Slim & Light
Floor
Sanitizer
Si-35
The Fastest, Easiest
and Most Effective Way
to Clean and Sanitize
Your Floor!
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
You’ll never use a bucket and mop to clean your floors again!
Congratulations on purchasing the HAAN Slim &
Light Floor Sanitizer. Now you have an easy way to
clean your tile, hardwood, laminate, linoleum and
vinyl floors.
Your floor sanitizer uses steam to remove tough
grease, dirt and grime. Steam is nature’s purest and
most powerful cleaner for safely cleaning all hard
surfaces in your home without harsh chemicals, for
a perfectly ecological approach. No film, no residue
– just clean, germ-free floors.
The HAAN Slim & Light Floor Sanitizer is so easy
to assemble, you can put it to use right away –
anywhere you want to clean and sanitize – from your
kitchen and living room to your bathroom floors.
Look for the HAAN “steamlet” symbol in this manual
for Helpful HAAN Hints that will help you make the
most of your new HAAN Slim & Light Floor Sanitizer.
Backed with a one-year limited warranty, your quality
HAAN Slim & Light Floor Sanitizer is sure to give
you years of dependability. And our Customer Care
representatives are available to answer any of your
questions about your new floor sanitizer.
Thousands of HAAN customers have already fallen
in love with the HAAN Slim & Light Floor Sanitizer.
We’re confident you will, too.
Thank you again for purchasing the HAAN Slim &
Light Floor Sanitizer.
The HAAN Team
877-HAAN DIRECT / 877-422-6347
pg 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
For HoUSeHolD USe onlY
Basic precautions should be observed when using an
electrical appliance, including the following:
iMPortant
1. Do not direct steam at people, animals, or at electrical
outlets.
i
Be sure to read ALL
instructions and warnings
before using your HAAN
Floor Sanitizer.
2. Do not expose to rain.
3. Store indoors.
4. Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
5. Do not leave steam cleaner unattended.
Warning
6. Do not leave the steam cleaner connected to an
electrical outlet when not in use.
Risk of electrical shock -
be sure to read and follow
all instructions and
warnings.
7. Do not service steam cleaner when it is plugged in.
8. Do not use with damaged cord or plug.
9. Do not use steam cleaner if it has been dropped,
damaged, left outdoors or dropped into water. Return
to a service center.
CaUtion
!
10. Do not handle steam cleaner with wet hands.
The SI-35 emits steam at
212˚F to sanitize the area
of use. This means that the
steam head, Ultra-Microfiber
Pads and Gliding Attachment
get very hot during use.
Care should be taken when
using this appliance and
DO NOT touch them during
use except in the approved
manner as outlined in this
manual.
11. Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp corners or
expose cord to heated surfaces.
12. Do not unplug by pulling on cord.
13. Do not use appliance in an enclosed space filled with
vapor given off by oil-base paint thinner, some
moth-proofing substances, flammable dust, or other
explosive or toxic vapors.
14. Do not allow to be used as a toy.
15. Do not use on leather, wax polished furniture or
floors, synthetic fabrics, velvet or other delicate,
steam-sensitive materials.
SAVE THESE
INSTRUCTIONS -
For household use only.
Any other use of this
appliance will void the
manufacturer’s warranty.
16. Do not immerse.
17. Do not use for any purpose other than described in
this User Manual.
18. Use only manufacturer’s recommended attachments
– use of attachments not provided or sold by HAAN
pg 2
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
may cause fire, electric shock or injury.
19. Never put descaling, aromatic, alcoholic or detergent
products into the steam cleaner, as this may damage
it or make it unsafe for use.
20. Unplug by grasping the plug, not the cord.
21. Close attention is necessary when used by or
near children.
22. If the circuit breaker activates while using the steam
function, discontinue product use immediately and
contact the customer support center. (Beware of the
risk of electrical shock.)
23. Do not allow the product to be disassembled and/
or modified by anyone other than an authorized
service technician. (Doing so can result in fire and/
or electrical shock.)
grounding instructions:
iMPortant
The HAAN SI-35 must be connected to a grounded (3-prong)
wiring system. Grounding provides a safe path of least
resistance for electrical current, in the event the unit should
malfunction or break down, thereby reducing the risk of
electrical shock. The cord for this product has an equipment-
grounding conductor and a grounding plug. Do not plug it into
an outlet that is not properly installed and grounded in
accordance with all local codes and ordinances.
Grounded
Pin
Grounded
Outlet
Warning
Check with a qualified electrician or service person if you
aren’t sure if the outlet is properly grounded. If it will not
fit the outlet, have a proper outlet installed by a qualified
electrician. This appliance is designed for use on a nominal
120-volt circuit and has a grounding attachment plug as
illustrated above. Make certain that the appliance is connected
to an outlet having the same configuration as the plug. No
plug adapter should be used with this appliance.
DO NOT modify the plug.
Improper connection of
the equipment-grounding
conductor can result in a
risk of electrical shock.
877-HAAN DIRECT / 877-422-6347
pg 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Description
1
2
Si-35
Slim & Light
Floor
Sanitizer
4
3
5
6
7
8
9
10
11
Included Accessories:
Ultra-Microfiber
Pads (2)
Gliding Tray (1)
13
Floor Protector/
12
Resting Mat (1)
pg 4
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
FeATUReS:
1. Handle -
with non-slip ergonomic grip to reduce hand & wrist stress.
2. Storage Hook -
Rotates 360˚ so it can be used to manage the cord and then
provide convenient, easy hanging storage.
HELPFUL HAAN HINT:
15 Powerful Steam Jets
are spaced perfectly to
cover more floor in less
time. Be assured you are
steam cleaning when
you push the machine
forward, as well as when
you are pulling it back.
3. Pivoting Power Cord Wrap-
releases cord with a flick of the wrist.
4. Power Cord Management System -
keeps your pathway clear
5. Power Cord with Flexible Cord Support -
double insulated cord with a 3-prong plug complete with
a flexible cord support strengthens cord connection.
6. Removable Water Tank -
goes to the sink for easy filling and allows for 20 minutes
of continuous steam on just one tank.
7. Water Tank Release Button
HELPFUL HAAN HINT:
To extend the life of your
Ultra-microfiber pads,
always place your unit on
the floor protector/resting
pad while the unit heats
up, and attach the Ultra-
Microfiber pad when the
unit is ready to use.
8. Indicator Light -
turns red when unit is ON.
9. ON/OFF Switch -
Steam Power Switch for easy ON/OFF operation.
10. Steam Head -
gets around and under difficult areas.
11. Ultra-Microfiber Pad - (2)
patented super-absorbent Ultra-Microfiber Pads lock in dirt
and leave floors dry to the touch. Specially designed for
‘No-Touch’ attachment and removal.
Make sure to check for the following accessories!
HELPFUL HAAN HINT:
While using the Floor
12. Floor Protector/Resting Mat -
for use when heating up your floor sanitizer or when
taking a break from active cleaning.
Sanitizer with the Gliding
Tray will not lift all set-in
stains from your carpet, our
patented Ultra-Microfiber
pad may be used to act as a
“blotter” for removing most
fresh, wet spills and stains.
13. Gliding Tray -
easily attaches to unit for sanitizing and refreshing
carpeted areas.
877-HAAN DIRECT / 877-422-6347
pg 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your Floor Sanitizer
1 ➟ 2 Ready to Go
To enable you to get the most satisfaction
from your Floor Sanitizer be sure to follow
the assembly and operating instructions
included in this manual. Read this manual
thoroughly before assembling your unit.
Locking
Pin
Pay specific attention to the product
description to familiarize yourself with all
the parts of your Floor Sanitzer. Locate
and organize the parts of the unit before
assembling. No additional tools are needed
to put the unit together. It is quick and easy.
1 Look for the small red
“HANDLE” arrow on the
aluminum pipe; align the
black pistol-grip handle
with the locking pin; hold
the pin down; insert the
pole and snap it into place.
Locking
Pin
Align the lower shaft
2
(where you’ll find the
white hook) with the
locking pin on the
side and snap it
into place.
Storage Hook
Rotates 360˚
pg 6
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using Your Floor Sanitizer
Be sure to read ALL instructions and warnings
before using your HAAN Floor Sanitizer.
i
Warning
!
HELPFUL HAAN HINT:
Your floor sanitizer is designed to clean hard floor surfaces
that will withstand high heat. Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that have been treated
with wax or some no-wax floors, the sheen may be removed
by the heat and steam action. It is always recommended to
test an isolated area of the surface to be cleaned before
proceeding. We also recommend that you check the use and
care instructions from the floor manufacturer.
Never leave the appliance in
one spot on any surface for
any period of time. Always
place your Floor Sanitizer on
the Floor Protector/Resting
Mat when stationary and
make sure the floor sanitizer
is turned off not in use.
CaUtion
Use a grounded receptacle. Use only a heavy duty extension
cord rated for 15 amps minimum – DO NOT use an ordinary
extension cord. To provide continued protection against the
risk of electric shock, connect to properly grounded outlet only.
HELPFUL HAAN HINT:
DO NOT add cleaning
solutions, scented perfumes,
oils or any other chemicals
to the water used in this
appliance. Use regular tap
water, or if the tap water in
your area is very hard, we
recommend you use
iMPortant
This product is NOT for space heating purposes.
iMPortant
Always be sure that your floor sanitizer is UNPLUGGED from
the wall receptacle prior to filling the water tank.
distilled/purified water.
Always empty water from
water tank after use.
CaUtion
!
The SI-35 emits steam at 212˚F to sanitize the area of use.
This means that the steam head, Ultra-Microfiber Pads
and Gliding Attachment get very hot during use. Care
should be taken when using this appliance and DO NOT
touch them during use except in the approved manner as
outlined in this manual.
877-HAAN DIRECT / 877-422-6347
pg 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Floor Sanitizer
Fig 1a
Operating Instructions:
1) Remove all parts from the packaging.
2) Assemble the unit as described on page 6.
3) Place the Floor Sanitizer on the Floor Protector/
Resting Mat and remove the water tank by
Fig 1b
Fig 2
pressing the water tank removal button. (Fig 1a)
4) Grasp the water tank, pull out and up to remove.
(Fig 1b)
5) Turn the cap on the water tank counter-clockwise
to open it and fill the tank with water. (Fig 2)
6) After filling the water tank with water, firmly
turn the cap clockwise to close. Insert the tank,
cap down, into the receptacle in the main unit
and push forward until it clicks into place. (Fig 3)
Fig 3
7) Press the STEAM ON/OFF button found on the
front of the unit. It takes approximately 30
seconds for the floor sanitizer to heat up.
8) Place an Ultra-Microfiber pad on the floor with
the ‘hook & loop’ side facing up.
9) Raise the unit off the Floor Protector/Resting Mat
and lightly press it down onto the Ultra-Microfiber
pad. You are now ready to steam clean and sanitize
your floor. (Fig 4)
Fig 4
10) Push and pull the floor sanitizer slowly across
the floor to thoroughly steam clean each section.
11) When there is no more water in the water tank,
you will hear a vibration sound from the main
unit. To refill the water tank and continue to
sanitize, turn your floor sanitizer off. Unplug the
unit from the electrical wall outlet and remove
the water tank and refill the water tank as before.
HELPFUL HAAN HINT:
Never leave the appliance in one
spot on any surface for any period
of time. Always place your Floor
Sanitizer on the Floor Protector/
Resting Mat when stationary and
make sure the floor sanitizer is
turned off not in use.
12) When you have finished using the Floor Sanitizer,
turn it ‘OFF’, place it on the Floor Protector/
Resting Mat and wait until the Floor Sanitizer
cools down for approximately five (5) minutes
pg 8
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions: (cont)
before removing the ultra-microfiber pad from the base.
NOTE: The ultra-microfiber pad gets very hot
with the steam. Allow it to cool before removal.
HELPFUL HAAN HINT:
After heating up, it is normal
to hear a vibration sound
from the water pump inside
the main unit. It will stop
when the air inside has been
pumped out. If the vibration
sound goes on for more
than 60 seconds, check to
be sure the water tank is
assembled correctly.
13) Store the unit upright in a protected dry area,
standing it on the Floor Protector/Resting Mat,
or by hanging it by the Storage Hook.
Special Notes on Using your HAAN Floor Sanitizer:
•
•
Always vacuum or sweep floor before sanitizing.
The easiest way to use the machine is to tilt the
handle to a 45˚ angle and clean slowly 2-3 yards
at a time.
HELPFUL HAAN HINT:
We recommend placing your
floor sanitizer on the Floor
Protector/Resting Pad while
the unit heats up. When the
unit is ready, lift it off of the
resting pad and simply place
the Ultra-Microfiber pad on
the floor. The ‘hook & loop’
system quickly attaches the
pad to the base of the unit.
Never push or pull the floor
sanitizer across your floor
without the Ultra-Microfiber
pad attached to the base.
•
Although we do not advocate the use of chemicals,
to remove stubborn stains from vinyl or linoleum
floors, you can pre-treat with a mild detergent
and some water before using the floor sanitizer.
Ultra-Microfiber Pads
What is an ultra-microfiber?
An ultra-microfiber is a textile fiber that is thinner
than a microfiber. The Ultra-Microfiber by HAAN
Corporation is 5-10 times thinner than common
microfiber providing for a significantly higher thread
count in the same surface area. The thinner and
higher the thread count, the greater the absorbtion.
HAAN’s Ultra-Microfibers are so thin that more dirt
and dust gets trapped between the fibers, making
your cleaning simpler and less time-consuming.
HELPFUL HAAN HINT:
Never leave the Ultra-
Microfiber pad on your
floor sanitizer when you
have finished using the
floor sanitizer.
877-HAAN DIRECT / 877-422-6347
pg 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions: (cont)
How to Use Ultra-Microfiber Pads:
Fig 5
Fig 6
Fig 7
1) Please make sure that you always use completely
dried pads.
2) The Ultra-Microfber pad is made up of multiple
layers of super absorbent material. (Fig 5) The
outer layer is Ultra-Microfiber on one side and
a ‘hook & loop’ system on the other side that
attaches easily to the underside of the steam
head. Simply place the pad on the floor with the
‘hook & loop’ side up, and lightly press the SI-35
Floor Sanitizer down on the pad.
(refer back to Fig 4)
3) As high temperature steam passes through a pad
to contact the floor to kill germs, molds and mites,
it is natural that the pad gradually absorbs moisture.
After a certain length of time, the pad repels
water and becomes damp. When the pad becomes
saturated, turn the unit ‘OFF’ and wait until the
Floor Sanitizer cools down for approximately five
(5) minutes.Put your foot on a corner of the pad
and lift the Floor Sanitizer off the pad. (Fig 6)
Replace with a dry pad on the unit, turn the unit
back on and continue.
4) To keep the floor clean and dry, replace the pad
when it is dirty and/or saturated.
Warning
!
Colors may bleed during
first wash. Be careful when
machine washing or drying
with mixed fabrics as
How to Clean and Store the HAAN
Ultra-Microfiber Pads:
1) Ultra-microfiber pads are easy to wash. Soak pads
for about 1-2 hours in cold or lukewarm water
with laundry detergent and hand wash them.You
can also drop the pads in a washing machine and
clean them using the gentle/delicate cycle. DO
NOT use fabric softener as this will compromise
the absorbancy of the microfiber. (Fig 7)
micro-fiber cloths will pick
up lint from other fabrics.
HELPFUL HAAN HINT:
You may dry your Ultra-
Microfiber pads in a machine
dryer on a low setting, but for
longer life, we recommend air
drying the pads.
2) It is best to let the pads air dry but you can
place them in the dryer using low heat.
pg10
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions: (cont)
glide attachment
What is the Glide Attachment?
The Glide Attachment enables the Floor Sanitizer to
freshen, deodorize and sanitize carpeting, rugs,
upholstery, pet cushions and more. Used with the
Floor Sanitizer it kills dust mites and other allergans
in a variety of soft surfaces.
Fig 8
Fig 9
Fig 10
How to use the Glide Attachment:
1) The Glide Attachment is used without the Ultra-
Microfiber pad. It attaches directly to the unit by
snapping onto the bottom of the steam head.
Place the front of the steam head under the tabs
on the front of the Glide Attachment and press
down. The tray is made to fit snuggly and will
snap easily into place. (Fig 8)
2) After attaching the tray, press the ‘STEAM ON/
OFF’ button found on the front of the unit. It
takes approximately 30 seconds for the Floor
Sanitizer to heat up.
3) Push and pull the Floor Sanitizer slowly across
the carpet (or other soft surface) to thoroughly
steam clean each section. (Fig 9)
4) When there is no more water in the water tank,
you will hear a vibration sound from the main
unit. To refill the water tank and continue to
sanitize, turn your floor sanitizer off. Unplug the
unit from the electrical wall outlet and remove
the water tank and refill the water tank as before.
5) When you have finished using the Floor Sanitizer,
turn it ‘OFF’, place it on the Floor Protector/
Resting Mat and wait until the Floor Sanitizer
cools down for approximately five (5) minutes.
Remove the Glide Attachment by using your foot
to snap the attachment off the steam head. The
attachment is designed for this ‘No Touch’
method of removal. (Fig 10)
HELPFUL HAAN HINT:
Never leave the appliance in
one spot on any surface for
any period of time. Always
place your Floor Sanitizer on
the Floor Protector/Resting
Mat when stationary and
make sure the floor sanitizer
is turned off not in use.
6) Store the unit upright in a protected dry area,
standing it on the Floor Protector/Resting Mat,
or by hanging it by the Storage Hook.
877-HAAN DIRECT / 877-422-6347
pg 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions: (cont)
CaUtion
How to use the Glide Attachment for Fresh Stains:
!
The SI-35 emits steam at
212˚F to sanitize the area
of use. This means that the
steam head, Ultra-Microfiber
Pads and Gliding Attachment
get very hot during use.
Care should be taken when
using this appliance and
DO NOT touch them during
use except in the approved
manner as outlined in this
manual.
The Glide Attachment can be used to break up fresh
stains on carpeting, rugs, upholstery, pet cushions
and other soft surfaces. Follow the instructions below.
1) With the Glide Attachent on the Floor Sanitizer,
press the ‘STEAM ON/OFF’ button. It takes
approximately 30 seconds for the Floor Sanitizer
to heat up.
2) Place the Floor Sanitizer over the stain and hold it
in place for a few seconds to allow the steam to
penetrate the area of the stain.
3) Push and pull the floor sanitizer slowly across
the area to work the steam into the stain.
Fig 11
4) Carefully remove the Glide Attachment by using
your foot to snap the attachment off the steam
head. The attachment is designed for this easy
‘No Touch’ method of removal. (Fig 11)
5) Place a dry Ultra-Microfiber Pad ‘hook & loop’
side up and press the unit onto the pad. Use the
pad to rub the area, simultanously working at the
stain and blotting the moisture from the surface.
6) When you have finished using the unit, turn it ‘OFF’,
place it on the Floor Protector/Resting Mat and
wait until the Floor Sanitizer cools down for
approximately five (5) minutes before removing
the Ultra-Microfiber Pad from the base.
HELPFUL HAAN HINT:
While using the Floor
Sanitizer with the Gliding Tray
will not lift all set-in stains
from your carpet, our patented
Ultra-Microfiber pad may be
used to act as a “blotter” for
removing most fresh, wet
spills and stains.
7) Store the SI-35 upright in a protected dry area,
standing it on the Floor Protector/Resting Mat,
or by hanging it by the Storage Hook.
pg 12
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
Care & Maintenance
1) Turn your Floor Sanitizer off and unplug the unit
from the electrical outlet.
iMPortant
2) Place the unit on the Floor Protector/Resting Mat.
Always be sure that your floor
sanitizer is UNPLUGGED from
the wall receptacle prior to
cleaning or before emptying
the water tank.
3) Prepare to store the Floor Sanitizer by looping the
power cord around the pivoting cord wraps found
on the handle pole and snap the plug securely
onto the cord when complete.
4) Let your Floor Sanitizer cool for five (5) minutes
before removing the Ultra-Microfiber pad.
5) Always empty the water tank once you have
finished using your Floor Sanitizer.
HELPFUL HAAN HINT:
Never leave the appliance in
one spot on any surface for any
period of time. Always place
your Floor Sanitizer on the Floor
Protector/Resting Mat when
stationary and make sure the
floor sanitizer is turned off not
in use.
6) Remove the Ultra-Microfiber pad and wash in
warm water with a mild detergent. Never use
bleach or fabric softener when cleaning the Ultra-
Microfiber pad. The Ultra-microfiber pad can be
washed in a washing machine set on the gentle
cycle. We recommend that you air dry the pads
for 24 hours, but they can also be dried in a
clothes dryer on a low heat setting.
7) To clean the body of your Floor Sanitizer wipe it
down with a damp cloth.
CaUtion
8) Store the unit upright in a protected dry area,
standing it on the Floor Protector/Resting Mat,
or by hanging it by the Storage Hook.
Do not immerse your Floor
Sanitizer in water or any
other liquid.
HELPFUL HAAN HINT:
DO NOT use fabric softener
when washing the Ultra-
Microfiber Pads as this will
compromise the absorbancy
of the microfiber.
877-HAAN DIRECT / 877-422-6347
pg 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting and Questions
This chapter summarizes the most common problems you
could encounter with your floor sanitizer. Please read the
different sections for more details. If you are unable to
solve the problem, please contact our Customer Care
Representatives at 877-HAAN DIRECT (877-422-6347)
PROBLEM: Floor Sanitizer vibration sound last longer
than 60 seconds.
Possible Cause:
1) No water in the water tank.
2) Water tank is not snapped into place.
Possible Solution:
1) Add water to the water tank following
instruction on page 8.
2) Insert the water tank properly into the
main body of the SI-35.
PROBLEM: Floor Sanitizer does not operate.
Possible Cause:
1) Power cord not firmly plugged into outlet.
2) No power in wall outlet.
Possible Solution:
1) Check plug in outlet and set plug firmly.
2) Check fuse or breaker. Replace fuse and/or
reset breaker.
PROBLEM: Floor Sanitizer does not emit steam.
Possible Cause:
1) No water in water tank.
Possible Solution:
1) Add water to the water tank following the
instructions on page 8.
pg 14
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: Floor Sanitizer leaves water on the floor.
Possible Cause:
1) Ultra-Microfiber cleaning cloth is too wet.
2) Unit is not level on the floor..
HELPFUL HAAN HINT:
For optimal performance,
the Ultra-Microfiber pad
should be changed after
10 minutes of use.
Possible Solution:
1) Turn off unit, unplug from power outlet
and change the Ultra-Microfiber pad.
2) Always keep the floor sanitizer level and
parallel to the floor.
PROBLEM: Floor Sanitizer left a white spot on the floor.
Possible Cause:
1) Floor sanitizer left in one spot too long.
2) Floor sanitizer not rested on floor
protector pad.
3) Hard water.
Possible Solution:
1) Always place the floor sanitizer on the floor
protector pad when not in use.
2) Use distilled water.
NOTE: To remove spot, use a damp, dry cloth
with a few drops of white vinegar and rub the
stain to remove spot.
QUEStiOn: Can the HAAn floor sanitizer be used on
laminate flooring?
?
The HAAN floor sanitizer was designed for use on sensitive
flooring like laminates. We’ve spent years optimizing the
steam emission so that at nearly half the wattage of competitive
products (ours is only 800w versus most that are 1500w),
we still emit steam at 212˚F. This means our finer vapor-like
steam is gentler than those that simply blast 1500w of water
and steam onto your floor. Yet, the HANN is more effective
at penetrating stains and killing harmful germs and bacteria
than competitors. Steam is all we do, and we’ve spent years
perfecting it.
877-HAAN DIRECT / 877-422-6347
pg 15
Download from Www.Somanuals.com. All Manuals Search And Download.
QUEStiOn: the HAAn Floor Sanitizer is leaving my floor
wet. Why and what can i do about it?
?
?
The Ultra-Microfiber pad may need to be changed. For
optimal performance, the pad should be changed after 10
minutes of use.
QUEStiOn: How long can you use an Ultra-Microfiber
Pad before it needs to be changed?
The pad should be changed every 10 minutes, or when it
becomes saturated with water. The machine will become
harder to push smoothly on the floor when the pad is
saturated.
QUEStiOn: How long does a tank of water last?
?
?
A full tank will last approximately 20-25 minutes.
QUEStiOn: Sometimes my floor sanitizer becomes hard
to push – why?
If the unit is hard to push it is likely because the Ultra-
Microfiber Pad is too wet or the angle at which you are using
the machine is too high. The lower the handle, the easier the
floor sanitizer is to push across the floor.
QUEStiOn: Do i have to use distilled water in my HAAn
floor sanitizer?
?
We recommend distilled water, but you may use tap water,
unless you have hard water in your area. Using hard water
will shorten the life of your appliance.
pg 16
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
QUEStiOn: How do you use the Glide Attachment for my
carpet?
?
?
The carpet tray is to be used without the microfiber pad and
can be attached directly to the unit.
QUEStiOn: How long can i prolong the life of my HAAn?
To maintain the life of your floor sanitizer, we recommend
using HAAN’s Tank Rejuvenator (available on our web site)
every six months.
?
?
QUEStiOn: Does the HAAn work on pet stains?
Yes, the HAAN is able to spot clean fresh pet stains by
loosening and lifting the stain.
QUEStiOn: Will the HAAn floor sanitizer clean grout?
Yes, but it needs a little help. If you glide your HAAN over
the problem grout areas and then scrub with your microfiber
pad, it should effectively clean your grout.
877-HAAN DIRECT / 877-422-6347
pg 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
One-Year Limited Warranty
Your HAAN Floor Sanitizer is warranted to be free from
defects in material and workmanship for a period of one
(1) year from the date of purchase when utilized for normal
household use by the original purchaser only. The included
Warranty Registration Card must be filled out and returned
within 10 days of purchase. This is essential for your warranty
to be effective should any problem arise with this product.
Should any defect covered by the terms of the limited warranty
be discovered within one year, HAAN Corporation will
repair or replace the defective part provided the unit is
returned by the original purchaser, freight prepaid, to:
HAAN Corporation, 44 North Queen Street, Lancaster, PA 17603
The liability under this warranty is limited solely to the cost
of the replacement parts or the complete unit at our option.
Labor charges are not included.
This warranty is extended to the original purchaser of the
unit and excludes all other legal and/or conventional
warranties. The responsibility of HAAN Corporation, if any,
is limited to the specific obligations expressly assumed by
it under the terms of the limited warranty. In no event is
HAAN Corporation liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces
do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights which vary
from state to state or province to province.
IMPORTANT: Carefully pack item to avoid damage in shipping.
Be sure to attach tag to item before packing with your name,
complete address, and phone number with note giving
purchase information, model number and what you believe
is the problem with the item. We recommend you insure the
package (as damage in shipping is not covered by our
warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE.” We are constantly striving to improve
our products; therefore, the specifications contained herein
are subject to change without notice.
pg 18
877-HAAN DIRECT / 877-422-6347
Download from Www.Somanuals.com. All Manuals Search And Download.
(Fold here and tape closed before mailing)
Download from Www.Somanuals.com. All Manuals Search And Download.
Place
Stamp
Here
Product Registration
HAAN Corporation
44 North Queen Street
Lancaster, PA 17603
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|