Datalogic Scanning QUICKSCAN QD 2300 User Manual

QuickScan® L  
QD 2300 Bar Code Scanner  
Product Reference Guide  
Table of Contents  
Chapter 1. Introduction.............................................................................................................. 1  
About this Guide .................................................................................................................... 1  
Manual Overview ................................................................................................................... 1  
Manual Conventions ............................................................................................................... 2  
References ............................................................................................................................ 3  
Technical Support .................................................................................................................. 3  
Datalogic Website Support ................................................................................................. 3  
Reseller Technical Support ................................................................................................. 3  
Telephone Technical Support .............................................................................................. 3  
Chapter 2. Getting Started ......................................................................................................... 5  
About the Scanner ................................................................................................................. 5  
Unpacking ............................................................................................................................. 5  
Setting Up the Scanner ........................................................................................................... 6  
Installing the Interface Cable ............................................................................................. 6  
Removing the Interface Cable ............................................................................................ 7  
Connecting Power (if required) ........................................................................................... 7  
Configuring the Scanner .................................................................................................... 7  
Chapter 3. Operation.................................................................................................................. 9  
Nomenclature ........................................................................................................................ 9  
LED and Beeper Indications ....................................................................................................10  
Scan Mode ...........................................................................................................................11  
Scanning .............................................................................................................................12  
Aiming .................................................................................................................................12  
Depth of Field .......................................................................................................................14  
Maintenance .........................................................................................................................14  
Chapter 4. Problem Isolation ................................................................................................... 15  
Problem Isolation ..................................................................................................................15  
Chapter 5. General Features..................................................................................................... 19  
User Preferences ...................................................................................................................19  
Scanning Sequence Examples .................................................................................................19  
Errors While Scanning ...........................................................................................................19  
User General Feature Defaults ................................................................................................20  
Default Parameters ...............................................................................................................21  
Restore Defaults ..............................................................................................................21  
Beeper Tone .........................................................................................................................22  
Beeper Volume .....................................................................................................................22  
Power Mode .........................................................................................................................23  
Scan Mode ...........................................................................................................................23  
Stand Mode Timeout Period ..............................................................................................24  
Scan Line Width ....................................................................................................................25  
Laser On Time ......................................................................................................................25  
Beep After Good Read ...........................................................................................................26  
Transmit Label ID .................................................................................................................26  
Prefix/Suffix Values ...............................................................................................................27  
Global Prefix/Suffix ...............................................................................................................28  
FN1 Substitution Values .........................................................................................................30  
Transmit “No Read” Message ..................................................................................................30  
Product Reference Guide  
i
Chapter 6. RS-232 ................................................................................................................... 31  
Introduction ......................................................................................................................... 31  
Connecting an RS-232 Interface ............................................................................................. 32  
RS-232 Parameter Defaults .................................................................................................... 33  
RS-232 Host Parameters ....................................................................................................... 33  
RS-232 Host Types ......................................................................................................... 36  
Baud Rate ...................................................................................................................... 37  
Parity ............................................................................................................................ 38  
Stop Bit Select ................................................................................................................ 39  
Data Bits (ASCII Format) ................................................................................................. 39  
Check Receive Errors ....................................................................................................... 40  
Hardware Handshaking .................................................................................................... 41  
Software Handshaking ..................................................................................................... 43  
Host Serial Response Time-out ......................................................................................... 45  
RTS Line State ................................................................................................................46  
Beep on <BEL> .............................................................................................................. 46  
Intercharacter Delay ........................................................................................................ 47  
Nixdorf Beep/LED Options ................................................................................................ 48  
Ignore Unknown Characters ............................................................................................. 48  
ASCII Character Set for RS-232 .............................................................................................. 49  
Chapter 7. Keyboard Wedge Interface..................................................................................... 55  
Connecting a Keyboard Wedge Interface .................................................................................. 55  
Keyboard Wedge Parameter Defaults ...................................................................................... 56  
Keyboard Wedge Host Parameters .......................................................................................... 57  
Keyboard Wedge Host Types ............................................................................................ 57  
Keyboard Wedge Country Types (Country Codes) ................................................................ 58  
Ignore Unknown Characters ............................................................................................. 59  
Keystroke Delay ............................................................................................................. 60  
Intra-Keystroke Delay ..................................................................................................... 60  
Alternate Numeric Keypad Emulation ................................................................................. 61  
Caps Lock On ................................................................................................................. 61  
Caps Lock Override ......................................................................................................... 62  
Convert Wedge Data ....................................................................................................... 62  
Function Key Mapping ...................................................................................................... 63  
FN1 Substitution ............................................................................................................. 63  
Send Make and Break ...................................................................................................... 63  
Keyboard Maps ............................................................................................................... 64  
ASCII Character Set for Keyboard Wedge ................................................................................ 64  
Chapter 8. USB Interface......................................................................................................... 75  
Connecting a USB Interface ................................................................................................... 75  
USB Parameter Defaults ........................................................................................................76  
USB Host Parameters ............................................................................................................ 77  
USB Device Type ............................................................................................................ 77  
USB Country Keyboard Types (Country Codes) ................................................................... 78  
USB Keystroke Delay ....................................................................................................... 80  
USB CAPS Lock Override .................................................................................................. 80  
USB Ignore Unknown Characters ....................................................................................... 81  
Emulate Keypad .............................................................................................................. 81  
USB Keyboard FN 1 Substitution ....................................................................................... 82  
Function Key Mapping ...................................................................................................... 82  
Simulated Caps Lock ....................................................................................................... 83  
Convert Case ..................................................................................................................83  
ASCII Character Set for USB .................................................................................................. 84  
Chapter 9. Symbologies........................................................................................................... 95  
Introduction ......................................................................................................................... 95  
Scanning Sequence Examples ................................................................................................ 95  
ii  
QuickScan® L  
Errors While Scanning ...........................................................................................................95  
Symbology Parameter Defaults ...............................................................................................96  
UPC/EAN ..............................................................................................................................99  
Enable/Disable UPC-A/UPC-E ............................................................................................99  
Enable/Disable UPC-E1 ...................................................................................................100  
Enable/Disable EAN-13/EAN-8 .........................................................................................101  
Enable/Disable Bookland EAN ..........................................................................................101  
Decode UPC/EAN/JAN Supplementals ...............................................................................102  
UPC/EAN/JAN Supplemental Redundancy ..........................................................................104  
Transmit UPC-A Check Digit ............................................................................................104  
Transmit UPC-E Check Digit ............................................................................................105  
Transmit UPC-E1 Check Digit ..........................................................................................105  
UPC-A Preamble ............................................................................................................106  
UPC-E Preamble ............................................................................................................107  
UPC-E1 Preamble ..........................................................................................................108  
Convert UPC-E to UPC-A .................................................................................................109  
Convert UPC-E1 to UPC-A ...............................................................................................109  
EAN-8/JAN-8 Extend ......................................................................................................110  
UCC Coupon Extended Code ............................................................................................110  
Code 128 ...........................................................................................................................111  
Enable/Disable Code 128 ................................................................................................111  
Enable/Disable UCC/EAN-128 ..........................................................................................111  
Enable/Disable ISBT 128 ................................................................................................112  
Code 39 .............................................................................................................................112  
Enable/Disable Code 39 ..................................................................................................112  
Enable/Disable Trioptic Code 39 ......................................................................................113  
Convert Code 39 to Code 32 ...........................................................................................113  
Code 32 Prefix ..............................................................................................................114  
Set Lengths for Code 39 .................................................................................................114  
Code 39 Check Digit Verification ......................................................................................116  
Transmit Code 39 Check Digit .........................................................................................116  
Code 39 Full ASCII Conversion ........................................................................................117  
Code 39 Buffering (Scan & Store) ....................................................................................118  
Code 93 .............................................................................................................................120  
Enable/Disable Code 93 ..................................................................................................120  
Set Lengths for Code 93 .................................................................................................121  
Code 11 .............................................................................................................................122  
Set Lengths for Code 11 .................................................................................................123  
Code 11 Check Digit Verification ......................................................................................125  
Transmit Code 11 Check Digits ........................................................................................126  
Interleaved 2 of 5 (ITF) .......................................................................................................126  
Enable/Disable Interleaved 2 of 5 ....................................................................................126  
Set Lengths for Interleaved 2 of 5 ....................................................................................127  
I 2 of 5 Check Digit Verification .......................................................................................129  
Transmit I 2 of 5 Check Digit ..........................................................................................129  
Convert I 2 of 5 to EAN-13 .............................................................................................130  
Discrete 2 of 5 (DTF) ...........................................................................................................130  
Enable/Disable Discrete 2 of 5 .........................................................................................130  
Set Lengths for Discrete 2 of 5 ........................................................................................131  
Chinese 2 of 5 ....................................................................................................................132  
Enable/Disable Chinese 2 of 5 .........................................................................................132  
Codabar (NW - 7) ...............................................................................................................133  
Enable/Disable Codabar ..................................................................................................133  
Set Lengths for Codabar .................................................................................................133  
CLSI Editing ..................................................................................................................135  
NOTIS Editing ...............................................................................................................136  
MSI ...................................................................................................................................136  
Enable/Disable MSI ........................................................................................................136  
Set Lengths for MSI .......................................................................................................137  
MSI Check Digits ...........................................................................................................138  
Product Reference Guide  
iii  
Transmit MSI Check Digit(s) ........................................................................................... 139  
MSI Check Digit Algorithm .............................................................................................. 139  
GS1 DataBar (RSS) ............................................................................................................ 140  
Convert DataBar to UPC/EAN .......................................................................................... 141  
Symbology - Specific Security Levels ..................................................................................... 142  
Redundancy Level ......................................................................................................... 142  
Security Level ............................................................................................................... 144  
Symbology - Intercharacter Gap ........................................................................................... 146  
Appendix A. Technical Specifications..................................................................................... 147  
Standard Cable Pinouts ....................................................................................................... 149  
Appendix B. Standard Defaults .............................................................................................. 151  
Appendix C. Programming Reference..................................................................................... 157  
Datalogic Label ID Identifiers ............................................................................................... 157  
AIM Label ID Identifiers ....................................................................................................... 157  
Appendix D. Sample Bar Codes.............................................................................................. 161  
UPC/EAN ........................................................................................................................... 161  
UPC-A, 100% ............................................................................................................... 161  
EAN-13, 100% ............................................................................................................. 161  
Code 128 .......................................................................................................................... 161  
Code 39 ............................................................................................................................ 162  
Code 93 ............................................................................................................................ 162  
Code 11 ............................................................................................................................ 162  
Interleaved 2 of 5 ............................................................................................................... 162  
Discrete 2 of 5 (DTF) .......................................................................................................... 163  
Chinese 2 of 5 .................................................................................................................... 163  
Codabar ............................................................................................................................ 163  
MSI .................................................................................................................................. 163  
DataBar (RSS) ................................................................................................................... 164  
DataBar Omnidirectional ................................................................................................ 164  
Appendix E. Keypad............................................................................................................... 165  
Cancel .............................................................................................................................. 166  
Appendix F. ASCII Character Sets.......................................................................................... 167  
Appendix G. RS-232 Host Commands..................................................................................... 179  
Index ..................................................................................................................... 181  
iv  
QuickScan® L  
Chapter 1  
Introduction  
About this Guide  
This manual presents advanced user information which includes connection, program-  
ming, maintenance, technical specifications, and other useful references. For additional  
user information, see the Quick Reference Guide (QRG). Copies of other publications  
for this product are downloadable free of charge from the website listed on the back cover  
of this manual.  
On leaving the factory, units are generally programmed for the most common terminal  
and communications settings. If you need to change these settings, custom program-  
ming can be accomplished by scanning the bar codes in this guide.  
Manual Overview  
Chapter 1, Introduction provides a product overview, unpacking instructions, and cable  
connection information.  
Chapter 2, Getting Started presents information about unpacking and setting up the  
scanner.  
Chapter 3, Operation describes parts of the scanner, beeper and LED definitions, and  
how to use the scanner in Trigger Single and Stand modes.  
Chapter 4, Problem Isolation outlines troubleshooting procedures addressing various  
problems.  
Chapter 5, General Features includes programming bar codes for selecting common  
features for the scanner and general use bar codes to customize how the data is transmit-  
ted to the host device.  
Chapter 6, RS-232 supplies information about setting up the scanner for RS-232 oper-  
ation.  
Chapter 7, Keyboard Wedge Interface discusses how to set up the scanner for Keyboard  
Wedge operation.  
Chapter 8, USB Interface explains how to set up the scanner for USB operation.  
Chapter 9, Symbologies defines options for all symbologies and provides the program-  
ming bar codes necessary for configuring these features.  
Appendix A, Technical Specifications lists physical and performance characteristics, as  
well as environmental and regulatory specifications. It also provides standard cable pin-  
outs.  
Appendix B, Standard Defaults references common factory default settings for scanner  
features and options.  
Product Reference Guide  
1
Introduction  
Appendix C, Programming Reference is a listing of AIM code identifiers, ASCII char-  
acter conversions and keyboard maps.  
Appendix D, Sample Bar Codes offers sample bar codes of several common symbolo-  
gies.  
Appendix E, Keypad includes numeric bar codes to be scanned for certain parameter set-  
tings.  
Appendix F, ASCII Character Sets provides ASCII character value tables.  
Appendix G, RS-232 Host Commands lists host commands the scanner will respond to  
when in RS-232 interface mode.  
Manual Conventions  
The following conventions are used in this document:  
Italics are used to highlight the following:  
Chapters and sections in this and related documents  
Dialog box, window and screen names  
Drop-down list and list box names.  
Bold text is used to highlight the following:  
Key names on a keypad.  
Bullets (•) indicate:  
Action items  
Lists of alternatives  
Lists of required steps that are not necessarily sequential  
Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered  
lists.  
Throughout the programming bar code menus, asterisks (*) are used to denote default  
parameter settings.  
Feature/Option  
* Indicates  
*Baud Rate 9600  
2
QuickScan® L  
References  
The symbols listed below are used in this manual to notify the reader of key issues or  
procedures that must be observed when using the scanner:  
Notes contain information necessary for properly diagnosing, repair-  
ing and operating the scanner.  
NOTE  
The CAUTION symbol advises you of actions that could damage  
equipment or property.  
CAUTION  
References  
Current versions of the Product Reference Guide (PRG), Quick Reference Guide  
(QRG), and any other manuals and instruction sheets for this product can be download-  
ed from the website listed on the back cover of this manual. Alternatively, printed copies  
or product support CDs can be purchased through your Datalogic reseller.  
Technical Support  
Datalogic Website Support  
The Datalogic website (www.scanning.datalogic.com) is the complete source for technical  
support and information for Datalogic products. The site offers product support, prod-  
uct registration, warranty information, product manuals, product tech notes, software  
updates, demos, and instructions for returning products for repair.  
Reseller Technical Support  
An excellent source for technical assistance and information is an authorized Datalogic  
reseller. A reseller is acquainted with specific types of businesses, application software,  
and computer systems and can provide individualized assistance.  
Telephone Technical Support  
If you do not have internet or email access, you may contact Datalogic technical support  
at (541) 349-8283 or check the back cover of your manual for more contact information.  
Product Reference Guide  
3
Introduction  
NOTES  
4
QuickScan® L  
Chapter 2  
Getting Started  
About the Scanner  
The scanner combines excellent scanning performance and advanced ergonomics to provide the  
best value in a lightweight laser scanner. Whether used in Trigger Single or Stand mode, the  
scanner ensures comfort and ease of use for extended periods of time.  
This scanner does not support PDF417 bar codes and its variants.  
NOTE  
This scanner supports the following interfaces:  
Keyboard Wedge connection to a host. The host interprets scanned data as keystrokes.  
This interface supports the following international keyboards (for Windows® environ-  
ment): North America, German, French, French Canadian, Spanish, Italian, Swedish, UK  
English, Portuguese-Brazilian, and Japanese.  
Standard RS-232 connection to a host. Scan bar code menus to set up proper communi-  
cation of the scanner with the host.  
The scanner uses TTL RS-232 signal levels, which will interface with most  
system architectures.  
NOTE  
USB connection to a host. The scanner autodetects a USB host and defaults to the HID  
keyboard interface type. Select other USB interface types by scanning programming bar  
code menus.This interface supports the following international keyboards (for Win-  
dows® environment): North America, German, French, French Canadian, Spanish, Ital-  
ian, Swedish, UK English, Portuguese-Brazilian, and Japanese.  
Unpacking  
Verify that the scanner and any accessories are what were ordered and that they are undamaged.  
If any damage occurred in transit, contact Technical Support on page 3.  
KEEP THE PACKAGING. Should the unit ever require service, it should be returned in its  
original shipping container.  
Product Reference Guide  
5
Getting Started  
Setting Up the Scanner  
Installing the Interface Cable  
To connect the interface cable:  
1. Insert the interface cable’s modular connector clip into the cable interface port on the bot-  
tom of the scanner handle. (See Figure 1).  
2. Gently tug the cable to ensure the connector is properly secured.  
3. Connect the other end of the interface cable to the host. (See the specific host chapter for  
information on host connections.)  
Figure 1. Connecting the Interface Cable  
Bottom of Scanner  
Cable  
Interface Cable Port  
Cable Strain Relief  
To Host  
Cable Clip (Latch)  
Specific cables are required for connection to different hosts. The  
connectors illustrated in each host chapter are examples only. Actual  
connectors may vary from those illustrated, but the steps to connect  
the scanner remain the same.  
NOTE  
6
QuickScan® L  
Setting Up the Scanner  
Removing the Interface Cable  
To remove the Interface Cable:  
1. Unlatch the installed cable modular connector by depressing the connector clip with the  
end of a paper clip as shown in Figure 2.  
Figure 2. Releasing the Cable Latch  
Insert a paperclip  
into this hole to  
release the  
cable latch  
Strain Relief  
Cable  
2. Carefully slide out the cable.  
3. Follow the steps in the previous section, Installing the Interface Cable, to connect a  
new cable.  
Connecting Power (if required)  
If the host does not provide power to the scanner, an external power connection to the scanner is  
required. To connect power:  
1. Connect the interface cable to the bottom of the scanner, as previously described in the  
section, Installing the Interface Cable.  
2. Connect the other end of the interface cable to the host (refer to the host manual to locate  
the correct port).  
3. Plug the power supply into the power jack on the interface cable. Plug the other end of the  
power supply into an AC outlet.  
Configuring the Scanner  
To configure the scanner, use the bar codes included in this manual.  
See Chapter 5, General Features and Chapter 9, Symbologies for information about  
programming the scanner using bar code menus. Also see each host-specific chapter to set up a  
connection to a specific host type.  
Product Reference Guide  
7
Getting Started  
NOTES  
8
QuickScan® L  
Chapter 3  
Operation  
This chapter provides beeper and LED definitions, techniques involved in scanning bar codes,  
general instructions and tips about scanning, and decode zone diagrams.  
Nomenclature  
Nomenclature for physical features on the scanner is shown in Figure 3.  
Figure 3. Nomenclature  
LED  
Scan  
Window  
Trigger  
Product Reference Guide  
9
Operation  
LED and Beeper Indications  
The scanner’s beeper sounds and its two-color LED illuminates to indicate various functions or  
errors on the scanner. The tables below list these indications. One exception to the behaviors  
listed in the tables is that the scanner’s functions are programmable, and may or may not be  
turned on. For example, certain indications, such as the power-up beep can be disabled using  
programming bar code labels.  
Table 1. Beeper Functions  
Beeper Sequence  
Indication  
Standard Use  
Low/medium/high beeps  
Short high beeps  
Power up.  
A bar code label was decoded (if decode beeper is enabled).  
A transmission error was detected in a scanned bar code. The data is  
ignored. This occurs if a unit is not properly configured. Check option  
setting.  
4 long low beeps  
5 low beeps  
Conversion or format error.  
Advanced Data Formatting (ADF) transmit error. (For information about  
ADF programming, refer to Technical Support.)  
Low/high/low beeps  
High/high/high/low beeps  
Parameter Menu Scanning  
Short high beeps  
RS-232 receive error.  
Correct entry scanned or correct menu sequence performed.  
Input error, incorrect bar code or “Cancel” scanned, wrong entry, incor-  
rect bar code programming sequence; remain in Programming Mode.  
Low/high beeps  
High/low beeps  
Keyboard parameter selected. Enter value using bar code keypad.  
Successful program exit with change in the parameter setting.  
High/low/high/low beeps  
Out of host parameter storage space. Scan Default Parameters on  
page 21.  
Low/high/low/high beeps  
Code 39 Buffering  
High/low beeps  
New Code 39 data was entered into the buffer.  
Code 39 buffer is full.  
3 Beeps - long high beeps  
The Code 39 buffer was erased or there was an attempt to clear or  
transmit an empty buffer.  
Low/high/low beeps  
Low/high beeps  
Host Specific  
USB Only  
A successful transmission of buffered data.  
10  
QuickScan® L  
Scan Mode  
Table 1. Beeper Functions  
Beeper Sequence  
Indication  
Scanner has not completed initialization. Wait several seconds and scan  
again.  
4 short high beeps  
Scanner gives a power-up beep after scanning a USB Communication with the bus must be established before the scanner  
Device Type.  
can operate at the highest power level.  
The USB bus may put the scanner in a state where power to the scanner  
is cycled on and off more than once. This is normal and usually happens  
when the host cold boots.  
This power-up beep occurs more than once.  
RS-232 Only  
1 short high beep  
A <BEL> character is received and Beep on <BEL> is enabled.  
Table 2. LED Indications  
LED Sequence  
Indication  
No power is applied to the scanner, or the scanner is on and ready to  
scan.  
Off  
Green  
Red  
A bar code was successfully decoded.  
A data transmission error or scanner malfunction occurred.  
Scan Mode  
The scanner can be configured to be active in one of two Scan Modes:  
Trigger Single Mode — the trigger button must be pressed to scan a bar code.  
Stand Mode — the scanner continuously reads regardless of whether the trigger is pressed  
When the scanner is not used for an extended period of time in Stand  
Mode, it enters Sleep Mode. To wake the scanner, press the trigger  
button.  
NOTE  
To toggle between these modes, see Scan Mode on page 23.  
Product Reference Guide  
11  
Operation  
Scanning  
To scan a bar code:  
1. Install and program the scanner (See “Setting Up the Scanner” on page 6.). For  
assistance, contact Technical Support.  
2. Ensure all connections are secure. (See the host chapter for the scanner.)  
3. Aim the scanner at the bar code.  
4. If the scanner is in Trigger Single Mode, press the trigger button. (In Stand Mode, no trig-  
ger button press is required. The scanner laser is in constant ON mode.)  
Figure 4. Scanning With/Without the Trigger  
Trigger Single Mode Stand Mode  
Push Trigger to  
initiate scan.  
Trigger push  
not required.  
5. Upon successful decode, the scanner beeps and the LED flashes green. (For more informa-  
tion about beeper and LED definitions, see Table 1 and Table 2.)  
The width of the scan line is dependent upon the current setting for  
the programmable feature, Scan Line Width. “Full” (the default set-  
ting) or “Medium” scan line widths are available.  
NOTE  
Aiming  
For a typical, full-sized UPC label, the scanner should be held between 1” and 7” from the bar  
code. Ensure that the scan line crosses the entire bar code as shown in Figure 5.  
Figure 5. Correct and Incorrect Aiming  
012345  
012345  
The scan line is smaller when the scanner is closer to the bar code and grows when the scanner is  
drawn away from the bar code. For best results, hold the scanner closer to bar codes with very  
small bars or elements (mil size) and pull the scanner further away from labels having larger bars  
or elements (mil size).  
12  
QuickScan® L  
Aiming  
Do not hold the scanner perpendicular to the bar code when scanning. Laser light reflecting  
directly back into the scanner from the bar code can result in specular reflection, which can in  
turn cause difficulties with decoding. Tilt the scanner to avoid the dead zone (indicated by an  
‘X’ in Figure 6) up to 65 degrees upwards or downwards.  
Figure 6. Aiming to Avoid the Dead Zone  
65°  
65°  
Product Reference Guide  
13  
Operation  
Depth of Field  
Figure 7 shows the zone in which bar codes are read by the scanner.  
Figure 7. Depth of Field Chart  
NOTE: Typical performance at 73° F (23°C) on  
high quality bar codes in normal room light.  
in.  
6
cm  
15.24  
W
I
D
T
H
O
F
0
0
F
I
E
L
D
6
15.24  
5 mil  
0.4"  
0.1"  
5.5"  
7.5 mil  
10 mil  
7.8"  
8.6"  
9.1"  
13 mil 100% UPC  
20 mil  
10.6"  
*
5
12.7  
in.  
cm  
0
0
10  
25.4  
15  
38.1  
DEPTH OF FIELD  
* Minimum distance determined by bar code length and scan angle  
Maintenance  
Periodic cleaning of the scan window is the only maintenance required. A dirty window may  
affect scanning ability.  
Do not allow any abrasive material to touch the scanner.  
Remove any dirt particles with a soft, lint-free cloth lightly dampened with water.  
Gently wipe the window using a lens tissue moistened with ammonia/water.  
Do not spray water or other cleaning liquids directly onto the scanner or window.  
If the scan window becomes scratched, broken or contaminated with heavy dust, replace  
with a new window, which is available as an orderable accessory.  
14  
QuickScan® L  
Chapter 4  
Problem Isolation  
This chapter provides troubleshooting information, technical specifications, and signal descrip-  
tions (pinouts).  
Problem Isolation  
Table 3 provides problem/remedy information for use in troubleshooting scanner functions.  
Table 3. Troubleshooting  
Problem  
Possible Causes  
Possible Solutions  
Beeper Indications (Also see LED and Beeper Indications on page 10)  
The USB bus may put the scanner in a  
Scanner emits frequent beeps. (USB  
host interface only.)  
This is normal and usually happens when  
the host cold boots.  
state where power to the scanner is  
cycled on and off more than once.  
ADF transmit error.  
Scanner emits low/high/low beeps.  
Invalid ADF rule is detected.  
Refer to the Advanced Data Formatting Pro-  
grammer’s Guide for information about ADF  
programming.  
Input error, incorrect bar code or Cancel Scan the correct numeric bar codes within  
bar code was scanned. range for the parameter programmed.  
Scanner emits low/high beeps.  
The Code 39 buffer was erased or there Normal when scanning the Code 39 Buffer-  
was an attempt to clear or transmit an  
empty buffer.  
Scanner emits low/high/low beeps.  
ing Clear Buffer bar code or upon attempt  
to transmit an empty Code 39 buffer.  
Out of host parameter storage space.  
Out of memory for ADF rules.  
Scan Default Parameters on page 21.  
Scanner emits low/high/low/high beeps.  
Scanner emits high/low beeps.  
Reduce the number of ADF rules or the  
number of steps in the ADF rules.  
The scanner is buffering Code 39 data.  
Normal.  
Normal during host reset. Otherwise, set the  
scanner's RS-232 parity to match the host  
setting.  
Scanner emits high/high/high/low  
beeps.  
RS-232 receive error.  
A transmission error was detected in a  
scanned bar code. The data is ignored.  
This occurs if a unit is not properly config-  
ured. Verify programmed options.  
Scanner emits four long low beeps.  
Scanner emits four short high beeps  
(USB only).  
Scanner has not completed initialization. Wait several seconds and scan again.  
Product Reference Guide  
15  
Problem Isolation  
Problem  
Possible Causes  
Possible Solutions  
Scanner emits a short low/high/low/high  
beep sequence while it is being pro-  
grammed.  
Erase all rules and re-program with shorter  
rules.  
Out of ADF parameter storage space.  
Decoding Bar Codes  
Program the scanner to read that type of bar  
code. See Chapter 9, Symbologies.  
Scanner is not programmed for the cor-  
rect bar code type.  
Scan other samples of the same bar code  
type to determine if the bar code is defaced.  
Bar code is unreadable.  
Scanner emits laser light, but does not  
decode the bar code.  
Move the scanner closer to or further from  
the bar code. See Depth of Field on page  
14.  
Distance between scanner and bar code  
is incorrect.  
Move the bar code until the scan line is  
within the acceptable aiming pattern. See  
Figure 5.  
The scan line is not crossing every bar  
and space of the bar code.  
Scan the appropriate host type program-  
ming bar code. See the chapter correspond-  
ing to the host type.  
Scanner is not programmed for the cor-  
rect host type.  
Scanner decodes bar code, but does not  
transmit the data to the host.  
Check for loose cable connection and re-  
connect cable.  
Interface cable is loose.  
Conversion or format error was detected.  
Ensure the scanner’s conversion parame-  
ters are properly configured.  
The scanner’s conversion parameters  
are not properly configured.  
Conversion or format error was detected.  
Scanner emits five long low beeps after  
a bar code is decoded.  
Change the ADF rule, or change to a host  
that can support the ADF rule.  
An ADF rule was set up with characters  
that can't be sent for the host selected.  
Conversion or format error was detected.  
Change the bar code, or change to a host  
A bar code was scanned with characters that can support the bar code.  
that can't be sent for that host.  
16  
QuickScan® L  
Problem Isolation  
Problem  
Possible Causes  
Possible Solutions  
Host Error  
Ensure the proper host is selected.  
Scan the appropriate host type program-  
ming bar code.  
For RS-232, set the scanner's communica-  
tion parameters to match the host's settings.  
Scanner is not programmed to work with For a USB HID keyboard or Keyboard  
Host displays scanned data incorrectly.  
the host.  
Wedge configuration, program the system  
for the correct keyboard type and language,  
and turn off the CAPS LOCK key.  
Program the proper editing options (e.g.,  
ADF, UPC-E to UPC-A Conversion).  
Check the scanner’s host type parameters  
or editing options.  
Trigger  
Verify that system power is sufficient. If the  
scanner requires a power supply, reconnect  
using an approved power supply.  
No power to the scanner.  
Nothing happens when the trigger but-  
ton is pressed.  
Check for loose cable connections and re-  
connect cables.  
Interface/power cables are loose.  
Incorrect host interface cable is used.  
Verify that the correct host interface cable is  
used. If not, connect the correct host inter-  
face cable.  
If the problem persists after performing these checks, contact your  
distributor or Technical Support.  
NOTE  
Product Reference Guide  
17  
Problem Isolation  
NOTES  
18  
QuickScan® L  
Chapter 5  
General Features  
User Preferences  
User preferences for the general features listed in this chapter can be selected using the  
programming bar codes that accompany each feature description. To set feature values,  
scan a single programming bar code or a short bar code sequence as instructed for each  
feature. The settings are stored in non-volatile memory and are preserved even when the  
scanner is powered down.  
Typically, a scanner ships with the settings shown in User General Feature Defaults  
on page 20 (also see Appendix B, Standard Defaults for all host defaults). If the de-  
fault values suit requirements, programming may not be necessary.  
If not using a USB cable, select a host type (see each host chapter for specific host infor-  
mation) after the power-up beeps sound. This is only necessary upon the first power-up  
when connecting to a new host.  
To return all features to their default values, reference the topic, Return to Factory De-  
faults. Throughout the programming bar code menus, default values are indicated with  
asterisks (*).  
*High Frequency  
Feature/Option  
* Indicates Default  
Scanning Sequence Examples  
In most cases, scanning one bar code sets the parameter value. For example, to set the  
beeper tone to high, scan the High Frequency (beeper tone) bar code on page 19. The  
scanner issues a fast warble beep and the LED turns green, signifying a successful param-  
eter entry.  
Other parameters, such as Serial Response Time-Out or Data Transmission Formats, re-  
quire the scanning of a sequence of bar codes. See these parameter descriptions for this  
procedure.  
Errors While Scanning  
Unless otherwise specified, when an error is made during a scanning sequence, just re-  
scan the correct feature bar code(s).  
Product Reference Guide  
19  
General Features  
User General Feature Defaults  
Table 4 lists the factory defaults for the general features described in this chapter, plus  
provides a place for you to log any special requirements or user-preferred settings at your  
installation. To change any option, scan the appropriate programming bar code(s) pro-  
vided in this chapter.  
See Appendix B, Standard Defaults for a listing of all programmable  
features.  
NOTE  
Table 4. General Feature Defaults  
Standard Factory  
Default  
General Feature  
Beeper Tone  
Page Number  
Record Your Setting  
Medium  
22  
22  
23  
23  
25  
25  
26  
26  
27  
27  
26  
30  
30  
Beeper Volume  
Power Mode  
High  
Continuous On  
Trigger Single  
Full Width  
3.0 Sec  
Scanning Mode  
Scan Line Width  
Laser On Time  
Beep After Good Decode  
Transmit Label ID Character  
Prefix Value  
Enable  
None  
7013 <CR><LF>  
7013 <CR><LF>  
Suffix Value  
Scan Data Transmission Format Data as is  
FN1 Substitution Values  
Set  
Transmit “No Read” Message  
Disable  
20  
QuickScan® L  
Default Parameters  
Default Parameters  
The scanner can be reset using one of two default settings: factory defaults or custom de-  
faults. Scan the appropriate bar code(s) below to reset the scanner to its default settings  
and/or set the scanner’s current settings as the custom default.  
Set Factory Defaults — Scan the Set Factory Defaults bar code below to eliminate all  
custom default values and return the scanner to factory default values. (For factory de-  
fault values, see Appendix B, Standard Defaults.)  
Write to Custom Defaults — Custom default parameters can be configured to set  
unique default values for all parameters. After changing all parameters to the desired de-  
fault values, scan the Write to Custom Defaults bar code below to configure custom de-  
faults.  
Restore Defaults  
Resets all default parameters as follows:  
If custom default values were configured (see Write to Custom Defaults above), the cus-  
tom default values are set for all parameters each time the Restore Defaults bar code below  
is scanned.  
If no custom default values were configured, the factory default values are set for all  
parameters each time the Restore Defaults bar code below is scanned. (For factory default  
values, see Appendix B, Standard Defaults.)  
Set Factory Defaults  
Write to Custom Defaults  
*Restore Defaults  
Product Reference Guide  
21  
General Features  
Beeper Tone  
To select a decode beep frequency (tone), scan the Low Frequency, Medium Frequency,  
or High Frequency bar code.  
Low Frequency  
*Medium Frequency  
(Optimum Settings)  
High Frequency  
Beeper Volume  
To select a beeper volume, scan the Low Volume, Medium Volume, or High Volume  
bar code.  
Low Volume  
Medium Volume  
*High Volume  
22  
QuickScan® L  
Power Mode  
Power Mode  
This parameter determines whether or not power remains on after a decode attempt.  
When in reduced power mode, the scanner enters low power consumption mode after  
each decode. When in continuous power mode, power remains on after each decode.  
*Continuous On  
Reduced Power Mode  
Scan Mode  
This parameter determines whether the scanner is in Trigger Single Mode or Stand Mode.  
In Trigger Single Mode, the scanner trigger button must be pressed to decode each  
scanned bar code. In Stand Mode, the scanner laser is in constant ON state and no trigger  
button press is required to scan a bar code.  
Depending upon which mode the scanner currently is in, scan the “Toggle Scan Mode”  
to switch from Trigger Single to Stand Mode, or from Stand Mode to Trigger Single Mode.  
The standard default setting for this feature is Trigger Single Mode.  
While in the Stand Mode of operation, if the scanner has not been used for several min-  
utes it will shift to low power operation, signalled by a narrowing of the scanning beam.  
When in low power mode, the scanner will respond to a barcode and come back to nor-  
mal Stand Mode operation upon seeing/reading the label.  
1
If the scanner has been idle for an extended configurable period , it will timeout, then  
enter sleep mode with the scanning beam turned off. To wake the scanner from sleep  
mode, press the trigger button.  
*Toggle Scan Mode  
1. See the following topic Stand Mode Timeout Period.  
Product Reference Guide  
23  
General Features  
Stand Mode Timeout Period  
The Timeout Period for the transition from low power to sleep mode can be set to one  
of the following durations:  
1 Hour  
5 Hours (default)  
Infinite Timeout — With this setting, there is no timeout, thus the scanner will never go  
into sleep mode or beam shut-off but will remain in low power mode until a label is read.  
Stand Mode Timeout Period = 1 Hour  
*Stand Mode Timeout Period = 5 Hours  
Stand Mode Timeout Period = Infinite Timeout  
24  
QuickScan® L  
Scan Line Width  
Scan Line Width  
Scan a bar code below to set the scan line width. A full scan line width is the default. The  
medium scan line width is useful for scanning menus or pick-lists.  
This feature applies to scanners in Trigger Single Mode only.  
NOTE  
*Full Width  
Medium Width  
Laser On Time  
This parameter sets the maximum time that decode processing continues during a scan  
attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The de-  
fault Laser On Time is 3.0 seconds.  
To set a Laser On Time, scan the bar code below. Next, scan the two numeric bar codes  
from Appendix E, Keypad, that correspond to the desired On Time. Single digit num-  
bers must be padded with a leading zero. For example, to set an On Time of 0.5 seconds,  
scan the bar code below, then scan the “0” and “5” bar codes. If an error is made, or the  
selection needs to be changed, scan Cancel on page 166.  
This feature applies to scanners in Trigger Single Mode only.  
NOTE  
Laser On Time  
Product Reference Guide  
25  
General Features  
Beep After Good Read  
Scan a bar code below to select whether or not the scanner should beep after a good read.  
If Do Not Beep After Good Read is selected, the beeper still operates during parameter  
menu scanning and indicates error conditions.  
*Beep After Good Read  
(Enable)  
Do Not Beep After Good Read  
(Disable)  
Transmit Label ID  
Label ID characters identify the code (symbology) type of a scanned bar code. This may  
be useful when the scanner is decoding more than one code type. In addition to any sin-  
gle character prefix already selected, the Label ID character is inserted between the prefix  
and the decoded bar code.  
Select no Label ID character, a Datalogic Label ID, or an AIM Label ID. For a listing of  
Label ID Characters, see Datalogic Label ID Identifiers on page 157 and AIM La-  
bel ID Identifiers on page 157.  
Datalogic Label ID  
AIM Label ID  
*No Label ID  
26  
QuickScan® L  
Prefix/Suffix Values  
Prefix/Suffix Values  
A prefix and/or suffix can be appended to scan data for use in data editing as described  
in the feature description, Global Prefix/Suffix on page 28.  
To set a value for a prefix or suffix:  
1. Change the scan data format using the instructions in the feature description, Global  
Prefix/Suffix on page 28.  
2. Scan the appropriate prefix/suffix bar code below.  
3. Scan a four-digit number (i.e., four bar codes from Appendix E, Keypad) that corre-  
sponds to that value.  
When using host commands to set the prefix or suffix, set the key  
category parameter to 1, then set the 3-digit decimal value corre-  
sponding to the desired keystroke as listed in Table 34 on page 167  
(results in a four-digit ASCII code).  
NOTE  
4. To correct an error or change a selection, scan Data Format Cancel on page 29.  
Set Prefix  
Set Suffix  
Product Reference Guide  
27  
General Features  
Global Prefix/Suffix  
ASCII characters may be added as a prefix (in a position before the bar code data) and/  
or as a suffix (in a position following the bar code data). Scan the bar code below labeled  
“Scan Options”, then one of the following four bar codes corresponding to the posi-  
tion(s) you wish to specify:  
Data As Is  
<DATA> <SUFFIX>  
<PREFIX> <DATA>  
<PREFIX> <DATA> <SUFFIX>.  
Scan the “Enter” bar code to complete the change. To set values for the prefix and/or  
suffix, See Prefix/Suffix Values on page 27. Scan the bar code “Data Format Can-  
cel” if you wish to cancel the change.  
If a carriage return/enter is required after each scanned bar code, scan the following bar  
codes in order:  
1. “Scan Options”  
2. <DATA> <SUFFIX>  
3. “Enter”  
Scan Options  
*Data As Is  
<DATA> <SUFFIX>  
28  
QuickScan® L  
Global Prefix/Suffix  
Global Prefix/Suffix — continued  
<PREFIX> <DATA>  
<PREFIX> <DATA> <SUFFIX>  
Enter  
Data Format Cancel  
Product Reference Guide  
29  
General Features  
FN1 Substitution Values  
The Wedge and USB HID Keyboard hosts support an FN1 substitution feature. When  
enabled, any FN1 character (0x1b) in an EAN128 bar code is substituted with a value.  
This value defaults to 7013 (Enter Key).  
To select an FN1 substitution value via bar code menus:  
1. Scan the bar code below.  
*Set FN1 Substitution Value  
2. Look up the keystroke desired for FN1 Substitution inAppendix F, ASCII Character  
Sets for the currently installed host interface.  
3. Enter the 4-digit substitution value by scanning each digit in Appendix E, Keypad.  
To correct an error or change the selection, scan Cancel.  
To enable FN1 substitution for keyboard wedge, scan the Enable FN1 Substitution  
on page 63.  
To enable FN1 Substitution for USB HID keyboard, scan the Enable FN1 Substitu-  
tion on page 82.  
Transmit “No Read” Message  
Scan a bar code below to select whether or not to transmit a No Read message. When  
enabled, the characters NR are transmitted when a bar code is not decoded. When dis-  
abled, if a bar code does not decode, nothing is sent to the host.  
Enable No Read  
*Disable No Read  
30  
QuickScan® L  
Chapter 6  
RS-232  
Introduction  
This chapter describes how to set up the scanner with an RS-232 host. The RS-232 in-  
terface is used to connect the scanner to point-of-sale devices, host computers, or other  
devices with an available RS-232 port (e.g., com port).  
If the host is not listed in Table 6, refer to the documentation for the host device to set  
communication parameters to match the host.  
The scanner uses TTL RS-232 signal levels, which will interface with most  
system architectures.  
NOTE  
Throughout the programming bar code menus, default values are indicated with asterisks  
(*).  
*Baud Rate 57,600  
Feature/Option  
* Indicates Default  
Product Reference Guide  
31  
RS-232  
Connecting an RS-232 Interface  
This connection is made directly from the scanner to the host computer.  
Figure 8. RS-232 Direct Connection  
Interface Cable  
Serial Port  
Connector  
to Host  
Power  
Supply Cable  
Interface cables vary depending on configuration. The connectors illustrated  
in Figure 8 are examples only. The connectors may be different than those  
illustrated, but the steps to connect the scanner remain the same.  
NOTE  
1. Attach the modular connector of the RS-232 interface cable to the cable interface port on  
the scanner (see Installing the Interface Cable on page 6).  
2. Connect the other end of the RS-232 interface cable to the serial port on the host.  
1
3. Connect the power supply to the serial connector end of the RS-232 interface cable. Plug  
the power supply into an appropriate outlet.  
4. Select the RS-232 host type by scanning the appropriate bar code from RS-232 Host  
Types on page 36.  
5. To modify any other parameter options, scan the appropriate bar codes in this chapter.  
Refer to RS-232 Host Commands on page 179 for a listing of host  
commands the scanner will respond to when in RS-232 interface mode.  
NOTE  
1. Use only aDatalogic power supply approved for this product.  
32  
QuickScan® L  
RS-232 Parameter Defaults  
RS-232 Parameter Defaults  
Table 5 lists the defaults for RS-232 host parameters. If any option needs to be changed,  
scan the appropriate bar code(s) provided in the Parameter Descriptions section begin-  
ning on page 33.  
See Appendix B, Standard Defaults for all user preferences, hosts, symbolo-  
gies, and miscellaneous default parameters.  
NOTE  
Table 5. RS-232 Defaults  
Parameter  
RS-232 Host Parameters  
Default  
Page Number  
RS-232 Host Types  
Baud Rate  
Standard  
9600  
36  
37  
38  
39  
39  
40  
42  
44  
45  
46  
46  
47  
48  
48  
Parity Type  
None  
Stop Bit Select  
1 Stop Bit  
8-Bit  
Data Bits (ASCII Format)  
Check Receive Errors  
Hardware Handshaking  
Software Handshaking  
Host Serial Response Time-out  
RTS Line State  
Enable  
None  
None  
2 Sec  
Low RTS  
Disable  
0 msec  
Beep on <BEL>  
Intercharacter Delay  
Nixdorf Beep/LED Options  
Ignore Unknown Characters  
Normal Operation  
Send Bar Code  
RS-232 Host Parameters  
Various RS-232 hosts are set up with their own parameter default settings (Table 6). Se-  
lecting the ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, Olivetti,  
Omron, or terminal sets the defaults listed in Table 6.  
Selecting the ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, OPOS  
terminal enables the transmission of code ID characters listed in Table 7 on page 34.  
These code ID characters are not programmable and are separate from the Transmit  
Code ID feature. The Transmit Code ID feature should not be enabled for these termi-  
nals.  
Product Reference Guide  
33  
RS-232  
Table 6. Terminal Specific RS-232  
Wincor-  
Nixdorf  
Mode B/  
OPOS  
Wincor-  
Nixdorf  
Mode A  
Standard  
(Default)  
Parameter  
ICL  
Fujitsu  
Olivetti  
Omron  
Transmit  
Code ID  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Data Transmis-  
sion Format  
Prefix/Data/Suf-  
fix  
Data as is  
Data/Suffix Data/Suffix  
Data/Suffix  
CR (1013)  
Data/Suffix  
CR (1013)  
Data/Suffix  
CR (1013)  
CR/LF  
(7013)  
Suffix  
CR (1013)  
CR (1013)  
ETX (1002)  
Baud Rate  
Parity  
9600  
None  
9600  
Even  
9600  
None  
9600  
Odd  
9600  
Odd  
9600  
Even  
9600  
None  
Hardware Hand-  
shaking  
RTS/CTS  
Option 3  
RTS/CTS  
Option 3  
RTS/CTS  
Option 3  
None  
None  
2 Sec.  
None  
None  
2 Sec.  
None  
None  
None  
Software Hand-  
shaking  
None  
None  
None  
Ack/Nak  
9.9 Sec.  
Serial Response  
Time-out  
9.9 Sec.  
9.9 Sec.  
9.9 Sec.  
9.9 Sec.  
Stop Bit  
Select  
One  
8-Bit  
One  
8-Bit  
One  
8-Bit  
One  
8-Bit  
One  
8-Bit  
One  
7-Bit  
One  
8-Bit  
ASCII Format  
Beep On  
<BEL>  
Disable  
Disable  
Disable  
Disable  
Disable  
Disable  
Disable  
RTS Line  
State  
Low = No data  
to send  
Low  
High  
Low  
Low  
Low  
High  
Prefix  
None  
None  
None  
None  
None  
STX (1003)  
None  
*In the Nixdorf Mode B, if CTS is Low, scanning is disabled. When CTS is High, the user can scan bar codes.  
**If Nixdorf Mode B is scanned without the scanner connected to the proper host, it may appear unable to scan. If this happens, scan a  
different RS-232 host type within 5 seconds of cycling power to the scanner.  
Table 7. Terminal Specific Code ID Characters  
Wincor-  
Nixdorf  
Mode A  
Wincor-  
Nixdorf  
Mode B/OPOS  
ICL  
Fujitsu  
Olivetti  
Omron  
UPC-A  
UPC-E  
A
E
A
E
A
C
B
A
C
B
A
C
B
A
E
EAN-8/JAN-8  
FF  
FF  
FF  
34  
QuickScan® L  
RS-232 Host Parameters  
Table 7. Terminal Specific Code ID Characters  
Wincor-  
Nixdorf  
Mode A  
Wincor-  
Nixdorf  
Mode B/OPOS  
ICL  
Fujitsu  
Olivetti  
Omron  
EAN-13/JAN-13  
Code 39  
Codabar  
Code 128  
I 2 of 5  
F
F
A
A
A
F
C <len>  
N <len>  
L <len>  
I <len>  
None  
None  
None  
None  
None  
None  
None  
None  
None  
F
M
M
M <len>  
N <len>  
K <len>  
I <len>  
L <len>  
H <len>  
P <len>  
O <len>  
A
C <len>  
N <len>  
L <len>  
I <len>  
None  
N
N
K
K
I
L
I
L
Code 93  
D 2 of 5  
H <len>  
L <len>  
None  
H
H
H <len>  
L <len>  
None  
UCC/EAN 128  
MSI  
P
P
O
O
Bookland EAN  
Trioptic  
F
A
A
F
None  
None  
None  
None  
None  
None  
None  
H
None  
None  
H
None  
None  
Code 11  
IATA  
None  
None  
None  
H<len>  
None  
None  
None  
Code 32  
None  
None  
None  
None  
Product Reference Guide  
35  
RS-232  
RS-232 Host Types  
To select an RS-232 host interface, scan one of the following bar codes.  
*Standard RS-232  
ICL RS-232  
RS-232 Wincor-Nixdorf Mode A  
RS-232 Wincor-Nixdorf Mode B  
RS-232 Olivetti ORS4500  
RS-232 Omron  
RS-232 OPOS  
RS-232 Fujitsu  
36  
QuickScan® L  
RS-232 Host Parameters  
Baud Rate  
Baud rate is the number of bits of data transmitted per second. Set the scanner's baud  
rate to match the baud rate setting of the host device. Otherwise, data may not reach the  
host device or may reach it in distorted form.  
Baud Rate 600  
Baud Rate 1200  
Baud Rate 2400  
Baud Rate 4800  
*Baud Rate 9600  
Baud Rate 19,200  
Baud Rate 38,400  
Product Reference Guide  
37  
RS-232  
Parity  
A parity check bit is the most significant bit of each ASCII coded character. Select the  
parity type according to host device requirements.  
Select Odd parity and the parity bit value is set to 0 or 1, based on data, to ensure that an  
odd number of 1 bits are contained in the coded character.  
Select Even parity and the parity bit value is set to 0 or 1, based on data, to ensure that an  
even number of 1 bits are contained in the coded character.  
Select Mark parity and the parity bit is always 1.  
Select Space parity and the parity bit is always 0.  
Select None when no parity bit is required.  
Odd  
Even  
Mark  
Space  
*None  
38  
QuickScan® L  
RS-232 Host Parameters  
Stop Bit Select  
The stop bit(s) at the end of each transmitted character marks the end of transmission of  
one character and prepares the receiving device for the next character in the serial data  
stream. The number of stop bits selected (one or two) depends on the number the receiv-  
ing terminal is programmed to accommodate. Set the number of stop bits to match host  
device requirements.  
*1 Stop Bit  
2 Stop Bits  
Data Bits (ASCII Format)  
This parameter allows the scanner to interface with devices requiring a 7-bit or 8-bit  
ASCII protocol.  
7-Bit  
*8-Bit  
Product Reference Guide  
39  
RS-232  
Check Receive Errors  
Select whether or not the parity, framing, and overrun of received characters are checked.  
The parity value of received characters is verified against the parity parameter selected  
above.  
*Check For Received Errors  
(Enable)  
Do Not Check For Received Errors  
(Disable)  
40  
QuickScan® L  
RS-232 Host Parameters  
Hardware Handshaking  
The data interface consists of an RS-232 port designed to operate either with or without  
the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS).  
If Standard RTS/CTS handshaking is not selected, scan data is transmitted as it becomes  
available. If Standard RTS/CTS handshaking is selected, scan data is transmitted accord-  
ing to the following sequence:  
The scanner reads the CTS line for activity. If CTS is asserted, the scanner waits up to  
Host Serial Response Time-out for the host to de-assert the CTS line. If, after Host Serial  
Response Time-out, the CTS line is still asserted, the scanner sounds a transmit error, and  
any scanned data is lost.  
When the CTS line is de-asserted, the scanner asserts the RTS line and waits up to Host  
Serial Response Time-out for the host to assert CTS. When the host asserts CTS, data is  
transmitted. If, after Host Serial Response Time-out, the CTS line is not asserted, the  
scanner sounds a transmit error, and discards the data.  
When data transmission is complete, the scanner de-asserts RTS 10 msec after sending the  
last character.  
The host should respond by negating CTS. The scanner checks for a de-asserted CTS  
upon the next transmission of data.  
During the transmission of data, the CTS line should be asserted. If CTS is de-asserted  
for more than 50 ms between characters, the transmission is aborted, the scanner sounds  
a transmission error, and the data is discarded.  
If the above communication sequence fails, the scanner issues an error indication. In this  
case, the data is lost and must be rescanned.  
If Hardware Handshaking and Software Handshaking are both enabled, Hardware  
Handshaking takes precedence.  
The DTR signal is jumpered to the active state.  
NOTE  
None: Scan the bar code below if no Hardware Handshaking is desired.  
Standard RTS/CTS: Scan the bar code below to select Standard RTS/CTS Hardware  
Handshaking.  
RTS/CTS Option 1: When RTS/CTS Option 1 is selected, the scanner asserts RTS  
before transmitting and ignores the state of CTS. The scanner de-asserts RTS when the  
transmission is complete.  
RTS/CTS Option 2: When Option 2 is selected, RTS is always high or low (user-pro-  
grammed logic level). However, the scanner waits for CTS to be asserted before transmit-  
ting data. If CTS is not asserted within Host Serial Response Time-out, the scanner issues  
an error indication and discards the data.  
Product Reference Guide  
41  
RS-232  
Hardware Handshaking — cont.  
RTS/CTS Option 3: When Option 3 is selected, the scanner asserts RTS prior to any data  
transmission, regardless of the state of CTS. The scanner waits up to Host Serial Response  
Time-out for CTS to be asserted. If CTS is not asserted during this time, the scanner  
issues an error indication and discards the data. The scanner de-asserts RTS when trans-  
mission is complete.  
*None  
Standard RTS/CTS  
RTS/CTS Option 1  
RTS/CTS Option 2  
RTS/CTS Option 3  
42  
QuickScan® L  
RS-232 Host Parameters  
Software Handshaking  
This parameter offers control of the data transmission process in addition to, or instead  
of, that offered by hardware handshaking. There are five options.  
If Software Handshaking and Hardware Handshaking are both enabled, Hardware  
Handshaking takes precedence.  
None: When this option is selected, data is transmitted immediately. No response is  
expected from host.  
ACK/NAK: When this option is selected, after transmitting data, the scanner expects  
either an ACK or NAK response from the host. When a NAK is received, the scanner  
transmits the same data again and waits for either an ACK or NAK. After three unsuccess-  
ful attempts to send data when NAKs are received, the scanner issues an error indication  
and discards the data.  
The scanner waits up to the programmable Host Serial Response Time-out to receive an  
ACK or NAK. If the scanner does not get a response in this time, it issues an error indica-  
tion and discards the data. There are no retries when a time-out occurs.  
ENQ: When this option is selected, the scanner waits for an ENQ character from the host  
before transmitting data. If an ENQ is not received within the Host Serial Response  
Time-out, the scanner issues an error indication and discards the data. The host must  
transmit an ENQ character at least every Host Serial Response Time-out to prevent trans-  
mission errors.  
ACK/NAK with ENQ: This combines the two previous options. For re-transmissions of  
data, due to a NAK from the host, an additional ENQ is not required.  
XON/XOFF: An XOFF character turns the scanner transmission off until the scanner  
receives an XON character. There are two situations for XON/XOFF:  
- XOFF is received before the scanner has data to send. When the scanner has data to  
send, it waits up to Host Serial Response Time-out for an XON character before trans-  
mission. If the XON is not received within this time, the scanner issues an error indica-  
tion and discards the data.  
- XOFF is received during a transmission. Data transmission then stops after sending the  
current byte. When the scanner receives an XON character, it sends the rest of the data  
message. The scanner waits up to 30 seconds for the XON.  
Product Reference Guide  
43  
RS-232  
Software Handshaking — cont.  
*None  
ACK/NAK  
ENQ  
ACK/NAK with ENQ  
XON/XOFF  
44  
QuickScan® L  
RS-232 Host Parameters  
Host Serial Response Time-out  
This parameter specifies how long the scanner waits for an ACK, NAK, ENQ, XON, or  
CTS before determining that a transmission error occurred.  
*Minimum: 2 Sec  
Low: 2.5 Sec  
Medium: 5 Sec  
High: 7.5 Sec  
Maximum: 9.9 Sec  
Product Reference Guide  
45  
RS-232  
RTS Line State  
This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to  
select Low RTS or High RTS line state.  
*Host: Low RTS  
Host: High RTS  
Beep on <BEL>  
When this parameter is enabled, the scanner issues a beep when a <BEL> character is de-  
tected on the RS-232 serial line. <BEL> is issued to gain a user's attention to an illegal  
entry or other important event.  
Beep On <BEL> Character  
(Enable)  
*Do Not Beep On <BEL> Character  
(Disable)  
46  
QuickScan® L  
RS-232 Host Parameters  
Intercharacter Delay  
This parameter specifies the intercharacter delay inserted between character transmis-  
sions.  
*Minimum: 0 msec  
Low: 25 msec  
Medium: 50 msec  
High: 75 msec  
Maximum: 99 msec  
Product Reference Guide  
47  
RS-232  
Nixdorf Beep/LED Options  
When Nixdorf Mode B is selected, this indicates when the scanner should beep and turn  
on its LED after a decode.  
*Normal Operation  
(Beep/LED immediately after decode)  
Beep/LED After Transmission  
Beep/LED After CTS Pulse  
Ignore Unknown Characters  
Unknown characters are characters the host does not recognize. When Send Bar Codes  
with Unknown Characters is selected, all bar code data is sent except for unknown char-  
acters, and no error beeps sound on the scanner. When Do Not Send Bar Codes With  
Unknown Characters is selected, bar code data is sent up to the first unknown character  
and then an error beep sounds on the scanner.  
*Send Bar Code with Unknown Characters  
Do Not Send Bar Codes with Unknown Characters  
48  
QuickScan® L  
ASCII Character Set for RS-232  
ASCII Character Set for RS-232  
The values in Table 8 can be assigned as prefixes or suffixes for ASCII character data  
transmission.  
Table 8. ASCII Character Set for RS-232  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
ASCII Character  
1000  
1001  
1002  
1003  
1004  
1005  
1006  
1007  
1008  
1009  
1010  
1011  
1012  
1013  
1014  
1015  
1016  
1017  
1018  
1019  
1020  
1021  
1022  
1023  
1024  
1025  
1026  
%U  
$A  
$B  
$C  
$D  
$E  
$F  
$G  
$H  
$I  
NUL  
SOH  
STX  
ETX  
EOT  
ENQ  
ACK  
BELL  
BCKSPC  
HORIZ TAB  
LF/NW LN  
VT  
$J  
$K  
$L  
FF  
$M  
$N  
$O  
$P  
$Q  
$R  
$S  
$T  
$U  
$V  
$W  
$X  
$Y  
$Z  
CR/ENTER  
SO  
SI  
DLE  
DC1/XON  
DC2  
DC3/XOFF  
DC4  
NAK  
SYN  
ETB  
CAN  
EM  
SUB  
Product Reference Guide  
49  
RS-232  
Table 8. ASCII Character Set for RS-232 (Continued)  
Full ASCII  
ASCII Value  
ASCII Character  
Code 39 Encode Character  
1027  
1028  
1029  
1030  
1031  
1032  
1033  
1034  
1035  
1036  
1037  
1038  
1039  
1040  
1041  
1042  
1043  
1044  
1045  
1046  
1047  
1048  
1049  
1050  
1051  
1052  
1053  
1054  
1057  
1056  
%A  
%B  
%C  
%D  
%E  
Space  
/A  
/B  
/C  
/D  
/E  
/F  
/G  
/H  
/I  
ESC  
FS  
GS  
RS  
US  
Space  
!
"
#
$
%
&
(
)
/J  
*
/K  
/L  
+
,
-
-
.
.
/O  
0
/
0
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
50  
QuickScan® L  
ASCII Character Set for RS-232  
Table 8. ASCII Character Set for RS-232 (Continued)  
Full ASCII  
ASCII Value  
ASCII Character  
Code 39 Encode Character  
1057  
1058  
1059  
1060  
1061  
1062  
1063  
1064  
1065  
1066  
1067  
1068  
1069  
1070  
1071  
1072  
1073  
1074  
1075  
1076  
1077  
1078  
1079  
1080  
1081  
1082  
1083  
1084  
1085  
1086  
9
/Z  
%F  
%G  
%H  
%I  
%J  
%V  
A
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
B
C
D
E
F
G
H
I
J
J
K
K
L
L
M
N
M
N
O
P
Q
R
S
T
U
V
O
P
Q
R
S
T
U
V
Product Reference Guide  
51  
RS-232  
Table 8. ASCII Character Set for RS-232 (Continued)  
Full ASCII  
ASCII Value  
ASCII Character  
Code 39 Encode Character  
1087  
1088  
1089  
1090  
1091  
1092  
1093  
1094  
1095  
1096  
1097  
1098  
1099  
1100  
1101  
1102  
1103  
1104  
1105  
1106  
1107  
1108  
1109  
1110  
1111  
1112  
1113  
1114  
1115  
1116  
W
X
W
X
Y
Z
[
Y
Z
%K  
%L  
%M  
%N  
%O  
%W  
+A  
+B  
+C  
+D  
+E  
+F  
+G  
+H  
+I  
\
]
^
_
`
a
b
c
d
e
f
g
h
i
+J  
j
+K  
+L  
k
l
+M  
+N  
+O  
+P  
+Q  
+R  
+S  
+T  
m
n
o
p
q
r
s
t
52  
QuickScan® L  
ASCII Character Set for RS-232  
Table 8. ASCII Character Set for RS-232 (Continued)  
Full ASCII  
ASCII Value  
ASCII Character  
Code 39 Encode Character  
1117  
1118  
1119  
1120  
1121  
1122  
1123  
1124  
1125  
1126  
1127  
7013  
+U  
+V  
u
v
+W  
+X  
w
x
+Y  
y
+Z  
z
%P  
%Q  
%R  
%S  
{
|
}
~
Undefined  
ENTER  
Product Reference Guide  
53  
RS-232  
NOTES  
54  
QuickScan® L  
Chapter 7  
Keyboard Wedge Interface  
This chapter describes how to set up a Keyboard Wedge interface with the scanner. With  
this interface, the scanner is connected between the keyboard and host computer, and  
translates bar code data into keystrokes. The host computer accepts the keystrokes as if  
they originated from the keyboard. This mode adds bar code reading functionality to a  
system designed for manual keyboard input. Keyboard keystrokes are simply passed  
through.  
Throughout the programming bar code menus, default values are indicated with asterisks  
(*).  
Feature/Option  
* Indicates Default  
*North American  
Connecting a Keyboard Wedge Interface  
Figure 9. Keyboard Wedge Connection with Y-cable  
Male DIN Connector  
Keyboard  
Connector  
Female DIN  
Connector  
Product Reference Guide  
55  
Keyboard Wedge Interface  
To connect the Keyboard Wedge interface Y-cable:  
Interface cables vary depending on configuration. The connectors illustrated  
in Figure 1 are examples only. The connectors may be different than those  
illustrated, but the steps to connect the scanner remain the same.  
NOTE  
1. Turn off the host and unplug the keyboard connector.  
2. Attach the modular connector of the Y-cable to the cable interface port on the scanner.  
(See Installing the Interface Cable on page 6.)  
3. Connect the round male DIN host connector of the Y-cable to the keyboard port on the  
host device.  
4. Connect the round female DIN keyboard connector of the Y-cable to the keyboard con-  
nector.  
5. If needed, attach the optional power supply to the connector in the middle of the Y-cable.  
6. Ensure that all connections are secure.  
7. Turn on the host system.  
8. Select the Keyboard Wedge host type by scanning the appropriate bar code from Key-  
board Wedge Host Parameters on page 57.  
9. To modify any other parameter options, scan the appropriate bar codes in this chapter.  
Keyboard Wedge Parameter Defaults  
See Appendix B, Standard Defaults for all user preferences, hosts, symbolo-  
gies, and miscellaneous default parameters.  
NOTE  
Table 9 lists the defaults for Keyboard Wedge host parameters. To change any option,  
scan the appropriate bar code(s) in the Keyboard Wedge Host Parameters section begin-  
ning on page 57.  
Table 9. Keyboard Wedge Defaults  
Parameter  
Default  
Page Number  
Keyboard Wedge Host Parameters  
IBM PC/AT& IBM PC Compatibles1  
Keyboard Wedge Host Type  
Country Types (Country Codes)  
Ignore Unknown Characters  
Keystroke Delay  
57  
58  
59  
60  
60  
North American  
Send  
No Delay  
Disable  
Intra-Keystroke Delay  
56  
QuickScan® L  
Keyboard Wedge Host Parameters  
Table 9. Keyboard Wedge Defaults (Continued)  
Parameter  
Default  
Page Number  
Alternate Numeric Keypad Emulation  
Caps Lock On  
Disable  
Disable  
Disable  
No Convert  
Disable  
Disable  
Send  
61  
61  
62  
62  
63  
63  
63  
Caps Lock Override  
Convert Wedge Data  
Function Key Mapping  
FN1 Substitution  
Send and Make Break  
1User selection is required to configure this interface and this is the most common selection.  
Keyboard Wedge Host Parameters  
Keyboard Wedge Host Types  
Select the Keyboard Wedge host by scanning one of the bar codes below.  
User selection is required to configure this interface and this is the most  
common selection.  
NOTE  
1
IBM PC/AT & IBM PC Compatibles  
IBM AT Notebook  
NCR 7052  
IBM PS/2 (Model 30)  
Product Reference Guide  
57  
Keyboard Wedge Interface  
Keyboard Wedge Country Types (Country Codes)  
Scan the bar code corresponding to the keyboard type. If the keyboard type is not listed,  
see Alternate Numeric Keypad Emulation on page 61.  
*North American  
German Windows  
French Windows  
French Canadian Windows 95/98  
French Canadian Windows XP/2000  
Spanish Windows  
Italian Windows  
58  
QuickScan® L  
Keyboard Wedge Host Parameters  
Keyboard Wedge Country Types (continued)  
Swedish Windows  
UK English Windows  
Japanese Windows  
Portuguese-Brazilian Windows  
Ignore Unknown Characters  
Unknown characters are characters the host does not recognize. When Send Bar Codes  
With Unknown Characters is selected, all bar code data is sent except for unknown char-  
acters, and no error beeps sound on the scanner. When Do Not Send Bar Codes With  
Unknown Characters is selected, bar code data is sent up to the first unknown character,  
then the scanner issues an error beep.  
*Send Bar Codes with Unknown Characters  
Do Not Send Bar Codes with Unknown Characters  
Product Reference Guide  
59  
Keyboard Wedge Interface  
Keystroke Delay  
This is the delay in milliseconds between emulated keystrokes. Scan a bar code below to  
increase the delay when hosts require a slower transmission of data.  
*No Delay  
Medium Delay (20 msec)  
Long Delay (40 msec)  
Intra-Keystroke Delay  
When enabled, an additional delay is inserted between each emulated key depression and  
release. This sets the Keystroke Delay parameter to a minimum of 5 msec as well.  
Enable Intra-Keystroke Delay  
*Disable Intra-Keystroke Delay  
60  
QuickScan® L  
Keyboard Wedge Host Parameters  
Alternate Numeric Keypad Emulation  
This allows emulation of most other country keyboard types not listed in Keyboard  
®
Wedge Country Types (Country Codes) on page 58 in a Microsoft operating system  
environment.  
Enable Alternate Numeric Keypad  
*Disable Alternate Numeric Keypad  
Caps Lock On  
When enabled, the scanner emulates keystrokes as if the Caps Lock key is always pressed.  
Note that if both Caps Lock On and Caps Lock Override are enabled, Caps Lock Over-  
ride takes precedence  
Enable Caps Lock On  
*Disable Caps Lock On  
Product Reference Guide  
61  
Keyboard Wedge Interface  
Caps Lock Override  
When enabled, on AT or AT Notebook hosts, the keyboard ignores the state of the Caps  
Lock key. Therefore, an ‘A’ in the bar code is sent as an ‘A’ no matter what the state of  
the keyboard’s Caps Lock key.  
If both Caps Lock On and Caps Lock Override are enabled, Caps Lock Over-  
ride takes precedence.  
NOTE  
Enable Caps Lock Override  
*Disable Caps Lock Override  
Convert Wedge Data  
When enabled, the scanner will convert all bar code data to the selected case.  
Convert to Upper Case  
Convert to Lower Case  
*No Convert  
62  
QuickScan® L  
Keyboard Wedge Host Parameters  
Function Key Mapping  
ASCII values under 32 are normally sent as control key sequences (see Table 10 on page  
64). When this parameter is enabled, the keys in bold are sent in place of the standard  
key mapping. Table entries that do not have a bold entry remain the same whether or  
not this parameter is enabled.  
Enable Function Key Mapping  
*Disable Function Key Mapping  
FN1 Substitution  
When enabled, the scanner replaces FN1 characters in an EAN128 bar code with a key-  
stroke chosen by the user (see FN1 Substitution Values on page 30).  
Enable FN1 Substitution  
*Disable FN1 Substitution  
Send Make and Break  
When enabled, the scan codes for releasing a key are not sent.  
*Send Make and Break Scan Codes  
Send Make Scan Code Only  
Product Reference Guide  
63  
Keyboard Wedge Interface  
Keyboard Maps  
The following keyboard maps are provided for prefix/suffix keystroke parameters. To  
program the prefix/suffix values, see the bar codes on page 27 through page 29.  
Figure 10. IBM PC/AT  
5001  
5003  
5005  
5007  
5009  
7008  
7013  
7014  
7012  
5002  
5004  
5006  
5008  
5010  
7009  
7003  
7004  
7011  
7002  
Figure 11. IBM PS/2  
ASCII Character Set for Keyboard Wedge  
Code 39 Full ASCII interprets the bar code special character ($ + % /) preced-  
ing a Code 39 character and assigns an ASCII character value to the pair. For  
example, when Code 39 Full ASCII is enabled and a +B is scanned, it is inter-  
preted as b, %J as ?, and %V as @. Scanning ABC%I outputs the keystroke  
equivalent of ABC >.  
NOTE  
Table 10. Keyboard Wedge ASCII Character Set  
Full ASCII  
ASCII Value  
Keystroke  
Code 39 Encode Character  
1001  
1002  
1003  
1004  
$A  
$B  
$C  
$D  
CTRL A  
CTRL B  
CTRL C  
CTRL D  
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
64  
QuickScan® L  
ASCII Character Set for Keyboard Wedge  
Table 10. Keyboard Wedge ASCII Character Set (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1005  
1006  
1007  
1008  
1009  
1010  
1011  
1012  
1013  
1014  
1015  
1016  
1017  
1018  
1019  
1020  
1021  
1022  
1023  
1024  
1025  
1026  
1027  
1028  
1029  
1030  
1031  
1032  
$E  
$F  
CTRL E  
CTRL F  
$G  
$H  
$I  
CTRL G  
CTRL H/BACKSPACE1  
CTRL I/HORIZONTAL TAB1  
CTRL J  
$J  
$K  
CTRL K  
$L  
CTRL L  
CTRL M/ENTER1  
CTRL N  
$M  
$N  
$O  
$P  
CTRL O  
CTRL P  
$Q  
$R  
$S  
CTRL Q  
CTRL R  
CTRL S  
$T  
CTRL T  
$U  
$V  
CTRL U  
CTRL V  
$W  
$X  
CTRL W  
CTRL X  
$Y  
CTRL Y  
$Z  
CTRL Z  
CTRL [ /ESC1  
CTRL \  
%A  
%B  
%C  
%D  
%E  
Space  
CTRL ]  
CTRL 6  
CTRL -  
Space  
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Product Reference Guide  
65  
Keyboard Wedge Interface  
Table 10. Keyboard Wedge ASCII Character Set (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1033  
1034  
1035  
1036  
1037  
1038  
1039  
1040  
1041  
1042  
1043  
1044  
1045  
1046  
1047  
1048  
1049  
1050  
1051  
1052  
1053  
1054  
1055  
1056  
1057  
1058  
1059  
1060  
/A  
/B  
/C  
/D  
/E  
/F  
/G  
/H  
/I  
!
#
$
%
&
(
)
/J  
/K  
/L  
-
*
+
,
-
.
.
/O  
0
/
0
1
2
3
4
5
6
7
8
9
:
1
2
3
4
5
6
7
8
9
/Z  
%F  
%G  
;
<
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
66  
QuickScan® L  
ASCII Character Set for Keyboard Wedge  
Table 10. Keyboard Wedge ASCII Character Set (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1061  
1062  
1063  
1064  
1065  
1066  
1067  
1068  
1069  
1070  
1071  
1072  
1073  
1074  
1075  
1076  
1077  
1078  
1079  
1080  
1081  
1082  
1083  
1084  
1085  
1086  
1087  
1088  
%H  
%I  
%J  
%V  
A
=
>
?
@
A
B
C
D
E
F
B
C
D
E
F
G
H
I
G
H
I
J
J
K
K
L
L
M
N
O
P
M
N
O
P
Q
R
S
T
Q
R
S
T
U
V
U
V
W
X
W
X
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Product Reference Guide  
67  
Keyboard Wedge Interface  
Table 10. Keyboard Wedge ASCII Character Set (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1089  
1090  
1091  
1092  
1093  
1094  
1095  
1096  
1097  
1098  
1099  
1100  
1101  
1102  
1103  
1104  
1105  
1106  
1107  
1108  
1109  
1110  
1111  
1112  
1113  
1114  
1115  
1116  
Y
Z
Y
Z
[
%K  
%L  
%M  
%N  
%O  
%W  
+A  
+B  
+C  
+D  
+E  
+F  
+G  
+H  
+I  
\
]
^
_
a
b
c
d
e
f
g
h
i
+J  
j
+K  
+L  
k
l
+M  
+N  
+O  
+P  
+Q  
+R  
+S  
+T  
m
n
o
p
q
r
s
t
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
68  
QuickScan® L  
ASCII Character Set for Keyboard Wedge  
Table 10. Keyboard Wedge ASCII Character Set (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1117  
1118  
1119  
1120  
1121  
1122  
1123  
1124  
1125  
1126  
+U  
+V  
u
v
w
x
y
z
{
+W  
+X  
+Y  
+Z  
%P  
%Q  
%R  
%S  
|
}
~
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Table 11. Keyboard Wedge ALT Key Character Set  
ALT Keys  
2065  
2066  
2067  
2068  
2069  
2070  
2071  
2072  
2073  
2074  
2075  
2076  
2077  
2078  
2079  
2080  
Keystroke  
ALT A  
ALT B  
ALT C  
ALT D  
ALT E  
ALT F  
ALT G  
ALT H  
ALT I  
ALT J  
ALT K  
ALT L  
ALT M  
ALT N  
ALT O  
ALT P  
Product Reference Guide  
69  
Keyboard Wedge Interface  
Table 11. Keyboard Wedge ALT Key Character Set (Continued)  
ALT Keys  
2081  
2082  
2083  
2084  
2085  
2086  
2087  
2088  
2089  
2090  
Keystroke  
ALT Q  
ALT R  
ALT S  
ALT T  
ALT U  
ALT V  
ALT W  
ALT X  
ALT Y  
ALT Z  
Table 12. Keyboard Wedge GIU Key Character Set  
GUI Keys  
3000  
3048  
3049  
3050  
3051  
3052  
3053  
3054  
3055  
3056  
3057  
3065  
3066  
3067  
3068  
3069  
3070  
3071  
3072  
Keystrokes  
Right Control Key  
GUI 0  
GUI 1  
GUI 2  
GUI 3  
GUI 4  
GUI 5  
GUI 6  
GUI 7  
GUI 8  
GUI 9  
GUI A  
GUI B  
GUI C  
GUI D  
GUI E  
GUI F  
GUI G  
GUI H  
70  
QuickScan® L  
ASCII Character Set for Keyboard Wedge  
Table 12. Keyboard Wedge GIU Key Character Set (Continued)  
GUI Keys  
3073  
3074  
3075  
3076  
3077  
3078  
3079  
3080  
3081  
3082  
3083  
3084  
3085  
3086  
3087  
3088  
3089  
3090  
Keystrokes  
GUI I  
GUI J  
GUI K  
GUI L  
GUI M  
GUI N  
GUI O  
GUI P  
GUI Q  
GUI R  
GUI S  
GUI T  
GUI U  
GUI V  
GUI W  
GUI X  
GUI Y  
GUI Z  
Table 13. Keyboard Wedge F Key Character Set  
F Keys  
5001  
5002  
5003  
5004  
5005  
5006  
5007  
5008  
5009  
Keystroke  
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
Product Reference Guide  
71  
Keyboard Wedge Interface  
Table 13. Keyboard Wedge F Key Character Set (Continued)  
F Keys  
5010  
5011  
5012  
5013  
5014  
5015  
5016  
5017  
5018  
5019  
5020  
5021  
5022  
5023  
5024  
Keystroke  
F10  
F11  
F12  
F13  
F14  
F15  
F16  
F17  
F18  
F19  
F20  
F21  
F22  
F23  
F24  
Table 14. Keyboard Wedge Numeric Keypad Character Set  
Numeric Keypad  
6042  
Keystroke  
*
6043  
+
6044  
undefined  
6045  
-
.
6046  
6047  
/
6048  
0
1
2
3
4
5
6049  
6050  
6051  
6052  
6053  
72  
QuickScan® L  
ASCII Character Set for Keyboard Wedge  
Table 14. Keyboard Wedge Numeric Keypad Character Set (Continued)  
Numeric Keypad  
Keystroke  
6054  
6055  
6056  
6057  
6058  
6059  
6
7
8
9
Enter  
Num Lock  
Table 15. Keyboard Wedge Extended Keypad Character Set  
Extended Keypad  
7001  
Keystroke  
Break  
7002  
Delete  
7003  
Pg Up  
7004  
End  
7005  
Pg Dn  
7006  
Pause  
7007  
Scroll Lock  
Backspace  
Tab  
7008  
7009  
7010  
Print Screen  
Insert  
7011  
7012  
Home  
7013  
Enter  
7014  
Escape  
Up Arrow  
Dn Arrow  
Left Arrow  
Right Arrow  
7015  
7016  
7017  
7018  
Product Reference Guide  
73  
Keyboard Wedge Interface  
NOTES  
74  
QuickScan® L  
Chapter 8  
USB Interface  
This chapter covers the connection and setup of the scanner to a USB host. The scanner  
attaches directly to a USB host, or a powered USB hub, and is powered by it. No addi-  
tional power supply is required.  
Throughout the programming bar code menus, default values are indicated with asterisks  
(*).  
* Indicates Default  
Feature/Option  
*North American Standard USB Keyboard  
Connecting a USB Interface  
Figure 12. USB Connection  
Interface cable  
USB Series A  
Connector  
The scanner connects with USB capable hosts including:  
Desktop PCs and Notebooks  
Apple™ iMac, G4, iBooks (North America only)  
IBM SurePOS terminals  
Product Reference Guide  
75  
USB Interface  
Sun, IBM, and other network computers that support more than one keyboard.  
The following operating systems support the scanner through USB:  
Windows 98, 2000, ME, XP  
MacOS 8.5 and above  
IBM 4690 OS.  
The scanner will also interface with other USB hosts which support USB Human Inter-  
face Devices (HID). For more information on USB technology, hosts, and peripheral de-  
vices, visit the website listed on the back cover of this manual.  
Interface cables vary depending on configuration. The connectors illustrated  
in Figure 12 are examples only. The connectors may be different than those  
illustrated, but the steps to connect the scanner remain the same.  
NOTE  
To set up the scanner:  
1. Attach the modular connector of the USB interface cable to the cable interface port on the  
scanner (see Installing the Interface Cable on page 6).  
2. Plug the series A connector in the USB host or hub, or plug the Plus Power connector in  
an available port of the IBM SurePOS terminal.  
3. Select the USB device type by scanning the appropriate bar code from USB Device  
Type on page 77.  
4. On first installation when using Windows, the software prompts to select or install the  
Human Interface Device driver. To install this driver, provided by Windows, click Next  
through all the choices and click Finished on the last choice. The scanner powers up dur-  
ing this installation.  
5. To modify any other parameter options, scan the appropriate bar codes in this chapter.  
6. If problems occur with the system, see Table 3.  
USB Parameter Defaults  
Table 16 lists the defaults for USB host parameters. If any option needs to be changed,  
scan the appropriate bar code(s) provided in the Parameter Descriptions section begin-  
ning on page 77.  
See Appendix B, Standard Defaults for all user preferences, hosts, symbolo-  
gies, and miscellaneous default parameters.  
NOTE  
76  
QuickScan® L  
USB Host Parameters  
Table 16. USB Defaults  
Parameter  
Default  
Page Number  
USB Host Parameters  
USB Device Type  
HID Keyboard Emulation  
North American  
No Delay  
77  
78  
80  
80  
81  
81  
82  
82  
83  
83  
USB Country Keyboard Types (Country Codes)  
USB Keystroke Delay  
USB CAPS Lock Override  
USB Ignore Unknown Characters  
Emulate Keypad  
Disable  
Send  
Disable  
USB FN1 Substitution  
Function Key Mapping  
Simulated Caps Lock  
Disable  
Disable  
Disable  
Convert Case  
No Case Conversion  
USB Host Parameters  
USB Device Type  
Select the desired USB device type.  
When changing USB Device Types, the scanner automatically restarts. The  
scanner issues the standard startup beep sequences.  
NOTE  
*USB Keyboard  
USB OEM Table Top  
Product Reference Guide  
77  
USB Interface  
USB Device Type — continued  
USB OEM Handheld  
For USB OPOS operation, use host type OEM USB and an appropriate driver  
supplied by Datalogic.  
NOTE  
USB Country Keyboard Types (Country Codes)  
Scan the bar code corresponding to the keyboard type. This setting applies only to the  
USB HID Keyboard Emulation device.  
When changing USB country keyboard types the scanner automatically  
resets. The scanner issues the standard startup beep sequences.  
NOTE  
*North American Standard USB Keyboard  
German Windows  
French Windows  
French Canadian Windows 95/98  
78  
QuickScan® L  
USB Host Parameters  
USB Country Keyboard Types (Country Codes continued)  
French Canadian Windows 2000/XP  
Spanish Windows  
Italian Windows  
Swedish Windows  
UK English Windows  
Japanese Windows (ASCII)  
Portuguese-Brazilian Windows  
Product Reference Guide  
79  
USB Interface  
USB Keystroke Delay  
This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan a bar  
code below to increase the delay when hosts require a slower transmission of data.  
*No Delay  
Medium Delay (20 msec)  
Long Delay (40 msec)  
USB CAPS Lock Override  
This option applies only to the HID Keyboard Emulation device. When enabled, the  
case of the data is preserved regardless of the state of the caps lock key. This setting is  
always enabled for the “Japanese, Windows (ASCII)” keyboard type and cannot be dis-  
abled.  
Override Caps Lock Key  
(Enable)  
*Do Not Override Caps Lock Key  
(Disable)  
80  
QuickScan® L  
USB Host Parameters  
USB Ignore Unknown Characters  
This option applies only to the HID Keyboard Emulation device and IBM device. Un-  
known characters are characters the host does not recognize. When Send Bar Codes With  
Unknown Characters is selected, all bar code data is sent except for unknown characters,  
and no error beeps sound. When Do Not Send Bar Codes With Unknown Characters is  
selected, bar code data is sent up to the first unknown character, then the scanner issues  
an error beep.  
*Send Bar Codes with Unknown Characters  
Do Not Send Bar Codes with Unknown Characters  
Emulate Keypad  
When enabled, all characters are sent as ASCII sequences over the numeric keypad. For  
example ASCII A would be sent as “ALT make” 0 6 5 “ALT Break.”  
*Disable Keypad Emulation  
Enable Keypad Emulation  
Product Reference Guide  
81  
USB Interface  
USB Keyboard FN 1 Substitution  
This option applies only to the USB HID Keyboard Emulation device. When enabled,  
this allows replacement of any FN 1 characters in an EAN 128 bar code with a Key Cat-  
egory and value chosen by the user (see FN1 Substitution Values on page 30 to set the  
Key Category and Key Value).  
Enable FN1 Substitution  
*Disable FN1 Substitution  
Function Key Mapping  
ASCII values under 32 are normally sent as a control-key sequences (see Table 17 on  
page 84). When this parameter is enabled, the keys in bold are sent in place of the stan-  
dard key mapping. Table entries that do not have a bold entry remain the same whether  
or not this parameter is enabled.  
*Disable Function Key Mapping  
Enable Function Key Mapping  
82  
QuickScan® L  
USB Host Parameters  
Simulated Caps Lock  
When enabled, the scanner will invert upper and lower case characters on the scanner bar  
code as if the Caps Lock state is enabled on the keyboard. This inversion is done regard-  
less of the current state of the keyboard’s Caps Lock state.  
*Disable Simulated Caps Lock  
Enable Simulated Caps Lock  
Convert Case  
When enabled, the scanner will convert all bar code data to the selected case.  
*No Case Conversion  
Convert All to Upper Case  
Convert All to Lower Case  
Product Reference Guide  
83  
USB Interface  
ASCII Character Set for USB  
Table 17. ASCII Character Set for USB  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1000  
1001  
1002  
1003  
1004  
1005  
1006  
1007  
1008  
1009  
1010  
1011  
1012  
1013  
1014  
1015  
1016  
1017  
1018  
1019  
1020  
1021  
1022  
1023  
1024  
1025  
%U  
CTRL 2  
CTRL A  
$A  
$B  
$C  
$D  
$E  
$F  
$G  
$H  
$I  
CTRL B  
CTRL C  
CTRL D  
CTRL E  
CTRL F  
CTRL G  
CTRL H/BACKSPACE1  
CTRL I/HORIZONTAL TAB1  
CTRL J  
$J  
$K  
$L  
CTRL K  
CTRL L  
CTRL M/ENTER1  
CTRL N  
$M  
$N  
$O  
$P  
$Q  
$R  
$S  
$T  
$U  
$V  
$W  
$X  
$Y  
CTRL O  
CTRL P  
CTRL Q  
CTRL R  
CTRL S  
CTRL T  
CTRL U  
CTRL V  
CTRL W  
CTRL X  
CTRL Y  
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
84  
QuickScan® L  
ASCII Character Set for USB  
Table 17. ASCII Character Set for USB (Continued)  
Full ASCII  
ASCII Value  
Keystroke  
Code 39 Encode Character  
1026  
1027  
1028  
1029  
1030  
1031  
1032  
1033  
1034  
1035  
1036  
1037  
1038  
1039  
1040  
1041  
1042  
1043  
1044  
1045  
1046  
1047  
1048  
1049  
1050  
1051  
1052  
1053  
$Z  
%A  
%B  
%C  
%D  
%E  
Space  
/A  
/B  
/C  
/D  
/E  
/F  
CTRL Z  
CTRL [/ESC1  
CTRL \  
CTRL ]  
CTRL 6  
CTRL -  
Space  
!
#
$
%
&
/G  
/H  
/I  
(
)
/J  
*
/K  
/L  
+
,
-
-
.
.
/O  
0
/
0
1
2
3
4
5
1
2
3
4
5
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Product Reference Guide  
85  
USB Interface  
Table 17. ASCII Character Set for USB (Continued)  
Full ASCII  
ASCII Value  
Keystroke  
Code 39 Encode Character  
1054  
1055  
1056  
1057  
1058  
1059  
1060  
1061  
1062  
1063  
1064  
1065  
1066  
1067  
1068  
1069  
1070  
1071  
1072  
1073  
1074  
1075  
1076  
1077  
1078  
1079  
1080  
1081  
6
7
6
7
8
8
9
9
/Z  
%F  
%G  
%H  
%I  
%J  
%V  
A
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
B
C
D
E
F
G
H
I
J
J
K
K
L
L
M
N
M
N
O
P
Q
O
P
Q
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
86  
QuickScan® L  
ASCII Character Set for USB  
Table 17. ASCII Character Set for USB (Continued)  
Full ASCII  
ASCII Value  
Keystroke  
Code 39 Encode Character  
1082  
1083  
1084  
1085  
1086  
1087  
1088  
1089  
1090  
1091  
1092  
1093  
1094  
1095  
1096  
1097  
1098  
1099  
1100  
1101  
1102  
1103  
1104  
1105  
1106  
1107  
1108  
1109  
R
S
R
S
T
U
V
W
X
Y
Z
[
T
U
V
W
X
Y
Z
%K  
%L  
%M  
%N  
%O  
%W  
+A  
+B  
+C  
+D  
+E  
+F  
+G  
+H  
+I  
\
]
^
_
`
a
b
c
d
e
f
g
h
i
+J  
+K  
+L  
+M  
j
k
l
m
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Product Reference Guide  
87  
USB Interface  
Table 17. ASCII Character Set for USB (Continued)  
Full ASCII  
ASCII Value  
Keystroke  
Code 39 Encode Character  
1110  
1111  
1112  
1113  
1114  
1115  
1116  
1117  
1118  
1119  
1120  
1121  
1122  
1123  
1124  
1125  
1126  
+N  
+O  
+P  
+Q  
+R  
+S  
+T  
n
o
p
q
r
s
t
+U  
+V  
+W  
+X  
+Y  
+Z  
u
v
w
x
y
z
{
%P  
%Q  
%R  
%S  
|
}
~
1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Table 18. USB ALT Key Character Set  
ALT Keys  
2064  
Keystroke  
ALT 2  
2065  
ALT A  
ALT B  
ALT C  
ALT D  
ALT E  
ALT F  
2066  
2067  
2068  
2069  
2070  
88  
QuickScan® L  
ASCII Character Set for USB  
Table 18. USB ALT Key Character Set (Continued)  
ALT Keys  
2071  
2072  
2073  
2074  
2075  
2076  
2077  
2078  
2079  
2080  
2081  
2082  
2083  
2084  
2085  
2086  
2087  
2088  
2089  
2090  
Keystroke  
ALT G  
ALT H  
ALT I  
ALT J  
ALT K  
ALT L  
ALT M  
ALT N  
ALT O  
ALT P  
ALT Q  
ALT R  
ALT S  
ALT T  
ALT U  
ALT V  
ALT W  
ALT X  
ALT Y  
ALT Z  
Table 19. USB GUI Key Character Set  
GUI Key  
Keystroke  
3000  
3048  
3049  
3050  
3051  
3052  
Right Control Key  
GUI 0  
GUI 1  
GUI 2  
GUI 3  
GUI 4  
Note: GUI Shift Keys - The AppleiMac keyboard has an apple key on either side of the space bar. Windows-based  
systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.  
Product Reference Guide  
89  
USB Interface  
Table 19. USB GUI Key Character Set (Continued)  
GUI Key  
3053  
3054  
3055  
3056  
3057  
3065  
3066  
3067  
3068  
3069  
3070  
3071  
3072  
3073  
3074  
3075  
3076  
3077  
3078  
3079  
3080  
3081  
3082  
3083  
3084  
3085  
3086  
3087  
Keystroke  
GUI 5  
GUI 6  
GUI 7  
GUI 8  
GUI 9  
GUI A  
GUI B  
GUI C  
GUI D  
GUI E  
GUI F  
GUI G  
GUI H  
GUI I  
GUI J  
GUI K  
GUI L  
GUI M  
GUI N  
GUI O  
GUI P  
GUI Q  
GUI R  
GUI S  
GUI T  
GUI U  
GUI V  
GUI W  
Note: GUI Shift Keys - The AppleiMac keyboard has an apple key on either side of the space bar. Windows-based  
systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.  
90  
QuickScan® L  
ASCII Character Set for USB  
Table 19. USB GUI Key Character Set (Continued)  
GUI Key  
3088  
Keystroke  
GUI X  
GUI Y  
GUI Z  
3089  
3090  
Note: GUI Shift Keys - The AppleiMac keyboard has an apple key on either side of the space bar. Windows-based  
systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.  
Table 20. USB F Key Character Set  
F Keys  
5001  
5002  
5003  
5004  
5005  
5006  
5007  
5008  
5009  
5010  
5011  
5012  
5013  
5014  
5015  
5016  
5017  
5018  
5019  
5020  
5021  
Keystroke  
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
F10  
F11  
F12  
F13  
F14  
F15  
F16  
F17  
F18  
F19  
F20  
F21  
Product Reference Guide  
91  
USB Interface  
Table 20. USB F Key Character Set (Continued)  
F Keys  
5022  
Keystroke  
F22  
5023  
F23  
5024  
F24  
Table 21. USB Numeric Keypad Character Set  
Numeric Keypad  
6042  
Keystroke  
*
6043  
+
6044  
undefined  
6045  
-
6046  
.
6047  
/
6048  
0
6049  
1
6050  
2
6051  
3
6052  
4
6053  
5
6054  
6
6055  
7
6056  
8
9
6057  
6058  
Enter  
Num Lock  
6059  
Table 22. USB Extended Keypad Character Set  
Extended Keypad  
Keystroke  
Break  
7001  
7002  
7003  
7004  
7005  
Delete  
PgUp  
End  
Pg Dn  
92  
QuickScan® L  
ASCII Character Set for USB  
Table 22. USB Extended Keypad Character Set (Continued)  
Extended Keypad  
7006  
Keystroke  
Pause  
Scroll Lock  
Backspace  
Tab  
7007  
7008  
7009  
7010  
Print Screen  
Insert  
7011  
7012  
Home  
7013  
Enter  
7014  
Escape  
7015  
Up Arrow  
Down Arrow  
Left Arrow  
Right Arrow  
7016  
7017  
7018  
Product Reference Guide  
93  
USB Interface  
NOTES  
94  
QuickScan® L  
Chapter 9  
Symbologies  
Introduction  
This chapter describes symbology features and provides the programming bar codes for  
selecting these features. Before programming, follow the instructions in Chapter 2, Get-  
ting Started.  
The scanner is shipped with the settings shown in Table 23 on page 96 (also see Appen-  
dix B, Standard Defaults for all host device and miscellaneous defaults). If the default  
values suit requirements, programming is not necessary.  
To set feature values, scan a single bar code or a short bar code sequence. The settings are  
stored in non-volatile memory and are preserved even when the scanner is powered  
down.  
If not using a USB cable, select a host type (see each host chapter for specific host infor-  
mation) after the power-up beeps sound. This is only necessary upon the first power-up  
when connected to a new host.  
To return all features to default values, scan the appropriate default bar code on page 21.  
Throughout the programming bar code menus, default values are indicated with asterisks  
(*).  
Feature/Option  
* Indicates Default  
*Enable UPC-A  
Scanning Sequence Examples  
In most cases, scanning one bar code sets the parameter value. For example, to transmit  
bar code data without the UPC-A check digit, simply scan the Do Not Transmit UPC-  
A Check Digit bar code under Transmit UPC-A Check Digit on page 104. The scanner  
issues a fast warble beep and the LED turns green, signifying a successful parameter entry.  
Other parameters, such as Set Length(s) for D 2 of 5, require scanning several bar codes.  
See the individual parameter, such as Set Length(s) for D 2 of 5, for this procedure.  
Errors While Scanning  
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan  
the correct parameter.  
Product Reference Guide  
95  
Symbologies  
Symbology Parameter Defaults  
Table 23 lists the defaults for all symbologies parameters. To change any option, scan the  
appropriate bar code(s) provided in the Symbologies Parameters section beginning on  
page 99.  
See Appendix B, Standard Defaults for all user preferences, hosts, symbolo-  
gies, and miscellaneous default parameters.  
NOTE  
Table 23. Symbology Defaults  
Parameter  
Default  
Page Number  
UPC/EAN  
UPC-A  
Enable  
Enable  
99  
UPC-E  
99  
UPC-E1  
Disable  
100  
101  
101  
101  
103  
104  
104  
105  
105  
106  
107  
108  
109  
109  
110  
110  
EAN-8/JAN 8  
Enable  
EAN-13/JAN 13  
Enable  
Bookland EAN  
Disable  
Decode UPC/EAN/JAN Supplementals (2 and 5 digits)  
Decode UPC/EAN/JAN Supplemental Redundancy  
Transmit UPC-A Check Digit  
Transmit UPC-E Check Digit  
Transmit UPC-E1 Check Digit  
UPC-A Preamble  
Ignore  
7
Enable  
Enable  
Enable  
System Character  
System Character  
System Character  
Disable  
UPC-E Preamble  
UPC-E1 Preamble  
Convert UPC-E to A  
Convert UPC-E1 to A  
EAN-8/JAN-8 Extend  
UCC Coupon Extended Code  
Code 128  
Disable  
Disable  
Disable  
Code 128  
Enable  
Enable  
111  
111  
UCC/EAN-128  
96  
QuickScan® L  
Symbology Parameter Defaults  
Table 23. Symbology Defaults (Continued)  
Parameter  
Default  
Page Number  
ISBT 128 (non-concatenated)  
Code 39  
Enable  
112  
Code 39  
Enable  
Disable  
Disable  
Disable  
2 to 55  
Disable  
Disable  
Disable  
Disable  
112  
113  
113  
114  
115  
116  
116  
117  
118  
Trioptic Code 39  
Convert Code 39 to Code 32 (Italian Pharmacy Code)  
Code 32 Prefix  
Set Length(s) for Code 39  
Code 39 Check Digit Verification  
Transmit Code 39 Check Digit  
Code 39 Full ASCII Conversion  
Buffer Code 39  
Code 93  
Code 93  
Disable  
4 to 55  
120  
122  
Set Length(s) for Code 93  
Code 11  
Code 11  
Disable  
4 to 55  
Disable  
Disable  
122  
124  
125  
126  
Set Lengths for Code 11  
Code 11 Check Digit Verification  
Transmit Code 11 Check Digit(s)  
Interleaved 2 of 5 (ITF)  
Interleaved 2 of 5 (ITF)  
Set Lengths for I 2 of 5  
I 2 of 5 Check Digit Verification  
Transmit I 2 of 5 Check Digit  
Convert I 2 of 5 to EAN 13  
Enable  
14  
126  
128  
129  
129  
130  
Disable  
Disable  
Disable  
Product Reference Guide  
97  
Symbologies  
Table 23. Symbology Defaults (Continued)  
Parameter  
Default  
Page Number  
Discrete 2 of 5 (DTF)  
Discrete 2 of 5  
Disable  
12  
130  
132  
Set Length(s) for D 2 of 5  
Chinese 2 of 5  
Enable/Disable Chinese 2 of 5  
Codabar (NW - 7)  
Codabar  
Disable  
132  
Disable  
5 to 55  
Disable  
Disable  
133  
134  
135  
136  
Set Lengths for Codabar  
CLSI Editing  
NOTIS Editing  
MSI  
MSI  
Disable  
2 to 55  
136  
138  
138  
139  
139  
Set Length(s) for MSI  
MSI Check Digits  
One  
Transmit MSI Check Digit  
MSI Check Digit Algorithm  
GS1 DataBar (RSS)  
DataBar Omnidirectional (RSS-14)  
DataBar Limited  
Disable  
Mod 10/Mod 10  
Disable  
Disable  
Disable  
Disable  
140  
140  
140  
141  
DataBar Expanded  
Convert DataBar to UPC/EAN  
Symbology - Specific Security Levels  
Redundancy Level  
Security Levels  
1
0
143  
144  
145  
Bi-directional Redundancy  
Disable  
98  
QuickScan® L  
UPC/EAN  
UPC/EAN  
Enable/Disable UPC-A/UPC-E  
To enable or disable UPC-A or UPC-E, scan the appropriate bar code below.  
*Enable UPC-A  
Disable UPC-A  
*Enable UPC-E  
Disable UPC-E  
Product Reference Guide  
99  
Symbologies  
Enable/Disable UPC-E1  
UPC-E1 is disabled by default.  
To enable or disable UPC-E1, scan the appropriate bar code below.  
UPC-E1 is not a UCC (Uniform Code Council) approved symbology.  
NOTE  
Enable UPC-E1  
*Disable UPC-E1  
100  
QuickScan® L  
UPC/EAN  
Enable/Disable EAN-13/EAN-8  
To enable or disable EAN-13 or EAN-8, scan the appropriate bar code below.  
*Enable EAN-13  
Disable EAN-13  
*Enable EAN-8  
Disable EAN-8  
Enable/Disable Bookland EAN  
To enable or disable Bookland EAN, scan the appropriate bar code below.  
Enable Bookland EAN  
*Disable Bookland EAN  
Product Reference Guide  
101  
Symbologies  
Decode UPC/EAN/JAN Supplementals  
Supplementals are bar codes appended according to specific format conventions (e.g.,  
UPC A+2, UPC E+2, EAN 13+2). Six options are available.  
If Decode UPC/EAN/JAN Only With Supplementals is selected, UPC/EAN bar codes  
without supplementals are not decoded.  
If Ignore Supplementals is selected, and the scanner is presented with a UPC/EAN/  
JAN with a supplemental, the UPC/EAN/JAN is decoded and the supplemental bar  
code is ignored.  
An Autodiscriminate Option is also available. If this option is selected, choose an appro-  
priate value from the next page. A value of 5 or more is recommended.  
Select Enable 378/379 Supplemental Mode to delay only EAN-13/JAN-13 bar codes  
starting with a ‘378’ or ‘379’ prefix by the supplemental search process. All other UPC/  
EAN/JAN bar codes are exempted from the search and are reported instantly upon  
decode.  
Select Enable 978 Supplemental Mode to delay only EAN-13/JAN-13 bar codes starting  
with a ‘978’ prefix by the supplemental search process. All other UPC/EAN bar codes are  
exempted from the search and are reported instantly upon their decode.  
Select Enable Smart Supplemental Mode to delay only EAN-13/JAN-13 bar codes start-  
ing with a ‘378’, ‘379’, or ‘978’ prefix by the supplemental search process. All other UPC/  
EAN bar codes are exempted from the search and are reported instantly upon their  
decode.  
To minimize the risk of invalid data transmission, select either to decode or  
ignore supplemental characters.  
NOTE  
102  
QuickScan® L  
UPC/EAN  
Decode UPC/EAN/JAN Supplementals (continued)  
Decode UPC/EAN/JAN Only With Supplementals  
*Ignore Supplementals  
Autodiscriminate UPC/EAN/JAN Supplementals  
Enable 378/379 Supplemental Mode  
Enable 978 Supplemental Mode  
Enable Smart Supplemental Mode  
Product Reference Guide  
103  
Symbologies  
UPC/EAN/JAN Supplemental Redundancy  
With Autodiscriminate UPC/EAN/JAN Supplementals selected, this option adjusts the  
number of times a bar code without supplementals is decoded before transmission. The  
range is from two to twenty-two times. Five or above is recommended when decoding a  
mix of UPC/EAN bar codes with and without supplementals, and the autodiscriminate  
option is selected. The default is set at seven.  
Scan the bar code below to set a decode redundancy value. Next, scan two numeric bar  
codes in Appendix E, Keypad. Single digit numbers must have a leading zero. To correct  
an error or change a selection, scan the CANCEL bar code located in Appendix E, Key-  
pad.  
UPC/EAN/JAN Supplemental Redundancy  
Transmit UPC-A Check Digit  
The check digit is the last character of the bar code used to verify the integrity of the data.  
Scan the appropriate bar code below to transmit the bar code data with or without the  
UPC-A check digit. It is always verified to guarantee the integrity of the data.  
*Transmit UPC-A Check Digit  
Do Not Transmit UPC-A Check Digit  
104  
QuickScan® L  
UPC/EAN  
Transmit UPC-E Check Digit  
The check digit is the last character of the bar code used to verify the integrity of the data.  
Scan the appropriate bar code below to transmit the bar code data with or without the  
UPC-E check digit. It is always verified to guarantee the integrity of the data.  
*Transmit UPC-E Check Digit  
Do Not Transmit UPC-E Check Digit  
Transmit UPC-E1 Check Digit  
The check digit is the last character of the bar code used to verify the integrity of the data.  
Scan the appropriate bar code below to transmit the bar code data with or without the  
UPC-E1 check digit. It is always verified to guarantee the integrity of the data.  
*Transmit UPC-E1 Check Digit  
Do Not Transmit UPC-E1 Check Digit  
Product Reference Guide  
105  
Symbologies  
UPC-A Preamble  
Preamble characters are part of the UPC bar code consisting of Country Code and Sys-  
tem Character. Three options are given for transmitting UPC-A preamble to the host de-  
vice: transmit System Character only, transmit System Character and Country Code (“0”  
for USA), and no preamble transmitted. Scan a bar code below to match the host system.  
No Preamble  
(<DATA>)  
*System Character  
(<SYSTEM CHARACTER> <DATA>)  
System Character & Country Code  
(< COUNTRY CODE> <SYSTEM CHARACTER> <DA-  
TA>)  
106  
QuickScan® L  
UPC/EAN  
UPC-E Preamble  
Preamble characters are part of the UPC bar code consisting of Country Code and Sys-  
tem Character. Three options are given for transmitting UPC-E preamble to the host de-  
vice: transmit System Character only, transmit System Character and Country Code (“0”  
for USA), and no preamble transmitted. Scan a bar code below to match the host system.  
No Preamble  
(<DATA>)  
*System Character  
(<SYSTEM CHARACTER> <DATA>)  
System Character & Country Code  
(< COUNTRY CODE> <SYSTEM CHARACTER>  
<DATA>)  
Product Reference Guide  
107  
Symbologies  
UPC-E1 Preamble  
Preamble characters are part of the UPC bar code consisting of Country Code and Sys-  
tem Character. Three options are given for transmitting UPC-E1 preamble to the host  
device: transmit System Character only, transmit System Character and Country Code  
(“0” for USA), and no preamble transmitted. Scan a bar code below to match the host  
system.  
No Preamble  
(<DATA>)  
*System Character  
(<SYSTEM CHARACTER> <DATA>)  
System Character & Country Code  
(< COUNTRY CODE> <SYSTEM CHARACTER> <DA-  
TA>)  
108  
QuickScan® L  
UPC/EAN  
Convert UPC-E to UPC-A  
Enable this to convert UPC-E (zero suppressed) decoded data to UPC-A format before  
transmission. After conversion, the data follows UPC-A format and is affected by UPC-  
A programming selections (e.g., Preamble, Check Digit).  
When disabled, UPC-E decoded data is transmitted as UPC-E data, without conversion.  
Convert UPC-E to UPC-A  
(Enable)  
*Do Not Convert UPC-E to UPC-A  
(Disable)  
Convert UPC-E1 to UPC-A  
Enable this to convert UPC-E1 decoded data to UPC-A format before transmission. Af-  
ter conversion, the data follows UPC-A format and is affected by UPC-A programming  
selections (e.g., Preamble, Check Digit).  
When disabled, UPC-E1 decoded data is transmitted as UPC-E1 data, without conver-  
sion.  
Convert UPC-E1 to UPC-A  
(Enable)  
*Do Not Convert UPC-E1 to UPC-A  
(Disable)  
Product Reference Guide  
109  
Symbologies  
EAN-8/JAN-8 Extend  
When enabled, this parameter adds five leading zeros to decoded EAN-8 bar codes to  
make them compatible in format to EAN-13 bar codes.  
When disabled, EAN-8 bar codes are transmitted as is.  
Enable EAN/JAN Zero Extend  
*Disable EAN/JAN Zero Extend  
UCC Coupon Extended Code  
When enabled, this parameter decodes UPCA bar codes starting with digit ‘5’, EAN-13  
bar codes starting with digit ‘99’, and UPCA/EAN-128 Coupon Codes. UPCA, EAN-  
13 and EAN-128 must be enabled to scan all types of Coupon Codes.  
Enable UCC Coupon Extended Code  
*Disable UCC Coupon Extended Code  
Use the Decode UPC/EAN Supplemental Redundancy parameter to control  
autodiscrimination of the EAN128 (right half) of a coupon code.  
NOTE  
110  
QuickScan® L  
Code 128  
Code 128  
Enable/Disable Code 128  
To enable or disable Code 128, scan the appropriate bar code below.  
*Enable Code 128  
Disable Code 128  
Enable/Disable UCC/EAN-128  
To enable or disable UCC/EAN-128, scan the appropriate bar code below.  
*Enable UCC/EAN-128  
Disable UCC/EAN-128  
Product Reference Guide  
111  
Symbologies  
Enable/Disable ISBT 128  
ISBT 128 is a variant of Code 128 used in the blood bank industry. Scan the appropriate  
bar code below to enable or disable ISBT 128. If necessary, the host must perform con-  
catenation of the ISBT data.  
*Enable ISBT 128  
Disable ISBT 128  
Code 39  
Enable/Disable Code 39  
To enable or disable Code 39, scan the appropriate bar code below.  
*Enable Code 39  
Disable Code 39  
112  
QuickScan® L  
Code 39  
Enable/Disable Trioptic Code 39  
Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridg-  
es. Trioptic Code 39 bar codes always contain six characters. To enable or disable Triop-  
tic Code 39, scan the appropriate bar code below.  
Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.  
NOTE  
Enable Trioptic Code 39  
*Disable Trioptic Code 39  
Convert Code 39 to Code 32  
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the  
appropriate bar code below to enable or disable converting Code 39 to Code 32.  
Code 39 must be enabled for this parameter to function.  
NOTE  
Enable Convert Code 39 to Code 32  
*Disable Convert Code 39 to Code 32  
Product Reference Guide  
113  
Symbologies  
Code 32 Prefix  
Scan the appropriate bar code below to enable or disable adding the prefix character “A”  
to all Code 32 bar codes.  
Convert Code 39 to Code 32 must be enabled for this parameter to function.  
NOTE  
Enable Code 32 Prefix  
*Disable Code 32 Prefix  
Set Lengths for Code 39  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for Code 39 to any length, one or  
two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled,  
Length Within a Range or Any Length are the preferred options.  
When setting lengths for different bar code types by scanning single digit  
numbers, single digit numbers must always be preceded by a leading zero.  
NOTE  
One Discrete Length - Select this option to decode only Code 39 bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only Code 39 bar codes with 14 characters, scan Code 39 - One  
Discrete Length, then scan 1 followed by 4. To correct an error or change the selection,  
scan the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only Code 39 bar codes contain-  
ing either of two selected lengths. Select lengths using the numeric bar codes in Appen-  
dix E, Keypad. For example, to decode only those Code 39 bar codes containing either 2  
or 14 characters, select Code 39 - Two Discrete Lengths, then scan 0, 2, 1, and then  
4. To correct an error or change the selection, scan the CANCEL bar code located in  
Appendix E, Keypad.  
114  
QuickScan® L  
Code 39  
Set Lengths for Code 39 (continued)  
Length Within Range - Select this option to decode a Code 39 bar code with a spe-  
cific length range. Select lengths using numeric bar codes in Appendix E, Keypad.  
For example, to decode Code 39 bar codes containing between 4 and 12 characters,  
first scan Code 39 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers  
must always be preceded by a leading zero). To correct an error or change the selection,  
scan the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Select this option to decode Code 39 bar codes containing any number of  
characters within the scanner capability.  
Code 39 - One Discrete Length  
Code 39 - Two Discrete Lengths  
Code 39 - Length Within Range  
Code 39 - Any Length  
Product Reference Guide  
115  
Symbologies  
Code 39 Check Digit Verification  
When this feature is enabled, the scanner checks the integrity of all Code 39 bar codes to  
verify that the data complies with specified check digit algorithm. Only Code 39 bar  
codes which include a modulo 43 check digit are decoded. Enable this feature if the Code  
39 bar codes contain a Modulo 43 check digit.  
Enable Code 39 Check Digit  
*Disable Code 39 Check Digit  
Transmit Code 39 Check Digit  
Scan the appropriate bar code below to transmit Code 39 data with or without the check  
digit.  
Code 39 Check Digit Verification must be enabled for this parameter to func-  
tion.  
NOTE  
Transmit Code 39 Check Digit  
(Enable)  
*Do Not Transmit Code 39 Check Digit  
(Disable)  
116  
QuickScan® L  
Code 39  
Code 39 Full ASCII Conversion  
Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full  
ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar  
code below.  
Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.  
Code 39 Full ASCII to Full ASCII Correlation is host-dependent and is  
described in the ASCII Character Set table for the appropriate interface. See  
ASCII Character Set for Keyboard Wedge on page 64, ASCII Character  
Set for RS-232 on page 49 and ASCII Character Set for USB on page 84  
for the appropriate interface.  
NOTE  
Enable Code 39 Full ASCII  
*Disable Code 39 Full ASCII  
Product Reference Guide  
117  
Symbologies  
Code 39 Buffering (Scan & Store)  
This feature allows the scanner to accumulate data from multiple Code 39 bar codes.  
Selecting the Scan and Store option (Buffer Code 39) temporarily buffers all Code 39  
bar codes having a leading space as a first character for later transmission. The leading  
space is not buffered.  
Decode of a valid Code 39 bar code with no leading space causes transmission in se-  
quence of all buffered data in a first-in first-out format, plus transmission of the “trigger-  
ing” bar code. See the following pages for further details.  
When the Do Not Buffer Code 39 option is selected, all decoded Code 39 bar codes  
are transmitted immediately without being stored in the buffer.  
Code 39 Buffering (Scan & Store)  
This feature affects Code 39 only. If selecting Buffer Code 39, we recommend configur-  
ing the scanner to decode Code 39 symbology only.  
Buffer Code 39  
(Enable)  
*Do Not Buffer Code 39  
(Disable)  
While there is data in the transmission buffer, selecting Do Not Buffer Code 39 is not  
allowed. The buffer holds 200 bytes of information.  
To disable Code 39 buffering when there is data in the transmission buffer, first force the  
buffer transmission (see Transmit Buffer on page 119) or clear the buffer.  
Buffer Data  
To buffer data, Code 39 buffering must be enabled and a Code 39 bar code must be read  
with a space immediately following the start pattern.  
- Unless the data overflows the transmission buffer, the scanner issues a low/high beep to  
indicate successful decode and buffering. (For overflow conditions, see Overfilling  
Transmission Buffer on page 120.)  
- The scanner adds the decoded data excluding the leading space to the transmission  
buffer.  
- No transmission occurs.  
118  
QuickScan® L  
Code 39  
Clear Transmission Buffer  
Because the Clear Buffer contains only the dash (minus) character, set the  
Code 39 length to include length 1 before scanning this bar code.  
NOTE  
To clear the transmission buffer, scan the Clear Buffer bar code below, which contains  
only a start character, a dash (minus), and a stop character.  
- The scanner issues a short high/low/high beep.  
- The scanner erases the transmission buffer.  
- No transmission occurs.  
Clear Buffer  
Transmit Buffer  
Because the Transmit Buffer contains only a plus (+) character, set the Code  
39 length to include length 1 before scanning this bar code.  
NOTE  
There are two methods to transmit the Code 39 buffer.  
1. Scan the Transmit Buffer bar code below which contains only a start character, a plus (+),  
and a stop character.  
- The scanner transmits and clears the buffer.  
- The scanner issues a low/high beep.  
Transmit Buffer  
2. Scan a Code 39 bar code with a leading character other than a space.  
- The scanner appends new decode data to buffered data.  
- The scanner transmits and clears the buffer.  
- The scanner signals that the buffer was transmitted with a low/high beep.  
- Scanner transmits and clears the buffer.  
Product Reference Guide  
119  
Symbologies  
Overfilling Transmission Buffer  
The Code 39 buffer holds 200 characters. If the bar code just read results in an overflow  
of the transmission buffer:  
The scanner indicates that the bar code was rejected by issuing three long, high beeps.  
No transmission occurs. The data in the buffer is not affected.  
Attempt to Transmit an Empty Buffer  
If the bar code just read was the Transmit Buffer bar code and the Code 39 buffer is emp-  
ty:  
A short low/high/low beep signals that the buffer is empty.  
No transmission occurs.  
The buffer remains empty.  
Code 93  
Enable/Disable Code 93  
To enable or disable Code 93, scan the appropriate bar code below.  
Enable Code 93  
*Disable Code 93  
120  
QuickScan® L  
Code 93  
Set Lengths for Code 93  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for Code 93 to any length, one or  
two discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only Code 93 bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only Code 93 bar codes with 14 characters, scan Code 93 - One  
Discrete Length, then scan 1 followed by 4. To correct an error or to change the selec-  
tion, scan the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only Code 93 bar codes contain-  
ing either of two selected lengths. Select lengths using the numeric bar codes in Appen-  
dix E, Keypad. For example, to decode only those Code 93 bar codes containing either 2  
or 14 characters, select Code 93 - Two Discrete Lengths, then scan 0, 2, 1, and then  
4. To correct an error or to change the selection, scan the CANCEL bar code located  
in Appendix E, Keypad.  
Length Within Range - Select this option to decode a Code 93 bar code with a spe-  
cific length range. Select lengths using the numeric bar codes in Appendix E, Key-  
pad. For example, to decode Code 93 bar codes containing between 4 and 12  
characters, first scan Code 93 - Length Within Range. Then scan 0, 4, 1, and 2 (single  
digit numbers must always be preceded by a leading zero). To correct an error or change  
the selection, scan the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode Code 93 bar codes containing any number of  
characters within the scanner’s capability.  
Product Reference Guide  
121  
Symbologies  
Set Lengths for Code 93 (continued)  
Code 93 - One Discrete Length  
Code 93 - Two Discrete Lengths  
Code 93 - Length Within Range  
Code 93 - Any Length  
Code 11  
To enable or disable Code 11, scan the appropriate bar code below.  
Enable Code 11  
*Disable Code 11  
122  
QuickScan® L  
Code 11  
Set Lengths for Code 11  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for Code 11 to any length, one or  
two discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only Code 11 bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only Code 11 bar codes with 14 characters, scan Code 11 - One  
Discrete Length, then scan 1 followed by 4. To correct an error or to change the selec-  
tion, scan the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only Code 11 bar codes contain-  
ing either of two selected lengths. Select lengths using the numeric bar codes in Appen-  
dix E, Keypad. For example, to decode only those Code 11 bar codes containing either 2  
or 14 characters, select Code 11 - Two Discrete Lengths, then scan 0, 2, 1, and then  
4. To correct an error or to change the selection, scan the CANCEL bar code located  
in Appendix E, Keypad.  
Length Within Range - Select this option to decode a Code 11 bar code with a spe-  
cific length range. Select lengths using numeric bar codes in Appendix E, Keypad.  
For example, to decode Code 11 bar codes containing between 4 and 12 characters,  
first scan Code 11 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers  
must always be preceded by a leading zero). To correct an error or change the selection,  
scan the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode Code 11 bar codes containing any number of  
characters within the scanner capability.  
Product Reference Guide  
123  
Symbologies  
Set Lengths for Code 11 (continued)  
Code 11 - One Discrete Length  
Code 11 - Two Discrete Lengths  
Code 11 - Length Within Range  
Code 11 - Any Length  
124  
QuickScan® L  
Code 11  
Code 11 Check Digit Verification  
This feature allows the scanner to check the integrity of all Code 11 bar codes to verify  
that the data complies with the specified check digit algorithm. This selects the check  
digit mechanism for the decoded Code 11 bar code. The options are to check for one  
check digit, check for two check digits, or disable the feature.  
To enable this feature, scan the bar code below corresponding to the number of check  
digits encoded in your Code 11 bar codes.  
*Disable  
One Check Digit  
Two Check Digits  
Product Reference Guide  
125  
Symbologies  
Transmit Code 11 Check Digits  
This feature selects whether or not to transmit the Code 11 check digit(s).  
Code 11 Check Digit Verification must be enabled for this parameter to function.  
NOTE  
Transmit Code 11 Check Digit(s)  
(Enable)  
*Do Not Transmit Code 11 Check Digit(s)  
(Disable)  
Interleaved 2 of 5 (ITF)  
Enable/Disable Interleaved 2 of 5  
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below, and select  
an Interleaved 2 of 5 length from the following pages.  
*Enable Interleaved 2 of 5  
Disable Interleaved 2 of 5  
126  
QuickScan® L  
Interleaved 2 of 5 (ITF)  
Set Lengths for Interleaved 2 of 5  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for I 2 of 5 to any length, one or  
two discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only I 2 of 5 bar codes containing a  
selected length. Select the length using the numeric bar codes in scan the CANCEL bar  
code located in Appendix E, Keypad. For example, to decode only I 2 of 5 bar codes  
with 14 characters, scan I 2 of 5 - One Discrete Length, then scan 1 followed by 4. To  
correct an error or to change the selection, scan the CANCEL bar code located in  
Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only I 2 of 5 bar codes containing  
either of two selected lengths. Select lengths using the numeric bar codes in Appendix  
E, Keypad. For example, to decode only those I 2 of 5 bar codes containing either 2 or  
14 characters, select I 2 of 5 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To  
correct an error or to change the selection, scan the CANCEL bar code located in  
Appendix E, Keypad.  
Length Within Range - Select this option to decode an I 2 of 5 bar code with a spe-  
cific length range. Select lengths using numeric bar codes in Appendix E, Keypad.  
For example, to decode I 2 of 5 bar codes containing between 4 and 12 characters,  
first scan I 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers  
must always be preceded by a leading zero). To correct an error or change the selection,  
can the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode I 2 of 5 bar codes containing any number of  
characters within the scanner capability.  
Due to the construction of the I 2 of 5 symbology, it is possible for a scan line  
covering only a portion of the code to be interpreted as a complete scan,  
yielding less data than is encoded in the bar code. To prevent this, select  
specific lengths (I 2 of 5 - One Discrete Length - Two Discrete Lengths) for I 2  
of 5 applications.  
NOTE  
Product Reference Guide  
127  
Symbologies  
Set Lengths for Interleaved 2 of 5 (continued)  
I 2 of 5 - One Discrete Length  
I 2 of 5 - Two Discrete Lengths  
*I 2 of 5 - Length Within Range  
(Default range is 2 to 55)  
I 2 of 5 - Any Length  
128  
QuickScan® L  
Interleaved 2 of 5 (ITF)  
I 2 of 5 Check Digit Verification  
When this feature is enabled, the scanner checks the integrity of all I 2 of 5 bar codes to  
verify the data complies with either the specified Uniform Symbology Specification  
(USS), or the Optical Product Code Council (OPCC) check digit algorithm.  
*Disable  
USS Check Digit  
OPCC Check Digit  
Transmit I 2 of 5 Check Digit  
Scan the appropriate bar code below to transmit I 2 of 5 data with or without the check  
digit.  
Transmit I 2 of 5 Check Digit  
(Enable)  
*Do Not Transmit I 2 of 5 Check Digit  
(Disable)  
Product Reference Guide  
129  
Symbologies  
Convert I 2 of 5 to EAN-13  
Enable this parameter to convert 14-character I 2 of 5 codes to EAN-13, and transmit to  
the host as EAN-13. To accomplish this, the I 2 of 5 code must be enabled, and the code  
must have a leading zero and a valid EAN-13 check digit.  
Convert I 2 of 5 to EAN-13  
(Enable)  
*Do Not Convert I 2 of 5 to EAN-13  
(Disable)  
Discrete 2 of 5 (DTF)  
Enable/Disable Discrete 2 of 5  
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.  
Enable Discrete 2 of 5  
*Disable Discrete 2 of 5  
130  
QuickScan® L  
Discrete 2 of 5 (DTF)  
Set Lengths for Discrete 2 of 5  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for D 2 of 5 to any length, one or  
two discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only D 2 of 5 bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only D 2 of 5 bar codes with 14 characters, scan D 2 of 5 - One  
Discrete Length, then scan 1 followed by 4. To correct an error or to change the selec-  
tion, scan the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only D 2 of 5 bar codes contain-  
ing either of two selected lengths. Select lengths using the numeric bar codes in Appen-  
dix E, Keypad. For example, to decode only those D 2 of 5 bar codes containing either 2  
or 14 characters, select D 2 of 5 - Two Discrete Lengths, then scan 0, 2, 1, and then 4.  
To correct an error or to change the selection, scan the CANCEL bar code located in  
Appendix E, Keypad.  
Length Within Range - Select this option to decode a D 2 of 5 bar code with a spe-  
cific length range. Select lengths using numeric bar codes in Appendix E, Keypad.  
For example, to decode D 2 of 5 bar codes containing between 4 and 12 characters,  
first scan D 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers  
must always be preceded by a leading zero). To correct an error or change the selection,  
scan the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode D 2 of 5 bar codes containing any number of  
characters within the scanner capability.  
Due to the construction of the D 2 of 5 symbology, it is possible for a scan  
line covering only a portion of the code to be interpreted as a complete scan,  
yielding less data than is encoded in the bar code. To prevent this, select  
specific lengths (D 2 of 5 - One Discrete Length - Two Discrete Lengths) for D  
2 of 5 applications.  
NOTE  
Product Reference Guide  
131  
Symbologies  
Set Lengths for Discrete 2 of 5 (continued)  
D 2 of 5 - One Discrete Length  
D 2 of 5 - Two Discrete Lengths  
D 2 of 5 - Length Within Range  
D 2 of 5 - Any Length  
Chinese 2 of 5  
Enable/Disable Chinese 2 of 5  
To enable or disable Chinese 2 of 5, scan the appropriate bar code below.  
Enable Chinese 2 of 5  
*Disable Chinese 2 of 5  
132  
QuickScan® L  
Codabar (NW - 7)  
Codabar (NW - 7)  
Enable/Disable Codabar  
To enable or disable Codabar, scan the appropriate bar code below.  
Enable Codabar  
*Disable Codabar  
Set Lengths for Codabar  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for Codabar to any length, one or  
two discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only Codabar bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only Codabar bar codes with 14 characters, scan Codabar - One  
Discrete Length, then scan 1 followed by 4. To correct an error or to change the selec-  
tion, scan the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only Codabar bar codes contain-  
ing either of two selected lengths. Select lengths using the numeric bar codes in Appen-  
dix E, Keypad. For example, to decode only Codabar bar codes containing either 2 or 14  
characters, select Codabar - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To  
correct an error or to change the selection, scan the CANCEL bar code located in  
Appendix E, Keypad.  
Length Within Range - Select this option to decode a Codabar bar code with a spe-  
cific length range. Select lengths using numeric bar codes in Appendix E, Keypad.  
For example, to decode Codabar bar codes containing between 4 and 12 characters,  
first scan Codabar - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers  
must always be preceded by a leading zero). To correct an error or change the selection,  
scan the CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode Codabar bar codes containing any number of  
characters within the scanner capability.  
Product Reference Guide  
133  
Symbologies  
Set Lengths for Codabar (continued)  
Codabar - One Discrete Length  
Codabar - Two Discrete Lengths  
Codabar - Length Within Range  
Codabar - Any Length  
134  
QuickScan® L  
Codabar (NW - 7)  
CLSI Editing  
When enabled, this parameter strips the start and stop characters and inserts a space after  
the first, fifth, and tenth characters of a 14-character Codabar bar code. Enable this fea-  
ture if your host system requires this data format.  
Bar Code length does not include start and stop characters.  
NOTE  
Enable CLSI Editing  
*Disable CLSI Editing  
Product Reference Guide  
135  
Symbologies  
NOTIS Editing  
When enabled, this parameter strips the start and stop characters from a decoded Coda-  
bar bar code. Enable this feature if your host system requires this data format.  
Enable NOTIS Editing  
*Disable NOTIS Editing  
MSI  
Enable/Disable MSI  
To enable or disable MSI, scan the appropriate bar code below.  
Enable MSI  
*Disable MSI  
136  
QuickScan® L  
MSI  
Set Lengths for MSI  
The length of a code refers to the number of characters (i.e., human readable characters),  
including check digit(s) the code contains. Set lengths for MSI to any length, one or two  
discrete lengths, or lengths within a specific range.  
One Discrete Length - Select this option to decode only MSI bar codes containing a  
selected length. Select the length using the numeric bar codes in Appendix E, Keypad.  
For example, to decode only MSI bar codes with 14 characters, scan MSI - One Discrete  
Length, then scan 1 followed by 4. To correct an error or to change the selection, scan  
the CANCEL bar code located in Appendix E, Keypad.  
Two Discrete Lengths - Select this option to decode only MSI bar codes containing  
either of two selected lengths. Select lengths using the numeric bar codes in Appendix  
E, Keypad. For example, to decode only MSI bar codes containing either 2 or 14 charac-  
ters, select MSI - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To correct an  
error or to change the selection, scan the CANCEL bar code located in Appendix E,  
Keypad.  
Length Within Range - Select this option to decode a MSI bar code with a specific  
length range. Select lengths using numeric bar codes in Appendix E, Keypad. For  
example, to decode MSI bar codes containing between 4 and 12 characters, first scan  
MSI - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always  
be preceded by a leading zero). To correct an error or change the selection, scan the  
CANCEL bar code located in Appendix E, Keypad.  
Any Length - Scan this option to decode MSI bar codes containing any number of charac-  
ters within the scanner capability.  
Due to the construction of the MSI symbology, it is possible for a scan line  
covering only a portion of the code to be interpreted as a complete scan,  
yielding less data than is encoded in the bar code. To prevent this, select  
specific lengths (MSI - One Discrete Length - Two Discrete Lengths) for MSI  
applications.  
NOTE  
Product Reference Guide  
137  
Symbologies  
Set Lengths for MSI (continued)  
MSI - One Discrete Length  
MSI - Two Discrete Lengths  
MSI - Length Within Range  
*MSI - Any Length  
MSI Check Digits  
With MSI bar codes, one check digit is mandatory and always verified by the reader. The  
second check digit is optional. If the MSI codes include two check digits, scan the Two  
MSI Check Digits bar code to enable verification of the second check digit.  
See MSI Check Digit Algorithm on page 139 for the selection of second digit algorithms.  
*One MSI Check Digit  
Two MSI Check Digits  
138  
QuickScan® L  
MSI  
Transmit MSI Check Digit(s)  
Scan the appropriate bar code below to transmit MSI data with or without the check dig-  
it.  
Transmit MSI Check Digit(s)  
(Enable)  
*Do Not Transmit MSI Check Digit(s)  
(Disable)  
MSI Check Digit Algorithm  
Two algorithms are possible for the verification of the second MSI check digit. Select the  
bar code below corresponding to the algorithm used to encode your check digit.  
MOD 10/MOD 11  
*MOD 10/MOD 10  
Product Reference Guide  
139  
Symbologies  
GS1 DataBar (RSS)  
The variants of GS1 DataBar are DataBar Omnidirectional, DataBar Expanded and Da-  
taBar Limited.  
The GS1 DataBar symbology family was formerly known as RSS. Equivalents  
for each variant in the family are:  
RSS-14  
RSS Expanded = DataBar Expanded  
RSS Limited DataBar Limited  
=
DataBar Omnidirectional  
NOTE  
=
DataBar Omnidirectional and DataBar Expanded include stacked versions. Scan the ap-  
propriate bar code below to enable or disable each variant of DataBar.  
Enable DataBar Omnidirectional  
*Disable DataBar Omnidirectional  
Enable DataBar Limited  
*Disable DataBar Limited  
Enable DataBar Expanded  
*Disable DataBar Expanded  
140  
QuickScan® L  
GS1 DataBar (RSS)  
Convert DataBar to UPC/EAN  
This parameter only applies to DataBar Omnidirectional and DataBar Limited bar codes  
not decoded as part of a Composite bar code. Enable this to strip the leading '010' from  
DataBar Omnidirectional and DataBar Limited bar codes encoding a single zero as the  
first digit, and report the bar code as EAN-13.  
For bar codes beginning with two or more zeros but not six zeros, this parameter strips  
the leading '0100' and reports the bar code as UPC-A. The UPC-A Preamble parameter  
that transmits the system character and country code applies to converted bar codes.  
Note that neither the system character nor the check digit can be stripped.  
Enable Convert DataBar to UPC/EAN  
*Disable Convert DataBar to UPC/EAN  
Product Reference Guide  
141  
Symbologies  
Symbology - Specific Security Levels  
Redundancy Level  
The scanner offers four levels of decode redundancy. Select higher redundancy levels for  
decreasing levels of bar code quality. As redundancy levels increase, the scanner’s aggres-  
siveness decreases.  
Select the redundancy level appropriate for the bar code quality.  
Redundancy Level 1  
The following code types must be successfully read twice before being decoded:  
Table 24. Redundancy Level 1 Code Types  
Code Type  
Code Length  
8 characters or less  
Codabar  
MSI  
4 characters or less  
8 characters or less  
8 characters or less  
D 2 of 5  
I 2 of 5  
Redundancy Level 2  
The following code types must be successfully read twice before being decoded:  
Table 25. Redundancy Level 2 Code Types  
Code Type  
All  
Code Length  
All  
Redundancy Level 3  
Code types other than the following must be successfully read twice before being decod-  
ed. The following codes must be read three times:  
Table 26. Redundancy Level 3 Code Types  
Code Type  
Code Length  
4 characters or less  
MSI  
D 2 of 5  
I 2 of 5  
Codabar  
8 characters or less  
8 characters or less  
8 characters or less  
142  
QuickScan® L  
Symbology - Specific Security Levels  
Redundancy Level 4  
The following code types must be successfully read three times before being decoded:  
Table 27. Redundancy Level 4 Code Types  
Code Type  
All  
Code Length  
All  
*Redundancy Level 1  
Redundancy Level 2  
Redundancy Level 3  
Redundancy Level 4  
Product Reference Guide  
143  
Symbologies  
Security Level  
The scanner offers four levels of decode security for delta bar codes, which include the  
Code 128 family, UPC/EAN, and Code 93. Select increasing levels of security for de-  
creasing levels of bar code quality. There is an inverse relationship between security and  
scanner aggressiveness, so choose only that level of security necessary for any given appli-  
cation.  
Security Level 0: This default setting allows the scanner to operate in its most aggressive  
state, while providing sufficient security in decoding most “in-spec” bar codes.  
Security Level 1: Select this option if misdecodes occur. This security level should elimi-  
nate most misdecodes.  
Security Level 2: Select this option if Security level 1 fails to eliminate misdecodes.  
Security Level 3: If Security Level 2 was selected and misdecodes still occur, select this  
security level. Be advised, selecting this option is an extreme measure against mis-decoding  
severely out of spec bar codes. Selecting this level of security significantly impairs the  
decoding ability of the scanner. If this level of security is necessary, try to improve the  
quality of the bar codes.  
*Security Level 0  
Security Level 1  
Security Level 2  
Security Level 3  
144  
QuickScan® L  
Symbology - Specific Security Levels  
Bi-directional Redundancy  
Enable Bi-directional Redundancy to add security to linear code type security levels.  
When enabled, a bar code must be successfully scanned in both directions (forward and  
reverse) before reporting a good decode.  
Enable Bi-directional Redundancy  
*Disable Bi-directional Redundancy  
Product Reference Guide  
145  
Symbologies  
Symbology - Intercharacter Gap  
The Code 39 and Codabar bar codeogies have an intercharacter gap that is customarily  
quite small. Due to various bar code printing technologies, this gap may grow larger than  
the maximum size allowed, causing the scanner to be unable to decode the bar code. If  
this problem is encountered, scan Large Intercharacter Gaps to tolerate out-of-specifica-  
tion bar codes.  
*Normal Intercharacter Gaps  
Large Intercharacter Gaps  
146  
QuickScan® L  
Appendix A  
Technical Specifications  
Table 28 contains Physical and Performance Characteristics, User Environment and  
Regulatory information. Table 29 provides Standard Cable Pinouts.  
Table 28. Technical Specifications  
Item  
Physical Characteristics  
Description  
2.79 in. H x 6.71 in. L x 2.59 in. W  
Dimensions  
(7.09 cm H x 17.04 cm L x 6.69 cm W)  
Approximately 4.5 oz. (128 g)  
Weight (without cable)  
5.0 VDC +/-10%  
Standby: <35mA  
Operating: 100mA  
Max: 175mA  
Voltage & Current  
Color  
Black or White  
Performance Characteristics  
Light Source (Laser)  
Scan Rate  
650nm laser diode  
100 scans per second  
Scan Width  
47°  
Roll (Tilt) Tolerance  
Pitch Tolerance  
Skew (Yaw) Tolerance  
30° from normal  
65°  
60°  
13 mil (100% UPC/EAN): 0 to 9 in. (22.86 cm)  
5 mil (Code 39): 0.5 to 5.5 in. (1.27 cm to 13.97 cm)  
(See Depth of Field on page 14.)  
Typical DOF Distance  
Print Contrast Minimum  
30% minimum reflectance  
UPC/EAN, UPC/EAN with Supplementals, UCC/EAN 128, Code 39,  
Code 39 Full ASCII, Code 39 TriOptic, Code 128, Code 128 Full ASCII,  
Codabar, Interleaved 2 of 5, Discrete 2 of 5, Code 93, MSI, Code 11,  
IATA, GS1 DataBar (RSS) variants, Chinese 2 of 5  
Decode Capability  
Interfaces Supported  
RS-232; Keyboard Wedge; USB  
Product Reference Guide  
147  
Item  
Description  
User Environment  
Operating Temperature  
Storage Temperature  
Humidity  
32° to 122° F (0° to 50° C)  
-40° to 158° F (-40° to 70° C)  
5% to 95% relative humidity, non-condensing  
Drop Specifications  
Withstands multiple 5 ft./1.524 m drops to concrete.  
Immune to direct exposure of normal office and factory lighting conditions,  
as well as direct exposure to sunlight.  
Ambient Light Immunity  
Beeper Volume  
Beeper Tone  
User-selectable: three levels  
User-selectable: three tones  
Electrostatic Discharge  
Regulatory  
Conforms to 20 kV air/direct discharge and 8 kV of contact discharge.  
Electrical Safety  
UL 60950, CAN/CSA-C22.2 No. 60950, EN60950/IEC950  
FCC Part 15 Class B, ICES-003 Class B, European Union EMC Directive,  
Australian SMA, Taiwan EMC, Japan VCCI/MITI  
EMI/RFI  
IEC Class 2  
Complies with 21 CFR 1040.10 and 1040.11, except for deviation pursu-  
ant to Laser Notice 50, dated June 24, 2007.  
IEC/EN60825-1:2007  
Laser Safety  
Laser light — Do not stare into beam.  
CAUTION  
148  
QuickScan® L  
Standard Cable Pinouts  
Standard Cable Pinouts  
Figure 13 and Table 29 provide standard pinout information for the scanner’s cable.  
Figure 13. Standard Cable Pinouts  
Bottom of Scanner  
Cable  
Interface Cable Port  
Cable Strain Relief  
Pin 1  
Pin 10  
To Host  
Cable Clip (Latch)  
Product Reference Guide  
149  
The signal descriptions in Table 29 apply to the connector on the scanner and are for  
reference only.  
Table 29 Standard Cable Pinouts  
Pin  
RS-232  
Keyboard Wedge  
USB  
1
2
RTS  
nc  
nc  
Clk In  
Data In  
Ground  
nc  
Jump to Pin 5  
D+  
3
nc  
D-  
4
Ground  
RXD  
TXD  
Power  
nc  
Ground  
5
Jump to Pin 1  
6
nc  
nc  
Power  
nc  
7
Power  
Clk Out  
Data Out  
nc  
8
9
nc  
nc  
10  
CTS  
nc  
150  
QuickScan® L  
Appendix B  
Standard Defaults  
The most common configuration settings are listed in the “Default” column of the table  
below. Page references are also provided for feature descriptions and programming bar  
codes for each parameter. A column has also been provided for recording of your pre-  
ferred default settings for these same configurable features.  
Table 30. Standard Defaults  
Parameter  
General Features  
Default  
Your Setting  
Page Number  
Set Default Parameter  
Beeper Tone  
Restore Defaults  
Medium  
21  
22  
22  
23  
25  
25  
26  
26  
28  
29  
29  
30  
30  
Beeper Volume  
High  
Power Mode  
Continuous On  
Full Width  
3.0 Sec  
Scan Line Width  
Laser On Time  
Beep After Good Read  
Transmit Label ID  
Global Prefix/Suffix  
Prefix Value  
Enable  
None  
Data As Is  
7013 <CR><LF>  
7013 <CR><LF>  
Set  
Suffix Value  
FN1 Substitution Values  
Transmit “No Read” Message  
Keyboard Wedge Host Parameters  
Disable  
IBM PC/AT& IBM PC  
Compatibles1  
Keyboard Wedge Host Type  
57  
Country Types (Country Codes)  
Ignore Unknown Characters  
North American  
Send  
58  
59  
1User selection is required to configure this interface and this is the most common selection.  
Product Reference Guide  
151  
Parameter  
Default  
No Delay  
Your Setting  
Page Number  
Keystroke Delay  
60  
60  
61  
61  
62  
62  
63  
63  
63  
Intra-Keystroke Delay  
Alternate Numeric Keypad Emulation  
Caps Lock On  
Disable  
Disable  
Disable  
Disable  
No Convert  
Disable  
Disable  
Send  
Caps Lock Override  
Convert Wedge Data  
Function Key Mapping  
FN1 Substitution  
Send and Make Break  
RS-232 Host Parameters  
RS-232 Host Types  
Baud Rate  
Standard  
9600  
36  
37  
38  
39  
39  
40  
41  
43  
45  
46  
46  
47  
48  
48  
Parity Type  
None  
Stop Bit Select  
1 Stop Bit  
8-Bit  
Data Bits (ASCII Format)  
Check Receive Errors  
Hardware Handshaking  
Software Handshaking  
Host Serial Response Time-out  
RTS Line State  
Enable  
None  
None  
2 Sec  
Low RTS  
Disable  
0 msec  
Beep on <BEL>  
Intercharacter Delay  
Nixdorf Beep/LED Options  
Ignore Unknown Characters  
USB Host Parameters  
Normal Operation  
Send Bar Code  
HID Keyboard Emu-  
lation  
USB Device Type  
77  
USB Country Keyboard Types (Country  
Codes)  
North American  
No Delay  
78  
80  
USB Keystroke Delay  
1User selection is required to configure this interface and this is the most common selection.  
152  
QuickScan® L  
Parameter  
USB CAPS Lock Override  
USB Ignore Unknown Characters  
Emulate Keypad  
USB FN1 Substitution  
Function Key Mapping  
Simulated Caps Lock  
Convert Case  
Default  
Disable  
Your Setting  
Page Number  
80  
81  
81  
82  
82  
83  
83  
Send  
Disable  
Disable  
Disable  
Disable  
No Case Conversion  
UPC/EAN  
UPC-A  
Enable  
Enable  
Disable  
Enable  
Enable  
Disable  
99  
99  
UPC-E  
UPC-E1  
100  
101  
101  
101  
EAN-8/JAN 8  
EAN-13/JAN 13  
Bookland EAN  
Decode UPC/EAN/JAN Supplementals (2  
and 5 digits)  
Ignore  
7
102  
104  
Decode UPC/EAN/JAN Supplemental  
Redundancy  
Transmit UPC-A Check Digit  
Transmit UPC-E Check Digit  
Transmit UPC-E1 Check Digit  
UPC-A Preamble  
Enable  
104  
105  
105  
106  
107  
108  
109  
109  
110  
110  
Enable  
Enable  
System Character  
System Character  
System Character  
Disable  
UPC-E Preamble  
UPC-E1 Preamble  
Convert UPC-E to A  
Convert UPC-E1 to A  
EAN-8/JAN-8 Extend  
UCC Coupon Extended Code  
Code 128  
Disable  
Disable  
Disable  
Code 128  
Enable  
111  
1User selection is required to configure this interface and this is the most common selection.  
Product Reference Guide  
153  
Parameter  
Default  
Your Setting  
Page Number  
111  
UCC/EAN-128  
Enable  
Enable  
ISBT 128 (non-concatenated)  
Code 39  
112  
Code 39  
Enable  
112  
113  
Trioptic Code 39  
Disable  
Disable  
Convert Code 39 to Code 32 (Italian Phar-  
macy Code)  
113  
Code 32 Prefix  
Disable  
2 to 55  
Disable  
Disable  
Disable  
Disable  
114  
114  
116  
116  
117  
118  
Set Length(s) for Code 39  
Code 39 Check Digit Verification  
Transmit Code 39 Check Digit  
Code 39 Full ASCII Conversion  
Buffer Code 39  
Code 93  
Code 93  
Disable  
4 to 55  
120  
121  
Set Length(s) for Code 93  
Code 11  
Code 11  
Disable  
4 to 55  
Disable  
Disable  
122  
123  
125  
126  
Set Lengths for Code 11  
Code 11 Check Digit Verification  
Transmit Code 11 Check Digit(s)  
Interleaved 2 of 5 (ITF)  
Interleaved 2 of 5 (ITF)  
Set Lengths for I 2 of 5  
I 2 of 5 Check Digit Verification  
Transmit I 2 of 5 Check Digit  
Convert I 2 of 5 to EAN 13  
Discrete 2 of 5 (DTF)  
Discrete 2 of 5  
Enable  
14  
126  
127  
129  
129  
130  
Disable  
Disable  
Disable  
Disable  
12  
130  
131  
Set Length(s) for D 2 of 5  
1User selection is required to configure this interface and this is the most common selection.  
154  
QuickScan® L  
Parameter  
Default  
Your Setting  
Page Number  
Chinese 2 of 5  
Enable/Disable Chinese 2 of 5  
Codabar (NW - 7)  
Disable  
132  
Codabar  
Disable  
5 to 55  
Disable  
Disable  
133  
133  
135  
136  
Set Lengths for Codabar  
CLSI Editing  
NOTIS Editing  
MSI  
MSI  
Disable  
136  
137  
138  
139  
139  
Set Length(s) for MSI  
MSI Check Digits  
2 to 55  
One  
Transmit MSI Check Digit  
MSI Check Digit Algorithm  
GS1 DataBar (RSS)  
DataBar Omnidirectional (RSS -14)  
DataBar Limited  
Disable  
Mod 10/Mod 10  
Disable  
Disable  
Disable  
Disable  
140  
140  
140  
141  
DataBar Expanded  
Convert DataBar to UPC/EAN  
Symbology - Specific Security Levels  
Redundancy Level  
Security Levels  
1
142  
144  
145  
0
Bi-directional Redundancy  
Disable  
1User selection is required to configure this interface and this is the most common selection.  
Product Reference Guide  
155  
NOTES  
156  
QuickScan® L  
Appendix C  
Programming Reference  
Datalogic Label ID Identifiers  
Table 31. Symbology Characters  
Code Character  
Code Type  
A
B
C
D
E
F
UPC/EAN  
Code 39, Code 39 Full ASCII, Code 32  
Codabar  
Code 128, ISBT 128  
Code 93  
Interleaved 2 of 5  
Discrete 2 of 5, or Discrete 2 of 5 IATA  
Code 11  
G
H
J
MSI  
K
L
UCC/EAN-128  
Bookland EAN  
M
N
R
Trioptic Code 39  
Coupon Code  
GS1 DataBar (RSS) Family  
AIM Label ID Identifiers  
Each AIM label ID Identifier contains the three-character string ]cm where:  
]=Flag Character (ASCII 93)  
c=Code Character (see Table 32)  
m=Modifier Character (see Table 33)  
Product Reference Guide  
157  
Table 32. Aim Label ID Characters  
Code Character  
A
Code Type  
Code 39, Code 39 Full ASCII, Code 32  
Code 128 (all variants), Coupon (Code 128  
portion)  
C
E
e
UPC/EAN, Coupon (UPC portion)  
GS1 DataBar (RSS) Family  
Codabar  
F
G
H
I
Code 93  
Code 11  
Interleaved 2 of 5  
MSI  
M
S
X
D2 of 5, IATA 2 of 5  
Bookland EAN, Code 39 Trioptic  
The modifier character is the sum of the applicable option values based on Table 33.  
Table 33. Modifier Characters  
Code Type  
Option Value  
Option  
0
1
3
4
No check character or Full ASCII processing.  
Reader has checked one check character.  
Reader has checked and stripped check character.  
Reader has performed Full ASCII character conversion.  
Code 39  
Reader has performed Full ASCII character conversion and  
checked one check character.  
5
7
Reader has performed Full ASCII character conversion and  
checked and stripped check character.  
Example: A Full ASCII bar code with check character W, A+I+MI+DW, is transmitted as ]A7AIMID  
where 7 = (3+4).  
0
No option specified at this time. Always transmit 0.  
Trioptic Code 39  
Example: A Trioptic bar code 412356 is transmitted as ]X0412356  
158  
QuickScan® L  
AIM Label ID Identifiers  
Table 33. Modifier Characters (Continued)  
Code Type  
Option Value  
Option  
0
1
2
Standard data packet, no Function code 1 in first bar code position.  
Function code 1 in first bar code character position.  
Function code 1 in second bar code character position.  
FNC1  
Code 128  
Example: A Code (EAN) 128 bar code with Function 1 character  
in the first position, AIMID is  
transmitted as ]C1AIMID  
0
1
3
No check digit processing.  
Reader has validated check digit.  
I 2 of 5  
Reader has validated and stripped check digit.  
Example: An I 2 of 5 bar code without check digit, 4123, is transmitted as ]I04123  
0
1
3
No check digit processing.  
Reader has checked check digit.  
Codabar  
Reader has stripped check digit before transmission.  
Example: A Codabar bar code without check digit, 4123, is transmitted as ]F04123  
No options specified at this time. Always transmit 0.  
Example: A Code 93 bar code 012345678905 is transmitted as ]G0012345678905  
0
Code 93  
MSI  
0
1
Check digits are sent.  
No check digit is sent.  
Example: An MSI bar code 4123, with a single check digit checked, is transmitted as ]M14123  
No options specified at this time. Always transmit 0.  
Example: A D 2 of 5 bar code 4123, is transmitted as ]S04123  
0
D 2 of 5  
Standard packet in full EAN country code format, which is 13 digits  
for UPC-A and UPC-E (not including supplemental data).  
0
1
2
4
Two-digit supplement data only.  
UPC/EAN  
Five-digit supplement data only.  
EAN-8 data packet.  
Example: A UPC-A bar code 012345678905 is transmitted as ]E00012345678905  
No options specified at this time. Always transmit 0.  
Example: A Bookland EAN bar code 123456789X is transmitted as ]X0123456789X  
0
Bookland EAN  
Product Reference Guide  
159  
Table 33. Modifier Characters (Continued)  
Code Type  
Option Value  
Option  
0
1
3
Single check digit  
Two check digits  
Code 11  
Check characters validated but not transmitted.  
No option specified at this time. Always transmit 0. DataBar Omnidi-  
rectional (RSS-14) and DataBar Limited transmit with an Applica-  
tion Identifier “01”.Note: In UCC/EAN-128 emulation mode, DataBar  
is transmitted using Code 128 rules (i.e., ]C1).  
GS1 DataBar (RSS)  
Family  
Example: A DataBar Omnidirectional bar code 100123456788902 is transmitted as  
]e001100123456788902.  
160  
QuickScan® L  
Appendix D  
Sample Bar Codes  
The sample bar codes in this appendix are typical representations for their symbology  
types.  
UPC/EAN  
UPC-A, 100%  
0
12345 67890  
5
EAN-13, 100%  
3
4
56789
 
012340  
Code 128  
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4  
Product Reference Guide  
161  
Sample Bar Codes — continued  
Code 39  
123ABC  
Code 93  
123456-9$  
Code 11  
123456  
Interleaved 2 of 5  
1234567890  
162  
QuickScan® L  
Discrete 2 of 5 (DTF)  
Discrete 2 of 5 (DTF)  
1 2 3 2 4 6 5 7  
Chinese 2 of 5  
12345678902  
Codabar  
A13579B  
MSI  
24681355  
Product Reference Guide  
163  
DataBar (RSS)  
DataBar variants must be enabled to read the bar codes below (see GS1  
DataBar (RSS) on page 140).  
NOTE  
10293847560192837465019283746029478450366523  
(DataBar Expanded Stacked)  
1234890hjio9900mnb  
(DataBar Expanded)  
08672345650916  
(DataBar Limited)  
DataBar Omnidirectional  
55432198673467  
(DataBar Omnidirectional Truncated)  
90876523412674  
(DataBar Omnidirectional Stacked)  
78123465709811  
(DataBar Stacked Omnidirectional)  
164  
QuickScan® L  
Appendix E  
Keypad  
Use the bar codes in this appendix to enter numbers as you would select digits/characters  
from a keypad.  
0
1
2
3
4
5
Product Reference Guide  
165  
6
7
8
9
Cancel  
To correct an error or change a selection, scan the bar code below.  
Cancel  
166  
QuickScan® L  
Appendix F  
ASCII Character Sets  
Table 34. ASCII Value - Code 39 Encode - Keystroke  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1000  
1001  
1002  
1003  
1004  
1005  
1006  
1007  
1008  
1009  
1010  
1011  
1012  
1013  
1014  
1015  
1016  
1017  
1018  
1019  
1020  
1021  
%U  
$A  
$B  
$C  
$D  
$E  
$F  
$G  
$H  
$I  
CTRL 2  
CTRL A  
CTRL B  
CTRL C  
CTRL D  
CTRL E  
CTRL F  
CTRL G  
CTRL H/BACKSPACE1  
CTRL I/HORIZONTAL TAB1  
CTRL J  
$J  
$K  
$L  
CTRL K  
CTRL L  
CTRL M/ENTER1  
CTRL N  
$M  
$N  
$O  
$P  
$Q  
$R  
$S  
$T  
$U  
CTRL O  
CTRL P  
CTRL Q  
CTRL R  
CTRL S  
CTRL T  
CTRL U  
Product Reference Guide  
167  
Table 34. ASCII Value - Code 39 Encode - Keystroke (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1022  
1023  
1024  
1025  
1026  
1027  
1028  
1029  
1030  
1031  
1032  
1033  
1034  
1035  
1036  
1037  
1038  
1039  
1040  
1041  
1042  
1043  
1044  
1045  
1046  
1047  
1048  
1049  
1050  
1051  
$V  
$W  
$X  
$Y  
$Z  
%A  
%B  
%C  
%D  
%E  
Space  
/A  
CTRL V  
CTRL W  
CTRL X  
CTRL Y  
CTRL Z  
CTRL [  
CTRL \  
CTRL ]  
CTRL 6  
CTRL -  
Space  
!
/B  
/C  
/D  
/E  
#
?
%
&
/F  
/G  
/H  
/I  
(
)
/J  
*
/K  
+
,
/L  
-
-
.
.
/o  
/
0
0
1
2
3
1
2
3
168  
QuickScan® L  
Table 34. ASCII Value - Code 39 Encode - Keystroke (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1052  
1053  
1054  
1055  
1056  
1057  
1058  
1059  
1060  
1061  
1062  
1063  
1064  
1065  
1066  
1067  
1068  
1069  
1070  
1071  
1072  
1073  
1074  
1075  
1076  
1077  
1078  
1079  
1080  
1081  
4
5
4
5
6
6
7
7
8
8
9
9
/Z  
%F  
%G  
%H  
%I  
%J  
%V  
A
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
B
C
D
E
F
G
H
I
J
J
K
K
L
L
M
N
M
N
O
P
Q
O
P
Q
Product Reference Guide  
169  
Table 34. ASCII Value - Code 39 Encode - Keystroke (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1082  
1083  
1084  
1085  
1086  
1087  
1088  
1089  
1090  
1091  
1092  
1093  
1094  
1095  
1096  
1097  
1098  
1099  
1100  
1101  
1102  
1103  
1104  
1105  
1106  
1107  
1108  
1109  
1110  
1111  
R
S
R
S
T
U
V
W
X
Y
Z
[
T
U
V
W
X
Y
Z
%K  
%L  
%M  
%N  
%O  
%W  
+A  
+B  
+C  
+D  
+E  
+F  
+G  
+H  
+I  
\
]
^
_
a
b
c
d
e
f
g
h
i
+J  
+K  
+L  
+M  
+N  
+O  
j
k
l
m
n
o
170  
QuickScan® L  
Table 34. ASCII Value - Code 39 Encode - Keystroke (Continued)  
Full ASCII  
Code 39 Encode Character  
ASCII Value  
Keystroke  
1112  
1113  
1114  
1115  
1116  
1117  
1118  
1119  
1120  
1121  
1122  
1123  
1124  
1125  
1126  
+P  
+Q  
+R  
+S  
p
q
r
s
t
+T  
+U  
+V  
u
v
w
x
y
z
{
+W  
+X  
+Y  
+Z  
%P  
%Q  
%R  
%S  
I
}
~
The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the  
unbolded keystroke is sent.  
Table 35. ALT Key Standard Defaults  
ALT Keys  
2064  
2065  
2066  
2067  
2068  
2069  
2070  
2071  
2072  
2073  
Keystroke  
ALT 2  
ALT A  
ALT B  
ALT C  
ALT D  
ALT E  
ALT F  
ALT G  
ALT H  
ALT I  
Product Reference Guide  
171  
Table 35. ALT Key Standard Defaults (Continued)  
ALT Keys  
2074  
2075  
2076  
2077  
2078  
2079  
2080  
2081  
2082  
2083  
2084  
2085  
2086  
2087  
2088  
2089  
2090  
Keystroke  
ALT J  
ALT K  
ALT L  
ALT M  
ALT N  
ALT O  
ALT P  
ALT Q  
ALT R  
ALT S  
ALT T  
ALT U  
ALT V  
ALT W  
ALT X  
ALT Y  
ALT Z  
Table 36. Miscellaneous Key Standard Defaults  
Misc. Key  
3001  
Keystroke  
PA 1  
3002  
PA 2  
3003  
CMD 1  
CMD 2  
CMD 3  
CMD 4  
CMD 5  
CMD 6  
CMD 7  
3004  
3005  
3006  
3007  
3008  
3009  
172  
QuickScan® L  
Table 36. Miscellaneous Key Standard Defaults (Continued)  
Misc. Key  
3010  
Keystroke  
CMD 8  
3011  
CMD 9  
3012  
CMD 10  
CMD 11  
CMD 12  
CMD 13  
CMD 14  
3013  
3014  
3015  
3016  
Table 37. GUI Shift Keys  
GUI Shift Keys  
The AppleiMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to  
the left of the left ALT key, and to the right of the right ALT key.  
Other Value  
3048  
3049  
3050  
3051  
3052  
3053  
3054  
3055  
3056  
3057  
3065  
3066  
3067  
3068  
3069  
3070  
3071  
3072  
Keystroke  
GUI 0  
GUI 1  
GUI 2  
GUI 3  
GUI 4  
GUI 5  
GUI 6  
GUI 7  
GUI 8  
GUI 9  
GUI A  
GUI B  
GUI C  
GUI D  
GUI E  
GUI F  
GUI G  
GUI H  
Product Reference Guide  
173  
Table 37. GUI Shift Keys (Continued)  
GUI Shift Keys  
The AppleiMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to  
the left of the left ALT key, and to the right of the right ALT key.  
Other Value  
3073  
3074  
3075  
3076  
3077  
3078  
3079  
3080  
3081  
3082  
3083  
3084  
3085  
3086  
3087  
3088  
3089  
3090  
Keystroke  
GUI I  
GUI J  
GUI K  
GUI L  
GUI M  
GUI N  
GUI O  
GUI P  
GUI Q  
GUI R  
GUI S  
GUI T  
GUI U  
GUI V  
GUI W  
GUI X  
GUI Y  
GUI Z  
Table 38. PF Key Standard Default Table  
PF Keys  
4001  
4002  
4003  
4004  
4005  
4006  
4007  
Keystroke  
PF 1  
PF 2  
PF 3  
PF 4  
PF 5  
PF 6  
PF 7  
174  
QuickScan® L  
Table 38. PF Key Standard Default Table (Continued)  
PF Keys  
4008  
4009  
4010  
4011  
4012  
4013  
4014  
4015  
4016  
Keystroke  
PF 8  
PF 9  
PF 10  
PF 11  
PF 12  
PF 13  
PF 14  
PF 15  
PF 16  
Table 39. F key Standard Default Table  
F Keys  
5001  
5002  
5003  
5004  
5005  
5006  
5007  
5008  
5009  
5010  
5011  
5012  
5013  
5014  
5015  
5016  
5017  
5018  
Keystroke  
F 1  
F 2  
F 3  
F 4  
F 5  
F 6  
F 7  
F 8  
F 9  
F 10  
F 11  
F 12  
F 13  
F 14  
F 15  
F 16  
F 17  
F 18  
Product Reference Guide  
175  
Table 39. F key Standard Default Table (Continued)  
F Keys  
5019  
5020  
5021  
5022  
5023  
5024  
Keystroke  
F 19  
F 20  
F 21  
F 22  
F 23  
F 24  
Table 40. Numeric Key Standard Default Table  
Numeric Keypad  
6042  
Keystroke  
*
6043  
+
6044  
Undefined  
6045  
-
6046  
.
6047  
/
6048  
0
6049  
1
6050  
2
6051  
3
6052  
4
6053  
5
6054  
6
6055  
7
6056  
8
9
6057  
6058  
Enter  
Num Lock  
6059  
176  
QuickScan® L  
Table 41. Extended Keypad Standard Default Table  
Extended Keypad  
7001  
Keystroke  
Break  
Delete  
7002  
7003  
Pg Up  
7004  
End  
7005  
Pg Dn  
7006  
Pause  
7007  
Scroll Lock  
Backspace  
Tab  
7008  
7009  
7010  
Print Screen  
Insert  
7011  
7012  
Home  
7013  
Enter  
7014  
Escape  
Up Arrow  
Dn Arrow  
Left Arrow  
Right Arrow  
7015  
7016  
7017  
7018  
Product Reference Guide  
177  
NOTES  
178  
QuickScan® L  
Appendix G  
RS-232 Host Commands  
The RS-232 interface will accept commands from a POS host. The available commands  
are:  
Disable Scanner  
Enable Scanner  
Reset Scanner  
Beep Good Read Tone  
Force Good Read Beep  
Disable Scanner Command (ASCII 'D') — places the scanner in an operational mode  
in which the scanner does not accept barcode data input from the scan optics. The Laser  
is disabled while the scanner is disabled. Once the command is accepted and implement-  
ed by the scanner, the green indicator LED flashes to indicate the disabled status. This  
state is cleared if:  
1) an Enable Command is sent  
2) a Reset Command is sent  
3) power is cycled to the scanner.  
Enable Scanner Command (ASCII 'E') — places the scanner in an normal operational  
mode in which the scanner will accept barcode label data input from the scan optics.  
Reset Scanner Command (ASCII 'R') — performs a scanner reset operation. Any bar-  
code data the scanner may be holding in buffers is discarded.  
Good Read Beep Command (ASCII 'B') — causes the scanner to sound one Good  
Read Beep tone if scanner and Good Decode Beep are both enabled.  
Force Beep Command (Hex '01') — forces the scanner's beeper to sound one Good  
Read Beep tone regardless of, and overriding, any other current scanner setting.  
Product Reference Guide  
179  
NOTES  
180  
QuickScan® L  
Index  
Nixdorf Beep/LED options 48  
A
RTS line state 46  
stop bit select 39  
ADF  
invalid rule 15  
RS-232 parameters  
parity 38  
symbologies  
transmit error 10, 15  
advanced data formatting 10, 15  
ASCII values  
bi-directional redundancy 145  
bookland EAN, enable/disable  
101  
Chinese 2 of 5, enable/disable  
132  
keyboard wedge 64  
RS-232 49  
USB 84  
codabar CLSI editing 135  
codabar lengths 133, 134  
codabar NOTIS editing 136  
codabar, enable/disable 133  
code 11 check digit verification  
125  
code 11 lengths 123  
code 11, transmit check digits  
126  
code 128, enable/disable 111  
code 39  
B
bar code defaults  
keyboard wedge 56  
RS-232 33  
symbologies 96  
USB 76  
bar codes  
cancel 166  
keyboard wedge  
alternate numeric keypad emu-  
lation 61  
transmit buffer 119  
caps lock on 61  
code 39 buffering 118  
code 39 check digit verification  
116  
caps lock override 62  
country keyboard types (country  
codes) 58  
code 39 full ASCII conversion 117  
code 39 lengths 114  
code 39 transmit check digit 116  
code 39, enable/disable 112  
code 93 lengths 121  
code 93, enable/disable 120  
convert UPC-E to UPC-A 109  
convert UPC-E1 to UPC-A 109  
discrete 2 of 5 lengths 131  
discrete 2 of 5, enable/disable  
130  
EAN-13/EAN-8, enable/disable  
101  
EAN-8/JAN-8 extend 110  
I 2 of 5 check digit verification  
129  
host types 57  
ignore unknown characters 59  
intra-keystroke delay 60  
keystroke delay 60  
numeric bar codes 166  
RS-232  
baud rate 37  
beep on 46  
check receive errors 40  
data bits 39  
hardware handshaking 41  
host serial response time-out 45  
host types 36  
ignore unknown characters 48  
intercharacter delay 47  
I 2 of 5 convert to EAN-13 130  
I 2 of 5 lengths 127  
I 2 of 5 transmit check digit 129  
I 2 of 5, enable/disable 126  
intercharacter gap 146  
code 128 bar codes 111  
code 39 bar codes 112  
code 93 bar codes 120  
code identifiers  
AIM code IDs 157  
ISBT 128, enable/disable 112  
MSI check digit algorithm 139  
MSI check digits 138  
D
MSI lengths 137, 138  
DataBar, convert to UPC/EAN 141  
DataBar, enable/disable 140  
default parameters  
keyboard wedge 56  
RS-232 33  
MSI transmit check digits 139  
MSI, enable/disable 136  
redundancy levels 142  
RSS, convert to UPC/EAN 141  
RSS, enable/disable 140  
security levels 144  
symbologies 96  
USB 76  
bi-directional redundancy 145  
supplementals 102  
Depth of Field Chart 14  
discrete 2 of 5 bar codes 130  
DTF bar codes 130  
trioptic code 39, enable/disable  
113  
UCC coupon extended code 110  
UCC/EAN-128,  
enable/disable E  
111  
error indications  
ack/nak 43  
UPC/EAN/JAN supplemental re-  
dundancy 104  
ADF 10, 15  
UPC-A preamble 106  
enq 43  
UPC-A transmit check digit 104  
UPC-A/UPC-E, enable/disable 99  
UPC-E preamble 107  
format 10, 16  
input 10, 15  
RS-232 10, 15  
UPC-E transmit check digit 105  
UPC-E1 preamble 108  
UPC-E1 transmit check digit 105  
UPC-E1, enable/disable 100  
RS-232 transmission 41  
symbologies 95  
transmission 10, 11, 15, 45  
unknown characters 48, 59, 81  
xon/xoff 43  
USB  
caps lock override 80  
country keyboard types 78  
device type 77  
F
keystroke delay 80  
Field, Depth of 14  
unknown characters 81  
bar codes RS-232  
software handshaking 43  
G
Getting Started 1, 5, 9, 15, 19, 55  
C
character set 49, 64, 84  
Chinese 2 of 5 bar codes 132  
codabar bar codes 133  
code 11 bar codes 122  
H
Host Commands 179  
host types  
182  
QuickScan® L  
keyboard wedge 57  
RS-232 36  
USB 77  
S
sample bar codes  
code 128 161  
code 39 162  
interleaved 2 of 5 162  
UPC/EAN 161  
I
intercharacter gap 146  
scanning  
interleaved 2 of 5 bar codes 126  
errors 59, 81  
symbologies sequence example 95  
security level bar codes  
bi-directional redundancy 145  
security levels 142, 144  
Serial Output 150  
K
keyboard wedge connection 55  
keyboard wedge defaults 56  
keyboard wedge parameters 57  
setup  
connecting a USB interface 75  
connecting an RS-232 interface 32  
connecting keyboard wedge inter-  
face 55  
M
MSI bar codes 136  
Standard 149  
Standard Cable Pinouts 149  
symbologies defaults 96  
N
NW - 7 133  
U
P
UPC/EAN bar codes 99  
USB connection 75  
USB defaults 76  
parameter defaults  
keyboard wedge 56  
RS-232 33  
USB parameters 77  
symbologies 96  
USB 76  
parameters  
keyboard wedge 57  
RS-232 33  
symbologies 96  
USB 77  
Product Specifications 147  
R
RS-232 connection 32  
RS-232 defaults 33  
RS-232 parameters 33  
RSS bar codes  
reduced space symbology 140  
Product Reference Guide  
183  
184  
QuickScan® L  
Australia  
Datalogic Scanning Pty Ltd  
Japan  
Datalogic Scanning KK  
Telephone: [61] (2) 9870 3200  
Telephone: 81 (0)3 3491 6761  
France and Benelux  
Datalogic Scanning Sarl  
Latin America  
Datalogic Scanning, Inc  
Telephone: [33].01.64.86.71.00  
Telephone: (305) 591-3222  
Germany  
Datalogic Scanning GmbH  
Telephone: 49 (0) 61 51/93 58-0  
Singapore  
Datalogic Scanning Singapore PTE LTD  
Telephone: (65) 6435-1311  
India  
Datalogic Scanning India  
Telephone: 91- 22 - 64504739  
Spain and Portugal  
Datalogic Scanning Sarl Sucursal en España  
Telephone: 34 91 746 28 60  
Italy  
Datalogic Scanning SpA  
United Kingdom  
Datalogic Scanning LTD  
Telephone: [39] (0) 39/62903.1  
Telephone: 44 (0) 1923 809500  
www.scanning.datalogic.com  
Datalogic Scanning, Inc.  
959 Terry Street  
Eugene, OR 97402  
Telephone: (541) 683-5700  
Fax: (541) 345-7140  
© 2007-2008 Datalogic Scanning, Inc. R44-2902 (Rev. C)  
9/08  

Allstar Products Group LLC Automobile Accessories Twist R Plus Class I Vehicular Swing Gate Operator User Manual
Amana Quiet Zone 7M11TA User Manual
Blizzard Ski Automobile Accessories 810SS User Manual
Burley HQ8445 User Manual
Canon PIXMA MX850 Series User Manual
Carrier 48TM007 012 User Manual
Friedrich MW09Y3FM User Manual
Fujitsu AOU15RLQ User Manual
Graco Baby Monitor 2795 User Manual
Graco LISTEN & #39;N TALK 2770 User Manual