T84H_setup0926_final.fm Page 2 Thursday, October 5, 2000 8:45 AM
Setup
Hardware Requirements
This monitor requires a computer with a suitable on-board sub-system or
Video Adapter card that can support SXGA 1280 x 1024, XGA 1024 x 768,
SVGA 800 x 600, or VGA 640 x 480 at 60 Hz. For optimal performance, the
recommended video setting is 1280 x 1024 at 60 Hz. The monitor has the
capability to receive input either from an analog graphics adapter or a Digital
Visual Interface DVI-D graphics adapter. If your PC is not already equipped
with a suitable graphics adapter, you must install one. If needed, contact
your dealer to purchase a compatible graphics adapter.
Handling Instructions
Do not support the monitor
within the screen area. The
Liquid Crystal Display is
glass and can be damaged
by rough handling or
1. Lift the monitor by placing your hands where indicated below.
excessive pressure.
2. Before using your monitor for the first time, remove the clear protective
film from the front of the screen.
Workplace Preparation
This section gives advice
Height
on what you should
consider before you set up your
monitor.
The monitor should be positioned so that the top of the screen is slightly
below your eye level when you sit at your workstation.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 4 Thursday, October 5, 2000 8:45 AM
Use a light touch on the keyboard, keeping your hands and fingers relaxed.
Allow a space in front of the keyboard to rest your wrists when not typing.
Consider using a wristpad.
Eyesight
Working with monitors, in common with any prolonged close work, can be
visually demanding. Look away from the screen periodically and have your
eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You may have
to adjust this as the lighting changes during the day. Many application
programs let you select color combinations which can help you to view in
comfort. See the User controls section on page 15 for more information.
Caring for your Monitor
Be sure to turn off the power before you perform any maintenance on the
monitor. Clean your monitor as follows:
•
•
Gently wipe the device covers and the screen with a soft cloth.
Remove finger marks and grease with a damp cloth and mild detergent;
do not use solvents or abrasives
•
Never use flammable cleaning material to clean your IBM monitor or any
other electrical apparatus.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 5 Thursday, October 5, 2000 8:45 AM
Connecting your Monitor for Analog
Be sure to read the ‘Safety
Information’ at the front of
this User Guide before
1. Turn off your PC and all attached devices.
2. Connect the signal cable to the video port on the back of your computer.
This port might be directly attached to your computer (figure A), or it
might be part of a video adapter card (figure B). The video port on your
computer or video adapter card may be colored blue to match the blue
connector on your monitor’s video cable.
carrying out this procedure.
The AC adapter and signal
cable are connected to your
monitor. If you wish to change
these or to fit a different stand, see
Further Help on page 26.
3. Connect the power cord to the power adapter first, then insert the plug
into a properly grounded electrical outlet.
Connecting your Monitor for Digital
1. Turn off your PC and all attached devices.
2. Remove rear covers a, b and c per instructions 2, 3 and 4 on page 26.
3. Locate DVI cable. It is shipped in a separate plastic bag in the shipping
carton.
Connecting DVI Cable
DVI
Cable
5
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 6 Thursday, October 5, 2000 8:45 AM
4. Connect the DVI connector at the end of the signal cable to the DVI port
located on the back of the Monitor. See above picture.
5. Connect the DVI connector at the other end of the signal cable to the
DVI port located on the back of the graphics adapter. See picture below.
graphics adapter
DVI
Signal Cable
6. Replace the rear covers.
7. Connect the power cord to the power adapter first, then insert the plug
into a properly grounded electrical outlet.
8. Switch on the power source and your computer. To turn on the monitor,
push and release the power switch . To switch it off, push and release
the power switch again.
Switching on your Monitor
1. Switch on the power source and your computer.
2. Switch on your monitor by pushing and releasing the power switch
marked
.
To switch off your monitor, push and release the power switch again.
3. Turn on the monitor and then the computer.
4. Run AUTO SETUP by following the instructions in the Configuring your
Monitor section on page 7.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 7 Thursday, October 5, 2000 8:45 AM
Configuring your Monitor
Setup Diskette for Windows95 or Windows 98
This section must be
completed before
continuing with the
Windows 95 or Windows 98
Auto Setup on Page 10.
To use the Plug and Play feature in Windows 95 or Windows 98, files should
be loaded from the IBM Flat Panel Monitor Installation diskette:
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow the system to boot
into Windows 95 or Windows 98.
Your computer’s Plug and Play code may warn you that your system
hardware has changed. This probably means that it has detected your
new monitor for the first time.
4.
5.
Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,
CONTROL PANEL and then double clicking on the DISPLAY icon.
Select the SETTINGS tab.
On LCD monitors, unlike
CRTs, a faster refresh
rate does not improve display
quality. IBM recommends
using either 1280 x 1024 at a
refresh rate of 60Hz.
• In case of Windows 95:
6. -1. Select the Change Display Type button.
2. Select the Change Monitor Type button.
• In case of Windows 98:
6. -1. Select the ADVANCED BUTTON.
2. Select the MONITOR tab.
3. Open the UPGRADE DEVICE WIZARD windows by clicking on
Change button and then select the NEXT button.
If the UPGRADE DEVICE WIZARD is open go step 6-3. if not
continue to step 4.
4. Select the “Display a list of the known drivers for this device so that
I can choose a specific driver” and then select the NEXT button.
7. Insert the Setup diskette into drive A: and select the HAVE DISK button.
8. Select OK.
9. Choose IBM T84H monitor and select OK. The files will be copied from
the diskette to your hard drive.
10. Close all open windows and remove the diskette.
11. Reboot the system.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 8 Thursday, October 5, 2000 8:45 AM
Setup Diskette for Windows 2000
This section must be
completed before
continuing with the
Windows 2000 confguring
for your monitor on page 10.
To use the Plug and Play feature in Windows 2000, files should be loaded
from the IBM Flat Panel Monitor Installation diskette.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow the system to boot
into Windows 2000.
4.
Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,
CONTROL PANEL and then double clicking on the DISPLAY icon.
5.
Select the SETTINGS tab.
6. Select the ADVANCED button.
7. Select the MONITOR tab.
On LCD monitors, unlike
CRTs, a faster refresh rate
does not improve display
quality. IBM recommends using
either 1280 x 1024 at a refresh
rate of 60Hz.
8. Select the PROPERTIES button.
9. Select the Driver tab.
10. Open theUpgrade Device Driver Wizard window by clicking on UPDATE
DRIVER and then select the NEXT button.
11. select the “Display a list of the known dirvers for this device so that lcan
choose a specifc driver” and then sefect the NEXT button.
12. Inset the Setup diskette into drive A: and select the HAVE DISK button.
13. select OK.
14. Choose IBM T84H monitor and select OK. The files will be copied from
the diskette to your hard drive.
15. Close all open windows and remove the diskette.
16. Reboot the system.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 9 Thursday, October 5, 2000 8:45 AM
Auto Setup(Analog Only)
Auto Setup
Before carrying out this
section, it is very
important that The
When you first use your monitor you must perform Auto Setup. This
procedure sets up your monitor to process the video signals from your
computer without image discoloration or smearing. After you perform Auto
Setup, the settings are stored and used each time you turn on the monitor.
Setup Diskette for Windows
95 or Windows 98 has been
run. (see page 6)
In order to optimise the displayed image a set-up utility is provided on the IBM
Monitor Installation Diskette. Operation of the utility is dependent on the
operating system on your PC. For correct operation locate the operating
system on your PC from the table below and follow the appropriate
instructions. You may choose to run AUTO SETUP for each operating system
that you use. This means that if you sometimes use your monitor while
running any version of Windows and sometimes also use it from within DOS
(not a DOS window), you must run AUTO SETUP for both Windows and DOS.
You may run versions of AUTO SETUP in any order.
The Setup Utility
included on the setup
diskette is for displaying do
patterns. They do not replace
or modify the display dirver.
The Auto Setup
instructions require the
monitor to be warmed up for
15 minutes. This is not
required for normal operation.
Operating System
DOS
Corresponding Auto Setup procedure
Auto Setup for DOS on page 9
Windows 3.1
Windows 95
Windows 98
Window 2000
Window NT
Auto Setup for Windows 3.1, Windows 95,
Windows 98, Windows 2000 or Windows
NT on page 10
If your PC does not run
with the setup diskettes
Before you begin AUTO SETUP for your PC:
shipped with the monitor, refer
to Manual Setup on page 12
1. Make a backup copy of the setup diskettes supplied with the monitor.
2. Make sure the PC’s video mode is set in the range of the supported
screen resolution shown in the table on page 18.
The AUTO SETUP process
only applies to the current
screen mode. When a new
mode is selected, repeat this
section to reset the monitor
You should perform AUTO SETUP for each screen mode you use.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 10 Thursday, October 5, 2000 8:45 AM
Auto Setup for DOS
If the monitor is in standby
1. Turn on the monitor first; then the PC.
mode (STANDBY ON), it
may automatically turn off while
you are waiting for it to warm up.
If this happens, switch off the
monitor and switch it on again
after a few seconds.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
If you are using PC-DOS/
V, change to U.S. mode by
typing ‘CHEV US’ and pressing
ENTER at the command
prompt.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Diskette
into the diskette drive.
You must use DOS when
you run DOS Auto Setup.
4. Display the command prompt screen of the DOS full-screen display.
5. At the command prompt, type ‘A:’ and press ENTER.
6. Type ‘TESTPATD’ and press ENTER.
7. Select from the screen the number for the color or text mode you want to
setup.
8. Select from the screen the number for the video mode you want to
setup.
You may repeat this process for as many of the color and video modes
as you need.
The size and diversity of
the dot pattern varies with
the screen resolution.
9. When the dot pattern appears, press the OSD Enter button
bottom of the monitor to display the initial OSD menu.
at the
If the screen flickers,
10. Use an Arrow button (
then press the OSD Enter
or
) to select the IMAGE LOCK icon
button to access the function.
repeat the setup several
times until the flicker is
minimised, or adjust it manually
by following Manual Setup on
page 14.
11. Using an Arrow button (
or
), select AUTOMATIC and press the
OSD Enter button
. This activates the AUTO SETUP procedure, which
will optimize the display settings with the provided dot-patterns.
The screen will blink off several times and you may notice small
changes to the test pattern.
12. When finished, the OSD main menu returns. Press the Exit button
to exit from the OSD.
13. Press the ESCAPE key to exit the test pattern program.
14. Type ‘Exit’ at the command prompt to return to Windows.
If you use other operating systems, perform the appropriate AUTO SETUP for
those systems, also: see
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT or
Windows 2000 on page 10.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 11 Thursday, October 5, 2000 8:45 AM
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT
or Windows 2000
If the monitor is in standby
mode (STANDBY ON), it
1. Turn on the monitor first; then the PC.
may automatically turn off while
you are waiting for it to warm up.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the
screen.
4. Insert the diskette labelled ‘IBM Flat Panel Monitor Installation Disk’ into
the diskette drive.
The size and diversity of
the dot pattern varies with
the screen resolution.
5. Check the operating system installed on your PC and follow the
instructions from the table below.
Operating
System
Step1
Step2
Step3
Step4
Windows 3.1
Open
PROGRAM
MANGER
Select
FILE
Select
RUN
Windows NT 3.5
Type
‘A:\TESTPAT’
and press
ENTER
Windows 95
Select
START
Windows 98
Select RUN
Windows NT 4.0
6. When the test pattern appears, press the OSD Enter button
bottom of the monitor to display the initial OSD menu.
at the
Position the mouse pointer
at the bottom center of the
screen. This allows AUTO
SETUP to run properly
7. Use an Arrow button (
and press the OSD Enter button
8. Using an Arrow button ( or
OSD Enter button . This activates the AUTO SETUP procedure, which
or
) to select the IMAGE LOCK icon
to access the function.
), select AUTOMATIC and press the
will optimize the display settings with the provided test pattern.
The screen will dim, blink on and off several times, and you may notice
small changes to the test pattern.
To abort the AUTO SETUP function, press the ESC key.
9. When finished, the OSD main menu returns. Press the Exit button
once to exit from the OSD.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 12 Thursday, October 5, 2000 8:45 AM
10. Press the ESC key to return to Windows.
You have completed the monitor setup for Windows. If you use other operat-
ing systems, perform the appropriate AUTO SETUP for those systems, also: see
Auto Setup for DOS on page 10.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 13 Thursday, October 5, 2000 8:45 AM
Manual Setup
Normally, you can complete the setup procedure using AUTO SETUP, however,
if your screen image is still distorted after you perform AUTO SETUP or the
setup diskette does not run on your system, perform MANUAL SETUP.
If the monitor is in standby
mode (STANDBY ON), it
might automatically turn off
while you are waiting for it to
warm up.
1. Have your monitor turned on for about 15 minutes, until the monitor
warms up.
2. Display the image you most frequently use on the screen.
3. Press the OSD Enter button
the initial OSD menu.
at the bottom of the monitor to display
4. Use an Arrow button (
and press the OSD Enter button
5. Using an Arrow button ( or
press once to select COARSE. Left and right arrow adjustment
or
) to select the IMAGE LOCK icon
to access the function.
), select MANUAL, press
and then
indicators become illuminated (see page 18).
6. Use the Arrow buttons to manually adjust to correct (as much as
possible) for noise in the video signal then press
changes.
to save the
7. Use an Arrow button to select FINE and press the
button.
8. Use the Arrow buttons again to tune the image to your liking.
9. When finished, press the Exit button
OSD.
four times to exit from the
You have completed the monitor setup.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 14 Thursday, October 5, 2000 8:45 AM
Adjusting Your LCD Monitor
User controls
User control features
Icon
Control
Exit
Description
OSD inactive: Switches the video input source
OSD active: Exits from menus and sub-menus
Exits the OSD
Displays the OSD main menu
Moves the cursor to highlight icons and other
options
Left Arrow
Displays the OSD main menu
Moves the cursor to highlight icons and other
options
Right Arrow
Displays the OSD main menu
Enters menus and sub-menus and selects the
highlighted option
OSD Enter
Power Switch
Switches the monitor on and off
Operation
The image is already
optimized for many display
modes, however the user
controls can be used to adjust
the image to your liking.
•
•
Press any of the OSD control buttons to display the main OSD menu.
Use the Arrow buttons to move among the icons. Select an icon and press
OSD Enter to access that function. If there is a sub-menu, you can move
between options using the Arrow buttons, then press OSD Enter to select
that function. Use the Arrow buttons to make adjustments.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 15 Thursday, October 5, 2000 8:45 AM
The settings are saved
•
Press the Exit button to move backwards through the sub-menus and exit
from the OSD.
after adjustment and when
exiting the OSD and will be
effective thereafter.
Note: After making adjustments, the Power indicator LED will briefly
turn amber to indicate that the new value has been saved.
OSD Lock / Unlock
This feature allows you to secure the current control settings, while allowing
the user to adjust Brightness and Contrast, so that they cannot be
inadvertently changed. You can unlock the OSD controls at any time by using
the same procedure.
Push and hold the OSD Enter button for 10 seconds to Lock or to Unlock.
When locked, a “LOCKED” message will be displayed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 16 Thursday, October 5, 2000 8:45 AM
On-screen display (OSD) controls
The settings adjustable with the user controls are viewed through the On-
Screen Display (OSD). Press any of the OSD buttons to activate the OSD.
The LCD monitor needs
time to become thermally
Initial appearance of OSD
stable the first time you turn it on
each day. Thus, to achieve more
accurate adjustments for
parameters, allow the LCD
monitor to warm up (be On) for
at least 15 minutes before
making any screen adjustments.
OSD functions
Sub-
menu(s)
Controls and
Adjustments(Analog)
Controls and
Adjustments(Digital)
OSD Icon
BRIGHTNESS
CONTRAST
Description
Adjusts brightness
Adjusts contrast
Same as Analog
Controls Locked
Automatic adjusts the
monitor.
The image lock function is used to
adjust the level of noise in the
video signal which causes
AUTOMATIC
IMAGE LOCK
horizontal lines or areas on the
screen where the image appears
to be unstable and jitters or
shimmers. This can be done
automatically or manually.
Controls Locked
16
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 17 Thursday, October 5, 2000 8:45 AM
Sub-
menu(s)
Controls and
Adjustments(Analog)
Controls and
Adjustments(Digital)
OSD Icon
Description
Use the Arrow buttons to
adjust away the
MANUAL -
interference. If
•
•
Fine
Coarse
IMAGE LOCK
(continued)
satisfactory results are
not obtained using the
Fine adjustment, use the
Coarse adjustment and
then use Fine again.
This function may
Controls Locked
change the width of the
display image. Use the
H-Position function to
center the display image
on the screen.
Select the preset Color mode you
find most comfortable and then
fine tune the colors using the User
submenu, if necessary.
PRESET
USER
1 - (Cool White)
2 - (Normal White)
3 - (Warm White)
COLOR
Controls Locked
•
•
•
Red
Increases or decreases
redness
Increases or decreases
greenness
Increases or decreases
blueness
Green
Blue
Resets the Brightness, Contrast,
Image Lock Fine and Coarse,
Color, H-Position, V-Position, and
Display Size settings.
NO - Does not make the
adjustment
YES - Resets the
settings
Controls Locked
Controls Locked
Controls Locked
RESET
Moves the screen left and right.
Moves the screen down and up.
H-POSITION
V-POSITION
EXPANDED
NORMAL
1 - Image enlarged to fill
the entire screen.
2 - Image enlarged to fill
the width of the screen
only.
If your computer or video board
supplies a signal rate and
addressability lower than 1280 x
1024, this LCD monitor provides a
scaling processor that can
expand the addressability up to
1280 x 1024.
DISPLAY
SIZE
Same as Analog
Image at normal size.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 18 Thursday, October 5, 2000 8:45 AM
Sub-
menu(s)
Controls and
Adjustments(Analog)
Controls and
Adjustments(Digital)
OSD Icon
Description
Select this icon to optimize the
display for the type of software
you are using.
Scaling smooths an image which
may help the eye to see more
detail. Filtering sharpens text by
adding a fine, contrasting line
around each character so that it is
easier to recognize.
SCALING
FILTER
ON - Turns Scaling on.
OFF - Turns Scaling off.
IMAGE
EFFECT
ON - Turns Filtering on.
OFF - Turns Filtering off.
Same as Analog
The language chosen affects only
the language of the OSD. It has
no effect on any software running
on the computer.
Select one of the five
languages to use for the
OSD.
Same as Analog
Same as Analog
LANGUAGE
Changes the position of the OSD
on the screen.
H-POSITION
V-POSITION
OSD MENU
POSITION
This monitor can accept video
signals through two different
connectors.
1 - selects D-SUB
(Analog)
2 - selects DVI-Analog
Most desktop computers use a D-
SUB connector. Select DVI-D
among OSD controls when you
use DVI connector.
Same as Analog
INPUT
SELECTION
3 - selects DVI-Digital
Shows information about the
addressability and the horizontal
and vertical frequencies available.
The current setting for the images
received from the computer or
video board is displayed along the
bottom of both submenus.
USER
MODES
Lists all modes which
you have defined by
making changes using
the OSD controls
INFORMATION
Same as Analog
PRESET
MODES
Lists all modes that have
been defined during
manufacture
18
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 19 Thursday, October 5, 2000 8:45 AM
Further Information
Display modes
The display mode the monitor uses is controlled by the computer. Therefore,
you should refer to your computer documentation for details on how to
change display modes.
The image size, position and shape may change when the display mode
changes. This is normal and the image can be readjusted using AUTO SETUP
and the monitor controls.
Unlike CRT monitors, which require a high refresh rate to minimize flicker,
TFT technology is inherently flicker-free. If possible, configure your computer
for 1280 × 1024 addressability at 60Hz vertical refresh rate.
For the display modes listed below, the screen image has been optimized
during manufacture.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 20 Thursday, October 5, 2000 8:45 AM
Factory Set Display Modes
Horizontal
Frequency
Addressability
Refresh Rate
Analog
Digital
For image problems, you
may want to run AUTO
640 × 350
640 × 480
70 Hz
75 Hz
72 Hz
66 Hz
60 Hz
70 Hz
56 Hz
60 Hz
72 Hz
75 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
70 Hz
75 Hz
76 Hz
75 Hz
75 Hz
60 Hz
31.5 kHz
37.5 kHz
37.8 kHz
35.0 kHz
31.5 kHz
31.4 kHz
35.1 kHz
37.8 kHz
48.0 kHz
46.8 kHz
49.7 kHz
48.4 kHz
56.5 kHz
60.0 kHz
64.0 kHz
74.4 kHz
80.0 kHz
81.1 kHz
67.5 kHz
68.7 kHz
61.8 kHz
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
Setup again before consulting
to this section. In most cases,
AUTO SETUP can fix the
problems. See Auto Setup on
page 8 for details.
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
1024 x 768
1280 x 1024†
1280 x 1024
1280 x 1024
1280 x 1024
1152 x 864
1152 x 870
1152 x 900
† Recommended
X
X
X
X
O
‘Note: VESA timings are as detailed in the VESA “Display Monitor Timing
Specification”. Version 1.0, Revision 0.8, dated 09/17/98.’
20
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 21 Thursday, October 5, 2000 8:45 AM
Power Management
If your computer has
previously been used
To benefit from power management, the monitor must be used in conjunction
with a computer that implements the Video Electronics Standards Association
(VESA) Display Power Management Signalling (DPMS) Standard.
with a CRT monitor and is
currently configured to a
display mode outside the
range that the Flat Panel
monitor can display, you
may need to re-attach the
CRT monitor temporarily
until you have re-configured
the computer, preferably to
1280 x 1024 at 60Hz.
The power management feature is invoked when the computer recognizes
that you have not used your mouse or keyboard for a user-definable period.
There are several states as described in the table below.
As an ENERGY STAR® Partner, IBM has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
IBM recommends that you switch off your monitor at the end of each working
day, or whenever you expect to leave it unused for long periods during the
day.
Power
Indicator
Restoring
Operation
State
Screen
Normal
Blank
Compliance
On
Steady green
Steady amber
®
DPMS
Standby
Press a key or
move the mouse.
ENERGY STAR
and NUTEK
Flashing
amber
(0.5 sec.
interval)
®
DPMS
Suspend
Press a key or
move the mouse. ‡
ENERGY STAR
and NUTEK
Blank
Blank
Flashing
amber
(1 sec.
interval)
®
Press a key or
move the mouse. ‡
ENERGY STAR
and NUTEK
DPMS Off
‡ There may be a slight delay before the picture reappears.
Product Disposal
The fluorescent lamp in the liquid crystal display contains mercury. Dispose of
it as required by local ordinances and regulations.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 22 Thursday, October 5, 2000 8:45 AM
Troubleshooting
If you have a problem setting up or using your monitor, you may be able to
solve it yourself. Before calling your retailer or IBM, try the suggested actions
that are appropriate to your problem.
Possible
Cause
Problem
Suggested Action
Reference
w
Remove the other
graphics adapter plugged
into one of the expansion
slot.
Computer
doesn’t boot
after the
graphics
adapter is
installed
Connecting
your Monitor
for Analog
section on
There is
another
graphics
adapter in the
computer
w
If the card is built-in to
the motherboard, check
your system manual for
instructions on how to
disable the built-in adapter.
page 5
The screen
image is
garbled or
unusable
(rolling screen
images,
overlapping
screen images
or a blank
screen)
The display
driver is trying
to use a
setting your
monitor
Connecting
your Monitor
for Analog
section on
w
Select the correct
monitor again.
doesn’t
support
page 5
22
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 23 Thursday, October 5, 2000 8:45 AM
Possible
Cause
Problem
Suggested Action
Reference
w
Ensure that the
electrical outlet and the
monitor are both switched
on.
w
Check that the power
cord is firmly plugged into
the electrical outlet and the
power supply unit.
Connecting
your Monitor
for Analog
section on
Screen is blank
and power
indicator is off
No power to
monitor
w
If the power cord plug
has a removable fuse,
replace it.
page 5
w
Try another power
cord.
w
Try another electrical
outlet.
User
Screen is blank
and power
indicator is
Brightness
and Contrast
may be too
low
w
Adjust brightness and
contrast.
controls
section on
page 15
steady green
w
Press any key on the
keyboard or move the
mouse to restore
operation.
Power
Screen is blank
and power
indicator is
Themonitoris
in the Power
Management
Standby state
Management
section on
page 19
w
Check the Power
steady amber
Management software on
your computer
w
Check that the signal
cable is firmly connected to
the computer.
Connecting
your Monitor
for Analog
section on
Themonitoris
not receiving
a video signal
w
Check that no pins are
Screen is blank
and power
indicator is
Flashing green
every 0.5
bent in the signal cable
connector.
page 5
Display mode
of the
computer is
outside the
range of the
monitor
Further
second
w
Reconfigure the
computer to use a
Information
section on
page 20
supported display mode.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 24 Thursday, October 5, 2000 8:45 AM
Possible
Cause
Problem
Suggested Action
Reference
w
Press any key on the
The monitor is keyboard or move the
Screen is blank
and power
indicator is
flashing amber
every 0.5 or 1
second
Power
in the Power
Management
Suspend or
Off state
mouse to restore
operation.
Management
section on
page 19
w
Check the Power
Management software on
your computer.
User
w
Select IMAGE LOCK
There are
noises in the
video signal
Image appears
to be smeared
controls
section on
page 15
menu in the OSD. Then
select MANUAL to adjust
FINE/COARSE settings.
User
Image appears
to be
discolored
The Color
setting may
be incorrect
w
Adjust the Color
settings.
controls
section on
page 15
w
The LCD contains over 3,900,000 thin-
A few dots are
missing,
discolored, or
inappropriately
lighted.
film transistors (TFTs). A small number of
missing, discolored, or lighted dots may be
present on the screen, which is an intrinsic
characteristic of the TFT LCD technology
and is not an LCD defect.
Power consumption
figures are for the monitor
and the power supply
combined.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 25 Thursday, October 5, 2000 8:45 AM
Further Help
If you are unable to correct the problem yourself, you may seek further help
as follows:
Call the IBM HelpCenter(R).
In the US call 1-800-772-2227
In Canada (Toronto Only) call 416-383-3344
In Canada (all others) call 1-800-565-3344
In other countries contact your dealer, retailer, or other IBM authorized
Servicer.
If possible, stay by your
computer. Your Technical
Support Representative may
wish to go through the problem
with you during the call.
Before calling, please have available as much of the following information as
possible:
1. Model and serial number from the label on your monitor.
2. Purchase receipt.
3. Description of problem.
4. Computer type and model.
5. System configuration (hardware fitted, etc.).
6. System BIOS version number.
7. Operating System and version number.
8. Display driver version number.
9. Video Adapter Type.
More help, late-breaking
news and details of the
Removing the stand and cables
Alternative stands for your IBM Flat Panel Monitor may be available from
specialist suppliers.
latest accessories for these
products may be found on the
worldwide web at:
This product is equipped with mounting facilities that conform to the VESA
Flat Panel Monitor Physical Mounting Interface Standard (FPMPMI).
accessories
This product is shipped with the signal cable and the power cord attached to
the monitor. If you want to use other cables for reasons such as having the
monitor wall-mounted, follow the instructions below:
Information about the Video
Electronics Standards
Association can be found on the
worldwide web at:
1. Disconnect the power cord from the wall outlet.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 26 Thursday, October 5, 2000 8:45 AM
2. Carefully insert the head of a flathead (–) screwdriver into the slot visible
along either side of the cable cover (a) and pry it off.
a
b
c
3. Squeeze the sides of the hinge cover (b) and pull it off.
4. Gently lift the stand cover (c) along the top and then slide it backwards
and off the stand.
5. Remove the signal cable and the power cord from the monitor by
disconnecting the corresponding adapters. Carefully cut the plastic tie to
free the power cord and remove the screw holding the power cord
clamp.
6. Lay the monitor facedown on a cushion and remove the six screws
holding the hinge mechanism on the monitor. Lift off the hinge and base
assembly.
7. If you are installing an arm or wall-mounting device, follow the directions
included with the device. If you are just changing your cables, continue
with Step 8.
8. Connect the signal cable and the power cord, then refit the power cord
clamp in its original screwpost.
9. Slide the stand cover back on the stand.
10. Put the hinge cover back on, making sure that the straight side is at the
top.
11. Insert the three tabs at the top of the cable cover into the slots in the
back of the monitor and push the cover into place.
To obtain the correct cables and/or to get further instructions on installing
them, call the IBM HELPCENTER at the above numbers or contact your
dealer, retailer, or other IBM authorized Servicer.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 27 Thursday, October 5, 2000 8:45 AM
Specifications
This color monitor (Type-model 6658-Hxx) uses a 18.1-inch TFT LCD
Dimensions
Width:
Depth:
Height:
462 mm (18 in.)
233 mm (9 in.)
458 mm (18 in.)
Weight
Unpackaged:
Packaged:
9.0 Kg (19.8 lb)
12.0 Kg (30.5 lb)
Tilt / Swivel
Image
Tilt:
Swivel:
– 4° / + 41°
– 230° / + 90°
Viewable Image Size:
Maximum Height:
Maximum Width:
Pixel Pitch:
459.7 mm (18.1 in.)
287 mm (11 in.)
359 mm (14 in.)
0.281 mm (.011 in.) (H)
× 0.281 mm (.011 in.) (V)
Power Input
Supply Voltage:
Max Supply Current:
90 - 260 Vac, 60/50 ± 3 Hz
1.5 A at 120 Vac
Power Consumption
Normal Operation:
DPMS Stand-by:
DPMS Suspend:
DPMS off:
< 48 W
< 3 W for Analog, < 4 W for Digital
< 3 W for Analog, < 4 W for Digital
< 3 W for Analog, < 4 W for Digital
Video Input(Analog)
Video Input(Digital)
Input Signal:
Analog Direct Drive, 75 ohm 0.7 V
1280 pixels (max)
1024 lines (max)
Horiz. Addressability:
Vert. Addressability:
Clock Frequency:
135 MHz
Interface:
DVI
Input Signal:
VESA TMDS (Panel Link TM)
1280 pixels (max)
1024 lines (max)
106 MHz
Horiz. Addressability:
Vert. Addressability:
Clock Frequency:
Communications
VESA DDC:
2 B
Supported Display
Modes
VESA Standard modes between
Horiz. Frequency:
IBM, VESA, HP, Sun, Mac
30 kHz - 64 kHz for Digital
30 kHz - 82 kHz for Analog
56 Hz - 75 Hz
Vert. Frequency:
27
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 28 Thursday, October 5, 2000 8:45 AM
Environment
Temperature:
Operating:
Storage:
10 to 35° C (50 to 95° F)
- 20 to 60° C (-4 to 140° F)
- 20 to 60° C (-4 to 140° F)
Shipping:
Humidity:
Operating:
Storage:
10 to 80%
5 to 95%
5 to 95%
Shipping:
28
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 29 Thursday, October 5, 2000 8:45 AM
Warranty Statements
Warranty period - Three (3) years
Your Installation Diskette includes translation of IBM’s Statement of
Warranty in following languages:
Worldwide Statement of Warranty
(Except Turkiye, U.S., Puerto Rico and Canada):
Z1255697.ara.html
Z1255697.bra.html
Z1255697.bul.html
Z1255697.chi.html
Z1255697.cro.html
Z1255697.cze.html
Z1255697.dan.html
Z1255697.dut.html
Z1255697.eng.html
Z1255697.fin.html
Z1255697.fre.html
Z1255697.ger.html
Z1255697.gre.html
Z1255697.heb.html
Z1255697.hun.html
Z1255697.ita.html
Z1255697.jap.html
Z1255697.kor.html
Z1255697.nor.html
Z1255697.pol.html
Z1255697.por.html
Z1255697.rus.html
Z1255697.sla.html
Arabic
Brazilian portuguese
Bulgarian
Chinese
Croatian
Czech
Danish
Dutch
English
Finnish
French
German
Greek
Hebrew
Hungarian
Italian
Japanese
Korean
Norwegian
Polish
Portuguese
Russian
Slovakian
29
Download from Www.Somanuals.com. All Manuals Search And Download.
T84H_setup0926_final.fm Page 30 Thursday, October 5, 2000 8:45 AM
Z1255697.sle.html
Z1255697.spa.html
Z1255697.swe.html
Z1255697.tai.html
Slovenian
Spanish
Swedish
Taiwanese
Turkiye Statement of Warranty:
Z1255698.tur.html
Z1255698.eng.html
Turkish
English
United States, Puerto Rico and Candada Statement of Limited Warranty:
Z1254753.eng.html
Z1254753.fca.html
English
French Canadian
30
Download from Www.Somanuals.com. All Manuals Search And Download.
|