Model iD37
The Home System
For Your iPad, iPhone® or iPod®
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
Preset Buttons 1-6
Side Panel
Top Panel
Radio aux Button
Time sync Button
Alarm 1 Button
Alarm 2 Button
EQ Button
Reverse/Set Button
Play/Pause Button
Raise Volume Button
Lower Volume Button
Forward/Set Button
Dock
Snooze/Dimmer Button
Sleep Button
USB charging port
Power/Alarm Reset Button
Switch charging circuit
Rear Panel
Time Zone Button
Rubber Collar
(to dock iPad/iPhone/iPod without case)
DST switch
Time Set Button
Aux-in Jack
AC Adaptor Jack
FM antenna
iD37 Display
NOTE: AM/PM indicators will not appear
when clock is set to 24 hour display mode
Time Display
PM Indicator
AM Indicator
Wake to Icon
Battery Low Indicator
wake-to
Sleep / FM Radio Icon
Alarm 2 Indicator
Alarm 1 Indicator
Alarm Time Display
1
Download from Www.Somanuals.com. All Manuals Search And Download.
iD37 Quick start
3: clock adjust
1: power
2:
Place rubber collar over dock
to dock an iPad, iPhone or
iPod with no case
To Set Time using Time Sync:
• Dock your iPhone, iPad or iPod
touch
• Press and release the Time Sync
Button on the top of the unit.
“SYNC” will flash in the display,
indicating sync attempt. If sync is
successful, “SYNC OK” will
appear. If “FAILED” appears, try
again with a different iPhone, etc.,
or set manually.
Attach AC adaptor cable to DC
jack on back of the unit and plug
the other end into a working outlet.
Remove rubber collar to dock
an iPad, iPhone or iPod in a
thick case
To Set Time Manually:
• Slide the DST switch on back of
the unit to +1 add an hour or to
–1 to subtract an hour.
5: iPad/iPhone/iPod
4: time zone
• Press & hold the Time Set
button on back until the display
flashes, then release.
• Press the << or >> Button to set
the correct time.
• Press the Time Set button and
use the << or >> Button to set
correct year.
The unit is preset to the Eastern time
zone. To change the time zone:
• Press & hold the Time Zone
button on back of the unit until
display flashes, then release it.
• Press the << or >> button to
select your time zone.
• Gently dock playing iPad/iPhone
/iPod. The unit will turn on.
• Press the Time Set button and
use the << or >> Button to set
correct date (hold for rapid
setting).
• Press the or
volume
buttons to adjust
• Press the EQ Button to cycle to
Treble, Bass and Balance, press <<
or >> to adjust settings.
• Press the Time Set button. 2
beeps indicate time setting is
completed.
• Press and release the Time Zone
button to confirm.
• Press the
Button to turn unit off.
• Press the radio/aux button to select FM radio mode.
• Press the << or >> Button to select a station (press and hold
briefly to find next clear station).
6: radio
• See page 5 for programming presets.
• Press the
button to turn unit off.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Installing/Replacing the Backup Batteries
This unit uses “AA” LR06 batteries (pre-installed) for backup battery system to provide continuous
alarm operation and clock settings in the event of a power failure. If the Battery Low Icon
located on the right of the display is flashing, it is time to replace the backup batteries. Please
make sure the AC adaptor is connected, otherwise all settings may be lost during battery
replacement.
1. Open the battery compartment cover located on the bottom of the unit
2. Insert 2 “AA” (LR06) batteries as indicated, making sure that the + and – polarities match
the diagram inside.
3. Replace battery compartment cover.
We recommend alkaline batteries for longer battery life.
Battery Warning
For models that require more than one battery
• Do not mix with used or other battery types/brands
• Replace all batteries at the same time
• Do not open batteries
• Do not dispose of in fire
• Do not heat above 75ºC (167ºF)
• Do not expose contents to water
• Do not charge or recharge
• Do not install backwards
Setting Up the Unit
Connect Unit to Power Source
Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120V AC wall socket. Adaptor must
be plugged in to operate unit. The unit does not operate on batteries (a battery back up system maintains clock settings
during power failures).
This unit has a preset clock: the clock is preset at the factory. It’s simple to match the Time Zone setting to your location (US
only).
1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, manually set the DST Switch located
at the back of the unit to +1 to add an hour or to -1 to subtract an hour. A DST adjust screen appears briefly.
2. Press and hold the Time Zone Button located on the back of the unit until the Time Zone flashes on the lower part of the
display. Press the << or >> Button to select your time zone. Note: Time Zone is disabled when clock display is set to 24
hours (see step 5 under Setting Time).
3. Press the Time Zone Button again (or no button within 10 seconds) to exit the time zone setting mode.
4. If the displayed time is not correct, please see “Setting Time and Calendar manually” section below.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Unit
Sync Time to iPhone/iPad/iPod
The Time Sync feature allows you to sync the time setting on the unit to the time from your iPhone, iPad or recent model iPod
Touch, iPod Nano and iPod Classic (older iPod models such as iPod mini do not support this feature).
1. Dock your iPhone, iPad or iPod
2. Press and release the Time Sync Button located on top of the unit.
3. The unit will sync to the time on your iPhone/iPad/iPod. Once sync is completed,“SYNC OK” will appear on the display.
4. If sync was not successful, “Failed” will appear on the display. If this happens, please try again, with a different iPhone/iPad/iPod
if needed. If time sync still fails, please set time manually (see below).
NOTE: The iPhone is constantly updated to current time via cell phone towers. The time on your iPad or iPod is only accurate
to the last time it was synced to a computer. It’s possible to have up to 59 seconds difference between the iD37 and synced
iPhone/iPad/iPod.
Setting Time and Calendar manually
1. Press and hold the Time Set Button located at the back of the unit until the time flashes on the display.
2. Press the << or >> Button to set the correct time. Remember to set the correct AM or PM time. The AM/PM Indicators
appear to the left of the time display (except when clock display is set to 24 hour mode-- see step 5).
3. Press the Time Set Button again. The year will flash. Press the << or >> Button to adjust to the current year.
4. Press the Time Set Button again. The month and date will flash. Press the << or >> Button to adjust to the current
month/date.
5. During Time set, press either the
or
button to toggle the clock display format to 12 hours or 24 hours.
6. Press the Time Set Button again (or no button within 10 seconds) to exit time/calendar setting mode. 2 beeps will
confirm time setting is complete.
Using the Alarms
The unit has a dual alarm system so you can set two separate alarms to different alarm times, wake-to sources and frequencies
(daily, weekdays or weekend).
Setting the Alarms
1. Press and hold the
or
Button until the alarm time flashes on the lower part of the display. Press the << or >>
Button to set the alarm time (hold for faster setting). Remember to set the correct AM or PM time.
2. Press the Alarm Button again to confirm the desired alarm time and then press the << or >> Button to set the alarm
frequency (7 = the whole week, 5 = weekdays, 2 = weekends only).
3. Press the Alarm Button again to confirm alarm frequency then Press the << or >> Button to select an alarm source to
wake to: Buzzer, Playlist (user created), iPhone/iPad/iPod or Radio.
NOTE: to wake to playlist, you must first create a playlist named “iHome” in iTunes and import it to your iPhone/iPad/iPod.
The unit will play music randomly from within the “iHome” playlist.
If the selected alarm source is iPod and no iPhone/iPad/iPod is docked/detected, the unit will default to a buzzer alarm.
4. For wake to radio, after selecting Radio as wake to source, press the Alarm Button again and press the << or >>
Button to select a different radio station or press one of the preset buttons to wake to a preset radio station (see Using
Radio on page 6 for details on setting radio stations and presets).
5. Press the Alarm button again (or no button within 10 seconds) to exit the alarm setting mode. The alarm will be armed
once set and the corresponding alarm icon will light up. The lower part of the display will show the earliest set alarm time.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Unit
Reviewing, Arming and Disarming Alarm (Turn Alarm Function On and Off)
1. Once an alarm is armed, the lower part of the display will show the alarm time and the alarm icon. If more then one alarm is armed, the
earliest alarm time will show along with both icons.
2. To review the alarm time, press the
3. During alarm review, press the or
or
Button once. The related alarm time will show on the lower part of the display.
Button once to toggle it on or off. If the alarm is armed, the related alarm icon will light up.
Resetting the Alarm to Come on the Next Day
When an alarm is sounding, press the
Button to stop the alarm and reset it to come on the next set day. For example, if an alarm is set
for 5 days and you press the alarm reset on Friday, the alarm will come on again on Monday, not Saturday.
Snooze Operation
1. Press and hold the Snooze/Dimmer Button for a few seconds until the snooze time flashes. Press the << or >> Button to set the snooze
timer from 1 to 29 minutes.
2. Press the Snooze/Dimmer Button after an alarm sounds. The alarm will be silenced for the set snooze duration time then sound again.
Snooze can be pressed several times during the 1 hour alarm cycle.
Sure Alarm
The iD37 has a sure alarm feature. If backup batteries are installed, the buzzer alarm will still sound in the event of a power failure.
Docking & Charging your iPad, iPhone or iPod
Make sure your iPad/iPhone/iPod’s firmware is up to date via iTunes before use. If your iPod/iPhone/iPad is in a thick case or skin,
remove the rubber dock collar before docking. If you do not use a case or skin on your iPod/iPhone/iPad, you can place the rubber
dock collar on the unit (place over dock with tabs in slots on cabinet) for added stability when docking. Carefully dock your
iPad/iPhone/iPod onto the dock. Your iPad, iPhone or iPod will charge while docked.
Listening to iPhone/iPad/iPod, Radio
Charging your iPhone/Pod
While an iPhone/iPad/iPod is docked in the unit and the unit is connected to AC power, it recharges until fully charged.
Listening to iPhone/iPad/iPod
1. Dock an already-playing iPhone/iPad/iPod in the dock. The iD37 will automatically turn on and you will hear the audio playing from your
iPhone/iPad/iPod.
Note: If the audio volume is too low on the iPod itself, the iD37 may not detect iPod is in play mode. Press the
Button to play it.
2. When an iPhone/iPad/iPod is docked and in standby mode, press the
the display to show the iPhone/iPad/iPod is currently in play mode.
Button to play it. “iPod” will appear briefly in the lower part of
3. Press the
4. Press the
Button again to pause play; press again to resume it.
or
Button to adjust the system volume.
5. Press the EQ Button to select and press the << or >> Button to adjust Treble, Bass, and Left/Right Balance.
6. To turn off the unit, press the
Button. An iPhone/iPad/iPod will continue charging while docked.
Listening to Radio
Setting up Antenna
Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.
Tuning and Playing the Radio
1. Press the Radio/Aux Button as needed to turn on the unit and choose between FM radio and aux line-in modes.
2. When FM radio mode is selected, press the << or >> Button to tune the radio to a desired station (hold to scan to the next clear station).
The radio frequency appears in the lower part of the display.
3. To memorize a station as a preset, press the << or >> Button to select your station. Press and hold the desired Preset Button until
odd number preset (P1, etc) flashes on display; press again for even number presets and allow to time-out. You will hear 1 beep confirming
the preset has been assigned.
4. To access a preset station, press the desired Preset Button once (for odd number presets) or twice (for even number presets).
5. Press the
or
Button to adjust the system volume.
6. Press the EQ Button to select and press the << or >> Button to adjust Treble, Bass, and Left/Right Balance.
7. To turn off the unit, press the
Button. An iPhone/iPad/iPod will continue charging while docked.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Aux device
Using the Aux line-in Jack
You can play any audio device that has a line out or headphone jack through the iD37 via the aux line-in Jack.
1. Plug one end of a standard 3.5mm stereo audio patch cord (not included) into the headphone or line-out jack on your
device and the other end of the patch cord into the aux line-in Jack located on the back of the unit.
2. Press the Radio/Aux Button once or twice until “aux” appears in the lower part of the display.
3. Turn on and play your device.
4. Press the or
Button to adjust the iD37 volume. You may need to adjust volume on your audio device, too.
5. Press the EQ Button to select EQ mode then press the << or >> Button to adjust Treble, Bass, and Left/Right Balance.
6. To turn off the unit, press the
Button. Please remember to turn off your device, too.
Sleep mode, Dimmer, USB Charging
Sleep Operation
Sleep mode lets you sleep to your iPhone/Pod or radio, gradually lowering the volume until the unit shuts off at the selected time.
1. Press the Sleep Button to enter sleep mode. The sleep time will show in the lower display.
2. Press the Sleep Button again as needed to adjust the sleep timer to 120, 90, 60, 30, 15 minutes or OFF.
3. When the display changes back to show the real time, press the Sleep Button once to show the sleep time remaining.
Pressing it again will change sleep time to the next lowest increment.
4. The unit has independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the normal
volume. The sleep volume will remain at that level the next time you enter sleep mode until controls are changed.
5. To stop listening at any time, press the
Button to turn unit off.
Dimmer Operation
During normal operation, press the Snooze/Dimmer Button to control the brightness of the LCD display.
Charging a USB Device
Plug one end of a USB cable (not included) into the device you wish to charge and the other into the USB port located on the
right side of the unit. Observe the charging status on your deivce. If the device is not charging, switch the USB circuit switch
to the other position. Note: Some devices use a proprietary USB connections and cannot be charged by the iD37.
Using the Unit in Other Countries
Different regions of the world use different FM radio frequency steps and ranges. You will need to select the one that matches
the standards in your region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is USA; if you live in the US,
you may skip this section.
1. Make sure the iD37 is OFF (not playing in any mode). Press and hold the Radio/Aux Button for about 5 seconds until
“USA” appears in the lower part of display. Press the << or >> Button to adjust country frequency to your region.
2. Press the Radio/Aux Button again (or no button within 5 seconds) to exit the radio frequency setting mode.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in
these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through
the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where
it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning
instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings
or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A.
the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E.
the unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power
cable should be unplugged from the unit to prevent damage or corrosion.
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Possible Problem
Solution
Symptom
AC adaptor isn't plugged into a working wall
socket or not plugged into the power supply
jack on back of the unit
iD37 does not turn on
Plug the AC adaptor into a working wall socket and plug the
connector into the supply jack on the unit
iD37 doesn’t respond
If unit is plugged in and doesn't respond, try resetting the unit by
following these steps:
iD37 requires a reset
a) remove iPhone/iPad/iPod from dock
b) unplug unit from power source
c) remove back up batteries
d) wait a few minutes, then resume use
Remove your iPhone/iPad/iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPhone/iPad/iPod. Then reseat it in the dock.
iPhone/iPad/iPod is not docked properly
Battery Low icon
always flashing
Replace with new batteries
Batteries are weak
Check to make sure the polarity ( + and – ends) matches the
diagram in the battery compartment
Batteries were not installed properly
Remove your iPhone/iPad/iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPhone/iPad/iPod. Then reseat it in the dock.
iPhone/iPad/iPod
does not respond to
the unit
iPhone/iPad/iPod is not docked properly
Your iPhone/iPad/iPod software is too old
Upgrade software on your iPhone/iPad/iPod via iTunes on your
computer
iPhone/iPad/iPod is locked up/plays but no
sound comes out
Check the volume setting. Make sure your iPhone/iPad/iPod is working
properly before docking into the unit. Please refer to your
iPhone/iPad/iPod manual for details. See above for software upgrade
information. You may need to reset your iPhone/iPad/iPod. Refer to
your iPhone or iPod user guide for details on how to perform a reset.
Using 1st or 2nd generation iPod, iPod
shuffle or other devices.
iD37 cannot control those iPod models or other devices.
iD37/iPhone/iPad/
iPod performance is
erratic
Move unit away from potential sources of external interference such
as computers, modems, wireless devices (routers) or fluorescent
light.
The iD37 is reacting to external interference
Volume is set too low on iD37
No sound from iD37
Make sure volume is turned up
Remove your iPhone/iPad/iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPhone/iPad/iPod. Then reseat it in the dock.
iPhone/iPad/iPod is not docked properly
iPhone/iPad/iPod
didn’t charge up
iPhone/iPad/iPod is locked up/ frozen
iPhone/iPad/iPod battery has problem
Please make sure your iPhone/iPad/iPod is working properly
before docking into the unit. Please refer to your iPhone/iPad/iPod
manual for details.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Possible Problem
Solution
Symptom
Sound is distorted
Volume level is set too high
Decrease the volume
If the iPhone/iPad/iPod original sound source (MP3) is old or of poor
quality, distortion and noise are easily noticed with high-power
speakers. Try a different file from a trusted sources such as iTunes
Sound source is distorted
If you are using an external sound source like older generation of
iPod or iPod Shuffle, try reducing the output volume on the device
itself. Also try turning bass boost OFF.
Lower EQ settings.
EQ settings are too high.
This is normal
Unit/adaptor gets
warm after extended
play at high volume
Turn unit off for a while or lower volume
Snooze time is too
long/short
Custom snooze time not set
Press and hold Snooze button then turn Set Wheel to adjust
When setting clock or alarm time, take note of the AM/PM
indicators
AM/PM time/alarm time not set correctly
Alarm not working
Alarm time or source selected for alarm 2,
not or alarm 1 or vice versa
Make sure to set the alarm time and source for the alarm icon 1
or 2 that is shown on the clock display
7 days is every day alarm, 5 days is Mon-Fri, and 2 days is Sat-Sun.
See page 5 for setting alarms.
7-5-2 days setting is not correct
Calendar is not set correctly, which can
affect 7/5/2 day alarm operation
See page 4 for Time/Calendar setting section.
Make sure you are using an iPhone or newer iPod such as touch, nano
or classic. If not available, set time manually (see page 4).
Older iPod models such as iPod mini do not
support time sync function
Time sync didn’t work
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 1 Year Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from
defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period,
SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $20.00 charge for handling, packing,
return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product
to the Factory Service Center listed below. The product must include proof of purchase, including date of purchase. The fee for service
without proof of purchase is $40.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective
batteries are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty
period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $20.00 ($40.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Dr.
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions
may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
Toll Free Customer Service: 1-800-288-2792
©SDI Technologies 2010 All rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
iD37-031811
Printed in China
|