Geared Head
drill / Mill MacHine
42827
Set up and OperatinG inStructiOnS
distributed exclusively by Harbor Freight tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS Manual.
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
cover revised 09b
Download from Www.Somanuals.com. All Manuals Search And Download.
SafetY WaRninG & caUtionS
ReaD aLL inStRUctionS BefoRe USinG thiS tooL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations.
Don’t expose to rain. Keep work area well lit. Do not use electrically powered equipment in the presence
of flammable gases or liquids.
3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them handle
machines, tools, or equipment.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was
intended. Do not use inappropriate attachments in an attempt to exceed the tool’s capacities.
6. USE THE RIGHT TOOL FOR THE JOB. Do not use a tool for a purpose for which it was not
intended.
7. DRESS PROPERLY. Do not wear loose clothing or jewelry, as they can be caught in moving parts.
Non-skid footwear is recommended. Wear restrictive hair covering to contain long hair. Always wear
appropriate work clothing.
8. USE EYE, EAR AND BREATHING PROTECTION. Always wear ANSI approved impact safety
goggles if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or
respirator when working around metal, wood, and chemical dusts and mists. Use ANSI approved ear
protection when working in a loud or noisy environment.
9. DO NOT ABUSE THE POWER CORD. Protect the power cord from damage, either from impacts,
pulling or corrosive materials. Do not yank machine’s cord to disconnect it from the receptacle.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across
running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect power cord periodically and, if
damaged, have it repaired by an authorized technician. Inspect all hydraulic seals for leaks prior to use.
Control handle and power switch must be kept clean, dry, and free from oil and grease at all times.
12. REMOVE ADJUSTING KEYS AND WRENCHES. Be sure that keys and adjusting wrenches are
removed from the tool or machine work surface before operation.
13. AVOID UNINTENTIONAL STARTING. Be sure that you are prepared to begin work before turning
the start switch on.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
14. STAY ALERT. Watch what you are doing. Do not operate this machine when you are tired.
15. DO NOT OPERATE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL,
DRUGS, OR PRESCRIPTION MEDICINES.
16. CHECK FOR DAMAGED PARTS. Before using any tool, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment and binding of moving parts, any broken parts or mounting fixtures, and any other condition
that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a
qualified technician. Do not use the tool if any switch does not turn on and off properly.
17. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement
parts intended for use with this tool. Replacement parts are available from Harbor Freight Tools. Use of
any other parts will void the warranty.
18. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do
the work of a larger industrial tool. There are certain applications for which this tool was designed. Do
not modify this tool and do not use this tool for a purpose for which it was not intended.
19. MAINTENANCE. For your own safety, maintenance should be performed regularly by a qualified
technician.
SpeciaL WaRninGS When USinG thiS DRiLLinG / miLLinG machine
Using this machine may create special hazards.
Take particular care to safeguard yourself and those around you.
electrical Safety. Never operate any tool if there is an electrical hazard. Never operate an electrical
tool in wet conditions. Never operate a tool with an improper electrical cord or extension cord. Never
operate an electrical tool unless you are plugged into a properly grounded outlet, which supplies 110
Volts at
60 Hz. We recommend you use a circuit which is protected by an appropriate circuit breaker.
ejected material. Use safe practices to avoid injury from ejected material. Because milling tools
and workpieces turn at high speed, there is a danger of being injured by materials that may be ejected.
Always wear ANSI-certified eye protection. Never attempt to machine any item if it is not adequately
held. Always stand to one side of the plane in which the materials are spinning, to avoid being hit if an
item is ejected. Never allow bystanders to be in the proximity of this machine while in operation.
entanglement. Use extreme caution to prevent loose materials from being caught in the machine.
Never operate this machine with loose clothing, long hair, jewelry, or other items which may become
caught in the tools or workpieces. In case of entanglement, press the OFF switch immediately.
NOTICE: No list of warnings can be all inclusive. The operator must supply common
sense, and operate this tool in a safe manner.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
featUReS anD contRoLS of the #42827 DRiLL / miLL machine
Figure 1.
1.
2.
3.
4.
5.
6.
7.
8.
Column
Head Collar
Head Collar Lock Bolt
Head Crank
Lock Nut
Oil Drain Plug
Table Feed Wheel
Travel Stop
Knob
Red Bush Button
Green Push Button
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Leaf Screw
Cross Table Feed Wheel
Positive Depth Stop Gauge
Spindle Micro Feed Handle
Spindle Feed Handle
Speed Lever
Air Flow Plug
Oil Filler Plug
Head Body
Arbor Bolt Cover
Scale
9.
10.
11.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
UnpackinG anD inStaLLation
1.
2.
Remove protective crating and skids carefully. In the event of damage in transit, contact Harbor
Freight Tools immediately.
Read the owner’s manual and become familiar with the parts and controls on the drawings before
using this machine, as familiarity with the controls will enhance your ability and safety in using it.
inStaLLation
1.
2.
It is important that the machine be located on a hard, solid, level floor. Find a location that
supplies easy access to 110 Volt electrical service. Make sure this machine is located in a well
lighted and well ventilated area. The floor should be resistant to vibration.
Before moving the machine, be sure the head is fixed on the column. Before moving the
machine, lower the head as much as possible to lower the center of gravity. When moving the
machine be careful to keep it balanced, and not allow it to topple over.
3.
4.
5.
To set the machine on a solid concrete foundation, it’s advisable to apply a little grout to touch up
any unevenness in the concrete in order to get a solid foundation at all points.
When setting machine on a floor that has any surface irregularities, shims should be used to
correct this condition to the greatest extent possible.
There are 4 holes in the base for mounting the machine permanently to a smooth, solid, and level floor.
cLeaninG anD LUBRication
1.
Thoroughly clean the machine with a commercial degreaser.
Do not use gasoline, kerosene or other flammable liquids.
Avoid getting solvent on rubber parts, or into the electrical
controls or motor.
2.
3.
4.
After cleaning, coat all bright metal with a light lubricant to
prevent corrosion.
Lubricate all points indicated in Figure 2 with a 10 weight
machine oil.
Remove the oil filler plug and fill the reservoir with heavy
motor oil, until the oil level reaches the middle of the oil
fluid level indicator. Replace the plug.
LeveLinG thiS machine
1.
Before operation, it is critical to level the work surface both
lengthwise and crosswise, using a precision level. It will not
be possible to maintain accuracy of machined parts if the
mill is not properly leveled to start.
Figure 2. Lubrication Points.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
BaSic opeRation
Prior to Operation
1. Check the oil level, and if necessary fill to the mid point of the oil level window.
Basic Controls
Please refer to Figure 1 on page 5.
1.
2.
Raise and lower the Head by using the Head Crank (#4).
Feed the Spindle using Spindle Feed Handle (#16). Precise movements may be made using the
Spindle Micro Feed Handle (#15).
3.
4.
Move or feed the table from side to side by using the Table Feed Wheel (#7).
Move the Table front to back using the Cross Table Feed Wheel (#13).
Adjusting the Head
1.
To raise or lower the head, loosen the 2 heavy
duty head lock nuts shown in the left part of
Figure 3. Use the left side head handle to
raise or lower the head on its rack and pinion
mechanism.
2.
The head may be rotated 360O by loosening
the same bolts mentioned in item 1. Adjust
the head to the desired angle, then fix the
heavy-duty head lock nuts. Periodically check
the tightness of these nuts, especially during
prolonged use of the machine.
Figure 3. Adjusting the Head
3.
To set the head at an angle, loosen the three
nuts shown in the right part of Figure 3.
Retighten the nuts when you have set the angle at the desired degree. Refer to the scale on the
right side of the head to read the angle.
Preparing for Drilling
Please see Figure 4.
1.
Rotate the knob in the center of the spindle
feed handle (#16) counterclockwise to
loosen the spindle for vertical travel.
You can move the spindle vertically by
operating the spindle feed handle.
For more precise movement of the spindle,
operate the micro feed handle (#15).
For drilling blind holes (which do not pass
through the workpiece), set the positive
depth stop gauge (#14). To do so, first
determine the desired depth. Then adjust the
positive stop gauge so that the distance from
the tip of the drilling bit to the end of the
gauge is equal to the desired depth.
2.
3.
4.
Figure 4. Settings for Drilling
5.
For drilling holes that pass through the workpiece, set the stop gauge in its uppermost position.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for Milling
1.
2.
Adjust the positive stop gauge to its uppermost position.
Using the spindle feed handle, adjust the bit to approximately the correct height. Tighten the
knob in the center of the spindle feed handle (#16).
3.
4.
Set the final vertical adjustment using the micro feed handle.
Lock the rack sleeve at this height with the fixed bolt.
Preparing for Tapping
1.
2.
Adjust the positive depth gauge to the required position.
Loosen the knob in the center of the spindle feed handle.
Adjusting Table Slack and Compensating for Wear
1.
2.
3.
Your machine is equipped with gib strip adjustment
to compensate for wear and excess slack on cross and
longitudinal travel.
Rotate the gib strip bolt slightly counterclockwise to
tighten the gib strip. Rotate it slightly clockwise to loosen
the gib strip.
Adjust the gib strip bolt until very slight drag is felt when
moving the table.
Locking the Table Base and Machine Base
1.
When milling using the longitudinal feed, it is a good idea
to lock the cross feed table to ensure the accuracy of your
work. To do this, tighten the small leaf screw located on
the right side of the table base.
2.
3.
When milling using the cross feed, lock the longitudinal
travel. Do this by tightening the two small leaf screws on
the front of the table base.
Adjustable travel stops are mounted on the front of the
table to limit cross travel, and therefore milling length.
Changing Machine Speed
1.
Turn the power off.
Figure 5. Adjusting the Gib Strips.
Levers
RPM @ 60Hz
L-1
95
L-2
175
L-3
310
H-1 H-2 H-3
450 850 1500
Figure 6. Machine Speed Lever Settings.
2.
3.
To select the proper speed, move the speed lever to the desired position. See Figure 6.
If the lever does not move smoothly and completely, remove the arbor bolt cover (#21). Rotate
the spindle slightly to engage the gears, then replace the arbor bolt cover.
4.
Recheck the lever setting, and then turn the power on.
reV 09b
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing and Changing Tools
WaRninG: turn off the power and unplug the machine before installing or changing tool bits.
Removing Face Mill or Drill Chuck Arbor
1.
2.
3.
4.
Remove the arbor bolt cover (#21) on the top of the head body (#20).
Loosen the arbor bolt at the top of the spindle shaft approximately 2 turns with a suitable wrench.
Rap the top of the arbor bolt with a mallet.
After the taper has broken loose, hold the chuck arbor with one hand, and detach the arbor bolt
with the other hand.
5.
Replace the arbor bolt cover.
Installing a Face Mill or Cutter Arbor
1.
2.
3.
4.
Remove the arbor bolt cover (#21) on the top of the head body (#20).
Insert the cutter and cutter arbor into the taper of the spindle.
Tighten the arbor bolt securely, but do not overtighten.
Replace the arbor bolt cover.
Additional Tools and Accessories You Will Find Helpful
Your Drill Mill machine is equipped with an R-8 spindle taper. Many tools, bits, and accessories
are available for this standard.
1.
2.
3.
4.
5.
6.
7.
8.
Taper Drills
Reamers
End Mills
Cutter Arbors
Taps
Collets
Adapters and Sleeves.
Table Power Feed
reV 01f
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Rules for Drilling and Milling
1.
2.
3.
4.
Be sure the drill bit or cutting tool is securely locked in the chuck.
Be sure the chuck key is removed from the chuck before turning on the power.
Adjust the table or depth stop to avoid drilling into the table.
Shut off the power, remove the drill bit or cutting tool, and clean the table before leaving the
machine.
5.
Always use clamps or a vise to hold the workpiece, to prevent it from moving, rotation or flying
off while being machined.
6.
Never wear gloves when machining, as they can become
entangled in the bit, causing injury.
Specification of the T-Slot.
Please refer to Figure 7. Purchase or make T-bolts and other
table top fixtures to fit these dimensions.
NOTE: These dimensions are in millimeters
Figure 7. T-Slot Dimensions.
tRoUBLeShootinG
The machine doesn’t run when the power switch is turned ON.
1.
2.
3.
The knob (#9) is in the STOP position.
A fuse has burned out. Check in the switch box, and replace if necessary.
If there is a surge in the current, the circuit breaker may have opened. Press the circuit breaker
back in, if it is in the open position.
4.
5.
The gears may not be engaged. Adjust the speed lever to be sure it is engaged.
A capacitor may have failed. Check the capacitance and replace if necessary.
The motor overheats, or there is insufficient power.
1.
2.
The machine is overloaded. Reduce the feed rate, and/or increase the spindle speed.
The voltage supply is too low. If you have an unreliable power supply, check with a qualified
electrician to repair it.
3.
4.
5.
6.
The magnetic switch may have a burned or broken contact point. Replace the switch.
The contactor relay may be broken. Replace it.
The motor carbon brushes may be worn or cracked. Check them and replace if needed.
There may be a poor electrical connection. Have a qualified electrician check the wiring and
power supply.
7.
8.
The motor may be burned out. After a long period of heavy use, the motor may burn out. If so,
replace the motor.
The drill bit or cutting blade may be worn. Sharpen or replace the bits as needed.
reV 09b
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
The spindle bearing is very hot.
1.
There is insufficient lubrication. Turn off the power, and check the bearing for lubrication. If
necessary, apply a medium weight bearing grease.
2.
The spindle bearing is worn, or is fixed too tight. Turn off the power, unplug the electrical
connection, and rotate the spindle by hand. It must turn freely. If not, check the bearing
adjustment. If you feel unevenness in the bearing, you will have to replace it.
The spindle has been turning at high speed for a long time. After long use, turn the machine off
for a while to give it a rest, and allow it to cool off.
3.
The Table Travel is not Balanced
1.
2.
3.
The spindle taper gap is too wide. Adjust the arbor bolt properly.
One of the leaf bolts may be loose. Check and tighten them if necessary.
The feed is too deep. Reduce the depth of the cut, and make several passes to reach the required
depth.
4.
The gib strip may be out of adjustment. Check it and adjust it if necessary.
There is a vibration, and the cut is not smooth
1.
The spindle bearing may be improperly adjusted or is worn. Check it and adjust or replace as
necessary.
2.
The spindle is loose up and down. Check the adjustment of the two inner bearing covers. Adjust
them so there is no free play in the taper bearing, and the bearing turns freely. Tighten them
against each other to save this adjustment.
3.
4.
5.
6.
The gap of the taper sliding plate is too wide. Adjust the bolt tension.
The chuck is loose. Tighten the chuck.
The drill bit or cutter is dull. Sharpen or replace it. Use cutting fluid to preserve tool life.
The workpiece is not held firmly. Check the clamps or vise you are using, and assure that the
workpiece cannot move.
The micro feed does not work smoothly
1.
2.
3.
The clutch may be loose. Check this and tighten if necessary.
The worm or worm shaft may be worn. Check these and replace if necessary.
The handwheel fixed screw may be loose. Check it and tighten if necessary.
The workpiece is not machined accurately
1.
A heavy workpiece may be out of balance. Check to see that heavy workpieces are held in
balance.
Out of balance pieces may shift when being machined.
A hammer has been used on the workpiece. Never strike the workpiece with a hammer.
The table may not be level. Check the table with a spirit level to be sure it is level both side to
side and front to back.
2.
3.
4.
The machine may not be stable in the floor. Check to be sure the machine is firmly mounted to
the floor.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
eLectRicaL WiRinG
NOTE: This machine is designed to operate on 110 Volt/60 Hz Single Phase power supply only.
This machine is supplied with a 3-prong grounded plug. Use only a power supply which is
grounded, and which is protected by an appropriate circuit breaker. Check with a qualified
electrician before using this machine.
Serious injury or damage to property can result from improper electrical connection.
notice: 110 volt systems deliver highly energetic currents which are
capable of causing lethal injury.
Do not operate this machine without first obtaining professional installation
and safety inspection to prevent operator injury.
iaGRam
WiRinG DiaGRam keY
1
X
-
X
-
X
X
0
-
-
-
-
-
-
2
-
L1-V1
L1-Z2
L2-Z2
L2-V1
L1-U1
L2-U2
X
-
X
X
X
Figure 8. Wiring Diagram.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
maintenance
After each use:
1.
2.
3.
4.
5.
Turn off the power switch and unplug the machine from its power source.
Remove any tool bits, clean and lubricate them, and return them to their storage case.
Using a stiff bristle brush, brush off all chips and shavings left from the machining operation.
Using a rag, wipe off any excess or dirty oil or cutting fluid left on the machine.
Lubricate the points indicated in Figure 2. Apply light grease or oil to all unpainted metal to
prevent corrosion.
6.
Cover the machine to prevent dust or dirt contamination when not in use.
Daily Maintenance:
1.
2.
3.
Fill the oil reservoir to the proper level before each use.
Check the tightness of the bolts holding the head in place.
If overheating is observed, or unusual noises are produced, stop the machine immediately to
check for lack of lubrication, faulty adjustments, dull tool bits, or other deficiencies. Correct any
problems before resuming work.
4.
Keep the work area clean. If chips or shavings accumulate on the table or fixtures, shut off
the power and clean the chips away with a stiff bristle brush. Re-check the lubrication before
continuing.
Weekly Maintenance:
1.
2.
Clean and coat the lead screw with oil.
Check the lubrication of the sliding parts of the table. Apply light grease if needed.
Monthly Maintenance:
1.
2.
Adjust the accuracy of the slides on both the cross and longitudinal feeds.
Lubricate the bearings, worm gear and worm shaft with light grease.
Yearly Maintenance:
1.
2.
Adjust the table to assure that it is level in all directions.
Check the electrical cord, plug, circuit breakers and related connections to assure that they are
secure and safe.
3.
Drain the lubricant from the gear box and replace it with heavy grade motor oil.
NOTE: Some parts on the following pages are listed and shown for illustration
purposes only and are not available individually as replacement parts.
pLeaSe ReaD the foLLoWinG caRefULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY: NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REP-
RESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT: IN FACT THE MANUFACTURER A ND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL RE-
PAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNI-
CIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GeaReD heaD DRiLL miLL machine, heaD paRtS LiSt
Please refer to Parts Diagrams on Page 16 and 17
part
description
Qty.
1
1
1
2
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
3
3
1
1
1
1
part
description
Qty.
2
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
3
3
3
2
1
1
2
1
1
1
4
4
2
1
2
1
1
2
6
2
1
1
1
1
1
2
1
1
1-01 Arbor Bolt Cover
1-46 Ball Bearing (202G)
1-47 Worm Shaft
1-48 Key
1-02 Arbor Bolt
1-04 C-Retainer Ring
1-05 Ball Bearing (80108)
1-06 Spindle Sleeve Cover
1-07 Oil Seal
1-49 Gear
1-50 Oil Seal
1-51 Ball Bearing (80107)
1-52 Head Body Fix Bolt
1-53 Oil Drain Plug
1-54 Graduated Rod
1-56 Switch Box
1-57 Main Cable
1-58 Head Handle
1-59 Worm Shaft
1-60 Worm
1-08 Seal Retainer
1-09 Cap
1-10 C-Retainer Ring
1-11 Head Body
1-12 Rubber Flange
1-13 Feed Base
1-14 Lock Nuts
1-15 Taper Roller Bearing (7206E)
1-16 Rack Sleeve
1-17 Spindle Shaft
1-18 Taper Roller Bearing (7207E)
1-19 Bearing Cap
1-20 Gear Shaft
1-21 Gear
1-61 Shaft
1-62 Handwheel
1-63 Nuts
1-64 Spring Washer
1-65 Bolt
1-66 Lever Bracket
1-67 Lever (Left)
1-68 Lever (Right)
1-69 Screw
1-22 Grip
1-23 Ring
1-24 Handle Rod
1-25 Fixed Tight Collar
1-26 Fixed Tight Collar (thread)
1-27 Screw Key
1-28 Oil Seal
1-70 Lever Shaft (Right)
1-71 Lever Shaft (Left)
1-72 Name Plate
1-73 Screw
1-29 Gear
1-74 Screw
1-30 Spring and Ball
1-31 Gear Shaft
1-32 Key
1-75 Speed Lever
1-76 Degree-Meter
1-77 Rivet
1-33 Ring
1-79 Head Collar
1-80 Motor Cable
1-81 Oil Filler Plug
1-82 Bolt
1-34 Gear
1-35 Bearing Spacer
1-36 Sleeve
1-37 Gear
1-83 Pin
1-38 Key
1-84 Head Body Cover
1-85 Screw with Plumb Knob
1-86 Motor
1-39 Handle Rod
1-40 Knob
1-41 Ball Bearing (80202)
1-42 Inner Ring
1-87 Fluid Level Indicator
1-89 Airflow Plug
1-90 C-Ring
1-43 Shaft
1-44 Micro Adjusting Indicator
1-45 Worm Cover
1-91 Set Distance Nut
1-92 Set Position Block
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
DRiLL miLL machine, paRtS LiSt
Please refer to Parts Diagrams on Page 16 and 17
part
1-93 Lock Nut
description
Qty.
1
1
1
2
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
2
3
1
2
1
2
2
1
2
4
1
1
1
1
1
1
1
1
1
3
2
part
description
Qty.
4
2-03 Thrust Bearing (8103)
2-04 Square Flange
2-05 Table Screw
2-06 Base
1-94 Support Base
1-95 Handle
1
1
1-96 Oil Seal
1
1-101 Head Raise Bracket
1-102 Limit Plate
2-07 Gib Strip
1
2-08 Column Base
2-09 Column Base Ring
2-10 Rack
1
1-103 Spring Cover
1-104 Spring
1
1
1-105 Spring Base
1-106 Pinion Shaft
1-107 Worm Gear
1-108 Feed Cover
1-110 Spring Base
1-111 Lock Bolt with Knob
1-115 Spring
2-11 Column Head
2-12 Gib Strip Bolt
2-13 Leaf Screw
1
2
2
2-13-2 Knob
2
2-14 Moveable Fixed Bock
2-15 Table Base Nut
2-16 Center Base
2-17 Antidust Plate
2-18 Antidust Plate
2-19 Antidust Plate
2-20 Table Clutch
2-22 Left Flange
2
1
1
1-134 Hex Head Bolt
1-135 Hex Nut
1
1
1-136 Spring Pin
1
1-137 Lock Washer
1-139 Phillips recessed round head screw
1-140 Travel Switch
1-141 Hex Nut
1
1
2-23 Table Nut
1
2-24 Table Screw
2-26 Right Flange
2-27 Gib Strip
1
1-142 Key
1
1-143 Hex Socket Head Screw
1-145 Hex Set Screw
1-146 Hex Set Screw
1-147 Hex Set Screw
1-148 C-Retainer Ring
1-150 Locknut
1
2-28 Table
1
2-29 Fixed Block
2-30 Moveable Fixed Ring
2-37 Base Screw Collar
2-121 Meter Indicator
2-131 Hex Head Bolt
2-143 Hex Set Screw
2-145 Hexagon
2
2
1
4
1-151 Washer
4
1-153 Hex Set Screw
1-154 C-Retainer Ring
1-155 Hex Set Screw
1-156 Rod
10
1
2-166 Spring Pin
3
2-167 Indicated Zero with Screw
2-168 Oil Ball
2
1-157 Retainer
5
1-158 Knob
2-169 Hex Head Bolt
2-170 Washer
4
1-184 Screw
4
1-185 Washer
2-171 Hex Set Screw
2-172 Hex Head Bolt
2-173 Spring Washer
2-174 Hex Set Screw
2-175 Hex Set Screw
2-176 Hex Set Screw
10
4
1-187 Washer
1-188 Phillips Head Recessed Screw
1-189 Travel Switch Base A
1-190 Travel Switch Base B
2-01 Table Handle with Wheel
2-02 Dial Clutch
4
2
1
2
reV 09b
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
veRticaL miLLinG machine, heaD paRtS DiaGRam
Please refer to Parts List on Pages 14 and 15.
NOTE: When ordering parts from this diagram, use prefix “1”. (example: P/N 1-01 Arbor Bolt Cover)
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
veRticaL miLLinG machine, BaSe paRtS DiaGRam
Please refer to Parts List on Page 15.
NOTE: When ordering parts from this diagram, use prefix “2”.
(example: P/N 2-01 Table Handle with Wheel)
SKU 42827
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
|