10” Heavy-Duty 15 aMP
table Saw
66630
Set uP anD OPerating inStructiOnS
®
Distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
Save tHiS Manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
glasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and it
frees both hands to operate tool.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
recOMMenDeD MiniMuM wire
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
gauge FOr eXtenSiOn cOrDS
(120 vOlt)
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and chang-
ing accessories.
eXtenSiOn cOrD
lengtH
naMePlate
aMPereS
(at full load)
25’
50’ 100’ 150’
0 – 6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
6.1 – 10
15. DISCONNECT TOOLS before ser-
vicing; when changing accessories,
such as blades, bits, cutters, and the
like.
10.1 – 12
12.1 – 16
table a
Do not use.
9. USE PROPER EXTENSION CORD.
Make sure your extension cord is
in good condition. When using an
extension cord, be sure to use one
heavy enough to carry the current
your product will draw. An undersized
cord will cause a drop in line voltage
resulting in loss of power and over-
heating. Table A shows the correct
size to use depending on cord length
and nameplate ampere rating. If in
doubt, use the next heavier gage.
The smaller the gage number, the
heavier the cord.
16. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
17. USE RECOMMENDED ACCESSO-
RIES. Consult the owner’s manual for
recommended accessories. The use
of improper accessories may cause
risk of injury to persons.
18. NEVER STAND ON TOOL. Serious
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewelry
which may get caught in moving
parts. Nonslip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
19. CHECK DAMAGED PARTS. Before
further use of the tool, a guard or
other part that is damaged should
be carefully checked to determine
that it will operate properly and per-
form its intended function – check for
alignment of moving parts, binding
of moving parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
or other part that is damaged should
be properly repaired or replaced.
b. Through-sawing – A cut made from
one side of a board to the opposite
side, without stopping.
20. DIRECTION OF FEED. Feed work
into a blade or cutter against the
direction of rotation of the blade or
cutter only.
c. Ripcut or Ripping - A cut made paral-
lel to (along with) the grain of the
wood.
d. Crosscut or Crosscutting - A cut
made perpendicular (at a 90° angle)
to the grain of the wood.
21. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a
complete stop.
e. Push-stick – A narrow strip of wood
or other soft material with a notch
cut into one end and which is used
to push short pieces of material
through saws. It provides a safe
distance between the hands and the
cutting tool. Must be narrower than
the cut width to prevent contact with
the blade.
table Saw Safety warnings
For your Own Safety read instruction
Manual before Operating Saw
1. Wear eye protection.
2. Use saw-blade guard and spreader
for every operation for which it can be
used, including all through sawing.
f. Freehand – Feeding a workpiece
through the saw without using a
fence or guided support to guide it.
nOt a SaFe MetHOD.
3. Keep hands out of the line of saw
blade.
g. Kerf – The gap made by the saw in
the workpiece.
4. Use a push-stick when required.
h. Kickback – A sudden reaction to a
pinched, bound, or misaligned blade,
causing an uncontrolled workpiece
to lift up and out of the saw toward
the operator.
5. Know how to reduce risk of kickback.
6. Do not perform any operation free-
hand.
7. Never reach around or over saw
blade.
i. Spreader – A metal plate that fol-
lows the saw blade to keep the kerf
(gap) from closing on the saw blade.
Spreaders, except riving knives,
must be aligned to the blade after
blade adjustment to prevent binding.
8. Make sure the workpiece is support-
ed at all times while sawing. Use a
roller stand (not provided) with larger
workpieces if necessary.
j. Riving Knife – A spreader mounted
on the same mechanism as the
blade. Generally more effective than
simple spreaders.
9. To properly understand all safety
warnings, be familiar with the follow-
ing safety terms and equipment:
a. Featherboard – A block with “fingers“
that hold the workpiece against the
fence while sawing.
10. As noted previously, Kickback is a
sudden reaction to a pinched, bound,
or misaligned blade, causing an un-
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
controlled workpiece to lift up and out
of the saw toward the operator.
Kickback is usually a result of tool
misuse and can be limited or avoided
by following the precautions below:
movable guard does not move freely
and close instantly. Make sure any
movable guard does not touch the
blade in all angles, depths of cut, and
positions.
• Fence must be completely parallel
to the saw blade.
12. Keep the guard in place while
through-sawing. Verify that the
spreader lines up with the blade to
prevent binding.
• Workpiece must be free from flaws
(such as loose knots) and from
foreign objects (such as nails and
screws).
13. Construct a Push Stick out of Wood
according to the guidelines on the fol-
lowing page The use of accessories
or attachments not recommended by
the manufacturer may result in a risk
of injury to persons. See next page
for Push Stick Features and Func-
tions.
• Support large workpieces along
their entire length. Large workpiec-
es tend to bend, grabbing the blade.
• Do not use a dull, damaged, or
pitch-covered blade.
• Do not use fence as a guide when
crosscutting.
• Do not ripcut a twisted or warped
workpiece, or workpiece without
straight edge to guide along fence.
• Maintain control of the workpiece.
Do not allow the workpiece to rest
against the moving blade without
holding onto it.
• If the blade binds or a cut is inter-
rupted, turn off the power switch
and hold the workpiece still until the
blade stops. Correct the cause of
blade binding before proceeding.
• Before continuing an unfinished
cut, center the blade in the pre-cut
kerf and check that the saw teeth
are not engaged into the workpiece
before turning on the saw.
• Push the wood stock past the blade
prior to release.
11. Check guards for proper operation
with saw disconnected from power
before each use. Do not disable any
guard. Do not operate saw if any
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
essential Straight Push-stick Features and
Functions
note: Straight style (traditional) stick shown. A dif-
ferent stick design may be used if it properly
protects against all hazards.
Handle notch
• Must be far
enough down
the stick to allow
a comfortable and
firm grip.
Diagram not to scale.
• Push sticks must be made from sturdy, defect-free,
plywood or normal wood to prevent unexpected
breakage. Material must be at least 1/4” thick ,but
no thicker than the finished wood.
• Must be deep enough
to prevent hand from
slipping down the
stick.
• Inspect push stick before use and do not use a
damaged or deteriorated push stick.
• Push stick dimensions will vary depending
on the application and user.
• Do not cut more than
halfway into the stick
to prevent weakening.
• Corners may be
rounded to increase
comfort.
Stick length
• Must be long enough
to prevent accidental
blade contact.
• At least 6” from end of
handle to closest part
of notch.
notch
• Must be right angle cut 30°-40° from the angle of the stick to
keep hands out of the line of the blade.
• The lower lip of the notch must be no longer than the workpiece
is thick.
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
14. When servicing use only identical
replacement parts.
chemicals known [to the State of Cali-
fornia] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and ce-
ment or other masonry products
• Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures var-
ies, depending on how often you do
this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
15. Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breath-
ing protection must be NIOSH-ap-
proved for the specific hazards in the
work area.
16. Industrial applications must follow
OSHA guidelines.
17. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
21. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
18. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
19. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:
22. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
• Avoid operating alone.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
vibration Safety
This tool vibrates during use. Re-
peated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
20. Some dust created by power sand-
ing, sawing, grinding, drilling, and
other construction activities, contains
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
reduce the risk of vibration-related
injury:
grOunDing inStructiOnS
tO Prevent
electric SHOcK
anD DeatH FrOM
incOrrect grOunDing
wire cOnnectiOn
reaD anD FOllOw tHeSe
inStructiOnS:
1. Anyone using vibrating tools regu-
larly or for an extended period should
first be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, ner-
vous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any medical or
physical symptoms related to vibra-
tion (such as tingling, numbness, and
white or blue fingers), seek medical
advice as soon as possible.
grounded tools: tools with three
Prong Plugs
1. In the event of a malfunction or
breakdown, grounding provides a
path of least resistance for electric
current to reduce the risk of electric
shock. This tool is equipped with an
electric cord having an equipment-
grounding conductor and a ground-
ing plug. The plug must be plugged
into a matching outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
2. Do not smoke during use. Nico-
tine reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
2. Do not modify the plug provided – if it
will not fit the outlet, have the proper
outlet installed by a qualified electri-
cian.
4. Use tools with the lowest vibration
when there is a choice between dif-
ferent processes.
3. Improper connection of the equip-
ment-grounding conductor can re-
sult in a risk of electric shock. The
conductor with insulation having an
outer surface that is green with or
without yellow stripes is the equip-
ment-grounding conductor. If repair
or replacement of the electric cord or
plug is necessary, do not connect the
equipment-grounding conductor to a
live terminal.
5. Include vibration-free periods each
day of work.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
4. Check with a qualified electrician or
service personnel if the grounding
Save tHeSe
inStructiOnS.
instructions are not completely under-
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
stood, or if in doubt as to whether the
tool is properly grounded.
Double insulated tools: tools
with two Prong Plugs
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and
3-pole receptacles that accept the
tool’s plug.
6. Repair or replace damaged or worn
cord immediately.
1. To reduce the risk of electric shock,
double insulated equipment has a po-
larized plug (one blade is wider than
the other). This plug will fit in a polar-
ized outlet only one way. If the plug
does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact
a qualified electrician to install the
proper outlet. Do not change the plug
in any way.
7. This tool is intended for use on a cir-
cuit that has an outlet that looks like
the one illustrated above in 125 v~
3-Prong Plug and Outlet. The tool
has a grounding plug that looks like
the plug illustrated above in 125 v~
3-Prong Plug and Outlet.
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
8. The outlet must be properly installed
and grounded in accordance with all
codes and ordinances.
9. Do not use an adapter to connect this
tool to a different outlet.
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
SPeciFicatiOnS
Electrical Requirements 120 V~ / 60 Hz / 15 A
Motor No Load Speed
Blade Diameter
4800 RPM
10”
assembly
Arbor Diameter
5/8”
Table Surface
16”x 26”
3”
To Install Handwheel (29)
Cutting Depth at 0°
Cutting Depth at 45°
Overload Protection
1. Remove the Bolt (27) from the Screw
Rod (54).
2-3/8”
Breaker Switch
2. Place the Handwheel onto the Screw
Rod. Fasten into place by using the
Bolt.
e105017
To Assemble Blade Guard (113)
unPacKing
1. Unplug the Saw and remove the
Switch Key (16).
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at the number shown on the
cover of this manual as soon as possible.
2. Position the Blade (96) 90° to the
table and lock in place.
3. Position the recessed end of the
Splitter Bracket (119) against the end
of the Pivot Plate (117) and fasten in
place using the Spring Washer (3),
Mat Washer (4) and Bolt (116).
inStructiOnS FOr
Putting intO uSe
read the entire iMPOrtant
SaFety inFOrMatiOn
Please note: Do not fully tighten the Bolt
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
at this time.
4. Remove the Wing Nut (121), Flat
Washer (50) and Spring Washer (3)
from Splitter Bracket.
tO Prevent
SeriOuS injury
FrOM acciDental
5. Position the Splitter (131) against the
Splitter Bracket. Make sure the tabs
on the Splitter Bracket are INSIDE
the slot of the Splitter.
OPeratiOn:
turn the Power Switch of the
tool to its “OFF” position,
remove key, and unplug the
tool from its electrical outlet
before assembling or making
any adjustments to the tool.
6. Replace the Wing Nut (121), Flat
Washer (50) and Spring Washer (3).
7. Make sure there is at least a 1/8” gap
between the bottom edge of the Split-
ter and the top surface of the Table
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
(109) and that the tabs are on the
INSIDE slot of the Splitter.
will allow sawdust to fall through the
Table Saw’s Base.
8. Use a framing square (not included)
to make sure the Saw Blade and
Splitter assembly are square. If not
square, loosen the Splitter Bracket
and adjust until the Splitter is properly
aligned with the Saw Blade. Then
tighten all screws and bolts.
6. Securely fasten the Table Saw to the
supporting surface using washers,
flat washers and nuts (hardware not
included.)
7. warning! Failure to provide this
sawdust removal hole will allow
sawdust to build up around the mo-
tor, which can potentially lead to a
fire hazard and/or damage the motor
assembly.
Mounting
1. The Saw MUST be properly secured
to the supporting surface using the
four mounting holes at each corner
of the Base (5).
OPerating inStructiOnS
read the entire iMPOrtant
SaFety inFOrMatiOn
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
2. If mounting Table Saw to a leg stand
(not included), insert screws through
the holes in each corner and into
the pre-drilled holes in the leg stand.
Tighten together using washers, flat
washers and nuts (hardware not
included.)
table Saw adjustments
3. If placing Table Saw on support sur-
face, insert the Rubber Feet (1) into
each corner of the Base to dampen
the vibration.
tO Prevent
SeriOuS injury
FrOM acciDental
OPeratiOn:
turn the Power Switch of the
tool to its “OFF” position,
remove key, and unplug the
tool from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
Please note: Before the Table Saw is
placed on supporting surface, please
verify that supporting surface has a
11”-12” square hole to allow for saw-
dust to fall through and be removed.
4. If the supporting surface does not
have the hole, square the Table Saw
on the supporting surface and mark
the location of the four 5/16” holes to
be drilled.
warning! check the blade
guard assembly before and
after every use.
5. Locate and mark an 11”-12” square
that is centered between the four
mounting holes. Once marked, cut
out and remove the square. This
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Depth and Angle Adjustment
7. Please note: When the Blade is
at 90° to the Table Saw, the Blade
should be square with the Saw Table.
1. The Blade (96) depth should be set
so that outer points of the Blade are
1/8” to 1/4” higher than the workpiece 8. warning! The Bevel Lock Knob
while the lowest points are below the
workpiece.
must be tightened during all cutting
operations.
2. To raise the Blade, turn the Hand-
wheel (29) counterclockwise.
45° and 90° Positive Stop Adjustment
1. The Table Saw is equipped with
positive stops for rapid and accurate
positioning of the Blade at 45° and
90° to the table.
3. To lower the Blade, turn the Hand-
wheel clockwise.
4. To adjust the Blade’s angle, loosen
the Bevel Lock Knob (62) and then
turn the Handwheel until the Blade
reaches the desired angle. Then
tighten the Bevel Lock Knob. See
Figure a, below.
2. Before making ANY adjustments,
make sure the Table Saw is un-
plugged and the Switch is removed.
3. To adjust the positive stop at 90°,
loosen the Bevel Lock Knob and
move as far to the left as possible.
Then tighten the Knob.
Bevel Lock
Knob (62)
4. Place a level or square (not included)
on the Table (109) with one end blade
to make sure Blade is at 90°. If not,
loosen the Bolt (110) a few turns and
tilt Blade until at the correct angle.
5. Tighten the Bevel Lock Knob and
then tighten the Bolt (110).
Handwheel
(29)
Switch (17)
6. To adjust the positive stop at 45°,
loosen the Bevel Lock Knob and and
move as far to the right as possible.
Then tighten the Knob.
Figure a
5. When the Blade is tilted to the left as
far as it will go, the Blade should be
at a 45° angle to the Saw Table and
the Bevel Indicator on the Ruler (13)
should point to 45°.
7. Place a level or square on the Table
with one end blade to make sure
Blade is at 45°. If not, loosen the Bolt
(111) a few turns and tilt Blade until at
the correct angle.
6. When the Blade is tilted to the right
as far as it will go, the Blade should
be at a 90° angle to the Saw Table
and the Bevel Indicator on the Ruler
should point to 0°.
8. Tighten the Bevel Lock Knob and
then tighten the Bolt (111).
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Aligning and Adjusting the Rip Fence (146)
with or slightly below the Table sur-
face.
1. warning! A misaligned Fence can
cause kickbacks and jams. To reduce
risk of injury, always maintain proper
Fence alignment. The Rip Fence
must be parallel with the Blade and
Table grooves.
Miter Gauge (100) Operation and
Adjustment
1. When straight cross-cutting (the
Blade is set at 90° to the Table) the
Miter Gauge can be used in either
table slot.
2. Lift up the Fence Handle (26) and
move the Fence along the gauge slot
until sliding it to the desired location.
2. When bevel cross-cutting (the Blade
is tilted away) only use the Miter
Gauge in the right table slot where
the Blade is titled away from the Miter
Gauge and your hands.
3. Verify that Fence is parallel, then
push down on the Handle to lock the
Fence in place.
4. A Draw Pole (132) locks the Fence
in place. To adjust the Draw Pole,
loosen the Bolt (20) that connects the
Draw Pole to the Fence.
3. To operate the Miter Gauge, loosen
the Gauge’s Lock Knob (101) and
move the Gauge to the desired angle,
then tighten Knob.
5. warning! The Fence must be
properly aligned to the gauge slot to
prevent kickback during ripping.
Adjusting Blade Parallel To Miter Gauge
Slots
1. warning! Make sure to unplug
Table Saw before making any adjust-
ments to Blade.
6. To check for proper alignment, po-
sition the Fence next to the gauge
slot and clamp Fence to the Table
by pushing down on Fence Handle.
Once locked, the edge of the Fence
should be parallel to the gauge slot.
2. To prevent kickback and ensure ac-
curate cuts when cutting, the Blade’s
angle in relation to the Miter Gauge
should be regularly checked. If any
adjustments are needed:
Adjusting Table Insert (112)
1. Lower the Blade by turning the Hand-
wheel clockwise.
3. Remove the Blade Guard (113).
4. Raise the Blade to its highest position
and adjust to Blade so that it is 90° to
the Table.
2. Loosen the two Table Insert Bolts
(12).
3. Adjust the Table Insert and retighten,
making sure to not overtighten. Do-
ing so can cause the Table Insert to
bow or bend.
5. Mark a Blade tooth at the front of the
Table Saw with a marker.
6. Using a square or ruler (not includ-
ed), place the square against the
Miter Gauge slot and adjust the flat
4. If the Table Insert is slightly above
the Table, tighten the two Table Insert
Bolts until the Table Insert is flush
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
edge of the square until it touches the
marked tooth.
FENCE (146)
7. Rotate the Blade and check the same
marked tooth at the rear of the Table
Saw.
FRONT
OF
TABLE
SAW
8. If the front and rear measurements
are not identical, have a qualified ser-
vice technician repair the Table Saw.
Wood
Block
Figure b
Installing/Replacing Saw Blade
1. warning! Make sure to unplug
Table Saw before making any install-
ing or replacing Blade.
7. Place the Outer Flange onto the Ar-
bor Shaft. Be sure the hollow side of
the Flange is against the Blade and
that all pieces are sung against the
arbor housing.
2. warning! Use only a 10” diameter
saw blade rated at 4800 RPM and
with a 5/8” arbor hole.
8. Thread the Arbor Nut back onto the
Arbor. Tighten with the Wrench
(145), turning the nut clockwise and
holding the Arbor steady with the Pin
Wrench.
3. Remove the Blade Guard, raise the
Saw Blade to its maximum height and
remove the Table Insert.
4. Use the Wrench (145) to keep the
Saw arbor from rotating while using
the Pin Wrench (147) to remove the
Arbor Nut. Turn the nut counterclock-
wise to remove. Then remove the
Outer Flange (97) and the Blade.
9. Rotate the Blade to make sure it
turns freely. Then lower the Blade.
10. Replace the Table Insert and retight-
en the Table Insert screw.
11. warning! Do not overtighten screw.
Doing so can cause the Table to bow
or bend, leading to serious injury.
5. Place new 10” Blade onto the Arbor
Shaft (94), making sure the teeth
point DOWN at the front of the Table
Saw.
6. warning! The teeth MUST point
down toward the front of the Table
Saw for proper operation. See Figure
b, above. Incorrect blade installation
can damage the Saw Blade, Table
Saw and/or workpiece.
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
because of overloading (such as cut-
ting stock too fast or when using a
dull blade), first turn the Switch to the
“OFF” position.
work Piece and work area Set up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
5. Remove the stock and check Blade
condition.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to al-
low free movement while working.
6. Let the motor cool for 3-5 minutes
and push the Reset Button (16),
which will reset the overload device.
Turn the motor on by turning the
Switch to “ON.”
7. warning! Be sure to immediately
turn off the Table Saw if the overload
protector stops the motor.
3. Secure loose work pieces using a
vise or clamps (not included) to pre-
vent movement while working.
Avoiding Kickback
4. There must not be hazardous ob-
jects, such as utility lines or foreign
objects, nearby that will present a
hazard while working.
1. The Table Saw can be used for
straight-line cutting, such as cross
cutting, ripping, mitering, beveling
and compound cutting. However,
kickback can occur when the Blade
stalls, a cut is made at an incorrect
depth, or you saw into a knot or nail.
To avoid kickback, do the following:
general Operating instructions
1. The ON/OFF Switch (17) is located
on the Table Saw’s front panel. To
activate the Table Saw, turn the
switch to “ON”. To turn off the Table
Saw, turn the switch to “OFF.”
2. Use the correct blade depth setting.
The top blade teeth should clear the
workpiece by 1/8” to 1/4”.
2. When the Table Saw is “OFF,” keep
the Switch locked in the OFF posi-
tion. Do this by grasping the Switch
and pulling it out of the Switch Box
(21). The Table Saw will not operate
with the Switch removed.
3. Inspect the workpiece for knots or
nails before beginning a cut. Knock
out any loose knots with a hammer
and do not saw into loose knot or
nail.
4. Use the Fence when rip cutting and
the Miter Gauge when cross-cutting.
3. Please note: The Switch can be
removed while the Table Saw is run-
ning. But it cannot be restarted with-
out inserting the Switch back into the
Switch Box.
5. Use clean, sharp and properly-set
blades. Do not use dull blades.
6. Support the workpiece properly to
avoid pinching.
4. The Table Saw is also equipped with
a manual reset overload protector.
If the motor shuts off or fails to start
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
7. When making a cut, use steady and
even pressure. Do not force cuts.
Hand furthest from Blade on the
workpiece.
8. Do not cut wet or warped lumber.
9. Once cut is made, turn off Table Saw.
Wait for Blade to come to complete
stop before removing any part of
workpiece.
9. Hold the workpiece firmly with both
hands or use the included Push Stick.
(53). Make sure the Push Stick is
narrower than the workpiece and has
90° notch on one end and shaping for
a grip on the other end.
Making a Rip-cut
1. Turn the Handwheel counterclock-
wise until Blade is set to correct
depth of workpiece.
10. A push block (not included) can be
used with non-through cuts. cau-
tiOn: Make sure the push block’s
screws are recessed before using on
Table Saw.
2. Set the Blade to 0° and position
Fence at desired distance from Blade
for cut. Lock Fence in place.
3. Place a support (not included) that
is the same height as the Table Saw
behind the Saw.
Making a Cross-cut
1. warning! Using the Fence as a
cutoff gauge when cross-cutting will
result in kickback, which can lead to
serious injury and property damage.
4. Make sure wood is clear of Blade
before turning on Table Saw.
5. Use Push Stick or push block to
move the wood through the cut and
past the Blade. warning! Do not
push a small piece of wood into the
Blade with your hand. Always use
Push Stick or push block. See Fig-
ure c, below.
2. Remove the Fence.
3. Turn the Handwheel counterclock-
wise until the Blade is set at the cor-
rect depth for the workpiece.
4. Set the Miter Gauge at the desired
angle and lock into place using the
Adjusting Knob.
BLADE GUARD
(113)
5. Place a support (not included) that
is the same height as the Table Saw
behind the Saw.
BLADE (96)
FENCE (146)
6. Turn the Switch to “ON.”
WORKPIECE
CUT LINE
7. Let the Blade build up to full speed
before moving the workpiece into the
Blade from the front of the Saw.
PUSH STICK
(53)
8. warning! To prevent injury, place
hand closest to Blade on the Miter
Gauge Adjusting Knob and keep
Figure c
(view FrOM abOve)
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
To reduce possible injury should
kickback occur, stand to side of the
workpiece as it contacts the Blade.
warning! Do not stand in the line
of cut.
Fence and surface of Blade. If ripping
a narrow workpiece, use Push Stick
to move piece through cut and past
the Blade.
9. Once cut is made, turn off Table Saw.
Wait for Blade to come to complete
stop before removing any part of
workpiece.
6. Once cut is made, turn off Table Saw.
Wait for Blade to come to complete
stop before removing any part of
workpiece.
10. After the Blade has fully stopped,
remove the cutoff stock.
Making a Bevel Rip-cut
1. warning! The Fence must be on
the right side of the Blade to avoid
trapping the wood and causing kick-
back. Placing the Fence to the left of
the Blade with result in kickback and
lead to potential injury and property
damage.
2. If ripping a piece larger than 36” long,
place a support that is the same
height as the table behind the saw to
support the workpiece.
3. Keep wood clear of Blade before
turning on Table Saw.
4. Position workpiece flat on Table with
the edge flush against the Fence. Let
Blade build up to full speed before
feeding workpiece into Blade.
5. Use Push Stick or push block to
slowly feed workpiece toward the
Blade from the front.
6. warning! Stand slightly to the side
of the wood to reduce chance of
injury.
7. Once Blade has made contact with
the workpiece, use the hand closer to
Fence to guide it.
8. Make sure edge of workpiece re-
mains in solid contact with both
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. To maintain the surface of the Table,
periodically apply paste wax and
buff to keep Table surface smooth.
warning! Do not wax the working
face of Miter Gauge. Doing so may
cause a workpiece to slip during cut-
ting, leading to possible injury.
Maintenance anD
Servicing
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
5. aFter uSe, clean out sawdust from
underneath Table Saw and in Blade
teeth. Use a resin solvent on the
blade teeth. Dry with soft cloth.
tO Prevent
SeriOuS injury
FrOM acciDental
OPeratiOn:
turn the Power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
6. Use soft, damp cloth to clean plastic
parts. warning! Do not use any
aerosol or petroleum-based solvents.
Doing so can weaken or destroy
plastic, causing property damage and
leading to potential personal injury.
7.
warning! if the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
tO Prevent SeriOuS
injury FrOM tOOl
Failure:
Do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
cleaning, Maintenance, and
lubrication
1. beFOre eacH uSe, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
2. Check the Blade Guard assembly
before and after every use.
3. aFter uSe, clean external surfaces
of the tool with clean cloth. .
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
PartS liSt
PartS liSt
Part
Description
Qty.
4
5
8
13
1
5
2
1
9
1
11
1
4
3
1
1
2
1
1
1
1
2
2
2
1
3
1
3
2
1
1
1
4
1
1
1
1
2
4
12
7
4
1
3
3
1
4
1
1
1
1
Part
Description
Qty.
1
1
3
1
2
1
2
1
1
1
1
1
1
1
2
2
1
1
2
4
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
6
1
6
1
2
3
4
5
7
8
9
Rubber feet
55 Pointer
Bolt M6×25
Spring washer
Mat washer
Base
Bolt ST4.2×14
Sheathing
56 Pointer base
57 Lock nut M6
58 Bolt M6×16
59 Lock nut M8
60 Switch box mat
61 Line button
62 Bevel lock knob
63 Axis cover
64 Bolt M6×30
65 Turn axis
Cable press plate
10 Bolt M4×16
11 Strengthen plank
12 Bolt M4×8
13 Ruler
14 Nut M4
15 Washer
16 Switch Key
17 Switch
19 Bolt ST4.8X20
20 Bolt
21 Switch box
22 Bolt
23 Power cord
24 Handle cover
25 Bolt M6×45
26 Handle
66 Mat piece
67 Support iron
68 Bolt M5×20
69 Bolt
70 Bolt
71 Linkage plate
72 Down-load
73 Brush cover
74 Carbon brush
75 Brush hold
76 Bolt
77 Input wind cover
78 Motor cover
79 Stator
80 Block wind circle
81 Bearing
82 Rotor
83 Bearing
84 Middle cover
85 Bearing
86 Spring block circle
87 Gear
88 Half circle key
89 Output axis
90 Spring block circle
91 Bearing
92 Front cover
93 Bolt M5×20
94 Arbor Shaft
96 Blade
97 Outer flange
98 Nut M14X1.5
99 Dial pointer
100 Miter Gauge
101 Miter Gauge Lock Knob
102 Mat plate
103 Column pin
104 Angle ruler button
105 Axis flange
106 Ruler
27 Bolt M6×16
28 Nut M6
29 Handwheel
30 Spring washer
31 Mat washer
32 Block plank
33 Bolt M6×85
34 Steel pipe
35 Lock nut M6
36 Front stand
37 Rear stand
38 Column pin
39 Steel pipe C
40 Column pin
41 Bolt
42 Mat washer
43 Spring washer
44 Bolt M5×14
45 Mat plate
46 Bolt M6×18
47 Big washer
48 Pin
49 Nut M10
50 Flat washer
51 Pointer
52 Steel pipe B
53 Push Stick
54 Screw rod
1
108 Bolt M6×20
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
PartS liSt
PartS liSt
Part
109 Table
Description
Qty.
1
Part
131 Splitter
Description
Qty.
1
110 Bolt M6×25
111 Bolt M6×35
112 Table insert
113 Blade Guard
114 Bolt M6×12
115 Nut M6
116 Pivot Bolt M6×50
117 Pivot Plate
118 Bolt M6X16
119 Splitter Bracket
120 Bolt M6×12
121 Wing Nut M6
122 Twist spring
123 Axis cover2
124 Block plate
125 Quakeproof mat
126 Bolt M6×40
127 Armature
1
1
1
1
2
2
1
1
1
1
4
1
1
2
1
1
132 Draw pole
133 Clamp plate
134 Press spring
135 Ruler mat
136 Clamp plate
137 Spring piece
138 Wheel
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
140 Pin1
141 Pin2
142 Ruler stand
143 Bolt M6X12
144 Lock mat
145 Spanner
146 Rip Fence
147 Pin Wheel
148 Mat washer
149 Bolt M5X10
150 Nut M6
1
2
2
1
128 Axis cover3
129 Column pin
130 Spring column pin
2
1
1
151 Bolt M4×10
152 Bolt M4×10
153 Bolt M5X10
1
3
8
PleaSe reaD tHe FOllOwing careFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
record Product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
aSSeMbly DiagraM
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
liMiteD 1 year / 90 Day warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free of defects in materials and workmanship. Har-
bor Freight Tools also warrants to the original purchaser, for a period of one year from
date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship (90 days if used by a professional contractor or
if used as rental equipment). This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable
for death, injuries to persons or property, or for incidental, contingent, special or con-
sequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 66630
For technical questions, please call 1-800-444-3353.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
|