Heatiator Stove ECO ADV WS22 User Manual

Owner’s Manual  
Installation and Operation  
Model:  
ECO-ADV-WS22  
Wood Burning Stove  
WS22  
NOTICE  
DO NOT DISCARD THIS MANUAL  
Read, understand and  
follow these instructions  
for safe installation and  
operation.  
Leave this manual with  
party responsible for  
use and operation.  
Important operating  
and maintenance  
instructions included.  
WARNING  
WARNING  
HOT SURFACES!  
If the information in these instruc-  
tions is not followed exactly, a  
fire may result causing property  
damage, personal injury, or death.  
Glass and other surfaces are  
hot during operation AND  
cool down.  
• Do not store or use gasoline or other flam-  
mable vapors and liquids in the vicinity of  
this or any other appliance.  
Hot glass will cause burns.  
Do not touch glass until it is cooled  
NEVER allow children to touch glass  
Keep children away  
CAREFULLY SUPERVISE children in same room as  
fireplace.  
• Do not overfire - If heater or chimney con-  
nector glows, you are overfiring. Overfiring  
will void your warranty.  
Alert children and adults to hazards of high  
temperatures.  
• Comply with all minimum clearances to  
combustibles as specified. Failure to  
comply may cause house fire.  
High temperatures may ignite clothing or other  
flammable materials.  
Keep clothing, furniture, draperies and other flammable  
materials away.  
WARNING  
Fire Risk.  
Installation and service of this appliance should  
be performed by qualified personnel. Hearth &  
Home Technologies recommends NFI certified  
professionals, or technicians supervised by an  
NFI certified professional.  
For use with solid wood fuel only.  
Other fuels may overfire and generate  
poisonous gases (i.e. carbon monoxide).  
Heatilator • ECO-ADV-WS22• 7057-128C • August 13, 2010  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Alert Key:  
!
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.  
WARNING! Indicates a hazardous situation which, if not avoided may result in death or serious injury.  
CAUTION! Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.  
NOTICE: Indicates practices which may cause damage to the appliance or to property.  
TABLE OF CONTENTS  
Installer’s Guide  
Congratulations ...............................................................2  
Sample of Safety/Serial Number Label ...........................2  
Warranty Policy ...............................................................4-5  
Section 6: Getting Started  
A. Design, Installation & Location  
Considerations ..................................................25  
B. Draft ..................................................................25  
C. Negative Pressure.............................................25  
D. Locating Your Appliance and Chimney.............26  
E. Chimney Termination Requirements.................26  
F. 2-10-3 Rule .......................................................27  
G. Tools and Supplies Needed..............................28  
H. Fire Safety.........................................................28  
Section 1: Listing and Code Approvals  
A. Appliance Certifications.....................................6  
B. Mobile Home Approved.....................................6  
C. Glass Specifications..........................................6  
D. BTU & Efficiency Specifications........................6  
User’s Guide  
I.  
Inspect Appliance and Components  
Section 2: Operating Instructions  
and Pre-Burn Checklist .....................................28  
A. General Operating Parts ...................................7  
B. Fire Safety.........................................................8  
C. Overfiring...........................................................8  
D. Combustible/Non-combustible Material ............8  
E. Seasoned Wood................................................8  
F. Chimney Fire.....................................................8  
G. Burning Process................................................9  
H. Burn Rate Air Control........................................10  
Section 7: Dimensions and Clearances  
A. Appliance Dimensions.......................................29  
B. Clearances to Combustibles (UL and ULC) ........30  
C. Hearth Protection Requirements.......................31  
D. Alternate Floor Protection .................................32  
Section 8: Venting and Chimney Systems  
A. Venting Systems ...............................................33  
B. Inspections........................................................33  
C. Larger Chimneys...............................................33  
D. Chimney Systems .............................................33  
E. Chimney Height/Rise and Run..........................34  
F. Factory-Built Chimney.......................................34  
G. Masonry Chimney .............................................35  
H. Masonry Chimney Liner ....................................36  
I.  
Burn Rates and Operating Efficiency................10  
J. Correct Baffle & Blanket Placement..................11  
K. Building a Fire ...................................................12  
L. Wood Fuel.........................................................13  
M. Blower Operating Instructions...........................14  
N. Clear Space ......................................................14  
O. Opacity (Smoke) ...............................................15  
P. Frequently Asked Questions.............................15  
Q. Quick Start Guide..............................................16  
I.  
Air Clearances...................................................37  
J. Thimble .............................................................37-38  
Section 3: Maintenance and Service  
A. Disposal of Ashes .............................................17  
B. Chimney & Chimney Connector  
Section 9: Appliance Set-up  
A. Outside Air Installation ......................................39  
D. Mobile Home Installation...................................40  
E. Blower Installation (Optional) ............................41  
F. Adjusting the Blower Speed Control .................41  
Inspection/Cleaning...........................................17  
C. Appliance Inspection - Routine .........................17  
D. Glass Cleaning..................................................18  
E. Firebrick Inspection & Replacement .................18  
F. Quick Reference Maintenance Guide ...............19  
Section 10: Reference Materials  
Section 4: Troubleshooting Guide.....................20  
A. Exploded Drawings ...........................................42  
B. Service Parts & Accessories.............................43-44  
C. Service & Maintenance Log ..............................45-46  
D. Homeowner’s Notes..........................................47  
E. Contact Information...........................................48  
Section 5: Service Parts Replacement  
A. Glass Replacement...........................................21  
B. Snap Disc Replacement....................................21  
C. Baffle Removal..................................................22  
D. Door Handle Assembly .....................................23  
E. Tube Channel Assembly Replacement.............24  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty Policy  
Hearth & Home Technologies Inc.  
HEATILATOR ECO-CHOICE WARRANTY  
Hearth & Home Technologies Inc., on behalf of its hearth brands (“HHT”), extends the following warranty for ECO-  
CHOICE by heatilator wood and pellet hearth appliances that are purchased from an HHT authorized dealer.  
WARRANTY COVERAGE:  
HHT warrantes to the original owner of the HHT appliance at the site of installation, and to any transferree taking own-  
ership of the appliance at the site of installation within two years following the date of original purchase, that the HHT  
appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if cov-  
ered components manufactured by HHT are found to be defective in materials or workmanship during the applicable  
warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully  
discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase  
price of the product itself. The maximum amount recoverable under this warranty is limited to the purchaser price of  
the product. This warranty is subject to conditions, exclusions and limitations as described below.  
WARRANTY PERIOD:  
Warranty coverage begins on the date of installation. In the case of new home construction, warranty coverage begins  
on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized  
HHT dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the  
date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and  
labor for covered components is produced in the following table.  
Warranty Period  
Heatilator ECO-CHOICE  
Components Covered  
Appliances  
Parts  
Labor  
Pellet  
EPA Wood  
All parts and material except as covered by  
Conditions, Exclusions, and Limitations listed  
1 year  
X
X
3 years  
X
X
Firepots and burnpots  
Castings  
3 years  
5 years  
5 years  
1 year  
X
X
X
X
3 years  
3 years  
Manifold tubes  
X
X
Firebox and heat exchanger  
All replacement parts beyond warranty period  
90 days  
See conditions, exclusions,and limitations on next page  
7014-212 2-10-10  
4
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY COVERAGE:  
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of  
HHT authorized dealers is available on th HHT branded websites.  
This warranty is only valid while the HHT appliance remains at the site of original installation.  
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact  
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service  
from a dealer other than the dealer from whom you originally purchased the product.  
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges  
for parts are not covered by this warranty.  
WARRANTY EXCLUSIONS:  
This warranty does not cover the following:  
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and  
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.  
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,  
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.  
Repair or replacment of parts that are subject to normal wear and tear during the warranty period. These parts include:  
paint, wood, pellet and coal gaskets; firebricks; grates; flame guides; and the discoloration of glass.  
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-  
plaints related to this noise are not covered by this warranty.  
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation  
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to  
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation,  
abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly  
performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly  
sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces  
or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of  
components not supplied with the appliance or any other components not expressly authorized and approved by HHT;  
(8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or  
fluctuations of electrical power supply to the appliance.  
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.  
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.  
HHT’s obligation under this warranty does not extend to the appliances’ capability to heat the desired space. Informa-  
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-  
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of  
the structure.  
This warranty is void if:  
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging  
chemicals. Overfiring can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,  
cracking and discoloration of steel or enamel finishes.  
The appliance is subjected to prolonged periods of dampness or condensation.  
There is any damage to the appliance or other components due to water or weather damage which is the result of, but  
not limited to improper chimney or venting installation.  
WARRANTY EXCLUSIONS:  
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or  
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no  
event will HHT be liable for any incidiental or consequential damages caused by defects in the appliance. Some states  
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.  
This warranty gives you specifice rights; you may also have other rights, which vary from state to state. EXCEPT TO  
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY  
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EX-  
PRESSED WARRANTY SPECIFIED ABOVE.  
7014-212 2-10-10  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listing and Code Approvals  
1
D. BTU & Efficiency Specifications  
A. Appliance Certification  
2.7 grams per hour  
82.3%  
EPA Certified:  
Efficiency:  
ECO-ADV-WS22 Wood Stove  
Model:  
Laboratory:  
Report Number:  
Type:  
Intertek  
11,700 to 27,000 per hour  
BTU Output:  
3198460  
1,580 to 2,780 sq. feet  
depending on climate zone  
Heating Capacity:  
Listed Room Heater, Solid Fuel Type  
Standard:  
UL1482 and ULC S627-00 and  
(UM) 84-HUD, Mobile Home  
Approved.  
6 inches  
Vent Size:  
2.75 cubic feet  
22 inches  
Cord Wood  
410 lbs  
Firebox Size:  
Max Wood Length:  
Fuel:  
NOTICE: This installation must conform with local  
codes. In the absence of local codes you must comply  
with the UL1482, (UM) 84-HUD and NPFA211 in the  
U.S.A. and the ULC S627-00 and CAN/CSA-B365  
Installation Codes in Canada.  
Shipping Weight:  
WARNING! Risk of Fire! Hearth & Home Technologies dis-  
claims any responsibility for, and the warranty and agency  
listing will be voided by the below actions.  
DO NOT:  
The ECO-CHOICE by Heatilator wood stove meets the U.S.  
Environmental Protection Agency’s 1990 particulate emis-  
sion standards.  
• Install or operate damaged appliance  
• Modify appliance  
• Install other than as instructed by Hearth & Home  
Technologies  
• Operate the appliance without fully assembling all  
components  
B. Mobile Home Approved  
This appliance is approved for mobile home installations  
when not installed in a sleeping room and when an out-  
side combustion air inlet is provided.  
• Overfire  
• Install any component not approved by Hearth &  
Home Technologies  
• Install parts or components not Listed or approved  
The structural integrity of the mobile home floor, ceiling,  
and walls must be maintained.  
The appliance must be properly grounded to the frame  
of the mobile home with #8 copper ground wire, and use  
only listed double-wall connector pipe.  
Improper installation, adjustment, alteration, service or  
maintenance can cause injury or property damage.  
For assistance or additional information, consult a qualified  
installer, service agency or your dealer.  
Outside Air Kit, part OAK-ACC must be installed in a mo-  
bile home installation.  
NOTE: Hearth & Home Technologies, manufacturer of  
this appliance, reserves the right to alter its products,  
their specifications and/or price without notice.  
C. Glass Specifications  
This stove is equipped with 5mm ceramic glass. Replace  
glass only with 5mm ceramic glass. Please contact your  
dealer for replacement glass.  
Heatilator is a registered trademark of Hearth & Home  
Technologies.  
6
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Guide  
Operating Instructions  
2
WARNING  
HOT SURFACES!  
Glass and other surfaces are hot during operation AND cool down.  
Hot glass will cause burns.  
DO NOT touch glass until it is cooled  
NEVER allow children to touch glass  
Keep children away  
CAREFULLY SUPERVISE children in same room as appliance.  
Alert children and adults to hazards of high temperatures.  
High temperatures may ignite clothing or other flammable materials.  
Keep clothing, furniture, draperies and other flammable materials away.  
NOTICE: If you expect that children may come into contact with this appliance, we recom-  
mend a barrier such as a decorative screen. See your dealer for suggestions.  
A. Your Wood Appliance - General Operating Parts  
WARNING! DO NOT operate appliance before reading and understanding operating instructions.  
Failure to operate appliance according to operating instructions could cause fire or injury.  
Firebrick  
Burn Rate  
Air  
Control  
Door Handle &  
Spring Handle  
Door Frame  
& Glass  
Hearth Pad  
Figure 7.1 General Operating Parts  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Combustible/Non-combustible Materials  
B. Fire Safety  
Combustible Material  
To provide reasonable fire safety, the following should be  
given serious consideration:  
Material made of or surfaced with wood, compressed  
paper, plant fibers, plastics, or any material capable  
of igniting and burning, whether flame-proofed or not,  
plastered or unplastered.  
1. Install at least one smoke detector on each floor of  
your home to ensure your safety. They should be  
located away from the heating appliance and close  
to the sleeping areas. Follow the smoke detector  
manufacturer’s placement and installation instructions,  
and be sure to maintain regularly.  
Non-combustible Material  
Material which will not ignite and burn. Such materials are  
those consisting entirely of steel, iron, brick, tile, slate,  
glass or plasters, or any combination thereof.  
2. A conveniently located Class A fire extinguisher.  
3. A practiced evacuation plan, consisting of at least two  
escape routes.  
Non-combustible Sealant Material  
4. In the event of a chimney fire:  
Sealants which will not ignite and burn: Rutland, Inc.  
Fireplace Mortar #63, Rutland 76R, Nuflex 304, GE  
RTV106 or GE RTB116 (or equivalent).  
a. Prepare occupants for immediate evacuation  
b. Notify fire department  
C. Overfiring  
E. Seasoned Wood  
WARNING! Risk of Fire!  
Burn only dry seasoned wood.  
Do not over-fire.  
Over-firing may ignite creosote or will damage the  
stove and chimney.  
To prevent over-firing your stove, DO NOT:  
• Use flammable liquids  
• Overload with wood  
Store wood under cover, out of the rain and snow.  
Dry and well-seasoned wood will not only minimize the  
chance of creosote formation, but will give you the most  
efficient fire.  
Even dry wood contains at least 15% moisture by weight,  
and should be burned hot enough to keep the chimney  
hot for as long as it takes to dry the wood out - about one  
hour.  
• Burn trash or large amounts of scrap lumber  
Permit too much air to the fire  
1. Symptoms of Over-Firing  
It is a waste of energy to burn unseasoned wood of any  
kind.  
Symptoms of over-firing may include one or more of the  
following:  
Dead wood lying on the forest floor should be considered wet,  
and requires full seasoning time.  
• Chimney connector or appliance glowing  
• Roaring, rumbling noises  
• Loud cracking or banging sounds  
• Metal warping  
Standing dead wood can be considered to be about 2/3  
seasoned.  
To tell if wood is dry enough to burn, check the ends of  
the logs.  
• Chimney fire  
If there are cracks radiating in all directions from the center,  
it is dry.  
2. What To Do if Your Stove is Over-Firing  
• Immediately close the door and air controls to reduce  
air supply to the fire.  
• If you suspect a chimney fire, call the fire department  
and evacuate your house.  
• Contact your local chimney professional and have  
your stove and stove pipe inspected for any damage.  
• Do not use your stove until the chimney professional  
informs you it is safe to do so.  
If your wood sizzles in the fire, even though the surface  
is dry, it may not be fully cured.  
F. Chimney Fire  
WARNING! Risk of Fire! A chimney fire can permanently  
damage your chimney system and nearby structures.  
In the event of a chimney fire, Hearth & Home Technolo-  
gies Inc. recommends  
Hearth & Home Technologies WILL NOT warranty stoves  
that exhibit evidence of over-firing. Evidence of over-firing  
includes, but is not limited to:  
Replacement of the chimney, and  
• Warped air tube  
• Deteriorated refractory brick retainers  
• Deteriorated baffle and other interior components  
Inspection of the adjacent structure to the provisions of  
NFPA Level III inspection criteria  
8
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Second Stage  
G. Burning Process  
In the secondary stage wood gives off flammable gases  
which burn above the fuel with bright flames.  
In recent years there has been an increasing concern about  
air quality. Much of the blame for poor air quality has been  
placed on the burning of wood for home heating.  
During this stage of burning:  
In order to improve the situation, we have developed cleaner-  
burning wood appliances that surpass the requirements for  
emissions established by our governing agencies.  
The flames must be maintained and not allowed to go  
out to ensure the cleanest possible fire.  
If the flames tend to go out, it is set too low for your  
burning conditions.  
These wood appliances must be properly operated in order  
to ensure that they perform the way they are designed to  
perform.  
The air control located at the upper right hand corner is  
used to adjust for burn rates. This is called the Burn Rate  
Air Control. Figure 10.1 on page 10.  
NOTICE: Improper operation can turn any wood appli-  
ance into a smoldering environmental hazard.  
3. Final Stage  
The final stage of burning is the charcoal stage. This occurs  
when the flammable gases have been mostly burned and  
only charcoal remains. This is a naturally clean portion of  
the burn. The coals burn with hot blue flames.  
1. Kindling or First Stage  
It helps to know a little about the actual process of burning in  
order to understand what goes on inside the appliance. The  
first stage of burning is called the kindling stage.  
It is very important to reload your appliance while  
enough lively hot coals remain in order to provide the  
amount of heat needed to dry and rekindle the next  
load of wood.  
In this stage:  
Wood is heated to a temperature high enough to evapo-  
rate the moisture present in all wood.  
It is best to open the Burn Rate Air Control before  
reloading. This livens up the coalbed and reduces  
excessive emissions (opacity/smoke). Figure 10.1 on  
page 10.  
Wood will reach the boiling point of water (212°F) and will  
not get any hotter until the water is evaporated.  
Open door slowly so that ash or smoke does not exit  
appliance through opening.  
This process takes heat from the coals and tends to cool the  
appliance.  
Break up any large chunks and distribute the coals so  
that the new wood is laid on hot coals.  
Fire requires three things to burn:  
Fuel  
Air  
Heat  
Air quality is important to all of us, and if we choose to use  
wood to heat our homes we should do so responsibly.  
We need to learn to burn in the cleanest way possible al-  
lowing us to continue using our wood appliances for many  
years to come.  
If heat is robbed from the appliance during the drying stage,  
the new load of wood has reduced the chances for a good  
clean burn.  
It is always best to burn dry, seasoned firewood. When the  
wood isn’t dry, you must open the air controls and burn at a  
high burn setting for a longer time to start it burning.  
The heat generated from the fire should be warming your  
home and establishing the flue draft, not evaporating the  
moisture out of wet, unseasoned wood, resulting in wasted  
heat.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
H. Burn Rate Air Control  
I. Burn Rates and Operating Efficiency  
The air supply enters at the upper front of the firebox,  
near the top of the glass door.  
For maximum operating efficiency  
1. Follow the instructions below for each burn rate for the  
This preheated air supplies the necessary fresh oxygen  
to mix with the unburned gases, helping to create sec-  
ond, third and fourth combustions  
Burn Rate Air Control. Figure 10.1.  
2. Burn dry, well-seasoned wood.  
This air is regulated by the Burn Rate Air Control.  
Burn Rates  
There are four settings High, Medium-High, Medium-Low  
and Low.  
1. Starting a Fire  
Open the Burn Rate Air Control by raising it all the way  
to the top for the High setting.  
When the control is raised all the way up it is on the High  
setting and when pushed all the down it is on the Low  
setting. Figure 11.1 on page 11.  
The blower tends to cool the appliance. Leave the blower  
off until the burn is well established, i.e., 30 minutes.  
After loading the appliance with wood and starting the  
fire, set the Burn Rate Air Controls to the desired setting  
by following the burn rate instructions below.  
2. High Burn Rate - Maximum Heat* - 30,000+ BTU/hr  
Raise the Burn Rate Air Control all the way up until it  
stops (top marker) to a fully open position.  
Be sure and monitor the fire closely while in this setting to  
avoid overfiring your stove.  
3. Medium-High Burn Rate* - 15,000 to 30,000 BTU/hr  
Raise the Burn Rate Air Control to the Medium High  
marker. Blower may remain on.  
4. Medium-Low Burn Rate* - 10,000 to 15,000 BTU/hr  
Raise the Burn Rate Air Control to the Medium marker.  
Leave the blower off until the burn is well established,  
i.e., 30 minutes.  
5. Low Burn Rate* - Below 10,000 BTU/hr  
Leave the Burn Rate Air Control at the bottom marker.  
Leave the blower off until the burn is well established,  
i.e., 30 minutes.  
*NOTE: These are approximate settings, and will vary with  
type of wood or chimney draft. Due to altitude and other  
environmental circumstances, this operational information is  
a guideline only.  
Figure 10.1 - Burn Rate Air Control  
10  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INCORRECT POSITIONS  
J. Correct Baffle & Blanket Placement  
WARNING! Risk of Fire!  
Firebox damage due to improper baffle placement is not  
covered by warranty. Operate the wood burning appliance  
with the baffle in the correct position only.  
Not doing so could result in:  
• Reduced efficiency  
• Overheating the chimney  
• Overheating the rear of the firebox  
• Poor performance  
Ensure correct baffle placement and replace baffle compo-  
nents if damaged or missing.  
Ceramic Blanket and Baffle Board are NOT in  
contact with the back of the firebox.  
NOTE: These are generic drawings and may not represent  
your specific model.  
CORRECT POSITION  
Back of Firebox  
Ceramic Blanket  
Ceramic Blanket is NOT in contact with the  
back of the firebox and NOT even with the Baf-  
fle Board in the front.  
Back of Firebox  
Ceramic Blanket  
Baffle Board  
Ceramic Blanket and Baffle Board MUST be in  
contact with the back of the firebox and even with  
each other in the front.  
Baffle Board  
Ceramic Blanket is bunched up at the back  
of the firebox and NOT even with the Baffle  
Board in the front.  
Figure 11.1  
Figure 11.2  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. When ready to reload, It is best to set the Burn Rate Air  
K. Building A Fire  
Control in the High position before reloading.  
WARNING! Risk of Fire! Keep combustible materials,  
gasoline and other flammable vapors and liquids clear  
of the fireplace.  
This livens up the coalbed and reduces excessive emis-  
sions (opacity/smoke).  
Open door slowly so that ash or smoke does not exit ap-  
Do NOT:  
pliance through opening.  
• Store flammable materials close to the fireplace, or  
Large logs burn slowly, holding a fire longer.  
Small logs burn fast and hot, giving quick heat.  
• Use gasoline, lantern fuel, kerosene, charcoal  
lighter fluid or similar liquids to start or “freshen up”  
a fire in this fireplace.  
10. As long as there are hot coals, repeating steps 6 through  
8 will maintain a continuous fire throughout the season.  
Keep all flammable liquids well away from the fireplace while  
it is in use. Combustible materials may ignite.  
NOTICE:  
Before lighting your first fire in the appliance:  
Build fire on brick firebox floor.  
Do NOT use grates, andirons or other methods to sup-  
port fuel as it will adversely affect emissions.  
1. Confirm the baffle and ceramic blanket are correctly  
positioned. See page 11 for detailed diagrams. They  
should be even with the front tube and resting on both  
tubes. Figure 12.1.  
2. Remove all labels from glass.  
CAUTION! Odors and vapors released during initial  
operation may be irritating to sensitive individuals.  
Open windows for air circulation.  
There are many ways to build a fire. The basic principle  
is to light easily-ignitable tinder or paper, which ignites the  
fast burning kindling, which in turn ignites the slow-burning  
firewood. Here is one method that works well:  
Baffle Boards & Blanket even with  
front tube and resting on tubes  
1. Raise the Burn Rate Air Control to the High Setting.  
2. Place several wads of crushed paper on the firebox  
floor. Heating the flue with slightly crumpled newspaper  
before adding kindling keeps smoke to a minimum.  
3. Lay small dry sticks of kindling on top of the paper.  
4. Make sure that no matches or other combustibles are in  
the immediate area of the appliance. Be sure the room  
is ventilated and the flue unobstructed.  
Burn  
Rate Air  
Control  
5. Light the paper in the appliance. NEVER light or rekindle  
fire with kerosene, gasoline, or charcoal lighter fluid; the  
results can be fatal.  
6. Once the kindling is burning quickly, add several full-  
length logs 3 to 4 inches (76 to 102mm) in diameter.  
Be careful not to smother the fire. Stack the pieces of  
wood 1/2 inch to 1 inch apart; near enough to keep each  
other hot, but far enough away from each other to allow  
air flow between them.  
Ceramic Blanket on Top  
2 pc  
Baffle  
Board  
7. Once there is an established bed of coals, set the  
Burn Rate Air Control to the desired setting following  
the instructions found in the Section: Burn Rates and  
Operating Efficiency.  
8. If you have installed the optional blower, please note that  
the blower tends to cool the appliance. Leave the blower  
off until the burn is well established, i.e., 30 minutes.  
Tube Channels  
Baffle  
CAUTION  
Protection  
Channel  
The baffle boards are FRAGILE. Use extreme caution  
when loading firewood to prevent:  
• Cracking, breaking or damaging the baffle boards  
DO NOT operate the stove without baffle boards  
Figure 12.1  
12  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Moisture  
L. Wood Fuel  
WARNING! Risk of Fire!  
WARNING  
Do NOT burn wet or green wood.  
Wet, unseasoned wood can cause accumulation of  
creosote.  
Store wood in dry location.  
Stack wood so both ends are exposed to air.  
Fire Risk.  
DO NOT BURN GARBAGE OR FLAMMABLE  
FLUIDS SUCH AS GASOLINE, NAPTHA OR  
ENGINE OIL.  
• DO NOT USE CHEMICALS OR FLUIDS TO START A  
FIRE.  
The majority of the problems appliance owners experience  
are caused by trying to burn wet, unseasoned wood.  
Do NOT burn treated wood or wood with salt (driftwood).  
May generate carbon monooxide if burn material other  
than wood.  
Wet, unseasoned wood requires energy to evaporate the  
water instead of heating your home, and  
May result in illness or possible death.  
Causes evaporating moisture which cools your chimney,  
accelerating formation of creosote.  
Seasoned Wood  
Hardwood vs Softwood  
Your appliance performance depends on the quality of the  
firewood you use.  
Cut logs to size  
Split to 6 inches (152 mm) or less in diameter.  
Air dry to a moisture content of around 20%  
Seasoned wood contains about 8,000 BTUs per pound .  
Hard woods are more dense than soft woods.  
-
-
*Soft wood - about nine months to dry  
Hard woods contain 60% more BTUs than soft woods.  
*Hard wood - about eighteen months to dry  
Hard woods require more time to season, burn slower and  
are harder to ignite.  
*NOTE: Seasoning time may vary depending on drying  
conditions.  
Soft woods require less time to dry, burn faster and are  
easier to ignite.  
Start the fire with softwood to bring the appliance up to  
operating temperature and to establish draft.  
Storing Wood  
Add hardwood for slow, even heat and longer burn time.  
Steps to ensure properly seasoned wood:  
Stack wood to allow air to circulate freely around and  
through woodpile.  
Soft woods  
Hard woods  
Elevate wood pile off ground to allow air circulation  
underneath.  
Douglas Fir  
Pine  
Spruce  
Cedar  
Oak  
Maple  
Apple  
Birch  
Poplar  
Aspen  
Alder  
Smaller pieces of wood dry faster. Any piece over 6 inches  
(152 mm) in diameter should be split.  
Wood (whole or split) should be stacked so both ends of  
each piece are exposed to air. More drying occurs through  
the cut ends than the sides.  
Store wood under cover to prevent water absorption  
from rain or snow. Avoid covering the sides and ends  
completely.  
Processed Solid Fuel Fire Logs  
NOT permitted for use in this appliance  
WARNING! Risk of Fire! DO NOT store wood:  
In front of the appliance.  
In space required for loading or ash removal.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M. Blower Operating Instructions  
NOTE: If your wood appliance is equipped with an optional  
blower, you should follow these guidelines:  
Blower  
Burn Rate  
Air Control  
Handle Up = Open  
Handle Down = Closed  
Snap Disc  
Figure 14.2 - Snap Disc Location  
7. Snap Disc Location  
If you find the blower coming on and off at undesirable  
temperatures, relocate the snap disc to another location  
in the designated zone on the back of the appliance.  
Figure 14.2. There is a manual over-ride switch to  
deactivate the snap disc, if necessary. See page 40  
for location of over-ride switch.  
Figure 14.1  
1. Initial (cold) startup: Raise the Burn Rate Air Control  
all the way up to the High setting. The blower tends to  
cool the appliance. Leave the blower off until the burn is  
well established, i.e., 30 minutes.  
N. Clear Space  
Do NOT place combustible objects within 4 ft (1.2 m) of  
the front of appliance. See Figure 14.3.  
2. High Burn Setting: Raise the Burn Rate Air Control all  
the way up to the High setting. The blower may remain  
on.  
WARNING! Do NOT place combustible objects in front  
of the appliance. High temperatures may ignite clothing,  
furniture or draperies.  
3. Medium or Medium High Burn Setting: Burn Rate Air  
Control is closed then opened to 1 inch (pull up). The  
blower may remain on.  
Mantel - avoid placing candles and other heat-sensitive  
objects on mantel or hearth. Heat may damage these  
objects.  
4. Medium Low Burn Setting: Burn Rate Air Control is  
closed then opened to 1/4 inch to 1/2 inch (pull up).  
Leave the blower off for the first 30 minutes until the burn  
is well established.  
5. Low Burn Setting: Burn Rate Air Control is closed  
(down position). Leave the blower off for the first 30 min-  
utes until the burn is well established.  
NOTE: For maximum efficiency and lowest emissions,  
when operating the blower in either the automatic or  
manual setting for the low and medium low burn settings  
leave the blower off until the burn is well established, i.e.,  
30 minutes,  
Maintain 4 ft. (1.22m) clearance to  
combustible in front of appliance  
When reloading the appliance, raise the Burn Rate Air  
Control all the wall to the High setting for 5 to 15 minutes  
before setting to the desired burn rate.  
6. The blower is equipped with a rheostat (speed control).  
The highest blower speed is obtained by turning the  
rheostat on, then adjusting back towards “OFF” as far  
as possible without turning the blower off. For a low  
blower speed, turn the control knob clockwise as far as  
possible  
Figure 14.3  
14  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
O. Opacity (Smoke)  
CAUTION! Odors and vapors released during initial  
Opacity is the measure of how cleanly your appliance is  
burning.  
operation may be irritating to sensitive individuals  
.
Open windows for air circulation.  
Opacity is measured in percent:  
100% opacity is when an object is totally obscured by  
the smoke column from a chimney, and  
0% opacity means that no smoke column can be seen.  
As you become familiar with your appliance, you should  
periodically check the opacity. This will allow you to know  
how to burn as nearly smoke-free as possible (goal of 0%  
opacity).  
P. Frequently Asked Questions  
ISSUES  
SOLUTIONS  
Odor from appliance  
When first operated, this appliance may release an odor for the first several hours. This is  
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.  
Metallic noise  
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to  
the sound produced by a furnace or heating duct. This noise does not affect the operation or  
longevity of the appliance.  
Whirring sound  
If the optional blower has been installed, the blower produces a whirring sound which  
increases in volume as the speed is increased.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Q. Quick Start Guide  
10 Pieces of Newspaper, 10-20 Pieces of Dry Kindling  
and a Few Pieces of Dry Split Wood.  
FIRST FIRE ITEMS NEEDED:  
OPEN AIR  
CONTROL  
ADD NEWSPAPER  
LOAD WOOD  
HIGH  
LOW  
3
2
1
ADD KINDLING  
WARNING! Risk of Fire  
Close and securely latch the door after  
the fire has started, and after refueling, to  
prevent:  
• Spillage of smoke, flame and carbon  
monoxide  
• Spillage of sparks, coals and logs  
• Over-firing  
DO NOT leave the stove unattended with  
the door open.  
Starting a fire may not require an open  
door for draft. The air control should 5  
LIGHT THE PAPER  
ADD MORE WOOD  
supply adequate draft.  
4
REDUCE AIR  
CONTROL  
Set to desired heat  
output  
The stove is ready for  
normal operation.  
HIGH  
LOW  
7
6
16  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance and Service  
3
Creosote - Formation and Need for Removal  
A. Disposal of Ashes  
When wood is burned slowly, it produces tar and other  
organic vapors, which combine with expelled moisture to  
form creosote.  
Frequency: When ash is within 1-3/4 inch (44mm) of  
firebox lip. Leave 1/4 to 1/2 inch (6-13mm) of ash in the  
bottom of the firebox.  
The creosote vapors condense in the relatively cool  
chimney flue of a slow-burning fire.  
By: Homeowner  
As a result, creosote residue accumulates on the flue  
lining. When ignited this creosote makes an extremely  
hot fire.  
WARNING! Risk of Fire! Ashes could contain hot embers.  
Place ashes in a metal container with a tight-fitting lid.  
The chimney and chimney connector shall be inspected  
every two months during the heating season to determine  
when a creosote buildup has occurred.  
The closed container should be placed on a non-  
combustible floor or on the ground, well away from all  
combustible materials, pending final disposal.  
When creosote has accumulated it shall be removed to  
reduce the risk of a chimney fire.  
If the ashes are disposed of by burial in soil or otherwise  
locally dispersed, they should be retained in the closed  
container until all cinders have thoroughly cooled  
C. Appliance Inspection - Routine  
B. Chimney and Chimney Connector  
Inspection/Cleaning  
Frequency: Every 2 months at the same time the chim-  
ney and chimney connector are inspected.  
By: Homeowner  
Frequency: Every 2 months during heating season or  
as recommended by a certified chimney sweep; more  
frequently if chimney exceeds or is under 14-16 ft (4.3-  
4.8m). (measured from bottom of appliance).  
Check for:  
Cracks in glass  
Door handle - smooth cam operation  
Baffle and ceramic blanket correct placement  
Baffle for cracks  
By: Certified Chimney Sweep  
WARNING! Risk of Fire! Ignited creosote is extremely HOT.  
Prevent creosote buildup.  
Firebrick for cracks, broken or crumbly  
Door gasket. (Dollar bill test). Place a dollar bill between  
the stove and the door and then shut the door. If you  
can pull the dollar bill out, remove one spacing washer  
from the door handle behind the latch cam and try the test  
again. If you can still pull the dollar bill out, replace the  
door gasket.  
Remove all ash from the firebox and extinguish all hot  
embers before disposal.  
Allow the appliance to cool completely.  
Disconnect flue pipe or remove baffle and ceramic blanket  
from appliance before cleaning chimney. Otherwise  
residue can pile up on top of the baffle and ceramic  
blanket. (See Baffle Removal on page 22).  
Glass frame for loose screws  
Close the door tightly.  
The creosote or soot should be removed with a brush  
specifically designed for the type of chimney in use.  
Clean out fallen ashes from the firebox.  
It is also recommended that before each heating season  
the entire system be professionally inspected, cleaned  
and repaired if necessary.  
WARNING! Risk of Fire!  
Do not use chimney cleaners or flame colorants in your  
appliance. It will corrode your pipe.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E. Firebrick Inspection  
D. Glass Cleaning  
Frequency: After each ash removal  
By: Homeowner  
Frequency: As desired  
By: Homeowner  
Replace the firebrick if they become, cracked, broken,  
crumbly and/or if there is a 1/4 inch (6.35mm) gap between  
the bricks.  
Clean glass with a non-abrasive glass cleaner. Abrasive  
cleaners may scratch and cause glass to crack.  
If the deposits on the glass are not very heavy, normal  
glass cleaners work well. Heavier deposits may be  
removed by using a damp cloth dipped in wood ashes or  
by using a commercially available oven cleaner.  
The firebox is lined with high quality firebrick, which has  
exceptional insulating properties. There is no need to  
use a grate; simply build a fire on the firebox floor. Do not  
operate appliance without firebrick.  
After using an oven cleaner, it is advisable to remove any  
residue with a glass cleaner or soap and water. Oven  
cleaner left on during the next firing can permanently  
stain the glass and damage the finish on plated metal  
surfaces.  
1. After the coals have completely cooled, remove all old  
brick and ash from unit and vacuum firebox.  
2. Remove new brick set from box and lay out to diagram  
shown.  
3. Lay bottom bricks in unit.  
A portion of the combustion air entering the firebox is de-  
flected down over the inside of the door glass.  
4. Install rear bricks on the top of the bottom bricks. Slide  
top of bricks under clip on back of firebox wall and  
push bottom of brick back.  
This air flow “washes” the glass, helping to keep smoke  
from adhering to its surface.  
5. Install side bricks. Slide top of brick under clips on  
side of firebox and push the bottom of the brick until  
it is flush with the side of the unit.  
When operated at a low burn rate, less air will be flowing  
over the glass and the smoky, relatively cool condition of  
a low fire will cause the glass to become coated.  
Use Part 832-0550 when ordering individual brick.  
Provide brick dimension or copy this page, mark  
the desired brick and take it to your authorized  
dealer.  
Operating the appliance with the Burn Rate Air Control  
in the High setting for 15-20 minutes should remove the  
built up coating.  
CAUTION! Handle glass assembly with care. Glass is  
breakable.  
Avoid striking, scratching or slamming glass  
Avoid abrasive cleaners  
Do not clean glass while it is hot  
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2
1
2
Figure 18.1  
No.  
Brick Size  
Qty  
20  
4
1
2
9 x 4-1/2 x 1-1/4  
9 x 2-1/4 x 1-1/4  
18  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F. Quick Reference Maintenance Guide  
Start the first inspection after the first 2 months of use,  
or if performance changes, and adjust your schedule  
accordingly. Maintenance is required for safe operation  
and must be performed to maintain your warranty.  
CAUTION! Allow the appliance to completely cool  
down before performing any cleaning or maintenance.  
Task  
Frequency  
Baffle & Blanket  
Baffle and blanket placement is critical to heat  
output, efficiency and overall life of the unit.  
Make sure the baffle is pushed all of the way to  
the back of the firebox and the blanket is laying  
flat. Inspect baffle for cracks.  
MONTHLY  
or  
Blanket  
After Every  
Cord of Wood  
Baffle  
Optional Blower  
YEARLY  
Vacuum the blower impellers.  
or  
After Every  
4 Cords of  
Wood  
Chimney System  
EVERY 2  
The chimney and chimney cap must be in-  
spected for soot and creosote ever two months  
during the burn season or more frequency if  
chimney exceeds or is under 14-16 ft (4.3m-  
4.8m) measured from bottom of appliance.  
MONTHS  
or  
After Every  
4 Cords of  
Wood  
This will prevent pipe blockage, poor draft, and  
chimney fires.  
Always burn dry wood to help prevent cap  
blockage and creosote build-up.  
Firebrick & Ash Removal  
Ashes must be cool and then you can dispose  
of the ashes in a non-combustible container.  
WEEKLY  
or  
After Every  
25 Loads of  
Wood  
Firebrick is designed to protect your firebox.  
After ashes are removed, inspect the firebrick  
and replace firebricks that are crumbling,  
cracked or broken.  
Keep door and glass gasket in good shape to  
maintain good burn times on a low burn setting.  
To test: place a dollar bill between the stove and  
door and then shut the door. If you can pull the  
dollar out, remove one washer from door handle  
behind latch cam and try again. If you can still  
pull it out, replace the door gasket.  
Door & Glass Assemblies  
WEEKLY  
or  
After Every  
25 Loads of  
Wood  
Check the glass frame for loose screws to pre-  
vent air leakage. Check glass for cracks.  
Door Handle  
WEEKLY  
Check the door latch for proper adjustment.  
This is very important especially after the door  
rope has formed to the stove face.  
Latch Cam  
or  
After Every 25  
Spacing Washers  
Check door handle for smooth cam operation.  
Loads of Wood  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
4
With proper installation, operation, and maintenance your woodstove will provide years of trouble-free service. If you do  
experience a problem, this troubleshooting guide will assist you or a qualified service person in the diagnosis of a problem  
and the corrective action to be taken.  
Start Fire Problems  
Possible Cause  
Solution  
Can not get fire started  
Excessive smoke or spillage  
Burns too slowly  
Not enough kindling/paper or no Use dry kindling, more paper. Arrange kindling &  
kindling/paper  
wood for air movement.  
Not enough heat output  
Check for restricted termination cap  
Check for blockage of outside air kit (if installed).  
Check for flue blockage.  
Pre-warm flue before starting fire (refer to Building  
a Fire Section).  
Not enough air for fire to ignite  
Check for adequate vent height (refer to Chimney  
Height Section).  
Open window below the appliance towards the  
wind.  
Wood condition is too wet, too  
large  
Use dry, seasoned wood (refer to Seasoned Wood  
Section).  
Bed of coals not established  
before adding wood  
Start with paper & kindling to establish bed of  
coals (refer to Building a Fire Section).  
Flue blockage such as birds’  
nests or leaves in termination  
cap  
Have chimney inspected for creosote and cleaned  
by a certified chimney sweep.  
Down draft or negative pressure Do not use exhaust fans during start-up (refer to  
Competition with exhaust  
Negative Pressure Section).  
devices  
Open window below the appliance towards the  
wind.  
Fire burns too fast  
Mix in hardwood.  
Mix in less seasoned wood after fire is established  
(refer to Wood Fuel Section).  
Extremely dry or soft wood  
Overdrafting  
Check for correct vent height; too much vertical  
height creates overdrafting.  
Check location of vent termination (refer to  
Chimney Termination Requirement Section).  
20  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Parts Replacement  
5
B. Snap Disc Replacement  
A. Glass Replacement  
1. Ensure that the fire is out and the appliance is cool to the  
1. Disconnect power supply. Locate the snap disc bracket  
assembly at the bottom left rear corner of the appliance.  
Figure 21.1.  
touch.  
2. Protect a table or counter top with padding or towels.  
Protect your hands and wear gloves to prevent injury.  
2. A magnet holds the bracket to the appliance. Pull the  
bracket down away from the appliance to expose the snap  
disc.  
3. Remove the door with the broken glass by lifting the door  
up and off of the hinges.  
3. Pull the snap disc and spade connectors up and out of  
4. Lay door face down on a table or counter making sure the  
handle hangs over the edge so the door lays flat, on a soft  
surface.  
bracket as shown in Figure 21.2.  
4. Using a Phillips head screw driver, remove the 2 screws  
from the snap disc and then remove the snap disc from  
the spade connectors. Replace with new snap disc and  
re-connect to spade connectors.  
5. Remove the screws from each glass retainer and remove  
the glass. (If screws are difficult to remove, soak with  
penetrating oil first).  
5. Push the snap disc and spade connectors back inside  
bracket and re-attach the bracket to the appliance.  
6. Center the glass with edges evenly overlapping the open-  
ing in the door, (i.e. same space top and bottom, left and  
right sides).  
7. Replace the glass retainers. Be careful not to cross  
thread the screws.  
8. Tighten each retainer just a few turns until each is se-  
cured. Check again for centering of glass in door frame.  
Continue to tighten each retainer alternately, a few turns at  
a time, until the glass is secure. DO NOT OVERTIGHTEN  
- can cause glass to break.  
9. Replace the door on the appliance.  
Snap Disc Location  
WARNING! Risk of Fire or Injury!  
Use only glass that is specified in the manual, DO NOT  
replace with any other material. Glass breakage will occur.  
Figure 21.1  
CAUTION!  
Handle glass with care.  
• Inspect the gasket to ensure it is undamaged.  
• Do NOT strike, slam or scratch glass.  
• Do NOT operate appliance with glass & door assembly  
removed.  
Snap Disc  
• Do NOT operate with glass cracked, broken or  
scratched.  
This appliance is equipped with ceramic super heat-resistant  
glass, which can only be broken by impact or misuse.  
Magnet  
Spade  
Connectors  
Figure 21.2  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Baffle Removal  
Baffle Boards & Blanket even with  
front tube and resting on tubes  
1. Remove all ash from the firebox, and extinguish all hot  
embers before disposal into a metal container.  
2. Remove the baffle protection channel by rotating it down  
from the front tube. Figure 22.2.  
3. The baffle board has 2 pieces. With the ceramic blanket  
still in place, slide one baffle piece over the top of other  
one and pull out top piece through the door opening and  
then remove bottom baffle piece. Figure 22.1.  
Burn  
Rate Air  
Control  
4. Remove the ceramic blanket.  
5. Re-install the ceramic blanket and smooth out the blan-  
ket.  
6. Slide the baffle pieces one piece at a time underneath the  
blanket. Be sure the baffle boards are even with the front  
manifold tube and is resting on all tubes. Figure 22.1 and  
22.2.  
Ceramic Blanket on Top  
2 pc  
Baffle  
Board  
7. Re-install the baffle protection channel by rotating it up and  
around the front tube so the bottom flange of the channel  
rests behind the manifold tube. The baffle boards and  
blanket are tucked inside the rear of the baffle protection  
channel.  
Tube Channels  
Baffle  
Protection  
Channel  
Figure 22.2  
Figure 22.1 - Baffle  
22  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Door Handle Assembly  
1. Install washer on door handle shaft.  
2. Slide door handle through door.  
3. Install second washer(s) as shown in Figure 23.1.  
4. Install key in groove.  
5. Align groove in latch cam with key; slide latch cam over  
shaft  
6. Install locknut but do not overtighten, the handle needs  
to move smoothly.  
7. Install spring handle turning in a counter-clockwise mo-  
tion to desired location on door handle rod.  
CAUTION! Do not overtighten lock nut. The door handle  
needs to move smoothly.  
Door Cross Section  
(example)  
Latch Cam  
Locknut  
Spring  
Handle  
Door Handle  
Spacing  
Washers  
Square Key  
Figure 23.1  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E. Tube Channel Assembly Replacement  
NOTE: Service Space  
Removing Tube Channel Assembly  
In order to replace the tube channel assembly a clear-  
ance of 19 inches (483mm) is required on the right side  
of stove in order to remove the tubes with the stove in  
place.  
1. Remove the baffle protection channel, ceramic blanket  
and the 2 baffle boards. See instructions on page 22.  
2. Remove the right side shield by removing 3 screws in the  
back using a Phillips head screw driver.  
If space is not available, the stove will have to be dis-  
connected from the chimney to proceed with the tube  
replacement.  
3. Remove 4 screws from channel access cover and remove  
cover.  
4. Locate 2 channel bolts behind the channel access cover  
and remove using a 7/16 socket wrench. Slide out tube  
channel assembly.  
NOTE:Soak the bolts with penetrating oil for at least 15 min-  
utes before trying to remove them.  
Replacing Tube Channel Assembly  
1. Slide the tube channel assembly into side of firebox and  
insert each tube into the corresponding hole in the tube  
channel rack starting with the back hole first.  
2. Make sure tube channel assembly is flush against the  
side of the stove and secure with channel nuts.  
3. Re-install channel cover and side shield.  
4. Re-install ceramic blanket, baffle pieces and baffle pro-  
tection channel. See instructions of page 22.  
Tube Channel Rack  
Channel Access  
Cover  
Channel  
Cover  
Screws (4)  
Remove 3  
Screws  
Tube  
Channel  
Assembly  
Channel Bolts (2)  
Side Panel  
Figure 24.1  
24  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installer’s Guide  
Getting Started  
6
A
. Design and Installation Considerations  
C. Negative Pressure  
NOTICE: Check building codes prior to installation.  
WARNING! Risk of Asphyxiation! Negative pressure can  
cause spillage of combustion fumes and soot. Fire must draft  
properly for safe operation.  
Installation MUST comply with local, regional, state and  
national codes and regulations.  
Consult insurance carrier, local building inspector, fire  
officials or authorities having jurisdiction over restrictions,  
installation inspection and permits.  
Negative pressure results from the imbalance of air avail-  
able for the fireplace to operate properly. It can be stron-  
gest in lower levels of the house.  
Before installing, determine the following:  
Causes include:  
Type of chimney connector to be used  
- Single wall, vertical or horizontal  
Exhaust fans (kitchen, bath, etc.)  
Range hoods  
Combustion air requirements for furnaces, water heaters  
and other combustion appliances  
Clothes dryers  
Location of return-air vents to furnace or air conditioning  
Imbalances of the HVAC air handling system  
Upper level air leaks such as:  
- Recessed lighting  
- Double wall, vertical or horizontal  
Consult page 30 for clearances to combustibles  
Power outlet located close by for optional blower  
B. Draft  
Draft is the pressure difference needed to vent appliances  
successfully. When a appliance is drafting successfully, all  
combustion byproducts are exiting the home through the  
chimney.  
- Attic hatch  
- Duct leaks  
To minimize the effects of negative air pressure:  
Considerations for successful draft include:  
Install the outside air kit with the intake facing prevailing  
winds during the heating season  
Ensure adequate outdoor air for all combustion appliances  
and exhaust equipment  
Ensure furnace and air conditioning return vents are not  
located in the immediate vicinity of the fireplace  
Avoid installing the fireplace near doors, walkways or small  
isolated spaces  
Recessed lighting should be a “sealed can” design  
Attic hatches weather stripped or sealed  
Attic mounted duct work and air handler joints and seams  
taped or sealed  
Preventing negative pressure  
Location of appliance and chimney  
o be sure that your appliance burns properly:  
T
During a low burn, the chimney draft (static pressure) should  
be approximately -.04 inch water column (W.C.)  
During a high burn the chimney draft should be approximately  
-.10 inch (W.C.)  
Measure the W.C at 6 inches (152mm) above the top of the  
appliance after one hour of operation at each burn setting.  
NOTICE: Hearth & Home Technologies assumes no  
responsibility for the improper performance of the appliance  
system caused by:  
Basement installations should be avoided  
Inadequate draft due to environmental conditions  
Downdrafts  
Tight sealing construction of the structure  
Mechanical exhausting devices  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Locating Your Stove & Chimney  
Consider the appliance location in order to avoid  
floor and ceiling attic joists and rafters.  
Location of the appliance and chimney will affect perfor-  
mance. As shown in Figure 26.1 the chimney should:  
Locate termination cap away from trees, adjacent  
structures, uneven roof lines and other obstruc-  
tions.  
Install through the warm space enclosed by the build-  
ing envelope. This helps to produce more draft, espe-  
cially during lighting and die down of the fire.  
Your local dealer is the expert in your geographic area and  
can usually make suggestions or discover solutions that will  
easily correct any flue problems you may encountered.  
Penetrate the highest part of the roof. This minimizes  
the affects of wind turbulence and down drafts.  
Recommended Location:  
• Above peak  
• Inside heated space  
Recommended Location:  
• Above peak  
Marginal Location:  
Wind loading possible  
Marginal Location:  
• Below peak  
Location NOT recommended:  
• Not the highest point of the roof  
• Wind loading possible  
Location NOT recommended:  
Too close to tree  
• Below adjacent structure  
• Lower roof line  
• Avoid outside wall  
Recommended:  
• Insulated exterior chase  
in cooler climates  
Windward  
Leeward  
Multi-level Roofs  
Recommended:  
Outside Air Intake  
on windward side  
NOT recommended:  
Outside Air Intake  
on leeward side  
Figure 26.1  
E. Chimney Termination Requirements  
NOTICE: Locating the appliance in a basement or in a location  
of considerable air movement can cause intermittent smoke  
spillage from appliance. Do not locate appliance near  
Follow manufacturer’s instructions for clearance, secur-  
ing flashing and terminating the chimney.  
Frequently open doors  
Must have an approved and Listed cap  
Central heat outlets or returns  
Must not be located where it will become plugged  
by snow or other material  
Must terminate at least 3 feet (91cm) above the  
roof and at least 2 feet (61cm) above any portion  
of the roof within 10 feet (305cm).  
NOTICE:  
Chimney performance may vary.  
Trees, buildings, roof lines and wind conditions affect  
performance.  
Must be located away from trees or other struc-  
tures  
Chimney height may need adjustment if smoking or  
overdraft occurs.  
26  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F. 2-10-3 Rule  
These are safety requirements and are not meant to assure proper flue draft.  
Less than 10 ft. (305cm)  
2 ft. (61cm)  
3 ft. (91cm)  
Minimum  
2 ft. (61cm)  
10 ft. (305cm) To Nearest Roofline  
3 ft. (91cm)  
Minimum  
Pitched Roof  
Figure 27.1  
10 ft. (305cm) or more  
Less than 10 ft. (305cm)  
Wall or Parapet  
2 ft. (61cm) Minimum  
3 ft. (91cm) Minimum  
3 ft. (91cm) Minimum  
Flat Roof  
Figure 27.2  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
G. Tools And Supplies Needed  
Pre-Burn Check List  
Before beginning the installation be sure the following tools  
and building supplies are available:  
1.  
2.  
Place the appliance in a location near the final  
installation area and follow the procedures below:  
Reciprocating saw  
Pliers  
Framing material  
High temp caulking material  
Gloves  
Open the appliance and remove all the parts and  
articles packed inside the Component Pack. Inspect  
all the parts and glass for shipping damage. Contact  
your dealer if any irregularities are noticed.  
Hammer  
Phillips screwdrive  
Flat blade screwdriver  
Plumb line  
Framing square  
Electric drill and bits  
Safety glasses  
3.  
4.  
5.  
6.  
All safety warnings have been read and followed.  
This Owner’s Manual has been read.  
Floor protection requirements have been met.  
Venting is properly installed per venting manufactur-  
ing instructions.  
Level  
Tape measure  
7.  
8.  
The proper clearances from the appliance and chim-  
ney to combustible materials have been met.  
1/2-3/4 in. length, #6 or  
#8 self-drilling screws  
Misc screws and nails  
The masonry chimney is inspected by a professional  
and is clean, or the factory built metal chimney is  
installed according to the manufacturer’s instruc-  
tions and clearances.  
H. Fire Safety  
To provide reasonable fire safety, the following should be  
given serious consideration:  
9.  
The chimney meets the required minimum height.  
10.  
All labels have been removed from the glass  
1. Install at least one smoke detector on each floor of  
your home to ensure your safety. They should be  
located away from the heating appliance and close  
to the sleeping areas. Follow the smoke detector  
manufacturer’s placement and installation instructions,  
and be sure to maintain regularly.  
door  
.
11.  
12.  
Plated surfaces have been wiped clean, if appli-  
cable.  
A power outlet is available nearby if installing  
optional blower assembly.  
2. A conveniently located Class A fire extinguisher  
to contend with small fires resulting from burning  
embers.  
I. Inspect Appliance and Components  
Remove appliance and components from packaging and  
inspect for damage.  
Doors are shipped in separate packages.  
Report to your dealer any parts damaged in shipment.  
Read all the instructions before starting the  
installation. Follow these instructions carefully  
during the installation to ensure maximum safety and  
benefit.  
WARNING! Risk of Fire!  
Inspect appliance and components for damage.  
Damaged parts may impair safe operation.  
• Do NOT install damaged components.  
• Do NOT install incomplete components.  
• Do NOT install substitute components.  
Report damaged parts to dealer.  
28  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions and Clearances  
7
A. Appliance Dimensions  
NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)  
19-1/16 in.  
(484mm)  
26 in. (660mm)  
13 in.  
(330mm)  
9-13/16 in.  
(249mm)  
C
L
14-13/16 in.  
(376mm)  
13-13/16 in.  
(351mm)  
9-9/16 in.  
(243mm)  
34 in.  
(864mm)  
19-5/8 in. (499mm)  
21-11/16 in. (551mm)  
Figure 29.1 - Front View  
Figure 29.2 -Top View  
30-3/4 in. (781mm)  
28-3/8 in. (720mm)  
15-1/8 in.  
(384mm)  
6-5/8 in.  
(168mm)  
C
L
27-1/2 in. (699mm)  
11-5/8 in.  
(295mm)  
23-1/4 in. (591mm)  
27 in. (686mm)  
Figure 29.3 - Side View  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Clearances to Combustibles (UL and ULC)  
NOTE: Clearances may only be reduced by means  
approved by the regulatory authority having jurisdiction  
BACKWALL / SIDEWALL  
ALCOVE SIDE VIEW  
A
B
G
A
C
H
90° OFF TOP  
D
G
UP & OUT CEILING  
B
CLEARANCE  
STOVE TO CEILING  
CLEARANCE  
CORNER INSTALLATION  
ALCOVE TOP VIEW  
E
F
C
E
D
F
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: Inches & (Millimeters)  
NOTE: All “A”, “C” and “F” dimensions are to inside diameter of flue collar.  
A
B
C
D
E
F
G
H
INSTALLATION: Full Vertical OR Horizontal with 2 foot (609mm) minimum vertical Off Stove Top  
SINGLE WALL PIPE  
DOUBLE WALL PIPE  
10 (254) 8.25 (210) 21 (533) 11 (279) 3.5 (89)12.5 (318) 49 (1245)  
*
9 (229) 7 (178) 19.5 (495) 9 (229) 3 (76) 12 (305) 49 (1245) 10 (254)  
INSTALLATION: 90o ELBOW OFF TOP OF STOVE THROUGH BACKWALL  
SINGLE WALL PIPE  
DOUBLE WALL PIPE  
9.25 (235) 7.5 (191) 18 (457)  
9.25 (235) 7.5 (191) 18 (457)  
8 (203) 3.5 (89)12.5 (318) 49 (1245)  
*
8 (203) 3 (76) 12 (305) 49 (1245) 10 (254)  
INSTALLATION: ALCOVE Six inch (6") (152mm) diameter listed Single Wall or Double Wall air  
insulated connector pipe with UL103 HT** Listed factory-built Class "A" chimney, or a masonry  
chimney. (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove shall be  
no more than 48 inches (1219mm) with a minimum height of 84 inches (2133mm) from floor to  
bottom of ceiling and the referenced clearances.  
**In Canada must comply with Standard CAN/ULC-S629-M87 for the 650oC Factory-built chimney.  
* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED  
NOTE: Service Space  
WARNING! Risk of Fire!  
In order to replace the tube channel assembly a clearance  
of 19 inches (483mm) is required on the right side of stove  
in order to remove the tubes with the stove in place.  
• Comply with all minimum clearanes to combustibles  
as specified.  
• Failure to comply may cause house fire.  
If space is not available, the stove will have to be discon-  
nected from the chimney to proceed with the tube replace-  
ment.  
30  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In Canada, similar floor protection must be provided 18  
inches (457mm) in front and 8 inches (203mm) from the  
sides and rear of the appliance. *See exception.  
C. Hearth Protection Requirements  
FLOOR PROTECTION:  
Must be non-combustible material.  
Extend beneath heater and to the front, sides and rear as  
indicated.  
The floor must be non-combustible or otherwise  
adequately protected from radiant heat given off by the  
unit and from sparks and falling embers.  
A layer of thin brick or ceramic tile over a combustible  
floor is NOT sufficient.  
*ExCEPTION: Non-combustible floor protections must  
extend beneath the flue pipe when installed with horizontal  
venting and extend 2 inches (51mm) beyond each side.  
See Figure 31.4.  
WARNING! Risk of Fire!  
• Hearth pads must be installed exactly as specified.  
In US installations, it is necessary to install a floor protector  
of a minimum of 1/4 inch (6.35mm), k value = 1.95 and R value  
= 0.13 of non-combustilbe material a minimum of 16 inches  
(406mm) in front of glass and 8 inches (203mm) to both  
sides of the fuel loading door. Open the door and measure  
8 inches (203mm) from the side edge of the opening in the  
face of the appliance. *See exception.  
• High temperatures or hot embers may ignite concealed  
combustibles.  
Double-Wall Pipe  
Required for  
Hearth Pad Size  
51-1/16 in.  
(297mm)  
Optional  
Coverage  
43-3/16 in.  
(1097mm)  
Optional  
Optional  
43-1/2 in.  
minimum  
Coverage  
Coverage  
Fuel loading door  
8 in.  
135o  
8 in.  
Required-  
Coverage  
31-11/16 in.  
(805mm)  
16 in. from glass  
3 in.  
27-3/8 in. (696mm)  
(76mm)  
31-5/8 in.  
minimum  
USA  
USA  
Figure 31.2  
Figure 31.1  
USA required  
203mm (8 in.)  
Canada recommended  
203mm  
(8 in.)  
203mm  
(8 in.)  
1359mm  
(53-1/2 in.)  
minimum  
457mm (18 in.)  
Must extend 2 in. (51mm) beyond  
each side of pipe (shaded area)  
1066mm (42 in.)  
minimum  
CANADA  
Figure 31.3  
Figure 31.4  
Illustrations and photos reflect typical installations and are FOR DESIGN PURPOSES ONLY.  
Illustrations/diagrams are not drawn to scale.  
Actual installation may vary due to individual design preference  
Hearth & Home Technologies reserves the right to alter its products.  
NOTICE:  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Calculating Alternate Floor Protection Material  
Thermal Conductivity: k value  
The k value indicates the amount of heat (in BTU’s) that will flow  
in 1 hour throught 1 square foot of a uniform material 1 inch thick  
for each degree (F) of temperature difference from one side of  
the material to the other. The LOWER the k factor means less  
heat is being conducted through the non-combustible material to  
the combustible material beneath it. The k value of a material  
must be equal or smaller then the required k value to be accept-  
able.  
(BTU) (inch)  
(foot2 (hour) (oF)  
Thermal Resistance: R value  
The R value is a measure of a material’s resisteance to heat  
transfer. R value is convenient when more than one material is  
used since you can add the R values together, whereas you can  
not do this for k value. The HIGHER the R factor means less  
heat is being conducted through the non-combustible material to  
the combustible material beneath it. The R value of a material  
must be equal or larger then the required R value to be accept-  
able.  
Converting k to R:  
Divide 1 by k and multiply the results times th thickness in inches  
of the material.  
R = 1/k x inches of thickness  
Converting R to k:  
Divide the inches of thickness by R.  
k = inches of thickness/R  
Calculatons:  
Example: Floor protection requires k value of .84, 3/4 inch thick.  
Alternative material has a k value of .6 and is 3/4 inch thick.  
Divide .6 by .75 = k value of .80. This k value is smaller than .84  
and therefore is acceptable.  
32  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Venting and Chimney Systems  
8
D. Chimney Systems  
A. Venting Systems  
The chimney connector joins the stove to the chimney.  
Chimney Connector:  
It must be a 6 inch (152mm) minimum diameter 24 gauge  
mild steel black.  
It is also known as flue pipe or stove pipe. It must be  
6 inches (152mm) minimum diameter stainless steel  
connector pipe.  
Or an approved air-insulated double wall venting pipe.  
Single wall connector or stove pipe  
Chimney:  
Must be at least 24 gauge mild steel.  
The chimney can be new or existing, masonry or  
prefabricated and must meet the following minimum  
requirements as specified below.  
Sections must be attached to the appliance and to each  
other with the crimped (male) end pointing toward the  
stove.  
Thimble:  
All joints, including the connection at the flue collar, should  
be secured with 3 sheet metal screws or rivets as per pipe  
manufacturer’s instructions..  
A thimble is a manufactured or site-constructed device  
installed in combustible walls through which the chimney  
connector passes to the chimney.  
Follow the minimum clearances to combustibles  
It is intended to keep the walls from igniting.  
Site constructed thimbles must meet NFPA 211  
Standards.  
Factory-built chimney connector (vented)  
A Listed connector (vented) must be used when installing  
this unit in a mobile home.  
Factory-built must be suitable for use with selected  
chimney and meet UL103 Type HT Standards.  
Follow instructions provided by the manufacturer for  
manufactured thimbles for masonry chimney and factory-  
built chimneys.  
The Listed connectors must conform to each other to  
ensure a proper fit and seal.  
WARNING! Risk of Fire!  
Follow venting manufacturer’s clearances and instructions  
when installing venting system.  
Crimped  
Flue Gas  
End  
B. Inspections  
Direction  
Toward  
Stove  
Existing chimneys should be inspected and cleaned by a  
qualified professional prior to installation. The chimney  
must not have cracks, loose mortar or other signs of dete-  
rioration and blockage. Hearth & Home recommends a  
NFI or CSIA certified professional or a technician, under  
the direction of a certified professional, conduct a Level II  
inspection per NFPA 211.  
Secure pipe sections with a  
minimum of 3 screws  
Figure 33.1 Chimney Connector  
WARNING! Risk of Fire!  
C. Larger Chimneys  
Follow chimney connector manufacturer’s instructions for proper  
installation.  
It is recommended that chimneys with larger diameters  
than 6 inches (152mm) be relined. An oversized flue  
can affect draft and impair performance and will allow  
increased build-up of creosote.  
ONLY use connector:  
Within the room, between appliance and ceiling or wall.  
Connector shall NOT pass through:  
Attic or roof space  
Closet or similar concealed space  
Floor or ceiling  
NOTICE: Check with your local building authorities  
and/or consult the National Fire Protection Association  
(NFPA 211).  
Maintain minimum clearances to combustibles  
NOTICE: Where passage through the wall, or partition  
of combustible construction is desired in Canada, the  
installation shall conform to CAN/CSA-B365.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listed Termination Cap  
Roof Brace (if required)  
E. Chimney Height / Rise and Run  
• This product was designed for and tested on a 6 inch  
(152mm) chimney, 14 to 16 feet (427-487cm) high, (in-  
cludes appliance height) measured from the base of the  
appliance.  
Storm Collar  
Flashing  
• The further your stack height or diameter varies from this  
configuration, the possibility of performance problems  
exists.  
• Chimney height may need to be increased by 2 - 3% per  
each 1000 feet (304.8m) above sea level.  
Trim Collar on  
Inside Wall  
Listed Chimney  
Insulated " T "  
• It is not recommended to use offsets or elbows at altitudes  
above 4000 feet (1219.2m) above sea level or when there  
are other factors that affect flue draft.  
Chimney  
Connector  
Wall Support  
F. Factory-Built Chimney  
The chimney can be new or existing, and must meet the  
following minimum requirements.  
Floor  
Protector  
Must be a minimum 6 inch (152mm) diameter (ID) high  
temperature chimney listed to UL 103 HT (2100 F) or  
o
ULC S629M.  
Must use components required by the manufacturer  
for installation.  
Figure 34.1 - Factory-Built Exterior Chimney  
Must maintain clearances required by the manufacturer  
for installation.  
Listed Termination Cap  
Storm Collar  
Refer to manufacturers instructions for installation.  
Flashing  
NOTICE: In Canada when using a factory-built chim-  
o
ney it must be safety listed, Type UL103 HT (2100 F)  
o
[1149 C] CLASS “A” or conforming to CAN/ULC-  
o
S629M, STANDARD FOR 650 C FACTORY-BUILT  
CHIMNEYS.  
Listed Chimney  
Ceiling Support  
WARNING! Risk of Fire!  
Inspection of Chimney:  
Chimney must be in good condition and meets the  
minimum standard of NFPA 211.  
Factory-built chimney must be 6 inches (152mm)  
UL103 HT.  
Chimney  
Connector  
WARNING! Risk of Asphyxiation!  
DO NOT CONNECT THIS APPLIANCE TO  
A CHIMNEY FLUE SERVICING ANOTHER  
APPLIANCE OR TO ANY AIR DISTRIBUTION  
DUCT OR SYSTEM.  
Floor  
Protector  
This may allow flue gases to enter the house.  
Figure 34.2 - Factory-Built Interior Chimney  
34  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
G. Masonry Chimney:  
Spark Arrestor Cap  
Concrete Cap  
Fireclay Flue Liner  
With Air Space  
Rafter  
Flashing  
Eave  
1 in. (25mm) Clearance  
With Firestop  
Ceiling Joist  
Combustible Wall  
Thimble,  
12 in. (305mm)  
Of Brick  
Sheathing  
Outside Air Rear Vent  
Outside Air  
Termination Cap  
Floor  
Protector  
Airtight  
Cleanout Door  
Figure 35.1 Masonry Chimney  
WARNING! Risk of Fire!  
Inspection of Chimney:  
WARNING! Risk of Asphyxiation!  
DO NOT CONNECT THIS APPLIANCE TO A  
CHIMNEY FLUE SERVICING ANOTHER APPLIANCE  
OR TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.  
Chimney must be in good condition and meets the  
minimum standard of NFPA 211.  
This may allow flue gases to enter the house.  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H. Masonry Chimney Liner  
Wood Stud 2 in.  
(51mm)  
Clearance from  
chimney wall  
For optimal performance, masonry chimneys used to vent  
this appliance should be:  
Fireclay liner 5/8 in.  
(16mm) Minimum  
or Equivalent.  
1. Lined with a 6 inch (152mm) stainless steel liner.  
Installations into a clay flue without a stainless steel  
liner may reduce draw which affects performance,  
cause the glass to darken and produce excessive  
creosote.  
Header  
2. It is recommended that a chimney with a larger diameter  
than 6 inches (152mm) be relined.  
The oversized flue can cause poor performance and  
contribute to the accumulation of creosote.  
3. Have the chimney cleaned before the stove is installed  
and operated.  
Fireclay liner 5/8 in.  
(16mm) Minimum  
or Equivalent.  
The following bullets list the more critical requirements for a  
properly constructed chimney:  
The masonry wall of the chimney, if brick or modular  
block, must be a minimum of 4 inches (102mm) nominal  
thickness.  
Sill support  
A chimney of rubble stone must be at least 12 inches  
(305mm) thick.  
Thimble Assembly:  
The chimney must have a fire clay flue liner (or equivalent)  
with a minimum thickness of 5/8 inch (16mm) and must  
be installed with refractory mortar.  
12 in. (305mm) of  
brick separation  
between clay liner  
and combustibles.  
An equivalent liner must be a listed chimney liner system  
or other approved material.  
Figure 36.1  
Since an oversized flue contributes to the accumulation  
of creosote, the size of the flue should be checked to  
determine that it is not too large for the appliance.  
The chimney should also be checked to ensure it meets  
the minimum standard of the National Fire Protection  
Association (NFPA) Standard 211.  
A chimney support package must be used when a  
connection is made through the ceiling to a factory built  
chimney.  
An approved thimble and chimney support package are  
absolutely necessary to provide safe clearances to  
combustible wall and ceiling material.  
NOTICE: In Canada, the installation shall conform to  
CAN/CSA-B365.  
NOTICE: Check with your local building authorities  
and/or consult the National Fire Protection Association  
(NFPA 211).  
36  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I. Air Clearances  
C
L
• Masonry chimney clearance must meet NFPA 211 mini-  
mum requirement of 2 inches (51mm) to sheet metal  
supports and combustibles.  
ceiling  
13.5” below ceiling to top  
of opening  
Wall  
or top of opening is a min.of  
4.5” below min.clearance  
specified by connector mfg.  
• Minimum of 1 inch (25mm) clearance around the chim-  
ney connector.  
Minimum18.0”  
NFPA 211  
1.5 2x2 framing stud  
2.0 min air clearance  
1.0 min air clearance  
4.5  
Top of wall opening is a minimum of 13-1/2 inches  
(343mm) from ceiling or 4-1/2 inches (114mm) below  
minimum clearance specified by chimney connector  
manufacturer. NFPA 211 minimum vertical clearance of  
18 inches (457mm) from chimney connector and ceiling  
or minimum recommended by chimney connector manu-  
facturer. Figure 37.1.  
1.5”  
2.0”  
1.0”  
17.0” OD  
14.0” ID  
8.0”  
C
L
1.0”  
2.0”  
1.5”  
Center of Hole  
Thimble  
J. Thimble  
Site constructed for masonry chimney installation:  
Components  
Include depth  
of hearth pad  
• A minimum length of 12 inches [305mm] (longer for  
thicker walls) of solid insulated factory-built chimney  
length constructed to UL 103 Type HT 6 inch (152mm)  
inside diameter. Chimney needs to extend a minimum of  
2 inches (51mm) from the interior wall and a minimum of  
1 inch (25mm) from the exterior wall.  
• Wall spacer, trim collar and wall band to fit solid pack  
chimney selected.  
Figure 37.1 - Thimble Construction  
• Minimum 8 inch (203mm) diameter clay liner section (if  
not already present in chimney) and refractory mortar.  
Instructions:  
Solid Pack Chimney with Metal Supports  
as a Thimble  
1. Open inside wall at proper height for the chimney con-  
nector to enter the masonry chimney. Figure 37.1.  
2. Entry hole to masonry chimney must be lined with an 8  
inch (203mm) minimum diameter clay liner, or equiva-  
lent, secured with refractory mortar.  
Fire Clay Flue  
Liner  
with Airspace  
3. Construct a 17 inch x 17 inch (432mm x 432mm) outside  
dimension frame from 2 x 2 framing lumber to fit into wall  
opening. Inside opening of frame should be no less than  
14 inch x 14 inch (356mm x 356mm). Figure 37.1.  
Masonry  
Chimney  
Trim Collar  
4. Attach the wall spacer to the chimney side of the frame.  
Wall Spacer  
Chimney Section  
with 2 inch  
(51mm)  
Clearance to  
Combustibles  
5. Nail the frame into the wall opening. The spacer should  
be on the chimney side.  
Wall Band to  
Secure Chimney  
Section  
6. Insert the section of the solid insulated chimney into the  
outer wall of the masonry chimney.  
Chimney  
Connector  
Wood Studs Used  
for Framing - Spaced  
2 inch (51mm)  
7. Tightly secure the length of the solid insulated chimney  
with the wall band to the masonry chimney.  
clearance from  
Masonry Chimney  
8. Insert a section of chimney connector into the chimney.  
Make sure it does not protrude past the edge of the clay  
chimney liner inside the chimney.  
9. Seal the end of the chimney connector to the clay liner  
with refractory mortar.  
Figure 37.2  
10. Install trim collar around the sold pack chimney section  
.
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Solid Pack Chimney with Metal Supports  
as a Thimble (Cont’d)  
Min. Chimney Clearance to  
Wall Spacer and  
Combustibles - 2 inch (51mm)  
Min. Clearance  
2 inch (51mm)  
1 inch (25mm) Air  
Space to Chimney  
Section  
Chimney Flue  
Liner  
Fireclay  
Liner or  
Equivalent  
Chimney  
Connector  
Chimney Section  
Trim Collar  
Wall Band  
Wall Spacer  
Masonry Chimney  
Constructed to NFPA 211  
Figure 38.1  
WARNING! Risk of Fire!  
Do NOT pack insulation or other combustibles between  
spacers.  
ALWAYS maintain specified clearanes around  
venting and spacers and install spacers as specified.  
Failure to keep insulation or other material away from  
vent pipe may cause a fire.  
38  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appliance Set-up  
9
A. Outside Air Kit Installation  
5. Floor Installation Alternative: In some instances  
you may not be able to install the flex pipe as show in  
Figure 39.1.  
A source of air (oxygen) is necessary in order for combustion to  
take place. Whatever combustion air is consumed by the fire  
must be replaced.  
If that is the case, follow the instructions for a rear  
installation install the flex pipe to the rear of the ped-  
estal and remove the circular “Knock-Out” in the base  
of the the pedestal. You must seal off the pedestal  
with non-combustible material (not supplied). The  
goal is to seal the pedestal so no room air can leak  
into the pedestal and to seal for cold air infiltration.  
Figure 39.2.  
Air is replaced via air leakage around windows and under  
doors. In homes that have tightly sealed doors and windows,  
an outside air source is highly recommended. An optional Out-  
side Air Kit is available.  
Included in kit: Termination cap, (2) wire ties, flex adapter,  
and fasteners  
Items Needed for Installation (not supplied)  
• 4 inch flex aluminum pipe, or if using alternate material,  
then it shall be made from durable, non-combustible, heat  
o
resistant material up to 350oF (177 C). Cut the pipe to the  
required length for your installation.  
• Phillips head screw driver  
• Silicone sealant  
• Non-combustible pedestal sealing material if installing with  
the Alternate Floor configuration.  
• Drills and saws necessary for cutting holes through the wall  
or flooring in your home  
Instructions  
1. Rear: Remove the access cover on the back of the pedestal  
and discard. Figure 39.2.  
Sealing Material  
(not supplied)  
2. Using a #2 Phillips screw driver attach the flex adapter to  
the appliance using 4 screws. Secure with wire tie. Figure  
39.1.  
Remove Circular “Knock-Out” in Base of  
Pedestal and Seal the Pedestal with Non-  
combustible Material.  
3. Floor: For standard floor installation remove the circular  
“knock-out” in the base of the pedestal.  
4. Floor & Rear Installation: Cut a 4 inch (102mm) hole in out-  
side wall or floor to accommodate outside air piping. Use 4 inch  
(102mm) aluminum metal flex or rigid piping to directly connect  
outside air to appliance intake. Use the supplied termination  
cap with a rodent screen. Seal between the wall (or floor) and  
the pipe with silicone to prevent moisture penetration.  
Figure 39.2 - Alternate Floor Installation  
WARNING! Risk of Fire and Asphyxiation!  
Do not draw outside combustion air from:  
Wall, floor, ceiling cavity or enclosed space such  
as an attic or garage. Also do not draw outside air  
from close proximity to exhaust vents or chimneys.  
Fumes or odor may result if you do.  
Flex Adapter  
Wire Tie  
Wire Tie  
Outside air inlet must be located to prevent blockage  
from leaves, snow, ice or other debrs. Blockage may  
cause combustion air starvation. Smoke spillage may  
set off alarms or irritate sensitive individuals.  
Termination  
Cap  
The length of the outside air supply duct shall NOT  
exeed the length of the vertical height of the exhaust  
flue.  
For Floor Installa-  
tions Remove  
Circular “Knock-Out”  
in Base of Pedestal.  
The fire will not burn properly and their will be  
smoke spillage when the door is opened due to air  
starvation.  
Flex Line  
Wire Tie  
Figure 39.1 - Floor & Rear Installation  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Burn wood only. Other types of fuels may generate  
poisonous gases (e.g., carbon monoxide).  
B. Mobile Home Installation  
You must use an authorized Outside Air Kit Part  
OAK-ACC for installation in a mobile home.  
11. If unit burns poorly while an exhaust blower is on in  
home, (i.e., range hood), increase combustion air.  
12. Installation shall be in accordance with the Manufacturers  
Home & Safety Standard (HUD) CFR 3280, Part 24.  
1. An outside air inlet must be provided for combustion See  
page 39 for installation information.  
2. Appliance must be secured to the mobile home structure  
at two attachment points by bolting the pedestal through  
hearth pad and into floor.  
Spark Arestor Cap  
3. Appliance must be grounded with #8 solid copper  
grounding wire or equivalent and terminated at each end  
with N.E.C. approved grounding device.  
Storm Collar  
4. Appliance must be installed with an approved UL103 HT  
ventilated chimney connector, UL103 HT chimney, and  
terminal cap with spark arrestor. Never use a single wall  
connector (stove pipe) in a mobile home installation. Use  
only double-wall connector pipe, Dura-Vent DVL, Selkirk  
metalbestos DS or Security DL double-wall connector or  
any Listed double-wall connector pipe.  
Roof Flashing  
Joist Shield/Firestop  
Double wall  
connector pipe  
5. In Canada, this appliance must be connected to a 6 inch  
(152mm) factory-built chimney conforming to CAN/ULC-  
629M, STANDARD FOR FACTORY BUILT CHIMNEYS.  
6. Follow the chimney and chimney connector manufacturer’s  
instructions when installing the flue system for use in a  
mobile home.  
7. Maintain clearance to combustibles.  
Outside Air  
Rear Vent  
8. Floor protection requirements must be followed  
precisely.  
9. Use silicone to create an effective vapor barrier at the  
location where the chimney or other component penetrates  
to the exterior of the structure.  
Floor Protector  
NOTE:  
Offsets from the vertical, not exceeding 45°, are allowed  
per Section 905(a) of the Uniform Mechanical Code  
(UMC).  
Outside Air Floor Vent  
Figure 40.1  
Offsets greater than 45° are considered horizontal and are  
also allowed, providing the horizontal run does not exceed  
75% of the vertical height of the vent.  
CAUTION!  
Construction, clearance and termination must be in com-  
pliance with the UMC Table 9C. This installation must also  
comply with NFPA 211.  
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME  
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED  
NOTE: Top sections of chimney must be removable to allow  
maximum clearance of 13.5 feet (411cm) from ground level  
for transportation purposes.  
Do NOT cut through:  
• Floor joist, wall, studs or ceiling trusses or any support-  
ing material that would affect the structural integrity.  
WARNING! Risk of Asphyxiation!  
NEVER INSTALL IN A SLEEPING ROOM AS IT WILL  
CONSUME THE OXYGEN IN THE ROOM.  
40  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Blower Installation (Optional)  
D. Adjusting the Blower Speed Control  
The blower speed control for this unit is adjusted at the factory,  
and normally does not require further adjustment.  
1. Align holes in mounting flange of blower with bolt holes in  
appliance. Blower should be positioned at bottom of rear  
outer skin as shown in Figure 41.1.  
2. Insert and tighten bolts supplied with the kit, securing  
blower onto outer wall of appliance.  
NOTE: When the speed control is turned clockwise, it  
will click on to high speed. Continue to turn the speed  
control clockwise to decrease the speed. At full clock-  
wise, the blower should blow gently, but should not  
stop.  
3
Place the bracket containing the snap disc and magnet  
under the bottom left rear corner as shown in Figure 41.1.  
See pages 14 and 21 for detailed operating instructions  
for the blower and snap disc.  
CAUTION! Risk of Shock!  
• Do NOT remove grounding prong from plug.  
• Plug directly into properly grounded 3 prong receptacle.  
• Route cord away from appliance.  
Do NOT route cord under or in front of appliance.  
Blower  
Snap Disc  
Snap Disc Bracket  
with Magnet  
MANUAL: Over-rides the  
Snap Disc  
AUTO: Fan will turn ON/OFF  
Automatically by the Snap Disc  
Controls the Fan Speed  
Figure 41.1  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Beginning Mfg Date: April, 2010  
Ending Mfg Date:  
Reference Materials  
10  
A. Exploded View  
3
1
2
4
5
6
13 See Burn Rate Kit Detail Below  
12  
11  
7
9
8
10  
13 Inlet Assembly  
14 Door Assembly  
A
F
B
G
H
E
C
I
D
Part number list on following page.  
05/10  
42  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO ORDER  
To order the entire assembly, order the top line part number only.  
To order an individual part from an assembly, order the part(s) listed  
in the indented portion.  
B. Service Parts & Accessories  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
1
DESCRIPTION  
Convection Air Channel  
COMMENTS  
PART NUMBER  
SRV7057-112  
SRV7056-116  
SRV7057-010  
832-3390  
2
Combustion Air Channel  
Side Panel-Left  
3
Y
Y
4
Ceramic Blanket (1/2" Thick)  
Baffle Board  
Pkg of 2  
SRV7057-116  
SRV7056-147  
SRV7057-118  
SRV7057-005  
SRV7044-217  
SRV7057-008  
SRV7057-122  
SRV7057-007  
5
6
Baffle Protection Channel  
Retainers- Tube Support  
Pedestal Assembly  
OA Cover Plate  
7
8
9
Side Panel-Right  
10  
11  
12  
13  
A
Tube Channel Cover  
Tube Channel Assembly  
Burn Rate Control  
Burn Rate Control Assembly  
Spring Handle, 1/4" Black  
Door Gasket  
Y
SRV7057-011  
SRV7000-614  
7033-282  
Y
Y
Y
B
C
D
E
Inlet Door Assembly  
Inlet Lever  
SRV7056-009  
SRV7057-113  
SRV7056-011  
SRV7044-191  
SRV7044-027  
7000-606/2  
Door Assembly  
Y
14  
F
Pkg of 2  
Glass Frame  
G
H
I
Glass Assembly  
Y
Y
Y
Hinge Pins  
Pkg of 2  
Door Hardware  
SRV7056-012  
832-1680  
Gasket, Door rope  
7 FT Length  
Brick Assembly  
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
2
1
Brick Assembly  
SRV7057-003  
Y
1
2
Brick 1 (9 X 4.35 X 1.25)  
Brick 2 (9 X 2.25 X 1.25)  
Brick, Single Uncut  
Qty 20 Req  
Qty 4 req.  
832-0550  
832-3040  
Y
Y
Brick, 6 Pack Uncut  
Additional Service Parts on following page.  
05/10  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO ORDER  
B. Service Parts & Accessories (Cont’d)  
To order the entire assembly, order the top line part number only.  
To order an individual part from an assembly, order the part(s) listed  
in the indented portion.  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
Component Pack  
COMMENTS  
PART NUMBER  
SRV7057-006  
Contains: Screws, Handle, Spring Handle (1/4" Black), Warranty Card, OA Cover Plate,  
Manual, Efficiency Label, EPA Label, and Startup and Maintenance Guide  
Accessories  
Blower Assembly  
BK-ACC  
Blower Control Box W/Switch  
Blower Replacement  
SRV7000-194  
812-4900  
Y
Component Pack  
SRV7033-051  
SRV7000-140  
7033-036  
Magnet Round  
Y
Y
Snap Disc Bracket Assembly  
Snap Disc, #1, Convection Blower  
Wire Harness  
SRV230-0470  
7033-036  
Outside Air Kit  
OAK-ACC  
7033-039  
Outside Air Collar Assembly  
Outside Air shield  
33271  
Y
Fastener Packs  
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
AVK Rivnut Repair Kit 1/4 -20 & 3/8-16 Rivnut Tools  
RIVNUT-REPAIR  
25221A/10  
Bolt, Hex Head  
Pkg of 10  
Pkg of 25  
Pkg of 24  
Pkg of 24  
Pkg of 25  
Pkg of 25  
Pkg of 25  
Pkg of 40  
Pkg of 24  
Pkg of 25  
Guide Pin Sleeve  
31120/25  
Nut SER FL SMALL 1/4-20  
Nut, 2-WY SIDE-LOCK JAM 3  
Nut, Lock 1/4-20  
226-0130/24  
226-0100/24  
226-0090/25  
220-0080/25  
220-0030/25  
12460/40  
Screw HWH MS 1/4-20 X3/4 NS  
Screw PH PHL TC 8-32X1/2  
SMS #8 X 1/2 S-GRIP BO  
Washer, 1/4 SAE  
28758/24  
Washer, SAE  
227-0080/25  
05/10  
44  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Service And Maintenance Log  
Date of Service  
Performed By  
Description of Service  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Service And Maintenance Log (Cont’d)  
Date of Service  
Performed By  
Description of Service  
46  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Homeowner’s Notes  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E. Contact Information  
CONTACT INFORMATION:  
Hearth & Home Technologies  
1445 North Highway  
Colville, WA 99114  
Division of HNI INDUSTRIES  
Please contact your Heatilator dealer with any questions or concerns.  
For the number of your nearest Heatilator dealer, please visit www.heatilatorecochoice.com.  
NOTICE  
DO NOT DISCARD THIS MANUAL  
Read, understand and  
follow these instructions  
for safe installation and  
operation.  
Leave this manual with  
party responsible for  
use and operation.  
Important operating  
and maintenance  
instructions included.  
We recommend that you record the following pertinent  
information for your ECO-CHOICE WS22 Wood Stove  
Date purchased/installed:  
Serial Number:  
Location on appliance:  
Dealer phone:  
Dealership purchased from:  
Notes:  
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645,  
7047962 or other U.S. and foreign patents pending.  
48  
Heatilator • ECO-ADV-WS22 • 7057-128C • August 13, 2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grindmaster Coffeemaker PIC 2 User Manual
Grizzly Lathe G9036 User Manual
Grizzly Sander H8215 User Manual
Haier Washer Dryer 0020504712K User Manual
Hasbro Motorized Toy Car 49597 User Manual
Hotpoint Washer WMF 760 P G A K User Manual
HP Hewlett Packard Network Cables NC6136 User Manual
HP Hewlett Packard Welding System 6112A User Manual
iHome MP3 Player Accessories ID37 User Manual
Imperial Dehumidifier SHMTM User Manual