M
Washer-dryer
Instructions for installation and use
WD 10
Download from Www.Somanuals.com. All Manuals Search And Download.
M
Dividing your garments
What goes in your washer-dryer?
Before washing, you can do a great deal to ensure better results. Divide your garments
according to fabric and colour. Read the labels, follow their guidelines.
according to fabric and
colour, is very important
for good results
Before washing.
The labels say it all.
Big and small happily
Divide your washing according Always look at the labels: they together.
This washer-dryer has a special
to the type of fabric and colour tell you everything about your
fastness. garment and how to wash it in
Empty all pockets (coins, paper, the best possible way.
electronic control device for even
distribution: before the spin cycle
starts, this device allows the
money and small obejects) and The table on page 6 shows all
ensure all loose buttons are meanings behind these garments
to
positions
themselves, to minimise noise
and vibrations during the spin
cycle.
repaired or removed prior to symbols. Their recom-
loading.
mendations are important to
achieve better wash results.
Starting the washer-dryer
After installing your new washer-dryer, start a wash cycle
by setting programme "1" at 90 degrees.
Starting your washer-dryer in
the right way is important for the
quality of your wash, to help
prevent future problems and
enhance life expectancy of your
appliance. Once you have
loaded your washer-dryer and
added the detergent together
with any fabric conditioner,
always check that:
1.The door is closed correctly.
2. The plug is secured in the
socket.
3. The water supply is turned
on.
4. Selector knob A is positioned
on one of the symbols (Stop/
Reset).
Choosethedesiredprogramme
The programme is selected
according to the type of garments
thatneedtobewashed.Tochoose
a programme, refer to the table on
page 4. Turn knob A until the
selected programme is aligned
with the mark on the knob, check
that knob B is in the desired
position, ifnecessary use buttons
D, E, F and lastly, press on/off
button G (I position).
For more delicate
garments:
protect underwear, tights
and stockings and delicate
items by placing them in a
canvas pouch
Always disconnect electricity at
the socket and turn off the water
supply.
Remember that, in the event
of a power failure, or should
the washer-dryer switch itself
off, the programme chosen
will remain in its memory.
At the end of the wash cycle...
Lamp H will flash quickly for a
few seconds, then it will begin
flashing more slowly.
Then turn the washer-dryer off
by pressing on-off button G
(O position).You can now open
the washer-dryer door safely.
After having removed the
freshly cleaned washing, leave
the door open to allow air
circulation inside the drum.
How to eliminate the most common stains
Ink and biro Dab with a wad of cotton soaked in methyl alcohol or alcohol at 90°.
Tar Dab with fresh butter, rub in turpentine then wash immediately.
Wax Scrape away, then run a hot iron between two sheets of absorbent paper. Then rub in cotton with turpentine or
methyl alcohol.
Chewing gum Rub in nail polish remover and wipe with a clean rag.
Mold Cotton and white linen should be placed in a solution of 5 parts water, one bleach and a spoon of vinegar, then
washed immediately. For other white fabrics, use hydrogen peroxide at 10 volumes and wash immediately.
Lipstick Dab with ether on wool or cotton. Use tricloroetilene for silk.
Nail polish Place a sheet of absorbent paper on the side of the stain, wet it with nail polish remover, shifting the
garment as the sheet gradually changes colour.
Grass Dab with a wad of cotton soaked in methyl alcohol.
Instructions for installation and use
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding the control panel
Here I’m in command
Making the right choice is important. And it’s easy.
D
F
E
H
I
A
C
B
G
Programme selector knob
Use this knob to select the wash Use this knob to select the
programme. desired drying cycle. Two
Drying cycle knob
Anti-crease
On-off
This button allows you to
interrupt a programme (on
symbol ) keeping the washing
soaking in water before the spin
cycle. It is a very useful button
in particular because it can be
used for delicates and
synthetics. It is only to be used
with wash programmes for
synthetic fabrics, silk and
curtains when it is impossible for
you to take the washing out
immediately.Before opening the
washing machine door, finish the
wash cycle as follows:
Silk and curtains: press button D
and the machine will drain the
water.
Synthetic fabrics: press button D
if you want a spin cycle, or turn
knob A to symbol
the water to be drained.
N.B.:
When button G is pressed, the
washer-dryer is switched on,
when it is not the machine is
switched off.
Turning the appliance off
does not cancel the selected
programme.
Turn this knob clockwise only. options are available:
To select a programme, you
should turn the knob so that the
A - Based on time:
From 40 minutes to 150.
symbol/number of the desired
B - Based on the damp level of
programme is in line with the
the dry clothes:
pointer on the knob.
Iron
:use this slightly damp
Now press on/off button G
(position I), pilot lamp H will start
flashing.
After 5", the setting will be
accepted, pilot lamp H will stop
flashing (staying lit) and the wash
cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset) and wait
5" : when the cancellation has
been accepted, pilot lamp H
flashes, and you can then turn the
appliance off.
setting for clothes that you
intend to iron to reduce effort
and save energy in the drying
cycle.
On-off lamp / door locked
Lamp H flashes slowly when the
appliance is switched on and
awaiting instructions and at the
end of a cycle, indicating that the
door can be opened. It flashes
quickly when the door should
not be opened. A steady light
means the appliance has
Wardrobe
:use this setting
when you want dry clothes that
can be stored after hanging for
a short while.
Extra dry
: use this setting
when you want very dry clothes.
accepted
programme.
the
selected
A cooling stage is foreseen at
the end of the drying cycle.
if you want
Drying cycle lamp
After the wash cycle has been set
and accepted by the washing
machine, turning the knob will
have no effect (except for when
it is on position Stop/Reset).
When this lamp is on, it means
that knob B has been set on a
drying cycle and at the end of the
wash cycle, the appliance will run
the selected tumble drying cycle.
Detergent dispenser
It is divided into three
compartments:
1.Detergent for pre-wash;
2.Detergent for the main cycle
wash;
With “Daily wash”, this function
is not performed.
Slow spin
Use this button to reduce the
spinning speed from 1000 to
500 rpm for the cotton and linen
programmes and from 850 to
500 rpm for the synthetic
fabrics programmes.
3.Fabric conditioner.
Extra Economy
Reduces water consumption
during the rinse cycles. We
recommend that you use this
function only with small laundry
loads, dosing the detergent
proportionally.
3
2
1
The detergent dispenser is here.
3
Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
What are you washing today?
A programme for all seasons
Type of fabric and degree of soil
Programme Detergent
Detergent
Fabric
softener
Length of
the cycle
(minutes)
Description of wash cycle
knob
for prewash for wash
COTTON
Exceptionally soiled whites
(sheets, tablecloths, etc.)
Warm prewash, wash cycle at 90°C, rinse
cycles, intermediate and final spin cycles
165
145
130
95
1
2
3
4
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
Exceptionally soiled whites
(sheets, tablecloths, etc.)
Wash cycle at 90°C, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast colours
Wash cycle at 60°C, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and delicate colours
(shirts, jumpers, etc.)
Wash cycle at 40°C, rinse cycles,
intermediate and final spin cycles
Rinse cycles
Rinse cycles, intermediate and final
spin cycles
Spin cycle
Draining and final spin cycle
Drying cycle for cotton fabrics
Stop/Reset
Interrupts/Cancels the selected programme
SYNTHETICS
Heavily soiled fast colour synthetics (baby
linen, etc.)
Wash cycle at 60°C, rinse cycles,
anti-crease or delicate spin cycle
100
95
5
6
7
8
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
Heavily soiled fast colour synthetics (baby
linen, etc.)
Wash cycle at 50°C, rinse cycles,
anti-crease or delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments)
Wash cycle at 40°C, rinse cycles,
anti-crease or delicate spin cycle
70
Delicate colour synthetics
(all types of slightly soiled garments)
Wash cycle at 30°C, rinse cycles and
delicate spin cycle
30
Rinse cycles
Rinse cycles, anti-crease or delicate
spin cycel
Fabric softener
Rinse cycles with automatic introduction of
softener, anti-crease or delicate spin cycle
Spin cycle
Draining and delicate spin cycle
Drying cycle for synthetic fabrics
Interrupts/Cancels the selected programme
Stop/Reset
DELICATES
Wool
Wash cycle at 40°C, rinse cycles and
delicate spin cycle
60
50
9
◆
◆
◆
Particularly delicate garments and fabrics
(curtains, silk, viscose, etc.)
Wash cycle at 30°C, rinse cycles,
anti-crease or draining
10
◆
◆
Rinse cycles
Spin cycle
Draining
Rinse cyclesi, anti-crease or draining
Draining and delicate spin cycle
Draining
Interrupts/Cancels the selected programme
Stop/Reset
Important: to cancel the wash programme you have just set, select one of the symbols (Stop/Reset) and wait for at least 5 seconds.
The data found in the table is purely indicative, and can vary according to the quantity and type of washing, the water system temperature and
the room temperature.
Special programme
Daily wash Your washer-dryer has a programme available for the washing of lightly soiled garments in a short amount of time.
By setting programme 8 at a temperature of 30°C, you can wash different types of fabrics together (except for wool and silk), with a
maximum load of 3 kg. This programmes allows you to save on both time and energy as it only lasts around 30 minutes.
We recommend the use of liquid detergent.
Instructions for installation and use
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry
A.
Fabric
A combinedWashing and Dry only
Drying Programme
Drying time (Min.)
Load type Max. load
(kg)
Once you have loaded the
type
Look at table A to the side and washing that needs drying (2,5
follow the instructions provided kg max. for cottons, see table
for MAX load to have an for other fabrics ), make sure
automatic washing and drying that:
Extra
dry
Wardrobe Iron
Cotton,
Linen
Clothing of
different
sizes
cycle.
- the door is shut correctly;
2,5
150
145
140
Follow the instructions for wash - the plug is inserted in the socket;
only (see page 2, the paragraph - the water tap is turned on;
entitled "Starting the Washer- - button G has not been pressed
Dryer") and use knob B to set (O position).
the type of drying cycle desired,
Cotton
Terry
towels
2,5
2,5
1
150
100
65
145
90
140
85
Terital,
Cotton
Sheets,
Shirts
then press button G (I position). And now set the wash cycle
knob
If the laundry load to be washed
and dried exceeds the
Set knob A on the appropriate
Acrylics
Nylon
Pyjamas,
socks, etc.
drying setting
depending on
60
60
maximum load foreseen (see
table A), then follow the
instructions provided for wash
only (see page 2, the paragraph
entitled "Starting the Washer-
Dryer").
When the wash cycle has
finished, remove your washing,
divide it up and replace part of it
inside the drum.
the type of fabric, select the type
of drying cycle required using
knob B and then press on-off
button G (I position).
Slips, tights,
stockings,
etc.
1
65
60
60
At the end of the drying cycle...
Wait for lamp H to flash slowly,
then turn the washer-dryer off by
pressing on-off button G
(O position). Now you can open
the appliance door. Once you
have removed the washing from
the appliance, leave the door
open or ajar to avoid the
formation of bad odours and
turn off the water tap.
The data contained in the table are purely indicative.
For cotton loads of less than 1 Kg, use the drying programme
designed for synthetic fabrics.
Now follow the instructions
provided for a dry only cycle.
Repeat this procedure for the
remainder of the load.
IMPORTANT
WARNING
A spin cycle is carried out during the drying if you have set a
cotton programme and a level of dryness (Extra dry
Wardrobe , Iron ).
- During the drying phase, the door tends to get quite hot.
- Do not use the appliance to dry clothes that have been
washed with flammable solvents (e.g. trichlorethylene).
- Do not use the appliance to dry foam rubber or similar
elastomers.
,
- Make sure that the water tap is turned on during the drying
cycles.
- This washer-dryer can only be used to dry clothes which
have been pre-washed in water.
5
Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding labels
Learn the meaning of these symbols and you will get better
results, your garments will last longer resulting in an
improved wash.
All over Europe, garment labels These symbols are divided in
contain messages expressed in five different categories and
small yet important symbols. shapes: washing
, bleaching
Understanding them is very
important if you want to get
better results and treat your
garments the way they deserve
to be treated.
, ironing
and drying
, dry cleaning
.
Useful tips
Turn shirts inside out to get better results
and make them last longer.
Always empty pockets of their contents.
Look at the label: it will always give you useful
advice.
When loading your washing, try to have a mixture
of large to small items.
Make sure you select the right
temperature!
Consult and learn the symbols in this table: they will help you
obtain a better wash, treat your clothes properly, and get a
better performance out of your washer-dryer.
Wash
Bleaching
Ironing
Dry cleaning
Drying
Strong
action
Delicate
action
High
Temp.
Low
Temperat.
A
c
l
Wash at
95°C
Bleaching only in
cold water
Hot iron at max
200°C
Dry clean with any
solvent
Machine dryable
P
Dry clean only with
perchloride, benzine
av., pure alcohol,
R111 and R113
Medium hot
ironing at
max 150°C
Wash at
60°C
Do not machine
dry
Do not bleach
F
Dry clean with av.
benzine, pure alcohol
and R113
Wash at
40°C
Iron at max
110°C
Spread to dry
Hang to dry
without spin
drying
Wash at
30°C
Not ironable
Do not dry clean
Dry on clothes
hanger
Hand wash
Not
washable in
water
Instructions for installation and use
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful tips
Never use your washer-
How much does it weigh?
Holidays: unplug the
appliance.
dryer to wash... torn, fraying or 1 sheet 400-500 gr.
non-hemmed linen. If it is 1 pillow case 150-200 gr.
absolutely neccessary, place it in 1 tablecloth 400-500 gr.
a bag for protection. Do not wash 1 bathrobe 900-1,200 gr.
It is recommended that you
should unplug the machine from
the socket and turn off the water
supply. Leave the door ajar to
allow air circulation to the draw
coloured linen with whites.
1 towel 150-250 gr.
Watch the weight!
Coloured T-shirts, printed and the door gasket area.This will
For best results, do not exceed onesandshirtslastlongerif turned prevent unpleasant odours.
the weight limits stated below inside out before washing.
(figures show weight of dry Printed T-shirts and sweatshirts
garments):
shouldalwaysbeironedinsideout.
- Resistant fabrics:
5 kg maximum
- Synthetic fabrics:
2.5 kg maximum
- Delicate fabrics:
2 kg maximum
Dungaree alert.
WOOLCYCLE
For best results, we
recommend you use a
specific detergent, taking
care not to wash more than
1 kg of laundry.
Very popular “salopette” type
overalls have straps with hooks
that can damage the drum of your
washer-dryer or other garments
during the wash.To minimise the
risk, place hooks in the pocket
and fasten with safety pins.
- Pure new wool:
1 kg maximum
How to wash almost anything
Curtains.
Quilted coats and anorak.
Trainers.
Curtains tend to crease a great You can wash quilted coats and Once you have removed mud
deal. A useful tip to reduce wind-cheaters, too, if they are and dirt from trainers, you can
creasing: fold the curtains and padded with goose or duck even wash them with jeans or
place them in a pillow case or down. Do not load more than any other tough garments. Do
mesh bag. Do not load anything 2-3 kg and never load 5 kg. not wash trainers with whites.
else inside the appliance, this Repeat rinse once or twice
will ensure that the overall using the gentle spin.
weight does not exceed the half
load. Remember to use the
specific programme 10 which
automatically excludes the spin
cycle.
7
Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
It’s important for a good wash
Useful tips about the detergent dispenser
The first secret is the easiest: the detergent dispenser is
opened by pull it outwards.
In compartment 1:
Detergent for pre-washing (powder)
In compartment 2:
Detergent for washing
(powder or liquid)
You must follow the dosage Special containers are sold with
recommendations provided by liquid or powder detergents for
the manufacturers when adding placing inside the washer-dryer
detergent or fabric conditioner. drum, these are positioned
Doses will vary according to the according to the instructions
wash load, the water hardness found in the detergent box
In compartment 3:
Additives (softeners, perfumes, etc.)
3
2
1
and how soiled the washing is.
Never use hand wash
Experience will help you select detergent, because it may form
the right dosage almost too much foam, which could
automatically: it will become your damage the washer-dryer.
secret.
Detergents that are specifically
Ensure no overfilling when formulated for both hand and
adding fabric conditioner in machine wash are an
compartment 3.
exception.
The washer-dryer automatically One last secret: when washing
adds the softener to the wash in with cold water, always reduce
each programme.
the amount of detergent you use:
Liquid detergent is poured into it dissolves less easily in cold
compartment 2 just a few water than in hot water, so part
seconds before starting the of it would be wasted.
wash cycle.
Remember that liquid detergent
is only designed for wash
cycles of up to 60 degrees on
non pre-wash items.
The detergent dispenser can be
removed and cleaned: pull it outwards,
as indicated in the figure. Then leave it
under running water for a few minutes.
A guide to environmentally
friendly and economic use
of your appliance.
Cutting costs efficiently
MAXIMISE THE LOAD SIZE
Achieve the best use of energy, water, detergent and time by using the recommended
maximum load size.
SAVE up to 50% energy by washing a full load instead of 2 half loads.
DO YOU NEED TO PRE-WASH?
For heavily soiled laundry only!
SAVE detergent, time, water and between 5 to 15% energy consumption by NOT
selecting Prewash for slight to normally soiled laundry.
IS A HOT WASH REQUIRED?
Pretreat stains with stain remover or soak dried in stains in water before washing to
reduce the necessity of a hot wash programme.
SAVE up to 50% energy by using a 60°C wash programme.
BEFORE USING A DRYING PROGRAMME ...
SAVE energy and time by selecting the highest suitable spin speed to reduce the water
content in laundry before using a drying programme.
Instructions for installation and use
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before calling, read the following
In most cases, when your washer-dryer fails to work, the problems arising can
be easily solved without having to call for a technician. Before calling for
assistance, always check these points.
But where did all the water go?
The washer-dryer fails to
the door is open or not shut
properly.
Simple: with the new Indesit technology, you need less than
half of it, to get good results on twice as much!
start.
This is why you cannot see the water through the door:
because there is little, very little of it, to respect the
environment yet without renouncing maximum cleanliness.
And, on top of that, you are also saving electricity.
Is the On/Off button
pressed?
If it is, then a programmed start
has been set.
Is the plug correctly inserted
into the socket? It could have
been moved whilst cleaning.
Is there electricity in the
house?
Is the programmed start
knob, in the correct position
A circuit breaker may have
switched off as a result of too
many electrical appliances
working at the same time. Or
maybe due to a general failure
in your entire area.
for
those
models
concerned?
Is the water supply turned
on? For safety reasons, if the
washer-dryer does not load
water, it cannot start a wash
cycle.
Is the washer-dryer door
closed properly?
For safety reasons, the
washer-dryer cannot work if
off, select one of the symbols
stop/reset , then switch it
back on. If the knob continues
to turn, call for assistance
because it is showing an
anomaly.
The washer-dryer fails to
fill with water.
Is the hose correctly
connected to the tap?
Is there a water shortage ?
There could be work in
progress in your building or
street.
RIGHT WRONG
The washer-dryer
continuously fills and
drains water.
Leave the washer-dryer
plugged in while
Turn off the water
supply after use.
This will eliminate
the possibility of
leakage.
cleaning.
Is there sufficient water
pressure? The autoclave
may be malfunctioning.
Even during maintenance,
the appliance should
always be unplugged.
Is the drain hose positioned
too low? It must be installed
at a height ranging from 60 to
100 cm.
Always leave the
Is the tap filter clean? If the
water is very calcareous, or
if work has recently been
carried out on the water
piping, the tap filter could be
clogged with particles and
debris.
Use solvents and
appliance door ajar
to avoid bad odours.
aggressive abrasives.
Never use solvents or
abrasives to clean the
external and rubber parts
of the washer-dryer.
Is the end of the hose
immersed in water?
Clean the
appliance’s
Does the wall drainage
system have a breather
pipe? If the problem persists
even after these checks, turn
the water supply off the
machine and call for
assistance.
If you live on an upper floor of
your building, there may be a
problem with your drain trap.
To solve this problem, a
special valve must be
installed.
exteriors gently.
To clean the
Neglect the detergent
dispenser.
It is removable and can
easily be cleaned by
leaving it under running
water.
exteriors and the
rubber parts of the
appliance, always
use a soft cloth
dipped in warm and
soapy water.
Is the rubber hose kinked?
The tract of the rubber hose
bringing water to washer-
dryer must be as straight as
possible. Make sure it is not
squashed or kinked.
Go on holiday without
thinking about her.
The programme selector
knob keeps turning?
Before leaving, always
make sure that the
washer-dryer is
Wait a few minutes for the
drain pump to empty the
tub, switch the washer-dryer
unplugged and that the
water supply is turned off.
9
Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Is the drain hose kinked?
The tract of the drain hose
must be as straight as
possible. Make sure the drain
hose is not squashed or
kinked.
Is there space between the
machine and adjacent
units? If it is not a built-in
model, the washer-dryer will
oscillate a bit during the spin
cycle. A few cm of space
should therefore be left
around it.
Is the washer-dryer’s drain
duct clogged? Is there an
extension of the drain hose?
If so, is it positioned
incorrectly, blocking the
water flow?
The washer-dryer does
not drain or spin.
Too much foam.
Is the detergent appropriate
for machine washing?Check
whether the definition on its
label reads “for machine wash”
or “hand and machine wash”,
or any other similar wording.
Does
the
selected
programme incorporates
water draining? Some
programmes stop at the end
of the wash cycles and
draining will have to be
selected manually.
The washer-dryer leaks.
Is the correct amount being
used?An excessive amount of
detergent, besides producing
too much foam, does not
guarantee a more effective
wash, and causes scaling in the
internal parts of the appliance.
Is the “Anti-crease"
function -where provided -
enabled? This function
requires manual selection for
draining.
Is the metal ring of the inlet
hose properly attached?
Turn off the water supply,
unplug the appliance and try
tightening its attachment
without forcing it.
Excessive vibration
during the spin cycle.
Is the drain pump clogged?
To check it, turn off the water
supply, unplug the washer-
dryer and follow the
instructions on page 13, or
call for technical assistance.
Have all transit screws been
removed durind instal-
lation? See the following
Is the detergent dispenser The washer-dryer does
obstructed? Remove and not dry.
wash it under tap water.
page
on
installation
procedures.
Check whether:
Is the drain hose well
the plug has been correctly
attached?Turn off the water
inserted into the socket;there
supply, unplug the appliance
is electricity in your home; the
and try tightening its
appliance door has been shut
attachment.
Has the washer-dryer been
levelled correctly? The
levelling of the appliance
Always get
assistance from
authorised
should
be
checked
properly; a delayed start (if
periodically. Adjust the feet
and check them with a level.
available) has not been
selected; programme knob A
has been set to position
(Stop/Reset); the drying cycle
knob B has been set to
position 0.
technicians and
always insist on
original spare parts.
The washer-dryer doesn't
dry properly.
Technical characteristics
Model
WD 10
Check whether:
the end of the drain hose is
underwater; the drain pump is
obstructed; the advice given
on the maximum loads has
been taken; the water tap has
been turned on.
Dimensions
width 59,5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 5 kg for the wash programme; from 1 to 2,5 kg for the drying programme
Electrical
voltage 230/240 Volt 50 Hz
connections
maximum absorbed power 2050 W
If, despite all checks, the washer-
dryer fails to function and the
problem persists, call your
nearest authorised Customer
Service Centre, providing the
following information:
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 46 litre
Spinning speed
up to 1000 rpm
- the nature of malfunction
- the model type no.(Mod.....)
- the serial number (S/N ....)
This information can be found on
the data plate situated at the back
of the washer-dryer.
Control programs
wash: programme 3, temperature 60°C. Carried out with 5 kg load;
in compliance with drying: run with a load of 2.5 kg and knob B set to position
IEC regulation 456
.
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent
modifications
Instructions for installation and use 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and removal
When the new
washer-dryer arrives
Whether new or just transported to a new house,
installation is extremely important for the correct
functioning of your washer-dryer.
After removing the appliance from
its packaging, check that it is
Connection to the water
mains
intact. If in doubt, contact a
Both hot and cold water supplies
qualified technician immediately.
are preferable and they should be
The inside of the machine is
between 34.5kN/m²(5lb/in²) and
supported, fortransportation, by
1034.2kN/m² (150lb/in²) pressure.
four screws on the back panel.
Thehosehavingthe red endfitting
should be encountered between
Electric connection
the hot supply and the threaded
connection adjacent to the letter H
on the rear of the machine. The
hose having the white end fittings
should be connected between the
cold supply and the threaded
connection adjacent to the letter C
on the rear of the machine.
Remember to insert a sealing
washer at each connection to
ensure watertight joints. Do not
overtighten the connections by
using tools -hand tight is sufficient
topreventleaks.Itisgenerallymore
convenient to have these supplies
away from the sink taps. Where
no suitable hot water supply is
available or it does not meet these
requirements, bothinlethosesmay
be connected to a cold supply by
using two taps etc., or a «T»
junction on the plumbing however,
use of cold water only will increase
programmetimes.
Connecting the drain hose
The drain hose (hooked pipe) is
secured to the rear of the machine
by support clips and may be
routed to right or left as required.
Your appliance is now supplied
with a 13 amp fused plug it can
be plugged into a 13 amp socket
for immediate use. Before using
the appliance please read the
instructions below.
Before using the washer-dryer,
remove the screws, remove the
spacers together with the rubber
tubesattachedtothem(keepingall
theparts)andusetheplasticplugs
provided to fill in the holes.
Important:Usethecap(provided)
to close the 3 holes which housed
the stop pin, situated in the right-
hand part of the lower back of the
washer-dryer.
WARNING - THIS APPLIANCE
MUST BE EARTHED.
THE FOLLOWING OPERATIONS
SHOULD BE CARRIED OUT BY A
QUALIFIEDELECTRICIAN.
The hook to be used in case the drain
hose ends at a height below 60 cm.
Replacing the fuse:
When replacing a faulty fuse, a
13 amp ASTA approved fuse to
BS 1362 should always be used,
and the fuse cover re-fitted. If the
fuse cover is lost, the plug must
not be used until a replacement
is obtained.
The drain hose should be placed
in a stand pipe with a minimum
internal diameter of 38 mm (1½
inches)oritcanbepositionedover
a sink or it can be connected as
shown in Fig. A. The height of
stand pipe or sink should be
between 60 and 100 cm (24 and
40 inches). Care must be taken
that the hose is not obstructed,
twisted, submerged or kinked. If
the hose is connected with an
airtightjoining, provisionshouldbe
made to prevent syphoning.
Levelling
The washer-dryer must be
levelled appropriatey in order to
guaranteeitscorrectfunctioning.To
level the appliance, the front feet
must be adjusted; the angle of
inclination, measuredaccordingto
the worktop, must not exceed 2°.
Whenplacedoncarpet, makesure
the ventilation is not reduced.
Note: the maximum temperature
should not exceed 70°C (158°F).
The rubber gasket.
Connect the inlet hose to the
threaded connector on the
machine rear.
The front feet are adjustable.
The guide for draining into tubs and
sinks.
Warning!
The company denies all
liability if and when these
norms are not respected.
Retain the transit screws,
spacers and washers.
Should you move house
then these should be
Plastic bags, expanded
styrofoam, nails and other
packaging parts are not
children’s toys, and are
potentially dangerous.
replaced to support the
inside of the machine to
prevent damage when
transporting the machine.
Water pipe inlet at the top right.
Fig. A
11 Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement fuse covers:
How to connect an alternati-
ve plug:
The wires in this mains lead are
coloured in accordance with the
following code:
If a replacement fuse cover is
fitted, it must be of the correct
colour as indicated by the
coloured marking or the colour
that is embossed in words on the
base of the plug. Replacements
can be obtained directly from
your nearest Service Depot.
BLUE
BROWN
NEUTRAL(N)
LIVE(L)
GREEN&YELLOW EARTH(E)
Disposing of the appliance:
When disposing of the appliance
please remove the plug by
cutting the mains cable as close
as possible to the plug body and
dispose of it as described above.
Removing the plug:
If your appliance has a non-
rewireable moulded plug and you
should wish to re-route the mains
cable through partitions, units
etc., please ensure that either:
the plug is replaced by a fused
13 ampere re-wearable plug
bearing the BSI mark of approval.
or:
the mains cable is wired directly
into a 13 amp cable outlet,
controlled by a switch, (in
compliance with BS 5733) which
is accessible without moving the
appliance.
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
Disposing of the plug:
Ensure that before disposing of
the plug itself, you make the pins
unusable so that it cannot be
accidentally inserted into a
socket.
Instructions for connecting
cable to an alternative plug:
Important: the wires in the
mains lead are coloured in
accordance with the following
code:
Green &Yellow Earth
Blue
Brown
Neutral
Live
As the colours of the wires in the
lead may not correspond with the
coloured markings identifyng the
terminals in your plug, proceed as
follows:
Connect Green & Yellow wire to
terminal marked E or
or
colouredGreenorGreen&Yellow.
Connect Brown wire to terminal
marked L or coloured Red.
Connect Blue wire to terminal
marked N or coloured Black.
If a 13 amp plug (BS 1363) is used
it must be fitted with a
13 amp fuse, either in the plug or
adaptororatthedistributionboard.
If you are in any doubt the
electrical supply to your machine,
consult a qualified electrician
before use.
Instructions for installation and use 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Care and Maintenance
Treat your machine well and it will provide
many years of trouble free service
Your washer-dryer is a reliable companion in life and on the job. It is just as important for you to keep it in
shape.
Your washer-dryer is designed
to provide reliable service over
many years. A few simple steps
will help to prolong its life and
avoid problems. It is advisable,
to turn off water taps when the
machine is not to be used, this
protects the hoses, etc.
It is important to wash
the detergent dispenser
regularly.
To prevent dried washing
powder from
accumulating, place the
dispenser under running
water for a few minutes.
If the water in your area is too
hard, use a deliming product
(water is hard if it often leaves
Never exaggerate with doses.
Normal detergents already
contain deliming agents. Only if
the water is particularly hard,
that is, rich in lime content, do
we recommend the use of a
specific product at every wash.
A periodical wash cycle with a
dose of a deliming product,
without detergents or washing,
may prove useful.
Never use too much detergent
or additives because this could
cause an excess amount of
foam, scaling and possible
damage to the component parts
of your washer-dryer.
whitish stains around taps or
drains, especially of bath tubs.
For more accurate information as
to the type of water in your
system, call the local water
works or a local plumber).
Pockets must always be
emptied removing even pins,
badges and any other hard
object.
The washer-dryer exterior
should be cleaned with a rag
dipped in lukewarm water and
soap.
Do not forget to empty all pockets: small objects can
cause damage to your washer-dryer.
When in need, check the pump and the rubber hose.
The washer-dryer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance.
Small objects may accidentally fall into the pump: coins, hair clips, loose buttons and other small items. To avoid
possible damage, they are withheld in an accessible pre-chamber, situated at the lower end of the pump.
Attention: Before attempting to examine this pre-chamber, first
ensure that the machine has finished its programme and is empty.
Unplug the machine, as with any maintenance.
To gain access gently ease down the top of the plinth panel situated at
the base of the machine, with a screwdriver etc, to release it. Then
ease the top edge forward to allow it to be lifted clear (Fig. 1). Place
a shallow dish or tray below the cover of the pre-chamber to catch
the small amount of water present. Release the cover by turning anti-
clockwise (Fig. 2). Ensure that the cover is securely replaced.
Fig. 1
The water inlet hose
Fig. 2
Re-fit the plinth cover by inserting the hooks on its lower edge into
the slots and ease the top edge back into position.
Check the rubber hose at least once a year. If you see any cracks, replace it immediately. When you use your washer-dryer,
water pressure is very strong and a cracked tube could easily split open.
13 Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Important for the safe use of your washer-dryer
Your safety and that of
Your washer-dryer has been built in compliance
with the strictest international safety regulations.
To protect you and all your family.
your family
Read these instructions and all 7. Never open the detergent 9. While the appliance is
that children do no touch
it. Never force the washer-
dryer door because this
could damage the safety
lock which prevents
accidental opening when the
nachine is working. Allow a
few minutes at the end of the
program for the lock to
release.
the information in this manual
carefully:they are an important
source, not only of numerous
useful tips, but also of vital
information on safety, use and
maintenance.
dispenser while the
appliance is functioning;
do not use hand wash
detergent because the
abundance of foam could
damage its internal parts.
functioning, do not touch
the drain water as it could
reach very high tempera-
tures. The appliance door,
during wash cycles, tends
to become hot; ensure
1. the machine should not be 8. Never pull on the supply
installed in an outdoor
environment, not even
when a roof shelters the
area, because it may be very
dangerous to leave it
exposed to rain and
thunderstorms.
cable or the washer-dryer to
disconnect it from the wall
socket: it is extremely
dangerous.
10. In case of malfunctioning,
first close the water tap
and unplug the appliance
from the wall socket; do
not under any circum-
stances touch internal parts
in order to attempt repairs.
2. It must only be used by
adults and exclusively for
washing clothes following
the instructions provided in
this manual.
I only want an authorised
specialised technician with
original Indesit spare parts!
11. If you interrupt a Wash
Programme before its
end, then the water and
clothes may be hot. The
water level may also be
above the door, see
instruction for draining
the machine before you
open the door and handle
with caution .
3. Should it have to be moved,
proceed with the help of two
or three people and handle
it with the utmost care.
Never try to do this alone,
because the appliance is
very heavy.
12. During theTumble Drying
programme and at its end,
the clothes and drum of
the machine may be hot,
handle with caution and
do not touch the drum.
4. Before loading the washer-
dryer, make sure the drum
is empty.
5. Never touch the washer-
dryer when barefoot or
with wet or damp hands
or feet.
6. Never use extensions or
multiple plugs, which are
particularly dangerous in
humid environments. The
power supply cable must
never
be
bent
or
dangerously compressed.
How to change the power supply cable
The power supply cable must only be replaced by one of our authorised Service Engineers.
Instructions for installation and use 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Stay in touch
THANK YOU for choosing an Indesit appliance. We are confident
you have made a good choice and that your new appliance will give
many years of excellent service.
And we're there when you need us.
Register your purchase
now
This will confirm your entitlement to enter our quarterly prize draw
where you have the possibility to recover the cost of your purchase.
Simply complete and return the Registration Form supplied with the
appliance documents, using the FREEPOST envelope supplied. Or
call the Registration Hotline on 0870 010 4305.
We're as close to you as your telephone
For direct access to Genuine Indesit Spare Parts and Accessories,
call 0870 558 5850 and speak to our skilled staff who can help you to identify and purchase the item you require.
For a Rapid Response to a problem with your appliance, call 0870 607 0805. We're open from Monday to
Saturday (8am - 5.30pm weekdays, 9am - 5pm Saturday). We have our own department of highly trained Indesit
service staff. For most calls, our Service Engineer can fix the problem on the first visit.
Please have the following details to hand when you ring us:
The nature of the problem, the Model Number and the Serial Number.
These numbers can be found on the appliance and on the portion of the Registration Card which you retain.
15 Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for installation and use 16
Download from Www.Somanuals.com. All Manuals Search And Download.
17 Instructions for installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for installation and use 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
Leader for young Europe
Download from Www.Somanuals.com. All Manuals Search And Download.
|