I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Single Stud Short Throw Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PRJ-WALLKIT-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
Visit the InFocus support site at www.infocus.com/support
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
5/32"
(security)
[included]
#2
1/2" (12.7mm)
7/16" (11.2mm)
1/2" (12.7mm)
3/8" (9.5mm)
7/32" (5.6mm)
PARTS
C (1)
[Top cover]
A (1)
D (1)
[Lower cover]
B (1)
[Wall bracket]
[Short throw wall mount]
J (2)
8-32 x 1/2"
(security)
K (2)
1/4-20 x 1/2"
(security)
L (4)
1/4-20 x 3/4"
(security)
F (4)
1/4-20 x 1-3/4"
G (4)
1/4"
H (4)
1/4-20
N (1)
5/32"
(security)
E (1)
[Projector mount]
M (2)
10-24 x 1"
(security)
AA (1)
[Universal interface]
U (2)
#8 x 1/2"
P (4)
5/16 x 2-1/2"
S (4)
10-24 x 3/8"
[not used]
T (2)
5/16-18 x 1/2"
V (2)
#10 x 1"
R (4)
1/4-20 x 3/8"
[not used]
Q (4)
5/16"
Z (2)
5/16"
Y (4)
[Concrete anchor]
X (4)
1/4-20 x 1-1/2"
[not used]
W (4)
10-24 x 1-3/8"
(Including hardware
and instructions)
4
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
Site Requirements
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a
steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific
instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud.
16" or 24" (on center) Studs
Mount Installation Location
(Must be centered on stud)
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the stud(s)
being used to install the mount. Drywall must be
secured to studs with screws 12" on center
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
FRONT
Drywall
**1/2" minimum
Drywall Thickness
(Both Sides of Stud)
**See hazard statement
on page 2!
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
[362, 125 18, C-Shape, S-Stud Section]
Visit the InFocus support site at www.infocus.com/support
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
ASSEMBLY AND INSTALLATION
The single stud short throw wall mount can be mounted to
concrete, concrete block, 2" x 4" wood studs or steel studs.
(Y) x 4
4
Installing Mounting Bracket
(Q) x 4
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before cutting, drilling, or
installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
(P) x 4
5
Mounting Wall Bracket
(B)
Concrete or Concrete Block
1. Determine mounting location on wall.
Figure 2
2. Using wall bracket (B) as a template, mark four holes at the
outer holes in bracket. (See Figure 1)
Wood Studs
1. Determine mounting location on wall. Use a stud finder to
locate studs.
3. Drill four 3/8" x 3-3/8" deep holes at marked locations in wall.
(See Figure 1)
2. Line up inner three holes on wall bracket (B) with center of
stud at desired mounting location. (See Figure 3)
(front view)
3. Using wall bracket (B) as a template, mark three holes at
inner three holes in bracket. (See Figure 3)
(B)
4. Drill three 7/32" x 2-1/2" deep holes at locations marked in
Step 3. (See Figure 3)
(front view)
2
wood stud
x 4
(B)
3
3
x 3
4
Figure 1
4. Install four concrete anchors (Y) into drilled holes. (See
Figure 2)
5. Install four 5/16 x 2-1/2" hex head lag screws (P) through
four 5/16" washers (Q), outer holes of wall bracket (B) and
into concrete anchors (Y). (See Figure 2)
Figure 3
6
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
5. Install three 5/16 x 2-1/2" hex head lag screws (P) through
three 5/16" washers (Q), inner holes of wall bracket (B) and
into drilled holes. (See Figure 4)
5. Hold metal channel on anchor (H) flat alongside plastic
straps and slide channel through hole. (See Figure 6)
Drywall
Plastic Straps
5
(P) x 3
5
(Q) x 3
(H) x 3
Figure 6
6. Holding plastic straps on anchor (H), pull anchor away from
wall until channel rests flush behind wall making sure anchor
channel is positioned vertically on stud. (See Figure 7)
7. Slide plastic cap on anchor (H) towards wall until flange of
cap is flush with wall. (See Figure 7)
(B)
(side view)
Steel Stud
Drywall
Figure 4
Steel Studs
Plastic Cap
IMPORTANT ! : See Site Requirements section before
proceeding with Steel Studs installation to ensure
installation site meets requirements! The drywall must
have a minimum thickness of 1/2"!
6
1. Determine mounting location on wall. Use stud finder to
locate steel studs.
7
(H) x 3
2. Line up inner three holes on wall bracket (B) with center of
stud at desired mounting location. (See Figure 5)
Anchor Metal Channel
Figure 7
3. Using wall bracket (B) as a template, mark three holes at
inner three holes in bracket. (See Figure 5)
4. Drill three 1/2" holes at marked locations in wall. (See
Figure 5)
8. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 8)
9. Repeat Steps 5 through 8 for each mounting hole.
(B)
(side view)
Steel Stud
Drywall
3
8
Plastic Cap
x 3
4
Plastic Straps
Steel stud
Anchor Metal Channel
Figure 5
Figure 8
Visit the InFocus support site at www.infocus.com/support
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
10. Place wall bracket (B) over anchors and align mounting
holes in display mount with holes in anchors. (See Figure 9)
(B)
1
11. Insert 1/4-20 x 1-3/4" Phillips pan head screws (F) through
1/4" washer (G), corresponding mounting hole on wall
bracket and into anchor (H) and tighten until flush against
mount. DO NOT overtighten! (See Figure 9)
Upper plate
1
12. Repeat Steps 10 through 11 for remaining 2 mounting
holes.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of
mounting hardware can damage the steel studs. DO NOT
overtighten mounting hardware!
(side view)
2
Steel Stud
Drywall
(G) x 3
Lower plate
(A)
(F) x 3
11
Figure 10
3. Fasten wall mount assembly (A) to wall bracket (B) using
two 5/16-18 x 1/2" hex head cap screws (T) through two
5/16" washers (Z), the wall bracket and wall mount
assembly. (See Figure 11)
(T) x 2
3
(B)
Anchor Metal Channel
Figure 9
Installation to Wall Bracket
1. Lift wall mount assembly (A) up to wall bracket (B) and hook
upper plate over upper notches on bracket. (See Figure 10)
(A)
2. Slide lower plate into lower notches on bracket. (See
Figure 10)
(B)
(Z) x 2
Figure 11
8
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
Installing Mount Covers
Projector Installation
1. Raise lower cover (D) up to wall mount assembly. (See
Figure 12)
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the short throw projector mounts
up to (and including) the projector does not exceed 25 lbs
(11.34 kg) for the PRJ-WALLKIT-11.
1
Holes for projector mount
(D)
Figure 12
2. Lower top cover (C) onto wall mount assembly. (See
Figure 13)
3. Install two #10 x 1" Phillips pan head tapping screws (V)
through holes on sides of covers. (See Figure 13)
(bottom view)
4. Install two #8 x 1/2" Phillips pan head tapping screws (U)
into top of top cover (C). (See Figure 13)
Figure 14
Projector Mount Installation
1. Line up mounting holes on projector mount (E) with
corresponding holes on mounting plate. (See Figure 14)
(V) x 2
3
2. Install four #10-24 x 1-3/8" Phillips pan machine screws (W)
through projector mount holes and into mounting plate.
(See Figure 15)
(U) x 2
4
IMPORTANT ! : If projector mount is NOT installed in the
same direction as shown, ROLL adjustment screws will
be inaccessible! (See Figure 15)
2
(C)
Mounting plate
Roll adjustment screws
(E)
(W) x 4
2
Figure 13
Figure 15
Visit the InFocus support site at www.infocus.com/support
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
Projector Installation to Mount
Lock
7
6
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO
NOT substitute hardware. Use only the hardware provided by
the manufacturer.
Locking
lever
1. Secure interface bracket (AA) to top of InFocus projector
(not included) using hardware and instructions included with
the interface bracket.
2. Orient projector with attached interface bracket as shown.
(See Figure 16)
6
3. Lift projector so that screws with thumb nuts are aligned
with mounting slots in mount base. (See Figure 16)
4. Slide projector with interface bracket onto mounting slots in
projector mount (F) until screws are seated against the back
of mounting slots. (See Figure 16)
5
Mounting screw
with thumb nut
seated in
mounting slot
4
Thumb nuts
(reverse view)
3
Figure 17
Projector Mount Adjustments
Yaw Adjustment
(E)
1. Loosen yaw adjustment locking screw using a #2 Phillips
screwdriver. (See Figure )
2. Turn Yaw micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
(See Figure )
3. Tighten Yaw adjustment locking screw using a #2 Phillips
screwdriver. (See Figure )
(Interface appearance is example only.
Appearance may vary.)
1
3
Figure 16
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make
certain mounting slots in projector mount slide under thumb
screws and that screws are seated in the back of slots.
5. Verify mounting screws are properly seated in mounting
slots in projector mount. (See Figure 17)
6. Move locking lever to "locked" position. (See Figure 17)
7. Insert key into lock and turn to secure projector to mount.
(See Figure 17)
2
2
Figure 18
10
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
Pitch Adjustment
NOTE: Pitch can be adjusted using the projector mount or the
pitch of the entire arm can be adjusted. See Pitch
Adjustment - Entire Arm section for details.
1. Loosen Pitch adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 19)
2. Turn Pitch micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
(See Figure 19)
2
3. Tighten Pitch adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 19)
1
3
2
1
3
2
Figure 20
Removing Mount Covers
1. Remove two #8 x 1/2" Phillips pan tapping screws (U) and
two #10 x 1" Phillips pan tapping screws (V) to free top cover
(C) and expose pitch adjustment screw. (See Figure 21)
2. Remove lower cover (D) from PRJ-WALLKIT-11. (See
Figure 21)
(V) x 2
1
2
(U) x 2
1
Figure 19
Roll Adjustment
1. Loosen ROLL adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 20)
2. Turn ROLL micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
(See Figure 20)
(C)
3. Tighten ROLL adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 20)
1
(D)
2
Figure 21
Visit the InFocus support site at www.infocus.com/support
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
Pitch Adjustment - Entire Arm
(projector not shown)
1. Loosen two 5/16-18 x 1/2" hex head screws (T) (one on
each side of wall bracket). (See Figure 22)
2. Loosen two bolts (one on each side of pitch adjustment
screw). (See Figure 22)
3. Adjust pitch adjustment screw until mount is at desired pitch
level.
•
•
Turn clockwise to raise mounting level.
Turn counterclockwise to lower mounting level. (See
Figure 22)
1
4. Tighten two bolts (one bolt on either side of pitch adjustment
screw). (See Figure 22)
[Small cable cover]
5. Tighten two 5/16-18 x 1/2" hex head screws (T) (one on
each side of mounting bracket). (See Figure 22)
1
4
2
[Large cable cover]
Lower
Raise
Figure 23
or
3
2. Route projector cable(s) under mount cover and through
short throw projector arm tunnel. (See Figure 24)
(projector not shown)
1
5
(T) x 2
Figure 22
6. Return mount covers to the mount following instructions in
Installing Mount Covers section.
Cable(s)
2
Cable Management (Optional)
NOTE: In most cases, the cable management cover will NOT
need to be removed in order to route cables from
projector to the wall mount. But for some thick cables,
removing the cover may be necessary.
Figure 24
NOTE: Remove mount covers from the mount following
instructions in Removing Mount Covers section.
1. Remove cable management covers (if necessary) from
short throw projector arm. (See Figure 23)
12
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
3. (Optional) Cables can be tied to inside of projector’s front
cover using cable ties (not included). Route cables near
front cover and wrap cable tie through slots on front cover
and around cables. (See Figure 25)
Extension Adjustment
1. Loosen two bolts holding stop bracket in place on underside
of short throw projector mount. (See Figure 27)
2. Adjust mount to desired extension length. (See Figure 27)
3. Tighten two bolts holding stop bracket to secure mount in
desired position. (See Figure 27)
Cable tie (not included)
1
3
2
Route through slots
and around cables
3
Stop bracket
Figure 25
(projector not shown)
4. Replace removed cable management covers (if necessary).
Insert one side of cover into groove and press firmly on the
cover on the other side until it snaps into the other groove.
(See Figure 26)
Figure 27
Security Screw Installation (Optional)
1. Remove two #8 x 1/2" Phillips screws (U) and two #10 x 1"
Phillips screws (V) from top and lower covers. (See Figure 28)
(projector not shown)
2. Install two 8-32 x 1/2" buttonhead security screws (J) and
two 10-24 x 1" buttonhead security screws (M) into top and
lower covers. (See Figure 28)
(V) x 2
1
(U) x 2
1
4
(M) x 2
2
(J) x 2
2
Figure 26
5. Return outer covers to the mount following instructions in
Installing Mount Covers section.
Figure 28
Visit the InFocus support site at www.infocus.com/support
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
3. Remove two bolts holding stop bracket in place on
underside of short throw projector mount. (See Figure 29)
Adapter plate
Stop bracket
x 2
3
x 4 (one at a time)
6
Figure 29
4. Install two 1/4-20 x 1/2" button head security screws (K)
through holes in stop bracket and into holes in sliding nuts.
(See Figure 30)
Figure 31
7. Install one 1/4-20 x 3/4" button head security screw (L) into
hole vacated by removing bolt in Step 6 and into plastic
spacer. (See Figure 32)
Sliding nuts
8. Repeat Steps 6-7 for remaining three bolts one bolt at a
time.
9. It is important to replace adapter plate bolts ONE AT A TIME
or adapter plate could fall from mount during installation!
Adapter plate
Plastic spacer
Stop bracket
(K) x 2
4
Figure 30
5. (Optional) Remove projector from short throw projector
mount according to projector interface instructions.
NOTE: For most projectors, it will be necessary to remove
projector prior to install four security screws to projector
bracket. For ease of installation, it is recommended to
remove projector prior to performing the following
steps.
(L) x 4 (one at a time)
7
Figure 32
10. Reinstall projector to mount. Refer to Projector Installation
6. Remove one of four bolts from adapter plate. (See Figure 31)
section for details.
14
Visit the InFocus support site at www.infocus.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-11
Visit the InFocus support site at www.infocus.com/support
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-11
Installation Instructions
InFocus Corporation
13190 SW 68th Parkway, Ste 200
Portland, OR 97223
8800-002228 Rev00
©2012 InFocus Corporation
09/12
Download from Www.Somanuals.com. All Manuals Search And Download.
|