between –300 m (–980 ft) below sea level and +3000 m

(9800 ft) above sea level.

– puede obstaculizar las maniobras del volante de dirección y de la palanca

de cambios.

– puede obstaculizar la operación de los dispositivos de seguridad, como

por ejemplo, bolsas de aire.

– il peut gêner la visibilité.

– Donde pueda obstruir la visibilidad.

• NE manipulez pas l’appareil quand vous conduisez. Si vous devez commander

l’appareil pendant que vous conduisez, assurez-vous de bien regarder devant vous.

• Le conducteur ne doit pas regarder le moniteur lorsqu’il conduit.

• Cet appareil contient un disque dur intégré, qui est dispositif permettant de

lire les charges magnétiques minuscules. L’intérieur de l’appareil est composé

de dispositifs de précision, vous demandant de prendre les précautions

suivantes lors de l’installation de l’appareil:

Installez l’appareil dans un endroit où les conditions suivantes sont satisfaites:

– Sec et ni trop chaud ni trop froid—entre 5°C (41°F) et 35°C (95°F). Si la

température est trop basse, le disque dur ne fonctionne pas. Attendez que la

température dans la voiture redevienne normale avant d’utiliser l’appareil.

– À une altitude située entre –300 m (–980 pied) au-dessous du niveau de la

mer et +3000 m (9800 pied) au-dessus du niveau de la mer.

– Avec une ventilation suffisante pour éviter tout échauffement interne de

l’appareil.

•

NO opere la unidad mientras maneja. Si es necesario operar la unidad

mientras maneja, asegúrese de no apartar la vista de la carretera.

El conductor no debe mirar el monitor mientras conduce.

Esta unidad dispone de un HDD incorporado, que es un dispositivo que

lee los cambios magnéticos diminutos. En el interior del dispositivo hay

componentes de precisión y por lo tanto, se deberá tener en cuenta lo

siguiente al instalar la unidad.

•

Instale la unidad en un lugar que cumpla con las siguientes condiciones:

– Nivelado y seco, ni demasiado frío ni demasiado caluroso—entre 5°C (41°F)

y 35°C (95°F). El HDD no funcionará si la temperatura es muy baja. Antes de

operar la unidad, espere hasta que la temperatura del habitáculo se normalice.

– A una altitud entre –300 m (–980 pie) por debajo del nivel del mar y

+3000 m (9800 pie) por encima del nivel del mar.

– With adequate ventilation to prevent internal heat buildup in the unit.

– Con una ventilación adecuada para evitar la generación de calor en el

interior de la unidad.

Parts list for installation and connection

Lista de piezas para instalación y conexión

Liste des pièces pour l’installation et raccordement

The following parts are provided for this unit. If anything is missing, contact Con esta unidad se suministran las siguientes piezas.

Les pièces suivantes sont fournies avec cet appareil.

Après vérification, veuillez les placer correctement.

your dealer immediately.

Después de inspeccionarlas, colóquelas correctamente.

A / B

Trim plate

Placa de guarnición

Plaque d’assemblage

Power cord

Cordón de alimentación

Cordon d’alimentation

AV I/O cords

Hard case/Control panel

Estuche duro/Panel de

control

Sleeve

Cubierta

Manchon

Crimp connectors

Conectores de sujeción

Raccord à sertir

Cables de E/S AV

Cordons entrée/sortie audio-vidéo

Etui de transport/Panneau

de commande

Mounting bolt—

M5 x 20 mm

Batteries

Pilas

Q/R

Washer (ø5)

Arandela (ø5)

Rondelle (ø5)

Rubber cushion

Cojín de goma

Amortisseur en

caoutchouc

Remote controller/Holder

Control remoto/Soporte

Télécommande/Support

Extension leads

Cable prolongador

Cordon rallonge

GPS antenna/Attachment mat

Antena GPS/Estera de fijación

Antenne GPS/Feuille de fixation

Measuring gauge

Calibrador de

medición

(M5 x 13/16")

Piles

Perno de montaje—

M5 x 20 mm

Gabarit de mesure

RM-RK250

Lock nut (M5)

Tuerca de seguridad (M5)

Ecrou d’arrêt (M5)

(M5 x 13/16 pulgada)

Boulon de montage—

M5 x 20 mm

Handles

Manijas

Poignées

R03(UM-4)/

AAA(24F) x 2

(M5 x 13/16 pouces)

Double-sided adhesive tape

Cinta adhesiva de doble cara

Ruban adhésif double face

Required space for installation / Espacio requerido para la instalación / Espace

nécessaire pour l’installation

Installing the remote controller/

Instalación del control remoto/

Installation de la télécommande

Caution when installing / Precaución en la

instalación / Précautions lors de l’installation

• You cannot install the unit on the

car which has any obstacles in the

diagonally shaded areas.

3 mm (1/8")

6 mm (1/4")

Dashboard

Fit the unit into the mounting sleeve

by using four corners of the trim

plate.

• DO NOT press the panel (shaded

in the illustration).

Introduzca el receptor en la manga

de montaje utilizando las cuatro

esquinas de la placa decorativa.

Holder/Soporte/Support

Tablero de instrumentos

Tableau de bord

•

No es posible instalar la unidad en el

coche si hay obstáculos en las zonas

sombreadas laterales.

Trim plate is detached on this illustration

for explanation.

Para fines explicativos, se ha retirado la

placa de guarnición en esta ilustración.

La plaque de garniture est montrée

détachée sur cette illustration pour les

besoins de l’explication.

• Vous ne pouvez pas installer l’unité

dans une voiture comportant des

obstacles dans les zones ombrées sur

l’illustration.

•

NO presione el panel (sombreado en la ilustración).

Fixez l’autoradio sur le manchon de montage en utilisant les

quatre coins de la plaque de garniture.

• NE POUSSEZ PAS sur le panneau (en gris sur l’illustration).

Remote controller

Control remoto

Télécommande

Control panel

Panel de control

Panneau de commande

5 mm (1/4")

TROUBLESHOOTING

• The fuse blows.

LOCALIZACION DE AVERIAS

• El fusible se quema.

EN CAS DE DIFFICULTES

• Le fusible saute.

* Are the red and black leads connected correctly?

* ¿Están los conductores rojo y negro correctamente conectados?

* Les fils rouge et noir sont-ils racordés correctement?

• Power cannot be turned on.

• No es posible conectar la alimentación.

• L’appareil ne peut pas être mise sous tension.

* Is the yellow lead connected?

* ¿Está el cable amarillo conectado?

* Le fil jaune est-elle raccordée?

• No sound from the speakers.

• No sale sonido de los altavoces.

• Pas de son des enceintes.

* Is the speaker output lead short-circuited?

* ¿Está el cable de salida del altavoz cortocircuitado?

* Le fil de sortie d’enceinte est-il court-circuité?

• Sound is distorted.

• El sonido presenta distorsión.

• Le son est déformé.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

* ¿Está el cable de salida del altavoz conectado a masa?

* ¿Están los terminales “–” de los altavoces L y R conectados a una masa

común?

* Le fil de sortie d’enceinte est-il à la masse?

* Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la

masse?

• Noise interfere with sounds.

• Perturbación de ruido.

• Interférence avec les sons.

* Is the rear ground terminal connected to the car’s chassis using shorter and

thicker cords?

* ¿El terminal de tierra trasero está conectado al chasis del automóvil utilizando * La prise arrière de mise à la terre est-elle connectée au châssis de la voiture

los cordones más corto y más grueso?

avec un cordon court et épais?

• No playback picture appears while an AV source is selected.

• No aparece la reproducción de imágenes mientras se selecciona la

fuente de AV.

* ¿Se ha conectado correctamente el cable del freno de estacionamiento?

• Aucune image de lecture n’apparaît lors de la sélection d’une

source audio-vidéo.

* Le fil de sortie du frein de stationnement est-il connecté correctement?

* Is the parking brake lead properly connected?

• Unit becomes hot.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• La unidad se calienta.

• L’appareil devient chaud.

* ¿Está el cable de salida del altavoz conectado a masa?

* ¿Están los terminales “–” de los altavoces L y R conectados a una masa

común?

* Le fil de sortie d’enceinte est-il à la masse?

* Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la

masse?

• This unit does not work at all.

* Have you reset your unit?

• Este receptor no funciona en absoluto.

• Cet appareil ne fonctionne pas du tout.

* ¿Reinicializó el receptor?

* Avez-vous réinitialisé votre appareil?

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (IN-DASH MOUNTING)

INSTALACION (MONTAJE EN EL TABLERO DE

INSTRUMENTOS)

INSTALLATION (MONTAGE DANS LE TABLEAU

DE BORD)

The following illustration shows a typical installation. If you have any

questions or require information regarding installation kits, consult your JVC

car audio dealer or a company supplying kits.

La siguiente ilustración muestra una instalación típica. Si tiene alguna pregunta L’illustration suivante est un exemple d’installation typique. Si vous avez des

o necesita información acerca de las herramientas para instalación, consulte

con su concesionario de JVC de equipos de audio para automóviles o a una

compañía que suministra tales herramientas.

questions ou avez besoin d’information sur des kits d’installation, consulter votre

revendeur d’autoradios JVC ou une compagnie d’approvisionnement.

• Si l’on n’est pas sûr de pouvoir installer correctement cet appareil, le faire

installer par un technicien qualifié.

• Lors de l’installation assurez-vous de ne pas bloquer le ventilateur à l’arrière

afin de permettre une ventilation correcte.

• If you are not sure how to install this unit correctly, have it installed by a

qualified technician.

• Make sure not to block the fan on the rear panel to maintain proper

ventilation when installed.

•

Si usted no está seguro de cómo instalar correctamente la unidad, hágala

instalar por un técnico cualificado.

•

Asegúrese de no bloquear las rendijas de ventilación del panel trasero, para

poder mantener una buena ventilación una vez instalado.

Do the required electrical connections.

Realice las conexiones eléctricas requeridas.

Réalisez les connexions électriques.

Do not block the fan.

No tape las rendijas de ventilación.

Ne bloquez pas le ventilateur.

Bend the appropriate tabs to hold the sleeve firmly

in place.

Doble las lengüetas apropiadas para retener

firmemente la manga en su lugar.

Tordez les languettes appropriées pour maintenir le

manchon en place.

When you stand the unit, be careful not to damage the fuse on the rear.

Al poner la unidad vertical, tenga cuidado de no dañar el fusible provisto en la

parte posterior.

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager

le fusible situé sur l’arrière.

When installing the unit without using the sleeve / Instalación de la unidad sin utilizar la cubierta / Lors de

l’installation de l’appareil sans utiliser de manchon

When using the optional stay / Cuando emplea un soporte

opcional / Lors de l’utilisation du hauban en option

In a car having the “Required space for installation” (see page 1), first remove the car radio and install the unit in its place.

En un automóvil que dispone del “Espacio requerido para la instalación” (véase página 1), primero desmonte el autorradio e instale la unidad en su lugar.

Dans une voiture possédant l’“Espace nécessaire pour l’installation” (voir page 1), retirez d’abord l’autoradio d’origine et installer cet appareil à sa place.

Fire wall

Tabique a prueba de incendios

Cloison

Stay (option)

Soporte (opción)

Hauban (en option)

Flat type screws—M5 x 8 mm

Not included for this unit.

No suministrado con esta unidad.

(M5 x 3/8") ^*2

Tornillos tipo plano—M5 x 8 mm

(M5 x 3/8 pulgada) ^*2

Vis à tête plate—M5 x 8 mm

(M5 x 3/8 pouces) ^*2

Non fourni avec cet appareil.

Dashboard

Tablero de

Bracket ^*2

Ménsula ^*2

Support ^*2

Flat type screws—M5 x 8 mm

(M5 x 3/8") ^*2

instrumentos

Tableau de bord

Screw (option)

Tornillo (opción)

Vis (en option)

Tornillos tipo plano—M5 x 8 mm

(M5 x 3/8 pulgada) ^*2

Bracket ^*2

Ménsula ^*2

Support ^*2

Vis à tête plate—M5 x 8 mm

(M5 x 3/8 pouces) ^*2

Note

When installing the unit on the mounting bracket, make sure to use the 8 mm (3/8") -long screws. If longer screws are used,

they could damage the unit.

Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 8 mm (3/8 pulgada) de longitud. Si se

utilizan tornillos más largos, éstos pueden dañar la unidad.

Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 8 mm (3/8 pouces). Si

des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Nota

Remarque

Install the unit at an angle of less than 30˚ vertically and of less than 5˚ horizontally.

Assembling the measuring gauge / Montaje del calibrador de medición / Assemblage

du gabarit de mesure

• After installation, confirm the vertical angle of the unit using the supplied measuring gauge.

Instale la unidad a un ángulo de menos de 30° en sentido vertical, y de menos de 5° en sentido horizontal.

•

Después de la instalación, confirme el ángulo vertical de la unidad con el calibrador de medición suministrado.

Installez l’appareil avec un angle vertical de moins de 30˚ et un angle horizontal de moins de 5˚.

• Après l’installation, vérifiez l’angle vertical de l’appareil en utilisant le gabarit de mesure fourni.

8˚

3˚

7˚

-5

28˚

23˚

7˚

30˚

-5˚

• Keep the gauge handy for the future use.

Mantenga a mano el calibrador para uso futuro.

5˚

•

• Conservez le gabarit à portée de main pour une utilisation future.

Measuring the installation angle

Medición del ángulo de instalación

Mesure de l’angle d’installation

BEFORE starting, make sure...

• You have parked the car where it cannot be inclined. (It

should be parked horizontally.)

ANTES de empezar, compruebe que...

AVANT de commencer, assurez-vous que...

• Vous avez garé votre voiture dans un endroit où elle n’est

pas inclinée. (Elle doit être garée horizontalement.)

•

Ha estacionado el automóvil en un sitio no inclinado.

(Estacionar sobre una superficie plana.)

1 Detach the control panel.

2 Measure the angle.

1 Desmonte el panel de control.

2 Mida el ángulo.

1 Détachez le panneau de commande.

2 Mesurez l’angle.

• Attach the measuring gauge closely and flatly to the

•

Acople el patrón de medida de forma que quede plano

• Attachez le gabarit de mesure étroitement et à plat sur

l’unité principale (partie ombrée sur l’illustration de

gauche).

main unit (to the portion shaded in the illustration on

the left).

y cerca de la unidad principal, en la parte sombreada

que se muestra en la parte izquierda de la ilustración.

3 Note your measured angle.

1: –5.0 to 1.0˚

3 Anote el ángulo medido.

1: –5,0 a 1,0˚

3 Notez l’angle mesuré.

1: –5,0 à 1,0˚

2: 1.0 to 6.0˚

2: 1,0 a 6,0˚

2: 1,0 à 6,0˚

3: 6.0 to 14.0˚

3: 6,0 a 14,0˚

4: 14,0 a 32,0˚^*

3: 6,0 à 14,0˚

4: 14.0 to 32.0˚^*

4: 14,0 à 32,0˚^*

It is not recommended to install the main unit at an

Se recomienda no instalar la unidad principal a un

Il n’est pas recommandé d’installer l’apareil avec un

angle of more than 30˚; otherwise, the malfunction

may result.

ángulo de más de 30° pues de lo contrario, podrían

producirse fallos de funcionamiento.

angle de plus de 30˚; sinon, cela peut entraîner un

mauvais fonctionnement.

When you use the Navigation System for the first time after

installation...

Follow the procedure described on pages 8 and 9 of the

INSTRUCTIONS (separate volume).

Cuando utilice el sistema de navegación por primera vez

después de la instalación...

Realice el procedimiento descrito en las páginas 8 y 9 del

MANUAL DE INSTRUCCIONES (volumen separado).

Quand vous utilisez l’autoradio pour la première fois après

l’installation...

Suivez la procédure décrite aux pages 8 et 9 du MANUEL

D’INSTRUCTIONS (volume séparé).

Measure this angle.

Mida este ángulo.

Mesurez cet angle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Removing the unit

Extracción de la unidad

Retrait de l’appareil

Before removing the unit, release the rear section.

Antes de extraer la unidad, libere la sección trasera.

Avant de retirer l’appareil, libérer la section arrière.

Insert the two handles, then pull them as

illustrated so that the unit can be removed.

Inserte las dos manijas y, a continuación,

extráigalas de la manera indicada en la

ilustración para poder desmontar la unidad.

Insérez les deux poignées, puis tirez de la façon

illustrée de façon à retirer l’appareil.

Installing the GPS antenna

• People who use pacemakers should avoid a physical contact with the

magnetic antenna and should not handle it themselves. This causes

malfunctions of the pacemakers.

• Keep the magnetic antenna away from the storage media such as disks,

credit cards; otherwise, its data will be collapsed.

• The antenna should be attached so firmly that it cannot be detached in the

event of a collision or sudden braking.

Instalación de la antena GPS

Installation de l’antenne GPS

• Les personnes utilisant un stimulateur cardiaque doivent éviter tout contact

physique avec l’antenne magnétique et ne doivent pas la manipuler elles-

même. Cela pourrait entraîner un dysfonctionnement du stimulateur

cardiaque.

•

Las personas portadoras de marcapasos deben evitar el contacto físico con

la antena magnética, y deben abstenerse de intentar su manejo. Esto puede

producir un fallo de funcionamiento en el marcapasos.

•

Mantenga la antena magnética alejada de los medios de almacenaje como

por ejemplo disquetes, tarjetas de crédito, y otros, pues se dañarán los datos. • Tenez l’antenne magnétique à distance des supports de mémoire tels que les

Sujete la antena firmemente, para evitar que se salga en el caso eventual de

un choque o de un frenado brusco.

disques, les cartes de crédit; sinon, les données pourraient être corrompues.

• L’antenne doit être fixée suffisamment solidement pour qu’elle ne puisse pas se

détacher en cas de choc ou de coup de frein brutal.

Å Inside the car

Å Dentro del automóvil

Å À l’intérieur de la voiture

Beneath a non-metallised^*window, fix the

attachment mat (R) on the dashboard, then place

the antenna (Q) on the mat.

Detrás de un cristal no metalizado^*, fije la estera

de fijación (R) sobre el cubretablero y ponga la

antena (Q) sobre la estera.

Derrière une fenêtre non métallisée^*, fixez la feuille

de fixation (R) sur le tableau de bord, puis placez

l’antenne (Q) sur la feuille.

• Make sure that the antenna is not covered by

any components and parts of the car and it can

receive the signals from all directions.

•

Asegúrese de no tapar la antena con ningún

componente ni pieza del automóvil, y de que la

recepción de la señal es posible desde todas las

direcciones.

• Assurez-vous que l’antenne n’est recouverte

par aucun composant ou aucune partie de la

voiture et peut recevoir les signaux de toutes les

directions.

The windows with screen antenna, windshield

heating or thermally insulated screens will

interfere with GPS reception, and will degrade

the reliability of the Navigation System.

Las ventanillas que cuentan con antenas con

pantalla, calefacción en el cristal del parabrisas o

pantallas térmicamente aisladas interfieren con

la recepción GPS, y disminuirán la confiabilidad

del sistema de navegación.

Les vitres avec une antenne incrustée, les

chauffages de pare-brise ou les écrans d’isolation

thermique interfèrent avec la réception GPS et

réduisent la fiabilité du système de navigation.

ı Outside the car

ı Fuera del automóvil

ı À l’extérieur de la voiture

Fix the antenna (Q) to a pre-washed, flat, metallic Fije la antena (Q) sobre una superficie metálica

Fixez l’antenne (Q) sur une surface métallique

plate.

surface.

plana, previamente lavada.

• Wire the antenna cord so as not to allow the rain

to leak in.

•

Procure tender el cable de antena para no

permitir la entrada de lluvia.

• Câblez le cordon d’antenne de façon à empêcher

la pluie de pénétrer à l’intérieur.

• The antenna magnetically attached will be

used even at a speed of 180 km/h (110 mi/h)

(maximum). The antenna must be specially

secured for higher speeds.

• Detach the antenna before you wash the car with

the car-wash facilities.

•

La antena fijada magnéticamente puede

utilizarse incluso a velocidades del orden de

180 km/h (110 mi/h) (máximo). Para velocidades

superiores, la antena deberá estar especialmente

asegurada.

• Une fois fixée, l’antenne magnétique ne se

détachera pas même à une vitesse de 180 km/h

(110 mi/h) (maximum). L’antenne doit être fixée

spécialement pour les vitesses plus élevées.

• Détachez l’antenne avant de laver votre voiture

dans un poste de lavage.

•

Desmonte la antena antes de lavar el automóvil

en un lavacoches automático.

ELECTRICAL CONNECTIONS

CONEXIONES ELECTRICAS

RACCORDEMENTS ELECTRIQUES

To prevent short circuits, we recommend that you disconnect the battery’s

Para evitar cortocircuitos, recomendamos que desconecte el terminal negativo Pour éviter tout court-circuit, nous vous recommandons de débrancher la borne

negative terminal and make all electrical connections before installing the unit. de la batería y que efectúe todas las conexiones eléctricas antes de instalar la

négative de la batterie et d’effectuer tous les raccordements électriques avant

d’installer l’appareil.

• Be sure to ground this unit to the car’s chassis again after

installation.

unidad.

• Asegúrese de volver a conectar a masa esta unidad al chasis del

automóvil después de la instalación.

• Assurez-vous de raccorder de nouveau la mise à la masse de cet

appareil au châssis de la voiture après l’installation.

Notes:

Notas:

Remarques:

• Replace the fuse with one of the specified rating. If the fuse blows frequently,

consult your JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more

than 50 W (both at the rear and at the front, with an impedance of 4 Ω to

8 Ω). If the maximum power is less than 50 W, change “Amplifier Gain”

setting to prevent the speakers from being damaged (see page 95 of the

INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with

insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when

removing this unit.

•

Reemplace el fusible por uno con la corriente especificada. Si el fusible se

quemase frecuentemente consulte con su concesionario de JVC de equipos

de audio para automóviles.

• Remplacer le fusible par un de la valeur précisée. Si le fusible saute souvent,

consulter votre revendeur d’autoradios JVC.

• Il est recommandé de connecter des enceintes avec une puissance de plus

de 50 W (les enceintes arrière et les enceintes avant, avec une impédance

comprise entre 4 Ω et 8 Ω). Si la puissance maximum est inférieure à 50 W,

changez “Gain amplific.” pour éviter d’endommager vos enceintes (voir page

95 du MANUEL D’INSTRUCTIONS).

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS

UTILISÉS avec de la bande isolante.

• Le dissipateur de chaleur devient très chaud après usage. Faire attention de ne

pas le toucher en retirant cet appareil.

•

Se recomienda conectar los altavoces con una potencia máxima de más

de 50 W (tanto atrás como adelante, con una impedancia de 4 Ω a 8 Ω).

Si la potencia máxima es de menos de 50 W, cambie “Gcia.amplific.” para

evitar daños en los altavoces (consulte la página 95 del MANUAL DE

INSTRUCCIONES).

•

Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.

El sumidero térmico estará muy caliente después del uso. Asegúrese de no

tocarlo al desmontar esta unidad.

Heat sink

Sumidero térmico

Dissipateur de chaleur

PRECAUTIONS on power supply and speaker

connections:

PRECAUCIONES sobre las conexiones de la fuente de

alimentación y de los altavoces:

PRECAUTIONS sur l’alimentation et la connexion des

enceintes:

• DO NOT connect the speaker leads of the power cord to the car

battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers,

check the speaker wiring in your car.

• NO conecte los conductores de altavoz del cable de alimentación a

la batería de automóvil, pues podrían producirse graves daños en la

unidad.

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à

la batterie; sinon, l’appareil serait sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux

enceintes, vérifiez le câblage des enceintes de votre voiture.

•

ANTES de conectar a los altavoces los conductores de altavoz del cable de

alimentación, verifique el conexionado de altavoz de su automóvil.

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

ESPAÑOL

FRANÇAIS

Typical Connections / Conexiones tipicas / Raccordements typiques

Before connecting: Check the wiring in the vehicle carefully. Incorrect

connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car body

may be different in color.

Antes de la conexión: Verifique atentamente el conexionado del vehículo.

Una conexión incorrecta podría producir daños graves en la unidad.

Los cordones del cable de alimentación y los del conector procedentes de la

carrocería del automóvil podrían ser de diferentes en color.

Avant de commencer la connexion: Vérifiez attentivement le câblage du

véhicule. Une connexion incorrecte peut endommager sérieusement l’appareil.

Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la

voiture peuvent être différents en couleur.

1 Connect the colored leads of the power cord in the order

1 Conecte los conductores de color del cable de alimentación en 1 Connectez les fils colorés du cordon d’alimentation dans l’ordre

specified in the illustration below.

el orden especificado en la ilustración de abajo.

spécifié sur l’illustration ci-dessous.

2 Connect the antenna cord and the GPS antenna.

3 Finally connect the wiring harness to the unit.

2 Conecte el cable de antena y la antena GPS.

3 Por último, conecte el cable de alimentación a la unidad.

2 Connectez le cordon d’antenne et l’antenne GPS.

3 Finalement, connectez le faisceau de fils à l’appareil.

GPS antenna

Antena GPS

Antenne GPS

REVERSE GEAR SIGNAL (see diagram / véase diagrama / voir le diagramme

SPEED SIGNAL (see diagram / véase diagrama / voir le diagramme

)

Radio antenna

VIDEO OUT (see diagram / véase diagrama / voir le diagramme

VIDEO IN (see diagram / véase diagrama / voir le diagramme

OE REMOTE

)

Antena de radio

Antenne radio

)

DIGITAL OUT (see diagram

/ véase diagrama / voir le

diagramme

)

Steering wheel remote input/ Entrada del control remoto del volante de dirección/ Entrée de la télécommande de volant (see

Rear ground

terminal

Terminal de tierra

posterior

Borne arrière de

masse

diagram / véase diagrama / voir le diagramme

)

15 A fuse

Fusible de 15 A

Fusible 15 A

Not included for this unit

No suministrado con esta unidad

To an external component (see diagram and

)

Non fourni avec cet appareil

Ignition switch

Interruptor de encendido

Interrupteur d’allumage

A un componente externo (véase diagrama

Black

Negro

Noir

Pour connecter un appareil extérieur (voir le

diagramme et

)

To metallic body or chassis of the car

A un cuerpo metálico o chasis del automóvil

Vers corps métallique ou châssis de la voiture

Yellow ^*2

Amarillo ^*2

Jaune ^*2

To a live terminal in the fuse block connecting to the car battery (bypassing the

ignition switch) (constant 12 V)

A un terminal activo del bloque de fusibles conectado a la batería del automóvil

(desviando el interruptor de encendido) (12 V constantes)

A une borne sous tension du porte-fusible connectée à la batterie de la voiture (en

dérivant l’interrupteur d’allumage) (12 V constant)

LINE OUT (FRONT) (see diagram

véase diagrama / voir le diagramme

)

To an accessory terminal in the fuse block

A un terminal accesorio del bloque de fusibles

Vers borne accessoire du porte-fusible

Red / Rojo / Rouge

Blue / Azul / Bleu

Fuse block

Bloque de fusibles

LINE OUT (REAR) (see diagram

Porte-fusible

véase diagrama / voir le diagramme

To automatic antenna if any (250 mA max.)

A la antena automática, si hubiere (250 mA máx.)

À l’antenne automatique s’il y en a une (250 mA max.)

)

SUBWOOFER OUT (see diagram

Blue with white stripe

Azul con rayas blancas

Bleu avec bande blanche

/ véase diagrama / voir le

diagramme

)

To the remote lead of other equipment (200 mA max.)

Al conductor remoto del otro equipo (200 mA máx.)

Au fil de télécommande d’un autre appareil (200 mA max.)

Orange with white stripe

Naranja con rayas blancas

Orange avec bande blanche

To car light control switch

Al interruptor de control de las luces del automóvil

À l’interrupteur d’éclairage de la voiture

Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise power

cannot be turned on.

Antes de comprobar el funcionamiento de esta unidad

previa a de la instalación, es necesario conectar este cable,

de lo contrario no se podrá conectar la alimentación.

To cellular phone system

Al sistema de teléfono celular

Al cellulare

Brown / Marrón / Marron

Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil ne peut

pas être mis sous tension.

To parking brake (see diagram

Al freno de estacionamiento (véase diagrama

Au frein de stationnement (voir le diagramme

)

Light green / Verde claro / Vert clair

)

Gray with black stripe

Gris con rayas negras

Gris avec bande noire

Purple

Púrpura

Violet

White with black stripe

White

Blanco

Blanc

Gray

Gris

Green with black stripe

Green

Verde

Vert

Purple with black stripe

Púrpura con rayas negras

Violet avec bande noire

Blanco con rayas negras

Verde con rayas negras

Blanc avec bande noire

Vert avec bande noire

Left speaker (rear)

Right speaker (rear)

Altavoz derecho (trasero)

Enceinte droit (arrière)

Left speaker (front)

Altavoz izquierdo (frontal)

Enceinte gauche (avant)

Right speaker (front)

Altavoz derecho (frontal)

Enceinte droit (avant)

Altavoz izquierdo (trasero)

Enceinte gauche (arrière)

Connecting the reverse gear signal lead / Conexión del cable de señal del engranaje de marcha atrás / Connexion du fil de signal de marche arrière

Purple with white stripe

Conductor de la luz trasera

Violet avec bande blanche

Reverse lamp lead

Conductor de la luz trasera

Fil des feux de recul

Locate the reverse lamp lead in the

KD-NXD505

REVERSE GEAR SIGNAL

trunk.

Localice el conductor de la luz trasera

en el compartimiento de equipajes.

Localisez le fil des feux de recul dans le

coffre.

To reverse lamp

A la luz trasera

Aux feux de recul

To car battery

A la batería del automóvil

À la batterie de la voiture

Reverse lamp lead

Reverse lamps

Luces traseras

Feux de recul

Conductor de la luz trasera

Fil des feux de recul

Connecting the speed signal lead / Conexión del cable de señal de velocidad /

Connexion du fil de signal de vitesse

*3 Connecting the crimp connector / Conexión del conector de presión / Connexion de la cosse sertie

• This connection is necessary to use the Navigation System.

Esta conexión es necesaria para poder usar el sistema de navegación.

• Cette connexion est nécessaire pour pouvoir utiliser le système de navigation.

•

• If your car does not have a speed signal lead,

use JVC’s Speed Pulse Generator KV-PG1

(separately purchased).

KD-NXD505

SPEED

SINGAL

•

Si su coche no dispone de un conductor de

la señal de velocidad, utilice el Generador de

impulsos de velocidad KV-PG1 de JVC (vendido

separadamente).

Pink/Rosa/Rose

Contact the metallic part of the crimp to the wires inside.

Conecte la parte metálica del engarce a los cables interiores.

Mettez en contact la partie métallique de la cosse à sertir et des fils intérieurs.

Pinch the crimp firmly.

Apriete firmemente el engarce.

Pincez la cosse à sertir fermement.

Signal lead from the speedometer

Conductor del velocímetro

Fil de signal de l’indicateur de vitesse

• Si votre voiture ne possède de pas de fil de signal

de vitesse, utilisez le Générateur d’impulsions

de vitesse KV-PG1 de JVC (vendu séparément).

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the parking brake lead / Conexión del cable del freno de estacionamiento / Connexion du cordon de frein de stationnement

Connect the parking brake lead

to the parking brake system built

in the car.

Conecte el cable del freno de

estacionamiento al sistema de

freno de estacionamiento del

automóvil.

Connectez le fil de frein de

stationnement au système de

frein de stationnement.

Parking brake switch (inside the car)

Interruptor del freno de estacionamiento (dentro del automóvil)

Commutateur de frein de stationnement (intérieur de la voiture)

Parking brake lead of the power cord (light green)

Cable del freno de estacionamiento del cable de

alimentación (verde claro)

Fil du frein de stationnement du cordon

d’alimentation (vert clair)

Parking brake

Freno de estacionamiento

Frein de stationnement

To metallic body or chassis of the car

A un cuerpo metálico o chasis del automóvil

Vers corps métallique ou châssis de la voiture

Connecting to the steering wheel remote controller / Conexión al control remoto del volante de dirección / Connexion de la télécommande de volant

If your car is equipped with the steering wheel remote controller, you can operate this unit using the controller. For

connection, an exclusive remote adapter (not supplied) which matches your car is required. For details, consult the

same car audio dealer as where the unit is purchased.

Si su vehículo está equipado con control remoto en el volante de dirección, podrá hacer funcionar este receptor

utilizando dicho control. Para la conexión, se requiere un adaptador remoto exclusivo (no suministrado) que sea

adecuado para su automóvil. Para los detalles, consulte con el concesionario car audio donde compró el receptor.

Si votre voiture est munie d’une télécommande de volant, vous pouvez commander cet autoradio en utilisant la

télécommande. Pour la connexion, un adaptateur de télécommande exclusif (non fourni) correspondant à votre voiture

est requis. Pour en savoir plus, consultez le revendeur autoradio auprès duquel vous avez acheté cet autoradio.

Remote adapter (not supplied)

OE REMOTE

Steering wheel remote input/ Entrada del

control remoto del volante de dirección/

Entrée de la télécommande de volant

Adaptador para control remoto (no suministrado)

Adaptateur pour télécommande au volant (non fourni)

KD-NXD505

Steering wheel remote controller (equipped in the car)

Control remoto del volante de dirección (equipado en el

vehículo)

Télécommande de volant (installée dans la voiture)

Connecting the external amplifiers / Conexión a los ampliﬁcadores externos / Connexion d’ampliﬁcateurs extérieurs

Vous pouvez connecter des amplificateurs pour améliorer votre système

autoradio.

• Connectez le fil de commande à distance (bleu avec bande blanche) au

fil de commande à distance de l’autre appareil de façon qu’il puisse être

commandé via cet appareil.

• Déconnectez les enceintes de cet appareil et connectez-les à

l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.

• Vous pouvez désactiver l’amplificateur intégré et envoyer les signaux audio

uniquement à un ou plusieurs amplificateurs extérieurs afin d’obtenir un

son clair et pour éviter un échauffement interne de l’appareil. Référez-vous à

la page 95 du MANUEL D’INSTRUCTIONS (volume séparé).

• La voix de guidage sort uniquement par les enceintes avant (et la sortie de

ligne à l’arrière).

You can connect amplifiers to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the

other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, and connect them to the

amplifier. Leave the speaker leads of this unit unused.

• You can switch off the built-in amplifier and send the audio signals only

to the external amplifier(s) to get clear sounds and to prevent internal heat

built-up inside the unit. See page 95 of the INSTRUCTIONS (separate

volume).

Usted podrá conectar amplificadores para mejorar el sistema estéreo de su

automóvil.

•

Conecte el conductor remoto (azul con rayas blancas) al conductor remoto

del otro equipo para poderlo controlar a través de esta unidad.

Desconecte los altavoces de esta unidad y conéctelos al

amplificador. Los cables de los altavoces de esta unidad quedan sin

usar.

•

Podrá desconectar el amplificador incorporado y enviar las señales de audio

solamente al(los) amplificador(es) externo(s) para obtener sonidos nítidos

y evitar que se caliente el interior de la unidad. Véase la página 95 de las

MANUAL DE INSTRUCCIONES (volumen separado).

La guía de voz se escucha sólo a través de los altavoces delanteros (y la salida

de línea delantera en la parte trasera).

• Guidance voice comes out only through the front speakers (and the front

line out on the rear).

Y-connector (not supplied for this unit)

Conector en Y (no suministrado con esta unidad)

Connecteur Y (non fourni avec cet appareil)

Remote lead (Blue with white stripe)

Cable remoto (Azul con rayas blancas)

Fil d’alimentation à distance (Bleu

avec bande blanche)

Remote lead

To the remote lead of other equipment

Al conductor remoto de otro equipo

Au fil de télécommande de l’autre appareil

Cable remoto

Rear speakers

Fil d’alimentation à distance

Altavoces posteriores

Enceintes arrière

LINE OUT (REAR)

JVC Amplifier

Amplificador de JVC

JVC Amplificateur

KD-NXD505

Signal cord (not supplied for this unit)

Cable de señal (no suministrado con esta unidad)

Front speakers

Altavoces delanteros

Cordon de signal (non fourni avec cet appareil)

Enceintes avant

LINE OUT (FRONT)

Firmly attach the ground wire to the metallic body or to the chassis

JVC Amplifier

of the car—to the place not coated with paint (if coated with paint,

remove the paint before attaching the wire). Failure to do so may cause

damage to the unit.

Amplificador de JVC

JVC Amplificateur

Fije firmemente el cable de tierra a la carrocería metálica o al chasis—a

un lugar no cubierto con pintura (si está cubierto con pintura, quítela

antes de fijar el cable). De lo contrario, se podrían producir daños en la

unidad.

Subwoofer

Caisson de grave

SUBWOOFER OUT

Attachez solidement le fil de mise à la masse au châssis métallique de

JVC Amplifier

Amplificador de JVC

JVC Amplificateur

la voiture—à un endroit qui n’est pas recouvert de peinture (s’il est

recouvert de peinture, enlevez d’abord la peinture avant d’attacher le fil).

L’appareil peut être endommagé si cela n’est pas fait correctement.

Connections for external component playback / Conexiones para la reproducción del componente externo / Connexions pour un appareil de lecture extérieur

Video cord (not supplied)

Cordón de video (no suministrado)

Cordon vidéo (non fourni)

VIDEO OUT

VIDEO IN

External monitor

Monitor externo

Moniteur extérieur

KD-NXD505

DIGITAL OUT

KS-U57

See page 106 of the INSTRUCTIONS.

Consulte la página 106 del MANUAL DE

INSTRUCCIONES.

Voir la page 106 du MANUEL

D’INSTRUCTIONS.

(not supplied)

(no suministrado)

(non fourni)

Camcorder, rear view camera, etc.

• Set “External Input” to “Ext Input,” and “Video Input” to “Video”

or “Camera” (see page 93 of the INSTRUCTIONS).

Videocámera, cámera de retrovisión, etc.

Audio/video control amplifier or the decoder compatible

with the multichannel digital sources

Amplificador de control de audio/vídeo o el decodificador

compatibles con las fuentes digitales multicanal

Amplificateur de commande audio/vidéo ou décodeur

compatible avec les sources numériques multicanaux

•

Cambie la configuración de “Entrada externa” a “Entr. ext.” y de

“Entrada de vídeo” a “Vídeo” o “Cámara” (consulte la página 93 de las

MANUAL DE INSTRUCCIONES).

Digital optical cable (not supplied)

Cable óptico digital (no suministrado)

Câble optique numérique (non fourni)

Caméscope, caméra de recul, etc.

• Définir “Entrée ext.” sur “EntréeExt.” et “Entrée Vidéo” sur “Vidéo”

ou “Caméra” (voir la page 93 des MANUEL D’INSTRUCTIONS).

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting other external components / Conexión de otros componentes externos / Connexion d’un autre appareil extérieur

You can connect external components in series as shown in the diagram

Vous pouvez connecter des appareils extérieurs en série comme montré sur

l’illustration ci-dessous.

Los componentes externos se pueden conectar en serie, tal como se muestra

en el diagrama siguiente.

below.

• All the components, adapters or signal cords need to be purchased

separately.

• Tous les composants, adaptateurs ou cordons de signal doivent être achetés

séparément.

•

Todos los componentes, adaptadores o cables de señal se deben comprar

separadamente.

CAUTION:

PRECAUCION:

PRECAUTION:

Before connecting the external components, make sure that the unit is

turned off.

Antes de conectar el cambiador dee componentes externos,

asegúrese de que el receptor esté apagado.

Avant de connecter votre appareil extérieur, assurez-vous que l’autoradio

est hors tension.

•

To use JVC CD changer, Apple iPod or JVC D. player, set “External

Input” to “Changer” (see page 93 of the INSTRUCTIONS).

To use other external components via KS-U57, KS-U58, or

KS-U100K, set “External Input” to “Ext Input” (see page 93 of the

INSTRUCTIONS).

•

Para utilizar un cambiador de CD JVC, Apple iPod o reproductor D. de

JVC, ajuste “Entrada externa” a “Cambiador” (véase la página 93 del

MANUAL DE INSTRUCCIONES).

Para utilizar otros componentes externos a través de KS-U57, KS-U58 o

KS-U100K, ajuste “Entrada externa” a “Entr. ext.” (véase la página 93

del MANUAL DE INSTRUCCIONES).

•

Pour utiliser un changeur de CD JVC, un iPod Apple ou le lecteur D.

de JVC, réglez “Entrée ext.” sur “Changeur” (voir page 93 du MANUEL

D’INSTRUCTION).

Pour utiliser d’autres appareils extérieurs via le KS-U57, KS-U58 ou

KS-U100K, réglez “Entrée ext.” sur “EntréeExt.” (voir page 93 du

MANUEL D’INSTRUCTION).

Apple iPod

KS-BTA200

SIRIUS®

JVC PnP

Apple iPod

KS-PD100

iPod Apple

KS-U100K

KD-NXD505

or / o / ou

JVC D. player

Reproductor D. JVC

Lecteur D. JVC

CD changer jack

Jack para el cambiador de CD

Prise du changeur de CD

SIRIUS®

JVC DLP

DLP JVC

KS-PD500

Processeur DLP JVC

or / o / ou

To disconnect the connector

Para desconectar el cable

External component

Componente exterior

Appareil extérieur

KS-U57

XMDJVC100

Pour déconnecter le connecteur

Hold the connector top tightly (1),

then pull it out (2).

Sujete firmemente la parte superior

del conector (1) y seguidamente,

extráigalo (2).

or / o / ou

External component

Componente exterior

Appareil extérieur

Tenez fermement le connecteur par-

dessus (1) et tirez vers l’extérieur (2).

KS-U58

JVC CD changer

Cambiador de CD de JVC

Changeur de CD JVC

KS-BTA200

JVC DLP

XMDJVC100

KD-NXD505

DLP JVC

Processeur DLP JVC

CD changer jack

Jack para el cambiador de CD

Prise du changeur de CD

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

iPod es una marca comercial de Apple Inc., registrada en los EE.UU. y otros países.

iPod est une marque de commerce d’Apple Inc., enregistrée aux États-Unis et dans les autres pays.

JVC PnP (Plug and Play) / PnP (“Plug and Play”) JVC / PnP (“Plug and Play”)

JVC

XM Satellite radio / radio satelital XM / radio satellite XM

• For listening to the XM Satellite radio, connect XMDirect^TMUniversal Tuner Box (separately purchased) to this

unit using JVC Smart Digital Adapter—XMDJVC100 (not supplied).

•

Para escuchar la radio satelital XM, también puede conectar el Sintonizador universal XMDirect^TM(adquirido por

separado) al receptor mediante un adaptador Smart Digital XMDJVC100 de JVC (no suministrado).

Stereo mini plug

Miniclavija estéreo

Fiche stéré mini

To headphones jack

Al jack para auriculares

À la prise du casque d’écoute

• Pour écouter la radio satellite XM, vous pouvez aussi connecter le tuner universel XMDirect^TM(vendu séparément) à

cet appareil en utilisant l’adaptateur numérique intelligent JVC—XMDJVC100 (non fourni).

KS-U100K

DC power plug

To DC IN jack

To KS-BTA200 or KD-NXD505

A KS-BTA200 o KD-NXD505

Au KS-BTA200 ou KD-NXD505

Clavija de alimentación de CC

Al jack DC IN

To KS-BTA200 or KD-NXD505

Fiche d’alimentation CC

À la prise DC IN

A KS-BTA200 o KD-NXD505

Au KS-BTA200 ou KD-NXD505

XMDJVC100

External component / Componente exterior / Appareil extérieur

Signal cord supplied with your Smart

Digital Adapter

Cable de señal suministrado con el

adaptador Smart Digital

To KS-BTA200, JVC

Cordon de signal fourni avec votre

adaptateur numérique intelligent

Audio signal cord supplied with your

Smart Digital Adapter

*10

DLP, XMDJVC100 or

KS-U57 ^*8

or / o / ou

KD-NXD505

A KS-BTA200, JVC

DLP, XMDJVC100, o

KS-U58 ^*9

Cable de señal de audio suministrado

con el adaptador Smart Digital

KD-NXD505

Au KS-BTA200, JVC

DLP, XMDJVC100 ou

KD-NXD505

Cordon audio fourni avec votre

adaptateur numérique intelligent

3.5 mm stereo mini plug

Miniclavija estéreo de 3,5 mm

Mini-fiche stéréo de 3,5 mm

XMDirect^TMUniversal

Tuner Box

Sintonizador universal

Line Input Adapter KS-U57 (separately purchased)

Adaptador de entrada de línea KS-U57 (adquirido opcionalmente)

XMDirect^TM

Tuner universel XMDirect^TM

Adaptateur pour entrée de ligne KS-U57 (vendu séparément)

Antenna (supplied with XMDirect^TM

Universal Tuner Box)

Aux Input Adapter KS-U58 (separately purchased)

Adaptador de entrada auxiliar KS-U58 (adquirido opcionalmente)

Antena (suministrada con el Sintonizador

Adaptateur pour entrée auxiliaire KS-U58 (vendu séparément)

universal XMDirect^TM

)

Antenne (fournie avec le tuner universel

*10

Signal cord (not supplied)

Cable de señal (no suministrado)

XMDirect^TM

)

Cordon de signal (non fourni)

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Oven IS60C1 User Manual
Invacare Mobility Aid 1110266 User Manual
IOGear Network Card GBU521 User Manual
Jenn Air Cooktop JGC1430 JGC1536 User Manual
Jet Tools Saw M 708955Z User Manual
John Mills Styling Iron John Mills Titanium Hair Straightener User Manual
JVC DVR SR DVM600U User Manual
JVC Home Theater Screen TM A9U User Manual
Kettler Baby Toy 08152 799 User Manual
Konica Minolta GPS Receiver NS NAV02R GPS User Manual