Model No. 831.297572
Serial No.
Write the serial number in the space
above for future reference.
Serial Number Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
THE TREADMILL on page 17.) You must be
able to safely lift 45 pounds (20 kg) in order
to raise, lower, or move the treadmill.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and tighten all parts of the treadmill
every three months.
16. To reduce the possibility of the treadmill over-
heating, do not operate the treadmill continu-
ously for longer than one hour.
22. Never insert any object into any opening.
17. The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
23. The roller guards must be 1/8 inch from the
rear roller. Remove the key and adjust the
roller guards, if necessary.
24. Always unplug the power cord before per-
forming the maintenance and adjustment pro-
cedures described in this manual. Never re-
move the motor hood unless instructed to do
so by an authorized service representative.
Servicing other than the procedures in this
manual should be performed by an authorized
service representative only.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the ÒoffÓ position when the treadmill is not in
use. (See the drawing on page 4 for the loca-
tion of the on/off switch.)
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
SAVE THESE INSTRUCTIONS
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
The decals shown below have been placed on your treadmill. If a decal is missing, or if it is not legible,
please call our toll-free HELPLINE to order a free replacement decal (see ORDERING REPLACEMENT
PARTS on the back cover). Apply the decal in the location shown.
IMPORTANT: Incline must be set at
lowest level before
folding treadmill into
storage position.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the IMAGE¨ 10.6Q treadmill.
The IMAGE¨ 10.6Q treadmill combines advanced tech-
nology with innovative design to let you enjoy an effec-
tive form of cardiovascular exercise in the convenience
and privacy of your home. And when youÕre not exer-
cising, the unique IMAGE¨ 10.6Q can be folded up, re-
quiring less than half the floor space of other treadmills.
1-800-736-6879, Monday through Saturday, 7 a.m.
until 7 p.m. Central Time (excluding holidays). To help
us assist you, please note the product model number
and serial number before calling. The model number of
the treadmill is 831.297572. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing the manual, please call our toll-free HELPLINE at
Before reading further, please review the drawing
below and familiarize yourself with the parts that are la-
beled.
Console
Reading Rack
Water Bottle
Holder (Bottle
not included)
Accessory Tray
Handrail
Key/Clip
Upright
Lock Knob
On/Off
Switch
Walking Belt
Circuit
Breaker
Foot Rail
Power Cord
RIGHT SIDE
Rear Roller
Adjustment Bolt
Cushion Knob
BACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. No tools are required for assembly.
1. With the help of a second person, carefully raise the
Uprights (115) until the treadmill is in the position shown.
1
115
2. Press the Lock Knob Sleeve (100) into the left Upright
(115).
2
115
Remove the Lock Knob (99) from the Lock Pin (103).
Make sure that the Lock Pin Collar (102) and the Spring
(101) are on the Lock Pin. Insert the Lock Pin into the left
Upright (115) and tighten the Lock Knob onto the Lock
Pin.
101
102
99
103
100
3. Remove the backing from the Adhesive Clip (94). Press
the Adhesive Clip onto the base of the Uprights (115) in
the indicated location. Press the Allen Wrench (95) into
the Adhesive Clip.
3
115
95
94
4. Make sure that all parts are tightened before you use the treadmill. Place a mat under the treadmill to
protect the floor or carpet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
use, it may remain activated longer than necessary,
draining the battery prematurely.
The heart rate monitor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap
through one of the holes in the sensor unit. Press the
end of the sensor unit under the buckle on the chest
strap. The tab should be almost flush with the front of
the sensor unit.
¥ Store the heart rate monitor in a warm, dry place.
Do not store the heart rate monitor in a plastic bag
or other container that may trap moisture.
¥ Do not expose the heart rate monitor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122¡ Fahrenheit (50¡
Celsius) or below 14¡ Fahrenheit (-10¡ Celsius).
¥ Do not excessively bend or stretch the sensor unit
when using or storing the heart rate monitor.
Chest Strap
Tabs
¥ Clean the sensor unit using a damp clothÑnever
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Buckle
HEART RATE MONITOR TROUBLE-SHOOTING
The instructions on the following pages explain
how the heart rate monitor is used with the console.
If the letters ÒPLSÓ appear in the PULSE/CALORIES
display or if the displayed heart rate is excessively
high or low, try the steps below.
Tab
Sensor Unit
Next, wrap the
heart rate moni-
tor around your
chest and
attach the other
end of the chest
strap to the sen-
sor unit. Adjust
the length of the
chest strap, if
¥ Make sure that the heart rate monitor is under your
clothing, tight against your skin, and as high under
the pectoral muscles or breasts as is comfortable.
The logo on the sensor unit must be facing forward
and be right-side-up. Note: If the heart rate monitor
does not function when positioned as described, try
moving it slightly lower or higher on your chest.
necessary. The
heart rate moni-
tor should be under your clothing, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
¥ Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
¥ As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within armÕs length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side.
The electrode areas are the areas covered by shallow
ridges. Using saline solution such as saliva or contact
lens solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
¥ The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
HEART RATE MONITOR CARE AND MAINTENANCE
¥ Thoroughly dry the heart rate monitor after each
use. The heart rate monitor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the heart rate monitor shuts off
when it is removed and the electrode areas are
dried. If the heart rate monitor is not dried after each
¥ The operation of the heart rate monitor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
¥ The CR2032 battery may need to be replaced.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
1
HOW TO PLUG IN THE POWER CORD
Grounded Outlet Box
Surge Suppressor
Grounding Pin
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
Grounding Pin
Grounded Outlet
Grounding Plug
installed by a qualified electrician.
2
Grounded Outlet Box
Adapter
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Surge Suppressor
Lug
Metal Screw
Surge suppressors are sold at most hardware stores
and department stores. Use only a single-outlet surge
suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must
have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
B
A
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Note: If there is a thin sheet of clear plastic
on the face of the console, remove it.
FEATURES OF THE CONSOLE
CAUTION:To reduce the risk of
serious injury, read the following precautions
before operating the console.
The treadmill console offers an impressive array of
features designed to make your workouts more effective.
When the console is in the manual mode, the speed and
incline of the treadmill can be changed with a touch of a
button. As you exercise, the console will display instant
exercise feedbackÑyou can watch your progress on the
LED Òtrack,Ó while the four displays show your heart rate,
the number of calories burned, the incline, workout time,
speed, pace, distance, and laps completed.
¥ Do not stand on the walking belt when
turning on the power or starting the
walking belt.
¥ Always wear the clip (see part ÒOÓ in the
drawing above) while operating the tread-
mill. If the key is pulled from the console,
the walking belt will stop.
Eight preset programs are also offered: three incline pro-
grams automatically control the incline of the treadmill as
they guide you through effective workouts; three speed
programs automatically control the speed of the treadmill;
and two pulse driven programs automatically control the
speed and the incline of the treadmill to keep your heart
rate within a predetermined range during your workouts.
¥ The treadmill is capable of high speeds.
Adjust the speed in small increments.
¥ The heart rate monitor is not a medical de-
vice. Various factors may affect the accu-
racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.
The console also features two custom programs that
allow you to create your own workout programs and store
them in the consoleÕs memory for future use.
¥ If you have heart problems, or if you are
over 60 years of age and have been inac-
tive, do not use the two pulse driven pro-
grams. If you are taking medication regu-
larly, consult your physician to find
whether the medication will affect your
exercise heart rate.
To use the manual mode, follow the steps beginning on
page 10. To use an incline program or a speed pro-
gram, see page 12. To use a pulse driven program, see
page 13. To create a custom program, see page 14. To
use a custom program, see page 15.
Note: The console can display speed and distance in
either miles or kilometers (see SPEED/PACE DISPLAY
on page 11). For simplicity, all instructions in this section
refer to miles.
¥ To reduce the risk of electric shock, keep
the console dry, avoid spilling liquids on
the console, and use only a sealed water
bottle.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
K. SET WEIGHT buttonsÑThese buttons are used to
enter your weight into the console.
Refer to the drawing on the opposite page.
L. SET AGE buttonsÑThese buttons are used to enter
your age into the console.
A. Workout profilesÑThese profiles show how the
incline of the treadmill will change during incline pro-
grams, how the speed will change during speed pro-
grams, and how your heart rate will change
during pulse driven programs.
M. INCLINE buttonsÑThese buttons are used to
change the incline of the treadmill. The incline range
is 0% to 12%. Note: The incline can be adjusted
only while the walking belt is moving.
B. Mode indicatorsÑThese indicators show whether
the manual mode is selected or whether one of the
eight preset programs is selected.
N. START buttonÑThis button is used to start the
walking belt when the manual mode, a preset
program, or a custom program is selected.
C. PULSE/CALORIES displayÑThis display shows both
your heart rate (if the heart rate monitor is worn) and
the approximate number of calories you have
O. Key with clipÑThe key turns the console on and off.
The clip is worn on the waistband of your clothes.
burned. The display will alternate between one num-
ber and the other every seven seconds. This display
is also used to enter your weight into the console.
P. SPEED buttonsÑThese buttons control the speed
of the walking belt. The speed range is 0.5 mph to
12 mph. Note: When the START button is pressed,
the walking belt will begin to move at 1.0 mph.
D. INCLINE/TIME displayÑThis display shows both the
incline of the treadmill and the elapsed time. (If a
preset program or a custom program is selected, the
display will show the time remaining in the program.)
The display will alternate between one number and
the other every seven seconds. This display is also
used to enter your age into the console.
Q. STOP buttonÑThis button is used to pause or stop
the walking belt when the manual mode, a preset
program, or a custom program is selected.
HOW TO TURN ON THE POWER
E. LED matrixÑWhen the manual mode is selected, this
matrix shows your progress on an LED track. When a
preset program or a custom program is selected, the
matrix shows the programÕs workout profile.
Plug in the power cord (see page 7). All displays
and indicators on the console will flash once and
then darken. Note: If the key is in the console when
the power cord is plugged in, the letters ÒPOÓ will
flash in the SPEED/PACE display. If this occurs,
remove the key.
1
F. SPEED/PACE displayÑThis display shows both the
speed of the walking belt and your current pace
(minutes per mile). The display will alternate between
one number and the other every seven seconds.
Make sure that the
on/off switch
2
located on the
front of the tread-
OFF
G. DISTANCE/LAP displayÑThis display shows both
the distance you have walked and the number of
laps you have completed (one lap equals 1/4 mile).
The display will alternate between one number and
the other every seven seconds.
ON
mill is in the ÒonÓ
position.
Stand on the foot
rails of the tread-
mill and insert the
key into the con-
3
H. CUSTOM PROGRAM buttonsÑThese buttons are
used to select custom programs 1 and 2.
I. RECORD buttonÑThis button is used to create
custom programs.
sole. After a mo-
ment, the MAN-
UAL indicator will
light, the letters
J. PROGRAM SELECT buttonÑThis button is used to
select the manual mode and the eight preset pro-
grams. Note: If the walking belt is moving when the
SELECT PROGRAM button is pressed, the walking
belt will slow to a stop and the displays will be reset.
In addition, the treadmill may automatically adjust to
the lowest incline level.
ÒLbSÓ will appear in the PULSE/CALORIES dis-
play, the letters ÒAGEÓ will appear in the INCLINE/
TIME display, and the LED track in the center of
the console will light. Every few seconds, the words
ÒPRESS STARTÓ will scroll across the LED matrix.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Put on the heart rate monitor if desired.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
4
5
For the PULSE/CALORIES display to show your
heart rate, the heart rate monitor must be worn. To
put on the heart rate monitor, see HOW TO USE
THE HEART RATE MONITOR on page 6.
1
See HOW TO TURN ON THE POWER on page 9.
Note: When you are familiar with the operation of
the console, you may go directly to step 5 if desired.
The first time you use the console, please read and
follow all steps.
Press the START button.
Press the START button to start the walking belt.
The LED track in the center of the console will
disappear in a counterclockwise direction. One
flashing indicator will then re-appear and the
walking belt will begin to move at 1.0 mph. Hold the
handrails and step onto the walking belt.
Select the MANUAL mode.
2
When the key
is inserted, the
manual mode
will automati-
cally be se-
lected and the
MANUAL indi-
cator will light.
If a program
has been selected, press the PROGRAM SELECT
button repeatedly to select the manual mode again.
The LED track
represents 1/4
of a mile. As
you exercise,
the indicators
will light one
at a time until
the entire
track is lit.
The track will then disappear in a counterclockwise
direction and a new lap will begin.
Enter your weight and age if desired.
3
Although it is not necessary to enter your weight and
age to use the manual mode, the CALORIES display
will be more accurate if these numbers are entered.
To stop the walking belt momentarily, press the
STOP button once. All displays will pause and the
INCLINE/TIME display will begin to flash. To restart
the walking belt, press the START button as de-
scribed above. To stop the walking belt and reset all
displays, hold down the STOP button for two sec-
onds. The console will then be in the same state as
if the key had just been inserted.
To enter your weight,
press either of the SET
WEIGHT buttons. The
current weight setting
will appear in the
PULSE/CALORIES
display. Press the SET
WEIGHT buttons again to enter your weight. Each
time one of the buttons is pressed, the weight set-
ting will change by 1 pound. If one of the buttons is
held down, the weight setting will change in incre-
ments of 5 pounds.
Adjust the incline and speed of the treadmill.
6
While the walking belt is moving, the incline of the
treadmill can be adjusted with the INCLINE
buttons. Each time one of the buttons is pressed,
the incline will change by 0.5%. The buttons can
be held down to change the incline quickly. The
incline range is 0% to 12%. Note: After the buttons
are pressed, it may take a moment for the treadmill to
reach the selected incline setting.
To enter your age,
press either of the SET
AGE buttons. The
current age setting will
To adjust the speed of the walking belt, press the
SPEED buttons. Each time one of the buttons is
pressed, the speed will change by 0.1 mph. The but-
tons can be held down to change the speed in incre-
ments of 0.5 mph. The speed range of the walking
belt is 0.5 mph to 12.0 mph.
appear in the INCLINE/
TIME display. To enter
your age, press the
SET AGE buttons again. Each time one of the but-
tons is pressed, the age setting will change by 1
year. If one of the buttons is held down, the age set-
ting will change in increments of 5 years. Note:
Once you have entered your weight and age, the
numbers will be saved in the consoleÕs memory,
even if the power cord is unplugged.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the four displays.
DISTANCE/LAP dis-
playÑThis display
shows both the dis-
tance you have walked
7
PULSE/CALORIES dis-
playÑThis display
shows both your heart
rate (if the heart rate
and the number of laps
you have completed
monitor is worn) and the
approximate number of
calories you have
burned. The display will alternate between one num-
ber and the other every seven seconds.
(one lap equals 1/4
mile). The display will alternate between one number
and the other every seven seconds.
Note: If the speed is displayed in miles per hour, the
distance will be displayed in miles; if the speed is
displayed in kilometers per hour, the distance will be
displayed in kilometers.
Note: The heart rate monitor will sample your heart
rate every few seconds; it may take up to ten sec-
onds before an accurate heart rate is shown. If your
heart rate is not shown, see HEART RATE
When you are finished exercising, stop the
walking belt and remove the key.
8
MONITOR TROUBLE-SHOOTING on page 6.
INCLINE/TIME
displayÑThis display
shows both the incline of
the treadmill and the
elapsed time. (If a preset
program or a custom
program is selected, the
Step onto the foot rails, press the STOP button, and
remove the key from the console. Store the key in a
secure place. In addition, press the on/off switch to
the ÒoffÓ position. (See the drawing near the bottom
of page 9.)
display will show the time remaining in the program.)
The display will alternate between one number and
the other every seven seconds.
Note: Each time the INCLINE buttons are pressed,
the display will show the incline setting.
SPEED/PACE
displayÑThis display
shows both the speed of
the walking belt and
your current pace
(minutes per mile). The
display will alternate be-
tween one number and the other every seven
seconds.
Note: Each time the SPEED buttons are pressed,
the display will show the speed setting.
Note: The speed can be
displayed in either miles
per hour (mph) or kilo-
meters per hour (kph).
To check the unit of
measurement, first hold
down the STOP button
while inserting the key
into the console. The SPEED/PACE display will
show an ÒEÓ for ÒEnglishÓ (miles) or an ÒMÓ for
ÒMetricÓ (kilometers). Press the SPEED Ò+Ó button to
change the unit of measurement. Remove and then
reinsert the key.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Put on the heart rate monitor if desired.
HOW TO USE THE INCLINE PROGRAMS AND THE
SPEED PROGRAMS
4
5
For the PULSE/CALORIES display to show your
heart rate, the heart rate monitor must be worn. To
put on the heart rate monitor, see HOW TO USE
THE HEART RATE MONITOR on page 6.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 9.
Press the START button.
Select one of the incline or speed programs.
Press the START button to start the program. After
a moment, the walking belt will begin to move. Hold
the handrails and begin walking.
2
When the key
is inserted, the
manual mode
will automati-
cally be se-
lected and the
MANUAL indi-
cator will light.
To select one
of the incline or speed programs, press the PRO-
GRAM SELECT button repeatedly until the desired
INCLINE or SPEED indicator lights. Note: The first
incline program and the first speed program are
twenty-minute programs. All other preset programs
are thirty-minute programs.
If an incline program is selected: When the
START button is pressed, the walking belt will begin
to move at 1.0 mph and the incline will adjust to the
incline setting shown in the first column of the LED
matrix. After one minute (or 90 seconds if a thirty-
minute program is selected), the second column of
the LED matrix will begin to flash and the incline will
adjust to the incline setting shown in the second col-
umn. After another minute (or 90 seconds), the third
column will begin to flash and the incline will adjust
to the setting shown in the third column. The pro-
gram will continue in this way until the twentieth col-
umn is flashing and no time remains in the TIME dis-
play. The walking belt will then slow to a stop.
When an in-
cline or speed
The speed of the walking belt can be adjusted during
the incline program with the SPEED buttons. To stop
the program momentarily, press the STOP button
once. All displays will pause and the INCLINE/TIME
display will begin to flash. To restart the program,
press the START button. To end the program be-
fore it is completed, hold down the STOP button for
two seconds. The console will then be in the same
state as if the key had just been inserted.
program is se-
lected, the
LED matrix will
show all of the
incline or
speed settings
of the program.
Each incline program has twenty incline settings,
and each speed program has twenty speed set-
tings. One setting is shown in each vertical column
of the LED matrix. The first column will be flashing.
Note: Every few seconds, the words ÒPRESS
STARTÓ will scroll across the LED matrix.
While the incline program is in progress, the diffi-
culty level of the program can be adjusted, if de-
sired, with the INCLINE buttons. Press the INCLINE
Ò+Ó button once. The letters ÒMAXÓ will appear in the
LED matrix, and the INCLINE/TIME display will
show the maximum incline that the treadmill will
reach during the program. This information will be
displayed for three seconds. Press the INCLINE Ò+Ó
button again. Each time the button is pressed, the
maximum incline setting and all other settings of the
program will increase slightly. The INCLINE ÒÐÓ but-
ton can be used in the same way to decrease the
difficulty level of the program. Note: The profile
shown in the LED matrix will not change; the profile
shows relative incline settings.
Enter your weight and age if desired.
3
Although it is not necessary to enter your weight
and age to use an incline program or a speed pro-
gram, the CALORIES display will be more accurate
if these numbers are entered.
To enter you weight and age, refer to step 3 on
page 10. If you have already entered your weight
and age, or if you do not want to enter this informa-
tion, go to step 4.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If a speed program is selected: When the START
button is pressed, the walking belt will begin to move
at 1.0 mph, the speed setting shown in the first col-
umn of the LED matrix. After one minute (or 90 sec-
onds if a thirty-minute program is selected), the sec-
ond column of the LED matrix will begin to flash and
the speed will adjust to the speed setting shown in
the second column. After another minute (or 90 sec-
onds), the third column will begin to flash and the
speed will adjust to the setting shown in the third col-
umn. The program will continue in this way until the
twentieth column is flashing and no time remains in
the TIME display. The walking belt will then slow to a
stop.
HOW TO USE THE PULSE DRIVEN PROGRAMS
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 9.
Select one of the pulse driven programs.
2
When the key
is inserted, the
manual mode
will automati-
cally be se-
lected and the
MANUAL indi-
cator will light.
To select one
of the pulse driven
programs, press the PROGRAM SELECT button re-
peatedly until the desired PULSE DRIVEN indicator
lights. Note: Both pulse driven programs are thirty-
minute programs.
The incline of the treadmill can be adjusted during
the speed program with the INCLINE buttons. To
stop the program momentarily, press the STOP but-
ton once. All displays will pause and the INCLINE/
TIME display will begin to flash. To restart the pro-
gram, press the START button. To end the program
before it is completed, hold down the STOP button
for two seconds. The console will then be in the
same state as if the key had just been inserted.
The pulse
driven
programs
automatically
control the
speed and
incline of the
treadmill to
keep your
heart rate near predetermined settings during your
workout. When one of the pulse driven programs is
selected, the LED matrix will show all of the heart
rate settings of the program. Each program has
twenty heart rate settings. One setting is shown in
each vertical column of the LED matrix. The first
column will be flashing. Note: Every few seconds,
the words ÒENTER AGEÓ will scroll across the LED
matrix.
While the speed program is in progress, the difficulty
level of the program can be adjusted, if desired, with
the SPEED buttons. Press the SPEED Ò+Ó button
once. The letters ÒMAXÓ will appear in the LED ma-
trix, and the SPEED/PACE display will show the
maximum speed that the treadmill will reach during
the program. This information will be displayed for
three seconds. Press the SPEED Ò+Ó button again.
Each time the button is pressed, the maximum
speed setting and all other settings of the program
will increase slightly. The SPEED ÒÐÓ button can be
used in the same way to decrease the difficulty level
of the program. Note: The profile shown in the LED
matrix will not change; the profile shows relative
speed settings.
Follow your progress with the LED displays.
Refer to step 7 on page 11.
6
7
Enter your weight and age.
3
Remove the key from the console.
Although it is not necessary to enter your weight to
use a pulse driven program, you must enter your
age before one of these programs can be
started.
When the program has ended, remove the key from
the console. All displays and indicators on the con-
sole will darken.
To enter you weight and age, refer to step 3 on page
10. If you have already entered your weight and
age, press either of the SET AGE buttons to ver-
ify the age setting. The words ÒPRESS STARTÓ will
then scroll across the LED matrix every few seconds.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Put on the heart rate monitor.
4
5
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
The heart rate monitor must be worn when a pulse
driven program is used. See HOW TO USE THE
HEART RATE MONITOR on page 6. Note: A pulse
driven program can be started without a heart rate
reading; however, the speed and/or incline of the
treadmill will automatically decrease if your heart rate
is not detected during the program.
1
See HOW TO TURN ON THE POWER on page 9.
Select one of the custom programs.
2
To select one of the
custom programs,
Press the START button.
press the CUSTOM
PROGRAM 1 or
Press the START button to start the program. After a
moment, the walking belt will begin to move. Hold
the handrails and begin walking.
CUSTOM PROGRAM
2 button. The letters
ÒCP 1Ó or ÒCP 2Ó will
appear in the SPEED/
PACE display to show which program you have
selected.
While the first column of the LED matrix is flashing,
the walking belt will move at 1.5 mph. After 90 sec-
onds, the second column of the LED matrix will
begin to flash. As the program progresses, the
speed and/or incline of the treadmill will change at
any time to keep your heart rate near the heart rate
setting shown in the flashing column. When the
twentieth column begins to flash, the walking belt will
move at 1.5 mph until no time remains in the TIME
display. The walking belt will then slow to a stop and
the program will be completed.
Custom programs are workout programs that you
create. The programs are stored in the consoleÕs
memory, and can be changed as many times as
desired. Custom programs control both the speed
and the incline of the treadmill. When one of the
custom programs is selected, the LED matrix will
show the speed settings of the program (until you
have created a program, all speed settings will be
the same). The first column will be flashing. Note:
Every few seconds, the words ÒPRESS STARTÓ will
scroll across the LED matrix.
If your heart rate is not detected during the program,
the letters ÒPLSÓ will flash in the PULSE/CALORIES
display and the speed and/or incline of the treadmill
will automatically decrease. See HEART RATE
MONITOR TROUBLE-SHOOTING on page 6.
Enter your weight and age if desired.
3
4
While the program is in progress, minor adjustments
can be made to the speed or incline of the treadmill
with the SPEED or INCLINE buttons. However, if
you increase the speed, the incline will automatically
decrease; if you decrease the speed, the incline will
increase. If you increase the incline, the speed will
decrease; if you decrease the incline, the speed will
increase. The console will always attempt to keep
your heart rate near the heart rate setting shown in
the flashing column. Note: When the incline reaches
the lowest setting, the speed cannot be increased
any further. When the incline reaches the highest
setting, the speed cannot be decreased any further.
It is not necessary to enter your weight and age to
create a custom program; however, the CALORIES
display will be more accurate if these numbers are
entered.
To enter you weight and age, refer to step 3 on
page 10. If you have already entered your weight
and age, or if you do not want to enter this informa-
tion, go to step 4.
Press the START button.
Press the START button to start the program. After a
moment, the walking belt will begin to move. Hold
the handrails and begin walking.
Follow your progress with the LED displays.
Refer to step 7 on page 11.
6
7
Remove the key from the console.
When the program has ended, remove the key from
the console. All displays and indicators on the con-
sole will darken.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the RECORD button and program the de-
sired speed and incline settings.
5
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
When the RECORD button is pressed, the indicator
on the button will light. Speed and incline settings
can be programmed only when the indicator on
the button is lit.
1
See HOW TO TURN ON THE POWER on page 9.
Select one of the custom programs.
Refer to the
LED matrix.
Each custom
program is
divided into
one-minute
segments. One
speed setting
and one incline
setting can be programmed for each one-minute
segment. The speed setting of the first segment is
shown in the flashing column of the LED matrix.
(The incline settings are not shown in the LED ma-
trix.) To program the desired speed and incline set-
tings for the first segment, simply adjust the speed
and incline of the treadmill to the desired levels with
the SPEED and INCLINE buttons. Every few times
the SPEED Ò+Ó or ÒÐÓ button is pressed, an additional
LED will light or darken in the flashing column.
2
To select one of the
custom programs,
press the CUSTOM
PROGRAM 1 or
CUSTOM PROGRAM
2 button. The letters
ÒCP 1Ó or ÒCP 2Ó will
appear in the SPEED/
PACE display to show which program is selected.
When a custom program is selected, the LED matrix
will show the speed settings of the program. If the
program is more than twenty minutes long, only the
first nineteen settings will be shown. The first column
will be flashing. Note: Every few seconds, the words
ÒPRESS STARTÓ will scroll across the LED matrix.
Enter your weight and age if desired.
3
4
When the first one-minute segment of the program
is completed, the current speed setting and the cur-
rent incline setting will be stored in memory. All
columns in the LED matrix will then move one posi-
tion to the left, and the speed setting of the second
segment will be shown in the flashing column.
Program speed and incline settings for the second
segment as described above.
It is not necessary to enter your weight and age to use
a custom program; however, the CALORIES display
will be more accurate if these numbers are entered.
To enter you weight and age, refer to step 3 on
page 10. If you have already entered your weight
and age, or if you do not want to enter this informa-
tion, go to step 4.
Repeat this procedure until you have programmed
speed and incline settings for as many segments as
desired. Custom programs can have from one to
forty segments. When you are finished, hold down
the STOP button for two seconds. The speed and in-
cline settings you programmed and the number of
segments will then be stored in memory. To use the
program again, see HOW TO USE A CUSTOM PRO-
GRAM at the right.
Press the START button.
Press the START button to start the program. After a
moment, the walking belt will begin to move. Hold
the handrails and begin walking.
Refer to the
LED matrix.
Each custom
program is di-
Note: To pause the program temporarily while you
are programming speed and incline settings, press
the STOP button once. All displays will pause and the
TIME display will begin to flash. To restart the pro-
gram, press the START button.
vided into one-
minute seg-
ments. One
speed setting
and one in-
cline setting are programmed for each segment. The
speed setting of the first segment is shown in the
flashing column of the LED matrix. The speed set-
tings of the next six segments are shown in the six
columns to the right. (The incline settings are not
shown in the program display.)
Remove the key from the console.
6
When the program has ended, remove the key from
the console. All displays and indicators on the con-
sole will darken.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
When the first one-minute segment of the program
is completed, all columns of the LED matrix will
move one position to the left, the speed setting of
the second segment will be shown in the flashing
column, and the speed of the treadmill will change
accordingly. The incline will also change according
to the settings that you programmed previously.
HOW TO SELECT THE INFORMATION MODE
The console features an information mode that keeps
track of the total time and distance accumulated on the
treadmill.
To access the information mode, hold down the STOP
button while inserting the key into the console. The
INCLINE/TIME display will show the total number of
hours accumulated on the treadmill. The DISTANCE/
LAP display will show the number of miles accumulated
(if the total number of miles exceeds 999, the thousands
and ten thousands digits will be shown in the right half
of the SPEED/PACE display). The left half of the
SPEED/PACE display will show which unit of measure-
ment is currently selected: an ÒEÓ for ÒEnglishÓ (miles) or
an ÒMÓ for ÒMetricÓ (kilometers). To change the unit of
measurement, press the SPEED Ò+Ó button.
The program will continue in this way until the speed
setting of the last segment is shown in the flashing
column and no time remains in the TIME display.
The walking belt will then slow to a stop.
Note: If the program is too easy or too difficult, the
speed or incline setting of the current segment can be
adjusted with the SPEED or INCLINE buttons.
Adjustments will not be stored in memory. To repro-
gram the speed or incline setting of the current seg-
ment, press the RECORD button. The indicator on the
button will light. Speed and incline settings can be
programmed only when the indicator on the button
is lit. Adjust the speed or incline setting of the current
segment with the SPEED or INCLINE buttons. After
the segment is completed, press the RECORD button
again. The new setting will then be stored in memory.
To exit the information mode, remove the key from the
console.
HOW TO ADJUST THE CUSHION LEVEL OF THE
TREADMILL
The treadmill is specially designed to cushion the
impact as you walk or run. The cushion level is con-
trolled with the knob on the right side of the treadmill.
For a softer cushion level, turn the knob counterclock-
wise. For a firmer cushion level, turn the knob clock-
wise. Note: The faster you run on the treadmill, the
firmer the cushion level should be. If the cushion level is
too soft, the treadmill may bounce
To stop the program momentarily, press the STOP
button once. All displays will pause and the INCLINE/
TIME display will begin to flash. To restart the pro-
gram, press the START button. To end the program
before it is completed, hold down the STOP button
for two seconds. The console will then be in the
same state as if the key had just been inserted.
excessively.
Follow your progress with the LED displays.
Refer to step 7 on page 11.
5
6
Remove the key from the console.
When the program has ended, remove the key from
the console. All displays and indicators on the con-
sole will darken.
Cushion
Knob
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, unplug the power cord. Caution:
You must be able to safely lift 45 pounds (20 kg) in order
to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Hold the lock knob with your left hand
2
and pull it to the side. Raise the treadmill until the lock
knob is aligned with the catch. Slowly release the knob.
Make sure that the pin on the lock knob is inside of
the catch.
Lock
Knob
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the pin
on the lock knob is inside of the catch.
1. Hold the handrails and place one foot on the base as
shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not move the treadmill
over an uneven surface.
Base
3. Place one foot on the base and carefully lower the tread-
mill until it is resting on the base.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Hold the lock
knob with your left hand and pull it to the side. Pivot the treadmill down a few inches.
2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. To
decrease the possibility of injury, bend your legs and keep your back straight.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. If further assistance is
needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m.
Central Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppres-
sor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation
of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. (See step 3 on page 9.)
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
c
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Tripped
Reset
d
d. Check the on/off switch located at the front of the
treadmill near the power cord. The switch must be
in the ÒonÓ position.
ÒOnÓ
Position
OFF
ON
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. (See step 3 on page 9.)
d. Make sure that the on/off switch is in the ÒonÓ position. (See 1. d. above.)
e. If the treadmill still will not run, please call our toll-free HELPLINE.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps.
b. If the walking belt still slows when walked on, please call our toll-free HELPLINE.
PROBLEM: The walking belt is off-center when walked on
a. If the walking belt has shifted to the left, first remove
a
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counterclockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b
c. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts
clockwise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side of
the walking belt 3 to 4 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key and carefully walk on
the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
c
PROBLEM: The heart rate monitor does not function properly
a. If the heart rate monitor does not function properly, refer to HEART RATE MONITOR TROUBLE-
SHOOTING on page 6.
b. The CR 2032 battery may need to be replaced.
If the heart rate monitor still does not function properly, the battery
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the ÒopenÓ position. Remove
the cover.
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Rubber
Gasket
PROBLEM: An error code (E1, E20, E21, E22, E23, OR E24) appears on the console
a. If an error code appears, remove the key from the console, wait for a moment, and then reinsert
it. If the error code appears again, call our Customer Service Department. Do not use the tread-
mill until the problem is corrected.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
Burning Fat
WARNING:
Before beginning
To burn fat, you must exercise at a low intensity level
for a sustained period of time. During the first few
minutes of exercise, your body uses easily accessible
carbohydrate calories for energy. Only after the first few
minutes of exercise does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the intensity of your exercise until your heart rate is
near the low end of your training zone as you exercise.
this or any exercise program, consult your
physician. This is especially important for in-
dividuals over the age of 35 or individuals
with pre-existing health problems.
The following guidelines will help you to plan your ex-
ercise program. RememberÑthese are general guide-
lines. For more detailed information about exercise,
obtain a book or consult your physician.
WARNING:
The heart rate moni-
tor is not a medical device. Various factors, in-
cluding your movement, may affect the accu-
racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid in
determining heart rate trends in general.
EXERCISE INTENSITY
Whether your goal is to burn fat or strengthen your car-
diovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. For effective exercise, your heart rate
should be maintained at a level between 70% and 85%
of your maximum heart rate as you exercise. This is
known as your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the intensity of your exercise until your heart
rate is near the middle of your training zone.
You can find your training zone in the table below.
Training zones are listed according to age and physical
condition.
Training Zone (Beats/Min.)
WORKOUT GUIDELINES
Unconditioned
Conditioned
Age
Each workout should include the following three impor-
tant parts: (1) a warm-up, (2) training zone exercise,
and (3) a cool-down.
20
25
30
35
40
45
50
55
60
65
70
75
80
85
138-167
136-166
135-164
134-162
132-161
131-159
129-156
127-155
126-153
125-151
123-150
122-147
120-146
118-144
133-162
132-160
130-158
129-156
127-155
125-153
124-150
122-149
121-147
119-145
118-144
117-142
115-140
114-139
Warm-up
Warming up prepares the body for exercise by increas-
ing circulation, delivering more oxygen to the muscles,
and raising the body temperature. Begin each workout
with 5 to 10 minutes of stretching and light exercise to
warm up (see SUGGESTED STRETCHES on page 21).
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 60 minutes. (During the first few weeks of your exer-
cise program, do not keep your heart rate in your train-
ing zone for longer than 20 minutes.) Breathe regularly
and deeply as you exerciseÑnever hold your breath.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Cool-down
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired.
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the
right. Move slowly as you stretchÑnever bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for each leg. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. 831.297572
R1098A
Note: To identify the parts listed below, refer to the EXPLODED DRAWING attached at the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
34
5
4
2
2
2
8
2
1
1
1
2
2
1
1
4
1
4
1
5
2
2
3
3
3
2
2
1
1
1
1
1
1
1
9
2
3
4
1
2
1
2
2
2
1
2
2
1
1
1
1
Frame
Screw
Isolator Nut
Spring Bolt
Cushion Spring
Isolator
Cushion Adj. Rack
Rack Screw
Cushion Adj. Gear
Motor/Pulley/Flywheel/Fan
Latch Housing
Left Foot Rail
Rear Platform Screw
Roller Guard
Walking Platform
Rear Roller
Incline Pivot Bolt/Incline Motor Nut
Front Roller/Pulley
Motor Bolt
Console Base
Bracket Screw
Hood Anchor
Hood Anchor Bracket
Motor Bracket Bolt
Motor Bracket Washer
Long Hood Bracket
Belt Guide
Motor Tension Bolt
Outlet Bracket
Circuit Breaker
Power Cord
Power Cord Grommet
On/Off Switch
Incline Leg
Front Roller Adj. Bolt
Roller Adj. Washer
Incline Leg Spacer
Incline Leg Pivot Nut
Motor Nut
Motor Pivot Bolt
Roll Pin
Key/Clip
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
2
2
1
8
5
1
1
1
5
1
1
1
2
1
2
1
1
1
19
1
4
8
1
1
1
5
1
1
4
1
1
1
2
1
1
2
2
2
4
1
9
1
1
2
2
2
1
1
1
1
1
1
Sensor Wire
Shock
Walking Belt
Belly Pan Spacer
Motor Pivot Nut
Cushion Shaft
Belly Pan
Right Foot Rail
8Ó Cable Tie
Motor Bracket
Tie Holder
Releasable tie
Short Rear Roller Adj. Bolt
Rear Roller Endcap
Endcap Pad
Pulse Monitor
Monitor Strap
Console
Upright Cap Screw
Motor
Upright Cap
Console Screw
Console Plate
Pulley/Flywheel/Fan
Hood
9
10*
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Hood Screw
Cushion Knob
Power Board
Plastic Stand-Off
Set Screw
Controller
Upright Wire Harness
Isolator Bolt
Electronics Plate
Upright Cover (right inside)
Upright Cover
Platform Screw (front)
Wheel Bolt
Front Wheel
8Ó Ground Wire
Wheel Nut
Adhesive Clip
Allen Wrench
Upright Cap
Handrail Foam
Handrail Endcap
Lock Knob
Lock Knob Sleeve
Lock Knob Spring
Lock Pin Collar
Lock Pin
Flange Nut
Motor Tension Washer
Small Nut
4Ó Wire Tie
Small Bolt
Sensor
Speed Sensor Bracket
Speed Disk
Motor Belt
Warning Decal
Pin Clip
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
105
106
107
108
109
110
111
112
113
114
115
116
2
1
2
2
1
2
1
1
1
1
1
1
Platform Washer
Stop Bracket
Incline Decal
Small Star Washer
Incline Disk
Console Bracket Screw
Incline Motor
I-Bolt
117
118
119
#
#
#
#
#
#
#
1
1
2
1
1
1
1
1
1
1
Console Wire Harness
Battery Cover
Spring Spacer
14Ó White Wire, 2 Female
14Ó White Wire, Male/Female
14Ó Blue Wire, 2 Female
8Ó Blue Wire, 2 Female
9Ó Black Wire, Male/Female
8Ó Red Wire, Male/Female
UserÕs Manual
Receiver
Belly Pan Hinge
Upright/Base
Upright Cover (left outside)
* Includes all parts shown in the box
# These parts are not illustrated
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
The model number and serial number of your IMAGE¨ 10.6Q tread-
mill are listed on a decal attached to the frame. See the front cover
of this manual to find the location of the decal.
Model No. 831.297572
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
QUESTIONS?
If you find that:
¥ you need help assembling or
operating the IMAGE¨ 10.6Q
treadmill
When requesting help or service, or ordering parts, please be pre-
pared to provide the following information:
¥ a part is missing
¥ The NAME OF THE PRODUCT (IMAGE¨ 10.6Q treadmill)
¥ The MODEL NUMBER OF THE PRODUCT (831.297572)
¥ or you need to schedule repair
service
call our toll-free HELPLINE
¥ The PART NUMBER AND DESCRIPTION OF THE PART (see
the PART LIST on page 22 and the EXPLODED DRAWING at-
tached in the center of this manual)
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need
to be replaced, call the following
toll-free number
1-800-FON-PART
(1-800-366-7278)
FULL ONE YEAR WARRANTY
For one year from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS TREADMILL EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the TREADMILL EXERCISER, free of charge.
This warranty does not apply when the TREADMILL EXERCISER is used commercially or for rental pur-
poses.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 148934 H03534-C R1098A
Printed in USA © 1998 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|