ꢀꢁꢂ
®
IBM Ethernet Switch B24X
IBM System x at-a-glance guide
The IBM Ethernet Switch B24X is a compact, high-performance, high-availability, and high-density 10
GbE solution that meets mission-critical data center and High Performance Computer (HPC)
requirements. It can support 1 GbE servers until they are upgraded to 10 GbE-capable Network Interface
Cards (NICs), simplifying migration to 10 GbE server farms.
In addition, the B24X is a fully featured switch with IPv4 Layer 3 capabilities that can provide cost-efficient
10 GbE network aggregation for 1 GbE access switches. The switch runs a feature-rich and mature
IronWare Operating System with an industry-standard command-line interface (CLI), minimizing
re-training and operational costs. Supporting a full range of Request for Comments (RFC) and Institute of
Electrical and Electronics Engineers (IEEE) standards for interoperability, along with compatibility for
vendor-specific protocols such as Cisco Discovery Protocol (CDP) and Per-VLAN Rapid Spanning Tree
Plus (PVRST+), the B24X integrates seamlessly into existing network infrastructures.
Figure 1. IBM Ethernet Switch B24X (front view)
Figure 2. IBM Ethernet Switch B24X (back view)
Did you know
The IBM Ethernet Switch B24X is the most power-efficient 10 Gbps switch in its class at 176 watts per
twenty-four 10 GbE ports. This saves customers up to 56% in power and cooling costs over competing
switches. In addition, the high-performance, cut-through, full-mesh non-oversubscribed (1:1) architecture
of the B24X offers up to twice the performance with lower latencies and uses up to 2 - 3 times less rack
space.
The no-compromise B24X also features data center class network resiliency and hardware availability
features to support non-stop networking, making the switch ideal as an all-purpose Top of Rack switch
IBM Ethernet Switch B24X
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power cords are not included and must be specified at the time of order. The B24X has a C14 inlet to
receive a C13 power plug. Table 2 lists the available power cable options.
Table 2. Power cord options
Part
number
Description
Line cord – 2.8 m, 10A/230V, C13 to CEE7-VII (Europe)
Line cord – 2.8 m, 10A/250V, C13 to DK2-5a (Denmark)
Line cord – 2.8 m, 10A/250V, C13 to SEV 1011-S24507 (Swiss)
Line cord – 2.8 m, 10A/250V, C13 to SI 32 (Israel)
39Y7917
39Y7918
39Y7919
39Y7920
39Y7922
39Y7923
39Y7924
39Y7925
39Y7927
39Y7928
39Y7929
39Y7930
39Y7931
39Y7932
39Y7937
Line cord – 2.8 m, 10A/250V, C13 to SABS 164 (S. Africa)
Line cord – 2.8 m, 10A/250V, C13 to BS 1363/A (UK)
Line cord – 2.8 m, 10A/250V, C13 to AS/NZ 3112 (Australia/NZ)
Line cord – 2.8 m, 220-240V, C13 to KETI (S. Korea)
Line cord – 2.8 m, 10A/250V, C13 to (2P+Gnd) (India)
Line cord – 2.8 m, 220-240V, C13 to GB 2099.1 (China)
Line cord – 2.8m, 125V, C13 to NBR 6147 (Brazil)
Line cord – 2.8 m, 10A/250V, C13 to IRAM 2073 (Australia)
Line cord – 4.3 m, 10A/125V, C13 to NEMA 5-15P (US)
Line cord – 4.3 m, 10A/100-250V, C13 to IEC 320-C14
Line cord – 1.5 m, 10A/100-250V, C13 to IEC 320-C14
Each SFP+ optical transceiver, such as the 10GBASE-SR SFP+, requires fiber optic cabling with duplex
LC connectors to connect to another optical transceiver. See the “Network cabling requirements” section
for additional details.
Each 10/100/1000 MbE RJ-45 port or the 1 GbE copper SFP transceiver (1000BASE-T) requires copper
CAT 5e or higher cabling for connectivity. Table 3 lists the available copper cable options.
Table 3. Ethernet copper cable (RJ-45) options
Description
IBM part number
40K5679
0.6 m Ethernet cable (blue)
1.5 m Ethernet cable (blue)
3 m Ethernet cable (blue)
10 m Ethernet cable (blue)
25 m Ethernet cable (blue)
40K8785
40K5581
40K8927
40K8930
IBM Ethernet Switch B24X
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional options are available through IBM System Networking HVEC channels. Table 4 lists the
orderable part numbers for these additional options.
Table 4. IBM part numbers and feature codes for ordering (System Networking HVEC)
Description
IBM part
number
IBM feature
code
10 GbE Direct Attach SFP+, 1 m, Active TwinAx copper cable
10 GbE Direct Attach SFP+, 3 m, Active TwinAx copper cable
10 GbE Direct Attach SFP+, 5 m, Active TwinAx copper cable
45W2398
45W2408
45W3039
2711
2731
2751
1 GbE 100 m SFP, 1000BASE-T (RJ-45, connects to CAT5 or
higher cabling)
45W2813
2202
1 GbE 550 m SFP, 1000BASE-SX (duplex LC, MMF, 850 nm, OM)
1 GbE 10 km SFP, 1000BASE-LX (duplex LC, SMF, 1310 nm, OM)
45W2815
45W2816
2211
2212
2213
2131
1 GbE 70 km SFP, 1000BASE-LHA (duplex LC, SMF, 1550 nm, OM) 45W2817
10 GbE 10 km, SFP+, 10GBASE-LR (duplex LC, SMF, 1310 nm, 45W4264
OM)
Note: OM = Optical Monitoring supported. SMF = single-mode fiber. MMF = multi-mode fiber. MMF
distance supported depends on cabling type. Use OM3 50 ìm (2000 MHz*km) MMF to support the farthest
distances.
The B24X has twenty-four dual-speed 10/1 GbE SFP+ ports enabling customers to seamlessly transition
their 1 GbE devices to 10 GbE speeds by upgrading the transceiver. Qualified SFP+ or SFP transceivers
are required for each SFP+ port and are not included. Up to twenty-four 10 GbE SFP+ or 1 GbE SFP
transceivers are supported on each IBM Ethernet Switch B24X.
10 GbE SFP+ optical –SR (10GBASE-SR) transceivers support distances up to 300 m, which is ideal for
connectivity within a data center. 10 GbE SFP+ optical –LR (10GBASE-LR) transceivers support extended
distances up to 10 km.
Figure 3. SFP+/SFP optical transceiver - Receives duplex LC connectors
IBM Ethernet Switch B24X
4
Download from Www.Somanuals.com. All Manuals Search And Download.
For cost-effective server connectivity within a rack, 10 GbE copper direct attach SFP+ active TwinAx
cables are available. These cables have two 10 GbE SFP+ transceivers attached on either end of the
cable and have been tested for compatibility with the Brocade 10Gb CNA, QLogic 10Gb CNA, and
Emulex 10Gb Virtual Fabric Adapter for IBM System x. Compatibility with other 10 GbE server adapters
and network devices is up to the user to determine.
Figure 4. 10 GbE Direct Attach SFP+ TwinAx cable
Features and benefits
The features and benefits are:
z
Comprehensive standards support: Supporting a wide range of open IEEE and RFC standards, the
B24X is fully interoperable with existing network environments. In addition, the B24X supports
vendor-specific protocols such as Cisco Discovery Protocol (CDP), native support for Per-VLAN
Rapid Spanning Tree Plus (PVRST+), and static trunks to EtherChannel for further supportability.
z
z
Built for the data center: The B24X features front-to-back airflow, allowing installation into racks with a
hot-cold aisle design without the need for complicated air baffles. All ports are found on the front side
of the switch for easy serviceability.
Flexible deployment: Dynamic Layer 3 routing allows the B24X to support multiple deployment
options, including a Top of Rack access switch supporting inter-VLAN routing within a rack or a
cost-effective aggregation switch.
z
z
High availability: Hot-swappable and redundant power supplies and fan trays reduce downtime and
allow you to meet your service level agreements by increasing switch availability.
Best-in-class power efficiency: At only 176 W per twenty-four 10 GbE ports, the low power
consumption reduces operational costs tied to power and cooling and allows data centers running out
of power to deploy more assets.
z
High performance: Supporting full-line rate traffic on all ports with no over-subscription and 488 Gbps
of internal forwarding performance, the B24X also uses an advanced cut-through forwarding
architecture featuring low latencies to support time-sensitive applications such as real-time video and
market trading/exchange applications.
z
z
Industry-standard CLI: Minimize re-training and personnel costs while increasing operational
efficiencies by utilizing a management interface with which the network team is already familiar.
Mature operating system: The feature-rich and time-tested IronWare Operating System running on
the B24X and all IBM b-type system networking devices provides a consistent experience across the
network.
z
Upgrade without rip-and-replace: With dual-speed 10/1 GbE SFP+ ports plus four additional 1 GbE
RJ-45 ports, the B24X supports a mix of 10 GbE and 1 GbE servers on the same switch without
needing to force upgrades of existing systems.
IBM Ethernet Switch B24X
5
Download from Www.Somanuals.com. All Manuals Search And Download.
z
z
Granular network visibility: Hardware-based sFlow v5 provides packet sampling for analysis, trending,
and application of automated policies based on thresholds using industry applications such as
Brocade Ironview Network Manager.
Cost competitive: The B24X includes all software capabilities and a 3-year warranty of the base
product, simplifying ordering while being priced extremely competitively compared with other vendors.
Specifications
The IBM Ethernet Switch B24X supports the following specifications when running IronWare R04.2.x and
higher. Be aware that Layer 3 capabilities are supported on IronWare R04.2.x and higher, and further
details can be found by navigating the IBM Support website:
z
Form-factor
z
z
1 RU; 43.5 cm (17.1 in.) width x 4.28 cm (1.7 in.) height x 39.4 cm (15.5 in.) depth
Rack-mount into 19” EIA-310D compliant rack, Telco rack, or table-top
z
z
z
Ports (data)
z
z
Twenty-four dual-speed 10/1 GbE SFP+ ports
Four 10/100/1000 MbE RJ-45 ports
Ports (management, out-of-band)
z
z
One10/100/1000 MbE RJ-45 port
One DB9 male serial console port
Power supplies, fans, and airflow
z
Two 300 W AC hot-swappable power supplies supported for 1+1 redundancy (base switch
comes with one)
z
z
One hot-swappable fan tray with three 2+1 redundant fans
Front-to-back airflow supporting data center hot-cold aisle deployments
z
Performance
z
z
z
488 Gbps line speed full-duplex throughput
363 Mpps forwarding capacity
1.5 micro-second latency
z
z
z
Jumbo frames
z
Supported: up to 9216-byte Ethernet frame sizes
Media (transceivers)
z
10 GbE SFP+ -SR transceivers and direct attach copper TwinAx cables available
VLANs
z
z
z
z
z
z
z
Up to 4096 maximum VLANs
802.1Q tagging
802.1Q-in-Q tagging
Dual-mode VLANs (tagged and untagged traffic across same port)
Port-based VLANs
VLAN groups
Private VLANs
IBM Ethernet Switch B24X
6
Download from Www.Somanuals.com. All Manuals Search And Download.
z
z
Link aggregation
z
z
z
Up to eight links per group, 28 link groups per switch
Static trunks compatible with Cisco EtherChannel
802.3ad Link Aggregation Control Protocol (LACP) for dynamic trunk groups
Quality of service (QoS) and rate shaping
z
Eight queues per port with strict priority (SP), weighted round robin (WRR), and combined
SP/WRR schedulers
z
z
z
z
z
802.1p Class of Service (CoS)
IP DSCP/DiffServ (Type of Service) to priority mapping
ACL, port, and static MAC address to priority mapping
Layer 2 CoS and Layer 3 DSCP re-marking
Outbound rate shaping
z
Layer 2
z
z
Up to 32,000 MAC addresses.
Per-VLAN Rapid Spanning Tree Protocol Plus (PVST/PVST+/PVRST+) compatibility in
default configuration supports smooth implementation into Cisco Layer 2 environments.
z
z
z
802.1d Spanning tree Protocol (STP).
802.1w Rapid Spanning Tree Protocol (RSTP).
802.1s Multiple Spanning Tree Protocol (MSTP) enables multiple STP instances and
forwarding paths for more efficient traffic distribution.
z
z
Virtual Switch Redundancy Protocol (VSRP) alternative to STP and includes sub-second
convergence and Layer 2 redundancy based on the VRRPE protocol.
Metro Ring Protocol (MRP) v1/v2 enables fast, sub-second convergence in ring topologies.
IGMPv1/v2/v3 Snooping and PIM-SM Snooping reduce multicast flooding in a Layer 2
network.
z
z
z
Root Guard prevents rogue devices from hijacking STP root.
BPDU Guard prevents rogue devices from participating in STP.
DHCP Assist helps DHCP servers respond correctly to devices in a different subnet than the
DHCP server.
z
Layer 3
z
z
z
z
z
z
z
Up to 12,000 IPv4 routes
Routing Information Protocol (RIP) v1/v2
Open Shortest Path First (OSPF) v2
Internet Group Management Protocol (IGMP) v1/v2/v3
Protocol Independent Multicast Dense Mode (PIM-DM) v1/v2 and Sparse Mode (PIM-SM) v2
Equal Cost Multi Path (ECMP) for load balancing across up to eight paths
Virtual Router Redundancy Protocol (VRRP) and VRRP-E (Enhanced)
IBM Ethernet Switch B24X
7
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Security
z
802.1x authentication, accounting, port security, and dynamic assignment for ACLs, MAC
filtering, and VLANs
z
z
z
z
Up to 1,534 inbound, rule-based (hardware-based) access control list (ACL) entries
Standard ACLs based on source IP address
Extended ACLs based on source and destination IP addresses or IP protocol information
Authorization, Authentication, and Accounting (AAA) support on RADIUS, TACACS, and
TACACS+
z
Multi-device authentication, which validates and applies security policies based on MAC
address information from a RADIUS server
z
z
AES encryption for SSHv2
Denial of Service protection against Smurf (ICMP) and TCP SYN attacks in hardware
z
Management
z
z
z
Industry-standard CLI via Telnet and SSHv2
Fault management integration with IBM Systems Director v6.2
Network-wide management of all IBM b-type system networking switches using Brocade
Ironview Network Manager (INM)
z
z
Simple Network Management Protocol (SNMP) v1/v2/v3
sFlow v5 for hardware-based packet sampling
z
Ties into industry tools such as Brocade INM and InMon products for trend analysis
and automated policy application
z
z
Remote Monitoring (RMON) protocol
Link Layer Discovery Protocol (LLDP), Cisco Discovery Protocol (CDP), and Foundry
Discovery Protocol (FDP)
z
z
Simple Network Time Protocol (SNTP)
Firmware image update via TFTP and SCP
z
Monitoring
z
z
z
Syslog support of up to six Syslog servers for centralized log collection and analysis.
Port mirroring of inbound and outbound traffic.
Digital optical monitoring monitors power levels and temperatures of optical transceivers and
sends an alert if operating out of specification.
z
z
Temperature monitoring sends alerts if the temperature exceeds a certain threshold and
shuts down the device after an extended period of time.
Port flap dampening increases network resiliency by limiting the number of port state
transitions on an interface.
z
z
Link Fault Signaling (LFS) detects and reports fault conditions on 10 GbE ports.
Uni-Directional Link Detection (UDLD) monitors the link between two devices and brings the
port down if the link goes down on either end.
IBM Ethernet Switch B24X
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectivity options
The B24X supports a wide variety of industry IEEE and RFC standards and should interoperate with any
network device that supports industry standard Ethernet connectivity. This includes servers, other
Ethernet switches, iSCSI Storage Area Network (SAN) arrays, Network-Attached Storage (NAS) arrays,
and other network devices. Figure 5 shows the IBM Ethernet Switch B24X (front view with port labeling).
Figure 5. IBM Ethernet Switch B24X (front view with port labeling)
IBM Ethernet Switch B24X
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5 lists the methods that the B24X can use to connect to another device.
Table 5. Connectivity options
On the B24X
On the device to be connected
SFP+ port using 10 GbE SFP+ optical The optic on the device being connected can be
transceiver: 69Y0389: 10GBASE-SR
another form-factor (that is, XFP transceiver, X2
module, or integrated into NIC), but must have a
matching optical transmission type.
This optical transceiver receives a
duplex LC connector.
For example, a 10GBASE-SR XFP optical
transceiver on the device being connected must
match a 10GBASE-SR SFP+ optical transceiver on
the B24X within the proper wavelength and power
specifications.
Multi-mode or single-mode fiber as specified
required for connectivity. See the "Network cabling
requirements" section.
SFP+ port using 10 GbE Direct Attach It is up to the user to decide whether the interface
SFP+ Active TwinAx cable:
on the device being connected supports the IBM
DAC used with the B24X.
z 45W2398 or 45W2401: 1 meter
z 45W2408 or 45W2409: 3 meter
z 45W3039 or 45W3042: 5 meter
Below is a list of IBM server adapters that have
been tested for compatibility with the part numbers
in the left-hand column. If a product is not listed,
that does not necessarily mean that it is
Direct Attach Cables (DACs) are
copper cables with two SFP+
transceivers attached to either end of
the cable.
incompatible--it simply has not been tested.
IBM server adapters:
z 42C1820: Brocade 10Gb Converged Network
Adapter for IBM System x
z 49Y4250: Emulex 10Gb Virtual Fabric Adapter
for IBM System x
z 42C1800: QLogic 10 Gb CNA for IBM System x
10/100/1000 MbE RJ-45 port:
Auto-sensing, auto-negotiating,
auto-MDI/MDIX.
Connect to any RJ-45 port or TX adapter
supporting 10, 100, or 1000 Mbps Ethernet over
CAT5 or higher cabling up to 100 meters.
Connectivity to IBM System servers
The B24X can be deployed as a Top of Rack access switch to provide connectivity to servers within a
rack. This includes servers from IBM System x, System p, and System i.
IBM System x servers typically come with on-board 1 Gbps Ethernet RJ-45 ports. Additional 1 GbE NICs
can be installed to increase connectivity. These NICs might have RJ-45 ports, SFP ports requiring a
transceiver, or integrated optical transceivers. Follow the guidelines in Table 5 for connectivity.
IBM Ethernet Switch B24X
10
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Gbps Ethernet connectivity is not standard in most System x servers, and a 10 GbE NIC or 10 GbE
CNA must be installed. Only the IBM System x3850/3950 X5 series (except for the ARx model) come
standard with a customized Emulex Virtual Fabric Adapter. Table 6 lists the 10 GbE adapters that are
available for IBM System x servers.
Table 6. 10 Gbps adapters for IBM System x servers
System x
rack and
tower
server
adapter
models
Brocade
10Gb
CNA
(42C1820
)
N0.
22
6
N
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
QLogic
10Gb
CNA
(42C1800
)
Y
Y
Emulex
Virtual
Fabric
Adapter
(49Y4250
)
NetXtrem
e II 10
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
GigE
Express
Fiber SR
Adapter
(42C1790
)
The Brocade 10Gb CNA [42C1820], QLogic 10Gb CNA [42C1800], and Emulex Virtual Fabric Adapter
[49Y4250] each have two SFP+ ports and can be connected to the B24X using:
z
The adapter’s supported 10GBASE-SR SFP+ transceiver connected to the B24X 10GBASE-SR
SFP+ transceiver [69Y0389] over multi-mode fiber cable.
z
The Direct Attach SFP+ Active TwinAx copper cables listed in Table 4.
The NetXtreme II 10 GigE Express Fiber SR Adapter (42C1790) has a single integrated 10GBASE-SR
optic. This port can be connected to the B24X 10GBASE-SR SFP+ transceiver [69Y0389] over a
multi-mode fiber cable.
Connectivity to IBM BladeCenter
The B24X can be deployed as an aggregation switch to provide connectivity between down-stream
IBM Ethernet Switch B24X
11
Download from Www.Somanuals.com. All Manuals Search And Download.
switches. This includes IBM System Networking switches, BladeCenter Ethernet embedded switches, and
Ethernet switches from other vendors
IBM BladeCenter Ethernet Switch Modules are available with 1 Gbps and 10 Gbps Ethernet uplinks.
Table 7 lists the various IBM BladeCenter Ethernet Switch Modules that can be used to connect to the
B24X.
Table 7. IBM BladeCenter Ethernet Switch Modules (ESM)
BladeCenter Ethernet
Switch Module models
Ext. 1
GbE
ports
Ext. 10
GbE
ports
Part #
BC H
Y
BC HT
BC E
N
BC T
N
BC S
N
BNT Virtual Fabric 10Gb
ESM
46C71
91
10 dual-speed
SFP+
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Cisco Nexus 4001I ESM
46M6
071
6 dual-speed
SFP+
Y
N
N
N
1 X21
0
Cisco Catalyst 3110X ESM 41Y85
22
Y
Y
Y
N
10Gb Ethernet Pass-Thru
Module
46M6
181
0
14
SFP+
Y
N
N
N
BNT 1/10Gb Uplink ESM
44W4
404
6
3 SFP+
Y
Y
Y
Y
RJ-45
BNT Layer 2/3 Copper
ESM
32R18
60
6
0
0
0
0
0
0
0
Y
Y
Y
Y
RJ-45
BNT Layer 2/3 Fiber ESM
32R18 6 SFP
61
Y
Y
Y
Y
BNT Layer 2-7 Gigabit
ESM
32R18
59
4
Y
Y
Y
Y
RJ-45
Cisco Catalyst 3012 ESM
43W4
395
4
Y
Y
Y
Y
RJ-45
Cisco Catalyst 3110G
ESM
41Y85
23
4
Y
Y
Y
N
RJ-45
Server Connectivity
Module
39Y93
24
6
Y
Y
Y
Y
RJ-45
Intelligent Copper
Pass-Thru Module
44W4
483
14
RJ-45
Y
Y
Y
Y
Note 1: X2 modules have duplex SC connectors. An SC-to-LC fiber cable is required to connect to a SFP+
transceiver with duplex LC connectors.
For Ethernet Switch Modules with SFP+ or X2 ports see the respective IBM Redbooks at-a-glance guide
to locate transceivers supported. Review Table 5 for guidance on how to connect the Ethernet Switch
Module to the B24X.
Popular configurations
This section illustrates how the IBM Ethernet Switch B24X can be used in various configurations.
IBM Ethernet Switch B24X
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Top of Rack switch
An access or edge switch is a switch that connects directly to the end devices requiring network
connectivity, most commonly servers and storage arrays in the data center. A switch that is 1 or 2 RU in
height that acts as the access switch for devices within a rack is commonly called a Top of Rack switch.
The B24X is ideal for deployment as an all-purpose Top of Rack switch in demanding network
environments due to its high-performance, resilient hardware characteristics and comprehensive network
features support. The B24X can also be used to support NAS or iSCSI SAN storage in a shared or
dedicated network environment (Figure 6).
Figure 6. IBM Ethernet Switch B24X as Top of Rack switch with server and storage connections
IBM Ethernet Switch B24X
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8 outlines the components used in Figure 6.
Table 8. Components used in reference to Figure 6
Diagram
reference
Part number/
machine type
Description
Quantity
2
0563-012
IBM Ethernet Switch B24X
IBM System x server with 10 GbE NIC/CNAs
z See Table 5 for additional details.
z Other vendor servers can be used.
Varies
16
NAS array
Varies
Varies
Existing network infrastructure, which can
include IBM Systems Networking devices and
other standards-compliant Ethernet/IP switches
and routers
Varies
-
0563-012
Varies
IBM Ethernet Switch B24X
iSCSI SAN array
2
Varies
Solution details are:
z
z
z
z
Forty-one rack units (with two RU servers)
1:1 subscription ratio within rack
2.43:1 over-subscription ratio to rest of network
Connectivity to NAS or iSCSI SAN (or both) for mid-range scalable storage
In the solution shown in Figure 6 we have two IBM Ethernet Switch B24Xs providing connectivity to all
devices within a single rack. Within the rack we have a mix of servers with 10 GbE connections to each
B24X for redundancy. The B24X can also be used to connect to NAS arrays for scale-out file sharing and
also to a separate iSCSI SAN for dedicated storage access as bandwidth and security needs require.
IBM Ethernet Switch B24X
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Network device connections
Figure 7 shows an example of the types of options that can be used to connect separate devices to the
IBM Ethernet Switch B24X
Figure 7. IBM Ethernet Switch B24X device connections
IBM Ethernet Switch B24X
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 9 outlines the components used in Figure 7.
Table 9. Components used in reference to Figure 7
Diagram
reference
Part number/
machine type
Description
Quantity
2
IBM Ethernet Switch B24X
0563-012
IBM x3850/x3960 X5 (except ARx model)
z Comes with 2-port 10 GbE (SFP+) Emulex
Virtual Fabric Adapter.
z Use a single Direct Attach cable (TwinAx)
to connect to B24X, available in 1, 3, or 5
meters. (See Table 4.)
Varies
-
NAS or iSCSI storage array
Varies
Varies
Cisco Catalyst 3110X Ethernet Switch Module
z On 3110X, use X2-10GB-SR=
(10GBASE-SR X2 module).
z On B24X, use 69Y0389 (10GBASE-SR
41Y8522
46C7191
2
2
SFP+).
z Connect over multi-mode fiber. (Note: The
X2 module has a SC connector, whereas
the SFP+ has a LC connector.)
BNT Virtual Fabric 10Gb Ethernet Switch
Module
z On BNT ESM, use 44W4408
(10GBASE-SR SFP+).
z On B24X, use 69Y0389 (10GBASE-SR
SFP+).
z Connect over multi-mode fiber.
IBM System x server
z On System x server with Brocade 10Gb
CNA [42C1820], QLogic 10Gb CNA
[42C1800], or Emulex Virtual Fabric
Adapter [49Y4250], connect using a single
Direct Attach cable (TwinAx), available in 1,
3, or 5 meters. (See Table 4.)
Varies
-
z On System x server with NetXtreme II 10
GigE Express Fiber SR Adapter
(42C1790), use 69Y0389 (10GBASE-SR
SFP+) on B24X and connect over
multi-mode fiber.
z See Table 6 for server adapter details.
Other servers
z If 10GBASE-SR, connect to B24X using
69Y0389 (10GBASE-SR SFP+) over
multi-mode fiber.
Varies
-
z If 1 GbE, most 1 GbE NICs are RJ-45.
Connect to one of the B24X’s four RJ-45
ports over CAT5 cable.
IBM Ethernet Switch B24X
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Interoperating in existing network environments
The IBM Ethernet Switch B24X interoperates seamlessly in existing network environments utilizing
standards-based protocols. IBM Ethernet Switch B24X leverages the proven IronWare Operating System
with an industry-standard CLI so network administrators can utilize their existing skill sets.
Figure 8 shows an example of the B24X used as an access and aggregation switch.
Figure 8. IBM Ethernet Switch B24X connecting to the network infrastructure
IBM Ethernet Switch B24X
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 10 outlines the components used in Figure 8.
Table 10. The components used in Figure 8
Diagram
Reference
Part number/
machine type
Description
IBM Ethernet Switch B24X
Quantity
1
0563-012
IBM Ethernet Switch B16M
z On B16M, use FC1711 (4-port 10 GbE XFP
module) and FC2110 (10GBASE-SR XFP).
z On B24X, use 69Y0389 (10GBASE-SR SFP+).
z Connect over multi-mode fiber.
4003-M16
1
1
Cisco Catalyst 6509-E
z On 6509, use 8-port 10 GbE Fiber module with
X2-10GB-SR (10GBASE-SR X2 module).
z Connect over multi-mode fiber. (Note: The X2
module has a SC connector, whereas the SFP+
has a LC connector.)
N/A
IBM Ethernet Switch B48Y (Data Center model)
z On B48Y, use 81Y1455 (4-port 10 GbE SFP+
module).
z Use a single Direct Attach cable (TwinAx) to
connect to B24X, available in 1, 3, or 5 meters if
length permits.
z Otherwise, on B24X use 69Y0389
(10GBASE-SR SFP+) and connect over
multi-mode fiber.
0563-HCF
1
1
Cisco Catalyst Nexus 4948-10GE
z On the Catalyst use the 10GBASE-SR X2
module.
N/A
z On B24X, use 69Y0389 (10GBASE-SR SFP+).
z Connect over multi-mode fiber
Power supplies and fans
The IBM Ethernet Switch B24X comes with one 300 W AC power supply and supports a second power
supply for 1+1 redundancy. The power supplies are hot-swappable, auto-sensing, auto-switching, and
load sharing, with a universal input (90 VAC to 264 VAC). The power supply has an IEC-C14 inlet that
connects to a C13 power connector. Power cords are not included with the switch and must be provided
separately.
The IBM Ethernet Switch B24X also comes with a single fan tray consisting of three variable-speed fans.
If one fan within the fan tray fails it does not affect the operation of the other fans in the unit. The fan tray
is hot-swappable, increasing device availability and serviceability.
Figure 9. IBM Ethernet Switch B24X rear view (fans and power supply)
IBM Ethernet Switch B24X
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The airflow of the switch is primarily port/side (front) to non-port (back) side. Air is drawn into the system
from vents on the front and front sides of the switch and expelled out the rear. The cooling characteristics
of the system allow it to be deployed in server racks featuring hot-cold aisle containment without the need
of special baffling.
Figure 10. IBM Ethernet Switch B24X airflow
Installation
The IBM Ethernet Switch B24X comes with two rack-mount brackets affixed to each side for installation
into an EIA-310D compliant rack. Screws for mounting the B24X to the rack are not included with the
switch. Allow at least 3 inches of space at the front, back, and sides of the device for proper cabling and
cooling
Figure 11. IBM Ethernet Switch B24X rack mount kit
Network cabling requirements
The network cables required for the IBM Ethernet Switch B24X are:
z
10GBASE-SR SFP+ transceiver [69Y0389]
z
840 to 860 nm wavelength using multi-mode fiber cable, LC duplex connector. Operating
distance supported depends on the multi-mode fiber cable used. See Table 11.
z
z
1000BASE-T (built-in 10/100/1000 MbE RJ-45 ports) and 1000BASE-TX SFP transceiver: up to 100
m over UTP Category 5e or higher cabling, RJ-45 connector.
DB9 male serial console port: DB9 female-to-DB9 female straight-through serial console cable that
comes with the switch.
IBM Ethernet Switch B24X
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 11. Multi-mode fiber cable distances supported
Multi-mode fiber cable
62.5 ìm (160 MHz*km)
62.5 ìm (200 MHz*km)
50 ìm (400 MHz*km)
50 ìm (500 MHz*km)
50 ìm (2000 MHz*km)
Distance
Loss
26 m
33 m
66 m
82 m
300 m
1.6 dBm
1.6 dBm
1.7 dBm
1.8 dBm
2.6 dBm
Related links
For more information, see the following resources:
z
z
z
IBM System x network options support site for model-type 0563 – code download and documentation
0563
IBM Redbooks publication IBM b-type Data Center Networking: Design and Best Practices
Introduction, SG24-7786
IBM Redbooks publication IBM b-type Data Center Networking: Product Introduction and Initial Setup,
SG24-7785
·
IBM Ethernet Switch B48Y product page
z
IBM Ethernet Switch B24X product page
z
z
z
z
IBM Configuration and Options Guide
IBM Smarter Networks
IBM b-type Ethernet switches and routers
IBM Ethernet Switch B24X
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local
IBM representative for information on the products and services currently available in your area. Any reference to an
IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may
be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property
right may be used instead. However, it is the user's responsibility to evaluate and verify the operation of any non-IBM
product, program, or service. IBM may have patents or pending patent applications covering subject matter described
in this document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
IBM Director of Licensing, IBM Corporation, North Castle Drive, Armonk, NY 10504-1785 U.S.A.
The following paragraph does not apply to the United Kingdom or any other country where such provisions
are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or
typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in
new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
Any references in this information to non-IBM Web sites are provided for convenience only and do not in any manner
serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this
IBM product and use of those Web sites is at your own risk.IBM may use or distribute any of the information you
supply in any way it believes appropriate without incurring any obligation to you. Information concerning non-IBM
products was obtained from the suppliers of those products, their published announcements or other publicly
available sources. IBM has not tested those products and cannot confirm the accuracy of performance, compatibility
or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products should be
addressed to the suppliers of those products. This information contains examples of data and reports used in daily
business operations. To illustrate them as completely as possible, the examples include the names of individuals,
companies, brands, and products. All of these names are fictitious and any similarity to the names and addresses
used by an actual business enterprise is entirely coincidental.
Any performance data contained herein was determined in a controlled environment. Therefore, the results obtained
in other operating environments may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements will be the same on generally
available systems. Furthermore, some measurement may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their specific environment.
COPYRIGHT LICENSE:
This information contains sample application programs in source language, which illustrate programming techniques
on various operating platforms. You may copy, modify, and distribute these sample programs in any form without
payment to IBM, for the purposes of developing, using, marketing or distributing application programs conforming to
the application programming interface for the operating platform for which the sample programs are written. These
examples have not been thoroughly tested under all conditions. IBM, therefore, cannot guarantee or imply reliability,
serviceability, or function of these programs.
© Copyright International Business Machines Corporation 2010. All rights reserved.
Note to U.S. Government Users Restricted Rights -- Use, duplication or disclosure restricted by
GSA ADP Schedule Contract with IBM Corp.
IBM Ethernet Switch B24X
21
Download from Www.Somanuals.com. All Manuals Search And Download.
This document was created or updated on November 9, 2010.
Send us your comments in one of the following ways:
z
Use the online Contact us review form found at:
ibm.com/redbooks
z
z
Send your comments in an e-mail to:
Mail your comments to:
IBM Corporation, International Technical Support Organization
Dept. HYTD Mail Station P099
2455 South Road
Poughkeepsie, NY 12601-5400 U.S.A.
Trademarks
IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business
Machines Corporation in the United States, other countries, or both. These and other IBM trademarked
terms are marked on their first occurrence in this information with the appropriate symbol (® or ™),
indicating US registered or common law trademarks owned by IBM at the time this information was
published. Such trademarks may also be registered or common law trademarks in other countries. A
The following terms are trademarks of the International Business Machines Corporation in the United
States, other countries, or both:
BladeCenter®
IBM®
MVS™
Redbooks®
Redpaper™
Redbooks (logo)®
System i®
System p®
System Storage®
System x®
The following terms are trademarks of other companies:
Microsoft, and the Windows logo are trademarks of Microsoft Corporation in the United States, other
countries, or both.
UNIX is a registered trademark of The Open Group in the United States and other countries.
Linux is a trademark of Linus Torvalds in the United States, other countries, or both.
Other company, product, or service names may be trademarks or service marks of others.
IBM Ethernet Switch B24X
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|