INSTALLATION and MAINTENANCE INSTRUCTIONS
SHO TWIN SPRING STACK ELECTRIC CABLE REELS
MAINTENANCE
All units are provided with right hand rotation unless otherwise
specified. This means that cable is pulled off spool top left
or bottom right (spool rotates clockwise to wind cable) when
viewing spring end of reel. See diagram on parts page.
Periodically: A. Use compressed air to clean collector assembly
and inside of collector housing. Inspect collector assembly for
brush wear and pitted slip rings.
B. Inspect cable for wear and
Clock-type springs provide power for automatic cable take-up.
Spring must be pretensioned at time of installation to insure
that tension is applied to cable at all times. A tension adjustment
spanner wrench is provided with each reel.
“IN” with 2/3
cable off reel–
SPRING OK
BROKEN SPRING
INDICATORS
check mounting bolts and other
hardware for tightness.
C. Check for broken springs by
pulling about 2/3 cable off reel
“OUT” with 2/3
cable off reel–
SPRING
BROKEN
and observing “Broken Spring
WARNING
Indicators” on sides of spring
canisters. See Fig. 3.
Some reels with large or multiple springs are equipped with
a ratcheted adjustment wrench. Follow separate instruc-
tions for its use. Failure to use ratcheted wrench, on reels
so equipped, could result in serious personal injury.
NOTE: Bearings and springs
Figure 3
are prelubricated and require no
periodic maintenance.
WARNING
WARNING
Do not attempt to relieve spring tension using spanner
wrench. Doing so may result in personal injury.
Do not attempt to remove spring from its housing. Clock-
type springs can be dangerous to handle. Removal of
spring from housing could result in personal injury.
INSTALLATION
SPRING REPLACEMENT
1. Insure that machinery to be serviced by reel is at position
closest to reel.
The unique SAFETYCHANGE® spring motor consists of a
spring and hub sealed within a housing. A replacement spring is
supplied sealed in its housing and the old unit should be discarded
completely.
2. Securely mount reel in desired position using 3/8"(M10)
bolts. Be sure spool is aligned with cable run.
3. Position optional cable guide, if reel is so equipped.
4. Connect free end of cable to junction box on machine or
adjust cable stop so that desired length of cable
extends from reel.
1. Turn off all electric power.
2. Disconnect cable from machine junction box.
3. Wind all cable onto reel to relieve all spring tension.
4. Remove inspection cover from face of spring housing.
5. Rotate spool clockwise and observe inner shaft. Shaft should
rotate clockwise and hub (with spring attached) should
remain stationary.
5. Remove cover plate on spring housing to expose
shaft and spring hub. (See Figure 1).
6. Insert spanner wrench into holes in spring hub (Fig 2).
Rotate wrench counterclockwise (for standard rotation).
Number of 360º turns should match last digit in model
number on serial plate. If model number includes an “R”,
reel is reverse rotation and wrench must be rotated
clockwise. (See EXPLANATION on parts list page.)
NOTE: Do not attempt to remove spring if
resistance is met or hub tends to rotate with shaft.
Continue to rotate spool and strike end of shaft several sharp
blows with a lead hammer or rubber mallet until shaft rotates
freely and hub remains stationary.
6. Remove (4) nuts which secure spring motor(s) to frame.
7. Slide spring motor(s) off shaft and discard.
NOTE: On multi-spring reels, be sure to remove and save
dowel pins which connect one spring hub with another. Also
remove snap rings on shaft between spring housings.
8. Install replacement spring motor(s), pawls and pawl springs.
NOTE: Pawl springs must be located between the pawls
and the deepest section of the shaft grooves. Make sure that
pawls and pawl springs are inserted flush with ends of shaft and
hub or they may rub against inspection cover.
NOTE: If reel is equipped with ratcheted adjustment
wrench, follow instructions on separate sheet.
NOTE: On reels containing more than one spring, the hubs
are connected at the factory. Therefore, by tightening the
outer spring, the inside spring(s) will be tightened.
7. Remove collector cover and connect individual supply
conductors to collector terminals.
COUNTER-
CLOCKWISE
FOR STANDARD
ROTATION
SPRING
HOUSING
SPRING
PAWL
COVER
PLATE
HUB
SPOOL
SHAFT
(Spring not
shown)
SPRING
Install
against flat
SHAFT
GROOVE
SPRING
HUB
END VIEW
SIDE VIEW
SPANNER
WRENCH
Figure 2
Figure 1
9. Tighten nuts (and extension bolts) securing spring
housing(s) to reel frame.
CAUTION
10. Connect free end of cable to junction box on machine or adjust
cord stop so that desired length of cord extends from reel.
Do not exceed number of turns indicated on
serial plate. Over-tensioning can cause a
broken spring, sheared shaft or other damage.
11. Tension spring with spanner wrench. Refer to
INSTALLATION section.
12. Replace inspection cover.
CONTINUED ON BACK PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
SHO TWIN SPRING ELECTRIC CABLE REEL REPLACEMENT PARTS LIST
NOTE: Applicable mounting hardware included with each kit.
ITEM KIT NO.
DESCRIPTION
QTY.
ITEM KIT NO.
DESCRIPTION
QTY.
1
020554
Frame Assembly-SHO
1
18
18
18
18
18
18
18
18
18
18
18
012459
012460
012461
012462
012463
012464
012465
012466
012467
021764
021765
Cable Connector–.38 to .50 Dia. Cable
Cable Connector–.50 to .62 Dia. Cable
Cable Connector–.62 to .75 Dia. Cable
Cable Connector–.75 to .88 Dia. Cable
Cable Connector–.88 to 1.00 Dia. Cable
Cable Connector–1.00 to 1.12 Dia. Cable
Cable Connector–1.12 to 1.25 Dia. Cable
Cable Connector–1.25 to 1.38 Dia. Cable
Cable Connector–1.38 to 1.50 Dia. Cable
Cable Connector–1.50 to 1.62 Dia. Cable
Cable Connector–1.62 to 1.75 Dia. Cable
1
1
1
1
1
1
1
1
1
1
1
2
027853
Collector Shaft -
14-17" Dia. Spool Wrapper
Collector Shaft -
1
2
3
4
027854
021752
012402
1
1
1
18" & Over Dia. Spool Wrapper
Bearing Kit–2" bore
(Includes housing and gasket)
Bearing Kit–2" Bore
(Includes housing and gasket)
5
6
105060
012401
Retaining Ring
1
2
Bearing Kit–1.75" Bore
(Includes housing and gasket)
19
02176301
Chain Cover Kit
(Includes cover, gasket and hardware)
1
7
8
021753
Spring Shaft Kit
1
(Includes spring shaft, stub shaft drive pin, retaining ring)
20
21
045494
101652
Collector Entrance Assembly
Pipe Plug
1
1
021754
Sprocket Kit, Ratio AA
(Includes two sprockets and keys)
Sprocket Kit, Ratio AB
1
8
8
8
8
021755
021756
021757
021758
1
1
1
1
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
012285
012286
012287
012288
012289
012290
012291
012292
012293
012294
012295
012296
012297
012298
012299
012300
012376
012377
037194
037294
037295
012304
012381
012382
012383
012384
Collector Assembly, 2 Pole, 35 Amp
Collector Assembly, 3 Pole, 35 Amp
Collector Assembly, 4 Pole, 35 Amp
Collector Assembly, 6 Pole, 35 Amp
Collector Assembly, 8 Pole, 35 Amp
Collector Assembly, 10 Pole, 35 Amp
Collector Assembly, 12 Pole, 35 Amp
Collector Assembly, 14 Pole, 35 Amp
Collector Assembly, 16 Pole, 35 Amp
Collector Assembly, 20 Pole, 35 Amp
Collector Assembly, 24 Pole, 35 Amp
Collector Assembly, 30 Pole, 35 Amp
Collector Assembly, 36 Pole, 35 Amp
Collector Assembly, 2 Pole, 75 Amp
Collector Assembly, 3 Pole, 75 Amp
Collector Assembly, 4 Pole, 75 Amp
Collector Assembly, 6 Pole, 75 Amp
Collector Assembly, 8 Pole, 75 Amp
Collector Assembly, 2 Pole, 125 Amp
Collector Assembly, 3 Pole, 125 Amp
Collector Assembly, 4 Pole, 125 Amp
Collector Assembly, 2 Pole, 200 Amp
Collector Assembly, 3 Pole, 200 Amp
Collector Assembly, 4 Pole, 200 Amp
Collector Assembly, 6 Pole, 200 Amp
Collector Assembly, 8 Pole, 200 Amp
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Sprocket Kit, Ratio AC
Sprocket Kit, Ratio AD
Sprocket Kit, Ratio AE
9
021759
Idler Kit
1
(Includes sprocket, shaft, tensioner bar,
locking collar and mounting hardware)
10
021760
Roller Chain Kit
(Includes connecting link)
1
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
012209
01220901
012210
01221001
012211
01221101
012212
01221201
012213
01221301
012214
01221401
012371
01237101
014619
Stub Shaft, Std. Rot. (801)
Stub Shaft, Rev. Rot. (801)
Stub Shaft, Std. Rot. (802)
Stub Shaft, Rev. Rot. (802)
Stub Shaft, Std. Rot. (803)
Stub Shaft, Rev. Rot. (803)
Stub Shaft, Std. Rot. (804)
Stub Shaft, Rev. Rot. (804)
Stub Shaft, Std. Rot. (1001)
Stub Shaft, Rev. Rot. (1001)
Stub Shaft, Std. Rot. (1002)
Stub Shaft, Rev. Rot. (1002)
Stub Shaft, Std. Rot. (1003)
Stub Shaft, Rev. Rot. (1003)
Stub Shaft, Std. Rot. (1004)
Stub Shaft, Rev. Rot. (1004)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
01461901
12
017049
Spring Motor Kit, Std. Rot. -80
AR
23
012440
Brush Kit (35 Amp)
(Each kit includes 4 brushes and 4 fingers)
Brush Kit (75 Amp)
AR
(Includes one spring assembly, snap ring, pawl,
pawl spring, hub cover and gasket)
Spring Motor Kit, Rev. Rot. -80
23
23
012441
012443
AR
AR
12
12
12
017050
017051
017052
AR
AR
AR
Brush Kit (125 Amp/200 Amp)
Spring Motor Kit, Std. Rot. -100
Spring Motor Kit, Rev. Rot. -100
24
03742101
Collector Cover Kit (9.75" long)
(Includes Seal Ring)
1
13
012426
Pawl Kit (80 Springs)
(Includes two pawls and two pawl springs)
AR
24
24
24
24
24
03742102
03742103
03742104
03742105
03742106
Collector Cover Kit (12.75" long)
Collector Cover Kit (14.75" long)
Collector Cover Kit (19.25" long)
Collector Cover Kit (23.75" long)
Collector Cover Kit (7.00" long)
1
1
1
1
1
13
012427
Pawl Kit (100 Springs)
AR
14
14
021761
021762
Hub Lock Pin Kit–two pins (80 Springs)
Hub Lock Pin Kit–two pins (100 Springs)
AR
AR
25
26
016213
*
Seal Ring (only)
Spool Assembly
1
1
15
15
017054
017055
Extension Bolts (80 Springs)
(4 bolts per kit–less hardware)
AR
AR
Extension Bolts (100 Springs)
* Consult factory for part number of Spool Assembly and related hardware.
Please give model number and serial number to obtain correct Spool Assembly.
16
16
G64-29
G64-27
Adjustment Wrench (80 Springs)
Adjustment Wrench (100 Springs)
1
1
17
17
032805
032804
Ratchet Wrench (80 Springs)
Ratchet Wrench (100 Springs)
1
1
*SLIP RING
AMPACITY CODE
MAX
**CHAIN RATIO
CODE
MODEL NUMBER EXPLANATION
(Typical Model Number)
CHAIN
SHO 100
REEL
TYPE
7 -
4
12 - XX XX XX - AE -
1
CODE
AMPS
CODE
RATIO
CHAIN
3
7
35
75
AE
AD
AC
AB
AA
1.0:1
1.5:1
2.0:1
2.5:1
3.0:1
SPRING NUMBER NUMBER AMPACITY
MOTOR SPRINGS POLES CODE*
SPOOL
DIMENSIONS
and TYPE
PRETENSION
CODES
RATIO
CODE**
12
20
125
200
NOTE: SHO Twin Spring Reels have five to eight springs with a maximum of four in each
stack. The sum of the two stub shafts (item 11) used on each reel equals the total number
of springs. Example: An SHO1007 reel (shown above would have one 1003 and one 1004
stub shaft.
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE REMOVAL
Use the following procedure to remove worn or damaged
cable from reel prior to installation of new cable.
2.Feed one end of the cable through water-tight connector
on the main shaft inside the spool and into the slip ring
side (see drawing below).
NOTE: This may require that jacket of cable be stripped to
allow conductors to pass through shaft.
CAUTION
3.Connect individual conductors to appropriate rings on
collector using crimp fitting or similar connection method.
Failure to relieve all spring tension prior to removing
cable could result in damage to equipment or
personal injury. Follow instructions carefully
4.Tighten water-tight connector and U-bolt provided on
drum wrapper segments. Do not over-tighten.
5.Wind the cable onto the reel spool by hand rotation spool
in direction it tuns free of spring tension.
6.Connect free end of cable to machine junction box.
7.Pretension reel and complete installation as previously
described.
1.Move machine serviced by reel to a position closest to
reel. Springs will still be under pre-tension at this point.
2.Turn off all electric power.
3.Lock spool to prevent turning using wither a spool lock
mechanism or by tying off.
4.Disconnect cable from machine junction box.
5.Grip spool by hand and carefully release spool lock or
tie. Slowly unwind remaining tension.
6.Again lock or tie spool to prevent rotation.
7.Remove cable from spool. Loosen U-bolt and water-tight
connector and disconnect conductors from slip ring.
COLLECTOR REPLACEMENT
1.Turn off all power to reel.
2.Remove collector cover and gasket.
3.Disconnect electric leads to and from collector.
4.Remove drive stud bolt from bearing housing.
5.Remove pipe plug from hole in side of housing. Insert
long 1/8" Allen wrench through hold and loosen two set
screws in collector locking collar. Set screws are at 90° to
one another.
NOTE: Older reels may have lock screws which must be
removed to reach set screws holding collector to shaft.
8.Install new cable following instruction at right.
CABLE INSTALLATION
Use the following procedure to replace cable or if reel was
ordered without cable. Refer to CABLE INSTALLATION
REFERENCE DRAWING, below.
6.Slide collector off shaft.
1.Unspool new cable from shipping spool and lay out to
eliminate twist.
7.Install new collector by reversing above steps.
NOTE: This step is not essential, but will aid in winding
operation of the reel and prolong cable life.
CABLE INSTALLATION REFERENCE DRAWING
Cable
(Input)
Cable
(Output)
Collector
Reel
Shaft
Cable Gland
Thread gland into shaft.
Thread cable thru gland and
shaft. Tighten gland cover to
secure cable.
Connect leads
to collector
NOTE:
Strip cable to inside of gland
if required. Wrap leads with
electrical tape thru shaft.
Frame/Gear Case
Spool
GLEASON REEL CORP.
P.O. Box 26 • 600 South Clark St.
Mayville, WI 53050
Phone 920-387-4120 • Fax 920-387-4189
Printed in USA
Bulletin No. 052981.b
Download from Www.Somanuals.com. All Manuals Search And Download.
|