®
MFG. CO. INC.
Part No. 109-4823 Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
This manual contains assembly, operating, maintenance, adjustment, and safety
instructions for your Exmark OCD01.
BEFORE OPERATING YOUR MOWER,
CAREFULLY READ THIS MANUAL IN ITS ENTIRETY.
By following the operating, maintenance, and safety instructions, you will prolong the
life of your mower, maintain its maximum efficiency, and promote safe operation.
If additional information is needed, or should you require trained mechanic service, contact
your authorized Exmark equipment dealer or distributor.
All Exmark equipment dealers and distributors are kept informed of the latest methods of
servicing and are equipped to provide prompt and efficient service in the field or at their service
stations. They carry ample stock of service parts or can secure them promptly for you from the
factory.
All Exmark parts are thoroughly tested and inspected before leaving the factory; however,
attention is required on your part if you are to obtain the fullest measure of satisfaction and
performance.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. SAFETY
PAGE
1.1 Safety Alert Symbol....................................................................................... 1
1.2 Training ......................................................................................................... 1
1.3 Preparation................................................................................................. 1-2
1.4 Operation ...................................................................................................... 2
1.5 Safety Signs............................................................................................... 2-3
2. SPECIFICATIONS
2.1 Model Number............................................................................................... 3
3. ASSEMBLY INSTRUCTIONS
3.1 Assembly Diagram ........................................................................................ 4
3.2 Installation................................................................................................ 5-13
4. OPERATION
4.1 Opening the Discharge Gate ................................................................... 14-15
4.2 Closing the Discharge Gate.......................................................................... 15
5. ADJUSTMENTS................................................................................................... 16
6. TROUBLESHOOTING ........................................................................................ 16
7. PARTS LIST
7.1 OCD01 Assembly ......................................................................................... 17
7.2 Gate Linkage Assembly................................................................................ 18
7.3 Foot Pedal Assembly.................................................................................... 19
8. WARRANTY ......................................................................................................... 20
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY
1.1 SAFETY ALERT SYMBOL
This SAFETY ALERT SYMBOL
is used both in this manual and on the machine to
identify important safety messages which must be followed to avoid accidents. This
symbol means:
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
The safety alert symbol appears above information which alerts you to unsafe actions or
situations and will be followed by the word DANGER, WARNING, or CAUTION.
DANGER: White lettering / Red background. Indicates an imminently hazardous
situation which, if not avoided, WILL result in death or serious injury.
WARNING: Black lettering / Orange background. Indicates a potentially hazardous
situation which, if not avoided, COULD result in death or serious injury.
CAUTION: Black lettering / Yellow background. Indicates a potentially hazardous
situation which, if not avoided, MAY result in minor or moderate injury.
1.2 TRAINING
1.2.1 Regard the Exmark mower as a piece of power equipment and teach this regard
to all who operate this unit.
1.2.2 Read the instructions carefully. Familiarize yourself with the controls and the
proper use of the equipment. If the operator(s) or mechanic(s) can not read
English, it is the owner’s responsibility to explain this material to them.
1.2.3 Do not allow operation of this machine by untrained personnel. Never allow
children, teenagers, or people unfamiliar with these instructions to use the
mower. Local regulations may restrict the age of the operator.
1.2.4 Avoid mowing while people, especially children, or pets, are nearby. Keep in
mind that the operator or user is responsible for accidents or hazards occurring
to other people or their property.
1.3PREPARATION
1.3.1 Evaluate the terrain to determine what accessories and attachments are needed
to properly and safely perform the job. Only use accessories and attachments
approved by Exmark.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.2 The use of personal protective equipment, such as (but not limited to) protection
for the eyes, ears, feet, and head is recommended.
CAUTION
POTENTIAL HAZARD
♦ The mower that the OCD01 attaches to
produces sound levels in excess of 85
dBA at the operator’s ear when in
operation.
WHAT CAN HAPPEN
♦ Exposure to sound levels of 85 dBA or
above for extended periods of time can
cause hearing loss.
HOW TO AVOID THE HAZARD
♦ Wear hearing protection when operating
this machine.
1.3.3 While mowing, always wear substantial footwear and long trousers. Do not
operate equipment when barefoot or when wearing open sandals.
1.3.4 Thoroughly inspect the area where the equipment is to be used and remove all
stones, sticks, wires, bones, and other foreign objects which may damage the
equipment or cause personal injury to the operator or bystanders.
1.4 OPERATION
Although hazard control and accident prevention are partially dependent upon the
design and configuration of the equipment, these factors are also dependent
upon the awareness, concern, prudence, and proper training of the personnel
involved in the operation, transport, maintenance, and storage of the equipment.
It is essential that all Operator Safety Mechanisms be connected and in operating
condition prior to use for mowing.
1.4.1 Give complete, undivided attention to the job at hand.
1.4.2 Mow only in daylight or good artificial light, keeping away from holes and hidden
hazards. NEVER carry passengers.
DO NOT operate the mower when children or others are in the area.
1.4.3 When feasible, avoid operating the equipment in wet grass.
1.5 SAFETY SIGNS
1.5.1 Keep all safety signs legible. Remove all grease, dirt and debris from safety
signs and instructional labels.
1.5.2 Safety signs must be replaced if they are missing or illegible.
1.5.3 When new components are installed, be sure that current safety signs are
affixed to the replaced components.
1.5.4 New safety signs may be obtained from your authorized Exmark equipment
dealer or distributor or from Exmark Mfg. Co. Inc.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5.5 Safety signs may be affixed by peeling off the backing to expose the adhesive
surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.
1.5.6 Familiarize yourself with the following safety signs and instruction labels. They
are critical to the safe operation of your Exmark commercial mower.
PART NO. 98-5954
PART NO. 1-403005
LOCATION: On the Side of the
LOCATION: On Top of the Gate
Gate Linkage
Linkage Assembly
Assembly
PART NO. 109-3595
LOCATION: On Top of the Cable
Bracket Assembly
2. SPECIFICATIONS
2.1 MODEL NUMBER: OCD01
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ASSEMBLY INSTRUCTIONS
IMPORTANT: Disengage blade, shut off engine, wait for all moving parts to stop,
engage parking brake, remove key, and disconnect the wire from the spark plug
before servicing, cleaning, or making any adjustments to the unit.
3.1 ASSEMBLY DIAGRAM
Item Part No.
Description
Qty.
Item Part No.
Description
Qty.
1
2
3
109-3880
3296-29
3230-9
Asm, Cable Bracket w/Decal ................... 1
Nut, Nyloc 5/16-18................................... 4
Bolt, Carriage 5/16-18 x 2 3/4 (Triton)...... 1
Bolt, Carriage 5/16-18 x 2 3/4 (UltraCut).. 2
Screw, HH 5/16-18 x 3/4.......................... 2
Pedal, Foot .............................................. 1
Washer, 5/16 Std (Triton)......................... 3
Washer, 5/16 Std (UltraCut)..................... 7
Nut, Whizlock 5/16-18.............................. 3
12 109-3603
13 3230-2
3230-2
Asm, Gate Linkage w/Decals................... 1
Bolt, Carriage 5/16-18 x 1 (Triton)............ 3
Bolt, Carriage 5/16-18 x 1 (UltraCut) ........ 2
Pin, Hair................................................... 1
Washer, 5/16 SAE (Triton)....................... 2
Washer, 5/16 SAE (UltraCut)................... 1
Asm, Gate................................................ 1
3230-9
14 1-806003
15 3256-23
3256-23
4
5
6
322-3
109-3884
3256-3
16 109-3605
3256-3
17 109-4089-01 Plate, Blocker (Triton) .............................. 1
18 3230-1 Bolt, Carriage 5/16-18 x 3/4 ..................... 1
19 109-3881-01 Bracket, Chute Pivot (UltraCut)................ 1
7
8
32128-20
109-3606„ Asm, Cable 60”-72”.................................. 1
109-3882ꢀ Asm, Cable 46”-56”.................................. 1
20 322-6
Screw, HH 5/16-18 x 1 1/4 (UltraCut)....... 1
Kit, Flexible Discharge Chute (Ultra Cut).. 1
Screw, HWH 5/16 x 1/2 TF ...................... 2
9
109-4101
Strap, Cable Hanger ................................ 1
21ꢁ 109-3860
22 9266934
10 109-4097-01 Cover, Gate Linkage................................ 1
11 9266714 Screw, HWH 1/4-20 x .50 TF (UltraCut)... 3
Used for Triton (series 5) decks 60”, 66”, & 72” (long cable).
„
ꢀ
ꢁ
Used for Triton (series 5) decks 46”, 50”, & 56” and UltraCut (series 4) decks 52” & 60” (short cable).
For serial numbers 669,999 and lower. Not included – needs to be purchased separately.
FIGURE 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 INSTALLING OCD01 TO THE MOWER DECK
3.2.1 Remove discharge chute from deck.
For UltraCut Decks: Remove and discard discharge chute and hardware. Decks with
serial numbers 669,999 and lower require a flexible discharge chute, kit # 109-3860.
The kit is not supplied with the OCD01 accessory and needs to be purchased
separately.
For Triton Decks: Remove and retain the discharge chute and hardware.
3.2.2 Use Figure 2 to locate the correct mounting holes on the pedal pivot bracket.
FIGURE 2
3.2.3 Install the foot pedal on the pedal pivot bracket. The upper screw, 5/16-18 x 3/4 (item 4)
installs from the bottom of the pedal pivot bracket as shown in Figure 3. Fasten with
whizlock nut (item 7).
FIGURE 3
3.2.4 The lower screw installs from the top down as shown in Figure 4. Fasten with whizlock
nut (item 7).
FIGURE 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.5 Install the cable bracket (item 1) by the foot pedal and leave the hardware loose. Use
the correct mounting holes as shown in Figure 5A.
FIGURE 5A
FIGURE 5B
3.2.6 Install cable. Make sure the nuts are centered as shown in Figure 6.
FIGURE 6
3.2.7 Remove the belt cover near the discharge opening.
3.2.8 Route the cable over the left side of the cross-shaft. Remove the seal and run the nuts
off the cable. Feed the parts loosely through one hole of the cable hanger strap. Hang
the cable under the right side of the cross-shaft and fasten with cable hanger strap as
shown in Figure 7. Reinstall nuts and seal.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 7
3.2.9 If there are protruding welds on the discharge opening, grind them flush.
NOTE: Any welds left protruding from the face of the discharge opening could
interfere with free operation of the discharge gate.
For Triton decks only: Install the blocker plate (item 17) as shown in Figure 8.
FIGURE 8
3.2.10 For Triton (series 5) decks 46”, 50”, & 56” and UltraCut (series 4) decks
52” & 60”, cut the discharge gate as shown in Figure 9.
FIGURE 9
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.11 Hook the gate assembly (item16) to the gate linkage assembly (item 12). Install the
washer (item15) and fasten with the hairpin (item 14) as shown in Figure 10.
FIGURE 10
3.2.12 Mount the gate linkage assembly to the deck.
NOTE: The gate is easier to retain on the link assembly if rotated to the “open” position
when installing on the deck.
For UltraCut deck:
a) Install three 1/4-20 self-tapping screws (item 11) into the chute pivot bracket
(item 19) as shown in Figure 11A.
FIGURE 11A
b) Locate the correct mounting hole as shown in Figure 11B. Drill holes in deck as
shown in Figure 11C. Install the two 5/16-18 x 1 bolts (item 13) and fasten to the
deck with washer (item 6) and nyloc nut (item 2). Install 5/16-18 x 3/4 bolt
(item 18) from the bottom of the deck, and draw up into hole using the whizlock
nut (item 7).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 11B
FIGURE 11C
For 46”-60” Triton decks:
a) Locate the correct mounting hole as shown in Figure 11D. Install two 5/16-18 x
1 bolts (item 13) and fasten to the deck with washer (item 6) and nyloc nut
(item 2). Install 5/16-18 x 3/4 bolt (item 18) from the bottom of the deck, and
draw up into hole using the whizlock nut (item 7), see Figure 11E for correct
mounting hole location.
FIGURE 11D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 11E
For 66” & 72” Triton decks:
a) Install two 5/16-18 x 1 bolts (item 13) and fasten to the deck with washer (item 6)
and nyloc nut (item 2) as shown in Figure 11E. Drill Ø.375 hole in the deck to
mate up with the gate linkage assembly (item 12) where shown in Figure 11F.
The drilled hole location will avoid under deck baffles on the deck. Install 5/16-
18 x 3/4 bolt (item 18) from the bottom of the deck, and draw up into hole using
the whizlock nut (item 7).
FIGURE 11F
3.2.13 With foot pedal in unlocked position (see Figure 12), attach the cable onto the blocker
pivot plate assembly. Attach cable and adjust mounting nuts to the center of the
threaded portion of the cable as shown in Figure 13.
FIGURE 12
FIGURE 13
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.14 Slide the bracket that is shown in Figure 6, back and forth to adjust the cable tension.
Take up the slack in the cable, but it should not be taut. Tighten hardware to retain the
bracket.
3.2.15 When pushing on the spring, there should be a 1/16” gap between the spring and the
blocker pivot plate assembly. Fine adjustments can be made by adjusting the cable
mounting nuts as shown in Figure 13. Press the foot pedal in the forward lock position,
the spring should stretch slightly when it locks over center.
FIGURE 14
3.2.16 Install the gate linkage cover to the gate linkage assembly as shown in Figure 15.
FIGURE 15
3.2.17 To make sure the OCD01 assembly is installed correctly:
a) Place the foot pedal in the locked position. Gate should be raised to nearly
horizontal position.
b) Place foot pedal in the unlocked position. Gate should move to vertical position,
closing off the discharge opening. If you try to open the gate with your hands,
the gate should be locked into place. If the gate opens, the cable is tensioned
too tightly. Readjust the bracket and nut as stated in 3.2.14.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.18 Remove the discharge chute bracket from the discharge chute and retain hardware.
Use the appropriate template provided as a guide to cut off the lip. Follow steps a)
through d).
For UltraCut 52”-60” use template 109-4091.
For Triton 46”-56” use template 109-4091.
For Trition 60”-72” use template 109-3592.
a) Place the template onto the chute lip.
FIGURE 16A
b) Cut ends as shown on template. Cut around backside of first rib as shown in
Figure 16B
G0972
FIGURE 16B
12
Download from Www.Somanuals.com. All Manuals Search And Download.
c) Remove remaining lip as shown in Figure 16C.
G0945
G0938
FIGURE 16C
CHUTE WITH LIP
FIGURE 16D
CHUTE WITH LIP REMOVED
d) Using the existing hardware, reinstall the discharge chute bracket into the flexible
discharge chute as shown in Figure 17.
For UltraCut Only: Install 5/16-18 x 1-1/4 screw (item 20) and 3 or 4 washers
(item 6) in the center hole of the bracket as shown in Figure 17, so that the edge
of the chute will be parallel with the deck in the down position.
FIGURE 17
e) When installation is completed, rotate gate assembly (item 16) through its full
travel range and check clearance with discharge chute. Trim additional material
from discharge chute if necessary.
3.2.19 Reinstall the belt cover.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. OPERATION
IMPORTANT: Always mow with the flexible discharge chute installed and in the down position.
DANGER
POTENTIAL HAZARD
♦ An uncovered discharge opening will
allow objects to be thrown in an
operator’s or bystander’s direction. Also,
contact with the blade could occur.
WHAT CAN HAPPEN
♦ Thrown objects or blade contact can
cause serious injury or death.
HOW TO AVOID THE HAZARD
♦ Never operate the mower with the
discharge deflector raised, removed, or
altered unless there is a grass collection
system or mulch kit in place and working
properly.
DANGER
POTENTIAL HAZARD
♦ The rotating blades under the mower
deck are dangerous.
WHAT CAN HAPPEN
♦ Blade contact can cause serious injury or
kill you.
HOW TO AVOID THE HAZARD
♦ DO NOT put hands or feet under the
mower or mower deck when the blades
are engaged.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 OPENING THE DISCHARGE GATE
4.1.1 Press the pedal into the forward lock position and the discharge gate will be open.
FIGURE 18
4.2 CLOSING THE DISCHARGE GATE
4.2.1 Depress the lower tab to unlock the pedal. Then the discharge gate will then close off
the discharge opening.
FIGURE 19
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. ADJUSTMENTS
IMPORTANT: Disengage blade, shut off engine, wait for all moving parts to stop, engage
parking brake, remove key, and disconnect the wire from the spark plug before servicing,
cleaning, or making any adjustments to the unit.
5.1.
Refer back to installation instructions.
6.TROUBLESHOOTING
6.1 GATE DOES NOT LOCK WHEN CLOSED
If you try to open the gate with your hands, the gate should be locked into place. If the
gate opens, the cable is tensioned too tightly. Fine tune the mounting nuts on the cable by
following steps 3.2.13 through 3.2.15.
6.2 GATE DOES NOT OPEN
If the gate does not open when the foot pedal is in the locked position, the cable is not
tensioned properly. Adjust the bracket and mounting nuts in step 3.2.13 through 3.2.15.
6.3 GATE DOES NOT ROTATE FREELY AND STICKS IN THE UP POSITION
Check the discharge opening on the deck for protruding welds. Any welds left protruding
from the face of the discharge opening could interfere with free operation of the discharge
gate. Remove the discharge chute and gate linkage assembly from the deck and grind
welds flush as shown in Figure 8. Reinstall gate linkage assembly and discharge chute.
6.4 GATE INTERFERES WITH THE DISCHARGE CHUTE
When installation is completed, rotate gate assembly through its full travel range and
check clearance with discharge chute. Trim additional material from discharge chute if
necessary.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. PARTS LIST
7.1 OCD01 ASSEMBLY
Item Part No.
Description
Qty.
Item Part No.
Description
Qty.
1
2
109-3603
109-3605
109-3880
Asm, Gate Linkage W/Decals...............1
Asm, Gate............................................1
Asm, Cable Bracket W/Decal ...............1
13
3256-23
3256-23
3256-3
Washer, 5/16 SAE (Ultra Cut) .............. 1
Washer, 5/16 SAE (Triton)................... 2
Washer, 5/16 Std (UltraCut)................. 7
Washer, 5/16 Std (Triton)..................... 3
Nut, Nyloc 5/16-18 (Triton) ................... 4
Nut, Whizlock 5/16-18.......................... 3
Screw, HWH 1/4-20 x .50 (Ultra Cut).... 6
Pin, Hair............................................... 1
Asm, Cable 60” –72” ............................ 1
Asm, Cable 46”–56” ............................. 1
Template, Small Chute Cut Pattern...... 1
Template, Large Chute Cut Pattern...... 1
Screw, HH 5/16-18 x 1 1/4 (UltraCut) ... 1
Decal, OCD01 Operation...................... 1
3
14
4
109-3881-01 Bracket, Chute Pivot (Ultra Cut) ...........1
109-3884 Pedal, Foot...........................................1
3256-3
5
15
16
3296-29
32128-20
9266714
1-806003
109-3606
109-3882
109-4091
109-3592
322-6
6
109-4089-01 Plate, Blocker (Triton)...........................1
109-4097-01 Cover, Linkage .....................................1
7
17
8
109-4101
322-3
Strap, Cable Hanger.............................1
Screw, HH 5/16-18 x 3/4.......................2
Bolt, Carriage 5/16-18 x 3/4..................1
Bolt, Carriage 5/16-18 x 1 (Ultra Cut)....2
Bolt, Carriage 5/16-18 x 1 (Triton).........3
Bolt, Carriage 5/16-18 x 2 3/4 (Ultra Cut) .2
Bolt, Carriage 5/16-18 x 2 3/4 (Triton)...1
18
9
19ꢀ
V
10
11
3230-1
3230-2
3230-2
3230-9
3230-9
20„
12
21„
22
109-3595
ꢀ
Used for Triton (series 5) decks 60”, 66”, & 72” (long cable)
V
Used for Triton (series 5) decks 46”, 50”, & 56” and Ultra Cut (series 4) decks 52” & 60” (short cable)
Not shown.
Q
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 COMPONENTS FOR 109-3603 ASSEMBLY
Item Part No.
Description
Qty.
Item Part No.
Description
Qty.
1
2
3
4
5
1-403005
98-5954
Decal, Danger ......................................1
Decal, Danger ......................................1
Link, Gate ............................................1
Spring, Extension .................................1
6
7
109-4096
3256-23
3272-5
Wld, Gate Crank .................................. 1
Washer, 5/16 SAE ............................... 1
Pin, Cotter 3/32 x 1/2 ........................... 1
Screw, HWH 1/4-20 x .50..................... 2
Screw, HWH 5/16 x 1/2 TF .................. 2
109-3600
109-3604
8
9
9266714
9266934
109-4093-01 Bracket, Link Pivot................................1
10
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3 COMPONENTS FOR 109-3884 ASSEMBLY
Item Part No.
Description
Qty.
Item Part No.
Description
Rod, Pedal Pivot .................................. 2
109-3879-01 Latch, Gate Pedal ................................ 1
Qty.
1
2
3
4
109-3608-01 Bracket, Pedal Pivot.............................1
109-3609-01 Pedal, Gate ..........................................1
5
6
7
8
109-3878
109-3610
Rod, Pedal Link ...................................1
3256-23
Washer, 5/16 SAE ............................... 1
Pushnut, Washer Cap.......................... 6
109-3877-01 Channel, Pedal Link .............................1
32112-11
19
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
2-Year Limited Warranty
Exmark Turf Equipment
(For units purchased on or after October 1, 2004)
Conditions and Products Covered
Owner’s Responsibilities
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty
Company, pursuant to an agreement between them, jointly
warrant on the terms and conditions herein, that we will repair,
replace or adjust any part manufactured by Exmark and found
by us (in the exercise of our reasonable discretion) to be
defective in factory materials or workmanship for a period of
two years.
The Exmark turf equipment, including any defective part,
must be returned to an authorized Exmark service dealer
within the warranty period. This warranty extends only to
turf equipment operated under normal conditions. You
must properly service and maintain your Exmark product
as described in the operator’s manual. Such routine
maintenance, whether performed by a dealer or by you, is
at your expense.
This warranty applies to Exmark turf equipment purchased on
or after October 1, 2004 sold in the US or Canada. This
warranty may only be assigned or transferred to a second (or
third) owner by an authorized Exmark dealer. The warranty
period commences upon the date of the original retail
purchase.
As a condition to this warranty, customer shall have read
the operator's manual and shall have completed and
submitted to Exmark Warranty Company, within the
prescribed time, the Exmark warranty registration.
General Conditions
Products
Warranty Period
2 years
The sole liability of Exmark and Exmark Warranty Company
with respect to this warranty shall be repair and replacement
as set forth herein. Neither Exmark nor Exmark Warranty
Company shall have any liability for any other cost, loss
or damage, including but not limited to, any incidental
or consequential loss or damage.
• All Products (except as noted below)
• All Attachments and Accessories
• Metro 21 and Metro 26 Series
• Belts and Tires
1 year
1 year
90 days
• Battery
• Engine*
1 Year Prorated
In particular, we shall have no liability or responsibility for:
Warranty is covered by engine manufacturer
•
•
Expenses related to gasoline, oil or lubricants.
Travel time, overtime, after hours time or other
extraordinary repair charges or charge relating to
repairs or replacements outside of normal business
hours at the place of business of the authorized
Exmark service dealer.
*Please refer to the engine manufacturer’s warranty statement
that is included in the literature packet. We are not authorized
to handle warranty adjustments on engines.
This warranty only includes the cost of parts and labor.
•
Rental of like or similar replacement equipment
during the period of any warranty, repair or
replacement work.
Any telephone or telegram charges or travel charges.
Loss or damage to person or property other than that
covered by the terms of this warranty.
Any claims for lost revenue, lost profit or additional
cost as a result of a claim of breach of warranty.
Attorney's fees.
Items and Conditions Not Covered
This warranty does not cover the following:
•
•
•
•
Pickup and delivery charges to and from any authorized
Exmark Service Dealer.
Any damage or deterioration due to normal use, wear
and tear, or exposure.
Cost of regular maintenance service or parts, such as
filters, fuel, lubricants, tune-up parts, and adjustments.
Any product or part which has been altered or misused
or required replacement or repair due to normal wear,
accidents, or lack of proper maintenance.
Any repairs necessary due to use of parts, accessories
or supplies, including gasoline, oil or lubricants,
incompatible with the turf equipment or other than as
recommended in the operator's manual or other
operational instructions provided by Exmark.
•
•
•
•
No Claim of breach of warranty shall be cause for
cancellation or rescission of the contract of sale of any
Exmark mower.
•
There are no understandings, agreements, representations,
or warranties, express or implied, including but not limited to
any regarding the merchantability (that product is fit for
ordinary use) or fitness for use (that product is fit for a
particular purpose), not specified herein, respecting the
equipment which is the subject of this warranty.
All warranty work must be performed by an authorized Exmark
Service Dealer using Exmark approved replacement parts.
Instructions for Obtaining Warranty Service
1. Contact any Exmark Service Dealer to arrange service at
their dealership. To locate a dealer convenient to you,
may also call 402-223-6375.
Some states do not allow exclusions of incidental or
consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions and
limitations may not apply to you.
2. Bring the product and your proof of purchase (sales
receipt) to the Exmark Service Dealer.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
If for any reason you are dissatisfied with the Service Dealer’s
analysis or with the assistance provided, contact us at:
Exmark Customer Service Department
The Exmark Warranty Company
2101 Ashland Avenue
Beatrice, NE 68310
402-223-6375 or
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE RECORD
Date
Description of Work Done
Service Done By
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SEE EXMARK’S COMPLETE
LINE OF ACCESSORIES
RIDING ACCESSORIES
CUSTOM RIDE SEAT SUSPENSION SYSTEM
DECK LIFT ASSIST KIT
HITCH KIT
LIGHT KIT
MICRO-MULCH SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)
SNOW BLADE
SUN SHADE
TRASH CONTAINER
TURF STRIPER
ULTRA VAC COLLECTION SYSTEM
ULTRA VAC QUICK DISPOSAL SYSTEM
WALK BEHIND ACCESSORIES
GRASS CATCHER
MICRO-MULCH SYSTEM
STEERABLE SULKY
SULKY HITCH KIT
TURF STRIPER
STANDON
Check us out on the Web:
© 2006
EXMARK MFG. CO. INC.
PART NO. 109-4823 Rev B.
INDUSTRIAL PARK BOX 808
BEATRICE, NE 68310
(402) 223-6300
FAX (402) 223-5489
®
MFG. CO. INC.
ALL RIGHTS RESERVED
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|