Heat Glo LifeStyle Indoor Fireplace 6000C User Manual
Owner’s Manual  
Installation and Operation  
Models:  
6000C  
6000C-LP  
6000C-IPI  
6000C-IPILP  
8000C  
8000C-LP  
8000C-IPI  
8000C-IPILP  
NOTICE  
DO NOT DISCARD THIS MANUAL  
• Important operating  
and maintenance  
instructions included.  
• Read, understand and follow  
these instructions for safe  
installation and operation.  
• Leave this manual with  
party responsible for use  
and operation.  
WARNING  
WARNING: If the information in these  
instructions is not followed exactly, a fire  
or explosion may result causing property  
damage, personal injury, or death.  
HOT SURFACES!  
Glass and other surfaces are hot during  
operation AND cool down.  
Hot glass will cause burns.  
• DO NOT touch glass until it is cooled  
• NEVER allow children to touch glass  
• Keep children away  
• DO NOT store or use gasoline or other flam-  
mable vapors and liquids in the vicinity of this  
or any other appliance.  
• CAREFULLY SUPERVISE children in same room as  
fireplace.  
• Alert children and adults to hazards of high temperatures.  
• What to do if you smell gas  
- DO NOT try to light any appliance.  
High temperatures may ignite clothing or other flammable  
materials.  
• Keep clothing, furniture, draperies and other flammable  
materials away.  
- DO NOT touch any electrical switch. DO  
NOT use any phone in your building.  
- Immediately call your gas supplier from a  
neighbor’s phone. Follow the gas suppli-  
er’s instructions.  
This appliance has been supplied with an integral barrier  
to prevent direct contact with the fixed glass panel. DO  
NOT operate the appliance with the barrier removed.  
- If you cannot reach your gas supplier, call  
the fire department.  
Contact your dealer or Hearth & Home Technologies if the  
barrier is not present or help is needed to properly install one.  
• Installation and service must be performed  
by a qualified installer, service agency, or the  
gas supplier.  
In the Commonwealth of Massachusetts installation must be  
performed by a licensed plumber or gas fitter.  
See Table of Contents for location of additional Commonwealth  
of Massachusetts requirements.  
This appliance may be installed as an OEM installation in  
manufactured home (USA only) or mobile home and must be  
installed in accordance with the manufacturer’s instructions  
and the manufactured home construction and safety standard,  
Title 24 CFR, Part 3280 or Standard for Installation in Mobile  
Homes, CAN/CSA Z240MH, in Canada.  
Installation and service of this appliance should be  
performed by qualified personnel. Hearth & Home  
Technologies suggests NFI certified or factory trained  
professionals, or technicians supervised by an NFI  
certified professional.  
This appliance is only for use with the type(s) of gas indicated  
on the rating plate.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Safety Alert Key:  
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.  
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.  
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.  
• NOTICE: Used to address practices not related to personal injury.  
Table of Contents  
6 Termination Locations  
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5  
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 25  
1 Listing and Code Approvals  
7 Vent Information and Diagrams  
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 7  
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 7  
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 8  
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 8  
G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
H. Requirements for the Commonwealth of Massachusetts. . 9  
A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
8 Vent Clearances and Framing  
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 39  
B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 39  
C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 40  
D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 41  
E. Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . . 41  
User Guide  
2 Operating Instructions  
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 11  
F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
G. Remote Controls, Wall Controls and Wall Switches. . . . . 11  
H. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . 12  
I. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 12  
J. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 12  
K. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 13  
L. Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . . 14  
M. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
N. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 15  
9 Appliance Preparation  
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
C. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 44  
D. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 44  
10 Installing Vent Pipe (DVP and SLP Pipe)  
A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 45  
B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 46  
C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
D. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 47  
E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 47  
F. Install Decorative Ceiling Components (SLP only). . . . . . 48  
G. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 49  
H. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 49  
I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 50  
J. Install Decorative Wall Components (SLP only). . . . . . . . 50  
K. Heat Shield Requirements for Horizontal Termination . . . 50  
L. Install Horizontal Termination Cap (DVP and SLP Pipe) . 51  
3 Maintenance and Service  
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 16  
B. Maintenance Tasks-Qualified Service Technician . . . . . . 17  
C. Refractory, Grate and Valve Assembly Removal . . . . . . . 18  
D. Burner Identification/Verification. . . . . . . . . . . . . . . . . . . . 19  
Installer Guide  
11 Gas Information  
4 Getting Started  
A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 52  
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 20  
B. Design and Installation Considerations . . . . . . . . . . . . . . 21  
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 21  
D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 21  
12 Electrical Information  
5 Framing and Clearances  
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
B. IntelliFire Plus™ Ignition System Wiring . . . . . . . . . . . . . 53  
C. Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . . 53  
D. Optional Accessories Requirements . . . . . . . . . . . . . . . . 53  
E. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 55  
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 22  
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 23  
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 24  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 55  
G. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 55  
13 Finishing  
A. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 56  
B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
C. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57  
D. Elevated Hearth Systems. . . . . . . . . . . . . . . . . . . . . . . . . 60  
14 Appliance Setup  
A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 61  
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 61  
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
E. Burner Top Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
F. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
G. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 62  
H. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
I. Install Trim and/or Surround. . . . . . . . . . . . . . . . . . . . . . . 66  
J. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
15 Troubleshooting  
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 67  
B. IntelliFire Plus™ Ignition System . . . . . . . . . . . . . . . . . . . 69  
16 Reference Materials  
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 70  
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 72  
C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81  
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86  
= Contains updated information.  
4
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Limited Lifetime Warranty  
Hearth & Home Technologies Inc.  
LIMITED LIFETIME WARRANTY  
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for  
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.  
WARRANTY COVERAGE:  
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership  
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance  
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-  
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,  
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its  
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product  
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty  
is subject to conditions, exclusions and limitations as described below.  
WARRANTY PERIOD:  
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage  
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,  
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months  
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for  
parts and labor for covered components is produced in the following table.  
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for  
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These  
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.  
Warranty Period  
Parts Labor  
HHT Manufactured Appliances and Venting  
EPA  
Components Covered  
Gas  
X
Wood Pellet  
Coal Electric Venting  
Wood  
All parts and material except as  
covered by Conditions,  
Exclusions, and Limitations  
listed  
1 Year  
X
X
X
X
X
X
Igniters, electronic components,  
and glass  
X
X
X
X
X
X
2 years  
X
X
X
Factory-installed blowers  
Molded refractory panels  
3 years  
X
X
Firepots and burnpots  
Castings and baffles  
5 years 1 year  
X
X
Manifold tubes,  
HHT chimney and termination  
7 years 3 years  
X
X
10  
1 year  
years  
X
X
X
Burners, logs and refractory  
Firebox and heat exchanger  
Limited  
3 years  
Lifetime  
X
X
X
X
X
X
X
X
All replacement parts  
beyond warranty period  
90 Days  
X
X
See conditions, exclusions, and limitations on next page.  
4021-645C 12-29-10  
Page 1 of 2  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Limited Lifetime Warranty (continued)  
WARRANTY CONDITIONS:  
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of  
HHT authorized dealers is available on the HHT branded websites.  
•
•
This warranty is only valid while the HHT appliance remains at the site of original installation.  
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact  
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service  
from a dealer other than the dealer from whom you originally purchased the product.  
•
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges  
for parts are not covered by this warranty.  
WARRANTY EXCLUSIONS:  
This warranty does not cover the following:  
•
•
•
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and  
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.  
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,  
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.  
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts  
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-  
ation of glass.  
•
•
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-  
plaints related to this noise are not covered by this warranty.  
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation  
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to  
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-  
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/  
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting  
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or  
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)  
installation or use of components not supplied with the appliance or any other components not expressly authorized  
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;  
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.  
•
•
•
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.  
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.  
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-  
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-  
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of  
the structure.  
This warranty is void if:  
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging  
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,  
cracking and discoloration of steel or enamel finishes.  
•
•
The appliance is subjected to prolonged periods of dampness or condensation.  
There is any damage to the appliance or other components due to water or weather damage which is the result of, but  
not limited to, improper chimney or venting installation.  
LIMITATIONS OF LIABILITY:  
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or  
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no  
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states  
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.  
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO  
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY  
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE  
EXPRESSED WARRANTY SPECIFIED ABOVE.  
4021-645C 12-29-10  
Page 2 of 2  
6
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listing and Code Approvals  
1
A. Appliance Certification  
C. BTU Specifications  
Maximum Minimum Orifice  
Models  
(U.S. or Canada)  
Input  
Input  
Size  
MODELS: 6000C, 6000C-IPI, 8000C, 8000C-IPI  
LABORATORY: Underwriters Laboratories, Inc. (UL)  
TYPE: Direct Vent Gas Appliance Heater  
BTU/h  
BTU/h  
(DMS)  
US  
(0-2000 FT)  
30,000  
27,000  
29,000  
26,100  
35,000  
31,500  
34,000  
16,000  
14,400  
17,000  
15,300  
19,000  
17,100  
17,000  
37  
38  
52  
53  
33  
34  
50  
6000C (NG)  
6000C-IPI (NG)  
STANDARD: ANSI Z21.88b-2008 • CSA 2.33a-2008  
CANADA  
(2000-4500 FT)  
US  
(0-2000 FT)  
This product is listed to ANSI standards for “Vented Gas  
Appliance Heaters” and applicable sections of “Gas Burn-  
ing Heating Appliances for Manufactured Homes and  
Recreational Vehicles”, and “Gas Fired Appliances for  
Use at High Altitudes”.  
6000C-LP  
6000C-IPILP  
CANADA  
(2000-4500 FT)  
US  
(0-2000 FT)  
8000C (NG)  
8000C-IPI (NG)  
CANADA  
(2000-4500 FT)  
NOTICE: This installation must conform with local codes.  
In the absence of local codes you must comply with the  
National Fuel Gas Code, ANSI Z223.1-latest edition in  
the U.S.A. and the CAN/CGA B149 Installation Codes in  
Canada.  
US  
(0-2000 FT)  
8000C-LP  
8000C-IPILP  
CANADA  
(2000-4500 FT)  
30,600  
15,300  
51  
D. High Altitude Installations  
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.  
This appliance is tested and approved as either supplemen-  
tal room heat or as a decorative appliance. It should not be  
factored as primary heat in residential heating calculations.  
NOTICE: If the heating value of the gas has been reduced,  
these rules do not apply. Check with your local gas utility  
or authorities having jurisdiction.  
When installing above 2000 feet elevation:  
B. Tempered Glass Specifications  
• In the USA: Reduce input rate 4% for each 1000 feet  
above 2000 feet.  
Hearth & Home Technologies appliances manufactured  
with tempered glass may be installed in hazardous loca-  
tions such as bathtub enclosures as defined by the Con-  
sumerProductSafetyCommission(CPSC).Thetempered  
glass has been tested and certified to the requirements  
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing  
Certification Council SGCC# 1595 and 1597. Architectur-  
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).  
• In CANADA: Reduce input rate 10% for elevations  
between 2000 feet and 4500 feet. Above 4500 feet,  
consult local gas utility.  
Check with your local gas utility to determine proper  
orifice size.  
This statement is in compliance with CPSC 16 CFR Sec-  
tion 1201.5 “Certification and labeling requirements”  
which refers to 15 U.S. Code (USC) 2063 stating “…Such  
certificate shall accompany the product or shall otherwise  
be furnished to any distributor or retailer to whom the  
product is delivered.”  
Some local building codes require the use of tempered  
glass with permanent marking in such locations. Glass  
meeting this requirement is available from the factory.  
Please contact your dealer or distributor to order.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
E. Non-Combustible Materials Specification  
Material which will not ignite and burn. Such materials are  
those consisting entirely of steel, iron, brick, tile, concrete,  
slate, glass or plasters, or any combination thereof.  
Materials that are reported as passing ASTM E 136,  
Standard Test Method for Behavior of Materials in a  
Vertical Tube Furnace at 750 ºC and UL763 shall be  
considered non-combustible materials.  
F. Combustible Materials Specification  
Materials made of or surfaced with wood, compressed pa-  
per, plant fibers, plastics, or other material that can ignite  
and burn, whether flame proofed or not, or plastered or  
unplastered shall be considered combustible materials.  
G. Electrical Codes  
NOTICE: This appliance must be electrically wired and  
grounded in accordance with local codes or, in the absence  
of local codes, with National Electric Code ANSI/NFPA  
70-latest edition or the Canadian Electric Code CSA  
C22.1.  
• A 110-120 VAC circuit for this product must be protected  
withground-faultcircuit-interrupterprotection,incompliance  
with the applicable electrical codes, when it is installed in  
locations such as in bathrooms or near sinks.  
8
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Inspection  
Note: The following requirements reference various  
Massachusetts and national codes not contained in this  
document.  
The state or local gas inspector of the side wall horizon-  
tally vented gas fueled equipment shall not approve the  
installation unless, upon inspection, the inspector ob-  
serves carbon monoxide detectors and signage installed  
in accordance with the provisions of 248 CMR 5.08(2)(a)1  
through 4.  
H. Requirements for the Commonwealth of  
Massachusetts  
For all side wall horizontally vented gas fueled equipment  
installed in every dwelling, building or structure used in  
whole or in part for residential purposes, including those  
owned or operated by the Commonwealth and where the  
side wall exhaust vent termination is less than seven (7)  
feet above finished grade in the area of the venting, in-  
cluding but not limited to decks and porches, the following  
requirements shall be satisfied:  
Exemptions  
The following equipment is exempt from 248 CMR  
5.08(2)(a)1 through 4:  
• The equipment listed in Chapter 10 entitled “Equipment  
Not Required To Be Vented” in the most current edition  
of NFPA 54 as adopted by the Board; and  
• Product Approved side wall horizontally vented gas fu-  
eled equipment installed in a room or structure separate  
from the dwelling, building or structure used in whole or  
in part for residential purposes.  
Installation of Carbon Monoxide Detectors  
At the time of installation of the side wall horizontal vented  
gas fueled equipment, the installing plumber or gas fitter  
shall observe that a hard wired carbon monoxide detector  
with an alarm and battery back-up is installed on the floor  
level where the gas equipment is to be installed. In addi-  
tion, the installing plumber or gas fitter shall observe that  
a battery operated or hard wired carbon monoxide detec-  
tor with an alarm is installed on each additional level of  
the dwelling, building or structure served by the side wall  
horizontal vented gas fueled equipment. It shall be the  
responsibility of the property owner to secure the services  
of qualified licensed professionals for the installation of  
hard wired carbon monoxide detectors.  
MANUFACTURER REQUIREMENTS  
Gas Equipment Venting System Provided  
When the manufacturer of Product Approved side wall  
horizontally vented gas equipment provides a venting  
system design or venting system components with the  
equipment, the instructions provided by the manufacturer  
for installation of the equipment and the venting system  
shall include:  
• Detailed instructions for the installation of the venting  
system design or the venting system components; and  
In the event that the side wall horizontally vented gas fu-  
eled equipment is installed in a crawl space or an attic,  
the hard wired carbon monoxide detector with alarm and  
battery back-up may be installed on the next adjacent  
floor level.  
• A complete parts list for the venting system design or  
venting system.  
Gas Equipment Venting System NOT Provided  
In the event that the requirements of this subdivision can  
not be met at the time of completion of installation, the  
owner shall have a period of thirty (30) days to comply  
with the above requirements; provided, however, that dur-  
ing said thirty (30) day period, a battery operated carbon  
monoxide detector with an alarm shall be installed.  
When the manufacturer of a Product Approved side wall  
horizontally vented gas fueled equipment does not pro-  
vide the parts for venting the flue gases, but identifies  
“special venting systems”, the following requirements  
shall be satisfied by the manufacturer:  
• The referenced “special venting system” instructions  
shall be included with the appliance or equipment in-  
stallation instructions; and  
Approved Carbon Monoxide Detectors  
Each carbon monoxide detector as required in accor-  
dance with the above provisions shall comply with NFPA  
720 and be ANSI/UL 2034 listed and IAS certified.  
• The “special venting systems” shall be Product Ap-  
proved by the Board, and the instructions for that sys-  
tem shall include a parts list and detailed installation  
instructions.  
Signage  
A metal or plastic identification plate shall be permanent-  
ly mounted to the exterior of the building at a minimum  
height of eight (8) feet above grade directly in line with the  
exhaust vent terminal for the horizontally vented gas fu-  
eled heating appliance or equipment. The sign shall read,  
in print size no less than one-half (1/2) in. in size, “GAS  
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-  
STRUCTIONS”.  
A copy of all installation instructions for all Product Ap-  
proved side wall horizontally vented gas fueled equip-  
ment, all venting instructions, all parts lists for venting  
instructions, and/or all venting design instructions shall  
remain with the appliance or equipment at the completion  
of the installation.  
See Gas Connection section for additional Common-  
wealth of Massachusetts requirements.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
User Guide  
Operating Instructions  
2
• Keep remote controls out of reach of children.  
A. Gas Fireplace Safety  
• Never leave children alone near a hot fireplace, whether  
operating or cooling down.  
WARNING  
HOT SURFACES!  
• Teach children to NEVER touch the fireplace.  
Glass and other surfaces are hot during  
operation AND cool down.  
• Consider not using the fireplace when children will be  
present.  
Hot glass will cause burns.  
• DO NOT touch glass until it is cooled  
• NEVER allow children to touch glass  
• Keep children away  
Contact your dealer for more information, or visit: www.  
hpba.org/safety-information.  
To prevent unintended operation when not using your fire-  
place for an extended period of time (summer months,  
vacations, trips, etc):  
• CAREFULLY SUPERVISE children in same room as  
fireplace.  
• Alert children and adults to hazards of high temperatures.  
• Remove batteries from remote controls.  
• Turn off wall controls.  
High temperatures may ignite clothing or other  
flammable materials.  
• Keep clothing, furniture, draperies and other flammable  
materials away.  
• Unplug 6 volt transformer plug and remove batteries on  
IPI models.  
This appliance has been supplied with an integral barrier  
to prevent direct contact with the fixed glass panel. DO  
NOT operate the appliance with the barrier removed.  
• Turn off gas controls valve on standing pilot models.  
When lighting the pilot light on fireplaces with a standing  
pilot, remove the fixed glass assembly so you can de-  
tect presence of residual gas build-up. See Standing Pilot  
Lighting instructions and Maintenance Tasks.  
Contact your dealer or Hearth & Home Technologies if the  
barrier is not present or help is needed to properly install one.  
If you expect that small children or vulnerable adults may  
come into contact with this fireplace, the following precau-  
tions are recommended:  
B. Your Fireplace  
WARNING! DO NOT operate fireplace before read-  
ing and understanding operating instructions. Failure  
to operate fireplace according to operating instructions  
could cause fire or injury.  
• Install a physical barrier such as:  
- A decorative firescreen.  
- Adjustable safety gate.  
• Install a switch lock or a wall/remote control with child  
protection lockout feature.  
DECORATIVE DOORS  
(NOT SHOWN)  
SECTION 2.E.  
FIXED GLASS ASSEMBLY  
(NOT SHOWN)  
SECTION 14.H.  
MANTEL  
SECTION 5.D  
FAN KIT  
SECTION 2.C.  
HEARTH  
CLEAR SPACE  
SECTION 2.D.  
GRATE  
SECTION 3.C.  
Figure 2.1 General Operating Parts  
10  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Fan Kit (optional)  
G. Remote Controls, Wall Controls and Wall  
Switches  
If desired, a fan kit may be added. Contact your dealer to  
order the correct fan kit.  
Follow the instructions supplied with the control installed  
to operate your fireplace:  
D. Clear Space  
For safety:  
WARNING! DO NOT place combustible objects in front  
of the fireplace or block louvers. High temperatures may  
start a fire. See Figure 2.2.  
• Install a switch lock or a wall/remote control with child  
protection lockout feature.  
• Keep remote controls out of reach of children.  
See your dealer if you have questions.  
Avoid placing candles and other heat-sensitive objects on  
mantel or hearth. Heat may damage these objects.  
Figure 2.2 Clear Space  
E. Decorative Doors and Fronts  
WARNING! Risk of Fire! Install ONLY doors or fronts  
approved by Hearth & Home Technologies. Unapproved  
doors or fronts may cause fireplace to overheat.  
This fireplace has been supplied with an integral  
barrier to prevent direct contact with the fixed glass  
panel. DO NOT operate the fireplace with the barrier  
removed.  
Contact your dealer or Hearth & Home Technologies if  
the barrier is not present or help is needed to properly  
install one.  
For more information refer to the instructions supplied with  
your decorative door or front.  
F. Fixed Glass Assembly  
See Section 14.H.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
H. IPI Battery Tray/Battery Installation  
The IntelliFire PlusTM system has a battery backup option.  
Battery longevity and performance will be affected by the  
service temperatures of this appliance.  
NOTICE: Batteries should only be used as a power source  
in the event of an emergency such as an outage.  
SELECTOR  
SWITCH  
I. Control Module Operation  
1. The control module has an ON/OFF/REMOTE selector  
switch that must be set. See Figure 2.3.  
OFF Position: Appliance will ignore all power  
inputs and will not respond to any commands from  
a wall switch or remote. The unit should be in the  
OFF position during installation, service, battery  
installation, and in the event that the control goes  
into LOCK-OUT mode as a result of an error code.  
STATUS INDICATOR LED  
FLAME HI/LO SWITCH  
NG/LP SETTING  
(RC100 OR WIRED WALL SWITCH ONLY)  
Figure 2.3 Control Module  
ON Position: Appliance will ignite and run  
continuously in the HI flame setting, with no  
adjustment in flame output. This mode of operation  
is primarily used for initial installation or power  
outage operation with battery backup.  
•
•
•
Locate the module selector switch. (SeeFigure 2.3).  
Set the module selector switch to the OFF position.  
Wait five (5) minutes to allow possible accumulated gas  
to clear.  
REMOTE Position:  
Appliance will initiate  
commands from an optional wired wall switch and/  
or the wireless remote (RC300).  
•
Set the module selector switch to the ON or REMOTE  
position.  
2. If using a wired wall switch with the module in REMOTE  
mode, the flame output can be adjusted with the HI/  
LO selector switch on the module. See Figure 2.3.  
Note that the flame HI/LO selector switch will become  
inactive once an optional remote control (RC200/  
RC300) is programmed to the control module. Note  
that the control module will always ignite the fireplace  
on HI and remain so for the initial 10 seconds of  
operation. If the HI/LO is switched to the LO position,  
the flame output will automatically drop to the lowest  
setting after the flame has been established for 10 sec.  
After this 10 second period, the flame can be adjusted  
from HI to LO with the switch.  
•
Start the appliance.  
WARNING! Risk of Explosion! DO NOT reset the mod-  
ule more than one time within a five minute time period.  
Gas may accumulate in firebox. Call a qualified service  
technician.  
Nine Hour Safety Shutdown Feature  
This appliance has a safety feature that automatically  
shuts down the fireplace after 9 hours of continuous  
operation without receiving a command from the  
remote.  
3. Thecontrolmodulehassafetyfeaturethatautomatically  
shuts down the fireplace after 9 hours of continuous  
operation without receiving a command from the  
remote.  
J. Before Lighting Fireplace  
Before operating this fireplace for the first time, have a  
qualified service technician:  
• Verify all shipping materials have been removed from  
inside and/or underneath the firebox.  
4. If you intend to use both a wired wall switch and the  
RC300 remote control to operate your fireplace, the  
wall switch will override any commands given by the  
remote.  
• Review proper placement of logs, ember material and/  
or other decorative materials.  
• Ensure plastic finishing strips have been removed after  
use for incorporating finishing materials.  
5. Module Reset  
This module may lock-out under certain conditions.  
When this occurs, the appliance will not ignite or  
respond to commands. The module will go into  
lock-out mode by emitting three audible beeps, then  
continuously displaying a RED/GREEN error code at  
its status indicator LED.  
• Check the wiring.  
• Check the air shutter adjustment.  
• Ensure that there are no gas leaks.  
• Ensure that the glass is sealed and in the proper position  
and that the integral barrier is in place.  
•
Check battery tray. Remove batteries if installed.  
Batteries should only be installed for use during power  
outages. See Section H.  
WARNING! Risk of Fire or Asphyxiation! DO NOT op-  
erate fireplace with fixed glass assembly removed.  
12  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K. Lighting Instructions (IPI)  
FOR YOUR SAFETY  
LIGHTING  
READ BEFORE LIGHTING  
INSTRUCTIONS (IPI)  
WARNING: If you do not follow these instructions exactly, a fire or explosion  
may result causing property damage, personal injury or loss of life.  
1. This appliance is equipped with an ignition  
device which automatically lights the burner.  
DO NOT try to light the burner by hand.  
• Immediately call your gas supplier  
from a neighbor’s phone. Follow the  
gas supplier’s instructions.  
A. This appliance is equipped with an  
intermittent pilot ignition (IPI) device  
which automatically lights the burn-  
er. DO NOT try to light the burner by  
hand.  
GAS  
VALVE  
• If you cannot reach your gas sup-  
plier, call the fire department.  
B. BEFORE LIGHTING, smell all around  
the appliance area for gas. Be sure to  
smell next to the floor because some  
gas is heavier than air and will settle  
on the floor.  
C. DO NOT use this appliance if any  
part has been under water. Imme-  
diately call a qualified service tech-  
nician to inspect the appliance and  
to replace any part of the control  
system and any gas control which  
has been under water.  
2. Wait five (5) minutes to clear out any gas.  
Then smell for gas, including near the floor. If  
you smell gas, STOP! Follow “B” in the Safety  
Information located on the left side of this la-  
bel. If you do not smell gas, go to next step.  
WHAT TO DO IF YOU SMELL GAS  
• DO NOT try to light any appliance.  
3. To light the burner:  
• DO NOT touch any electric switch; do  
not use any phone in your building.  
Equipped with wall switch: Turn ON/OFF switch  
to ON.  
Equipped with remote or wall control: Press  
ON or FLAME button.  
WARNING: CAUTION:  
Equipped with thermostat: Set temperature to  
desired setting.  
Hot while in operation. DO NOT touch.  
Keep children, clothing, furniture, gaso-  
line and other liquids having flammable  
vapors away.  
DO NOT CONNECT LINE VOLT-  
AGE (110/120 VAC OR 220/240  
VAC) TO THE CONTROL VALVE.  
4. If the appliance does not light after three tries,  
call your service technician or gas supplier.  
Improper installation, adjustment, al-  
teration, service or maintenance can  
cause injury or property damage. Re-  
fer to the owner’s information manual  
provided with this appliance.  
TO TURN OFF  
GAS TO APPLIANCE  
1. Equipped with wall switch: Turn ON/OFF switch  
DO NOT operate the appliance with  
fixed glass assembly removed, cracked  
or broken. Replacement of the fixed  
glass assembly should be done by a  
licensed or qualified service person.  
to OFF.  
This appliance needs fresh air for  
safe operation and must be installed  
so there are provisions for adequate  
combustion and ventilation air.  
Equipped with remote or wall control: Press  
OFF button.  
NOT FOR USE  
WITH SOLID FUEL  
Equipped with thermostat: Set temperature to  
lowest setting.  
If not installed, operated, and main- For use with natural gas and propane.  
tained in accordance with the manufac- A conversion kit, as supplied by the  
turer’s instructions, this product could manufacturer, shall be used to convert  
expose you to substances in fuel or this appliance to the alternate fuel.  
2. Service technician should turn off electric  
power to the control when performing service.  
fuel combustion which are known to the  
State of California to cause cancer, birth  
Also Certified for Installation in a  
Bedroom or a Bedsitting Room.  
593-913G  
defects, or other reproductive harm.  
For assistance or additional informa-  
Keep burner and control compartment  
tion, consult a qualified installer, ser-  
clean. See installation and operating  
vice agency or the gas supplier.  
instructions accompanying appliance.  
For additional information on operating your  
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.  
Final inspection by  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
L. Lighting Instructions (Standing Pilot)  
LIGHTING  
INSTRUCTIONS  
1. Open control access panel.  
FOR YOUR SAFETY  
READ BEFORE LIGHTING  
WARNING: If you do not follow these instructions exactly, a fire or explosion  
may result causing property damage, personal injury or loss of life.  
2. Turn off all electric power to  
the appliance.  
3. Push in gas control knob  
slightly and turn clockwise  
to “OFF”.  
• If you cannot reach your gas sup-  
plier, call the fire department.  
A. This appliance has a pilot which  
must be lighted by hand. When  
lighting the pilot, follow these in-  
structions exactly.  
C. Use only your hand to push in or  
turn the gas control knob. Never use  
tools. If the knob will not push in or  
turn by hand, DO NOT try to repair  
it, call a qualified service technician.  
Force or attempted repair may re-  
sult in a fire or explosion.  
Note: Knob cannot be turned from “PILOT” to “OFF”  
unless knob is pushed in slightly. DO NOT force.  
B. BEFORE LIGHTING, smell all around  
the appliance area for gas. Be sure to  
smell next to the floor because some  
gas is heavier than air and will settle  
on the floor.  
4. Open the fixed glass assembly. You may need to  
remove the decorative front.  
5. Wait five (5) minutes to clear out any gas. Then  
smell for gas, including near the floor. If you smell  
gas, STOP! Follow “B” in the Safety  
Information located on the left side  
of this label. If you don’t smell gas,  
go to next step.  
D. DO NOT use this appliance if any  
part has been under water. Imme-  
diately call a qualified service tech-  
nician to inspect the appliance and  
to replace any part of the control  
system and any gas control which  
has been under water.  
WHAT TO DO IF YOU SMELL GAS  
• DO NOT try to light any appliance.  
• DO NOT touch any electric switch; do  
not use any phone in your building.  
6. Find the pilot. The pilot is inside  
combustion chamber next to the  
main burner  
• Immediately call your gas supplier  
from a neighbor’s phone. Follow the  
gas supplier’s instructions.  
7. Turn knob on gas control counterclockwise  
to “PILOT”.  
8. Push in control knob all the way and hold in. Immedi-  
ately depress red or black piezo button. It may require  
several depressions of the red or black piezo button  
until PILOT lights. If PILOT light does not light after  
10 seconds, return to step 3. Continue to hold the  
control knob in for about one minute after the pilot is  
lit. Release knob and it will pop back out. Pilot should  
remain lit. If it goes out, repeat steps 3 through 6.  
WARNING: CAUTION:  
Hot while in operation. DO NOT touch.  
DO NOT CONNECT 110 VAC TO  
Keep children, clothing, furniture, gaso-  
THE CONTROL VALVE.  
line and other liquids having flammable  
Improper installation, adjustment, al-  
vapors away.  
• If knob does not pop up when released, stop and  
immediately call your service technician or gas  
supplier.  
teration, service or maintenance can  
DO NOT operate the appliance with  
fixed glass assembly removed, cracked  
or broken. Replacement of the fixed  
glass assembly should be done by a  
licensed or qualified service person.  
cause injury or property damage. Re-  
fer to the owner’s information manual  
provided with this appliance.  
• If the pilot will not stay lit after several tries, turn  
the gas control knob to “OFF” and call your ser-  
vice technician or gas supplier.  
This appliance needs fresh air for  
safe operation and must be installed  
so there are provisions for adequate  
combustion and ventilation air.  
9. Reinstall fixed glass assembly. Reinstall decorative  
front.  
NOT FOR USE  
WITH SOLID FUEL  
10. Turn gas control knob counterclockwise  
to “ON”. Close access panel.  
If not installed, operated, and main-  
tained in accordance with the man-  
ufacturer’s instructions, this product  
could expose you to substances in fuel  
or fuel combustion which are known to  
the State of California to cause can-  
cer, birth defects, or other reproductive  
harm.  
For use with natural gas and propane.  
A conversion kit, as supplied by the  
manufacturer, shall be used to convert  
this appliance to the alternate fuel.  
11. Turn on all electric power to the appliance.  
12. To light burner, turn the wall control or on/off switch  
to “ON”.  
TO TURN OFF  
GAS TO APPLIANCE  
1. Turn off all electric power to the appliance if ser-  
Also Certified for Installation in a  
Bedroom or a Bedsitting Room.  
For assistance or additional informa-  
tion, consult a qualified installer, ser-  
vice agency or the gas supplier.  
Keep burner and control compartment  
clean. See installation and operating  
instructions accompanying appliance.  
vice is to be performed.  
2. Open control access panel.  
3. Move switch to “OFF” position.  
For additional information on operating your  
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.  
4. Push in gas control knob slightly and turn clock-  
wise  
to OFF”. DO NOT force.  
5. Close control access panel.  
Final inspection by  
464-903H  
14  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M. After Fireplace is Lit  
Initial Break-in Procedure  
• The fireplace should be run three to four hours  
continuously on high.  
• Turn the fireplace off and allow it to completely cool.  
• Remove fixed glass assembly. See Section 14.H.  
• Clean fixed glass assembly. See Section 3.  
• Replace the fixed glass assembly and run continuously  
on high an additional 12 hours.  
This cures the materials used to manufacture the fire-  
place.  
NOTICE! Open windows for air circulation during fire-  
place break-in.  
• Some people may be sensitive to smoke and odors.  
• Smoke detectors may activate.  
N. Frequently Asked Questions  
ISSUE  
SOLUTIONS  
This is a result of gas combustion and temperature variations. As the appliance warms, this  
condensation will disappear.  
Condensation on the glass  
Blue flames  
This is a result of normal operation and the flames will begin to yellow as the appliance is al-  
lowed to burn for 20 to 40 minutes.  
When first operated, this appliance may release an odor for the first several hours. This is caused  
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may  
also be released from finishing materials and adhesives used around the appliance.  
Odor from appliance  
Film on the glass  
This is a normal result of the curing process of the paint and logs. Glass should be cleaned  
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing  
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See  
your dealer.  
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to  
the sound produced by a furnace or heating duct. This noise does not affect the operation or  
longevity of the appliance.  
Metallic noise  
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is  
turned off. Some optional control systems available with IPI models may allow pilot flame to  
remain lit. In a standing pilot system the pilot will always stay on.  
Is it normal to see the pilot flame burn  
continually?  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Maintenance and Service  
3
Doors, Surrounds, Fronts  
Any safety screen or guard removed for servicing must be  
replaced prior to operating the fireplace.  
Frequency: Annually  
By: Homeowner  
When properly maintained, your fireplace will give you  
many years of trouble-free service. We recommend an-  
nual service by a qualified service technician.  
Tools needed: Protective gloves, stable work surface  
• Assess condition of screen and replace as necessary.  
A. Maintenance Tasks-Homeowner  
• Inspect for scratches, dents or other damage and repair  
as necessary.  
Installation and repair should be done by a qualified service  
technician only. The fireplace should be inspected before  
use and at least annually by a professional service person.  
• Check that louvers are not blocked.  
• Vacuum and dust surfaces.  
The following tasks may be performed annually by the  
homeowner. If you are uncomfortable performing any of  
the listed tasks, please call your dealer for a service ap-  
pointment.  
Remote Control  
Frequency: Seasonally  
By: Homeowner  
More frequent cleaning may be required due to lint from  
carpeting or other factors. Control compartment, burner  
and circulating air passageway of the fireplace must be  
kept clean.  
Tools needed: Replacement batteries and remote con-  
trol instructions.  
• Locate remote control transmitter and receiver.  
• Verify operation of remote. Refer to remote control  
operation instructions for proper calibration and setup  
procedure.  
CAUTION! Risk of Burns! The fireplace should be turned  
off and cooled before servicing.  
Glass Cleaning  
Frequency: Seasonally  
By: Homeowner  
• Place batteries as needed in remote transmitters and  
battery-powered receivers.  
• Place remote control out of reach of children.  
Tools Needed: Protective gloves, glass cleaner, drop  
cloth and a stable work surface.  
If not using your fireplace for an extended period of time  
(summer months, vacations/trips, etc), to prevent unin-  
tended operation:  
CAUTION! Handle fixed glass assembly with care.  
Glass is breakable.  
• Avoid striking, scratching or slamming glass  
• Avoid abrasive cleaners  
• Remove batteries from remote controls.  
• Unplug 6 volt transformer plug on IPI models.  
• DO NOT clean glass while it is hot  
• Unplug battery backup from control module.  
• Prepare a work area large enough to accommodate fixed  
glass assembly and door frame by placing a drop cloth  
on a flat, stable surface.  
Note: Fixed glass assembly and gasketing may have res-  
idue that can stain carpeting or floor surfaces.  
• Remove door or decorative front from fireplace and set  
aside on work surface.  
• See Section 14.H for instructions to remove fixed glass  
assembly.  
• Clean glass with a non-abrasive commercially available  
cleaner.  
- Light deposits: Use a soft cloth with soap and water  
- Heavy deposits: Use commercial fireplace glass  
cleaner (consult with your dealer)  
• Carefully set fixed glass assembly in place on fireplace.  
Hold glass in place with one hand and secure glass  
latches with the other hand.  
• Reinstall door or decorative front.  
16  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Replace fireplace if firebox has been perforated.  
Venting  
Frequency: Seasonally  
By: Homeowner  
Control Compartment and Firebox Top  
Frequency: Annually  
Tools needed: Protective gloves and safety glasses.  
By: Qualified Service Technician  
• Inspect venting and termination cap for blockage or  
obstruction such plants, bird nests, leaves, snow, debris,  
etc.  
Tools needed: Protective gloves, vacuum cleaner, dust  
cloths  
• Vacuum and wipe out dust, cobwebs, debris or pet hair.  
Use caution when cleaning these areas. Screw tips that  
have penetrated the sheet metal are sharp and should  
be avoided.  
• Verify termination cap clearance to subsequent construc-  
tion (building additions, decks, fences, or sheds). See  
Section 6.  
• Inspect for corrosion or separation.  
• Remove all foreign objects.  
• Verify weather stripping, sealing and flashing remains  
intact.  
• Verify unobstructed air circulation.  
Burner Ignition and Operation  
Frequency: Annually  
• Inspect draft shield to verify it is not damaged or missing.  
B. Maintenance Tasks-Qualified Service  
Technician  
By: Qualified Service Technician  
Tools needed: Protective gloves, vacuum cleaner, whisk  
broom, flashlight, voltmeter, indexed drill bit set, and a  
manometer.  
The following tasks must be performed by a qualified ser-  
vice technician.  
Gasket Seal and Glass Assembly Inspection  
Frequency: Annually  
• Verify burner is properly secured and aligned with pilot  
or igniter.  
• Clean off burner top, inspect for plugged ports, corrosion  
or deterioration. Replace burner if necessary.  
By: Qualified Service Technician  
Tools needed: Protective gloves, drop cloth and a stable  
work surface.  
• Replace Glowing embers with new dime-size pieces.  
DO NOT block ports or obstruct lighting paths. Refer to  
Section 14 for proper ember placement.  
• Inspect gasket seal and its condition.  
• Inspect fixed glass assembly for scratches and nicks that  
can lead to breakage when exposed to heat.  
• Verify batteries have been removed from battery back-  
up IPI systems to prevent premature battery failure or  
leaking.  
• Confirm there is no damage to glass or glass frame.  
Replace as necessary.  
• Check for smooth lighting and ignition carryover to all  
ports. Verify that there is no ignition delay.  
• Verify that fixed glass assembly is properly retained and  
attachment components are intact and not damaged.  
Replace as necessary.  
• Inspect for lifting or other flame problems.  
• Verify air shutter setting is correct. See Section 14 for  
required air shutter setting. Verify air shutter is clear of  
dust and debris.  
Logs  
Frequency: Annually  
• Inspect orifice for soot, dirt and corrosion. Verify orifice  
size is correct. See Service Parts List for proper orifice  
sizing.  
By: Qualified Service Technician  
Tools needed: Protective gloves.  
• Verify manifold and inlet pressures. Adjust regulator as  
required.  
• Inspect for damaged or missing logs. Replace as neces-  
sary. Refer to Section 14 for log placement instructions.  
• Inspect pilot flame pattern and strength. See Figures 3.1  
and 3.2 for proper pilot flame pattern. Clean or replace  
orifice spud as necessary.  
• Verify correct log placement and no flame impingement  
causing sooting. Correct as necessary.  
Firebox  
• Inspect thermocouple/thermopile or IPI flame sensing  
rod for soot, corrosion and deterioration. Polish with fine  
steel wool or replace as required.  
Frequency: Annually  
By: Qualified Service Technician  
Tools needed: Protective gloves, sandpaper, steel wool,  
cloths, mineral spirits, primer and touch-up paint.  
• Verify thermocouple/thermopile millivolt output. Replace  
pilot as necessary. (Standing pilot only)  
• Inspect for paint condition, warped surfaces, corrosion  
or perforation. Sand and repaint as necessary.  
• Verify that there is not a short in flame sense circuit  
by checking continuity between pilot hood and flame  
sensing rod. Replace pilot as necessary. (IPI only)  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Figure 3.1 IPI Pilot Flame Patterns  
Figure 3.3 Grate Removal  
Note: The base refractory must be  
removed to access screws.  
BASE REFRACTORY  
Figure 3.2 Standing Pilot Flame Patterns  
C. Refractory, Grate and Valve Assembly  
Removal  
It may become necessary to remove the refractory, grate  
and valve assemblies. This task should be performed by  
a qualified service technician. The grate and base refrac-  
tory do not need to be removed to service the burner  
assembly.  
Figure 3.4 Base Refractory Removal  
18  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 3.5 Valve Assembly Removal  
D. Burner Identification/Verification  
The burner may be accessed for identification and verification purposes. This task should be performed by a qualified ser-  
vice technician. The base refractory, valve plate and grate do not need to be removed to access the burner assembly. The  
logs and fiber burner top need to be removed to access the burner. Disconnect the pilot from the burner before removal.  
See Figure 3.6 for burner identification chart. Notch patterns are located on bottom side of burner.  
NOTCH LOCATION  
NG  
LP  
6000C  
6000CL  
6000CLX  
6000CBV  
8000C  
8000CL  
8000CLX  
8000CBV  
Figure 3.6 Burner Identification  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installer Guide  
Getting Started  
4
A. Typical Appliance System  
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not  
drawn to scale. Actual product may vary from pictures in manual  
HORIZONTAL  
TERMINATION CAP  
(SECTION 10.L)  
Note: Dual venting configurations  
ARE NOT allowed. Appliance MUST  
be vented EITHER vertically OR  
horizontally.  
VERTICAL TERMINATION CAP  
(SECTION 10.I)  
NON-COMBUSTIBLE ROOF FLASHING  
MAINTAINS MINIMUM CLEARANCE  
AROUND PIPE (SECTION 10.G)  
STORM COLLAR  
(SECTION 10.H)  
VENT PIPE PENETRATES ROOF  
PREFERABLY WITHOUT AFFECTING  
ROOF RAFTERS (SECTION 8.C)  
ATTIC INSULATION SHIELD (NOT  
VENT PIPE (SECTIONS 7 and 8)  
SHOWN) MUST BE USED HERE TO  
KEEP INSULATION AWAY FROM  
VENT PIPE IF ATTIC IS INSULATED  
(SECTION 8.D)  
CEILING FIRESTOP  
ON FLOOR OF ATTIC  
(SECTION 8.C)  
FRAMING/HEADER  
(SECTION 5.B)  
FRAMING HEADED OFF  
IN CEILING JOISTS  
(SECTION 8.C)  
OPTIONAL  
WALL SWITCH  
MANTEL AND  
MANTEL LEG  
(SECTION 5.D)  
SURROUND  
HEARTH EXTENSION  
GAS LINE  
(SECTION 11)  
Figure 4.1 Typical System  
20  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Design and Installation Considerations  
D. Inspect Appliance and Components  
Heat & Glo direct vent gas appliances are designed to  
operate with all combustion air siphoned from outside of  
the building and all exhaust gases expelled to the outside.  
No additional outside air source is required.  
• Carefully remove the appliance and components from  
the packaging.  
• The vent system components and decorative doors and  
fronts may be shipped in separate packages.  
Installation MUST comply with local, regional, state and  
national codes and regulations. Consult insurance carrier,  
local building inspector, fire officials or authorities having  
jurisdiction over restrictions, installation inspection and  
permits.  
• If packaged separately, the log set and appliance grate  
must be installed.  
• Report to your dealer any parts damaged in shipment,  
particularly the condition of the glass.  
• Read all of the instructions before starting the instal-  
lation. Follow these instructions carefully during the  
installation to ensure maximum safety and benefit.  
Before installing, determine the following:  
• Where the appliance is to be installed.  
• The vent system configuration to be used.  
• Gas supply piping requirements.  
• Electrical wiring requirements.  
WARNING! Risk of Fire or Explosion! Damaged parts  
could impair safe operation. DO NOT install damaged, in-  
complete or substitute components. Keep appliance dry.  
• Framing and finishing details.  
Hearth & Home Technologies disclaims any responsibility for,  
and the warranty will be voided by, the following actions:  
• Whether optional accessories—devices such as a fan,  
wall switch, or remote control—are desired.  
• Installation and use of any damaged appliance or vent  
system component.  
Improper installation, adjustment, alteration, service or  
maintenance can cause injury or property damage. For  
assistance or additional information, consult a qualified  
service technician, service agency or your dealer.  
• Modification of the appliance or vent system.  
• Installation other than as instructed by Hearth & Home  
Technologies.  
• Improper positioning of the gas logs or the glass door.  
• Installation and/or use of any component part not approved  
by Hearth & Home Technologies.  
C. Tools and Supplies Needed  
Before beginning the installation be sure that the following  
tools and building supplies are available.  
Any such action may cause a fire hazard.  
Tape measure  
Framing material  
WARNING! Risk of Fire, Explosion or Electric Shock!  
DO NOT use this appliance if any part has been under  
water. Call a qualified service technician to inspect the  
appliance and to replace any part of the control system  
and/or gas control which has been under water.  
Pliers  
Hammer  
Non-corrosive leak check solution-  
Phillips screwdriver  
Gloves  
Framing square  
Voltmeter  
Plumb line  
Level  
Electric drill and bits (1/4 in.)  
Safety glasses  
Reciprocating saw  
Flat blade screwdriver  
Manometer  
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws  
Caulking material (300ºF minimum continuous exposure  
rating)  
One 1/4 in. female connection (for optional fan).  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Framing and Clearances  
5
NOTICE: Illustrations reflect typical installations and are  
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams  
are not drawn to scale. Actual installation may vary due to  
individual design preference.  
A. Selecting Appliance Location  
When selecting a location for the appliance it is important to  
consider the required clearances to walls (see Figure 5.1).  
WARNING! Risk of Fire or Burns! Provide adequate  
clearance around air openings and for service access.  
Due to high temperatures, the appliance should be locat-  
ed out of traffic and away from furniture and draperies.  
NOTE: THE REAR STANDOFF MAY NEED  
TO BE REMOVED WHEN VENTING AT 45º  
A
G
1/2 IN.  
B
ALCOVE  
INSTALLATION  
E
A
B
C
TOP VENT  
ONE 90º ELBOW  
REAR VENT,  
HORIZONTAL TERMINATION  
TWO ELBOWS  
REAR VENT  
ONE ELBOW  
REAR VENT  
NO ELBOWS  
B
B
B
D
D
F
D
H
D
A
B
42  
C
72  
D
E
F
G
H
8
in.  
51  
56-5/8  
1438  
22  
17-3/4  
451  
See Section D.  
Mantel Projections  
6000  
8000  
mm  
in.  
1295  
55-7/8  
1419  
1067  
49  
1829  
79  
559  
22  
203  
10  
61-1/2  
1562  
19-3/4  
502  
See Section D.  
Mantel Projections  
mm  
1245  
2007  
559  
254  
Figure 5.1 Appliance Locations - 6000 Models  
22  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
stops should be caulked with caulk with a minimum of  
300ºF continuous exposure rating to seal gaps. Gas line  
holes and other openings should be caulked with caulk  
with a minimum of 300ºF continuous exposure rating or  
stuffed with unfaced insulation. If the appliance is being  
installed on a cement surface, a layer of plywood may be  
placed underneath to prevent conducting cold up into the  
room.  
B. Constructing the Appliance Chase  
A chase is a vertical box-like structure built to enclose the  
gas appliance and/or its vent system. In cooler climates  
the vent should be enclosed inside the chase.  
NOTICE: Treatment of ceiling firestops and wall shield  
firestops and construction of the chase may vary with the  
type of building. These instructions are not substitutes  
for the requirements of local building codes. Therefore,  
you MUST check local building codes to determine the  
requirements to these steps.  
C. Clearances  
NOTICE: Install appliance on hard metal or wood surfaces  
extending full width and depth. DO NOT install directly  
on carpeting, vinyl, tile or any combustible material other  
than wood.  
Chases should be constructed in the manner of all out-  
side walls of the home to prevent cold air drafting prob-  
lems. The chase should not break the outside building  
envelope in any manner.  
WARNING! Risk of Fire! Maintain specified air space  
clearances to appliance and vent pipe:  
Walls, ceiling, base plate and cantilever floor of the chase  
should be insulated. Vapor and air infiltration barriers  
should be installed in the chase as per regional codes for  
the rest of the home. Additionally, in regions where cold  
air infiltration may be an issue, the inside surfaces may be  
sheetrocked and taped for maximum air tightness.  
• Insulation and other materials must be secured to prevent  
accidental contact.  
• The chase must be properly blocked to prevent blown  
insulation or other combustibles from entering and  
making contact with fireplace or chimney.  
To further prevent drafts, the wall shield and ceiling fire-  
• Failure to maintain airspace may cause overheating and  
a fire.  
A
E
B
J
F
H
C
D
I
G
* MINIMUM FRAMING DIMENSIONS  
A
B
C**  
D
E
F
G
H
I
J
Rough  
Opening Opening  
(Width)  
Rough  
Rough  
Opening Opening  
(Depth)  
Rough  
Models  
Clearance Combustible Combustible Behind  
Sides of  
Front of  
to Ceiling  
Floor  
Flooring  
Appliance Appliance Appliance  
(Height)  
40-1/8  
1019  
(Width)  
in.  
mm  
in.  
10  
22  
42  
25  
635  
25  
0
0
0
0
0
0
0
0
1/2  
13  
1/2  
13  
36  
914  
36  
6000  
8000  
254  
10  
559  
22  
1067  
49  
42-1/8  
1019  
1/2  
13  
1/2  
13  
mm  
254  
559  
1245  
635  
914  
* Adjust framing dimensions for interior sheathing (such as sheetrock)  
C** Add 12 inches for rear venting with one 90º elbow.  
Figure 5.2 Clearances to Combustibles  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Combustible Mantel Legs or Wall Projections  
D. Mantel and Wall Projections  
WARNING! Risk of Fire! Comply with all minimum clear-  
ances as specified. Framing or finishing material closer than  
theminimumslistedmustbeconstructedentirelyofnoncom-  
bustible materials (i.e., steel studs, concrete board, etc).  
INTERIOR WALL  
TOP VIEW  
Combustible Mantels  
TO CEILING  
18  
A
B
12  
11  
FIREPLACE OPENING  
10  
32  
9
8
25  
7
MANTEL LEG OR WALL PROJECTIONS  
19  
6
18  
5
17  
If A minimum is ____, then B maximum is_____.  
4
16  
3
15  
Inches  
Millimeters  
Inches  
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16  
A
14  
62  
1
87  
2
113  
3
138  
4
164  
5
189  
∞
∞
13  
B
12  
Millimeters  
25  
51  
76  
102  
127  
2-1/2  
11  
10  
Figure 5.4 Clearances to Mantel Legs or Wall Projections  
(Acceptable on both sides of opening.)  
5
MEASUREMENTS FROM  
TOP EDGE OF THE OPENING  
Note: All measurements in inches.  
Note: Measurement is taken from top of the  
opening, NOT the top of the fireplace.  
Figure 5.3 Minimum Vertical and Maximum Horizontal  
Dimensions of Combustibles  
24  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Termination Locations  
6
A. Vent Termination Minimum Clearances  
A
B
6 in. (minimum) up to 20 in.  
152 mm/508 mm  
18 in. minimum  
457 mm  
WARNING  
20 in. and over  
0 in. minimum  
Fire Risk.  
Gas, Wood or Fuel Oil  
Termination Cap  
Maintain vent clearance to combustibles as  
specified.  
• DO NOT pack air space with insulation or other  
materials.  
B
Failure to keep insulation or other materials away  
from vent pipe may cause overheating and fire.  
A *  
HORIZONTAL  
OVERHANG  
Gas  
Termination  
Cap **  
2 FT.  
20 INCHES MIN.  
VERTICAL  
MIN.  
WALL  
LOWEST  
DISCHARGE  
OPENING  
GAS DIRECT VENT  
TERMINATION CAP  
X
12  
*
If using decorative cap cover(s), this distance may need to be  
increased. Refer to the installation instructions supplied with the  
decorative cap cover.  
ROOF PITCH  
IS X/ 12  
In a staggered installation with both gas and wood or fuel oil  
terminations, the wood or fuel oil termination cap must be  
higher than the gas termination cap.  
**  
H (MIN.) - MINIMUM HEIGHT FROM ROOF  
TO LOWEST DISCHARGE OPENING  
Figure 6.2 Staggered Termination Caps  
Roof Pitch  
H (Min.) Ft.  
Flat to 6/12...........................................................1.0*  
Over 6/12 to 7/12.................................................1.25*  
Over 7/12 to 8/12.................................................1.5*  
Over 8/12 to 9/12.................................................2.0*  
Over 9/12 to 10/12...............................................2.5  
Over 10/12 to 11/12.............................................3.25  
Over 11/12 to 12/12.............................................4.0  
Over 12/12 to 14/12.............................................5.0  
Over 14/12 to 16/12.............................................6.0  
Over 16/12 to 18/12.............................................7.0  
Over 18/12 to 20/12.............................................7.5  
Over 20/12 to 21/12.............................................8.0  
* 3 foot minimum in snow regions  
Figure 6.1 Minimum Height From Roof To Lowest Discharge  
Opening  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
O
N
P
R
F
C
V
Q
B
J
H or i  
B
V
B
V
V
E
X
D
V
V
G
H
M
V
V
V
V
L
H
V
A
A
K
K
Electrical  
Service  
V
V
V
X
= VENT TERMINAL  
C
V
= AIR SUPPLY INLET  
= AREA WHERE TERMINAL IS NOT PERMITTED  
A
= 12 inches.................clearances above grade, veranda,  
porch, deck or balcony  
Covered Alcove Applications  
(Spaces open only on one side and with an overhang)  
B
= 12 inches.................clearance to window or door that may  
be opened, or to permanently closed  
window  
N
= 6 inches ........... non-vinyl sidewalls  
12 inches ......... vinyl sidewalls  
= 18 inches ......... non-vinyl soffit and overhang  
42 inches ......... vinyl soffit and overhang  
= 8 ft.  
O
P
C
= 18 inches.................clearance below unventilated soffit  
18 inches.................clearance below ventilated soffit  
30 inches................clearance below vinyl soffits and  
electrical service  
QMIN  
3 feet  
6 feet  
9 feet  
12 feet  
RMAX  
D
E
F
= 9 inches...................clearance to outside corner  
= 6 inches...................clearance to inside corner  
1 cap  
2 caps  
3 caps  
4 caps  
2 x Q ACTUAL  
1 x Q ACTUAL  
2/3 x Q ACTUAL  
1/2 x Q ACTUAL  
= 3 ft. (Canada)..........not to be installed above a gas me-  
ter/regulator assembly within 3 feet  
horizontally from the center-line of the  
regulator  
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL  
G
= 3 ft...........................clearance to gas service regulator  
vent outlet  
Measure vertical clearances from this surface.  
H
= 9 inches (U.S.A)  
12 inches (Canada).clearancetonon-mechanical(unpow-  
ered) air supply inlet, combustion air  
inlet or direct-vent termination  
i
= 3 ft. (U.S.A.)  
6 ft. (Canada)...........clearance to a mechanical (powered)  
air supply inlet  
All mechanical air intakes within 10 feet of a termination cap  
must be a minimum of 3 feet below termination.  
J
= 7 ft.......................... On public property: clearance above  
paved sidewalk or a paved driveway.  
A vent shall not terminate directly above a sidewalk or paved  
driveway which is located between two single family dwellings  
and serves both dwellings.  
Measure horizontal clearances from this surface.  
CAUTION! Risk of Burns! Termination caps are HOT,  
consider proximity to doors, traffic areas or where people  
may pass or gather (sidewalk, deck, patio, etc.). Listed cap  
shields available. Contact your dealer.  
K
L
=
6 inches.................clearance from sides of electrical  
service  
= 12 inches................clearance above electrical service  
•
•
•
•
Local codes or regulations may require different  
clearances.  
Location of the vent termination must not interfere with access to the  
electrical service.  
Vent system termination is NOT permitted in screened  
porches.  
Vent system termination is permitted in porch areas with  
two or more sides open.  
M
= 18 inches....................clearanceunderveranda,porch,deck,  
balcony or overhang  
42 inches ................vinyl or composite overhang  
Permitted when veranda, porch, deck or balcony is fully open  
on a minimum of 2 sides beneath the floor.  
Hearth & Home Technologies assumes no responsibility  
for the improper performance of the appliance when the  
venting system does not meet these requirements.  
Vinyl protection kits are suggested for use with vinyl siding.  
Figure 6.3 Minimum Clearances for Termination  
•
26  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Vent Information and Diagrams  
7
A. Approved Pipe  
This appliance is approved for use with Hearth & Home  
Technologies DVP or SLP venting systems. Refer to Sec-  
tion 16B for vent component information.  
DO NOT mix pipe, fittings or joining methods from differ-  
ent manufacturers.  
Vertical  
The pipe is tested to be run inside an enclosed wall.  
There is no requirement for inspection openings at each  
joint within the wall.  
8-1/2 in.  
WARNING! Risk of Fire or Asphyxiation. This appli-  
ance requires a separate vent. DO NOT vent to a pipe  
serving a separate solid fuel burning appliance.  
B. Vent Table Key  
Horizontal  
The abbreviations listed in this vent table key are used in  
the vent diagrams.  
Figure 7.1  
Symbol  
Description  
D. Measuring Standards  
First section (closest to appliance) of vertical length  
V1  
Vertical and horizontal measurements listed in the vent  
diagrams were made using the following standards.  
Second section of vertical length  
V2  
H1  
H2  
First section (closest to appliance) of horizontal length  
Subsequent sections of horizontal length  
• Pipe measurements are shown using the effective length  
of pipe (see Figure 7.2).  
• Horizontal terminations are measured to the outside  
mounting surface (flange of termination cap) (see Figure  
6.3).  
C. Use of Elbows  
• Vertical terminations are measured to bottom of  
termination cap.  
Diagonal runs have both vertical and horizontal vent as-  
pects when calculating the effects. Use the rise for the  
vertical aspect and the run for the horizontal aspect (see  
Figure 7.1).  
• Horizontal pipe installed level with no rise.  
Two 45º elbows may be used in place of one 90º elbow.  
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216  
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A  
length of straight pipe is allowed between two 45º elbows  
(see Figure 7.1).  
Effective Length  
Pipe  
Inches  
4
Millimeters  
102  
DVP4  
DVP6  
6
12  
152  
305  
Effective  
Height/Length  
DVP12  
DVP24  
DVP36  
DVP48  
DVP6A  
24  
610  
36  
914  
48  
1219  
76 to 152  
3 to 6  
DVP12A 3 to 12 76 to 305  
Figure 7.2 DVP Pipe Effective Length  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
E. Vent Diagrams  
Top Vent - Horizontal Termination  
WARNING  
Note: The 6000/8000 series fireplaces can adapt to SLP series  
vent pipe, if desired.  
Fire Risk. Explosion Risk.  
Do NOT pack insulation or other combustibles  
between ceiling firestops.  
When venting off the top of the unit, use a DVP-2SL adapter and a  
minimum 48 inch vertical section of SLP series vent pipe.  
• ALWAYS maintain specified clearances around  
venting and firestop systems.  
A DVP-SLP24 adapter may also be used with a 24 inch vertical  
section of SLP series vent pipe.  
• Install wall shield and ceiling firestops as speci-  
fied.  
After the 48 inch vertical section, the venting table rules must be  
followed. The first 48 inch vertical section is NOT counted as part  
of the vertical components in the table. It is still counted as part of  
the overall maximum run. All venting table rules for the vent run  
must still be followed.  
Failure to keep insulation or other material away  
from vent pipe may cause fire.  
WARNING  
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal  
Fire Risk.  
SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal  
• When using DVP-HRC-SS and DVP-HRC-ZC-  
SS termination caps on top vented fireplaces, a  
6 inch minimum vertical vent section is required  
before installing first elbow.  
Top Vent - Horizontal Termination  
One Elbow  
6000C-IPI  
8000C-IPI  
V1 Minimum  
H1 Maximum  
V1 Minimum  
Elbow Only  
H1 Maximum  
Elbow only  
2 ft  
610 mm  
1.2 m  
1.8 m  
3.0 m  
4.6 m  
6.1 m  
7.6 m  
2 ft.  
610 mm  
914 mm  
1.8 m  
6 in.  
152 mm  
305 mm  
457 mm  
610 m  
4 ft.  
6 ft.  
1 ft.  
305 mm  
610 mm  
914 mm  
1.2 m  
3 ft.  
6 ft.  
1 ft.  
1-1/2 ft.  
2 ft.  
2 ft.  
3 ft.  
4 ft.  
10 ft.  
15 ft.  
20 ft.  
25 ft.  
11 ft.  
20 ft.  
3.4 m  
6.1 m  
2-1/2 ft.  
3 ft.  
762 mm  
914 mm  
V1 + H1 = 40 ft. (12.2 m) Maximum  
H1 = 20 ft. (6.1 m) Maximum  
V1 + H1 = 40 ft. (12.2 m) Maximum  
H1 = 25 ft. (7.6 m) Maximum  
Note: For corner installations: A 6 inch (152  
mm) section of straight pipe may need to  
be attached to the appliance before a 90º  
elbow, to allow the vent pipe to clear the top  
standoffs.  
V1  
H1  
Figure 7.3  
28  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Top Vent - Horizontal Termination - (continued)  
Two Elbows  
6000C-IPI  
8000C-IPI  
H1 + H2 Maximum  
V1 Minimum  
H1 + H2 Maximum  
Not allowed  
V1 Minimum  
Elbow only  
Elbow only  
Not allowed  
Not allowed  
6 in.  
1 ft.  
152 mm  
305 mm  
2 ft.  
610 mm  
1.2 m  
3.4 m  
3.8 m  
6.7 m  
6 in.  
152 mm  
305 mm  
610 mm  
914 mm  
1.2 m  
4 ft.  
11 ft.  
19 ft.  
22 ft.  
1 ft.  
2 ft.  
3 ft.  
4 ft.  
6 ft.  
10 ft.  
2 ft.  
610 mm  
1.2 m  
1.8 m  
2.4 m  
3.6 m  
6.1 m  
1-1/2 ft. 457 mm  
2 ft. 610 mm  
2-1/2 ft. 762 mm  
4 ft.  
6 ft.  
8 ft.  
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum  
H1 + H2 = 22 ft. (6.7 m) Maximum  
V1 = 1 ft. (305 mm) Minimum  
1.8 m  
12 ft.  
20 ft.  
3.0  
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum  
H1 + H2 = 20 ft. (6.0 m) Maximum  
V1 = 1 ft. (305 mm) Minimum  
Note: For corner installations: A 6 inch  
(152 mm) section of straight pipe may  
need to be attached to the appliance  
before a 90º elbow, to allow the vent  
pipe to clear the top standoffs.  
V1  
H2  
H1  
INSTALLED  
HORIZONTALLY  
Figure 7.4  
Three Elbows  
V1 Min.  
H1 Max.  
V2 Min.  
0 mm  
H2 Max.  
305 mm  
Elbow only  
2 ft.  
3 ft  
610 mm  
914 mm  
1.8 m  
0 in.  
6 in.  
1 ft.  
1 ft.  
2 ft.  
6 ft.  
6 in.  
152 mm  
305 mm  
152 mm  
305 mm  
610 mm  
1.8 m  
1 ft.  
2 ft.  
3 ft.  
6 ft.  
610 mm  
914 mm  
11 ft.*  
16 ft *  
3.4 m*  
4.9 m*  
2 ft.  
3 ft.  
610 mm  
914 mm  
10 ft.*  
14 ft.*  
3.1 m*  
4.3 m*  
*H1 + H2 = 20 ft. (6.1 m) Maximum  
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum  
H2  
V2  
V1  
H1  
Figure 7.5  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Top Vent - Vertical Termination  
No Elbow  
Flue Restrictor Instructions  
1. Remove exhaust shield using a 1/4 inch nut driver by  
removing the four screws securing it in place (see Figure  
7.7).  
V1 = 40 ft. Max. (12.4 m)  
V1 = 3 ft. Min. (914 mm)  
Note: If installing a vertical vent/  
termination off the top of the ap-  
pliance, the flue restrictor should  
be used.  
EXHAUST  
SHIELD  
FLUE  
RESTRICTOR  
Figure 7.7  
2. Break the flue restrictor into two pieces. Do this by  
bending the part back and forth until it breaks (see  
Figure 7.8).  
V1  
BREAK  
HERE  
Figure 7.8 Flue Restrictor  
Figure 7.6  
30  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Center the Flue Restrictor on vent and secure in place  
by using two self-tapping screws (see Figure 7.10).  
Top Vent - Vertical Termination (continued)  
3. Match the amount of vertical you have in the system  
with the chart to find the appropriate position to set the  
Flue Restrictor (see Figure 7.9).  
5. Reinstall the Exhaust Shield.  
TOP VENT  
NG  
REAR VENT  
Vertical  
4 ft.  
1
2
3
4 5  
LP  
NG  
LP  
No  
No  
No  
1-1  
2-2  
3-3  
3-4  
3-4  
4-4  
4-4  
4-4  
Restrictor Restrictor Restrictor  
No  
8 ft.  
1-2  
3-2  
3-3  
3-3  
3-4  
3-4  
4-4  
1-1  
2-2  
3-3  
3-3  
3-4  
3-4  
4-4  
Restrictor  
1-2  
SETTING  
15 ft.  
20 ft.  
25 ft.  
30 ft.  
35 ft.  
2-3  
2-3  
3-3  
3-3  
3-4  
1
2
3
4 5  
Figure 7.10  
40 ft.  
Figure 7.9  
Note: If the DVP-2SL or DVP-SLP24 adapter is used with  
SLP pipe, you MUST subtract one number from the table  
above.  
Example: Top vent 40 ft vertical with DVP pipe = 4-4  
Top vent 40 ft vertical with SLP pipe = 3-3  
V1  
Elbow only  
6 in. 152 mm 6 ft.  
H1 Maximum  
V2 V1 + V2 Min.  
Two Elbows  
2 ft. 610 mm  
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1.8 m  
3.4 m  
4.9 m  
6.1 m  
2 ft.  
3 ft.  
4 ft.  
610 mm 11 ft.  
914 mm 16 ft.  
1.2 m  
20 ft.  
V1 + V2 + H1 = 50 ft. (15.2 m) Maximum  
*No specific restrictions on this value EXCEPT  
V2  
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)  
V1  
H1  
Figure 7.11  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Top Vent - Vertical Termination - (continued)  
V1  
H1 + H2  
V2  
*
V1 + V2 Minimum H1 + H2 Maximum  
Three Elbows  
Elbow only  
1 ft.  
305 mm  
610 mm  
610 mm  
1.2 m  
*
*
*
*
*
*
*
*
*
*
*
*
1 ft.  
2 ft.  
2 ft.  
4 ft.  
9 ft.  
18 ft.  
305 mm  
610 mm  
610 mm  
1.2 m  
6 in.  
1 ft.  
2 ft.  
3 ft.  
4 ft.  
152 mm  
305 mm  
610 mm  
914 mm  
1.2 m  
2 ft.  
2 ft.  
*
*
4 ft.  
*
9 ft.  
2.7 m  
*
2.7 m  
18 ft.  
5.5 m  
*
5.5 m  
H1 + H2 = 20 ft. (6.1 m) Maximum  
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum  
V2  
H1  
H2  
V1  
INSTALLED  
HORIZONTALLY  
Figure 7.12  
32  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Vent - Horizontal Termination  
No Elbow  
H1 = 16 in. (406 mm) Maximum  
H1  
Figure 7.13  
One 45º Elbow  
Do not use a 45º elbow in corner installations.  
Use two 90º elbows instead.  
H1  
Figure 7.14  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
Rear Vent - Horizontal Termination - (continued)  
H1 Maximum  
V1 Minimum  
H2  
305 mm  
H1 + H2 Maximum  
Two Elbows  
Back to Back  
90º Elbows  
1 ft.  
305 mm  
1 ft.  
2 ft.  
610 mm  
2 ft.  
3 ft.  
3 ft.  
3 ft.  
3 ft.  
610 mm 6 in.  
914 mm 1 ft.  
914 mm 2 ft.  
914 mm 3 ft.  
152 mm  
305 mm  
610 mm  
914 mm  
1.2 m  
2 ft.  
2 ft.  
610 mm  
610 mm  
1.2 m  
4 ft.  
5 ft.  
1.2 m  
1.5 m  
2.1 m  
3.7 m  
6.1 m*  
4 ft.  
7 ft.  
9 ft.  
2.7 m  
12 ft.  
20 ft.*  
914 mm  
4 ft  
17 ft.  
5.2 m  
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 = 3 ft. (914 mm) Maximum  
*H1 + H2 = 20 ft (6.1 m) Maximum  
V1  
H2  
H1  
Figure 7.15  
H1 Maximum  
V1 Minimum  
H2+ H3  
305 mm  
H1+ H2+ H3 Max.  
Three Elbows  
Back to Back  
90º Elbows  
1 ft. 305 mm  
1 ft.  
2 ft.  
610 mm  
2 ft. 610 mm 6 in.  
152 mm 1.5 ft. 457 mm 3.5 ft.  
1.1 m  
1.5 m  
2.1 m  
3.7 m  
4.6 m  
3 ft. 914 mm  
3 ft. 914 mm  
3 ft. 914 mm  
3 ft. 914 mm  
1 ft.  
2 ft.  
3 ft.  
4 ft.  
305 mm  
610 mm  
914 mm  
1.2 m  
2 ft.  
4 ft.  
610 mm  
1.2 m  
5 ft.  
7 ft.  
9 ft.  
2.7 m  
12 ft.  
15 ft.  
INSTALLED  
HORIZONTALLY  
12 ft.  
3.7 m  
V1+ H1+ H2+ H3= 40 ft. (12.2 m) Maximum H1= 3 ft. (914 mm) Maximum  
H1+ H2+ H3= 20 ft. (6.1 m) Maximum  
H3  
H2  
V1  
H1  
Figure 7.16  
34  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Vent - Vertical Termination  
One Elbow  
V1 Minimum  
6 in. 152 mm  
H1 Maximum  
2 ft. 610 mm  
3 ft. 914 mm  
1 ft.  
2 ft.  
3 ft.  
4 ft.  
5 ft.  
305 mm  
610 mm  
914 mm  
1.2 m  
5 ft.  
7 ft.  
8 ft.  
8 ft.  
1.5 m  
2.1 m  
2.4 m  
2.4 m  
1.5 m  
V1 + H1 = 40 ft. (12.2 m) Maximum  
H1 = 8 ft. (2.4 m) Maximum  
V1  
H1  
Figure 7.17  
V1 Minimum  
Back to Back 90º Elbows  
H1 + H2 Maximum  
Two Elbows  
3 ft.  
914 mm  
2 ft.  
4 ft.  
610 mm  
1.2 m  
6 ft.  
9 ft.  
1.8 m  
2.7 m  
3.7 m  
4.6 m  
6 ft.  
8 ft.  
1.8 m  
2.4 m  
12 ft.  
15 ft.  
V1 + H1 = 40 ft. (12.2 m) Maximum  
H1 + H2 = 8 ft. (2.4 m) Maximum  
V1  
INSTALLED  
HORIZONTALLY  
H1  
H2  
Figure 7.18  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
Rear Vent - Vertical Termination - (continued)  
H1 Maximum  
V1 Minimum  
H2  
H1 + H2 Maximum  
Three Elbows  
610  
mm  
2 ft.  
610 mm  
6 in.  
152 mm  
2 ft.  
4 ft.  
1.2 m  
3 ft.  
5 ft.  
7 ft.  
8 ft  
914 mm  
1.5 m  
1 ft.  
2 ft.  
3 ft.  
4 ft.  
305 mm  
610 mm  
914 mm  
1.2 m  
4 ft.  
6 ft.  
1.2 m  
1.8 m  
2.4 m  
3.1 m  
7 ft.  
11 ft.  
15 ft.  
18 ft.  
2.1 m  
3.4 m  
4.6 m  
5.5 m  
2.1 m  
8 ft.  
V2  
2.4 m  
10 ft.  
H1= 8 ft (2.4 m) Max.  
V1 + V2 + H1 + H2= 40 ft (12.2 m) Max.  
H1 + H2 = 20 ft (6.1 m) Max.  
H2  
V1  
Figure 7.19  
H1  
H1  
H2  
H3  
V1 Minimum  
H1 + H2 + H3 Maximum  
Three Elbows  
*
*
*
*
*
*
*
*
*
*
*
*
8 ft.  
9 ft.  
2.4 m  
2.7 m  
3.1 m  
3.1 m  
6 ft.  
7 ft.  
8 ft.  
8 ft.  
1.8 m  
2.1 m  
2.4 m  
2.4 m  
10 ft.  
10 ft.  
V1 + H1 + H2 + H3 = 40 ft. (12.2 m) Maximum  
*No specific restrictions on this value EXCEPT  
V1  
V1 + H1 + H2 + H3 cannot exceed 40 ft. (12.2 m) Maximum  
H1 + H2 + H3 = 8 ft. (2.4 m) Maximum  
H3  
H1  
H2  
INSTALLED  
Figure 7.20  
HORIZONTALLY  
36  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Coaxial to Colinear Venting  
OUTSIDE FACE OF  
FIREPLACE  
The coaxial to colinear adapter (DV-46DVA-GCL) is ap-  
proved for installations into solid fuel masonry or factory  
built fireplaces that have been installed in accordance  
with the National, Provincial, State and local building  
codes. The DV-46DVA-GCL must be recessed into exist-  
ing masonry fireplace. See Table 1 and Figure 7.21.  
EXHAUST VENT PIPE  
TOP OF FIREPLACE  
OPENING  
5 IN. MIN.  
INLET AIR VENT PIPE  
EXHAUST VENT PIPE  
3 IN. MIN.  
SHADED AREA DEFINED AS  
“INSIDE EXISTING MASONRY  
FIREPLACE”  
Figure 7.22. Existing Fireplace DV-46-CGL-CGL  
Clearance Requirements  
Figure 7.21. Coaxial/Colinear Appliance Connector  
Clearances to Combustibles:  
WARNING! Risk of Fire! Coaxial to colinear venting  
configuration may only be used in existing non-combus-  
tible chimney. Installation in any other venting application  
could cause fire.  
Refer to Section 5 for clearances to the appliance, man-  
tel, mantel legs and wall projection.  
Refer to Section 8 for pipe clearances to combustibles.  
Prior to installing the gas appliance:  
Termination Cap  
• Have the chimney and adjacent structure inspected  
and cleaned by qualified professionals. Hearth & Home  
Technologies recommends that NFI or CSIA certified  
professionals, or technicians under the direction of certi-  
fied professionals, conduct a minimum of a NFPA 211  
Level 2 inspection of the chimney.  
For installation of termination cap see minimum vent  
heights for various pitched roofs. See Section 6 of appli-  
ance owner’s manual.  
Flue Damper  
Fully lock the solid fuel fireplace’s flue damper in the open  
position, OR completely remove it.  
• Replace component parts of the chimney and fireplace  
as specified by the professionals.  
Venting Components  
The LINK-DV30B is approved for use with the coaxial/co-  
linear venting application. The LINK-DV30B kit includes:  
• Ensure all joints are properly engaged and the chimney  
is properly secured.  
• Two 30 feet sections of flexible vent pipe (3 inches Ø).  
One section is used to draw combustion air and the other  
section is used to expel exhaust gases.  
Table 1  
CLEARANCE TO COMBUSTIBLES REQUIREMENTS  
• One vertical termination cap.  
DV-46DVA-GCL  
3 IN.  
5 IN.  
Exhaust Vent Pipe  
CAUTION! DO NOT use any flue restrictor when vent-  
ing with the DV-46DVA-GCL adapter and LINK-DV30B  
kit. This may result in poor flame appearance, sooting,  
pilot malfunction, or overheating.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
Connecting the DV-46DVA-GCL Adapter to Appliance  
Top Vent  
three screws.  
• Attach one section of flexible vent pipe to the stainless  
steel flex pipe with three self-tapping screws.  
• Remove top seal cap and insulation if equipped. See  
Section 14, “Appliance Setup.” Attach the DVP-2SL to  
the 8 inch starting collar. Follow installation instructions  
included with DVP-2SL kit. Attach the DV-46DVA-GCL  
adapter to the appliance starting collar with 3-1/2 in.  
self-tapping screws. See Figure 7.23.  
• Attach one section of flexible vent pipe to the inlet collar  
on top of the DV-46DVA-GCL adapter with three self-  
tapping screws.  
• To minimize cold air drafts, seal around the flex vents  
at the damper inside the chimney with non-combustible  
unfaced fiberglass or rock wool insulation.  
Rear Vent  
• Remove the rear seal cap and insulation if equipped.  
Connect the DVP-2SLadapter to the vertically positioned  
elbow. Follow installation instructions included with DVP-  
2SLkit. Secure DV-46DVA-GCLadapter to DVP-2SLwith  
3-1/2 in. self-tapping screws. See Figure 7.23.  
The DV-46DVA-GCLadapter must be recessed into existing  
masonry fireplace. This measurement is taken from the top  
of the fireplace opening. See Table 1 and Figure 7.22.  
WARNING! Risk of Fire, Explosion or Asphyxiation!  
Do NOT connect this gas appliance to a chimney flue  
serving a separate solid fuel or gas burning appliance.  
Connecting the LINK-DV30B to the DV-46DVA-GCL  
adapter  
• May impair safe operation of this appliance or other  
appliances connected to the flue.  
• Insert the two sections of flexible vent pipe down the  
existing chimney.  
• Vent this appliance directly outside.  
• Attach one section of stainless steel flex pipe to the  
exhaust collar on top of the DV-46DVA-GCLadapter with  
• Use separate vent system for this appliance.  
REAR VENT  
TOP VENT  
TERMINATION CAP  
TERMINATION CAP  
CAUTION! DO NOT use any flue restric-  
tor when venting with the DV-46DVA-GCL  
adapter and LINK-DV30B kit. This may re-  
sult in poor flame appearance, sooting, pilot  
malfunction, or overheating.  
NOTICE: To achieve optimum perfor-  
mance of appliance, minimize or avoid  
V
V
bends in exhaust vent pipe.  
EXISTING CHIMNEY  
EXISTING CHIMNEY  
EXHAUST AIR  
VENT PIPE  
EXHAUST AIR  
VENT PIPE  
INLET AIR  
VENT PIPE  
INLET AIR VENT PIPE  
The first 3 feet of  
exhaust flue must be  
stainless flex pipe.  
The first 3 feet of  
exhaust flue must  
be stainless flex  
pipe.  
EXISTING CHIMNEY  
EXISTING CHIMNEY  
COAXIAL/COLINEAR  
APPLIANCE CONNECTOR  
To minimize cold air  
drafts, seal with  
non-combustible  
insulation.  
COAXIAL/COLINEAR  
APPLIANCE CONNECTOR  
To minimize cold air  
drafts, seal with  
non-combustible  
insulation.  
DVP-2SL  
DIRECT VENT FIREPLACE  
DVP-2SL  
DIRECT VENT FIREPLACE  
HEARTH  
FLOOR  
HEARTH  
FLOOR  
H
V
H
V
Minimum  
Maximum  
10 ft.  
40 ft.  
3.05 m  
12.2 m  
0 ft.  
2 ft.  
0 mm  
610 mm  
Minimum  
Maximum  
10 ft.  
40 ft.  
3.05 m  
12.2 m  
Figure 7.23  
38  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Vent Clearances and Framing  
8
A. Pipe Clearances to Combustibles  
B. Wall Penetration Framing  
WARNING! Risk of Fire! Maintain air space clearance to  
vent. DO NOT pack insulation or other combustibles:  
Combustible Wall Penetration  
Whenever a combustible wall is penetrated, you must  
frame a hole for the wall shield firestop(s). The wall shield  
firestop maintains minimum clearances and prevents cold  
air infiltration.  
• Between ceiling firestops  
• Between wall shield firestops  
• Around vent system  
• The opening must be framed on all four sides using the  
same size framing materials as those used in the wall  
construction.  
Failure to keep insulation or other material away from  
vent pipe may cause over heating and fire.  
• SLP pipe - A wall shield firestop must be placed on each  
side of an interior wall. A minimum 1-1/2 in. (38 mm)  
overlap of attached heat shields must be maintained.  
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).  
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184  
mm) thick.  
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If  
• DVP pipe - A wall shield firestop is required on one side  
only on interior walls. If your local inspector requires a  
wall shield firestop on both sides, then both wall shield  
firestops must have a heat shield (refer to Section 16.B.)  
attached to them.  
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.  
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to  
194 mm thick).  
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.  
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.  
(DVP-SLP Pipe Shown)  
• See Section 10.M. for information for regarding the in-  
stallation of a horizontal termination cap.  
Heat  
Shield  
3 in. (76 mm)  
top clearance *  
Heat  
Non-Combustible Wall Penetration  
3 in. (76 mm)  
top clearance  
If the hole being penetrated is surrounded by noncom-  
bustible materials such as concrete, a hole with diameter  
one inch greater than the pipe is acceptable.  
Shield  
1 in. (25 mm)  
clearance around  
vertical sections  
Whenever a non-combustible wall is penetrated, the wall  
shield firestop is only required on one side and no heat  
shield is necessary.  
1 in. (25 mm)  
clearance  
bottom & sides  
Wall  
Shield  
Firestop  
WALL  
3 in. (76 mm)  
top clearance *  
Heat  
Shield  
Heat  
Shield  
1 in. (25 mm)  
clearance  
bottom & sides  
10 in.  
12 in.  
12 in.  
Wall  
Shield  
Firestop  
C
D
10 in.  
B*  
WALL  
* When using SLP or SL-D pipe, minimum clearances from the vent pipe to combus-  
tible materials at inside wall firestops are: Top: 2-1/2 in. (64 mm)  
Bottom: 1/2 in. (13 mm)  
A*  
Sides: 1 in. (25 mm)  
Figure 8.1 Horizontal Venting Clearances To Combustible  
Materials  
A*  
B*  
C
D
in.  
mm  
in.  
42-3/4  
1086  
27-7/8  
708  
41-3/4  
1060  
44-1/8  
1111  
26-7/8  
683  
6000  
8000  
44-3/4  
1137  
29-7/8  
759  
28-7/8  
733  
mm  
* Shows center of vent framing hole for top or rear venting. The center of the  
hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.  
Figure 8.2 Wall Penetration  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
C. Install the Ceiling Firestop  
A ceiling firestop MUST be used between  
floors and attics.  
• DVP pipe only - Frame an opening 10 in.  
by 10 in. (254 mm by 254 mm) whenever  
the vent penetrates a ceiling/floor (see  
Figure 8.3).  
ATTIC ABOVE  
• SLP pipe only - Frame opening 9 in. x 9  
in. (229 mm x 229 mm) whenever the vent  
penetrates a ceiling/floor (see Figure 8.3).  
• Frame the area with the same sized lumber  
as used in ceiling/floor joist.  
A
• The ceiling firestop may be installed above or  
below the ceiling joists when installed with a  
attic insulation shield. It must be under joists  
between floors that are not insulated. Refer  
to Figure 8.4.  
• Secure with three fasteners on each side.  
A
WARNING! Risk of Fire! DO NOT pack insu-  
lation around the vent. Insulation must be kept  
back from the pipe to prevent overheating.  
A
PIPE  
DVP  
SLP  
10 in. (254 mm)  
9 in. (229 mm)  
Figure 8.3 Installing Ceiling Firestop  
INSTALL ATTIC INSULATION SHIELDS  
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM  
3 FASTENERS  
PER SIDE  
CEILING FIRESTOP  
CEILING FIRESTOP  
INSTALLED BELOW CEILING  
INSTALLED ABOVE CEILING  
Figure 8.4 Installing the Attic Shield  
40  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Install Attic Insulation Shield  
BEND ALL TABS INWARD 90°  
TO MAINTAIN CLEARANCE  
AND PREVENT INSULATION  
FROM FALLING INSIDE  
WARNING! Fire Risk. DO NOT allow loose materials or  
insulation to touch vent. Hearth & Home Technologies  
Inc. requires the use of an attic shield.  
The National Fuel Gas Code ANSI Z223.1 and NFPA 54  
requires an attic shield constructed of 26 gauge minimum  
metal that extends at least 2 in. (51 mm) above insulation.  
BEND 3 TABS  
OUTWARD TO  
Attic shields must meet specified clearance and be se-  
cured in place.  
FASTEN TO CEILING  
FIRESTOP-BEND  
REMAINING TABS  
INWARD 90 DEGREES  
TO MAINTAIN  
Flat Ceiling Installation  
• Remove one shield from box.  
NOTICE: Cut previously installed batt insulation to make  
room for the attic insulation shield.  
CLEARANCE  
INSERT 3  
SCREWS  
• Wrap shield around pipe if pipe is already installed in  
area to be insulated.  
• Match the three holes in each side and fasten with three  
screws to form a tube.  
• Bend three tabs on the bottom of the shield outward to  
allow attachment to the ceiling firestop.  
Figure 8.5 Attic Insulation Shield  
• Bend the remaining bottom tabs inward 90º to maintain  
the air space between the pipe and the shield. Set the  
shield on the ceiling firestop and attach to the firestop.  
E. Installing the Optional Heat-Zone® Gas Kit  
• Bend all tabs inward 90º around the top of the shield.  
These tabs must be used to prevent blown insulation  
from getting between the shield and vent pipe, and to  
maintain air space clearance.  
• Remove the knockout from the fireplace and discard it  
(see Figure 8.6).  
• Center the duct collar around the exposed hole and  
attach it to the fireplace with 3 screws. Note: Do this  
BEFORE final positioning of fireplace.  
• Determine the location for the air register/fan housing  
assembly.  
Vaulted Ceiling Installation  
Reference the Heat-Zone® Gas kit instructions for the  
remaining installation steps.  
• Remove one shield from box.  
NOTICE: Cut previously installed batt insulation to make  
room for the attic insulation shield.  
• Cut the attic insulation shield (if application is for vaulted  
ceiling) to fit your ceiling pitch. Snip cut edge to recreate  
1 in. bend tabs all the way around the bottom.  
• Wrap shield around pipe if pipe is already installed in  
area to be insulated.  
• Match the three holes in each side and fasten with three  
screws to form a tube.  
HEAT-ZONE® GAS  
ATTACHES HERE  
• Bend three tabs on the bottom of the shield outward to  
allow attachment to the ceiling firestop.  
• Bend the remaining bottom tabs inward 90º to maintain  
the air space between the pipe and the shield. Set the  
shield on the ceiling firestop and attach to the firestop.  
• Bend all tabs inward 90º around the top of the shield.  
These tabs must be used to prevent blown insulation  
from getting between the shield and vent pipe, and to  
maintain air space clearance.  
Figure 8.6 Heat-Zone® Cover Plate  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
Appliance Preparation  
9
NOTICE: Once the seal cap has been removed it CANNOT  
A. Top Vent  
be reattached.  
CAUTION! Risk of Cuts, Abrasions or Flying Debris.  
Wear protective gloves and safety glasses during instal-  
lation. Sheet metal edges are sharp.  
NOTICE: Once appliance is set up for top or rear venting,  
it CANNOT be changed at a later time.  
Figure 9.4 Remove the insulation basket and white insu-  
Figure 9.1 Cut the seal cap strap across the rectangles  
lation from the center vent pipe.  
next to the disk. For rear vent, skip this step.  
Figure 9.2 Remove the white gasket material covering  
the seal cap.  
Figure 9.5 Remove the insulation from the outer vent  
pipe. For rear venting there is no insulation in the outer  
vent pipe.  
Figure 9.3 Remove the seal cap.  
42  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 9.6 To attach the first section of vent pipe, make  
sure to use the fiberglass gasket in the manual bag to seal  
between the first vent component and the outer fireplace  
wrap. Use 2 self tapping screws to secure the gasket to  
the outer wrap.  
Secure the first section of venting to the fireplace by screw-  
ing through the two straps left over from cutting the seal  
cap strap in step 2.  
Figure 9.9 Fold the center parts of the retaining band out  
and use to remove the seal cap.  
NOTICE: Once the seal cap has been removed it CANNOT  
be reattached.  
B. Rear Vent  
CAUTION! Risk of Cuts, Abrasions or Flying Debris.  
Wear protective gloves and safety glasses during instal-  
lation. Sheet metal edges are sharp.  
NOTICE: Once appliance is set up for top or rear venting,  
it CANNOT be changed at a later time.  
Figure 9.7 Fold the tabs toward the center of the seal  
cap (90º) and remove the insulation gasket.  
Figure 9.10 Discard the vent cap, remove and discard  
the insulation basket.  
Figure 9.8 Cut the metal retaining band and fold the  
sides out.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
• Keep nailing tabs flush with the framing.  
• Level the appliance from side to side and front to back.  
• “Square” the unit by securing diagonal dimensions to  
within 1/4 inch of each other. See Figure 9.13.  
• Shim the appliance as necessary. It is acceptable to use  
wood shims underneath the appliance.  
• Secure the appliance to the framing by using nails or  
screws through the nailing tabs.  
• Secure the appliance to the floor by inserting two screws  
through the pilot holes at the bottom of the appliance.  
Figure 9.11 Attach the first vent section (it will snap into  
place). Slide the insulation gasket onto the vent section,  
up against the appliance and over the tabs.  
B
A
C. Installing the Non-combustible Board  
The factory supplied non-combustible board spans the dis-  
tance from the top of the fireplace to the center of the framing  
header. This board must be used. See Figure 9.12.  
HEADER  
Note: Diagonal dimensions (A) and (B) must be within  
1/4 inch of each other.  
Figure 9.13 Positioning the Appliance Squarely  
Figure 9.12 Non-combustible Board  
D. Securing and Leveling the Appliance  
WARNING! Risk of Fire! Prevent contact with:  
• Sagging or loose insulation  
• Insulation backing or plastic  
• Framing and other combustible materials  
Block openings into the chase to prevent entry of blown-  
in insulation. Make sure insulation and other materials  
are secured.  
DO NOT notch the framing around the appliance  
standoffs.  
NAILING TABS  
(BOTH SIDES)  
Failure to maintain air space clearance may cause  
overheating and fire.  
The diagram shows how to properly position and secure  
the appliance (see Figure 9.15). Nailing tabs are provided  
to secure the appliance to the framing members.  
PILOT HOLES  
• Bend out nailing tabs on each side.  
• Place the appliance into position.  
Figure 9.14 Proper Positioning and Securing of an Appliance  
44  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing Vent Pipe (DVP and SLP Pipe)  
10  
A. Assemble Vent Sections (DVP Pipe Only)  
Attach Vent to the Firebox Assembly  
Note: The end of the pipe sections with the lanced tabs will face  
toward the appliance.  
Attach the first pipe section to the starting collar:  
• Lanced pipe end to the starting collar  
• Inner pipe over inner collar  
• Push the pipe section until all lanced tabs snap in place  
• Lightly tug on pipe to confirm it has locked.  
Commercial, Multi-family (Multi-level exceeding two sto-  
ries), or High-Rise Applications  
All outer pipe joints must be sealed with silicone with a  
minimum of 300ºF continuous exposure rating, including the  
slip section that connects directly to the horizontal termi-  
nation cap.  
Figure 10.1 High Temperature Silicone Sealant  
• Apply a bead of silicone sealant inside the female outer  
pipe joint prior to joining sections. See Figure 10.1  
A
Lances  
• Only outer pipes need to be sealed. All unit collar, pipe,  
slip section, elbow and cap outer flues shall be sealed  
in this manner, unless otherwise stated.  
WARNING! Risk of Fire or Explosion! DO NOT break  
silicone seals on slip sections. Use care when remov-  
ing termination cap from slip pipe. If slip section seals  
are broken during removal of the termination cap, vent  
may leak.  
B
Figure 10.3  
Figure 10.2  
Assemble Pipe Sections  
Note: Make sure that the seams are not aligned to prevent  
unintentional disconnection.  
Per Figure 10.2:  
• Start the inner pipe on the lanced end of section A into  
the flared end of section B.  
• Start the outer pipe of section A over the outer pipe of  
section B.  
• Once both vents sections are started, push firmly until  
all lanced tabs lock into place.  
• Lightly tug on the pipe to confirm the tabs have locked.  
It is acceptable to use screws no longer than 1/2 in. (13  
mm) to hold outer pipe sections together. If predrilling holes,  
DO NOT penetrate inner pipe.  
CORRECT  
For 90º and 45º elbows that are changing the vent direction  
from horizontal to vertical, one screw minimum should be  
put in the outer flue at the horizontal elbow joint to prevent  
the elbow from rotating. Use screws no longer than 1/2  
in. (13 mm). If predrilling screw holes, DO NOT penetrate  
inner pipe.  
INCORRECT  
Figure 10.4 Seams  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
B. Assemble Vent Sections (SLP Pipe Only)  
C. Assemble Slip Sections  
To attach the first vent component to the starting collars  
of the appliance:  
• Slide the inner flue of the slip section into the inner flue of  
the pipe section and the outer flue of the slip section over  
the outer flue of the pipe section. See Figure 10.6.  
• Attach a DVP-2SL or DVP-SLP24 adapter to the starting  
collar of the appliance.  
• Slide together to the desired length.  
• Lock the vent components into place by sliding the pipe  
section onto the collar.  
• Align the seam of the pipe and seam of collar to allow  
engagement. Rotate the vent component to lock into  
place. Use this procedure for all vent components. See  
Figure 10.5.  
• Slide the gasket over the first vent section and place it  
flush to the appliance. This will prevent cold air infiltration.  
Caulk withaminimumof300ºFcontinuousexposurerating  
may be used to hold the part in place.  
Pilot hole  
• Continue adding vent components, locking each  
succeeding component into place.  
Figure 10.6 Slip Section Pilot Holes  
• Ensure that each succeeding vent component is securely  
fitted and locked into the preceding component.  
• Maintain a 1-1/2 in. (38 mm) overlap between the slip  
section and the pipe section.  
• Secure the pipe and slip section with two screws no  
longer than 1/2 in. (13 mm), using the pilot holes in the  
slip section. See Figure 10.7.  
Commercial, Multi-family (Multi-level exceeding two sto-  
ries), or High-Rise Applications  
For Installation into a commercial, multi-family (multi-level  
exceeding two stories) or high-rise applications: All outer  
pipe joints must be sealed with silicone with a minimum of  
300ºF continuous exposure rating, including the slip section  
that connects directly to the horizontal termination cap.  
• Apply a bead of silicone sealant inside the female outer  
pipe joint prior to joining sections. See Figure 10.1.  
• Only outer pipes need to be sealed. All unit collar, pipe,  
slip section, elbow and cap outer flues shall be sealed  
in this manner, unless otherwise stated.  
WARNING! Risk of Fire or Explosion! DO NOT break  
silicone seals on slip sections. Use care when remov-  
ing termination cap from slip pipe. If slip section seals  
are broken during removal of the termination cap, vent  
may leak.  
Figure 10.7 Screws into Slip Section  
• Continue adding pipe as necessary following instructions  
in “Assembling Pipe Sections.”  
NOTICE: If slip section is too long, the inner and outer flues  
of the slip section can be cut to the desired length.  
NOTICE: When installing a vent system with an HRC  
termination cap, all pipe system joints shall be sealed  
using silicone sealant with a minimum of 300ºF continuous  
exposure rating.  
Note: Align seams to engage pipe,  
then rotate counterclockwise to lock  
• Apply a bead of silicone sealant inside the female outer  
pipe joint prior to joining sections.  
Figure 10.5 Adding Venting Components  
• Only outer pipes are sealed, sealing the inner flue is not  
required.  
• All unit collar, pipe, slip section, elbow and cap outer  
flues shall be sealed.  
46  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D. Secure the Vent Sections  
E. Disassemble Vent Sections  
• Vertical runs of DVP pipe must be supported every 8 ft.  
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported  
rise.  
• Rotate either section (see Figure 10.10) so the seams  
on both pipe sections are aligned as shown in Figure  
10.11.  
• Vertical runs of SLP pipe must be supported every 8 ft.  
(2.44 m).  
• Pull carefully to separate the pieces of pipe.  
• Horizontal sections must be supported every 5 feet  
(1.52 m).  
• Vent supports or plumbers strap (spaced 120º apart)  
may be used to support vent sections. See Figures 10.8  
and 10.9.  
• Wall shield firestops may be used to provide horizontal  
support vent sections.  
• SLP ceiling firestops have tabs that may be used to  
provide vertical support.  
WARNING! Risk of Fire, Explosion or Asphyxiation!  
Improper support may allow vent to sag and separate.  
Use vent run supports and connect vent sections per in-  
stallation instructions. DO NOT allow vent to sag below  
connection point to appliance.  
Figure 10.10 Rotate Seams for Disassembly  
120º  
Figure 10.11 Align and Disassemble Vent Sections  
Figure 10.8 Securing Vertical Pipe Sections  
120º  
Figure 10.9 Securing Horizontal Pipe Sections  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
F. Install Decorative Ceiling Components  
(SLP only)  
LEVEL  
A decorative ceiling thimble can be installed on a flat ceil-  
ing through which the vent passes. The decorative ceiling  
thimble is used to cover the firestop.  
CATHEDRAL CEILING  
SUPPORT BOX  
• Seal the gap between the vent pipe and firestop using  
silicone with a minimum of 300ºF continuous exposure  
rating to prevent cold air infiltration.  
2 in. (51 mm) MIN. BELOW  
FINISHED CEILING  
• Install the decorative ceiling thimble by sliding it up to  
the ceiling and attaching it using the provided screws.  
Adecorative cathedral ceiling support box can be installed  
on a cathedral ceiling through which the vent passes.  
CUT HOLE 1/8 in. (3 mm)  
GREATER IN SIZE THAN  
PATTERN OF SUPPORT  
BOX AS IT IS PROJECTED  
ONTO ROOF LINE  
• Use a plumb-bob to mark the center line of the venting  
system on the ceiling and drill a small hole through the  
ceiling and roof at this point. Locate the hole and mark  
the outline of the cathedral ceiling support box on the  
outside roof.  
Figure 10.12  
• Remove shingles or other roof covering as necessary  
to cut the rectangular hole for the support box. Cut the  
hole 1/8 in. (3 mm) larger than the support box outline.  
• Lower the support box through the hole in the roof until its  
bottom is at least 2 in. (51 mm) below the ceiling (Figure  
10.12).  
• Level the support box both vertically and horizontally and  
temporarily tack it in place through the inside walls into  
the roof sheathing.  
• Use tin snips to cut the support box from the top corners  
down to the roof line and fold the resulting flaps to the  
roof. See Figure 10.13.  
• Nail the flaps to the roof AFTER running a bead of non  
hardening sealant between the flaps and the roof.  
Figure 10.13  
WARNING! Risk of Fire! Clean out ALL materials from  
inside the support box and complete the vertical vent run  
and termination.  
48  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
G. Install Metal Roof Flashing  
• See minimum vent heights for various pitched roofs  
(Figure 10.14) to determine the length of pipe to extend  
through the roof.  
CAULK  
• Slide the roof flashing over the pipe sections extending  
through the roof as shown in Figure 10.15.  
HORIZONTAL  
OVERHANG  
2 FT.  
20 INCHES MIN.  
VERTICAL  
MIN.  
WALL  
LOWEST  
DISCHARGE  
OPENING  
Figure 10.15  
GAS DIRECT VENT  
TERMINATION CAP  
H. Assemble and Install Storm Collar  
CAUTION! Risk of Cuts, Abrasions or Flying Debris.  
Wear protective gloves and safety glasses during instal-  
lation. Sheet metal edges are sharp.  
X
12  
ROOF PITCH  
IS X/ 12  
• Connect both halves of the storm collar with two screws  
(see Figure 10.16).  
H (MIN.) - MINIMUM HEIGHT FROM ROOF  
TO LOWEST DISCHARGE OPENING  
• Wrap the storm collar around the exposed pipe section  
closest to the roof and align brackets. Insert a bolt  
(provided) through the brackets and tighten the nut to  
complete the storm collar assembly. Make sure the collar  
is tight against the pipe section.  
Roof Pitch  
H (Min.) Ft.  
Flat to 6/12........................................1.0*  
Over 6/12 to 7/12............................1.25*  
Over 7/12 to 8/12..............................1.5*  
Over 8/12 to 9/12..............................2.0*  
Over 9/12 to 10/12............................. 2.5  
Over 10/12 to 11/12......................... 3.25  
Over 11/12 to 12/12........................... 4.0  
Over 12/12 to 14/12........................... 5.0  
Over 14/12 to 16/12........................... 6.0  
Over 16/12 to 18/12........................... 7.0  
Over 18/12 to 20/12........................... 7.5  
Over 20/12 to 21/12........................... 8.0  
• Slide the assembled storm collar down the pipe section  
until it rests on the roof flashing (see Figure 10.17).  
• Caulk around the top of the storm collar (see Figure 10.18).  
* 3 foot minimum in snow regions  
Figure 10.14 Minimum Height From Roof To Lowest Discharge  
Opening  
Figure 10.16 Assembling the Storm Collar  
NOTICE: Failure to properly caulk the roof flashing and  
pipe seams may permit entry of water.  
• Caulk the gap between the roof flashing and the outside  
diameter of the pipe.  
• Caulk the perimeter of the flashing where it contacts the  
roof surface. See Figure 10.15.  
• Caulk the overlap seam of any exposed pipe sections  
that are located above the roof line.  
Figure 10.17 Assembling the Storm Collar Around the Pipe  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
I. Install Vertical Termination Cap  
K. Heat Shield Requirements for Horizontal  
Termination  
• Attach the vertical termination cap by sliding the inner  
collar of the cap into the inner flue of the pipe section  
while placing the outer collar of the cap over the outer  
flue of the pipe section.  
WARNING! Risk of Fire! To prevent overheating and fire,  
heat shields must extend through the entire wall thick-  
ness.  
• Secure the cap by driving three self-tapping screws  
(supplied) through the pilot holes in the outer collar of  
the cap into the outer flue of the pipe (see Figure 10.18).  
• DO NOT remove the heat shields attached to the  
wall shield firestop and the horizontal termination cap  
(shown in Figure 10.20).  
• Heat shields must overlap 1-1/2 in. (38 mm) mini-  
mum.  
TERMINATION CAP  
There are two sections of the heat shield. One section  
is factory-attached to the wall shield firestop. The other  
section is factory-attached to the cap. See Figure 10.20.  
If the wall thickness does not allow the required 1-1/2 in.  
(38 mm) heat shield overlap when installed, an extended  
heat shield must be used.  
• If the wall thickness is less than 4 in./102 mm (DVP)  
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap  
and wall shield firestop must be trimmed. A minimum  
1-1/2 in. (38 mm) overlap MUST be maintained.  
(1 of 3)  
• Useanextendedheatshieldifthefinishedwallthickness  
is greater than 7-1/4 in. (184 mm).  
STORM  
COLLAR  
• The extended heat shield may need to be cut to length  
maintaining sufficient length for a 1-1/2 in. (38 mm)  
overlap between heat shields.  
SCREWS  
CAULK  
• Attach the extended heat shield to either of the existing  
heatshieldsusingthescrewssuppliedwiththeextended  
heat shield. Refer to vent components diagrams in the  
back of this manual.  
Figure 10.18  
• Rest the small leg on the extended heat shield on top  
of the pipe section to properly space it from the pipe  
section.  
J. Install Decorative Wall Components (SLP  
only)  
A decorative wall thimble can be installed on wall through  
which the vent passes. The decorative wall thimble is used  
to cover the wall shield firestop.  
Important Notice: Heat shields may not be field constructed.  
• Slide the decorative wall thimble over the last section of  
horizontal pipe before connecting the termination cap to  
the pipe.  
• Once the pipe section and the termination cap have  
been connected, slide the wall thimble up to the interior  
wall surface and attach with screws provided. See Figure  
10.19.  
Figure 10.19 Wall Thimble  
50  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: When using termination caps with factory-supplied  
heat shield attached, no additional wall shield firestop is  
required on the exterior side of a combustible wall.  
L. Install Horizontal Termination Cap (DVP  
and SLP Pipe)  
WARNING! Risk of Fire! The telescoping flue section of  
the termination cap MUST be used when connecting vent.  
• 1-1/2 (38 mm) minimum overlap of flue telescoping  
section is required.  
HEAT SHIELD OR  
HEAT SHIELD  
EXTENDED  
1-1/2 IN. (38 MM) MIN.  
HEAT SHIELD  
OVERLAP  
WALL SHIELD  
FIRESTOP  
Failure to maintain overlap may cause overheating and  
fire.  
• Vent termination must not be recessed in the wall. Siding  
may be brought to the edge of the cap base.  
SLIP SECTION  
CAN BE EXTENDED  
• Flash and seal as appropriate for siding material at  
outside edges of cap.  
INNER VENT  
SHEATHING  
• When installing a horizontal termination cap, follow  
the cap location guidelines as prescribed by current  
ANSI Z223.1 and CAN/CGA-B149 installation codes  
and refer to Section 6 of this manual.  
OUTER VENT  
INTERIOR  
EXTERIOR  
VENT DEPTH FROM BACK OF APPLIANCE TO  
OUTSIDE SURFACE OF EXTERIOR WALL  
(SEE CHART BELOW)  
CAUTION! Risk of Burns! Local codes may require in-  
stallation of a cap shield to prevent anything or anyone  
from touching the hot cap.  
Figure 10.20 Venting through the wall  
Cap Specification Chart  
NOTICE: For certain exposures which require superior  
resistance to wind-driven rain penetration, a flashing kit and  
HRC caps are available. When penetrating a brick wall, a  
brick extension kit is available for framing the brick.  
(depth without using additional pipe sections)  
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2  
Top Vent  
Depth  
Rear Vent  
Depth  
Top Vent  
Depth  
Rear Vent  
Depth  
2-3/4 in. to  
4-5/8 in.  
3-1/8 in. to  
5 in.  
5-1/8 in. to  
9-1/8 in.  
5-1/2 in. to  
9-1/2 in.  
6000  
Series  
8000  
DVP-HPC1 DVP-HPC1  
Top Vent  
Depth  
DVP-HPC2 DVP-HPC2  
Top Vent  
Depth  
Series  
Rear Vent  
Depth  
Rear Vent  
Depth  
2-3/4 in. to  
4-7/8 in.  
3-1/8 in. to  
5-1/4 in.  
4-7/8 in. to  
9 in.  
5-1/4 in. to  
9-3/8 in.  
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)  
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)  
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)  
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
Gas Information  
11  
A. Fuel Conversion  
C. Gas Connection  
• Make sure the appliance is compatible with available gas  
types.  
• Refer to Reference Section 16 for location of gas line  
access in appliance.  
• Conversions must be made by a qualified service  
technician using Hearth & Home Technologies specified  
and approved parts.  
• Gas line may be run through knockout(s) provided.  
• The gap between supply piping and gas access hole may  
be caulked with caulk withaminimumof300ºFcontinuous  
exposurerating or stuffed with non-combustible, unfaced  
insulation to prevent cold air infiltration.  
B. Gas Pressure  
• Optimum appliance performance requires proper input  
pressures.  
• Ensure that gas line does not come in contact with outer  
wrap of the appliance. Follow local codes.  
• Gas line sizing requirements will be determined in ANSI  
Z223.1 National Fuel Gas Code in the USA and CAN/  
CGA B149 in Canada.  
• Pipe incoming gas line into valve compartment.  
• Connect incoming gas line to the 1/2 in. (13 mm)  
connection on manual shutoff valve.  
• Pressure requirements are:  
WARNING! Risk of Fire or Explosion! Support control  
when attaching pipe to prevent bending gas line.  
Gas Pressure  
Minimum inlet pressure  
Maximum inlet pressure  
Manifold pressure  
Natural Gas  
5.0 in. w.c.  
10.0 in. w.c.  
3.5 in. w.c.  
Propane  
11.0 in. w.c.  
13.0 in. w.c.  
10.0 in. w.c.  
• A small amount of air will be in the gas supply lines.  
WARNING! Risk of Fire or Explosion! Gas build-up dur-  
ing line purge could ignite.  
• Purge should be performed by qualified service  
technician.  
• Ensure adequate ventilation.  
• Ensure there are no ignition sources such as sparks  
or open flames.  
WARNING! Risk of Fire or Explosion! High pressure  
will damage valve. Low pressure may cause explosion.  
• Verify inlet pressures. Verify minimum pressures when  
other household gas appliances are operating.  
Light the appliance. It will take a short time for air to purge  
from lines. When purging is complete the appliance will  
light and operate normally.  
• Install regulator upstream of valve if line pressure is  
greater than 1/2 psig.  
WARNING! Risk of Fire, Explosion or Asphyxiation!  
Check all fittings and connections with a non-corrosive  
commercially available leak-check solution. DO NOT use  
open flame. Fittings and connections could have loos-  
ened during shipping and handling.  
WARNING  
Fire Risk.  
Explosion Hazard.  
High pressure will damage valve.  
• Disconnect gas supply piping BEFORE  
pressure testing gas line at test pressures  
above 1/2 psig.  
WARNING! Risk of Fire! DO NOT change valve settings.  
This valve has been preset at the factory.  
• Close the manual shutoff valve BEFORE  
pressure testing gas line at test pressures  
equal to or less than 1/2 psig.  
D. High Altitude Installations  
NOTICE: If the heating value of the gas has been reduced,  
these rules do not apply. Check with your local gas utility  
or authorities having jurisdiction.  
Note: Have the gas supply line installed in accordance with  
local codes, if any. If not, follow ANSI 223.1. Installation  
should be done by a qualified installer approved and/or  
licensed as required by the locality. (In the Commonwealth  
of Massachusetts installation must be performed by a  
licensed plumber or gas fitter).  
When installing above 2000 feet elevation:  
• In the USA: Reduce burner orifice 4% for each 1000 feet  
above 2000 feet.  
• In CANADA: Reduce burner orifice 10% for elevations  
between 2000 feet and 4500 feet. Above 4500 feet,  
consult local gas utility.  
Note: A listed (and Commonwealth of Massachusetts ap-  
proved) 1/2 in. (13 mm) T-handle manual shut-off valve  
and flexible gas connector are connected to the 1/2 in. (13  
mm) control valve inlet.  
• If substituting for these components, please consult  
local codes for compliance.  
52  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Information  
12  
B. IntelliFire Plus™ Ignition System Wiring  
A. Wiring Requirements  
• Wire the appliance junction box to 110 VAC for proper  
operation of the appliance.  
NOTICE: This appliance must be electrically wired  
and grounded in accordance with local codes or, in the  
absence of local codes, with National Electric Code  
ANSI/NFPA 70-latest edition or the Canadian Electric  
Code CSA C22.1.  
WARNING! Risk of Shock or Explosion! DO NOT wire  
IPI controlled appliance junction box to a switched circuit.  
Incorrect wiring will override IPI safety lockout.  
• Wire the appliance junction box to 110-120 VAC. This is  
required for use of optional accessories (standing pilot  
ignition) or proper operation of the appliance (IntelliFire  
Plus™ ignition).  
• Refer to Figure 12.2, IPI Wiring Diagram.  
• This appliance is equipped with an IntelliFire Plus™  
control valve which operates on a 6 volt/1.5 AMP  
system.  
• A110-120 VAC circuit for this product must be protected  
with ground-fault circuit-interrupter protection, in  
compliance with the applicable electrical codes, when  
it is installed in locations such as in bathrooms or near  
sinks.  
• Plug the 6 volt transformer plug into the appliance junction  
box to supply power to the unit OR install 4 AA cell  
batteries (not included) into the battery pack before use.  
C. Standing Pilot Ignition System Wiring  
• Low voltage and 110 VAC voltage cannot be shared  
within the same wall box.  
• The standing pilot ignition system wiring does not require  
a 110 VAC supply to operate. See Figure 12.3  
WARNING! Risk of Shock or Explosion! DO NOT wire  
110V to the valve or to the appliance wall switch. Incorrect  
wiring will damage controls.  
• A 110 VAC junction box MUST be installed for use with  
a fan or remote control. See Figure 12.4 for junction box  
wiring. Keep wire lengths short as possible.  
Determine if the appliance uses an IntelliFire Plus™ igni-  
tion system or standing pilot ignition system:  
NOTICE: DO NOT wire 110 VAC to the millivolt valve! This  
• Open the control access panel or remove the decorative  
front.  
will damage the valve.  
• If using a thermostat use one compatible with a millivolt  
gas valve system:  
• A red or black ignitor button (as shown in Figure 12.1)  
indicates this appliance is standing pilot ignition.  
- Install the thermostat in the location as indicated in the  
thermostat instructions to ensure proper operation of  
appliance.  
RED OR  
BLACK  
BUTTON  
- Use low resistance thermostat wire for wiring from  
ignition system to the wall switch and thermostat.  
- Keep wire lengths short as possible.  
D. Optional Accessories Requirements  
• This appliance may be used with a wall switch, wall  
mounted thermostat and/or a remote control.  
Wiring for optional Hearth & Home Technologies approved  
accessories should be done now to avoid reconstruction.  
Follow instructions that come with those accessories.  
Figure 12.1 Ignitor Button  
• Hearth & Home Technologies recommends that Intel-  
liFire PlusTM wireless controls be used for their features  
and functionality with the IntelliFire PlusTM ignition sys-  
tem.  
• A standard ON/OFF switch is compatible.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
53  
FLAME  
SENSE  
IGNITER  
TO JUNCTION  
BOX (110V)  
MODULE  
FLAME  
MODULATION  
RC100  
RC200  
(OPTIONAL WALL CONTROLS)  
ORANGE  
(PILOT)  
GREEN  
(MAIN)  
BATTERY PACK  
6V DC  
BLACK  
RED  
THERMOSTAT WIRE  
ASSEMBLY / WALL  
SWITCH WIRE  
BROWN  
GROUND  
Figure 12.2 IPI Wiring Diagram  
STANDING  
PILOT  
BRN  
RED  
ON/OFF PIGGYBACK WIRE  
VALVE  
WHT  
RED  
THERMOSTAT  
WIRE ASSEMBLY / WALL  
SWITCH WIRE  
Figure 12.3 Standing Pilot Ignition Wiring Diagram  
54  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E. Electrical Service and Repair  
WARNING! Risk of Shock! Label all wires prior to dis-  
connection when servicing controls. Wiring errors can  
cause improper and dangerous operation. Verify proper  
operation after servicing.  
Romex  
Connector  
14/2WG  
WARNING! Risk of Shock! Replace damaged wire with  
type 105º C rated wire. Wire must have high temperature  
insulation.  
Cover Plate  
outside firebox  
F. Junction Box Installation  
If the box is being wired from the INSIDE of the appliance:  
• Remove the screw attaching the junction box/receptacle to  
the outer shell, rotate the junction box inward to disengage  
it from the outer shell (see Figure 12.4).  
Copper  
ground attached  
to GRN screw with  
GRN wire  
GRN wire  
inside box  
• Pull the electrical wires from outside the appliance through  
the opening into the valve compartment and secure wires  
with a Romex connector. See Figure 12.4.  
NOTICE: DO NOT wire  
110 VAC to wall switch.  
• Make all necessary wire connections to the junction box/  
receptacle and reattach the junction box/receptacle to the  
outer shell.  
Figure 12.4 Junction Box Detail  
G. Wall Switch Installation for Fan (Optional)  
If the box is being wired to a wall mounted switch for use  
with a fan (See Figure 12.5):  
Switch  
Minimum 14-3 AWG  
with Ground  
• The power supply for the appliance must be brought into  
a switch box.  
Red  
Black  
White  
Green  
Black  
White  
Green  
Junction Box  
• The power can then be supplied from the switch box to the  
appliance using a minimum of 14-3 with ground wire.  
Power  
Supply  
Wires  
• At the switch box connect the black (hot) wire and red  
(switch leg) wire to the wall switch as shown.  
Switch Box  
• At the appliance connect the black (hot), white (neutral)  
and green (ground) wires to the junction box as shown.  
Knockout  
Red  
• Add a 1/4 in. insulated female connector to the red (switch  
leg) wire, route it through the knockout in the face of the  
junction box, and connect to the top fan switch connector  
(1/4 in. male) as shown.  
Figure 12.5 Junction Box Wired to Wall Switch or BC10  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
Finishing  
13  
A. Mantel and Wall Projections  
B. Facing Material  
WARNING! Risk of Fire! Comply with all minimum clear-  
ances as specified. Framing closer than the minimums list-  
ed must be constructed entirely of noncombustible materials  
(i.e., steel studs, concrete board, etc.)  
• Metal front faces may be covered with non-combustible  
materials only.  
• Facing and/or finishing materials must not interfere with  
air flow through louvers, operation of louvers or doors,  
or access for service.  
Combustible Mantels  
• Facing and/or finishing materials must never overhang  
into the glass opening.  
Note: All  
measurements  
in inches.  
TO CEILING  
• Observe all clearances when applying combustible  
materials.  
18  
12  
11  
• Seal joints between the finished wall and appliance top  
and sides using a 300ºF minimum sealant. Refer to  
Figure 13.3.  
10  
32  
9
8
25  
7
19  
WARNING! Risk of Fire! DO NOT apply combustible  
materials beyond the minimum clearances. Comply with  
all minimum clearances to combustibles as specified in  
this manual. Overlapping materials could ignite and will  
interfere with proper operation of doors and louvers.  
6
18  
5
17  
4
16  
3
15  
14  
13  
12  
2-1/2  
11  
10  
5
B
FACTORY-INSTALLED NON-COMBUSTIBLE BOARD  
DO NOT REMOVE  
MEASUREMENTS FROM  
TOP EDGE OF THE OPENING  
Note: Measurement is taken from top of the opening,  
NOT the top of the fireplace.  
Figure 13.1 Minimum Vertical and Maximum Horizontal  
Dimensions of Combustibles  
A
Combustible Mantel Legs or Wall Projections  
INTERIOR WALL  
TOP VIEW  
A
B
A
B
inches  
millimeters  
inches  
39-3/4  
1010  
41-3/4  
1060  
41  
FIREPLACE OPENING  
6000  
8000  
1041  
48  
MANTEL LEG OR WALL PROJECTIONS  
millimeters  
1219  
If A minimum is ____, then B maximum is_____.  
Figure 13.3 Noncombustible Facing Diagram  
Inches  
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16  
A
Millimeters  
62  
1
87  
2
113  
3
138  
4
164  
5
189  
∞
∞
Inches  
B
Millimeters  
25  
51  
76  
102  
127  
Figure 13.2 Combustible Mantel Leg or Wall Projections  
(Acceptable on both sides of opening)  
56  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Doors  
Finishing Material:  
1 Inch Thick or Less  
Only doors certified for use with this appliance model may  
be used. Contact your dealer for a list of doors that may  
be used. Once you have determined what kind of door  
and finishing material is going to be used on the fireplace,  
you may use the table below which shows the door mod-  
els and the finishing material thickness allowed.  
Remove Finishing Strips. See Figure 13.7.  
NOTICE: Remove finishing strips before firing appliance.  
FINISH MATERIAL  
THICKNESS  
SEE  
FIGURE  
DOOR  
FIT  
Folio  
Inside  
Overlap  
Inside  
Any  
13.6  
13.4  
13.5  
13.4  
13.5  
13.4  
13.5  
13.4  
13.5  
13.4  
13.5  
13.6  
1 inch or less  
Arcadia  
Halston  
Greater than 1 inch  
1 inch or less  
1 in. MAX.  
Overlap  
Inside  
DOOR  
FINISHING MATERIAL  
(TOP EDGE)  
Greater than 1 inch  
1 inch or less  
Overlap  
Inside  
Finishing materials 1 inch maximum thick.  
Stop finishing material flush with opening.  
Chateau  
Greater than 1 inch  
1 inch or less  
Overlap  
Inside  
MT Hammer  
Greater than 1 inch  
1 inch or less  
Overlap  
Inside  
FINISHING STRIP NOT USED  
(See Figure 13.7 for  
Galleria  
Greater than 1 inch  
Any  
removal instructions)  
CF  
Inside  
NON-COMBUSTIBLE  
FINISHING MATERIAL  
Note: Finishing strips may be used to aid in positioning of  
non-combustible facing materials for some of the facing and  
door combinations specified in the table above. They must  
be removed following finishing work. See figure 13.7.  
Figure 13.4 Finishing Material 1 Inch Thick or Less  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
57  
Finishing Material Thickness:  
1-4 inches maximum  
Finishing Material Thickness:  
0-4 inches maximum  
NOTICE: Remove finishing strips before firing appliance.  
NOTICE: Remove finishing strips before firing appliance.  
FINISHING  
STRIPS USED  
FINISHING STRIP NOT USED  
(See Figure 13.7 for  
removal instructions)  
NON-COMBUSTIBLE  
FINISHING MATERIAL  
NON-COMBUSTIBLE  
FINISHING MATERIAL  
FINISHING  
MATERIAL  
FINISHING  
MATERIAL  
DOOR  
A
(Outside door width)  
C
(Includes 1/8 in. opening each side of door)  
DOOR  
FINISHING MATERIAL  
FINISHING MATERIAL  
Figure 13.6 Folio/CF Inside Fit  
B
8000 Models  
6000 Models  
D
Inches  
44-1/16  
35-15/16  
44-5/16  
36-5/16  
Millimeters  
1119  
Inches  
37-1/16  
34-1/16  
37-5/16  
34-7/16  
Millimeters  
A
(Outside door width)  
A
B
C
D
941  
865  
948  
882  
913  
1126  
922  
C
(Includes 1/8 in. opening each side of door)  
Finishing material thickness, 1-4 inches maximum  
B = Top of door to bottom of fireplace.  
D = Bottom of Finishing Material to Bottom of Fireplace  
Figure 13.5 Finishing Material Thickness Greater Than One Inch  
58  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removal of Finishing Strips  
NOTICE: Remove finishing strips before firing appliance.  
Remove glass frame assembly to access finishing strip  
screws.  
FINISHING STRIPS REMOVED  
Figure 13.7 Removing Finishing Strips.  
31-7/8 IN. (6000)  
33-11/16 IN. (8000)  
3-3/4 IN.  
(6000, 8000)  
35-5/16 IN. (6000)  
43 IN. (8000)  
Figure 13.8. Clean Face Door Dimensions  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
59  
D. Elevated Hearth Systems  
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various  
dimensions. Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance  
will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 in. The 9-1/4 in. elevation will also  
have to be added to the following: Wall penetration referenced in Figure 8.2 (Wall penetration) and Rough Opening Height  
(header height) referenced in Figure 5.2. Note: Finished floor thickness should also be considered when determining in-  
stallation dimensions.  
ELEVATED APPLIANCE  
DIMENSION  
MARBLE LEG CUT  
LENGTH  
MODEL  
DESCRIPTION  
KENWOOD CABINET  
PART #  
See Note 1  
See Note 2  
KDC48DBP  
0
33 in.  
33 in.  
KENWOOD CABINET W/ BASE  
KENWOOD CORNER CABINET  
KDC48DBP W/ HTKDC48DBP  
KDA48DBP  
9-1/4 in.  
0
33 in.  
6000  
Series  
KENWOOD CORNER CABINET W/ BASE KDA48DBP W/ HTKDA48DBP  
9-1/4 in.  
0 (See Note 3)  
9-1/4 in.  
1-1/16 in.  
0 (See Note 3)  
9-1/4 in.  
33 in.  
KENWOOD MANTEL  
AFKDMPB  
33 in.  
KENWOOD MANTEL W/ BASE  
LUNA SURROUND  
AFKDMPB W/ HTKDMPB  
LUNA-36-GY  
33 in.  
N/A  
KENWOOD MANTEL  
AFKDMPC  
32-7/8 in.  
32-7/8 in.  
8000  
Series  
KENWOOD MANTEL W/ BASE  
AFKDMPC W/ HTKDMPC  
Note 1. Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2).  
Note 2. Verify Marble Cut Lengths on site prior to cutting.  
Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.  
60  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appliance Setup  
14  
A. Remove Fixed Glass Assembly  
F. Ember Placement  
See Section 14.H.  
WARNING! Risk of Explosion! Follow ember placement  
instructions in manual. DO NOT completely block burner  
ports with ember material. Replace ember material annu-  
ally. Improperly placed embers interfere with proper burner  
operation.  
B. Remove the Shipping Materials  
Remove shipping materials from inside or underneath the  
firebox.  
Ember material is shipped with this gas appliance. To place  
the ember material:  
C. Clean the Appliance  
Clean/vacuum any sawdust that may have accumulated  
inside the firebox or underneath in the control cavity.  
• Embers CANNOT completely block burner ports. Care  
should be taken not to block the lighting trail of ports.  
D. Accessories  
• Embers may only be placed in areas as shown in Figure  
14.2.  
Install approved accessories per instructions included  
with accessories. Contact your dealer for a list of ap-  
proved accessories.  
• LP Only: Using dime-size pieces of Glowing Embers®,  
overlaptheburnerports(seeFigure14.3).Theimpingement  
created by the embers will help blend the fire.  
WARNING! Risk of Fire and Electric Shock! Use ONLY  
Hearth & Home Technologies-approved optional acces-  
sories with this appliance. Using non-listed accessories  
could result in a safety hazard and will void the warranty.  
• Save the remaining ember materials for use during  
appliance servicing. The embers provided should be  
enough for 3 to 5 applications.  
E. Burner Top Installation  
1. Bend the two tabs upward as shown in Figure 14.1.  
EMBERS  
NO EMBERS IN SHADED AREAS  
2. To install the fiber burner, mate the locating holes with  
the guide sleeves. Install fiber burner top so that it  
makes full contact with the underlying burner assem-  
bly.  
3. Ensure that the ports in the steel burner are visible  
through the holes in the fiber burner top.  
LOCATING HOLES  
FIBER BURNER TOP  
Figure 14.2 Placement of Embers  
BEND TABS UP  
AIR SCOOP  
PILOT COVER  
BURNER ASSEMBLY  
BURNER SHIELD  
GUIDE SLEEVES  
Figure 14.3 Embers Overlapping Burner Port Holes (LP only).  
Figure 14.1  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61  
G. Install the Log Assembly  
Log Assembly: LOGS-6C  
Models: 6000C-IPILP, 6000CBV-IPI  
6000C, 6000C-IPI  
LOCATING HOLES  
FIBER BURNER TOP  
LOG PLACEMENT TABS  
TAB BENT IN = NG  
BURNER SHIELD  
PILOT COVER  
BURNER ASSEMBLY  
LOG PLACEMENT INDENTATIONS  
TAB NOT BENT = LP  
GUIDE SLEEVES  
GRATE TINE  
Figure 1  
Figure 2. Log Placement Tabs  
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2164-701): Locate log placement tabs on the pilot cover. Bend  
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots  
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits  
squarely and completely on pilot cover with tabs engaged (see Figure 4).  
LOG PLACEMENT TABS  
1
LOG PLACEMENT SLOTS  
Figure 3  
Figure 4  
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the  
bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly  
on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.  
Bottom view of  
Logs # 2 and 3  
LEFT GRATE TINE  
SLOTS  
1
2
2
3
GROOVES  
Figure 5  
Figure 6  
Log #2 (SRV2164-702): Mate the slot located on the bottom of Log #2 with the left tab on top of Log #1. After slot and tab  
have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log # 2  
toward the left until it rests against the far left grate tine.  
62  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOSE  
RIGHT GRATE TINE  
1
1
3
2
2
3
4
Figure 7  
Figure 8  
Log #3 (SRV2164-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.  
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar  
and slide Log # 3 toward the right until it rests against the far right grate tine (see Figure 7).  
Log #4 (SRV2164-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right  
to left under Log #2 to fit completely and securely into the indentation (see Figure 8). Nose of log #4 should be pulled to fit  
securely against right hand side of log indentation.  
LOG #6 CONTACTS TOP OF LOG #4  
FLAT AREA  
1
1
2
3
2
3
5
4
6
5
4
LOG CONTACTS GRATE TINES  
Figure 9  
Figure 10  
Log #5 (SRV2164-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits  
completely and securely in the recessed indentation (see Figure 9). Log #5 should be pulled to the left hand side of log  
indentation.  
Log #6 (SRV2164-706): Mate the groove located on the lower end of Log #6 with the fourth grate tine (from left to right) as  
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will also  
rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing move-  
ment or shifting.  
2164-935C  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
63  
G. Install the Log Assembly (continued)  
Log Assembly: LOGS-8C  
Models: 8000C, 8000C-LP, 8000C-IPI,  
8000C-IPILP, 8000CBV-IPI  
LOCATING HOLES  
FIBER BURNER TOP  
LOG PLACEMENT INDENTATIONS  
LOG PLACEMENT TABS  
TAB BENT IN = NG  
BURNER SHIELD  
PILOT COVER  
BURNER ASSEMBLY  
TAB NOT BENT = LP  
GUIDE SLEEVES  
GRATE TINE  
Figure 2. Log Placement Tabs  
Figure 1  
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2168-701): Locate log placement tabs on the pilot cover. Bend  
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots  
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits  
squarely and completely on pilot cover with tabs engaged. See Figure 4.  
LOG PLACEMENT TABS  
1
LOG PLACEMENT SLOTS  
Figure 4  
Figure 3  
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the  
bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly  
on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.  
Bottom view of  
Logs # 2 and 3  
LEFT GRATE TINE  
SLOTS  
1
2
2
3
GROOVES  
Figure 6  
Figure 5  
Log #2 (SRV2168-702): Mate the slot located on the bottom of Log #2 with the left log placement tab on top of Log #1.  
After slot and tab have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar  
and slide Log # 2 toward the left until it rests against the far left grate tine.  
64  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RIGHT GRATE TINE  
1
1
3
2
2
3
4
HORIZONTAL GRATE BAR  
LOG #4 CONTACTS LOG #2  
Figure 7  
Figure 8  
Log #3 (SRV2168-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.  
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar  
and far right grate tine. Log # 3 will sit down on top of both the grate tine and the horizontal grate bar (see Figure 7).  
Log #4 (SRV2168-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right to  
left under Log #2 to fit completely and securely into the indentation (see Figure 8). The back or Log # 4 should rest against  
the far left grate tine as well as contact Log # 2.  
LOG #6 CONTACTS TOP OF LOG #4  
FLAT AREA  
1
1
2
3
2
3
6
4
5
5
4
Figure 10  
Figure 9  
LOG CONTACTS GRATE TINES  
Log #5 (SRV2168-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits  
completely and securely in the indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.  
Log #6 (SRV2168-706): Mate the groove located on the lower end of Log #6 with the fourth tine (from left to right) as  
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will  
also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing  
movement or shifting.  
2168-935C  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
65  
H. Fixed Glass Assembly  
J. Air Shutter Setting  
WARNING! Risk of Asphyxiation! Handle fixed glass  
assembly with care. Inspect the gasket to ensure it is  
undamaged and inspect the glass for cracks, chips or  
scratches.  
Air shutter settings should be adjusted by a qualified ser-  
vice technician at the time of installation. The air shutter is  
set at the factory for minimum vertical vent run. Adjust air  
shutter for longer vertical runs. See Figure 14.5.  
• DO NOT strike, slam or scratch glass.  
• Loosen the wing nut.  
• DO NOT operate fireplace with glass removed, cracked,  
broken or scratched.  
• Move the air handle to the left to open the air shutter.  
• Move the air handle to the right to close the air shutter.  
• Tighten the wing nut.  
• Replace as a complete assembly.  
Removing Fixed Glass Assembly  
NOTICE: If sooting occurs, provide more air by opening  
the air shutter.  
• Pull the four glass assembly latches out of the groove on  
the glass frame. Remove glass door from the appliance  
(see Figure 14.4).  
Replacing Fixed Glass Assembly  
• Replace the glass door on the appliance. Pull out and  
latch the four glass assembly latches into the groove on  
the glass frame.  
AIR SHUTTER  
WING NUT  
LATCHES  
(BOTH BOTTOM  
AND TOP)  
Figure 14.5 Air Shutter  
GLASS  
ASSEMBLY  
Air Shutter Settings  
NG  
LP  
6000  
8000  
1/4 in.  
1/4 in.  
3/4 in.  
3/4 in.  
Figure 14.4 Fixed Glass Assembly  
I. Install Trim and/or Surround  
• Install optional trim kits and/or surrounds using the  
instructions included with the accessory.  
• Use non-combustible materials to cover the gap between  
the sheet rock and the appliance (when applicable to the  
model).  
66  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
15  
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do  
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and  
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact  
your dealer to arrange a service call by a qualified service technician.  
A. Standing Pilot Ignition System  
Symptom  
Possible Causes  
Corrective Action  
1. After repeated triggering A. No gas or low gas pressure.  
of the red or black piezo  
Check the remote shut-off valves from the appliance. Usually, there  
is a valve near the gas main. There can be more than one valve be-  
tween the appliance and the main.  
ignitor button, the spark  
ignitor will not light the  
B. No lp in tank.  
pilot.  
Check the LP (propane) tank. You may be out of fuel.  
C. Ignitor.  
Check the spark at the electrode and pilot. If no spark and electrode  
wire is properly connected, replace the ignitor. Verify that there is no  
short in electrode wire.  
D. Pilot or misaligned electrode  
(spark at electrode).  
Using match, light the pilot. If the pilot lights, turn off the pilot and  
trigger the piezo ignitor button again. If the pilot lights, an improper  
gas/air mixture caused the bad lighting and a longer purge period is  
recommended. If the pilot will not light, ensure the gap at the elec-  
trode and pilot is one-eighth in. to have a strong spark. If the gap is  
OK, replace the pilot.  
2. The pilot will not stay lit  
after carefully following  
the lighting instructions.  
A. Thermocouple.  
Check that the pilot flame impinges on the thermocouple. Adjust the  
pilot for proper flame impingement.  
Ensure that the thermocouple connection at the gas valve is fully in-  
serted and tight (hand tighten plus 1/4 turn).  
Verify proper voltage output from the thermocouple to the valve.  
Place one millivolt meter lead wire on the thermocouple copper lead.  
Place the second lead wire on the solder button on the back of the  
valve (blue wire). Start the pilot and hold the valve knob in. The mil-  
livolt reading should read 8-16 millivolts. If millivolt reading is less  
than 8 millivolts, replace thermocouple.  
B. Improper gas inlet pressure. Natural gas should be 5-10 in. w.c. LP should be 11-13 in. w.c. Verify  
pressure with manometer.  
C. Valve.  
If the thermocouple is producing 8-16 millivolts, replace control valve.  
3. The pilot is burning,  
there is no burner  
A. ON/OFF switch or wires.  
Check the ON/OFF switch and wires for proper connections. Place  
the jumper wires across the terminals at the ON/OFF switch. If the  
burner comes on, replace the ON/OFF switch. If the ON/OFF switch  
is OK, place the jumper wires across the ON/OFF switch wires at the  
gas valve. If the burner comes on, the wires are faulty or connections  
are bad.  
flame, the valve knob is  
in the ON position, and  
the ON/OFF switch is in  
the ON position.  
B. Thermopile may not be gen-  
erating sufficient millivoltage.  
Check that the pilot flame impinges thermopile properly.  
Be sure the wire connections from the thermopile at the gas valve  
terminals are tight and that the thermopile is fully inserted into the  
pilot bracket.  
Check the thermopile with a millivolt meter. Take the reading at TH-  
TP&TP terminals of the gas valve. The meter should read 350 mil-  
livolts minimum, while holding the valve knob depressed in the pilot  
position, with the pilot lit, and the ON/OFF switch in the OFF position.  
Replace the thermopile if the reading is below the specified mini-  
mum.  
With the pilot in the ON position, disconnect the thermopile leads  
from the valve. Take a reading at the thermopile leads. The reading  
should be 350 millivolts minimum. Replace the thermopile if the read-  
ing is below the minimum.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
67  
Troubleshooting (continued)  
Symptom  
Possible Cause  
Corrective Action  
3. (Continued)  
C. Valve.  
Turn the valve knob to the ON position. Place the ON/  
OFF switch in the ON position. Take a reading with a  
millivolt meter at the thermopile terminals. The millivolt  
meter should read greater than 125mV. If the reading  
is acceptable, and if the burner does not come on, re-  
place the gas valve.  
D. Plugged burner orifice.  
E. Wall switch or wires.  
Check the burner orifice for stoppage. Remove stop-  
page.  
Check the wall switch and wires for proper connec-  
tions. Place the jumper wires across the terminals at  
the wall switch. If the burner comes on, replace the  
wall switch. If the wall switch is OK, place the jumper  
wires across the wall switch wires at the gas valve. If  
the burner comes on, the wires are faulty or connec-  
tions are bad.  
4. Frequent pilot outage A. Pilot flame may be too high or too low, or blow- Clean thermocouple and adjust the pilot flame for  
problem.  
ing out (high pressure), causing pilot safety to  
drop out.  
proper flame impingement. Follow lighting instructions  
carefully.  
5. The pilot and main  
burner extinguish  
while in operation.  
A. No LP in tank.  
Check the LP (propane) tank. Refill the fuel tank.  
B. Improper gas inlet pressure.  
Natural gas should be 5-10 in. w.c. LP should be 11-13  
in. w.c. Verify pressure with manometer.  
C. Inner vent pipe leaking exhaust gases back  
into the system.  
Check venting system for damage. Replace/repair im-  
properly assembled pipe sections.  
D. Glass installed improperly.  
Check to ensure glass is installed properly. Replace  
fixed glass panel assembly.  
E. Thermopile or thermocouple.  
F. Improper vent cap installation.  
Replace pilot if necessary.  
Check for proper installation and freedom from debris  
or blockage.  
6. Glass soots.  
A. Flame impingement.  
Adjust the log set so that the flame does not exces-  
sively impinge on it. Refer to log instructions.  
B. Improper air shutter setting.  
Refer to manual for shutter set points. Ensure that set  
point is correct for appliance/gas type. If unit has ad-  
justable shutter, it may be necessary to increase shut-  
ter opening.  
C. Debris around air shutter.  
Inspect the opening at the base of the burner. NO MA-  
TERIAL SHOULD BE PLACED IN THIS OPENING.  
7. Flame burns blue  
and lifts off burner.  
A. Insufficient oxygen being supplied.  
Ensure that the vent cap is installed properly and free  
of debris. Ensure that the vent system joints are tight  
and have no leaks.  
Ensure that no debris has been placed at the base of,  
or in the area of the air holes in the center of the base  
pan beneath the burner.  
Ensure that the glass is tightened properly on the unit,  
particularly on top corners.  
68  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. IntelliFire Plus™ Ignition System  
Symptom  
Possible Cause  
Corrective Action  
1. Pilot won’t light.  
The ignitor/module  
makes noise, but no  
spark.  
A. Incorrect wiring.  
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are  
connected to correct terminals on module and pilot assembly.  
B. Loose connections or electrical  
shorts in the wiring.  
Verify no loose connections or electrical shorts in wiring from mod-  
ule to pilot assembly. Verify connections underneath pilot assembly  
are tight; also verify igniter and flame sense wires are not grounding  
out to metal chassis, pilot burner, pilot enclosure, mesh screen if  
present, or any other metal object.  
C. Ignitor gap is too large.  
Verify gap of igniter to right side of pilot hood. The gap should be  
approximately .17 in. or 1/8 in. (3 mm).  
2. Pilot won’t light,  
there is no noise or  
spark.  
A. No power, transformer installed  
incorrectly, or depleted batteries.  
Verify that transformer is installed and plugged into module. Check  
voltage of transformer at connection to module. Acceptable read-  
ings of a good transformer are between 6.4 and 6.6 volts AC. Bat-  
tery power supply voltage must be at least 4 volts. If below 4 volts,  
replace batteries.  
B. A shorted or loose connection in  
wiring configuration or wiring har-  
ness.  
Remove and reinstall the wiring harness that plugs into module.  
Verify there is a tight fit. Verify pilot assembly wiring to module. Re-  
move and verify continuity of each wire in wiring harness. Replace  
any damaged components.  
C. Improper wall switch wiring.  
D. Module not grounded.  
Verify that 110/VAC power is “ON” to junction box.  
Verify black ground wire from module wire harness is grounded to  
metal chassis of appliance.  
3. Pilot sparks, but  
Pilot will not light.  
A. Gas supply.  
Verify that incoming gas line ball valve is “open”. Verify that inlet  
pressure reading is within acceptable limits.  
B. Ignitor gap is too large.  
Verify gap of igniter to right side of pilot hood. The gap should be  
approximately .17 in. or 1/8 in. (3 mm).  
C. Module is not grounded.  
D. Pilot valve solenoid  
Verify module is securely grounded to metal chassis of appliance.  
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.  
If below 1.5 volts, replace module. If 1.5 volts or greater, replace  
valve.  
4. Pilot lights but con-  
tinues to spark, and  
main burner will not  
ignite. (If the pilot  
continues to spark  
after the pilot flame  
has been lit, flame  
rectification has not  
occurred.)  
A. A shorted or loose connection in  
flame sensing rod.  
Verify all connections to wiring diagram in manual. Verify connec-  
tions underneath pilot assembly are tight. Verify flame sense or ig-  
niter wires are not grounding out to metal chassis, pilot burner, pilot  
enclosure or screen if present, or any other metal object.  
B. Poor flame rectification or contami- With fixed glass assembly in place, verify that flame is engulfing  
nated flame sensing rod.  
flame sensing rod on left side of pilot hood. Flame sensing rod  
should glow shortly after ignition. With a multi-meter, verify that  
current in series between module and sense lead is at least 0.14  
microamps. Verify correct pilot orifice is installed and gas inlet is set  
to pressure specifications. Polish flame sensing rod with fine steel  
wool to remove any contaminants that may have accumulated on  
flame sensing rod.  
C. Module is not grounded.  
Verify module is securely grounded to metal chassis of appliance.  
Verify that wire harness is firmly connected to the module.  
D. Damaged pilot assembly or con-  
taminated flame sensing rod.  
Verify that ceramic insulator around the flame sensing rod is not  
cracked, damaged, or loose. Verify connection from flame sensing  
rod to white sensor wire. Polish flame sensing rod with fine steel  
wool to remove any contaminants that may have accumulated on  
flame sensing rod. Verify continuity with a multi-meter with ohms set  
at lowest range. Replace pilot if any damage is detected.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
69  
Reference Materials  
16  
A. Appliance Dimension Diagram  
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.  
L
M
J
K
N
TOP VIEW  
H
GAS LINE  
ACCESS  
R
I
D
C
G
O
E
Q
B
A
P
F
LEFT SIDE  
FRONT VIEW  
RIGHT SIDE  
Location  
Inches Millimeters  
Location  
Inches  
Millimeters  
J
K
L
21  
11-11/16  
28-1/2  
14-1/4  
8-1/2  
2-7/8  
8-1/2  
1
533  
297  
724  
362  
216  
73  
A
B
C
D
E
F
G
H
I
41  
1041  
918  
851  
879  
57  
36-1/8  
33-1/2  
34-5/8  
2-1/4  
M
N
O
P
Q
R
9-11/16  
26-7/8  
6 dia  
246  
683  
152  
1013  
216  
25  
40-7/8  
1038  
39-7/8  
Figure 16.1 Appliance Dimensions-6000 Models  
70  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
L
M
J
K
N
TOP VIEW  
H
GAS LINE  
ACCESS  
R
I
D
C
G
E
Q
O
B
A
P
F
LEFT SIDE  
RIGHT VIEW  
FRONT VIEW  
Location  
Inches Millimeters  
Location  
Inches  
48  
Millimeters  
1219  
1096  
902  
J
K
L
21  
11-11/16  
35-1/2  
17-3/4  
8-1/2  
2-7/8  
8-1/2  
1
533  
297  
902  
451  
216  
73  
A
B
C
D
E
F
G
H
I
43-1/8  
35-1/2  
36-5/8  
2-3/8  
9-15/16  
28-7/8  
6
M
N
O
P
Q
R
930  
60  
252  
216  
25  
734  
152  
42-7/8  
1089  
41-7/8  
1064  
Figure 16.2 Appliance Dimensions-8000 Models  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
71  
B. Vent Components Diagrams  
Effective Length  
Pipe  
10-1/2 in.  
(267 mm)  
Inches  
4
Millimeters  
102  
°
45  
DVP4  
Effective  
Height/Length  
DVP6  
6
12  
152  
305  
DVP12  
DVP24  
DVP36  
DVP48  
DVP6A  
4-7/8 in.  
(124 mm)  
24  
610  
36  
914  
10-7/8 in.  
(276 mm)  
48  
1219  
76 to 152  
DVP Pipe (see chart)  
3 to 6  
DVP45 (45º Elbow)  
DVP12A 3 to 12 76 to 305  
11-3/8 in.  
(289 mm)  
10 in.  
(254 mm)  
1 in.  
(25 mm)  
7-3/8 in.  
(187 mm)  
1-1/4 in. (32 mm)  
10 in.  
(254 mm)  
9-1/4 in.  
(235 mm)  
Assembled  
Height: 24 in./610 mm  
Diameter: 10 in./254 mm  
1/2 in. TYP  
(13 mm)  
13-1/4 in.  
(337 mm)  
DVP-FS (Ceiling Firestop)  
DVP-AS2  
DVP90ST (90° Elbow)  
12 in.  
(305 mm)  
1 in.  
(25 mm)  
8 in.  
(203 mm)  
1- 1/2 in.  
(38 mm)  
10 in.  
(254 mm)  
14 in.  
(356 mm)  
UP  
5 in.  
(127 mm)  
12 in.  
(305 mm)  
6 in.  
(152 mm)  
DVP-HVS (Vent Support)  
DVP-WS (Wall Shield Firestop)  
Figure 16.3 DVP vent components  
72  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Vent Components Diagrams (continued)  
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be  
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the  
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B  
will be required.  
8 in.  
(203 mm)  
Heat  
Shield  
15-1/8 in.  
(384 mm)  
Minimum  
Effective Length  
Maximum  
Effective Length  
Term Cap  
Trap1  
Max  
Effective  
Length  
12 in.  
(305 mm)  
3-1/8 in.  
79 mm  
4-5/8 in.  
117 mm  
9-3/8 in.  
238 mm  
DVP-TRAP  
Horizontal Termination Cap  
5-3/8 in.  
137 mm  
Trap2  
DVP-TRAP2  
DVP-TRAP1  
DVP-TRAPK2  
DVP-TRAPK1  
DVP-HPC2  
DVP-HPC1  
Figure 16.4 DVP vent components  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
73  
B. Vent Components Diagrams (continued)  
31 in.  
(787 mm)  
13-1/4 in.  
(337 mm)  
24-5/8 in.  
(625 mm)  
27-1/2 in.  
(699 mm)  
24-5/8 in.  
(625 mm)  
13-1/4 in.  
(337 mm)  
RF6M  
RF12M  
Roof Flashing Multi-pak  
Roof Flashing Multi-pak  
5 in.  
(127 mm)  
11-7/8 in.  
(302 mm)  
5 in.  
(127 mm)  
13-3/4 in.  
(349 mm)  
13-7/8 in.  
(352 mm)  
13-3/4 in.  
(349 mm)  
DVP-BEK2  
DVP-HPC Cap Brick Extension  
BEK  
Trap Cap Brick Extension  
11-5/8 in.  
(295 mm)  
12-1/8 in.  
(308 mm)  
7-1/8 in.  
(181 mm)  
5-3/4 in.  
(146 mm)  
DVP-TRAPFL  
COOL-ADDM  
Cap Shield  
Flashing  
13-7/8 in.  
(352 mm)  
9-1/2 in.  
(241 mm)  
26 in.  
660 mm  
14 in.  
(356 mm)  
DVP-HSM-B  
Extended Heat Shield  
DRC-RADIUS  
Cap Shield  
Figure 16.5 DVP vent components  
74  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Vent Components Diagrams (continued)  
7-3/8 in.  
(187 mm)  
1-1/2 in.  
(38 mm)  
17-3/4 in.  
(451 mm)  
14 in.  
(356 mm)  
LINK-DV-30B  
(LINK-DV-30)  
12 in.  
(305 mm)  
12 in.  
305 mm  
DVP-TB1  
BasementVent Cap  
7-1/4 in.  
(184 mm)  
12-1/2 in.  
(318 mm)  
5-1/4 in.  
(133 mm)  
DVP-TVHW  
VerticalTermination Cap (Highwind)  
PVK-80  
(Not compatible with Intellifire Plus™.)  
(For use with IPI and DSI appliances only.)  
7-1/4 in.  
(184 mm)  
14 in.  
(356 mm)  
16-7/8 in.  
(429 mm)  
1 in.  
(25 mm)  
12 in.  
(305 mm)  
14 in.  
(356 mm)  
7-1/8 in.  
12-1/8 in.  
(181 mm)  
(314 mm)  
3/8 in. (10 mm)  
1 in. (25 mm)  
8-3/4 in.  
(222 mm)  
7-3/4 to 10-3/8 in.  
(197 to 264 mm)  
1-5/8 in.  
(41 mm)  
DVP-FBHT  
FireBrickTermination Cap  
DVP High Performance Cap  
Figure 16.6 DVP vent components  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
75  
Optional Wire Harness  
13-5/8 in.  
346 mm  
DESCRIPTION  
PART NUMBER  
PVI-WH10  
10 ft. PV Wire Harness  
20 ft. PV Wire Harness  
40 ft. PV Wire Harness  
60 ft. PV Wire Harness  
80 ft. PV Wire Harness  
100 ft. PV Wire Harness  
PVI-WH20  
PVI-WH40  
12-1/2 in.  
318 mm  
PVI-WH60  
PVI-WH80  
PVI-WH100  
20-3/4 in.  
527 mm  
Note: Wire harnesses required to power the PVI-SLP  
connect to the appliance and are ordered separately  
from PVI-SLP. Contact your dealer to order.  
PVI-SLP  
Power Vent Inline  
16 in.  
406 mm  
15 in.  
(381 mm)  
4-1/2 in.  
114 mm  
9-3/16 in.  
(233 mm)  
13-5/8 in.  
(346 mm)  
16-11/16 in.  
(424 mm)  
16-11/16 in.  
424 mm  
12-1/2 in.  
(318 mm)  
SLP-LPC  
SLP Low Profile Cap  
76  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Vent Components Diagrams (continued)  
8-1/8 in.  
(206 mm)  
13 in.  
(330 mm)  
Effective Length  
5-3/4 to 8-3/8 in.  
146 to 213 mm  
5-1/2 in.  
140 mm  
8-3/8 in.  
213 mm  
3°  
87°  
15 in.  
(381 mm)  
10-1/2 in.  
267 mm  
10-7/8 in.  
276 mm  
WARNING  
Fire Risk.  
• When using DVP-HRC-SS and DVP-HRC-ZC-  
SS termination caps on top vented fireplaces, a  
6 inch minimum vertical vent section is required  
before installing first elbow.  
DVP-HRC-SS  
DVP-HRC-ZC-SS  
HORIZONTAL TERMINATION CAP  
COAXIAL to COLINEAR VENTING  
LINK-DV30B  
Flex Liner Kit  
768-380A  
Stainless Steel Flex Pipe  
DV-46DVA-GCL  
Coaxial/Colinear Appliance Connector  
DVP-2SL  
Adapter  
Figure 16.7 DVP vent components  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
77  
B. Vent Components Diagrams (continued)  
6-1/2 in.  
165 mm  
6-1/2 in.  
165 mm  
6-1/2 in.  
165 mm  
8-3/4 in.  
222 mm  
9-1/4 in.  
235 mm  
6 in.  
152 mm  
6-5/8 in.  
168 mm  
6-5/8 in.  
168 mm  
SLP45  
45° Elbow  
9-7/8 in.  
251 mm  
SLP90  
90° Elbow  
Effective  
Height/  
Length  
6-1/2 in.  
165 mm  
Effective Height/Length  
Pipe  
SLP4  
inches  
4
mm  
102  
SLP PIPE  
SLP6  
6
152  
SLP12  
SLP24  
SLP36  
SLP48  
SLP6A  
SLP12A  
12  
305  
25-3/16 in.  
640 mm  
24  
610  
36  
914  
48  
1219  
51 - 152  
51 - 305  
2 - 6  
2 - 12  
10-7/8 in.  
276 mm  
8-1/16 in.  
205 mm  
1-1/2 in.  
38 mm  
8-7/8 in.  
225 mm  
DVP-SLP24  
Adapter  
SLP-HVS  
Horizontal Pipe  
Support  
8-11/16 in.  
220 mm  
12 in.  
305 mm  
8-11/16 in.  
220 mm  
1-1/2 in.  
38 mm  
12 in.  
305 mm  
5-1/2 in.  
146 mm  
SLP-WS  
SLP-FS  
Wall Shield Firestop  
Ceiling Firestop  
Figure 16.8 SLP Series Vent Components  
78  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Vent Components Diagrams (continued)  
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be  
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)  
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a  
DVP-HSM-B will be required.  
8 in.  
(203 mm)  
Heat  
Shield  
15-1/8 in.  
(384 mm)  
Minimum  
Effective Length  
Maximum  
Effective Length  
Term Cap  
Trap1  
Max  
3-1/8 in.  
79 mm  
4-3/4 in.  
121mm  
9-1/4 in.  
235 mm  
Effective  
Length  
12 in.  
(305 mm)  
5-1/4 in.  
133 mm  
Trap2  
SLP-TRAP  
Horizontal Termination Cap  
6-3/8 in.  
4-3/16 in.  
163 mm  
106 mm  
4-5/8 in.  
117 mm  
4 in.  
102 mm  
5-1/16 in.  
128 mm  
8-1/8 in.  
206 mm  
DVP-2SL  
Adapter  
14-7/16 in.  
367 mm  
26 in.  
660 mm  
2-5/16 in.  
59 mm  
14-7/16 in.  
367 mm  
DVP-HSM-B  
Extended Heat Shield  
SLP-WT-BK  
Wall Thimble-Black  
Figure 16.9 SLP Series Vent Components  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
79  
B. Vent Components Diagrams (continued)  
13 in.  
14 in.  
330 mm  
356 mm  
1-5/16 in.  
34 mm  
13 in.  
330 mm  
10-9/16 in.  
269 mm  
SLP-DCF-BK  
Ceiling Firestop  
Black  
SLP-CCS-BK  
Cathedral Ceiling  
Support Box-Black  
10-11/16 in.  
271mm  
12 in.  
305 mm  
28-1/2 in.  
724 mm  
12-1/2 in.  
318 mm  
13-1/2 in.  
343 mm  
SLP-TVHW  
Vertical  
Termination Cap  
SLK-SNKD  
Snorkel  
Termination Cap  
Figure 16.10 SLP Series Vent Components  
80  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. Service Parts  
6000C, 6000C-IPI  
Beginning Manufacturing Date: Aug 2009  
36” Gas Fireplace - DV  
Ending Manufacturing Date: Active  
7
Log Set Assembly  
1
2
8
3
4
5
6
9
10  
14  
9.1  
13  
15  
11  
12  
16  
9.2  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
COMMENTS  
PART NUMBER  
Y
Log Set Assembly  
Log 1  
LOGS-6C  
1
2
3
4
5
6
7
8
SRV2164-701  
SRV2164-702  
SRV2164-703  
SRV2164-704  
SRV2164-705  
SRV2164-706  
2166-136  
Log 2  
Log 3  
Log 4  
Log 5  
Log 6  
Insulation Board  
Burner Top  
Burner NG  
Burner LP  
Air Scoop  
Pilot Cover  
Log Grate  
Base Refractory  
Refractory Basket  
Y
Y
Y
SRV2166-100  
2164-007  
9
2164-008  
9.1  
9.2  
10  
11  
2170-188  
2170-181  
2166-104  
SRV6BASE-STRAT  
2166-108  
12  
13  
14  
15  
16  
Y
Glass Door Assembly  
Surround Assembly  
GLA-6000G  
2166-019  
Finishing Strips (Sold as kit only)  
Junction Box  
SRVFS-6  
Y
4021-013  
Additional service part numbers appear on following page.  
9/12  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
81  
Service Parts  
8000C, 8000C-IPI  
Beginning Manufacturing Date: Aug 2009  
Ending Manufacturing Date: Active  
42” Gas Fireplace - DV  
7
Log Set Assembly  
8
1
2
3
4
6
5
9
10  
9.1  
14  
13  
15  
11  
12  
16  
9.2  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
COMMENTS  
PART NUMBER  
LOGS-8C  
Log Set Assembly  
Log 1  
Y
1
2
3
4
5
6
7
8
SRV2168-701  
SRV2168-702  
SRV2168-703  
SRV2168-704  
SRV2168-705  
SRV2168-706  
2170-136  
Log 2  
Log 3  
Log 4  
Log 5  
Log 6  
Insulation Board  
Burner Top  
Burner NG  
Burner LP  
Air Scoop  
Pilot Cover  
Log Grate  
Base Refractory  
Refractory Basket  
SRV2170-100  
2168-007  
Y
Y
Y
9
2168-008  
9.1  
9.2  
10  
11  
2170-188  
2170-181  
2170-104  
SRV8BASE-STRAT  
2170-108  
12  
13  
14  
15  
16  
Glass Door Assembly  
Surround Assembly  
GLA-950TR  
2170-019  
Y
Finishing Strips (Sold as kit only)  
Junction Box  
SRVFS-8  
4021-013  
Y
Additional service part numbers appear on following page.  
9/12  
82  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Parts  
6000C-IPI, 8000C-IPI  
Beginning Manufacturing Date: Aug 2009  
Ending Manufacturing Date: Active  
17.2  
#17 Valve Assembly  
17.1  
17.14  
17.15  
17.3  
17.13  
17.12  
17.4  
17.11  
17.7  
17.10  
17.9  
17.8  
17.6  
17.5  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
Shutter Bracket Assembly  
COMMENTS  
PART NUMBER  
17.1  
2166-157  
2166-370  
2166-371  
SRV485-301  
2118-420  
2118-104  
302-320A  
2166-302  
2166-303  
303-315/5  
2166-119  
2187-198  
2166-323  
2118-170  
2166-305  
2164-030  
2166-307  
2166-304  
582-837  
Y
Y
Y
Y
Pilot Assembly NG  
Pilot Assembly LP  
Pilot Tube  
17.2  
17.3  
17.4  
17.5  
3-hole Grommet  
Valve Bracket  
Flex Ball Valve Assembly  
Valve NG  
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
17.6  
Valve LP  
17.7  
17.8  
Male Connector  
Bulkhead W/Tube  
Jumper Wire  
Pkg of 5  
17.9  
17.10  
17.11  
17.12  
17.13  
17.14  
17.15  
Battery Pack **  
Thermostat Wire Assembly  
Transformer  
Control Assembly  
Module  
Wire Harness  
Burner Orifice NG (#37C)  
Burner Orifice LP (#52C)  
Burner Orifice NG (#33C)  
Burner Orifice LP (#50C)  
6000C-IPI  
8000C-IPI  
582-852  
582-833  
582-850  
**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 500mA~10A 3/4" long  
Additional service part numbers appear on following page.  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
83  
Service Parts  
6000C, 8000C  
Beginning Manufacturing Date: Aug 2009  
Ending Manufacturing Date: Jan 2010  
#17 Valve Assembly  
17.1  
17.2  
17.3  
17.4  
17.5  
17.10  
17.6  
17.9  
17.8  
17.7  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
Shutter Bracket Assembly  
COMMENTS  
PART NUMBER  
17.1  
2166-157  
2103-010  
2103-011  
SRV485-301  
2103-512  
446-511  
Y
Y
Y
Y
Y
Y
Pilot Assembly NG  
Pilot Assembly LP  
Pilot Tube  
17.2  
Thermopile  
Thermocouple  
17.3  
17.4  
17.5  
17.6  
3-hole Grommet  
Valve Bracket  
Flex Ball Valve Assembly  
Piezo Ignitor  
2118-420  
2118-104  
302-320A  
291-513  
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Valve NG  
2166-300  
2166-301  
303-315/5  
2166-119  
2045-024  
582-837  
17.7  
Valve LP  
17.8  
17.9  
Male Connector  
Bulkhead W/Tube  
Pkg of 5  
17.10 Thermostat Wire Assembly  
Burner Orifice NG (#37C)  
6000C  
8000C  
Burner Orifice LP (#52C)  
582-852  
Burner Orifice NG (#33C)  
582-833  
Burner Orifice LP (#50C)  
582-850  
Wire Assembly  
040-557A  
Additional service part numbers appear on following page.  
84  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Parts  
6000C, 8000C  
Beginning Manufacturing Date: Aug 2009  
Ending Manufacturing Date: Active  
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement  
parts for your appliance please provide model number and serial number. All parts listed  
in this manual may be ordered from an authorized dealer.  
Stocked  
at Depot  
ITEM  
DESCRIPTION  
COMMENTS  
PART NUMBER  
385-105  
Exhaust Shield  
Flue Restrictor  
Gasket Assembly  
385-128  
2166-081  
Contains Vent, Burner Neck, Valve Plate, LED and Adjustable Air Shutter Gaskets  
Glass Latch Support  
Mineral Wool  
Pkg of 2  
33858/2  
Y
050-721  
Touch Up Paint  
TUP-GBK-12  
Standing Pilot Conversion Kits  
Conversion Kit NG  
Conversion Kit LP  
Conversion Kit NG  
Conversion Kit LP  
Regulator NG  
NGKS-6C  
LPKS-6C  
Y
Y
Y
Y
Y
Y
Y
Y
6000C  
NGKS-8C  
LPKS-8C  
8000C  
NGK-SITV-50  
LPK-SITV-50  
2103-116  
Regulator LP  
Pilot Orifice NG  
Pilot Orifice LP  
2103-117  
IPI Conversion Kits  
Conversion Kit NG  
Conversion Kit LP  
Conversion Kit NG  
Conversion Kit LP  
Regulator NG  
NGKI-6C  
LPKI-6C  
Y
Y
Y
Y
Y
Y
Y
Y
6000C-IPI  
8000C-IPI  
NGKI-8C  
LPKI-8C  
NGK-DXV-50  
LPK-DXV-50  
593-528  
Regulator LP  
Pilot Orifice NG  
Pilot Orifice LP  
593-527  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
85  
D. Contact Information  
Heat & Glo, a brand of Hearth & Home Technologies Inc.  
7571 215th Street West, Lakeville, MN 55044  
www.heatnglo.com  
Please contact your Heat & Glo dealer with any questions or concerns.  
For the location of your nearest Heat & Glo dealer,  
please visit www.heatnglo.com.  
- NOTES -  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
________________________________________________________________________________  
NOTICE  
DO NOT DISCARD THIS MANUAL  
• Important operating  
and maintenance  
instructions included.  
• Read, understand and follow  
these instructions for safe  
installation and operation.  
• Leave this manual with  
party responsible for use  
and operation.  
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,  
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,  
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.  
2000-945  
Printed in U.S.A. - Copyright 2012  
86  
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Inc Paint Sprayer 224200 User Manual
Haier Dishwasher DW12 HFE2ME User Manual
Hasbro Portable Stereo System GES 3+ User Manual
Hasbro Robotics 51472 User Manual
Honeywell Marine Radio V4043 User Manual
HP Hewlett Packard Computer Monitor B132L+ User Manual
HP Hewlett Packard Printer 1055CMHP User Manual
Hunter Fan Fan 23845 User Manual
Husqvarna Lawn Mower 5118761 06 User Manual
Image Treadmill IMTL11994 User Manual