Operator’s manual
426LST 430LS
Please read the operator’s manual carefully and make sure you understand the instructions
before using the machine.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
Note the following before
starting:
KEY TO SYMBOLS
Symbols ................................................................
CONTENTS
2
Please read the operator’s manual carefully.
Maintenance, replacement, or repair of the emission
control devices and system may be performed by any
nonroad engine repair establishment or individual.
Contents ...............................................................
Note the following before starting: ........................
INTRODUCTION
3
3
WARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
Dear customer! .....................................................
WHAT IS WHAT?
4
5
!
What is what? .......................................................
GENERAL SAFETY PRECAUTIONS
Important ..............................................................
Personal protective equipment .............................
Machine′s safety equipment .................................
Cutting equipment ................................................
ASSEMBLY
6
6
7
9
WARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
Fitting the loop handle .......................................... 10
Assembling the cutting equipment ....................... 10
Fitting the trimmer guard and trimmer head ......... 10
FUEL HANDLING
Your warranty may not cover damage or
liability caused by the use of non-
authorized accessories or replacement
parts.
Fuel safety ............................................................ 11
Fuel ...................................................................... 11
Fueling .................................................................. 12
STARTING AND STOPPING
WARNING! A clearing saw, brushcutter
or trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
Check before starting ........................................... 13
Starting and stopping ........................................... 13
WORKING TECHNIQUES
General working instructions ................................ 15
MAINTENANCE
Carburetor ............................................................ 17
Muffler .................................................................. 17
Cooling system ..................................................... 17
Spark plug ............................................................ 17
Fuel filter ............................................................... 18
Air filter ................................................................. 18
Bevel gear ............................................................ 18
Maintenance schedule ......................................... 19
TECHNICAL DATA
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal and Californian emissions requirements.
Technical data ...................................................... 20
FEDERAL AND CALIFORNIA EMISSIONS
CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS 21
The engine exhaust from this product
contains chemical known to the State
of California to cause cancer, birth
defects or other reproductive harm.
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear customer!
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different
products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first
motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working
today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as
well as for building and construction industry.
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the
retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and
the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the
borrower or buyer gets the operator′s manual, so they will also know how to properly maintain and use it.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
10
8
11
7
16
15
6
9
12
5
14
13
3
17
2
19
18
4
1
What is what?
1
2
3
4
5
6
7
8
9
Trimmer head
11 Cylinder cover
12 Starter handle
13 Fuel tank
Grease filler cap, bevel gear
Bevel gear
Cutting attachment guard
Shaft
14 Air purge
15 Choke control
16 Air filter cover
Loop handle
Stop switch
17 Combination spanner
18 Locking pin
Throttle lockout
Throttle control
19 Operator’s manual
10 Spark plug cap and spark plug
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Important
Personal protective equipment
IMPORTANT!
IMPORTANT!
The machine is only designed for trimming grass.
A clearing saw, brushcutter or trimmer can be
dangerous if used incorrectly or carelessly, and can
cause serious or fatal injury to the operator or others. It
is extremely important that you read and understand the
contents of this operator’s manual.
The only accessories you can operate with this engine
unit are the cutting attachments we recommend in the
chapter on Technical data.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
Wear personal protective equipment. See instructions
under the heading ”Personal protective equipment”.
Never use a machine that has been modified in any way
from its original specification.
WARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
Never use a machine that is faulty.Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the heading Maintenance.
!
HEARING PROTECTION
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition
lead are undamaged to avoid the risk of electric shock.
Wear hearing protection that provides adequate noise
reduction.
The machine operator must ensure that no people or
animals come closer than 15 metres while working.
When several operators are working in the same area
the safety distance should be at least twice the tree
height and no less than 15 metres.
EYE PROTECTION
Always wear approved eye protection. If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with standard
ANSI Z87.1 in the USA or EN 166 in EU countries.
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants.To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
WARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
!
BOOTS
Wear sturdy, non-slip boots.
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
CLOTHING
Throttle lockout
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants. Do not wear jewellery, shorts
sandals or go barefoot.Secure hair so it is above shoulder
level.
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock
(A) (i.e.when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle
control and the throttle lockout both move back to their
original positions. This movement is controlled by two
independent return springs.This arrangement means that
the throttle control is automatically locked at the idle
setting.
FIRST AID KIT
Always have a first aid kit nearby.
A
Machine′s safety equipment
This section describes the machine′s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?” section to locate where this equipment is
positioned on your machine.
B
•
•
•
•
Make sure the throttle control is locked at the idle
setting when the throttle lockout is released.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
Press the throttle lockout and make sure it returns to
its original position when you release it.
Check that the throttle control and throttle lockout
move freely and that the return springs work properly.
IMPORTANT!
See instructions under the heading Start. Start the
machine and apply full throttle. Release the throttle
and check that the cutting attachment stops and
remains at a standstill. If the cutting attachment
rotates with the throttle in the idle position then the
carburettor idle setting must be checked. See
instructions under the heading Maintenance.
All servicing and repair work on the machine requires
special training.This is especially true of the machine′s
safety equipment. If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee
the availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
Stop switch
Use the stop switch to switch off the engine.
WARNING! Never use a machine with
faulty safety equipment.The machine’s
!
safety equipment must be checked and
maintained as described in this section.
If your machine fails any of these checks
contact your service agent to get it
repaired.
U N
R
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting.
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
For mufflers it is very important that you follow the
instructions on checking, maintaining and servicing your
machine.
Cutting attachment guard
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
This guard is intended to prevent loose objects from being
thrown towards the operator.The guard also protects the
operator from accidental contact with the cutting
attachment.
If the muffler on your machine is fitted with a spark
arrestor screen this must be cleaned regularly. A blocked
screen will cause the engine to overheat and may lead to
serious damage.
WARNING! The inside of the muffler
contain chemicals that may be
!
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
WARNING! Bear in mind that:
!
The exhaust fumes from the engine are
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
hot and may contain sparks which can
start a fire. Never start the machine
indoors or near combustible material!
WARNING! Never use a cutting
attachment without an approved guard.
!
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
In countries that have a warm and dry climate there is a
significant risk of fire.We therefore fit certain mufflers with
a spark arrestor screen. Check whether the muffler on
your machine is fitted with this kind of screen.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Trimmer head
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
IMPORTANT!
Always ensure the trimmer cord is wound tightly and
evenly around the drum, otherwise the machine will
generate harmful vibration.
•
•
•
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
•
Only use the recommended trimmer heads and
trimmer cords. These have been tested by the
manufacturer to suit a particular engine size. This is
especially important when a fully automatic trimmer
head is used. Only use the recommended cutting
attachment. See the chapter on Technical data.
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to
check the correct way to load the cord and the correct
cord diameter.
WARNING! Always stop the engine
before doing any work on the cutting
!
•
•
Smaller machines generally require small trimmer
heads and vice versa. This is because when clearing
using a cord the engine must throw out the cord
radially from the trimmer head and overcome the
resistance of the grass being cleared.
attachment.This continues to rotate even
after the throttle has been released.
Ensure that the cutting attachment has
stopped completely and disconnect the
HT lead from the spark plug before you
start to work on it.
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of
the same diameter.
WARNING! A faulty cutting attachment
may increase the risk of accidents.
•
•
Make sure that the cutter on the trimmer guard is
intact.This is used to cut the cord to the correct length.
!
To increase the life of the cord it can be soaked in
water for a couple of days. This will make the line
tougher so that it lasts longer.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting the loop handle
Fitting the trimmer guard and
trimmer head
•
Position the handle on the shaft. Note that the handle
must be mounted below the arrow on the shaft.
•
Fit the correct trimmer guard (A) for use with the
trimmer head.
A
•
•
Tighten the two screws.
Fit the drive disc (B) on the output shaft.
•
Slide the spacer into the slot in the loop handle.Fit the
nut and screw. Tighten.
Assembling the cutting
equipment
WARNING! Never use a cutting
attachment without an approved guard.
!
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
•
Turn the blade shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Screw on the trimmer head (D) in the opposite
direction to the direction of rotation.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Gasoline
Fuel safety
Never start the machine:
1
2
If you have spilled fuel on it. Wipe off the spillage and
allow remaining fuel to evaporate.
CAUTION! Always use a quality gasoline/oil mixture with
an octane rating of at least 87 octane ((RON+MON)/2). If
your machine is equipped with a catalytic converter (see
chapter on Technical data) always use a good quality
unleaded gasoline/oil mixture. Leaded gasoline will
destroy the catalytic converter.
If you have spilled fuel on yourself or your clothes,
change your clothes.Wash any part of your body that
has come in contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.
Use low-emission gasoline, also known as alkylate
gasoline, if it is available.
Transport and storage
•
Store and transport the machine and fuel so that there
is no risk of any leakage or fumes coming into contact
with sparks or naked flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
•
•
When storing and transporting fuel always use
approved containers intended for this purpose.
When storing the machine for long periods the fuel
tank must be emptied. Contact your local gas station
to find out where to dispose of excess fuel.
This engine is certified to operate on unleaded
gasoline.
•
The lowest recommended octane grade is 87
((RON+MON)/2). If you run the engine on a lower
octane grade than 87 so-called knocking can occur.
This gives rise to a high engine temperature and
increased bearing load, which can result in serious
engine damage.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
•
Secure the machine during transport.
•
When working at continuous high revs a higher octane
rating is recommended.
WARNING!Take care when handling fuel.
Bear in mind the risk of fire, explosion
and inhaling fumes.
Two-stroke oil
!
•
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two stroke-engines.
Fuel
CAUTION! The machine is equipped with a two-stroke
engine and must always been run using a mixture of
gasoline and two-stroke engine oil. It is important to
accurately measure the amount of oil to be mixed to
ensure that the correct mixture is obtained. When mixing
small amounts of fuel, even small inaccuracies can
drastically affect the ratio of the mixture.
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
•
•
Never use oil intended for four-stroke engines.
Mixing ratio
1:50 (2%) with HUSQVARNA two-stroke oil.
Two-stroke oil, litre
Gasoline, litre
WARNING! Fuel and fuel fumes are
highly inflammable and can cause
serious injury when inhaled or allowed to
come in contact with the skin. For this
reason observe caution when handling
fuel and make sure there is adequate
ventilation.
2% (1:50)
!
5
0,10
10
0,20
15
0,30
20
0,40
US gallon
US fl. oz.
2 1/2
6 1/2
12 7/8
1
2 1/2
5
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Fueling
Mixing
•
Always mix the gasoline and oil in a clean container
intended for fuel.
•
Always start by filling half the amount of the gasoline
to be used. Then add the entire amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount of
gasoline.
WARNING! Taking the following
precautions, will lessen the risk of fire:
!
•
Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refuelling.
Always stop the engine and let it cool for
a few minutes before refuelling.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refuelling.
Always move the machine away from the
refuelling area before starting.
•
•
Do not mix more than one month’s supply of fuel at a
time.
•
•
Clean the area around the fuel cap. Contamination in
the tank can cause operating problems.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Ensure that the fuel is well mixed by shaking the
container before filling the tank.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Primer bulb: Press the air purge repeatedly until fuel
begins to fill the bulb. The bulb need not be completely
filled.
Check before starting
•
Check that the trimmer head and trimmer guard are
not damaged or cracked.Replace the trimmer head or
trimmer guard if they have been exposed to impact or
are cracked.
•
•
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
Choke: Set the choke control in the choke position.
WARNING! The complete clutch cover
and shaft must be fitted before the
machine is started, otherwise the clutch
can come loose and cause personal
injury.
!
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the
cutting attachment cannot come into
contact with any object.
Make sure no unauthorised persons are
in the working area, otherwise there is a
risk of serious personal injury.The safety
distance is 15 metres.
WARNING! When the engine is started
with the choke in choke position the
cutting attachment will start to rotate
immediately.
Starting
!
Ignition: Set the stop switch to the start position.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord. Never wrap the
starter cord around your hand
Reset the choke when the engine fires, repeat pulling the
cord until the engine starts.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
CAUTION! Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
Stopping
Stop the engine by switching off the ignition.
U N
R
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
6
Always hold the machine with both hands. Hold the
machine on the right side of your body.
General working instructions
IMPORTANT!
This section takes up the basic safety precautions for
working with a trimmer.
If you encounter a situation where you are uncertain
how to proceed you should ask an expert. Contact your
dealer or your service workshop.
Avoid all usage which you consider to be beyond your
capability.
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
Basic safety rules
7
8
9
Keep the cutting attachment below waist level.
The engine must be switched off before moving.
1
•
Look around you:
To ensure that people, animals or other things cannot
affect your control of the machine.
Never put the machine down with the engine running
unless you have it in clear sight.
•
To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects
that are thrown out by the cutting attachment.
WARNING! Neither the operator of the
machine nor anyone else may attempt to
!
•
NB! Do not use the machine unless you are able to
call for help in the event of an accident.
remove the cut material while the engine
is running or the cutting equipment is
rotating, as this can result in serious
injury.
2
Inspect the working area. Remove all loose objects,
such as stones, broken glass, nails, steel wire, string,
etc. that could be thrown out or become wrapped
around the cutting attachment.
Stop the engine and cutting equipment
before you remove material that has
wound around the blade shaft as
otherwise there is a risk of injury.The
bevel gear can get hot during use and
may remain so for a while afterwards.You
could get burnt if you touch it.
3
4
Do not use the machine in bad weather, such as
dense fog, heavy rain, strong wind, intense cold, etc.
Working in bad weather is tiring and often brings
added risks, such as icy ground, unpredictable felling
direction, etc.
Make sure you can move and stand safely. Check the
area around you for possible obstacles (roots, rocks,
branches, ditches, etc.) in case you have to move
suddenly. Take great care when working on sloping
ground.
WARNING! Watch out for thrown objects.
Always wear approved eye protection.
!
Never lean over the cutting attachment
guard. Stones, rubbish, etc. can be
thrown up into the eyes causing
blindness or serious injury.
Keep unauthorised persons at a
distance. Children, animals, onlookers
and helpers should be kept outside the
safety zone of 15 m. Stop the machine
immediately if anyone approaches. Never
swing the machine around without first
checking behind you to make sure no-
one is within the safety zone.
5
Keep a good balance and a firm foothold.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Clearing
Basic working techniques
•
The clearing technique removes all unwanted
vegetation. Keep the trimmer head just above the
ground and tilt it. Let the end of the cord strike the
ground around trees, posts, statues and the like.
CAUTION! This technique increases the wear on the
cord.
Always slow the engine to idle speed after each working
operation. Long periods at full throttle without any load on
the engine can lead to serious engine damage.
WARNING! Sometimes branches or
grass get caught between the guard and
cutting attachment. Always stop the
engine before cleaning.
!
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
!
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition.These
symptoms normally appear in the
fingers, hands or wrists.The risk
increases at low temperatures.
•
•
The cord wears quicker and must be fed forward more
often when working against stones, brick, concrete,
metal fences, etc., than when coming into contact with
trees and wooden fences.
When trimming and clearing you should use less than
full throttle so that the cord lasts longer and to reduce
the wear on the trimmer head.
Cutting
• The trimmer is ideal for cutting grass that is difficult to
Grass trimming with a trimmer head
reach using a normal lawn mower. Keep the cord
parallel to the ground when cutting.Avoid pressing the
trimmer head against the ground as this can ruin the
lawn and damage the tool.
Trimming
•
Hold the trimmer head just above the ground at an
angle. It is the end of the cord that does the work. Let
the cord work at its own pace. Never press the cord
into the area to be cut.
•
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting.
Constant contact of this type can cause damage and
wear to the trimmer head.
Sweeping
• The fan effect of the rotating cord can be used for
•
•
The cord can easily remove grass and weeds up
against walls, fences, trees and borders, however it
can also damage sensitive bark on trees and bushes,
and damage fence posts.
quick and easy clearing up. Hold the cord parallel to
and above the area to be swept and move the tool to
and fro.
Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
•
When cutting and sweeping you should use full
throttle to obtain the best results.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
On mufflers without a catalytic converter the screen
Carburetor
should be cleaned weekly, or replaced if necessary. On
mufflers fitted with a catalytic converter the screen should
be checked, and if necessary cleaned, monthly. If the
screen is damaged it should be replaced. If the screen
is frequently blocked, this can be a sign that the
performance of the catalytic converter is impaired.
Contact your dealer to inspect the muffler. A blocked
screen will cause the machine to overheat and result in
damage to the cylinder and piston.
Adjustment of the idle speed
Check that the air filter is clean. When the idle speed is
correct, the cutting attachment should not rotate. If
adjustment is required, close (turn clockwise) the idle
adjustment screw T, with the engine running, until the
cutting attachment starts to rotate. Open (turn
anticlockwise) the screw until the cutting attachment
stops. The idle speed is correctly set when the engine
runs smoothly in all positions, and there is a clear margin
to the speed at which the cutting attachment starts to
rotate.
CAUTION! Never use a machine with a defective muffler.
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
1
T
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
!
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
2
The cooling system consists of:
1
2
Cooling fins on the cylinder.
Cooling air intake
Muffler
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
Spark plug
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.
The spark plug condition is influenced by:
•
•
Incorrect carburetor adjustment.
An incorrect fuel mixture (too much or incorrect type
of oil).
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you
should clean the screen at least once a week.This is best
done with a wire brush.
•
A dirty air filter.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0,6-0,7 mm
(426LST) / 0,9-1,0 mm (430LS).The spark plug should be
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
replaced after about a month in operation or earlier if
necessary.
•
Excessive fuel consumption.
0,6 - 0,7 mm (426 LST)
0,9 - 1,0 mm (430 LS)
Clean the filter every 25 hours, or more regularly if
conditions are exceptionally dusty.
CAUTION! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the piston/
cylinder. Check that the spark plug is fitted with a
suppressor.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced
with a new one at regular intervals. A damaged air filter
must always be replaced.
Fuel filter
Bevel gear
When the engine runs short of fuel supply, check the fuel
cap and the fuel filter for blockage.
There is a grease nipple on the gearbox. Use a grease
gun to top up with grease.This should be carried out after
approximately every 25 working hours. Use Husqvarna
special grease.
Remove the drive disc or the side bolt in the gear cae
before installing new grease to arrange for old grease to
exit.
Air filter
CAUTION! When removing and installing the drive disc,
use care not to allow any dirt and dust entering into the
gear case.
The air filter must be regularly cleaned to remove dust
and dirt in order to avoid:
CAUTION! Use only HUSQVARNA replacement parts.
Use of other brands of replacement parts can cause
damage to your unit or injury to the operator or others.
Your warranty does not cover damage or liability caused
by the use of accessories and/or attachments not
specifically recommended by HUSQVARNA.
•
•
•
•
Carburettor malfunctions
Starting problems
Loss of engine power
Unnecessary wear to engine parts
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section.
Daily
maintenance
Weekly
maintenance
Monthly
maintenance
Maintenance
Clean the outside of the machine.
X
Make sure the throttle trigger lock and the throttle function
correctly from a safety point of view.
X
Check that the stop switch works correctly.
Check that the cutting attachment does not rotate at idle.
Clean the air filter. Replace if necessary.
X
X
X
Check that the guard is undamaged and not cracked. Replace
the guard if it has been exposed to impact or is cracked.
X
Check that the trimmer head is undamaged and not cracked.
Replace the trimmer head if necessary.
X
X
X
Check that nuts and screws are tight.
Check that there are no fuel leaks from the engine, tank or fuel
lines.
Check the starter and starter cord.
X
X
Check that the vibration damping elements are not damaged.
Clean the outside of the spark plug. Remove it and check the
electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the
spark plug. Check that the spark plug is fitted with a suppressor.
X
Clean the machine’s cooling system.
X
X
X
X
Clean or replace the spark arrestor screen on the muffler (only
applies to mufflers without a catalytic converter).
Clean the outside of the carburettor and the space around it.
Check that the bevel gear is filled three-quarters full with
lubricant. Fill if necessary using special grease.
Check the fuel filter from contamination and the fuel hose from
cracks or other defects. Replace if necessary.
X
X
X
Check all cables and connections.
Check the clutch, clutch springs and the clutch drum for wear.
Replace if necessary by an autorized service workshop.
Replace the spark plug. Check that the spark plug is fitted with a
suppressor.
X
X
Check and clean the spark arrestor screen on the muffler (only
applies to mufflers fitted with a catalytic converter).
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
426LST
430LS
Motor
Cylinder displacement, cu.in/cm3
Cylinder bore, inch/mm
Stroke, inch/mm
1,55/25,4
1,34/34
1,10/28
3000
1,80/29,5
1,50/38
1,03/26
3000
Idle speed, rpm
Recommended max. speed, rpm
Speed of output shaft, rpm
11500
5500
10000
6850
Max. engine output, acc. to ISO 8893, kW/ rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
0,87/7500
No
1,03/8500
No
No
No
Spark plug
NGK CMR7H
NGK CMR7H
Electrode gap, inch/mm
Fuel and lubrication system
Fuel tank capacity, US pint/litre
Weight
0,024-0,028/0,6-0,7 0,035-0,039/0,9-1,0
1,37/0,65
1,52/0,72
13,2/6,0
Weight without fuel, cutting attachment and guard, Lbs/kg 12,6/5,7
Approved accessories
Type
Cutting attachment guard, Art. no.
Arbor shaft thread M10
T25
575 38 41-01
575 38 41-01
575 38 41-01
Trimmer head
S35
T35, T35x
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL AND CALIFORNIA EMISSIONS CONTROLWARRANTY STATEMENT
WARRANTY COMMENCEMENT DATE
YOUR WARRANTY RIGHTS AND
OBLIGATIONS
The warranty period begins on the date the engine or
equipment is delivered to an ultimate purchaser.
The EPA (U.S. Environmental Protection Agency), CARB
LENGTH OF COVERAGE
(California Air Resources Board), Environment Canada
and Husqvarna Forest & Garden are pleased to explain
the emissions control system’s warranty on your 2009 and
later small off-road engine. In U.S. and Canada, new
equipment that use small off-road engines must be
designed, built, and equipped to meet the applicable
Federal or Californian stringent anti-smog standards.
Husqvarna Forest & Garden must warrant the emissions
control system on your small off-road engine for the
period listed below provided there has been no abuse,
neglect or improper maintenance of your equipment.Your
emissions control system may include parts such as the
carburetor, ignition system, catalytic converter, fuel tank,
filters and other associated components. Also, included
may be hoses, belts, connectors, sensors, and other
emission-related assemblies. Where a warrantable
condition exists, Husqvarna Forest & Garden will repair
your small off-road engine at no cost to you including
diagnosis, parts and labor.
Husqvarna Forest & Garden warrants to the ultimate
purchaser and each subsequent owner that the engine or
equipment is designed, built, and equipped so as to
conform with all applicable regulations adopted by EPA
and CARB, and is free from defects in materials and
workmanship that causes the failure of a warranted part
for a period of two years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or
replacement of any warranted part under the warranty
must be performed at no charge to the owner at a
warranty station. Warranty services or repairs will be
provided at all Husqvarna Forest & Garden distribution
centers that are franchised to service the subject engines.
Throughout the emissions warranty period of two years,
Husqvarna Forest & Garden must maintain a supply of
warranted parts sufficient to meet the expected demand
for such parts.
MANUFACTURER′S WARRANTY
COVERAGE
WARRANTY PERIOD Any warranted part that is
scheduled for replacement as required in the
The emissions control system is warranted for two years.
If any emissions-related part on your equipment is
defective, the part will be repaired or replaced by
Husqvarna Forest & Garden.
maintenance schedule, is warranted for the period of time
prior to the first scheduled replacement point for that part.
If the part fails prior to the first scheduled replacement,
the part will be repaired or replaced by Husqvarna Forest
& Garden at no cost. Any such part repaired or replaced
under warranty is warranted for the remainder of the
period prior to the first scheduled replacement point for
the part. Any warranted part that is not scheduled for
replacement as required in the maintenance schedule, is
warranted for two years. If any such part fails during the
period of warranty coverage, it will be repaired and
replaced by Husqvarna Forest & Garden at no cost. Any
such part repaired or replaced under the warranty is
warranted for the remaining warranty period. Any
warranted part that is scheduled only for regular
inspection in the maintenance schedule will be warranted
for a period of two years. A statement in such written
instructions to the effect of ”repair or replace as
necessary” will not reduce the period of warranty
coverage. Any such part repaired or replaced under
warranty will be warranted for the remaining warranty
period.
OWNER′S WARRANTY
RESPONSIBILITIES
•
As the small off-road engine owner, you are
responsible for performance of the required
maintenance listed in your operator’s manual.
Husqvarna Forest & Garden recommends that you
retain all receipts covering maintenance on your small
off-road engine, but Husqvarna Forest & Garden
cannot deny warranty solely for the lack of receipts or
your failure to ensure the performance of all
scheduled maintenance.
•
•
As the small off-road engine owner, you should
however be aware that Husqvarna Forest & Garden
may deny you warranty coverage if your small off-road
engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road
engine to a Husqvarna Forest & Garden distribution
center or service center as soon as the problem
exists.The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days. If
you have any questions regarding your warranty
coverage, you should contact Husqvarna Forest &
Garden at 1-800-487-5951 or visit
DIAGNOSIS The owner must not be charged for
diagnostic labor that leads to the determination that a
warranted part is in fact defective, provided that such
diagnostic work is performed at a warranty station.
CONSEQUENTIAL DAMAGES Husqvarna Forest &
Garden is liable for damages to other engine components
proximately caused by a failure under warranty of any
warranted part.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL AND CALIFORNIA EMISSIONS CONTROLWARRANTY STATEMENT
EMISSION WARRANTY PARTS LIST
1
2
3
Carburetor and internal parts
Intake pipe, airfilter holder and carburetor bolts.
Airfilter and fuelfilter covered up to maintenance
schedule.
4
5
6
Spark Plug, covered up to maintenance schedule
Ignition Module
Fuel tank
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
ADD -ON OR MODIFIED PARTS
Add-on or modified parts that are not exempted by CARB
or EPA may not be used. The use of any non-exempted
add-on or modified parts will be grounds for disallowing a
warranty claim. Husqvarna Forest & Garden will not be
liable to warrant failures of warranted parts caused by the
use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5951 or visit
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any replacement part may be used in the performance of
any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not
reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all
required maintenance, as defined in the operator’s
manual.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
T25
1
2
3
6,0 m
18'
10 cm
4"
3,05 m
9'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
3
8,5 m
28'
10 cm
4"
4,2 m
14'
4
5
7
6
8
"Clic"
10
11
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
4,25 m
14'
4,25 m
14'
4
3
5
15 cm
6"
B
A
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
T35, T35x
1
2
3
8,5 m
28'
10 cm
4"
4,3 m
14'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1153174-95
´®z+U1Q¶59¨
´®z+U1Q¶59¨
2009-11-30
Download from Www.Somanuals.com. All Manuals Search And Download.
|