1 HP MINI DUST COLLECTOR
31810
SET UP aND OPERaTINg INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE THIS MaNUaL.
Copyright© 2001, 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
4. Remove adjusting keys or wrench-
es before turning the power tool
on. A wrench or a key that is left at-
tached to a rotating part of the power
tool may result in personal injury.
5. Do not abuse the Power Cord.
Never use the Power Cord to carry 5. Do not overreach. Keep proper
the tools or pull the Plug from an
outlet. Keep the Power Cord away
from heat, oil, sharp edges, or
moving parts. Replace damaged
Power Cords immediately. Dam-
aged Power Cords increase the risk
of electric shock.
footing and balance at all times.
Proper footing and balance enables
better control of the power tool in
unexpected situations.
6. Use safety equipment. always
wear eye protection. Dust mask,
nonskid safety shoes, hard hat, or
hearing protection must be used for
appropriate conditions.
6. When operating a power tool out-
side, use an outdoor extension
cord marked “W-a” or “W”. These
extension cords are rated for outdoor
use, and reduce the risk of electric
shock.
TOOL USE aND CaRE
1. Use clamps (not included) or other
practical ways to secure and sup-
port the workpiece to a stable
platform. Holding the work by hand
or against your body is unstable and
may lead to loss of control.
PERSONaL SaFETY
1. Stay alert. Watch what you are do-
ing, and use common sense when
operating a power tool. Do not use
a power tool while tired or under
the influence of drugs, alcohol, or
medication. A moment of inatten-
tion while operating power tools may
result in serious personal injury.
2. Do not force the tool. Use the cor-
rect tool for your application. The
correct tool will do the job better and
safer at the rate for which it is de-
signed.
3. Do not use the power tool if the
Power Switch does not turn it on
or off. Any tool that cannot be con-
trolled with the Power Switch is dan-
gerous and must be replaced.
2. Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
can be caught in moving parts.
4. Disconnect the Power Cord Plug
from the power source before
making any adjustments, changing
accessories, or storing the tool.
Such preventive safety measures
reduce the risk of starting the tool ac-
cidentally.
3. avoid accidental starting. Be sure
the Power Switch is off before
plugging in. Carrying power tools
with your finger on the Power Switch,
or plugging in power tools with the
Power Switch on, invites accidents.
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Store idle tools out of reach of chil-
dren and other untrained persons.
Tools are dangerous in the hands of
untrained users.
SPECIFIC SaFETY RULES
1. Wear aNSI-approved safety impact
eye goggles, hearing protection,
and a dust mask or respirator
6. Maintain tools with care. Keep cut-
ting tools sharp and clean. Prop-
erly maintained tools with a sharp
cutting edge are less likely to bind
and are easier to control. Do not use
a damaged tool. Tag damaged tools
“Do not use” until repaired.
when operating this product.
2. The Housing contains a high speed
Impeller that can amputate fingers,
grab loose clothing and long hair,
and propel sawdust at high velocities.
NEVER operate this product without
the all guards and screens in place
and working properly.
7. Check for misalignment or binding
of moving parts, breakage of parts,
and any other condition that may
affect the tool’s operation. If dam-
aged, have the tool serviced before
using. Many accidents are caused
by poorly maintained tools.
3. If using this product to help keep
airborne sawdust within acceptable
limits, you must regularly monitor air-
borne sawdust and maintain the Tool
to avoid exceeding dust limits. Each
application is unique, and your main-
tenance schedule must be tailored to
your specific use.
8. Use only accessories that are
recommended by the manufac-
turer for your model. Accessories
that may be suitable for one tool may
become hazardous when used on
another tool.
4. Industrial applications must follow
OSHA requirements.
5. Use the right tool or attachment
for the right job. Do not attempt to
force a small tool or attachment to
do the work of a larger industrial tool.
There are certain applications for
which this product was designed. It
will do the job better and more safely
at the rate for which it was intended.
Do not modify this product, and do
not use this product for a purpose for
which it was not intended.
SERVICE
1. Tool service must be performed
only by qualified repair personnel.
Service or maintenance performed by
unqualified personnel could result in
a risk of injury.
2. When servicing a tool, use only
identical replacement parts. Fol-
low instructions in the “Inspec-
tion, Maintenance, And Cleaning”
section of this manual. Use of
unauthorized parts or failure to follow
maintenance instructions may create
a risk of electric shock or injury.
6. Turn off the Tool and unplug the
Power Cord Plug from its electrical
outlet before changing accessories
or performing inspection, mainte-
nance, or cleaning procedures.
7. People with pacemakers should
consult their physician(s) before use.
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure.
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
8. WARNING: This product contains
or, when used, produces a chemi-
cal known to the State of California
to cause cancer and birth defects or
other reproductive harm. (California
Health & Safety Code § 25249.5, et
seq.)
grounded Tools: Tools with Three
Prong Plugs
9. The warnings, precautions, and
instructions discussed in this manual
cannot cover all possible conditions
and situations that may occur. The
operator must understand that com-
mon sense and caution are factors
which cannot be built into this prod-
uct, but must be supplied by the
operator.
3-Prong Plug and Outlet
10. Maintain labels and nameplates
on the Tool. These carry important
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
1. Tools marked with “Grounding Re-
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break
down, grounding provides a low
resistance path to carry electricity
away from the user, reducing the risk
of electric shock. (See 3-Prong Plug
and Outlet.)
SaVE THESE
INSTRUCTIONS.
gROUNDINg
TO PREVENT
ELECTRIC SHOCK
aND DEaTH FROM
INCORRECT gROUNDINg
WIRE CONNECTION:
Check with a qualified
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. Never
2. The grounding prong in the plug is
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-Prong Plug
and Outlet.)
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
7. Make sure the extension cord is prop-
erly wired and in good electrical con-
dition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
Extension Cords
RECOMMENDED MINIMUM WIRE
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
gaUgE FOR EXTENSION CORDS*
(120/240 VOLT)
EXTENSION CORD
NaMEPLaTE
LENgTH
aMPERES
(at full load)
2. As the distance from the supply outlet
increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and pos-
sible tool damage.
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
(See Table a.)
-
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table a.)
-
-
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TaBLE a
Symbology
4. When using more than one exten-
sion cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table a.)
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table a.)
V~
a
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPaCKINg
aSSEMBLY INSTRUCTIONS
When unpacking, check to make sure NOTE: For additional information regard-
all that all the parts listed in the Parts List
near the end of the manual are included.
If any parts are missing or broken, please
call Harbor Freight Tools at 1-800-444-
3353 as soon as possible.
ing the parts mentioned in the fol-
lowing pages, refer to the assembly
Diagram near the end of the man-
ual.
1. Remove the Lock Washers (33a) and
Nuts (34) from the Caster (25) Studs.
35
33a
34
25
2. Thread a Nut (34) back onto a Cast-
er’s stud securely.
3. Insert the Caster’s stud into a hole at
the bottom of the Frame (2).
4. Slide a Lock Washer (33a) onto the
stud. Secure the Caster in place us-
ing an Acorn Nut (35).
5. Repeat steps 2 through 4 above for
all Casters.
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERaTINg INSTRUCTIONS INSPECTION, MaINTENaNCE,
aND CLEaNINg
NOTE: For additional information regard-
ing the parts mentioned in the fol-
lowing pages, refer to the assembly
Diagram near the end of the man-
ual.
WaRNINg! Always make sure the Power
Switch is in its “OFF” position, and
unplug the Power Cord/Plug from its
120 volt electrical outlet before per-
forming any inspection, adjustments,
maintenance, or cleaning.
1. Turn the Power Switch off. Then,
plug the Power Cord Plug into the
nearest 120 volt, grounded, electrical
outlet.
1. Before each use, inspect the general
condition of the Tool. Check for loose
screws, misalignment or binding of
moving parts, cracked or broken
2. Connect the Dust Collector to a
woodworking machine’s dust port us-
parts, damaged electrical wiring, and
ing appropriate dust collection hoses
any other condition that may affect
and clamps (sold separately), then
its safe operation. If abnormal noise
turn the Dust Collector on. After, turn
or vibration occurs, have the problem
on the machine.
corrected before further use.
CaUTION: Only attach this dust collec-
tor to a woodworking machine.
Do not use damaged equipment.
2. Daily: With a soft brush, cloth, or
vacuum, remove all dust and debris
from the exterior of the Tool.
3. When finished using the Dust Collec-
tor turn it off. Unplug the Power Cord
Plug from its electrical outlet. Then
store the Dust Collector in a safe,
clean, dry location out of reach of
children and unauthorized users.
3. CaUTION! All maintenance, ser-
vice, or repairs not listed in this
manual are only to be attempted by a
qualified service technician.
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEaSE REaD THE FOLLOWINg CaREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUY-
ER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
PaRTS LIST
Part
1
Description
Housing
Qty.
1
Part
26
Description
Round Head Screw
Qty.
6
2
3
4
8
Frame
Inlet Screen
Inlet
Reducing Inlet
Outlet Screen
Outlet
1
1
1
1
1
1
27
28
29
30
31
32
Bolt
Bolt
Bolt
Bolt
Bolt
Nut
5
5
4
4
2
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Clamp
Collection Bag
Handle
Handle Cover
Power Cord
Strain Relief
Motor
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
33a Lock Washer
4
4
4
1
8
8
1
9
9
1
1
1
1
1
34
35
36
37
38
39
40
41
42
44
45
46
47
Nut
Acorn Nut
Flat Washer
Flat Washer
Flat Washer
Lock Washer
Lock Washer
Lock Washer
Direction Arrow
Nameplate
Bolt
Switch
Pin
Motor Shaft Packing
Motor Supported Flange
Motor Flange Packing
Fan
Fan Retainer
Caster
Sponge Packing
Sleeve
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
aSSEMBLY DIagRaM
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 1 YEaR / 90 DaY WaRRaNTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free of defects in materials and workmanship. Har-
bor Freight Tools also warrants to the original purchaser, for a period of one year from
date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship (90 days if used by a professional contractor or
if used as rental equipment). This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable
for death, injuries to persons or property, or for incidental, contingent, special or con-
sequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 31810
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
|