Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety ................................................................. GB2
Copyright & Glossary ......................................... GB3
Reference ........................................................... GB4
STB Connections ................................................ GB5 ~ GB8
Remote Control Unit ........................................... GB9 ~ GB10
Guide of Functions ............................................. GB11 ~ GB13
Guide of Main Menu ........................................... GB14 ~ GB33
Troubleshooting Guide ....................................... GB34
Menu Map ........................................................... GB35 ~ GB36
Specification ....................................................... GB37 ~ GB38
GB1
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright & Glossary
CAUTION
To watch Pay Per View programmes, be sure to inform your STB dealer of the STB’s and Smart card’s serial
numbers. So that they can pair your STB with your Smart card. Otherwise, you cannot watch the programmes
because they are scrambled.
NOTE
When the changed Network Information is sent, Nagravision realizes that the appropriate satellite/cable service
information has been changed. And it will re-organize the service information based on the sent Network
Information. The message “Network Information updated...” appears on the screen. It is automatically done
when changing NIT. The manufacturer can’t change it because it is provided by Nagravision. When the user
watches it, the message may suddenly appear during AV playback and simultaneously updating will proceed.
(This happens about once a year.) Since this is not an error in operating, do not turn off the power.
Copyright
• Nagravision is a registered trademark of Kudelski S.A.
• VIACCESSTM is a trademark of France Telecom.
• CryptoWorks(TM) is a trademark of Philips Electronics N.V.
• Irdeto is a trademark of Mindport BV.
• Conax is a trademark of Telenor Conax AS.
• “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Warning
HUMAX cannot be held responsible for any kind of problems caused by the use of unofficial
software. The use of software versions other than HUMAX official software will void the
manufacturer’s warranty. It is advised that only the formal software released from HUMAX
should be used in all HUMAX product range.
Glossary
• Antenna
A device that collects and radiates electromagnetic waves.
Includes a satellite dish and abroadband antenna.
• Forward Error Correction(FEC)
A system of error control for data transmission.
• Frequency
The number of cycles or events per one second, which is expressed in the unit of Hertz(Hz).
• Intermediate Frequency (IF)
A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception.
• Packet Identifier (PID)
A set of numbers that idenitifies transport stream packets containing data from a single data stream.
• Service
A channel to which a decoder or TV is tuned.
GB3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
1. Loop Through
If you have another analogue or digital STB and you wish to use the same RF Signal then
you can connect it via the loop through. Connect one end of a RF cable to the TV/VCR on
the STB and connect the other end to the RF(ANT) on your second STB.
2. Software Upgrade
HUMAX digital set-top box is a highly sophisticated product - incorporating one of the best
software applications.
Whenever a problem is found with this software or, in fact, extra functions or enhanced
applications are added, the software in the equipment has to be upgraded.
In order to maintain proper performance of the product, it is essential to have the most
up to date software. The latest news and release of software versions may be found at
It is recommended that users register to HCSA (HUMAX Customer Service Area) and
periodically check for the availability of software upgrade.
There are three methods to upgrade the software :
(a) set-top box to set-top box download (copies the software of the main unit into slave unit);
(b) pc to set-top box download (downloads the software directly from pc to the model
requiring upgrade);
(c) OTA over-the-air (downloads the software where the manufacturer reserves the right to
decide when and where to release over the air).
Over The Air (OTA) is simply another alternative for downloading software versions.
However, the manufacturer reserves the right to decide when and where this software
upgrade can take place by "beaming" latest software versions over the air.
SUSS (TM) is an official trademark and logo for HUMAX loader software to perform OTA.
The software upgrade will only occur under the following circumstances:
1) the equipment should have appropriate loader software;
2) the manufacturer decides to release software downloading;
3) the equipment must be "tuned" properly to the OTA channel that the manufacturer uses.
GB4
Download from Www.Somanuals.com. All Manuals Search And Download.
STB Connections
Front Panel
F1-4000T Free-To-Air
NA-4710T 1 Smart card
STANDBY
1
2
Press to switch between Operation and Standby modes.
TV/RADIO
Press to switch between TV and Radio modes.
- p +
3
3
5
Use to change services down/up.
- v +
Use to change volume down/up.
STANDBY LED(RED)
Indicates that the STB is under standby.
6 TV LED(AMBER)
The LED lights on in TV mode.
7 RADIO LED(GREEN)
The LED lights on in RADIO mode.
8 DISPLAY
Shows service number, error messages, RCU commands and time
in Standby mode.
GB5
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
1
2
3
4
TV SCART
For the audio/video input of the TV.
VCR SCART
For the VCR.
AUDIO/VIDEO OUTPUT
Audio/video signal from your STB to VCR or TV.
ANTENNA
Use to connect a general Aerial Antenna and CABLE jacks to
a ANTENNA input jack on the STB.
TV/VCR
4
4
Use to connect a RF signal from your STB to RF(ANT) input jack
on your TV or VCR .
RS-232C
Use it when connecting to your PC.
GB6
Download from Www.Somanuals.com. All Manuals Search And Download.
STB Connections
Example 1
In this example a TV set is connected
to the digital receiver. If possible the TV
should be connected with the digital
receiver through a Scart cable.
If the TV doesn’t have a Scart
connection or if you want to connect a
second TV to the digital receiver, the
UHF output of the modulator may be
used.
Example 2
In example 2 a VCR and a hifi stereo
components system are connected to the
digital receiver in addition to the TV.
The VCR should be connected through
a Scart cable. In this example the hifi
stereo components system is connected
with the digital receiver through the
analogue Cinch connections.
GB7
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 3
In this example the terrestrial digital
receiver is operated together with the
satellite receiver. Both of the receivers
should be connected through a Scart
cable. Plug the Scart cable of the
satellite receiver into the VCR Scart
of the DVB-T receiver. As soon as the
satellite receiver is turned on, its audio
and video signals will be looped through
the terrestrial digital receiver.
Example 4
This pattern corresponds to example 3
(see above). A VCR was switched
additionally to the configuration.
Connect the VCR with the satellite
receiver through a Scart cable. Plug the
Scart cable of the VCR into the VCR or
video Scart (if available) of the satellite
receiver.
GB8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Unit
GB9
Download from Www.Somanuals.com. All Manuals Search And Download.
NUMERIC BUTTONS
Press to select a service, enter your PIN Code or
numeric on the menu.
TV/DTV
Press to select the TV/DTV mode.
10
1
2
TV/RADIO
Press to select the TV/RADIO mode.
11
12
13
INFORMATION (RED)
Press to display the programme information box
on the screen. And this button functions same as
the RED button on the menus.
MUTE
Press to temporarily cut off the sound.
SOUNDTRACK (GREEN)
Press to display the soundtrack list for the current
service. And this button functions same as the
GREEN button on the menus.
3
4
MENU
Press to display the Main Menu on the screen
or return to the screen from a sub menu screen.
14 CURSOR
SUBTITLE (YELLOW)
Press to display the subtitle language list for the
current service. And this button functions same as
the YELLOW button on the menus.
Press to move the highlight bar for selecting
options on the menus.
And this button is used to change services
(up/down) and increase or decrease the audio
volume.
UHF (BLUE)
Press to set the UHF menu.
This button functions same as the BLUE button on
the menus.
5
6
15 OK
Press to display the service list.
This button is used to select the item on the menus.
TIME (WHITE)
16 P+/P-
Press to display the current time on the screen.
Press to reserve services on the Informaion box or
EPG. And this button functions same as the WHITE
button on the menus.
Programme up/down buttons.
Press to tune to the next or previous service.
Press to move up or down pages on the menus.
HELP
17
EXIT
7
8
Press to display the help box on the screen.
Press to return to the previous menu and screen.
18 EPG
V+/V-
Volume up/down buttons.
Electronic Programme Guide button displays
the TV/Radio programme guide.
Press to increase or decrease the volume.
RCL (Recall)
Press to select the service that was previously
viewed.
19
STANDBY
Press to switch between Operation and Standby
9
modes.
•
Please note : The design of Remote Control Unit may be changed without notice in advance.
GB10
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Functions
Information Box (I-Plate)
The details of service part and event part are automatically
displayed on the I-Plate when pressing the i button(
changing services.
) or
I-Plate is divided into service part and event part.
SERVICE-PART (Left side of the box)
SERVICE PART consists of the following items:
• I-Plate icon, Current time and Dolby Digital symbol
• Service name, Service number, icons
• Subtitle, Teletext, Scrambling service symbol
(These are automatically displayed when the broadcasting
station provides appropriate information.)
• Signal quality bar
EVENT-PART (Right side of the box)
EVENT PART consists of the following items:
• Event name, Event duration time
• Description text of event, State of reserved event
Event Part shows the current and next event information.
button : Use to move from the current event information to
the next event information.
button : Use to move from the next event information to
the current event information.
When the HELP(
)button is pressed under I-Plate display and
there are no detailed event informations in the I-Plate,
the Help window will appear on the screen.
The Help window shows the current Network information, including:
Satellite Name, Frequency, Polarisation, Symbol Rate, FEC...
The detailed information for the event can be displayed by pressing
the HELP(
You can reserve the programme in the event data display mode by
using the WHITE( )button.
)button in the I-Plate with event data displaying mode.
You can reset timer programme Once, Daily or Weekly mode.
When you release the timer programme mode, then you will be
asked to confirm the action.
GB11
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Services
To change services, do in the following sequence;
1. Press the NUMERIC buttons(0~9) on the remote control unit.
2. Press the
buttons or
buttons.
Or press the RECALL(
), Service-list(
), EPG(
)mode
button.
To switch between TV and Radio services, press the TV/Radio
) button.
(
To select the previous viewed Service, press the RECALL(
)
button.
Volume Control
To adjust the volume level, use the
To temporarily stop the volume, press the MUTE(
To cancel mute, press the MUTE( )button again or press the
buttons or
buttons.
)button.
buttons or
buttons.
Soundtrack
When you want to change the audio language of current service,
press the GREEN( )button firstly.
The on-screen menu is displayed on the top to left side of the
screen.
To change the audio language:
1.
2.
3.
buttons : Use to select the audio on the left, right or both.
buttons : Use to select the audio language you want.
button : When this button is pressed, the Soundtrack
OSD will disappear keeping the selected
,
Soundtrack language constant.
When the current service is switched, the audio language returns to
the audio language that was selected in previous service. lf the
returned audio language is invalid, the audio language that you
selected from the audio language menu has the priority of playback.
Soundtracks broadcast in Dolby Digital are indicated by
Dolby Digital symbols either side of the respective language
selection in the menu. By selecting such a soundtrack the Dolby
Digital audio will be output by the optical S/PDIF on the STB.
This can be decoded by an external Dolby Digital television or
amplifier, for example.
GB12
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Functions
Subtitle
When the current broadcasting programme provides subtitle, press
the SUBTITLE( )button to see the current subtitle language list.
To change the subtitle language:
1. Use the
2. Press the
buttons to select a Subtitle language you want.
button and the selected language is highlighted
and then the Subtitle Language you want is displayed on the
screen.
Press the
button to cancel the Subtitle mode.
Teletext
Use your TV Remote Control Unit to control the Teletext service.
The teletext button doesn’t exist on the STB Remote Control Unit.
When the service supports Teletext, the Teletext icon( ) is
displayed on the I-plate.
GB13
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
1. Select Service
The select service displays the required service list which can be
viewed in Simple or Advanced mode.
2. TV Guide
Your STB has an Electronic Programme Guide (EPG) to help you
navigate through all the possible viewing options.
The TV Guide supplies information such as programme listings and
start and end times for all available services.
In addition, detailed information about the programme listings and
start and end times for all available services.
In addition, detailed information about the programme is often
available in the EPG (the availability and amount of these
programme details will vary, depending on the particular
broadcaster).
3. Parental Control
Access to services and programmes is controlled by a PIN Code
(i.e., a 4-digit secret code that is defined by the user).
The very first time you attempt to lock all services (or lock
programmes by ratings), the on-screen menu will instruct you to
assign a PIN Code (Later on, if necessary, you can change it).
4. Installation
The Installation mode allows you to have the information of setting
services and newly set services (language, time, organise,
search,..).
Furthermore, you can recognize the states of hardware and
software versions and signals from your STB.
5. Utility
This menu provides Calendar and Biorhythm.
GB14
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
1. Select Service
To select the desired in the service list, you should firstly
display the service list using
select a service and press
button. Use
button. Also use
buttons to
buttons to
select a service directly in the service list.
The contents of service list are as follows:
Simple Service List
1. Use the
buttons to select “Select Service” from the
button.
Main Menu and press the
2. Use the
press the
buttons to select “Simple” from the Main Menu and
button.
3. Then the simple service list(max. 10 services) will appear on the
screen.
Advanced Service List
The advanced service list shows thirty services. This list is similar
to the Simple service list except that it shows thirty services and is
apart from the Network and Genre list that displays twenty servies.
Use the following colour buttons to list various service lists:
The colour button corresponds the following Service List.
• RED
• GREEN (
• YELLOW(
(
)button - service list All
)button - Favourite
)button - Network
• BLUE
• WHITE
(
(
)button - Genre
)button - service list by Alphabetical order
Service Configuration
To change the attributes of a service
1. Use the
buttons to move a service you want to change
in the Service List.
2. Press the MENU(
)button.
3. Use the buttons to move to an item(such as genre, favourite,
lock, skip, delete) you want on the Service Configuration screen.
4. Use the
buttons to select. Press the
button to complete.
Service All
1. To display the Service All, press the
Use RED( )button to select the service All list.
2. Select the desired service by using the buttons.
3. Press the button to view the selected service.
button
The service list provides you the Simple mode and Advanced
mode. The right side scroll-bar of the screen displays the
location of the selected service in relation to All services.
Press the RED(
)button to toggle between Simple mode and
Advanced mode.
GB15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Favourite
1. Press the GREEN(
)button on the remote control unit to
select the Favourite service list.
Note : The groups are labeled in four different alphabet characters
(A,B,C,D).
2. Use the
buttons to select a favourite group that you want.
3. Press the GREEN(
)button to toggle group and service list.
Service Network
1. Press the YELLOW(
)button on the remote control unit to
select the Network service list.
2. Use the buttons to select a service
3. Press the YELLOW( )button to toggle provider and service list.
Note : 1. The provider name is displayed on the left window and
the provider’s services are displayed on the right window.
2. The scroll bar on left of the screen shows the location of
the cursor in the Network. The scroll bar on right of the
screen shows the location of the service from the
selected Network.
Service Genre
1. Press the BLUE(
select the Genre service list.
2. Use the buttons to select a service.
3. Press the BLUE( )button to toggle Genre and service list.
)button on the remote control unit to
Note : The scroll bar on left of the screen shows the location of
the cursor in the selected Genre. The scroll bar on right
of the screen shows the location of the service.
Service Alphabet Order
1. Press the WHITE(
select the Alphabet service list.
2. Use the buttons to select a service.
3. Press the WHITE( )button to toggle Alphabet and service list.
)button on the remote control unit to
Note : The scroll bar on left of the screen shows the location of the
cursor in the Alphabet. The scroll bar on right side of the
screen shows the location of the selected Alphabet service.
GB16
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
2. TV Guide
You can watch a programme being shown and reserve it in the
TV Guide mode.
To enter the TV Guide mode
Press the EPG(
)button on the remote control unit or select
the TV Guide on the Main Menu.
To select the TV/Radio Guide
Press the TV/Radio(
)button on the remote control unit and
TV Guide will be switched to the Radio Guide.
TV Guide mode includes four different modes.
To select each mode, use the following buttons:
• RED
(
)button : Use to display the current and next
programme list.
• GREEN (
• YELLOW(
)button : Use to display the programme list for
one-week.
)button : Use to display the reserved programme
list.
• BLUE
(
)button : Use to display the simple TV Guide list.
(Quick mode)
Now/Next mode
Show the informations of the programmes that are played now or
will be played next time.
This mode consists of the service name, event name, event
duration time, current time and on-screen-display window.
To watch a programme you want through the display window :
• Use the
The selected service will appear on the right display window.
• Use the buttons to select a programme you want.
And then press the button on the remote control unit.
buttons to select a programme you want.
The selected service will appear on the right display window.
The selected OSD will be highlighted every time the cursor
moves.
To reserve a programme you want :
• Select a programme you want by using the
buttons or
)button.
buttons. And then press the WHITE(
Press the
buttons to watch the programme of previous page
or the programme of next page. Press the YELLOW(
)button
to watch the Reserved programme list.
GB17
Download from Www.Somanuals.com. All Manuals Search And Download.
Weekly mode
Shows the information of programmes that will be played for a
week. Select a day you want using the
buttons.
To watch and reserve a programme you want, do the same steps
with the Now/Next mode.
Reserved mode
Shows the programme lists that you have already reserved on the
TV Guide or Information box.
Maximum eight programmes can be reserved.
This programme list includes service name, date, duration time,
reservation mode and event name.
To cancel the Reserved service, select a programme you want
to cancel using the
button.
buttons and then press the WHITE(
)
Quick mode
Shows a simple TV Guide like an Information box.
This mode shows in the A/V playback mode.
• Red vertical line : Indicates the current time.
• Black/white bar : Shows the proceeding state of programme.
• Time range of bar : This consists of three blocks by 30 minutes
per block.
GB18
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
3. Parental Control
You can set a parental guidance rating to each programme
in this mode.
1. When the
button is pressed after selecting the highlighted
parental control on the initial menu screen, a display window
for entering the PIN code will appear on the centre of screen.
0 0 0 0
** The default PIN code is
.
2. Enter the PIN code on the display window.
(If any problem occurs when entering a PIN code, you cannot
switch to the next mode.)
3. Set the parental guidance rating of highlighted censorship
classification.
The parental level is given as age-based numbers :
no block, 6, 10, 14, 18 and total block. Enter the PIN code
to unlock or lock programmes.
4. To change your PIN code:
• Select the highlighted Old PIN code using the
and then enter your Old PIN code.
buttons
• Enter a New PIN code in the highlighted New PIN code
using the buttons.
• To verify the New PIN code, re-enter a New PIN code in the
highlighted Verify Changed PIN code.
5. When the entered PIN code is correct, then all settings are
completed.
(If the PIN code is wrong, the message “PIN code mismatch”
will be displayed on the display window. When the
button
is pressed at this time, the Old PIN code is valid and the
cursor is located in the first position of this menu.)
GB19
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Installation
This mode allows you to customise, add a new service and
displays the state of the STB. Enter the submenus after selecting
the Installation mode in the Main Menu.
4-1. System Setting
The System Setting mode supports the STB internal settings
according to the connection of the receiver and external units.
This mode includes Language Setting, Time Setting,
A/V Output Setting, UHF Tuning and Other Settings.
Language Setting
Select the language for menu, audio or subtitle.
1. Select the highlighted language setting using the
in the system setting mode and then press the
buttons
button.
2. Select the highlighted Menu(or Audio, Subtitle) Language and
press the
3. Use the
press the
buttons and the language list will be displayed.
buttons to move to a language you want and then
button to finish setting.
Menu Language
Select a language for the menu or banner OSD in this mode.
You can choose the language from a selection of English and
German.
When a broadcasting information (event) is transmitted,
the selected Menu Language will be applied.
Audio Language
Select the default language for audio when changing services.
If you change the current service, your STB will initially select
the previously memorised Audio Language. If the Audio Language
of current service is not provided, at this time, you should reselect
a language on the Audio Language menu.
Languages provided:
Czech, Danish, Dutch, English, Finnish, French, German, Greek,
Hungarian, Italian, Norwegian, Portuguese, Rumanian, Russian,
Spanish, Swedish, Turkish and more.
If no language is provided, then the default language of current
service will be automatically selected.
Subtitle Language
Select the default language for subtitle when changing services.
Language provided: Danish, English, Finnish, French, German,
Greek, Hungarian, Italian, Norwegian, Portuguese, Spanish,
Swedish and more.
GB20
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
Time Setting
You can set the Current Time and Wakeup Time in this mode.
Furthermore, the Service Number in the Wakeup mode and Sleep
Time (standby mode) can be set. When a VCR is connected,
recording can be automatically done according to Wakeup/Sleep
Time Setting.
Current Time
To set the Current Time, enter the Offset value using the
standardised information of current service area.
The time setting will be used as the standardised time for the
I-Plate, TV Guide, Wakeup and Sleep Timer.
Time Offset
Current Time is based on TDT (Time and Data Table) at the stream
of the current service.
Timer
You can select nine kinds of Timer like 1,2.......8 and Disabled.
If you select “Disabled”, then the other timers will not work. Press
the
button at timer option to display the Timer table. The Timer
determines the on/off time and can also be used for VCR recording.
Timer Mode
Wakeup/Sleep timer determines the Timer Mode.
• Once : The timer programming is applied only once.
• Daily : The timer recording is applied everyday repeatedly.
• Weekly : The timer recording is applied weekly.
(Set one day in a week).
Use the
buttons to select the type of timer programming.
Wakeup Time
Select the time when STB is turned on.
Use the NUMERIC buttons(0~9) on the remote control unit to enter
your Wakeup Time.
Wakeup Service No.
Use the
buttons to set the service number provided for the set
Wakeup Time.
Use the TV/Radio(
TV/Radio service.
)button on the remote control unit to toggle
Service Name
The Service Name that has been determined by the
Wakeup Service No. will be shown.
Sleep Time
Depending on Time Setting, select the time when STB is turned off.
GB21
Download from Www.Somanuals.com. All Manuals Search And Download.
A/V Output Setting
Video Output (CVBS/S-Video/RGB)
Set the video mode for the TV SCART output.
Audio Output
Set the audio mode which is output from the TV SCART and
RCA/Cinch Jack. (Stereo/Mono)
Screen Mode
Select the aspect ratio of TV which is connected to
STB (4:3 or 16:9).
Display Format
Select the format which the video is to be displayed on screen.
When your TV set is 4:3 and video source is 16:9,
STB will display in Letter-box or Centre mode as selected.
When your TV set is 16:9 and video source is 4:3,
STB will display in the Pillar-box or Full mode as selected.
GB22
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
UHF Tuning
You select the STB output by using the UHF channel.
Channel
Select an UHF channel. The range of channels and frequency
value are different for each PAL Standard:
PAL I/G for Europe
: CH21 ~ CH69
PAL B for Europe/Australia : CH28 ~ CH69
PAL D for China
PAL K for Russia
: CH13 ~ CH62
: CH21 ~ CH69
PAL Standard
Select a PAL Standard according to the above range of channels.
Offset
Adjust the fine tuning value. The Offset ranges from -4 to +4 and
each Offset represents 1MHz.
GB23
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Setting
Select the OSD Transparency, Information Box Display Time and
so on.
OSD Transparency
Select the OSD Transparent type. It affects Information box,
Soundtrack, Subtitle, Service list, Time and Quick mode of
TV Guide. Use the
buttons to toggle transparent, opaque,
20%, 40%, 60% and 80%.
Info. Box Display Time
Set the display duration of Information box displayed on the screen
after changing services. The time ranges from 0 to 20 seconds.
Menu Background
Set the type of background for the menu to be displayed on.
Changing to Reserved Service
When the reserved time has come during the view of services:
• Manual Mode
This mode shows the message “A reserved event has started on
another service. Press OK to view the reserved service. Press
EXIT to ignore reserved service. (will automatically change after
10 seconds.)” And ask the presence of change and then makes a
change.
• Auto Mode
The current service will be automatically changed to the
time-reserved service.
GB24
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
4-2. Service Organising
This menu gives users access to options that allow them to
organise their TV Services, Radio Services and Networks.
0 0 0 0
** The default PIN code is
.
Organise TV Services
Organise All Services
This mode allows users to Delete, Move, Lock, Skip and Rename
TV Services.
• Delete
1. Press the RED(
)button to delete unwanted services.
2. Highlight the services that you want to delete in grey.
3. Press the
4. Press the
button to confirm.
button to cancel the deletion.
• Move
1. Press the GREEN(
)button to move the service to where you
want to locate. Then, the icon( ) will be displayed in front of the
service number.
2. Use the
3. Press the
4. Press the
buttons to select a new location.
button to fix the location.
button to return to the original location.
• Lock
1. Press the YELLOW(
)button to lock services.
Then, the symbol “ ” will be displayed at the right side of the
service name.
2. Enter the PIN code to view the locked services.
• Skip
1. Press the BLUE(
Then, the symbol “
service name.
)button to skip services.
” will be displayed at the right side of the
2. Use NUMERIC buttons(0~9), service list or
button to view the
buttons.
skipped services when selecting channels.
Note : You can’t view the skipped services by using
GB25
Download from Www.Somanuals.com. All Manuals Search And Download.
• Rename
1. Press the WHITE(
)button to change the service name.
Then, the keyboard image will be displayed on the screen.
2. Key in the new service name.
You can use the four direction keys to move or select the
services.
: to move the previous service
: to move the next service
: to move back by 10 services
: to move forwards by 10 services
Note : The box between service list and the description of the
colour buttons offers the brief information of a service
where the cursor is located.
Organise Favourite A~D
Each of TV and Radio has four Favourite groups.
Each Favoruite group contains up to 100 services.
Delete, Move, Lock, Skip or Rename each TV service in a
Favourite TV group and re-group them into your Favourite TV group.
This mode has the same operating methods as “organise all
services”.
• When you delete a service in the Favourite group, it will be
available again on the All TV service list. This allows the service
to be removed from the Favourite group.
• You can move the service only within the Favourite group.
• Coloured keys are available when the cursor is located in the
middle window.
(Except when the middle window is disabled(grey).)
To select the Favourite group;
1. Use the
button to move the cursor to “Gr.”-plate(left).
2. Select the wanted favourite group.
To group the services into Favourites;
1. Use the
button to move the cursor to “Services”-plate(right).
2. Select the service you want to group into Favourites.
3. Press the
4. Use the
5. Press the
button.
button to move the cursor to “Favourites”-plate(left).
button to save the selected group.
Note : 1. Use the
buttons to move the cursor.
2. Use the
buttons to select the previous or next page.
GB26
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
Organise Service Genre
The Organise Service Genre feature allows the user to Delete/
Lock/Skip/Rename a service in the selected Genre.
Available genre : Movie, News, Show, Sports, Children, Music, Art,
Education, etc.
The colour buttons function same as ones for Organise All services
except the following differences:
• When you delete a service in the selected genre, it will be
available again on the All TV services list at the right side.
At that time, the genre for the deleted service becomes “etc”.
• You can move the service only in the selected genre.
• Coloured buttons are available when the cursor is located in the
middle window.
To select the Genre;
1. Use the button to move the cursor to “Gr.”-plate(left).
2. Select the wanted genre.
To group the services into a Genre;
1. Use the button to move the cursor to
“Services”- plate(right).
2. Select the service you want to group into Genre.
3. Press the
4. Use the button to move the cursor to “Genre”-plate(left).
5. Press the button to save the selected group.
button.
Note : 1. Use the
buttons to move the cursor.
2. Use the
buttons to select the previous or next page.
GB27
Download from Www.Somanuals.com. All Manuals Search And Download.
Organise Radio Services
The Organise Radio Services functions same as TV Services
except that it uses Radio Services.
You can delete or move Radio Services and change the attributes
of them.
Organise All Services
The Organise All Services lets the user Delete, Move, Lock, Skip or
Rename Radio services on the All Radio services list.
Organise Favourite A-D
The Organise Favourite A-D lets the user Delete, Move, Lock, Skip
or Rename Radio Services from the Favourite Radio Services and
group into a new Favourite Radio Services.
The Radio Services are grouped into a Favourite in the same way
as the TV Services(refer to page GB20).
Organise Service Genre
The Organise Service Genre lets the user Delete, Lock, Skip or
Rename Radio Services and group into Radio Service Genres.
Radio Genres include : Pop, Rock, Country, Classic, Jazz, Folk,
News, Show, Sports, Education, User A-D,
etc.
The Radio Services are grouped into a Genre in the same way as
the TV Services (refer to page GB21).
Organise Networks
You can edit services using the network unit.
• The provider names are displayed on the left side of screen,
and the TV/Radio Services included in the highlighted
Network are displayed on the right side of screen.
Only the Delete, Move, Rename Function can be used
in this mode.
• When TV/Radio Services are too many to be displayed, use
the button to move the cursor to the right window and use
the
and
buttons to move the cursor to the next list.
When the number of services is under 10, the scroll bar is not
displayed. In Radio Service icon(
number.
) is marked in front of service
GB28
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
4-3. Service Searching
A service is transmitted in a transport stream. To watch the service,
all services in the transport stream should be searched and stored in
this menu. The proper information to search the stream is
provided by the network operator. Please contact your installer
or the network operator.
0 0 0 0
** The default PIN code is
.
Easy Search
The services can be searched with minimal information in this menu,
“Easy Search”. But it takes more time, if the parameters are set as
“Auto”. To search the services quickly, please give proper information
for each items.
Channel
Select the number of VHF/UHF channel, in which the transport
stream is transmitted by using the
buttons or the
NUMERIC buttons(0~9). If the number is not correct, STB will fail
to search any service.
Mode
Select the proper item within “2K FFT”, “8K FFT” and “Auto” by using
the
buttons. If the information is not known, then “Auto” can be
selected. But this takes slightly longer time if “Auto” is selected.
Guard Interval
Select the proper item within “1/4”, “1/8”, “1/16”, “1/32” and “Auto”
by using the
buttons. If the information is not known, then
“Auto” can be selected. But this takes slightly longer time.
Hierarchy
Select the proper item within “None”, “alpha=1”, “alpha=2”, “alpha=4”
and “Auto” by using the
buttons. If the information is not know,
then “Auto” can be selected. But this takes longer time.
Network Search
Select the option “YES” to search all services in the network.
Then, after STB succeeds to lock to the signal, STB will get proper
information on the services in the other channels and stores the
information automatically. If the network operator does not
transmit proper information in the default channel, STB can not
search all services. It is required to search for all channels manually.
GB29
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Search
The menu, “Custom Search” operates similar as the menu
“Easy Search”, however more parameters are required to search the
services. Select proper items as follows. To get proper information,
please contact your installer or the network operator.
Frequency
Enter the exact frequency (kHz) of the channel, in which a transport
stream is transmitted.
Mode
Select the proper item within “2K FFT”, “8K FFT” and “Auto” by using
the
buttons. If the information is not known, then “Auto” can be
selected. But this takes slightly longer time if “Auto” is selected.
Guard Interval
Select the proper item within “1/4”, “1/8”, “1/16”, “1/32” and “Auto”
by using the
buttons. If the information is not known, then
“Auto” can be selected. But this takes slightly longer time.
Hierarchy
Select the proper item within “None”, “alpha=1”, “alpha=2”, “alpha=4”
and “auto” by using the
buttons. If the information is not know,
then “Auto” can be selected. But this takes longer time.
Constellation
Select the proper item within “QPSK”, “16-QAM”, “64-QAM” and
“Auto” by using the
buttons.
Stream
Select the proper item within “HP”, “LP” and “Auto”. This item is
deactivated when Hierarchy is “Auto” or “None”.
Code Rate
Select the proper item within “1/2”, “2/3”, “3/4”, “5/6”, “7/8” and “Auto”
by using the
buttons. “Auto” is recommended, if Hierarchy is
set as “Auto”.
Frequency Offset
Select the proper item within “No Offset”, “+1/6 MHz”, “-1/6 MHz” and
“Auto” by using the
buttons. “Auto” is recommended.
GB30
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
Network Search
Select the option “YES” to search all services in the network.
Then, after STB succeeds to lock to the signal, STB will get proper
information on the services in the other channels and stores
the information automatically. If the network operator does not
transmit proper information in the default channel, STB can not
search all services. It is required to search for all channels
manually.
Automatic Search
The menu "Automatic Search" is the easiest method to store new
stations. Proceed as follows in order to start the Automatic Search:
Start Channel
Set the lowest channel in your area by using the
Press the button to start the search.
buttons.
End Channel
Enter the highest channel by using the
buttons.
Press the
button to start the search.
Default Search
The Default Search searches the services refering to the predefined
channel list. The channel list can be chosen according to the region
where the search is performed.
If the region is chosen in the menu, the channels are automatically
scanned to search services.
Note : The Default Search deletes all stored services.
GB31
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4. Status
STB Status
Displays the information of H/W Version, S/W Version and
Loader Version of STB and so on.
Signal Detection
Shows the Signal Level(AGC level) and Signal Quality(BER) of the
current service and is help to the initial antenna setting.
STB Upgrade
You can download and upgrade the software of this STB via
Transmiting station when the software of new version is released.
Do not turn off the STB during downloading.
When the power is switched OFF, turn on the STB and the process
will be continued.
GB32
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide of Main Menu
4-5. Conditional Access(For Nagravision Embedded)
This menu allows the user to view the information on the
Smart card and Nagravision Conditional Access system such as
version and serial number of Smart card.
• F1-4000T models are not applicable.
PPV purchase list
If you perchased events in advance, the entitlements of Pay Per
View events will be displayed. (ID, event name, service name,
start time, status and cost)
Credit information
Displays the Credit information. (ID, credit and status)
System information
Displays the System information.
(Smart card serial number, IRD serial number, Smart card version,
Smart card revision, Conditional Access software version,
Conditional Access software revision.)
5. Utility
STB supports additional functions such as Calendar and
Biorythm.
At the Biorhythm use the
buttons to adjust your birth
year and date to see your current biorhythm status.
GB33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
GB34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Map
GB35
Download from Www.Somanuals.com. All Manuals Search And Download.
GB36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Conditional Access Interface
Nagravision Embedded
1 Slot Smart card
• F1-4000T models are not applicable.
Tuner & Channel
Input Connector
Input Channel
Input RF Power Level
Demodulation
Mode
IEC 169-2, Female
VHF/UHF
-70 dBm ~ -20 dBm
OFDM
2 K, 8 K and Auto
1/2, 2/3, 3/4, 5/6, 7/8 and Auto
1/4, 1/8, 1/16, 1/32 and Auto
FEC Decode
Guard Interval
MPEG Transport Stream A/V Decoding
Transport Stream
MPEG-2 ISO/IEC 13818
Transport stream Specification
MPEG-2 MP@ML
Profile Level
Input Rate
15 Mbit/s Max
Aspect Ratio
Video Resolution
Audio Decoding
Audio Mode
Sampling
4:3, 16:9
720 x 576
MPEG/MusiCam Layer I & II
Single channel/Dual channel/Joint stereo/Stereo
32, 44.1 and 48 KHz
Memory
Main Processor
Flash Memory
Graphic(MPEG) &
System DRAM
TMIPS R3930(81 MHz)
2 Mbyte(F1-4000T)
4 Mbyte
3 Mbyte(NA-4710T)
Data rate decides the picture quality of digital TV programmes.
Data rate of about 5-6 Mbit/s coincides with the picture quality of a analog TV programme.
GB37
Download from Www.Somanuals.com. All Manuals Search And Download.
A/V & Data In/Out
TV SCART
Video Output(CVBS, S-Video, RGB)
Audio Output
(Resolution : 20 bits DAC, Max. 2 Vrms)
Video Output(CVBS)
VCR SCART
Video Input(CVBS, S-Video, RGB)
Audio Output(Resolution : 20 bits DAC, Max. 1 Vrms(fixed))
RCA/Cinch, Video Output(CVBS)
RCA/Cinch Volume and Mute Control
(Resolution : 20 bits DAC, Max. 2 Vrms)
Transfer rate Max. 115Kbps, 9pin D-sub Type
VIDEO
AUDIO R/L
RS-232C
RF-Modulator
RF/Loop Through Output
Frequency
IEC, Male
470 - 862 MHz
Output Channel
TV Standard
Preset Channel
CH21-69 for UHF Modulator
PAL I/G/B/D/K selectable by Menu setting
CH36 (or TBD). Software changable by Menu
Power Supply
Input Voltage
Type
AC 90 - 250 V, 50/60 Hz (SMPS type)
SMPS
Power Consumption
Standby Power
Protection
Max. 20 W
≤
11W
Separate internal fuse. The input shall have lightening Protection
Physical Specification
Size (W
x
H
x
D)
310
x
60
x
235 mm
Weight (Net)
Around 2.2 kg
Operating Temp
Storage Temp
0°C to + 45°C
-10°C to + 70°C
Storage Humidity
5% ~ 95% RH (Non-Condensing)
•
Please note : The specification of the STB may be changed without notice in advance.
GB38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|