OUTDOOR IMITATION CAMERA
Model 95153
SET Up INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANUAl.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 07b, 08a, 09k
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this product. Approved accessories are available from Harbor Freight Tools.
10.
Do not install the Imitation Camera if under the influence of alcohol or drugs.
Read warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not install the unit.
11.
12.
For your safety, service and maintenance should be performed regularly by a
qualified technician.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE ThESE INSTRUCTIONS.
UNpACKINg
When unpacking, check to make sure that the product is intact and undamaged. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
SKU 95153
For technical questions, please call 1-800-444-3353
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbly
Pivoting Screw
Camera
Stand (2)
Wall Bracket (1)
FIgURE 1
1.
Twist the Camera Stand (2) into the Wall Bracket (1). Tilt-up the Pivoting Screw.
See Figure 1.
Camera
Housing (3)
Pivoting Screw
Wires (4)
Camera
Stand (2)
FIgURE 2
2.
3.
Screw the Pivoting Screw into the housing of the Camera. Be sure it is secure.
See Figure 2.
To make the Camera look more authentic, tuck the Wires (4) into the holes in the
Camera Stand (2). See Figure 2.
Note: Turn pivot screw 90° if wall bracket is mounted on a vertical surface.
SKU 95153
For technical questions, please call 1-800-444-3353
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
bATTERy INSTAllATION
Warning: Only install batteries of the same type and charge level. Replace both
batteries at once. Install batteries according to polarity markings.
Sun-Visor (6)
Battery Case (11)
Batteries (9)
Rear Housing (7)
Battery Cover (8) and Battery Cover Screws (5)
FIgURE 3
1.
Remove the two Battery Cover Screws (5) from the Battery Cover (8) with a screwdriver
(sold separately). See Figure 3.
2.
3.
Slide the Battery Cover (8) off the Battery Case (11).
The Battery Case (11) is inside the Rear Housing (7).
CAUTION: The housing and other machined parts of this item may have sharp
burrs that can cut you. Use care when changing the batteries.
Carefully remove the Batteries (9) from the Battery Case (11).
4.
5.
If present, remove old batteries and dispose of or recycle them properly.
Carefully place two new “AA” Batteries (9) into the Battery Case (11). Be sure that the
polarities (+ or -) of the batteries line up with the polarity signs.
6.
7.
Carefully replace the Battery Cover (8). Insert the Battery Cover Screws (5) and tighten
them with the screwdriver.
Check LED light. If it does not light, repeat the steps or replace the batteries with new
ones.
SKU 95153
For technical questions, please call 1-800-444-3353
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTAllATION
1.
Chose a wall or ceiling location that allows you to mount the unit onto a solid surface
capable of sustaining the weight of the unit. If you cannot mount to wall studs, you
will need to use the Dry Wall Mounting Anchors and Wood Screws (10). Be aware, the
Camera needs to be mounted securely so it will not fall off the mounting and cause
personal injury or property damage.
Note: The mounting holes on the Outdoor Camera are approximately 1/4” or 6 mm.
Mounting Holes
Wall Bracket (1)
FIgURE 4
2.
3.
Hold the Wall Bracket (1) of the assembly against the surface you wish to mount. Using
a pencil (not included), draw dots of the mounting holes. See Figure 4.
Warning: Check that there are no hidden wires, cables or other obstructions in the
mounting location. Predrill the holes.
4.
5.
Install the drywall anchors into the holes if mounting into drywall.
Line up the holes in the mounting bracket with the holes in the wall and hold the unit
in place. Mount using the Wood Screws (10).
MAINTENANCE
Keep the Imitation camera clean and free of spider webs.
SKU 95153
For technical questions, please call 1-800-444-3353
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pARTS lIST
pART #
DESCRIpTION
QTy.
1
2
Wall Bracket
1
Camera Stand
Camera Housing
Coaxial Wire
1
3
1
4
1
5
Battery Cover Screw (not shown)
Sun-Visor
2
6
1
7
Rear Housing
1
1
8
Battery Cover (not shown)
“AA” Battery (not included)
Drywall Anchor and Wood Screw
Battery Case (not shown)
9
2
10
11
3 ea.
1
pARTS DESCRIpTION
6
5
3
8
pivoting Screw
11
7
Adjustable
Screw
2
4
1
10
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
plEASE READ ThE FOllOWINg CAREFUlly
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 95153
For technical questions, please call 1-800-444-3353
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
|