ASSEMBLY INSTRUCTIONS
OPERATOR'S MANUAL
PARTS LIST
Z
-VAC
Clamshell
Grass Catcher
Kit for NZM
Mid Mount
Riders
Actual product may differ from product pictured above
Models covered:
Includes Clamshell, Blower
and Weight Kits
48” Kit
52” Kit
61” Kit
P/N 7600003
P/N 7600004
P/N 7600005
Manual No. 7011299 (I.R. 03/11/05)
safety rules regarding outdoor power equipment 2
IMPORTANT! READ CAREFULLY THE FOLLOWING SAFETY RULES BEFORE
ASSEMBLING OR OPERATING UNIT.
engine before leaving unit.
TRAINING
-- Never operate with guards not securely in place. Be sure
-- Read, understand, and follow all instructions in the man-
ual and on the unit before starting. If the operator(s) or
mechanic(s) can not read English it is the owner's responsi-
bility to explain this material to them.
all safety features are attached, adjusted properly and func-
tioning properly.
-- Never operate with the hose or cover removed or altered.
-- Do not change the engine governor setting or over speed
the engine.
-- Become familiar with the safe operation of the equipment,
operator controls, and safety signs.
-- Stop on level ground, shut off engine before leaving the
operator's position for any reason.
-- All operators and mechanics should be trained. The
owner is responsible for training the users.
-- Stop equipment and inspect impeller blades after striking
objects or abnormal vibration occurs. Make necessary
repairs before resuming operations.
-- Only allow responsible adults, who are familiar with the
instructions, to operate the unit.
-- Never let children or untrained people operate or service
the equipment. Local regulations may restrict the age of the
operator.
-- Keep hands and feet away intake and discharge areas.
-- Keep pets and bystanders away.
-- Do not operate the unit while under the influence of alco-
hol or drugs.
-- The owner/user can prevent and is responsible for acci-
dents or injuries occurring to themselves, other people or
property.
-- Use caution when crossing roads and sidewalks. Stop
engine if not blowing.
PREPARATION
-- Use care when loading or unloading the machine into a
trailer or truck.
-- Evaluate the terrain to determine what accessories and
attachments are needed to properly and safely perform the
job. Use only accessories and attachments approved by
the manufacturer.
-- Use care when approaching blind corners, shrubs, trees
oSrLotOhePr oEbjeOctPs EthaRt AmaTyIOobNscure vision.
-- Wear appropriate clothing including safety shoes, safety
glasses and ear protection. Long hair, loose clothing or jew-
elry may get tangled in moving parts.
-- Inspect the area where the equipment is to be used and
remove all objects such as rocks, toys and wire, which can
be thrown by the machine.
Slopes are a major factor related to loss-of-control and tip-
over accidents, which can result in severe injury or death.
All slopes require extra caution. If you cannot back up the
slope, or if you feel uneasy on it, do not drive on it.
Do
-- Mow up and down slopes, never across face.
-- Remove obstacles such as rocks, tree limbs, etc.
-- Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Tall grass can hide obstacles.
-- Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction.
Do Not
-- Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
a) Use only an approved container.
b) Never remove fuel cap or add fuel with the engine run-
ning. Allow engine to cool before refueling. Do not smoke.
c) Never refuel or drain the machine indoors.
-- Check that operator's presence controls, safety switches
and shields are attached and functioning properly. Do not -- Do not start or stop on a slope. If tires lose traction, pro-
ceed slowly straight down the slope.
oOpPeraEteRuAnlTesIsOthNey are functioning properly.
-- Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
-- Never run an engine in an enclosed area.
-- Do not use near drop-offs, ditches, or embankments. The
-- Operate only in the daylight or with good artificial light,
operator could lose footing or balance or blower could sud-
keeping away from holes and hidden hazards.
denly turn over if a wheel is over the edge of a cliff or ditch,
-- Be sure of your footing while using pedestrian controlled
or if an edge caves in.
equipment, especially when backing up. Walk, don't run.
-- Do not operate on slopes with wet grass. Reduced foot-
-- Do not operate in reverse unless absolutely necessary.
ing or traction could cause sliding.
Always look down and behind before and while traveling in
-- Do not operate machine on slopes in excess of 10
reverse.
degrees (18% grade) when equipped with a grass catcher.
-- Be aware of the blower discharge direction and do not
-- Do not operate machine without weight kit installed when
point it at anyone. Do not operate the blower without hose
equipped with a grass catcher.
and bagger hood in place.
-- Never leave a running unit unattended. Always stop
3
2 safety rules regarding outdoor power equipment
to cool before storing.
CHILDREN
-- Shut off fuel while storing or transporting. Do not store fuel
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and its activity. Never assume that children will remain
where you last saw them.
near flames or drain indoors.
-- Keep all hardware tight and keep all parts in good work-
ing condition. Replace all worn or damaged decals.
-- Never tamper with safety devices. Check their proper
operation regularly.
-- Keep children out of the mowing area and under the
watchful
care
of
another
responsible
adult.
-- Clean leaves and debris from mufflers and engine to pre-
vent fires. Clean up oil or fuel spillage.
-- Do not allow children or others to ride on the machine,
attachment, or towed equipment (even with the blades off).
-- Be alert and turn unit off if children enter the area.
-- Before and during reverse operation, look behind and
down for small children.
-- Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
-- Never make adjustments or repairs with the engine run-
ning unless specified otherwise.
-- Never allow children to operate the unit.
-- Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
-- Park machine on level ground. Never allow untrained per-
sonnel to service machine.
-- Carefully release pressure from components with stored
energy. (e.g. springs)
EMISSIONS
-- Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth defects,
or other reproductive harm.
-- Only replace impellers. Never straighten or weld them.
-- Keep hands and feet away from moving parts.
-- Frequently check components and replace with manufac-
turer's recommended parts, when necessary.
-- Use only factory authorized replacement parts when mak-
ing repairs.
-- Look for the relevant Emissions Durability Period and Air
Index information on the engine emissions label.
MAINTENANCE AND STORAGE
-- Always comply with factory specifications on all settings
and adjustments.
-- Only authorized service locations should be utilized for
major service and repair requirements.
-- Never attempt to make major repairs on this unit unless
you have been properly trained. Improper service proce-
dures can result in hazardous operation, equipment dam-
age and voiding of manufacturer's warranty.
-- Always observe safe refueling and fuel handling practices
when refueling the unit after transportation or storage.
-- Always follow the engine manual instructions for storage
preparations before storing the unit for both short and long
term periods.
-- Always follow the engine manual instructions for proper
start-up procedures when returning the unit to service.
-- Never store the machine or fuel container inside where
there is an open flame, such as in a water heater. Allow unit
4
unit assembly 3
BLOWER KIT INSTALLATION
REMOVE PULLEY
GUARD
STEP 1: Remove pin, rod and spring securing dis-
charge deflector to mower deck, and remove
deflector. Set rod and pin aside for future assem-
bly step. Store deflector for future use. IMPOR-
TANT: Never operate mower without discharge
deflector or grass catcher securely in place.
REMOVE
DEFLECTOR
STEP 2: Remove two bolts securing right deck pul-
ley guard to mower deck and remove guard. Set
bolts aside for future assembly step. Store guard
for future use. IMPORTANT: Never operate mower
without a pulley guard securely in place.
REMOVE PIN,
ROD AND SPRING
STEP 3: Lift off and set aside foot rest/center deck
cover to expose senter blade deck. Pull blade belt
deck idler arm in direction indicated to relieve belt
tension, and slip blade belt off of right blade drive
pulley.
REMOVE BELT FROM
RIGHT BLADE PULLEY
NOTE: Assistance may be needed for removal of
blade belt.
PULL ON IDLER
TO RELIEVE
BELT TENSION
STEP 4: Remove nut securing pulley to blade
spindle, and install supplied blower pulley on top of
existing pulley. Replace nut, and torque to 70-80 ft-
lbs. Replace deck belt onto groove of bottom pul-
ley.
NOTE: Nut secures blade bolt in place. Support
bolt from beneath while installing pulley.
REPLACE
BELT
IMPORTANT: Use gloves when working under
deck. Sharp blades can cause injury.
ONTO
BOTTOM
PULLEY
BLOWER PULLEY
STEP 5: Set blower against deck discharge. Align
holes in blower mount with holes in deck discharge
tabs, and secure blower with discharge deflector
rod removed in Step 1, securing with pin. NOTE:
Do not reinstall the deflector spring when installing
the rod.
INSTALL BLOWER AND
SECURE WITH ROD AND PIN
FROM UPPER
IDLER PULLEY
STEP 6: Pull back on idler tension release handle,
and install blower belt around top groove of deck
pulley. NOTE: Make sure belt is not rolled or
twisted when installing.
TO LOWER
IDLER PULLEY
PULL
BACK
5
3 unit assembly
STEP 6a: Remove bolts securing impeller pulley
cover to blower, and remove cover.
REMOVE BOLTS,
THEN REMOVE
COVER
STEP 6b: Check to see that blower belt is routed
around impeller pulley and idler pulleys after belt is
installed onto deck pulley. Replace cover, tighten-
ing bolts securely. IMPORTANT: Never operate
any mower without a pulley guard securely in
place.
CHECK TO SEE
THAT BELT IS
ON PULLEYS
STEP 7: Slip tube of locking pin bracket into blow-
er mount, and secure with T-handle pin, making
sure pin goes through both upper and lower holes
in blower mount. Then align base of pin bracket
parallel with rear of deck, and, using bracket as a
template, drill two 7/16” holes through deck. Insert
two 3/8-16 x 1” hex bolts up through deck and
bracket, securing with hex flange lock nuts.
Tighten securely. IMPORTANT: Use gloves when
working under deck. Sharp blades can cause
injury.
DRILL
HOLES &
INSTALL
BOLTS
INSERT
PIN
ALIGN
BRACKET
WITH REAR
OF DECK
STEP 8: Lay supplied pulley guard onto deck,
aligning holes in guard with holes in deck. Install
with bolts securing original guard, tightening
securely.
NOTE: 48” deck shown; 52” and 61” deck guard
configurations may differ.
INSTALL
BOLTS
6
unit assembly 3
STEP 9: Install belt guard between pulley guard
and belt guard support clip on front part of blower
mount. Secure with two 5/16 nylon wing nuts.
Tighten nuts securely.
INSTALL BELT GUARD
AND SECURE WITH
WING NUTS
WEIGHT KIT INSTALLATION
!! Warning: Weight kit must be installed prior to
installing clamshell kit. Failure to do so may
result in longitudal tipping of unit.
STEP 10: Lay weight mount channel, with installed
weights, across front end of machine as shown.
Secure to machine with two clamp plates, one
under each caster arm, each held on with two 3/8-
16 x 4” hex bolts and lock nuts. See Inset. Tighten
securely.
WEIGHT
MOUNT
CHANNEL
CLAMP
PLATE
CLAMSHELL KIT INSTALLATION
STEP 11: Install bumper mount standoffs onto rear
bumper of machine, utilizing existing hardware on
machine. NOTE: Invert hardware when installing
standoffs, installing bolts out through bumper with
nuts facing out.
NOTE: When installing standoffs, be sure that the
bumper mount plate mounting holes along the
back bar of both standoffs are oriented towards the
right side of the machine. Refer to the Parts List
section of the manual.
USE EXISTING
HARDWARE
STEP 12: Install bumper mount plate onto stand-
offs with four 5/16-18 x 3/4 hex bolts, securing with
four 5/16-18 hex flange lock nuts. Tighten secure-
ly.
7
3 unit assembly
STEP 13: Hook bottom of clamshell mount onto
pins in bottom of bumper mount plate, then raise
clamshell assembly up against bumper mount.
RAISE UNIT
IMPORTANT:
Assistance is required when
installing clamshell unit.
HOOK CLAMSHELL
MOUNT ONTO
BUMPER MOUNT
PLATE PINS
STEP 14: Slide hitch rod through aligned holes in
clamshell mount and bumper mount plate, secur-
ing with hair pin.
IMPORTANT:
Assistance is required when
installing clamshell unit.
SECURE
WITH
HAIR PIN
SLIDE ROD
THROUGH
HOLES
STEP 15: Hook the large hole of each actuating
arm onto the hook on each side of the rear cover.
Then secure the other end of the arm onto the
inside of each side of the handle weldment with
one 3/8-16 x 2” hex bolt and nyloc nut. Tighten
snugly. NOTE: Make sure bend of arm is up.
MAKE SURE
BEND IS UP
HOOK
LARGE
HOLE OF
ARM
HERE
BOLT ARM TO
INSIDE OF HANDLE
Push handle down to lock cover.
PUSH HANDLE
DOWN TO
LOCK COVER
8
unit assembly 3
STEP 16: Slip one hose clamp onto each side of
discharge hose, and install hose between blower
and clamshell. NOTE: Install hose so that clamp
with nut is on the clamshell side, and the clamp
with the black quick-release knob is on the blower
side. Tighten both clamps securely.
CLAMP
WITH NUT
CLAMP WITH
BLACK KNOB
unit operation & maintenance 4
If you must back machine to dump clippings in desired
location, LOOK and SEE behind and down for children,
pets and hazards before and while backing.
INTRODUCTION
Follow operation and maintenance instructions in the
Operator’s Manual provided with the Snapper Mid-
Mount Z-Rider.
3. Stop motion of machine by returning Motion Control(s)
to Neutral (N). Set Park Brake. Stop engine.
4. Lift up on handle sufficiently to allow all clippings to exit
catcher. If the dumped pile is too high to allow the catch-
er to close, you may be required to use a rake or simi-
lar implement to distribute the clippings.
5. After dumping, to maintain peak performance, check
the catcher screen located on the inside of the Rear
Cover Assembly to make sure it is clean and free of any
build up. Clean as required with brush or broom.
6. Close catcher. Push down firmly on handle to insure it
is properly latched.
GRASS CATCHER OPERATION
1. Select desired cutting height. Choose a setting that will
not attempt to cut off too much at once, overloading the
machine.
2. After starting engine and allowing a brief warm up peri-
od, move engine speed control to highest setting.
3. Drive machine to cutting area. Engage blades.
4. Select a slow forward ground speed until familiar with
conditions. Do not select a speed that is too fast, caus-
ing the machine to become overloaded.
5. The weight of the grass catcher and contents will affect
the stability and handling of the machine. Avoid sudden
starts and sharp turns. Reduce speed on slopes, and
DO NOT operate machine on slopes exceeding 10
degrees (18% grade). Operate machine up and down
slopes. DO NOT operate machine across the face of
slopes. Turn blades off when traveling up slope.
6. Empty grass catcher often to minimize effect on stabili-
ty and handling. Over filling the catcher will reduce per-
formance and cause clogging of the hose, blower and
deck.
7. Re-start engine and drive machine to cutting area. Set
engine speed to highest setting, engage blades and
resume operation.
WARNING
!
!
DO NOT attempt to remove any clogs from deck, blow-
er, or hose with engine or blade running. STOP engine.
STOP blades. Set brake. Remove key. Make sure
blades and all rotating components have come to a
complete stop before removing any catcher or unclog-
ging any catcher component.
7. Do not operate the machine with the Grass Catcher
open. The entire Grass Catcher must be installed, the
catcher closed and latched properly before operating.
IF THE GRASS CATCHER BECOMES CLOGGED
The grass catcher may become plugged if the conditions
are too severe, the catcher is overfilled, or the machine is
used improperly. If plugging does occur, attempt the follow-
ing:
1. Engine speed too slow – set engine speed control to
“FAST” position.
EMPTYING GRASS CATCHER
1. Empty Grass Catcher often to avoid overfilling.
Overfilling reduces performance and causes clogging of
hose, blower and deck.
2. Turn blades off. Drive machine to location the clippings
are to be dumped. DO NOT operate blades in reverse.
(Continued On Next Page)
9
4 unit operation & maintenance
IF THE GRASS CATCHER BECOMES CLOGGED
(Continued From Previous Page)
To Clear A Plugged Blower
1. Stop blades and blower. Stop engine. Remove key.
2. After all rotating components have come to a complete
stop, loosen the hose clamp at the outlet of the blower.
3. Remove hose from blower.
2. Empty catcher more often.
3. Clean screen on rear cover assembly.
4. Ground speed too fast – cut at slower speed.
5. Removing too much grass – raise cutting height, cut
partial width, and cut lawn more frequently.
4. Using a stick or similar object, clear all obstructions
from blower. DO NOT INSERT HAND.
5. Reinstall hose to blower and securely tighten hose
clamp.
6. Grass is too wet from rain or dew – allow grass to dry.
7. Blades are dull or worn – inspect blades and replace as
necessary. Use only genuine SNAPPER replacement GRASS CATCHER MAINTENANCE
blades.
Grass Catcher components are subject to wear and deteri-
8. Deck, blower, or hose has clipping build up – clean all oration during normal usage. Inspect all components fre-
clippings from all internal surfaces.
quently for signs of wear and deterioration. Replace worn or
damaged components immediately.
WARNING
!
!
BEFORE EACH USE
DO NOT put fingers or hands inside blower! STOP
blades. STOP engine. Remove key. Use only a stick, or
other suitable means, to clear the blower of clogs or
other obstructions!
1. Perform pre-start checklist and maintenance as
instructed in the SNAPPER Mid-Mount Z-Rider
Operator’s Manual and Engine Owner’s Manual includ-
ed with the machine.
2. Clamshell Catcher. Inspect all catcher components.
Replace all worn or damaged parts.
3. Deck, Blower, Hose. Clean grass build up from deck,
blower, hose, covers and rear cover screen. To maintain
peak performance make sure screen is clean at each
dumping.
4. Hose. Check hose for wear, tears and holes. Replace
as needed.
5. Blades. Check blades for sharpness, wear, flatness
and damage. Refer to MMZ Operator’s Manual for
blade wear limits and sharpening/replacement instruc-
tions.
WARNING
!
!
DO NOT attempt any adjustments, maintenance or
repairs with engine running. STOP blades. STOP
engine. Remove key.
WARNING
!
!
Grass Catcher components are subject to deteriora-
tion. Inspect frequently. Replace worn or damaged
components immediately. Use only genuine SNAPPER
replacement parts.
6. Blower. Check blower impeller, blower housing and
inlet/outlets for signs of wear and deterioration. Replace
as needed. Check all fasteners and hardware to insure
none are missing and all are tightened securely.
Lubricate impeller shaft bearings with 1 to 3 shots of
General Purpose grease from a grease gun.
To Clear A Plugged Hose
1. Stop blades. Stop engine. Remove key.
2. After all rotating components (engine, blower, blades)
have come to a complete stop, loosen hose clamp at
outlet of blower, and remove hose from blower.
3. Clear any obstructions from hose. If necessary, use a 7. Belts. Check belts for wear and fraying. Replace as
stick to reach into the hose. needed.
4. Reinstall hose to blower and securely tighten hose 8. Idler Arm. Check idler arm to insure it pivots freely and
clamp.
bushings are not worn. Replace worn bushings as
needed.
10
warranty statement 5
2 YEAR LIMITED WARRANTY
For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any
authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For one (1) year from purchase date for the original purchaser's commercial, non-residential use, SNAPPER, through any
authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the factory at
McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days from purchase date for the original purchaser's rental use, SNAPPER, through any authorized SNAP-
PER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia,
to be defective in material or workmanship or both
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replace-
ment under this warranty must be paid by the purchaser.
This warranty does not apply to certain transmissions, to engines and their components, and batteries, as these items are
warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any
machine or component part that has been altered or modified changing safety, performance, or durability.
Batteries have a one (1) year warranty period with free replacement if required for one (1) year from the original purchase
date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty only covers original equip-
ment batteries and does not cover damage to the battery or machine caused by neglect or abuse, destruction by fire,
explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two (2) years from
purchase date for the original purchaser's residential or other non-commercial use, and one (1) year from purchase for the
original purchaser's commercial, non-residential use, and ninety (90) days from purchase for the original purchaser's rental
use and to the extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities
for consequential damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED
WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the SNAPPER Product Registration Card immediately and mail to:
Snapper's Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253
11
6 unit breakdown & parts list
12
unit breakdown & parts list 6
Snapper Z-Vac Blower Unit Group 48”, 52”, 61” Models
Item
Part No.
Qty
Description
1
3046782
91121
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
7
2
8
4
1
4
2
2
2
9
1
1
1
3
3
WELDMENT, Blower Belt Guard
NUT, 1/2-13 Hex Nyloc
2
3
90183
WASHER, 1/2" Flat SAE
4
3021097
44995
PULLEY, A Groove Idler, Steel
IDLER STUD (3/8-24 thread)
FLAT WASHER, 9/16 Type Narrow
FLANGE BEARING, 9/16" I.D. (powdered metal)
RETAINING RING, 1/2"
BELT RETAINER, Idler
SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5
WELDMENT, Idler Arm
5
6
91804
7
14409
8
10776
9
3046824
91527
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
3047253
91601
NUT, 5/16-18 Hex Flange Lock
SCREW, 1/2-13 x 2-1/2" Hex Head Cap, GR5
WELDMENT, Blower Housing
91218
3046781
3046853
91541
BACK PLATE, Blower
SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap
BEARING, Pillow Block, Blower (includes grease fitting)
NUT, 7/16-14 Hex Center Lock, GR5 or B
SCREW, 7/16-14 x 1-1/2" Hex Head Cap, GR5
IMPELLER, Fast Vac Blower (weldment)
SCREW, 7/16-14 x 1-1/4" Hex Head Cap, GR5
NUT, 3/8-16 Hex Flange Lock
3022832
90839
3031920
3046854
3031919
90613
3046813
3043613
90122
BELT RETAINER
PULLEY, Flat Idler, 2-3/4" O.D.
WASHER, 3/8" Flat SAE
91560
SCREW, 3/8-16 x 2-1/4" Hex Head Cap, GR5
NUT, 3/8-24 Hex Nyloc
91518
91305
SCREW, 3/8-16 x 2" Hex Head Cap, GR5
U-CLIP, 5/16-18
92111
91541
SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap
13
6 unit breakdown & parts list
14
unit breakdown & parts list 6
Snapper Z-Vac Blower Mount Group 48”, 52”, 61” Models
Item
Part No.
Qty
Description
1
3036323
3022844
3037161
33867
1
1
1
1
--
2
1
1
1
1
1
1
1
1
1
1
4
1
2
4
1
1
1
2
1
1
1
1
1
BELT, A Section, 91.125" effective length (used on 48” & 52” Models)
BELT, A Section, 92.0" effective length (used on 61” Models)
WELDMENT, Belt Cover, Deck (used on 48” & 52” Models)
WELDMENT, Belt Cover, Deck (used on 61” Models)
NOT USED
1
2
2
3
-----
4
91537
WING LOCKNUT 5/16-18
5
3037162
3037163
33847
BELT GUARD, 48" Deck
5
BELT GUARD, 52" Deck
5
BELT GUARD, 61" Deck
6
3046806
3046809
3036324
3027505
3027506
33873
PULLEY, Blower Input, 48" & 52"
6
PULLEY, Blower Input, 61"
7
PULLEY, 48"/52" Spindle
8
WELDMENT, 48" Blower Mount
8
WELDMENT, 52" Blower Mount
8
WELDMENT, 61" Blower Mount
9
3027507
91541
WELDMENT, Guard Support Bracket
SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap
WELDMENT, Deck Mount Bracket
SCREW, 3/8-16 x 1" Hex Head Cap, GR5
NUT, 3/8-16 Hex Flange Lock
10
11
12
13
14
15
16
17
18
19
20
--
3027508
91304
90613
3032118
91527
WELDMENT, T-Handle Pin
SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5
NUT, 5/16-18 Hex Flange Lock
NUT, 5/16-18 Hex Large Flange Center Lock
SPRING, Idler, Fast Vac
KEY, 1/4 Square x 1.44
SCREW, 3/8-16 x 6" Hex Head Cap, GR5
BRACKET, Spring (Not Shown; used on 61” Models)
WELDMENT, Spring Bracket (Not Shown; used on 61” Models)
91601
90951
3020807
12315
91617
33740
--
33868
15
6 unit breakdown & parts list
16
unit breakdown & parts list 6
Snapper Z-Vac Clamshell Catcher Group
Item
Part No.
Qty
Description
1
72979
73509
73525
58600
73179
91265
36422
91079
73145
91304
91514
91299
73181
72874
91631
36422
91079
43333
91527
91528
91298
11292
16314
11296
91303
43334
91814
91315
91576
3022833
3022875
3022876
11293
27198
43332
11870
72951
43803
91601
11295
91305
1
COVER, Rear, Clamshell Bagger
SCREEN, Clamshell (Not Shown)
RIVET, 5/32 (Not Shown)
--
1
--
8
2
1
WELDMENT, Rear Cover Brace
HINGE, Rear Cover
3
1
4
5
SCREW, #10-24 x 1-1/2” Hex Washer Machine
WASHER, .190 ID x .75 OD Flat
NUT, 10-24 Hex Flange Lock
BOLT, #10-24 x 1-1/2” Oval Head
SCREW, 3/8-16 x 1" Hex Head Cap, GR5
WASHER, .40 ID x .81 OD Flat
NUT, 3/8-16 Nyloc
5
18
18
13
2
6
7
8
9
4
10
11
--
8
1
COVER, Front, Clamshell Bagger
DEFLECTOR, Clamshell Bagger (Not Shown)
SCREW, #10-24 x 1/2” Hex Head Machine (Not Shown)
WASHER, .190 ID x .75 OD Flat (Not Shown)
NUT, 10-24 Hex Flange Lock (Not Shown)
BRACE, Front Cover Weldment
SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5
WASHER, .375 ID x .875 OD Flat
NUT, 5/16-18 Nyloc
1
--
2
--
2
--
2
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
13
21
16
1
MOUNT, Clamshell
4
WASHER, .33 ID x 1.25 OD Flat
HANDLE BRACE, Clamshell
BOLT, 5/16-18 x 1” Carriage
TUBE ADAPTER WELDMENT
SCREW, 1/4-20 x 1-1/4” Hex Head Cap, GR5
WASHER, 1/4” Split Lock
1
7
1
4
4
4
NUT, 1/4-20 Hex
1
HOSE, Snapper Fast Vac
1
HOSE CLAMP, Upper
1
HOSE CLAMP, Lower
1
BRACKET, Handle Mount
4
BOLT, 3/8-16 x 1” Hex Flange
HANDLE WELDMENT
1
1
GRIP
1
ENDCAP, Tube
2
BRACKET, Hanger
4
NUT, 5/16-18 Hex Flange Lock
ARM, Clamshell Actuating
2
2
SCREW, 3/8-16 x 2" Hex Head Cap, GR5
17
6 unit breakdown & parts list
18
unit breakdown & parts list 6
Snapper Z-Vac Clamshell Catcher Mount Group
Item
Part No.
Qty
Description
1
2
3
4
5
6
50551
2
1
4
4
1
1
STANDOFF, Bumper Mount (weldment)
WELDMENT, Bumper Mount Plate
SCREW, 5/16-18 x 3/4" Hex Head Cap, GR5
NUT, 5/16-18 Hex Flange Lock, GR5
ROD, Hitch
1723436
91318
91601
1717085
15067
HAIR PIN, 3/32 x 1-1/2" Cotter
19
6 unit breakdown & parts list
20
unit breakdown & parts list 6
Snapper Z-Vac Weight Mount Group
Item
Part No.
Qty
Description
1
2
3
4
5
6
7
8
3027501
3046992
91131
1
CHANNEL, Weight Mounting
BAR, Clamp
2
4
4
BOLT, 3/8-16 x 4" Hex Tap, GR5
90546
NUT, 3/8-16 Hex Center Lock, GR5 or B
BAR, Weight
SCREW, 1/2-13 x 4-1/2" Hex Head Cap
NUT, 1/2-13 Hex Flange Lock
PAD, Anti-Skid, Self-Adhesive
3027502
3031021
90619
13
3
3
2
3032142
21
6 unit breakdown & parts list
22
unit breakdown & parts list 6
Snapper Z-Vac Decal Group
Item
Part No.
Qty
Description
1
2
3
4
5
3079231
3046850
3046851
3046883
73956
1
1
1
1
1
DECAL, Z-Vac
DECAL, Danger, Fast-Vac
DECAL, Warning, Fast Vac
DECAL, Warning, Fast-Vac
DECAL, Warning, Billboard (on clamshell unit)
23
ASSEMBLY INSTRUCTIONS
OPERATOR'S MANUAL
PARTS LIST
Z
-VAC
Clamshell
Grass Catcher Kit
for NZM
Mid Mount
Riders
McDonough, GA 30253 U.S.A.
Manual No. 7011299 (I.R. 03/11/05)
|